; -------------------------------------------------------------------------------- ; @Title: IMXRT116X On-Chip Peripherals ; @Props: Released ; @Author: KWI, JON, JDU, NEJ ; @Changelog: 2021-03-17 KWI ; 2022-01-26 JON ; 2023-05-10 JDU ; 2023-10-25 NEJ ; 2023-11-09 NEJ ; @Manufacturer: NXP - NXP Semiconductors ; @Doc: Generated (TRACE32, build: 164352.), based on: ; MIMXRT1165_cm4.xml (Ver. 1.0), MIMXRT1165_cm7.xml (Ver. 1.0), ; MIMXRT1166_cm4.xml (Ver. 1.0), MIMXRT1166_cm7.xml (Ver. 1.0) ; @Core: Cortex-M7F, Cortex-M4F ; @Chip: IMXRT1163-CM4, IMXRT1163-CM7, IMXRT1165-CM4, IMXRT1165-CM7, ; IMXRT1166-CM4, IMXRT1166-CM7 ; @Copyright: (C) 1989-2023 Lauterbach GmbH, licensed for use with TRACE32(R) only ; -------------------------------------------------------------------------------- ; $Id: perimxrt116x.per 16973 2023-11-09 17:44:24Z kwisniewski $ AUTOINDENT.ON CENTER TREE ENUMDELIMITER "," base ad:0x0 sif (CORENAME()=="CORTEXM7F") tree.close "Core Registers (Cortex-M7F)" AUTOINDENT.PUSH AUTOINDENT.OFF tree "System Control" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 12. group.long 0x08++0x03 line.long 0x00 "ACTLR,Auxiliary Control Register" bitfld.long 0x00 28. " DISFPUISSOPT ,DISFPUISSOPT" "No,Yes" bitfld.long 0x00 27. " DISCRITAXIRUW ,Disables critical AXI read-under-write" "No,Yes" bitfld.long 0x00 26. " DISDYNADD ,Disables dynamic allocation of ADD and SUB instructions" "No,Yes" textline " " bitfld.long 0x00 21.--25. " DISISSCH1 ,DISISSCH1" "Normal,Not issued in ch1,,,,,,,,,,,,,,,,,,,,Direct branches,Indirect branches,Loaded to PC,Integer MAC and MUL,VFP,?..." bitfld.long 0x00 16.--20. " DISDI ,DISDI" "Normal,ch1,,,,,,,,,,,,,,,Direct branches,Indirect branches,Loaded to PC,Integer MAC and MUL,VFP,?..." bitfld.long 0x00 15. " DISCRITAXIRUR ,Disables critical AXI read-under-read" "No,Yes" textline " " bitfld.long 0x00 14. " DISBTACALLOC ,DISBTACALLOC" "No,Yes" bitfld.long 0x00 13. " DISBTACREAD ,DISBTACREAD" "No,Yes" bitfld.long 0x00 12. " DISITMATBFLUSH ,Disables ITM and DWT ATB flush" "No,Yes" textline " " bitfld.long 0x00 11. " DISRAMODE ,Disables dynamic read allocate mode for Write-Back Write-Allocate memory regions" "No,Yes" bitfld.long 0x00 10. " FPEXCODIS ,Disables FPU exception outputs" "No,Yes" bitfld.long 0x00 2. " DISFOLD ,Disables dual-issue functionality" "No,Yes" textline "" group.long 0x10++0x03 line.long 0x00 "SYST_CSR,SysTick Control and Status Register" rbitfld.long 0x00 16. " COUNTFLAG ,Counter Flag" "Not counted,Counted" bitfld.long 0x00 2. " CLKSOURCE ,SysTick clock source" "External,Core" bitfld.long 0x00 1. " TICKINT ,SysTick Handler" "No SysTick,SysTick" textline " " bitfld.long 0x00 0. " ENABLE ,Counter Enable" "Disabled,Enabled" group.long 0x14++0x07 line.long 0x00 "SYST_RVR,SysTick Reload Value Register" hexmask.long.tbyte 0x00 0.--23. 1. " RELOAD ,The value to load into the SYST_CVR when the counter reaches 0" line.long 0x04 "SYST_CVR,SysTick Current Value Register" rgroup.long 0x1C++0x03 line.long 0x00 "SYST_CALIB,SysTick Calibration value Register" bitfld.long 0x00 31. " NOREF ,Indicates whether the implementation defined reference clock is implemented" "Implemented,Not implemented" bitfld.long 0x00 30. " SKEW ,Indicates whether the 10ms calibration value is exact" "Exact,Inexact" hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Holds a reload value to be used for 10ms (100Hz) timing" rgroup.long 0xD00++0x03 line.long 0x00 "CPUID,CPUID Base Register" hexmask.long.byte 0x00 24.--31. 1. " IMPLEMENTER ,Indicates implementer" bitfld.long 0x00 20.--23. " VARIANT ,Indicates processor revision" "Revision 0,Revision 1,?..." bitfld.long 0x00 16.--19. " ARCHITECTURE ,Architecture" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 4.--15. 1. " PARTNO ,Indicates part number" bitfld.long 0x00 0.--3. " REVISION ,Indicates patch release" "Patch 0,Patch 1,Patch 2,?..." group.long 0xD04++0x23 line.long 0x00 "ICSR,Interrupt Control and State Register" bitfld.long 0x00 31. " NMIPENDSET ,On writes, makes the NMI exception active. On reads, indicates the state of the exception" "Inactive,Active" setclrfld.long 0x00 28. 0x00 28. 0x00 27. " PENDSVSET ,On writes, sets the PendSV exception as pending. On reads, indicates the current state of the exception" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x00 25. " PENDSTSET ,On writes, sets the SysTick exception as pending. On reads, indicates the current state of the exception" "Not pending,Pending" textline " " rbitfld.long 0x00 23. " ISRPREEMPT ,Indicates whether a pending exception will be serviced on exit from debug halt state" "Disabled,Enabled" rbitfld.long 0x00 22. " ISRPENDING ,Indicates whether an external interrupt, generated by the NVIC, is pending" "Not pending,Pending" hexmask.long.word 0x00 12.--20. 1. " VECTPENDING ,The exception number of the highest priority pending and enabled interrupt" textline " " rbitfld.long 0x00 11. " RETTOBASE ,Indicates whether there is an active exception other than the exception indicated by the current value of the IPSR" "Present,Absent" hexmask.long.word 0x00 0.--8. 1. " VECTACTIVE ,The exception number of the current executing exception" line.long 0x04 "VTOR,Vector Table Offset Register" hexmask.long 0x04 7.--31. 0x80 " TBLOFF ,Bits[31:7] of the vector table address" line.long 0x08 "AIRCR,Application Interrupt and Reset Control Register" hexmask.long.word 0x08 16.--31. 1. " VECTKEYSTAT ,Vector Key" rbitfld.long 0x08 15. " ENDIANNESS ,Indicates the memory system endianness" "Little endian,Big endian" bitfld.long 0x08 8.--10. " PRIGROUP ,Priority grouping. Group priority field bits/Subpriority field bits" "[7:1]/[0],[7:2]/[1:0],[7:3]/[2:0],[7:4]/[3:0],[7:5]/[4:0],[7:6]/[5:0],[7]/[6:0],-/[7:0]" textline " " bitfld.long 0x08 2. " SYSRESETREQ ,System Reset Request" "Not requested,Requested" bitfld.long 0x08 1. " VECTCLRACTIVE ,Writing 1 to this bit clears all active state information for fixed and configurable exceptions" "No effect,Clear" bitfld.long 0x08 0. " VECTRESET ,Writing 1 to this bit causes a local system reset" "No effect,Reset" line.long 0x0C "SCR,System Control Register" bitfld.long 0x0C 4. " SEVONPEND ,Determines whether an interrupt transition from inactive state to pending state is a wakeup event" "Not wakeup,Wakeup" bitfld.long 0x0C 2. " SLEEPDEEP ,Provides a qualifying hint indicating that waking from sleep might take longer" "Not deep sleep,Deep sleep" bitfld.long 0x0C 1. " SLEEPONEXIT ,Determines whether, on an exit from an ISR that returns to the base level of execution priority, the processor enters a sleep state" "Disabled,Enabled" line.long 0x10 "CCR,Configuration and Control Register" bitfld.long 0x10 18. " BP ,Branch prediction enable bit" "Disabled,Enabled" bitfld.long 0x10 17. " IC ,Instruction cache enable bit" "Disabled,Enabled" bitfld.long 0x10 16. " DC ,Cache enable bit" "Disabled,Enabled" textline " " bitfld.long 0x10 9. " STKALIGN ,Determines whether the exception entry sequence guarantees 8-byte stack frame alignment, adjusting the SP if necessary before saving state" "4-byte/no adjustment,8-byte/adjustment" bitfld.long 0x10 8. " BFHFNMIGN ,Determines the effect of precise data access faults on handlers running at priority -1 or priority -2" "Lockup,Ignored" bitfld.long 0x10 4. " DIV_0_TRP ,Controls the trap on divide by 0" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " UNALIGN_TRP ,Controls the trapping of unaligned word or halfword accesses" "Disabled,Enabled" bitfld.long 0x10 1. " USERSETMPEND ,Controls whether unprivileged software can access the STIR" "Disabled,Enabled" bitfld.long 0x10 0. " NONBASETHRDENA ,Controls whether the processor can enter Thread mode at an execution priority level other than base level" "Disabled,Enabled" line.long 0x14 "SHPR1,SSystem Handler Priority Register 1" hexmask.long.byte 0x14 24.--31. 1. " PRI_7 ,Priority of System Handler 7" hexmask.long.byte 0x14 16.--23. 1. " PRI_6 ,Priority of system handler 6(UsageFault)" hexmask.long.byte 0x14 8.--15. 1. " PRI_5 ,Priority of system handler 5(BusFault)" textline " " hexmask.long.byte 0x14 0.--7. 1. " PRI_4 ,Priority of system handler 4(MemManage)" line.long 0x18 "SHPR2,System Handler Priority Register 2" hexmask.long.byte 0x18 24.--31. 1. " PRI_11 ,Priority of system handler 11(SVCall)" hexmask.long.byte 0x18 16.--23. 1. " PRI_10 ,Priority of System Handler 10" hexmask.long.byte 0x18 8.--15. 1. " PRI_9 ,Priority of System Handler 9" textline " " hexmask.long.byte 0x18 0.--7. 1. " PRI_8 ,Priority of System Handler 8" line.long 0x1C "SHPR3,System Handler Priority Register 3" hexmask.long.byte 0x1C 24.--31. 1. " PRI_15 ,Priority of System Handler 15(SysTick)" hexmask.long.byte 0x1C 16.--23. 1. " PRI_14 ,Priority of System Handler 14(PendSV)" hexmask.long.byte 0x1C 8.--15. 1. " PRI_13 ,Priority of System Handler 13" textline " " hexmask.long.byte 0x1C 0.--7. 1. " PRI_12 ,Priority of System Handler 12(DebugMonitor)" line.long 0x20 "SHCSR,System Handler Control and State Register" bitfld.long 0x20 18. " USGFAULTENA ,UsageFault" "Disabled,Enabled" bitfld.long 0x20 17. " BUSFAULTENA ,BusFault" "Disabled,Enabled" bitfld.long 0x20 16. " MEMFAULTENA ,MemManage" "Disabled,Enabled" textline " " bitfld.long 0x20 15. " SVCALLPENDED ,SVCall status" "Not pending,Pending" bitfld.long 0x20 14. " BUSFAULTPENDED ,BusFault status" "Not pending,Pending" bitfld.long 0x20 13. " MEMFAULTPENDED ,MemManage status" "Not pending,Pending" textline " " bitfld.long 0x20 12. " USGFAULTPENDED ,UsageFault status" "Not pending,Pending" bitfld.long 0x20 11. " SYSTICKACT ,SysTick status" "Not active,Active" bitfld.long 0x20 10. " PENDSVACT ,PendSV status" "Not active,Active" textline " " bitfld.long 0x20 8. " MONITORACT ,Monitor status" "Not active,Active" bitfld.long 0x20 7. " SVCALLACT ,SVCall status" "Not active,Active" bitfld.long 0x20 3. " USGFAULTACT ,UsageFault status" "Not active,Active" textline " " bitfld.long 0x20 1. " BUSFAULTACT ,BusFault status" "Not active,Active" bitfld.long 0x20 0. " MEMFAULTACT ,MemManage status" "Not active,Active" group.byte 0xD28++0x1 line.byte 0x00 "MMFSR,MemManage Status Register" bitfld.byte 0x00 7. " MMARVALID ,Address Valid Flag" "Not valid,Valid" bitfld.byte 0x00 5. " MLSPERR ,A MemManage fault occurred during FP lazy state preservation" "Not occurred,Occurred" bitfld.byte 0x00 4. " MSTKERR ,tacking Access Violations" "Not occurred,Occurred" textline " " bitfld.byte 0x00 3. " MUNSTKERR ,Unstack Access Violations" "Not occurred,Occurred" bitfld.byte 0x00 1. " DACCVIOL ,Data Access Violation" "Not occurred,Occurred" bitfld.byte 0x00 0. " IACCVIOL ,Instruction Access Violation" "Not occurred,Occurred" line.byte 0x01 "BFSR,Bus Fault Status Register" bitfld.byte 0x01 7. " BFARVALID ,Address Valid Flag" "Not valid,Valid" bitfld.byte 0x01 5. " LSPERR ,A bus fault occurred during FP lazy state preservation" "Not occurred,Occurred" bitfld.byte 0x01 4. " STKERR ,Derived bus fault(exception entry)" "Not occurred,Occurred" textline " " bitfld.byte 0x01 3. " UNSTKERR ,Derived bus fault(exception return)" "Not occurred,Occurred" bitfld.byte 0x01 2. " IMPRECISERR ,Imprecise data access error" "Not occurred,Occurred" bitfld.byte 0x01 1. " PRECISERR ,Precise data access error" "Not occurred,Occurred" textline " " bitfld.byte 0x01 0. " IBUSERR ,Bus fault on an instruction prefetch" "Not occurred,Occurred" group.word 0xD2A++0x1 line.word 0x00 "USAFAULT,Usage Fault Status Register" bitfld.word 0x00 9. " DIVBYZERO ,Divide by zero error" "No error,Error" bitfld.word 0x00 8. " UNALIGNED ,Unaligned access error" "No error,Error" bitfld.word 0x00 3. " NOCP ,A coprocessor access error" "No error,Error" textline " " bitfld.word 0x00 2. " INVPC ,An integrity check error" "No error,Error" bitfld.word 0x00 1. " INVSTATE ,Invalid Combination of EPSR and Instruction" "No error,Error" bitfld.word 0x00 0. " UNDEFINSTR ,Undefined instruction error" "No error,Error" group.long 0xD2C++0x13 line.long 0x00 "HFSR,HardFault Status Register" eventfld.long 0x00 31. " DEBUGEVT ,Indicates when a Debug event has occurred" "Not occurred,Occurred" eventfld.long 0x00 30. " FORCED ,Indicates that a fault with configurable priority has been escalated to a HardFault exception" "Not occurred,Occurred" eventfld.long 0x00 1. " VECTTBL ,Indicates when a fault has occurred because of a vector table read error on exception processing" "Not occurred,Occurred" line.long 0x04 "DFSR,Debug Fault Status Register" eventfld.long 0x04 4. " EXTERNAL ,Indicates a debug event generated because of the assertion of an external debug request" "Not occurred,Occurred" eventfld.long 0x04 3. " VCATCH ,Indicates triggering of a Vector catch" "Not occurred,Occurred" eventfld.long 0x04 2. " DWTTRAP ,Indicates a debug event generated by the DWT" "Not occurred,Occurred" textline " " eventfld.long 0x04 1. " BKPT ,Indicates a debug event generated by BKPT instruction execution or a breakpoint match in FPB" "Not occurred,Occurred" eventfld.long 0x04 0. " HALTED ,Indicates a debug event generated by a C_HALT or C_STEP request or a step request triggered by setting DEMCR.MON_STEP to 1" "Not occurred,Occurred" line.long 0x08 "MMFAR,MemManage Fault Address Register" line.long 0x0C "BFAR,BusFault Address Register" line.long 0x10 "AFSR,Auxiliary Fault Status Register" group.long 0xD88++0x03 line.long 0x00 "CPACR,Coprocessor Access Control Register" bitfld.long 0x00 22.--23. " CP11 ,Access privileges for coprocessor 11" "Denied,Privileged,,Full" bitfld.long 0x00 20.--21. " CP10 ,Access privileges for coprocessor 10" "Denied,Privileged,,Full" bitfld.long 0x00 14.--15. " CP7 ,Access privileges for coprocessor 7" "Denied,Privileged,,Full" textline " " bitfld.long 0x00 12.--13. " CP6 ,Access privileges for coprocessor 6" "Denied,Privileged,,Full" bitfld.long 0x00 10.--11. " CP5 ,Access privileges for coprocessor 5" "Denied,Privileged,,Full" bitfld.long 0x00 8.--9. " CP4 ,Access privileges for coprocessor 4" "Denied,Privileged,,Full" textline " " bitfld.long 0x00 6.--7. " CP3 ,Access privileges for coprocessor 3" "Denied,Privileged,,Full" bitfld.long 0x00 4.--5. " CP2 ,Access privileges for coprocessor 2" "Denied,Privileged,,Full" bitfld.long 0x00 2.--3. " CP1 ,Access privileges for coprocessor 1" "Denied,Privileged,,Full" textline " " bitfld.long 0x00 0.--1. " CP0 ,Access privileges for coprocessor 0" "Denied,Privileged,,Full" wgroup.long 0xF00++0x03 line.long 0x00 "STIR,Software Triggered Interrupt Register" hexmask.long.word 0x00 0.--8. 1. " INTID ,Indicates the interrupt to be triggered" tree "Memory System" width 10. rgroup.long 0xD78++0x0B line.long 0x00 "CLIDR,Cache Level ID Register" bitfld.long 0x00 27.--29. " LOU ,Level of Unification" "Level 1,level 2,?..." bitfld.long 0x00 24.--26. " LOC ,Level of Coherency" "Level 1,level 2,?..." bitfld.long 0x00 18.--20. " CL7 ,Cache type field level 7" "No cache,?..." textline " " bitfld.long 0x00 15.--17. " CL6 ,Cache type field level 6" "No cache,?..." bitfld.long 0x00 12.--14. " CL5 ,Cache type field level 5" "No cache,?..." bitfld.long 0x00 9.--11. " CL4 ,Cache type field level 4" "No cache,?..." textline " " bitfld.long 0x00 6.--8. " CL3 ,Cache type field level 3" "No cache,?..." bitfld.long 0x00 3.--5. " CL2 ,Cache type field level 2" "No cache,?..." bitfld.long 0x00 0.--2. " CL1 ,Cache type field level 1" "No cache,Instr. only,Data only,Data and Instr.,?..." line.long 0x04 "CTR,Cache Type Register" bitfld.long 0x04 29.--31. " FORMAT ,Indicates the implemented CTR format" ",,,,ARMv7,?..." bitfld.long 0x04 24.--27. " CWG ,Cache Write-back Granule" "0,1,2,3,4,5,6,7,8,9,?..." bitfld.long 0x04 20.--23. " ERG ,Exclusives Reservation Granule" "0,1,2,3,4,5,6,7,8,9,?..." textline " " bitfld.long 0x04 16.--19. " DMINLINE ,Log 2 of the number of words in the smallest cache line of all the data caches and unified caches that are controlled by the processor" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x04 0.--3. " IMINLINE ,Log 2 of the number of words in the smallest cache line of all the instruction caches that are controlled by the processor" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" line.long 0x08 "CCSIDR,Cache Size ID Register" bitfld.long 0x08 31. " WT ,Indicates support available for Write-Through" "Not supported,Supported" bitfld.long 0x08 30. " WB ,Indicates support available for Write-Back" "Not supported,Supported" bitfld.long 0x08 29. " RA ,Indicates support available for read allocation" "Not supported,Supported" textline " " bitfld.long 0x08 28. " WA ,Indicates support available for write allocation" "Not supported,Supported" hexmask.long.word 0x08 13.--27. 1. " NUMSETS ,Indicates the number of sets as (number of sets) - 1" hexmask.long.word 0x08 3.--12. 1. " ASSOCIATIVITY ,Indicates the number of ways as (number of ways) - 1" textline " " bitfld.long 0x08 0.--2. " LINESIZE ,Indicates the number of words in each cache line" "4,8,16,32,64,128,256,512" group.long 0xD84++0x03 line.long 0x00 "CSSELR,Cache Size Selection Register" bitfld.long 0x00 1.--3. " LEVEL ,Identifies which cache level to select" "Level 1,?..." bitfld.long 0x00 0. " IND ,Identifies instruction or data cache to use" "Data,Instruction" wgroup.long 0xF50++0x03 line.long 0x00 "ICIALLU,Instruction cache invalidate all to Point of Unification" wgroup.long 0xF58++0x1F line.long 0x00 "ICIMVAU,Instruction cache invalidate by address to PoU" line.long 0x04 "DCIMVAC,Data cache invalidate by address to Point of Coherency (PoC)" line.long 0x08 "DCISW,Data cache invalidate by set/way" line.long 0x0C "DCCMVAU,Data cache by address to PoU" line.long 0x10 "DCCMVAC,Data cache clean by address to PoC" line.long 0x14 "DCCSW,Data cache clean by set/way" line.long 0x18 "DCCIMVAC,Data cache clean and invalidate by address to PoC" line.long 0x1C "DCCISW,Data cache clean and invalidate by set/way" group.long 0xF90++0x13 line.long 0x00 "ITCMCR,Instruction Tightly-Coupled Memory Control Register" bitfld.long 0x00 3.--6. " SZ ,TCM size" "Not implemented,,,4 KB,8 KB,16 KB,32 KB,64 KB,128 KB,256 KB,512 KB,1 MB,2 MB,4 MB,8 MB,16 MB" bitfld.long 0x00 2. " RETEN ,Retry phase enable" "Disabled,Enabled" bitfld.long 0x00 1. " RMW ,Read-Modify-Write enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " EN ,TCM enable" "Disabled,Enabled" line.long 0x04 "DTCMCR,Data Tightly-Coupled Memory Control Register" bitfld.long 0x04 3.--6. " SZ ,TCM size" "Not implemented,,,4 KB,8 KB,16 KB,32 KB,64 KB,128 KB,256 KB,512 KB,1 MB,2 MB,4 MB,8 MB,16 MB" bitfld.long 0x04 2. " RETEN ,Retry phase enable" "Disabled,Enabled" bitfld.long 0x04 1. " RMW ,Read-Modify-Write enable" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " EN ,TCM enable" "Disabled,Enabled" line.long 0x08 "AHBPCR,AHBP control register" bitfld.long 0x08 1.--3. " SZ ,AHBP size" "AHBP disabled,64 MB,128 MB,256 MB,512 MB,?..." bitfld.long 0x08 0. " EN ,AHBP enable" "Disabled,Enabled" line.long 0x0C "CACR,L1 Cache Control Register" bitfld.long 0x0C 2. " FORCEWT ,Enables Force Write-through in the data cache" "Disabled,Enabled" bitfld.long 0x0C 1. " ECCDIS ,Disables ECC in the instruction and data cache" "No,Yes" bitfld.long 0x0C 0. " SIWT ,Enables limited cache coherency usage" "Disabled,Enabled" line.long 0x10 "AHBSCR,AHB Slave Control Register" bitfld.long 0x10 11.--15. " INITCOUNT ,Fairness counter initialization value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" hexmask.long.word 0x10 2.--10. 1. " TPRI ,Threshold execution priority for AHBS traffic demotion" bitfld.long 0x10 0.--1. " CTL ,AHBS prioritization control" "AHBS,Software,AHBSCR.INITCOUNT,AHBSPRI" group.long 0xFA8++0x03 line.long 0x00 "ABFSR,Auxiliary Bus Fault Status Register" bitfld.long 0x00 8.--9. " AXIMTYPE ,Indicates the type of fault on the AXIM interface" "OKAY,EXOKAY,SLVERR,DECERR" bitfld.long 0x00 4. " EPPB ,Asynchronous fault on EPPB interface" "Not occurred,Occurred" bitfld.long 0x00 3. " AXIM ,Asynchronous fault on AXIM interface" "Not occurred,Occurred" textline " " bitfld.long 0x00 2. " AHBP ,Asynchronous fault on AHBP interface" "Not occurred,Occurred" bitfld.long 0x00 1. " DTCM ,Asynchronous fault on DTCM interface" "Not occurred,Occurred" bitfld.long 0x00 0. " ITCM ,Asynchronous fault on ITCM interface" "Not occurred,Occurred" group.long 0xFB0++0x03 line.long 0x00 "IEBR0,Instruction Error bank Register 0" bitfld.long 0x00 30.--31. " UD ,User-defined" "0,1,2,3" bitfld.long 0x00 17. " TOE ,Indicates the error type" "Correctable,Non-correctable" bitfld.long 0x00 16. " RB ,Indicates which RAM bank to use" "Tag,Data" textline " " hexmask.long.word 0x00 2.--15. 0x4 " RL ,Indicates the location in instruction cache RAM" bitfld.long 0x00 1. " LOCKED ,Indicates whether the location is locked or not locked" "Not locked,Locked" bitfld.long 0x00 0. " VALID ,Indicates whether the entry is valid or not" "Not valid,Valid" group.long 0xFB4++0x03 line.long 0x00 "IEBR1,Instruction Error bank Register 1" bitfld.long 0x00 30.--31. " UD ,User-defined" "0,1,2,3" bitfld.long 0x00 17. " TOE ,Indicates the error type" "Correctable,Non-correctable" bitfld.long 0x00 16. " RB ,Indicates which RAM bank to use" "Tag,Data" textline " " hexmask.long.word 0x00 2.--15. 0x4 " RL ,Indicates the location in instruction cache RAM" bitfld.long 0x00 1. " LOCKED ,Indicates whether the location is locked or not locked" "Not locked,Locked" bitfld.long 0x00 0. " VALID ,Indicates whether the entry is valid or not" "Not valid,Valid" group.long 0xFB8++0x03 line.long 0x00 "DEBR0,Data Error bank Register 0" bitfld.long 0x00 30.--31. " UD ,User-defined" "0,1,2,3" bitfld.long 0x00 17. " TOE ,Indicates the error type" "Correctable,Non-correctable" bitfld.long 0x00 16. " RB ,Indicates which RAM bank to use" "Tag,Data" textline " " hexmask.long.word 0x00 2.--15. 0x4 " RL ,Indicates the location in instruction cache RAM" bitfld.long 0x00 1. " LOCKED ,Indicates whether the location is locked or not locked" "Not locked,Locked" bitfld.long 0x00 0. " VALID ,Indicates whether the entry is valid or not" "Not valid,Valid" group.long 0xFBC++0x03 line.long 0x00 "DEBR1,Data Error bank Register 1" bitfld.long 0x00 30.--31. " UD ,User-defined" "0,1,2,3" bitfld.long 0x00 17. " TOE ,Indicates the error type" "Correctable,Non-correctable" bitfld.long 0x00 16. " RB ,Indicates which RAM bank to use" "Tag,Data" textline " " hexmask.long.word 0x00 2.--15. 0x4 " RL ,Indicates the location in instruction cache RAM" bitfld.long 0x00 1. " LOCKED ,Indicates whether the location is locked or not locked" "Not locked,Locked" bitfld.long 0x00 0. " VALID ,Indicates whether the entry is valid or not" "Not valid,Valid" tree.end tree "Feature Registers" width 10. rgroup.long 0xD40++0x0B line.long 0x00 "ID_PFR0,Processor Feature Register 0" bitfld.long 0x00 4.--7. " STATE1 ,Thumb instruction set support" ",,,Supported,?..." bitfld.long 0x00 0.--3. " STATE0 ,ARM instruction set support" "Not supported,?..." line.long 0x04 "ID_PFR1,Processor Feature Register 1" bitfld.long 0x04 8.--11. " MPROF ,M profile programmers' model" ",,2-stack,?..." line.long 0x08 "ID_DFR0,Debug Feature Register 0" bitfld.long 0x08 20.--23. " DBGMOD ,Support for memory-mapped debug model for M profile processors" "Not supported,Supported,?..." hgroup.long 0xD4C++0x03 hide.long 0x00 "ID_AFR0,Auxiliary Feature Register 0" rgroup.long 0xD50++0x03 line.long 0x00 "ID_MMFR0,Memory Model Feature Register 0" bitfld.long 0x00 20.--23. " AUXREG ,Indicates the support for Auxiliary registers" "Not supported,ACTLR only,?..." bitfld.long 0x00 16.--19. " TCMSUP ,Indicates the support for Tightly Coupled Memory (TCM)" "Not supported,Supported,?..." bitfld.long 0x00 12.--15. " SHRLEV ,Indicates the number of shareability levels implemented" "Level 1,?..." textline " " bitfld.long 0x00 8.--11. " OUTMSHR ,Indicates the outermost shareability domain implemented" "Non-cacheable,,,,,,,,,,,,,,,Ignored" bitfld.long 0x00 4.--7. " PMSASUP ,Indicates support for a PMSA" "Not supported,,,PMSAv7,?..." hgroup.long 0xD54++0x03 hide.long 0x00 "ID_MMFR1,Memory Model Feature Register 1" rgroup.long 0xD58++0x03 line.long 0x00 "ID_MMFR2,Memory Model Feature Register 2" bitfld.long 0x00 24.--27. " WFISTALL ,Indicates the support for Wait For Interrupt (WFI) stalling" "Not supported,Supported,?..." rgroup.long 0xD60++0x13 line.long 0x00 "ID_ISAR0,Instruction Set Attributes Register 0" bitfld.long 0x00 24.--27. " DIVIDE ,Indicates the supported divide instructions" "Not supported,SDIV/UDIV,?..." bitfld.long 0x00 20.--23. " DEBUG ,Indicates the supported debug instructions" "Not supported,BKPT,?..." bitfld.long 0x00 16.--19. " COPROC ,Indicates the supported coprocessor instructions" "Not supported,CDP/LDC/MCR/STC,CDP2/LDC2/MCR2/STC2,MCRR/MRRC,MCRR2/MRRC2,?..." textline " " bitfld.long 0x00 12.--15. " CMPBRANCH ,Indicates the supported combined compare and branch instructions" "Not supported,CBNZ/CBZ,?..." bitfld.long 0x00 8.--11. " BITFIELD ,Indicates the supported bitfield instructions" "Not supported,BFC/BFI/SBFX/UBFX,?..." bitfld.long 0x00 4.--7. " BITCOUNT ,Indicates the supported bit counting instructions" "Not supported,CLZ,?..." line.long 0x04 "ID_ISAR1,Instruction Set Attributes Register 1" bitfld.long 0x04 24.--27. " INTERWORK ,Indicates the supported Interworking instructions" "Not supported,BX,BX/BLX,?..." bitfld.long 0x04 20.--23. " IMMEDIATE ,Indicates the support for data-processing instructions with long immediates" "Not supported,ADDW/MOVW/MOVT/SUBW,?..." bitfld.long 0x04 16.--19. " IFTHEN ,Indicates the supported IfThen instructions" "Not supported,IT,?..." textline " " bitfld.long 0x04 12.--15. " EXTEND ,Indicates the supported Extend instructions" "Not supported,Supported,Supported,?..." line.long 0x08 "ID_ISAR2,Instruction Set Attributes Register 2" bitfld.long 0x08 24.--27. " REVERSAL ,Indicates the supported reversal instructions" "Not supported,REV/REV16/REVSH,REV/REV16/REVSH/RBIT,?..." bitfld.long 0x08 20.--23. " MULTU ,Indicates the supported advanced unsigned multiply instructions" "Not supported,UMULL/UMLAL,UMULL/UMLAL/UMAAL,?..." bitfld.long 0x08 16.--19. " MULTS ,Indicates the supported advanced signed multiply instructions" "Not supported,Supported,Supported,Supported,?..." textline " " bitfld.long 0x08 12.--15. " MULT ,Indicates the supported additional multiply instructions" "Not supported,MLA,MLA/MLS,?..." bitfld.long 0x08 8.--11. " MULTIACCESSINT ,Indicates the support for multi-access interruptible instructions" "Not supported,LDM/STM restartable,LDM/STM continuable,?..." bitfld.long 0x08 4.--7. " MEMHINT ,Indicates the supported memory hint instructions" "Not supported,,,PLD/PLI,?..." textline " " bitfld.long 0x08 0.--3. " LOADSTORE ,Indicates the supported additional load and store instructions" "Not supported,LDRD/STRD,?..." line.long 0x0C "ID_ISAR3,Instruction Set Attributes Register 3" bitfld.long 0x0C 24.--27. " TRUENOP ,Indicates the support for a true NOP instruction" "Not supported,Supported,?..." bitfld.long 0x0C 20.--23. " THUMBCOPY ,Indicates the supported non flag-setting MOV instructions" "Not supported,Supported,?..." bitfld.long 0x0C 16.--19. " TABBRANCH ,Indicates the supported Table Branch instructions" "Not supported,TBB/TBH,?..." textline " " bitfld.long 0x0C 12.--15. " SYNCHPRIM ,Indicates the supported Table Branch instructions" "Not supported,Supported,Supported,Supported,?..." bitfld.long 0x0C 8.--11. " SVC ,Indicates the supported SVC instructions" "Not supported,SVC,?..." bitfld.long 0x0C 4.--7. " SIMD ,Indicates the supported SIMD instructions" "Not supported,Supported,,Supported,?..." textline " " bitfld.long 0x0C 0.--3. " SATURATE ,Indicates the supported Saturate instructions" "Not supported,QADD/QDADD/QDSUB/QSUB,?..." line.long 0x10 "ID_ISAR4,Instruction Set Attributes Register 4" bitfld.long 0x10 24.--27. " PSR_M ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,?..." bitfld.long 0x10 20.--23. " SYNCHPRIMFRAC ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,Supported,Supported,?..." bitfld.long 0x10 16.--19. " BARRIER ,Indicates the supported Barrier instructions" "Not supported,DMB/DSB/ISB,?..." textline " " bitfld.long 0x10 8.--11. " WRITEBACK ,Indicates the support for writeback addressing modes" "Basic support,Full support,?..." bitfld.long 0x10 4.--7. " WITHSHIFTS ,Indicates the support for instructions with shifts" "MOV/shift,Shift LSL 0-3,,Shift other,?..." bitfld.long 0x10 0.--3. " UNPRIV ,Indicates the supported unprivileged instructions" "Not supported,LDRBT/LDRT/STRBT/STRT,LDRBT/LDRT/STRBT/STRT/LDRHT/LDRSBT/LDRSHTSTRHT,?..." tree.end tree "CoreSight Identification Registers" width 6. rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0C "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0C "CID3,Component ID3" tree.end width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Memory Protection Unit (MPU)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 15. rgroup.long 0xD90++0x03 line.long 0x00 "MPU_TYPE,MPU Type Register" bitfld.long 0x00 16.--23. " IREGION ,Instruction region" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..." bitfld.long 0x00 8.--15. " DREGION ,Number of regions supported by the MPU" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..." bitfld.long 0x00 0. " SEPARATE ,Indicates support for separate instruction and data address maps" "Not supported,Supported" group.long 0xD94++0x03 line.long 0x00 "MPU_CTRL,MPU Control Register" bitfld.long 0x00 2. " PRIVDEFENA ,Enables the default memory map as a background region for privileged access" "Disabled,Enabled" bitfld.long 0x00 1. " HFNMIENA ,Handlers executing with priority less than 0 access memory with the MPU enabled or with the MPU disabled" "MPU disabled,MPU enabled" bitfld.long 0x00 0. " ENABLE ,Enables the MPU" "Disabled,Enabled" group.long 0xD98++0x03 line.long 0x00 "MPU_RNR,MPU Region Number Register" hexmask.long.byte 0x00 0.--7. 1. " REGION ,Indicates the memory region accessed by MPU_RBAR and MPU_RASR" tree.close "MPU regions" if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x0 group.long 0xD9C++0x03 "Region 0" saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 0 (not implemented)" saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x1 group.long 0xD9C++0x03 "Region 1" saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 1 (not implemented)" saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x2 group.long 0xD9C++0x03 "Region 2" saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 2 (not implemented)" saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x3 group.long 0xD9C++0x03 "Region 3" saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 3 (not implemented)" saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x4 group.long 0xD9C++0x03 "Region 4" saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 4 (not implemented)" saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x5 group.long 0xD9C++0x03 "Region 5" saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 5 (not implemented)" saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x6 group.long 0xD9C++0x03 "Region 6" saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 6 (not implemented)" saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x7 group.long 0xD9C++0x03 "Region 7" saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 7 (not implemented)" saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x8 group.long 0xD9C++0x03 "Region 8" saveout 0xD98 %l 0x8 line.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x8 line.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 8 (not implemented)" saveout 0xD98 %l 0x8 hide.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x8 hide.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x9 group.long 0xD9C++0x03 "Region 9" saveout 0xD98 %l 0x9 line.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x9 line.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 9 (not implemented)" saveout 0xD98 %l 0x9 hide.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x9 hide.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xA group.long 0xD9C++0x03 "Region 10" saveout 0xD98 %l 0xA line.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xA line.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 10 (not implemented)" saveout 0xD98 %l 0xA hide.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xA hide.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xB group.long 0xD9C++0x03 "Region 11" saveout 0xD98 %l 0xB line.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xB line.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 11 (not implemented)" saveout 0xD98 %l 0xB hide.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xB hide.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xC group.long 0xD9C++0x03 "Region 12" saveout 0xD98 %l 0xC line.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xC line.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 12 (not implemented)" saveout 0xD98 %l 0xC hide.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xC hide.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xD group.long 0xD9C++0x03 "Region 13" saveout 0xD98 %l 0xD line.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xD line.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 13 (not implemented)" saveout 0xD98 %l 0xD hide.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xD hide.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xE group.long 0xD9C++0x03 "Region 14" saveout 0xD98 %l 0xE line.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xE line.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 14 (not implemented)" saveout 0xD98 %l 0xE hide.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xE hide.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xF group.long 0xD9C++0x03 "Region 15" saveout 0xD98 %l 0xF line.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xF line.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 15 (not implemented)" saveout 0xD98 %l 0xF hide.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xF hide.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15" textline " " textline " " endif tree.end width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Nested Vectored Interrupt Controller (NVIC)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 6. rgroup.long 0x04++0x03 line.long 0x00 "ICTR,Interrupt Controller Type Register" bitfld.long 0x00 0.--3. " INTLINESNUM ,Total Number of Interrupt" "0-32,33-64,65-96,97-128,129-160,161-192,193-224,225-240,?..." tree "Interrupt Enable Registers" width 23. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x100++0x03 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x100++0x7 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x100++0x0B line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x100++0x0F line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x100++0x13 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x100++0x17 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x100++0x1B line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x100++0x1F line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " ENA239 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " ENA238 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " ENA237 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " ENA236 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " ENA235 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " ENA234 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " ENA233 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " ENA232 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " ENA231 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " ENA230 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " ENA229 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " ENA228 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " ENA227 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " ENA226 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " ENA225 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " ENA224 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" else hgroup.long 0x100++0x1F hide.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" hide.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" hide.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" hide.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" hide.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" hide.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" hide.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" hide.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register" endif tree.end tree "Interrupt Pending Registers" width 23. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x200++0x03 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x200++0x07 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x200++0x0B line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x200++0x0F line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x200++0x13 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x200++0x17 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x200++0x1B line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x200++0x1F line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " PEN239 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " PEN238 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " PEN237 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " PEN236 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " PEN235 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " PEN234 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " PEN233 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " PEN232 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " PEN231 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " PEN230 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " PEN229 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " PEN228 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " PEN227 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " PEN226 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " PEN225 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " PEN224 ,Interrupt Set/Clear Pending" "Not pending,Pending" else hgroup.long 0x200++0x1F hide.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register" endif tree.end tree "Interrupt Active Bit Registers" width 9. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) rgroup.long 0x300++0x03 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) rgroup.long 0x300++0x07 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) rgroup.long 0x300++0x0B line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) rgroup.long 0x300++0x0F line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) rgroup.long 0x300++0x13 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) rgroup.long 0x300++0x17 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) rgroup.long 0x300++0x1B line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" line.long 0x18 "ACTIVE7,Active Bit Register 7" bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) rgroup.long 0x300++0x1F line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" line.long 0x18 "ACTIVE7,Active Bit Register 7" bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active" line.long 0x1c "ACTIVE8,Active Bit Register 8" bitfld.long 0x1c 15. " ACTIVE239 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 14. " ACTIVE238 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 13. " ACTIVE237 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 12. " ACTIVE236 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 11. " ACTIVE235 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 10. " ACTIVE234 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x1c 9. " ACTIVE233 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 8. " ACTIVE232 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 7. " ACTIVE231 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 6. " ACTIVE230 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 5. " ACTIVE229 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 4. " ACTIVE228 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x1c 3. " ACTIVE227 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 2. " ACTIVE226 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 1. " ACTIVE225 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 0. " ACTIVE224 ,Interrupt Active Flag" "Not active,Active" else hgroup.long 0x300++0x1F hide.long 0x00 "ACTIVE1,Active Bit Register 1" hide.long 0x04 "ACTIVE2,Active Bit Register 2" hide.long 0x08 "ACTIVE3,Active Bit Register 3" hide.long 0x0c "ACTIVE4,Active Bit Register 4" hide.long 0x10 "ACTIVE5,Active Bit Register 5" hide.long 0x14 "ACTIVE6,Active Bit Register 6" hide.long 0x18 "ACTIVE7,Active Bit Register 7" hide.long 0x1c "ACTIVE8,Active Bit Register 8" endif tree.end tree "Interrupt Priority Registers" if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x400++0x1F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x400++0x3F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x400++0x5F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x400++0x7F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x400++0x9F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x400++0xBF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x400++0xDF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" line.long 0xC0 "IPR48,Interrupt Priority Register" hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority" hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority" hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority" hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority" line.long 0xC4 "IPR49,Interrupt Priority Register" hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority" hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority" hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority" hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority" line.long 0xC8 "IPR50,Interrupt Priority Register" hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority" hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority" hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority" hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority" line.long 0xCC "IPR51,Interrupt Priority Register" hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority" hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority" hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority" hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority" line.long 0xD0 "IPR52,Interrupt Priority Register" hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority" hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority" hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority" hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority" line.long 0xD4 "IPR53,Interrupt Priority Register" hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority" hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority" hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority" hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority" line.long 0xD8 "IPR54,Interrupt Priority Register" hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority" hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority" hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority" hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority" line.long 0xDC "IPR55,Interrupt Priority Register" hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority" hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority" hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority" hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x400++0xEF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" line.long 0xC0 "IPR48,Interrupt Priority Register" hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority" hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority" hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority" hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority" line.long 0xC4 "IPR49,Interrupt Priority Register" hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority" hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority" hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority" hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority" line.long 0xC8 "IPR50,Interrupt Priority Register" hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority" hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority" hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority" hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority" line.long 0xCC "IPR51,Interrupt Priority Register" hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority" hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority" hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority" hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority" line.long 0xD0 "IPR52,Interrupt Priority Register" hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority" hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority" hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority" hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority" line.long 0xD4 "IPR53,Interrupt Priority Register" hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority" hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority" hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority" hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority" line.long 0xD8 "IPR54,Interrupt Priority Register" hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority" hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority" hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority" hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority" line.long 0xDC "IPR55,Interrupt Priority Register" hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority" hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority" hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority" hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority" line.long 0xE0 "IPR56,Interrupt Priority Register" hexmask.long.byte 0xE0 24.--31. 1. " PRI_227 ,Interrupt 227 Priority" hexmask.long.byte 0xE0 16.--23. 1. " PRI_226 ,Interrupt 226 Priority" hexmask.long.byte 0xE0 8.--15. 1. " PRI_225 ,Interrupt 225 Priority" hexmask.long.byte 0xE0 0.--7. 1. " PRI_224 ,Interrupt 224 Priority" line.long 0xE4 "IPR57,Interrupt Priority Register" hexmask.long.byte 0xE4 24.--31. 1. " PRI_231 ,Interrupt 231 Priority" hexmask.long.byte 0xE4 16.--23. 1. " PRI_230 ,Interrupt 230 Priority" hexmask.long.byte 0xE4 8.--15. 1. " PRI_229 ,Interrupt 229 Priority" hexmask.long.byte 0xE4 0.--7. 1. " PRI_228 ,Interrupt 228 Priority" line.long 0xE8 "IPR58,Interrupt Priority Register" hexmask.long.byte 0xE8 24.--31. 1. " PRI_235 ,Interrupt 235 Priority" hexmask.long.byte 0xE8 16.--23. 1. " PRI_234 ,Interrupt 234 Priority" hexmask.long.byte 0xE8 8.--15. 1. " PRI_233 ,Interrupt 233 Priority" hexmask.long.byte 0xE8 0.--7. 1. " PRI_232 ,Interrupt 232 Priority" line.long 0xEC "IPR59,Interrupt Priority Register" hexmask.long.byte 0xEC 24.--31. 1. " PRI_239 ,Interrupt 239 Priority" hexmask.long.byte 0xEC 16.--23. 1. " PRI_238 ,Interrupt 238 Priority" hexmask.long.byte 0xEC 8.--15. 1. " PRI_237 ,Interrupt 237 Priority" hexmask.long.byte 0xEC 0.--7. 1. " PRI_236 ,Interrupt 236 Priority" else hgroup.long 0x400++0xEF hide.long 0x0 "IPR0,Interrupt Priority Register" hide.long 0x4 "IPR1,Interrupt Priority Register" hide.long 0x8 "IPR2,Interrupt Priority Register" hide.long 0xC "IPR3,Interrupt Priority Register" hide.long 0x10 "IPR4,Interrupt Priority Register" hide.long 0x14 "IPR5,Interrupt Priority Register" hide.long 0x18 "IPR6,Interrupt Priority Register" hide.long 0x1C "IPR7,Interrupt Priority Register" hide.long 0x20 "IPR8,Interrupt Priority Register" hide.long 0x24 "IPR9,Interrupt Priority Register" hide.long 0x28 "IPR10,Interrupt Priority Register" hide.long 0x2C "IPR11,Interrupt Priority Register" hide.long 0x30 "IPR12,Interrupt Priority Register" hide.long 0x34 "IPR13,Interrupt Priority Register" hide.long 0x38 "IPR14,Interrupt Priority Register" hide.long 0x3C "IPR15,Interrupt Priority Register" hide.long 0x40 "IPR16,Interrupt Priority Register" hide.long 0x44 "IPR17,Interrupt Priority Register" hide.long 0x48 "IPR18,Interrupt Priority Register" hide.long 0x4C "IPR19,Interrupt Priority Register" hide.long 0x50 "IPR20,Interrupt Priority Register" hide.long 0x54 "IPR21,Interrupt Priority Register" hide.long 0x58 "IPR22,Interrupt Priority Register" hide.long 0x5C "IPR23,Interrupt Priority Register" hide.long 0x60 "IPR24,Interrupt Priority Register" hide.long 0x64 "IPR25,Interrupt Priority Register" hide.long 0x68 "IPR26,Interrupt Priority Register" hide.long 0x6C "IPR27,Interrupt Priority Register" hide.long 0x70 "IPR28,Interrupt Priority Register" hide.long 0x74 "IPR29,Interrupt Priority Register" hide.long 0x78 "IPR30,Interrupt Priority Register" hide.long 0x7C "IPR31,Interrupt Priority Register" hide.long 0x80 "IPR32,Interrupt Priority Register" hide.long 0x84 "IPR33,Interrupt Priority Register" hide.long 0x88 "IPR34,Interrupt Priority Register" hide.long 0x8C "IPR35,Interrupt Priority Register" hide.long 0x90 "IPR36,Interrupt Priority Register" hide.long 0x94 "IPR37,Interrupt Priority Register" hide.long 0x98 "IPR38,Interrupt Priority Register" hide.long 0x9C "IPR39,Interrupt Priority Register" hide.long 0xA0 "IPR40,Interrupt Priority Register" hide.long 0xA4 "IPR41,Interrupt Priority Register" hide.long 0xA8 "IPR42,Interrupt Priority Register" hide.long 0xAC "IPR43,Interrupt Priority Register" hide.long 0xB0 "IPR44,Interrupt Priority Register" hide.long 0xB4 "IPR45,Interrupt Priority Register" hide.long 0xB8 "IPR46,Interrupt Priority Register" hide.long 0xBC "IPR47,Interrupt Priority Register" hide.long 0xC0 "IPR48,Interrupt Priority Register" hide.long 0xC4 "IPR49,Interrupt Priority Register" hide.long 0xC8 "IPR50,Interrupt Priority Register" hide.long 0xCC "IPR51,Interrupt Priority Register" hide.long 0xD0 "IPR52,Interrupt Priority Register" hide.long 0xD4 "IPR53,Interrupt Priority Register" hide.long 0xD8 "IPR54,Interrupt Priority Register" hide.long 0xDC "IPR55,Interrupt Priority Register" hide.long 0xE0 "IPR56,Interrupt Priority Register" hide.long 0xE4 "IPR57,Interrupt Priority Register" hide.long 0xE8 "IPR58,Interrupt Priority Register" hide.long 0xEC "IPR59,Interrupt Priority Register" endif tree.end width 0x0b else newline textline "COREDEBUG component base address not specified" newline endif tree.end sif CORENAME()=="CORTEXM7F" tree "Floating-point Unit (FPU)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 8. group.long 0xF34++0x0B line.long 0x00 "FPCCR,Floating-Point Context Control Register" bitfld.long 0x00 31. " ASPEN ,Execution of a floating-point instruction sets the CONTROL.FPCA bit to 1" "Disabled,Enabled" bitfld.long 0x00 30. " LSPEN ,Enables lazy context save of FP state" "Disabled,Enabled" bitfld.long 0x00 8. " MONRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the DebugMonitor exception to pending" "Not able,Able" newline bitfld.long 0x00 6. " BFRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the BusFault exception to pending" "Not able,Able" bitfld.long 0x00 5. " MMRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the MemManage exception to pending" "Not able,Able" bitfld.long 0x00 4. " HFRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the HardFault exception to pending" "Not able,Able" newline bitfld.long 0x00 3. " THREAD ,Indicates the processor mode when it allocated the FP stack frame" "Handler,Thread" bitfld.long 0x00 1. " USER ,Indicates the privilege level of the software executing" "Privileged,Unprivileged" bitfld.long 0x00 0. " LSPACT ,Indicates whether Lazy preservation of the FP state is active" "Not active,Active" line.long 0x04 "FPCAR,Floating-Point Context Address Register" hexmask.long 0x04 3.--31. 0x8 " ADDRESS ,The location of the unpopulated floating-point register space allocated on an exception stack frame" line.long 0x08 "FPDSCR,Floating-Point Default Status Control Register" bitfld.long 0x08 26. " AHP ,Default value for FPSCR.AHP" "IEEE 754-2008,Alternative" bitfld.long 0x08 25. " DN ,Default value for FPSCR.DN" "NaN operands,Any operation" bitfld.long 0x08 24. " FZ ,Default value for FPSCR.FZ" "No Flush mode,Flush mode" newline bitfld.long 0x08 22.--23. " RMODE ,Default value for FPSCR.RMode" "Round to Nearest,Round towards Plus Infinity,Round towards Minus Infinity,Round towards Zero" rgroup.long 0xF40++0x0B line.long 0x00 "MVFR0,Media and FP Feature Register 0" bitfld.long 0x00 28.--31. " FPRNDMOD ,Indicates the rounding modes supported by the FP floating-point hardware" ",All supported,?..." bitfld.long 0x00 24.--27. " SRTERR ,Indicates the hardware support for FP short vectors" "Not supported,?..." bitfld.long 0x00 20.--23. " SQRROOT ,Indicates the hardware support for FP square root operations" ",Supported,?..." newline bitfld.long 0x00 16.--19. " DIV ,Indicates the hardware support for FP divide operations" ",Supported,?..." bitfld.long 0x00 12.--15. " FPEXTRP ,Indicates whether the FP hardware implementation supports exception trapping" "Not supported,?..." bitfld.long 0x00 8.--11. " DBLPREC ,Indicates the hardware support for FP double_precision operations" "Not supported,,Supported,?..." newline bitfld.long 0x00 4.--7. " SNGLPREC ,Indicates the hardware support for FP single-precision operations" ",,Supported,?..." bitfld.long 0x00 0.--3. " A_SIMD ,Indicates the size of the FP register bank" ",Supported-16x64-bit,?..." line.long 0x04 "MVFR1,Media and FP Feature Register 1" bitfld.long 0x04 28.--31. " FP_FUSED_MAC ,Indicates whether the FP supports fused multiply accumulate operations" ",Supported,?..." bitfld.long 0x04 24.--27. " FP_HPFP ,Indicates whether the FP supports half-precision and double-precision floating-point conversion instructions" ",Half-single,Half-single and half-double,?..." newline bitfld.long 0x04 4.--7. " D_NAN ,Indicates whether the FP hardware implementation supports only the Default NaN mode" ",NaN propagation,?..." bitfld.long 0x04 0.--3. " FTZ_MODE ,Indicates whether the FP hardware implementation supports only the Flush-to-Zero mode of operation" ",Full denorm. num. arit.,?..." line.long 0x08 "MVFR2,Media and FP Feature Register 2" bitfld.long 0x08 4.--7. " VFP_MISC ,Indicates the hardware support for FP miscellaneous features" "Not supported,,,,Supported,?..." width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end endif tree "Debug" tree "Core Debug" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 7. group.long 0xD30++0x03 line.long 0x00 "DFSR,Debug Fault Status Register" eventfld.long 0x00 4. " EXTERNAL ,Indicates a debug event generated because of the assertion of an external debug request" "Not generated,Generated" eventfld.long 0x00 3. " VCATCH ,Indicates triggering of a Vector catch" "Not triggered,Triggered" eventfld.long 0x00 2. " DWTTRAP ,Indicates a debug event generated by the DWT" "Not generated,Generated" newline eventfld.long 0x00 1. " BKPT ,Indicates a debug event generated by BKPT instruction execution or a breakpoint match in FPB" "Not generated,Generated" eventfld.long 0x00 0. " HALTED ,Indicates a debug event generated by either a C_HALT or C_STEP request, triggered by a write to the DHCSR or a step request triggered by setting DEMCR.MON_STEP to 1" "Not generated,Generated" newline hgroup.long 0xDF0++0x03 hide.long 0x00 "DHCSR,Debug Halting Control and Status Register" in newline wgroup.long 0xDF4++0x03 line.long 0x00 "DCRSR,Debug Core Register Selector Register" bitfld.long 0x00 16. " REGWNR ,Specifies the access type for the transfer" "Read,Write" hexmask.long.byte 0x00 0.--6. 1. " REGSEL ,Specifies the ARM core register, special-purpose register or Floating-point extension register" group.long 0xDF8++0x03 line.long 0x00 "DCRDR,Debug Core Register Data Register" if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDFC))&0x10000)==0x10000) group.long 0xDFC++0x03 line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register" bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled" bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1" bitfld.long 0x00 18. " MON_STEP ,Setting this bit to 1 makes the step request pending" "No step,Step" newline bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending" bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled" bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled" newline bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap on a fault occurring during exception entry or exception return" "Disabled,Enabled" bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled" bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception caused by a state information error" "Disabled,Enabled" newline bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception caused by a checking error" "Disabled,Enabled" bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled" bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled" newline bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled" else group.long 0xDFC++0x03 line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register" bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled" bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1" newline bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending" bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled" bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled" newline bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap on a fault occurring during exception entry or exception return" "Disabled,Enabled" bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled" bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception caused by a state information error" "Disabled,Enabled" newline bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception caused by a checking error" "Disabled,Enabled" bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled" bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled" newline bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled" endif width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Flash Patch and Breakpoint Unit (FPB)" sif COMPonent.AVAILABLE("FPB") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1)) width 10. group.long 0x00++0x03 line.long 0x00 "FP_CTRL,Flash Patch Control Register" bitfld.long 0x00 28.--31. " REV ,Flash Patch Breakpoint architecture revision" "Version 1,Version 2,?..." rbitfld.long 0x00 4.--7. 12.--14. " NUM_CODE ,The number of instruction address comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127" bitfld.long 0x00 1. " KEY ,Key Field" "Low,High" bitfld.long 0x00 0. " ENABLE ,Flash Patch Unit Enable" "Disabled,Enabled" newline if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x8))&0x01)==0x00) group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0xC))&0x01)==0x00) group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x10))&0x01)==0x00) group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x14))&0x01)==0x00) group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x18))&0x01)==0x00) group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x1C))&0x01)==0x00) group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x20))&0x01)==0x00) group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x24))&0x01)==0x00) group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif width 6. tree "CoreSight Identification Registers" rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0c "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0C "CID3,Component ID3" tree.end else newline textline "FPB component base address not specified" newline endif tree.end tree "Data Watchpoint and Trace Unit (DWT)" sif COMPonent.AVAILABLE("DWT") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1)) width 15. group.long 0x00++0x1B line.long 0x00 "DWT_CTRL,Control Register" rbitfld.long 0x00 28.--31. " NUMCOMP ,Number of comparators implemented" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x00 27. " NOTRCPKT ,Shows whether the implementation supports trace sampling and exception tracing" "Supported,Not supported" rbitfld.long 0x00 26. " NOEXTTRIG ,Shows whether the implementation includes external match signals" "Supported,Not supported" newline rbitfld.long 0x00 25. " NOCYCCNT ,Shows whether the implementation supports a cycle counter" "Supported,Not supported" rbitfld.long 0x00 24. " NOPRFCNT ,Shows whether the implementation supports the profiling counters" "Supported,Not supported" bitfld.long 0x00 22. " CYCEVTENA ,Enables POSTCNT underflow Event counter packets generation" "Disabled,Enabled" newline bitfld.long 0x00 21. " FOLDEVTENA ,Enables generation of the Folded-instruction counter overflow event" "Disabled,Enabled" bitfld.long 0x00 20. " LSUEVTENA ,Enables generation of the LSU counter overflow event" "Disabled,Enabled" bitfld.long 0x00 19. " SLEEPEVTENA ,Enables generation of the Sleep counter overflow event" "Disabled,Enabled" newline bitfld.long 0x00 18. " EXCEVTENA ,Enables generation of the Exception overhead counter overflow event" "Disabled,Enabled" bitfld.long 0x00 17. " CPIEVTENA ,Enables generation of the CPI counter overflow event" "Disabled,Enabled" bitfld.long 0x00 16. " EXCTRCENA ,Enables generation of exception trace" "Disabled,Enabled" newline bitfld.long 0x00 12. " PCSAMPLEENA ,Enables use of POSTCNT counter as a timer for Periodic PC sample packet generation" "Disabled,Enabled" bitfld.long 0x00 10.--11. " SYNCTAP ,Selects the position of the synchronization packet counter tap on the CYCCNT counter" "Disabled,CYCCNT[24],CYCCNT[26],CYCCNT[28]" bitfld.long 0x00 9. " CYCTAP ,Selects the position of the POSTCNT tap on the CYCCNT counter" "CYCCNT[6],CYCCNT[10]" newline bitfld.long 0x00 5.--8. " POSTINIT ,Initial value for the POSTCNT counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 1.--4. " POSTPRESET ,Reload value for the POSTCNT counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0. " CYCCNTENA ,Enables CYCCNT" "Disabled,Enabled" line.long 0x04 "DWT_CYCCNT,Cycle Count register" line.long 0x08 "DWT_CPICNT,CPI Count register" hexmask.long.byte 0x08 0.--7. 1. " CPICNT ,The base CPI counter" line.long 0x0c "DWT_EXCCNT,Exception Overhead Count Register" hexmask.long.byte 0x0c 0.--7. 1. " EXCCNT ,The exception overhead counter" line.long 0x10 "DWT_SLEEPCNT,Sleep Count Register" hexmask.long.byte 0x10 0.--7. 1. " SLEEPCNT ,Sleep Counter" line.long 0x14 "DWT_LSUCNT,LSU Count Register" hexmask.long.byte 0x14 0.--7. 1. " LSUCNT ,Load-store counter" line.long 0x18 "DWT_FOLDCNT,Folded-instruction Count register" hexmask.long.byte 0x18 0.--7. 1. " FOLDCNT ,Folded-instruction counter" rgroup.long 0x1C++0x03 line.long 0x00 "DWT_PCSR,Program Counter Sample register" newline group.long 0x20++0x07 line.long 0x00 "DWT_COMP0,DWT Comparator Register 0" line.long 0x04 "DWT_MASK0,DWT Mask Registers 0" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x1A0)==0x20) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x1A0)==0x00) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x180)==0x80) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet,UNPREDICTABLE,UNPREDICTABLE,Generate watchpoint debug event,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,CMPMATCH[N] event,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" else group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x30)++0x07 line.long 0x00 "DWT_COMP1,DWT Comparator Register 1" line.long 0x04 "DWT_MASK1,DWT Mask Registers 1" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x30+0x08))&0x120)==0x20) group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x30+0x08))&0x120)==0x00) group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x40)++0x07 line.long 0x00 "DWT_COMP2,DWT Comparator Register 2" line.long 0x04 "DWT_MASK2,DWT Mask Registers 2" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x40+0x08))&0x120)==0x20) group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x40+0x08))&0x120)==0x00) group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x50)++0x07 line.long 0x00 "DWT_COMP3,DWT Comparator Register 3" line.long 0x04 "DWT_MASK3,DWT Mask Registers 3" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x50+0x08))&0x120)==0x20) group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x50+0x08))&0x120)==0x00) group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" newline bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" newline textfld " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif width 6. tree "CoreSight Identification Registers" rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0c "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0c "CID3,Component ID3" tree.end width 0x0B else newline textline "DWT component base address not specified" newline endif tree.end tree.end AUTOINDENT.POP tree.end endif sif (CORENAME()=="CORTEXM4F") tree.close "Core Registers (Cortex-M4F)" AUTOINDENT.PUSH AUTOINDENT.OFF tree "System Control" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 12. group.long 0x08++0x03 line.long 0x00 "ACTLR,Auxiliary Control Register" bitfld.long 0x00 9. " DISFPCA ,Disables lazy stacking of floating point context" "No,Yes" bitfld.long 0x00 8. " DISOOFP ,Disables floating point instructions completing" "No,Yes" bitfld.long 0x00 2. " DISFOLD ,Disables folding of IT instructions" "No,Yes" textline " " bitfld.long 0x00 1. " DISDEFWBUF ,Disables write buffer use during default memory map accesses" "No,Yes" bitfld.long 0x00 0. " DISMCYCINT ,Disables interruption of multi-cycle instructions" "No,Yes" group.long 0x10++0x0B line.long 0x00 "SYST_CSR,SysTick Control and Status Register" rbitfld.long 0x00 16. " COUNTFLAG ,Counter Flag" "Not counted,Counted" bitfld.long 0x00 2. " CLKSOURCE ,SysTick clock source" "External,Core" bitfld.long 0x00 1. " TICKINT ,SysTick Handler" "No SysTick,SysTick" textline " " bitfld.long 0x00 0. " ENABLE ,Counter Enable" "Disabled,Enabled" line.long 0x04 "SYST_RVR,SysTick Reload Value Register" hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,The value to load into the SYST_CVR when the counter reaches 0" line.long 0x08 "SYST_CVR,SysTick Current Value Register" rgroup.long 0x1C++0x03 line.long 0x00 "SYST_CALIB,SysTick Calibration Value Register" bitfld.long 0x00 31. " NOREF ,Indicates whether the implementation defined reference clock is implemented" "Implemented,Not implemented" bitfld.long 0x00 30. " SKEW ,Indicates whether the 10ms calibration value is exact" "Exact,Inexact" hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Holds a reload value to be used for 10ms (100Hz) timing" rgroup.long 0xD00++0x03 line.long 0x00 "CPUID,CPU ID Base Register" hexmask.long.byte 0x00 24.--31. 1. " IMPLEMENTER ,Implementer Code" bitfld.long 0x00 20.--23. " VARIANT ,Indicates processor revision" "Revision 0,?..." bitfld.long 0x00 16.--19. " ARCHITECTURE ,Architecture" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " hexmask.long.word 0x00 4.--15. 1. " PARTNO ,Indicates part number" bitfld.long 0x00 0.--3. " REVISION ,Indicates patch release" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" group.long 0xD04++0x23 line.long 0x00 "ICSR,Interrupt Control State Register" bitfld.long 0x00 31. " NMIPENDSET ,Set Pending NMI Bit" "Inactive,Active" bitfld.long 0x00 28. " PENDSVSET ,Set Pending pendSV Bit" "Not pending,Pending" bitfld.long 0x00 27. " PENDSVCLR ,Removes the pending status of the PendSV exception" "No effect,Removed" textline " " bitfld.long 0x00 26. " PENDSTSET ,Set Pending SysTick Bit" "Not pending,Pending" bitfld.long 0x00 25. " PENDSTCLR ,Clear Pending SysTick Bit" "No effect,Removed" bitfld.long 0x00 23. " ISRPREEMPT ,Use Only at Debug Time" "Not active,Active" textline " " bitfld.long 0x00 22. " ISRPENDING ,Indicates whether an external interrupt" "Not pending,Pending" hexmask.long.word 0x00 12.--20. 1. " VECTPENDING ,Pending ISR Number Field" bitfld.long 0x00 11. " RETTOBASE ,Interrupt Exception" "Active,Not active" textline " " hexmask.long.word 0x00 0.--8. 1. " VECTACTIVE ,The exception number of the current executing exception" line.long 0x04 "VTOR,Vector Table Offset Register" hexmask.long 0x04 7.--31. 0x80 " TBLOFF ,Vector table address" line.long 0x08 "AIRCR,Application Interrupt and Reset Control Register" hexmask.long.word 0x08 16.--31. 1. " VECTKEY ,Register Key" rbitfld.long 0x08 15. " ENDIANESS ,Data endianness Bit" "Little,Big" bitfld.long 0x08 8.--10. " PRIGROUP ,Interrupt Priority Grouping Field" "[7:1]/[0],[7:2]/[1:0],[7:3]/[2:0],[7:4]/[3:0],[7:5]/[4:0],[7:6]/[5:0],[7]/[6:0],-/[7:0]" textline " " bitfld.long 0x08 2. " SYSRESETREQ ,System Reset Request" "Not requested,Requested" bitfld.long 0x08 1. " VECTCLRACTIVE ,Clear Active Vector Bit" "No effect,Clear" bitfld.long 0x08 0. " VECTRESET ,System Reset" "No effect,Reset" line.long 0x0C "SCR,System Control Register" bitfld.long 0x0C 4. " SEVONPEND ,Determines whether an interrupt transition from inactive state to pending state is a wakeup event" "Not wakeup,Wakeup" bitfld.long 0x0C 2. " SLEEPDEEP ,Provides a qualifying hint indicating that waking from sleep might take longer" "Not deep sleep,Deep sleep" bitfld.long 0x0C 1. " SLEEPONEXIT ,Determines whether, on an exit from an ISR that returns to the base level of execution priority, the processor enters a sleep state" "Disabled,Enabled" line.long 0x10 "CCR,Configuration Control Register" bitfld.long 0x10 18. " BP ,Branch prediction enable bit" "Disabled,Enabled" bitfld.long 0x10 17. " IC ,Instruction cache enable bit" "Disabled,Enabled" bitfld.long 0x10 16. " DC ,Cache enable bit" "Disabled,Enabled" textline " " bitfld.long 0x10 9. " STKALIGN ,8-byte Stack Frame Alignment" "4-byte/no adjustment,8-byte/adjustment" bitfld.long 0x10 8. " BFHFNMIGN ,Enable NMI and Hard Fault and FAULTMASK to Ignore Bus Fault" "Disabled,Enabled" bitfld.long 0x10 4. " DIV_0_TRP ,Trap Divide by Zero" "Disabled,Enabled" textline " " bitfld.long 0x10 3. " UNALIGN_TRP ,Trap for Unaligned Access" "Disabled,Enabled" bitfld.long 0x10 1. " USERSETMPEND ,Controls whether unprivileged software can access the STIR" "Denied,Allowed" bitfld.long 0x10 0. " NONEBASETHRDENA ,Control Entry to Thread Mode" "Only from last exception,Any level" line.long 0x14 "SHPR1,SSystem Handler Priority Register 1" hexmask.long.byte 0x14 24.--31. 1. " PRI_7 ,Priority of System Handler 7" hexmask.long.byte 0x14 16.--23. 1. " PRI_6 ,Priority of system handler 6(UsageFault)" hexmask.long.byte 0x14 8.--15. 1. " PRI_5 ,Priority of system handler 5(BusFault)" textline " " hexmask.long.byte 0x14 0.--7. 1. " PRI_4 ,Priority of system handler 4(MemManage)" line.long 0x18 "SHPR2,System Handler Priority Register 2" hexmask.long.byte 0x18 24.--31. 1. " PRI_11 ,Priority of system handler 11(SVCall)" hexmask.long.byte 0x18 16.--23. 1. " PRI_10 ,Priority of System Handler 10" hexmask.long.byte 0x18 8.--15. 1. " PRI_9 ,Priority of System Handler 9" textline " " hexmask.long.byte 0x18 0.--7. 1. " PRI_8 ,Priority of System Handler 8" line.long 0x1C "SHPR3,System Handler Priority Register 3" hexmask.long.byte 0x1C 24.--31. 1. " PRI_15 ,Priority of System Handler 15(SysTick)" hexmask.long.byte 0x1C 16.--23. 1. " PRI_14 ,Priority of System Handler 14(PendSV)" hexmask.long.byte 0x1C 8.--15. 1. " PRI_13 ,Priority of System Handler 13" textline " " hexmask.long.byte 0x1C 0.--7. 1. " PRI_12 ,Priority of System Handler 12(DebugMonitor)" line.long 0x20 "SHCSR,System Handler Control and State Register" bitfld.long 0x20 18. " USGFAULTENA ,Enable UsageFault" "Disabled,Enabled" bitfld.long 0x20 17. " BUSFAULTENA ,Enable BusFault" "Disabled,Enabled" bitfld.long 0x20 16. " MEMFAULTENA ,Enable MemManage fault" "Disabled,Enabled" textline " " bitfld.long 0x20 15. " SVCALLPENDED ,SVCall is pending" "Not pending,Pending" bitfld.long 0x20 14. " BUSFAULTPENDED ,BusFault is pending" "Not pending,Pending" bitfld.long 0x20 13. " MEMFAULTPENDED ,MemManage is pending" "Not pending,Pending" textline " " bitfld.long 0x20 12. " USGFAULTPENDED ,UsageFault is pending" "Not pending,Pending" bitfld.long 0x20 11. " SYSTICKACT ,SysTick is Active" "Not active,Active" bitfld.long 0x20 10. " PENDSVACT ,PendSV is Active" "Not active,Active" textline " " bitfld.long 0x20 8. " MONITORACT ,Monitor is Active" "Not active,Active" bitfld.long 0x20 7. " SVCALLACT ,SVCall is Active" "Not active,Active" bitfld.long 0x20 3. " USGFAULTACT ,UsageFault is Active" "Not active,Active" textline " " bitfld.long 0x20 1. " BUSFAULTACT ,BusFault is Active" "Not active,Active" bitfld.long 0x20 0. " MEMFAULTACT ,MemManage is Active" "Not active,Active" group.byte 0xD28++0x1 line.byte 0x00 "MMFSR,MemManage Status Register" bitfld.byte 0x00 7. " MMARVALID ,Address Valid Flag" "Not valid,Valid" bitfld.byte 0x00 5. " MLSPERR ,A MemManage fault occurred during FP lazy state preservation" "Not occurred,Occurred" bitfld.byte 0x00 4. " MSTKERR ,tacking Access Violations" "Not occurred,Occurred" textline " " bitfld.byte 0x00 3. " MUNSTKERR ,Unstack Access Violations" "Not occurred,Occurred" bitfld.byte 0x00 1. " DACCVIOL ,Data Access Violation" "Not occurred,Occurred" bitfld.byte 0x00 0. " IACCVIOL ,Instruction Access Violation" "Not occurred,Occurred" line.byte 0x01 "BFSR,Bus Fault Status Register" bitfld.byte 0x01 7. " BFARVALID ,Address Valid Flag" "Not valid,Valid" bitfld.byte 0x01 5. " LSPERR ,A bus fault occurred during FP lazy state preservation" "Not occurred,Occurred" bitfld.byte 0x01 4. " STKERR ,Derived bus fault(exception entry)" "Not occurred,Occurred" textline " " bitfld.byte 0x01 3. " UNSTKERR ,Derived bus fault(exception return)" "Not occurred,Occurred" bitfld.byte 0x01 2. " IMPRECISERR ,Imprecise data access error" "Not occurred,Occurred" bitfld.byte 0x01 1. " PRECISERR ,Precise data access error" "Not occurred,Occurred" textline " " bitfld.byte 0x01 0. " IBUSERR ,Bus fault on an instruction prefetch" "Not occurred,Occurred" group.word 0xD2A++0x1 line.word 0x00 "USAFAULT,Usage Fault Status Register" bitfld.word 0x00 9. " DIVBYZERO ,Divide by zero error" "No error,Error" bitfld.word 0x00 8. " UNALIGNED ,Unaligned access error" "No error,Error" bitfld.word 0x00 3. " NOCP ,A coprocessor access error" "No error,Error" textline " " bitfld.word 0x00 2. " INVPC ,An integrity check error" "No error,Error" bitfld.word 0x00 1. " INVSTATE ,Invalid Combination of EPSR and Instruction" "No error,Error" bitfld.word 0x00 0. " UNDEFINSTR ,Undefined instruction error" "No error,Error" group.long 0xD2C++0x07 line.long 0x00 "HFSR,Hard Fault Status Register" bitfld.long 0x00 31. " DEBUGEVT ,Indicates when a Debug event has occurred" "Not occurred,Occurred" bitfld.long 0x00 30. " FORCED ,Indicates that a fault with configurable priority" "Not occurred,Occurred" bitfld.long 0x00 1. " VECTTBL ,Indicates when a fault has occurred because of a vector table read error on exception processing" "Not occurred,Occurred" line.long 0x04 "DFSR,Debug Fault Status Register" bitfld.long 0x04 4. " EXTERNAL ,Indicates a debug event generated because of the assertion of EDBGRQ" "Not asserted,Asserted" bitfld.long 0x04 3. " VCATCH ,Vector Catch Flag" "Not occurred,Occurred" bitfld.long 0x04 2. " DWTTRAP ,Indicates a debug event generated by the DWT" "Not occurred,Occurred" textline " " bitfld.long 0x04 1. " BKPT ,BKPT Flag" "Not executed,Executed" bitfld.long 0x04 0. " HALTED ,Indicates a debug event generated by either" "Not requested,Requested" group.long 0xD34++0x0B line.long 0x00 "MMFAR,MemManage Fault Address Register" line.long 0x04 "BFAR,BusFault Address Register" line.long 0x08 "AFSR,Auxiliary Fault Status Register" group.long 0xD88++0x03 line.long 0x00 "CPACR,Coprocessor Access Control Register" bitfld.long 0x00 22.--23. " CP11 ,Access privileges for coprocessor 11" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 20.--21. " CP10 ,Access privileges for coprocessor 10" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 14.--15. " CP7 ,Access privileges for coprocessor 7" "Access denied,Privileged only,Reserved,Full access" textline " " bitfld.long 0x00 12.--13. " CP6 ,Access privileges for coprocessor 6" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 10.--11. " CP5 ,Access privileges for coprocessor 5" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 8.--9. " CP4 ,Access privileges for coprocessor 4" "Access denied,Privileged only,Reserved,Full access" textline " " bitfld.long 0x00 6.--7. " CP3 ,Access privileges for coprocessor 3" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 4.--5. " CP2 ,Access privileges for coprocessor 2" "Access denied,Privileged only,Reserved,Full access" bitfld.long 0x00 2.--3. " CP1 ,Access privileges for coprocessor 1" "Access denied,Privileged only,Reserved,Full access" textline " " bitfld.long 0x00 0.--1. " CP0 ,Access privileges for coprocessor 0" "Access denied,Privileged only,Reserved,Full access" wgroup.long 0xF00++0x03 line.long 0x00 "STIR,Software Trigger Interrupt Register" hexmask.long.word 0x00 0.--8. 1. " INTID ,Indicates the interrupt to be triggered" width 10. tree "Feature Registers" rgroup.long 0xD40++0x0B line.long 0x00 "ID_PFR0,Processor Feature Register 0" bitfld.long 0x00 4.--7. " STATE1 ,Thumb instruction set support" ",,,Supported,?..." bitfld.long 0x00 0.--3. " STATE0 ,ARM instruction set support" "Not supported,?..." line.long 0x04 "ID_PFR1,Processor Feature Register 1" bitfld.long 0x04 8.--11. " MPROF ,M profile programmers' model" ",,2-stack,?..." line.long 0x08 "ID_DFR0,Debug Feature Register 0" bitfld.long 0x08 20.--23. " DBGMOD ,Support for memory-mapped debug model for M profile processors" "Not supported,Supported,?..." hgroup.long 0xD4C++0x03 hide.long 0x00 "ID_AFR0,Auxiliary Feature Register 0" rgroup.long 0xD50++0x03 line.long 0x00 "ID_MMFR0,Memory Model Feature Register 0" bitfld.long 0x00 20.--23. " AUXREG ,Indicates the support for Auxiliary registers" "Not supported,ACTLR only,?..." bitfld.long 0x00 16.--19. " TCMSUP ,Indicates the support for Tightly Coupled Memory (TCM)" "Not supported,Supported,?..." bitfld.long 0x00 12.--15. " SHRLEV ,Indicates the number of shareability levels implemented" "Level 1,?..." textline " " bitfld.long 0x00 8.--11. " OUTMSHR ,Indicates the outermost shareability domain implemented" "Non-cacheable,,,,,,,,,,,,,,,Ignored" bitfld.long 0x00 4.--7. " PMSASUP ,Indicates support for a PMSA" "Not supported,,,PMSAv7,?..." hgroup.long 0xD54++0x03 hide.long 0x00 "ID_MMFR1,Memory Model Feature Register 1" rgroup.long 0xD58++0x03 line.long 0x00 "ID_MMFR2,Memory Model Feature Register 2" bitfld.long 0x00 24.--27. " WFISTALL ,Indicates the support for Wait For Interrupt (WFI) stalling" "Not supported,Supported,?..." rgroup.long 0xD60++0x13 line.long 0x00 "ID_ISAR0,Instruction Set Attributes Register 0" bitfld.long 0x00 24.--27. " DIVIDE ,Indicates the supported divide instructions" "Not supported,SDIV/UDIV,?..." bitfld.long 0x00 20.--23. " DEBUG ,Indicates the supported debug instructions" "Not supported,BKPT,?..." bitfld.long 0x00 16.--19. " COPROC ,Indicates the supported coprocessor instructions" "Not supported,CDP/LDC/MCR/STC,CDP2/LDC2/MCR2/STC2,MCRR/MRRC,MCRR2/MRRC2,?..." textline " " bitfld.long 0x00 12.--15. " CMPBRANCH ,Indicates the supported combined compare and branch instructions" "Not supported,CBNZ/CBZ,?..." bitfld.long 0x00 8.--11. " BITFIELD ,Indicates the supported bitfield instructions" "Not supported,BFC/BFI/SBFX/UBFX,?..." bitfld.long 0x00 4.--7. " BITCOUNT ,Indicates the supported bit counting instructions" "Not supported,CLZ,?..." line.long 0x04 "ID_ISAR1,Instruction Set Attributes Register 1" bitfld.long 0x04 24.--27. " INTERWORK ,Indicates the supported Interworking instructions" "Not supported,BX,BX/BLX,?..." bitfld.long 0x04 20.--23. " IMMEDIATE ,Indicates the support for data-processing instructions with long immediates" "Not supported,ADDW/MOVW/MOVT/SUBW,?..." bitfld.long 0x04 16.--19. " IFTHEN ,Indicates the supported IfThen instructions" "Not supported,IT,?..." textline " " bitfld.long 0x04 12.--15. " EXTEND ,Indicates the supported Extend instructions" "Not supported,Supported,Supported,?..." line.long 0x08 "ID_ISAR2,Instruction Set Attributes Register 2" bitfld.long 0x08 24.--27. " REVERSAL ,Indicates the supported reversal instructions" "Not supported,REV/REV16/REVSH,REV/REV16/REVSH/RBIT,?..." bitfld.long 0x08 20.--23. " MULTU ,Indicates the supported advanced unsigned multiply instructions" "Not supported,UMULL/UMLAL,UMULL/UMLAL/UMAAL,?..." bitfld.long 0x08 16.--19. " MULTS ,Indicates the supported advanced signed multiply instructions" "Not supported,Supported,Supported,Supported,?..." textline " " bitfld.long 0x08 12.--15. " MULT ,Indicates the supported additional multiply instructions" "Not supported,MLA,MLA/MLS,?..." bitfld.long 0x08 8.--11. " MULTIACCESSINT ,Indicates the support for multi-access interruptible instructions" "Not supported,LDM/STM restartable,LDM/STM continuable,?..." bitfld.long 0x08 4.--7. " MEMHINT ,Indicates the supported memory hint instructions" "Not supported,,,PLD/PLI,?..." textline " " bitfld.long 0x08 0.--3. " LOADSTORE ,Indicates the supported additional load and store instructions" "Not supported,LDRD/STRD,?..." line.long 0x0C "ID_ISAR3,Instruction Set Attributes Register 3" bitfld.long 0x0C 24.--27. " TRUENOP ,Indicates the support for a true NOP instruction" "Not supported,Supported,?..." bitfld.long 0x0C 20.--23. " THUMBCOPY ,Indicates the supported non flag-setting MOV instructions" "Not supported,Supported,?..." bitfld.long 0x0C 16.--19. " TABBRANCH ,Indicates the supported Table Branch instructions" "Not supported,TBB/TBH,?..." textline " " bitfld.long 0x0C 12.--15. " SYNCHPRIM ,Indicates the supported Table Branch instructions" "Not supported,Supported,Supported,Supported,?..." bitfld.long 0x0C 8.--11. " SVC ,Indicates the supported SVC instructions" "Not supported,SVC,?..." bitfld.long 0x0C 4.--7. " SIMD ,Indicates the supported SIMD instructions" "Not supported,Supported,,Supported,?..." textline " " bitfld.long 0x0C 0.--3. " SATURATE ,Indicates the supported Saturate instructions" "Not supported,QADD/QDADD/QDSUB/QSUB,?..." line.long 0x10 "ID_ISAR4,Instruction Set Attributes Register 4" bitfld.long 0x10 24.--27. " PSR_M ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,?..." bitfld.long 0x10 20.--23. " SYNCHPRIMFRAC ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,Supported,Supported,?..." bitfld.long 0x10 16.--19. " BARRIER ,Indicates the supported Barrier instructions" "Not supported,DMB/DSB/ISB,?..." textline " " bitfld.long 0x10 8.--11. " WRITEBACK ,Indicates the support for writeback addressing modes" "Basic support,Full support,?..." bitfld.long 0x10 4.--7. " WITHSHIFTS ,Indicates the support for instructions with shifts" "MOV/shift,Shift LSL 0-3,,Shift other,?..." bitfld.long 0x10 0.--3. " UNPRIV ,Indicates the supported unprivileged instructions" "Not supported,LDRBT/LDRT/STRBT/STRT,LDRBT/LDRT/STRBT/STRT/LDRHT/LDRSBT/LDRSHTSTRHT,?..." tree.end width 6. tree "CoreSight Identification Registers" rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0C "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0C "CID3,Component ID3" tree.end width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Memory Protection Unit" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 15. rgroup.long 0xD90++0x03 line.long 0x00 "MPU_TYPE,MPU Type Register" bitfld.long 0x00 16.--23. " IREGION ,Instruction region" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..." bitfld.long 0x00 8.--15. " DREGION ,Number of regions supported by the MPU" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..." bitfld.long 0x00 0. " SEPARATE ,Indicates support for separate instruction and data address maps" "Not supported,Supported" group.long 0xD94++0x03 line.long 0x00 "MPU_CTRL,MPU Control Register" bitfld.long 0x00 2. " PRIVDEFENA ,Enables the default memory map as a background region for privileged access" "Disabled,Enabled" bitfld.long 0x00 1. " HFNMIENA ,Handlers executing with priority less than 0 access memory with the MPU enabled or with the MPU disabled" "MPU disabled,MPU enabled" bitfld.long 0x00 0. " ENABLE ,Enables the MPU" "Disabled,Enabled" group.long 0xD98++0x03 line.long 0x00 "MPU_RNR,MPU Region Number Register" hexmask.long.byte 0x00 0.--7. 1. " REGION ,Indicates the memory region accessed by MPU_RBAR and MPU_RASR" tree.close "MPU regions" if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x0 group.long 0xD9C++0x03 "Region 0" saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 0 (not implemented)" saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x1 group.long 0xD9C++0x03 "Region 1" saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 1 (not implemented)" saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x2 group.long 0xD9C++0x03 "Region 2" saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 2 (not implemented)" saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x3 group.long 0xD9C++0x03 "Region 3" saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 3 (not implemented)" saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x4 group.long 0xD9C++0x03 "Region 4" saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 4 (not implemented)" saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x5 group.long 0xD9C++0x03 "Region 5" saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 5 (not implemented)" saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x6 group.long 0xD9C++0x03 "Region 6" saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 6 (not implemented)" saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x7 group.long 0xD9C++0x03 "Region 7" saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 7 (not implemented)" saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x8 group.long 0xD9C++0x03 "Region 8" saveout 0xD98 %l 0x8 line.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x8 line.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 8 (not implemented)" saveout 0xD98 %l 0x8 hide.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x8 hide.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x9 group.long 0xD9C++0x03 "Region 9" saveout 0xD98 %l 0x9 line.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x9 line.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 9 (not implemented)" saveout 0xD98 %l 0x9 hide.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x9 hide.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xA group.long 0xD9C++0x03 "Region 10" saveout 0xD98 %l 0xA line.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xA line.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 10 (not implemented)" saveout 0xD98 %l 0xA hide.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xA hide.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xB group.long 0xD9C++0x03 "Region 11" saveout 0xD98 %l 0xB line.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xB line.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 11 (not implemented)" saveout 0xD98 %l 0xB hide.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xB hide.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xC group.long 0xD9C++0x03 "Region 12" saveout 0xD98 %l 0xC line.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xC line.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 12 (not implemented)" saveout 0xD98 %l 0xC hide.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xC hide.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xD group.long 0xD9C++0x03 "Region 13" saveout 0xD98 %l 0xD line.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xD line.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 13 (not implemented)" saveout 0xD98 %l 0xD hide.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xD hide.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xE group.long 0xD9C++0x03 "Region 14" saveout 0xD98 %l 0xE line.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xE line.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 14 (not implemented)" saveout 0xD98 %l 0xE hide.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xE hide.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xF group.long 0xD9C++0x03 "Region 15" saveout 0xD98 %l 0xF line.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15" hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0xF line.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 15 (not implemented)" saveout 0xD98 %l 0xF hide.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0xF hide.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15" textline " " textline " " endif tree.end width 0x0b else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Nested Vectored Interrupt Controller" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 6. rgroup.long 0x04++0x03 line.long 0x00 "ICTR,Interrupt Controller Type Register" bitfld.long 0x00 0.--3. " INTLINESNUM ,Total Number of Interrupt" "0-32,33-64,65-96,97-128,129-160,161-192,193-224,225-240,?..." tree "Interrupt Enable Registers" width 23. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x100++0x03 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x100++0x7 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x100++0x0B line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x100++0x0F line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x100++0x13 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x100++0x17 line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x100++0x1B line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x100++0x1F line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" line.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register" setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " ENA239 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " ENA238 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " ENA237 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " ENA236 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " ENA235 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " ENA234 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " ENA233 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " ENA232 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " ENA231 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " ENA230 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " ENA229 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " ENA228 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " ENA227 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " ENA226 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " ENA225 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " ENA224 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" else hgroup.long 0x100++0x1F hide.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register" hide.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register" hide.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register" hide.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register" hide.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register" hide.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register" hide.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register" hide.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register" endif tree.end tree "Interrupt Pending Registers" width 23. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x200++0x03 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x200++0x07 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x200++0x0B line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x200++0x0F line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x200++0x13 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x200++0x17 line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x200++0x1B line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x200++0x1F line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending" line.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register" setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " PEN239 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " PEN238 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " PEN237 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " PEN236 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " PEN235 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " PEN234 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " PEN233 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " PEN232 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " PEN231 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " PEN230 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " PEN229 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " PEN228 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " PEN227 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " PEN226 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " PEN225 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " PEN224 ,Interrupt Set/Clear Pending" "Not pending,Pending" else hgroup.long 0x200++0x1F hide.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register" hide.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register" endif tree.end tree "Interrupt Active Bit Registers" width 9. if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) rgroup.long 0x300++0x03 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) rgroup.long 0x300++0x07 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) rgroup.long 0x300++0x0B line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) rgroup.long 0x300++0x0F line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) rgroup.long 0x300++0x13 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) rgroup.long 0x300++0x17 line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) rgroup.long 0x300++0x1B line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" line.long 0x18 "ACTIVE7,Active Bit Register 7" bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) rgroup.long 0x300++0x1F line.long 0x00 "ACTIVE1,Active Bit Register 1" bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active" line.long 0x04 "ACTIVE2,Active Bit Register 2" bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active" line.long 0x08 "ACTIVE3,Active Bit Register 3" bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active" line.long 0x0c "ACTIVE4,Active Bit Register 4" bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active" line.long 0x10 "ACTIVE5,Active Bit Register 5" bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active" line.long 0x14 "ACTIVE6,Active Bit Register 6" bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active" line.long 0x18 "ACTIVE7,Active Bit Register 7" bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active" line.long 0x1c "ACTIVE8,Active Bit Register 8" bitfld.long 0x1c 15. " ACTIVE239 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 14. " ACTIVE238 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 13. " ACTIVE237 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 12. " ACTIVE236 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 11. " ACTIVE235 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 10. " ACTIVE234 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x1c 9. " ACTIVE233 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 8. " ACTIVE232 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 7. " ACTIVE231 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 6. " ACTIVE230 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 5. " ACTIVE229 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 4. " ACTIVE228 ,Interrupt Active Flag" "Not active,Active" textline " " bitfld.long 0x1c 3. " ACTIVE227 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 2. " ACTIVE226 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 1. " ACTIVE225 ,Interrupt Active Flag" "Not active,Active" bitfld.long 0x1c 0. " ACTIVE224 ,Interrupt Active Flag" "Not active,Active" else hgroup.long 0x300++0x1F hide.long 0x00 "ACTIVE1,Active Bit Register 1" hide.long 0x04 "ACTIVE2,Active Bit Register 2" hide.long 0x08 "ACTIVE3,Active Bit Register 3" hide.long 0x0c "ACTIVE4,Active Bit Register 4" hide.long 0x10 "ACTIVE5,Active Bit Register 5" hide.long 0x14 "ACTIVE6,Active Bit Register 6" hide.long 0x18 "ACTIVE7,Active Bit Register 7" hide.long 0x1c "ACTIVE8,Active Bit Register 8" endif tree.end tree "Interrupt Priority Registers" if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00) group.long 0x400++0x1F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01) group.long 0x400++0x3F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02) group.long 0x400++0x5F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03) group.long 0x400++0x7F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04) group.long 0x400++0x9F line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05) group.long 0x400++0xBF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06) group.long 0x400++0xDF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" line.long 0xC0 "IPR48,Interrupt Priority Register" hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority" hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority" hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority" hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority" line.long 0xC4 "IPR49,Interrupt Priority Register" hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority" hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority" hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority" hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority" line.long 0xC8 "IPR50,Interrupt Priority Register" hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority" hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority" hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority" hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority" line.long 0xCC "IPR51,Interrupt Priority Register" hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority" hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority" hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority" hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority" line.long 0xD0 "IPR52,Interrupt Priority Register" hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority" hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority" hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority" hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority" line.long 0xD4 "IPR53,Interrupt Priority Register" hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority" hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority" hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority" hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority" line.long 0xD8 "IPR54,Interrupt Priority Register" hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority" hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority" hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority" hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority" line.long 0xDC "IPR55,Interrupt Priority Register" hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority" hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority" hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority" hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07) group.long 0x400++0xEF line.long 0x0 "IPR0,Interrupt Priority Register" hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority" hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority" hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority" hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority" line.long 0x4 "IPR1,Interrupt Priority Register" hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority" hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority" hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority" hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority" line.long 0x8 "IPR2,Interrupt Priority Register" hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority" hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority" hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority" hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority" line.long 0xC "IPR3,Interrupt Priority Register" hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority" hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority" hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority" hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority" line.long 0x10 "IPR4,Interrupt Priority Register" hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority" hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority" hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority" hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority" line.long 0x14 "IPR5,Interrupt Priority Register" hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority" hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority" hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority" hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority" line.long 0x18 "IPR6,Interrupt Priority Register" hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority" hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority" hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority" hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority" line.long 0x1C "IPR7,Interrupt Priority Register" hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority" hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority" hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority" hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority" line.long 0x20 "IPR8,Interrupt Priority Register" hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority" hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority" hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority" hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority" line.long 0x24 "IPR9,Interrupt Priority Register" hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority" hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority" hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority" hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority" line.long 0x28 "IPR10,Interrupt Priority Register" hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority" hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority" hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority" hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority" line.long 0x2C "IPR11,Interrupt Priority Register" hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority" hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority" hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority" hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority" line.long 0x30 "IPR12,Interrupt Priority Register" hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority" hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority" hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority" hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority" line.long 0x34 "IPR13,Interrupt Priority Register" hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority" hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority" hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority" hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority" line.long 0x38 "IPR14,Interrupt Priority Register" hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority" hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority" hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority" hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority" line.long 0x3C "IPR15,Interrupt Priority Register" hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority" hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority" hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority" hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority" line.long 0x40 "IPR16,Interrupt Priority Register" hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority" hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority" hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority" hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority" line.long 0x44 "IPR17,Interrupt Priority Register" hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority" hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority" hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority" hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority" line.long 0x48 "IPR18,Interrupt Priority Register" hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority" hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority" hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority" hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority" line.long 0x4C "IPR19,Interrupt Priority Register" hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority" hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority" hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority" hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority" line.long 0x50 "IPR20,Interrupt Priority Register" hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority" hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority" hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority" hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority" line.long 0x54 "IPR21,Interrupt Priority Register" hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority" hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority" hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority" hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority" line.long 0x58 "IPR22,Interrupt Priority Register" hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority" hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority" hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority" hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority" line.long 0x5C "IPR23,Interrupt Priority Register" hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority" hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority" hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority" hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority" line.long 0x60 "IPR24,Interrupt Priority Register" hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority" hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority" hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority" hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority" line.long 0x64 "IPR25,Interrupt Priority Register" hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority" hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority" hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority" hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority" line.long 0x68 "IPR26,Interrupt Priority Register" hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority" hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority" hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority" hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority" line.long 0x6C "IPR27,Interrupt Priority Register" hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority" hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority" hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority" hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority" line.long 0x70 "IPR28,Interrupt Priority Register" hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority" hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority" hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority" hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority" line.long 0x74 "IPR29,Interrupt Priority Register" hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority" hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority" hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority" hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority" line.long 0x78 "IPR30,Interrupt Priority Register" hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority" hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority" hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority" hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority" line.long 0x7C "IPR31,Interrupt Priority Register" hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority" hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority" hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority" hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority" line.long 0x80 "IPR32,Interrupt Priority Register" hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority" hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority" hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority" hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority" line.long 0x84 "IPR33,Interrupt Priority Register" hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority" hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority" hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority" hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority" line.long 0x88 "IPR34,Interrupt Priority Register" hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority" hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority" hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority" hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority" line.long 0x8C "IPR35,Interrupt Priority Register" hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority" hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority" hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority" hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority" line.long 0x90 "IPR36,Interrupt Priority Register" hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority" hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority" hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority" hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority" line.long 0x94 "IPR37,Interrupt Priority Register" hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority" hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority" hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority" hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority" line.long 0x98 "IPR38,Interrupt Priority Register" hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority" hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority" hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority" hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority" line.long 0x9C "IPR39,Interrupt Priority Register" hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority" hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority" hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority" hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority" line.long 0xA0 "IPR40,Interrupt Priority Register" hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority" hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority" hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority" hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority" line.long 0xA4 "IPR41,Interrupt Priority Register" hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority" hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority" hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority" hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority" line.long 0xA8 "IPR42,Interrupt Priority Register" hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority" hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority" hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority" hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority" line.long 0xAC "IPR43,Interrupt Priority Register" hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority" hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority" hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority" hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority" line.long 0xB0 "IPR44,Interrupt Priority Register" hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority" hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority" hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority" hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority" line.long 0xB4 "IPR45,Interrupt Priority Register" hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority" hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority" hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority" hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority" line.long 0xB8 "IPR46,Interrupt Priority Register" hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority" hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority" hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority" hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority" line.long 0xBC "IPR47,Interrupt Priority Register" hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority" hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority" hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority" hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority" line.long 0xC0 "IPR48,Interrupt Priority Register" hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority" hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority" hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority" hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority" line.long 0xC4 "IPR49,Interrupt Priority Register" hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority" hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority" hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority" hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority" line.long 0xC8 "IPR50,Interrupt Priority Register" hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority" hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority" hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority" hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority" line.long 0xCC "IPR51,Interrupt Priority Register" hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority" hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority" hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority" hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority" line.long 0xD0 "IPR52,Interrupt Priority Register" hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority" hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority" hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority" hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority" line.long 0xD4 "IPR53,Interrupt Priority Register" hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority" hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority" hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority" hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority" line.long 0xD8 "IPR54,Interrupt Priority Register" hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority" hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority" hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority" hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority" line.long 0xDC "IPR55,Interrupt Priority Register" hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority" hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority" hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority" hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority" line.long 0xE0 "IPR56,Interrupt Priority Register" hexmask.long.byte 0xE0 24.--31. 1. " PRI_227 ,Interrupt 227 Priority" hexmask.long.byte 0xE0 16.--23. 1. " PRI_226 ,Interrupt 226 Priority" hexmask.long.byte 0xE0 8.--15. 1. " PRI_225 ,Interrupt 225 Priority" hexmask.long.byte 0xE0 0.--7. 1. " PRI_224 ,Interrupt 224 Priority" line.long 0xE4 "IPR57,Interrupt Priority Register" hexmask.long.byte 0xE4 24.--31. 1. " PRI_231 ,Interrupt 231 Priority" hexmask.long.byte 0xE4 16.--23. 1. " PRI_230 ,Interrupt 230 Priority" hexmask.long.byte 0xE4 8.--15. 1. " PRI_229 ,Interrupt 229 Priority" hexmask.long.byte 0xE4 0.--7. 1. " PRI_228 ,Interrupt 228 Priority" line.long 0xE8 "IPR58,Interrupt Priority Register" hexmask.long.byte 0xE8 24.--31. 1. " PRI_235 ,Interrupt 235 Priority" hexmask.long.byte 0xE8 16.--23. 1. " PRI_234 ,Interrupt 234 Priority" hexmask.long.byte 0xE8 8.--15. 1. " PRI_233 ,Interrupt 233 Priority" hexmask.long.byte 0xE8 0.--7. 1. " PRI_232 ,Interrupt 232 Priority" line.long 0xEC "IPR59,Interrupt Priority Register" hexmask.long.byte 0xEC 24.--31. 1. " PRI_239 ,Interrupt 239 Priority" hexmask.long.byte 0xEC 16.--23. 1. " PRI_238 ,Interrupt 238 Priority" hexmask.long.byte 0xEC 8.--15. 1. " PRI_237 ,Interrupt 237 Priority" hexmask.long.byte 0xEC 0.--7. 1. " PRI_236 ,Interrupt 236 Priority" else hgroup.long 0x400++0xEF hide.long 0x0 "IPR0,Interrupt Priority Register" hide.long 0x4 "IPR1,Interrupt Priority Register" hide.long 0x8 "IPR2,Interrupt Priority Register" hide.long 0xC "IPR3,Interrupt Priority Register" hide.long 0x10 "IPR4,Interrupt Priority Register" hide.long 0x14 "IPR5,Interrupt Priority Register" hide.long 0x18 "IPR6,Interrupt Priority Register" hide.long 0x1C "IPR7,Interrupt Priority Register" hide.long 0x20 "IPR8,Interrupt Priority Register" hide.long 0x24 "IPR9,Interrupt Priority Register" hide.long 0x28 "IPR10,Interrupt Priority Register" hide.long 0x2C "IPR11,Interrupt Priority Register" hide.long 0x30 "IPR12,Interrupt Priority Register" hide.long 0x34 "IPR13,Interrupt Priority Register" hide.long 0x38 "IPR14,Interrupt Priority Register" hide.long 0x3C "IPR15,Interrupt Priority Register" hide.long 0x40 "IPR16,Interrupt Priority Register" hide.long 0x44 "IPR17,Interrupt Priority Register" hide.long 0x48 "IPR18,Interrupt Priority Register" hide.long 0x4C "IPR19,Interrupt Priority Register" hide.long 0x50 "IPR20,Interrupt Priority Register" hide.long 0x54 "IPR21,Interrupt Priority Register" hide.long 0x58 "IPR22,Interrupt Priority Register" hide.long 0x5C "IPR23,Interrupt Priority Register" hide.long 0x60 "IPR24,Interrupt Priority Register" hide.long 0x64 "IPR25,Interrupt Priority Register" hide.long 0x68 "IPR26,Interrupt Priority Register" hide.long 0x6C "IPR27,Interrupt Priority Register" hide.long 0x70 "IPR28,Interrupt Priority Register" hide.long 0x74 "IPR29,Interrupt Priority Register" hide.long 0x78 "IPR30,Interrupt Priority Register" hide.long 0x7C "IPR31,Interrupt Priority Register" hide.long 0x80 "IPR32,Interrupt Priority Register" hide.long 0x84 "IPR33,Interrupt Priority Register" hide.long 0x88 "IPR34,Interrupt Priority Register" hide.long 0x8C "IPR35,Interrupt Priority Register" hide.long 0x90 "IPR36,Interrupt Priority Register" hide.long 0x94 "IPR37,Interrupt Priority Register" hide.long 0x98 "IPR38,Interrupt Priority Register" hide.long 0x9C "IPR39,Interrupt Priority Register" hide.long 0xA0 "IPR40,Interrupt Priority Register" hide.long 0xA4 "IPR41,Interrupt Priority Register" hide.long 0xA8 "IPR42,Interrupt Priority Register" hide.long 0xAC "IPR43,Interrupt Priority Register" hide.long 0xB0 "IPR44,Interrupt Priority Register" hide.long 0xB4 "IPR45,Interrupt Priority Register" hide.long 0xB8 "IPR46,Interrupt Priority Register" hide.long 0xBC "IPR47,Interrupt Priority Register" hide.long 0xC0 "IPR48,Interrupt Priority Register" hide.long 0xC4 "IPR49,Interrupt Priority Register" hide.long 0xC8 "IPR50,Interrupt Priority Register" hide.long 0xCC "IPR51,Interrupt Priority Register" hide.long 0xD0 "IPR52,Interrupt Priority Register" hide.long 0xD4 "IPR53,Interrupt Priority Register" hide.long 0xD8 "IPR54,Interrupt Priority Register" hide.long 0xDC "IPR55,Interrupt Priority Register" hide.long 0xE0 "IPR56,Interrupt Priority Register" hide.long 0xE4 "IPR57,Interrupt Priority Register" hide.long 0xE8 "IPR58,Interrupt Priority Register" hide.long 0xEC "IPR59,Interrupt Priority Register" endif tree.end width 0x0b else newline textline "COREDEBUG component base address not specified" newline endif tree.end sif CORENAME()=="CORTEXM4F" tree "Floating-point Unit (FPU)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 8. group.long 0xF34++0x0B line.long 0x00 "FPCCR,Floating-Point Context Control Register" bitfld.long 0x00 31. " ASPEN ,Execution of a floating-point instruction sets the CONTROL.FPCA bit to 1" "Disabled,Enabled" bitfld.long 0x00 30. " LSPEN ,Enables lazy context save of FP state" "Disabled,Enabled" bitfld.long 0x00 8. " MONRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the DebugMonitor exception to pending" "Not able,Able" textline " " bitfld.long 0x00 6. " BFRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the BusFault exception to pending" "Not able,Able" bitfld.long 0x00 5. " MMRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the MemManage exception to pending" "Not able,Able" bitfld.long 0x00 4. " HFRDY ,Indicates whether the software executing when the processor allocated the FP stack frame was able to set the HardFault exception to pending" "Not able,Able" textline " " bitfld.long 0x00 3. " THREAD ,Indicates the processor mode when it allocated the FP stack frame" "Handler,Thread" bitfld.long 0x00 1. " USER ,Indicates the privilege level of the software executing" "Privileged,Unprivileged" bitfld.long 0x00 0. " LSPACT ,Indicates whether Lazy preservation of the FP state is active" "Not active,Active" line.long 0x04 "FPCAR,Floating-Point Context Address Register" hexmask.long 0x04 3.--31. 0x8 " ADDRESS ,The location of the unpopulated floating-point register space allocated on an exception stack frame" line.long 0x08 "FPDSCR,Floating-Point Default Status Control Register" bitfld.long 0x08 26. " AHP ,Default value for FPSCR.AHP" "IEEE 754-2008,Alternative" bitfld.long 0x08 25. " DN ,Default value for FPSCR.DN" "NaN operands,Any operation" bitfld.long 0x08 24. " FZ ,Default value for FPSCR.FZ" "No Flush mode,Flush mode" textline " " bitfld.long 0x08 22.--23. " RMODE ,Default value for FPSCR.RMode" "Round to Nearest,Round towards Plus Infinity,Round towards Minus Infinity,Round towards Zero" rgroup.long 0xF40++0x07 line.long 0x00 "MVFR0,Media and FP Feature Register 0" bitfld.long 0x00 28.--31. " FPRNDMOD ,Indicates the rounding modes supported by the FP floating-point hardware" ",All supported,?..." bitfld.long 0x00 24.--27. " SRTERR ,Indicates the hardware support for FP short vectors" "Not supported,?..." bitfld.long 0x00 20.--23. " SQRROOT ,Indicates the hardware support for FP square root operations" ",Supported,?..." textline " " bitfld.long 0x00 16.--19. " DIV ,Indicates the hardware support for FP divide operations" ",Supported,?..." bitfld.long 0x00 12.--15. " FPEXTRP ,Indicates whether the FP hardware implementation supports exception trapping" "Not supported,?..." bitfld.long 0x00 8.--11. " DBLPREC ,Indicates the hardware support for FP double_precision operations" "Not supported,,Supported,?..." textline " " bitfld.long 0x00 4.--7. " SNGLPREC ,Indicates the hardware support for FP single-precision operations" ",,Supported,?..." bitfld.long 0x00 0.--3. " A_SIMD ,Indicates the size of the FP register bank" ",Supported-16x64-bit,?..." line.long 0x04 "MVFR1,Media and FP Feature Register 1" bitfld.long 0x04 28.--31. " FP_FUSED_MAC ,Indicates whether the FP supports fused multiply accumulate operations" ",Supported,?..." bitfld.long 0x04 24.--27. " FP_HPFP ,Indicates whether the FP supports half-precision and double-precision floating-point conversion instructions" ",Half-single,Half-single and half-double,?..." textline " " bitfld.long 0x04 4.--7. " D_NAN ,Indicates whether the FP hardware implementation supports only the Default NaN mode" ",NaN propagation,?..." bitfld.long 0x04 0.--3. " FTZ_MODE ,Indicates whether the FP hardware implementation supports only the Flush-to-Zero mode of operation" ",Full denorm. num. arit.,?..." width 0xB else newline textline "COREDEBUG component base address not specified" newline endif tree.end endif tree "Debug" tree "Core Debug" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 7. group.long 0xD30++0x03 line.long 0x00 "DFSR,Debug Fault Status Register" eventfld.long 0x00 4. " EXTERNAL ,Indicates a debug event generated because of the assertion of an external debug request" "Not generated,Generated" eventfld.long 0x00 3. " VCATCH ,Indicates triggering of a Vector catch" "Not triggered,Triggered" eventfld.long 0x00 2. " DWTTRAP ,Indicates a debug event generated by the DWT" "Not generated,Generated" newline eventfld.long 0x00 1. " BKPT ,Indicates a debug event generated by BKPT instruction execution or a breakpoint match in FPB" "Not generated,Generated" eventfld.long 0x00 0. " HALTED ,Indicates a debug event generated by either a C_HALT or C_STEP request, triggered by a write to the DHCSR or a step request triggered by setting DEMCR.MON_STEP to 1" "Not generated,Generated" newline hgroup.long 0xDF0++0x03 hide.long 0x00 "DHCSR,Debug Halting Control and Status Register" in newline wgroup.long 0xDF4++0x03 line.long 0x00 "DCRSR,Debug Core Register Selector Register" bitfld.long 0x00 16. " REGWNR ,Register Read/Write" "Read,Write" hexmask.long.byte 0x00 0.--6. 1. " REGSEL ,Specifies the ARM core register or special-purpose register or Floating-point extension register" group.long 0xDF8++0x03 line.long 0x00 "DCRDR,Debug Core Register Data Register" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDFC))&0x10000)==0x10000) group.long 0xDFC++0x03 line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register" bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled" bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1" bitfld.long 0x00 18. " MON_STEP ,Setting this bit to 1 makes the step request pending" "No step,Step" newline bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending" bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled" bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled" newline bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap" "Disabled,Enabled" bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled" bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled" newline bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled" bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled" bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled" newline bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled" else group.long 0xDFC++0x03 line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register" bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled" bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1" newline bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending" bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled" bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled" newline bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap" "Disabled,Enabled" bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled" bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled" newline bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled" bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled" bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled" newline bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled" endif width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Flash Patch and Breakpoint Unit (FPB)" sif COMPonent.AVAILABLE("FPB") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1)) width 10. group.long 0x00++0x07 line.long 0x00 "FP_CTRL,Flash Patch Control Register" bitfld.long 0x00 28.--31. " REV ,Flash Patch Breakpoint architecture revision" "Version 1,Version 2,?..." rbitfld.long 0x00 4.--7. 12.--14. " NUM_CODE ,The number of instruction address comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127" bitfld.long 0x00 1. " KEY ,Key Field" "Low,High" bitfld.long 0x00 0. " ENABLE ,Flash Patch Unit Enable" "Disabled,Enabled" textline "" line.long 0x04 "FP_REMAP,Flash Patch Remap Register" bitfld.long 0x04 29. " RMPSPT ,Indicates whether the FPB unit supports flash patch remap" "Not supported,SRAM region" hexmask.long.tbyte 0x04 5.--28. 0x20 " REMAP ,Remap Base Address Field" if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x8))&0x01)==0x00) group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x8++0x03 line.long 0x00 "FP_COMP0,Flash Patch Comparator Register 0" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0xC))&0x01)==0x00) group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0xC++0x03 line.long 0x00 "FP_COMP1,Flash Patch Comparator Register 1" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x10))&0x01)==0x00) group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x10++0x03 line.long 0x00 "FP_COMP2,Flash Patch Comparator Register 2" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x14))&0x01)==0x00) group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x14++0x03 line.long 0x00 "FP_COMP3,Flash Patch Comparator Register 3" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x18))&0x01)==0x00) group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x18++0x03 line.long 0x00 "FP_COMP4,Flash Patch Comparator Register 4" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x1C))&0x01)==0x00) group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x1C++0x03 line.long 0x00 "FP_COMP5,Flash Patch Comparator Register 5" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x20))&0x01)==0x00) group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x20++0x03 line.long 0x00 "FP_COMP6,Flash Patch Comparator Register 6" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x00) group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" bitfld.long 0x00 30.--31. " REPLACE ,Defines the behaviour when the COMP address is matched" ",Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both" hexmask.long 0x00 2.--28. 0x04 " COMP ,Comparison Address" bitfld.long 0x00 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled" elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))))&0x10000000)==0x10000000) if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))+0x24))&0x01)==0x00) group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" else group.long 0x24++0x03 line.long 0x00 "FP_COMP7,Flash Patch Comparator Register 7" hexmask.long 0x00 1.--31. 0x02 " BPADDR ,Breakpoint address" bitfld.long 0x00 0. " BE ,Enable bit for Breakpoint" "Disabled,Enabled" endif endif width 6. tree "CoreSight Identification Registers" rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0c "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0c "CID3,Component ID3" tree.end width 0xB else newline textline "FPB component base address not specified" newline endif tree.end tree "Data Watchpoint and Trace Unit (DWT)" sif COMPonent.AVAILABLE("DWT") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1)) width 15. group.long 0x00++0x1B line.long 0x00 "DWT_CTRL,Control Register" rbitfld.long 0x00 28.--31. " NUMCOMP ,Number of comparators implemented" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rbitfld.long 0x00 27. " NOTRCPKT ,Shows whether the implementation supports trace sampling and exception tracing" "Supported,Not supported" rbitfld.long 0x00 26. " NOEXTTRIG ,Shows whether the implementation includes external match signals" "Supported,Not supported" textline " " rbitfld.long 0x00 25. " NOCYCCNT ,Shows whether the implementation supports a cycle counter" "Supported,Not supported" rbitfld.long 0x00 24. " NOPRFCNT ,Shows whether the implementation supports the profiling counters" "Supported,Not supported" bitfld.long 0x00 22. " CYCEVTENA ,Enables POSTCNT underflow Event counter packets generation" "Disabled,Enabled" textline " " bitfld.long 0x00 21. " FOLDEVTENA ,Enables generation of the Folded-instruction counter overflow event" "Disabled,Enabled" bitfld.long 0x00 20. " LSUEVTENA ,Enables generation of the LSU counter overflow event" "Disabled,Enabled" bitfld.long 0x00 19. " SLEEPEVTENA ,Enables generation of the Sleep counter overflow event" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " EXCEVTENA ,Enables generation of the Exception overhead counter overflow event" "Disabled,Enabled" bitfld.long 0x00 17. " CPIEVTENA ,Enables generation of the CPI counter overflow event" "Disabled,Enabled" bitfld.long 0x00 16. " EXCTRCENA ,Enables generation of exception trace" "Disabled,Enabled" textline " " bitfld.long 0x00 12. " PCSAMPLEENA ,Enables use of POSTCNT counter as a timer for Periodic PC sample packet generation" "Disabled,Enabled" bitfld.long 0x00 10.--11. " SYNCTAP ,Selects the position of the synchronization packet counter tap on the CYCCNT counter" "Disabled,CYCCNT[24],CYCCNT[26],CYCCNT[28]" bitfld.long 0x00 9. " CYCTAP ,Selects the position of the POSTCNT tap on the CYCCNT counter" "CYCCNT[6],CYCCNT[10]" textline " " bitfld.long 0x00 5.--8. " POSTINIT ,Initial value for the POSTCNT counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 1.--4. " POSTPRESET ,Reload value for the POSTCNT counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 0. " CYCCNTENA ,Enables CYCCNT" "Disabled,Enabled" line.long 0x04 "DWT_CYCCNT,Cycle Count Register" line.long 0x08 "DWT_CPICNT,CPI Count Register" hexmask.long.byte 0x08 0.--7. 1. " CPICNT ,The base CPI counter" line.long 0x0c "DWT_EXCCNT,Exception Overhead Count Register" hexmask.long.byte 0x0c 0.--7. 1. " EXCCNT ,The exception overhead counter" line.long 0x10 "DWT_SLEEPCNT,Sleep Count Register" hexmask.long.byte 0x10 0.--7. 1. " SLEEPCNT ,Sleep Counter" line.long 0x14 "DWT_LSUCNT,LSU Count Register" hexmask.long.byte 0x14 0.--7. 1. " LSUCNT ,Load-store counter" line.long 0x18 "DWT_FOLDCNT,Folded-instruction Count Register" hexmask.long.byte 0x18 0.--7. 1. " FOLDCNT ,Folded-instruction counter" rgroup.long 0x1C++0x03 line.long 0x00 "DWT_PCSR,Program Counter Sample register" textline " " group.long 0x20++0x07 line.long 0x00 "DWT_COMP0,DWT Comparator Register 0" line.long 0x04 "DWT_MASK0,DWT Mask Registers 0" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x1A0)==0x20) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x1A0)==0x00) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x180)==0x80) group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet,UNPREDICTABLE,UNPREDICTABLE,Generate watchpoint debug event,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,CMPMATCH[N] event,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" else group.long 0x28++0x03 line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " CYCMATCH ,Enable cycle count comparison for comparator 0" "Disabled,Enabled" bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x30)++0x07 line.long 0x00 "DWT_COMP1,DWT Comparator Register 1" line.long 0x04 "DWT_MASK1,DWT Mask Registers 1" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x30+0x08))&0x120)==0x20) group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x30+0x08))&0x120)==0x00) group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x30+0x08)++0x03 line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x40)++0x07 line.long 0x00 "DWT_COMP2,DWT Comparator Register 2" line.long 0x04 "DWT_MASK2,DWT Mask Registers 2" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x40+0x08))&0x120)==0x20) group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x40+0x08))&0x120)==0x00) group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x40+0x08)++0x03 line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif group.long (0x50)++0x07 line.long 0x00 "DWT_COMP3,DWT Comparator Register 3" line.long 0x04 "DWT_MASK3,DWT Mask Registers 3" bitfld.long 0x04 0.--4. " MASK ,The size of the ignore mask" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31" if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x50+0x08))&0x120)==0x20) group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send address trace packet on READ/WRITE,Send data value + address packet on READ/WRITE,Send data value + address packet on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data address trace packet on READ,Send data address trace packet on WRITE,Send data address + PC value on READ,Send data address + PC value on WRITE" elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x50+0x08))&0x120)==0x00) group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,Send PC value trace packet on READ/WRITE,Send data value trace packet on READ/WRITE,Send data value + PC value on READ/WRITE,Watchpoint debug event on PC match,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,CMPMATCH[N] event on PC match,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ/WRITE,Send data value trace packet on READ,Send data value trace packet on WRITE,Send data value + PC value on READ,Send data value + PC value on WRITE" else group.long (0x50+0x08)++0x03 line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3" bitfld.long 0x00 24. " MATCHED ,Comparator match" "No matched,Matched" bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" textline " " bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "8-bit,16-bit,32-bit,Reserved" bitfld.long 0x00 9. " LNK1ENA ,Supports use of a second linked comparator" "Not Supported,Supported" bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " EMITRANGE ,Enables generation of Data trace address offset packets" "Disabled,Enabled" bitfld.long 0x00 0.--3. " FUNCTION ,Selects action taken on comparator match" "Disabled,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,Watchpoint debug event on READ,Watchpoint debug event on WRITE,Watchpoint debug event on READ/WRITE,UNPREDICTABLE,CMPMATCH[N] event on READ,CMPMATCH[N] event on WRITE,CMPMATCH[N] event on READ,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE,UNPREDICTABLE" endif width 6. tree "CoreSight Identification Registers" rgroup.long 0xFE0++0x0F line.long 0x00 "PID0,Peripheral ID0" hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]" line.long 0x04 "PID1,Peripheral ID1" hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]" hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]" line.long 0x08 "PID2,Peripheral ID2" hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision" bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC" hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]" line.long 0x0c "PID3,Peripheral ID3" hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field" hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block" rgroup.long 0xFD0++0x03 line.long 0x00 "PID4,Peripheral Identification Register 4" hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count" hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code" rgroup.long 0xFF0++0x0F line.long 0x00 "CID0,Component ID0 (Preamble)" line.long 0x04 "CID1,Component ID1" hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class" hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble" line.long 0x08 "CID2,Component ID2" line.long 0x0c "CID3,Component ID3" tree.end width 0x0B else newline textline "DWT component base address not specified" newline endif tree.end tree.end AUTOINDENT.POP tree.end endif tree "ADC" base ad:0x0 tree "LPADC1" base ad:0x40050000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline bitfld.long 0x0 10. "CALOFSI,Calibration Offset Function Implemented" "0: Offset calibration and offset trimming not..,1: Offset calibration and offset trimming.." bitfld.long 0x0 9. "IADCKI,Internal LPADC Clock implemented" "0: Internal clock source not implemented.,1: Internal clock source (and CFG[ADCKEN]).." newline bitfld.long 0x0 8. "VR1RNGI,Voltage Reference 1 Range Control Bit Implemented" "0: Range control not required. CFG[VREF1RNG] is not..,1: Range control required. CFG[VREF1RNG] is.." bitfld.long 0x0 4.--6. "CSW,Channel Scale Width" "0: Channel scaling not supported.,1: Channel scaling supported. 1-bit CSCALE control..,?,?,?,?,6: Channel scaling supported. 6-bit CSCALE control..,?" newline bitfld.long 0x0 3. "MVI,Multi Vref Implemented" "0: Single voltage reference input supported.,1: Multiple voltage reference inputs supported." bitfld.long 0x0 1. "DIFFEN,Differential Supported" "0: Differential operation not supported.,1: Differential operation supported. CMDLa[DIFF].." newline bitfld.long 0x0 0. "RES,Resolution" "0: Up to 13-bit differential/12-bit single ended..,1: Up to 16-bit differential/15-bit single ended.." line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 24.--31. 1. "CMD_NUM,Command Buffer Number" hexmask.long.byte 0x4 16.--23. 1. "CV_NUM,Compare Value Number" newline hexmask.long.byte 0x4 8.--15. 1. "FIFOSIZE,Result FIFO Depth" hexmask.long.byte 0x4 0.--7. 1. "TRIG_NUM,Trigger Number" group.long 0x10++0x17 line.long 0x0 "CTRL,LPADC Control Register" bitfld.long 0x0 8. "RSTFIFO,Reset FIFO" "0: No effect.,1: FIFO is reset." bitfld.long 0x0 3.--4. "TRIG_SRC,Hardware trigger source selection" "0: ADC_ETC hw trigger and HW trigger are enabled,1: ADC_ETC hw trigger is enabled,2: HW trigger is enabled,?" newline bitfld.long 0x0 2. "DOZEN,Doze Enable" "0: LPADC is enabled in Doze mode.,1: LPADC is disabled in Doze mode." bitfld.long 0x0 1. "RST,Software Reset" "0: LPADC logic is not reset.,1: LPADC logic is reset." newline bitfld.long 0x0 0. "ADCEN,LPADC Enable" "0: LPADC is disabled.,1: LPADC is enabled." line.long 0x4 "STAT,LPADC Status Register" hexmask.long.byte 0x4 24.--27. 1. "CMDACT,Command Active" rbitfld.long 0x4 16.--18. "TRGACT,Trigger Active" "0: Command (sequence) associated with Trigger 0..,1: Command (sequence) associated with Trigger 1..,2: Command (sequence) associated with Trigger 2..,3: Command (sequence) from the associated Trigger..,4: Command (sequence) from the associated Trigger..,5: Command (sequence) from the associated Trigger..,6: Command (sequence) from the associated Trigger..,7: Command (sequence) from the associated Trigger.." newline rbitfld.long 0x4 8. "ADC_ACTIVE,ADC Active" "0: The LPADC is IDLE. There are no pending triggers..,1: The LPADC is processing a conversion running.." eventfld.long 0x4 1. "FOF,Result FIFO Overflow Flag" "0: No result FIFO overflow has occurred since the..,1: At least one result FIFO overflow has occurred.." newline rbitfld.long 0x4 0. "RDY,Result FIFO Ready Flag" "0: Result FIFO data level not above watermark level.,1: Result FIFO holding data above watermark level." line.long 0x8 "IE,Interrupt Enable Register" bitfld.long 0x8 1. "FOFIE,Result FIFO Overflow Interrupt Enable" "0: FIFO overflow interrupts are not enabled.,1: FIFO overflow interrupts are enabled." bitfld.long 0x8 0. "FWMIE,FIFO Watermark Interrupt Enable" "0: FIFO watermark interrupts are not enabled.,1: FIFO watermark interrupts are enabled." line.long 0xC "DE,DMA Enable Register" bitfld.long 0xC 0. "FWMDE,FIFO Watermark DMA Enable" "0: DMA request disabled.,1: DMA request enabled." line.long 0x10 "CFG,LPADC Configuration Register" bitfld.long 0x10 28. "PWREN,LPADC Analog Pre-Enable" "0: LPADC analog circuits are only enabled while..,1: LPADC analog circuits are pre-enabled and ready.." hexmask.long.byte 0x10 16.--23. 1. "PUDLY,Power Up Delay" newline bitfld.long 0x10 6.--7. "REFSEL,Voltage Reference Selection" "0: (Default) Option 1 setting.,1: Option 2 setting.,2: Option 3 setting.,?" bitfld.long 0x10 4.--5. "PWRSEL,Power Configuration Select" "0: Level 1 (Lowest power setting),1: Level 2,2: Level 3,3: Level 4 (Highest power setting)" newline bitfld.long 0x10 0. "TPRICTRL,LPADC trigger priority control" "0: If a higher priority trigger is detected during..,1: If a higher priority trigger is received during.." line.long 0x14 "PAUSE,LPADC Pause Register" bitfld.long 0x14 31. "PAUSEEN,PAUSE Option Enable" "0: Pause operation disabled,1: Pause operation enabled" hexmask.long.word 0x14 0.--8. 1. "PAUSEDLY,Pause Delay" group.long 0x30++0x7 line.long 0x0 "FCTRL,LPADC FIFO Control Register" hexmask.long.byte 0x0 16.--19. 1. "FWMARK,Watermark level selection" hexmask.long.byte 0x0 0.--4. 1. "FCOUNT,Result FIFO counter" line.long 0x4 "SWTRIG,Software Trigger Register" bitfld.long 0x4 7. "SWT7,Software trigger 7 event" "0: No trigger 7 event generated.,1: Trigger 7 event generated." bitfld.long 0x4 6. "SWT6,Software trigger 6 event" "0: No trigger 6 event generated.,1: Trigger 6 event generated." newline bitfld.long 0x4 5. "SWT5,Software trigger 5 event" "0: No trigger 5 event generated.,1: Trigger 5 event generated." bitfld.long 0x4 4. "SWT4,Software trigger 4 event" "0: No trigger 4 event generated.,1: Trigger 4 event generated." newline bitfld.long 0x4 3. "SWT3,Software trigger 3 event" "0: No trigger 3 event generated.,1: Trigger 3 event generated." bitfld.long 0x4 2. "SWT2,Software trigger 2 event" "0: No trigger 2 event generated.,1: Trigger 2 event generated." newline bitfld.long 0x4 1. "SWT1,Software trigger 1 event" "0: No trigger 1 event generated.,1: Trigger 1 event generated." bitfld.long 0x4 0. "SWT0,Software trigger 0 event" "0: No trigger 0 event generated.,1: Trigger 0 event generated." repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xC0)++0x3 line.long 0x0 "TCTRL[$1],Trigger Control Register" hexmask.long.byte 0x0 24.--27. 1. "TCMD,Trigger command select" hexmask.long.byte 0x0 16.--19. 1. "TDLY,Trigger delay select" newline bitfld.long 0x0 8.--10. "TPRI,Trigger priority setting" "0: Set to highest priority Level 1,1: Set to corresponding priority level,2: Set to corresponding priority level,3: Set to corresponding priority level,4: Set to corresponding priority level,5: Set to corresponding priority level,6: Set to corresponding priority level,7: Set to lowest priority Level 8" bitfld.long 0x0 1. "CMD_SEL,The command number is selected by software TCMD or hardware tcmd signal" "0: TCTRLa[TCMD] will determine the command,1: Software TCDM is bypassed and hardware TCMD from.." newline bitfld.long 0x0 0. "HTEN,Trigger enable" "0: Hardware trigger source disabled,1: Hardware trigger source enabled" repeat.end group.long 0x100++0x77 line.long 0x0 "CMDL1,LPADC Command Low Buffer Register" bitfld.long 0x0 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x0 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x0 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x0 0.--4. 1. "ADCH,Input channel select" line.long 0x4 "CMDH1,LPADC Command High Buffer Register" hexmask.long.byte 0x4 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x4 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x4 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x4 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x4 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x4 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x8 "CMDL2,LPADC Command Low Buffer Register" bitfld.long 0x8 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x8 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x8 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x8 0.--4. 1. "ADCH,Input channel select" line.long 0xC "CMDH2,LPADC Command High Buffer Register" hexmask.long.byte 0xC 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0xC 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0xC 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0xC 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0xC 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0xC 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x10 "CMDL3,LPADC Command Low Buffer Register" bitfld.long 0x10 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x10 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x10 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x10 0.--4. 1. "ADCH,Input channel select" line.long 0x14 "CMDH3,LPADC Command High Buffer Register" hexmask.long.byte 0x14 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x14 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x14 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x14 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x14 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x14 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x18 "CMDL4,LPADC Command Low Buffer Register" bitfld.long 0x18 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x18 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x18 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x18 0.--4. 1. "ADCH,Input channel select" line.long 0x1C "CMDH4,LPADC Command High Buffer Register" hexmask.long.byte 0x1C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x1C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x1C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x1C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x1C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x1C 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x20 "CMDL5,LPADC Command Low Buffer Register" bitfld.long 0x20 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x20 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x20 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x20 0.--4. 1. "ADCH,Input channel select" line.long 0x24 "CMDH5,LPADC Command High Buffer Register" hexmask.long.byte 0x24 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x24 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x24 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x24 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x24 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x28 "CMDL6,LPADC Command Low Buffer Register" bitfld.long 0x28 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x28 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x28 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x28 0.--4. 1. "ADCH,Input channel select" line.long 0x2C "CMDH6,LPADC Command High Buffer Register" hexmask.long.byte 0x2C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x2C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x2C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x2C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x2C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x30 "CMDL7,LPADC Command Low Buffer Register" bitfld.long 0x30 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x30 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x30 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x30 0.--4. 1. "ADCH,Input channel select" line.long 0x34 "CMDH7,LPADC Command High Buffer Register" hexmask.long.byte 0x34 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x34 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x34 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x34 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x34 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x38 "CMDL8,LPADC Command Low Buffer Register" bitfld.long 0x38 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x38 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x38 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x38 0.--4. 1. "ADCH,Input channel select" line.long 0x3C "CMDH8,LPADC Command High Buffer Register" hexmask.long.byte 0x3C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x3C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x3C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x3C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x3C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x40 "CMDL9,LPADC Command Low Buffer Register" bitfld.long 0x40 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x40 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x40 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x40 0.--4. 1. "ADCH,Input channel select" line.long 0x44 "CMDH9,LPADC Command High Buffer Register" hexmask.long.byte 0x44 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x44 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x44 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x44 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x44 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x48 "CMDL10,LPADC Command Low Buffer Register" bitfld.long 0x48 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x48 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x48 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x48 0.--4. 1. "ADCH,Input channel select" line.long 0x4C "CMDH10,LPADC Command High Buffer Register" hexmask.long.byte 0x4C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x4C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x4C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x4C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x4C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x50 "CMDL11,LPADC Command Low Buffer Register" bitfld.long 0x50 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x50 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x50 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x50 0.--4. 1. "ADCH,Input channel select" line.long 0x54 "CMDH11,LPADC Command High Buffer Register" hexmask.long.byte 0x54 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x54 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x54 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x54 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x54 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x58 "CMDL12,LPADC Command Low Buffer Register" bitfld.long 0x58 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x58 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x58 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x58 0.--4. 1. "ADCH,Input channel select" line.long 0x5C "CMDH12,LPADC Command High Buffer Register" hexmask.long.byte 0x5C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x5C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x5C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x5C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x5C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x60 "CMDL13,LPADC Command Low Buffer Register" bitfld.long 0x60 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x60 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x60 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x60 0.--4. 1. "ADCH,Input channel select" line.long 0x64 "CMDH13,LPADC Command High Buffer Register" hexmask.long.byte 0x64 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x64 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x64 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x64 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x64 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x68 "CMDL14,LPADC Command Low Buffer Register" bitfld.long 0x68 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x68 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x68 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x68 0.--4. 1. "ADCH,Input channel select" line.long 0x6C "CMDH14,LPADC Command High Buffer Register" hexmask.long.byte 0x6C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x6C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x6C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x6C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x6C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x70 "CMDL15,LPADC Command Low Buffer Register" bitfld.long 0x70 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x70 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x70 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x70 0.--4. 1. "ADCH,Input channel select" line.long 0x74 "CMDH15,LPADC Command High Buffer Register" hexmask.long.byte 0x74 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x74 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x74 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x74 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x74 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "CV$1,Compare Value Register" hexmask.long.word 0x0 16.--31. 1. "CVH,Compare Value High." hexmask.long.word 0x0 0.--15. 1. "CVL,Compare Value Low" repeat.end rgroup.long 0x300++0x3 line.long 0x0 "RESFIFO,LPADC Data Result FIFO Register" bitfld.long 0x0 31. "VALID,FIFO entry is valid" "0: FIFO is empty. Discard any read from RESFIFO.,1: FIFO record read from RESFIFO is valid." hexmask.long.byte 0x0 24.--27. 1. "CMDSRC,Command Buffer Source" newline hexmask.long.byte 0x0 20.--23. 1. "LOOPCNT,Loop count value" bitfld.long 0x0 16.--18. "TSRC,Trigger Source" "0: Trigger source 0 initiated this conversion.,1: Trigger source 1 initiated this conversion.,2: Corresponding trigger source initiated this..,3: Corresponding trigger source initiated this..,4: Corresponding trigger source initiated this..,5: Corresponding trigger source initiated this..,6: Corresponding trigger source initiated this..,7: Trigger source 7 initiated this conversion." newline hexmask.long.word 0x0 0.--15. 1. "D,Data result" tree.end tree "LPADC2" base ad:0x40054000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline bitfld.long 0x0 10. "CALOFSI,Calibration Offset Function Implemented" "0: Offset calibration and offset trimming not..,1: Offset calibration and offset trimming.." bitfld.long 0x0 9. "IADCKI,Internal LPADC Clock implemented" "0: Internal clock source not implemented.,1: Internal clock source (and CFG[ADCKEN]).." newline bitfld.long 0x0 8. "VR1RNGI,Voltage Reference 1 Range Control Bit Implemented" "0: Range control not required. CFG[VREF1RNG] is not..,1: Range control required. CFG[VREF1RNG] is.." bitfld.long 0x0 4.--6. "CSW,Channel Scale Width" "0: Channel scaling not supported.,1: Channel scaling supported. 1-bit CSCALE control..,?,?,?,?,6: Channel scaling supported. 6-bit CSCALE control..,?" newline bitfld.long 0x0 3. "MVI,Multi Vref Implemented" "0: Single voltage reference input supported.,1: Multiple voltage reference inputs supported." bitfld.long 0x0 1. "DIFFEN,Differential Supported" "0: Differential operation not supported.,1: Differential operation supported. CMDLa[DIFF].." newline bitfld.long 0x0 0. "RES,Resolution" "0: Up to 13-bit differential/12-bit single ended..,1: Up to 16-bit differential/15-bit single ended.." line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 24.--31. 1. "CMD_NUM,Command Buffer Number" hexmask.long.byte 0x4 16.--23. 1. "CV_NUM,Compare Value Number" newline hexmask.long.byte 0x4 8.--15. 1. "FIFOSIZE,Result FIFO Depth" hexmask.long.byte 0x4 0.--7. 1. "TRIG_NUM,Trigger Number" group.long 0x10++0x17 line.long 0x0 "CTRL,LPADC Control Register" bitfld.long 0x0 8. "RSTFIFO,Reset FIFO" "0: No effect.,1: FIFO is reset." bitfld.long 0x0 3.--4. "TRIG_SRC,Hardware trigger source selection" "0: ADC_ETC hw trigger and HW trigger are enabled,1: ADC_ETC hw trigger is enabled,2: HW trigger is enabled,?" newline bitfld.long 0x0 2. "DOZEN,Doze Enable" "0: LPADC is enabled in Doze mode.,1: LPADC is disabled in Doze mode." bitfld.long 0x0 1. "RST,Software Reset" "0: LPADC logic is not reset.,1: LPADC logic is reset." newline bitfld.long 0x0 0. "ADCEN,LPADC Enable" "0: LPADC is disabled.,1: LPADC is enabled." line.long 0x4 "STAT,LPADC Status Register" hexmask.long.byte 0x4 24.--27. 1. "CMDACT,Command Active" rbitfld.long 0x4 16.--18. "TRGACT,Trigger Active" "0: Command (sequence) associated with Trigger 0..,1: Command (sequence) associated with Trigger 1..,2: Command (sequence) associated with Trigger 2..,3: Command (sequence) from the associated Trigger..,4: Command (sequence) from the associated Trigger..,5: Command (sequence) from the associated Trigger..,6: Command (sequence) from the associated Trigger..,7: Command (sequence) from the associated Trigger.." newline rbitfld.long 0x4 8. "ADC_ACTIVE,ADC Active" "0: The LPADC is IDLE. There are no pending triggers..,1: The LPADC is processing a conversion running.." eventfld.long 0x4 1. "FOF,Result FIFO Overflow Flag" "0: No result FIFO overflow has occurred since the..,1: At least one result FIFO overflow has occurred.." newline rbitfld.long 0x4 0. "RDY,Result FIFO Ready Flag" "0: Result FIFO data level not above watermark level.,1: Result FIFO holding data above watermark level." line.long 0x8 "IE,Interrupt Enable Register" bitfld.long 0x8 1. "FOFIE,Result FIFO Overflow Interrupt Enable" "0: FIFO overflow interrupts are not enabled.,1: FIFO overflow interrupts are enabled." bitfld.long 0x8 0. "FWMIE,FIFO Watermark Interrupt Enable" "0: FIFO watermark interrupts are not enabled.,1: FIFO watermark interrupts are enabled." line.long 0xC "DE,DMA Enable Register" bitfld.long 0xC 0. "FWMDE,FIFO Watermark DMA Enable" "0: DMA request disabled.,1: DMA request enabled." line.long 0x10 "CFG,LPADC Configuration Register" bitfld.long 0x10 28. "PWREN,LPADC Analog Pre-Enable" "0: LPADC analog circuits are only enabled while..,1: LPADC analog circuits are pre-enabled and ready.." hexmask.long.byte 0x10 16.--23. 1. "PUDLY,Power Up Delay" newline bitfld.long 0x10 6.--7. "REFSEL,Voltage Reference Selection" "0: (Default) Option 1 setting.,1: Option 2 setting.,2: Option 3 setting.,?" bitfld.long 0x10 4.--5. "PWRSEL,Power Configuration Select" "0: Level 1 (Lowest power setting),1: Level 2,2: Level 3,3: Level 4 (Highest power setting)" newline bitfld.long 0x10 0. "TPRICTRL,LPADC trigger priority control" "0: If a higher priority trigger is detected during..,1: If a higher priority trigger is received during.." line.long 0x14 "PAUSE,LPADC Pause Register" bitfld.long 0x14 31. "PAUSEEN,PAUSE Option Enable" "0: Pause operation disabled,1: Pause operation enabled" hexmask.long.word 0x14 0.--8. 1. "PAUSEDLY,Pause Delay" group.long 0x30++0x7 line.long 0x0 "FCTRL,LPADC FIFO Control Register" hexmask.long.byte 0x0 16.--19. 1. "FWMARK,Watermark level selection" hexmask.long.byte 0x0 0.--4. 1. "FCOUNT,Result FIFO counter" line.long 0x4 "SWTRIG,Software Trigger Register" bitfld.long 0x4 7. "SWT7,Software trigger 7 event" "0: No trigger 7 event generated.,1: Trigger 7 event generated." bitfld.long 0x4 6. "SWT6,Software trigger 6 event" "0: No trigger 6 event generated.,1: Trigger 6 event generated." newline bitfld.long 0x4 5. "SWT5,Software trigger 5 event" "0: No trigger 5 event generated.,1: Trigger 5 event generated." bitfld.long 0x4 4. "SWT4,Software trigger 4 event" "0: No trigger 4 event generated.,1: Trigger 4 event generated." newline bitfld.long 0x4 3. "SWT3,Software trigger 3 event" "0: No trigger 3 event generated.,1: Trigger 3 event generated." bitfld.long 0x4 2. "SWT2,Software trigger 2 event" "0: No trigger 2 event generated.,1: Trigger 2 event generated." newline bitfld.long 0x4 1. "SWT1,Software trigger 1 event" "0: No trigger 1 event generated.,1: Trigger 1 event generated." bitfld.long 0x4 0. "SWT0,Software trigger 0 event" "0: No trigger 0 event generated.,1: Trigger 0 event generated." repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xC0)++0x3 line.long 0x0 "TCTRL[$1],Trigger Control Register" hexmask.long.byte 0x0 24.--27. 1. "TCMD,Trigger command select" hexmask.long.byte 0x0 16.--19. 1. "TDLY,Trigger delay select" newline bitfld.long 0x0 8.--10. "TPRI,Trigger priority setting" "0: Set to highest priority Level 1,1: Set to corresponding priority level,2: Set to corresponding priority level,3: Set to corresponding priority level,4: Set to corresponding priority level,5: Set to corresponding priority level,6: Set to corresponding priority level,7: Set to lowest priority Level 8" bitfld.long 0x0 1. "CMD_SEL,The command number is selected by software TCMD or hardware tcmd signal" "0: TCTRLa[TCMD] will determine the command,1: Software TCDM is bypassed and hardware TCMD from.." newline bitfld.long 0x0 0. "HTEN,Trigger enable" "0: Hardware trigger source disabled,1: Hardware trigger source enabled" repeat.end group.long 0x100++0x77 line.long 0x0 "CMDL1,LPADC Command Low Buffer Register" bitfld.long 0x0 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x0 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x0 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x0 0.--4. 1. "ADCH,Input channel select" line.long 0x4 "CMDH1,LPADC Command High Buffer Register" hexmask.long.byte 0x4 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x4 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x4 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x4 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x4 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x4 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x8 "CMDL2,LPADC Command Low Buffer Register" bitfld.long 0x8 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x8 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x8 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x8 0.--4. 1. "ADCH,Input channel select" line.long 0xC "CMDH2,LPADC Command High Buffer Register" hexmask.long.byte 0xC 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0xC 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0xC 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0xC 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0xC 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0xC 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x10 "CMDL3,LPADC Command Low Buffer Register" bitfld.long 0x10 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x10 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x10 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x10 0.--4. 1. "ADCH,Input channel select" line.long 0x14 "CMDH3,LPADC Command High Buffer Register" hexmask.long.byte 0x14 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x14 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x14 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x14 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x14 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x14 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x18 "CMDL4,LPADC Command Low Buffer Register" bitfld.long 0x18 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x18 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x18 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x18 0.--4. 1. "ADCH,Input channel select" line.long 0x1C "CMDH4,LPADC Command High Buffer Register" hexmask.long.byte 0x1C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x1C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x1C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x1C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x1C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" bitfld.long 0x1C 0.--1. "CMPEN,Compare Function Enable" "0: Compare disabled.,?,2: Compare enabled. Store on true.,3: Compare enabled. Repeat channel acquisition.." line.long 0x20 "CMDL5,LPADC Command Low Buffer Register" bitfld.long 0x20 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x20 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x20 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x20 0.--4. 1. "ADCH,Input channel select" line.long 0x24 "CMDH5,LPADC Command High Buffer Register" hexmask.long.byte 0x24 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x24 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x24 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x24 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x24 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x28 "CMDL6,LPADC Command Low Buffer Register" bitfld.long 0x28 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x28 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x28 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x28 0.--4. 1. "ADCH,Input channel select" line.long 0x2C "CMDH6,LPADC Command High Buffer Register" hexmask.long.byte 0x2C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x2C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x2C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x2C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x2C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x30 "CMDL7,LPADC Command Low Buffer Register" bitfld.long 0x30 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x30 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x30 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x30 0.--4. 1. "ADCH,Input channel select" line.long 0x34 "CMDH7,LPADC Command High Buffer Register" hexmask.long.byte 0x34 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x34 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x34 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x34 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x34 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x38 "CMDL8,LPADC Command Low Buffer Register" bitfld.long 0x38 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x38 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x38 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x38 0.--4. 1. "ADCH,Input channel select" line.long 0x3C "CMDH8,LPADC Command High Buffer Register" hexmask.long.byte 0x3C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x3C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x3C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x3C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x3C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x40 "CMDL9,LPADC Command Low Buffer Register" bitfld.long 0x40 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x40 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x40 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x40 0.--4. 1. "ADCH,Input channel select" line.long 0x44 "CMDH9,LPADC Command High Buffer Register" hexmask.long.byte 0x44 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x44 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x44 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x44 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x44 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x48 "CMDL10,LPADC Command Low Buffer Register" bitfld.long 0x48 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x48 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x48 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x48 0.--4. 1. "ADCH,Input channel select" line.long 0x4C "CMDH10,LPADC Command High Buffer Register" hexmask.long.byte 0x4C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x4C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x4C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x4C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x4C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x50 "CMDL11,LPADC Command Low Buffer Register" bitfld.long 0x50 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x50 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x50 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x50 0.--4. 1. "ADCH,Input channel select" line.long 0x54 "CMDH11,LPADC Command High Buffer Register" hexmask.long.byte 0x54 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x54 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x54 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x54 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x54 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x58 "CMDL12,LPADC Command Low Buffer Register" bitfld.long 0x58 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x58 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x58 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x58 0.--4. 1. "ADCH,Input channel select" line.long 0x5C "CMDH12,LPADC Command High Buffer Register" hexmask.long.byte 0x5C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x5C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x5C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x5C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x5C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x60 "CMDL13,LPADC Command Low Buffer Register" bitfld.long 0x60 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x60 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x60 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x60 0.--4. 1. "ADCH,Input channel select" line.long 0x64 "CMDH13,LPADC Command High Buffer Register" hexmask.long.byte 0x64 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x64 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x64 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x64 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x64 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x68 "CMDL14,LPADC Command Low Buffer Register" bitfld.long 0x68 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x68 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x68 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x68 0.--4. 1. "ADCH,Input channel select" line.long 0x6C "CMDH14,LPADC Command High Buffer Register" hexmask.long.byte 0x6C 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x6C 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x6C 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x6C 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x6C 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" line.long 0x70 "CMDL15,LPADC Command Low Buffer Register" bitfld.long 0x70 13. "CSCALE,Channel Scale" "0: Scale selected analog channel (Factor of 30/64),1: (Default) Full scale (Factor of 1)" bitfld.long 0x70 6. "DIFF,Differential Mode Enable" "0: Single-ended mode.,1: Differential mode." newline bitfld.long 0x70 5. "ABSEL,A-side vs. B-side Select" "0: When DIFF=0b0 the associated A-side channel is..,1: When DIFF=0b0 the associated B-side channel is.." hexmask.long.byte 0x70 0.--4. 1. "ADCH,Input channel select" line.long 0x74 "CMDH15,LPADC Command High Buffer Register" hexmask.long.byte 0x74 24.--27. 1. "NEXT,Next Command Select" hexmask.long.byte 0x74 16.--19. 1. "LOOP,Loop Count Select" newline bitfld.long 0x74 12.--14. "AVGS,Hardware Average Select" "0: Single conversion.,1: 2 conversions averaged.,2: 4 conversions averaged.,3: 8 conversions averaged.,4: 16 conversions averaged.,5: 32 conversions averaged.,6: 64 conversions averaged.,7: 128 conversions averaged." bitfld.long 0x74 8.--10. "STS,Sample Time Select" "0: Minimum sample time of 3 ADCK cycles.,1: 3 + 21 ADCK cycles; 5 ADCK cycles total sample..,2: 3 + 22 ADCK cycles; 7 ADCK cycles total sample..,3: 3 + 23 ADCK cycles; 11 ADCK cycles total sample..,4: 3 + 24 ADCK cycles; 19 ADCK cycles total sample..,5: 3 + 25 ADCK cycles; 35 ADCK cycles total sample..,6: 3 + 26 ADCK cycles; 67 ADCK cycles total sample..,7: 3 + 27 ADCK cycles; 131 ADCK cycles total sample.." newline bitfld.long 0x74 7. "LWI,Loop with Increment" "0: Auto channel increment disabled,1: Auto channel increment enabled" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "CV$1,Compare Value Register" hexmask.long.word 0x0 16.--31. 1. "CVH,Compare Value High." hexmask.long.word 0x0 0.--15. 1. "CVL,Compare Value Low" repeat.end rgroup.long 0x300++0x3 line.long 0x0 "RESFIFO,LPADC Data Result FIFO Register" bitfld.long 0x0 31. "VALID,FIFO entry is valid" "0: FIFO is empty. Discard any read from RESFIFO.,1: FIFO record read from RESFIFO is valid." hexmask.long.byte 0x0 24.--27. 1. "CMDSRC,Command Buffer Source" newline hexmask.long.byte 0x0 20.--23. 1. "LOOPCNT,Loop count value" bitfld.long 0x0 16.--18. "TSRC,Trigger Source" "0: Trigger source 0 initiated this conversion.,1: Trigger source 1 initiated this conversion.,2: Corresponding trigger source initiated this..,3: Corresponding trigger source initiated this..,4: Corresponding trigger source initiated this..,5: Corresponding trigger source initiated this..,6: Corresponding trigger source initiated this..,7: Trigger source 7 initiated this conversion." newline hexmask.long.word 0x0 0.--15. 1. "D,Data result" tree.end tree.end tree "ADC_ETC" base ad:0x40048000 group.long 0x0++0x27 line.long 0x0 "CTRL,ADC_ETC Global Control Register" bitfld.long 0x0 31. "SOFTRST,Software synchronous reset active high." "0: ADC_ETC works normally.,1: All registers inside ADC_ETC will be reset to.." newline bitfld.long 0x0 29. "DMA_MODE_SEL,Select the trigger type of the DMA_REQ." "0: Trig DMA_REQ with latched signal REQ will be..,1: Trig DMA_REQ with pulsed signal REQ will be.." newline hexmask.long.byte 0x0 16.--23. 1. "PRE_DIVIDER,Pre-divider for trig delay and interval" newline hexmask.long.byte 0x0 0.--7. 1. "TRIG_ENABLE,TRIG enable register." line.long 0x4 "DONE0_1_IRQ,ETC DONE0 and DONE1 IRQ State Register" eventfld.long 0x4 23. "TRIG7_DONE1,TRIG7 done1 interrupt detection." "0: No TRIG7_DONE1 interrupt detected,1: TRIG7_DONE1 interrupt detected" newline eventfld.long 0x4 22. "TRIG6_DONE1,TRIG6 done1 interrupt detection." "0: No TRIG6_DONE1 interrupt detected,1: TRIG6_DONE1 interrupt detected" newline eventfld.long 0x4 21. "TRIG5_DONE1,TRIG5 done1 interrupt detection." "0: No TRIG5_DONE1 interrupt detected,1: TRIG5_DONE1 interrupt detected" newline eventfld.long 0x4 20. "TRIG4_DONE1,TRIG4 done1 interrupt detection." "0: No TRIG4_DONE1 interrupt detected,1: TRIG4_DONE1 interrupt detected" newline eventfld.long 0x4 19. "TRIG3_DONE1,TRIG3 done1 interrupt detection." "0: No TRIG3_DONE1 interrupt detected,1: TRIG3_DONE1 interrupt detected" newline eventfld.long 0x4 18. "TRIG2_DONE1,TRIG2 done1 interrupt detection." "0: No TRIG2_DONE1 interrupt detected,1: TRIG2_DONE1 interrupt detected" newline eventfld.long 0x4 17. "TRIG1_DONE1,TRIG1 done1 interrupt detection." "0: No TRIG1_DONE1 interrupt detected,1: TRIG1_DONE1 interrupt detected" newline eventfld.long 0x4 16. "TRIG0_DONE1,TRIG0 done1 interrupt detection." "0: No TRIG0_DONE1 interrupt detected,1: TRIG0_DONE1 interrupt detected" newline eventfld.long 0x4 7. "TRIG7_DONE0,TRIG7 done0 interrupt detection." "0: No TRIG7_DONE0 interrupt detected,1: TRIG7_DONE0 interrupt detected" newline eventfld.long 0x4 6. "TRIG6_DONE0,TRIG6 done0 interrupt detection." "0: No TRIG6_DONE0 interrupt detected,1: TRIG6_DONE0 interrupt detected" newline eventfld.long 0x4 5. "TRIG5_DONE0,TRIG5 done0 interrupt detection." "0: No TRIG5_DONE0 interrupt detected,1: TRIG5_DONE0 interrupt detected" newline eventfld.long 0x4 4. "TRIG4_DONE0,TRIG4 done0 interrupt detection." "0: No TRIG4_DONE0 interrupt detected,1: TRIG4_DONE0 interrupt detected" newline eventfld.long 0x4 3. "TRIG3_DONE0,TRIG3 done0 interrupt detection." "0: No TRIG3_DONE0 interrupt detected,1: TRIG3_DONE0 interrupt detected" newline eventfld.long 0x4 2. "TRIG2_DONE0,TRIG2 done0 interrupt detection." "0: No TRIG2_DONE0 interrupt detected,1: TRIG2_DONE0 interrupt detected" newline eventfld.long 0x4 1. "TRIG1_DONE0,TRIG1 done0 interrupt detection." "0: No TRIG1_DONE0 interrupt detected,1: TRIG1_DONE0 interrupt detected" newline eventfld.long 0x4 0. "TRIG0_DONE0,TRIG0 done0 interrupt detection." "0: No TRIG0_DONE0 interrupt detected,1: TRIG0_DONE0 interrupt detected" line.long 0x8 "DONE2_3_ERR_IRQ,ETC DONE_2. DONE_3 and DONE_ERR IRQ State Register" bitfld.long 0x8 23. "TRIG7_ERR,TRIG7 error interrupt detection." "0: No TRIG7_ERR interrupt detected,1: TRIG7_ERR interrupt detected" newline bitfld.long 0x8 22. "TRIG6_ERR,TRIG6 error interrupt detection." "0: No TRIG6_ERR interrupt detected,1: TRIG6_ERR interrupt detected" newline bitfld.long 0x8 21. "TRIG5_ERR,TRIG5 error interrupt detection." "0: No TRIG5_ERR interrupt detected,1: TRIG5_ERR interrupt detected" newline bitfld.long 0x8 20. "TRIG4_ERR,TRIG4 error interrupt detection." "0: No TRIG4_ERR interrupt detected,1: TRIG4_ERR interrupt detected" newline bitfld.long 0x8 19. "TRIG3_ERR,TRIG3 error interrupt detection." "0: No TRIG3_ERR interrupt detected,1: TRIG3_ERR interrupt detected" newline bitfld.long 0x8 18. "TRIG2_ERR,TRIG2 error interrupt detection." "0: No TRIG2_ERR interrupt detected,1: TRIG2_ERR interrupt detected" newline bitfld.long 0x8 17. "TRIG1_ERR,TRIG1 error interrupt detection." "0: No TRIG1_ERR interrupt detected,1: TRIG1_ERR interrupt detected" newline bitfld.long 0x8 16. "TRIG0_ERR,TRIG0 error interrupt detection." "0: No TRIG0_ERR interrupt detected,1: TRIG0_ERR interrupt detected" newline eventfld.long 0x8 15. "TRIG7_DONE3,TRIG7 done3 interrupt detection." "0: No TRIG7_DONE3 interrupt detected,1: TRIG7_DONE3 interrupt detected" newline eventfld.long 0x8 14. "TRIG6_DONE3,TRIG6 done3 interrupt detection." "0: No TRIG6_DONE3 interrupt detected,1: TRIG6_DONE3 interrupt detected" newline eventfld.long 0x8 13. "TRIG5_DONE3,TRIG5 done3 interrupt detection." "0: No TRIG5_DONE3 interrupt detected,1: TRIG5_DONE3 interrupt detected" newline eventfld.long 0x8 12. "TRIG4_DONE3,TRIG4 done3 interrupt detection." "0: No TRIG4_DONE3 interrupt detected,1: TRIG4_DONE3 interrupt detected" newline eventfld.long 0x8 11. "TRIG3_DONE3,TRIG3 done3 interrupt detection." "0: No TRIG3_DONE3 interrupt detected,1: TRIG3_DONE3 interrupt detected" newline eventfld.long 0x8 10. "TRIG2_DONE3,TRIG2 done3 interrupt detection." "0: No TRIG2_DONE3 interrupt detected,1: TRIG2_DONE3 interrupt detected" newline eventfld.long 0x8 9. "TRIG1_DONE3,TRIG1 done3 interrupt detection." "0: No TRIG1_DONE3 interrupt detected,1: TRIG1_DONE3 interrupt detected" newline eventfld.long 0x8 8. "TRIG0_DONE3,TRIG0 done3 interrupt detection." "0: No TRIG0_DONE3 interrupt detected,1: TRIG0_DONE3 interrupt detected" newline eventfld.long 0x8 7. "TRIG7_DONE2,TRIG7 done2 interrupt detection." "0: No TRIG7_DONE2 interrupt detected,1: TRIG7_DONE2 interrupt detected" newline eventfld.long 0x8 6. "TRIG6_DONE2,TRIG6 done2 interrupt detection." "0: No TRIG6_DONE2 interrupt detected,1: TRIG6_DONE2 interrupt detected" newline eventfld.long 0x8 5. "TRIG5_DONE2,TRIG5 done2 interrupt detection." "0: No TRIG5_DONE2 interrupt detected,1: TRIG5_DONE2 interrupt detected" newline eventfld.long 0x8 4. "TRIG4_DONE2,TRIG4 done2 interrupt detection." "0: No TRIG4_DONE2 interrupt detected,1: TRIG4_DONE2 interrupt detected" newline eventfld.long 0x8 3. "TRIG3_DONE2,TRIG3 done2 interrupt detection." "0: No TRIG3_DONE2 interrupt detected,1: TRIG3_DONE2 interrupt detected" newline eventfld.long 0x8 2. "TRIG2_DONE2,TRIG2 done2 interrupt detection." "0: No TRIG2_DONE2 interrupt detected,1: TRIG2_DONE2 interrupt detected" newline eventfld.long 0x8 1. "TRIG1_DONE2,TRIG1 done2 interrupt detection." "0: No TRIG1_DONE2 interrupt detected,1: TRIG1_DONE2 interrupt detected" newline eventfld.long 0x8 0. "TRIG0_DONE2,TRIG0 done2 interrupt detection." "0: No TRIG0_DONE2 interrupt detected,1: TRIG0_DONE2 interrupt detected" line.long 0xC "DMA_CTRL,ETC DMA control Register" eventfld.long 0xC 23. "TRIG7_REQ,Flag bit for DMA request" "0: TRIG7_REQ not detected.,1: TRIG7_REQ detected." newline eventfld.long 0xC 22. "TRIG6_REQ,Flag bit for DMA request" "0: TRIG6_REQ not detected.,1: TRIG6_REQ detected." newline eventfld.long 0xC 21. "TRIG5_REQ,Flag bit for DMA request" "0: TRIG5_REQ not detected.,1: TRIG5_REQ detected." newline eventfld.long 0xC 20. "TRIG4_REQ,Flag bit for DMA request" "0: TRIG4_REQ not detected.,1: TRIG4_REQ detected." newline eventfld.long 0xC 19. "TRIG3_REQ,Flag bit for DMA request" "0: TRIG3_REQ not detected.,1: TRIG3_REQ detected." newline eventfld.long 0xC 18. "TRIG2_REQ,Flag bit for DMA request" "0: TRIG2_REQ not detected.,1: TRIG2_REQ detected." newline eventfld.long 0xC 17. "TRIG1_REQ,Flag bit for DMA request" "0: TRIG1_REQ not detected.,1: TRIG1_REQ detected." newline eventfld.long 0xC 16. "TRIG0_REQ,Flag bit for DMA request" "0: TRIG0_REQ not detected.,1: TRIG0_REQ detected." newline bitfld.long 0xC 7. "TRIG7_ENABLE,Enable DMA request when TRIG7 done." "0: TRIG7 DMA request disabled.,1: TRIG7 DMA request enabled." newline bitfld.long 0xC 6. "TRIG6_ENABLE,Enable DMA request when TRIG6 done." "0: TRIG6 DMA request disabled.,1: TRIG6 DMA request enabled." newline bitfld.long 0xC 5. "TRIG5_ENABLE,Enable DMA request when TRIG5 done." "0: TRIG5 DMA request disabled.,1: TRIG5 DMA request enabled." newline bitfld.long 0xC 4. "TRIG4_ENABLE,Enable DMA request when TRIG4 done." "0: TRIG4 DMA request disabled.,1: TRIG4 DMA request enabled." newline bitfld.long 0xC 3. "TRIG3_ENABLE,Enable DMA request when TRIG3 done." "0: TRIG3 DMA request disabled.,1: TRIG3 DMA request enabled." newline bitfld.long 0xC 2. "TRIG2_ENABLE,Enable DMA request when TRIG2 done." "0: TRIG2 DMA request disabled.,1: TRIG2 DMA request enabled." newline bitfld.long 0xC 1. "TRIG1_ENABLE,Enable DMA request when TRIG1 done." "0: TRIG1 DMA request disabled.,1: TRIG1 DMA request enabled." newline bitfld.long 0xC 0. "TRIG0_ENABLE,Enable DMA request when TRIG0 done." "0: TRIG0 DMA request disabled.,1: TRIG0 DMA request enabled." line.long 0x10 "TRIG0_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x10 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x10 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x10 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x10 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x10 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x10 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x14 "TRIG0_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x14 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x14 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x18 "TRIG0_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x18 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x18 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x18 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x18 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x18 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x18 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x18 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x18 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x18 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x18 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0x1C "TRIG0_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0x1C 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0x1C 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0x1C 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x1C 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x1C 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0x1C 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0x1C 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0x1C 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x1C 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x1C 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x20 "TRIG0_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x20 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x20 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x20 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x20 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x20 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x20 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x20 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x20 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x20 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x20 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x24 "TRIG0_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x24 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x24 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x24 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x24 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x24 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x24 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x24 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x24 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x24 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x24 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0x28++0xF line.long 0x0 "TRIG0_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG0_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG0_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG0_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0x38++0x17 line.long 0x0 "TRIG1_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG1_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG1_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG1_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG1_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG1_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0x50++0xF line.long 0x0 "TRIG1_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG1_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG1_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG1_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0x60++0x17 line.long 0x0 "TRIG2_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG2_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG2_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG2_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG2_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG2_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0x78++0xF line.long 0x0 "TRIG2_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG2_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG2_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG2_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0x88++0x17 line.long 0x0 "TRIG3_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG3_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG3_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG3_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG3_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG3_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0xA0++0xF line.long 0x0 "TRIG3_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG3_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG3_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG3_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0xB0++0x17 line.long 0x0 "TRIG4_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG4_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG4_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG4_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG4_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG4_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0xC8++0xF line.long 0x0 "TRIG4_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG4_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG4_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG4_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0xD8++0x17 line.long 0x0 "TRIG5_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG5_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG5_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG5_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG5_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG5_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0xF0++0xF line.long 0x0 "TRIG5_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG5_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG5_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG5_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0x100++0x17 line.long 0x0 "TRIG6_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG6_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG6_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG6_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG6_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG6_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0x118++0xF line.long 0x0 "TRIG6_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG6_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG6_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG6_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" group.long 0x128++0x17 line.long 0x0 "TRIG7_CTRL,ETC_TRIG Control Register" hexmask.long.byte 0x0 24.--31. 1. "CHAINx_DONE,Segment x done detection" newline bitfld.long 0x0 16. "SYNC_MODE,Trigger synchronization mode selection" "0: Synchronization mode disabled TRIGa and..,1: Synchronization mode enabled TRIGa and TRIG(a+4).." newline bitfld.long 0x0 12.--14. "TRIG_PRIORITY,External trigger priority 7 is highest priority while 0 is lowest" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "TRIG_CHAIN,The number of segments inside the trigger chain of TRIGa." "0: Trigger chain length is 1,1: Trigger chain length is 2,2: Trigger chain length is 3,3: Trigger chain length is 4,4: Trigger chain length is 5,5: Trigger chain length is 6,6: Trigger chain length is 7,7: Trigger chain length is 8" newline bitfld.long 0x0 4. "TRIG_MODE,Trigger mode selection." "0: Hardware trigger. The softerware trigger will be..,1: Software trigger. The hardware trigger will be.." newline bitfld.long 0x0 0. "SW_TRIG,Software trigger. This field is self-clearing." "0: No software trigger event generated.,1: Software trigger event generated." line.long 0x4 "TRIG7_COUNTER,ETC_TRIG Counter Register" hexmask.long.word 0x4 16.--31. 1. "SAMPLE_INTERVAL,TRIGGER sampling interval counter" newline hexmask.long.word 0x4 0.--15. 1. "INIT_DELAY,TRIGGER initial delay counter. Initial_delay = (INIT_DELAY+1)*(PRE_DIVIDER+1)*ipg_clk" line.long 0x8 "TRIG7_CHAIN_1_0,ETC_TRIG Chain 0/1 Register" bitfld.long 0x8 31. "IE1_EN,IRQ enable of segment 1." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 1 finish an.." newline bitfld.long 0x8 29.--30. "IE1,Segment 1 interrupt enable. (This bit field is meaningful only when IE1_EN is set)" "0: Generate interrupt on Done0 when Segment 1 finish.,1: Generate interrupt on Done1 when Segment 1 finish.,2: Generate interrupt on Done2 when Segment 1 finish.,3: Generate interrupt on Done3 when Segment 1 finish." newline bitfld.long 0x8 28. "B2B1,Segment 1 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 20.--27. 1. "HWTS1,Segment 1 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 16.--19. 1. "CSEL1,ADC hardware trigger command selection" newline bitfld.long 0x8 15. "IE0_EN,IRQ enable of segment 0." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 0 finish an.." newline bitfld.long 0x8 13.--14. "IE0,Segment 0 interrupt enable. (This bit field is meaningful only when IE0_EN is set)" "0: Generate interrupt on Done0 when segment 0 finish.,1: Generate interrupt on Done1 when segment 0 finish.,2: Generate interrupt on Done2 when segment 0 finish.,3: Generate interrupt on Done3 when segment 0 finish." newline bitfld.long 0x8 12. "B2B0,Segment 0 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x8 4.--11. 1. "HWTS0,Segment 0 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x8 0.--3. 1. "CSEL0,ADC hardware trigger command selection" line.long 0xC "TRIG7_CHAIN_3_2,ETC_TRIG Chain 2/3 Register" bitfld.long 0xC 31. "IE3_EN,IRQ enable of segment 3." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 3 finish an.." newline bitfld.long 0xC 29.--30. "IE3,Segment 3 interrupt enable. (This bit field is meaningful only when IE3_EN is set)" "0: Generate interrupt on Done0 when segment 3 finish.,1: Generate interrupt on Done1 when segment 3 finish.,2: Generate interrupt on Done2 when segment 3 finish.,3: Generate interrupt on Done3 when segment 3 finish." newline bitfld.long 0xC 28. "B2B3,Segment 3 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 20.--27. 1. "HWTS3,Segment 3 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 16.--19. 1. "CSEL3,ADC hardware trigger command selection" newline bitfld.long 0xC 15. "IE2_EN,IRQ enable of segment 2." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 2 finish an.." newline bitfld.long 0xC 13.--14. "IE2,Segment 2 interrupt enable. (This bit field is meaningful only when IE2_EN is set)" "0: Generate interrupt on Done0 when segment 2 finish.,1: Generate interrupt on Done1 when segment 2 finish.,2: Generate interrupt on Done2 when segment 2 finish.,3: Generate interrupt on Done3 when segment 2 finish." newline bitfld.long 0xC 12. "B2B2,Segment 2 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0xC 4.--11. 1. "HWTS2,Segment 2 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0xC 0.--3. 1. "CSEL2,ADC hardware trigger command selection" line.long 0x10 "TRIG7_CHAIN_5_4,ETC_TRIG Chain 4/5 Register" bitfld.long 0x10 31. "IE5_EN,IRQ enable of segment 5." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 5 finish an.." newline bitfld.long 0x10 29.--30. "IE5,Segment 5 interrupt enable. (This bit field is meaningful only when IE5_EN is set)" "0: Generate interrupt on Done0 when segment 5 finish.,1: Generate interrupt on Done1 when segment 5 finish.,2: Generate interrupt on Done2 when segment 5 finish.,3: Generate interrupt on Done3 when segment 5 finish." newline bitfld.long 0x10 28. "B2B5,Segment 5 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 20.--27. 1. "HWTS5,Segment 5 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 16.--19. 1. "CSEL5,ADC hardware trigger command selection" newline bitfld.long 0x10 15. "IE4_EN,IRQ enable of segment 4." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 4 finish an.." newline bitfld.long 0x10 13.--14. "IE4,Segment 4 interrupt enable. (This bit field is meaningful only when IE4_EN is set)" "0: Generate interrupt on Done0 when segment 4 finish.,1: Generate interrupt on Done1 when segment 4 finish.,2: Generate interrupt on Done2 when segment 4 finish.,3: Generate interrupt on Done3 when segment 4 finish." newline bitfld.long 0x10 12. "B2B4,Segment 4 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x10 4.--11. 1. "HWTS4,Segment 4 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x10 0.--3. 1. "CSEL4,ADC hardware trigger command selection" line.long 0x14 "TRIG7_CHAIN_7_6,ETC_TRIG Chain 6/7 Register" bitfld.long 0x14 31. "IE7_EN,IRQ enable of segment 7." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 7 finish an.." newline bitfld.long 0x14 29.--30. "IE7,Segment 7 interrupt enable. (This bit field is meaningful only when IE7_EN is set)" "0: Generate interrupt on Done0 when segment 7 finish.,1: Generate interrupt on Done1 when segment 7 finish.,2: Generate interrupt on Done2 when segment 7 finish.,3: Generate interrupt on Done3 when segment 7 finish." newline bitfld.long 0x14 28. "B2B7,Segment 7 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 20.--27. 1. "HWTS7,Segment 7 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 16.--19. 1. "CSEL7,ADC hardware trigger command selection" newline bitfld.long 0x14 15. "IE6_EN,IRQ enable of segment 6." "0: Interrupt DONE disabled.,1: Interrupt DONE enabled. When segment 6 finish an.." newline bitfld.long 0x14 13.--14. "IE6,Segment 6 interrupt enable. (This bit field is meaningful only when IE6_EN is set)" "0: Generate interrupt on Done0 when segment 6 finish.,1: Generate interrupt on Done1 when segment 6 finish.,2: Generate interrupt on Done2 when segment 6 finish.,3: Generate interrupt on Done3 when segment 6 finish." newline bitfld.long 0x14 12. "B2B6,Segment 6 B2B" "0: Disable B2B. Wait until delay value defined by..,1: Enable B2B. When Segment 0 finished (ADC COCO).." newline hexmask.long.byte 0x14 4.--11. 1. "HWTS6,Segment 6 HWTS ADC hardware trigger selection" newline hexmask.long.byte 0x14 0.--3. 1. "CSEL6,ADC hardware trigger command selection" rgroup.long 0x140++0xF line.long 0x0 "TRIG7_RESULT_1_0,ETC_TRIG Result Data 1/0 Register" hexmask.long.word 0x0 16.--27. 1. "DATA1,Result DATA1The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x0 0.--11. 1. "DATA0,Result DATA0The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x4 "TRIG7_RESULT_3_2,ETC_TRIG Result Data 3/2 Register" hexmask.long.word 0x4 16.--27. 1. "DATA3,Result DATA3The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x4 0.--11. 1. "DATA2,Result DATA2The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0x8 "TRIG7_RESULT_5_4,ETC_TRIG Result Data 5/4 Register" hexmask.long.word 0x8 16.--27. 1. "DATA5,Result DATA5The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0x8 0.--11. 1. "DATA4,Result DATA4The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" line.long 0xC "TRIG7_RESULT_7_6,ETC_TRIG Result Data 7/6 Register" hexmask.long.word 0xC 16.--27. 1. "DATA7,Result DATA7The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" newline hexmask.long.word 0xC 0.--11. 1. "DATA6,Result DATA6The sign bit from ADC result FIFO is ignored by ETC_TRIG result so only 12-bit unsigned results is supported by ADC_ETC module" tree.end tree "ANADIG" base ad:0x0 tree "ANADIG_LDO_SNVS" base ad:0x40C84000 group.long 0x510++0x3 line.long 0x0 "PMU_LDO_LPSR_ANA,PMU_LDO_LPSR_ANA_REGISTER" bitfld.long 0x0 20. "PULL_DOWN_20UA_EN,pull_down_20ua_en" "0,1" bitfld.long 0x0 19. "TRACK_MODE_EN,Track Mode Enable" "0: Normal use,1: Switch preparation" bitfld.long 0x0 8. "ALWAYS_4MA_PULLDOWN_EN,always_4ma_pulldown_en" "0,1" newline bitfld.long 0x0 6. "STANDBY_EN,standby_en" "0,1" bitfld.long 0x0 5. "BYPASS_MODE_EN,bypass_mode_en" "0,1" bitfld.long 0x0 4. "LPSR_ANA_CONTROL_MODE,LPSR_ANA_CONTROL_MODE" "0: SW Control,1: HW Control" newline bitfld.long 0x0 3. "PULL_DOWN_2MA_EN,pull_down_2ma_en" "0,1" bitfld.long 0x0 2. "REG_DISABLE,reg_disable" "0,1" bitfld.long 0x0 0. "REG_LP_EN,reg_lp_en" "0,1" group.long 0x520++0x3 line.long 0x0 "PMU_LDO_LPSR_DIG_2,PMU_LDO_LPSR_DIG_2_REGISTER" bitfld.long 0x0 0.--1. "VOLTAGE_STEP_INC,voltage_step_inc" "0,1,2,3" group.long 0x530++0x3 line.long 0x0 "PMU_LDO_LPSR_DIG,PMU_LDO_LPSR_DIG_REGISTER" hexmask.long.byte 0x0 20.--24. 1. "VOLTAGE_SELECT,VOLTAGE_SELECT" bitfld.long 0x0 18. "BYPASS_MODE,bypass_mode" "0,1" bitfld.long 0x0 17. "TRACKING_MODE,tracking_mode" "0,1" newline bitfld.long 0x0 6. "STANDBY_EN,standby_en" "0,1" bitfld.long 0x0 5. "LPSR_DIG_CONTROL_MODE,LPSR_DIG_CONTROL_MODE" "0: SW Control,1: HW Control" bitfld.long 0x0 2. "REG_EN,ENABLE_ILIMIT" "0,1" tree.end tree "ANADIG_LDO_SNVS_DIG" base ad:0x40C84000 group.long 0x540++0x3 line.long 0x0 "PMU_LDO_SNVS_DIG,PMU_LDO_SNVS_DIG_REGISTER" bitfld.long 0x0 2. "REG_EN,REG_EN" "0,1" bitfld.long 0x0 1. "TEST_OVERRIDE,test_override" "0,1" bitfld.long 0x0 0. "REG_LP_EN,REG_LP_EN" "0,1" tree.end tree "ANADIG_MISC" base ad:0x40C84000 rgroup.long 0x800++0x3 line.long 0x0 "MISC_DIFPROG,Chip Silicon Version Register" hexmask.long 0x0 0.--31. 1. "CHIPID,Chip ID" group.long 0x820++0x3 line.long 0x0 "VDDSOC_AI_CTRL,VDDSOC_AI_CTRL_REGISTER" bitfld.long 0x0 16. "VDDSOC_AIRWB,VDDSOC_AIRWB" "0,1" hexmask.long.byte 0x0 0.--7. 1. "VDDSOC_AI_ADDR,VDDSOC_AI_ADDR" group.long 0x830++0x3 line.long 0x0 "VDDSOC_AI_WDATA,VDDSOC_AI_WDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC_AI_WDATA,VDDSOC_AI_WDATA" rgroup.long 0x840++0x3 line.long 0x0 "VDDSOC_AI_RDATA,VDDSOC_AI_RDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC_AI_RDATA,VDDSOC_AI_RDATA" group.long 0x850++0x3 line.long 0x0 "VDDSOC2PLL_AI_CTRL_1G,VDDSOC2PLL_AI_CTRL_1G_REGISTER" bitfld.long 0x0 16. "VDDSOC2PLL_AIRWB_1G,VDDSOC2PLL_AIRWB_1G" "0,1" rbitfld.long 0x0 9. "VDDSOC2PLL_AITOGGLE_DONE_1G,VDDSOC2PLL_AITOGGLE_DONE_1G" "0,1" bitfld.long 0x0 8. "VDDSOC2PLL_AITOGGLE_1G,VDDSOC2PLL_AITOGGLE_1G" "0,1" newline hexmask.long.byte 0x0 0.--7. 1. "VDDSOC2PLL_AIADDR_1G,VDDSOC2PLL_AIADDR_1G" group.long 0x860++0x3 line.long 0x0 "VDDSOC2PLL_AI_WDATA_1G,VDDSOC2PLL_AI_WDATA_1G_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_WDATA_1G,VDDSOC2PLL_AI_WDATA_1G" rgroup.long 0x870++0x3 line.long 0x0 "VDDSOC2PLL_AI_RDATA_1G,VDDSOC2PLL_AI_RDATA_1G_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_RDATA_1G,VDDSOC2PLL_AI_RDATA_1G" group.long 0x880++0x3 line.long 0x0 "VDDSOC2PLL_AI_CTRL_AUDIO,VDDSOC_AI_CTRL_AUDIO_REGISTER" bitfld.long 0x0 16. "VDDSOC2PLL_AIRWB_AUDIO,VDDSOC_AIRWB" "0,1" rbitfld.long 0x0 9. "VDDSOC2PLL_AITOGGLE_DONE_AUDIO,VDDSOC2PLL_AITOGGLE_DONE_AUDIO" "0,1" bitfld.long 0x0 8. "VDDSOC2PLL_AITOGGLE_AUDIO,VDDSOC2PLL_AITOGGLE_AUDIO" "0,1" newline hexmask.long.byte 0x0 0.--7. 1. "VDDSOC2PLL_AI_ADDR_AUDIO,VDDSOC2PLL_AI_ADDR_AUDIO" group.long 0x890++0x3 line.long 0x0 "VDDSOC2PLL_AI_WDATA_AUDIO,VDDSOC_AI_WDATA_AUDIO_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_WDATA_AUDIO,VDDSOC2PLL_AI_WDATA_AUDIO" rgroup.long 0x8A0++0x3 line.long 0x0 "VDDSOC2PLL_AI_RDATA_AUDIO,VDDSOC2PLL_AI_RDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_RDATA_AUDIO,VDDSOC2PLL_AI_RDATA_AUDIO" group.long 0x8B0++0x3 line.long 0x0 "VDDSOC2PLL_AI_CTRL_VIDEO,VDDSOC2PLL_AI_CTRL_VIDEO_REGISTER" bitfld.long 0x0 16. "VDDSOC2PLL_AIRWB_VIDEO,VDDSOC2PLL_AIRWB_VIDEO" "0,1" rbitfld.long 0x0 9. "VDDSOC2PLL_AITOGGLE_DONE_VIDEO,VDDSOC2PLL_AITOGGLE_DONE_VIDEO" "0,1" bitfld.long 0x0 8. "VDDSOC2PLL_AITOGGLE_VIDEO,VDDSOC2PLL_AITOGGLE_VIDEO" "0,1" newline hexmask.long.byte 0x0 0.--7. 1. "VDDSOC2PLL_AIADDR_VIDEO,VDDSOC2PLL_AIADDR_VIDEO" group.long 0x8C0++0x3 line.long 0x0 "VDDSOC2PLL_AI_WDATA_VIDEO,VDDSOC2PLL_AI_WDATA_VIDEO_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_WDATA_VIDEO,VDDSOC2PLL_AI_WDATA_VIDEO" rgroup.long 0x8D0++0x3 line.long 0x0 "VDDSOC2PLL_AI_RDATA_VIDEO,VDDSOC2PLL_AI_RDATA_VIDEO_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDSOC2PLL_AI_RDATA_VIDEO,VDDSOC2PLL_AI_RDATA_VIDEO" group.long 0x8E0++0x3 line.long 0x0 "VDDLPSR_AI_CTRL,VDDSOC_AI_CTRL_REGISTER" bitfld.long 0x0 16. "VDDLPSR_AIRWB,VDDLPSR_AIRWB" "0,1" hexmask.long.byte 0x0 0.--7. 1. "VDDLPSR_AI_ADDR,VDDLPSR_AI_ADDR" group.long 0x8F0++0x3 line.long 0x0 "VDDLPSR_AI_WDATA,VDDLPSR_AI_WDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDLPSR_AI_WDATA,VDD_LPSR_AI_WDATA" rgroup.long 0x900++0x3 line.long 0x0 "VDDLPSR_AI_RDATA_REFTOP,VDDLPSR_AI_RDATA_REFTOP_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDLPSR_AI_RDATA_REFTOP,VDDLPSR_AI_RDATA_REFTOP" rgroup.long 0x910++0x3 line.long 0x0 "VDDLPSR_AI_RDATA_TMPSNS,VDDLPSR_AI_RDATA_TMPSNS_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDLPSR_AI_RDATA_TMPSNS,VDDLPSR_AI_RDATA_TMPSNS" group.long 0x920++0x3 line.long 0x0 "VDDLPSR_AI400M_CTRL,VDDLPSR_AI400M_CTRL_REGISTER" bitfld.long 0x0 16. "VDDLPSR_AI400M_RWB,VDDLPSR_AI400M_RWB" "0,1" rbitfld.long 0x0 9. "VDDLPSR_AITOGGLE_DONE_400M,VDDLPSR_AITOGGLE_DONE_400M" "0,1" bitfld.long 0x0 8. "VDDLPSR_AITOGGLE_400M,VDDLPSR_AITOGGLE_400M" "0,1" newline hexmask.long.byte 0x0 0.--7. 1. "VDDLPSR_AI400M_ADDR,VDDLPSR_AI400M_ADDR" group.long 0x930++0x3 line.long 0x0 "VDDLPSR_AI400M_WDATA,VDDLPSR_AI400M_WDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDLPSR_AI400M_WDATA,VDDLPSR_AI400M_WDATA" rgroup.long 0x940++0x3 line.long 0x0 "VDDLPSR_AI400M_RDATA,VDDLPSR_AI400M_RDATA_REGISTER" hexmask.long 0x0 0.--31. 1. "VDDLPSR_AI400M_RDATA,VDDLPSR_AI400M_RDATA" tree.end tree "ANADIG_OSC" base ad:0x40C84000 group.long 0x10++0x3 line.long 0x0 "OSC_48M_CTRL,48MHz RCOSC Control Register" bitfld.long 0x0 31. "RC_48M_CONTROL_MODE,48MHz RCOSC Control Mode" "0: Software mode (default),1: GPC mode (Setpoint)" newline bitfld.long 0x0 30. "RC_48M_DIV2_CONTROL_MODE,RCOSC_48M_DIV2 Control Mode" "0: Software mode (default),1: GPC mode (Setpoint)" newline bitfld.long 0x0 24. "RC_48M_DIV2_EN,RCOSC_48M_DIV2 Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 1. "TEN,48MHz RCOSC Enable" "0: Power down,1: Power up" group.long 0x20++0x3 line.long 0x0 "OSC_24M_CTRL,24MHz OSC Control Register" bitfld.long 0x0 31. "OSC_24M_CONTROL_MODE,24MHz OSC Control Mode" "0: Software mode (default),1: GPC mode (Setpoint)" newline rbitfld.long 0x0 30. "OSC_24M_STABLE,24MHz OSC Stable" "0: Not Stable,1: Stable" newline bitfld.long 0x0 7. "OSC_24M_GATE,24MHz OSC Gate Control" "0: Not Gated,1: Gated" newline bitfld.long 0x0 4. "OSC_EN,24MHz OSC Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 3. "OSC_COMP_MODE,24MHz OSC Comparator Mode" "0: Single-ended mode (default),1: Differential mode (test mode)" newline bitfld.long 0x0 2. "LP_EN,24MHz OSC Low-Power Mode Enable" "0: High Gain mode (HP),1: Low-power mode (LP)" newline bitfld.long 0x0 1. "BYPASS_EN,24MHz OSC Bypass Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 0. "BYPASS_CLK,24MHz OSC Bypass Clock" "0,1" rgroup.long 0x40++0x3 line.long 0x0 "OSC_400M_CTRL0,400MHz RCOSC Control0 Register" bitfld.long 0x0 31. "OSC400M_AI_BUSY,400MHz OSC AI BUSY" "0,1" group.long 0x50++0x3 line.long 0x0 "OSC_400M_CTRL1,400MHz RCOSC Control1 Register" bitfld.long 0x0 31. "RC_400M_CONTROL_MODE,400MHz RCOSC Control mode" "0: Software mode (default),1: GPC mode (Setpoint)" newline bitfld.long 0x0 1. "CLKGATE_400MEG,Clock gate control for 400MHz RCOSC" "0: Not Gated,1: Gated" newline bitfld.long 0x0 0. "PWD,Power down control for 400MHz RCOSC" "0: No Power down,1: Power down" group.long 0x60++0x3 line.long 0x0 "OSC_400M_CTRL2,400MHz RCOSC Control2 Register" hexmask.long.byte 0x0 24.--31. 1. "OSC_TUNE_VAL,Oscillator Tune Value" newline bitfld.long 0x0 10. "TUNE_BYP,Bypass tuning logic" "0: Use the output of tuning logic to run the..,1: Bypass the tuning logic and use the programmed.." newline bitfld.long 0x0 0. "ENABLE_CLK,Clock enable" "0: Clock is disabled before entering GPC mode,1: Clock is enabled before entering GPC mode" group.long 0xC0++0x3 line.long 0x0 "OSC_16M_CTRL,16MHz RCOSC Control Register" bitfld.long 0x0 31. "RC_16M_CONTROL_MODE,Control Mode for 16MHz Oscillator" "0: Software mode (default),1: GPC mode (Setpoint)" newline bitfld.long 0x0 8. "SOURCE_SEL_16M,Source select" "0: 16MHz Oscillator,1: 24MHz Oscillator" newline bitfld.long 0x0 3. "EN_POWER_SAVE,Power Save Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 1. "EN_IRC4M16M,Enable Clock Output" "0: Disable,1: Enable" tree.end tree "ANADIG_PLL" base ad:0x40C84000 group.long 0x200++0x3 line.long 0x0 "ARM_PLL_CTRL,ARM_PLL_CTRL_REGISTER" bitfld.long 0x0 31. "ARM_PLL_CONTROL_MODE,pll_arm_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 30. "ARM_PLL_GATE,ARM_PLL_GATE" "0: Clock is not gated,1: Clock is gated" newline rbitfld.long 0x0 29. "ARM_PLL_STABLE,ARM_PLL_STABLE" "0: ARM PLL is not stable,1: ARM PLL is stable" newline bitfld.long 0x0 17. "BYPASS,Bypass the pll." "0: Function mode,1: Bypass Mode" newline bitfld.long 0x0 15.--16. "POST_DIV_SEL,POST_DIV_SEL" "0: Divide by 2,1: Divide by 4,2: Divide by 8,3: Divide by 1" newline bitfld.long 0x0 14. "ENABLE_CLK,Enable the clock output." "0: Disable the clock,1: Enable the clock" newline bitfld.long 0x0 13. "POWERUP,Powers up the PLL." "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 12. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" newline hexmask.long.byte 0x0 0.--7. 1. "DIV_SELECT,DIV_SELECT" group.long 0x210++0x3 line.long 0x0 "SYS_PLL3_CTRL,SYS_PLL3_CTRL_REGISTER" bitfld.long 0x0 31. "SYS_PLL3_CONTROL_MODE,SYS_PLL3_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 30. "SYS_PLL3_GATE,SYS_PLL3_GATE" "0: Clock is not gated,1: Clock is gated" newline rbitfld.long 0x0 29. "SYS_PLL3_STABLE,SYS_PLL3_STABLE" "0,1" newline bitfld.long 0x0 28. "SYS_PLL3_DIV2_CONTROL_MODE,SYS_PLL3_DIV2_CONTROL_MODE" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 21. "POWERUP,Powers up the PLL." "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 16. "BYPASS,BYPASS" "0: Function mode,1: Bypass Mode" newline bitfld.long 0x0 13. "ENABLE_CLK,Enable the clock output." "0: Disable the clock,1: Enable the clock" newline bitfld.long 0x0 11. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" newline bitfld.long 0x0 4. "PLL_REG_EN,Enable Internal PLL Regulator" "0,1" newline bitfld.long 0x0 3. "SYS_PLL3_DIV2,SYS PLL3 DIV2 gate" "0,1" group.long 0x220++0x3 line.long 0x0 "SYS_PLL3_UPDATE,SYS_PLL3_UPDATE_REGISTER" bitfld.long 0x0 8. "PFD3_CONTROL_MODE,pfd3_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 7. "PDF2_CONTROL_MODE,pdf2_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 6. "PFD1_CONTROL_MODE,pfd1_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 5. "PFD0_CONTROL_MODE,pfd0_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 4. "PFD3_UPDATE,PFD3_UPDATE" "0,1" newline bitfld.long 0x0 3. "PFD2_UPDATE,PFD2_OVERRIDE" "0,1" newline bitfld.long 0x0 2. "PFD1_UPDATE,PFD1_OVERRIDE" "0,1" newline bitfld.long 0x0 1. "PFD0_UPDATE,PFD0_OVERRIDE" "0,1" group.long 0x230++0x3 line.long 0x0 "SYS_PLL3_PFD,SYS_PLL3_PFD_REGISTER" bitfld.long 0x0 31. "PFD3_DIV1_CLKGATE,PFD3_DIV1_CLKGATE" "0: ref_pfd3 fractional divider clock is enabled,1: Fractional divider clock (reference ref_pfd3) is.." newline rbitfld.long 0x0 30. "PFD3_STABLE,PFD3_STABLE" "0,1" newline hexmask.long.byte 0x0 24.--29. 1. "PFD3_FRAC,PFD3_FRAC" newline bitfld.long 0x0 23. "PFD2_DIV1_CLKGATE,PFD2_DIV1_CLKGATE" "0: ref_pfd2 fractional divider clock is enabled,1: Fractional divider clock (reference ref_pfd2) is.." newline rbitfld.long 0x0 22. "PFD2_STABLE,PFD2_STABLE" "0,1" newline hexmask.long.byte 0x0 16.--21. 1. "PFD2_FRAC,PFD2_FRAC" newline bitfld.long 0x0 15. "PFD1_DIV1_CLKGATE,PFD1_DIV1_CLKGATE" "0: ref_pfd1 fractional divider clock is enabled,1: Fractional divider clock (reference ref_pfd1) is.." newline rbitfld.long 0x0 14. "PFD1_STABLE,PFD1_STABLE" "0,1" newline hexmask.long.byte 0x0 8.--13. 1. "PFD1_FRAC,PFD1_FRAC" newline bitfld.long 0x0 7. "PFD0_DIV1_CLKGATE,PFD0_DIV1_CLKGATE" "0: ref_pfd0 fractional divider clock is enabled,1: Fractional divider clock (reference ref_pfd0) is.." newline rbitfld.long 0x0 6. "PFD0_STABLE,PFD0_STABLE" "0,1" newline hexmask.long.byte 0x0 0.--5. 1. "PFD0_FRAC,PFD0_FRAC" group.long 0x240++0x3 line.long 0x0 "SYS_PLL2_CTRL,SYS_PLL2_CTRL_REGISTER" bitfld.long 0x0 31. "SYS_PLL2_CONTROL_MODE,SYS_PLL2_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 30. "SYS_PLL2_GATE,SYS_PLL2_GATE" "0: Clock is not gated,1: Clock is gated" newline rbitfld.long 0x0 29. "SYS_PLL2_STABLE,SYS_PLL2_STABLE" "0,1" newline bitfld.long 0x0 23. "POWERUP,Powers up the PLL." "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 19. "PLL_DDR_OVERRIDE,PLL_DDR_OVERRIDE" "0,1" newline bitfld.long 0x0 18. "PFD_OFFSET_EN,PFD_OFFSET_EN" "0,1" newline bitfld.long 0x0 17. "DITHER_ENABLE,DITHER_ENABLE" "0: Disable Dither,1: Enable Dither" newline bitfld.long 0x0 16. "BYPASS,Bypass the pll." "0: Function mode,1: Bypass Mode" newline bitfld.long 0x0 13. "ENABLE_CLK,Enable the clock output." "0: Disable the clock,1: Enable the clock" newline bitfld.long 0x0 11. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" newline bitfld.long 0x0 3. "PLL_REG_EN,Enable Internal PLL Regulator" "0,1" group.long 0x250++0x3 line.long 0x0 "SYS_PLL2_UPDATE,SYS_PLL2_UPDATE_REGISTER" bitfld.long 0x0 8. "PFD3_CONTROL_MODE,pfd3_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 7. "PFD2_CONTROL_MODE,pfd2_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 6. "PFD1_CONTROL_MODE,pfd1_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 5. "PFD0_CONTROL_MODE,pfd0_control_mode" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 4. "PFD3_UPDATE,PFD3_UPDATE" "0,1" newline bitfld.long 0x0 3. "PFD2_UPDATE,PFD2_UPDATE" "0,1" newline bitfld.long 0x0 2. "PFD1_UPDATE,PFD1_UPDATE" "0,1" newline bitfld.long 0x0 1. "PFD0_UPDATE,PFD0_UPDATE" "0,1" group.long 0x260++0x3 line.long 0x0 "SYS_PLL2_SS,SYS_PLL2_SS_REGISTER" hexmask.long.word 0x0 16.--31. 1. "STOP,STOP" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable Spread Spectrum,1: Enable Spread Spectrum" newline hexmask.long.word 0x0 0.--14. 1. "STEP,STEP" group.long 0x270++0x3 line.long 0x0 "SYS_PLL2_PFD,SYS_PLL2_PFD_REGISTER" bitfld.long 0x0 31. "PFD3_DIV1_CLKGATE,PFD3_DIV1_CLKGATE" "0,1" newline rbitfld.long 0x0 30. "PFD3_STABLE,PFD3_STABLE" "0,1" newline hexmask.long.byte 0x0 24.--29. 1. "PFD3_FRAC,PFD3_FRAC" newline bitfld.long 0x0 23. "PFD2_DIV1_CLKGATE,PFD2_DIV1_CLKGATE" "0,1" newline rbitfld.long 0x0 22. "PFD2_STABLE,PFD2_STABLE" "0,1" newline hexmask.long.byte 0x0 16.--21. 1. "PFD2_FRAC,PFD2_FRAC" newline bitfld.long 0x0 15. "PFD1_DIV1_CLKGATE,PFD1_DIV1_CLKGATE" "0,1" newline rbitfld.long 0x0 14. "PFD1_STABLE,PFD1_STABLE" "0,1" newline hexmask.long.byte 0x0 8.--13. 1. "PFD1_FRAC,PFD1_FRAC" newline bitfld.long 0x0 7. "PFD0_DIV1_CLKGATE,PFD0_DIV1_CLKGATE" "0,1" newline rbitfld.long 0x0 6. "PFD0_STABLE,PFD0_STABLE" "0,1" newline hexmask.long.byte 0x0 0.--5. 1. "PFD0_FRAC,PFD0_FRAC" group.long 0x2A0++0x3 line.long 0x0 "SYS_PLL2_MFD,SYS_PLL2_MFD_REGISTER" hexmask.long 0x0 0.--29. 1. "MFD,Denominator" group.long 0x2B0++0x3 line.long 0x0 "SYS_PLL1_SS,SYS_PLL1_SS_REGISTER" hexmask.long.word 0x0 16.--31. 1. "STOP,STOP" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable Spread Spectrum,1: Enable Spread Spectrum" newline hexmask.long.word 0x0 0.--14. 1. "STEP,STEP" group.long 0x2C0++0x3 line.long 0x0 "SYS_PLL1_CTRL,SYS_PLL1_CTRL_REGISTER" bitfld.long 0x0 31. "SYS_PLL1_CONTROL_MODE,SYS_PLL1_CONTROL_MODE" "0: Software Mode (Default),1: GPC Mode" newline rbitfld.long 0x0 30. "SYS_PLL1_AI_BUSY,SYS_PLL1_AI_BUSY" "0,1" newline rbitfld.long 0x0 29. "SYS_PLL1_STABLE,SYS_PLL1_STABLE" "0,1" newline bitfld.long 0x0 28. "SYS_PLL1_DIV2_CONTROL_MODE,SYS_PLL1_DIV2_CONTROL_MODE" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 27. "SYS_PLL1_DIV5_CONTROL_MODE,SYS_PLL1_DIV5_CONTROL_MODE" "0: Software Mode (Default),1: GPC Mode" newline bitfld.long 0x0 26. "SYS_PLL1_DIV5,SYS_PLL1_DIV5" "0,1" newline bitfld.long 0x0 25. "SYS_PLL1_DIV2,SYS_PLL1_DIV2" "0,1" newline bitfld.long 0x0 14. "SYS_PLL1_GATE,SYS_PLL1_GATE" "0: No gate,1: Gate the output" newline bitfld.long 0x0 13. "ENABLE_CLK,ENABLE_CLK" "0,1" group.long 0x2D0++0x3 line.long 0x0 "SYS_PLL1_DENOMINATOR,SYS_PLL1_DENOMINATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "DENOM,DENOM" group.long 0x2E0++0x3 line.long 0x0 "SYS_PLL1_NUMERATOR,SYS_PLL1_NUMERATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "NUM,NUM" group.long 0x2F0++0x3 line.long 0x0 "SYS_PLL1_DIV_SELECT,SYS_PLL1_DIV_SELECT_REGISTER" hexmask.long.byte 0x0 0.--6. 1. "DIV_SELECT,DIV_SELECT" group.long 0x300++0x3 line.long 0x0 "PLL_AUDIO_CTRL,PLL_AUDIO_CTRL_REGISTER" bitfld.long 0x0 31. "PLL_AUDIO_CONTROL_MODE,pll_audio_control_mode" "0: Software Mode (Default),1: GPC Mode" newline rbitfld.long 0x0 30. "PLL_AUDIO_AI_BUSY,pll_audio_ai_busy" "0,1" newline rbitfld.long 0x0 29. "PLL_AUDIO_STABLE,PLL_AUDIO_STABLE" "0,1" newline bitfld.long 0x0 14. "PLL_AUDIO_GATE,PLL_AUDIO_GATE" "0: No gate,1: Gate the output" newline bitfld.long 0x0 13. "ENABLE_CLK,ENABLE_CLK" "0,1" group.long 0x310++0x3 line.long 0x0 "PLL_AUDIO_SS,PLL_AUDIO_SS_REGISTER" hexmask.long.word 0x0 16.--31. 1. "STOP,STOP" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable Spread Spectrum,1: Enable Spread Spectrum" newline hexmask.long.word 0x0 0.--14. 1. "STEP,STEP" group.long 0x320++0x3 line.long 0x0 "PLL_AUDIO_DENOMINATOR,PLL_AUDIO_DENOMINATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "DENOM,DENOM" group.long 0x330++0x3 line.long 0x0 "PLL_AUDIO_NUMERATOR,PLL_AUDIO_NUMERATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "NUM,NUM" group.long 0x340++0x3 line.long 0x0 "PLL_AUDIO_DIV_SELECT,PLL_AUDIO_DIV_SELECT_REGISTER" hexmask.long.byte 0x0 0.--6. 1. "PLL_AUDIO_DIV_SELECT,PLL_AUDIO_DIV_SELECT" group.long 0x350++0x3 line.long 0x0 "PLL_VIDEO_CTRL,PLL_VIDEO_CTRL_REGISTER" bitfld.long 0x0 31. "PLL_VIDEO_CONTROL_MODE,pll_video_control_mode" "0: Software Mode (Default),1: GPC Mode" newline rbitfld.long 0x0 30. "PLL_VIDEO_AI_BUSY,pll_video_ai_busy" "0,1" newline rbitfld.long 0x0 29. "PLL_VIDEO_STABLE,PLL_VIDEO_STABLE" "0,1" newline bitfld.long 0x0 24. "PLL_VIDEO_COUNTER_CLR,pll_video_counter_clr" "0,1" newline bitfld.long 0x0 14. "PLL_VIDEO_GATE,PLL_VIDEO_GATE" "0: No gate,1: Gate the output" newline bitfld.long 0x0 13. "ENABLE_CLK,ENABLE_CLK" "0,1" group.long 0x360++0x3 line.long 0x0 "PLL_VIDEO_SS,PLL_VIDEO_SS_REGISTER" hexmask.long.word 0x0 16.--31. 1. "STOP,STOP" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable Spread Spectrum,1: Enable Spread Spectrum" newline hexmask.long.word 0x0 0.--14. 1. "STEP,STEP" group.long 0x370++0x3 line.long 0x0 "PLL_VIDEO_DENOMINATOR,PLL_VIDEO_DENOMINATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "DENOM,DENOM" group.long 0x380++0x3 line.long 0x0 "PLL_VIDEO_NUMERATOR,PLL_VIDEO_NUMERATOR_REGISTER" hexmask.long 0x0 0.--29. 1. "NUM,NUM" group.long 0x390++0x3 line.long 0x0 "PLL_VIDEO_DIV_SELECT,PLL_VIDEO_DIV_SELECT_REGISTER" hexmask.long.byte 0x0 0.--6. 1. "DIV_SELECT,DIV_SELECT" tree.end tree "ANADIG_PMU" base ad:0x40C84000 group.long 0x500++0x3 line.long 0x0 "PMU_LDO_PLL,PMU_LDO_PLL_REGISTER" rbitfld.long 0x0 30. "LDO_PLL_AI_BUSY,ldo_pll_busy" "0,1" bitfld.long 0x0 16. "LDO_PLL_AI_TOGGLE,ldo_pll_ai_toggle" "0,1" bitfld.long 0x0 1. "LDO_PLL_CONTROL_MODE,LDO_PLL_CONTROL_MODE" "0: SW Control,1: HW Control" newline bitfld.long 0x0 0. "LDO_PLL_ENABLE,LDO_PLL_ENABLE" "0,1" group.long 0x550++0x3 line.long 0x0 "PMU_BIAS_CTRL,PMU_BIAS_CTRL_REGISTER" bitfld.long 0x0 14. "WB_VDD_SEL_1P8,wb_vdd_sel_1p8" "0: VDD_LV1,1: VDD_LV2" hexmask.long.word 0x0 0.--12. 1. "WB_CFG_1P8,wb_cfg_1p8" group.long 0x560++0x3 line.long 0x0 "PMU_BIAS_CTRL2,PMU_BIAS_CTRL2_REGISTER" rbitfld.long 0x0 26. "WB_OK,Digital Output pin." "0,1" rbitfld.long 0x0 25. "WB_TST_DIG_OUT,Digital output" "0,1" bitfld.long 0x0 24. "WB_EN,wb_en" "0,1" newline bitfld.long 0x0 23. "RBB_LPSR_CONTROL_MODE,RBB_LPSR_CONTROL_MODE" "0: SW Control,1: HW Control" bitfld.long 0x0 22. "RBB_SOC_CONTROL_MODE,RBB_SOC_CONTROL_MODE" "0: SW Control,1: HW Control" hexmask.long.byte 0x0 13.--20. 1. "WB_ADJ_1P8,wb_adj_1p8" newline bitfld.long 0x0 10.--12. "WB_PWR_SW_EN_1P8,MODSEL_wb_tst_md_1p8" "?,?,2: BB,?,4: BB,?,?,?" hexmask.long.word 0x0 1.--9. 1. "WB_TST_MD,TMOD_wb_tst_md_1p8" group.long 0x570++0x3 line.long 0x0 "PMU_REF_CTRL,PMU_REF_CTRL_REGISTER" bitfld.long 0x0 4. "EN_PLL_VOL_REF_BUFFER,en_pll_vol_ref_buffer" "0,1" bitfld.long 0x0 3. "REF_CONTROL_MODE,REF_CONTROL_MODE" "0: SW Control,1: HW Control" bitfld.long 0x0 2. "REF_ENABLE,REF_ENABLE" "0,1" newline rbitfld.long 0x0 1. "REF_AI_BUSY,ref_ai_busy" "0,1" bitfld.long 0x0 0. "REF_AI_TOGGLE,ref_ai_toggle" "0,1" group.long 0x580++0x3 line.long 0x0 "PMU_POWER_DETECT_CTRL,PMU_POWER_DETECT_CTRL_REGISTER" bitfld.long 0x0 8. "CKGB_LPSR1P0,ckgb_lpsr1p0" "0,1" group.long 0x600++0x3 line.long 0x0 "LDO_PLL_ENABLE_SP,LDO_PLL_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT6" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x610++0x3 line.long 0x0 "LDO_LPSR_ANA_ENABLE_SP,LDO_LPSR_ANA_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT6" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x620++0x3 line.long 0x0 "LDO_LPSR_ANA_LP_MODE_SP,LDO_LPSR_ANA_LP_MODE_SP_REGISTER" bitfld.long 0x0 15. "LP_MODE_SETPONIT15,LP_MODE_SETPOINT15" "0: LP,1: HP" bitfld.long 0x0 14. "LP_MODE_SETPONIT14,LP_MODE_SETPOINT14" "0: LP,1: HP" bitfld.long 0x0 13. "LP_MODE_SETPONIT13,LP_MODE_SETPOINT13" "0: LP,1: HP" newline bitfld.long 0x0 12. "LP_MODE_SETPONIT12,LP_MODE_SETPOINT12" "0: LP,1: HP" bitfld.long 0x0 11. "LP_MODE_SETPONIT11,LP_MODE_SETPOINT11" "0: LP,1: HP" bitfld.long 0x0 10. "LP_MODE_SETPONIT10,LP_MODE_SETPOINT10" "0: LP,1: HP" newline bitfld.long 0x0 9. "LP_MODE_SETPONIT9,LP_MODE_SETPOINT9" "0: LP,1: HP" bitfld.long 0x0 8. "LP_MODE_SETPONIT8,LP_MODE_SETPOINT8" "0: LP,1: HP" bitfld.long 0x0 7. "LP_MODE_SETPONIT7,LP_MODE_SETPOINT7" "0: LP,1: HP" newline bitfld.long 0x0 6. "LP_MODE_SETPONIT6,LP_MODE_SETPOINT6" "0: LP,1: HP" bitfld.long 0x0 5. "LP_MODE_SETPONIT5,LP_MODE_SETPOINT5" "0: LP,1: HP" bitfld.long 0x0 4. "LP_MODE_SETPONIT4,LP_MODE_SETPOINT4" "0: LP,1: HP" newline bitfld.long 0x0 3. "LP_MODE_SETPONIT3,LP_MODE_SETPOINT3" "0: LP,1: HP" bitfld.long 0x0 2. "LP_MODE_SETPONIT2,LP_MODE_SETPOINT2" "0: LP,1: HP" bitfld.long 0x0 1. "LP_MODE_SETPOINT1,LP_MODE_SETPOINT1" "0: LP,1: HP" newline bitfld.long 0x0 0. "LP_MODE_SETPOINT0,LP_MODE_SETPOINT0" "0: LP,1: HP" group.long 0x630++0x3 line.long 0x0 "LDO_LPSR_ANA_TRACKING_EN_SP,LDO_LPSR_ANA_TRACKING_EN_SP_REGISTER" bitfld.long 0x0 15. "TRACKING_EN_SETPOINT15,TRACKING_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "TRACKING_EN_SETPOINT14,TRACKING_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "TRACKING_EN_SETPOINT13,TRACKING_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "TRACKING_EN_SETPOINT12,TRACKING_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "TRACKING_EN_SETPOINT11,TRACKING_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "TRACKING_EN_SETPOINT10,TRACKING_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "TRACKING_EN_SETPOINT9,TRACKING_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "TRACKING_EN_SETPOINT8,TRACKING_EN_SETPOINT8" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "TRACKING_EN_SETPOINT7,TRACKING_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "TRACKING_EN_SETPOINT6,TRACKING_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "TRACKING_EN_SETPOINT5,TRACKING_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "TRACKING_EN_SETPOINT4,TRACKING_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "TRACKING_EN_SETPOINT3,TRACKING_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "TRACKING_EN_SETPOINT2,TRACKING_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "TRACKING_EN_SETPOINT1,TRACKING_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "TRACKING_EN_SETPOINT0,TRACKING_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x640++0x3 line.long 0x0 "LDO_LPSR_ANA_BYPASS_EN_SP,LDO_LPSR_ANA_BYPASS_EN_SP_REGISTER" bitfld.long 0x0 15. "BYPASS_EN_SETPOINT15,BYPASS_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "BYPASS_EN_SETPOINT14,BYPASS_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "BYPASS_EN_SETPOINT13,BYPASS_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "BYPASS_EN_SETPOINT12,BYPASS_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "BYPASS_EN_SETPOINT11,BYPASS_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "BYPASS_EN_SETPOINT10,BYPASS_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "BYPASS_EN_SETPOINT9,BYPASS_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "BYPASS_EN_SETPOINT8,BYPASS_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "BYPASS_EN_SETPOINT7,BYPASS_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "BYPASS_EN_SETPOINT6,BYPASS_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "BYPASS_EN_SETPOINT5,BYPASS_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "BYPASS_EN_SETPOINT4,BYPASS_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "BYPASS_EN_SETPOINT3,BYPASS_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "BYPASS_EN_SETPOINT2,BYPASS_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "BYPASS_EN_SETPOINT1,BYPASS_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "BYPASS_EN_SETPOINT0,BYPASS_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x650++0x3 line.long 0x0 "LDO_LPSR_ANA_STBY_EN_SP,LDO_LPSR_ANA_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,STBY_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,STBY_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,STBY_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,STBY_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,STBY_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,STBY_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,STBY_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,STBY_EN_SETPOINT8" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,STBY_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,STBY_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,STBY_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,STBY_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,STBY_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,STBY_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,STBY_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,STBY_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x660++0x3 line.long 0x0 "LDO_LPSR_DIG_ENABLE_SP,LDO_LPSR_DIG_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT6" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x670++0x3 line.long 0x0 "LDO_LPSR_DIG_TRG_SP0,LDO_LPSR_DIG_TRG_SP0_REGISTER" hexmask.long.byte 0x0 24.--31. 1. "VOLTAGE_SETPOINT3,VOLTAGE_SETPOINT3" hexmask.long.byte 0x0 16.--23. 1. "VOLTAGE_SETPOINT2,VOLTAGE_SETPOINT2" hexmask.long.byte 0x0 8.--15. 1. "VOLTAGE_SETPOINT1,VOLTAGE_SETPOINT1" newline hexmask.long.byte 0x0 0.--7. 1. "VOLTAGE_SETPOINT0,VOLTAGE_SETPOINT0" group.long 0x680++0x3 line.long 0x0 "LDO_LPSR_DIG_TRG_SP1,LDO_LPSR_DIG_TRG_SP1_REGISTER" hexmask.long.byte 0x0 24.--31. 1. "VOLTAGE_SETPOINT7,VOLTAGE_SETPOINT7" hexmask.long.byte 0x0 16.--23. 1. "VOLTAGE_SETPOINT6,VOLTAGE_SETPOINT6" hexmask.long.byte 0x0 8.--15. 1. "VOLTAGE_SETPOINT5,VOLTAGE_SETPOINT5" newline hexmask.long.byte 0x0 0.--7. 1. "VOLTAGE_SETPOINT4,VOLTAGE_SETPOINT4" group.long 0x690++0x3 line.long 0x0 "LDO_LPSR_DIG_TRG_SP2,LDO_LPSR_DIG_TRG_SP2_REGISTER" hexmask.long.byte 0x0 24.--31. 1. "VOLTAGE_SETPOINT11,VOLTAGE_SETPOINT11" hexmask.long.byte 0x0 16.--23. 1. "VOLTAGE_SETPOINT10,VOLTAGE_SETPOINT10" hexmask.long.byte 0x0 8.--15. 1. "VOLTAGE_SETPOINT9,VOLTAGE_SETPOINT9" newline hexmask.long.byte 0x0 0.--7. 1. "VOLTAGE_SETPOINT8,VOLTAGE_SETPOINT8" group.long 0x6A0++0x3 line.long 0x0 "LDO_LPSR_DIG_TRG_SP3,LDO_LPSR_DIG_TRG_SP3_REGISTER" hexmask.long.byte 0x0 24.--31. 1. "VOLTAGE_SETPOINT15,VOLTAGE_SETPOINT15" hexmask.long.byte 0x0 16.--23. 1. "VOLTAGE_SETPOINT14,VOLTAGE_SETPOINT14" hexmask.long.byte 0x0 8.--15. 1. "VOLTAGE_SETPOINT13,VOLTAGE_SETPOINT13" newline hexmask.long.byte 0x0 0.--7. 1. "VOLTAGE_SETPOINT12,VOLTAGE_SETPOINT12" group.long 0x6B0++0x3 line.long 0x0 "LDO_LPSR_DIG_LP_MODE_SP,LDO_LPSR_DIG_LP_MODE_SP_REGISTER" bitfld.long 0x0 15. "LP_MODE_SETPOINT15,LP_MODE_SETPOINT15" "0: LP,1: HP" bitfld.long 0x0 14. "LP_MODE_SETPOINT14,LP_MODE_SETPOINT14" "0: LP,1: HP" bitfld.long 0x0 13. "LP_MODE_SETPOINT13,LP_MODE_SETPOINT13" "0: LP,1: HP" newline bitfld.long 0x0 12. "LP_MODE_SETPOINT12,LP_MODE_SETPOINT12" "0: LP,1: HP" bitfld.long 0x0 11. "LP_MODE_SETPOINT11,LP_MODE_SETPOINT11" "0: LP,1: HP" bitfld.long 0x0 10. "LP_MODE_SETPOINT10,LP_MODE_SETPOINT10" "0: LP,1: HP" newline bitfld.long 0x0 9. "LP_MODE_SETPOINT9,LP_MODE_SETPOINT9" "0: LP,1: HP" bitfld.long 0x0 8. "LP_MODE_SETPOINT8,LP_MODE_SETPOINT8" "0: LP,1: HP" bitfld.long 0x0 7. "LP_MODE_SETPOINT7,LP_MODE_SETPOINT7" "0: LP,1: HP" newline bitfld.long 0x0 6. "LP_MODE_SETPOINT6,LP_MODE_SETPOINT6" "0: LP,1: HP" bitfld.long 0x0 5. "LP_MODE_SETPOINT5,LP_MODE_SETPOINT5" "0: LP,1: HP" bitfld.long 0x0 4. "LP_MODE_SETPOINT4,LP_MODE_SETPOINT4" "0: LP,1: HP" newline bitfld.long 0x0 3. "LP_MODE_SETPOINT3,LP_MODE_SETPOINT3" "0: LP,1: HP" bitfld.long 0x0 2. "LP_MODE_SETPOINT2,LP_MODE_SETPOINT2" "0: LP,1: HP" bitfld.long 0x0 1. "LP_MODE_SETPOINT1,LP_MODE_SETPOINT1" "0: LP,1: HP" newline bitfld.long 0x0 0. "LP_MODE_SETPOINT0,LP_MODE_SETPOINT0" "0: LP,1: HP" group.long 0x6C0++0x3 line.long 0x0 "LDO_LPSR_DIG_TRACKING_EN_SP,LDO_LPSR_DIG_TRACKING_EN_SP_REGISTER" bitfld.long 0x0 15. "TRACKING_EN_SETPOINT15,TRACKING_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "TRACKING_EN_SETPOINT14,TRACKING_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "TRACKING_EN_SETPOINT13,TRACKING_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "TRACKING_EN_SETPOINT12,TRACKING_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "TRACKING_EN_SETPOINT11,TRACKING_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "TRACKING_EN_SETPOINT10,TRACKING_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "TRACKING_EN_SETPOINT9,TRACKING_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "TRACKING_EN_SETPOINT8,TRACKING_EN_SETPOINT8" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "TRACKING_EN_SETPOINT7,TRACKING_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "TRACKING_EN_SETPOINT6,TRACKING_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "TRACKING_EN_SETPOINT5,TRACKING_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "TRACKING_EN_SETPOINT4,TRACKING_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "TRACKING_EN_SETPOINT3,TRACKING_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "TRACKING_EN_SETPOINT2,TRACKING_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "TRACKING_EN_SETPOINT1,TRACKING_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "TRACKING_EN_SETPOINT0,TRACKING_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x6D0++0x3 line.long 0x0 "LDO_LPSR_DIG_BYPASS_EN_SP,LDO_LPSR_DIG_BYPASS_EN_SP_REGISTER" bitfld.long 0x0 15. "BYPASS_EN_SETPOINT15,BYPASS_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "BYPASS_EN_SETPOINT14,BYPASS_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "BYPASS_EN_SETPOINT13,BYPASS_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "BYPASS_EN_SETPOINT12,BYPASS_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "BYPASS_EN_SETPOINT11,BYPASS_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "BYPASS_EN_SETPOINT10,BYPASS_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "BYPASS_EN_SETPOINT9,BYPASS_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "BYPASS_EN_SETPOINT8,BYPASS_EN_SETPOINT8" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "BYPASS_EN_SETPOINT7,BYPASS_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "BYPASS_EN_SETPOINT6,BYPASS_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "BYPASS_EN_SETPOINT5,BYPASS_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "BYPASS_EN_SETPOINT4,BYPASS_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "BYPASS_EN_SETPOINT3,BYPASS_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "BYPASS_EN_SETPOINT2,BYPASS_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "BYPASS_EN_SETPOINT1,BYPASS_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "BYPASS_EN_SETPOINT0,BYPASS_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x6E0++0x3 line.long 0x0 "LDO_LPSR_DIG_STBY_EN_SP,LDO_LPSR_DIG_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,STBY_EN_SETPOINT15" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,STBY_EN_SETPOINT14" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,STBY_EN_SETPOINT13" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,STBY_EN_SETPOINT12" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,STBY_EN_SETPOINT11" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,STBY_EN_SETPOINT10" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,STBY_EN_SETPOINT9" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,STBY_EN_SETPOINT8" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,STBY_EN_SETPOINT7" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,STBY_EN_SETPOINT6" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,STBY_EN_SETPOINT5" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,STBY_EN_SETPOINT4" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,STBY_EN_SETPOINT3" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,STBY_EN_SETPOINT2" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,STBY_EN_SETPOINT1" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,STBY_EN_SETPOINT0" "0: Disabled,1: Enabled" group.long 0x6F0++0x3 line.long 0x0 "BANDGAP_ENABLE_SP,BANDGAP_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x710++0x3 line.long 0x0 "RBB_SOC_ENABLE_SP,RBB_SOC_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT6" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x720++0x3 line.long 0x0 "RBB_LPSR_ENABLE_SP,RBB_LPSR_ENABLE_SP_REGISTER" bitfld.long 0x0 15. "ON_OFF_SETPOINT15,ON_OFF_SETPOINT15" "0: ON,1: OFF" bitfld.long 0x0 14. "ON_OFF_SETPOINT14,ON_OFF_SETPOINT14" "0: ON,1: OFF" bitfld.long 0x0 13. "ON_OFF_SETPOINT13,ON_OFF_SETPOINT13" "0: ON,1: OFF" newline bitfld.long 0x0 12. "ON_OFF_SETPOINT12,ON_OFF_SETPOINT12" "0: ON,1: OFF" bitfld.long 0x0 11. "ON_OFF_SETPOINT11,ON_OFF_SETPOINT11" "0: ON,1: OFF" bitfld.long 0x0 10. "ON_OFF_SETPOINT10,ON_OFF_SETPOINT10" "0: ON,1: OFF" newline bitfld.long 0x0 9. "ON_OFF_SETPOINT9,ON_OFF_SETPOINT9" "0: ON,1: OFF" bitfld.long 0x0 8. "ON_OFF_SETPOINT8,ON_OFF_SETPOINT8" "0: ON,1: OFF" bitfld.long 0x0 7. "ON_OFF_SETPOINT7,ON_OFF_SETPOINT7" "0: ON,1: OFF" newline bitfld.long 0x0 6. "ON_OFF_SETPOINT6,ON_OFF_SETPOINT6" "0: ON,1: OFF" bitfld.long 0x0 5. "ON_OFF_SETPOINT5,ON_OFF_SETPOINT5" "0: ON,1: OFF" bitfld.long 0x0 4. "ON_OFF_SETPOINT4,ON_OFF_SETPOINT4" "0: ON,1: OFF" newline bitfld.long 0x0 3. "ON_OFF_SETPOINT3,ON_OFF_SETPOINT3" "0: ON,1: OFF" bitfld.long 0x0 2. "ON_OFF_SETPOINT2,ON_OFF_SETPOINT2" "0: ON,1: OFF" bitfld.long 0x0 1. "ON_OFF_SETPOINT1,ON_OFF_SETPOINT1" "0: ON,1: OFF" newline bitfld.long 0x0 0. "ON_OFF_SETPOINT0,ON_OFF_SETPOINT0" "0: ON,1: OFF" group.long 0x730++0x3 line.long 0x0 "BANDGAP_STBY_EN_SP,BANDGAP_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,STBY_EN_SETPOINT" "0: Disabled,1: Enabled" group.long 0x740++0x3 line.long 0x0 "PLL_LDO_STBY_EN_SP,PLL_LDO_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,Standby mode" "0: Disabled,1: Enabled" group.long 0x760++0x3 line.long 0x0 "RBB_SOC_STBY_EN_SP,RBB_SOC_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,Standby mode" "0: Disabled,1: Enabled" group.long 0x770++0x3 line.long 0x0 "RBB_LPSR_STBY_EN_SP,RBB_LPSR_STBY_EN_SP_REGISTER" bitfld.long 0x0 15. "STBY_EN_SETPOINT15,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 14. "STBY_EN_SETPOINT14,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 13. "STBY_EN_SETPOINT13,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 12. "STBY_EN_SETPOINT12,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 11. "STBY_EN_SETPOINT11,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 10. "STBY_EN_SETPOINT10,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 9. "STBY_EN_SETPOINT9,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 8. "STBY_EN_SETPOINT8,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 7. "STBY_EN_SETPOINT7,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 6. "STBY_EN_SETPOINT6,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 5. "STBY_EN_SETPOINT5,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 4. "STBY_EN_SETPOINT4,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 3. "STBY_EN_SETPOINT3,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 2. "STBY_EN_SETPOINT2,Standby mode" "0: Disabled,1: Enabled" bitfld.long 0x0 1. "STBY_EN_SETPOINT1,Standby mode" "0: Disabled,1: Enabled" newline bitfld.long 0x0 0. "STBY_EN_SETPOINT0,Standby mode" "0: Disabled,1: Enabled" group.long 0x790++0x3 line.long 0x0 "RBB_LPSR_CONFIGURE,RBB_LPSR_CONFIGURE_REGISTER" bitfld.long 0x0 11.--13. "REGULATOR_STRENGTH,regulator_strength" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--10. "OSCILLATOR_BITS,oscillator_bits" "0,1,2,3,4,5,6,7" hexmask.long.byte 0x0 4.--7. 1. "WB_CFG_NW,wb_cfg_nw" newline hexmask.long.byte 0x0 0.--3. 1. "WB_CFG_PW,wb_cfg_pw" group.long 0x7A0++0x3 line.long 0x0 "RBB_SOC_CONFIGURE,RBB_SOC_CONFIGURE_REGISTER" bitfld.long 0x0 11.--13. "REGULATOR_STRENGTH,regulator_strength" "0,1,2,3,4,5,6,7" bitfld.long 0x0 8.--10. "OSCILLATOR_BITS,oscillator_bits" "0,1,2,3,4,5,6,7" hexmask.long.byte 0x0 4.--7. 1. "WB_CFG_NW,wb_cfg_nw" newline hexmask.long.byte 0x0 0.--3. 1. "WB_CFG_PW,wb_cfg_pw" rgroup.long 0x7B0++0x3 line.long 0x0 "REFTOP_OTP_TRIM_VALUE,REFTOP_OTP_TRIM_VALUE_REGISTER" bitfld.long 0x0 6. "REFTOP_TRIM_EN,REFTOP_TRIM_EN" "0,1" bitfld.long 0x0 3.--5. "REFTOP_VBGADJ,REFTOP_VBGADJ" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "REFTOP_IBZTCADJ,REFTOP_IBZTCADJ" "0,1,2,3,4,5,6,7" rgroup.long 0x7D0++0x3 line.long 0x0 "LPSR_1P8_LDO_OTP_TRIM_VALUE,LPSR_1P8_LDO_OTP_TRIM_VALUE_REGISTER" bitfld.long 0x0 2. "LPSR_LDO_1P8_TRIM_EN,LPSR_LDO_1P8_TRIM_EN" "0,1" bitfld.long 0x0 0.--1. "LPSR_LDO_1P8_TRIM,LPSR_LDO_1P8_TRIM" "0,1,2,3" tree.end tree "ANADIG_TEMPSENSOR" base ad:0x40C84000 group.long 0x400++0x3 line.long 0x0 "TEMPSENSOR,Tempsensor Register" rbitfld.long 0x0 16. "TEMPSNS_AI_BUSY,AI Busy monitor" "0,1" bitfld.long 0x0 15. "TEMPSNS_AI_TOGGLE,AI toggle" "0,1" rgroup.long 0x430++0x3 line.long 0x0 "TEMPSNS_OTP_TRIM_VALUE,TEMPSNS_OTP_TRIM_VALUE_REGISTER" hexmask.long.word 0x0 10.--21. 1. "TEMPSNS_TEMP_VAL,Temperature Value at 25C" tree.end tree.end tree "AOI" base ad:0x0 tree "AOI1" base ad:0x400B8000 group.word 0x0++0xF line.word 0x0 "BFCRT010,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x0 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x0 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x0 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x0 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x0 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x0 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x0 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x0 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x2 "BFCRT230,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0x2 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x2 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x2 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x2 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x2 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x2 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x2 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x2 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x4 "BFCRT011,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x4 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x4 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x4 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x4 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x4 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x4 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x4 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x4 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x6 "BFCRT231,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0x6 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x6 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x6 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x6 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x6 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x6 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x6 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x6 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x8 "BFCRT012,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x8 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x8 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x8 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x8 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x8 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x8 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x8 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x8 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xA "BFCRT232,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0xA 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xA 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xA 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xA 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xA 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xA 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xA 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xA 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xC "BFCRT013,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0xC 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xC 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xC 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xC 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xC 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xC 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xC 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xC 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xE "BFCRT233,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0xE 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xE 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xE 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xE 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xE 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xE 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xE 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xE 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." tree.end tree "AOI2" base ad:0x400BC000 group.word 0x0++0xF line.word 0x0 "BFCRT010,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x0 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x0 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x0 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x0 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x0 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x0 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x0 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x0 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x2 "BFCRT230,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0x2 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x2 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x2 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x2 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x2 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x2 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x2 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x2 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x4 "BFCRT011,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x4 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x4 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x4 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x4 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x4 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x4 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x4 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x4 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x6 "BFCRT231,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0x6 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x6 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x6 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x6 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x6 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x6 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x6 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x6 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0x8 "BFCRT012,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0x8 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x8 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x8 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x8 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0x8 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0x8 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0x8 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0x8 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xA "BFCRT232,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0xA 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xA 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xA 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xA 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xA 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xA 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xA 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xA 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xC "BFCRT013,Boolean Function Term 0 and 1 Configuration Register for EVENTn" bitfld.word 0xC 14.--15. "PT0_AC,Product term 0 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xC 12.--13. "PT0_BC,Product term 0 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xC 10.--11. "PT0_CC,Product term 0 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xC 8.--9. "PT0_DC,Product term 0 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xC 6.--7. "PT1_AC,Product term 1 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xC 4.--5. "PT1_BC,Product term 1 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xC 2.--3. "PT1_CC,Product term 1 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xC 0.--1. "PT1_DC,Product term 1 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." line.word 0xE "BFCRT233,Boolean Function Term 2 and 3 Configuration Register for EVENTn" bitfld.word 0xE 14.--15. "PT2_AC,Product term 2 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xE 12.--13. "PT2_BC,Product term 2 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xE 10.--11. "PT2_CC,Product term 2 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xE 8.--9. "PT2_DC,Product term 2 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." newline bitfld.word 0xE 6.--7. "PT3_AC,Product term 3 A input configuration" "0: Force the A input in this product term to a..,1: Pass the A input in this product term,2: Complement the A input in this product term,3: Force the A input in this product term to a.." bitfld.word 0xE 4.--5. "PT3_BC,Product term 3 B input configuration" "0: Force the B input in this product term to a..,1: Pass the B input in this product term,2: Complement the B input in this product term,3: Force the B input in this product term to a.." newline bitfld.word 0xE 2.--3. "PT3_CC,Product term 3 C input configuration" "0: Force the C input in this product term to a..,1: Pass the C input in this product term,2: Complement the C input in this product term,3: Force the C input in this product term to a.." bitfld.word 0xE 0.--1. "PT3_DC,Product term 3 D input configuration" "0: Force the D input in this product term to a..,1: Pass the D input in this product term,2: Complement the D input in this product term,3: Force the D input in this product term to a.." tree.end tree.end tree "ASRC" base ad:0x40414000 group.long 0x0++0x7 line.long 0x0 "ASRCTR,ASRC Control Register" bitfld.long 0x0 22. "ATSC,ATSC" "0: Pair C does not automatically update its..,1: Pair C automatically updates its pre-processing.." newline bitfld.long 0x0 21. "ATSB,ATSB" "0: Pair B does not automatically update its..,1: Pair B automatically updates its pre-processing.." newline bitfld.long 0x0 20. "ATSA,ATSA" "0: Pair A does not automatically update its..,1: Pair A automatically updates its pre-processing.." newline bitfld.long 0x0 18. "USRC,USRC" "0: Do not use ratio as the input to ASRC for pair C,1: Use ratio as the input to ASRC for pair C" newline bitfld.long 0x0 17. "IDRC,IDRC" "0: ASRC internal measured ratio is used,1: Ideal ratio from the interface register ASRIDRHC.." newline bitfld.long 0x0 16. "USRB,USRB" "0: Do not use ratio as the input to ASRC for pair B,1: Use ratio as the input to ASRC for pair B" newline bitfld.long 0x0 15. "IDRB,IDRB" "0: ASRC internal measured ratio is used,1: Ideal ratio from the interface register ASRIDRHB.." newline bitfld.long 0x0 14. "USRA,USRA" "0: Do not use ratio as the input to ASRC for pair A,1: Use ratio as the input to ASRC for pair A" newline bitfld.long 0x0 13. "IDRA,IDRA" "0: ASRC internal measured ratio is used,1: Ideal ratio from the interface register ASRIDRHA.." newline bitfld.long 0x0 4. "SRST,SRST" "0: ASRC Software reset cleared,1: ASRC Software reset generated. NOTE: This is a.." newline bitfld.long 0x0 3. "ASREC,ASREC" "0: operation of conversion C is disabled,1: operation of conversion C is enabled" newline bitfld.long 0x0 2. "ASREB,ASREB" "0: operation of conversion B is disabled,1: operation of conversion B is enabled" newline bitfld.long 0x0 1. "ASREA,ASREA" "0: operation of conversion A is disabled,1: operation of conversion A is enabled" newline bitfld.long 0x0 0. "ASRCEN,ASRCEN" "0: operation of ASRC disabled,1: operation ASRC is enabled" line.long 0x4 "ASRIER,ASRC Interrupt Enable Register" bitfld.long 0x4 7. "AFPWE,AFPWE" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 6. "AOLIE,AOLIE" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 5. "ADOEC,ADOEC" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 4. "ADOEB,ADOEB" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 3. "ADOEA,ADOEA" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 2. "ADIEC,ADIEC" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 1. "ADIEB,ADIEB" "0: interrupt disabled,1: interrupt enabled" newline bitfld.long 0x4 0. "ADIEA,ADIEA" "0: interrupt disabled,1: interrupt enabled" group.long 0xC++0x13 line.long 0x0 "ASRCNCR,ASRC Channel Number Configuration Register" hexmask.long.byte 0x0 8.--11. 1. "ANCC,ANCC" newline hexmask.long.byte 0x0 4.--7. 1. "ANCB,ANCB" newline hexmask.long.byte 0x0 0.--3. 1. "ANCA,ANCA" line.long 0x4 "ASRCFG,ASRC Filter Configuration Status Register" rbitfld.long 0x4 23. "INIRQC,INIRQC" "0: Initialization for Conversion Pair C not served,1: Initialization for Conversion Pair C served" newline rbitfld.long 0x4 22. "INIRQB,INIRQB" "0: Initialization for Conversion Pair B not served,1: Initialization for Conversion Pair B served" newline rbitfld.long 0x4 21. "INIRQA,INIRQA" "0: Initialization for Conversion Pair A not served,1: Initialization for Conversion Pair A served" newline bitfld.long 0x4 20. "NDPRC,NDPRC" "0: Use default parameters for RAM-stored..,1: Don't use default parameters for RAM-stored.." newline bitfld.long 0x4 19. "NDPRB,NDPRB" "0: Use default parameters for RAM-stored..,1: Don't use default parameters for RAM-stored.." newline bitfld.long 0x4 18. "NDPRA,NDPRA" "0: Use default parameters for RAM-stored..,1: Don't use default parameters for RAM-stored.." newline bitfld.long 0x4 16.--17. "POSTMODC,POSTMODC" "0: Select Upsampling-by-2 as defined in Signal..,1: Select Direct-Connection as defined in Signal..,2: Select Downsampling-by-2 as defined in Signal..,?" newline bitfld.long 0x4 14.--15. "PREMODC,PREMODC" "0: Select Upsampling-by-2,1: Select Direct-Connection,2: Select Downsampling-by-2,3: Select passthrough mode. In this case.." newline bitfld.long 0x4 12.--13. "POSTMODB,POSTMODB" "0: Select Upsampling-by-2,1: Select Direct-Connection,2: Select Downsampling-by-2,?" newline bitfld.long 0x4 10.--11. "PREMODB,PREMODB" "0: Select Upsampling-by-2,1: Select Direct-Connection,2: Select Downsampling-by-2,3: Select passthrough mode. In this case.." newline bitfld.long 0x4 8.--9. "POSTMODA,POSTMODA" "0: Select Upsampling-by-2,1: Select Direct-Connection,2: Select Downsampling-by-2,?" newline bitfld.long 0x4 6.--7. "PREMODA,PREMODA" "0: Select Upsampling-by-2,1: Select Direct-Connection,2: Select Downsampling-by-2,3: Select passthrough mode. In this case.." line.long 0x8 "ASRCSR,ASRC Clock Source Register" hexmask.long.byte 0x8 20.--23. 1. "AOCSC,AOCSC" newline hexmask.long.byte 0x8 16.--19. 1. "AOCSB,AOCSB" newline hexmask.long.byte 0x8 12.--15. 1. "AOCSA,AOCSA" newline hexmask.long.byte 0x8 8.--11. 1. "AICSC,AICSC" newline hexmask.long.byte 0x8 4.--7. 1. "AICSB,AICSB" newline hexmask.long.byte 0x8 0.--3. 1. "AICSA,AICSA" line.long 0xC "ASRCDR1,ASRC Clock Divider Register 1" bitfld.long 0xC 21.--23. "AOCDB,AOCDB" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 18.--20. "AOCPB,AOCPB" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 15.--17. "AOCDA,AOCDA" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 12.--14. "AOCPA,AOCPA" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 9.--11. "AICDB,AICDB" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 6.--8. "AICPB,AICPB" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 3.--5. "AICDA,AICDA" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 0.--2. "AICPA,AICPA" "0,1,2,3,4,5,6,7" line.long 0x10 "ASRCDR2,ASRC Clock Divider Register 2" bitfld.long 0x10 9.--11. "AOCDC,AOCDC" "0,1,2,3,4,5,6,7" newline bitfld.long 0x10 6.--8. "AOCPC,AOCPC" "0,1,2,3,4,5,6,7" newline bitfld.long 0x10 3.--5. "AICDC,AICDC" "0,1,2,3,4,5,6,7" newline bitfld.long 0x10 0.--2. "AICPC,AICPC" "0,1,2,3,4,5,6,7" rgroup.long 0x20++0x3 line.long 0x0 "ASRSTR,ASRC Status Register" bitfld.long 0x0 21. "DSLCNT,DSLCNT" "0: New DSL counter information is in the process of..,1: New DSL counter information is stored in the.." newline bitfld.long 0x0 20. "ATQOL,ATQOL" "0: Task queue FIFO logic is not oveloaded,1: Task queue FIFO logic is oveloaded" newline bitfld.long 0x0 19. "AOOLC,AOOLC" "0: Pair C output task is not oveloaded,1: Pair C output task is oveloaded" newline bitfld.long 0x0 18. "AOOLB,AOOLB" "0: Pair B output task is not oveloaded,1: Pair B output task is oveloaded" newline bitfld.long 0x0 17. "AOOLA,AOOLA" "0: Pair A output task is not oveloaded,1: Pair A output task is oveloaded" newline bitfld.long 0x0 16. "AIOLC,AIOLC" "0: Pair C input task is not oveloaded,1: Pair C input task is oveloaded" newline bitfld.long 0x0 15. "AIOLB,AIOLB" "0: Pair B input task is not oveloaded,1: Pair B input task is oveloaded" newline bitfld.long 0x0 14. "AIOLA,AIOLA" "0: Pair A input task is not oveloaded,1: Pair A input task is oveloaded" newline bitfld.long 0x0 13. "AODOC,AODOC" "0: No Overflow in Output data buffer C,1: Overflow in Output data buffer C" newline bitfld.long 0x0 12. "AODOB,AODOB" "0: No Overflow in Output data buffer B,1: Overflow in Output data buffer B" newline bitfld.long 0x0 11. "AODOA,AODOA" "0: No Overflow in Output data buffer A,1: Overflow in Output data buffer A" newline bitfld.long 0x0 10. "AIDUC,AIDUC" "0: No Underflow in Input data buffer C,1: Underflow in Input data buffer C" newline bitfld.long 0x0 9. "AIDUB,AIDUB" "0: No Underflow in Input data buffer B,1: Underflow in Input data buffer B" newline bitfld.long 0x0 8. "AIDUA,AIDUA" "0: No Underflow in Input data buffer A,1: Underflow in Input data buffer A" newline bitfld.long 0x0 7. "FPWT,FPWT" "0: ASRC is not in wait state,1: ASRC is in wait state" newline bitfld.long 0x0 6. "AOLE,AOLE" "0: No overload,1: Task rate is too high" newline bitfld.long 0x0 5. "AODFC,AODFC" "0: The threshold has not yet been met and no data..,1: When AODFC is set the ASRC generates data output.." newline bitfld.long 0x0 4. "AODFB,AODFB" "0: The threshold has not yet been met and no data..,1: When AODFB is set the ASRC generates data output.." newline bitfld.long 0x0 3. "AODFA,AODFA" "0: The threshold has not yet been met and no data..,1: When AODFA is set the ASRC generates data output.." newline bitfld.long 0x0 2. "AIDEC,AIDEC" "0: The threshold has been met and no data input C..,1: When AIDEC is set the ASRC generates data input.." newline bitfld.long 0x0 1. "AIDEB,AIDEB" "0: The threshold has been met and no data input B..,1: When AIDEB is set the ASRC generates data input.." newline bitfld.long 0x0 0. "AIDEA,AIDEA" "0: The threshold has been met and no data input A..,1: When AIDEA is set the ASRC generates data input.." repeat 5. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "ASRPM$1,ASRC Parameter Register n" hexmask.long.tbyte 0x0 0.--23. 1. "PARAMETER_VALUE,PARAMETER_VALUE" repeat.end group.long 0x54++0x3 line.long 0x0 "ASRTFR1,ASRC Task Queue FIFO Register 1" hexmask.long.byte 0x0 13.--19. 1. "TF_FILL,TF_FILL" newline hexmask.long.byte 0x0 6.--12. 1. "TF_BASE,TF_BASE" group.long 0x5C++0x3 line.long 0x0 "ASRCCR,ASRC Channel Counter Register" hexmask.long.byte 0x0 20.--23. 1. "ACOC,ACOC" newline hexmask.long.byte 0x0 16.--19. 1. "ACOB,ACOB" newline hexmask.long.byte 0x0 12.--15. 1. "ACOA,ACOA" newline hexmask.long.byte 0x0 8.--11. 1. "ACIC,ACIC" newline hexmask.long.byte 0x0 4.--7. 1. "ACIB,ACIB" newline hexmask.long.byte 0x0 0.--3. 1. "ACIA,ACIA" wgroup.long 0x60++0x3 line.long 0x0 "ASRDIA,ASRC Data Input Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" rgroup.long 0x64++0x3 line.long 0x0 "ASRDOA,ASRC Data Output Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" wgroup.long 0x68++0x3 line.long 0x0 "ASRDIB,ASRC Data Input Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" rgroup.long 0x6C++0x3 line.long 0x0 "ASRDOB,ASRC Data Output Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" wgroup.long 0x70++0x3 line.long 0x0 "ASRDIC,ASRC Data Input Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" rgroup.long 0x74++0x3 line.long 0x0 "ASRDOC,ASRC Data Output Register for Pair x" hexmask.long.tbyte 0x0 0.--23. 1. "DATA,DATA" group.long 0x80++0x23 line.long 0x0 "ASRIDRHA,ASRC Ideal Ratio for Pair A-High Part" hexmask.long.byte 0x0 0.--7. 1. "IDRATIOA_H,IDRATIOA_H" line.long 0x4 "ASRIDRLA,ASRC Ideal Ratio for Pair A -Low Part" hexmask.long.tbyte 0x4 0.--23. 1. "IDRATIOA_L,IDRATIOA_L" line.long 0x8 "ASRIDRHB,ASRC Ideal Ratio for Pair B-High Part" hexmask.long.byte 0x8 0.--7. 1. "IDRATIOB_H,IDRATIOB_H" line.long 0xC "ASRIDRLB,ASRC Ideal Ratio for Pair B-Low Part" hexmask.long.tbyte 0xC 0.--23. 1. "IDRATIOB_L,IDRATIOB_L" line.long 0x10 "ASRIDRHC,ASRC Ideal Ratio for Pair C-High Part" hexmask.long.byte 0x10 0.--7. 1. "IDRATIOC_H,IDRATIOC_H" line.long 0x14 "ASRIDRLC,ASRC Ideal Ratio for Pair C-Low Part" hexmask.long.tbyte 0x14 0.--23. 1. "IDRATIOC_L,IDRATIOC_L" line.long 0x18 "ASR76K,ASRC 76 kHz Period in terms of ASRC processing clock" hexmask.long.tbyte 0x18 0.--16. 1. "ASR76K,ASR76K" line.long 0x1C "ASR56K,ASRC 56 kHz Period in terms of ASRC processing clock" hexmask.long.tbyte 0x1C 0.--16. 1. "ASR56K,ASR56K" line.long 0x20 "ASRMCRA,ASRC Misc Control Register for Pair A" bitfld.long 0x20 23. "ZEROBUFA,ZEROBUFA" "0: Zeroize the buffer,1: Don't zeroize the buffer" newline bitfld.long 0x20 22. "EXTTHRSHA,EXTTHRSHA" "0: Use default thresholds.,1: Use external defined thresholds." newline bitfld.long 0x20 21. "BUFSTALLA,BUFSTALLA" "0: Don't stall Pair A conversion even in case of..,1: Stall Pair A conversion in case of near.." newline bitfld.long 0x20 20. "BYPASSPOLYA,BYPASSPOLYA" "0: Don't bypass polyphase filtering.,1: Bypass polyphase filtering." newline hexmask.long.byte 0x20 12.--17. 1. "OUTFIFO_THRESHOLDA,OUTFIFO_THRESHOLDA" newline bitfld.long 0x20 11. "RSYNIFA,RSYNIFA" "0: Do not touch ASRCCR[ACIA],1: Force ASRCCR[ACIA]=0" newline bitfld.long 0x20 10. "RSYNOFA,RSYNOFA" "0: Do not touch ASRCCR[ACOA],1: Force ASRCCR[ACOA]=0" newline hexmask.long.byte 0x20 0.--5. 1. "INFIFO_THRESHOLDA,INFIFO_THRESHOLDA" rgroup.long 0xA4++0x3 line.long 0x0 "ASRFSTA,ASRC FIFO Status Register for Pair A" bitfld.long 0x0 23. "OAFA,OAFA" "0: Output FIFO is not near full for Pair A,1: Output FIFO is near full for Pair A" newline hexmask.long.byte 0x0 12.--18. 1. "OUTFIFO_FILLA,OUTFIFO_FILLA" newline bitfld.long 0x0 11. "IAEA,IAEA" "0: Input FIFO is not near empty for Pair A,1: Input FIFO is near empty for Pair A" newline hexmask.long.byte 0x0 0.--6. 1. "INFIFO_FILLA,INFIFO_FILLA" group.long 0xA8++0x3 line.long 0x0 "ASRMCRB,ASRC Misc Control Register for Pair B" bitfld.long 0x0 23. "ZEROBUFB,ZEROBUFB" "0: Zeroize the buffer,1: Don't zeroize the buffer" newline bitfld.long 0x0 22. "EXTTHRSHB,EXTTHRSHB" "0: Use default thresholds.,1: Use external defined thresholds." newline bitfld.long 0x0 21. "BUFSTALLB,BUFSTALLB" "0: Don't stall Pair B conversion even in case of..,1: Stall Pair B conversion in case of near.." newline bitfld.long 0x0 20. "BYPASSPOLYB,BYPASSPOLYB" "0: Don't bypass polyphase filtering.,1: Bypass polyphase filtering." newline hexmask.long.byte 0x0 12.--17. 1. "OUTFIFO_THRESHOLDB,OUTFIFO_THRESHOLDB" newline bitfld.long 0x0 11. "RSYNIFB,RSYNIFB" "0: Do not touch ASRCCR[ACIB],1: Force ASRCCR[ACIB]=0" newline bitfld.long 0x0 10. "RSYNOFB,RSYNOFB" "0: Do not touch ASRCCR[ACOB],1: Force ASRCCR[ACOB]=0" newline hexmask.long.byte 0x0 0.--5. 1. "INFIFO_THRESHOLDB,INFIFO_THRESHOLDB" rgroup.long 0xAC++0x3 line.long 0x0 "ASRFSTB,ASRC FIFO Status Register for Pair B" bitfld.long 0x0 23. "OAFB,OAFB" "0: Output FIFO is not near full for Pair B,1: Output FIFO is near full for Pair B" newline hexmask.long.byte 0x0 12.--18. 1. "OUTFIFO_FILLB,OUTFIFO_FILLB" newline bitfld.long 0x0 11. "IAEB,IAEB" "0: Input FIFO is not near empty for Pair B,1: Input FIFO is near empty for Pair B" newline hexmask.long.byte 0x0 0.--6. 1. "INFIFO_FILLB,INFIFO_FILLB" group.long 0xB0++0x3 line.long 0x0 "ASRMCRC,ASRC Misc Control Register for Pair C" bitfld.long 0x0 23. "ZEROBUFC,ZEROBUFC" "0: Zeroize the buffer,1: Don't zeroize the buffer" newline bitfld.long 0x0 22. "EXTTHRSHC,EXTTHRSHC" "0: Use default thresholds.,1: Use external defined thresholds." newline bitfld.long 0x0 21. "BUFSTALLC,BUFSTALLC" "0: Don't stall Pair C conversion even in case of..,1: Stall Pair C conversion in case of near.." newline bitfld.long 0x0 20. "BYPASSPOLYC,BYPASSPOLYC" "0: Don't bypass polyphase filtering.,1: Bypass polyphase filtering." newline hexmask.long.byte 0x0 12.--17. 1. "OUTFIFO_THRESHOLDC,OUTFIFO_THRESHOLDC" newline bitfld.long 0x0 11. "RSYNIFC,RSYNIFC" "0: Do not touch ASRCCR[ACIC],1: Force ASRCCR[ACIC]=0" newline bitfld.long 0x0 10. "RSYNOFC,RSYNOFC" "0: Do not touch ASRCCR[ACOC],1: Force ASRCCR[ACOC]=0" newline hexmask.long.byte 0x0 0.--5. 1. "INFIFO_THRESHOLDC,INFIFO_THRESHOLDC" rgroup.long 0xB4++0x3 line.long 0x0 "ASRFSTC,ASRC FIFO Status Register for Pair C" bitfld.long 0x0 23. "OAFC,OAFC" "0: Output FIFO is not near full for Pair C,1: Output FIFO is near full for Pair C" newline hexmask.long.byte 0x0 12.--18. 1. "OUTFIFO_FILLC,OUTFIFO_FILLC" newline bitfld.long 0x0 11. "IAEC,IAEC" "0: Input FIFO is not near empty for Pair C,1: Input FIFO is near empty for Pair C" newline hexmask.long.byte 0x0 0.--6. 1. "INFIFO_FILLC,INFIFO_FILLC" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xC0)++0x3 line.long 0x0 "ASRMCR1$1,ASRC Misc Control Register 1 for Pair X" bitfld.long 0x0 9.--10. "IWD,IWD" "0: 24-bit audio data.,1: 16-bit audio data.,2: 8-bit audio data.,?" newline bitfld.long 0x0 8. "IMSB,IMSB" "0: LSB aligned.,1: MSB aligned." newline bitfld.long 0x0 2. "OMSB,OMSB" "0: LSB aligned.,1: MSB aligned." newline bitfld.long 0x0 1. "OSGN,OSGN" "0: No sign extension.,1: Sign extension." newline bitfld.long 0x0 0. "OW16,OW16" "0: 24-bit output data.,1: 16-bit output data" repeat.end tree.end tree "AUDIO_PLL" base ad:0x0 group.long 0x0++0x3F line.long 0x0 "CTRL0,Fractional PLL Control Register" bitfld.long 0x0 29. "BIAS_SELECT,BIAS_SELECT" "0: Used in SoCs with a bias current of 10uA,1: Used in SoCs with a bias current of 2uA" bitfld.long 0x0 25.--27. "POST_DIV_SEL,Post Divide Select" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,?,?" newline bitfld.long 0x0 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x0 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 17. "DITHER_EN,DITHER_EN" "0: Disable Dither,1: Enable Dither" bitfld.long 0x0 16. "BYPASS,BYPASS" "0: No Bypass,1: Bypass the PLL" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable the clock output,1: Enable the clock output" bitfld.long 0x0 14. "POWERUP,POWERUP" "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 13. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" bitfld.long 0x0 8. "ENABLE_ALT,ENABLE_ALT" "0: Disable the alternate clock output,1: Enable the alternate clock output which is the.." newline hexmask.long.byte 0x0 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x4 "CTRL0_SET,Fractional PLL Control Register" bitfld.long 0x4 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0x4 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x4 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0x4 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0x4 15. "ENABLE,ENABLE" "0,1" bitfld.long 0x4 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0x4 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0x4 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x4 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x8 "CTRL0_CLR,Fractional PLL Control Register" eventfld.long 0x8 29. "BIAS_SELECT,BIAS_SELECT" "0,1" eventfld.long 0x8 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 22. "PLL_REG_EN,PLL_REG_EN" "0,1" eventfld.long 0x8 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 17. "DITHER_EN,DITHER_EN" "0,1" eventfld.long 0x8 16. "BYPASS,BYPASS" "0,1" newline eventfld.long 0x8 15. "ENABLE,ENABLE" "0,1" eventfld.long 0x8 14. "POWERUP,POWERUP" "0,1" newline eventfld.long 0x8 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" eventfld.long 0x8 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x8 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0xC "CTRL0_TOG,Fractional PLL Control Register" bitfld.long 0xC 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0xC 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0xC 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0xC 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0xC 15. "ENABLE,ENABLE" "0,1" bitfld.long 0xC 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0xC 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0xC 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0xC 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x10 "SPREAD_SPECTRUM,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x10 16.--31. 1. "STOP,Stop" bitfld.long 0x10 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x10 0.--14. 1. "STEP,Step" line.long 0x14 "SPREAD_SPECTRUM_SET,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x14 16.--31. 1. "STOP,Stop" bitfld.long 0x14 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x14 0.--14. 1. "STEP,Step" line.long 0x18 "SPREAD_SPECTRUM_CLR,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x18 16.--31. 1. "STOP,Stop" eventfld.long 0x18 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x18 0.--14. 1. "STEP,Step" line.long 0x1C "SPREAD_SPECTRUM_TOG,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x1C 16.--31. 1. "STOP,Stop" bitfld.long 0x1C 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x1C 0.--14. 1. "STEP,Step" line.long 0x20 "NUMERATOR,Fractional PLL Numerator Control Register" hexmask.long 0x20 0.--29. 1. "NUM,Numerator" line.long 0x24 "NUMERATOR_SET,Fractional PLL Numerator Control Register" hexmask.long 0x24 0.--29. 1. "NUM,Numerator" line.long 0x28 "NUMERATOR_CLR,Fractional PLL Numerator Control Register" hexmask.long 0x28 0.--29. 1. "NUM,Numerator" line.long 0x2C "NUMERATOR_TOG,Fractional PLL Numerator Control Register" hexmask.long 0x2C 0.--29. 1. "NUM,Numerator" line.long 0x30 "DENOMINATOR,Fractional PLL Denominator Control Register" hexmask.long 0x30 0.--29. 1. "DENOM,Denominator" line.long 0x34 "DENOMINATOR_SET,Fractional PLL Denominator Control Register" hexmask.long 0x34 0.--29. 1. "DENOM,Denominator" line.long 0x38 "DENOMINATOR_CLR,Fractional PLL Denominator Control Register" hexmask.long 0x38 0.--29. 1. "DENOM,Denominator" line.long 0x3C "DENOMINATOR_TOG,Fractional PLL Denominator Control Register" hexmask.long 0x3C 0.--29. 1. "DENOM,Denominator" tree.end tree "CAAM" base ad:0x40440000 repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40440000 ad:0x40440020 ad:0x40440040 ad:0x40440060) tree "RMaAb[$1]" base $2 repeat 2. (list 0x0 0x1)(list 0x60100 0x60110) tree "RM[$1]" group.quad ($2)++0x7 line.quad 0x0 "RMA,RTIC Memory Block memoryBlock Address segment Register" hexmask.quad 0x0 0.--35. 1. "MEMBLKADDR,Memory Block Address" group.long ($2+0xC)++0x3 line.long 0x0 "RML,RTIC Memory Block memoryBlock Length segment Register" hexmask.long 0x0 0.--31. 1. "MEMBLKLEN,Memory Block Lengths" tree.end repeat.end tree.end repeat.end repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40440000 ad:0x40440100 ad:0x40440200 ad:0x40440300) tree "RaMD[$1]" base $2 repeat 2. (list 0x0 0x1)(list 0x60200 0x60280) tree "RaMD[$1]" repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "RMD_[$1],RTIC Memory Block memoryBlock endianness_full Endian Hash Result Word word" hexmask.long 0x0 0.--31. 1. "RTIC_Hash_Result,RTIC_Hash_Result" repeat.end tree.end repeat.end tree.end repeat.end base ad:0x40440000 group.long 0x4++0xB line.long 0x0 "MCFGR,Master Configuration Register" bitfld.long 0x0 31. "SWRST,Software Reset" "0,1" newline bitfld.long 0x0 30. "WDE,DECO Watchdog Enable" "0,1" newline bitfld.long 0x0 29. "WDF,Watchdog Fast" "0,1" newline bitfld.long 0x0 28. "DMA_RST,DMA Reset" "0,1" newline bitfld.long 0x0 27. "WRHD,Write Handoff Disable" "0,1" newline bitfld.long 0x0 19. "DWT,Double Word Transpose" "0,1" newline bitfld.long 0x0 16. "PS,Pointer Size. This bit determines the size of address pointers. (see Address pointers)." "0: Pointers fit in one 32-bit word (pointers are..,1: Pointers require two 32-bit words (pointers are.." newline hexmask.long.byte 0x0 12.--15. 1. "ARCACHE,AXI Read Transaction Attributes" newline hexmask.long.byte 0x0 8.--11. 1. "AWCACHE,AXI Write Transaction Attributes" newline hexmask.long.byte 0x0 4.--7. 1. "AXIPIPE,AXI Pipeline Depth" newline bitfld.long 0x0 2. "LARGE_BURST,Enable Large Bursts" "0,1" newline rbitfld.long 0x0 0. "NORMAL_BURST,Normal Burst Size" "0: Aligned 32 byte burst size target,1: Aligned 64 byte burst size target" line.long 0x4 "PAGE0_SDID,Page 0 SDID Register" hexmask.long.word 0x4 0.--14. 1. "SDID,Security Domain Identifier" line.long 0x8 "SCFGR,Security Configuration Register" hexmask.long.byte 0x8 28.--31. 1. "MPCURVE,Manufacturing Protection Curve" newline bitfld.long 0x8 27. "MPPKRC,Manufacturing Protection Private Key Register Clear" "0,1" newline bitfld.long 0x8 26. "MPMRL,Manufacturing Protection Message Register Lock" "0,1" newline bitfld.long 0x8 15. "VIRT_EN,Virtualization enable" "0: Disable job ring virtualization,1: Enable job ring virtualization" newline bitfld.long 0x8 11. "LCK_TRNG,Lock TRNG Program Mode" "0,1" newline bitfld.long 0x8 9. "RNGSH0,Random Number Generator State Handle 0." "0: When RNGSH0 is 0 RNG DRNG State Handle 0 can be..,1: When RNGSH0 is 1 RNG DRNG State Handle 0 cannot.." newline bitfld.long 0x8 0.--1. "PRIBLOB,Private Blob" "0: Private secure boot software blobs,1: Private provisioning type 1 blobs,2: Private provisioning type 2 blobs,3: Normal operation blobs" repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40440010 ad:0x40440018 ad:0x40440020 ad:0x40440028) tree "JRaDID[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "JRDID_MS,Job Ring Job_Ring DID Register - most significant half" bitfld.long 0x0 31. "LDID,Lock DIDs" "0,1" bitfld.long 0x0 30. "USE_OUT,USE_OUT" "0,1" hexmask.long.word 0x0 19.--29. 1. "PRIM_ICID,Primary ICID" bitfld.long 0x0 17. "LAMTD,Lock AMTD" "0,1" bitfld.long 0x0 16. "AMTD,Allow Make Trusted Descriptor" "0,1" bitfld.long 0x0 15. "TZ_OWN,TrustZone SecureWorld" "0,1" hexmask.long.word 0x0 5.--14. 1. "SDID_MS,Security Domain Identifier most significant bits" bitfld.long 0x0 4. "PRIM_TZ,Primary TZ" "0,1" hexmask.long.byte 0x0 0.--3. 1. "PRIM_DID,Job Ring Owner's DID" line.long 0x4 "JRDID_LS,Job Ring Job_Ring DID Register - least significant half" hexmask.long.word 0x4 19.--29. 1. "OUT_ICID,Job Ring Output ICID" hexmask.long.byte 0x4 0.--3. 1. "OUT_DID,Output DID" tree.end repeat.end base ad:0x40440000 group.long 0x58++0xB line.long 0x0 "DEBUGCTL,Debug Control Register" rbitfld.long 0x0 17. "STOP_ACK,STOP_ACK will assert when the job queue controller acknowledges that it is stopped." "0,1" newline bitfld.long 0x0 16. "STOP,STOP is written to 1 to request that CAAM stop processing jobs" "0,1" line.long 0x4 "JRSTARTR,Job Ring Start Register" bitfld.long 0x4 3. "Start_JR3,Start Job Ring 3" "0: Stop Mode. The JR3DID register and the SMVBA..,1: Start Mode. The JR3DID register and the SMVBA.." newline bitfld.long 0x4 2. "Start_JR2,Start Job Ring 2" "0: Stop Mode. The JR2DID register and the SMVBA..,1: Start Mode. The JR2DID register and the SMVBA.." newline bitfld.long 0x4 1. "Start_JR1,Start Job Ring 1" "0: Stop Mode. The JR1DID register and the SMVBA..,1: Start Mode. The JR1DID register and the SMVBA.." newline bitfld.long 0x4 0. "Start_JR0,Start Job Ring 0" "0: Stop Mode. The JR0DID register and the SMVBA..,1: Start Mode. The JR0DID register and the SMVBA.." line.long 0x8 "RTIC_OWN,RTIC OWN Register" bitfld.long 0x8 31. "LCK,RTIC OWN Lock" "0,1" newline bitfld.long 0x8 4. "ROWN_TZ,RTIC Owner's TZ" "0,1" newline hexmask.long.byte 0x8 0.--3. 1. "ROWN_DID,RTIC Owner's DID" repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40440060 ad:0x40440068 ad:0x40440070 ad:0x40440078) tree "RTICaDID[$1]" base $2 group.long ($2+0x4)++0x3 line.long 0x0 "RTIC_DID,RTIC DID Register for Block RTIC_hash_block" hexmask.long.word 0x0 19.--29. 1. "RTIC_ICID,RTIC ICID" bitfld.long 0x0 4. "RTIC_TZ,RTIC_TZ" "0,1" hexmask.long.byte 0x0 0.--3. 1. "RTIC_DID,RTIC DID" tree.end repeat.end base ad:0x40440000 group.long 0x94++0x3 line.long 0x0 "DECORSR,DECO Request Source Register" rbitfld.long 0x0 31. "VALID,Valid" "0,1" newline bitfld.long 0x0 0.--1. "JR,Job Ring number" "0,1,2,3" group.long 0x9C++0xB line.long 0x0 "DECORR,DECO Request Register" rbitfld.long 0x0 16. "DEN0,The job queue controller asserts this bit when permission is granted for the software to directly access DECO 0/CCB 0" "0,1" newline bitfld.long 0x0 0. "RQD0,This bit is set by software to request direct access to DECO 0/CCB 0" "0,1" line.long 0x4 "DECO0DID_MS,DECO0 DID Register - most significant half" bitfld.long 0x4 31. "LCK,Lock" "0,1" newline bitfld.long 0x4 4. "D_NS,DECO Owner's ns" "0,1" newline hexmask.long.byte 0x4 0.--3. 1. "DPRIM_DID,DECO Owner" line.long 0x8 "DECO0DID_LS,DECO0 DID Register - least significant half" bitfld.long 0x8 20. "DNONSEQ_NS,DECO NONSEQ NonSecure" "0,1" newline hexmask.long.byte 0x8 16.--19. 1. "DNSEQ_DID,DECO Non-SEQ DID" newline bitfld.long 0x8 4. "DSEQ_NS,DECO SEQ NonSecure" "0,1" newline hexmask.long.byte 0x8 0.--3. 1. "DSEQ_DID,DECO SEQ DID" group.long 0x120++0x3 line.long 0x0 "DAR,DECO Availability Register" bitfld.long 0x0 0. "NYA0,This bit is set by software to start polling for the availability of DECO 0" "0,1" wgroup.long 0x124++0x3 line.long 0x0 "DRR,DECO Reset Register" bitfld.long 0x0 0. "RST0,Software writes a 1 to this bit to initiate a soft reset of DECO 0" "0,1" repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40440184 ad:0x4044018C ad:0x40440194 ad:0x4044019C) tree "JRnSMVBAR[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "JRSMVBAR,Job Ring Job_Ring Secure Memory Virtual Base Address Register" hexmask.long 0x0 0.--31. 1. "SMVBA,Secure Memory Virtual Base Address" tree.end repeat.end base ad:0x40440000 group.long 0x220++0x3 line.long 0x0 "PBSL,Peak Bandwidth Smoothing Limit Register" hexmask.long.byte 0x0 0.--6. 1. "PBSL,Whenever the number of outstanding AXI read bursts exceeds the value programmed in this field the Job Rings will be prevented from issuing additional AXI reads" rgroup.long 0x240++0x13 line.long 0x0 "DMA0_AIDL_MAP_MS,DMA0_AIDL_MAP_MS" hexmask.long.byte 0x0 24.--31. 1. "AID7_BID,This field shows the CAAM Block ID that uses AXI ID 7." newline hexmask.long.byte 0x0 16.--23. 1. "AID6_BID,This field shows the CAAM Block ID that uses AXI ID 6." newline hexmask.long.byte 0x0 8.--15. 1. "AID5_BID,This field shows the CAAM Block ID that uses AXI ID 5." newline hexmask.long.byte 0x0 0.--7. 1. "AID4_BID,This field shows the CAAM Block ID that uses AXI ID 4." line.long 0x4 "DMA0_AIDL_MAP_LS,DMA0_AIDL_MAP_LS" hexmask.long.byte 0x4 24.--31. 1. "AID3_BID,This field shows the CAAM Block ID that uses AXI ID 3." newline hexmask.long.byte 0x4 16.--23. 1. "AID2_BID,This field shows the CAAM Block ID that uses AXI ID 2." newline hexmask.long.byte 0x4 8.--15. 1. "AID1_BID,This field shows the CAAM Block ID that uses AXI ID 1." newline hexmask.long.byte 0x4 0.--7. 1. "AID0_BID,This field shows the CAAM Block ID that uses AXI ID 0." line.long 0x8 "DMA0_AIDM_MAP_MS,DMA0_AIDM_MAP_MS" hexmask.long.byte 0x8 24.--31. 1. "AID15_BID,This field shows the CAAM Block ID that uses AXI ID 15." newline hexmask.long.byte 0x8 16.--23. 1. "AID14_BID,This field shows the CAAM Block ID that uses AXI ID 14." newline hexmask.long.byte 0x8 8.--15. 1. "AID13_BID,This field shows the CAAM Block ID that uses AXI ID 13." newline hexmask.long.byte 0x8 0.--7. 1. "AID12_BID,This field shows the CAAM Block ID that uses AXI ID 12." line.long 0xC "DMA0_AIDM_MAP_LS,DMA0_AIDM_MAP_LS" hexmask.long.byte 0xC 24.--31. 1. "AID11_BID,This field shows the CAAM Block ID that uses AXI ID 11." newline hexmask.long.byte 0xC 16.--23. 1. "AID10_BID,This field shows the CAAM Block ID that uses AXI ID 10." newline hexmask.long.byte 0xC 8.--15. 1. "AID9_BID,This field shows the CAAM Block ID that uses AXI ID 9." newline hexmask.long.byte 0xC 0.--7. 1. "AID8_BID,This field shows the CAAM Block ID that uses AXI ID 8." line.long 0x10 "DMA0_AID_ENB,DMA0 AXI ID Enable Register" bitfld.long 0x10 15. "AID15E,If AID15E=1 then AXI ID 15 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 14. "AID14E,If AID14E=1 then AXI ID 14 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 13. "AID13E,If AID13E=1 then AXI ID 13 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 12. "AID12E,If AID12E=1 then AXI ID 12 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 11. "AID11E,If AID11E=1 then AXI ID 11 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 10. "AID10E,If AID10E=1 then AXI ID 10 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 9. "AID9E,If AID9E=1 then AXI ID 9 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 8. "AID8E,If AID8E=1 then AXI ID 8 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 7. "AID7E,If AID7E=1 then AXI ID 7 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 6. "AID6E,If AID6E=1 then AXI ID 6 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 5. "AID5E,If AID5E=1 then AXI ID 5 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 4. "AID4E,If AID4E=1 then AXI ID 4 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 3. "AID3E,If AID3E=1 then AXI ID 3 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 2. "AID2E,If AID2E=1 then AXI ID 2 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 1. "AID1E,If AID1E=1 then AXI ID 1 is enabled for this DMA engine." "0,1" newline bitfld.long 0x10 0. "AID0E,If AID0E=1 then AXI ID 0 is enabled for this DMA engine." "0,1" group.quad 0x260++0x7 line.quad 0x0 "DMA0_ARD_TC,DMA0 AXI Read Timing Check Register" bitfld.quad 0x0 63. "ARTCE,AXI Read Timing Check Enable" "0,1" newline bitfld.quad 0x0 62. "ARCT,AXI Read Counter Test" "0,1" newline bitfld.quad 0x0 61. "ARTT,AXI Read Timer Test" "0,1" newline bitfld.quad 0x0 60. "ARTL,AXI Read Timer Last" "0,1" newline hexmask.quad.word 0x0 48.--59. 1. "ARL,AXI Read Limit" newline hexmask.quad.tbyte 0x0 24.--43. 1. "ARLC,AXI Read Late Count" newline hexmask.quad.tbyte 0x0 0.--19. 1. "ARSC,AXI Read Sample Count" group.long 0x26C++0x3 line.long 0x0 "DMA0_ARD_LAT,DMA0 Read Timing Check Latency Register" hexmask.long 0x0 0.--31. 1. "SARL,Sum of the AXI Read Latencies" group.quad 0x270++0x7 line.quad 0x0 "DMA0_AWR_TC,DMA0 AXI Write Timing Check Register" bitfld.quad 0x0 63. "AWTCE,AXI Write Timing Check Enable" "0,1" newline bitfld.quad 0x0 62. "AWCT,AXI Write Counter Test" "0,1" newline bitfld.quad 0x0 61. "AWTT,AXI Write Timer Test" "0,1" newline hexmask.quad.word 0x0 48.--59. 1. "AWL,AXI Write Limit" newline hexmask.quad.tbyte 0x0 24.--43. 1. "AWLC,AXI Write Late Count" newline hexmask.quad.tbyte 0x0 0.--19. 1. "AWSC,AXI Write Sample Count" group.long 0x27C++0x3 line.long 0x0 "DMA0_AWR_LAT,DMA0 Write Timing Check Latency Register" hexmask.long 0x0 0.--31. 1. "SAWL,Sum of the AXI Write Latencies" repeat 64. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2+0x300)++0x0 line.byte 0x0 "MPPKR[$1],Manufacturing Protection Private Key Register" hexmask.byte 0x0 0.--7. 1. "MPPrivK,MPPrivK. The 512-bit Manufacturing Protection Private Key." repeat.end repeat 32. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2+0x380)++0x0 line.byte 0x0 "MPMR[$1],Manufacturing Protection Message Register" hexmask.byte 0x0 0.--7. 1. "MPMSG,Holds 256 bits of message data that will be prepended to the input data to the MPSIGN operation" repeat.end repeat 32. (increment 0x0 0x1)(increment 0x0 0x1) rgroup.byte ($2+0x3C0)++0x0 line.byte 0x0 "MPTESTR[$1],Manufacturing Protection Test Register" hexmask.byte 0x0 0.--7. 1. "TEST_VALUE,TEST_VALUE" repeat.end rgroup.long 0x3F8++0x3 line.long 0x0 "MPECC,Manufacturing Protection ECC Register" bitfld.long 0x0 27. "MP_ZERO,This bit indicates if the Manufacturing Protection Key that is programmed in the Security Fuse Processor has an all-zero value" "0: The MP Key in the SFP has a non-zero value.,1: The MP Key in the SFP is all zeros (unprogrammed)." newline hexmask.long.word 0x0 16.--24. 1. "MP_SYNDROME,This is the syndrome produced by the ECC check on the Manufacturing Protection Key that is programmed in the Security Fuse Processor" repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x400)++0x3 line.long 0x0 "JDKEKR[$1],Job Descriptor Key Encryption Key Register" hexmask.long 0x0 0.--31. 1. "JDKEK,The 256-bit Job Descriptor Key Encryption Key used to encrypt and decrypt Black Keys." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x420)++0x3 line.long 0x0 "TDKEKR[$1],Trusted Descriptor Key Encryption Key Register" hexmask.long 0x0 0.--31. 1. "TDKEK,The 256-bit Trusted Descriptor Key Encryption Key used to encrypt and decrypt Black Keys." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x440)++0x3 line.long 0x0 "TDSKR[$1],Trusted Descriptor Signing Key Register" hexmask.long 0x0 0.--31. 1. "TDSK,The 256-bit Trusted Descriptor Signing Key used to sign and verify Trusted Descriptors." repeat.end group.quad 0x4E0++0x7 line.quad 0x0 "SKNR,Secure Key Nonce Register" hexmask.quad.word 0x0 32.--46. 1. "SK_NONCE_MS,Secure Key Nonce - Most Significant Bits" newline hexmask.quad.long 0x0 0.--31. 1. "SK_NONCE_LS,Secure Key Nonce - Least Significant Bits" rgroup.long 0x50C++0x13 line.long 0x0 "DMA_STA,DMA Status Register" bitfld.long 0x0 7. "DMA0_IDLE,DMA0 is idle. DMA0's command queue is empty." "0,1" newline bitfld.long 0x0 5. "DMA0_ITIF,DMA0 Internal Transactions in Flight" "0,1" newline hexmask.long.byte 0x0 0.--4. 1. "DMA0_ETIF,DMA0 External Transactions in Flight" line.long 0x4 "DMA_X_AID_7_4_MAP,DMA_X_AID_7_4_MAP" hexmask.long.byte 0x4 24.--31. 1. "AID7_BID,This field shows the CAAM Block ID that uses AXI ID 7." newline hexmask.long.byte 0x4 16.--23. 1. "AID6_BID,This field shows the CAAM Block ID that uses AXI ID 6." newline hexmask.long.byte 0x4 8.--15. 1. "AID5_BID,This field shows the CAAM Block ID that uses AXI ID 5." newline hexmask.long.byte 0x4 0.--7. 1. "AID4_BID,This field shows the CAAM Block ID that uses AXI ID 4." line.long 0x8 "DMA_X_AID_3_0_MAP,DMA_X_AID_3_0_MAP" hexmask.long.byte 0x8 24.--31. 1. "AID3_BID,This field shows the CAAM Block ID that uses AXI ID 3." newline hexmask.long.byte 0x8 16.--23. 1. "AID2_BID,This field shows the CAAM Block ID that uses AXI ID 2." newline hexmask.long.byte 0x8 8.--15. 1. "AID1_BID,This field shows the CAAM Block ID that uses AXI ID 1." newline hexmask.long.byte 0x8 0.--7. 1. "AID0_BID,This field shows the CAAM Block ID that uses AXI ID 0." line.long 0xC "DMA_X_AID_15_12_MAP,DMA_X_AID_15_12_MAP" hexmask.long.byte 0xC 24.--31. 1. "AID15_BID,This field shows the CAAM Block ID that uses AXI ID 15." newline hexmask.long.byte 0xC 16.--23. 1. "AID14_BID,This field shows the CAAM Block ID that uses AXI ID 14." newline hexmask.long.byte 0xC 8.--15. 1. "AID13_BID,This field shows the CAAM Block ID that uses AXI ID 13." newline hexmask.long.byte 0xC 0.--7. 1. "AID12_BID,This field shows the CAAM Block ID that uses AXI ID 12." line.long 0x10 "DMA_X_AID_11_8_MAP,DMA_X_AID_11_8_MAP" hexmask.long.byte 0x10 24.--31. 1. "AID11_BID,This field shows the CAAM Block ID that uses AXI ID 11." newline hexmask.long.byte 0x10 16.--23. 1. "AID10_BID,This field shows the CAAM Block ID that uses AXI ID 10." newline hexmask.long.byte 0x10 8.--15. 1. "AID9_BID,This field shows the CAAM Block ID that uses AXI ID 9." newline hexmask.long.byte 0x10 0.--7. 1. "AID8_BID,This field shows the CAAM Block ID that uses AXI ID 8." rgroup.long 0x524++0x3 line.long 0x0 "DMA_X_AID_15_0_EN,DMA_X AXI ID Map Enable Register" bitfld.long 0x0 15. "AID15E,If AID15E=1 then AXI ID 15 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 14. "AID14E,If AID14E=1 then AXI ID 14 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 13. "AID13E,If AID13E=1 then AXI ID 13 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 12. "AID12E,If AID12E=1 then AXI ID 12 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 11. "AID11E,If AID11E=1 then AXI ID 11 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 10. "AID10E,If AID10E=1 then AXI ID 10 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 9. "AID9E,If AID9E=1 then AXI ID 9 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 8. "AID8E,If AID8E=1 then AXI ID 8 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 7. "AID7E,If AID7E=1 then AXI ID 7 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 6. "AID6E,If AID6E=1 then AXI ID 6 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 5. "AID5E,If AID5E=1 then AXI ID 5 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 4. "AID4E,If AID4E=1 then AXI ID 4 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 3. "AID3E,If AID3E=1 then AXI ID 3 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 2. "AID2E,If AID2E=1 then AXI ID 2 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 1. "AID1E,If AID1E=1 then AXI ID 1 is enabled for this DMA engine." "0,1" newline bitfld.long 0x0 0. "AID0E,If AID0E=1 then AXI ID 0 is enabled for this DMA engine." "0,1" group.long 0x530++0x1F line.long 0x0 "DMA_X_ARTC_CTL,DMA_X AXI Read Timing Check Control Register" bitfld.long 0x0 31. "ARTCE,AXI Read Timing Check Enable" "0,1" newline bitfld.long 0x0 30. "ARCT,AXI Read Counter Test" "0,1" newline bitfld.long 0x0 29. "ARTT,AXI Read Timer Test" "0,1" newline bitfld.long 0x0 28. "ARTL,AXI Read Timer Last" "0,1" newline hexmask.long.word 0x0 16.--27. 1. "ARL,AXI Read Limit" newline hexmask.long.word 0x0 0.--11. 1. "ART,AXI Read Timer" line.long 0x4 "DMA_X_ARTC_LC,DMA_X AXI Read Timing Check Late Count Register" hexmask.long.tbyte 0x4 0.--19. 1. "ARLC,AXI Read Late Count" line.long 0x8 "DMA_X_ARTC_SC,DMA_X AXI Read Timing Check Sample Count Register" hexmask.long.tbyte 0x8 0.--19. 1. "ARSC,AXI Read Sample Count" line.long 0xC "DMA_X_ARTC_LAT,DMA_X Read Timing Check Latency Register" hexmask.long 0xC 0.--31. 1. "SARL,Sum of the AXI Read Latencies" line.long 0x10 "DMA_X_AWTC_CTL,DMA_X AXI Write Timing Check Control Register" bitfld.long 0x10 31. "AWTCE,AXI Write Timing Check Enable" "0,1" newline bitfld.long 0x10 30. "AWCT,AXI Write Counter Test" "0,1" newline bitfld.long 0x10 29. "AWTT,AXI Write Timer Test" "0,1" newline hexmask.long.word 0x10 16.--27. 1. "AWL,AXI Write Limit" newline hexmask.long.word 0x10 0.--11. 1. "AWT,AXI Write Timer" line.long 0x14 "DMA_X_AWTC_LC,DMA_X AXI Write Timing Check Late Count Register" hexmask.long.tbyte 0x14 0.--19. 1. "AWLC,AXI Write Late Count" line.long 0x18 "DMA_X_AWTC_SC,DMA_X AXI Write Timing Check Sample Count Register" hexmask.long.tbyte 0x18 0.--19. 1. "AWSC,AXI Write Sample Count" line.long 0x1C "DMA_X_AWTC_LAT,DMA_X Write Timing Check Latency Register" hexmask.long 0x1C 0.--31. 1. "SAWL,Sum of the AXI Write Latencies" group.long 0x600++0xF line.long 0x0 "RTMCTL,RNG TRNG Miscellaneous Control Register" bitfld.long 0x0 16. "PRGM,Programming Mode Select" "0,1" newline rbitfld.long 0x0 13. "TSTOP_OK,TRNG_OK_TO_STOP" "0,1" newline eventfld.long 0x0 12. "ERR,Read: Error status" "0,1" newline rbitfld.long 0x0 11. "TST_OUT,Read only: Test point inside ring oscillator." "0,1" newline rbitfld.long 0x0 10. "ENT_VAL,Read only: Entropy Valid" "0,1" newline rbitfld.long 0x0 9. "FCT_VAL,Read only: Frequency Count Valid. Indicates that a valid frequency count may be read from RTFRQCNT." "0,1" newline rbitfld.long 0x0 8. "FCT_FAIL,Read only: Frequency Count Fail" "0,1" newline bitfld.long 0x0 7. "FORCE_SYSCLK,Force System Clock" "0,1" newline bitfld.long 0x0 6. "RST_DEF,Reset Defaults" "0,1" newline bitfld.long 0x0 5. "TRNG_ACC,TRNG Access Mode" "0,1" newline bitfld.long 0x0 4. "CLK_OUT_EN,Clock Output Enable" "0,1" newline bitfld.long 0x0 2.--3. "OSC_DIV,Oscillator Divide" "0: use ring oscillator with no divide,1: use ring oscillator divided-by-2,2: use ring oscillator divided-by-4,3: use ring oscillator divided-by-8" newline bitfld.long 0x0 0.--1. "SAMP_MODE,Sample Mode" "0: use Von Neumann data into both Entropy shifter..,1: use raw data into both Entropy shifter and..,2: use Von Neumann data into Entropy shifter. Use..,?" line.long 0x4 "RTSCMISC,RNG TRNG Statistical Check Miscellaneous Register" hexmask.long.byte 0x4 16.--19. 1. "RTY_CNT,RETRY COUNT" newline hexmask.long.byte 0x4 0.--7. 1. "LRUN_MAX,LONG RUN MAX LIMIT" line.long 0x8 "RTPKRRNG,RNG TRNG Poker Range Register" hexmask.long.word 0x8 0.--15. 1. "PKR_RNG,Poker Range" line.long 0xC "RTPKRMAX,RNG TRNG Poker Maximum Limit Register" hexmask.long.tbyte 0xC 0.--23. 1. "PKR_MAX,Poker Maximum Limit" rgroup.long 0x60C++0x3 line.long 0x0 "RTPKRSQ,RNG TRNG Poker Square Calculation Result Register" hexmask.long.tbyte 0x0 0.--23. 1. "PKR_SQ,Poker Square Calculation Result" group.long 0x610++0x7 line.long 0x0 "RTSDCTL,RNG TRNG Seed Control Register" hexmask.long.word 0x0 16.--31. 1. "ENT_DLY,Entropy Delay" newline hexmask.long.word 0x0 0.--15. 1. "SAMP_SIZE,Sample Size" line.long 0x4 "RTSBLIM,RNG TRNG Sparse Bit Limit Register" hexmask.long.word 0x4 0.--9. 1. "SB_LIM,Sparse Bit Limit" rgroup.long 0x614++0x3 line.long 0x0 "RTTOTSAM,RNG TRNG Total Samples Register" hexmask.long.tbyte 0x0 0.--19. 1. "TOT_SAM,Total Samples" group.long 0x618++0x3 line.long 0x0 "RTFRQMIN,RNG TRNG Frequency Count Minimum Limit Register" hexmask.long.tbyte 0x0 0.--21. 1. "FRQ_MIN,Frequency Count Minimum Limit" rgroup.long 0x61C++0x3 line.long 0x0 "RTFRQCNT,RNG TRNG Frequency Count Register" hexmask.long.tbyte 0x0 0.--21. 1. "FRQ_CNT,Frequency Count" group.long 0x61C++0x3 line.long 0x0 "RTFRQMAX,RNG TRNG Frequency Count Maximum Limit Register" hexmask.long.tbyte 0x0 0.--21. 1. "FRQ_MAX,Frequency Counter Maximum Limit" rgroup.long 0x620++0x3 line.long 0x0 "RTSCMC,RNG TRNG Statistical Check Monobit Count Register" hexmask.long.word 0x0 0.--15. 1. "MONO_CNT,Monobit Count" group.long 0x620++0x3 line.long 0x0 "RTSCML,RNG TRNG Statistical Check Monobit Limit Register" hexmask.long.word 0x0 16.--31. 1. "MONO_RNG,Monobit Range" newline hexmask.long.word 0x0 0.--15. 1. "MONO_MAX,Monobit Maximum Limit" rgroup.long 0x624++0x3 line.long 0x0 "RTSCR1C,RNG TRNG Statistical Check Run Length 1 Count Register" hexmask.long.word 0x0 16.--30. 1. "R1_1_COUNT,Runs of One Length 1 Count" newline hexmask.long.word 0x0 0.--14. 1. "R1_0_COUNT,Runs of Zero Length 1 Count" group.long 0x624++0x3 line.long 0x0 "RTSCR1L,RNG TRNG Statistical Check Run Length 1 Limit Register" hexmask.long.word 0x0 16.--30. 1. "RUN1_RNG,Run Length 1 Range" newline hexmask.long.word 0x0 0.--14. 1. "RUN1_MAX,Run Length 1 Maximum Limit" rgroup.long 0x628++0x3 line.long 0x0 "RTSCR2C,RNG TRNG Statistical Check Run Length 2 Count Register" hexmask.long.word 0x0 16.--29. 1. "R2_1_COUNT,Runs of One Length 2 Count" newline hexmask.long.word 0x0 0.--13. 1. "R2_0_COUNT,Runs of Zero Length 2 Count" group.long 0x628++0x3 line.long 0x0 "RTSCR2L,RNG TRNG Statistical Check Run Length 2 Limit Register" hexmask.long.word 0x0 16.--29. 1. "RUN2_RNG,Run Length 2 Range" newline hexmask.long.word 0x0 0.--13. 1. "RUN2_MAX,Run Length 2 Maximum Limit" rgroup.long 0x62C++0x3 line.long 0x0 "RTSCR3C,RNG TRNG Statistical Check Run Length 3 Count Register" hexmask.long.word 0x0 16.--28. 1. "R3_1_COUNT,Runs of Ones Length 3 Count" newline hexmask.long.word 0x0 0.--12. 1. "R3_0_COUNT,Runs of Zeroes Length 3 Count" group.long 0x62C++0x3 line.long 0x0 "RTSCR3L,RNG TRNG Statistical Check Run Length 3 Limit Register" hexmask.long.word 0x0 16.--28. 1. "RUN3_RNG,Run Length 3 Range" newline hexmask.long.word 0x0 0.--12. 1. "RUN3_MAX,Run Length 3 Maximum Limit" rgroup.long 0x630++0x3 line.long 0x0 "RTSCR4C,RNG TRNG Statistical Check Run Length 4 Count Register" hexmask.long.word 0x0 16.--27. 1. "R4_1_COUNT,Runs of One Length 4 Count" newline hexmask.long.word 0x0 0.--11. 1. "R4_0_COUNT,Runs of Zero Length 4 Count" group.long 0x630++0x3 line.long 0x0 "RTSCR4L,RNG TRNG Statistical Check Run Length 4 Limit Register" hexmask.long.word 0x0 16.--27. 1. "RUN4_RNG,Run Length 4 Range" newline hexmask.long.word 0x0 0.--11. 1. "RUN4_MAX,Run Length 4 Maximum Limit" rgroup.long 0x634++0x3 line.long 0x0 "RTSCR5C,RNG TRNG Statistical Check Run Length 5 Count Register" hexmask.long.word 0x0 16.--26. 1. "R5_1_COUNT,Runs of One Length 5 Count" newline hexmask.long.word 0x0 0.--10. 1. "R5_0_COUNT,Runs of Zero Length 5 Count" group.long 0x634++0x3 line.long 0x0 "RTSCR5L,RNG TRNG Statistical Check Run Length 5 Limit Register" hexmask.long.word 0x0 16.--26. 1. "RUN5_RNG,Run Length 5 Range" newline hexmask.long.word 0x0 0.--10. 1. "RUN5_MAX,Run Length 5 Maximum Limit" rgroup.long 0x638++0x3 line.long 0x0 "RTSCR6PC,RNG TRNG Statistical Check Run Length 6+ Count Register" hexmask.long.word 0x0 16.--26. 1. "R6P_1_COUNT,Runs of One Length 6+ Count" newline hexmask.long.word 0x0 0.--10. 1. "R6P_0_COUNT,Runs of Zero Length 6+ Count" group.long 0x638++0x3 line.long 0x0 "RTSCR6PL,RNG TRNG Statistical Check Run Length 6+ Limit Register" hexmask.long.word 0x0 16.--26. 1. "RUN6P_RNG,Run Length 6+ Range" newline hexmask.long.word 0x0 0.--10. 1. "RUN6P_MAX,Run Length 6+ Maximum Limit" rgroup.long 0x63C++0x3 line.long 0x0 "RTSTATUS,RNG TRNG Status Register" hexmask.long.byte 0x0 16.--19. 1. "RETRY_COUNT,RETRY COUNT" newline bitfld.long 0x0 15. "FMBTF,Mono Bit Test Fail. If MBTF=1 the Mono Bit Test has failed." "0,1" newline bitfld.long 0x0 14. "FPTF,Poker Test Fail. If PTF=1 the Poker Test has failed." "0,1" newline bitfld.long 0x0 13. "FLRTF,Long Run Test Fail. If LRTF=1 the Long Run Test has failed." "0,1" newline bitfld.long 0x0 12. "FSBTF,Sparse Bit Test Fail. If SBTF=1 the Sparse Bit Test has failed." "0,1" newline bitfld.long 0x0 11. "F6PBR1TF,6 Plus Bit Run Sampling 1s Test Fail" "0,1" newline bitfld.long 0x0 10. "F6PBR0TF,6 Plus Bit Run Sampling 0s Test Fail" "0,1" newline bitfld.long 0x0 9. "F5BR1TF,5-Bit Run Sampling 1s Test Fail. If 5BR1TF=1 the 5-Bit Run Sampling 1s Test has failed." "0,1" newline bitfld.long 0x0 8. "F5BR0TF,5-Bit Run Sampling 0s Test Fail. If 5BR0TF=1 the 5-Bit Run Sampling 0s Test has failed." "0,1" newline bitfld.long 0x0 7. "F4BR1TF,4-Bit Run Sampling 1s Test Fail. If 4BR1TF=1 the 4-Bit Run Sampling 1s Test has failed." "0,1" newline bitfld.long 0x0 6. "F4BR0TF,4-Bit Run Sampling 0s Test Fail. If 4BR0TF=1 the 4-Bit Run Sampling 0s Test has failed." "0,1" newline bitfld.long 0x0 5. "F3BR1TF,3-Bit Run Sampling 1s Test Fail. If 3BR1TF=1 the 3-Bit Run Sampling 1s Test has failed." "0,1" newline bitfld.long 0x0 4. "F3BR01TF,3-Bit Run Sampling 0s Test Fail. If 3BR0TF=1 the 3-Bit Run Sampling 0s Test has failed." "0,1" newline bitfld.long 0x0 3. "F2BR1TF,2-Bit Run Sampling 1s Test Fail. If 2BR1TF=1 the 2-Bit Run Sampling 1s Test has failed." "0,1" newline bitfld.long 0x0 2. "F2BR0TF,2-Bit Run Sampling 0s Test Fail. If 2BR0TF=1 the 2-Bit Run Sampling 0s Test has failed." "0,1" newline bitfld.long 0x0 1. "F1BR1TF,1-Bit Run Sampling 1s Test Fail. If 1BR1TF=1 the 1-Bit Run Sampling 1s Test has failed." "?,1: Bit Run" newline bitfld.long 0x0 0. "F1BR0TF,1-Bit Run Sampling 0s Test Fail. If 1BR0TF=1 the 1-Bit Run Sampling 0s Test has failed." "?,1: Bit Run" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x640)++0x3 line.long 0x0 "RTENT[$1],RNG TRNG Entropy Read Register" hexmask.long 0x0 0.--31. 1. "ENT,Entropy Value" repeat.end rgroup.long 0x680++0x1F line.long 0x0 "RTPKRCNT10,RNG TRNG Statistical Check Poker Count 1 and 0 Register" hexmask.long.word 0x0 16.--31. 1. "PKR_1_CNT,Poker 1h Count" newline hexmask.long.word 0x0 0.--15. 1. "PKR_0_CNT,Poker 0h Count" line.long 0x4 "RTPKRCNT32,RNG TRNG Statistical Check Poker Count 3 and 2 Register" hexmask.long.word 0x4 16.--31. 1. "PKR_3_CNT,Poker 3h Count" newline hexmask.long.word 0x4 0.--15. 1. "PKR_2_CNT,Poker 2h Count" line.long 0x8 "RTPKRCNT54,RNG TRNG Statistical Check Poker Count 5 and 4 Register" hexmask.long.word 0x8 16.--31. 1. "PKR_5_CNT,Poker 5h Count" newline hexmask.long.word 0x8 0.--15. 1. "PKR_4_CNT,Poker 4h Count" line.long 0xC "RTPKRCNT76,RNG TRNG Statistical Check Poker Count 7 and 6 Register" hexmask.long.word 0xC 16.--31. 1. "PKR_7_CNT,Poker 7h Count" newline hexmask.long.word 0xC 0.--15. 1. "PKR_6_CNT,Poker 6h Count" line.long 0x10 "RTPKRCNT98,RNG TRNG Statistical Check Poker Count 9 and 8 Register" hexmask.long.word 0x10 16.--31. 1. "PKR_9_CNT,Poker 9h Count" newline hexmask.long.word 0x10 0.--15. 1. "PKR_8_CNT,Poker 8h Count" line.long 0x14 "RTPKRCNTBA,RNG TRNG Statistical Check Poker Count B and A Register" hexmask.long.word 0x14 16.--31. 1. "PKR_B_CNT,Poker Bh Count" newline hexmask.long.word 0x14 0.--15. 1. "PKR_A_CNT,Poker Ah Count" line.long 0x18 "RTPKRCNTDC,RNG TRNG Statistical Check Poker Count D and C Register" hexmask.long.word 0x18 16.--31. 1. "PKR_D_CNT,Poker Dh Count" newline hexmask.long.word 0x18 0.--15. 1. "PKR_C_CNT,Poker Ch Count" line.long 0x1C "RTPKRCNTFE,RNG TRNG Statistical Check Poker Count F and E Register" hexmask.long.word 0x1C 16.--31. 1. "PKR_F_CNT,Poker Fh Count" newline hexmask.long.word 0x1C 0.--15. 1. "PKR_E_CNT,Poker Eh Count" rgroup.long 0x6C0++0x3 line.long 0x0 "RDSTA,RNG DRNG Status Register" bitfld.long 0x0 31. "SKVT,Secure Key Valid Test" "0,1" newline bitfld.long 0x0 30. "SKVN,Secure Key Valid Non-Test" "0,1" newline bitfld.long 0x0 20. "CE,Catastrophic Error" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "ERRCODE,Error Code. These bits represent the current error in the RNG." newline bitfld.long 0x0 9. "TF1,Test Flag State Handle 1. State handle 1 has been instantiated as a test (deterministic) instance." "0,1" newline bitfld.long 0x0 8. "TF0,Test Flag State Handle 0. State handle 0 has been instantiated as a test (deterministic) instance." "0,1" newline bitfld.long 0x0 5. "PR1,Prediction Resistance Flag State Handle 1" "0,1" newline bitfld.long 0x0 4. "PR0,Prediction Resistance Flag State Handle 0" "0,1" newline bitfld.long 0x0 1. "IF1,Instantiated Flag State Handle 1. State Handle 1 has been instantiated." "0,1" newline bitfld.long 0x0 0. "IF0,Instantiated Flag State Handle 0. State Handle 0 has been instantiated." "0,1" rgroup.long 0x6D0++0x7 line.long 0x0 "RDINT0,RNG DRNG State Handle 0 Reseed Interval Register" hexmask.long 0x0 0.--31. 1. "RESINT0,RESINT0. This read-only register holds the Reseed Interval for State Handle 0." line.long 0x4 "RDINT1,RNG DRNG State Handle 1 Reseed Interval Register" hexmask.long 0x4 0.--31. 1. "RESINT1,RESINT1. This read-only register holds the Reseed Interval for State Handle 1." group.long 0x6E0++0x3 line.long 0x0 "RDHCNTL,RNG DRNG Hash Control Register" bitfld.long 0x0 4. "HTC,Hashing Test Mode Clear. Writing this bit will take the RNG out of hashing test mode." "0,1" newline bitfld.long 0x0 3. "HTM,Hashing Test Mode. Writing this bit will put RNG in Hashing Test Mode." "0,1" newline bitfld.long 0x0 2. "HI,Hashing Initialize. Writing to this bit will initialize the Hashing Engine." "0,1" newline bitfld.long 0x0 1. "HB,Hashing Begin. Writing this bit will causing the Hashing Engine to begin hashing." "0,1" newline rbitfld.long 0x0 0. "HD,Hashing Done. This bit asserts when the hashing engine is done." "0,1" rgroup.long 0x6E4++0x3 line.long 0x0 "RDHDIG,RNG DRNG Hash Digest Register" hexmask.long 0x0 0.--31. 1. "HASHMD,HASHMD" wgroup.long 0x6E8++0x3 line.long 0x0 "RDHBUF,RNG DRNG Hash Buffer Register" hexmask.long 0x0 0.--31. 1. "HASHBUF,HASHBUF" rgroup.long 0xA00++0x3 line.long 0x0 "P0SDID_PG0,Partition 0 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA04++0xB line.long 0x0 "P0SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P0SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P0SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA10++0x3 line.long 0x0 "P1SDID_PG0,Partition 1 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA14++0xB line.long 0x0 "P1SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P1SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P1SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA20++0x3 line.long 0x0 "P2SDID_PG0,Partition 2 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA24++0xB line.long 0x0 "P2SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P2SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P2SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA30++0x3 line.long 0x0 "P3SDID_PG0,Partition 3 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA34++0xB line.long 0x0 "P3SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P3SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P3SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA40++0x3 line.long 0x0 "P4SDID_PG0,Partition 4 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA44++0xB line.long 0x0 "P4SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P4SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P4SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA50++0x3 line.long 0x0 "P5SDID_PG0,Partition 5 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA54++0xB line.long 0x0 "P5SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P5SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P5SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA60++0x3 line.long 0x0 "P6SDID_PG0,Partition 6 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA64++0xB line.long 0x0 "P6SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P6SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P6SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA70++0x3 line.long 0x0 "P7SDID_PG0,Partition 7 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA74++0xB line.long 0x0 "P7SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P7SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P7SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA80++0x3 line.long 0x0 "P8SDID_PG0,Partition 8 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA84++0xB line.long 0x0 "P8SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P8SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P8SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xA90++0x3 line.long 0x0 "P9SDID_PG0,Partition 9 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xA94++0xB line.long 0x0 "P9SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P9SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P9SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAA0++0x3 line.long 0x0 "P10SDID_PG0,Partition 10 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAA4++0xB line.long 0x0 "P10SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P10SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P10SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAB0++0x3 line.long 0x0 "P11SDID_PG0,Partition 11 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAB4++0xB line.long 0x0 "P11SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P11SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P11SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAC0++0x3 line.long 0x0 "P12SDID_PG0,Partition 12 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAC4++0xB line.long 0x0 "P12SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P12SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P12SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAD0++0x3 line.long 0x0 "P13SDID_PG0,Partition 13 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAD4++0xB line.long 0x0 "P13SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P13SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P13SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAE0++0x3 line.long 0x0 "P14SDID_PG0,Partition 14 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAE4++0xB line.long 0x0 "P14SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P14SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P14SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0xAF0++0x3 line.long 0x0 "P15SDID_PG0,Partition 15 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0xAF4++0x13 line.long 0x0 "P15SMAPR_PG0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P15SMAG2_PG0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P15SMAG1_PG0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0xC "REIS,Recoverable Error Interrupt Status" eventfld.long 0xC 27. "JBAE3,A job descriptor executed from Job Ring 3 caused a bus access error." "0,1" newline eventfld.long 0xC 26. "JBAE2,A job descriptor executed from Job Ring 2 caused a bus access error." "0,1" newline eventfld.long 0xC 25. "JBAE1,A job descriptor executed from Job Ring 1 caused a bus access error." "0,1" newline eventfld.long 0xC 24. "JBAE0,A job descriptor executed from Job Ring 0 caused a bus access error." "0,1" newline eventfld.long 0xC 16. "RBAE,A bus transaction initiated by CAAM RTIC resulted in a bus access error." "0,1" newline eventfld.long 0xC 0. "CWDE,The CAAM watchdog timer expired." "0,1" line.long 0x10 "REIE,Recoverable Error Interrupt Enable" bitfld.long 0x10 27. "JBAE3,JR3-initiated job execution caused bus access error" "0,1" newline bitfld.long 0x10 26. "JBAE2,JR2-initiated job execution caused bus access error" "0,1" newline bitfld.long 0x10 25. "JBAE1,JR1-initiated job execution caused bus access error" "?,1: initiated job execution caused bus access error" newline bitfld.long 0x10 24. "JBAE0,JR0-initiated job execution caused bus access error" "0: initiated job execution caused bus access error,?" newline bitfld.long 0x10 16. "RBAE,RTIC-initiated job execution caused bus access error." "0,1" newline bitfld.long 0x10 0. "CWDE,CAAM watchdog timer expired" "0,1" rgroup.long 0xB08++0x3 line.long 0x0 "REIF,Recoverable Error Interrupt Force" bitfld.long 0x0 27. "JBAE3,JR3-initiated job execution caused bus access error" "0,1" newline bitfld.long 0x0 26. "JBAE2,JR2-initiated job execution caused bus access error" "0,1" newline bitfld.long 0x0 25. "JBAE1,JR1-initiated job execution caused bus access error" "?,1: initiated job execution caused bus access error" newline bitfld.long 0x0 24. "JBAE0,JR0-initiated job execution caused bus access error" "0: initiated job execution caused bus access error,?" newline bitfld.long 0x0 16. "RBAE,RTIC-initiated job execution caused bus access error." "0,1" newline bitfld.long 0x0 0. "CWDE,CAAM watchdog timer expired" "0,1" group.long 0xB0C++0x3 line.long 0x0 "REIH,Recoverable Error Interrupt Halt" bitfld.long 0x0 27. "JBAE3,Halt CAAM if JR3-initiated job execution caused bus access error." "0: Don't halt CAAM if JR3-initiated job execution..,1: Halt CAAM if JR3-initiated job execution caused.." newline bitfld.long 0x0 26. "JBAE2,Halt CAAM if JR2-initiated job execution caused bus access error." "0: Don't halt CAAM if JR2-initiated job execution..,1: Halt CAAM if JR2-initiated job execution caused.." newline bitfld.long 0x0 25. "JBAE1,Halt CAAM if JR1-initiated job execution caused bus access error." "0: Don't halt CAAM if JR1-initiated job execution..,1: initiated job execution caused bus access error" newline bitfld.long 0x0 24. "JBAE0,Halt CAAM if JR0-initiated job execution caused bus access error." "0: initiated job execution caused bus access error,1: Halt CAAM if JR0-initiated job execution caused.." newline bitfld.long 0x0 16. "RBAE,Halt CAAM if RTIC-initiated job execution caused bus access error." "0: Don't halt CAAM if RTIC-initiated job execution..,1: Halt CAAM if RTIC-initiated job execution caused.." newline bitfld.long 0x0 0. "CWDE,Halt CAAM if CAAM watchdog timer expires." "0: Don't halt CAAM if CAAM watchdog expired.,1: Halt CAAM if CAAM watchdog expired.." repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xBD0)++0x3 line.long 0x0 "SMWPJRR[$1],Secure Memory Write Protect Job Ring Register" bitfld.long 0x0 0. "SMR_WP_JRa,Secure Memory Registers Write Protect" "0,1" repeat.end wgroup.long 0xBE4++0x3 line.long 0x0 "SMCR_PG0,Secure Memory Command Register" hexmask.long.word 0x0 16.--31. 1. "PAGE,This is the number of the page to be referenced in field CMD" newline hexmask.long.byte 0x0 8.--11. 1. "PRTN,Partition: When an Allocate Page or De-allocate Partition command is issued the action is performed on the partition indicated in the PRTN field" newline hexmask.long.byte 0x0 0.--3. 1. "CMD,Command: 1h: Allocate Page - This command allocates the page specified in the PAGE field to the partition specified in the PRTN field" rgroup.long 0xBEC++0x3 line.long 0x0 "SMCSR_PG0,Secure Memory Command Status Register" hexmask.long.word 0x0 16.--27. 1. "PAGE,Page" newline bitfld.long 0x0 14.--15. "CERR,Command Error" "0: No Error.,1: Command has not yet completed.,2: A security failure occurred.,3: Command Overflow. Another command was issued by.." newline bitfld.long 0x0 12.--13. "AERR,Allocation Error" "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO,Page Owner: Following a Page Inquiry Command this field indicates if the Page is owned by the entity that issued the inquiry owned by another entity or unowned" "0: Available; Unowned: The entity that issued the..,1: Page does not exist in this version or is not..,2: Another entity owns the page. This page is..,3: Owned by the entity making the inquiry. The.." newline hexmask.long.byte 0x0 0.--3. 1. "PRTN,Following a Page Inquiry Command if the PO field is 10 or 11 this field indicates the partition to which the page specified in the PAGE field is allocated" rgroup.quad 0xC00++0xF line.quad 0x0 "HT0_JD_ADDR,Holding Tank 0 Job Descriptor Address" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x8 "HT0_SD_ADDR,Holding Tank 0 Shared Descriptor Address" hexmask.quad 0x8 0.--35. 1. "SD_ADDR,Shared Descriptor Address." rgroup.long 0xC10++0x7 line.long 0x0 "HT0_JQ_CTRL_MS,Holding Tank 0 Job Queue Control. most-significant half" bitfld.long 0x0 29. "WHL,Whole Descriptor" "0,1" newline bitfld.long 0x0 28. "FOUR,Four Words. Job Queue Controller will pass at least 4 words of the descriptor to DECO." "0,1" newline bitfld.long 0x0 27. "ILE,Immediate Little Endian" "0: No byte-swapping is performed for immediate data..,1: Byte-swapping is performed for immediate data.." newline hexmask.long.byte 0x0 22.--26. 1. "SHR_FROM,Share From" newline bitfld.long 0x0 19. "DWORD_SWAP,Double Word Swap." "0: DWords are in the order most-significant word..,1: DWords are in the order least-significant word.." newline bitfld.long 0x0 17.--18. "HT_ERROR,Holding Tank Error. (This field is implemented only in versions of CAAM that support prefetching.)" "0: No error,1: Job Descriptor or Shared Descriptor length error,2: AXI_error while reading a Job Ring Shared..,?" newline bitfld.long 0x0 16. "SOB,Shared or Burst" "0,1" newline bitfld.long 0x0 15. "AMTD,Allow Make Trusted Descriptor" "0,1" newline bitfld.long 0x0 14. "JDDS,Job Descriptor DID Select" "0: Non-SEQ DID,1: SEQ DID" newline bitfld.long 0x0 8.--10. "SRC,Job Source" "0: Job Ring 0,1: Job Ring 1,2: Job Ring 2,3: Job Ring 3,4: RTIC,?,?,?" newline bitfld.long 0x0 0.--2. "ID,Job ID" "0,1,2,3,4,5,6,7" line.long 0x4 "HT0_JQ_CTRL_LS,Holding Tank 0 Job Queue Control. least-significant half" hexmask.long.word 0x4 21.--31. 1. "OUT_ICID,Output ICID" newline hexmask.long.byte 0x4 16.--19. 1. "OUT_DID,Output DID" newline hexmask.long.word 0x4 5.--15. 1. "PRIM_ICID,Primary ICID" newline bitfld.long 0x4 4. "PRIM_TZ,Primary TZ" "0: TrustZone NonSecureWorld,1: TrustZone SecureWorld" newline hexmask.long.byte 0x4 0.--3. 1. "PRIM_DID,Primary DID" rgroup.long 0xC1C++0x3 line.long 0x0 "HT0_STATUS,Holding Tank Status" bitfld.long 0x0 31. "BC,Been Changed" "0,1" newline bitfld.long 0x0 30. "IN_USE,In Use" "0,1" newline bitfld.long 0x0 0. "PEND_0,Pending for DECO 0" "0,1" group.long 0xC24++0x3 line.long 0x0 "JQ_DEBUG_SEL,Job Queue Debug Select Register" rbitfld.long 0x0 16.--18. "JOB_ID,Job ID" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0. "HT_SEL,Holding Tank Select" "0,1" rgroup.long 0xDBC++0xB line.long 0x0 "JRJIDU_LS,Job Ring Job IDs in Use Register. least-significant half" bitfld.long 0x0 3. "JID03,Job ID 03" "0,1" newline bitfld.long 0x0 2. "JID02,Job ID 02" "0,1" newline bitfld.long 0x0 1. "JID01,Job ID 01" "0,1" newline bitfld.long 0x0 0. "JID00,Job ID 00" "0,1" line.long 0x4 "JRJDJIFBC,Job Ring Job-Done Job ID FIFO BC" bitfld.long 0x4 31. "BC,Been changed" "0,1" line.long 0x8 "JRJDJIF,Job Ring Job-Done Job ID FIFO" bitfld.long 0x8 0.--2. "JOB_ID_ENTRY,Job ID entry" "0,1,2,3,4,5,6,7" rgroup.long 0xDE4++0x3 line.long 0x0 "JRJDS1,Job Ring Job-Done Source 1" bitfld.long 0x0 31. "VALID,Valid" "0,1" newline bitfld.long 0x0 0.--1. "SRC,Source" "0,1,2,3" rgroup.quad 0xE00++0x7 line.quad 0x0 "JRJDDA,Job Ring Job-Done Descriptor Address 0 Register" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." rgroup.long 0xFA0++0xF line.long 0x0 "CRNR_MS,CHA Revision Number Register. most-significant half" hexmask.long.byte 0x0 28.--31. 1. "JRRN,Job Ring Revision Number" newline hexmask.long.byte 0x0 24.--27. 1. "DECORN,DECO Revision Number" newline hexmask.long.byte 0x0 12.--15. 1. "ZARN,ZUC Authentication Hardware Accelerator Revision Number" newline hexmask.long.byte 0x0 8.--11. 1. "ZERN,ZUC Encryption Hardware Accelerator Revision Number" newline hexmask.long.byte 0x0 4.--7. 1. "SNW9RN,SNOW-f9 Hardware Accelerator Revision Number" newline hexmask.long.byte 0x0 0.--3. 1. "CRCRN,CRC Hardware Accelerator Revision Number" line.long 0x4 "CRNR_LS,CHA Revision Number Register. least-significant half" hexmask.long.byte 0x4 28.--31. 1. "PKRN,Public Key Hardware Accelerator Revision Number For PKHA-XT PKRN=1. For PKHA-SD see below." newline hexmask.long.byte 0x4 24.--27. 1. "KASRN,Kasumi f8/f9 Hardware Accelerator Revision Number" newline hexmask.long.byte 0x4 20.--23. 1. "SNW8RN,SNOW-f8 Hardware Accelerator Revision Number" newline hexmask.long.byte 0x4 16.--19. 1. "RNGRN,Random Number Generator Revision Number." newline hexmask.long.byte 0x4 12.--15. 1. "MDRN,Message Digest Hardware Accelerator module Revision Number." newline hexmask.long.byte 0x4 4.--7. 1. "DESRN,DES Accelerator Revision Number." newline hexmask.long.byte 0x4 0.--3. 1. "AESRN,AES Accelerator Revision Number" line.long 0x8 "CTPR_MS,Compile Time Parameters Register. most-significant half" hexmask.long.byte 0x8 28.--31. 1. "AXI_PIPE_DEPTH,AXI Pipeline Depth" newline bitfld.long 0x8 27. "AXI_LIODN,LIODN logic included" "0,1" newline bitfld.long 0x8 26. "AXI_PRI,AXI Master Priority implemented" "0,1" newline bitfld.long 0x8 25. "QI,Queue Manager interface (QI) implemented" "0,1" newline bitfld.long 0x8 24. "ACC_CTL,System/user partition-based CAAM IP Bus register access control 0: CAAM does not implement partition-based access control for its IP Bus registers i" "0: CAAM does not implement partition-based access..,?" newline bitfld.long 0x8 23. "C1C2,Separate C1 and C2 registers 0: In this implementation of CAAM the Class 2 Key and Context registers are shared with the Class 1 Key and Context registers" "0: In this implementation of CAAM the Class 2 Key..,?" newline bitfld.long 0x8 21. "PC,Performance Counter registers implemented 0: CAAM does not implement Performance Counter registers" "0: CAAM does not implement Performance Counter..,?" newline bitfld.long 0x8 20. "DECO_WD,DECO Watchdog Counter implemented 0: CAAM does not implement a DECO Watchdog Counter" "0: CAAM does not implement a DECO Watchdog Counter,?" newline bitfld.long 0x8 19. "PM_EVT_BUS,Performance Monitor Event Bus implemented 0: CAAM does not implement a Performance Monitor Event Bus" "0: CAAM does not implement a Performance Monitor..,?" newline bitfld.long 0x8 18. "SG8,Eight Scatter-Gather Tables implemented 0: CAAM implements one Scatter-Gather Table register" "0: CAAM implements one Scatter-Gather Table register,?" newline bitfld.long 0x8 17. "MCFG_PS,Pointer Size field implemented 0: The Master Configuration Register does not contain a Pointer Size field" "0: The Master Configuration Register does not..,?" newline bitfld.long 0x8 16. "MCFG_BURST,Burst Configurability If MCFG_BURST is 0 the normal burst size is limited to 32 bytes and large bursts cannot be enabled" "0,1" newline bitfld.long 0x8 14. "IP_CLK,IP Bus Slave Clock" "0,1" newline bitfld.long 0x8 13. "DPAA2,ICIDs with AMQs supported" "0,1" newline bitfld.long 0x8 11. "AI_INCL,AIOP interface implemented" "0,1" newline bitfld.long 0x8 8.--10. "RNG_I,RNG Instantiations" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 4. "REG_PG_SIZE,CAAM register page size. 0: CAAM uses 4Kbyte register pages. 1: CAAM uses 64Kbyte register pages." "0: CAAM uses 4Kbyte register pages,1: CAAM uses 64Kbyte register pages" newline bitfld.long 0x8 1. "VIRT_EN_POR_VALUE,Job Ring Virtualization POR state" "0,1" newline bitfld.long 0x8 0. "VIRT_EN_INCL,Job Ring Virtualization programmable" "0,1" line.long 0xC "CTPR_LS,Compile Time Parameters Register. least-significant half" bitfld.long 0xC 14. "DKP,Derived Key Protocol" "0: CAAM does not implement the Derived Key Protocol.,1: CAAM implements the Derived Key Protocol." newline bitfld.long 0xC 13. "MAN_PROT,Manufacturing Protection protocol" "0: CAAM does not implement Manufacturing Protection..,1: CAAM implements Manufacturing Protection.." newline bitfld.long 0xC 12. "DBL_CRC,Double CRC protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for Double.." newline bitfld.long 0xC 11. "P3G_LTE,3GPP/LTE protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for 3G and.." newline bitfld.long 0xC 10. "RSA,RSA protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for RSA.." newline bitfld.long 0xC 9. "MACSEC,MACSEC protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the.." newline bitfld.long 0xC 8. "TLS_PRF,TLS PRF protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the TLS.." newline bitfld.long 0xC 7. "SSL_TLS,SSL/TLS protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the SSL.." newline bitfld.long 0xC 6. "IKE,IKE protocols" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the IKE.." newline bitfld.long 0xC 5. "IPSEC,IPSEC protocols" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the.." newline bitfld.long 0xC 4. "SRTP,SRTP protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the SRTP.." newline bitfld.long 0xC 3. "WIMAX,WiMax protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the.." newline bitfld.long 0xC 2. "WIFI,WiFi protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for the WIFI.." newline bitfld.long 0xC 1. "BLOB,Blob protocol" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for.." newline bitfld.long 0xC 0. "KG_DS,PK generation and digital signature protcols" "0: CAAM does not implement specialized support for..,1: CAAM implements specialized support for Public.." rgroup.long 0xFB4++0x3 line.long 0x0 "SMSTA,Secure Memory Status Register" hexmask.long.byte 0x0 28.--31. 1. "PART,Partition" newline hexmask.long.word 0x0 16.--26. 1. "PAGE,Page" newline bitfld.long 0x0 15. "SMR_WP,Secure Memory Registers Write Protected" "0,1" newline bitfld.long 0x0 12. "NS,The TrustZone nonsecure bit of the bus master whose access to Secure Memory was denied" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "DID,The DID of the bus master whose access to Secure Memory was denied." newline hexmask.long.byte 0x0 4.--7. 1. "ACCERR,Access Error" newline hexmask.long.byte 0x0 0.--3. 1. "STATE,Current State. This field represents the current state of the Secure Memory Controller." rgroup.long 0xFBC++0x3 line.long 0x0 "SMPO,Secure Memory Partition Owners Register" bitfld.long 0x0 30.--31. "PO15,Partition Owner for partition 15. See PO0." "0,1,2,3" newline bitfld.long 0x0 28.--29. "PO14,Partition Owner for partition 14. See PO0." "0,1,2,3" newline bitfld.long 0x0 26.--27. "PO13,Partition Owner for partition 13. See PO0." "0,1,2,3" newline bitfld.long 0x0 24.--25. "PO12,Partition Owner for partition 12. See PO0." "0,1,2,3" newline bitfld.long 0x0 22.--23. "PO11,Partition Owner for partition 11. See PO0." "0,1,2,3" newline bitfld.long 0x0 20.--21. "PO10,Partition Owner for partition 10. See PO0." "0,1,2,3" newline bitfld.long 0x0 18.--19. "PO9,Partition Owner for partition 9. See PO0." "0,1,2,3" newline bitfld.long 0x0 16.--17. "PO8,Partition Owner for partition 8. See PO0." "0,1,2,3" newline bitfld.long 0x0 14.--15. "PO7,Partition Owner for partition 7. See PO0." "0,1,2,3" newline bitfld.long 0x0 12.--13. "PO6,Partition Owner for partition 6. See PO0." "0,1,2,3" newline bitfld.long 0x0 10.--11. "PO5,Partition Owner for partition 5. See PO0." "0,1,2,3" newline bitfld.long 0x0 8.--9. "PO4,Partition Owner for partition 4. See PO0." "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO3,Partition Owner for partition 3. See PO0." "0,1,2,3" newline bitfld.long 0x0 4.--5. "PO2,Partition Owner for partition 2. See PO0." "0,1,2,3" newline bitfld.long 0x0 2.--3. "PO1,Partition Owner for partition 1. See PO0." "0,1,2,3" newline bitfld.long 0x0 0.--1. "PO0,Partition Owner for partition 0: When read by a Job Ring owner this field indicates if partition 0 is owned by that Job Ring another Job Ring Unowned or Unimplemented" "0: When read by a Job Ring owner,1: Partition 0 does not exist in this version,2: Another entity owns partition 0. Partition 0 is..,3: The entity that read the SMPO register owns.." rgroup.quad 0xFC0++0x7 line.quad 0x0 "FAR,Fault Address Register" hexmask.quad 0x0 0.--35. 1. "FAR,Fault Address" rgroup.long 0xFC8++0x7 line.long 0x0 "FADID,Fault Address DID Register" hexmask.long.word 0x0 5.--15. 1. "FICID,DMA transaction ICID. This was the ICID value associated with the DMA transaction that failed." newline bitfld.long 0x0 4. "FNS,DMA transaction ns" "0,1" newline hexmask.long.byte 0x0 0.--3. 1. "FDID,DMA transaction DID. This was the DID associated with the DMA transaction that failed." line.long 0x4 "FADR,Fault Address Detail Register" bitfld.long 0x4 30.--31. "FERR,Fault Error Code. This is the AXI Error Response Code." "0: OKAY - Normal Access,?,2: SLVERR - Slave Error,3: DECERR - Decode Error" newline bitfld.long 0x4 28. "FNS,Non-secure (AXI bus ns bit) access to Secure Memory." "0: CAAM DMA was asserting ns=0 at the time of the..,1: CAAM DMA was asserting ns=1 at the time of the.." newline bitfld.long 0x4 27. "FBNDG,Access permission binding access to Secure Memory." "0: CAAM DMA was not reading access permissions from..,1: CAAM DMA was reading access permissions from a.." newline bitfld.long 0x4 26. "FTDSC,Trusted Descriptor access to Secure Memory" "0: CAAM DMA was not executing a Trusted Descriptor..,1: CAAM DMA was executing a Trusted Descriptor at.." newline bitfld.long 0x4 25. "FKEY,Key Access Read" "0: CAAM DMA was not attempting to perform a key..,1: CAAM DMA was attempting to perform a key read.." newline bitfld.long 0x4 24. "FKMOD,Key Modifier Read" "0: CAAM DMA was not attempting to read the key..,1: CAAM DMA was attempting to read the key modifier.." newline bitfld.long 0x4 16.--18. "FSZ_EXT,AXI Transaction Transfer Size - extended" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 15. "DTYP,Data Type. The type of data being processed when the AXI transfer error occurred." "0: message data,1: control data" newline bitfld.long 0x4 12.--14. "JSRC,Job Source. The source of the job whose AXI transfer ended with an error:" "0: Job Ring 0,1: Job Ring 1,2: Job Ring 2,3: Job Ring 3,4: RTIC,?,?,?" newline hexmask.long.byte 0x4 8.--11. 1. "BLKID,Block ID" newline bitfld.long 0x4 7. "TYP,AXI Transaction Type" "0: Read.,1: Write." newline hexmask.long.byte 0x4 0.--6. 1. "FSZ,AXI Transaction Transfer Size" rgroup.long 0xFD4++0x2B line.long 0x0 "CSTA,CAAM Status Register" bitfld.long 0x0 10. "PLEND,Platform Endianness" "0: Platform default is Little Endian,1: Platform default is Big Endian" newline bitfld.long 0x0 8.--9. "MOO,Mode of Operation" "0: Non-Secure,1: Secure,2: Trusted,3: Fail" newline bitfld.long 0x0 2. "TRNG_IDLE,TRNG Idle" "0,1" newline bitfld.long 0x0 1. "IDLE,CAAM Idle" "0,1" newline bitfld.long 0x0 0. "BSY,CAAM Busy" "0,1" line.long 0x4 "SMVID_MS,Secure Memory Version ID Register. most-significant half" hexmask.long.word 0x4 16.--25. 1. "MAX_NPAG,Maximum allowable value for NPAG" newline hexmask.long.byte 0x4 12.--15. 1. "NPRT,This is the highest numbered Secure Memory partition so there can be 1 to 16 partitions." newline hexmask.long.word 0x4 0.--9. 1. "NPAG,This is the highest numbered page of Secure Memory" line.long 0x8 "SMVID_LS,Secure Memory Version ID Register. least-significant half" bitfld.long 0x8 16.--18. "PSIZ,Page Size" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 8.--15. 1. "SMJV,Secure Memory Major Version ID" newline hexmask.long.byte 0x8 0.--7. 1. "SMNV,Secure Memory Minor Version ID." line.long 0xC "RVID,RTIC Version ID Register" bitfld.long 0xC 27. "MD,Memory Block D Available" "0,1" newline bitfld.long 0xC 26. "MC,Memory Block C Available" "0,1" newline bitfld.long 0xC 25. "MB,Memory Block B Available" "0,1" newline bitfld.long 0xC 24. "MA,Memory Block A Available" "0,1" newline bitfld.long 0xC 19. "SHA_512,SHA-512." "0: RTIC cannot use the SHA-512 hashing algorithm.,1: RTIC can use the SHA-512 hashing algorithm." newline bitfld.long 0xC 17. "SHA_256,SHA-256." "0: RTIC cannot use the SHA-256 hashing algorithm.,1: RTIC can use the SHA-256 hashing algorithm." newline hexmask.long.byte 0xC 8.--15. 1. "RMJV,RTIC Major Version" newline hexmask.long.byte 0xC 0.--7. 1. "RMNV,RTIC Minor Version" line.long 0x10 "CCBVID,CHA Cluster Block Version ID Register" hexmask.long.byte 0x10 24.--31. 1. "CAAM_ERA,CAAM Era. This version of CAAM is based on Era 9 RTL. A value of 0 implies CAAM Era 5 or earlier." newline hexmask.long.byte 0x10 8.--15. 1. "AMJV,Accelerator Major Revision Number" newline hexmask.long.byte 0x10 0.--7. 1. "AMNV,Accelerator Minor Revision Number" line.long 0x14 "CHAVID_MS,CHA Version ID Register. most-significant half" hexmask.long.byte 0x14 28.--31. 1. "JRVID,Job Ring Version ID" newline hexmask.long.byte 0x14 24.--27. 1. "DECOVID,DECO Version ID" newline hexmask.long.byte 0x14 12.--15. 1. "ZAVID,ZUC Authentication Hardware Accelerator Version ID" newline hexmask.long.byte 0x14 8.--11. 1. "ZEVID,ZUC Encryption Hardware Accelerator Version ID" newline hexmask.long.byte 0x14 4.--7. 1. "SNW9VID,SNOW-f9 Hardware Accelerator Version ID" newline hexmask.long.byte 0x14 0.--3. 1. "CRCVID,CRC Hardware Accelerator Version ID" line.long 0x18 "CHAVID_LS,CHA Version ID Register. least-significant half" hexmask.long.byte 0x18 28.--31. 1. "PKVID,Public Key Hardware Accelerator Version ID" newline hexmask.long.byte 0x18 24.--27. 1. "KASVID,Kasumi f8/f9 Hardware Accelerator Version ID." newline hexmask.long.byte 0x18 20.--23. 1. "SNW8VID,SNOW-f8 Hardware Accelerator Version ID." newline hexmask.long.byte 0x18 16.--19. 1. "RNGVID,Random Number Generator Version ID." newline hexmask.long.byte 0x18 12.--15. 1. "MDVID,Message Digest Hardware Accelerator Version ID." newline hexmask.long.byte 0x18 4.--7. 1. "DESVID,DES Accelerator Version ID." newline hexmask.long.byte 0x18 0.--3. 1. "AESVID,AES Accelerator Version ID." line.long 0x1C "CHANUM_MS,CHA Number Register. most-significant half" hexmask.long.byte 0x1C 28.--31. 1. "JRNUM,The number of copies of the Job Ring that are implemented in this version of CAAM" newline hexmask.long.byte 0x1C 24.--27. 1. "DECONUM,The number of copies of the DECO that are implemented in this version of CAAM" newline hexmask.long.byte 0x1C 12.--15. 1. "ZANUM,The number of copies of ZUCA that are implemented in this version of CAAM" newline hexmask.long.byte 0x1C 8.--11. 1. "ZENUM,The number of copies of ZUCE that are implemented in this version of CAAM" newline hexmask.long.byte 0x1C 4.--7. 1. "SNW9NUM,The number of copies of the SNOW-f9 module that are implemented in this version of CAAM" newline hexmask.long.byte 0x1C 0.--3. 1. "CRCNUM,The number of copies of the CRC module that are implemented in this version of CAAM" line.long 0x20 "CHANUM_LS,CHA Number Register. least-significant half" hexmask.long.byte 0x20 28.--31. 1. "PKNUM,The number of copies of the Public Key module that are implemented in this version of CAAM" newline hexmask.long.byte 0x20 24.--27. 1. "KASNUM,The number of copies of the Kasumi module that are implemented in this version of CAAM" newline hexmask.long.byte 0x20 20.--23. 1. "SNW8NUM,The number of copies of the SNOW-f8 module that are implemented in this version of CAAM" newline hexmask.long.byte 0x20 16.--19. 1. "RNGNUM,The number of copies of the Random Number Generator that are implemented in this version of CAAM." newline hexmask.long.byte 0x20 12.--15. 1. "MDNUM,The number of copies of the MDHA (Hashing module) that are implemented in this version of CAAM." newline hexmask.long.byte 0x20 8.--11. 1. "ARC4NUM,The number of copies of the ARC4 module that are implemented in this version of CAAM." newline hexmask.long.byte 0x20 4.--7. 1. "DESNUM,The number of copies of the DES module that are implemented in this version of CAAM." newline hexmask.long.byte 0x20 0.--3. 1. "AESNUM,The number of copies of the AES module that are implemented in this version of CAAM." line.long 0x24 "CAAMVID_MS,CAAM Version ID Register. most-significant half" hexmask.long.word 0x24 16.--31. 1. "IP_ID,ID for CAAM." newline hexmask.long.byte 0x24 8.--15. 1. "MAJ_REV,Major revision number for CAAM." newline hexmask.long.byte 0x24 0.--7. 1. "MIN_REV,Minor revision number for CAAM." line.long 0x28 "CAAMVID_LS,CAAM Version ID Register. least-significant half" hexmask.long.byte 0x28 24.--31. 1. "COMPILE_OPT,Compile options for CAAM." newline hexmask.long.byte 0x28 16.--23. 1. "INTG_OPT,Integration options for CAAM." newline hexmask.long.byte 0x28 8.--15. 1. "ECO_REV,ECO revision for CAAM." newline hexmask.long.byte 0x28 0.--7. 1. "CONFIG_OPT,Configuration options for CAAM." group.quad 0x10000++0x7 line.quad 0x0 "IRBAR_JR0,Input Ring Base Address Register for Job Ring 0" hexmask.quad 0x0 0.--35. 1. "IRBA,Input Ring Base Address." group.long 0x1000C++0x3 line.long 0x0 "IRSR_JR0,Input Ring Size Register for Job Ring 0" hexmask.long.word 0x0 0.--9. 1. "IRS,Input Ring Size. (measured in number of entries)" group.long 0x10014++0x3 line.long 0x0 "IRSAR_JR0,Input Ring Slots Available Register for Job Ring 0" hexmask.long.word 0x0 0.--9. 1. "IRSA,Input Ring Slots Available. (measured in number of available job slots)" group.long 0x1001C++0x3 line.long 0x0 "IRJAR_JR0,Input Ring Jobs Added Register for Job Ring0" hexmask.long.word 0x0 0.--9. 1. "IRJA,Input Ring Jobs Added. (measured in number of entries)" group.quad 0x10020++0x7 line.quad 0x0 "ORBAR_JR0,Output Ring Base Address Register for Job Ring 0" hexmask.quad 0x0 0.--35. 1. "ORBA,Output Ring Base Address." group.long 0x1002C++0x3 line.long 0x0 "ORSR_JR0,Output Ring Size Register for Job Ring 0" hexmask.long.word 0x0 0.--9. 1. "ORS,Output Ring Size. (measured in number of entries)" group.long 0x10034++0x3 line.long 0x0 "ORJRR_JR0,Output Ring Jobs Removed Register for Job Ring 0" hexmask.long.word 0x0 0.--9. 1. "ORJR,Output Ring Jobs Removed. (measured in number of entries)" group.long 0x1003C++0x3 line.long 0x0 "ORSFR_JR0,Output Ring Slots Full Register for Job Ring 0" hexmask.long.word 0x0 0.--9. 1. "ORSF,Output Ring Slots Full. (measured in number of entries)" rgroup.long 0x10044++0x3 line.long 0x0 "JRSTAR_JR0,Job Ring Output Status Register for Job Ring 0" hexmask.long.byte 0x0 28.--31. 1. "SSRC,Status source. These bits define which source is reporting the status. All other values - reserved" newline hexmask.long 0x0 0.--27. 1. "SSED,Source-specific error details" group.long 0x1004C++0xB line.long 0x0 "JRINTR_JR0,Job Ring Interrupt Status Register for Job Ring 0" hexmask.long.word 0x0 16.--29. 1. "ERR_ORWI,Output ring write index with error" newline hexmask.long.byte 0x0 8.--12. 1. "ERR_TYPE,Error type" newline eventfld.long 0x0 5. "EXIT_FAIL,Exit SNVS Fail State" "0,1" newline eventfld.long 0x0 4. "ENTER_FAIL,Enter SNVS Fail State" "0,1" newline eventfld.long 0x0 2.--3. "HALT,Halt the Job Ring" "0,1,2,3" newline eventfld.long 0x0 1. "JRE,Job Ring Error" "0,1" newline eventfld.long 0x0 0. "JRI,Job Ring Interrupt" "0,1" line.long 0x4 "JRCFGR_JR0_MS,Job Ring Configuration Register for Job Ring 0. most-significant half" bitfld.long 0x4 30. "INCL_SEQ_OUT,Include Sequence Out Length" "0,1" newline bitfld.long 0x4 29. "FAIL_MODE,Fail mode control" "0,1" newline bitfld.long 0x4 18. "DWSO,Double Word Swap Override" "0,1" newline bitfld.long 0x4 17. "PEO,Platform Endian Override - The bit is XORed with the PLEND bit in the CaCSTA Register and the other 'swap' bits in the Job Ring Configuration Register to determine the AXI Master's view of memory endianness when executing Job Descriptors from this.." "0,1" newline bitfld.long 0x4 16. "DMBS,Descriptor Message Data Byte Swap (this applies only to internal message data transfers to/from DECO Descriptor Buffers)" "0,1" newline bitfld.long 0x4 14. "CWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 13. "CHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 12. "CBSO,To assist with mixed Endianness platforms this bit configures a byte swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 10. "MWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 9. "MHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 8. "MBSO,To assist with mixed Endianness platforms this bit configures a byte swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 6. "CWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 5. "CHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 4. "CBSI,To assist with mixed Endianness platforms this bit configures a byte swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 2. "MWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 1. "MHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 0. "MBSI,To assist with mixed Endianness platforms this bit configures a byte swap of message data read by CAAM DMA" "0,1" line.long 0x8 "JRCFGR_JR0_LS,Job Ring Configuration Register for Job Ring 0. least-significant half" hexmask.long.word 0x8 16.--31. 1. "ICTT,Interrupt Coalescing Timer Threshold" newline hexmask.long.byte 0x8 8.--15. 1. "ICDCT,Interrupt Coalescing Descriptor Count Threshold" newline bitfld.long 0x8 1. "ICEN,Interrupt Coalescing Enable." "0: Interrupt coalescing is disabled. If the IMSK..,1: Interrupt coalescing is enabled. If the IMSK bit.." newline bitfld.long 0x8 0. "IMSK,Interrupt Mask. Mask the interrupt that is associated with the particular processor." "0: Interrupt enabled.,1: Interrupt masked." group.long 0x1005C++0x3 line.long 0x0 "IRRIR_JR0,Input Ring Read Index Register for Job Ring 0" hexmask.long.word 0x0 0.--12. 1. "IRRI,Input Ring Read Index." group.long 0x10064++0x3 line.long 0x0 "ORWIR_JR0,Output Ring Write Index Register for Job Ring 0" hexmask.long.word 0x0 0.--13. 1. "ORWI,Output Ring Write Index. The pointer to the next entry in the output ring." wgroup.long 0x1006C++0x3 line.long 0x0 "JRCR_JR0,Job Ring Command Register for Job Ring 0" bitfld.long 0x0 1. "PARK,Park - When PARK is 0 software writes a 1 to PARK to request that the Job Ring be 'parked' i" "0,1" newline bitfld.long 0x0 0. "RESET,Reset - When RESET is 0 software writes a 1 to RESET to request a flush of the Job Ring" "0,1" rgroup.long 0x10704++0x3 line.long 0x0 "JR0AAV,Job Ring 0 Address-Array Valid Register" bitfld.long 0x0 31. "BC,Been Changed" "0,1" newline bitfld.long 0x0 3. "V3,Valid 3" "0,1" newline bitfld.long 0x0 2. "V2,Valid 2" "0,1" newline bitfld.long 0x0 1. "V1,Valid 1" "0,1" newline bitfld.long 0x0 0. "V0,Valid 0" "0,1" rgroup.quad 0x10800++0x1F line.quad 0x0 "JR0AAA0,Job Ring 0 Address-Array Address 0 Register" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x8 "JR0AAA1,Job Ring 0 Address-Array Address 1 Register" hexmask.quad 0x8 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x10 "JR0AAA2,Job Ring 0 Address-Array Address 2 Register" hexmask.quad 0x10 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x18 "JR0AAA3,Job Ring 0 Address-Array Address 3 Register" hexmask.quad 0x18 0.--35. 1. "JD_ADDR,Job Descriptor Address." rgroup.long 0x10A00++0x3 line.long 0x0 "P0SDID_JR0,Partition 0 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A04++0xB line.long 0x0 "P0SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P0SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P0SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A10++0x3 line.long 0x0 "P1SDID_JR0,Partition 1 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A14++0xB line.long 0x0 "P1SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P1SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P1SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A20++0x3 line.long 0x0 "P2SDID_JR0,Partition 2 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A24++0xB line.long 0x0 "P2SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P2SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P2SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A30++0x3 line.long 0x0 "P3SDID_JR0,Partition 3 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A34++0xB line.long 0x0 "P3SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P3SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P3SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A40++0x3 line.long 0x0 "P4SDID_JR0,Partition 4 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A44++0xB line.long 0x0 "P4SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P4SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P4SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A50++0x3 line.long 0x0 "P5SDID_JR0,Partition 5 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A54++0xB line.long 0x0 "P5SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P5SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P5SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A60++0x3 line.long 0x0 "P6SDID_JR0,Partition 6 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A64++0xB line.long 0x0 "P6SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P6SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P6SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A70++0x3 line.long 0x0 "P7SDID_JR0,Partition 7 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A74++0xB line.long 0x0 "P7SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P7SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P7SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A80++0x3 line.long 0x0 "P8SDID_JR0,Partition 8 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A84++0xB line.long 0x0 "P8SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P8SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P8SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10A90++0x3 line.long 0x0 "P9SDID_JR0,Partition 9 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10A94++0xB line.long 0x0 "P9SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P9SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P9SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AA0++0x3 line.long 0x0 "P10SDID_JR0,Partition 10 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AA4++0xB line.long 0x0 "P10SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P10SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P10SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AB0++0x3 line.long 0x0 "P11SDID_JR0,Partition 11 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AB4++0xB line.long 0x0 "P11SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P11SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P11SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AC0++0x3 line.long 0x0 "P12SDID_JR0,Partition 12 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AC4++0xB line.long 0x0 "P12SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P12SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P12SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AD0++0x3 line.long 0x0 "P13SDID_JR0,Partition 13 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AD4++0xB line.long 0x0 "P13SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P13SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P13SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AE0++0x3 line.long 0x0 "P14SDID_JR0,Partition 14 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AE4++0xB line.long 0x0 "P14SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P14SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P14SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x10AF0++0x3 line.long 0x0 "P15SDID_JR0,Partition 15 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x10AF4++0xB line.long 0x0 "P15SMAPR_JR0,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P15SMAG2_JR0,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P15SMAG1_JR0,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" wgroup.long 0x10BE4++0x3 line.long 0x0 "SMCR_JR0,Secure Memory Command Register" hexmask.long.word 0x0 16.--31. 1. "PAGE,This is the number of the page to be referenced in field CMD" newline hexmask.long.byte 0x0 8.--11. 1. "PRTN,Partition: When an Allocate Page or De-allocate Partition command is issued the action is performed on the partition indicated in the PRTN field" newline hexmask.long.byte 0x0 0.--3. 1. "CMD,Command: 1h: Allocate Page - This command allocates the page specified in the PAGE field to the partition specified in the PRTN field" rgroup.long 0x10BEC++0x3 line.long 0x0 "SMCSR_JR0,Secure Memory Command Status Register" hexmask.long.word 0x0 16.--27. 1. "PAGE,Page" newline bitfld.long 0x0 14.--15. "CERR,Command Error" "0: No Error.,1: Command has not yet completed.,2: A security failure occurred.,3: Command Overflow. Another command was issued by.." newline bitfld.long 0x0 12.--13. "AERR,Allocation Error" "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO,Page Owner: Following a Page Inquiry Command this field indicates if the Page is owned by the entity that issued the inquiry owned by another entity or unowned" "0: Available; Unowned: The entity that issued the..,1: Page does not exist in this version or is not..,2: Another entity owns the page. This page is..,3: Owned by the entity making the inquiry. The.." newline hexmask.long.byte 0x0 0.--3. 1. "PRTN,Following a Page Inquiry Command if the PO field is 10 or 11 this field indicates the partition to which the page specified in the PAGE field is allocated" rgroup.long 0x10E00++0x3 line.long 0x0 "REIR0JR0,Recoverable Error Interrupt Record 0 for Job Ring 0" bitfld.long 0x0 31. "MISS,If MISS=1 a second recoverable error associated with JR occurred before REIR0JR was written following a previous JR recoverable error" "0,1" newline bitfld.long 0x0 24.--25. "TYPE,This field indicates the type of the recoverable error" "0,1,2,3" rgroup.quad 0x10E08++0x7 line.quad 0x0 "REIR2JR0,Recoverable Error Interrupt Record 2 for Job Ring 0" hexmask.quad 0x0 0.--35. 1. "ADDR,Address associated with the recoverable JR error." rgroup.long 0x10E10++0x7 line.long 0x0 "REIR4JR0,Recoverable Error Interrupt Record 4 for Job Ring 0" bitfld.long 0x0 30.--31. "MIX,This field holds the memory interface index associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 28.--29. "ERR,This field holds the AXI error response associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 23. "RWB,This field specifies whether the memory access was a read or write." "0,1" newline bitfld.long 0x0 20.--22. "AXPROT,This field holds the AXI protection transaction attribute used for the memory access." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 16.--19. 1. "AXCACHE,This field holds the AXI cache control transaction attribute used for the memory access." newline hexmask.long.byte 0x0 11.--14. 1. "DID,This field holds the DID associated with the recoverable error." newline hexmask.long.word 0x0 0.--10. 1. "ICID,This field holds the ICID associated with the recoverable error." line.long 0x4 "REIR5JR0,Recoverable Error Interrupt Record 5 for Job Ring 0" bitfld.long 0x4 29. "SMA,This field indicates whether the bus transaction associated with the recoverable error was an attempted access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 28. "KEY,This field indicates whether the bus transaction associated with the recoverable error was an attempted key access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 27. "KMOD,This field indicates whether the bus transaction associated with the recoverable error was an attempt to read the key modifier associated with an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 26. "TDSC,This field indicates whether the bus transaction associated with the recoverable error was an attempt to assert trusted descriptor privilege when accessing an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 25. "BNDG,This field indicates whether the bus transaction associated with the recoverable error was initiating an CAAM Secure Memory blob operation" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "BID,This field holds the block identifier (see Internal Block ID) of the source of the AXI transaction associated with the recoverable error" group.quad 0x20000++0x7 line.quad 0x0 "IRBAR_JR1,Input Ring Base Address Register for Job Ring 1" hexmask.quad 0x0 0.--35. 1. "IRBA,Input Ring Base Address." group.long 0x2000C++0x3 line.long 0x0 "IRSR_JR1,Input Ring Size Register for Job Ring 1" hexmask.long.word 0x0 0.--9. 1. "IRS,Input Ring Size. (measured in number of entries)" group.long 0x20014++0x3 line.long 0x0 "IRSAR_JR1,Input Ring Slots Available Register for Job Ring 1" hexmask.long.word 0x0 0.--9. 1. "IRSA,Input Ring Slots Available. (measured in number of available job slots)" group.long 0x2001C++0x3 line.long 0x0 "IRJAR_JR1,Input Ring Jobs Added Register for Job Ring1" hexmask.long.word 0x0 0.--9. 1. "IRJA,Input Ring Jobs Added. (measured in number of entries)" group.quad 0x20020++0x7 line.quad 0x0 "ORBAR_JR1,Output Ring Base Address Register for Job Ring 1" hexmask.quad 0x0 0.--35. 1. "ORBA,Output Ring Base Address." group.long 0x2002C++0x3 line.long 0x0 "ORSR_JR1,Output Ring Size Register for Job Ring 1" hexmask.long.word 0x0 0.--9. 1. "ORS,Output Ring Size. (measured in number of entries)" group.long 0x20034++0x3 line.long 0x0 "ORJRR_JR1,Output Ring Jobs Removed Register for Job Ring 1" hexmask.long.word 0x0 0.--9. 1. "ORJR,Output Ring Jobs Removed. (measured in number of entries)" group.long 0x2003C++0x3 line.long 0x0 "ORSFR_JR1,Output Ring Slots Full Register for Job Ring 1" hexmask.long.word 0x0 0.--9. 1. "ORSF,Output Ring Slots Full. (measured in number of entries)" rgroup.long 0x20044++0x3 line.long 0x0 "JRSTAR_JR1,Job Ring Output Status Register for Job Ring 1" hexmask.long.byte 0x0 28.--31. 1. "SSRC,Status source. These bits define which source is reporting the status. All other values - reserved" newline hexmask.long 0x0 0.--27. 1. "SSED,Source-specific error details" group.long 0x2004C++0xB line.long 0x0 "JRINTR_JR1,Job Ring Interrupt Status Register for Job Ring 1" hexmask.long.word 0x0 16.--29. 1. "ERR_ORWI,Output ring write index with error" newline hexmask.long.byte 0x0 8.--12. 1. "ERR_TYPE,Error type" newline eventfld.long 0x0 5. "EXIT_FAIL,Exit SNVS Fail State" "0,1" newline eventfld.long 0x0 4. "ENTER_FAIL,Enter SNVS Fail State" "0,1" newline eventfld.long 0x0 2.--3. "HALT,Halt the Job Ring" "0,1,2,3" newline eventfld.long 0x0 1. "JRE,Job Ring Error" "0,1" newline eventfld.long 0x0 0. "JRI,Job Ring Interrupt" "0,1" line.long 0x4 "JRCFGR_JR1_MS,Job Ring Configuration Register for Job Ring 1. most-significant half" bitfld.long 0x4 30. "INCL_SEQ_OUT,Include Sequence Out Length" "0,1" newline bitfld.long 0x4 29. "FAIL_MODE,Fail mode control" "0,1" newline bitfld.long 0x4 18. "DWSO,Double Word Swap Override" "0,1" newline bitfld.long 0x4 17. "PEO,Platform Endian Override - The bit is XORed with the PLEND bit in the CaCSTA Register and the other 'swap' bits in the Job Ring Configuration Register to determine the AXI Master's view of memory endianness when executing Job Descriptors from this.." "0,1" newline bitfld.long 0x4 16. "DMBS,Descriptor Message Data Byte Swap (this applies only to internal message data transfers to/from DECO Descriptor Buffers)" "0,1" newline bitfld.long 0x4 14. "CWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 13. "CHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 12. "CBSO,To assist with mixed Endianness platforms this bit configures a byte swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 10. "MWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 9. "MHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 8. "MBSO,To assist with mixed Endianness platforms this bit configures a byte swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 6. "CWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 5. "CHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 4. "CBSI,To assist with mixed Endianness platforms this bit configures a byte swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 2. "MWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 1. "MHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 0. "MBSI,To assist with mixed Endianness platforms this bit configures a byte swap of message data read by CAAM DMA" "0,1" line.long 0x8 "JRCFGR_JR1_LS,Job Ring Configuration Register for Job Ring 1. least-significant half" hexmask.long.word 0x8 16.--31. 1. "ICTT,Interrupt Coalescing Timer Threshold" newline hexmask.long.byte 0x8 8.--15. 1. "ICDCT,Interrupt Coalescing Descriptor Count Threshold" newline bitfld.long 0x8 1. "ICEN,Interrupt Coalescing Enable." "0: Interrupt coalescing is disabled. If the IMSK..,1: Interrupt coalescing is enabled. If the IMSK bit.." newline bitfld.long 0x8 0. "IMSK,Interrupt Mask. Mask the interrupt that is associated with the particular processor." "0: Interrupt enabled.,1: Interrupt masked." group.long 0x2005C++0x3 line.long 0x0 "IRRIR_JR1,Input Ring Read Index Register for Job Ring 1" hexmask.long.word 0x0 0.--12. 1. "IRRI,Input Ring Read Index." group.long 0x20064++0x3 line.long 0x0 "ORWIR_JR1,Output Ring Write Index Register for Job Ring 1" hexmask.long.word 0x0 0.--13. 1. "ORWI,Output Ring Write Index. The pointer to the next entry in the output ring." wgroup.long 0x2006C++0x3 line.long 0x0 "JRCR_JR1,Job Ring Command Register for Job Ring 1" bitfld.long 0x0 1. "PARK,Park - When PARK is 0 software writes a 1 to PARK to request that the Job Ring be 'parked' i" "0,1" newline bitfld.long 0x0 0. "RESET,Reset - When RESET is 0 software writes a 1 to RESET to request a flush of the Job Ring" "0,1" rgroup.long 0x20704++0x3 line.long 0x0 "JR1AAV,Job Ring 1 Address-Array Valid Register" bitfld.long 0x0 31. "BC,Been Changed" "0,1" newline bitfld.long 0x0 3. "V3,Valid 3" "0,1" newline bitfld.long 0x0 2. "V2,Valid 2" "0,1" newline bitfld.long 0x0 1. "V1,Valid 1" "0,1" newline bitfld.long 0x0 0. "V0,Valid 0" "0,1" rgroup.quad 0x20800++0x1F line.quad 0x0 "JR1AAA0,Job Ring 1 Address-Array Address 0 Register" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x8 "JR1AAA1,Job Ring 1 Address-Array Address 1 Register" hexmask.quad 0x8 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x10 "JR1AAA2,Job Ring 1 Address-Array Address 2 Register" hexmask.quad 0x10 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x18 "JR1AAA3,Job Ring 1 Address-Array Address 3 Register" hexmask.quad 0x18 0.--35. 1. "JD_ADDR,Job Descriptor Address." rgroup.long 0x20A00++0x3 line.long 0x0 "P0SDID_JR1,Partition 0 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A04++0xB line.long 0x0 "P0SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P0SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P0SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A10++0x3 line.long 0x0 "P1SDID_JR1,Partition 1 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A14++0xB line.long 0x0 "P1SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P1SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P1SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A20++0x3 line.long 0x0 "P2SDID_JR1,Partition 2 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A24++0xB line.long 0x0 "P2SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P2SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P2SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A30++0x3 line.long 0x0 "P3SDID_JR1,Partition 3 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A34++0xB line.long 0x0 "P3SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P3SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P3SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A40++0x3 line.long 0x0 "P4SDID_JR1,Partition 4 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A44++0xB line.long 0x0 "P4SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P4SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P4SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A50++0x3 line.long 0x0 "P5SDID_JR1,Partition 5 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A54++0xB line.long 0x0 "P5SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P5SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P5SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A60++0x3 line.long 0x0 "P6SDID_JR1,Partition 6 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A64++0xB line.long 0x0 "P6SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P6SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P6SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A70++0x3 line.long 0x0 "P7SDID_JR1,Partition 7 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A74++0xB line.long 0x0 "P7SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P7SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P7SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A80++0x3 line.long 0x0 "P8SDID_JR1,Partition 8 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A84++0xB line.long 0x0 "P8SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P8SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P8SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20A90++0x3 line.long 0x0 "P9SDID_JR1,Partition 9 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20A94++0xB line.long 0x0 "P9SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P9SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P9SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AA0++0x3 line.long 0x0 "P10SDID_JR1,Partition 10 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AA4++0xB line.long 0x0 "P10SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P10SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P10SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AB0++0x3 line.long 0x0 "P11SDID_JR1,Partition 11 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AB4++0xB line.long 0x0 "P11SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P11SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P11SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AC0++0x3 line.long 0x0 "P12SDID_JR1,Partition 12 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AC4++0xB line.long 0x0 "P12SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P12SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P12SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AD0++0x3 line.long 0x0 "P13SDID_JR1,Partition 13 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AD4++0xB line.long 0x0 "P13SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P13SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P13SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AE0++0x3 line.long 0x0 "P14SDID_JR1,Partition 14 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AE4++0xB line.long 0x0 "P14SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P14SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P14SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x20AF0++0x3 line.long 0x0 "P15SDID_JR1,Partition 15 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x20AF4++0xB line.long 0x0 "P15SMAPR_JR1,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P15SMAG2_JR1,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P15SMAG1_JR1,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" wgroup.long 0x20BE4++0x3 line.long 0x0 "SMCR_JR1,Secure Memory Command Register" hexmask.long.word 0x0 16.--31. 1. "PAGE,This is the number of the page to be referenced in field CMD" newline hexmask.long.byte 0x0 8.--11. 1. "PRTN,Partition: When an Allocate Page or De-allocate Partition command is issued the action is performed on the partition indicated in the PRTN field" newline hexmask.long.byte 0x0 0.--3. 1. "CMD,Command: 1h: Allocate Page - This command allocates the page specified in the PAGE field to the partition specified in the PRTN field" rgroup.long 0x20BEC++0x3 line.long 0x0 "SMCSR_JR1,Secure Memory Command Status Register" hexmask.long.word 0x0 16.--27. 1. "PAGE,Page" newline bitfld.long 0x0 14.--15. "CERR,Command Error" "0: No Error.,1: Command has not yet completed.,2: A security failure occurred.,3: Command Overflow. Another command was issued by.." newline bitfld.long 0x0 12.--13. "AERR,Allocation Error" "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO,Page Owner: Following a Page Inquiry Command this field indicates if the Page is owned by the entity that issued the inquiry owned by another entity or unowned" "0: Available; Unowned: The entity that issued the..,1: Page does not exist in this version or is not..,2: Another entity owns the page. This page is..,3: Owned by the entity making the inquiry. The.." newline hexmask.long.byte 0x0 0.--3. 1. "PRTN,Following a Page Inquiry Command if the PO field is 10 or 11 this field indicates the partition to which the page specified in the PAGE field is allocated" rgroup.long 0x20E00++0x3 line.long 0x0 "REIR0JR1,Recoverable Error Interrupt Record 0 for Job Ring 1" bitfld.long 0x0 31. "MISS,If MISS=1 a second recoverable error associated with JR occurred before REIR0JR was written following a previous JR recoverable error" "0,1" newline bitfld.long 0x0 24.--25. "TYPE,This field indicates the type of the recoverable error" "0,1,2,3" rgroup.quad 0x20E08++0x7 line.quad 0x0 "REIR2JR1,Recoverable Error Interrupt Record 2 for Job Ring 1" hexmask.quad 0x0 0.--35. 1. "ADDR,Address associated with the recoverable JR error." rgroup.long 0x20E10++0x7 line.long 0x0 "REIR4JR1,Recoverable Error Interrupt Record 4 for Job Ring 1" bitfld.long 0x0 30.--31. "MIX,This field holds the memory interface index associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 28.--29. "ERR,This field holds the AXI error response associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 23. "RWB,This field specifies whether the memory access was a read or write." "0,1" newline bitfld.long 0x0 20.--22. "AXPROT,This field holds the AXI protection transaction attribute used for the memory access." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 16.--19. 1. "AXCACHE,This field holds the AXI cache control transaction attribute used for the memory access." newline hexmask.long.byte 0x0 11.--14. 1. "DID,This field holds the DID associated with the recoverable error." newline hexmask.long.word 0x0 0.--10. 1. "ICID,This field holds the ICID associated with the recoverable error." line.long 0x4 "REIR5JR1,Recoverable Error Interrupt Record 5 for Job Ring 1" bitfld.long 0x4 29. "SMA,This field indicates whether the bus transaction associated with the recoverable error was an attempted access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 28. "KEY,This field indicates whether the bus transaction associated with the recoverable error was an attempted key access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 27. "KMOD,This field indicates whether the bus transaction associated with the recoverable error was an attempt to read the key modifier associated with an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 26. "TDSC,This field indicates whether the bus transaction associated with the recoverable error was an attempt to assert trusted descriptor privilege when accessing an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 25. "BNDG,This field indicates whether the bus transaction associated with the recoverable error was initiating an CAAM Secure Memory blob operation" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "BID,This field holds the block identifier (see Internal Block ID) of the source of the AXI transaction associated with the recoverable error" group.quad 0x30000++0x7 line.quad 0x0 "IRBAR_JR2,Input Ring Base Address Register for Job Ring 2" hexmask.quad 0x0 0.--35. 1. "IRBA,Input Ring Base Address." group.long 0x3000C++0x3 line.long 0x0 "IRSR_JR2,Input Ring Size Register for Job Ring 2" hexmask.long.word 0x0 0.--9. 1. "IRS,Input Ring Size. (measured in number of entries)" group.long 0x30014++0x3 line.long 0x0 "IRSAR_JR2,Input Ring Slots Available Register for Job Ring 2" hexmask.long.word 0x0 0.--9. 1. "IRSA,Input Ring Slots Available. (measured in number of available job slots)" group.long 0x3001C++0x3 line.long 0x0 "IRJAR_JR2,Input Ring Jobs Added Register for Job Ring2" hexmask.long.word 0x0 0.--9. 1. "IRJA,Input Ring Jobs Added. (measured in number of entries)" group.quad 0x30020++0x7 line.quad 0x0 "ORBAR_JR2,Output Ring Base Address Register for Job Ring 2" hexmask.quad 0x0 0.--35. 1. "ORBA,Output Ring Base Address." group.long 0x3002C++0x3 line.long 0x0 "ORSR_JR2,Output Ring Size Register for Job Ring 2" hexmask.long.word 0x0 0.--9. 1. "ORS,Output Ring Size. (measured in number of entries)" group.long 0x30034++0x3 line.long 0x0 "ORJRR_JR2,Output Ring Jobs Removed Register for Job Ring 2" hexmask.long.word 0x0 0.--9. 1. "ORJR,Output Ring Jobs Removed. (measured in number of entries)" group.long 0x3003C++0x3 line.long 0x0 "ORSFR_JR2,Output Ring Slots Full Register for Job Ring 2" hexmask.long.word 0x0 0.--9. 1. "ORSF,Output Ring Slots Full. (measured in number of entries)" rgroup.long 0x30044++0x3 line.long 0x0 "JRSTAR_JR2,Job Ring Output Status Register for Job Ring 2" hexmask.long.byte 0x0 28.--31. 1. "SSRC,Status source. These bits define which source is reporting the status. All other values - reserved" newline hexmask.long 0x0 0.--27. 1. "SSED,Source-specific error details" group.long 0x3004C++0xB line.long 0x0 "JRINTR_JR2,Job Ring Interrupt Status Register for Job Ring 2" hexmask.long.word 0x0 16.--29. 1. "ERR_ORWI,Output ring write index with error" newline hexmask.long.byte 0x0 8.--12. 1. "ERR_TYPE,Error type" newline eventfld.long 0x0 5. "EXIT_FAIL,Exit SNVS Fail State" "0,1" newline eventfld.long 0x0 4. "ENTER_FAIL,Enter SNVS Fail State" "0,1" newline eventfld.long 0x0 2.--3. "HALT,Halt the Job Ring" "0,1,2,3" newline eventfld.long 0x0 1. "JRE,Job Ring Error" "0,1" newline eventfld.long 0x0 0. "JRI,Job Ring Interrupt" "0,1" line.long 0x4 "JRCFGR_JR2_MS,Job Ring Configuration Register for Job Ring 2. most-significant half" bitfld.long 0x4 30. "INCL_SEQ_OUT,Include Sequence Out Length" "0,1" newline bitfld.long 0x4 29. "FAIL_MODE,Fail mode control" "0,1" newline bitfld.long 0x4 18. "DWSO,Double Word Swap Override" "0,1" newline bitfld.long 0x4 17. "PEO,Platform Endian Override - The bit is XORed with the PLEND bit in the CaCSTA Register and the other 'swap' bits in the Job Ring Configuration Register to determine the AXI Master's view of memory endianness when executing Job Descriptors from this.." "0,1" newline bitfld.long 0x4 16. "DMBS,Descriptor Message Data Byte Swap (this applies only to internal message data transfers to/from DECO Descriptor Buffers)" "0,1" newline bitfld.long 0x4 14. "CWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 13. "CHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 12. "CBSO,To assist with mixed Endianness platforms this bit configures a byte swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 10. "MWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 9. "MHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 8. "MBSO,To assist with mixed Endianness platforms this bit configures a byte swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 6. "CWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 5. "CHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 4. "CBSI,To assist with mixed Endianness platforms this bit configures a byte swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 2. "MWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 1. "MHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 0. "MBSI,To assist with mixed Endianness platforms this bit configures a byte swap of message data read by CAAM DMA" "0,1" line.long 0x8 "JRCFGR_JR2_LS,Job Ring Configuration Register for Job Ring 2. least-significant half" hexmask.long.word 0x8 16.--31. 1. "ICTT,Interrupt Coalescing Timer Threshold" newline hexmask.long.byte 0x8 8.--15. 1. "ICDCT,Interrupt Coalescing Descriptor Count Threshold" newline bitfld.long 0x8 1. "ICEN,Interrupt Coalescing Enable." "0: Interrupt coalescing is disabled. If the IMSK..,1: Interrupt coalescing is enabled. If the IMSK bit.." newline bitfld.long 0x8 0. "IMSK,Interrupt Mask. Mask the interrupt that is associated with the particular processor." "0: Interrupt enabled.,1: Interrupt masked." group.long 0x3005C++0x3 line.long 0x0 "IRRIR_JR2,Input Ring Read Index Register for Job Ring 2" hexmask.long.word 0x0 0.--12. 1. "IRRI,Input Ring Read Index." group.long 0x30064++0x3 line.long 0x0 "ORWIR_JR2,Output Ring Write Index Register for Job Ring 2" hexmask.long.word 0x0 0.--13. 1. "ORWI,Output Ring Write Index. The pointer to the next entry in the output ring." wgroup.long 0x3006C++0x3 line.long 0x0 "JRCR_JR2,Job Ring Command Register for Job Ring 2" bitfld.long 0x0 1. "PARK,Park - When PARK is 0 software writes a 1 to PARK to request that the Job Ring be 'parked' i" "0,1" newline bitfld.long 0x0 0. "RESET,Reset - When RESET is 0 software writes a 1 to RESET to request a flush of the Job Ring" "0,1" rgroup.long 0x30704++0x3 line.long 0x0 "JR2AAV,Job Ring 2 Address-Array Valid Register" bitfld.long 0x0 31. "BC,Been Changed" "0,1" newline bitfld.long 0x0 3. "V3,Valid 3" "0,1" newline bitfld.long 0x0 2. "V2,Valid 2" "0,1" newline bitfld.long 0x0 1. "V1,Valid 1" "0,1" newline bitfld.long 0x0 0. "V0,Valid 0" "0,1" rgroup.quad 0x30800++0x1F line.quad 0x0 "JR2AAA0,Job Ring 2 Address-Array Address 0 Register" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x8 "JR2AAA1,Job Ring 2 Address-Array Address 1 Register" hexmask.quad 0x8 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x10 "JR2AAA2,Job Ring 2 Address-Array Address 2 Register" hexmask.quad 0x10 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x18 "JR2AAA3,Job Ring 2 Address-Array Address 3 Register" hexmask.quad 0x18 0.--35. 1. "JD_ADDR,Job Descriptor Address." rgroup.long 0x30A00++0x3 line.long 0x0 "P0SDID_JR2,Partition 0 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A04++0xB line.long 0x0 "P0SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P0SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P0SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A10++0x3 line.long 0x0 "P1SDID_JR2,Partition 1 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A14++0xB line.long 0x0 "P1SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P1SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P1SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A20++0x3 line.long 0x0 "P2SDID_JR2,Partition 2 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A24++0xB line.long 0x0 "P2SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P2SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P2SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A30++0x3 line.long 0x0 "P3SDID_JR2,Partition 3 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A34++0xB line.long 0x0 "P3SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P3SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P3SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A40++0x3 line.long 0x0 "P4SDID_JR2,Partition 4 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A44++0xB line.long 0x0 "P4SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P4SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P4SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A50++0x3 line.long 0x0 "P5SDID_JR2,Partition 5 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A54++0xB line.long 0x0 "P5SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P5SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P5SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A60++0x3 line.long 0x0 "P6SDID_JR2,Partition 6 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A64++0xB line.long 0x0 "P6SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P6SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P6SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A70++0x3 line.long 0x0 "P7SDID_JR2,Partition 7 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A74++0xB line.long 0x0 "P7SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P7SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P7SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A80++0x3 line.long 0x0 "P8SDID_JR2,Partition 8 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A84++0xB line.long 0x0 "P8SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P8SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P8SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30A90++0x3 line.long 0x0 "P9SDID_JR2,Partition 9 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30A94++0xB line.long 0x0 "P9SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P9SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P9SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AA0++0x3 line.long 0x0 "P10SDID_JR2,Partition 10 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AA4++0xB line.long 0x0 "P10SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P10SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P10SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AB0++0x3 line.long 0x0 "P11SDID_JR2,Partition 11 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AB4++0xB line.long 0x0 "P11SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P11SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P11SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AC0++0x3 line.long 0x0 "P12SDID_JR2,Partition 12 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AC4++0xB line.long 0x0 "P12SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P12SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P12SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AD0++0x3 line.long 0x0 "P13SDID_JR2,Partition 13 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AD4++0xB line.long 0x0 "P13SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P13SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P13SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AE0++0x3 line.long 0x0 "P14SDID_JR2,Partition 14 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AE4++0xB line.long 0x0 "P14SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P14SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P14SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x30AF0++0x3 line.long 0x0 "P15SDID_JR2,Partition 15 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x30AF4++0xB line.long 0x0 "P15SMAPR_JR2,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P15SMAG2_JR2,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P15SMAG1_JR2,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" wgroup.long 0x30BE4++0x3 line.long 0x0 "SMCR_JR2,Secure Memory Command Register" hexmask.long.word 0x0 16.--31. 1. "PAGE,This is the number of the page to be referenced in field CMD" newline hexmask.long.byte 0x0 8.--11. 1. "PRTN,Partition: When an Allocate Page or De-allocate Partition command is issued the action is performed on the partition indicated in the PRTN field" newline hexmask.long.byte 0x0 0.--3. 1. "CMD,Command: 1h: Allocate Page - This command allocates the page specified in the PAGE field to the partition specified in the PRTN field" rgroup.long 0x30BEC++0x3 line.long 0x0 "SMCSR_JR2,Secure Memory Command Status Register" hexmask.long.word 0x0 16.--27. 1. "PAGE,Page" newline bitfld.long 0x0 14.--15. "CERR,Command Error" "0: No Error.,1: Command has not yet completed.,2: A security failure occurred.,3: Command Overflow. Another command was issued by.." newline bitfld.long 0x0 12.--13. "AERR,Allocation Error" "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO,Page Owner: Following a Page Inquiry Command this field indicates if the Page is owned by the entity that issued the inquiry owned by another entity or unowned" "0: Available; Unowned: The entity that issued the..,1: Page does not exist in this version or is not..,2: Another entity owns the page. This page is..,3: Owned by the entity making the inquiry. The.." newline hexmask.long.byte 0x0 0.--3. 1. "PRTN,Following a Page Inquiry Command if the PO field is 10 or 11 this field indicates the partition to which the page specified in the PAGE field is allocated" rgroup.long 0x30E00++0x3 line.long 0x0 "REIR0JR2,Recoverable Error Interrupt Record 0 for Job Ring 2" bitfld.long 0x0 31. "MISS,If MISS=1 a second recoverable error associated with JR occurred before REIR0JR was written following a previous JR recoverable error" "0,1" newline bitfld.long 0x0 24.--25. "TYPE,This field indicates the type of the recoverable error" "0,1,2,3" rgroup.quad 0x30E08++0x7 line.quad 0x0 "REIR2JR2,Recoverable Error Interrupt Record 2 for Job Ring 2" hexmask.quad 0x0 0.--35. 1. "ADDR,Address associated with the recoverable JR error." rgroup.long 0x30E10++0x7 line.long 0x0 "REIR4JR2,Recoverable Error Interrupt Record 4 for Job Ring 2" bitfld.long 0x0 30.--31. "MIX,This field holds the memory interface index associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 28.--29. "ERR,This field holds the AXI error response associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 23. "RWB,This field specifies whether the memory access was a read or write." "0,1" newline bitfld.long 0x0 20.--22. "AXPROT,This field holds the AXI protection transaction attribute used for the memory access." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 16.--19. 1. "AXCACHE,This field holds the AXI cache control transaction attribute used for the memory access." newline hexmask.long.byte 0x0 11.--14. 1. "DID,This field holds the DID associated with the recoverable error." newline hexmask.long.word 0x0 0.--10. 1. "ICID,This field holds the ICID associated with the recoverable error." line.long 0x4 "REIR5JR2,Recoverable Error Interrupt Record 5 for Job Ring 2" bitfld.long 0x4 29. "SMA,This field indicates whether the bus transaction associated with the recoverable error was an attempted access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 28. "KEY,This field indicates whether the bus transaction associated with the recoverable error was an attempted key access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 27. "KMOD,This field indicates whether the bus transaction associated with the recoverable error was an attempt to read the key modifier associated with an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 26. "TDSC,This field indicates whether the bus transaction associated with the recoverable error was an attempt to assert trusted descriptor privilege when accessing an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 25. "BNDG,This field indicates whether the bus transaction associated with the recoverable error was initiating an CAAM Secure Memory blob operation" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "BID,This field holds the block identifier (see Internal Block ID) of the source of the AXI transaction associated with the recoverable error" group.quad 0x40000++0x7 line.quad 0x0 "IRBAR_JR3,Input Ring Base Address Register for Job Ring 3" hexmask.quad 0x0 0.--35. 1. "IRBA,Input Ring Base Address." group.long 0x4000C++0x3 line.long 0x0 "IRSR_JR3,Input Ring Size Register for Job Ring 3" hexmask.long.word 0x0 0.--9. 1. "IRS,Input Ring Size. (measured in number of entries)" group.long 0x40014++0x3 line.long 0x0 "IRSAR_JR3,Input Ring Slots Available Register for Job Ring 3" hexmask.long.word 0x0 0.--9. 1. "IRSA,Input Ring Slots Available. (measured in number of available job slots)" group.long 0x4001C++0x3 line.long 0x0 "IRJAR_JR3,Input Ring Jobs Added Register for Job Ring3" hexmask.long.word 0x0 0.--9. 1. "IRJA,Input Ring Jobs Added. (measured in number of entries)" group.quad 0x40020++0x7 line.quad 0x0 "ORBAR_JR3,Output Ring Base Address Register for Job Ring 3" hexmask.quad 0x0 0.--35. 1. "ORBA,Output Ring Base Address." group.long 0x4002C++0x3 line.long 0x0 "ORSR_JR3,Output Ring Size Register for Job Ring 3" hexmask.long.word 0x0 0.--9. 1. "ORS,Output Ring Size. (measured in number of entries)" group.long 0x40034++0x3 line.long 0x0 "ORJRR_JR3,Output Ring Jobs Removed Register for Job Ring 3" hexmask.long.word 0x0 0.--9. 1. "ORJR,Output Ring Jobs Removed. (measured in number of entries)" group.long 0x4003C++0x3 line.long 0x0 "ORSFR_JR3,Output Ring Slots Full Register for Job Ring 3" hexmask.long.word 0x0 0.--9. 1. "ORSF,Output Ring Slots Full. (measured in number of entries)" rgroup.long 0x40044++0x3 line.long 0x0 "JRSTAR_JR3,Job Ring Output Status Register for Job Ring 3" hexmask.long.byte 0x0 28.--31. 1. "SSRC,Status source. These bits define which source is reporting the status. All other values - reserved" newline hexmask.long 0x0 0.--27. 1. "SSED,Source-specific error details" group.long 0x4004C++0xB line.long 0x0 "JRINTR_JR3,Job Ring Interrupt Status Register for Job Ring 3" hexmask.long.word 0x0 16.--29. 1. "ERR_ORWI,Output ring write index with error" newline hexmask.long.byte 0x0 8.--12. 1. "ERR_TYPE,Error type" newline eventfld.long 0x0 5. "EXIT_FAIL,Exit SNVS Fail State" "0,1" newline eventfld.long 0x0 4. "ENTER_FAIL,Enter SNVS Fail State" "0,1" newline eventfld.long 0x0 2.--3. "HALT,Halt the Job Ring" "0,1,2,3" newline eventfld.long 0x0 1. "JRE,Job Ring Error" "0,1" newline eventfld.long 0x0 0. "JRI,Job Ring Interrupt" "0,1" line.long 0x4 "JRCFGR_JR3_MS,Job Ring Configuration Register for Job Ring 3. most-significant half" bitfld.long 0x4 30. "INCL_SEQ_OUT,Include Sequence Out Length" "0,1" newline bitfld.long 0x4 29. "FAIL_MODE,Fail mode control" "0,1" newline bitfld.long 0x4 18. "DWSO,Double Word Swap Override" "0,1" newline bitfld.long 0x4 17. "PEO,Platform Endian Override - The bit is XORed with the PLEND bit in the CaCSTA Register and the other 'swap' bits in the Job Ring Configuration Register to determine the AXI Master's view of memory endianness when executing Job Descriptors from this.." "0,1" newline bitfld.long 0x4 16. "DMBS,Descriptor Message Data Byte Swap (this applies only to internal message data transfers to/from DECO Descriptor Buffers)" "0,1" newline bitfld.long 0x4 14. "CWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 13. "CHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 12. "CBSO,To assist with mixed Endianness platforms this bit configures a byte swap of control data written by CAAM DMA" "0,1" newline bitfld.long 0x4 10. "MWSO,To assist with mixed Endianness platforms this bit configures a fullword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 9. "MHWSO,To assist with mixed Endianness platforms this bit configures a halfword swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 8. "MBSO,To assist with mixed Endianness platforms this bit configures a byte swap of message data written by CAAM DMA" "0,1" newline bitfld.long 0x4 6. "CWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 5. "CHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 4. "CBSI,To assist with mixed Endianness platforms this bit configures a byte swap of control data read by CAAM DMA" "0,1" newline bitfld.long 0x4 2. "MWSI,To assist with mixed Endianness platforms this bit configures a fullword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 1. "MHWSI,To assist with mixed Endianness platforms this bit configures a halfword swap of message data read by CAAM DMA" "0,1" newline bitfld.long 0x4 0. "MBSI,To assist with mixed Endianness platforms this bit configures a byte swap of message data read by CAAM DMA" "0,1" line.long 0x8 "JRCFGR_JR3_LS,Job Ring Configuration Register for Job Ring 3. least-significant half" hexmask.long.word 0x8 16.--31. 1. "ICTT,Interrupt Coalescing Timer Threshold" newline hexmask.long.byte 0x8 8.--15. 1. "ICDCT,Interrupt Coalescing Descriptor Count Threshold" newline bitfld.long 0x8 1. "ICEN,Interrupt Coalescing Enable." "0: Interrupt coalescing is disabled. If the IMSK..,1: Interrupt coalescing is enabled. If the IMSK bit.." newline bitfld.long 0x8 0. "IMSK,Interrupt Mask. Mask the interrupt that is associated with the particular processor." "0: Interrupt enabled.,1: Interrupt masked." group.long 0x4005C++0x3 line.long 0x0 "IRRIR_JR3,Input Ring Read Index Register for Job Ring 3" hexmask.long.word 0x0 0.--12. 1. "IRRI,Input Ring Read Index." group.long 0x40064++0x3 line.long 0x0 "ORWIR_JR3,Output Ring Write Index Register for Job Ring 3" hexmask.long.word 0x0 0.--13. 1. "ORWI,Output Ring Write Index. The pointer to the next entry in the output ring." wgroup.long 0x4006C++0x3 line.long 0x0 "JRCR_JR3,Job Ring Command Register for Job Ring 3" bitfld.long 0x0 1. "PARK,Park - When PARK is 0 software writes a 1 to PARK to request that the Job Ring be 'parked' i" "0,1" newline bitfld.long 0x0 0. "RESET,Reset - When RESET is 0 software writes a 1 to RESET to request a flush of the Job Ring" "0,1" rgroup.long 0x40704++0x3 line.long 0x0 "JR3AAV,Job Ring 3 Address-Array Valid Register" bitfld.long 0x0 31. "BC,Been Changed" "0,1" newline bitfld.long 0x0 3. "V3,Valid 3" "0,1" newline bitfld.long 0x0 2. "V2,Valid 2" "0,1" newline bitfld.long 0x0 1. "V1,Valid 1" "0,1" newline bitfld.long 0x0 0. "V0,Valid 0" "0,1" rgroup.quad 0x40800++0x1F line.quad 0x0 "JR3AAA0,Job Ring 3 Address-Array Address 0 Register" hexmask.quad 0x0 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x8 "JR3AAA1,Job Ring 3 Address-Array Address 1 Register" hexmask.quad 0x8 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x10 "JR3AAA2,Job Ring 3 Address-Array Address 2 Register" hexmask.quad 0x10 0.--35. 1. "JD_ADDR,Job Descriptor Address." line.quad 0x18 "JR3AAA3,Job Ring 3 Address-Array Address 3 Register" hexmask.quad 0x18 0.--35. 1. "JD_ADDR,Job Descriptor Address." rgroup.long 0x40A00++0x3 line.long 0x0 "P0SDID_JR3,Partition 0 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A04++0xB line.long 0x0 "P0SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P0SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P0SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A10++0x3 line.long 0x0 "P1SDID_JR3,Partition 1 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A14++0xB line.long 0x0 "P1SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P1SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P1SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A20++0x3 line.long 0x0 "P2SDID_JR3,Partition 2 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A24++0xB line.long 0x0 "P2SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P2SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P2SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A30++0x3 line.long 0x0 "P3SDID_JR3,Partition 3 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A34++0xB line.long 0x0 "P3SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P3SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P3SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A40++0x3 line.long 0x0 "P4SDID_JR3,Partition 4 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A44++0xB line.long 0x0 "P4SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P4SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P4SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A50++0x3 line.long 0x0 "P5SDID_JR3,Partition 5 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A54++0xB line.long 0x0 "P5SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P5SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P5SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A60++0x3 line.long 0x0 "P6SDID_JR3,Partition 6 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A64++0xB line.long 0x0 "P6SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P6SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P6SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A70++0x3 line.long 0x0 "P7SDID_JR3,Partition 7 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A74++0xB line.long 0x0 "P7SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P7SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P7SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A80++0x3 line.long 0x0 "P8SDID_JR3,Partition 8 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A84++0xB line.long 0x0 "P8SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P8SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P8SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40A90++0x3 line.long 0x0 "P9SDID_JR3,Partition 9 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40A94++0xB line.long 0x0 "P9SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P9SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P9SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AA0++0x3 line.long 0x0 "P10SDID_JR3,Partition 10 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AA4++0xB line.long 0x0 "P10SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P10SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P10SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AB0++0x3 line.long 0x0 "P11SDID_JR3,Partition 11 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AB4++0xB line.long 0x0 "P11SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P11SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P11SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AC0++0x3 line.long 0x0 "P12SDID_JR3,Partition 12 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AC4++0xB line.long 0x0 "P12SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P12SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P12SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AD0++0x3 line.long 0x0 "P13SDID_JR3,Partition 13 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AD4++0xB line.long 0x0 "P13SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P13SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P13SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AE0++0x3 line.long 0x0 "P14SDID_JR3,Partition 14 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AE4++0xB line.long 0x0 "P14SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P14SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P14SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" rgroup.long 0x40AF0++0x3 line.long 0x0 "P15SDID_JR3,Partition 15 SDID register" hexmask.long.word 0x0 0.--15. 1. "SDID,Security Domain Identifier" group.long 0x40AF4++0xB line.long 0x0 "P15SMAPR_JR3,Secure Memory Access Permissions register" hexmask.long.word 0x0 16.--31. 1. "PARTITION_KMOD,The value in this field is used to modify the Blob Key Encryption Key when exporting cryptographic Blobs from or importing cryptographic Blobs to this partition" newline bitfld.long 0x0 15. "CSP,Critical Security Parameters" "0: The pages allocated to the partition will not be..,1: The pages allocated to the partition will be.." newline bitfld.long 0x0 14. "PSP,Public Security Parameters" "0: The partition and any of the pages allocated to..,1: The partition cannot be de-allocated and the.." newline bitfld.long 0x0 13. "SMAP_LCK,SMAP LOCK bit" "0: The SMAP register is unlocked. The partition..,1: The SMAP register is locked. The SMAP_LCK CSP.." newline bitfld.long 0x0 12. "SMAG_LCK,SMAG LOCK bit" "0: The SMAG2JR register and SMAG1JR register are..,1: The SMAG2JR register and SMAG1JR register are.." newline bitfld.long 0x0 7. "G2_SMBLOB,Access Group 2 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 6. "G2_TDO,Access Group 2 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 5. "G2_WRITE,Access Group 2 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 4. "G2_READ,Access Group 2 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." newline bitfld.long 0x0 3. "G1_SMBLOB,Access Group 1 Secure Memory Blobs" "0: Exporting or importing Secure Memory Blobs is..,1: Exporting or importing Secure Memory Blobs is.." newline bitfld.long 0x0 2. "G1_TDO,Access Group 1 Trusted Descriptor Override" "0: Trusted Descriptors have the same access..,1: Trusted Descriptors are allowed to override the.." newline bitfld.long 0x0 1. "G1_WRITE,Access Group 1 Write" "0: Writes are prohibited (except that Trusted..,1: Writes are allowed (but importing a Secure.." newline bitfld.long 0x0 0. "G1_READ,Access Group 1 Read" "0: Instruction fetches and reads are prohibited..,1: Instruction fetches and reads are allowed (but.." line.long 0x4 "P15SMAG2_JR3,Secure Memory Access Group Registers" bitfld.long 0x4 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x4 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x4 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" line.long 0x8 "P15SMAG1_JR3,Secure Memory Access Group Registers" bitfld.long 0x8 31. "Gx_ID31,Bit set to 1 indicates NonSecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 30. "Gx_ID30,Bit set to 1 indicates NonSecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 29. "Gx_ID29,Bit set to 1 indicates NonSecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 28. "Gx_ID28,Bit set to 1 indicates NonSecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 27. "Gx_ID27,Bit set to 1 indicates NonSecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 26. "Gx_ID26,Bit set to 1 indicates NonSecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 25. "Gx_ID25,Bit set to 1 indicates NonSecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 24. "Gx_ID24,Bit set to 1 indicates NonSecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 23. "Gx_ID23,Bit set to 1 indicates NonSecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 22. "Gx_ID22,Bit set to 1 indicates NonSecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 21. "Gx_ID21,Bit set to 1 indicates NonSecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 20. "Gx_ID20,Bit set to 1 indicates NonSecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 19. "Gx_ID19,Bit set to 1 indicates NonSecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 18. "Gx_ID18,Bit set to 1 indicates NonSecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 17. "Gx_ID17,Bit set to 1 indicates NonSecureWorld DID 01 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 16. "Gx_ID16,Bit set to 1 indicates NonSecureWorld DID 00 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 15. "Gx_ID15,Bit set to 1 indicates SecureWorld DID 15 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 14. "Gx_ID14,Bit set to 1 indicates SecureWorld DID 14 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 13. "Gx_ID13,Bit set to 1 indicates SecureWorld DID 13 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 12. "Gx_ID12,Bit set to 1 indicates SecureWorld DID 12 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 11. "Gx_ID11,Bit set to 1 indicates SecureWorld DID 11 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 10. "Gx_ID10,Bit set to 1 indicates SecureWorld DID 10 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 9. "Gx_ID09,Bit set to 1 indicates SecureWorld DID 09 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 8. "Gx_ID08,Bit set to 1 indicates SecureWorld DID 08 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 7. "Gx_ID07,Bit set to 1 indicates SecureWorld DID 07 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 6. "Gx_ID06,Bit set to 1 indicates SecureWorld DID 06 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 5. "Gx_ID05,Bit set to 1 indicates SecureWorld DID 05 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 4. "Gx_ID04,Bit set to 1 indicates SecureWorld DID 04 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 3. "Gx_ID03,Bit set to 1 indicates SecureWorld DID 03 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 2. "Gx_ID02,Bit set to 1 indicates SecureWorld DID 02 is a member of Access Group x (1 or 2)." "0,1" newline bitfld.long 0x8 1. "Gx_ID01,Bit set to 1 indicates SecureWorld DID 01 is a member of Access Group x." "0,1" newline bitfld.long 0x8 0. "Gx_ID00,Bit set to 1 indicates SecureWorld DID 00 is a member of Access Group x." "0,1" wgroup.long 0x40BE4++0x3 line.long 0x0 "SMCR_JR3,Secure Memory Command Register" hexmask.long.word 0x0 16.--31. 1. "PAGE,This is the number of the page to be referenced in field CMD" newline hexmask.long.byte 0x0 8.--11. 1. "PRTN,Partition: When an Allocate Page or De-allocate Partition command is issued the action is performed on the partition indicated in the PRTN field" newline hexmask.long.byte 0x0 0.--3. 1. "CMD,Command: 1h: Allocate Page - This command allocates the page specified in the PAGE field to the partition specified in the PRTN field" rgroup.long 0x40BEC++0x3 line.long 0x0 "SMCSR_JR3,Secure Memory Command Status Register" hexmask.long.word 0x0 16.--27. 1. "PAGE,Page" newline bitfld.long 0x0 14.--15. "CERR,Command Error" "0: No Error.,1: Command has not yet completed.,2: A security failure occurred.,3: Command Overflow. Another command was issued by.." newline bitfld.long 0x0 12.--13. "AERR,Allocation Error" "0,1,2,3" newline bitfld.long 0x0 6.--7. "PO,Page Owner: Following a Page Inquiry Command this field indicates if the Page is owned by the entity that issued the inquiry owned by another entity or unowned" "0: Available; Unowned: The entity that issued the..,1: Page does not exist in this version or is not..,2: Another entity owns the page. This page is..,3: Owned by the entity making the inquiry. The.." newline hexmask.long.byte 0x0 0.--3. 1. "PRTN,Following a Page Inquiry Command if the PO field is 10 or 11 this field indicates the partition to which the page specified in the PAGE field is allocated" rgroup.long 0x40E00++0x3 line.long 0x0 "REIR0JR3,Recoverable Error Interrupt Record 0 for Job Ring 3" bitfld.long 0x0 31. "MISS,If MISS=1 a second recoverable error associated with JR occurred before REIR0JR was written following a previous JR recoverable error" "0,1" newline bitfld.long 0x0 24.--25. "TYPE,This field indicates the type of the recoverable error" "0,1,2,3" rgroup.quad 0x40E08++0x7 line.quad 0x0 "REIR2JR3,Recoverable Error Interrupt Record 2 for Job Ring 3" hexmask.quad 0x0 0.--35. 1. "ADDR,Address associated with the recoverable JR error." rgroup.long 0x40E10++0x7 line.long 0x0 "REIR4JR3,Recoverable Error Interrupt Record 4 for Job Ring 3" bitfld.long 0x0 30.--31. "MIX,This field holds the memory interface index associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 28.--29. "ERR,This field holds the AXI error response associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 23. "RWB,This field specifies whether the memory access was a read or write." "0,1" newline bitfld.long 0x0 20.--22. "AXPROT,This field holds the AXI protection transaction attribute used for the memory access." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 16.--19. 1. "AXCACHE,This field holds the AXI cache control transaction attribute used for the memory access." newline hexmask.long.byte 0x0 11.--14. 1. "DID,This field holds the DID associated with the recoverable error." newline hexmask.long.word 0x0 0.--10. 1. "ICID,This field holds the ICID associated with the recoverable error." line.long 0x4 "REIR5JR3,Recoverable Error Interrupt Record 5 for Job Ring 3" bitfld.long 0x4 29. "SMA,This field indicates whether the bus transaction associated with the recoverable error was an attempted access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 28. "KEY,This field indicates whether the bus transaction associated with the recoverable error was an attempted key access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 27. "KMOD,This field indicates whether the bus transaction associated with the recoverable error was an attempt to read the key modifier associated with an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 26. "TDSC,This field indicates whether the bus transaction associated with the recoverable error was an attempt to assert trusted descriptor privilege when accessing an CAAM Secure Memory partition" "0,1" newline bitfld.long 0x4 25. "BNDG,This field indicates whether the bus transaction associated with the recoverable error was initiating an CAAM Secure Memory blob operation" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "BID,This field holds the block identifier (see Internal Block ID) of the source of the AXI transaction associated with the recoverable error" rgroup.long 0x60004++0x3 line.long 0x0 "RSTA,RTIC Status Register" bitfld.long 0x0 25.--26. "CS,RTIC Current State. Indicates the current state of the RTIC controller." "0: Idle State,1: Single Hash State,2: Run-time State,3: Error State" newline bitfld.long 0x0 19. "RTD,Run Time Blocks Disabled" "0,1" newline bitfld.long 0x0 18. "HOD,Hash Once Blocks Disabled" "0,1" newline bitfld.long 0x0 17. "ABH,All Blocks Hashed" "0,1" newline bitfld.long 0x0 16. "WE,RTIC Watchdog Error" "0: No RTIC Watchdog timer error has occurred.,1: RTIC Watchdog timer has expired prior to.." newline hexmask.long.byte 0x0 8.--11. 1. "AE,Address Error" newline hexmask.long.byte 0x0 4.--7. 1. "MIS,Memory Integrity Status" newline bitfld.long 0x0 3. "HE,Hashing Error" "0: Memory block contents authenticated.,1: Memory block hash doesn't match reference value." newline bitfld.long 0x0 2. "SV,Security Violation" "0: Memory block contents authenticated.,1: Memory block hash doesn't match reference value." newline bitfld.long 0x0 1. "HD,Hash Once Operation Completed (Hash Done)" "0: Boot authentication disabled,1: Authenticate code/generate reference hash value." newline bitfld.long 0x0 0. "BSY,RTIC Idle/Busy Status. When busy the RTIC cannot be written to." "0: RTIC Idle.,1: RTIC Busy." group.long 0x6000C++0x3 line.long 0x0 "RCMD,RTIC Command Register" bitfld.long 0x0 3. "RTD,Run Time Disable" "0: Allow Run Time Mode,1: Prevent Run Time Mode" newline bitfld.long 0x0 2. "RTC,Run time check" "0: Run-time checking disabled,1: Verify run-time memory blocks continually" newline bitfld.long 0x0 1. "HO,Hash once" "0: Boot authentication disabled,1: Authenticate code/generate reference hash value." newline bitfld.long 0x0 0. "CINT,Clear Interrupt" "0: Do not clear interrupt,1: Clear interrupt. This bit cannot be modified.." group.long 0x60014++0x3 line.long 0x0 "RCTL,RTIC Control Register" bitfld.long 0x0 20. "RIDLE,RTIC setting for the IPG_IDLE signal" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "RALG,RTIC Algorithm Select" newline hexmask.long.byte 0x0 12.--15. 1. "RTMU,Run Time Memory Unlock" newline hexmask.long.byte 0x0 8.--11. 1. "RTME,Run Time Memory Enable" newline hexmask.long.byte 0x0 4.--7. 1. "HOME,Hash Once Memory Enable" newline bitfld.long 0x0 1.--3. "RREQS,RTIC Request Size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0. "IE,Interrupt Enable" "0: Interrupts disabled,1: Interrupts enabled" group.long 0x6001C++0x3 line.long 0x0 "RTHR,RTIC Throttle Register" hexmask.long.word 0x0 0.--15. 1. "RTHR,Run Time Mode DMA Throttle" group.quad 0x60028++0x7 line.quad 0x0 "RWDOG,RTIC Watchdog Timer" hexmask.quad.long 0x0 0.--31. 1. "RWDOG,Run Time Watchdog Time-Out value" group.long 0x60034++0x3 line.long 0x0 "REND,RTIC Endian Register" hexmask.long.byte 0x0 12.--15. 1. "RWS,RTIC Word Swap" newline hexmask.long.byte 0x0 8.--11. 1. "RHWS,RTIC Half-Word Swap" newline hexmask.long.byte 0x0 4.--7. 1. "RBS,RTIC Byte Swap" newline hexmask.long.byte 0x0 0.--3. 1. "REPO,RTIC Endian Platform Override" rgroup.long 0x60E00++0x3 line.long 0x0 "REIR0RTIC,Recoverable Error Interrupt Record 0 for RTIC" bitfld.long 0x0 31. "MISS,If MISS=1 a second recoverable error associated with RTIC occurred before REIR0RTIC was written following a previous RTIC recoverable error" "0,1" newline bitfld.long 0x0 24.--25. "TYPE,This field indicates the type of the recoverable error" "0,1,2,3" rgroup.quad 0x60E08++0x7 line.quad 0x0 "REIR2RTIC,Recoverable Error Interrupt Record 2 for RTIC" hexmask.quad 0x0 0.--63. 1. "ADDR,This register holds the address associated with the recoverable RTIC error." rgroup.long 0x60E10++0x7 line.long 0x0 "REIR4RTIC,Recoverable Error Interrupt Record 4 for RTIC" bitfld.long 0x0 30.--31. "MIX,This field holds the memory interface index associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 28.--29. "ERR,This field holds the AXI error response associated with the recoverable error." "0,1,2,3" newline bitfld.long 0x0 23. "RWB,This field specifies whether the memory access was a read or write." "0,1" newline bitfld.long 0x0 20.--22. "AXPROT,This field holds the AXI protection transaction attribute used for the memory access." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 16.--19. 1. "AXCACHE,This field holds the AXI cache control transaction attribute used for the memory access." newline hexmask.long.byte 0x0 11.--14. 1. "DID,This field holds the DID associated with the recoverable error." newline hexmask.long.word 0x0 0.--10. 1. "ICID,This field holds the ICID associated with the recoverable error." line.long 0x4 "REIR5RTIC,Recoverable Error Interrupt Record 5 for RTIC" bitfld.long 0x4 25. "SMA,This field indicates whether the bus transaction associated with the recoverable error was an attempted access to CAAM Secure Memory" "0,1" newline bitfld.long 0x4 24. "SAFE,SAFE indicates whether the AXI transaction associated with the recoverable error was a 'safe' transaction" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "BID,This field holds the block identifier (see Internal Block ID) of the source of the AXI transaction associated with the recoverable error" group.long 0x80004++0x3 line.long 0x0 "C0C1MR,CCB 0 Class 1 Mode Register Format for Non-Public Key Algorithms" hexmask.long.byte 0x0 16.--23. 1. "ALG,Algorithm. This field specifies which algorithm is being selected." newline hexmask.long.word 0x0 4.--12. 1. "AAI,Additional Algorithm information" newline bitfld.long 0x0 2.--3. "AS,Algorithm State" "0: Update,1: Initialize,2: Finalize,3: Initialize/Finalize" newline bitfld.long 0x0 1. "ICV_TEST,ICV Checking / Test AESA fault detection" "0,1" newline bitfld.long 0x0 0. "ENC,Encrypt/Decrypt" "0: Decrypt.,1: Encrypt." group.long 0x80004++0x3 line.long 0x0 "C0C1MR_PK,CCB 0 Class 1 Mode Register Format for Public Key Algorithms" hexmask.long.byte 0x0 16.--19. 1. "PKHA_MODE_MS,PKHA_MODE most-significant 4 bits" newline hexmask.long.word 0x0 0.--11. 1. "PKHA_MODE_LS,PKHA_MODE least significant 12 bits" group.long 0x80004++0x3 line.long 0x0 "C0C1MR_RNG,CCB 0 Class 1 Mode Register Format for RNG4" hexmask.long.byte 0x0 16.--23. 1. "ALG,Algorithm. This field specifies which algorithm is being selected." newline bitfld.long 0x0 12. "SK,Secure Key" "0: The destination for the RNG data is specified by..,1: The RNG data will go to the JDKEKR TDKEKR and.." newline bitfld.long 0x0 11. "AI,Additional Input Included" "0: No additional entropy input has been provided.,1: Additional entropy input has been provided." newline bitfld.long 0x0 10. "PS,Personalization String Included" "0: No personalization string is included.,1: A personalization string is included." newline bitfld.long 0x0 9. "OBP,Odd Byte Parity" "0: No odd byte parity.,1: Generate random data with odd byte parity." newline bitfld.long 0x0 8. "NZB,NonZero bytes" "0: Generate random data with all-zero bytes..,1: Generate random data without any all-zero bytes." newline bitfld.long 0x0 4.--5. "SH,State Handle" "0: State Handle 0,1: State Handle 1,?,?" newline bitfld.long 0x0 2.--3. "AS,Algorithm State" "0,1,2,3" newline bitfld.long 0x0 1. "PR,Prediction Resistance" "0,1" newline bitfld.long 0x0 0. "TST,Test Mode Request" "0,1" group.long 0x8000C++0x3 line.long 0x0 "C0C1KSR,CCB 0 Class 1 Key Size Register" hexmask.long.byte 0x0 0.--6. 1. "C1KS,Class 1 Key Size. This is the size of a Class 1 Key measured in bytes" group.quad 0x80010++0x7 line.quad 0x0 "C0C1DSR,CCB 0 Class 1 Data Size Register" rbitfld.quad 0x0 61.--63. "NUMBITS,Class 1 Data Size Number of bits" "0,1,2,3,4,5,6,7" newline rbitfld.quad 0x0 32. "C1CY,Class 1 Data Size Carry" "0: No carry out of the C1 Data Size Reg.,1: There was a carry out of the C1 Data Size Reg." newline hexmask.quad.long 0x0 0.--31. 1. "C1DS,Class 1 Data Size" group.long 0x8001C++0x3 line.long 0x0 "C0C1ICVSR,CCB 0 Class 1 ICV Size Register" hexmask.long.byte 0x0 0.--4. 1. "C1ICVS,Class 1 ICV Size in Bytes." wgroup.long 0x80034++0x3 line.long 0x0 "C0CCTRL,CCB 0 CHA Control Register" bitfld.long 0x0 27. "UB,Unload the PKHA B Memory" "0: Don't unload the PKHA B Memory.,1: Unload the PKHA B Memory into OFIFO." newline bitfld.long 0x0 26. "UA,Unload the PKHA A Memory" "0: Don't unload the PKHA A Memory.,1: Unload the PKHA A Memory into OFIFO." newline bitfld.long 0x0 24. "UN,Unload the PKHA N Memory" "0: Don't unload the PKHA N Memory.,1: Unload the PKHA N Memory into OFIFO." newline bitfld.long 0x0 23. "UB3,Unload the PKHA B3 Memory" "0: Don't unload the PKHA B3 Memory.,1: Unload the PKHA B3 Memory into OFIFO." newline bitfld.long 0x0 22. "UB2,Unload the PKHA B2 Memory" "0: Don't unload the PKHA B2 Memory.,1: Unload the PKHA B2 Memory into OFIFO." newline bitfld.long 0x0 21. "UB1,Unload the PKHA B1 Memory" "0: Don't unload the PKHA B1 Memory.,1: Unload the PKHA B1 Memory into OFIFO." newline bitfld.long 0x0 20. "UB0,Unload the PKHA B0 Memory" "0: Don't unload the PKHA B0 Memory.,1: Unload the PKHA B0 Memory into OFIFO." newline bitfld.long 0x0 19. "UA3,Unload the PKHA A3 Memory" "0: Don't unload the PKHA A3 Memory.,1: Unload the PKHA A3 Memory into OFIFO." newline bitfld.long 0x0 18. "UA2,Unload the PKHA A2 Memory" "0: Don't unload the PKHA A2 Memory.,1: Unload the PKHA A2 Memory into OFIFO." newline bitfld.long 0x0 17. "UA1,Unload the PKHA A1 Memory" "0: Don't unload the PKHA A1 Memory.,1: Unload the PKHA A1 Memory into OFIFO." newline bitfld.long 0x0 16. "UA0,Unload the PKHA A0 Memory" "0: Don't unload the PKHA A0 Memory.,1: Unload the PKHA A0 Memory into OFIFO." newline bitfld.long 0x0 9. "RNG,Reset Random Number Generator. Writing a 1 to this bit resets the Random Number Generator." "0: Do Not Reset,1: Reset Random Number Generator Block." newline bitfld.long 0x0 8. "CRC,Reset CRCA. Writing a 1 to this bit resets the CRC Accelerator." "0: Do Not Reset,1: Reset CRC Accelerator" newline bitfld.long 0x0 7. "MD,Reset MDHA. Writing a 1 to this bit resets the Message Digest Hardware Accelerator." "0: Do Not Reset,1: Reset Message Digest Hardware Accelerator" newline bitfld.long 0x0 6. "PK,Reset PKHA. Writing a 1 to this bit resets the Public Key Hardware Accelerator." "0: Do Not Reset,1: Reset Public Key Hardware Accelerator" newline bitfld.long 0x0 2. "DES,Reset DESA. Writing a 1 to this bit resets the DES Accelerator." "0: Do Not Reset,1: Reset DES Accelerator" newline bitfld.long 0x0 1. "AES,Reset AESA. Writing a 1 to this bit resets the AES Accelerator." "0: Do Not Reset,1: Reset AES Accelerator" newline bitfld.long 0x0 0. "CCB,Reset CCB" "0: Do Not Reset,1: Reset CCB" group.long 0x8003C++0x3 line.long 0x0 "C0ICTL,CCB 0 Interrupt Control Register" rbitfld.long 0x0 25. "RNEI,RNG Error Interrupt asserted." "0: No RNG error detected,1: RNG error detected" newline rbitfld.long 0x0 24. "CEI,CRCA Error Interrupt asserted." "0: No CRCA error detected,1: CRCA error detected" newline rbitfld.long 0x0 23. "MEI,MDHA (hashing) Error Interrupt asserted." "0: No MDHA error detected,1: MDHA error detected" newline rbitfld.long 0x0 22. "PEI,PKHA (Public Key) Error Interrupt asserted." "0: No PKHA error detected,1: PKHA error detected" newline rbitfld.long 0x0 18. "DEI,DESA Error Interrupt asserted." "0: No DESA error detected,1: DESA error detected" newline rbitfld.long 0x0 17. "AEI,AESA Error Interrupt asserted." "0: No AESA error detected,1: AESA error detected" newline eventfld.long 0x0 9. "RNDI,RNG done interrupt" "0,1" newline eventfld.long 0x0 8. "CDI,CRCA done interrupt" "0,1" newline eventfld.long 0x0 7. "MDI,MDHA (hashing) done interrupt" "0,1" newline eventfld.long 0x0 6. "PDI,PKHA (Public Key) done interrupt" "0,1" newline eventfld.long 0x0 2. "DDI,DESA done interrupt" "0,1" newline eventfld.long 0x0 1. "ADI,AESA done interrupt" "0,1" wgroup.long 0x80044++0x3 line.long 0x0 "C0CWR,CCB 0 Clear Written Register" bitfld.long 0x0 31. "CIF,Clear Input FIFO (and NFIFO)" "0: Don't clear the IFIFO.,1: Clear the IFIFO." newline bitfld.long 0x0 30. "COF,Clear Output FIFO. Writing a 1 to this bit causes the Output FIFO to be cleared." "0: Don't clear the OFIFO.,1: Clear the OFIFO." newline bitfld.long 0x0 29. "C1RST,Reset Class 1 CHA" "0: Don't reset the Class 1 CHA.,1: Reset the Class 1 CHA." newline bitfld.long 0x0 28. "C2RST,Reset Class 2 CHA" "0: Don't reset the Class 2 CHA.,1: Reset the Class 2 CHA." newline bitfld.long 0x0 27. "C1D,Clear Class 1 Done Interrupt. Writing a 1 to this bit clears the Class 1 done interrupt." "0: Don't clear the Class 1 done interrrupt.,1: Clear the Class 1 done interrrupt." newline bitfld.long 0x0 26. "C2D,Clear Class 2 Done Interrupt. Writing a 1 to this bit clears the Class 2 done interrupt." "0: Don't clear the Class 2 done interrrupt.,1: Clear the Class 2 done interrrupt." newline bitfld.long 0x0 25. "CDS,Clear Descriptor Sharing signal" "0: Don't clear the shared descriptor signal.,1: Clear the shared descriptor signal." newline bitfld.long 0x0 22. "C2K,Clear the Class 2 Key Register" "0: Don't clear the Class 2 Key Register.,1: Clear the Class 2 Key Register." newline bitfld.long 0x0 21. "C2C,Clear the Class 2 Context Register" "0: Don't clear the Class 2 Context Register.,1: Clear the Class 2 Context Register." newline bitfld.long 0x0 18. "C2DS,Clear the Class 2 Data Size Registers" "0: Don't clear the Class 2 Data Size Register.,1: Clear the Class 2 Data Size Register." newline bitfld.long 0x0 16. "C2M,Clear the Class 2 Mode Register" "0: Don't clear the Class 2 Mode Register.,1: Clear the Class 2 Mode Register." newline bitfld.long 0x0 15. "CPKE,Clear the PKHA E Size Register" "0: Don't clear the PKHA E Size Register..,1: Clear the PKHA E Size Register." newline bitfld.long 0x0 14. "CPKN,Clear the PKHA N Size Register" "0: Don't clear the PKHA N Size Register.,1: Clear the PKHA N Size Register." newline bitfld.long 0x0 13. "CPKB,Clear the PKHA B Size Register" "0: Don't clear the PKHA B Size Register.,1: Clear the PKHA B Size Register." newline bitfld.long 0x0 12. "CPKA,Clear the PKHA A Size Register" "0: Don't clear the PKHA A Size Register.,1: Clear the PKHA A Size Register." newline bitfld.long 0x0 6. "C1K,Clear the Class 1 Key Register" "0: Don't clear the Class 1 Key Register.,1: Clear the Class 1 Key Register." newline bitfld.long 0x0 5. "C1C,Clear the Class 1 Context Register" "0: Don't clear the Class 1 Context Register.,1: Clear the Class 1 Context Register." newline bitfld.long 0x0 3. "C1ICV,Clear the Class 1 ICV Size Register" "0: Don't clear the Class 1 ICV Size Register.,1: Clear the Class 1 ICV Size Register." newline bitfld.long 0x0 2. "C1DS,Clear the Class 1 Data Size Register" "0: Don't clear the Class 1 Data Size Register.,1: Clear the Class 1 Data Size Register." newline bitfld.long 0x0 0. "C1M,Clear the Class 1 Mode Register" "0: Don't clear the Class 1 Mode Register.,1: Clear the Class 1 Mode Register." rgroup.long 0x80048++0x7 line.long 0x0 "C0CSTA_MS,CCB 0 Status and Error Register. most-significant half" hexmask.long.byte 0x0 28.--31. 1. "CL2,Class 2 Algorithms" newline hexmask.long.byte 0x0 16.--19. 1. "ERRID2,Error ID 2" newline hexmask.long.byte 0x0 12.--15. 1. "CL1,Class 1 algorithms" newline hexmask.long.byte 0x0 0.--3. 1. "ERRID1,Error ID 1" line.long 0x4 "C0CSTA_LS,CCB 0 Status and Error Register. least-significant half" bitfld.long 0x4 30. "PIZ,Public Key Operation is Zero" "0: The result of a Public Key operation is not zero.,1: The result of a Public Key operation is zero." newline bitfld.long 0x4 29. "GCD,GCD is One" "0: The greatest common divisor of two numbers is..,1: The greatest common divisor of two numbers is one." newline bitfld.long 0x4 28. "PRM,Public Key is Prime" "0: The given number is NOT prime.,1: The given number is probably prime." newline bitfld.long 0x4 21. "SEI,Class 2 Error Interrupt. The Class 2 Error Interrupt has been asserted." "0: No Error,1: Error Interrupt" newline bitfld.long 0x4 20. "PEI,Class 1 Error Interrupt. The Class 1 Error Interrupt has been asserted." "0: No Error,1: Error Interrupt" newline bitfld.long 0x4 17. "SDI,Class 2 Done Interrupt. The Class 2 Done Interrupt has been asserted." "0: Not Done,1: Done Interrupt" newline bitfld.long 0x4 16. "PDI,Class 1 Done Interrupt. The Class 1 Done Interrupt has been asserted." "0: Not Done,1: Done Interrupt" newline bitfld.long 0x4 9. "RNB,RNG Block Busy" "0: RNG Idle,1: RNG Busy" newline bitfld.long 0x4 8. "CB,CRC Block Busy" "0: CRCA Idle,1: CRCA Busy" newline bitfld.long 0x4 7. "MB,MDHA Busy" "0: MDHA Idle,1: MDHA Busy" newline bitfld.long 0x4 6. "PB,PKHA Busy" "0: PKHA Idle,1: PKHA Busy" newline bitfld.long 0x4 2. "DB,DESA Busy" "0: DESA Idle,1: DESA Busy" newline bitfld.long 0x4 1. "AB,AESA Busy" "0: AESA Idle,1: AESA Busy" group.long 0x8005C++0x3 line.long 0x0 "C0C1AADSZR,CCB 0 Class 1 AAD Size Register" hexmask.long.byte 0x0 0.--3. 1. "AASZ,AAD size in Bytes mod 16." group.long 0x80064++0x3 line.long 0x0 "C0C1IVSZR,CCB 0 Class 1 IV Size Register" hexmask.long.byte 0x0 0.--3. 1. "IVSZ,IV size in bytes mod 16." group.long 0x80084++0x3 line.long 0x0 "C0PKASZR,PKHA A Size Register" hexmask.long.word 0x0 0.--9. 1. "PKASZ,PKHA A Memory key size in bytes." group.long 0x8008C++0x3 line.long 0x0 "C0PKBSZR,PKHA B Size Register" hexmask.long.word 0x0 0.--9. 1. "PKBSZ,PKHA B Memory key size in bytes." group.long 0x80094++0x3 line.long 0x0 "C0PKNSZR,PKHA N Size Register" hexmask.long.word 0x0 0.--9. 1. "PKNSZ,PKHA N Memory key size in bytes." group.long 0x8009C++0x3 line.long 0x0 "C0PKESZR,PKHA E Size Register" hexmask.long.word 0x0 0.--9. 1. "PKESZ,PKHA E Memory key size in bytes." group.long 0x80100++0x3F line.long 0x0 "C0C1CTXR0,CCB 0 Class 1 Context Register Word 0" hexmask.long 0x0 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x4 "C0C1CTXR1,CCB 0 Class 1 Context Register Word 1" hexmask.long 0x4 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x8 "C0C1CTXR2,CCB 0 Class 1 Context Register Word 2" hexmask.long 0x8 0.--31. 1. "C1CTX,Class 1 Context." line.long 0xC "C0C1CTXR3,CCB 0 Class 1 Context Register Word 3" hexmask.long 0xC 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x10 "C0C1CTXR4,CCB 0 Class 1 Context Register Word 4" hexmask.long 0x10 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x14 "C0C1CTXR5,CCB 0 Class 1 Context Register Word 5" hexmask.long 0x14 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x18 "C0C1CTXR6,CCB 0 Class 1 Context Register Word 6" hexmask.long 0x18 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x1C "C0C1CTXR7,CCB 0 Class 1 Context Register Word 7" hexmask.long 0x1C 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x20 "C0C1CTXR8,CCB 0 Class 1 Context Register Word 8" hexmask.long 0x20 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x24 "C0C1CTXR9,CCB 0 Class 1 Context Register Word 9" hexmask.long 0x24 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x28 "C0C1CTXR10,CCB 0 Class 1 Context Register Word 10" hexmask.long 0x28 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x2C "C0C1CTXR11,CCB 0 Class 1 Context Register Word 11" hexmask.long 0x2C 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x30 "C0C1CTXR12,CCB 0 Class 1 Context Register Word 12" hexmask.long 0x30 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x34 "C0C1CTXR13,CCB 0 Class 1 Context Register Word 13" hexmask.long 0x34 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x38 "C0C1CTXR14,CCB 0 Class 1 Context Register Word 14" hexmask.long 0x38 0.--31. 1. "C1CTX,Class 1 Context." line.long 0x3C "C0C1CTXR15,CCB 0 Class 1 Context Register Word 15" hexmask.long 0x3C 0.--31. 1. "C1CTX,Class 1 Context." group.long 0x80200++0x1F line.long 0x0 "C0C1KR0,CCB 0 Class 1 Key Registers Word 0" hexmask.long 0x0 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x4 "C0C1KR1,CCB 0 Class 1 Key Registers Word 1" hexmask.long 0x4 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x8 "C0C1KR2,CCB 0 Class 1 Key Registers Word 2" hexmask.long 0x8 0.--31. 1. "C1KEY,Class 1 Key." line.long 0xC "C0C1KR3,CCB 0 Class 1 Key Registers Word 3" hexmask.long 0xC 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x10 "C0C1KR4,CCB 0 Class 1 Key Registers Word 4" hexmask.long 0x10 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x14 "C0C1KR5,CCB 0 Class 1 Key Registers Word 5" hexmask.long 0x14 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x18 "C0C1KR6,CCB 0 Class 1 Key Registers Word 6" hexmask.long 0x18 0.--31. 1. "C1KEY,Class 1 Key." line.long 0x1C "C0C1KR7,CCB 0 Class 1 Key Registers Word 7" hexmask.long 0x1C 0.--31. 1. "C1KEY,Class 1 Key." group.long 0x80404++0x3 line.long 0x0 "C0C2MR,CCB 0 Class 2 Mode Register" hexmask.long.byte 0x0 16.--23. 1. "ALG,Algorithm. This field specifies which algorithm has been requested for an OPERATION command." newline hexmask.long.word 0x0 4.--12. 1. "AAI,Additional Algorithm information" newline bitfld.long 0x0 2.--3. "AS,Algorithm State" "0: Update.,1: Initialize.,2: Finalize.,3: Initialize/Finalize." newline bitfld.long 0x0 1. "ICV,ICV Checking" "0: Don't compare the calculated ICV against a..,1: Compare the calculated ICV against a received ICV." newline bitfld.long 0x0 0. "AP,Authenticate / Protect" "0: Authenticate,1: Protect" group.long 0x8040C++0x3 line.long 0x0 "C0C2KSR,CCB 0 Class 2 Key Size Register" hexmask.long.byte 0x0 0.--7. 1. "C2KS,Class 2 key size in bytes." group.quad 0x80410++0x7 line.quad 0x0 "C0C2DSR,CCB 0 Class 2 Data Size Register" rbitfld.quad 0x0 61.--63. "NUMBITS,Class 2 Data Size Number of bits" "0,1,2,3,4,5,6,7" newline rbitfld.quad 0x0 32. "C2CY,Class 2 Data Size Carry" "0: A write to the Class 2 Data Size Register did..,1: A write to the Class 2 Data Size Register caused.." newline hexmask.quad.long 0x0 0.--31. 1. "C2DS,Class 2 Data Size in Bytes" group.long 0x8041C++0x3 line.long 0x0 "C0C2ICVSZR,CCB 0 Class 2 ICV Size Register" hexmask.long.byte 0x0 0.--3. 1. "ICVSZ,Class 2 ICV size (mod 8) in bytes" group.long 0x80500++0x47 line.long 0x0 "C0C2CTXR0,CCB 0 Class 2 Context Register Word 0" hexmask.long 0x0 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x4 "C0C2CTXR1,CCB 0 Class 2 Context Register Word 1" hexmask.long 0x4 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x8 "C0C2CTXR2,CCB 0 Class 2 Context Register Word 2" hexmask.long 0x8 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0xC "C0C2CTXR3,CCB 0 Class 2 Context Register Word 3" hexmask.long 0xC 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x10 "C0C2CTXR4,CCB 0 Class 2 Context Register Word 4" hexmask.long 0x10 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x14 "C0C2CTXR5,CCB 0 Class 2 Context Register Word 5" hexmask.long 0x14 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x18 "C0C2CTXR6,CCB 0 Class 2 Context Register Word 6" hexmask.long 0x18 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x1C "C0C2CTXR7,CCB 0 Class 2 Context Register Word 7" hexmask.long 0x1C 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x20 "C0C2CTXR8,CCB 0 Class 2 Context Register Word 8" hexmask.long 0x20 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x24 "C0C2CTXR9,CCB 0 Class 2 Context Register Word 9" hexmask.long 0x24 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x28 "C0C2CTXR10,CCB 0 Class 2 Context Register Word 10" hexmask.long 0x28 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x2C "C0C2CTXR11,CCB 0 Class 2 Context Register Word 11" hexmask.long 0x2C 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x30 "C0C2CTXR12,CCB 0 Class 2 Context Register Word 12" hexmask.long 0x30 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x34 "C0C2CTXR13,CCB 0 Class 2 Context Register Word 13" hexmask.long 0x34 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x38 "C0C2CTXR14,CCB 0 Class 2 Context Register Word 14" hexmask.long 0x38 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x3C "C0C2CTXR15,CCB 0 Class 2 Context Register Word 15" hexmask.long 0x3C 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x40 "C0C2CTXR16,CCB 0 Class 2 Context Register Word 16" hexmask.long 0x40 0.--31. 1. "C2CTXR,Class 2 Context." line.long 0x44 "C0C2CTXR17,CCB 0 Class 2 Context Register Word 17" hexmask.long 0x44 0.--31. 1. "C2CTXR,Class 2 Context." group.long 0x80600++0x7F line.long 0x0 "C0C2KEYR0,CCB 0 Class 2 Key Register Word 0" hexmask.long 0x0 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x4 "C0C2KEYR1,CCB 0 Class 2 Key Register Word 1" hexmask.long 0x4 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x8 "C0C2KEYR2,CCB 0 Class 2 Key Register Word 2" hexmask.long 0x8 0.--31. 1. "C2KEY,Class 2 Key." line.long 0xC "C0C2KEYR3,CCB 0 Class 2 Key Register Word 3" hexmask.long 0xC 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x10 "C0C2KEYR4,CCB 0 Class 2 Key Register Word 4" hexmask.long 0x10 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x14 "C0C2KEYR5,CCB 0 Class 2 Key Register Word 5" hexmask.long 0x14 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x18 "C0C2KEYR6,CCB 0 Class 2 Key Register Word 6" hexmask.long 0x18 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x1C "C0C2KEYR7,CCB 0 Class 2 Key Register Word 7" hexmask.long 0x1C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x20 "C0C2KEYR8,CCB 0 Class 2 Key Register Word 8" hexmask.long 0x20 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x24 "C0C2KEYR9,CCB 0 Class 2 Key Register Word 9" hexmask.long 0x24 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x28 "C0C2KEYR10,CCB 0 Class 2 Key Register Word 10" hexmask.long 0x28 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x2C "C0C2KEYR11,CCB 0 Class 2 Key Register Word 11" hexmask.long 0x2C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x30 "C0C2KEYR12,CCB 0 Class 2 Key Register Word 12" hexmask.long 0x30 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x34 "C0C2KEYR13,CCB 0 Class 2 Key Register Word 13" hexmask.long 0x34 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x38 "C0C2KEYR14,CCB 0 Class 2 Key Register Word 14" hexmask.long 0x38 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x3C "C0C2KEYR15,CCB 0 Class 2 Key Register Word 15" hexmask.long 0x3C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x40 "C0C2KEYR16,CCB 0 Class 2 Key Register Word 16" hexmask.long 0x40 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x44 "C0C2KEYR17,CCB 0 Class 2 Key Register Word 17" hexmask.long 0x44 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x48 "C0C2KEYR18,CCB 0 Class 2 Key Register Word 18" hexmask.long 0x48 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x4C "C0C2KEYR19,CCB 0 Class 2 Key Register Word 19" hexmask.long 0x4C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x50 "C0C2KEYR20,CCB 0 Class 2 Key Register Word 20" hexmask.long 0x50 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x54 "C0C2KEYR21,CCB 0 Class 2 Key Register Word 21" hexmask.long 0x54 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x58 "C0C2KEYR22,CCB 0 Class 2 Key Register Word 22" hexmask.long 0x58 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x5C "C0C2KEYR23,CCB 0 Class 2 Key Register Word 23" hexmask.long 0x5C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x60 "C0C2KEYR24,CCB 0 Class 2 Key Register Word 24" hexmask.long 0x60 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x64 "C0C2KEYR25,CCB 0 Class 2 Key Register Word 25" hexmask.long 0x64 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x68 "C0C2KEYR26,CCB 0 Class 2 Key Register Word 26" hexmask.long 0x68 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x6C "C0C2KEYR27,CCB 0 Class 2 Key Register Word 27" hexmask.long 0x6C 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x70 "C0C2KEYR28,CCB 0 Class 2 Key Register Word 28" hexmask.long 0x70 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x74 "C0C2KEYR29,CCB 0 Class 2 Key Register Word 29" hexmask.long 0x74 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x78 "C0C2KEYR30,CCB 0 Class 2 Key Register Word 30" hexmask.long 0x78 0.--31. 1. "C2KEY,Class 2 Key." line.long 0x7C "C0C2KEYR31,CCB 0 Class 2 Key Register Word 31" hexmask.long 0x7C 0.--31. 1. "C2KEY,Class 2 Key." rgroup.long 0x807C0++0x3 line.long 0x0 "C0FIFOSTA,CCB 0 FIFO Status Register" hexmask.long.byte 0x0 24.--31. 1. "C1IQHEAD,This is the current head of the Class 1 Alignment Block queue located within the Input Data FIFO" newline hexmask.long.byte 0x0 16.--23. 1. "C2IQHEAD,This is the current head of the Class 2 Alignment Block queue located within the Input Data FIFO" newline hexmask.long.byte 0x0 8.--15. 1. "DMAOQHEAD,This is the current head of the DMA queue located within the Output Data FIFO" newline hexmask.long.byte 0x0 0.--7. 1. "DECOOQHEAD,This is the current head of the DECO Alignment Block queue located within the Output Data FIFO" wgroup.long 0x807D0++0x3 line.long 0x0 "C0NFIFO,CCB 0 iNformation FIFO When STYPE != 10b" bitfld.long 0x0 30.--31. "DEST,Destination" "0: DECO Alignment Block. If DTYPE == Eh data sent..,1: Class 1.,2: Class 2.,3: Both Class 1 and Class 2." newline bitfld.long 0x0 29. "LC2,Last Class 2" "0: This is not the last Class 2 data.,1: This is the last Class 2 data." newline bitfld.long 0x0 28. "LC1,Last Class 1" "0: This is not the last Class 1 data.,1: This is the last Class 1 data." newline bitfld.long 0x0 27. "FC2,Flush Class 2" "0: Don't flush Class 2 data.,1: Flush Class 2 data." newline bitfld.long 0x0 26. "FC1,Flush Class 1. Flush the remainder of the data out of the Class 1 alignment block." "0: Don't flush Class 1 data.,1: Flush Class 1 data." newline bitfld.long 0x0 24.--25. "STYPE,Source Type" "0,1,2,3" newline hexmask.long.byte 0x0 20.--23. 1. "DTYPE,Data Type" newline bitfld.long 0x0 19. "BND,Boundary padding" "0: Don't pad.,1: Pad to the next 16-byte boundary." newline bitfld.long 0x0 16.--18. "PTYPE,Pad Type" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 15. "OC,OFIFO Continuation - This bit causes the final word to not be popped from the Output Data FIFO." "0: Allow the final word to be popped from the..,1: Don't pop the final word from the Output Data.." newline bitfld.long 0x0 14. "AST,Additional Source Types" "0,1" newline hexmask.long.word 0x0 0.--11. 1. "DL,Data Length" wgroup.long 0x807D0++0x3 line.long 0x0 "C0NFIFO_2,CCB 0 iNformation FIFO When STYPE == 10b" bitfld.long 0x0 30.--31. "DEST,Destination" "0: DECO Alignment Block. If DTYPE is Eh data sent..,1: Class 1.,2: Class 2.,3: Both Class 1 and Class 2." newline bitfld.long 0x0 29. "LC2,Last Class 2" "0: This is not the last Class 2 data.,1: This is the last Class 2 data." newline bitfld.long 0x0 28. "LC1,Last Class 1" "0: This is not the last Class 1 data.,1: This is the last Class 1 data." newline bitfld.long 0x0 27. "FC2,Flush Class 2" "0: Don't flush the Class 2 data.,1: Flush the Class 2 data." newline bitfld.long 0x0 26. "FC1,Flush Class 1. Flush the remainder of the data out of the Class 1 alignment block." "0: Don't flush the Class 1 data.,1: Flush the Class 1 data." newline bitfld.long 0x0 24.--25. "STYPE,Source Type" "0,1,2,3" newline hexmask.long.byte 0x0 20.--23. 1. "DTYPE,Data Type" newline bitfld.long 0x0 19. "BND,Boundary padding" "0: Don't add boundary padding.,1: Add boundary padding." newline bitfld.long 0x0 16.--18. "PTYPE,Pad Type" "0: All Zero.,1: Random with nonzero bytes.,2: Incremented (starting with 01h) followed by a..,3: Random.,4: All Zero with last byte containing the number of..,5: Random with nonzero bytes with last byte 0.,6: N bytes of padding all containing the value N-1.,7: Random with nonzero bytes with the last byte.." newline bitfld.long 0x0 15. "PR,Prediction Resistance - If PTYPE specifies random data setting PR=1 causes the RNG to supply random data for prediction resistance (i" "0: No prediction resistance.,1: Prediction resistance." newline bitfld.long 0x0 11. "BM,Boundary Minus 1" "0: When padding pad to power-of-2 boundary.,1: When padding pad to power-of-2 boundary minus 1.." newline bitfld.long 0x0 10. "PS,Pad Snoop" "0: C2 CHA snoops pad data from padding block.,1: C2 CHA snoops pad data from OFIFO." newline hexmask.long.byte 0x0 0.--6. 1. "PL,Pad Length" wgroup.long 0x807E0++0x3 line.long 0x0 "C0IFIFO,CCB 0 Input Data FIFO" hexmask.long 0x0 0.--31. 1. "IFIFO,Input Data FIFO." rgroup.quad 0x807F0++0x7 line.quad 0x0 "C0OFIFO,CCB 0 Output Data FIFO" hexmask.quad 0x0 0.--63. 1. "OFIFO,Output FIFO" group.long 0x80800++0x3 line.long 0x0 "D0JQCR_MS,DECO0 Job Queue Control Register. most-significant half" bitfld.long 0x0 31. "STEP,Step" "0: DECO has not been told to execute the next..,1: DECO has been told to execute the next command.." newline bitfld.long 0x0 30. "SING,Single Step Mode" "0: Do not tell DECO to execute the descriptor in..,1: Tell DECO to execute the descriptor in.." newline bitfld.long 0x0 29. "WHL,Whole Descriptor" "0: DECO has not been given the whole descriptor.,1: DECO has been given the whole descriptor." newline bitfld.long 0x0 28. "FOUR,Four Words. job queue controller is passing at least 4 words of the Descriptor to DECO." "0: DECO has not been given at least four words of..,1: DECO has been given at least four words of the.." newline bitfld.long 0x0 27. "ILE,Immediate Little Endian" "0: No byte-swapping is performed for immediate data..,1: Byte-swapping is performed for immediate data.." newline bitfld.long 0x0 24.--26. "SHR_FROM,Share From" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 19. "DWS,Double word swap. Causes/allows dword swapping of addresses and MOVE and MATH immediate values." "0: Double Word Swap is NOT set.,1: Double Word Swap is set." newline bitfld.long 0x0 16. "SOB,Shared Descriptor burst" "0: Shared Descriptor has NOT been loaded.,1: Shared Descriptor HAS been loaded." newline rbitfld.long 0x0 15. "AMTD,Allow Make Trusted Descriptor" "0: The Allowed Make Trusted Descriptor bit was NOT..,1: The Allowed Make Trusted Descriptor bit was set." newline rbitfld.long 0x0 8.--10. "SRC,Job Source" "0: Job Ring 0,1: Job Ring 1,2: Job Ring 2,3: Job Ring 3,4: RTIC,?,?,?" newline bitfld.long 0x0 0.--2. "ID,Job ID" "0,1,2,3,4,5,6,7" rgroup.long 0x80804++0x3 line.long 0x0 "D0JQCR_LS,DECO0 Job Queue Control Register. least-significant half" hexmask.long 0x0 0.--31. 1. "CMD,Command" rgroup.quad 0x80808++0x7 line.quad 0x0 "D0DAR,DECO0 Descriptor Address Register" hexmask.quad 0x0 0.--35. 1. "DPTR,Descriptor Pointer. Memory address of the Descriptor. Needed for write-back purposes." rgroup.long 0x80810++0x7 line.long 0x0 "D0OPSTA_MS,DECO0 Operation Status Register. most-significant half" hexmask.long.byte 0x0 28.--31. 1. "STATUS_TYPE,Status Type" newline bitfld.long 0x0 27. "NLJ,Non-Local Jump" "0: The original job descriptor running in this DECO..,1: The original job descriptor running in this DECO.." newline hexmask.long.byte 0x0 8.--14. 1. "COMMAND_INDEX,Command index: A pointer to a 32-bit word within the descriptor" newline hexmask.long.byte 0x0 0.--7. 1. "STATUS,If ERRTYP indicates no error this field contains PKHA/Math Status as defined below" line.long 0x4 "D0OPSTA_LS,DECO0 Operation Status Register. least-significant half" hexmask.long 0x4 0.--31. 1. "OUT_CT,Output Count. Number of bytes written to sequential out pointer." rgroup.long 0x80820++0x7 line.long 0x0 "D0PDIDSR,DECO0 Primary DID Status Register" hexmask.long.word 0x0 19.--29. 1. "PRIM_ICID,DECO Primary ICID" newline hexmask.long.byte 0x0 0.--3. 1. "PRIM_DID,DECO Primary DID" line.long 0x4 "D0ODIDSR,DECO0 Output DID Status Register" hexmask.long.word 0x4 19.--29. 1. "OUT_ICID,DECO Output ICID" newline hexmask.long.byte 0x4 0.--3. 1. "OUT_DID,DECO Output DID" group.long 0x80840++0x1F line.long 0x0 "D0MTH0_MS,DECO0 Math Register 0_MS" hexmask.long 0x0 0.--31. 1. "MATH_MS,MATH register most-significant 32 bits." line.long 0x4 "D0MTH0_LS,DECO0 Math Register 0_LS" hexmask.long 0x4 0.--31. 1. "MATH_LS,MATH register least-significant 32 bits." line.long 0x8 "D0MTH1_MS,DECO0 Math Register 1_MS" hexmask.long 0x8 0.--31. 1. "MATH_MS,MATH register most-significant 32 bits." line.long 0xC "D0MTH1_LS,DECO0 Math Register 1_LS" hexmask.long 0xC 0.--31. 1. "MATH_LS,MATH register least-significant 32 bits." line.long 0x10 "D0MTH2_MS,DECO0 Math Register 2_MS" hexmask.long 0x10 0.--31. 1. "MATH_MS,MATH register most-significant 32 bits." line.long 0x14 "D0MTH2_LS,DECO0 Math Register 2_LS" hexmask.long 0x14 0.--31. 1. "MATH_LS,MATH register least-significant 32 bits." line.long 0x18 "D0MTH3_MS,DECO0 Math Register 3_MS" hexmask.long 0x18 0.--31. 1. "MATH_MS,MATH register most-significant 32 bits." line.long 0x1C "D0MTH3_LS,DECO0 Math Register 3_LS" hexmask.long 0x1C 0.--31. 1. "MATH_LS,MATH register least-significant 32 bits." group.long 0x80880++0xF line.long 0x0 "D0GTR0_0,DECO0 Gather Table Register 0 Word 0" hexmask.long.byte 0x0 0.--3. 1. "ADDRESS_POINTER,most-significant bits of memory address pointed to by table entry" line.long 0x4 "D0GTR0_1,DECO0 Gather Table Register 0 Word 1" hexmask.long 0x4 0.--31. 1. "ADDRESS_POINTER,This field holds the least-significant 32 bits of the memory address to which this table entry points" line.long 0x8 "D0GTR0_2,DECO0 Gather Table Register 0 Word 2" bitfld.long 0x8 31. "E,Extension bit" "0: Address Pointer points to a memory buffer.,1: Address Pointer points to a Scatter/Gather Table.." newline bitfld.long 0x8 30. "F,Final Bit. If set this is the last entry of this Scatter/Gather Table." "0: This is not the last entry of the SGT.,1: This is the last entry of the SGT." newline hexmask.long 0x8 0.--29. 1. "Length,This field specifies how many bytes of data (for Gather Tables) or available space (for Scatter Tables) are located at the address pointed to by the Address Pointer" line.long 0xC "D0GTR0_3,DECO0 Gather Table Register 0 Word 3" hexmask.long.word 0xC 0.--12. 1. "Offset,Offset (measured in bytes) into memory where significant data is to be found" group.long 0x80900++0xF line.long 0x0 "D0STR0_0,DECO0 Scatter Table Register 0 Word 0" hexmask.long.byte 0x0 0.--3. 1. "ADDRESS_POINTER,most-significant bits of memory address pointed to by table entry" line.long 0x4 "D0STR0_1,DECO0 Scatter Table Register 0 Word 1" hexmask.long 0x4 0.--31. 1. "ADDRESS_POINTER,This field holds the least-significant 32 bits of the memory address to which this table entry points" line.long 0x8 "D0STR0_2,DECO0 Scatter Table Register 0 Word 2" bitfld.long 0x8 31. "E,Extension bit" "0: Address Pointer points to a memory buffer.,1: Address Pointer points to a Scatter/Gather Table.." newline bitfld.long 0x8 30. "F,Final Bit. If set this is the last entry of this Scatter/Gather Table." "0: This is not the last entry of the SGT.,1: This is the last entry of the SGT." newline hexmask.long 0x8 0.--29. 1. "Length,This field specifies how many bytes of data (for Gather Tables) or available space (for Scatter Tables) are located at the address pointed to by the Address Pointer" line.long 0xC "D0STR0_3,DECO0 Scatter Table Register 0 Word 3" hexmask.long.word 0xC 0.--12. 1. "Offset,Offset (measured in bytes) into memory where significant data is to be found" group.long 0x80A00++0xFF line.long 0x0 "D0DESB0,DECO0 Descriptor Buffer Word 0" hexmask.long 0x0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x4 "D0DESB1,DECO0 Descriptor Buffer Word 1" hexmask.long 0x4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x8 "D0DESB2,DECO0 Descriptor Buffer Word 2" hexmask.long 0x8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xC "D0DESB3,DECO0 Descriptor Buffer Word 3" hexmask.long 0xC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x10 "D0DESB4,DECO0 Descriptor Buffer Word 4" hexmask.long 0x10 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x14 "D0DESB5,DECO0 Descriptor Buffer Word 5" hexmask.long 0x14 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x18 "D0DESB6,DECO0 Descriptor Buffer Word 6" hexmask.long 0x18 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x1C "D0DESB7,DECO0 Descriptor Buffer Word 7" hexmask.long 0x1C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x20 "D0DESB8,DECO0 Descriptor Buffer Word 8" hexmask.long 0x20 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x24 "D0DESB9,DECO0 Descriptor Buffer Word 9" hexmask.long 0x24 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x28 "D0DESB10,DECO0 Descriptor Buffer Word 10" hexmask.long 0x28 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x2C "D0DESB11,DECO0 Descriptor Buffer Word 11" hexmask.long 0x2C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x30 "D0DESB12,DECO0 Descriptor Buffer Word 12" hexmask.long 0x30 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x34 "D0DESB13,DECO0 Descriptor Buffer Word 13" hexmask.long 0x34 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x38 "D0DESB14,DECO0 Descriptor Buffer Word 14" hexmask.long 0x38 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x3C "D0DESB15,DECO0 Descriptor Buffer Word 15" hexmask.long 0x3C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x40 "D0DESB16,DECO0 Descriptor Buffer Word 16" hexmask.long 0x40 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x44 "D0DESB17,DECO0 Descriptor Buffer Word 17" hexmask.long 0x44 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x48 "D0DESB18,DECO0 Descriptor Buffer Word 18" hexmask.long 0x48 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x4C "D0DESB19,DECO0 Descriptor Buffer Word 19" hexmask.long 0x4C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x50 "D0DESB20,DECO0 Descriptor Buffer Word 20" hexmask.long 0x50 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x54 "D0DESB21,DECO0 Descriptor Buffer Word 21" hexmask.long 0x54 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x58 "D0DESB22,DECO0 Descriptor Buffer Word 22" hexmask.long 0x58 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x5C "D0DESB23,DECO0 Descriptor Buffer Word 23" hexmask.long 0x5C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x60 "D0DESB24,DECO0 Descriptor Buffer Word 24" hexmask.long 0x60 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x64 "D0DESB25,DECO0 Descriptor Buffer Word 25" hexmask.long 0x64 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x68 "D0DESB26,DECO0 Descriptor Buffer Word 26" hexmask.long 0x68 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x6C "D0DESB27,DECO0 Descriptor Buffer Word 27" hexmask.long 0x6C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x70 "D0DESB28,DECO0 Descriptor Buffer Word 28" hexmask.long 0x70 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x74 "D0DESB29,DECO0 Descriptor Buffer Word 29" hexmask.long 0x74 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x78 "D0DESB30,DECO0 Descriptor Buffer Word 30" hexmask.long 0x78 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x7C "D0DESB31,DECO0 Descriptor Buffer Word 31" hexmask.long 0x7C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x80 "D0DESB32,DECO0 Descriptor Buffer Word 32" hexmask.long 0x80 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x84 "D0DESB33,DECO0 Descriptor Buffer Word 33" hexmask.long 0x84 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x88 "D0DESB34,DECO0 Descriptor Buffer Word 34" hexmask.long 0x88 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x8C "D0DESB35,DECO0 Descriptor Buffer Word 35" hexmask.long 0x8C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x90 "D0DESB36,DECO0 Descriptor Buffer Word 36" hexmask.long 0x90 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x94 "D0DESB37,DECO0 Descriptor Buffer Word 37" hexmask.long 0x94 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x98 "D0DESB38,DECO0 Descriptor Buffer Word 38" hexmask.long 0x98 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0x9C "D0DESB39,DECO0 Descriptor Buffer Word 39" hexmask.long 0x9C 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xA0 "D0DESB40,DECO0 Descriptor Buffer Word 40" hexmask.long 0xA0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xA4 "D0DESB41,DECO0 Descriptor Buffer Word 41" hexmask.long 0xA4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xA8 "D0DESB42,DECO0 Descriptor Buffer Word 42" hexmask.long 0xA8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xAC "D0DESB43,DECO0 Descriptor Buffer Word 43" hexmask.long 0xAC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xB0 "D0DESB44,DECO0 Descriptor Buffer Word 44" hexmask.long 0xB0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xB4 "D0DESB45,DECO0 Descriptor Buffer Word 45" hexmask.long 0xB4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xB8 "D0DESB46,DECO0 Descriptor Buffer Word 46" hexmask.long 0xB8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xBC "D0DESB47,DECO0 Descriptor Buffer Word 47" hexmask.long 0xBC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xC0 "D0DESB48,DECO0 Descriptor Buffer Word 48" hexmask.long 0xC0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xC4 "D0DESB49,DECO0 Descriptor Buffer Word 49" hexmask.long 0xC4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xC8 "D0DESB50,DECO0 Descriptor Buffer Word 50" hexmask.long 0xC8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xCC "D0DESB51,DECO0 Descriptor Buffer Word 51" hexmask.long 0xCC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xD0 "D0DESB52,DECO0 Descriptor Buffer Word 52" hexmask.long 0xD0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xD4 "D0DESB53,DECO0 Descriptor Buffer Word 53" hexmask.long 0xD4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xD8 "D0DESB54,DECO0 Descriptor Buffer Word 54" hexmask.long 0xD8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xDC "D0DESB55,DECO0 Descriptor Buffer Word 55" hexmask.long 0xDC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xE0 "D0DESB56,DECO0 Descriptor Buffer Word 56" hexmask.long 0xE0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xE4 "D0DESB57,DECO0 Descriptor Buffer Word 57" hexmask.long 0xE4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xE8 "D0DESB58,DECO0 Descriptor Buffer Word 58" hexmask.long 0xE8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xEC "D0DESB59,DECO0 Descriptor Buffer Word 59" hexmask.long 0xEC 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xF0 "D0DESB60,DECO0 Descriptor Buffer Word 60" hexmask.long 0xF0 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xF4 "D0DESB61,DECO0 Descriptor Buffer Word 61" hexmask.long 0xF4 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xF8 "D0DESB62,DECO0 Descriptor Buffer Word 62" hexmask.long 0xF8 0.--31. 1. "DESBW,Descriptor Buffer Word" line.long 0xFC "D0DESB63,DECO0 Descriptor Buffer Word 63" hexmask.long 0xFC 0.--31. 1. "DESBW,Descriptor Buffer Word" rgroup.long 0x80E00++0x7 line.long 0x0 "D0DJR,DECO0 Debug Job Register" bitfld.long 0x0 31. "STEP,Step" "0: DECO has not been told to execute the next..,1: DECO has been told to execute the next command.." newline bitfld.long 0x0 30. "SING,Single Step Mode" "0: DECO has not been told to execute the descriptor..,1: DECO has been told to execute the descriptor in.." newline bitfld.long 0x0 29. "WHL,Whole Descriptor" "0: DECO has not been given the whole descriptor.,1: DECO has been given the whole descriptor." newline bitfld.long 0x0 28. "FOUR,Four Words" "0: DECO has not been given at least four words of..,1: DECO has been given at least four words of the.." newline bitfld.long 0x0 27. "ILE,Immediate Little Endian" "0: No byte-swapping is performed for immediate data..,1: Byte-swapping is performed for immediate data.." newline bitfld.long 0x0 24.--26. "SHR_FROM,Share From" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 19. "DWS,Double Word Swap. Double word swapping was set." "0: Double Word Swap is NOT set.,1: Double Word Swap is set." newline bitfld.long 0x0 16. "GSD,Got Shared Descriptor" "0: Shared Descriptor was NOT obtained from another..,1: Shared Descriptor was obtained from another DECO." newline bitfld.long 0x0 15. "AMTD,Allow Make Trusted Descriptor" "0: The Allowed Make Trusted Descriptor bit was NOT..,1: The Allowed Make Trusted Descriptor bit was set." newline bitfld.long 0x0 14. "JDDS,Job Descriptor DID Select" "0: Non-SEQ DID,1: SEQ DID" newline bitfld.long 0x0 8.--10. "SRC,Job Source" "0: Job Ring 0,1: Job Ring 1,2: Job Ring 2,3: Job Ring 3,4: RTIC,?,?,?" newline bitfld.long 0x0 0.--2. "ID,Job ID" "0,1,2,3,4,5,6,7" line.long 0x4 "D0DDR,DECO0 Debug DECO Register" bitfld.long 0x4 31. "VALID,Valid" "0: No descriptor is currently running in this DECO.,1: There is currently a descriptor running in this.." newline bitfld.long 0x4 30. "SD,Shared Descriptor" "0: This DECO has not received a shared descriptor..,1: This DECO has received a shared descriptor from.." newline bitfld.long 0x4 28.--29. "TRCT,DMA Transaction Count" "0,1,2,3" newline bitfld.long 0x4 26.--27. "SEQLSEL,SEQ DID Select. This indicates which type of DID is being used for SEQ commands:" "?,1: SEQ DID,2: Non-SEQ DID,3: Trusted DID" newline bitfld.long 0x4 24.--25. "NSEQLSEL,Non-SEQ DID Select. This indicates which type of DID is being used for Non-SEQ commands:" "?,1: SEQ DID,2: Non-SEQ DID,3: Trusted DID" newline hexmask.long.byte 0x4 20.--23. 1. "DECO_STATE,DECO State. The current state of DECO's main state machine." newline bitfld.long 0x4 18.--19. "PDB_WB_ST,PDB Writeback State. Lower two bits of the state machine that tracks the state of PDB writebacks." "0,1,2,3" newline bitfld.long 0x4 16.--17. "PDB_STALL,PDB Stall State" "0,1,2,3" newline bitfld.long 0x4 15. "PTCL_RUN,Protocol running. PTCL_RUN=1 indicates that a protocol is running in this DECO." "0: No protocol is running in this DECO.,1: A protocol is running in this DECO." newline bitfld.long 0x4 14. "NLJ,Took Non-local JUMP" "0: The original job descriptor running in this DECO..,1: The original job descriptor running in this DECO.." newline hexmask.long.byte 0x4 8.--13. 1. "CMD_INDEX,Command Index" newline bitfld.long 0x4 5.--7. "CMD_STAGE,Command Stage" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 4. "CSA,Command Stage Aux" "0,1" newline bitfld.long 0x4 3. "NC,No Command" "0: This DECO is currently executing a command.,1: This DECO is not currently executing a command." newline bitfld.long 0x4 2. "BWB,Burster Write Busy" "0: The WRITE machine in the Burster is not busy.,1: The WRITE machine in the Burster is busy." newline bitfld.long 0x4 1. "BRB,Burster Read Busy" "0: The READ machine in the Burster is not busy.,1: The READ machine in the Burster is busy." newline bitfld.long 0x4 0. "CT,Checking Trusted" "0: This DECO is NOTcurrently generating the..,1: This DECO is currently generating the signature.." rgroup.quad 0x80E08++0xF line.quad 0x0 "D0DJP,DECO0 Debug Job Pointer" hexmask.quad 0x0 0.--35. 1. "JDPTR,Job Descriptor Pointer." line.quad 0x8 "D0SDP,DECO0 Debug Shared Pointer" hexmask.quad 0x8 0.--35. 1. "SDPTR,Shared Descriptor Pointer." rgroup.long 0x80E18++0x7 line.long 0x0 "D0DDR_MS,DECO0 Debug DID. most-significant half" hexmask.long.word 0x0 21.--31. 1. "OUT_ICID,Output ICID" newline hexmask.long.byte 0x0 16.--19. 1. "OUT_DID,Output DID" newline hexmask.long.word 0x0 5.--15. 1. "PRIM_ICID,Primary ICID" newline bitfld.long 0x0 4. "PRIM_TZ,Primary TZ" "0: TrustZone NonSecureWorld,1: TrustZone SecureWorld" newline hexmask.long.byte 0x0 0.--3. 1. "PRIM_DID,Primary DID" line.long 0x4 "D0DDR_LS,DECO0 Debug DID. least-significant half" hexmask.long.word 0x4 19.--29. 1. "OUT_ICID,Output ICID" newline hexmask.long.byte 0x4 0.--3. 1. "OUT_DID,DECO Output Domain Identifier" group.long 0x80E20++0x1B line.long 0x0 "SOL0,Sequence Output Length Register" hexmask.long 0x0 0.--31. 1. "SOL,Output Sequence Length" line.long 0x4 "VSOL0,Variable Sequence Output Length Register" hexmask.long 0x4 0.--31. 1. "VSOL,This value is used in variable-length output data sequences" line.long 0x8 "SIL0,Sequence Input Length Register" hexmask.long 0x8 0.--31. 1. "SIL,This value is used in input data sequences" line.long 0xC "VSIL0,Variable Sequence Input Length Register" hexmask.long 0xC 0.--31. 1. "VSIL,This value is used in variable-length input data sequences" line.long 0x10 "D0POVRD,Protocol Override Register" hexmask.long 0x10 0.--31. 1. "DPOVRD,DPOVRD can be used as a general purpose math register." line.long 0x14 "UVSOL0,Variable Sequence Output Length Register; Upper 32 bits" hexmask.long 0x14 0.--31. 1. "UVSOL,This value is used in variable-length output data sequences" line.long 0x18 "UVSIL0,Variable Sequence Input Length Register; Upper 32 bits" hexmask.long 0x18 0.--31. 1. "UVSIL,This value is used in variable-length input data sequences" tree.end tree "CAN" base ad:0x0 tree "CAN1" base ad:0x400C4000 group.long 0x0++0xB line.long 0x0 "MCR,Module Configuration register" bitfld.long 0x0 31. "MDIS,Module Disable" "0: Enable the FlexCAN module.,1: Disable the FlexCAN module." bitfld.long 0x0 30. "FRZ,Freeze Enable" "0: Not enabled to enter Freeze mode.,1: Enabled to enter Freeze mode." newline bitfld.long 0x0 29. "RFEN,Rx FIFO Enable" "0: Rx FIFO not enabled.,1: Rx FIFO enabled." bitfld.long 0x0 28. "HALT,Halt FlexCAN" "0: No Freeze mode request.,1: Enters Freeze mode if the FRZ bit is asserted." newline rbitfld.long 0x0 27. "NOTRDY,FlexCAN Not Ready" "0: FlexCAN module is either in Normal mode..,1: FlexCAN module is either in Disable mode Doze.." bitfld.long 0x0 26. "WAKMSK,Wake Up Interrupt Mask" "0: Wake Up interrupt is disabled.,1: Wake Up interrupt is enabled." newline bitfld.long 0x0 25. "SOFTRST,Soft Reset" "0: No reset request.,1: Resets the registers affected by soft reset." rbitfld.long 0x0 24. "FRZACK,Freeze Mode Acknowledge" "0: FlexCAN not in Freeze mode prescaler running.,1: FlexCAN in Freeze mode prescaler stopped." newline bitfld.long 0x0 23. "SUPV,Supervisor Mode" "0: FlexCAN is in User mode. Affected registers..,1: FlexCAN is in Supervisor mode. Affected.." bitfld.long 0x0 22. "SLFWAK,Self Wake Up" "0: FlexCAN Self Wake Up feature is disabled.,1: FlexCAN Self Wake Up feature is enabled." newline bitfld.long 0x0 21. "WRNEN,Warning Interrupt Enable" "0: TWRNINT and RWRNINT bits are zero independent of..,1: TWRNINT and RWRNINT bits are set when the.." rbitfld.long 0x0 20. "LPMACK,Low-Power Mode Acknowledge" "0: FlexCAN is not in a low-power mode.,1: FlexCAN is in a low-power mode." newline bitfld.long 0x0 19. "WAKSRC,Wake Up Source" "0: FlexCAN uses the unfiltered Rx input to detect..,1: FlexCAN uses the filtered Rx input to detect.." bitfld.long 0x0 18. "DOZE,Doze Mode Enable" "0: FlexCAN is not enabled to enter low-power mode..,1: FlexCAN is enabled to enter low-power mode when.." newline bitfld.long 0x0 17. "SRXDIS,Self Reception Disable" "0: Self-reception enabled.,1: Self-reception disabled." bitfld.long 0x0 16. "IRMQ,Individual Rx Masking And Queue Enable" "0: Individual Rx masking and queue feature are..,1: Individual Rx masking and queue feature are.." newline bitfld.long 0x0 15. "DMA,DMA Enable" "0: DMA feature for RX FIFO disabled.,1: DMA feature for RX FIFO enabled." bitfld.long 0x0 13. "LPRIOEN,Local Priority Enable" "0: Local Priority disabled.,1: Local Priority enabled." newline bitfld.long 0x0 12. "AEN,Abort Enable" "0: Abort disabled.,1: Abort enabled." bitfld.long 0x0 11. "FDEN,CAN FD operation enable" "0: CAN FD is disabled. FlexCAN is able to receive..,1: CAN FD is enabled. FlexCAN is able to receive.." newline bitfld.long 0x0 8.--9. "IDAM,ID Acceptance Mode" "0: Format A: One full ID (standard and extended)..,1: Format B: Two full standard IDs or two partial..,2: Format C: Four partial 8-bit standard IDs per ID..,3: Format D: All frames rejected." hexmask.long.byte 0x0 0.--6. 1. "MAXMB,Number Of The Last Message Buffer" line.long 0x4 "CTRL1,Control 1 register" hexmask.long.byte 0x4 24.--31. 1. "PRESDIV,Prescaler Division Factor" bitfld.long 0x4 22.--23. "RJW,Resync Jump Width" "0,1,2,3" newline bitfld.long 0x4 19.--21. "PSEG1,Phase Segment 1" "0,1,2,3,4,5,6,7" bitfld.long 0x4 16.--18. "PSEG2,Phase Segment 2" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 15. "BOFFMSK,Bus Off Interrupt Mask" "0: Bus Off interrupt disabled.,1: Bus Off interrupt enabled." bitfld.long 0x4 14. "ERRMSK,Error Interrupt Mask" "0: Error interrupt disabled.,1: Error interrupt enabled." newline bitfld.long 0x4 13. "CLKSRC,CAN Engine Clock Source" "0: The CAN engine clock source is the oscillator..,1: The CAN engine clock source is the peripheral.." bitfld.long 0x4 12. "LPB,Loop Back Mode" "0: Loop Back disabled.,1: Loop Back enabled." newline bitfld.long 0x4 11. "TWRNMSK,Tx Warning Interrupt Mask" "0: Tx Warning interrupt disabled.,1: Tx Warning interrupt enabled." bitfld.long 0x4 10. "RWRNMSK,Rx Warning Interrupt Mask" "0: Rx Warning interrupt disabled.,1: Rx Warning interrupt enabled." newline bitfld.long 0x4 7. "SMP,CAN Bit Sampling" "0: Just one sample is used to determine the bit..,1: Three samples are used to determine the value of.." bitfld.long 0x4 6. "BOFFREC,Bus Off Recovery" "0: Automatic recovering from Bus Off state enabled.,1: Automatic recovering from Bus Off state disabled." newline bitfld.long 0x4 5. "TSYN,Timer Sync" "0: Timer sync feature disabled,1: Timer sync feature enabled" bitfld.long 0x4 4. "LBUF,Lowest Buffer Transmitted First" "0: Buffer with highest priority is transmitted first.,1: Lowest number buffer is transmitted first." newline bitfld.long 0x4 3. "LOM,Listen-Only Mode" "0: Listen-Only mode is deactivated.,1: FlexCAN module operates in Listen-Only mode." bitfld.long 0x4 0.--2. "PROPSEG,Propagation Segment" "0,1,2,3,4,5,6,7" line.long 0x8 "TIMER,Free Running Timer" hexmask.long.word 0x8 0.--15. 1. "TIMER,Timer Value" group.long 0x10++0x27 line.long 0x0 "RXMGMASK,Rx Mailboxes Global Mask register" hexmask.long 0x0 0.--31. 1. "MG,Rx Mailboxes Global Mask Bits" line.long 0x4 "RX14MASK,Rx 14 Mask register" hexmask.long 0x4 0.--31. 1. "RX14M,Rx Buffer 14 Mask Bits" line.long 0x8 "RX15MASK,Rx 15 Mask register" hexmask.long 0x8 0.--31. 1. "RX15M,Rx Buffer 15 Mask Bits" line.long 0xC "ECR,Error Counter" hexmask.long.byte 0xC 24.--31. 1. "RXERRCNT_FAST,Receive Error Counter for fast bits" hexmask.long.byte 0xC 16.--23. 1. "TXERRCNT_FAST,Transmit Error Counter for fast bits" newline hexmask.long.byte 0xC 8.--15. 1. "RXERRCNT,Receive Error Counter" hexmask.long.byte 0xC 0.--7. 1. "TXERRCNT,Transmit Error Counter" line.long 0x10 "ESR1,Error and Status 1 register" rbitfld.long 0x10 31. "BIT1ERR_FAST,Bit1 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as recessive is received.." rbitfld.long 0x10 30. "BIT0ERR_FAST,Bit0 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." newline rbitfld.long 0x10 28. "CRCERR_FAST,Cyclic Redundancy Check Error in the CRC field of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 27. "FRMERR_FAST,Form Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A form error occurred since last read of this.." newline rbitfld.long 0x10 26. "STFERR_FAST,Stuffing Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A stuffing error occurred since last read of.." eventfld.long 0x10 21. "ERROVR,Error Overrun" "0: Overrun has not occurred.,1: Overrun has occurred." newline eventfld.long 0x10 20. "ERRINT_FAST,Error interrupt for errors detected in Data Phase of CAN FD frames with BRS bit set" "0: No such occurrence.,1: Indicates setting of any error bit detected in.." eventfld.long 0x10 19. "BOFFDONEINT,Bus Off Done Interrupt" "0: No such occurrence.,1: FlexCAN module has completed Bus Off process." newline rbitfld.long 0x10 18. "SYNCH,CAN Synchronization Status" "0: FlexCAN is not synchronized to the CAN bus.,1: FlexCAN is synchronized to the CAN bus." eventfld.long 0x10 17. "TWRNINT,Tx Warning Interrupt Flag" "0: No such occurrence.,1: The Tx error counter transitioned from less than.." newline eventfld.long 0x10 16. "RWRNINT,Rx Warning Interrupt Flag" "0: No such occurrence.,1: The Rx error counter transitioned from less than.." rbitfld.long 0x10 15. "BIT1ERR,Bit1 Error" "0: No such occurrence.,1: At least one bit sent as recessive is received.." newline rbitfld.long 0x10 14. "BIT0ERR,Bit0 Error" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." rbitfld.long 0x10 13. "ACKERR,Acknowledge Error" "0: No such occurrence.,1: An ACK error occurred since last read of this.." newline rbitfld.long 0x10 12. "CRCERR,Cyclic Redundancy Check Error" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 11. "FRMERR,Form Error" "0: No such occurrence.,1: A Form Error occurred since last read of this.." newline rbitfld.long 0x10 10. "STFERR,Stuffing Error" "0: No such occurrence.,1: A stuffing error occurred since last read of.." rbitfld.long 0x10 9. "TXWRN,TX Error Warning" "0: No such occurrence.,1: TXERRCNT is greater than or equal to 96." newline rbitfld.long 0x10 8. "RXWRN,Rx Error Warning" "0: No such occurrence.,1: RXERRCNT is greater than or equal to 96." rbitfld.long 0x10 7. "IDLE,IDLE" "0: No such occurrence.,1: CAN bus is now IDLE." newline rbitfld.long 0x10 6. "TX,FlexCAN In Transmission" "0: FlexCAN is not transmitting a message.,1: FlexCAN is transmitting a message." rbitfld.long 0x10 4.--5. "FLTCONF,Fault Confinement State" "0: Bus Off,1: Error Passive,2: Bus Off,3: Bus Off" newline rbitfld.long 0x10 3. "RX,FlexCAN In Reception" "0: FlexCAN is not receiving a message.,1: FlexCAN is receiving a message." eventfld.long 0x10 2. "BOFFINT,Bus Off Interrupt" "0: No such occurrence.,1: FlexCAN module entered Bus Off state." newline eventfld.long 0x10 1. "ERRINT,Error Interrupt" "0: No such occurrence.,1: Indicates setting of any error bit in the Error.." eventfld.long 0x10 0. "WAKINT,Wake-Up Interrupt" "0: No such occurrence.,1: Indicates a recessive to dominant transition was.." line.long 0x14 "IMASK2,Interrupt Masks 2 register" hexmask.long 0x14 0.--31. 1. "BUF63TO32M,Buffer MBi Mask" line.long 0x18 "IMASK1,Interrupt Masks 1 register" hexmask.long 0x18 0.--31. 1. "BUF31TO0M,Buffer MBi Mask" line.long 0x1C "IFLAG2,Interrupt Flags 2 register" hexmask.long 0x1C 0.--31. 1. "BUF63TO32I,Buffer MBi Interrupt" line.long 0x20 "IFLAG1,Interrupt Flags 1 register" hexmask.long.tbyte 0x20 8.--31. 1. "BUF31TO8I,Buffer MBi Interrupt" eventfld.long 0x20 7. "BUF7I,Buffer MB7 Interrupt Or Rx FIFO Overflow" "0: No occurrence of MB7 completing..,1: MB7 completed transmission/reception when.." newline eventfld.long 0x20 6. "BUF6I,Buffer MB6 Interrupt Or Rx FIFO Warning" "0: No occurrence of MB6 completing..,1: MB6 completed transmission/reception when.." eventfld.long 0x20 5. "BUF5I,Buffer MB5 Interrupt Or Frames available in Rx FIFO" "0: No occurrence of MB5 completing..,1: MB5 completed transmission/reception when.." newline hexmask.long.byte 0x20 1.--4. 1. "BUF4TO1I,Buffer MBi Interrupt Or Reserved" eventfld.long 0x20 0. "BUF0I,Buffer MB0 Interrupt Or Clear FIFO bit" "0: The corresponding buffer has no occurrence of..,1: The corresponding buffer has successfully.." line.long 0x24 "CTRL2,Control 2 register" bitfld.long 0x24 31. "ERRMSK_FAST,Error Interrupt Mask for errors detected in the data phase of fast CAN FD frames" "0: ERRINT_FAST error interrupt disabled.,1: ERRINT_FAST error interrupt enabled." bitfld.long 0x24 30. "BOFFDONEMSK,Bus Off Done Interrupt Mask" "0: Bus off done interrupt disabled.,1: Bus off done interrupt enabled." newline bitfld.long 0x24 29. "ECRWRE,Error-correction Configuration Register Write Enable" "0: Disable update.,1: Enable update." bitfld.long 0x24 28. "WRMFRZ,Write-Access To Memory In Freeze Mode" "0: Maintain the write access restrictions.,1: Enable unrestricted write access to FlexCAN.." newline hexmask.long.byte 0x24 24.--27. 1. "RFFN,Number Of Rx FIFO Filters" hexmask.long.byte 0x24 19.--23. 1. "TASD,Tx Arbitration Start Delay" newline bitfld.long 0x24 18. "MRP,Mailboxes Reception Priority" "0: Matching starts from Rx FIFO and continues on..,1: Matching starts from mailboxes and continues on.." bitfld.long 0x24 17. "RRS,Remote Request Storing" "0: Remote response frame is generated.,1: Remote request frame is stored." newline bitfld.long 0x24 16. "EACEN,Entire Frame Arbitration Field Comparison Enable For Rx Mailboxes" "0: Rx mailbox filter's IDE bit is always compared..,1: Enables the comparison of both Rx mailbox.." bitfld.long 0x24 15. "TIMER_SRC,Timer Source" "0: The free running timer is clocked by the CAN bit..,1: The free running timer is clocked by an external.." newline bitfld.long 0x24 14. "PREXCEN,Protocol Exception Enable" "0: Protocol exception is disabled.,1: Protocol exception is enabled." bitfld.long 0x24 12. "ISOCANFDEN,ISO CAN FD Enable" "0: FlexCAN operates using the non-ISO CAN FD..,1: FlexCAN operates using the ISO CAN FD protocol.." newline bitfld.long 0x24 11. "EDFLTDIS,Edge Filter Disable" "0: Edge filter is enabled,1: Edge filter is disabled" rgroup.long 0x38++0x3 line.long 0x0 "ESR2,Error and Status 2 register" hexmask.long.byte 0x0 16.--22. 1. "LPTM,Lowest Priority Tx Mailbox" bitfld.long 0x0 14. "VPS,Valid Priority Status" "0: Contents of IMB and LPTM are invalid.,1: Contents of IMB and LPTM are valid." newline bitfld.long 0x0 13. "IMB,Inactive Mailbox" "0: If ESR2[VPS] is asserted the ESR2[LPTM] is not..,1: If ESR2[VPS] is asserted there is at least one.." rgroup.long 0x44++0x3 line.long 0x0 "CRCR,CRC register" hexmask.long.byte 0x0 16.--22. 1. "MBCRC,CRC Mailbox" hexmask.long.word 0x0 0.--14. 1. "TXCRC,Transmitted CRC value" group.long 0x48++0x3 line.long 0x0 "RXFGMASK,Rx FIFO Global Mask register" hexmask.long 0x0 0.--31. 1. "FGM,Rx FIFO Global Mask Bits" rgroup.long 0x4C++0x3 line.long 0x0 "RXFIR,Rx FIFO Information register" hexmask.long.word 0x0 0.--8. 1. "IDHIT,Identifier Acceptance Filter Hit Indicator" group.long 0x50++0x3 line.long 0x0 "CBT,CAN Bit Timing register" bitfld.long 0x0 31. "BTF,Bit Timing Format Enable" "0: Extended bit time definitions disabled.,1: Extended bit time definitions enabled." hexmask.long.word 0x0 21.--30. 1. "EPRESDIV,Extended Prescaler Division Factor" newline hexmask.long.byte 0x0 16.--20. 1. "ERJW,Extended Resync Jump Width" hexmask.long.byte 0x0 10.--15. 1. "EPROPSEG,Extended Propagation Segment" newline hexmask.long.byte 0x0 5.--9. 1. "EPSEG1,Extended Phase Segment 1" hexmask.long.byte 0x0 0.--4. 1. "EPSEG2,Extended Phase Segment 2" group.long 0x80++0x3 line.long 0x0 "CS0,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_16B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_32B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_64B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x7 line.long 0x0 "MB0_8B_CS,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID0,Message Buffer 0 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_16B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_32B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_64B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x7 line.long 0x0 "MB0_8B_ID,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_32B_WORD0_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_64B_WORD0_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_8B_WORD0,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x7 line.long 0x0 "WORD00,Message Buffer 0 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_32B_WORD1_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_64B_WORD1_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_8B_WORD1,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x7 line.long 0x0 "WORD10,Message Buffer 0 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS1,Message Buffer 1 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x90++0x3 line.long 0x0 "MB0_16B_WORD2_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_32B_WORD2_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_64B_WORD2_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x7 line.long 0x0 "MB1_8B_CS,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID1,Message Buffer 1 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x94++0x3 line.long 0x0 "MB0_16B_WORD3_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_32B_WORD3_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_64B_WORD3_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x7 line.long 0x0 "MB1_8B_ID,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB0_64B_WORD4_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB1_16B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x98++0x3 line.long 0x0 "MB1_8B_WORD0,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x98++0x7 line.long 0x0 "WORD01,Message Buffer 1 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB0_64B_WORD5_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB1_16B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x9C++0x3 line.long 0x0 "MB1_8B_WORD1,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x7 line.long 0x0 "WORD11,Message Buffer 1 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS2,Message Buffer 2 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA0++0x3 line.long 0x0 "MB0_32B_WORD6_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB0_64B_WORD6_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB1_16B_WORD0_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x7 line.long 0x0 "MB2_8B_CS,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID2,Message Buffer 2 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xA4++0x3 line.long 0x0 "MB0_32B_WORD7_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB0_64B_WORD7_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB1_16B_WORD1_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x7 line.long 0x0 "MB2_8B_ID,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_16B_WORD2_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_32B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA8++0x3 line.long 0x0 "MB2_8B_WORD0,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x7 line.long 0x0 "WORD02,Message Buffer 2 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_16B_WORD3_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_32B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xAC++0x3 line.long 0x0 "MB2_8B_WORD1,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x7 line.long 0x0 "WORD12,Message Buffer 2 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS3,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x3 line.long 0x0 "MB0_64B_WORD10_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB1_32B_WORD0_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB2_16B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x7 line.long 0x0 "MB3_8B_CS,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID3,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x3 line.long 0x0 "MB0_64B_WORD11_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB1_32B_WORD1_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB2_16B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x7 line.long 0x0 "MB3_8B_ID,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB1_32B_WORD2_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB2_16B_WORD0_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB3_8B_WORD0,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x7 line.long 0x0 "WORD03,Message Buffer 3 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB1_32B_WORD3_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB2_16B_WORD1_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB3_8B_WORD1,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x7 line.long 0x0 "WORD13,Message Buffer 3 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS4,Message Buffer 4 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC0++0x3 line.long 0x0 "MB0_64B_WORD14_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB1_32B_WORD4_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB2_16B_WORD2_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x7 line.long 0x0 "MB4_8B_CS,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID4,Message Buffer 4 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xC4++0x3 line.long 0x0 "MB0_64B_WORD15_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB1_32B_WORD5_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB2_16B_WORD3_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x7 line.long 0x0 "MB4_8B_ID,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x3 line.long 0x0 "MB1_64B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB3_16B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB4_8B_WORD0,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x7 line.long 0x0 "WORD04,Message Buffer 4 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x3 line.long 0x0 "MB1_64B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB3_16B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB4_8B_WORD1,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x7 line.long 0x0 "WORD14,Message Buffer 4 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS5,Message Buffer 5 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB1_64B_WORD0_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x3 line.long 0x0 "MB2_32B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB3_16B_WORD0_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x7 line.long 0x0 "MB5_8B_CS,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID5,Message Buffer 5 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB1_64B_WORD1_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x3 line.long 0x0 "MB2_32B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB3_16B_WORD1_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x7 line.long 0x0 "MB5_8B_ID,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD2_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB2_32B_WORD0_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB3_16B_WORD2_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB5_8B_WORD0,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x7 line.long 0x0 "WORD05,Message Buffer 5 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB2_32B_WORD1_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB3_16B_WORD3_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB5_8B_WORD1,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x7 line.long 0x0 "WORD15,Message Buffer 5 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS6,Message Buffer 6 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x3 line.long 0x0 "MB1_64B_WORD4_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB2_32B_WORD2_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB4_16B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x7 line.long 0x0 "MB6_8B_CS,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID6,Message Buffer 6 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x3 line.long 0x0 "MB1_64B_WORD5_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB2_32B_WORD3_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB4_16B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x7 line.long 0x0 "MB6_8B_ID,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB2_32B_WORD4_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB4_16B_WORD0_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB6_8B_WORD0,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x7 line.long 0x0 "WORD06,Message Buffer 6 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB2_32B_WORD5_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB4_16B_WORD1_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB6_8B_WORD1,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x7 line.long 0x0 "WORD16,Message Buffer 6 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS7,Message Buffer 7 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF0++0x3 line.long 0x0 "MB1_64B_WORD8_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB2_32B_WORD6_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB4_16B_WORD2_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x7 line.long 0x0 "MB7_8B_CS,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID7,Message Buffer 7 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xF4++0x3 line.long 0x0 "MB1_64B_WORD9_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB2_32B_WORD7_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB4_16B_WORD3_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x7 line.long 0x0 "MB7_8B_ID,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD10_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x3 line.long 0x0 "MB3_32B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB5_16B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB7_8B_WORD0,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x7 line.long 0x0 "WORD07,Message Buffer 7 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x3 line.long 0x0 "MB3_32B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB5_16B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB7_8B_WORD1,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x7 line.long 0x0 "WORD17,Message Buffer 7 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS8,Message Buffer 8 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x100++0x3 line.long 0x0 "MB1_64B_WORD12_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB3_32B_WORD0_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB5_16B_WORD0_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x7 line.long 0x0 "MB8_8B_CS,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID8,Message Buffer 8 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x104++0x3 line.long 0x0 "MB1_64B_WORD13_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB3_32B_WORD1_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB5_16B_WORD1_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x7 line.long 0x0 "MB8_8B_ID,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD14_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB3_32B_WORD2_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB5_16B_WORD2_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB8_8B_WORD0,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x108++0x7 line.long 0x0 "WORD08,Message Buffer 8 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB3_32B_WORD3_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB5_16B_WORD3_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB8_8B_WORD1,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x7 line.long 0x0 "WORD18,Message Buffer 8 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS9,Message Buffer 9 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB2_64B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB3_32B_WORD4_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x110++0x3 line.long 0x0 "MB6_16B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x7 line.long 0x0 "MB9_8B_CS,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID9,Message Buffer 9 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB2_64B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB3_32B_WORD5_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x114++0x3 line.long 0x0 "MB6_16B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x7 line.long 0x0 "MB9_8B_ID,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB3_32B_WORD6_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB6_16B_WORD0_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB9_8B_WORD0,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x7 line.long 0x0 "WORD09,Message Buffer 9 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB3_32B_WORD7_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB6_16B_WORD1_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB9_8B_WORD1,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x7 line.long 0x0 "WORD19,Message Buffer 9 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS10,Message Buffer 10 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB10_8B_CS,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB2_64B_WORD2_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x120++0x3 line.long 0x0 "MB4_32B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x7 line.long 0x0 "MB6_16B_WORD2_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID10,Message Buffer 10 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB10_8B_ID,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB2_64B_WORD3_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x124++0x3 line.long 0x0 "MB4_32B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x7 line.long 0x0 "MB6_16B_WORD3_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD0,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB2_64B_WORD4_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB4_32B_WORD0_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB7_16B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x128++0x7 line.long 0x0 "WORD010,Message Buffer 10 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD1,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB2_64B_WORD5_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB4_32B_WORD1_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB7_16B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x12C++0x7 line.long 0x0 "WORD110,Message Buffer 10 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS11,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB11_8B_CS,Message Buffer 11 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB2_64B_WORD6_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x130++0x3 line.long 0x0 "MB4_32B_WORD2_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x130++0x7 line.long 0x0 "MB7_16B_WORD0_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID11,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB11_8B_ID,Message Buffer 11 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB2_64B_WORD7_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x134++0x3 line.long 0x0 "MB4_32B_WORD3_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x134++0x7 line.long 0x0 "MB7_16B_WORD1_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD0,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB2_64B_WORD8_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB4_32B_WORD4_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB7_16B_WORD2_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x138++0x7 line.long 0x0 "WORD011,Message Buffer 11 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD1,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB2_64B_WORD9_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB4_32B_WORD5_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB7_16B_WORD3_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x7 line.long 0x0 "WORD111,Message Buffer 11 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS12,Message Buffer 12 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB12_8B_CS,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB2_64B_WORD10_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x140++0x3 line.long 0x0 "MB4_32B_WORD6_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x140++0x7 line.long 0x0 "MB8_16B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID12,Message Buffer 12 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB12_8B_ID,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB2_64B_WORD11_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x144++0x3 line.long 0x0 "MB4_32B_WORD7_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x144++0x7 line.long 0x0 "MB8_16B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB12_8B_WORD0,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB2_64B_WORD12_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB5_32B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x148++0x3 line.long 0x0 "MB8_16B_WORD0_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x7 line.long 0x0 "WORD012,Message Buffer 12 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_8B_WORD1,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB2_64B_WORD13_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB5_32B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x14C++0x3 line.long 0x0 "MB8_16B_WORD1_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x7 line.long 0x0 "WORD112,Message Buffer 12 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS13,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB13_8B_CS,Message Buffer 13 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB2_64B_WORD14_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x150++0x3 line.long 0x0 "MB5_32B_WORD0_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x150++0x7 line.long 0x0 "MB8_16B_WORD2_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID13,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB13_8B_ID,Message Buffer 13 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB2_64B_WORD15_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x154++0x3 line.long 0x0 "MB5_32B_WORD1_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x154++0x7 line.long 0x0 "MB8_16B_WORD3_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD0,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB3_64B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x3 line.long 0x0 "MB5_32B_WORD2_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB9_16B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x7 line.long 0x0 "WORD013,Message Buffer 13 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD1,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB3_64B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x3 line.long 0x0 "MB5_32B_WORD3_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB9_16B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x7 line.long 0x0 "WORD113,Message Buffer 13 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS14,Message Buffer 14 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB14_8B_CS,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB3_64B_WORD0_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x160++0x3 line.long 0x0 "MB5_32B_WORD4_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x160++0x7 line.long 0x0 "MB9_16B_WORD0_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID14,Message Buffer 14 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB14_8B_ID,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB3_64B_WORD1_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x164++0x3 line.long 0x0 "MB5_32B_WORD5_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x164++0x7 line.long 0x0 "MB9_16B_WORD1_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD0,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB3_64B_WORD2_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB5_32B_WORD6_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB9_16B_WORD2_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x7 line.long 0x0 "WORD014,Message Buffer 14 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD1,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB3_64B_WORD3_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB5_32B_WORD7_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB9_16B_WORD3_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x7 line.long 0x0 "WORD114,Message Buffer 14 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS15,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB10_16B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB15_8B_CS,Message Buffer 15 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB3_64B_WORD4_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x170++0x7 line.long 0x0 "MB6_32B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID15,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB10_16B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB15_8B_ID,Message Buffer 15 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB3_64B_WORD5_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x174++0x7 line.long 0x0 "MB6_32B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB15_8B_WORD0,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB3_64B_WORD6_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB6_32B_WORD0_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x7 line.long 0x0 "WORD015,Message Buffer 15 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB15_8B_WORD1,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB3_64B_WORD7_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB6_32B_WORD1_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x7 line.long 0x0 "WORD115,Message Buffer 15 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS16,Message Buffer 16 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB10_16B_WORD2_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x180++0x3 line.long 0x0 "MB16_8B_CS,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB3_64B_WORD8_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x180++0x7 line.long 0x0 "MB6_32B_WORD2_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID16,Message Buffer 16 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB10_16B_WORD3_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x184++0x3 line.long 0x0 "MB16_8B_ID,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB3_64B_WORD9_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x184++0x7 line.long 0x0 "MB6_32B_WORD3_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x188++0x3 line.long 0x0 "MB16_8B_WORD0,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB3_64B_WORD10_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB6_32B_WORD4_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x188++0x7 line.long 0x0 "WORD016,Message Buffer 16 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x18C++0x3 line.long 0x0 "MB16_8B_WORD1,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB3_64B_WORD11_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB6_32B_WORD5_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x7 line.long 0x0 "WORD116,Message Buffer 16 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS17,Message Buffer 17 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB11_16B_WORD0_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x190++0x3 line.long 0x0 "MB17_8B_CS,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB3_64B_WORD12_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x190++0x7 line.long 0x0 "MB6_32B_WORD6_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID17,Message Buffer 17 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB11_16B_WORD1_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x194++0x3 line.long 0x0 "MB17_8B_ID,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB3_64B_WORD13_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x194++0x7 line.long 0x0 "MB6_32B_WORD7_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB17_8B_WORD0,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB3_64B_WORD14_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB7_32B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x198++0x7 line.long 0x0 "WORD017,Message Buffer 17 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB17_8B_WORD1,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB3_64B_WORD15_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB7_32B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x19C++0x7 line.long 0x0 "WORD117,Message Buffer 17 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS18,Message Buffer 18 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB12_16B_CS_L,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB18_8B_CS,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB4_64B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x7 line.long 0x0 "MB7_32B_WORD0_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID18,Message Buffer 18 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB12_16B_ID_L,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB18_8B_ID,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB4_64B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x7 line.long 0x0 "MB7_32B_WORD1_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB18_8B_WORD0,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB4_64B_WORD0_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB7_32B_WORD2_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x7 line.long 0x0 "WORD018,Message Buffer 18 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB18_8B_WORD1,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB4_64B_WORD1_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB7_32B_WORD3_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x7 line.long 0x0 "WORD118,Message Buffer 18 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS19,Message Buffer 19 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB12_16B_WORD2_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x3 line.long 0x0 "MB19_8B_CS,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB4_64B_WORD2_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x7 line.long 0x0 "MB7_32B_WORD4_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID19,Message Buffer 19 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB12_16B_WORD3_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x3 line.long 0x0 "MB19_8B_ID,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB4_64B_WORD3_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x7 line.long 0x0 "MB7_32B_WORD5_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_L,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B8++0x3 line.long 0x0 "MB19_8B_WORD0,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB4_64B_WORD4_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB7_32B_WORD6_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x7 line.long 0x0 "WORD019,Message Buffer 19 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_L,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1BC++0x3 line.long 0x0 "MB19_8B_WORD1,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB4_64B_WORD5_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB7_32B_WORD7_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x7 line.long 0x0 "WORD119,Message Buffer 19 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS20,Message Buffer 20 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB13_16B_WORD0_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x3 line.long 0x0 "MB20_8B_CS,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB4_64B_WORD6_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x7 line.long 0x0 "MB8_32B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID20,Message Buffer 20 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB13_16B_WORD1_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x3 line.long 0x0 "MB20_8B_ID,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB4_64B_WORD7_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x7 line.long 0x0 "MB8_32B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB20_8B_WORD0,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB4_64B_WORD8_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB8_32B_WORD0_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x7 line.long 0x0 "WORD020,Message Buffer 20 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB20_8B_WORD1,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB4_64B_WORD9_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB8_32B_WORD1_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x7 line.long 0x0 "WORD120,Message Buffer 20 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS21,Message Buffer 21 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB14_16B_CS_L,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB21_8B_CS,Message Buffer 21 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB4_64B_WORD10_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x1D0++0x7 line.long 0x0 "MB8_32B_WORD2_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID21,Message Buffer 21 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB14_16B_ID_L,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB21_8B_ID,Message Buffer 21 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB4_64B_WORD11_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x1D4++0x7 line.long 0x0 "MB8_32B_WORD3_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB21_8B_WORD0,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB4_64B_WORD12_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB8_32B_WORD4_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x7 line.long 0x0 "WORD021,Message Buffer 21 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB21_8B_WORD1,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB4_64B_WORD13_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB8_32B_WORD5_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x7 line.long 0x0 "WORD121,Message Buffer 21 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS22,Message Buffer 22 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB14_16B_WORD2_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x3 line.long 0x0 "MB22_8B_CS,Message Buffer 22 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB4_64B_WORD14_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x7 line.long 0x0 "MB8_32B_WORD6_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID22,Message Buffer 22 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB14_16B_WORD3_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x3 line.long 0x0 "MB22_8B_ID,Message Buffer 22 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB4_64B_WORD15_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x7 line.long 0x0 "MB8_32B_WORD7_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_L,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB22_8B_WORD0,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1E8++0x3 line.long 0x0 "MB5_64B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB9_32B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x7 line.long 0x0 "WORD022,Message Buffer 22 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_L,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB22_8B_WORD1,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1EC++0x3 line.long 0x0 "MB5_64B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB9_32B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x7 line.long 0x0 "WORD122,Message Buffer 22 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS23,Message Buffer 23 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB15_16B_WORD0_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x3 line.long 0x0 "MB23_8B_CS,Message Buffer 23 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB5_64B_WORD0_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x7 line.long 0x0 "MB9_32B_WORD0_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID23,Message Buffer 23 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB15_16B_WORD1_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x3 line.long 0x0 "MB23_8B_ID,Message Buffer 23 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB5_64B_WORD1_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x7 line.long 0x0 "MB9_32B_WORD1_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB23_8B_WORD0,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB5_64B_WORD2_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB9_32B_WORD2_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x7 line.long 0x0 "WORD023,Message Buffer 23 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB23_8B_WORD1,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB5_64B_WORD3_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB9_32B_WORD3_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x7 line.long 0x0 "WORD123,Message Buffer 23 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS24,Message Buffer 24 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB16_16B_CS_L,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB24_8B_CS,Message Buffer 24 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB5_64B_WORD4_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x200++0x7 line.long 0x0 "MB9_32B_WORD4_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID24,Message Buffer 24 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB16_16B_ID_L,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB24_8B_ID,Message Buffer 24 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB5_64B_WORD5_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x204++0x7 line.long 0x0 "MB9_32B_WORD5_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB24_8B_WORD0,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB5_64B_WORD6_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB9_32B_WORD6_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x7 line.long 0x0 "WORD024,Message Buffer 24 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB24_8B_WORD1,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB5_64B_WORD7_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB9_32B_WORD7_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x7 line.long 0x0 "WORD124,Message Buffer 24 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS25,Message Buffer 25 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB10_32B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB16_16B_WORD2_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x210++0x3 line.long 0x0 "MB25_8B_CS,Message Buffer 25 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x7 line.long 0x0 "MB5_64B_WORD8_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID25,Message Buffer 25 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB10_32B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB16_16B_WORD3_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x214++0x3 line.long 0x0 "MB25_8B_ID,Message Buffer 25 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x7 line.long 0x0 "MB5_64B_WORD9_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB17_16B_CS_L,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x218++0x3 line.long 0x0 "MB25_8B_WORD0,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB5_64B_WORD10_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x218++0x7 line.long 0x0 "WORD025,Message Buffer 25 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB17_16B_ID_L,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x21C++0x3 line.long 0x0 "MB25_8B_WORD1,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB5_64B_WORD11_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x7 line.long 0x0 "WORD125,Message Buffer 25 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS26,Message Buffer 26 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x3 line.long 0x0 "MB10_32B_WORD2_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB17_16B_WORD0_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB26_8B_CS,Message Buffer 26 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x7 line.long 0x0 "MB5_64B_WORD12_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID26,Message Buffer 26 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x3 line.long 0x0 "MB10_32B_WORD3_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB17_16B_WORD1_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB26_8B_ID,Message Buffer 26 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x7 line.long 0x0 "MB5_64B_WORD13_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB17_16B_WORD2_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB26_8B_WORD0,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB5_64B_WORD14_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x228++0x7 line.long 0x0 "WORD026,Message Buffer 26 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB17_16B_WORD3_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB26_8B_WORD1,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB5_64B_WORD15_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x7 line.long 0x0 "WORD126,Message Buffer 26 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS27,Message Buffer 27 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB10_32B_WORD6_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x230++0x3 line.long 0x0 "MB18_16B_CS_L,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB27_8B_CS,Message Buffer 27 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x7 line.long 0x0 "MB6_64B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID27,Message Buffer 27 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB10_32B_WORD7_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x234++0x3 line.long 0x0 "MB18_16B_ID_L,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB27_8B_ID,Message Buffer 27 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x7 line.long 0x0 "MB6_64B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x238++0x3 line.long 0x0 "MB18_16B_WORD0_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB27_8B_WORD0,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB6_64B_WORD0_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x7 line.long 0x0 "WORD027,Message Buffer 27 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x23C++0x3 line.long 0x0 "MB18_16B_WORD1_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB27_8B_WORD1,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB6_64B_WORD1_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x7 line.long 0x0 "WORD127,Message Buffer 27 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS28,Message Buffer 28 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x3 line.long 0x0 "MB11_32B_WORD0_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB18_16B_WORD2_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB28_8B_CS,Message Buffer 28 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x7 line.long 0x0 "MB6_64B_WORD2_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID28,Message Buffer 28 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x3 line.long 0x0 "MB11_32B_WORD1_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB18_16B_WORD3_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB28_8B_ID,Message Buffer 28 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x7 line.long 0x0 "MB6_64B_WORD3_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB19_16B_CS_L,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x248++0x3 line.long 0x0 "MB28_8B_WORD0,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB6_64B_WORD4_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x248++0x7 line.long 0x0 "WORD028,Message Buffer 28 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB19_16B_ID_L,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x24C++0x3 line.long 0x0 "MB28_8B_WORD1,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB6_64B_WORD5_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x7 line.long 0x0 "WORD128,Message Buffer 28 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS29,Message Buffer 29 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x3 line.long 0x0 "MB11_32B_WORD4_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB19_16B_WORD0_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB29_8B_CS,Message Buffer 29 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x7 line.long 0x0 "MB6_64B_WORD6_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID29,Message Buffer 29 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x3 line.long 0x0 "MB11_32B_WORD5_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB19_16B_WORD1_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB29_8B_ID,Message Buffer 29 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x7 line.long 0x0 "MB6_64B_WORD7_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB19_16B_WORD2_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB29_8B_WORD0,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB6_64B_WORD8_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x258++0x7 line.long 0x0 "WORD029,Message Buffer 29 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB19_16B_WORD3_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB29_8B_WORD1,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB6_64B_WORD9_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x7 line.long 0x0 "WORD129,Message Buffer 29 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS30,Message Buffer 30 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB20_16B_CS_L,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB30_8B_CS,Message Buffer 30 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x7 line.long 0x0 "MB6_64B_WORD10_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID30,Message Buffer 30 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB20_16B_ID_L,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB30_8B_ID,Message Buffer 30 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x7 line.long 0x0 "MB6_64B_WORD11_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB30_8B_WORD0,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB6_64B_WORD12_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x268++0x7 line.long 0x0 "WORD030,Message Buffer 30 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB30_8B_WORD1,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB6_64B_WORD13_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x7 line.long 0x0 "WORD130,Message Buffer 30 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS31,Message Buffer 31 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x3 line.long 0x0 "MB20_16B_WORD2_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x270++0x3 line.long 0x0 "MB31_8B_CS,Message Buffer 31 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x7 line.long 0x0 "MB6_64B_WORD14_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID31,Message Buffer 31 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x3 line.long 0x0 "MB20_16B_WORD3_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x274++0x3 line.long 0x0 "MB31_8B_ID,Message Buffer 31 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x7 line.long 0x0 "MB6_64B_WORD15_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD0,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x278++0x7 line.long 0x0 "WORD031,Message Buffer 31 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD1,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x27C++0x7 line.long 0x0 "WORD131,Message Buffer 31 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS32,Message Buffer 32 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_16B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_32B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_64B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x7 line.long 0x0 "MB32_8B_CS,Message Buffer 32 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID32,Message Buffer 32 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_16B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_32B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_64B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x7 line.long 0x0 "MB32_8B_ID,Message Buffer 32 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_32B_WORD0_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_64B_WORD0_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB32_8B_WORD0,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x7 line.long 0x0 "WORD032,Message Buffer 32 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_32B_WORD1_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_64B_WORD1_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB32_8B_WORD1,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x7 line.long 0x0 "WORD132,Message Buffer 32 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS33,Message Buffer 33 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x290++0x3 line.long 0x0 "MB0_16B_WORD2_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_32B_WORD2_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_64B_WORD2_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x7 line.long 0x0 "MB33_8B_CS,Message Buffer 33 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID33,Message Buffer 33 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x294++0x3 line.long 0x0 "MB0_16B_WORD3_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_32B_WORD3_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_64B_WORD3_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x7 line.long 0x0 "MB33_8B_ID,Message Buffer 33 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB0_64B_WORD4_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB1_16B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x298++0x3 line.long 0x0 "MB33_8B_WORD0,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x298++0x7 line.long 0x0 "WORD033,Message Buffer 33 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB0_64B_WORD5_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB1_16B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x29C++0x3 line.long 0x0 "MB33_8B_WORD1,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x7 line.long 0x0 "WORD133,Message Buffer 33 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS34,Message Buffer 34 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A0++0x3 line.long 0x0 "MB0_32B_WORD6_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB0_64B_WORD6_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB1_16B_WORD0_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x7 line.long 0x0 "MB34_8B_CS,Message Buffer 34 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID34,Message Buffer 34 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2A4++0x3 line.long 0x0 "MB0_32B_WORD7_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB0_64B_WORD7_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB1_16B_WORD1_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x7 line.long 0x0 "MB34_8B_ID,Message Buffer 34 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_16B_WORD2_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_32B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A8++0x3 line.long 0x0 "MB34_8B_WORD0,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x7 line.long 0x0 "WORD034,Message Buffer 34 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_16B_WORD3_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_32B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2AC++0x3 line.long 0x0 "MB34_8B_WORD1,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x7 line.long 0x0 "WORD134,Message Buffer 34 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS35,Message Buffer 35 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x3 line.long 0x0 "MB0_64B_WORD10_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB1_32B_WORD0_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB2_16B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x7 line.long 0x0 "MB35_8B_CS,Message Buffer 35 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID35,Message Buffer 35 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x3 line.long 0x0 "MB0_64B_WORD11_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB1_32B_WORD1_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB2_16B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x7 line.long 0x0 "MB35_8B_ID,Message Buffer 35 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB1_32B_WORD2_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB2_16B_WORD0_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB35_8B_WORD0,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x7 line.long 0x0 "WORD035,Message Buffer 35 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB1_32B_WORD3_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB2_16B_WORD1_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB35_8B_WORD1,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x7 line.long 0x0 "WORD135,Message Buffer 35 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS36,Message Buffer 36 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C0++0x3 line.long 0x0 "MB0_64B_WORD14_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB1_32B_WORD4_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB2_16B_WORD2_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x7 line.long 0x0 "MB36_8B_CS,Message Buffer 36 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID36,Message Buffer 36 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2C4++0x3 line.long 0x0 "MB0_64B_WORD15_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB1_32B_WORD5_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB2_16B_WORD3_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x7 line.long 0x0 "MB36_8B_ID,Message Buffer 36 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB1_64B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x3 line.long 0x0 "MB36_8B_WORD0,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB3_16B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x7 line.long 0x0 "WORD036,Message Buffer 36 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB1_64B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x3 line.long 0x0 "MB36_8B_WORD1,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB3_16B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x7 line.long 0x0 "WORD136,Message Buffer 36 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS37,Message Buffer 37 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB1_64B_WORD0_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D0++0x3 line.long 0x0 "MB2_32B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB37_8B_CS,Message Buffer 37 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x7 line.long 0x0 "MB3_16B_WORD0_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID37,Message Buffer 37 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB1_64B_WORD1_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2D4++0x3 line.long 0x0 "MB2_32B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB37_8B_ID,Message Buffer 37 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x7 line.long 0x0 "MB3_16B_WORD1_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD2_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB2_32B_WORD0_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB37_8B_WORD0,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB3_16B_WORD2_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x7 line.long 0x0 "WORD037,Message Buffer 37 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB2_32B_WORD1_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB37_8B_WORD1,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB3_16B_WORD3_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x7 line.long 0x0 "WORD137,Message Buffer 37 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS38,Message Buffer 38 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x3 line.long 0x0 "MB1_64B_WORD4_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB2_32B_WORD2_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB38_8B_CS,Message Buffer 38 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x7 line.long 0x0 "MB4_16B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID38,Message Buffer 38 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x3 line.long 0x0 "MB1_64B_WORD5_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB2_32B_WORD3_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB38_8B_ID,Message Buffer 38 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x7 line.long 0x0 "MB4_16B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB2_32B_WORD4_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB38_8B_WORD0,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB4_16B_WORD0_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x7 line.long 0x0 "WORD038,Message Buffer 38 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB2_32B_WORD5_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB38_8B_WORD1,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB4_16B_WORD1_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x7 line.long 0x0 "WORD138,Message Buffer 38 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS39,Message Buffer 39 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x3 line.long 0x0 "MB1_64B_WORD8_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB2_32B_WORD6_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB39_8B_CS,Message Buffer 39 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x7 line.long 0x0 "MB4_16B_WORD2_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID39,Message Buffer 39 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x3 line.long 0x0 "MB1_64B_WORD9_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB2_32B_WORD7_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB39_8B_ID,Message Buffer 39 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x7 line.long 0x0 "MB4_16B_WORD3_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD10_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB39_8B_WORD0,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB3_32B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x3 line.long 0x0 "MB5_16B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x7 line.long 0x0 "WORD039,Message Buffer 39 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB39_8B_WORD1,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB3_32B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x3 line.long 0x0 "MB5_16B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x7 line.long 0x0 "WORD139,Message Buffer 39 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS40,Message Buffer 40 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x3 line.long 0x0 "MB1_64B_WORD12_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB3_32B_WORD0_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB40_8B_CS,Message Buffer 40 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x7 line.long 0x0 "MB5_16B_WORD0_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID40,Message Buffer 40 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x3 line.long 0x0 "MB1_64B_WORD13_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB3_32B_WORD1_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB40_8B_ID,Message Buffer 40 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x7 line.long 0x0 "MB5_16B_WORD1_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD14_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB3_32B_WORD2_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB40_8B_WORD0,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB5_16B_WORD2_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x7 line.long 0x0 "WORD040,Message Buffer 40 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB3_32B_WORD3_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB40_8B_WORD1,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB5_16B_WORD3_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x7 line.long 0x0 "WORD140,Message Buffer 40 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS41,Message Buffer 41 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB2_64B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB3_32B_WORD4_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x310++0x3 line.long 0x0 "MB41_8B_CS,Message Buffer 41 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x7 line.long 0x0 "MB6_16B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID41,Message Buffer 41 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB2_64B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB3_32B_WORD5_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x314++0x3 line.long 0x0 "MB41_8B_ID,Message Buffer 41 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x7 line.long 0x0 "MB6_16B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB3_32B_WORD6_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB41_8B_WORD0,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB6_16B_WORD0_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x7 line.long 0x0 "WORD041,Message Buffer 41 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB3_32B_WORD7_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB41_8B_WORD1,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB6_16B_WORD1_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x7 line.long 0x0 "WORD141,Message Buffer 41 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS42,Message Buffer 42 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB2_64B_WORD2_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x320++0x3 line.long 0x0 "MB42_8B_CS,Message Buffer 42 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB4_32B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x7 line.long 0x0 "MB6_16B_WORD2_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID42,Message Buffer 42 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB2_64B_WORD3_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x324++0x3 line.long 0x0 "MB42_8B_ID,Message Buffer 42 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB4_32B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x7 line.long 0x0 "MB6_16B_WORD3_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD4_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB42_8B_WORD0,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB4_32B_WORD0_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB7_16B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x328++0x7 line.long 0x0 "WORD042,Message Buffer 42 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD5_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB42_8B_WORD1,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB4_32B_WORD1_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB7_16B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x32C++0x7 line.long 0x0 "WORD142,Message Buffer 42 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS43,Message Buffer 43 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB2_64B_WORD6_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x330++0x3 line.long 0x0 "MB43_8B_CS,Message Buffer 43 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB4_32B_WORD2_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x330++0x7 line.long 0x0 "MB7_16B_WORD0_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID43,Message Buffer 43 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB2_64B_WORD7_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x334++0x3 line.long 0x0 "MB43_8B_ID,Message Buffer 43 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB4_32B_WORD3_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x334++0x7 line.long 0x0 "MB7_16B_WORD1_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD8_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB43_8B_WORD0,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB4_32B_WORD4_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB7_16B_WORD2_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x338++0x7 line.long 0x0 "WORD043,Message Buffer 43 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD9_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB43_8B_WORD1,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB4_32B_WORD5_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB7_16B_WORD3_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x7 line.long 0x0 "WORD143,Message Buffer 43 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS44,Message Buffer 44 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB2_64B_WORD10_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x340++0x3 line.long 0x0 "MB44_8B_CS,Message Buffer 44 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB4_32B_WORD6_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x340++0x7 line.long 0x0 "MB8_16B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID44,Message Buffer 44 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB2_64B_WORD11_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x344++0x3 line.long 0x0 "MB44_8B_ID,Message Buffer 44 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB4_32B_WORD7_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x344++0x7 line.long 0x0 "MB8_16B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD12_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB44_8B_WORD0,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB5_32B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x348++0x3 line.long 0x0 "MB8_16B_WORD0_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x7 line.long 0x0 "WORD044,Message Buffer 44 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD13_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB44_8B_WORD1,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB5_32B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x34C++0x3 line.long 0x0 "MB8_16B_WORD1_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x7 line.long 0x0 "WORD144,Message Buffer 44 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS45,Message Buffer 45 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB2_64B_WORD14_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x350++0x3 line.long 0x0 "MB45_8B_CS,Message Buffer 45 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB5_32B_WORD0_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x350++0x7 line.long 0x0 "MB8_16B_WORD2_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID45,Message Buffer 45 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB2_64B_WORD15_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x354++0x3 line.long 0x0 "MB45_8B_ID,Message Buffer 45 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB5_32B_WORD1_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x354++0x7 line.long 0x0 "MB8_16B_WORD3_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x3 line.long 0x0 "MB45_8B_WORD0,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB5_32B_WORD2_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB9_16B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x7 line.long 0x0 "WORD045,Message Buffer 45 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x3 line.long 0x0 "MB45_8B_WORD1,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB5_32B_WORD3_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB9_16B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x7 line.long 0x0 "WORD145,Message Buffer 45 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS46,Message Buffer 46 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB3_64B_WORD0_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x360++0x3 line.long 0x0 "MB46_8B_CS,Message Buffer 46 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB5_32B_WORD4_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x360++0x7 line.long 0x0 "MB9_16B_WORD0_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID46,Message Buffer 46 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB3_64B_WORD1_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x364++0x3 line.long 0x0 "MB46_8B_ID,Message Buffer 46 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB5_32B_WORD5_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x364++0x7 line.long 0x0 "MB9_16B_WORD1_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD2_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB46_8B_WORD0,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB5_32B_WORD6_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB9_16B_WORD2_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x7 line.long 0x0 "WORD046,Message Buffer 46 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD3_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB46_8B_WORD1,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB5_32B_WORD7_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB9_16B_WORD3_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x7 line.long 0x0 "WORD146,Message Buffer 46 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS47,Message Buffer 47 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB10_16B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB3_64B_WORD4_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x370++0x3 line.long 0x0 "MB47_8B_CS,Message Buffer 47 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x7 line.long 0x0 "MB6_32B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID47,Message Buffer 47 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB10_16B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB3_64B_WORD5_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x374++0x3 line.long 0x0 "MB47_8B_ID,Message Buffer 47 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x7 line.long 0x0 "MB6_32B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB3_64B_WORD6_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB47_8B_WORD0,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB6_32B_WORD0_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x7 line.long 0x0 "WORD047,Message Buffer 47 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB3_64B_WORD7_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB47_8B_WORD1,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB6_32B_WORD1_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x7 line.long 0x0 "WORD147,Message Buffer 47 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS48,Message Buffer 48 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x3 line.long 0x0 "MB10_16B_WORD2_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB3_64B_WORD8_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB48_8B_CS,Message Buffer 48 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x7 line.long 0x0 "MB6_32B_WORD2_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID48,Message Buffer 48 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x3 line.long 0x0 "MB10_16B_WORD3_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB3_64B_WORD9_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB48_8B_ID,Message Buffer 48 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x7 line.long 0x0 "MB6_32B_WORD3_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x388++0x3 line.long 0x0 "MB3_64B_WORD10_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB48_8B_WORD0,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB6_32B_WORD4_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x388++0x7 line.long 0x0 "WORD048,Message Buffer 48 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x38C++0x3 line.long 0x0 "MB3_64B_WORD11_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB48_8B_WORD1,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB6_32B_WORD5_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x7 line.long 0x0 "WORD148,Message Buffer 48 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS49,Message Buffer 49 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x3 line.long 0x0 "MB11_16B_WORD0_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB3_64B_WORD12_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB49_8B_CS,Message Buffer 49 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x7 line.long 0x0 "MB6_32B_WORD6_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID49,Message Buffer 49 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x3 line.long 0x0 "MB11_16B_WORD1_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB3_64B_WORD13_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB49_8B_ID,Message Buffer 49 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x7 line.long 0x0 "MB6_32B_WORD7_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB3_64B_WORD14_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB49_8B_WORD0,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB7_32B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x398++0x7 line.long 0x0 "WORD049,Message Buffer 49 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB3_64B_WORD15_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB49_8B_WORD1,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB7_32B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x39C++0x7 line.long 0x0 "WORD149,Message Buffer 49 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS50,Message Buffer 50 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB12_16B_CS_H,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB4_64B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB50_8B_CS,Message Buffer 50 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x7 line.long 0x0 "MB7_32B_WORD0_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID50,Message Buffer 50 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB12_16B_ID_H,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB4_64B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB50_8B_ID,Message Buffer 50 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x7 line.long 0x0 "MB7_32B_WORD1_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB4_64B_WORD0_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB50_8B_WORD0,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB7_32B_WORD2_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x7 line.long 0x0 "WORD050,Message Buffer 50 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB4_64B_WORD1_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB50_8B_WORD1,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB7_32B_WORD3_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x7 line.long 0x0 "WORD150,Message Buffer 50 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS51,Message Buffer 51 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x3 line.long 0x0 "MB12_16B_WORD2_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB4_64B_WORD2_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB51_8B_CS,Message Buffer 51 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x7 line.long 0x0 "MB7_32B_WORD4_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID51,Message Buffer 51 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x3 line.long 0x0 "MB12_16B_WORD3_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB4_64B_WORD3_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB51_8B_ID,Message Buffer 51 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x7 line.long 0x0 "MB7_32B_WORD5_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_H,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B8++0x3 line.long 0x0 "MB4_64B_WORD4_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB51_8B_WORD0,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB7_32B_WORD6_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x7 line.long 0x0 "WORD051,Message Buffer 51 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_H,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3BC++0x3 line.long 0x0 "MB4_64B_WORD5_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB51_8B_WORD1,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB7_32B_WORD7_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x7 line.long 0x0 "WORD151,Message Buffer 51 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS52,Message Buffer 52 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x3 line.long 0x0 "MB13_16B_WORD0_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB4_64B_WORD6_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB52_8B_CS,Message Buffer 52 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x7 line.long 0x0 "MB8_32B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID52,Message Buffer 52 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x3 line.long 0x0 "MB13_16B_WORD1_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB4_64B_WORD7_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB52_8B_ID,Message Buffer 52 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x7 line.long 0x0 "MB8_32B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB4_64B_WORD8_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB52_8B_WORD0,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB8_32B_WORD0_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x7 line.long 0x0 "WORD052,Message Buffer 52 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB4_64B_WORD9_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB52_8B_WORD1,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB8_32B_WORD1_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x7 line.long 0x0 "WORD152,Message Buffer 52 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS53,Message Buffer 53 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB14_16B_CS_H,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB4_64B_WORD10_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x3D0++0x3 line.long 0x0 "MB53_8B_CS,Message Buffer 53 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x7 line.long 0x0 "MB8_32B_WORD2_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID53,Message Buffer 53 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB14_16B_ID_H,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB4_64B_WORD11_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x3D4++0x3 line.long 0x0 "MB53_8B_ID,Message Buffer 53 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x7 line.long 0x0 "MB8_32B_WORD3_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB4_64B_WORD12_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB53_8B_WORD0,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB8_32B_WORD4_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x7 line.long 0x0 "WORD053,Message Buffer 53 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB4_64B_WORD13_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB53_8B_WORD1,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB8_32B_WORD5_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x7 line.long 0x0 "WORD153,Message Buffer 53 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS54,Message Buffer 54 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x3 line.long 0x0 "MB14_16B_WORD2_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB4_64B_WORD14_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB54_8B_CS,Message Buffer 54 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x7 line.long 0x0 "MB8_32B_WORD6_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID54,Message Buffer 54 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x3 line.long 0x0 "MB14_16B_WORD3_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB4_64B_WORD15_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB54_8B_ID,Message Buffer 54 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x7 line.long 0x0 "MB8_32B_WORD7_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_H,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB54_8B_WORD0,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3E8++0x3 line.long 0x0 "MB5_64B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB9_32B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x7 line.long 0x0 "WORD054,Message Buffer 54 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_H,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB54_8B_WORD1,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3EC++0x3 line.long 0x0 "MB5_64B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB9_32B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x7 line.long 0x0 "WORD154,Message Buffer 54 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS55,Message Buffer 55 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB15_16B_WORD0_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x3 line.long 0x0 "MB55_8B_CS,Message Buffer 55 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB5_64B_WORD0_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x7 line.long 0x0 "MB9_32B_WORD0_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID55,Message Buffer 55 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB15_16B_WORD1_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x3 line.long 0x0 "MB55_8B_ID,Message Buffer 55 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB5_64B_WORD1_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x7 line.long 0x0 "MB9_32B_WORD1_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB55_8B_WORD0,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB5_64B_WORD2_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB9_32B_WORD2_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x7 line.long 0x0 "WORD055,Message Buffer 55 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB55_8B_WORD1,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB5_64B_WORD3_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB9_32B_WORD3_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x7 line.long 0x0 "WORD155,Message Buffer 55 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS56,Message Buffer 56 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB16_16B_CS_H,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB56_8B_CS,Message Buffer 56 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB5_64B_WORD4_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x400++0x7 line.long 0x0 "MB9_32B_WORD4_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID56,Message Buffer 56 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB16_16B_ID_H,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB56_8B_ID,Message Buffer 56 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB5_64B_WORD5_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x404++0x7 line.long 0x0 "MB9_32B_WORD5_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB56_8B_WORD0,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB5_64B_WORD6_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB9_32B_WORD6_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x7 line.long 0x0 "WORD056,Message Buffer 56 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB56_8B_WORD1,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB5_64B_WORD7_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB9_32B_WORD7_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x7 line.long 0x0 "WORD156,Message Buffer 56 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS57,Message Buffer 57 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB10_32B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB16_16B_WORD2_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x410++0x3 line.long 0x0 "MB57_8B_CS,Message Buffer 57 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x7 line.long 0x0 "MB5_64B_WORD8_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID57,Message Buffer 57 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB10_32B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB16_16B_WORD3_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x414++0x3 line.long 0x0 "MB57_8B_ID,Message Buffer 57 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x7 line.long 0x0 "MB5_64B_WORD9_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB17_16B_CS_H,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x418++0x3 line.long 0x0 "MB57_8B_WORD0,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB5_64B_WORD10_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x418++0x7 line.long 0x0 "WORD057,Message Buffer 57 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB17_16B_ID_H,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x41C++0x3 line.long 0x0 "MB57_8B_WORD1,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB5_64B_WORD11_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x7 line.long 0x0 "WORD157,Message Buffer 57 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS58,Message Buffer 58 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x3 line.long 0x0 "MB10_32B_WORD2_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB17_16B_WORD0_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB58_8B_CS,Message Buffer 58 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x7 line.long 0x0 "MB5_64B_WORD12_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID58,Message Buffer 58 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x3 line.long 0x0 "MB10_32B_WORD3_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB17_16B_WORD1_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB58_8B_ID,Message Buffer 58 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x7 line.long 0x0 "MB5_64B_WORD13_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB17_16B_WORD2_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB58_8B_WORD0,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB5_64B_WORD14_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x428++0x7 line.long 0x0 "WORD058,Message Buffer 58 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB17_16B_WORD3_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB58_8B_WORD1,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB5_64B_WORD15_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x7 line.long 0x0 "WORD158,Message Buffer 58 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS59,Message Buffer 59 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB10_32B_WORD6_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x430++0x3 line.long 0x0 "MB18_16B_CS_H,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB59_8B_CS,Message Buffer 59 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x7 line.long 0x0 "MB6_64B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID59,Message Buffer 59 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB10_32B_WORD7_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x434++0x3 line.long 0x0 "MB18_16B_ID_H,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB59_8B_ID,Message Buffer 59 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x7 line.long 0x0 "MB6_64B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x438++0x3 line.long 0x0 "MB18_16B_WORD0_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB59_8B_WORD0,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB6_64B_WORD0_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x7 line.long 0x0 "WORD059,Message Buffer 59 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x43C++0x3 line.long 0x0 "MB18_16B_WORD1_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB59_8B_WORD1,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB6_64B_WORD1_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x7 line.long 0x0 "WORD159,Message Buffer 59 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS60,Message Buffer 60 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x3 line.long 0x0 "MB11_32B_WORD0_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB18_16B_WORD2_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB60_8B_CS,Message Buffer 60 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x7 line.long 0x0 "MB6_64B_WORD2_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID60,Message Buffer 60 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x3 line.long 0x0 "MB11_32B_WORD1_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB18_16B_WORD3_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB60_8B_ID,Message Buffer 60 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x7 line.long 0x0 "MB6_64B_WORD3_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB19_16B_CS_H,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x448++0x3 line.long 0x0 "MB60_8B_WORD0,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB6_64B_WORD4_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x448++0x7 line.long 0x0 "WORD060,Message Buffer 60 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB19_16B_ID_H,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x44C++0x3 line.long 0x0 "MB60_8B_WORD1,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB6_64B_WORD5_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x7 line.long 0x0 "WORD160,Message Buffer 60 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS61,Message Buffer 61 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x3 line.long 0x0 "MB11_32B_WORD4_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB19_16B_WORD0_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB61_8B_CS,Message Buffer 61 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x7 line.long 0x0 "MB6_64B_WORD6_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID61,Message Buffer 61 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x3 line.long 0x0 "MB11_32B_WORD5_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB19_16B_WORD1_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB61_8B_ID,Message Buffer 61 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x7 line.long 0x0 "MB6_64B_WORD7_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB19_16B_WORD2_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB61_8B_WORD0,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB6_64B_WORD8_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x458++0x7 line.long 0x0 "WORD061,Message Buffer 61 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB19_16B_WORD3_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB61_8B_WORD1,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB6_64B_WORD9_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x7 line.long 0x0 "WORD161,Message Buffer 61 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS62,Message Buffer 62 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB20_16B_CS_H,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB62_8B_CS,Message Buffer 62 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x7 line.long 0x0 "MB6_64B_WORD10_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID62,Message Buffer 62 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB20_16B_ID_H,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB62_8B_ID,Message Buffer 62 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x7 line.long 0x0 "MB6_64B_WORD11_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB62_8B_WORD0,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB6_64B_WORD12_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x468++0x7 line.long 0x0 "WORD062,Message Buffer 62 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB62_8B_WORD1,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB6_64B_WORD13_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x7 line.long 0x0 "WORD162,Message Buffer 62 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS63,Message Buffer 63 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x3 line.long 0x0 "MB20_16B_WORD2_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x470++0x3 line.long 0x0 "MB63_8B_CS,Message Buffer 63 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x7 line.long 0x0 "MB6_64B_WORD14_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID63,Message Buffer 63 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x3 line.long 0x0 "MB20_16B_WORD3_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x474++0x3 line.long 0x0 "MB63_8B_ID,Message Buffer 63 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x7 line.long 0x0 "MB6_64B_WORD15_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD0,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x478++0x7 line.long 0x0 "WORD063,Message Buffer 63 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD1,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x47C++0x3 line.long 0x0 "WORD163,Message Buffer 63 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." repeat 64. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x880)++0x3 line.long 0x0 "RXIMR[$1],Rx Individual Mask registers" hexmask.long 0x0 0.--31. 1. "MI,Individual Mask Bits" repeat.end group.long 0xAE0++0xF line.long 0x0 "MECR,Memory Error Control register" bitfld.long 0x0 31. "ECRWRDIS,Error Configuration Register Write Disable" "0: Write is enabled.,1: Write is disabled." bitfld.long 0x0 19. "HANCEI_MSK,Host Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 18. "FANCEI_MSK,FlexCAN Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 16. "CEI_MSK,Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 15. "HAERRIE,Host Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." bitfld.long 0x0 14. "FAERRIE,FlexCAN Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." newline bitfld.long 0x0 13. "EXTERRIE,Extended Error Injection Enable" "0: Error injection is applied only to the 32-bit..,1: Error injection is applied to the 64-bit word." bitfld.long 0x0 9. "RERRDIS,Error Report Disable" "0: Enable updates of the error report registers.,1: Disable updates of the error report registers." newline bitfld.long 0x0 8. "ECCDIS,Error Correction Disable" "0: Enable memory error correction.,1: Disable memory error correction." bitfld.long 0x0 7. "NCEFAFRZ,Non-Correctable Errors In FlexCAN Access Put Device In Freeze Mode" "0: Keep normal operation.,1: Put FlexCAN in Freeze mode (see section 'Freeze.." line.long 0x4 "ERRIAR,Error Injection Address register" hexmask.long.word 0x4 2.--13. 1. "INJADDR_H,Error Injection Address High" rbitfld.long 0x4 0.--1. "INJADDR_L,Error Injection Address Low" "0,1,2,3" line.long 0x8 "ERRIDPR,Error Injection Data Pattern register" hexmask.long 0x8 0.--31. 1. "DFLIP,Data flip pattern" line.long 0xC "ERRIPPR,Error Injection Parity Pattern register" hexmask.long.byte 0xC 24.--28. 1. "PFLIP3,Parity Flip Pattern For Byte 3 (most significant)" hexmask.long.byte 0xC 16.--20. 1. "PFLIP2,Parity Flip Pattern For Byte 2" newline hexmask.long.byte 0xC 8.--12. 1. "PFLIP1,Parity Flip Pattern For Byte 1" hexmask.long.byte 0xC 0.--4. 1. "PFLIP0,Parity Flip Pattern For Byte 0 (Least Significant)" rgroup.long 0xAF0++0xB line.long 0x0 "RERRAR,Error Report Address register" bitfld.long 0x0 24. "NCE,Non-Correctable Error" "0: Reporting a correctable error,1: Reporting a non-correctable error" bitfld.long 0x0 16.--18. "SAID,SAID" "0,1,2,3,4,5,6,7" newline hexmask.long.word 0x0 0.--13. 1. "ERRADDR,Address Where Error Detected" line.long 0x4 "RERRDR,Error Report Data register" hexmask.long 0x4 0.--31. 1. "RDATA,Raw data word read from memory with error" line.long 0x8 "RERRSYNR,Error Report Syndrome register" bitfld.long 0x8 31. "BE3,Byte Enabled For Byte 3 (most significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 24.--28. 1. "SYND3,Error Syndrome For Byte 3 (most significant)" newline bitfld.long 0x8 23. "BE2,Byte Enabled For Byte 2" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 16.--20. 1. "SYND2,Error Syndrome For Byte 2" newline bitfld.long 0x8 15. "BE1,Byte Enabled For Byte 1" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 8.--12. 1. "SYND1,Error Syndrome for Byte 1" newline bitfld.long 0x8 7. "BE0,Byte Enabled For Byte 0 (least significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 0.--4. 1. "SYND0,Error Syndrome For Byte 0 (least significant)" group.long 0xAFC++0x3 line.long 0x0 "ERRSR,Error Status register" eventfld.long 0x0 19. "HANCEIF,Host Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in host..,1: A non-correctable error was detected in a host.." eventfld.long 0x0 18. "FANCEIF,FlexCAN Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in..,1: A non-correctable error was detected in a.." newline eventfld.long 0x0 16. "CEIF,Correctable Error Interrupt Flag" "0: No correctable errors were detected so far.,1: A correctable error was detected." eventfld.long 0x0 3. "HANCEIOF,Host Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in host..,1: Overrun on non-correctable errors in host access" newline eventfld.long 0x0 2. "FANCEIOF,FlexCAN Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in FlexCAN..,1: Overrun on non-correctable errors in FlexCAN.." eventfld.long 0x0 0. "CEIOF,Correctable Error Interrupt Overrun Flag" "0: No overrun on correctable errors,1: Overrun on correctable errors" group.long 0xC00++0x7 line.long 0x0 "FDCTRL,CAN FD Control register" bitfld.long 0x0 31. "FDRATE,Bit Rate Switch Enable" "0: Transmit a frame in nominal rate. The BRS bit in..,1: Transmit a frame with bit rate switching if the.." bitfld.long 0x0 19.--20. "MBDSR1,Message Buffer Data Size for Region 1" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." newline bitfld.long 0x0 16.--17. "MBDSR0,Message Buffer Data Size for Region 0" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." bitfld.long 0x0 15. "TDCEN,Transceiver Delay Compensation Enable" "0: TDC is disabled,1: TDC is enabled" newline eventfld.long 0x0 14. "TDCFAIL,Transceiver Delay Compensation Fail" "0: Measured loop delay is in range.,1: Measured loop delay is out of range." hexmask.long.byte 0x0 8.--12. 1. "TDCOFF,Transceiver Delay Compensation Offset" newline hexmask.long.byte 0x0 0.--5. 1. "TDCVAL,Transceiver Delay Compensation Value" line.long 0x4 "FDCBT,CAN FD Bit Timing register" hexmask.long.word 0x4 20.--29. 1. "FPRESDIV,Fast Prescaler Division Factor" bitfld.long 0x4 16.--18. "FRJW,Fast Resync Jump Width" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 10.--14. 1. "FPROPSEG,Fast Propagation Segment" bitfld.long 0x4 5.--7. "FPSEG1,Fast Phase Segment 1" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "FPSEG2,Fast Phase Segment 2" "0,1,2,3,4,5,6,7" rgroup.long 0xC08++0x3 line.long 0x0 "FDCRC,CAN FD CRC register" hexmask.long.byte 0x0 24.--30. 1. "FD_MBCRC,CRC Mailbox Number for FD_TXCRC" hexmask.long.tbyte 0x0 0.--20. 1. "FD_TXCRC,Extended Transmitted CRC value" tree.end tree "CAN2" base ad:0x400C8000 group.long 0x0++0xB line.long 0x0 "MCR,Module Configuration register" bitfld.long 0x0 31. "MDIS,Module Disable" "0: Enable the FlexCAN module.,1: Disable the FlexCAN module." bitfld.long 0x0 30. "FRZ,Freeze Enable" "0: Not enabled to enter Freeze mode.,1: Enabled to enter Freeze mode." newline bitfld.long 0x0 29. "RFEN,Rx FIFO Enable" "0: Rx FIFO not enabled.,1: Rx FIFO enabled." bitfld.long 0x0 28. "HALT,Halt FlexCAN" "0: No Freeze mode request.,1: Enters Freeze mode if the FRZ bit is asserted." newline rbitfld.long 0x0 27. "NOTRDY,FlexCAN Not Ready" "0: FlexCAN module is either in Normal mode..,1: FlexCAN module is either in Disable mode Doze.." bitfld.long 0x0 26. "WAKMSK,Wake Up Interrupt Mask" "0: Wake Up interrupt is disabled.,1: Wake Up interrupt is enabled." newline bitfld.long 0x0 25. "SOFTRST,Soft Reset" "0: No reset request.,1: Resets the registers affected by soft reset." rbitfld.long 0x0 24. "FRZACK,Freeze Mode Acknowledge" "0: FlexCAN not in Freeze mode prescaler running.,1: FlexCAN in Freeze mode prescaler stopped." newline bitfld.long 0x0 23. "SUPV,Supervisor Mode" "0: FlexCAN is in User mode. Affected registers..,1: FlexCAN is in Supervisor mode. Affected.." bitfld.long 0x0 22. "SLFWAK,Self Wake Up" "0: FlexCAN Self Wake Up feature is disabled.,1: FlexCAN Self Wake Up feature is enabled." newline bitfld.long 0x0 21. "WRNEN,Warning Interrupt Enable" "0: TWRNINT and RWRNINT bits are zero independent of..,1: TWRNINT and RWRNINT bits are set when the.." rbitfld.long 0x0 20. "LPMACK,Low-Power Mode Acknowledge" "0: FlexCAN is not in a low-power mode.,1: FlexCAN is in a low-power mode." newline bitfld.long 0x0 19. "WAKSRC,Wake Up Source" "0: FlexCAN uses the unfiltered Rx input to detect..,1: FlexCAN uses the filtered Rx input to detect.." bitfld.long 0x0 18. "DOZE,Doze Mode Enable" "0: FlexCAN is not enabled to enter low-power mode..,1: FlexCAN is enabled to enter low-power mode when.." newline bitfld.long 0x0 17. "SRXDIS,Self Reception Disable" "0: Self-reception enabled.,1: Self-reception disabled." bitfld.long 0x0 16. "IRMQ,Individual Rx Masking And Queue Enable" "0: Individual Rx masking and queue feature are..,1: Individual Rx masking and queue feature are.." newline bitfld.long 0x0 15. "DMA,DMA Enable" "0: DMA feature for RX FIFO disabled.,1: DMA feature for RX FIFO enabled." bitfld.long 0x0 13. "LPRIOEN,Local Priority Enable" "0: Local Priority disabled.,1: Local Priority enabled." newline bitfld.long 0x0 12. "AEN,Abort Enable" "0: Abort disabled.,1: Abort enabled." bitfld.long 0x0 11. "FDEN,CAN FD operation enable" "0: CAN FD is disabled. FlexCAN is able to receive..,1: CAN FD is enabled. FlexCAN is able to receive.." newline bitfld.long 0x0 8.--9. "IDAM,ID Acceptance Mode" "0: Format A: One full ID (standard and extended)..,1: Format B: Two full standard IDs or two partial..,2: Format C: Four partial 8-bit standard IDs per ID..,3: Format D: All frames rejected." hexmask.long.byte 0x0 0.--6. 1. "MAXMB,Number Of The Last Message Buffer" line.long 0x4 "CTRL1,Control 1 register" hexmask.long.byte 0x4 24.--31. 1. "PRESDIV,Prescaler Division Factor" bitfld.long 0x4 22.--23. "RJW,Resync Jump Width" "0,1,2,3" newline bitfld.long 0x4 19.--21. "PSEG1,Phase Segment 1" "0,1,2,3,4,5,6,7" bitfld.long 0x4 16.--18. "PSEG2,Phase Segment 2" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 15. "BOFFMSK,Bus Off Interrupt Mask" "0: Bus Off interrupt disabled.,1: Bus Off interrupt enabled." bitfld.long 0x4 14. "ERRMSK,Error Interrupt Mask" "0: Error interrupt disabled.,1: Error interrupt enabled." newline bitfld.long 0x4 13. "CLKSRC,CAN Engine Clock Source" "0: The CAN engine clock source is the oscillator..,1: The CAN engine clock source is the peripheral.." bitfld.long 0x4 12. "LPB,Loop Back Mode" "0: Loop Back disabled.,1: Loop Back enabled." newline bitfld.long 0x4 11. "TWRNMSK,Tx Warning Interrupt Mask" "0: Tx Warning interrupt disabled.,1: Tx Warning interrupt enabled." bitfld.long 0x4 10. "RWRNMSK,Rx Warning Interrupt Mask" "0: Rx Warning interrupt disabled.,1: Rx Warning interrupt enabled." newline bitfld.long 0x4 7. "SMP,CAN Bit Sampling" "0: Just one sample is used to determine the bit..,1: Three samples are used to determine the value of.." bitfld.long 0x4 6. "BOFFREC,Bus Off Recovery" "0: Automatic recovering from Bus Off state enabled.,1: Automatic recovering from Bus Off state disabled." newline bitfld.long 0x4 5. "TSYN,Timer Sync" "0: Timer sync feature disabled,1: Timer sync feature enabled" bitfld.long 0x4 4. "LBUF,Lowest Buffer Transmitted First" "0: Buffer with highest priority is transmitted first.,1: Lowest number buffer is transmitted first." newline bitfld.long 0x4 3. "LOM,Listen-Only Mode" "0: Listen-Only mode is deactivated.,1: FlexCAN module operates in Listen-Only mode." bitfld.long 0x4 0.--2. "PROPSEG,Propagation Segment" "0,1,2,3,4,5,6,7" line.long 0x8 "TIMER,Free Running Timer" hexmask.long.word 0x8 0.--15. 1. "TIMER,Timer Value" group.long 0x10++0x27 line.long 0x0 "RXMGMASK,Rx Mailboxes Global Mask register" hexmask.long 0x0 0.--31. 1. "MG,Rx Mailboxes Global Mask Bits" line.long 0x4 "RX14MASK,Rx 14 Mask register" hexmask.long 0x4 0.--31. 1. "RX14M,Rx Buffer 14 Mask Bits" line.long 0x8 "RX15MASK,Rx 15 Mask register" hexmask.long 0x8 0.--31. 1. "RX15M,Rx Buffer 15 Mask Bits" line.long 0xC "ECR,Error Counter" hexmask.long.byte 0xC 24.--31. 1. "RXERRCNT_FAST,Receive Error Counter for fast bits" hexmask.long.byte 0xC 16.--23. 1. "TXERRCNT_FAST,Transmit Error Counter for fast bits" newline hexmask.long.byte 0xC 8.--15. 1. "RXERRCNT,Receive Error Counter" hexmask.long.byte 0xC 0.--7. 1. "TXERRCNT,Transmit Error Counter" line.long 0x10 "ESR1,Error and Status 1 register" rbitfld.long 0x10 31. "BIT1ERR_FAST,Bit1 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as recessive is received.." rbitfld.long 0x10 30. "BIT0ERR_FAST,Bit0 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." newline rbitfld.long 0x10 28. "CRCERR_FAST,Cyclic Redundancy Check Error in the CRC field of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 27. "FRMERR_FAST,Form Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A form error occurred since last read of this.." newline rbitfld.long 0x10 26. "STFERR_FAST,Stuffing Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A stuffing error occurred since last read of.." eventfld.long 0x10 21. "ERROVR,Error Overrun" "0: Overrun has not occurred.,1: Overrun has occurred." newline eventfld.long 0x10 20. "ERRINT_FAST,Error interrupt for errors detected in Data Phase of CAN FD frames with BRS bit set" "0: No such occurrence.,1: Indicates setting of any error bit detected in.." eventfld.long 0x10 19. "BOFFDONEINT,Bus Off Done Interrupt" "0: No such occurrence.,1: FlexCAN module has completed Bus Off process." newline rbitfld.long 0x10 18. "SYNCH,CAN Synchronization Status" "0: FlexCAN is not synchronized to the CAN bus.,1: FlexCAN is synchronized to the CAN bus." eventfld.long 0x10 17. "TWRNINT,Tx Warning Interrupt Flag" "0: No such occurrence.,1: The Tx error counter transitioned from less than.." newline eventfld.long 0x10 16. "RWRNINT,Rx Warning Interrupt Flag" "0: No such occurrence.,1: The Rx error counter transitioned from less than.." rbitfld.long 0x10 15. "BIT1ERR,Bit1 Error" "0: No such occurrence.,1: At least one bit sent as recessive is received.." newline rbitfld.long 0x10 14. "BIT0ERR,Bit0 Error" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." rbitfld.long 0x10 13. "ACKERR,Acknowledge Error" "0: No such occurrence.,1: An ACK error occurred since last read of this.." newline rbitfld.long 0x10 12. "CRCERR,Cyclic Redundancy Check Error" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 11. "FRMERR,Form Error" "0: No such occurrence.,1: A Form Error occurred since last read of this.." newline rbitfld.long 0x10 10. "STFERR,Stuffing Error" "0: No such occurrence.,1: A stuffing error occurred since last read of.." rbitfld.long 0x10 9. "TXWRN,TX Error Warning" "0: No such occurrence.,1: TXERRCNT is greater than or equal to 96." newline rbitfld.long 0x10 8. "RXWRN,Rx Error Warning" "0: No such occurrence.,1: RXERRCNT is greater than or equal to 96." rbitfld.long 0x10 7. "IDLE,IDLE" "0: No such occurrence.,1: CAN bus is now IDLE." newline rbitfld.long 0x10 6. "TX,FlexCAN In Transmission" "0: FlexCAN is not transmitting a message.,1: FlexCAN is transmitting a message." rbitfld.long 0x10 4.--5. "FLTCONF,Fault Confinement State" "0: Bus Off,1: Error Passive,2: Bus Off,3: Bus Off" newline rbitfld.long 0x10 3. "RX,FlexCAN In Reception" "0: FlexCAN is not receiving a message.,1: FlexCAN is receiving a message." eventfld.long 0x10 2. "BOFFINT,Bus Off Interrupt" "0: No such occurrence.,1: FlexCAN module entered Bus Off state." newline eventfld.long 0x10 1. "ERRINT,Error Interrupt" "0: No such occurrence.,1: Indicates setting of any error bit in the Error.." eventfld.long 0x10 0. "WAKINT,Wake-Up Interrupt" "0: No such occurrence.,1: Indicates a recessive to dominant transition was.." line.long 0x14 "IMASK2,Interrupt Masks 2 register" hexmask.long 0x14 0.--31. 1. "BUF63TO32M,Buffer MBi Mask" line.long 0x18 "IMASK1,Interrupt Masks 1 register" hexmask.long 0x18 0.--31. 1. "BUF31TO0M,Buffer MBi Mask" line.long 0x1C "IFLAG2,Interrupt Flags 2 register" hexmask.long 0x1C 0.--31. 1. "BUF63TO32I,Buffer MBi Interrupt" line.long 0x20 "IFLAG1,Interrupt Flags 1 register" hexmask.long.tbyte 0x20 8.--31. 1. "BUF31TO8I,Buffer MBi Interrupt" eventfld.long 0x20 7. "BUF7I,Buffer MB7 Interrupt Or Rx FIFO Overflow" "0: No occurrence of MB7 completing..,1: MB7 completed transmission/reception when.." newline eventfld.long 0x20 6. "BUF6I,Buffer MB6 Interrupt Or Rx FIFO Warning" "0: No occurrence of MB6 completing..,1: MB6 completed transmission/reception when.." eventfld.long 0x20 5. "BUF5I,Buffer MB5 Interrupt Or Frames available in Rx FIFO" "0: No occurrence of MB5 completing..,1: MB5 completed transmission/reception when.." newline hexmask.long.byte 0x20 1.--4. 1. "BUF4TO1I,Buffer MBi Interrupt Or Reserved" eventfld.long 0x20 0. "BUF0I,Buffer MB0 Interrupt Or Clear FIFO bit" "0: The corresponding buffer has no occurrence of..,1: The corresponding buffer has successfully.." line.long 0x24 "CTRL2,Control 2 register" bitfld.long 0x24 31. "ERRMSK_FAST,Error Interrupt Mask for errors detected in the data phase of fast CAN FD frames" "0: ERRINT_FAST error interrupt disabled.,1: ERRINT_FAST error interrupt enabled." bitfld.long 0x24 30. "BOFFDONEMSK,Bus Off Done Interrupt Mask" "0: Bus off done interrupt disabled.,1: Bus off done interrupt enabled." newline bitfld.long 0x24 29. "ECRWRE,Error-correction Configuration Register Write Enable" "0: Disable update.,1: Enable update." bitfld.long 0x24 28. "WRMFRZ,Write-Access To Memory In Freeze Mode" "0: Maintain the write access restrictions.,1: Enable unrestricted write access to FlexCAN.." newline hexmask.long.byte 0x24 24.--27. 1. "RFFN,Number Of Rx FIFO Filters" hexmask.long.byte 0x24 19.--23. 1. "TASD,Tx Arbitration Start Delay" newline bitfld.long 0x24 18. "MRP,Mailboxes Reception Priority" "0: Matching starts from Rx FIFO and continues on..,1: Matching starts from mailboxes and continues on.." bitfld.long 0x24 17. "RRS,Remote Request Storing" "0: Remote response frame is generated.,1: Remote request frame is stored." newline bitfld.long 0x24 16. "EACEN,Entire Frame Arbitration Field Comparison Enable For Rx Mailboxes" "0: Rx mailbox filter's IDE bit is always compared..,1: Enables the comparison of both Rx mailbox.." bitfld.long 0x24 15. "TIMER_SRC,Timer Source" "0: The free running timer is clocked by the CAN bit..,1: The free running timer is clocked by an external.." newline bitfld.long 0x24 14. "PREXCEN,Protocol Exception Enable" "0: Protocol exception is disabled.,1: Protocol exception is enabled." bitfld.long 0x24 12. "ISOCANFDEN,ISO CAN FD Enable" "0: FlexCAN operates using the non-ISO CAN FD..,1: FlexCAN operates using the ISO CAN FD protocol.." newline bitfld.long 0x24 11. "EDFLTDIS,Edge Filter Disable" "0: Edge filter is enabled,1: Edge filter is disabled" rgroup.long 0x38++0x3 line.long 0x0 "ESR2,Error and Status 2 register" hexmask.long.byte 0x0 16.--22. 1. "LPTM,Lowest Priority Tx Mailbox" bitfld.long 0x0 14. "VPS,Valid Priority Status" "0: Contents of IMB and LPTM are invalid.,1: Contents of IMB and LPTM are valid." newline bitfld.long 0x0 13. "IMB,Inactive Mailbox" "0: If ESR2[VPS] is asserted the ESR2[LPTM] is not..,1: If ESR2[VPS] is asserted there is at least one.." rgroup.long 0x44++0x3 line.long 0x0 "CRCR,CRC register" hexmask.long.byte 0x0 16.--22. 1. "MBCRC,CRC Mailbox" hexmask.long.word 0x0 0.--14. 1. "TXCRC,Transmitted CRC value" group.long 0x48++0x3 line.long 0x0 "RXFGMASK,Rx FIFO Global Mask register" hexmask.long 0x0 0.--31. 1. "FGM,Rx FIFO Global Mask Bits" rgroup.long 0x4C++0x3 line.long 0x0 "RXFIR,Rx FIFO Information register" hexmask.long.word 0x0 0.--8. 1. "IDHIT,Identifier Acceptance Filter Hit Indicator" group.long 0x50++0x3 line.long 0x0 "CBT,CAN Bit Timing register" bitfld.long 0x0 31. "BTF,Bit Timing Format Enable" "0: Extended bit time definitions disabled.,1: Extended bit time definitions enabled." hexmask.long.word 0x0 21.--30. 1. "EPRESDIV,Extended Prescaler Division Factor" newline hexmask.long.byte 0x0 16.--20. 1. "ERJW,Extended Resync Jump Width" hexmask.long.byte 0x0 10.--15. 1. "EPROPSEG,Extended Propagation Segment" newline hexmask.long.byte 0x0 5.--9. 1. "EPSEG1,Extended Phase Segment 1" hexmask.long.byte 0x0 0.--4. 1. "EPSEG2,Extended Phase Segment 2" group.long 0x80++0x3 line.long 0x0 "CS0,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_16B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_32B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_64B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x7 line.long 0x0 "MB0_8B_CS,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID0,Message Buffer 0 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_16B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_32B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_64B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x7 line.long 0x0 "MB0_8B_ID,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_32B_WORD0_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_64B_WORD0_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_8B_WORD0,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x7 line.long 0x0 "WORD00,Message Buffer 0 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_32B_WORD1_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_64B_WORD1_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_8B_WORD1,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x7 line.long 0x0 "WORD10,Message Buffer 0 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS1,Message Buffer 1 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x90++0x3 line.long 0x0 "MB0_16B_WORD2_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_32B_WORD2_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_64B_WORD2_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x7 line.long 0x0 "MB1_8B_CS,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID1,Message Buffer 1 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x94++0x3 line.long 0x0 "MB0_16B_WORD3_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_32B_WORD3_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_64B_WORD3_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x7 line.long 0x0 "MB1_8B_ID,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB0_64B_WORD4_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB1_16B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x98++0x3 line.long 0x0 "MB1_8B_WORD0,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x98++0x7 line.long 0x0 "WORD01,Message Buffer 1 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB0_64B_WORD5_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB1_16B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x9C++0x3 line.long 0x0 "MB1_8B_WORD1,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x7 line.long 0x0 "WORD11,Message Buffer 1 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS2,Message Buffer 2 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA0++0x3 line.long 0x0 "MB0_32B_WORD6_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB0_64B_WORD6_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB1_16B_WORD0_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x7 line.long 0x0 "MB2_8B_CS,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID2,Message Buffer 2 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xA4++0x3 line.long 0x0 "MB0_32B_WORD7_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB0_64B_WORD7_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB1_16B_WORD1_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x7 line.long 0x0 "MB2_8B_ID,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_16B_WORD2_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_32B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA8++0x3 line.long 0x0 "MB2_8B_WORD0,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x7 line.long 0x0 "WORD02,Message Buffer 2 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_16B_WORD3_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_32B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xAC++0x3 line.long 0x0 "MB2_8B_WORD1,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x7 line.long 0x0 "WORD12,Message Buffer 2 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS3,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x3 line.long 0x0 "MB0_64B_WORD10_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB1_32B_WORD0_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB2_16B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x7 line.long 0x0 "MB3_8B_CS,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID3,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x3 line.long 0x0 "MB0_64B_WORD11_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB1_32B_WORD1_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB2_16B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x7 line.long 0x0 "MB3_8B_ID,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB1_32B_WORD2_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB2_16B_WORD0_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB3_8B_WORD0,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x7 line.long 0x0 "WORD03,Message Buffer 3 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB1_32B_WORD3_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB2_16B_WORD1_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB3_8B_WORD1,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x7 line.long 0x0 "WORD13,Message Buffer 3 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS4,Message Buffer 4 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC0++0x3 line.long 0x0 "MB0_64B_WORD14_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB1_32B_WORD4_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB2_16B_WORD2_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x7 line.long 0x0 "MB4_8B_CS,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID4,Message Buffer 4 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xC4++0x3 line.long 0x0 "MB0_64B_WORD15_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB1_32B_WORD5_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB2_16B_WORD3_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x7 line.long 0x0 "MB4_8B_ID,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x3 line.long 0x0 "MB1_64B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB3_16B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB4_8B_WORD0,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x7 line.long 0x0 "WORD04,Message Buffer 4 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x3 line.long 0x0 "MB1_64B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB3_16B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB4_8B_WORD1,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x7 line.long 0x0 "WORD14,Message Buffer 4 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS5,Message Buffer 5 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB1_64B_WORD0_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x3 line.long 0x0 "MB2_32B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB3_16B_WORD0_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x7 line.long 0x0 "MB5_8B_CS,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID5,Message Buffer 5 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB1_64B_WORD1_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x3 line.long 0x0 "MB2_32B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB3_16B_WORD1_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x7 line.long 0x0 "MB5_8B_ID,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD2_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB2_32B_WORD0_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB3_16B_WORD2_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB5_8B_WORD0,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x7 line.long 0x0 "WORD05,Message Buffer 5 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB2_32B_WORD1_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB3_16B_WORD3_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB5_8B_WORD1,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x7 line.long 0x0 "WORD15,Message Buffer 5 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS6,Message Buffer 6 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x3 line.long 0x0 "MB1_64B_WORD4_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB2_32B_WORD2_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB4_16B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x7 line.long 0x0 "MB6_8B_CS,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID6,Message Buffer 6 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x3 line.long 0x0 "MB1_64B_WORD5_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB2_32B_WORD3_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB4_16B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x7 line.long 0x0 "MB6_8B_ID,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB2_32B_WORD4_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB4_16B_WORD0_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB6_8B_WORD0,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x7 line.long 0x0 "WORD06,Message Buffer 6 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB2_32B_WORD5_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB4_16B_WORD1_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB6_8B_WORD1,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x7 line.long 0x0 "WORD16,Message Buffer 6 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS7,Message Buffer 7 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF0++0x3 line.long 0x0 "MB1_64B_WORD8_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB2_32B_WORD6_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB4_16B_WORD2_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x7 line.long 0x0 "MB7_8B_CS,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID7,Message Buffer 7 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xF4++0x3 line.long 0x0 "MB1_64B_WORD9_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB2_32B_WORD7_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB4_16B_WORD3_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x7 line.long 0x0 "MB7_8B_ID,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD10_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x3 line.long 0x0 "MB3_32B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB5_16B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB7_8B_WORD0,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x7 line.long 0x0 "WORD07,Message Buffer 7 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x3 line.long 0x0 "MB3_32B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB5_16B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB7_8B_WORD1,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x7 line.long 0x0 "WORD17,Message Buffer 7 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS8,Message Buffer 8 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x100++0x3 line.long 0x0 "MB1_64B_WORD12_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB3_32B_WORD0_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB5_16B_WORD0_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x7 line.long 0x0 "MB8_8B_CS,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID8,Message Buffer 8 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x104++0x3 line.long 0x0 "MB1_64B_WORD13_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB3_32B_WORD1_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB5_16B_WORD1_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x7 line.long 0x0 "MB8_8B_ID,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD14_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB3_32B_WORD2_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB5_16B_WORD2_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB8_8B_WORD0,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x108++0x7 line.long 0x0 "WORD08,Message Buffer 8 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB3_32B_WORD3_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB5_16B_WORD3_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB8_8B_WORD1,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x7 line.long 0x0 "WORD18,Message Buffer 8 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS9,Message Buffer 9 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB2_64B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB3_32B_WORD4_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x110++0x3 line.long 0x0 "MB6_16B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x7 line.long 0x0 "MB9_8B_CS,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID9,Message Buffer 9 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB2_64B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB3_32B_WORD5_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x114++0x3 line.long 0x0 "MB6_16B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x7 line.long 0x0 "MB9_8B_ID,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB3_32B_WORD6_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB6_16B_WORD0_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB9_8B_WORD0,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x7 line.long 0x0 "WORD09,Message Buffer 9 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB3_32B_WORD7_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB6_16B_WORD1_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB9_8B_WORD1,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x7 line.long 0x0 "WORD19,Message Buffer 9 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS10,Message Buffer 10 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB10_8B_CS,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB2_64B_WORD2_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x120++0x3 line.long 0x0 "MB4_32B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x7 line.long 0x0 "MB6_16B_WORD2_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID10,Message Buffer 10 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB10_8B_ID,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB2_64B_WORD3_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x124++0x3 line.long 0x0 "MB4_32B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x7 line.long 0x0 "MB6_16B_WORD3_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD0,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB2_64B_WORD4_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB4_32B_WORD0_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB7_16B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x128++0x7 line.long 0x0 "WORD010,Message Buffer 10 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD1,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB2_64B_WORD5_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB4_32B_WORD1_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB7_16B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x12C++0x7 line.long 0x0 "WORD110,Message Buffer 10 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS11,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB11_8B_CS,Message Buffer 11 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB2_64B_WORD6_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x130++0x3 line.long 0x0 "MB4_32B_WORD2_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x130++0x7 line.long 0x0 "MB7_16B_WORD0_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID11,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB11_8B_ID,Message Buffer 11 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB2_64B_WORD7_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x134++0x3 line.long 0x0 "MB4_32B_WORD3_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x134++0x7 line.long 0x0 "MB7_16B_WORD1_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD0,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB2_64B_WORD8_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB4_32B_WORD4_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB7_16B_WORD2_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x138++0x7 line.long 0x0 "WORD011,Message Buffer 11 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD1,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB2_64B_WORD9_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB4_32B_WORD5_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB7_16B_WORD3_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x7 line.long 0x0 "WORD111,Message Buffer 11 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS12,Message Buffer 12 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB12_8B_CS,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB2_64B_WORD10_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x140++0x3 line.long 0x0 "MB4_32B_WORD6_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x140++0x7 line.long 0x0 "MB8_16B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID12,Message Buffer 12 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB12_8B_ID,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB2_64B_WORD11_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x144++0x3 line.long 0x0 "MB4_32B_WORD7_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x144++0x7 line.long 0x0 "MB8_16B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB12_8B_WORD0,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB2_64B_WORD12_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB5_32B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x148++0x3 line.long 0x0 "MB8_16B_WORD0_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x7 line.long 0x0 "WORD012,Message Buffer 12 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_8B_WORD1,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB2_64B_WORD13_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB5_32B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x14C++0x3 line.long 0x0 "MB8_16B_WORD1_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x7 line.long 0x0 "WORD112,Message Buffer 12 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS13,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB13_8B_CS,Message Buffer 13 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB2_64B_WORD14_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x150++0x3 line.long 0x0 "MB5_32B_WORD0_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x150++0x7 line.long 0x0 "MB8_16B_WORD2_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID13,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB13_8B_ID,Message Buffer 13 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB2_64B_WORD15_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x154++0x3 line.long 0x0 "MB5_32B_WORD1_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x154++0x7 line.long 0x0 "MB8_16B_WORD3_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD0,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB3_64B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x3 line.long 0x0 "MB5_32B_WORD2_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB9_16B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x7 line.long 0x0 "WORD013,Message Buffer 13 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD1,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB3_64B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x3 line.long 0x0 "MB5_32B_WORD3_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB9_16B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x7 line.long 0x0 "WORD113,Message Buffer 13 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS14,Message Buffer 14 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB14_8B_CS,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB3_64B_WORD0_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x160++0x3 line.long 0x0 "MB5_32B_WORD4_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x160++0x7 line.long 0x0 "MB9_16B_WORD0_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID14,Message Buffer 14 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB14_8B_ID,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB3_64B_WORD1_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x164++0x3 line.long 0x0 "MB5_32B_WORD5_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x164++0x7 line.long 0x0 "MB9_16B_WORD1_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD0,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB3_64B_WORD2_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB5_32B_WORD6_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB9_16B_WORD2_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x7 line.long 0x0 "WORD014,Message Buffer 14 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD1,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB3_64B_WORD3_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB5_32B_WORD7_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB9_16B_WORD3_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x7 line.long 0x0 "WORD114,Message Buffer 14 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS15,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB10_16B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB15_8B_CS,Message Buffer 15 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB3_64B_WORD4_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x170++0x7 line.long 0x0 "MB6_32B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID15,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB10_16B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB15_8B_ID,Message Buffer 15 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB3_64B_WORD5_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x174++0x7 line.long 0x0 "MB6_32B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB15_8B_WORD0,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB3_64B_WORD6_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB6_32B_WORD0_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x7 line.long 0x0 "WORD015,Message Buffer 15 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB15_8B_WORD1,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB3_64B_WORD7_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB6_32B_WORD1_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x7 line.long 0x0 "WORD115,Message Buffer 15 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS16,Message Buffer 16 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB10_16B_WORD2_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x180++0x3 line.long 0x0 "MB16_8B_CS,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB3_64B_WORD8_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x180++0x7 line.long 0x0 "MB6_32B_WORD2_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID16,Message Buffer 16 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB10_16B_WORD3_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x184++0x3 line.long 0x0 "MB16_8B_ID,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB3_64B_WORD9_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x184++0x7 line.long 0x0 "MB6_32B_WORD3_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x188++0x3 line.long 0x0 "MB16_8B_WORD0,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB3_64B_WORD10_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB6_32B_WORD4_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x188++0x7 line.long 0x0 "WORD016,Message Buffer 16 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x18C++0x3 line.long 0x0 "MB16_8B_WORD1,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB3_64B_WORD11_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB6_32B_WORD5_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x7 line.long 0x0 "WORD116,Message Buffer 16 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS17,Message Buffer 17 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB11_16B_WORD0_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x190++0x3 line.long 0x0 "MB17_8B_CS,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB3_64B_WORD12_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x190++0x7 line.long 0x0 "MB6_32B_WORD6_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID17,Message Buffer 17 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB11_16B_WORD1_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x194++0x3 line.long 0x0 "MB17_8B_ID,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB3_64B_WORD13_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x194++0x7 line.long 0x0 "MB6_32B_WORD7_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB17_8B_WORD0,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB3_64B_WORD14_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB7_32B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x198++0x7 line.long 0x0 "WORD017,Message Buffer 17 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB17_8B_WORD1,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB3_64B_WORD15_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB7_32B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x19C++0x7 line.long 0x0 "WORD117,Message Buffer 17 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS18,Message Buffer 18 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB12_16B_CS_L,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB18_8B_CS,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB4_64B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x7 line.long 0x0 "MB7_32B_WORD0_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID18,Message Buffer 18 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB12_16B_ID_L,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB18_8B_ID,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB4_64B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x7 line.long 0x0 "MB7_32B_WORD1_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB18_8B_WORD0,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB4_64B_WORD0_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB7_32B_WORD2_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x7 line.long 0x0 "WORD018,Message Buffer 18 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB18_8B_WORD1,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB4_64B_WORD1_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB7_32B_WORD3_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x7 line.long 0x0 "WORD118,Message Buffer 18 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS19,Message Buffer 19 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB12_16B_WORD2_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x3 line.long 0x0 "MB19_8B_CS,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB4_64B_WORD2_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x7 line.long 0x0 "MB7_32B_WORD4_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID19,Message Buffer 19 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB12_16B_WORD3_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x3 line.long 0x0 "MB19_8B_ID,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB4_64B_WORD3_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x7 line.long 0x0 "MB7_32B_WORD5_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_L,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B8++0x3 line.long 0x0 "MB19_8B_WORD0,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB4_64B_WORD4_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB7_32B_WORD6_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x7 line.long 0x0 "WORD019,Message Buffer 19 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_L,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1BC++0x3 line.long 0x0 "MB19_8B_WORD1,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB4_64B_WORD5_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB7_32B_WORD7_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x7 line.long 0x0 "WORD119,Message Buffer 19 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS20,Message Buffer 20 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB13_16B_WORD0_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x3 line.long 0x0 "MB20_8B_CS,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB4_64B_WORD6_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x7 line.long 0x0 "MB8_32B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID20,Message Buffer 20 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB13_16B_WORD1_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x3 line.long 0x0 "MB20_8B_ID,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB4_64B_WORD7_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x7 line.long 0x0 "MB8_32B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB20_8B_WORD0,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB4_64B_WORD8_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB8_32B_WORD0_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x7 line.long 0x0 "WORD020,Message Buffer 20 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB20_8B_WORD1,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB4_64B_WORD9_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB8_32B_WORD1_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x7 line.long 0x0 "WORD120,Message Buffer 20 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS21,Message Buffer 21 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB14_16B_CS_L,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB21_8B_CS,Message Buffer 21 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB4_64B_WORD10_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x1D0++0x7 line.long 0x0 "MB8_32B_WORD2_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID21,Message Buffer 21 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB14_16B_ID_L,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB21_8B_ID,Message Buffer 21 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB4_64B_WORD11_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x1D4++0x7 line.long 0x0 "MB8_32B_WORD3_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB21_8B_WORD0,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB4_64B_WORD12_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB8_32B_WORD4_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x7 line.long 0x0 "WORD021,Message Buffer 21 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB21_8B_WORD1,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB4_64B_WORD13_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB8_32B_WORD5_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x7 line.long 0x0 "WORD121,Message Buffer 21 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS22,Message Buffer 22 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB14_16B_WORD2_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x3 line.long 0x0 "MB22_8B_CS,Message Buffer 22 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB4_64B_WORD14_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x7 line.long 0x0 "MB8_32B_WORD6_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID22,Message Buffer 22 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB14_16B_WORD3_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x3 line.long 0x0 "MB22_8B_ID,Message Buffer 22 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB4_64B_WORD15_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x7 line.long 0x0 "MB8_32B_WORD7_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_L,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB22_8B_WORD0,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1E8++0x3 line.long 0x0 "MB5_64B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB9_32B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x7 line.long 0x0 "WORD022,Message Buffer 22 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_L,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB22_8B_WORD1,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1EC++0x3 line.long 0x0 "MB5_64B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB9_32B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x7 line.long 0x0 "WORD122,Message Buffer 22 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS23,Message Buffer 23 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB15_16B_WORD0_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x3 line.long 0x0 "MB23_8B_CS,Message Buffer 23 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB5_64B_WORD0_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x7 line.long 0x0 "MB9_32B_WORD0_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID23,Message Buffer 23 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB15_16B_WORD1_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x3 line.long 0x0 "MB23_8B_ID,Message Buffer 23 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB5_64B_WORD1_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x7 line.long 0x0 "MB9_32B_WORD1_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB23_8B_WORD0,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB5_64B_WORD2_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB9_32B_WORD2_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x7 line.long 0x0 "WORD023,Message Buffer 23 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB23_8B_WORD1,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB5_64B_WORD3_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB9_32B_WORD3_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x7 line.long 0x0 "WORD123,Message Buffer 23 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS24,Message Buffer 24 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB16_16B_CS_L,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB24_8B_CS,Message Buffer 24 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB5_64B_WORD4_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x200++0x7 line.long 0x0 "MB9_32B_WORD4_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID24,Message Buffer 24 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB16_16B_ID_L,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB24_8B_ID,Message Buffer 24 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB5_64B_WORD5_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x204++0x7 line.long 0x0 "MB9_32B_WORD5_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB24_8B_WORD0,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB5_64B_WORD6_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB9_32B_WORD6_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x7 line.long 0x0 "WORD024,Message Buffer 24 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB24_8B_WORD1,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB5_64B_WORD7_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB9_32B_WORD7_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x7 line.long 0x0 "WORD124,Message Buffer 24 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS25,Message Buffer 25 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB10_32B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB16_16B_WORD2_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x210++0x3 line.long 0x0 "MB25_8B_CS,Message Buffer 25 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x7 line.long 0x0 "MB5_64B_WORD8_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID25,Message Buffer 25 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB10_32B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB16_16B_WORD3_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x214++0x3 line.long 0x0 "MB25_8B_ID,Message Buffer 25 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x7 line.long 0x0 "MB5_64B_WORD9_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB17_16B_CS_L,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x218++0x3 line.long 0x0 "MB25_8B_WORD0,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB5_64B_WORD10_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x218++0x7 line.long 0x0 "WORD025,Message Buffer 25 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB17_16B_ID_L,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x21C++0x3 line.long 0x0 "MB25_8B_WORD1,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB5_64B_WORD11_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x7 line.long 0x0 "WORD125,Message Buffer 25 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS26,Message Buffer 26 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x3 line.long 0x0 "MB10_32B_WORD2_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB17_16B_WORD0_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB26_8B_CS,Message Buffer 26 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x7 line.long 0x0 "MB5_64B_WORD12_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID26,Message Buffer 26 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x3 line.long 0x0 "MB10_32B_WORD3_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB17_16B_WORD1_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB26_8B_ID,Message Buffer 26 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x7 line.long 0x0 "MB5_64B_WORD13_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB17_16B_WORD2_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB26_8B_WORD0,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB5_64B_WORD14_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x228++0x7 line.long 0x0 "WORD026,Message Buffer 26 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB17_16B_WORD3_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB26_8B_WORD1,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB5_64B_WORD15_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x7 line.long 0x0 "WORD126,Message Buffer 26 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS27,Message Buffer 27 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB10_32B_WORD6_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x230++0x3 line.long 0x0 "MB18_16B_CS_L,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB27_8B_CS,Message Buffer 27 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x7 line.long 0x0 "MB6_64B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID27,Message Buffer 27 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB10_32B_WORD7_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x234++0x3 line.long 0x0 "MB18_16B_ID_L,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB27_8B_ID,Message Buffer 27 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x7 line.long 0x0 "MB6_64B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x238++0x3 line.long 0x0 "MB18_16B_WORD0_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB27_8B_WORD0,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB6_64B_WORD0_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x7 line.long 0x0 "WORD027,Message Buffer 27 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x23C++0x3 line.long 0x0 "MB18_16B_WORD1_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB27_8B_WORD1,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB6_64B_WORD1_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x7 line.long 0x0 "WORD127,Message Buffer 27 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS28,Message Buffer 28 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x3 line.long 0x0 "MB11_32B_WORD0_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB18_16B_WORD2_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB28_8B_CS,Message Buffer 28 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x7 line.long 0x0 "MB6_64B_WORD2_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID28,Message Buffer 28 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x3 line.long 0x0 "MB11_32B_WORD1_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB18_16B_WORD3_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB28_8B_ID,Message Buffer 28 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x7 line.long 0x0 "MB6_64B_WORD3_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB19_16B_CS_L,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x248++0x3 line.long 0x0 "MB28_8B_WORD0,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB6_64B_WORD4_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x248++0x7 line.long 0x0 "WORD028,Message Buffer 28 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB19_16B_ID_L,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x24C++0x3 line.long 0x0 "MB28_8B_WORD1,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB6_64B_WORD5_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x7 line.long 0x0 "WORD128,Message Buffer 28 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS29,Message Buffer 29 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x3 line.long 0x0 "MB11_32B_WORD4_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB19_16B_WORD0_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB29_8B_CS,Message Buffer 29 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x7 line.long 0x0 "MB6_64B_WORD6_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID29,Message Buffer 29 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x3 line.long 0x0 "MB11_32B_WORD5_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB19_16B_WORD1_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB29_8B_ID,Message Buffer 29 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x7 line.long 0x0 "MB6_64B_WORD7_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB19_16B_WORD2_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB29_8B_WORD0,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB6_64B_WORD8_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x258++0x7 line.long 0x0 "WORD029,Message Buffer 29 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB19_16B_WORD3_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB29_8B_WORD1,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB6_64B_WORD9_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x7 line.long 0x0 "WORD129,Message Buffer 29 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS30,Message Buffer 30 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB20_16B_CS_L,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB30_8B_CS,Message Buffer 30 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x7 line.long 0x0 "MB6_64B_WORD10_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID30,Message Buffer 30 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB20_16B_ID_L,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB30_8B_ID,Message Buffer 30 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x7 line.long 0x0 "MB6_64B_WORD11_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB30_8B_WORD0,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB6_64B_WORD12_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x268++0x7 line.long 0x0 "WORD030,Message Buffer 30 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB30_8B_WORD1,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB6_64B_WORD13_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x7 line.long 0x0 "WORD130,Message Buffer 30 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS31,Message Buffer 31 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x3 line.long 0x0 "MB20_16B_WORD2_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x270++0x3 line.long 0x0 "MB31_8B_CS,Message Buffer 31 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x7 line.long 0x0 "MB6_64B_WORD14_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID31,Message Buffer 31 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x3 line.long 0x0 "MB20_16B_WORD3_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x274++0x3 line.long 0x0 "MB31_8B_ID,Message Buffer 31 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x7 line.long 0x0 "MB6_64B_WORD15_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD0,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x278++0x7 line.long 0x0 "WORD031,Message Buffer 31 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD1,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x27C++0x7 line.long 0x0 "WORD131,Message Buffer 31 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS32,Message Buffer 32 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_16B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_32B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_64B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x7 line.long 0x0 "MB32_8B_CS,Message Buffer 32 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID32,Message Buffer 32 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_16B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_32B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_64B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x7 line.long 0x0 "MB32_8B_ID,Message Buffer 32 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_32B_WORD0_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_64B_WORD0_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB32_8B_WORD0,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x7 line.long 0x0 "WORD032,Message Buffer 32 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_32B_WORD1_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_64B_WORD1_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB32_8B_WORD1,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x7 line.long 0x0 "WORD132,Message Buffer 32 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS33,Message Buffer 33 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x290++0x3 line.long 0x0 "MB0_16B_WORD2_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_32B_WORD2_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_64B_WORD2_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x7 line.long 0x0 "MB33_8B_CS,Message Buffer 33 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID33,Message Buffer 33 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x294++0x3 line.long 0x0 "MB0_16B_WORD3_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_32B_WORD3_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_64B_WORD3_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x7 line.long 0x0 "MB33_8B_ID,Message Buffer 33 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB0_64B_WORD4_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB1_16B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x298++0x3 line.long 0x0 "MB33_8B_WORD0,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x298++0x7 line.long 0x0 "WORD033,Message Buffer 33 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB0_64B_WORD5_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB1_16B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x29C++0x3 line.long 0x0 "MB33_8B_WORD1,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x7 line.long 0x0 "WORD133,Message Buffer 33 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS34,Message Buffer 34 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A0++0x3 line.long 0x0 "MB0_32B_WORD6_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB0_64B_WORD6_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB1_16B_WORD0_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x7 line.long 0x0 "MB34_8B_CS,Message Buffer 34 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID34,Message Buffer 34 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2A4++0x3 line.long 0x0 "MB0_32B_WORD7_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB0_64B_WORD7_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB1_16B_WORD1_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x7 line.long 0x0 "MB34_8B_ID,Message Buffer 34 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_16B_WORD2_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_32B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A8++0x3 line.long 0x0 "MB34_8B_WORD0,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x7 line.long 0x0 "WORD034,Message Buffer 34 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_16B_WORD3_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_32B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2AC++0x3 line.long 0x0 "MB34_8B_WORD1,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x7 line.long 0x0 "WORD134,Message Buffer 34 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS35,Message Buffer 35 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x3 line.long 0x0 "MB0_64B_WORD10_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB1_32B_WORD0_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB2_16B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x7 line.long 0x0 "MB35_8B_CS,Message Buffer 35 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID35,Message Buffer 35 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x3 line.long 0x0 "MB0_64B_WORD11_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB1_32B_WORD1_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB2_16B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x7 line.long 0x0 "MB35_8B_ID,Message Buffer 35 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB1_32B_WORD2_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB2_16B_WORD0_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB35_8B_WORD0,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x7 line.long 0x0 "WORD035,Message Buffer 35 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB1_32B_WORD3_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB2_16B_WORD1_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB35_8B_WORD1,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x7 line.long 0x0 "WORD135,Message Buffer 35 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS36,Message Buffer 36 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C0++0x3 line.long 0x0 "MB0_64B_WORD14_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB1_32B_WORD4_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB2_16B_WORD2_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x7 line.long 0x0 "MB36_8B_CS,Message Buffer 36 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID36,Message Buffer 36 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2C4++0x3 line.long 0x0 "MB0_64B_WORD15_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB1_32B_WORD5_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB2_16B_WORD3_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x7 line.long 0x0 "MB36_8B_ID,Message Buffer 36 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB1_64B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x3 line.long 0x0 "MB36_8B_WORD0,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB3_16B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x7 line.long 0x0 "WORD036,Message Buffer 36 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB1_64B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x3 line.long 0x0 "MB36_8B_WORD1,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB3_16B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x7 line.long 0x0 "WORD136,Message Buffer 36 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS37,Message Buffer 37 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB1_64B_WORD0_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D0++0x3 line.long 0x0 "MB2_32B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB37_8B_CS,Message Buffer 37 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x7 line.long 0x0 "MB3_16B_WORD0_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID37,Message Buffer 37 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB1_64B_WORD1_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2D4++0x3 line.long 0x0 "MB2_32B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB37_8B_ID,Message Buffer 37 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x7 line.long 0x0 "MB3_16B_WORD1_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD2_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB2_32B_WORD0_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB37_8B_WORD0,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB3_16B_WORD2_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x7 line.long 0x0 "WORD037,Message Buffer 37 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB2_32B_WORD1_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB37_8B_WORD1,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB3_16B_WORD3_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x7 line.long 0x0 "WORD137,Message Buffer 37 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS38,Message Buffer 38 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x3 line.long 0x0 "MB1_64B_WORD4_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB2_32B_WORD2_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB38_8B_CS,Message Buffer 38 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x7 line.long 0x0 "MB4_16B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID38,Message Buffer 38 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x3 line.long 0x0 "MB1_64B_WORD5_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB2_32B_WORD3_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB38_8B_ID,Message Buffer 38 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x7 line.long 0x0 "MB4_16B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB2_32B_WORD4_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB38_8B_WORD0,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB4_16B_WORD0_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x7 line.long 0x0 "WORD038,Message Buffer 38 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB2_32B_WORD5_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB38_8B_WORD1,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB4_16B_WORD1_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x7 line.long 0x0 "WORD138,Message Buffer 38 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS39,Message Buffer 39 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x3 line.long 0x0 "MB1_64B_WORD8_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB2_32B_WORD6_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB39_8B_CS,Message Buffer 39 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x7 line.long 0x0 "MB4_16B_WORD2_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID39,Message Buffer 39 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x3 line.long 0x0 "MB1_64B_WORD9_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB2_32B_WORD7_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB39_8B_ID,Message Buffer 39 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x7 line.long 0x0 "MB4_16B_WORD3_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD10_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB39_8B_WORD0,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB3_32B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x3 line.long 0x0 "MB5_16B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x7 line.long 0x0 "WORD039,Message Buffer 39 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB39_8B_WORD1,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB3_32B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x3 line.long 0x0 "MB5_16B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x7 line.long 0x0 "WORD139,Message Buffer 39 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS40,Message Buffer 40 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x3 line.long 0x0 "MB1_64B_WORD12_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB3_32B_WORD0_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB40_8B_CS,Message Buffer 40 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x7 line.long 0x0 "MB5_16B_WORD0_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID40,Message Buffer 40 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x3 line.long 0x0 "MB1_64B_WORD13_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB3_32B_WORD1_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB40_8B_ID,Message Buffer 40 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x7 line.long 0x0 "MB5_16B_WORD1_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD14_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB3_32B_WORD2_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB40_8B_WORD0,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB5_16B_WORD2_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x7 line.long 0x0 "WORD040,Message Buffer 40 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB3_32B_WORD3_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB40_8B_WORD1,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB5_16B_WORD3_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x7 line.long 0x0 "WORD140,Message Buffer 40 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS41,Message Buffer 41 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB2_64B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB3_32B_WORD4_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x310++0x3 line.long 0x0 "MB41_8B_CS,Message Buffer 41 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x7 line.long 0x0 "MB6_16B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID41,Message Buffer 41 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB2_64B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB3_32B_WORD5_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x314++0x3 line.long 0x0 "MB41_8B_ID,Message Buffer 41 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x7 line.long 0x0 "MB6_16B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB3_32B_WORD6_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB41_8B_WORD0,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB6_16B_WORD0_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x7 line.long 0x0 "WORD041,Message Buffer 41 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB3_32B_WORD7_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB41_8B_WORD1,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB6_16B_WORD1_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x7 line.long 0x0 "WORD141,Message Buffer 41 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS42,Message Buffer 42 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB2_64B_WORD2_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x320++0x3 line.long 0x0 "MB42_8B_CS,Message Buffer 42 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB4_32B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x7 line.long 0x0 "MB6_16B_WORD2_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID42,Message Buffer 42 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB2_64B_WORD3_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x324++0x3 line.long 0x0 "MB42_8B_ID,Message Buffer 42 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB4_32B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x7 line.long 0x0 "MB6_16B_WORD3_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD4_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB42_8B_WORD0,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB4_32B_WORD0_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB7_16B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x328++0x7 line.long 0x0 "WORD042,Message Buffer 42 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD5_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB42_8B_WORD1,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB4_32B_WORD1_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB7_16B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x32C++0x7 line.long 0x0 "WORD142,Message Buffer 42 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS43,Message Buffer 43 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB2_64B_WORD6_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x330++0x3 line.long 0x0 "MB43_8B_CS,Message Buffer 43 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB4_32B_WORD2_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x330++0x7 line.long 0x0 "MB7_16B_WORD0_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID43,Message Buffer 43 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB2_64B_WORD7_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x334++0x3 line.long 0x0 "MB43_8B_ID,Message Buffer 43 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB4_32B_WORD3_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x334++0x7 line.long 0x0 "MB7_16B_WORD1_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD8_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB43_8B_WORD0,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB4_32B_WORD4_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB7_16B_WORD2_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x338++0x7 line.long 0x0 "WORD043,Message Buffer 43 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD9_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB43_8B_WORD1,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB4_32B_WORD5_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB7_16B_WORD3_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x7 line.long 0x0 "WORD143,Message Buffer 43 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS44,Message Buffer 44 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB2_64B_WORD10_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x340++0x3 line.long 0x0 "MB44_8B_CS,Message Buffer 44 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB4_32B_WORD6_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x340++0x7 line.long 0x0 "MB8_16B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID44,Message Buffer 44 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB2_64B_WORD11_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x344++0x3 line.long 0x0 "MB44_8B_ID,Message Buffer 44 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB4_32B_WORD7_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x344++0x7 line.long 0x0 "MB8_16B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD12_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB44_8B_WORD0,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB5_32B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x348++0x3 line.long 0x0 "MB8_16B_WORD0_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x7 line.long 0x0 "WORD044,Message Buffer 44 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD13_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB44_8B_WORD1,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB5_32B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x34C++0x3 line.long 0x0 "MB8_16B_WORD1_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x7 line.long 0x0 "WORD144,Message Buffer 44 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS45,Message Buffer 45 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB2_64B_WORD14_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x350++0x3 line.long 0x0 "MB45_8B_CS,Message Buffer 45 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB5_32B_WORD0_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x350++0x7 line.long 0x0 "MB8_16B_WORD2_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID45,Message Buffer 45 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB2_64B_WORD15_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x354++0x3 line.long 0x0 "MB45_8B_ID,Message Buffer 45 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB5_32B_WORD1_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x354++0x7 line.long 0x0 "MB8_16B_WORD3_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x3 line.long 0x0 "MB45_8B_WORD0,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB5_32B_WORD2_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB9_16B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x7 line.long 0x0 "WORD045,Message Buffer 45 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x3 line.long 0x0 "MB45_8B_WORD1,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB5_32B_WORD3_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB9_16B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x7 line.long 0x0 "WORD145,Message Buffer 45 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS46,Message Buffer 46 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB3_64B_WORD0_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x360++0x3 line.long 0x0 "MB46_8B_CS,Message Buffer 46 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB5_32B_WORD4_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x360++0x7 line.long 0x0 "MB9_16B_WORD0_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID46,Message Buffer 46 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB3_64B_WORD1_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x364++0x3 line.long 0x0 "MB46_8B_ID,Message Buffer 46 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB5_32B_WORD5_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x364++0x7 line.long 0x0 "MB9_16B_WORD1_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD2_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB46_8B_WORD0,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB5_32B_WORD6_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB9_16B_WORD2_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x7 line.long 0x0 "WORD046,Message Buffer 46 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD3_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB46_8B_WORD1,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB5_32B_WORD7_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB9_16B_WORD3_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x7 line.long 0x0 "WORD146,Message Buffer 46 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS47,Message Buffer 47 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB10_16B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB3_64B_WORD4_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x370++0x3 line.long 0x0 "MB47_8B_CS,Message Buffer 47 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x7 line.long 0x0 "MB6_32B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID47,Message Buffer 47 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB10_16B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB3_64B_WORD5_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x374++0x3 line.long 0x0 "MB47_8B_ID,Message Buffer 47 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x7 line.long 0x0 "MB6_32B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB3_64B_WORD6_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB47_8B_WORD0,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB6_32B_WORD0_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x7 line.long 0x0 "WORD047,Message Buffer 47 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB3_64B_WORD7_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB47_8B_WORD1,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB6_32B_WORD1_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x7 line.long 0x0 "WORD147,Message Buffer 47 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS48,Message Buffer 48 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x3 line.long 0x0 "MB10_16B_WORD2_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB3_64B_WORD8_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB48_8B_CS,Message Buffer 48 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x7 line.long 0x0 "MB6_32B_WORD2_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID48,Message Buffer 48 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x3 line.long 0x0 "MB10_16B_WORD3_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB3_64B_WORD9_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB48_8B_ID,Message Buffer 48 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x7 line.long 0x0 "MB6_32B_WORD3_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x388++0x3 line.long 0x0 "MB3_64B_WORD10_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB48_8B_WORD0,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB6_32B_WORD4_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x388++0x7 line.long 0x0 "WORD048,Message Buffer 48 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x38C++0x3 line.long 0x0 "MB3_64B_WORD11_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB48_8B_WORD1,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB6_32B_WORD5_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x7 line.long 0x0 "WORD148,Message Buffer 48 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS49,Message Buffer 49 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x3 line.long 0x0 "MB11_16B_WORD0_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB3_64B_WORD12_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB49_8B_CS,Message Buffer 49 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x7 line.long 0x0 "MB6_32B_WORD6_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID49,Message Buffer 49 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x3 line.long 0x0 "MB11_16B_WORD1_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB3_64B_WORD13_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB49_8B_ID,Message Buffer 49 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x7 line.long 0x0 "MB6_32B_WORD7_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB3_64B_WORD14_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB49_8B_WORD0,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB7_32B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x398++0x7 line.long 0x0 "WORD049,Message Buffer 49 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB3_64B_WORD15_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB49_8B_WORD1,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB7_32B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x39C++0x7 line.long 0x0 "WORD149,Message Buffer 49 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS50,Message Buffer 50 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB12_16B_CS_H,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB4_64B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB50_8B_CS,Message Buffer 50 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x7 line.long 0x0 "MB7_32B_WORD0_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID50,Message Buffer 50 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB12_16B_ID_H,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB4_64B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB50_8B_ID,Message Buffer 50 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x7 line.long 0x0 "MB7_32B_WORD1_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB4_64B_WORD0_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB50_8B_WORD0,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB7_32B_WORD2_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x7 line.long 0x0 "WORD050,Message Buffer 50 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB4_64B_WORD1_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB50_8B_WORD1,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB7_32B_WORD3_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x7 line.long 0x0 "WORD150,Message Buffer 50 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS51,Message Buffer 51 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x3 line.long 0x0 "MB12_16B_WORD2_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB4_64B_WORD2_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB51_8B_CS,Message Buffer 51 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x7 line.long 0x0 "MB7_32B_WORD4_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID51,Message Buffer 51 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x3 line.long 0x0 "MB12_16B_WORD3_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB4_64B_WORD3_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB51_8B_ID,Message Buffer 51 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x7 line.long 0x0 "MB7_32B_WORD5_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_H,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B8++0x3 line.long 0x0 "MB4_64B_WORD4_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB51_8B_WORD0,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB7_32B_WORD6_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x7 line.long 0x0 "WORD051,Message Buffer 51 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_H,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3BC++0x3 line.long 0x0 "MB4_64B_WORD5_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB51_8B_WORD1,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB7_32B_WORD7_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x7 line.long 0x0 "WORD151,Message Buffer 51 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS52,Message Buffer 52 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x3 line.long 0x0 "MB13_16B_WORD0_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB4_64B_WORD6_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB52_8B_CS,Message Buffer 52 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x7 line.long 0x0 "MB8_32B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID52,Message Buffer 52 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x3 line.long 0x0 "MB13_16B_WORD1_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB4_64B_WORD7_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB52_8B_ID,Message Buffer 52 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x7 line.long 0x0 "MB8_32B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB4_64B_WORD8_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB52_8B_WORD0,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB8_32B_WORD0_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x7 line.long 0x0 "WORD052,Message Buffer 52 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB4_64B_WORD9_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB52_8B_WORD1,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB8_32B_WORD1_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x7 line.long 0x0 "WORD152,Message Buffer 52 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS53,Message Buffer 53 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB14_16B_CS_H,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB4_64B_WORD10_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x3D0++0x3 line.long 0x0 "MB53_8B_CS,Message Buffer 53 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x7 line.long 0x0 "MB8_32B_WORD2_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID53,Message Buffer 53 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB14_16B_ID_H,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB4_64B_WORD11_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x3D4++0x3 line.long 0x0 "MB53_8B_ID,Message Buffer 53 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x7 line.long 0x0 "MB8_32B_WORD3_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB4_64B_WORD12_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB53_8B_WORD0,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB8_32B_WORD4_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x7 line.long 0x0 "WORD053,Message Buffer 53 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB4_64B_WORD13_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB53_8B_WORD1,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB8_32B_WORD5_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x7 line.long 0x0 "WORD153,Message Buffer 53 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS54,Message Buffer 54 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x3 line.long 0x0 "MB14_16B_WORD2_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB4_64B_WORD14_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB54_8B_CS,Message Buffer 54 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x7 line.long 0x0 "MB8_32B_WORD6_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID54,Message Buffer 54 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x3 line.long 0x0 "MB14_16B_WORD3_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB4_64B_WORD15_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB54_8B_ID,Message Buffer 54 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x7 line.long 0x0 "MB8_32B_WORD7_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_H,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB54_8B_WORD0,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3E8++0x3 line.long 0x0 "MB5_64B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB9_32B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x7 line.long 0x0 "WORD054,Message Buffer 54 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_H,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB54_8B_WORD1,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3EC++0x3 line.long 0x0 "MB5_64B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB9_32B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x7 line.long 0x0 "WORD154,Message Buffer 54 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS55,Message Buffer 55 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB15_16B_WORD0_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x3 line.long 0x0 "MB55_8B_CS,Message Buffer 55 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB5_64B_WORD0_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x7 line.long 0x0 "MB9_32B_WORD0_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID55,Message Buffer 55 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB15_16B_WORD1_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x3 line.long 0x0 "MB55_8B_ID,Message Buffer 55 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB5_64B_WORD1_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x7 line.long 0x0 "MB9_32B_WORD1_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB55_8B_WORD0,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB5_64B_WORD2_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB9_32B_WORD2_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x7 line.long 0x0 "WORD055,Message Buffer 55 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB55_8B_WORD1,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB5_64B_WORD3_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB9_32B_WORD3_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x7 line.long 0x0 "WORD155,Message Buffer 55 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS56,Message Buffer 56 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB16_16B_CS_H,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB56_8B_CS,Message Buffer 56 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB5_64B_WORD4_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x400++0x7 line.long 0x0 "MB9_32B_WORD4_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID56,Message Buffer 56 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB16_16B_ID_H,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB56_8B_ID,Message Buffer 56 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB5_64B_WORD5_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x404++0x7 line.long 0x0 "MB9_32B_WORD5_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB56_8B_WORD0,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB5_64B_WORD6_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB9_32B_WORD6_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x7 line.long 0x0 "WORD056,Message Buffer 56 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB56_8B_WORD1,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB5_64B_WORD7_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB9_32B_WORD7_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x7 line.long 0x0 "WORD156,Message Buffer 56 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS57,Message Buffer 57 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB10_32B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB16_16B_WORD2_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x410++0x3 line.long 0x0 "MB57_8B_CS,Message Buffer 57 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x7 line.long 0x0 "MB5_64B_WORD8_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID57,Message Buffer 57 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB10_32B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB16_16B_WORD3_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x414++0x3 line.long 0x0 "MB57_8B_ID,Message Buffer 57 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x7 line.long 0x0 "MB5_64B_WORD9_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB17_16B_CS_H,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x418++0x3 line.long 0x0 "MB57_8B_WORD0,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB5_64B_WORD10_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x418++0x7 line.long 0x0 "WORD057,Message Buffer 57 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB17_16B_ID_H,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x41C++0x3 line.long 0x0 "MB57_8B_WORD1,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB5_64B_WORD11_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x7 line.long 0x0 "WORD157,Message Buffer 57 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS58,Message Buffer 58 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x3 line.long 0x0 "MB10_32B_WORD2_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB17_16B_WORD0_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB58_8B_CS,Message Buffer 58 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x7 line.long 0x0 "MB5_64B_WORD12_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID58,Message Buffer 58 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x3 line.long 0x0 "MB10_32B_WORD3_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB17_16B_WORD1_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB58_8B_ID,Message Buffer 58 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x7 line.long 0x0 "MB5_64B_WORD13_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB17_16B_WORD2_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB58_8B_WORD0,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB5_64B_WORD14_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x428++0x7 line.long 0x0 "WORD058,Message Buffer 58 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB17_16B_WORD3_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB58_8B_WORD1,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB5_64B_WORD15_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x7 line.long 0x0 "WORD158,Message Buffer 58 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS59,Message Buffer 59 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB10_32B_WORD6_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x430++0x3 line.long 0x0 "MB18_16B_CS_H,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB59_8B_CS,Message Buffer 59 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x7 line.long 0x0 "MB6_64B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID59,Message Buffer 59 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB10_32B_WORD7_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x434++0x3 line.long 0x0 "MB18_16B_ID_H,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB59_8B_ID,Message Buffer 59 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x7 line.long 0x0 "MB6_64B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x438++0x3 line.long 0x0 "MB18_16B_WORD0_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB59_8B_WORD0,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB6_64B_WORD0_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x7 line.long 0x0 "WORD059,Message Buffer 59 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x43C++0x3 line.long 0x0 "MB18_16B_WORD1_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB59_8B_WORD1,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB6_64B_WORD1_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x7 line.long 0x0 "WORD159,Message Buffer 59 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS60,Message Buffer 60 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x3 line.long 0x0 "MB11_32B_WORD0_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB18_16B_WORD2_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB60_8B_CS,Message Buffer 60 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x7 line.long 0x0 "MB6_64B_WORD2_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID60,Message Buffer 60 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x3 line.long 0x0 "MB11_32B_WORD1_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB18_16B_WORD3_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB60_8B_ID,Message Buffer 60 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x7 line.long 0x0 "MB6_64B_WORD3_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB19_16B_CS_H,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x448++0x3 line.long 0x0 "MB60_8B_WORD0,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB6_64B_WORD4_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x448++0x7 line.long 0x0 "WORD060,Message Buffer 60 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB19_16B_ID_H,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x44C++0x3 line.long 0x0 "MB60_8B_WORD1,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB6_64B_WORD5_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x7 line.long 0x0 "WORD160,Message Buffer 60 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS61,Message Buffer 61 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x3 line.long 0x0 "MB11_32B_WORD4_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB19_16B_WORD0_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB61_8B_CS,Message Buffer 61 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x7 line.long 0x0 "MB6_64B_WORD6_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID61,Message Buffer 61 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x3 line.long 0x0 "MB11_32B_WORD5_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB19_16B_WORD1_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB61_8B_ID,Message Buffer 61 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x7 line.long 0x0 "MB6_64B_WORD7_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB19_16B_WORD2_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB61_8B_WORD0,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB6_64B_WORD8_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x458++0x7 line.long 0x0 "WORD061,Message Buffer 61 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB19_16B_WORD3_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB61_8B_WORD1,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB6_64B_WORD9_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x7 line.long 0x0 "WORD161,Message Buffer 61 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS62,Message Buffer 62 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB20_16B_CS_H,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB62_8B_CS,Message Buffer 62 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x7 line.long 0x0 "MB6_64B_WORD10_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID62,Message Buffer 62 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB20_16B_ID_H,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB62_8B_ID,Message Buffer 62 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x7 line.long 0x0 "MB6_64B_WORD11_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB62_8B_WORD0,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB6_64B_WORD12_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x468++0x7 line.long 0x0 "WORD062,Message Buffer 62 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB62_8B_WORD1,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB6_64B_WORD13_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x7 line.long 0x0 "WORD162,Message Buffer 62 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS63,Message Buffer 63 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x3 line.long 0x0 "MB20_16B_WORD2_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x470++0x3 line.long 0x0 "MB63_8B_CS,Message Buffer 63 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x7 line.long 0x0 "MB6_64B_WORD14_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID63,Message Buffer 63 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x3 line.long 0x0 "MB20_16B_WORD3_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x474++0x3 line.long 0x0 "MB63_8B_ID,Message Buffer 63 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x7 line.long 0x0 "MB6_64B_WORD15_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD0,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x478++0x7 line.long 0x0 "WORD063,Message Buffer 63 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD1,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x47C++0x3 line.long 0x0 "WORD163,Message Buffer 63 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." repeat 64. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x880)++0x3 line.long 0x0 "RXIMR[$1],Rx Individual Mask registers" hexmask.long 0x0 0.--31. 1. "MI,Individual Mask Bits" repeat.end group.long 0xAE0++0xF line.long 0x0 "MECR,Memory Error Control register" bitfld.long 0x0 31. "ECRWRDIS,Error Configuration Register Write Disable" "0: Write is enabled.,1: Write is disabled." bitfld.long 0x0 19. "HANCEI_MSK,Host Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 18. "FANCEI_MSK,FlexCAN Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 16. "CEI_MSK,Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 15. "HAERRIE,Host Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." bitfld.long 0x0 14. "FAERRIE,FlexCAN Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." newline bitfld.long 0x0 13. "EXTERRIE,Extended Error Injection Enable" "0: Error injection is applied only to the 32-bit..,1: Error injection is applied to the 64-bit word." bitfld.long 0x0 9. "RERRDIS,Error Report Disable" "0: Enable updates of the error report registers.,1: Disable updates of the error report registers." newline bitfld.long 0x0 8. "ECCDIS,Error Correction Disable" "0: Enable memory error correction.,1: Disable memory error correction." bitfld.long 0x0 7. "NCEFAFRZ,Non-Correctable Errors In FlexCAN Access Put Device In Freeze Mode" "0: Keep normal operation.,1: Put FlexCAN in Freeze mode (see section 'Freeze.." line.long 0x4 "ERRIAR,Error Injection Address register" hexmask.long.word 0x4 2.--13. 1. "INJADDR_H,Error Injection Address High" rbitfld.long 0x4 0.--1. "INJADDR_L,Error Injection Address Low" "0,1,2,3" line.long 0x8 "ERRIDPR,Error Injection Data Pattern register" hexmask.long 0x8 0.--31. 1. "DFLIP,Data flip pattern" line.long 0xC "ERRIPPR,Error Injection Parity Pattern register" hexmask.long.byte 0xC 24.--28. 1. "PFLIP3,Parity Flip Pattern For Byte 3 (most significant)" hexmask.long.byte 0xC 16.--20. 1. "PFLIP2,Parity Flip Pattern For Byte 2" newline hexmask.long.byte 0xC 8.--12. 1. "PFLIP1,Parity Flip Pattern For Byte 1" hexmask.long.byte 0xC 0.--4. 1. "PFLIP0,Parity Flip Pattern For Byte 0 (Least Significant)" rgroup.long 0xAF0++0xB line.long 0x0 "RERRAR,Error Report Address register" bitfld.long 0x0 24. "NCE,Non-Correctable Error" "0: Reporting a correctable error,1: Reporting a non-correctable error" bitfld.long 0x0 16.--18. "SAID,SAID" "0,1,2,3,4,5,6,7" newline hexmask.long.word 0x0 0.--13. 1. "ERRADDR,Address Where Error Detected" line.long 0x4 "RERRDR,Error Report Data register" hexmask.long 0x4 0.--31. 1. "RDATA,Raw data word read from memory with error" line.long 0x8 "RERRSYNR,Error Report Syndrome register" bitfld.long 0x8 31. "BE3,Byte Enabled For Byte 3 (most significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 24.--28. 1. "SYND3,Error Syndrome For Byte 3 (most significant)" newline bitfld.long 0x8 23. "BE2,Byte Enabled For Byte 2" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 16.--20. 1. "SYND2,Error Syndrome For Byte 2" newline bitfld.long 0x8 15. "BE1,Byte Enabled For Byte 1" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 8.--12. 1. "SYND1,Error Syndrome for Byte 1" newline bitfld.long 0x8 7. "BE0,Byte Enabled For Byte 0 (least significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 0.--4. 1. "SYND0,Error Syndrome For Byte 0 (least significant)" group.long 0xAFC++0x3 line.long 0x0 "ERRSR,Error Status register" eventfld.long 0x0 19. "HANCEIF,Host Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in host..,1: A non-correctable error was detected in a host.." eventfld.long 0x0 18. "FANCEIF,FlexCAN Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in..,1: A non-correctable error was detected in a.." newline eventfld.long 0x0 16. "CEIF,Correctable Error Interrupt Flag" "0: No correctable errors were detected so far.,1: A correctable error was detected." eventfld.long 0x0 3. "HANCEIOF,Host Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in host..,1: Overrun on non-correctable errors in host access" newline eventfld.long 0x0 2. "FANCEIOF,FlexCAN Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in FlexCAN..,1: Overrun on non-correctable errors in FlexCAN.." eventfld.long 0x0 0. "CEIOF,Correctable Error Interrupt Overrun Flag" "0: No overrun on correctable errors,1: Overrun on correctable errors" group.long 0xC00++0x7 line.long 0x0 "FDCTRL,CAN FD Control register" bitfld.long 0x0 31. "FDRATE,Bit Rate Switch Enable" "0: Transmit a frame in nominal rate. The BRS bit in..,1: Transmit a frame with bit rate switching if the.." bitfld.long 0x0 19.--20. "MBDSR1,Message Buffer Data Size for Region 1" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." newline bitfld.long 0x0 16.--17. "MBDSR0,Message Buffer Data Size for Region 0" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." bitfld.long 0x0 15. "TDCEN,Transceiver Delay Compensation Enable" "0: TDC is disabled,1: TDC is enabled" newline eventfld.long 0x0 14. "TDCFAIL,Transceiver Delay Compensation Fail" "0: Measured loop delay is in range.,1: Measured loop delay is out of range." hexmask.long.byte 0x0 8.--12. 1. "TDCOFF,Transceiver Delay Compensation Offset" newline hexmask.long.byte 0x0 0.--5. 1. "TDCVAL,Transceiver Delay Compensation Value" line.long 0x4 "FDCBT,CAN FD Bit Timing register" hexmask.long.word 0x4 20.--29. 1. "FPRESDIV,Fast Prescaler Division Factor" bitfld.long 0x4 16.--18. "FRJW,Fast Resync Jump Width" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 10.--14. 1. "FPROPSEG,Fast Propagation Segment" bitfld.long 0x4 5.--7. "FPSEG1,Fast Phase Segment 1" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "FPSEG2,Fast Phase Segment 2" "0,1,2,3,4,5,6,7" rgroup.long 0xC08++0x3 line.long 0x0 "FDCRC,CAN FD CRC register" hexmask.long.byte 0x0 24.--30. 1. "FD_MBCRC,CRC Mailbox Number for FD_TXCRC" hexmask.long.tbyte 0x0 0.--20. 1. "FD_TXCRC,Extended Transmitted CRC value" tree.end tree "CAN3" base ad:0x40C3C000 group.long 0x0++0xB line.long 0x0 "MCR,Module Configuration register" bitfld.long 0x0 31. "MDIS,Module Disable" "0: Enable the FlexCAN module.,1: Disable the FlexCAN module." bitfld.long 0x0 30. "FRZ,Freeze Enable" "0: Not enabled to enter Freeze mode.,1: Enabled to enter Freeze mode." newline bitfld.long 0x0 29. "RFEN,Rx FIFO Enable" "0: Rx FIFO not enabled.,1: Rx FIFO enabled." bitfld.long 0x0 28. "HALT,Halt FlexCAN" "0: No Freeze mode request.,1: Enters Freeze mode if the FRZ bit is asserted." newline rbitfld.long 0x0 27. "NOTRDY,FlexCAN Not Ready" "0: FlexCAN module is either in Normal mode..,1: FlexCAN module is either in Disable mode Doze.." bitfld.long 0x0 26. "WAKMSK,Wake Up Interrupt Mask" "0: Wake Up interrupt is disabled.,1: Wake Up interrupt is enabled." newline bitfld.long 0x0 25. "SOFTRST,Soft Reset" "0: No reset request.,1: Resets the registers affected by soft reset." rbitfld.long 0x0 24. "FRZACK,Freeze Mode Acknowledge" "0: FlexCAN not in Freeze mode prescaler running.,1: FlexCAN in Freeze mode prescaler stopped." newline bitfld.long 0x0 23. "SUPV,Supervisor Mode" "0: FlexCAN is in User mode. Affected registers..,1: FlexCAN is in Supervisor mode. Affected.." bitfld.long 0x0 22. "SLFWAK,Self Wake Up" "0: FlexCAN Self Wake Up feature is disabled.,1: FlexCAN Self Wake Up feature is enabled." newline bitfld.long 0x0 21. "WRNEN,Warning Interrupt Enable" "0: TWRNINT and RWRNINT bits are zero independent of..,1: TWRNINT and RWRNINT bits are set when the.." rbitfld.long 0x0 20. "LPMACK,Low-Power Mode Acknowledge" "0: FlexCAN is not in a low-power mode.,1: FlexCAN is in a low-power mode." newline bitfld.long 0x0 19. "WAKSRC,Wake Up Source" "0: FlexCAN uses the unfiltered Rx input to detect..,1: FlexCAN uses the filtered Rx input to detect.." bitfld.long 0x0 18. "DOZE,Doze Mode Enable" "0: FlexCAN is not enabled to enter low-power mode..,1: FlexCAN is enabled to enter low-power mode when.." newline bitfld.long 0x0 17. "SRXDIS,Self Reception Disable" "0: Self-reception enabled.,1: Self-reception disabled." bitfld.long 0x0 16. "IRMQ,Individual Rx Masking And Queue Enable" "0: Individual Rx masking and queue feature are..,1: Individual Rx masking and queue feature are.." newline bitfld.long 0x0 15. "DMA,DMA Enable" "0: DMA feature for RX FIFO disabled.,1: DMA feature for RX FIFO enabled." bitfld.long 0x0 13. "LPRIOEN,Local Priority Enable" "0: Local Priority disabled.,1: Local Priority enabled." newline bitfld.long 0x0 12. "AEN,Abort Enable" "0: Abort disabled.,1: Abort enabled." bitfld.long 0x0 11. "FDEN,CAN FD operation enable" "0: CAN FD is disabled. FlexCAN is able to receive..,1: CAN FD is enabled. FlexCAN is able to receive.." newline bitfld.long 0x0 8.--9. "IDAM,ID Acceptance Mode" "0: Format A: One full ID (standard and extended)..,1: Format B: Two full standard IDs or two partial..,2: Format C: Four partial 8-bit standard IDs per ID..,3: Format D: All frames rejected." hexmask.long.byte 0x0 0.--6. 1. "MAXMB,Number Of The Last Message Buffer" line.long 0x4 "CTRL1,Control 1 register" hexmask.long.byte 0x4 24.--31. 1. "PRESDIV,Prescaler Division Factor" bitfld.long 0x4 22.--23. "RJW,Resync Jump Width" "0,1,2,3" newline bitfld.long 0x4 19.--21. "PSEG1,Phase Segment 1" "0,1,2,3,4,5,6,7" bitfld.long 0x4 16.--18. "PSEG2,Phase Segment 2" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 15. "BOFFMSK,Bus Off Interrupt Mask" "0: Bus Off interrupt disabled.,1: Bus Off interrupt enabled." bitfld.long 0x4 14. "ERRMSK,Error Interrupt Mask" "0: Error interrupt disabled.,1: Error interrupt enabled." newline bitfld.long 0x4 13. "CLKSRC,CAN Engine Clock Source" "0: The CAN engine clock source is the oscillator..,1: The CAN engine clock source is the peripheral.." bitfld.long 0x4 12. "LPB,Loop Back Mode" "0: Loop Back disabled.,1: Loop Back enabled." newline bitfld.long 0x4 11. "TWRNMSK,Tx Warning Interrupt Mask" "0: Tx Warning interrupt disabled.,1: Tx Warning interrupt enabled." bitfld.long 0x4 10. "RWRNMSK,Rx Warning Interrupt Mask" "0: Rx Warning interrupt disabled.,1: Rx Warning interrupt enabled." newline bitfld.long 0x4 7. "SMP,CAN Bit Sampling" "0: Just one sample is used to determine the bit..,1: Three samples are used to determine the value of.." bitfld.long 0x4 6. "BOFFREC,Bus Off Recovery" "0: Automatic recovering from Bus Off state enabled.,1: Automatic recovering from Bus Off state disabled." newline bitfld.long 0x4 5. "TSYN,Timer Sync" "0: Timer sync feature disabled,1: Timer sync feature enabled" bitfld.long 0x4 4. "LBUF,Lowest Buffer Transmitted First" "0: Buffer with highest priority is transmitted first.,1: Lowest number buffer is transmitted first." newline bitfld.long 0x4 3. "LOM,Listen-Only Mode" "0: Listen-Only mode is deactivated.,1: FlexCAN module operates in Listen-Only mode." bitfld.long 0x4 0.--2. "PROPSEG,Propagation Segment" "0,1,2,3,4,5,6,7" line.long 0x8 "TIMER,Free Running Timer" hexmask.long.word 0x8 0.--15. 1. "TIMER,Timer Value" group.long 0x10++0x27 line.long 0x0 "RXMGMASK,Rx Mailboxes Global Mask register" hexmask.long 0x0 0.--31. 1. "MG,Rx Mailboxes Global Mask Bits" line.long 0x4 "RX14MASK,Rx 14 Mask register" hexmask.long 0x4 0.--31. 1. "RX14M,Rx Buffer 14 Mask Bits" line.long 0x8 "RX15MASK,Rx 15 Mask register" hexmask.long 0x8 0.--31. 1. "RX15M,Rx Buffer 15 Mask Bits" line.long 0xC "ECR,Error Counter" hexmask.long.byte 0xC 24.--31. 1. "RXERRCNT_FAST,Receive Error Counter for fast bits" hexmask.long.byte 0xC 16.--23. 1. "TXERRCNT_FAST,Transmit Error Counter for fast bits" newline hexmask.long.byte 0xC 8.--15. 1. "RXERRCNT,Receive Error Counter" hexmask.long.byte 0xC 0.--7. 1. "TXERRCNT,Transmit Error Counter" line.long 0x10 "ESR1,Error and Status 1 register" rbitfld.long 0x10 31. "BIT1ERR_FAST,Bit1 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as recessive is received.." rbitfld.long 0x10 30. "BIT0ERR_FAST,Bit0 Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." newline rbitfld.long 0x10 28. "CRCERR_FAST,Cyclic Redundancy Check Error in the CRC field of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 27. "FRMERR_FAST,Form Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A form error occurred since last read of this.." newline rbitfld.long 0x10 26. "STFERR_FAST,Stuffing Error in the Data Phase of CAN FD frames with the BRS bit set" "0: No such occurrence.,1: A stuffing error occurred since last read of.." eventfld.long 0x10 21. "ERROVR,Error Overrun" "0: Overrun has not occurred.,1: Overrun has occurred." newline eventfld.long 0x10 20. "ERRINT_FAST,Error interrupt for errors detected in Data Phase of CAN FD frames with BRS bit set" "0: No such occurrence.,1: Indicates setting of any error bit detected in.." eventfld.long 0x10 19. "BOFFDONEINT,Bus Off Done Interrupt" "0: No such occurrence.,1: FlexCAN module has completed Bus Off process." newline rbitfld.long 0x10 18. "SYNCH,CAN Synchronization Status" "0: FlexCAN is not synchronized to the CAN bus.,1: FlexCAN is synchronized to the CAN bus." eventfld.long 0x10 17. "TWRNINT,Tx Warning Interrupt Flag" "0: No such occurrence.,1: The Tx error counter transitioned from less than.." newline eventfld.long 0x10 16. "RWRNINT,Rx Warning Interrupt Flag" "0: No such occurrence.,1: The Rx error counter transitioned from less than.." rbitfld.long 0x10 15. "BIT1ERR,Bit1 Error" "0: No such occurrence.,1: At least one bit sent as recessive is received.." newline rbitfld.long 0x10 14. "BIT0ERR,Bit0 Error" "0: No such occurrence.,1: At least one bit sent as dominant is received as.." rbitfld.long 0x10 13. "ACKERR,Acknowledge Error" "0: No such occurrence.,1: An ACK error occurred since last read of this.." newline rbitfld.long 0x10 12. "CRCERR,Cyclic Redundancy Check Error" "0: No such occurrence.,1: A CRC error occurred since last read of this.." rbitfld.long 0x10 11. "FRMERR,Form Error" "0: No such occurrence.,1: A Form Error occurred since last read of this.." newline rbitfld.long 0x10 10. "STFERR,Stuffing Error" "0: No such occurrence.,1: A stuffing error occurred since last read of.." rbitfld.long 0x10 9. "TXWRN,TX Error Warning" "0: No such occurrence.,1: TXERRCNT is greater than or equal to 96." newline rbitfld.long 0x10 8. "RXWRN,Rx Error Warning" "0: No such occurrence.,1: RXERRCNT is greater than or equal to 96." rbitfld.long 0x10 7. "IDLE,IDLE" "0: No such occurrence.,1: CAN bus is now IDLE." newline rbitfld.long 0x10 6. "TX,FlexCAN In Transmission" "0: FlexCAN is not transmitting a message.,1: FlexCAN is transmitting a message." rbitfld.long 0x10 4.--5. "FLTCONF,Fault Confinement State" "0: Bus Off,1: Error Passive,2: Bus Off,3: Bus Off" newline rbitfld.long 0x10 3. "RX,FlexCAN In Reception" "0: FlexCAN is not receiving a message.,1: FlexCAN is receiving a message." eventfld.long 0x10 2. "BOFFINT,Bus Off Interrupt" "0: No such occurrence.,1: FlexCAN module entered Bus Off state." newline eventfld.long 0x10 1. "ERRINT,Error Interrupt" "0: No such occurrence.,1: Indicates setting of any error bit in the Error.." eventfld.long 0x10 0. "WAKINT,Wake-Up Interrupt" "0: No such occurrence.,1: Indicates a recessive to dominant transition was.." line.long 0x14 "IMASK2,Interrupt Masks 2 register" hexmask.long 0x14 0.--31. 1. "BUF63TO32M,Buffer MBi Mask" line.long 0x18 "IMASK1,Interrupt Masks 1 register" hexmask.long 0x18 0.--31. 1. "BUF31TO0M,Buffer MBi Mask" line.long 0x1C "IFLAG2,Interrupt Flags 2 register" hexmask.long 0x1C 0.--31. 1. "BUF63TO32I,Buffer MBi Interrupt" line.long 0x20 "IFLAG1,Interrupt Flags 1 register" hexmask.long.tbyte 0x20 8.--31. 1. "BUF31TO8I,Buffer MBi Interrupt" eventfld.long 0x20 7. "BUF7I,Buffer MB7 Interrupt Or Rx FIFO Overflow" "0: No occurrence of MB7 completing..,1: MB7 completed transmission/reception when.." newline eventfld.long 0x20 6. "BUF6I,Buffer MB6 Interrupt Or Rx FIFO Warning" "0: No occurrence of MB6 completing..,1: MB6 completed transmission/reception when.." eventfld.long 0x20 5. "BUF5I,Buffer MB5 Interrupt Or Frames available in Rx FIFO" "0: No occurrence of MB5 completing..,1: MB5 completed transmission/reception when.." newline hexmask.long.byte 0x20 1.--4. 1. "BUF4TO1I,Buffer MBi Interrupt Or Reserved" eventfld.long 0x20 0. "BUF0I,Buffer MB0 Interrupt Or Clear FIFO bit" "0: The corresponding buffer has no occurrence of..,1: The corresponding buffer has successfully.." line.long 0x24 "CTRL2,Control 2 register" bitfld.long 0x24 31. "ERRMSK_FAST,Error Interrupt Mask for errors detected in the data phase of fast CAN FD frames" "0: ERRINT_FAST error interrupt disabled.,1: ERRINT_FAST error interrupt enabled." bitfld.long 0x24 30. "BOFFDONEMSK,Bus Off Done Interrupt Mask" "0: Bus off done interrupt disabled.,1: Bus off done interrupt enabled." newline bitfld.long 0x24 29. "ECRWRE,Error-correction Configuration Register Write Enable" "0: Disable update.,1: Enable update." bitfld.long 0x24 28. "WRMFRZ,Write-Access To Memory In Freeze Mode" "0: Maintain the write access restrictions.,1: Enable unrestricted write access to FlexCAN.." newline hexmask.long.byte 0x24 24.--27. 1. "RFFN,Number Of Rx FIFO Filters" hexmask.long.byte 0x24 19.--23. 1. "TASD,Tx Arbitration Start Delay" newline bitfld.long 0x24 18. "MRP,Mailboxes Reception Priority" "0: Matching starts from Rx FIFO and continues on..,1: Matching starts from mailboxes and continues on.." bitfld.long 0x24 17. "RRS,Remote Request Storing" "0: Remote response frame is generated.,1: Remote request frame is stored." newline bitfld.long 0x24 16. "EACEN,Entire Frame Arbitration Field Comparison Enable For Rx Mailboxes" "0: Rx mailbox filter's IDE bit is always compared..,1: Enables the comparison of both Rx mailbox.." bitfld.long 0x24 15. "TIMER_SRC,Timer Source" "0: The free running timer is clocked by the CAN bit..,1: The free running timer is clocked by an external.." newline bitfld.long 0x24 14. "PREXCEN,Protocol Exception Enable" "0: Protocol exception is disabled.,1: Protocol exception is enabled." bitfld.long 0x24 12. "ISOCANFDEN,ISO CAN FD Enable" "0: FlexCAN operates using the non-ISO CAN FD..,1: FlexCAN operates using the ISO CAN FD protocol.." newline bitfld.long 0x24 11. "EDFLTDIS,Edge Filter Disable" "0: Edge filter is enabled,1: Edge filter is disabled" rgroup.long 0x38++0x3 line.long 0x0 "ESR2,Error and Status 2 register" hexmask.long.byte 0x0 16.--22. 1. "LPTM,Lowest Priority Tx Mailbox" bitfld.long 0x0 14. "VPS,Valid Priority Status" "0: Contents of IMB and LPTM are invalid.,1: Contents of IMB and LPTM are valid." newline bitfld.long 0x0 13. "IMB,Inactive Mailbox" "0: If ESR2[VPS] is asserted the ESR2[LPTM] is not..,1: If ESR2[VPS] is asserted there is at least one.." rgroup.long 0x44++0x3 line.long 0x0 "CRCR,CRC register" hexmask.long.byte 0x0 16.--22. 1. "MBCRC,CRC Mailbox" hexmask.long.word 0x0 0.--14. 1. "TXCRC,Transmitted CRC value" group.long 0x48++0x3 line.long 0x0 "RXFGMASK,Rx FIFO Global Mask register" hexmask.long 0x0 0.--31. 1. "FGM,Rx FIFO Global Mask Bits" rgroup.long 0x4C++0x3 line.long 0x0 "RXFIR,Rx FIFO Information register" hexmask.long.word 0x0 0.--8. 1. "IDHIT,Identifier Acceptance Filter Hit Indicator" group.long 0x50++0x3 line.long 0x0 "CBT,CAN Bit Timing register" bitfld.long 0x0 31. "BTF,Bit Timing Format Enable" "0: Extended bit time definitions disabled.,1: Extended bit time definitions enabled." hexmask.long.word 0x0 21.--30. 1. "EPRESDIV,Extended Prescaler Division Factor" newline hexmask.long.byte 0x0 16.--20. 1. "ERJW,Extended Resync Jump Width" hexmask.long.byte 0x0 10.--15. 1. "EPROPSEG,Extended Propagation Segment" newline hexmask.long.byte 0x0 5.--9. 1. "EPSEG1,Extended Phase Segment 1" hexmask.long.byte 0x0 0.--4. 1. "EPSEG2,Extended Phase Segment 2" group.long 0x80++0x3 line.long 0x0 "CS0,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_16B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_32B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x3 line.long 0x0 "MB0_64B_CS_L,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x80++0x7 line.long 0x0 "MB0_8B_CS,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID0,Message Buffer 0 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_16B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_32B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x3 line.long 0x0 "MB0_64B_ID_L,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x84++0x7 line.long 0x0 "MB0_8B_ID,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_32B_WORD0_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_64B_WORD0_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x3 line.long 0x0 "MB0_8B_WORD0,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x88++0x7 line.long 0x0 "WORD00,Message Buffer 0 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_32B_WORD1_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_64B_WORD1_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x3 line.long 0x0 "MB0_8B_WORD1,Message Buffer 0 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x8C++0x7 line.long 0x0 "WORD10,Message Buffer 0 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS1,Message Buffer 1 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x90++0x3 line.long 0x0 "MB0_16B_WORD2_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_32B_WORD2_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x3 line.long 0x0 "MB0_64B_WORD2_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x90++0x7 line.long 0x0 "MB1_8B_CS,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID1,Message Buffer 1 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x94++0x3 line.long 0x0 "MB0_16B_WORD3_L,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_32B_WORD3_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x3 line.long 0x0 "MB0_64B_WORD3_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x94++0x7 line.long 0x0 "MB1_8B_ID,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB0_64B_WORD4_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x98++0x3 line.long 0x0 "MB1_16B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x98++0x3 line.long 0x0 "MB1_8B_WORD0,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x98++0x7 line.long 0x0 "WORD01,Message Buffer 1 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB0_64B_WORD5_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x3 line.long 0x0 "MB1_16B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x9C++0x3 line.long 0x0 "MB1_8B_WORD1,Message Buffer 1 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x9C++0x7 line.long 0x0 "WORD11,Message Buffer 1 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS2,Message Buffer 2 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA0++0x3 line.long 0x0 "MB0_32B_WORD6_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB0_64B_WORD6_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x3 line.long 0x0 "MB1_16B_WORD0_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA0++0x7 line.long 0x0 "MB2_8B_CS,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID2,Message Buffer 2 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xA4++0x3 line.long 0x0 "MB0_32B_WORD7_L,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB0_64B_WORD7_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x3 line.long 0x0 "MB1_16B_WORD1_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xA4++0x7 line.long 0x0 "MB2_8B_ID,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_16B_WORD2_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x3 line.long 0x0 "MB1_32B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xA8++0x3 line.long 0x0 "MB2_8B_WORD0,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xA8++0x7 line.long 0x0 "WORD02,Message Buffer 2 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_16B_WORD3_L,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x3 line.long 0x0 "MB1_32B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xAC++0x3 line.long 0x0 "MB2_8B_WORD1,Message Buffer 2 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xAC++0x7 line.long 0x0 "WORD12,Message Buffer 2 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS3,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x3 line.long 0x0 "MB0_64B_WORD10_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB1_32B_WORD0_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB0++0x3 line.long 0x0 "MB2_16B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xB0++0x7 line.long 0x0 "MB3_8B_CS,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID3,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x3 line.long 0x0 "MB0_64B_WORD11_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB1_32B_WORD1_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xB4++0x3 line.long 0x0 "MB2_16B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xB4++0x7 line.long 0x0 "MB3_8B_ID,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB1_32B_WORD2_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB2_16B_WORD0_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x3 line.long 0x0 "MB3_8B_WORD0,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xB8++0x7 line.long 0x0 "WORD03,Message Buffer 3 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB1_32B_WORD3_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB2_16B_WORD1_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x3 line.long 0x0 "MB3_8B_WORD1,Message Buffer 3 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xBC++0x7 line.long 0x0 "WORD13,Message Buffer 3 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS4,Message Buffer 4 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC0++0x3 line.long 0x0 "MB0_64B_WORD14_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB1_32B_WORD4_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x3 line.long 0x0 "MB2_16B_WORD2_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xC0++0x7 line.long 0x0 "MB4_8B_CS,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID4,Message Buffer 4 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xC4++0x3 line.long 0x0 "MB0_64B_WORD15_L,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB1_32B_WORD5_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x3 line.long 0x0 "MB2_16B_WORD3_L,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xC4++0x7 line.long 0x0 "MB4_8B_ID,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x3 line.long 0x0 "MB1_64B_CS_L,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB3_16B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xC8++0x3 line.long 0x0 "MB4_8B_WORD0,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xC8++0x7 line.long 0x0 "WORD04,Message Buffer 4 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_L,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x3 line.long 0x0 "MB1_64B_ID_L,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB3_16B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xCC++0x3 line.long 0x0 "MB4_8B_WORD1,Message Buffer 4 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xCC++0x7 line.long 0x0 "WORD14,Message Buffer 4 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS5,Message Buffer 5 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB1_64B_WORD0_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x3 line.long 0x0 "MB2_32B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xD0++0x3 line.long 0x0 "MB3_16B_WORD0_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD0++0x7 line.long 0x0 "MB5_8B_CS,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID5,Message Buffer 5 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB1_64B_WORD1_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x3 line.long 0x0 "MB2_32B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xD4++0x3 line.long 0x0 "MB3_16B_WORD1_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xD4++0x7 line.long 0x0 "MB5_8B_ID,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD2_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB2_32B_WORD0_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB3_16B_WORD2_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x3 line.long 0x0 "MB5_8B_WORD0,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xD8++0x7 line.long 0x0 "WORD05,Message Buffer 5 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB2_32B_WORD1_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB3_16B_WORD3_L,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x3 line.long 0x0 "MB5_8B_WORD1,Message Buffer 5 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xDC++0x7 line.long 0x0 "WORD15,Message Buffer 5 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS6,Message Buffer 6 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x3 line.long 0x0 "MB1_64B_WORD4_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB2_32B_WORD2_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xE0++0x3 line.long 0x0 "MB4_16B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xE0++0x7 line.long 0x0 "MB6_8B_CS,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID6,Message Buffer 6 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x3 line.long 0x0 "MB1_64B_WORD5_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB2_32B_WORD3_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xE4++0x3 line.long 0x0 "MB4_16B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xE4++0x7 line.long 0x0 "MB6_8B_ID,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB2_32B_WORD4_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB4_16B_WORD0_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x3 line.long 0x0 "MB6_8B_WORD0,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xE8++0x7 line.long 0x0 "WORD06,Message Buffer 6 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB2_32B_WORD5_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB4_16B_WORD1_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x3 line.long 0x0 "MB6_8B_WORD1,Message Buffer 6 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xEC++0x7 line.long 0x0 "WORD16,Message Buffer 6 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS7,Message Buffer 7 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF0++0x3 line.long 0x0 "MB1_64B_WORD8_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB2_32B_WORD6_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x3 line.long 0x0 "MB4_16B_WORD2_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0xF0++0x7 line.long 0x0 "MB7_8B_CS,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID7,Message Buffer 7 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xF4++0x3 line.long 0x0 "MB1_64B_WORD9_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB2_32B_WORD7_L,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x3 line.long 0x0 "MB4_16B_WORD3_L,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0xF4++0x7 line.long 0x0 "MB7_8B_ID,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD10_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x3 line.long 0x0 "MB3_32B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB5_16B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0xF8++0x3 line.long 0x0 "MB7_8B_WORD0,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0xF8++0x7 line.long 0x0 "WORD07,Message Buffer 7 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x3 line.long 0x0 "MB3_32B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB5_16B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0xFC++0x3 line.long 0x0 "MB7_8B_WORD1,Message Buffer 7 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0xFC++0x7 line.long 0x0 "WORD17,Message Buffer 7 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS8,Message Buffer 8 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x100++0x3 line.long 0x0 "MB1_64B_WORD12_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB3_32B_WORD0_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x3 line.long 0x0 "MB5_16B_WORD0_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x100++0x7 line.long 0x0 "MB8_8B_CS,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID8,Message Buffer 8 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x104++0x3 line.long 0x0 "MB1_64B_WORD13_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB3_32B_WORD1_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x3 line.long 0x0 "MB5_16B_WORD1_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x104++0x7 line.long 0x0 "MB8_8B_ID,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD14_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB3_32B_WORD2_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB5_16B_WORD2_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x108++0x3 line.long 0x0 "MB8_8B_WORD0,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x108++0x7 line.long 0x0 "WORD08,Message Buffer 8 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_L,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB3_32B_WORD3_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB5_16B_WORD3_L,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x3 line.long 0x0 "MB8_8B_WORD1,Message Buffer 8 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x10C++0x7 line.long 0x0 "WORD18,Message Buffer 8 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS9,Message Buffer 9 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB2_64B_CS_L,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x3 line.long 0x0 "MB3_32B_WORD4_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x110++0x3 line.long 0x0 "MB6_16B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x110++0x7 line.long 0x0 "MB9_8B_CS,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID9,Message Buffer 9 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB2_64B_ID_L,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x3 line.long 0x0 "MB3_32B_WORD5_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x114++0x3 line.long 0x0 "MB6_16B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x114++0x7 line.long 0x0 "MB9_8B_ID,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB3_32B_WORD6_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB6_16B_WORD0_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x3 line.long 0x0 "MB9_8B_WORD0,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x118++0x7 line.long 0x0 "WORD09,Message Buffer 9 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB3_32B_WORD7_L,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB6_16B_WORD1_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x3 line.long 0x0 "MB9_8B_WORD1,Message Buffer 9 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x11C++0x7 line.long 0x0 "WORD19,Message Buffer 9 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS10,Message Buffer 10 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB10_8B_CS,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x3 line.long 0x0 "MB2_64B_WORD2_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x120++0x3 line.long 0x0 "MB4_32B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x120++0x7 line.long 0x0 "MB6_16B_WORD2_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID10,Message Buffer 10 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB10_8B_ID,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x3 line.long 0x0 "MB2_64B_WORD3_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x124++0x3 line.long 0x0 "MB4_32B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x124++0x7 line.long 0x0 "MB6_16B_WORD3_L,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD0,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB2_64B_WORD4_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB4_32B_WORD0_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x128++0x3 line.long 0x0 "MB7_16B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x128++0x7 line.long 0x0 "WORD010,Message Buffer 10 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_8B_WORD1,Message Buffer 10 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB2_64B_WORD5_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB4_32B_WORD1_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x12C++0x3 line.long 0x0 "MB7_16B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x12C++0x7 line.long 0x0 "WORD110,Message Buffer 10 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS11,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB11_8B_CS,Message Buffer 11 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x130++0x3 line.long 0x0 "MB2_64B_WORD6_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x130++0x3 line.long 0x0 "MB4_32B_WORD2_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x130++0x7 line.long 0x0 "MB7_16B_WORD0_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID11,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB11_8B_ID,Message Buffer 11 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x134++0x3 line.long 0x0 "MB2_64B_WORD7_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x134++0x3 line.long 0x0 "MB4_32B_WORD3_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x134++0x7 line.long 0x0 "MB7_16B_WORD1_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD0,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB2_64B_WORD8_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB4_32B_WORD4_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x138++0x3 line.long 0x0 "MB7_16B_WORD2_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x138++0x7 line.long 0x0 "WORD011,Message Buffer 11 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_8B_WORD1,Message Buffer 11 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB2_64B_WORD9_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB4_32B_WORD5_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x3 line.long 0x0 "MB7_16B_WORD3_L,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x13C++0x7 line.long 0x0 "WORD111,Message Buffer 11 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS12,Message Buffer 12 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB12_8B_CS,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x140++0x3 line.long 0x0 "MB2_64B_WORD10_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x140++0x3 line.long 0x0 "MB4_32B_WORD6_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x140++0x7 line.long 0x0 "MB8_16B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID12,Message Buffer 12 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB12_8B_ID,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x144++0x3 line.long 0x0 "MB2_64B_WORD11_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x144++0x3 line.long 0x0 "MB4_32B_WORD7_L,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x144++0x7 line.long 0x0 "MB8_16B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB12_8B_WORD0,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB2_64B_WORD12_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x148++0x3 line.long 0x0 "MB5_32B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x148++0x3 line.long 0x0 "MB8_16B_WORD0_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x148++0x7 line.long 0x0 "WORD012,Message Buffer 12 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_8B_WORD1,Message Buffer 12 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB2_64B_WORD13_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x3 line.long 0x0 "MB5_32B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x14C++0x3 line.long 0x0 "MB8_16B_WORD1_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x14C++0x7 line.long 0x0 "WORD112,Message Buffer 12 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS13,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB13_8B_CS,Message Buffer 13 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x150++0x3 line.long 0x0 "MB2_64B_WORD14_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x150++0x3 line.long 0x0 "MB5_32B_WORD0_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x150++0x7 line.long 0x0 "MB8_16B_WORD2_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID13,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB13_8B_ID,Message Buffer 13 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x154++0x3 line.long 0x0 "MB2_64B_WORD15_L,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x154++0x3 line.long 0x0 "MB5_32B_WORD1_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x154++0x7 line.long 0x0 "MB8_16B_WORD3_L,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD0,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB3_64B_CS_L,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x3 line.long 0x0 "MB5_32B_WORD2_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x158++0x3 line.long 0x0 "MB9_16B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x158++0x7 line.long 0x0 "WORD013,Message Buffer 13 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_8B_WORD1,Message Buffer 13 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB3_64B_ID_L,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x3 line.long 0x0 "MB5_32B_WORD3_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x15C++0x3 line.long 0x0 "MB9_16B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x15C++0x7 line.long 0x0 "WORD113,Message Buffer 13 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS14,Message Buffer 14 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB14_8B_CS,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x160++0x3 line.long 0x0 "MB3_64B_WORD0_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x160++0x3 line.long 0x0 "MB5_32B_WORD4_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x160++0x7 line.long 0x0 "MB9_16B_WORD0_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID14,Message Buffer 14 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB14_8B_ID,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x164++0x3 line.long 0x0 "MB3_64B_WORD1_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x164++0x3 line.long 0x0 "MB5_32B_WORD5_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x164++0x7 line.long 0x0 "MB9_16B_WORD1_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD0,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB3_64B_WORD2_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB5_32B_WORD6_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x168++0x3 line.long 0x0 "MB9_16B_WORD2_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x168++0x7 line.long 0x0 "WORD014,Message Buffer 14 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_8B_WORD1,Message Buffer 14 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB3_64B_WORD3_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB5_32B_WORD7_L,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x3 line.long 0x0 "MB9_16B_WORD3_L,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x16C++0x7 line.long 0x0 "WORD114,Message Buffer 14 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS15,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB10_16B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB15_8B_CS,Message Buffer 15 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x170++0x3 line.long 0x0 "MB3_64B_WORD4_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x170++0x7 line.long 0x0 "MB6_32B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID15,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB10_16B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB15_8B_ID,Message Buffer 15 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x174++0x3 line.long 0x0 "MB3_64B_WORD5_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x174++0x7 line.long 0x0 "MB6_32B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB15_8B_WORD0,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB3_64B_WORD6_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x178++0x3 line.long 0x0 "MB6_32B_WORD0_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x178++0x7 line.long 0x0 "WORD015,Message Buffer 15 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB15_8B_WORD1,Message Buffer 15 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB3_64B_WORD7_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x3 line.long 0x0 "MB6_32B_WORD1_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x17C++0x7 line.long 0x0 "WORD115,Message Buffer 15 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS16,Message Buffer 16 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB10_16B_WORD2_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x180++0x3 line.long 0x0 "MB16_8B_CS,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x180++0x3 line.long 0x0 "MB3_64B_WORD8_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x180++0x7 line.long 0x0 "MB6_32B_WORD2_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID16,Message Buffer 16 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB10_16B_WORD3_L,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x184++0x3 line.long 0x0 "MB16_8B_ID,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x184++0x3 line.long 0x0 "MB3_64B_WORD9_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x184++0x7 line.long 0x0 "MB6_32B_WORD3_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x188++0x3 line.long 0x0 "MB16_8B_WORD0,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB3_64B_WORD10_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x188++0x3 line.long 0x0 "MB6_32B_WORD4_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x188++0x7 line.long 0x0 "WORD016,Message Buffer 16 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x18C++0x3 line.long 0x0 "MB16_8B_WORD1,Message Buffer 16 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB3_64B_WORD11_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x3 line.long 0x0 "MB6_32B_WORD5_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x18C++0x7 line.long 0x0 "WORD116,Message Buffer 16 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS17,Message Buffer 17 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB11_16B_WORD0_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x190++0x3 line.long 0x0 "MB17_8B_CS,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x190++0x3 line.long 0x0 "MB3_64B_WORD12_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x190++0x7 line.long 0x0 "MB6_32B_WORD6_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID17,Message Buffer 17 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB11_16B_WORD1_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x194++0x3 line.long 0x0 "MB17_8B_ID,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x194++0x3 line.long 0x0 "MB3_64B_WORD13_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x194++0x7 line.long 0x0 "MB6_32B_WORD7_L,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB17_8B_WORD0,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB3_64B_WORD14_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x198++0x3 line.long 0x0 "MB7_32B_CS_L,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x198++0x7 line.long 0x0 "WORD017,Message Buffer 17 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_L,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB17_8B_WORD1,Message Buffer 17 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB3_64B_WORD15_L,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x19C++0x3 line.long 0x0 "MB7_32B_ID_L,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x19C++0x7 line.long 0x0 "WORD117,Message Buffer 17 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS18,Message Buffer 18 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB12_16B_CS_L,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB18_8B_CS,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x3 line.long 0x0 "MB4_64B_CS_L,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1A0++0x7 line.long 0x0 "MB7_32B_WORD0_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID18,Message Buffer 18 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB12_16B_ID_L,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB18_8B_ID,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x3 line.long 0x0 "MB4_64B_ID_L,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1A4++0x7 line.long 0x0 "MB7_32B_WORD1_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB18_8B_WORD0,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB4_64B_WORD0_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x3 line.long 0x0 "MB7_32B_WORD2_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1A8++0x7 line.long 0x0 "WORD018,Message Buffer 18 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB18_8B_WORD1,Message Buffer 18 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB4_64B_WORD1_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x3 line.long 0x0 "MB7_32B_WORD3_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1AC++0x7 line.long 0x0 "WORD118,Message Buffer 18 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS19,Message Buffer 19 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB12_16B_WORD2_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x3 line.long 0x0 "MB19_8B_CS,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B0++0x3 line.long 0x0 "MB4_64B_WORD2_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1B0++0x7 line.long 0x0 "MB7_32B_WORD4_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID19,Message Buffer 19 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB12_16B_WORD3_L,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x3 line.long 0x0 "MB19_8B_ID,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1B4++0x3 line.long 0x0 "MB4_64B_WORD3_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1B4++0x7 line.long 0x0 "MB7_32B_WORD5_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_L,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1B8++0x3 line.long 0x0 "MB19_8B_WORD0,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB4_64B_WORD4_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x3 line.long 0x0 "MB7_32B_WORD6_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1B8++0x7 line.long 0x0 "WORD019,Message Buffer 19 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_L,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1BC++0x3 line.long 0x0 "MB19_8B_WORD1,Message Buffer 19 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB4_64B_WORD5_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x3 line.long 0x0 "MB7_32B_WORD7_L,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1BC++0x7 line.long 0x0 "WORD119,Message Buffer 19 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS20,Message Buffer 20 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB13_16B_WORD0_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x3 line.long 0x0 "MB20_8B_CS,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1C0++0x3 line.long 0x0 "MB4_64B_WORD6_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x1C0++0x7 line.long 0x0 "MB8_32B_CS_L,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID20,Message Buffer 20 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB13_16B_WORD1_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x3 line.long 0x0 "MB20_8B_ID,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1C4++0x3 line.long 0x0 "MB4_64B_WORD7_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x1C4++0x7 line.long 0x0 "MB8_32B_ID_L,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB20_8B_WORD0,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB4_64B_WORD8_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x3 line.long 0x0 "MB8_32B_WORD0_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1C8++0x7 line.long 0x0 "WORD020,Message Buffer 20 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_L,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB20_8B_WORD1,Message Buffer 20 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB4_64B_WORD9_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x3 line.long 0x0 "MB8_32B_WORD1_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1CC++0x7 line.long 0x0 "WORD120,Message Buffer 20 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS21,Message Buffer 21 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB14_16B_CS_L,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB21_8B_CS,Message Buffer 21 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1D0++0x3 line.long 0x0 "MB4_64B_WORD10_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x1D0++0x7 line.long 0x0 "MB8_32B_WORD2_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID21,Message Buffer 21 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB14_16B_ID_L,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB21_8B_ID,Message Buffer 21 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1D4++0x3 line.long 0x0 "MB4_64B_WORD11_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x1D4++0x7 line.long 0x0 "MB8_32B_WORD3_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB21_8B_WORD0,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB4_64B_WORD12_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x3 line.long 0x0 "MB8_32B_WORD4_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x1D8++0x7 line.long 0x0 "WORD021,Message Buffer 21 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB21_8B_WORD1,Message Buffer 21 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB4_64B_WORD13_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x3 line.long 0x0 "MB8_32B_WORD5_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x1DC++0x7 line.long 0x0 "WORD121,Message Buffer 21 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS22,Message Buffer 22 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB14_16B_WORD2_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x3 line.long 0x0 "MB22_8B_CS,Message Buffer 22 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E0++0x3 line.long 0x0 "MB4_64B_WORD14_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x1E0++0x7 line.long 0x0 "MB8_32B_WORD6_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID22,Message Buffer 22 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB14_16B_WORD3_L,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x3 line.long 0x0 "MB22_8B_ID,Message Buffer 22 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1E4++0x3 line.long 0x0 "MB4_64B_WORD15_L,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x1E4++0x7 line.long 0x0 "MB8_32B_WORD7_L,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_L,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB22_8B_WORD0,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1E8++0x3 line.long 0x0 "MB5_64B_CS_L,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x3 line.long 0x0 "MB9_32B_CS_L,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1E8++0x7 line.long 0x0 "WORD022,Message Buffer 22 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_L,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB22_8B_WORD1,Message Buffer 22 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1EC++0x3 line.long 0x0 "MB5_64B_ID_L,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x3 line.long 0x0 "MB9_32B_ID_L,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1EC++0x7 line.long 0x0 "WORD122,Message Buffer 22 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS23,Message Buffer 23 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB15_16B_WORD0_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x3 line.long 0x0 "MB23_8B_CS,Message Buffer 23 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x1F0++0x3 line.long 0x0 "MB5_64B_WORD0_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F0++0x7 line.long 0x0 "MB9_32B_WORD0_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID23,Message Buffer 23 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB15_16B_WORD1_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x3 line.long 0x0 "MB23_8B_ID,Message Buffer 23 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x1F4++0x3 line.long 0x0 "MB5_64B_WORD1_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1F4++0x7 line.long 0x0 "MB9_32B_WORD1_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB23_8B_WORD0,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB5_64B_WORD2_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x3 line.long 0x0 "MB9_32B_WORD2_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x1F8++0x7 line.long 0x0 "WORD023,Message Buffer 23 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_L,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB23_8B_WORD1,Message Buffer 23 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB5_64B_WORD3_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x3 line.long 0x0 "MB9_32B_WORD3_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x1FC++0x7 line.long 0x0 "WORD123,Message Buffer 23 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS24,Message Buffer 24 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB16_16B_CS_L,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB24_8B_CS,Message Buffer 24 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x200++0x3 line.long 0x0 "MB5_64B_WORD4_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x200++0x7 line.long 0x0 "MB9_32B_WORD4_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID24,Message Buffer 24 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB16_16B_ID_L,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB24_8B_ID,Message Buffer 24 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x204++0x3 line.long 0x0 "MB5_64B_WORD5_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x204++0x7 line.long 0x0 "MB9_32B_WORD5_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB24_8B_WORD0,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB5_64B_WORD6_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x3 line.long 0x0 "MB9_32B_WORD6_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x208++0x7 line.long 0x0 "WORD024,Message Buffer 24 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB24_8B_WORD1,Message Buffer 24 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB5_64B_WORD7_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x3 line.long 0x0 "MB9_32B_WORD7_L,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x20C++0x7 line.long 0x0 "WORD124,Message Buffer 24 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS25,Message Buffer 25 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB10_32B_CS_L,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x3 line.long 0x0 "MB16_16B_WORD2_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x210++0x3 line.long 0x0 "MB25_8B_CS,Message Buffer 25 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x210++0x7 line.long 0x0 "MB5_64B_WORD8_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID25,Message Buffer 25 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB10_32B_ID_L,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x3 line.long 0x0 "MB16_16B_WORD3_L,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x214++0x3 line.long 0x0 "MB25_8B_ID,Message Buffer 25 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x214++0x7 line.long 0x0 "MB5_64B_WORD9_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB17_16B_CS_L,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x218++0x3 line.long 0x0 "MB25_8B_WORD0,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x218++0x3 line.long 0x0 "MB5_64B_WORD10_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x218++0x7 line.long 0x0 "WORD025,Message Buffer 25 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB17_16B_ID_L,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x21C++0x3 line.long 0x0 "MB25_8B_WORD1,Message Buffer 25 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x3 line.long 0x0 "MB5_64B_WORD11_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x21C++0x7 line.long 0x0 "WORD125,Message Buffer 25 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS26,Message Buffer 26 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x3 line.long 0x0 "MB10_32B_WORD2_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB17_16B_WORD0_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x220++0x3 line.long 0x0 "MB26_8B_CS,Message Buffer 26 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x220++0x7 line.long 0x0 "MB5_64B_WORD12_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID26,Message Buffer 26 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x3 line.long 0x0 "MB10_32B_WORD3_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB17_16B_WORD1_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x224++0x3 line.long 0x0 "MB26_8B_ID,Message Buffer 26 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x224++0x7 line.long 0x0 "MB5_64B_WORD13_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB17_16B_WORD2_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB26_8B_WORD0,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x228++0x3 line.long 0x0 "MB5_64B_WORD14_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x228++0x7 line.long 0x0 "WORD026,Message Buffer 26 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB17_16B_WORD3_L,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB26_8B_WORD1,Message Buffer 26 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x3 line.long 0x0 "MB5_64B_WORD15_L,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x22C++0x7 line.long 0x0 "WORD126,Message Buffer 26 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS27,Message Buffer 27 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB10_32B_WORD6_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x230++0x3 line.long 0x0 "MB18_16B_CS_L,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x3 line.long 0x0 "MB27_8B_CS,Message Buffer 27 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x230++0x7 line.long 0x0 "MB6_64B_CS_L,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID27,Message Buffer 27 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB10_32B_WORD7_L,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x234++0x3 line.long 0x0 "MB18_16B_ID_L,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x3 line.long 0x0 "MB27_8B_ID,Message Buffer 27 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x234++0x7 line.long 0x0 "MB6_64B_ID_L,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_L,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x238++0x3 line.long 0x0 "MB18_16B_WORD0_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB27_8B_WORD0,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x3 line.long 0x0 "MB6_64B_WORD0_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x238++0x7 line.long 0x0 "WORD027,Message Buffer 27 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_L,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x23C++0x3 line.long 0x0 "MB18_16B_WORD1_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB27_8B_WORD1,Message Buffer 27 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x3 line.long 0x0 "MB6_64B_WORD1_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x23C++0x7 line.long 0x0 "WORD127,Message Buffer 27 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS28,Message Buffer 28 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x3 line.long 0x0 "MB11_32B_WORD0_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB18_16B_WORD2_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x240++0x3 line.long 0x0 "MB28_8B_CS,Message Buffer 28 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x240++0x7 line.long 0x0 "MB6_64B_WORD2_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID28,Message Buffer 28 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x3 line.long 0x0 "MB11_32B_WORD1_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB18_16B_WORD3_L,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x244++0x3 line.long 0x0 "MB28_8B_ID,Message Buffer 28 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x244++0x7 line.long 0x0 "MB6_64B_WORD3_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB19_16B_CS_L,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x248++0x3 line.long 0x0 "MB28_8B_WORD0,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x248++0x3 line.long 0x0 "MB6_64B_WORD4_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x248++0x7 line.long 0x0 "WORD028,Message Buffer 28 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB19_16B_ID_L,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x24C++0x3 line.long 0x0 "MB28_8B_WORD1,Message Buffer 28 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x3 line.long 0x0 "MB6_64B_WORD5_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x24C++0x7 line.long 0x0 "WORD128,Message Buffer 28 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS29,Message Buffer 29 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x3 line.long 0x0 "MB11_32B_WORD4_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB19_16B_WORD0_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x250++0x3 line.long 0x0 "MB29_8B_CS,Message Buffer 29 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x250++0x7 line.long 0x0 "MB6_64B_WORD6_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID29,Message Buffer 29 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x3 line.long 0x0 "MB11_32B_WORD5_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB19_16B_WORD1_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x254++0x3 line.long 0x0 "MB29_8B_ID,Message Buffer 29 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x254++0x7 line.long 0x0 "MB6_64B_WORD7_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB19_16B_WORD2_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB29_8B_WORD0,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x258++0x3 line.long 0x0 "MB6_64B_WORD8_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x258++0x7 line.long 0x0 "WORD029,Message Buffer 29 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_L,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB19_16B_WORD3_L,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB29_8B_WORD1,Message Buffer 29 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x3 line.long 0x0 "MB6_64B_WORD9_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x25C++0x7 line.long 0x0 "WORD129,Message Buffer 29 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS30,Message Buffer 30 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB20_16B_CS_L,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x3 line.long 0x0 "MB30_8B_CS,Message Buffer 30 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x260++0x7 line.long 0x0 "MB6_64B_WORD10_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID30,Message Buffer 30 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB20_16B_ID_L,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x3 line.long 0x0 "MB30_8B_ID,Message Buffer 30 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x264++0x7 line.long 0x0 "MB6_64B_WORD11_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB30_8B_WORD0,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x268++0x3 line.long 0x0 "MB6_64B_WORD12_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x268++0x7 line.long 0x0 "WORD030,Message Buffer 30 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB30_8B_WORD1,Message Buffer 30 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x3 line.long 0x0 "MB6_64B_WORD13_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x26C++0x7 line.long 0x0 "WORD130,Message Buffer 30 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS31,Message Buffer 31 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x3 line.long 0x0 "MB20_16B_WORD2_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x270++0x3 line.long 0x0 "MB31_8B_CS,Message Buffer 31 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x270++0x7 line.long 0x0 "MB6_64B_WORD14_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID31,Message Buffer 31 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x3 line.long 0x0 "MB20_16B_WORD3_L,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x274++0x3 line.long 0x0 "MB31_8B_ID,Message Buffer 31 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x274++0x7 line.long 0x0 "MB6_64B_WORD15_L,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD0,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x278++0x7 line.long 0x0 "WORD031,Message Buffer 31 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB31_8B_WORD1,Message Buffer 31 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x27C++0x7 line.long 0x0 "WORD131,Message Buffer 31 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS32,Message Buffer 32 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_16B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_32B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x3 line.long 0x0 "MB0_64B_CS_H,Message Buffer 0 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x280++0x7 line.long 0x0 "MB32_8B_CS,Message Buffer 32 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID32,Message Buffer 32 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_16B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_32B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x3 line.long 0x0 "MB0_64B_ID_H,Message Buffer 0 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x284++0x7 line.long 0x0 "MB32_8B_ID,Message Buffer 32 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_16B_WORD0_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_32B_WORD0_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB0_64B_WORD0_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x3 line.long 0x0 "MB32_8B_WORD0,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x288++0x7 line.long 0x0 "WORD032,Message Buffer 32 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_16B_WORD1_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_32B_WORD1_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB0_64B_WORD1_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x3 line.long 0x0 "MB32_8B_WORD1,Message Buffer 32 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x28C++0x7 line.long 0x0 "WORD132,Message Buffer 32 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS33,Message Buffer 33 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x290++0x3 line.long 0x0 "MB0_16B_WORD2_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_32B_WORD2_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x3 line.long 0x0 "MB0_64B_WORD2_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x290++0x7 line.long 0x0 "MB33_8B_CS,Message Buffer 33 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID33,Message Buffer 33 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x294++0x3 line.long 0x0 "MB0_16B_WORD3_H,Message Buffer 0 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_32B_WORD3_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x3 line.long 0x0 "MB0_64B_WORD3_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x294++0x7 line.long 0x0 "MB33_8B_ID,Message Buffer 33 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_32B_WORD4_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB0_64B_WORD4_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x298++0x3 line.long 0x0 "MB1_16B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x298++0x3 line.long 0x0 "MB33_8B_WORD0,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x298++0x7 line.long 0x0 "WORD033,Message Buffer 33 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_32B_WORD5_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB0_64B_WORD5_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x3 line.long 0x0 "MB1_16B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x29C++0x3 line.long 0x0 "MB33_8B_WORD1,Message Buffer 33 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x29C++0x7 line.long 0x0 "WORD133,Message Buffer 33 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS34,Message Buffer 34 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A0++0x3 line.long 0x0 "MB0_32B_WORD6_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB0_64B_WORD6_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x3 line.long 0x0 "MB1_16B_WORD0_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A0++0x7 line.long 0x0 "MB34_8B_CS,Message Buffer 34 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID34,Message Buffer 34 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2A4++0x3 line.long 0x0 "MB0_32B_WORD7_H,Message Buffer 0 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB0_64B_WORD7_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x3 line.long 0x0 "MB1_16B_WORD1_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2A4++0x7 line.long 0x0 "MB34_8B_ID,Message Buffer 34 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD8_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_16B_WORD2_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x3 line.long 0x0 "MB1_32B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2A8++0x3 line.long 0x0 "MB34_8B_WORD0,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2A8++0x7 line.long 0x0 "WORD034,Message Buffer 34 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD9_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_16B_WORD3_H,Message Buffer 1 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x3 line.long 0x0 "MB1_32B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2AC++0x3 line.long 0x0 "MB34_8B_WORD1,Message Buffer 34 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2AC++0x7 line.long 0x0 "WORD134,Message Buffer 34 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS35,Message Buffer 35 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x3 line.long 0x0 "MB0_64B_WORD10_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB1_32B_WORD0_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B0++0x3 line.long 0x0 "MB2_16B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2B0++0x7 line.long 0x0 "MB35_8B_CS,Message Buffer 35 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID35,Message Buffer 35 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x3 line.long 0x0 "MB0_64B_WORD11_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB1_32B_WORD1_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2B4++0x3 line.long 0x0 "MB2_16B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2B4++0x7 line.long 0x0 "MB35_8B_ID,Message Buffer 35 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB0_64B_WORD12_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB1_32B_WORD2_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB2_16B_WORD0_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x3 line.long 0x0 "MB35_8B_WORD0,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2B8++0x7 line.long 0x0 "WORD035,Message Buffer 35 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB0_64B_WORD13_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB1_32B_WORD3_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB2_16B_WORD1_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x3 line.long 0x0 "MB35_8B_WORD1,Message Buffer 35 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2BC++0x7 line.long 0x0 "WORD135,Message Buffer 35 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS36,Message Buffer 36 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C0++0x3 line.long 0x0 "MB0_64B_WORD14_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB1_32B_WORD4_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x3 line.long 0x0 "MB2_16B_WORD2_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2C0++0x7 line.long 0x0 "MB36_8B_CS,Message Buffer 36 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID36,Message Buffer 36 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2C4++0x3 line.long 0x0 "MB0_64B_WORD15_H,Message Buffer 0 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB1_32B_WORD5_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x3 line.long 0x0 "MB2_16B_WORD3_H,Message Buffer 2 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2C4++0x7 line.long 0x0 "MB36_8B_ID,Message Buffer 36 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_32B_WORD6_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB1_64B_CS_H,Message Buffer 1 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x3 line.long 0x0 "MB36_8B_WORD0,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2C8++0x3 line.long 0x0 "MB3_16B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2C8++0x7 line.long 0x0 "WORD036,Message Buffer 36 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_32B_WORD7_H,Message Buffer 1 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB1_64B_ID_H,Message Buffer 1 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x3 line.long 0x0 "MB36_8B_WORD1,Message Buffer 36 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2CC++0x3 line.long 0x0 "MB3_16B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2CC++0x7 line.long 0x0 "WORD136,Message Buffer 36 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS37,Message Buffer 37 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB1_64B_WORD0_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D0++0x3 line.long 0x0 "MB2_32B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x3 line.long 0x0 "MB37_8B_CS,Message Buffer 37 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2D0++0x7 line.long 0x0 "MB3_16B_WORD0_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID37,Message Buffer 37 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB1_64B_WORD1_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2D4++0x3 line.long 0x0 "MB2_32B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x3 line.long 0x0 "MB37_8B_ID,Message Buffer 37 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2D4++0x7 line.long 0x0 "MB3_16B_WORD1_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD2_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB2_32B_WORD0_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB37_8B_WORD0,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x3 line.long 0x0 "MB3_16B_WORD2_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2D8++0x7 line.long 0x0 "WORD037,Message Buffer 37 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD3_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB2_32B_WORD1_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB37_8B_WORD1,Message Buffer 37 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x3 line.long 0x0 "MB3_16B_WORD3_H,Message Buffer 3 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2DC++0x7 line.long 0x0 "WORD137,Message Buffer 37 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS38,Message Buffer 38 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x3 line.long 0x0 "MB1_64B_WORD4_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB2_32B_WORD2_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x2E0++0x3 line.long 0x0 "MB38_8B_CS,Message Buffer 38 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2E0++0x7 line.long 0x0 "MB4_16B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID38,Message Buffer 38 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x3 line.long 0x0 "MB1_64B_WORD5_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB2_32B_WORD3_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x2E4++0x3 line.long 0x0 "MB38_8B_ID,Message Buffer 38 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2E4++0x7 line.long 0x0 "MB4_16B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB1_64B_WORD6_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB2_32B_WORD4_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB38_8B_WORD0,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x3 line.long 0x0 "MB4_16B_WORD0_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2E8++0x7 line.long 0x0 "WORD038,Message Buffer 38 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD7_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB2_32B_WORD5_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB38_8B_WORD1,Message Buffer 38 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x3 line.long 0x0 "MB4_16B_WORD1_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2EC++0x7 line.long 0x0 "WORD138,Message Buffer 38 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS39,Message Buffer 39 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x3 line.long 0x0 "MB1_64B_WORD8_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB2_32B_WORD6_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x2F0++0x3 line.long 0x0 "MB39_8B_CS,Message Buffer 39 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F0++0x7 line.long 0x0 "MB4_16B_WORD2_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID39,Message Buffer 39 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x3 line.long 0x0 "MB1_64B_WORD9_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB2_32B_WORD7_H,Message Buffer 2 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x2F4++0x3 line.long 0x0 "MB39_8B_ID,Message Buffer 39 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2F4++0x7 line.long 0x0 "MB4_16B_WORD3_H,Message Buffer 4 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD10_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB39_8B_WORD0,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x2F8++0x3 line.long 0x0 "MB3_32B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x3 line.long 0x0 "MB5_16B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x2F8++0x7 line.long 0x0 "WORD039,Message Buffer 39 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD11_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB39_8B_WORD1,Message Buffer 39 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x2FC++0x3 line.long 0x0 "MB3_32B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x3 line.long 0x0 "MB5_16B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x2FC++0x7 line.long 0x0 "WORD139,Message Buffer 39 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS40,Message Buffer 40 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x3 line.long 0x0 "MB1_64B_WORD12_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB3_32B_WORD0_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x300++0x3 line.long 0x0 "MB40_8B_CS,Message Buffer 40 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x300++0x7 line.long 0x0 "MB5_16B_WORD0_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID40,Message Buffer 40 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x3 line.long 0x0 "MB1_64B_WORD13_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB3_32B_WORD1_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x304++0x3 line.long 0x0 "MB40_8B_ID,Message Buffer 40 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x304++0x7 line.long 0x0 "MB5_16B_WORD1_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD14_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB3_32B_WORD2_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB40_8B_WORD0,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x308++0x3 line.long 0x0 "MB5_16B_WORD2_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x308++0x7 line.long 0x0 "WORD040,Message Buffer 40 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB1_64B_WORD15_H,Message Buffer 1 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB3_32B_WORD3_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB40_8B_WORD1,Message Buffer 40 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x3 line.long 0x0 "MB5_16B_WORD3_H,Message Buffer 5 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x30C++0x7 line.long 0x0 "WORD140,Message Buffer 40 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS41,Message Buffer 41 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB2_64B_CS_H,Message Buffer 2 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x3 line.long 0x0 "MB3_32B_WORD4_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x310++0x3 line.long 0x0 "MB41_8B_CS,Message Buffer 41 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x310++0x7 line.long 0x0 "MB6_16B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID41,Message Buffer 41 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB2_64B_ID_H,Message Buffer 2 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x3 line.long 0x0 "MB3_32B_WORD5_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x314++0x3 line.long 0x0 "MB41_8B_ID,Message Buffer 41 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x314++0x7 line.long 0x0 "MB6_16B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD0_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB3_32B_WORD6_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB41_8B_WORD0,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x3 line.long 0x0 "MB6_16B_WORD0_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x318++0x7 line.long 0x0 "WORD041,Message Buffer 41 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD1_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB3_32B_WORD7_H,Message Buffer 3 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB41_8B_WORD1,Message Buffer 41 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x3 line.long 0x0 "MB6_16B_WORD1_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x31C++0x7 line.long 0x0 "WORD141,Message Buffer 41 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS42,Message Buffer 42 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB2_64B_WORD2_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x320++0x3 line.long 0x0 "MB42_8B_CS,Message Buffer 42 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x3 line.long 0x0 "MB4_32B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x320++0x7 line.long 0x0 "MB6_16B_WORD2_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID42,Message Buffer 42 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB2_64B_WORD3_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x324++0x3 line.long 0x0 "MB42_8B_ID,Message Buffer 42 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x3 line.long 0x0 "MB4_32B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x324++0x7 line.long 0x0 "MB6_16B_WORD3_H,Message Buffer 6 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD4_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB42_8B_WORD0,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB4_32B_WORD0_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x328++0x3 line.long 0x0 "MB7_16B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x328++0x7 line.long 0x0 "WORD042,Message Buffer 42 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD5_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB42_8B_WORD1,Message Buffer 42 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB4_32B_WORD1_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x32C++0x3 line.long 0x0 "MB7_16B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x32C++0x7 line.long 0x0 "WORD142,Message Buffer 42 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS43,Message Buffer 43 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB2_64B_WORD6_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x330++0x3 line.long 0x0 "MB43_8B_CS,Message Buffer 43 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x330++0x3 line.long 0x0 "MB4_32B_WORD2_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x330++0x7 line.long 0x0 "MB7_16B_WORD0_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID43,Message Buffer 43 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB2_64B_WORD7_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x334++0x3 line.long 0x0 "MB43_8B_ID,Message Buffer 43 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x334++0x3 line.long 0x0 "MB4_32B_WORD3_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x334++0x7 line.long 0x0 "MB7_16B_WORD1_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD8_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB43_8B_WORD0,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB4_32B_WORD4_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x338++0x3 line.long 0x0 "MB7_16B_WORD2_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x338++0x7 line.long 0x0 "WORD043,Message Buffer 43 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD9_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB43_8B_WORD1,Message Buffer 43 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB4_32B_WORD5_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x3 line.long 0x0 "MB7_16B_WORD3_H,Message Buffer 7 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x33C++0x7 line.long 0x0 "WORD143,Message Buffer 43 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS44,Message Buffer 44 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB2_64B_WORD10_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x340++0x3 line.long 0x0 "MB44_8B_CS,Message Buffer 44 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x340++0x3 line.long 0x0 "MB4_32B_WORD6_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x340++0x7 line.long 0x0 "MB8_16B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID44,Message Buffer 44 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB2_64B_WORD11_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x344++0x3 line.long 0x0 "MB44_8B_ID,Message Buffer 44 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x344++0x3 line.long 0x0 "MB4_32B_WORD7_H,Message Buffer 4 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x344++0x7 line.long 0x0 "MB8_16B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB2_64B_WORD12_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB44_8B_WORD0,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x3 line.long 0x0 "MB5_32B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x348++0x3 line.long 0x0 "MB8_16B_WORD0_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x348++0x7 line.long 0x0 "WORD044,Message Buffer 44 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB2_64B_WORD13_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB44_8B_WORD1,Message Buffer 44 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x3 line.long 0x0 "MB5_32B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x34C++0x3 line.long 0x0 "MB8_16B_WORD1_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x34C++0x7 line.long 0x0 "WORD144,Message Buffer 44 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS45,Message Buffer 45 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB2_64B_WORD14_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x350++0x3 line.long 0x0 "MB45_8B_CS,Message Buffer 45 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x350++0x3 line.long 0x0 "MB5_32B_WORD0_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x350++0x7 line.long 0x0 "MB8_16B_WORD2_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID45,Message Buffer 45 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB2_64B_WORD15_H,Message Buffer 2 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x354++0x3 line.long 0x0 "MB45_8B_ID,Message Buffer 45 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x354++0x3 line.long 0x0 "MB5_32B_WORD1_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x354++0x7 line.long 0x0 "MB8_16B_WORD3_H,Message Buffer 8 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_CS_H,Message Buffer 3 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x3 line.long 0x0 "MB45_8B_WORD0,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB5_32B_WORD2_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x358++0x3 line.long 0x0 "MB9_16B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x358++0x7 line.long 0x0 "WORD045,Message Buffer 45 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_ID_H,Message Buffer 3 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x3 line.long 0x0 "MB45_8B_WORD1,Message Buffer 45 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB5_32B_WORD3_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x35C++0x3 line.long 0x0 "MB9_16B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x35C++0x7 line.long 0x0 "WORD145,Message Buffer 45 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS46,Message Buffer 46 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB3_64B_WORD0_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x360++0x3 line.long 0x0 "MB46_8B_CS,Message Buffer 46 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x360++0x3 line.long 0x0 "MB5_32B_WORD4_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x360++0x7 line.long 0x0 "MB9_16B_WORD0_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID46,Message Buffer 46 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB3_64B_WORD1_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x364++0x3 line.long 0x0 "MB46_8B_ID,Message Buffer 46 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x364++0x3 line.long 0x0 "MB5_32B_WORD5_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x364++0x7 line.long 0x0 "MB9_16B_WORD1_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD2_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB46_8B_WORD0,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB5_32B_WORD6_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x368++0x3 line.long 0x0 "MB9_16B_WORD2_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x368++0x7 line.long 0x0 "WORD046,Message Buffer 46 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB3_64B_WORD3_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB46_8B_WORD1,Message Buffer 46 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB5_32B_WORD7_H,Message Buffer 5 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x3 line.long 0x0 "MB9_16B_WORD3_H,Message Buffer 9 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x36C++0x7 line.long 0x0 "WORD146,Message Buffer 46 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS47,Message Buffer 47 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB10_16B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x3 line.long 0x0 "MB3_64B_WORD4_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x370++0x3 line.long 0x0 "MB47_8B_CS,Message Buffer 47 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x370++0x7 line.long 0x0 "MB6_32B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID47,Message Buffer 47 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB10_16B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x3 line.long 0x0 "MB3_64B_WORD5_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x374++0x3 line.long 0x0 "MB47_8B_ID,Message Buffer 47 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x374++0x7 line.long 0x0 "MB6_32B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB10_16B_WORD0_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB3_64B_WORD6_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB47_8B_WORD0,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x3 line.long 0x0 "MB6_32B_WORD0_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x378++0x7 line.long 0x0 "WORD047,Message Buffer 47 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_16B_WORD1_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB3_64B_WORD7_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB47_8B_WORD1,Message Buffer 47 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x3 line.long 0x0 "MB6_32B_WORD1_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x37C++0x7 line.long 0x0 "WORD147,Message Buffer 47 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS48,Message Buffer 48 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x3 line.long 0x0 "MB10_16B_WORD2_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB3_64B_WORD8_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x380++0x3 line.long 0x0 "MB48_8B_CS,Message Buffer 48 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x380++0x7 line.long 0x0 "MB6_32B_WORD2_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID48,Message Buffer 48 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x3 line.long 0x0 "MB10_16B_WORD3_H,Message Buffer 10 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB3_64B_WORD9_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x384++0x3 line.long 0x0 "MB48_8B_ID,Message Buffer 48 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x384++0x7 line.long 0x0 "MB6_32B_WORD3_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x388++0x3 line.long 0x0 "MB3_64B_WORD10_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB48_8B_WORD0,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x388++0x3 line.long 0x0 "MB6_32B_WORD4_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x388++0x7 line.long 0x0 "WORD048,Message Buffer 48 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x38C++0x3 line.long 0x0 "MB3_64B_WORD11_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB48_8B_WORD1,Message Buffer 48 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x3 line.long 0x0 "MB6_32B_WORD5_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x38C++0x7 line.long 0x0 "WORD148,Message Buffer 48 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS49,Message Buffer 49 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x3 line.long 0x0 "MB11_16B_WORD0_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB3_64B_WORD12_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x390++0x3 line.long 0x0 "MB49_8B_CS,Message Buffer 49 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x390++0x7 line.long 0x0 "MB6_32B_WORD6_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID49,Message Buffer 49 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x3 line.long 0x0 "MB11_16B_WORD1_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB3_64B_WORD13_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x394++0x3 line.long 0x0 "MB49_8B_ID,Message Buffer 49 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x394++0x7 line.long 0x0 "MB6_32B_WORD7_H,Message Buffer 6 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD2_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB3_64B_WORD14_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB49_8B_WORD0,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x398++0x3 line.long 0x0 "MB7_32B_CS_H,Message Buffer 7 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x398++0x7 line.long 0x0 "WORD049,Message Buffer 49 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_16B_WORD3_H,Message Buffer 11 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB3_64B_WORD15_H,Message Buffer 3 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB49_8B_WORD1,Message Buffer 49 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x39C++0x3 line.long 0x0 "MB7_32B_ID_H,Message Buffer 7 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x39C++0x7 line.long 0x0 "WORD149,Message Buffer 49 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS50,Message Buffer 50 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB12_16B_CS_H,Message Buffer 12 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB4_64B_CS_H,Message Buffer 4 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x3 line.long 0x0 "MB50_8B_CS,Message Buffer 50 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3A0++0x7 line.long 0x0 "MB7_32B_WORD0_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID50,Message Buffer 50 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB12_16B_ID_H,Message Buffer 12 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB4_64B_ID_H,Message Buffer 4 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x3 line.long 0x0 "MB50_8B_ID,Message Buffer 50 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3A4++0x7 line.long 0x0 "MB7_32B_WORD1_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD0_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB4_64B_WORD0_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB50_8B_WORD0,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x3 line.long 0x0 "MB7_32B_WORD2_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3A8++0x7 line.long 0x0 "WORD050,Message Buffer 50 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB12_16B_WORD1_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB4_64B_WORD1_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB50_8B_WORD1,Message Buffer 50 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x3 line.long 0x0 "MB7_32B_WORD3_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3AC++0x7 line.long 0x0 "WORD150,Message Buffer 50 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS51,Message Buffer 51 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x3 line.long 0x0 "MB12_16B_WORD2_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB4_64B_WORD2_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3B0++0x3 line.long 0x0 "MB51_8B_CS,Message Buffer 51 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B0++0x7 line.long 0x0 "MB7_32B_WORD4_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID51,Message Buffer 51 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x3 line.long 0x0 "MB12_16B_WORD3_H,Message Buffer 12 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB4_64B_WORD3_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3B4++0x3 line.long 0x0 "MB51_8B_ID,Message Buffer 51 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3B4++0x7 line.long 0x0 "MB7_32B_WORD5_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_CS_H,Message Buffer 13 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3B8++0x3 line.long 0x0 "MB4_64B_WORD4_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB51_8B_WORD0,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x3 line.long 0x0 "MB7_32B_WORD6_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3B8++0x7 line.long 0x0 "WORD051,Message Buffer 51 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_ID_H,Message Buffer 13 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3BC++0x3 line.long 0x0 "MB4_64B_WORD5_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB51_8B_WORD1,Message Buffer 51 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x3 line.long 0x0 "MB7_32B_WORD7_H,Message Buffer 7 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3BC++0x7 line.long 0x0 "WORD151,Message Buffer 51 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS52,Message Buffer 52 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x3 line.long 0x0 "MB13_16B_WORD0_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB4_64B_WORD6_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x3C0++0x3 line.long 0x0 "MB52_8B_CS,Message Buffer 52 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3C0++0x7 line.long 0x0 "MB8_32B_CS_H,Message Buffer 8 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID52,Message Buffer 52 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x3 line.long 0x0 "MB13_16B_WORD1_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB4_64B_WORD7_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x3C4++0x3 line.long 0x0 "MB52_8B_ID,Message Buffer 52 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3C4++0x7 line.long 0x0 "MB8_32B_ID_H,Message Buffer 8 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB13_16B_WORD2_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB4_64B_WORD8_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB52_8B_WORD0,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x3 line.long 0x0 "MB8_32B_WORD0_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3C8++0x7 line.long 0x0 "WORD052,Message Buffer 52 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB13_16B_WORD3_H,Message Buffer 13 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB4_64B_WORD9_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB52_8B_WORD1,Message Buffer 52 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x3 line.long 0x0 "MB8_32B_WORD1_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3CC++0x7 line.long 0x0 "WORD152,Message Buffer 52 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS53,Message Buffer 53 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB14_16B_CS_H,Message Buffer 14 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x3 line.long 0x0 "MB4_64B_WORD10_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x3D0++0x3 line.long 0x0 "MB53_8B_CS,Message Buffer 53 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3D0++0x7 line.long 0x0 "MB8_32B_WORD2_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID53,Message Buffer 53 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB14_16B_ID_H,Message Buffer 14 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x3 line.long 0x0 "MB4_64B_WORD11_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x3D4++0x3 line.long 0x0 "MB53_8B_ID,Message Buffer 53 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3D4++0x7 line.long 0x0 "MB8_32B_WORD3_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD0_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB4_64B_WORD12_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB53_8B_WORD0,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x3 line.long 0x0 "MB8_32B_WORD4_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x3D8++0x7 line.long 0x0 "WORD053,Message Buffer 53 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB14_16B_WORD1_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB4_64B_WORD13_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB53_8B_WORD1,Message Buffer 53 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x3 line.long 0x0 "MB8_32B_WORD5_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x3DC++0x7 line.long 0x0 "WORD153,Message Buffer 53 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS54,Message Buffer 54 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x3 line.long 0x0 "MB14_16B_WORD2_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB4_64B_WORD14_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x3E0++0x3 line.long 0x0 "MB54_8B_CS,Message Buffer 54 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E0++0x7 line.long 0x0 "MB8_32B_WORD6_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID54,Message Buffer 54 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x3 line.long 0x0 "MB14_16B_WORD3_H,Message Buffer 14 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB4_64B_WORD15_H,Message Buffer 4 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x3E4++0x3 line.long 0x0 "MB54_8B_ID,Message Buffer 54 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3E4++0x7 line.long 0x0 "MB8_32B_WORD7_H,Message Buffer 8 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_CS_H,Message Buffer 15 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB54_8B_WORD0,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3E8++0x3 line.long 0x0 "MB5_64B_CS_H,Message Buffer 5 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x3 line.long 0x0 "MB9_32B_CS_H,Message Buffer 9 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3E8++0x7 line.long 0x0 "WORD054,Message Buffer 54 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_ID_H,Message Buffer 15 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB54_8B_WORD1,Message Buffer 54 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3EC++0x3 line.long 0x0 "MB5_64B_ID_H,Message Buffer 5 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x3 line.long 0x0 "MB9_32B_ID_H,Message Buffer 9 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3EC++0x7 line.long 0x0 "WORD154,Message Buffer 54 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS55,Message Buffer 55 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB15_16B_WORD0_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x3 line.long 0x0 "MB55_8B_CS,Message Buffer 55 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x3F0++0x3 line.long 0x0 "MB5_64B_WORD0_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F0++0x7 line.long 0x0 "MB9_32B_WORD0_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID55,Message Buffer 55 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB15_16B_WORD1_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x3 line.long 0x0 "MB55_8B_ID,Message Buffer 55 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x3F4++0x3 line.long 0x0 "MB5_64B_WORD1_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3F4++0x7 line.long 0x0 "MB9_32B_WORD1_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD2_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB55_8B_WORD0,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB5_64B_WORD2_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x3 line.long 0x0 "MB9_32B_WORD2_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x3F8++0x7 line.long 0x0 "WORD055,Message Buffer 55 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB15_16B_WORD3_H,Message Buffer 15 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB55_8B_WORD1,Message Buffer 55 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB5_64B_WORD3_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x3 line.long 0x0 "MB9_32B_WORD3_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x3FC++0x7 line.long 0x0 "WORD155,Message Buffer 55 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS56,Message Buffer 56 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB16_16B_CS_H,Message Buffer 16 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB56_8B_CS,Message Buffer 56 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x400++0x3 line.long 0x0 "MB5_64B_WORD4_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x400++0x7 line.long 0x0 "MB9_32B_WORD4_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID56,Message Buffer 56 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB16_16B_ID_H,Message Buffer 16 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB56_8B_ID,Message Buffer 56 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x404++0x3 line.long 0x0 "MB5_64B_WORD5_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x404++0x7 line.long 0x0 "MB9_32B_WORD5_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD0_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB56_8B_WORD0,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB5_64B_WORD6_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x3 line.long 0x0 "MB9_32B_WORD6_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x408++0x7 line.long 0x0 "WORD056,Message Buffer 56 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB16_16B_WORD1_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB56_8B_WORD1,Message Buffer 56 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB5_64B_WORD7_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x3 line.long 0x0 "MB9_32B_WORD7_H,Message Buffer 9 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x40C++0x7 line.long 0x0 "WORD156,Message Buffer 56 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS57,Message Buffer 57 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB10_32B_CS_H,Message Buffer 10 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x3 line.long 0x0 "MB16_16B_WORD2_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x410++0x3 line.long 0x0 "MB57_8B_CS,Message Buffer 57 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x410++0x7 line.long 0x0 "MB5_64B_WORD8_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID57,Message Buffer 57 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB10_32B_ID_H,Message Buffer 10 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x3 line.long 0x0 "MB16_16B_WORD3_H,Message Buffer 16 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x414++0x3 line.long 0x0 "MB57_8B_ID,Message Buffer 57 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x414++0x7 line.long 0x0 "MB5_64B_WORD9_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD0_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB17_16B_CS_H,Message Buffer 17 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x418++0x3 line.long 0x0 "MB57_8B_WORD0,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x418++0x3 line.long 0x0 "MB5_64B_WORD10_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." group.long 0x418++0x7 line.long 0x0 "WORD057,Message Buffer 57 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD1_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB17_16B_ID_H,Message Buffer 17 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x41C++0x3 line.long 0x0 "MB57_8B_WORD1,Message Buffer 57 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x3 line.long 0x0 "MB5_64B_WORD11_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." group.long 0x41C++0x7 line.long 0x0 "WORD157,Message Buffer 57 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS58,Message Buffer 58 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x3 line.long 0x0 "MB10_32B_WORD2_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB17_16B_WORD0_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x420++0x3 line.long 0x0 "MB58_8B_CS,Message Buffer 58 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x420++0x7 line.long 0x0 "MB5_64B_WORD12_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID58,Message Buffer 58 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x3 line.long 0x0 "MB10_32B_WORD3_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB17_16B_WORD1_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x424++0x3 line.long 0x0 "MB58_8B_ID,Message Buffer 58 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x424++0x7 line.long 0x0 "MB5_64B_WORD13_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD4_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB17_16B_WORD2_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB58_8B_WORD0,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x428++0x3 line.long 0x0 "MB5_64B_WORD14_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." group.long 0x428++0x7 line.long 0x0 "WORD058,Message Buffer 58 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB10_32B_WORD5_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB17_16B_WORD3_H,Message Buffer 17 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB58_8B_WORD1,Message Buffer 58 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x3 line.long 0x0 "MB5_64B_WORD15_H,Message Buffer 5 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." group.long 0x42C++0x7 line.long 0x0 "WORD158,Message Buffer 58 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS59,Message Buffer 59 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB10_32B_WORD6_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x430++0x3 line.long 0x0 "MB18_16B_CS_H,Message Buffer 18 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x3 line.long 0x0 "MB59_8B_CS,Message Buffer 59 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x430++0x7 line.long 0x0 "MB6_64B_CS_H,Message Buffer 6 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." line.long 0x4 "ID59,Message Buffer 59 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB10_32B_WORD7_H,Message Buffer 10 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x434++0x3 line.long 0x0 "MB18_16B_ID_H,Message Buffer 18 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x3 line.long 0x0 "MB59_8B_ID,Message Buffer 59 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x434++0x7 line.long 0x0 "MB6_64B_ID_H,Message Buffer 6 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." line.long 0x4 "MB11_32B_CS_H,Message Buffer 11 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x438++0x3 line.long 0x0 "MB18_16B_WORD0_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB59_8B_WORD0,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x3 line.long 0x0 "MB6_64B_WORD0_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x438++0x7 line.long 0x0 "WORD059,Message Buffer 59 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_ID_H,Message Buffer 11 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x43C++0x3 line.long 0x0 "MB18_16B_WORD1_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB59_8B_WORD1,Message Buffer 59 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x3 line.long 0x0 "MB6_64B_WORD1_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x43C++0x7 line.long 0x0 "WORD159,Message Buffer 59 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS60,Message Buffer 60 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x3 line.long 0x0 "MB11_32B_WORD0_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB18_16B_WORD2_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x440++0x3 line.long 0x0 "MB60_8B_CS,Message Buffer 60 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x440++0x7 line.long 0x0 "MB6_64B_WORD2_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID60,Message Buffer 60 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x3 line.long 0x0 "MB11_32B_WORD1_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB18_16B_WORD3_H,Message Buffer 18 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x444++0x3 line.long 0x0 "MB60_8B_ID,Message Buffer 60 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x444++0x7 line.long 0x0 "MB6_64B_WORD3_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD2_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB19_16B_CS_H,Message Buffer 19 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x448++0x3 line.long 0x0 "MB60_8B_WORD0,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x448++0x3 line.long 0x0 "MB6_64B_WORD4_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x448++0x7 line.long 0x0 "WORD060,Message Buffer 60 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD3_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB19_16B_ID_H,Message Buffer 19 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x44C++0x3 line.long 0x0 "MB60_8B_WORD1,Message Buffer 60 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x3 line.long 0x0 "MB6_64B_WORD5_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x44C++0x7 line.long 0x0 "WORD160,Message Buffer 60 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS61,Message Buffer 61 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x3 line.long 0x0 "MB11_32B_WORD4_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_16,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_17,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_18,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_19,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB19_16B_WORD0_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x450++0x3 line.long 0x0 "MB61_8B_CS,Message Buffer 61 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x450++0x7 line.long 0x0 "MB6_64B_WORD6_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID61,Message Buffer 61 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x3 line.long 0x0 "MB11_32B_WORD5_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_20,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_21,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_22,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_23,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB19_16B_WORD1_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x454++0x3 line.long 0x0 "MB61_8B_ID,Message Buffer 61 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x454++0x7 line.long 0x0 "MB6_64B_WORD7_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD6_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_24,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_25,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_26,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_27,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB19_16B_WORD2_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB61_8B_WORD0,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x458++0x3 line.long 0x0 "MB6_64B_WORD8_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_32,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_33,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_34,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_35,Data byte 0 of Rx/Tx frame." group.long 0x458++0x7 line.long 0x0 "WORD061,Message Buffer 61 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB11_32B_WORD7_H,Message Buffer 11 WORD_32B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_28,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_29,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_30,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_31,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB19_16B_WORD3_H,Message Buffer 19 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB61_8B_WORD1,Message Buffer 61 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x3 line.long 0x0 "MB6_64B_WORD9_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_36,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_37,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_38,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_39,Data byte 0 of Rx/Tx frame." group.long 0x45C++0x7 line.long 0x0 "WORD161,Message Buffer 61 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS62,Message Buffer 62 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB20_16B_CS_H,Message Buffer 20 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x3 line.long 0x0 "MB62_8B_CS,Message Buffer 62 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x460++0x7 line.long 0x0 "MB6_64B_WORD10_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_40,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_41,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_42,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_43,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID62,Message Buffer 62 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB20_16B_ID_H,Message Buffer 20 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x3 line.long 0x0 "MB62_8B_ID,Message Buffer 62 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x464++0x7 line.long 0x0 "MB6_64B_WORD11_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_44,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_45,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_46,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_47,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD0_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB62_8B_WORD0,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x468++0x3 line.long 0x0 "MB6_64B_WORD12_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_48,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_49,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_50,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_51,Data byte 0 of Rx/Tx frame." group.long 0x468++0x7 line.long 0x0 "WORD062,Message Buffer 62 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB20_16B_WORD1_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB62_8B_WORD1,Message Buffer 62 WORD_8B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x3 line.long 0x0 "MB6_64B_WORD13_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_52,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_53,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_54,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_55,Data byte 0 of Rx/Tx frame." group.long 0x46C++0x7 line.long 0x0 "WORD162,Message Buffer 62 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." line.long 0x4 "CS63,Message Buffer 63 CS Register" bitfld.long 0x4 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x4 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x4 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x4 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x4 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x4 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x4 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x4 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x4 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x3 line.long 0x0 "MB20_16B_WORD2_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_8,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_9,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_10,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_11,Data byte 0 of Rx/Tx frame." group.long 0x470++0x3 line.long 0x0 "MB63_8B_CS,Message Buffer 63 CS Register" bitfld.long 0x0 31. "EDL,Extended Data Length. This bit distinguishes between CAN format and CAN FD format frames. The EDL bit must not be set for Message Buffers configured to RANSWER with code field 0b1010." "0,1" bitfld.long 0x0 30. "BRS,Bit Rate Switch. This bit defines whether the bit rate is switched inside a CAN FD format frame." "0,1" newline bitfld.long 0x0 29. "ESI,Error State Indicator. This bit indicates if the transmitting node is error active or error passive." "0,1" hexmask.long.byte 0x0 24.--27. 1. "CODE,Message Buffer Code. This 4-bit field can be accessed (read or write) by the CPU and by the FlexCAN module itself as part of the message buffer matching and arbitration process." newline bitfld.long 0x0 22. "SRR,Substitute Remote Request. Contains a fixed recessive bit." "0,1" bitfld.long 0x0 21. "IDE,ID Extended. One/zero for extended/standard format frame." "0,1" newline bitfld.long 0x0 20. "RTR,Remote Transmission Request. One/zero for remote/data frame." "0,1" hexmask.long.byte 0x0 16.--19. 1. "DLC,Length of the data to be stored/transmitted." newline hexmask.long.word 0x0 0.--15. 1. "TIME_STAMP,Free-Running Counter Time stamp. This 16-bit field is a copy of the Free-Running Timer captured for Tx and Rx frames at the time when the beginning of the Identifier field appears on the CAN bus." group.long 0x470++0x7 line.long 0x0 "MB6_64B_WORD14_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_56,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_57,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_58,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_59,Data byte 0 of Rx/Tx frame." line.long 0x4 "ID63,Message Buffer 63 ID Register" bitfld.long 0x4 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x4 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x4 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x3 line.long 0x0 "MB20_16B_WORD3_H,Message Buffer 20 WORD_16B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_12,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_13,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_14,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_15,Data byte 0 of Rx/Tx frame." group.long 0x474++0x3 line.long 0x0 "MB63_8B_ID,Message Buffer 63 ID Register" bitfld.long 0x0 29.--31. "PRIO,Local priority. This 3-bit fieldis only used when LPRIO_EN bit is set in MCR and it only makes sense for Tx buffers. These bits are not transmitted. They are appended to the regular ID to define the transmission priority." "?,?,?,3: bit fieldis only used when LPRIO_EN bit is set..,?,?,?,?" hexmask.long.word 0x0 18.--28. 1. "STD,Contains standard/extended (HIGH word) identifier of message buffer." newline hexmask.long.tbyte 0x0 0.--17. 1. "EXT,Contains extended (LOW word) identifier of message buffer." group.long 0x474++0x7 line.long 0x0 "MB6_64B_WORD15_H,Message Buffer 6 WORD_64B Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_60,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_61,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_62,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_63,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD0,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." group.long 0x478++0x7 line.long 0x0 "WORD063,Message Buffer 63 WORD0 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_0,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_1,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_2,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_3,Data byte 0 of Rx/Tx frame." line.long 0x4 "MB63_8B_WORD1,Message Buffer 63 WORD_8B Register" hexmask.long.byte 0x4 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x4 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x4 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x4 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." group.long 0x47C++0x3 line.long 0x0 "WORD163,Message Buffer 63 WORD1 Register" hexmask.long.byte 0x0 24.--31. 1. "DATA_BYTE_4,Data byte 3 of Rx/Tx frame." hexmask.long.byte 0x0 16.--23. 1. "DATA_BYTE_5,Data byte 2 of Rx/Tx frame." newline hexmask.long.byte 0x0 8.--15. 1. "DATA_BYTE_6,Data byte 1 of Rx/Tx frame." hexmask.long.byte 0x0 0.--7. 1. "DATA_BYTE_7,Data byte 0 of Rx/Tx frame." repeat 64. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x880)++0x3 line.long 0x0 "RXIMR[$1],Rx Individual Mask registers" hexmask.long 0x0 0.--31. 1. "MI,Individual Mask Bits" repeat.end group.long 0xAE0++0xF line.long 0x0 "MECR,Memory Error Control register" bitfld.long 0x0 31. "ECRWRDIS,Error Configuration Register Write Disable" "0: Write is enabled.,1: Write is disabled." bitfld.long 0x0 19. "HANCEI_MSK,Host Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 18. "FANCEI_MSK,FlexCAN Access With Non-Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 16. "CEI_MSK,Correctable Errors Interrupt Mask" "0: Interrupt is disabled.,1: Interrupt is enabled." newline bitfld.long 0x0 15. "HAERRIE,Host Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." bitfld.long 0x0 14. "FAERRIE,FlexCAN Access Error Injection Enable" "0: Injection is disabled.,1: Injection is enabled." newline bitfld.long 0x0 13. "EXTERRIE,Extended Error Injection Enable" "0: Error injection is applied only to the 32-bit..,1: Error injection is applied to the 64-bit word." bitfld.long 0x0 9. "RERRDIS,Error Report Disable" "0: Enable updates of the error report registers.,1: Disable updates of the error report registers." newline bitfld.long 0x0 8. "ECCDIS,Error Correction Disable" "0: Enable memory error correction.,1: Disable memory error correction." bitfld.long 0x0 7. "NCEFAFRZ,Non-Correctable Errors In FlexCAN Access Put Device In Freeze Mode" "0: Keep normal operation.,1: Put FlexCAN in Freeze mode (see section 'Freeze.." line.long 0x4 "ERRIAR,Error Injection Address register" hexmask.long.word 0x4 2.--13. 1. "INJADDR_H,Error Injection Address High" rbitfld.long 0x4 0.--1. "INJADDR_L,Error Injection Address Low" "0,1,2,3" line.long 0x8 "ERRIDPR,Error Injection Data Pattern register" hexmask.long 0x8 0.--31. 1. "DFLIP,Data flip pattern" line.long 0xC "ERRIPPR,Error Injection Parity Pattern register" hexmask.long.byte 0xC 24.--28. 1. "PFLIP3,Parity Flip Pattern For Byte 3 (most significant)" hexmask.long.byte 0xC 16.--20. 1. "PFLIP2,Parity Flip Pattern For Byte 2" newline hexmask.long.byte 0xC 8.--12. 1. "PFLIP1,Parity Flip Pattern For Byte 1" hexmask.long.byte 0xC 0.--4. 1. "PFLIP0,Parity Flip Pattern For Byte 0 (Least Significant)" rgroup.long 0xAF0++0xB line.long 0x0 "RERRAR,Error Report Address register" bitfld.long 0x0 24. "NCE,Non-Correctable Error" "0: Reporting a correctable error,1: Reporting a non-correctable error" bitfld.long 0x0 16.--18. "SAID,SAID" "0,1,2,3,4,5,6,7" newline hexmask.long.word 0x0 0.--13. 1. "ERRADDR,Address Where Error Detected" line.long 0x4 "RERRDR,Error Report Data register" hexmask.long 0x4 0.--31. 1. "RDATA,Raw data word read from memory with error" line.long 0x8 "RERRSYNR,Error Report Syndrome register" bitfld.long 0x8 31. "BE3,Byte Enabled For Byte 3 (most significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 24.--28. 1. "SYND3,Error Syndrome For Byte 3 (most significant)" newline bitfld.long 0x8 23. "BE2,Byte Enabled For Byte 2" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 16.--20. 1. "SYND2,Error Syndrome For Byte 2" newline bitfld.long 0x8 15. "BE1,Byte Enabled For Byte 1" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 8.--12. 1. "SYND1,Error Syndrome for Byte 1" newline bitfld.long 0x8 7. "BE0,Byte Enabled For Byte 0 (least significant)" "0: The byte was not read.,1: The byte was read." hexmask.long.byte 0x8 0.--4. 1. "SYND0,Error Syndrome For Byte 0 (least significant)" group.long 0xAFC++0x3 line.long 0x0 "ERRSR,Error Status register" eventfld.long 0x0 19. "HANCEIF,Host Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in host..,1: A non-correctable error was detected in a host.." eventfld.long 0x0 18. "FANCEIF,FlexCAN Access With Non-Correctable Error Interrupt Flag" "0: No non-correctable errors were detected in..,1: A non-correctable error was detected in a.." newline eventfld.long 0x0 16. "CEIF,Correctable Error Interrupt Flag" "0: No correctable errors were detected so far.,1: A correctable error was detected." eventfld.long 0x0 3. "HANCEIOF,Host Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in host..,1: Overrun on non-correctable errors in host access" newline eventfld.long 0x0 2. "FANCEIOF,FlexCAN Access With Non-Correctable Error Interrupt Overrun Flag" "0: No overrun on non-correctable errors in FlexCAN..,1: Overrun on non-correctable errors in FlexCAN.." eventfld.long 0x0 0. "CEIOF,Correctable Error Interrupt Overrun Flag" "0: No overrun on correctable errors,1: Overrun on correctable errors" group.long 0xC00++0x7 line.long 0x0 "FDCTRL,CAN FD Control register" bitfld.long 0x0 31. "FDRATE,Bit Rate Switch Enable" "0: Transmit a frame in nominal rate. The BRS bit in..,1: Transmit a frame with bit rate switching if the.." bitfld.long 0x0 19.--20. "MBDSR1,Message Buffer Data Size for Region 1" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." newline bitfld.long 0x0 16.--17. "MBDSR0,Message Buffer Data Size for Region 0" "0: Selects 8 bytes per message buffer.,1: Selects 16 bytes per message buffer.,2: Selects 32 bytes per message buffer.,3: Selects 64 bytes per message buffer." bitfld.long 0x0 15. "TDCEN,Transceiver Delay Compensation Enable" "0: TDC is disabled,1: TDC is enabled" newline eventfld.long 0x0 14. "TDCFAIL,Transceiver Delay Compensation Fail" "0: Measured loop delay is in range.,1: Measured loop delay is out of range." hexmask.long.byte 0x0 8.--12. 1. "TDCOFF,Transceiver Delay Compensation Offset" newline hexmask.long.byte 0x0 0.--5. 1. "TDCVAL,Transceiver Delay Compensation Value" line.long 0x4 "FDCBT,CAN FD Bit Timing register" hexmask.long.word 0x4 20.--29. 1. "FPRESDIV,Fast Prescaler Division Factor" bitfld.long 0x4 16.--18. "FRJW,Fast Resync Jump Width" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 10.--14. 1. "FPROPSEG,Fast Propagation Segment" bitfld.long 0x4 5.--7. "FPSEG1,Fast Phase Segment 1" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "FPSEG2,Fast Phase Segment 2" "0,1,2,3,4,5,6,7" rgroup.long 0xC08++0x3 line.long 0x0 "FDCRC,CAN FD CRC register" hexmask.long.byte 0x0 24.--30. 1. "FD_MBCRC,CRC Mailbox Number for FD_TXCRC" hexmask.long.tbyte 0x0 0.--20. 1. "FD_TXCRC,Extended Transmitted CRC value" tree.end tree.end tree "CAN_WRAPPER" base ad:0x0 tree "CAN1_WRAPPER" base ad:0x400C4000 group.long 0x9E0++0x3 line.long 0x0 "GFWR,Glitch Filter Width Register" hexmask.long.byte 0x0 0.--7. 1. "GFWR,Glitch Filter Width" tree.end tree "CAN2_WRAPPER" base ad:0x400C8000 group.long 0x9E0++0x3 line.long 0x0 "GFWR,Glitch Filter Width Register" hexmask.long.byte 0x0 0.--7. 1. "GFWR,Glitch Filter Width" tree.end tree "CAN3_WRAPPER" base ad:0x40C3C000 group.long 0x9E0++0x3 line.long 0x0 "GFWR,Glitch Filter Width Register" hexmask.long.byte 0x0 0.--7. 1. "GFWR,Glitch Filter Width" tree.end tree.end tree "CCM" base ad:0x40CC0000 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CC0000 ad:0x40CC0080 ad:0x40CC0100 ad:0x40CC0180 ad:0x40CC0200 ad:0x40CC0280 ad:0x40CC0300 ad:0x40CC0380 ad:0x40CC0400 ad:0x40CC0480 ad:0x40CC0500 ad:0x40CC0580 ad:0x40CC0600 ad:0x40CC0680 ad:0x40CC0700 ad:0x40CC0780) tree "CLOCK_ROOT[$1]" base $2 group.long ($2)++0xF line.long 0x0 "CLOCK_ROOT_CONTROL,Clock root control" bitfld.long 0x0 24. "OFF,OFF" "0: Turn on clock,1: Turn off clock" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" line.long 0x4 "CLOCK_ROOT_CONTROL_SET,Clock root control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline bitfld.long 0x4 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 0.--7. 1. "DIV,Clock divider" line.long 0x8 "CLOCK_ROOT_CONTROL_CLR,Clock root control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline eventfld.long 0x8 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 0.--7. 1. "DIV,Clock divider" line.long 0xC "CLOCK_ROOT_CONTROL_TOG,Clock root control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline bitfld.long 0xC 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 0.--7. 1. "DIV,Clock divider" rgroup.long ($2+0x20)++0x7 line.long 0x0 "CLOCK_ROOT_STATUS0,Clock root working status" bitfld.long 0x0 31. "CHANGING,Internal updating in clock root" "0: Clock Status is not updating currently,1: Clock generation logic is updating currently" newline bitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline bitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,Current clock root OFF setting" "0: Clock is running,1: Clock is disabled/off" newline bitfld.long 0x0 8.--10. "MUX,Current clock root MUX setting" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Current clock root DIV setting" line.long 0x4 "CLOCK_ROOT_STATUS1,Clock root low power status" bitfld.long 0x4 27. "UP_DONE,Clock frequency increase finish" "0: Frequency increase not completed,1: Frequency increase completed" newline bitfld.long 0x4 26. "UP_REQUEST,Clock frequency increase request" "0: Frequency increase not requested,1: Frequency increase requested" newline bitfld.long 0x4 25. "DOWN_DONE,Clock frequency decrease finish" "0: Frequency decrease not completed,1: Frequency decrease completed" newline bitfld.long 0x4 24. "DOWN_REQUEST,Clock frequency decrease request" "0: Frequency decrease not requested,1: Frequency decrease requested" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Target Setpoint" rgroup.long ($2+0x2C)++0x3 line.long 0x0 "CLOCK_ROOT_CONFIG,Clock root configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long ($2+0x30)++0xF line.long 0x0 "CLOCK_ROOT_AUTHEN,Clock root access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked,1: MODE is locked" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: Clock does NOT work in Setpoint Mode,1: Clock works in Setpoint Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked,1: Trustzone setting is locked" newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode,1: Can be changed in Non-secure mode" newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode,1: Clock can be changed in user mode" line.long 0x4 "CLOCK_ROOT_AUTHEN_SET,Clock root access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_ROOT_AUTHEN_CLR,Clock root access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_ROOT_AUTHEN_TOG,Clock root access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "CLOCK_ROOT_SETPOINT$1,Setpoint setting" hexmask.long.byte 0x0 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x0 24. "OFF,OFF" "0: ON,1: OFF" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" repeat.end tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CC0800 ad:0x40CC0880 ad:0x40CC0900 ad:0x40CC0980 ad:0x40CC0A00 ad:0x40CC0A80 ad:0x40CC0B00 ad:0x40CC0B80 ad:0x40CC0C00 ad:0x40CC0C80 ad:0x40CC0D00 ad:0x40CC0D80 ad:0x40CC0E00 ad:0x40CC0E80 ad:0x40CC0F00 ad:0x40CC0F80) tree "CLOCK_ROOT[$1]" base $2 group.long ($2)++0xF line.long 0x0 "CLOCK_ROOT_CONTROL,Clock root control" bitfld.long 0x0 24. "OFF,OFF" "0: Turn on clock,1: Turn off clock" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" line.long 0x4 "CLOCK_ROOT_CONTROL_SET,Clock root control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline bitfld.long 0x4 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 0.--7. 1. "DIV,Clock divider" line.long 0x8 "CLOCK_ROOT_CONTROL_CLR,Clock root control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline eventfld.long 0x8 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 0.--7. 1. "DIV,Clock divider" line.long 0xC "CLOCK_ROOT_CONTROL_TOG,Clock root control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline bitfld.long 0xC 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 0.--7. 1. "DIV,Clock divider" rgroup.long ($2+0x20)++0x7 line.long 0x0 "CLOCK_ROOT_STATUS0,Clock root working status" bitfld.long 0x0 31. "CHANGING,Internal updating in clock root" "0: Clock Status is not updating currently,1: Clock generation logic is updating currently" newline bitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline bitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,Current clock root OFF setting" "0: Clock is running,1: Clock is disabled/off" newline bitfld.long 0x0 8.--10. "MUX,Current clock root MUX setting" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Current clock root DIV setting" line.long 0x4 "CLOCK_ROOT_STATUS1,Clock root low power status" bitfld.long 0x4 27. "UP_DONE,Clock frequency increase finish" "0: Frequency increase not completed,1: Frequency increase completed" newline bitfld.long 0x4 26. "UP_REQUEST,Clock frequency increase request" "0: Frequency increase not requested,1: Frequency increase requested" newline bitfld.long 0x4 25. "DOWN_DONE,Clock frequency decrease finish" "0: Frequency decrease not completed,1: Frequency decrease completed" newline bitfld.long 0x4 24. "DOWN_REQUEST,Clock frequency decrease request" "0: Frequency decrease not requested,1: Frequency decrease requested" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Target Setpoint" rgroup.long ($2+0x2C)++0x3 line.long 0x0 "CLOCK_ROOT_CONFIG,Clock root configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long ($2+0x30)++0xF line.long 0x0 "CLOCK_ROOT_AUTHEN,Clock root access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked,1: MODE is locked" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: Clock does NOT work in Setpoint Mode,1: Clock works in Setpoint Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked,1: Trustzone setting is locked" newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode,1: Can be changed in Non-secure mode" newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode,1: Clock can be changed in user mode" line.long 0x4 "CLOCK_ROOT_AUTHEN_SET,Clock root access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_ROOT_AUTHEN_CLR,Clock root access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_ROOT_AUTHEN_TOG,Clock root access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "CLOCK_ROOT_SETPOINT$1,Setpoint setting" hexmask.long.byte 0x0 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x0 24. "OFF,OFF" "0: ON,1: OFF" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" repeat.end tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list ad:0x40CC1000 ad:0x40CC1080 ad:0x40CC1100 ad:0x40CC1180 ad:0x40CC1200 ad:0x40CC1280 ad:0x40CC1300 ad:0x40CC1380 ad:0x40CC1400 ad:0x40CC1480 ad:0x40CC1500 ad:0x40CC1580 ad:0x40CC1600 ad:0x40CC1680 ad:0x40CC1700 ad:0x40CC1780) tree "CLOCK_ROOT[$1]" base $2 group.long ($2)++0xF line.long 0x0 "CLOCK_ROOT_CONTROL,Clock root control" bitfld.long 0x0 24. "OFF,OFF" "0: Turn on clock,1: Turn off clock" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" line.long 0x4 "CLOCK_ROOT_CONTROL_SET,Clock root control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline bitfld.long 0x4 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 0.--7. 1. "DIV,Clock divider" line.long 0x8 "CLOCK_ROOT_CONTROL_CLR,Clock root control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline eventfld.long 0x8 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 0.--7. 1. "DIV,Clock divider" line.long 0xC "CLOCK_ROOT_CONTROL_TOG,Clock root control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline bitfld.long 0xC 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 0.--7. 1. "DIV,Clock divider" rgroup.long ($2+0x20)++0x7 line.long 0x0 "CLOCK_ROOT_STATUS0,Clock root working status" bitfld.long 0x0 31. "CHANGING,Internal updating in clock root" "0: Clock Status is not updating currently,1: Clock generation logic is updating currently" newline bitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline bitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,Current clock root OFF setting" "0: Clock is running,1: Clock is disabled/off" newline bitfld.long 0x0 8.--10. "MUX,Current clock root MUX setting" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Current clock root DIV setting" line.long 0x4 "CLOCK_ROOT_STATUS1,Clock root low power status" bitfld.long 0x4 27. "UP_DONE,Clock frequency increase finish" "0: Frequency increase not completed,1: Frequency increase completed" newline bitfld.long 0x4 26. "UP_REQUEST,Clock frequency increase request" "0: Frequency increase not requested,1: Frequency increase requested" newline bitfld.long 0x4 25. "DOWN_DONE,Clock frequency decrease finish" "0: Frequency decrease not completed,1: Frequency decrease completed" newline bitfld.long 0x4 24. "DOWN_REQUEST,Clock frequency decrease request" "0: Frequency decrease not requested,1: Frequency decrease requested" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Target Setpoint" rgroup.long ($2+0x2C)++0x3 line.long 0x0 "CLOCK_ROOT_CONFIG,Clock root configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long ($2+0x30)++0xF line.long 0x0 "CLOCK_ROOT_AUTHEN,Clock root access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked,1: MODE is locked" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: Clock does NOT work in Setpoint Mode,1: Clock works in Setpoint Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked,1: Trustzone setting is locked" newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode,1: Can be changed in Non-secure mode" newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode,1: Clock can be changed in user mode" line.long 0x4 "CLOCK_ROOT_AUTHEN_SET,Clock root access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_ROOT_AUTHEN_CLR,Clock root access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_ROOT_AUTHEN_TOG,Clock root access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "CLOCK_ROOT_SETPOINT$1,Setpoint setting" hexmask.long.byte 0x0 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x0 24. "OFF,OFF" "0: ON,1: OFF" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" repeat.end tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list ad:0x40CC1800 ad:0x40CC1880 ad:0x40CC1900 ad:0x40CC1980 ad:0x40CC1A00 ad:0x40CC1A80 ad:0x40CC1B00 ad:0x40CC1B80 ad:0x40CC1C00 ad:0x40CC1C80 ad:0x40CC1D00 ad:0x40CC1D80 ad:0x40CC1E00 ad:0x40CC1E80 ad:0x40CC1F00 ad:0x40CC1F80) tree "CLOCK_ROOT[$1]" base $2 group.long ($2)++0xF line.long 0x0 "CLOCK_ROOT_CONTROL,Clock root control" bitfld.long 0x0 24. "OFF,OFF" "0: Turn on clock,1: Turn off clock" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" line.long 0x4 "CLOCK_ROOT_CONTROL_SET,Clock root control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline bitfld.long 0x4 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 0.--7. 1. "DIV,Clock divider" line.long 0x8 "CLOCK_ROOT_CONTROL_CLR,Clock root control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline eventfld.long 0x8 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 0.--7. 1. "DIV,Clock divider" line.long 0xC "CLOCK_ROOT_CONTROL_TOG,Clock root control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline bitfld.long 0xC 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 0.--7. 1. "DIV,Clock divider" rgroup.long ($2+0x20)++0x7 line.long 0x0 "CLOCK_ROOT_STATUS0,Clock root working status" bitfld.long 0x0 31. "CHANGING,Internal updating in clock root" "0: Clock Status is not updating currently,1: Clock generation logic is updating currently" newline bitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline bitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,Current clock root OFF setting" "0: Clock is running,1: Clock is disabled/off" newline bitfld.long 0x0 8.--10. "MUX,Current clock root MUX setting" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Current clock root DIV setting" line.long 0x4 "CLOCK_ROOT_STATUS1,Clock root low power status" bitfld.long 0x4 27. "UP_DONE,Clock frequency increase finish" "0: Frequency increase not completed,1: Frequency increase completed" newline bitfld.long 0x4 26. "UP_REQUEST,Clock frequency increase request" "0: Frequency increase not requested,1: Frequency increase requested" newline bitfld.long 0x4 25. "DOWN_DONE,Clock frequency decrease finish" "0: Frequency decrease not completed,1: Frequency decrease completed" newline bitfld.long 0x4 24. "DOWN_REQUEST,Clock frequency decrease request" "0: Frequency decrease not requested,1: Frequency decrease requested" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Target Setpoint" rgroup.long ($2+0x2C)++0x3 line.long 0x0 "CLOCK_ROOT_CONFIG,Clock root configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long ($2+0x30)++0xF line.long 0x0 "CLOCK_ROOT_AUTHEN,Clock root access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked,1: MODE is locked" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: Clock does NOT work in Setpoint Mode,1: Clock works in Setpoint Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked,1: Trustzone setting is locked" newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode,1: Can be changed in Non-secure mode" newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode,1: Clock can be changed in user mode" line.long 0x4 "CLOCK_ROOT_AUTHEN_SET,Clock root access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_ROOT_AUTHEN_CLR,Clock root access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_ROOT_AUTHEN_TOG,Clock root access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "CLOCK_ROOT_SETPOINT$1,Setpoint setting" hexmask.long.byte 0x0 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x0 24. "OFF,OFF" "0: ON,1: OFF" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" repeat.end tree.end repeat.end repeat 15. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E)(list ad:0x40CC2000 ad:0x40CC2080 ad:0x40CC2100 ad:0x40CC2180 ad:0x40CC2200 ad:0x40CC2280 ad:0x40CC2300 ad:0x40CC2380 ad:0x40CC2400 ad:0x40CC2480 ad:0x40CC2500 ad:0x40CC2580 ad:0x40CC2600 ad:0x40CC2680 ad:0x40CC2700) tree "CLOCK_ROOT[$1]" base $2 group.long ($2)++0xF line.long 0x0 "CLOCK_ROOT_CONTROL,Clock root control" bitfld.long 0x0 24. "OFF,OFF" "0: Turn on clock,1: Turn off clock" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" line.long 0x4 "CLOCK_ROOT_CONTROL_SET,Clock root control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline bitfld.long 0x4 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 0.--7. 1. "DIV,Clock divider" line.long 0x8 "CLOCK_ROOT_CONTROL_CLR,Clock root control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline eventfld.long 0x8 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x8 0.--7. 1. "DIV,Clock divider" line.long 0xC "CLOCK_ROOT_CONTROL_TOG,Clock root control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline bitfld.long 0xC 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 0.--7. 1. "DIV,Clock divider" rgroup.long ($2+0x20)++0x7 line.long 0x0 "CLOCK_ROOT_STATUS0,Clock root working status" bitfld.long 0x0 31. "CHANGING,Internal updating in clock root" "0: Clock Status is not updating currently,1: Clock generation logic is updating currently" newline bitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline bitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline bitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,Current clock root OFF setting" "0: Clock is running,1: Clock is disabled/off" newline bitfld.long 0x0 8.--10. "MUX,Current clock root MUX setting" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Current clock root DIV setting" line.long 0x4 "CLOCK_ROOT_STATUS1,Clock root low power status" bitfld.long 0x4 27. "UP_DONE,Clock frequency increase finish" "0: Frequency increase not completed,1: Frequency increase completed" newline bitfld.long 0x4 26. "UP_REQUEST,Clock frequency increase request" "0: Frequency increase not requested,1: Frequency increase requested" newline bitfld.long 0x4 25. "DOWN_DONE,Clock frequency decrease finish" "0: Frequency decrease not completed,1: Frequency decrease completed" newline bitfld.long 0x4 24. "DOWN_REQUEST,Clock frequency decrease request" "0: Frequency decrease not requested,1: Frequency decrease requested" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Target Setpoint" rgroup.long ($2+0x2C)++0x3 line.long 0x0 "CLOCK_ROOT_CONFIG,Clock root configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long ($2+0x30)++0xF line.long 0x0 "CLOCK_ROOT_AUTHEN,Clock root access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked,1: MODE is locked" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: Clock does NOT work in Setpoint Mode,1: Clock works in Setpoint Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked,1: Trustzone setting is locked" newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode,1: Can be changed in Non-secure mode" newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode,1: Clock can be changed in user mode" line.long 0x4 "CLOCK_ROOT_AUTHEN_SET,Clock root access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_ROOT_AUTHEN_CLR,Clock root access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_ROOT_AUTHEN_TOG,Clock root access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" repeat 16. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x40)++0x3 line.long 0x0 "CLOCK_ROOT_SETPOINT$1,Setpoint setting" hexmask.long.byte 0x0 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x0 24. "OFF,OFF" "0: ON,1: OFF" newline bitfld.long 0x0 8.--10. "MUX,Clock multiplexer" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--7. 1. "DIV,Clock divider" repeat.end tree.end repeat.end base ad:0x40CC0000 group.long 0x4000++0xF line.long 0x0 "CLOCK_GROUP0_CONTROL,Clock group control" bitfld.long 0x0 24. "OFF,OFF" "0: Clock is running,1: Turn off clock" newline hexmask.long.byte 0x0 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x0 0.--3. 1. "DIV0,Clock divider0" line.long 0x4 "CLOCK_GROUP0_CONTROL_SET,Clock group control" bitfld.long 0x4 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0x4 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x4 0.--3. 1. "DIV0,Clock divider0" line.long 0x8 "CLOCK_GROUP0_CONTROL_CLR,Clock group control" eventfld.long 0x8 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0x8 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x8 0.--3. 1. "DIV0,Clock divider0" line.long 0xC "CLOCK_GROUP0_CONTROL_TOG,Clock group control" bitfld.long 0xC 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0xC 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0xC 0.--3. 1. "DIV0,Clock divider0" group.long 0x4020++0x3 line.long 0x0 "CLOCK_GROUP0_STATUS0,Clock group working status" rbitfld.long 0x0 31. "CHANGING,Internal updating in clock group" "0: Clock root is not updating currently,1: Clock root logic is updating currently" newline rbitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline rbitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline rbitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline rbitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x0 16.--23. 1. "RSTDIV,Clock divider" newline hexmask.long.byte 0x0 0.--3. 1. "DIV0,Clock divider" rgroup.long 0x4024++0x3 line.long 0x0 "CLOCK_GROUP0_STATUS1,Clock group low power/extend status" bitfld.long 0x0 27. "UP_DONE,Clock frequency increase complete" "0: Handshake signal with GPC status indicating..,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 26. "UP_REQUEST,Clock frequency increase request" "0: No handshake signal is not requested,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 25. "DOWN_DONE,Clock frequency decrease complete" "0: Handshake signal with GPC status indicating..,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 24. "DOWN_REQUEST,Clock frequency decrease request" "0: No handshake signal is not requested,1: Handshake signal with GPC status indicating.." newline hexmask.long.byte 0x0 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x0 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" rgroup.long 0x402C++0x3 line.long 0x0 "CLOCK_GROUP0_CONFIG,Clock group configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x4030++0x5F line.long 0x0 "CLOCK_GROUP0_AUTHEN,Clock group access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x4 "CLOCK_GROUP0_AUTHEN_SET,Clock group access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_GROUP0_AUTHEN_CLR,Clock group access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_GROUP0_AUTHEN_TOG,Clock group access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" line.long 0x10 "CLOCK_GROUP0_SETPOINT0,Setpoint setting" hexmask.long.byte 0x10 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x10 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x10 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x10 0.--3. 1. "DIV0,Clock divider" line.long 0x14 "CLOCK_GROUP0_SETPOINT1,Setpoint setting" hexmask.long.byte 0x14 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x14 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x14 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x14 0.--3. 1. "DIV0,Clock divider" line.long 0x18 "CLOCK_GROUP0_SETPOINT2,Setpoint setting" hexmask.long.byte 0x18 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x18 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x18 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x18 0.--3. 1. "DIV0,Clock divider" line.long 0x1C "CLOCK_GROUP0_SETPOINT3,Setpoint setting" hexmask.long.byte 0x1C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x1C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x1C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x1C 0.--3. 1. "DIV0,Clock divider" line.long 0x20 "CLOCK_GROUP0_SETPOINT4,Setpoint setting" hexmask.long.byte 0x20 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x20 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x20 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x20 0.--3. 1. "DIV0,Clock divider" line.long 0x24 "CLOCK_GROUP0_SETPOINT5,Setpoint setting" hexmask.long.byte 0x24 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x24 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x24 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x24 0.--3. 1. "DIV0,Clock divider" line.long 0x28 "CLOCK_GROUP0_SETPOINT6,Setpoint setting" hexmask.long.byte 0x28 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x28 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x28 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x28 0.--3. 1. "DIV0,Clock divider" line.long 0x2C "CLOCK_GROUP0_SETPOINT7,Setpoint setting" hexmask.long.byte 0x2C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x2C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x2C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x2C 0.--3. 1. "DIV0,Clock divider" line.long 0x30 "CLOCK_GROUP0_SETPOINT8,Setpoint setting" hexmask.long.byte 0x30 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x30 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x30 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x30 0.--3. 1. "DIV0,Clock divider" line.long 0x34 "CLOCK_GROUP0_SETPOINT9,Setpoint setting" hexmask.long.byte 0x34 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x34 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x34 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x34 0.--3. 1. "DIV0,Clock divider" line.long 0x38 "CLOCK_GROUP0_SETPOINT10,Setpoint setting" hexmask.long.byte 0x38 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x38 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x38 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x38 0.--3. 1. "DIV0,Clock divider" line.long 0x3C "CLOCK_GROUP0_SETPOINT11,Setpoint setting" hexmask.long.byte 0x3C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x3C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x3C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x3C 0.--3. 1. "DIV0,Clock divider" line.long 0x40 "CLOCK_GROUP0_SETPOINT12,Setpoint setting" hexmask.long.byte 0x40 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x40 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x40 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x40 0.--3. 1. "DIV0,Clock divider" line.long 0x44 "CLOCK_GROUP0_SETPOINT13,Setpoint setting" hexmask.long.byte 0x44 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x44 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x44 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x44 0.--3. 1. "DIV0,Clock divider" line.long 0x48 "CLOCK_GROUP0_SETPOINT14,Setpoint setting" hexmask.long.byte 0x48 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x48 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x48 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x48 0.--3. 1. "DIV0,Clock divider" line.long 0x4C "CLOCK_GROUP0_SETPOINT15,Setpoint setting" hexmask.long.byte 0x4C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x4C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x4C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x4C 0.--3. 1. "DIV0,Clock divider" line.long 0x50 "CLOCK_GROUP1_CONTROL,Clock group control" bitfld.long 0x50 24. "OFF,OFF" "0: Clock is running,1: Turn off clock" newline hexmask.long.byte 0x50 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x50 0.--3. 1. "DIV0,Clock divider0" line.long 0x54 "CLOCK_GROUP1_CONTROL_SET,Clock group control" bitfld.long 0x54 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0x54 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x54 0.--3. 1. "DIV0,Clock divider0" line.long 0x58 "CLOCK_GROUP1_CONTROL_CLR,Clock group control" eventfld.long 0x58 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0x58 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x58 0.--3. 1. "DIV0,Clock divider0" line.long 0x5C "CLOCK_GROUP1_CONTROL_TOG,Clock group control" bitfld.long 0x5C 24. "OFF,OFF" "0,1" newline hexmask.long.byte 0x5C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x5C 0.--3. 1. "DIV0,Clock divider0" group.long 0x40A0++0x3 line.long 0x0 "CLOCK_GROUP1_STATUS0,Clock group working status" rbitfld.long 0x0 31. "CHANGING,Internal updating in clock group" "0: Clock root is not updating currently,1: Clock root logic is updating currently" newline rbitfld.long 0x0 30. "UPDATE_REVERSE,Internal status synchronization from clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline rbitfld.long 0x0 29. "UPDATE_FORWARD,Internal status synchronization to clock generation logic" "0: Synchronization not in process,1: Synchronization in process" newline rbitfld.long 0x0 28. "SLICE_BUSY,Internal updating in generation logic" "0: Clock generation logic is not busy,1: Clock generation logic is applying the new setting" newline rbitfld.long 0x0 27. "POWERDOWN,Current clock root POWERDOWN setting" "0: Clock root is running,1: Clock root is Powered Down" newline bitfld.long 0x0 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x0 16.--23. 1. "RSTDIV,Clock divider" newline hexmask.long.byte 0x0 0.--3. 1. "DIV0,Clock divider" rgroup.long 0x40A4++0x3 line.long 0x0 "CLOCK_GROUP1_STATUS1,Clock group low power/extend status" bitfld.long 0x0 27. "UP_DONE,Clock frequency increase complete" "0: Handshake signal with GPC status indicating..,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 26. "UP_REQUEST,Clock frequency increase request" "0: No handshake signal is not requested,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 25. "DOWN_DONE,Clock frequency decrease complete" "0: Handshake signal with GPC status indicating..,1: Handshake signal with GPC status indicating.." newline bitfld.long 0x0 24. "DOWN_REQUEST,Clock frequency decrease request" "0: No handshake signal is not requested,1: Handshake signal with GPC status indicating.." newline hexmask.long.byte 0x0 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x0 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" rgroup.long 0x40AC++0x3 line.long 0x0 "CLOCK_GROUP1_CONFIG,Clock group configuration" bitfld.long 0x0 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x40B0++0x4F line.long 0x0 "CLOCK_GROUP1_AUTHEN,Clock group access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x4 "CLOCK_GROUP1_AUTHEN_SET,Clock group access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x4 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "CLOCK_GROUP1_AUTHEN_CLR,Clock group access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x8 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "CLOCK_GROUP1_AUTHEN_TOG,Clock group access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xC 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0,1" newline bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" line.long 0x10 "CLOCK_GROUP1_SETPOINT0,Setpoint setting" hexmask.long.byte 0x10 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x10 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x10 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x10 0.--3. 1. "DIV0,Clock divider" line.long 0x14 "CLOCK_GROUP1_SETPOINT1,Setpoint setting" hexmask.long.byte 0x14 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x14 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x14 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x14 0.--3. 1. "DIV0,Clock divider" line.long 0x18 "CLOCK_GROUP1_SETPOINT2,Setpoint setting" hexmask.long.byte 0x18 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x18 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x18 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x18 0.--3. 1. "DIV0,Clock divider" line.long 0x1C "CLOCK_GROUP1_SETPOINT3,Setpoint setting" hexmask.long.byte 0x1C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x1C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x1C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x1C 0.--3. 1. "DIV0,Clock divider" line.long 0x20 "CLOCK_GROUP1_SETPOINT4,Setpoint setting" hexmask.long.byte 0x20 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x20 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x20 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x20 0.--3. 1. "DIV0,Clock divider" line.long 0x24 "CLOCK_GROUP1_SETPOINT5,Setpoint setting" hexmask.long.byte 0x24 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x24 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x24 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x24 0.--3. 1. "DIV0,Clock divider" line.long 0x28 "CLOCK_GROUP1_SETPOINT6,Setpoint setting" hexmask.long.byte 0x28 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x28 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x28 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x28 0.--3. 1. "DIV0,Clock divider" line.long 0x2C "CLOCK_GROUP1_SETPOINT7,Setpoint setting" hexmask.long.byte 0x2C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x2C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x2C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x2C 0.--3. 1. "DIV0,Clock divider" line.long 0x30 "CLOCK_GROUP1_SETPOINT8,Setpoint setting" hexmask.long.byte 0x30 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x30 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x30 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x30 0.--3. 1. "DIV0,Clock divider" line.long 0x34 "CLOCK_GROUP1_SETPOINT9,Setpoint setting" hexmask.long.byte 0x34 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x34 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x34 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x34 0.--3. 1. "DIV0,Clock divider" line.long 0x38 "CLOCK_GROUP1_SETPOINT10,Setpoint setting" hexmask.long.byte 0x38 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x38 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x38 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x38 0.--3. 1. "DIV0,Clock divider" line.long 0x3C "CLOCK_GROUP1_SETPOINT11,Setpoint setting" hexmask.long.byte 0x3C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x3C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x3C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x3C 0.--3. 1. "DIV0,Clock divider" line.long 0x40 "CLOCK_GROUP1_SETPOINT12,Setpoint setting" hexmask.long.byte 0x40 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x40 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x40 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x40 0.--3. 1. "DIV0,Clock divider" line.long 0x44 "CLOCK_GROUP1_SETPOINT13,Setpoint setting" hexmask.long.byte 0x44 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x44 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x44 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x44 0.--3. 1. "DIV0,Clock divider" line.long 0x48 "CLOCK_GROUP1_SETPOINT14,Setpoint setting" hexmask.long.byte 0x48 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x48 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x48 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x48 0.--3. 1. "DIV0,Clock divider" line.long 0x4C "CLOCK_GROUP1_SETPOINT15,Setpoint setting" hexmask.long.byte 0x4C 28.--31. 1. "GRADE,Grade" newline bitfld.long 0x4C 24. "OFF,OFF" "0: Clock is running.,1: Turn off clock." newline hexmask.long.byte 0x4C 16.--23. 1. "RSTDIV,Clock group global restart count" newline hexmask.long.byte 0x4C 0.--3. 1. "DIV0,Clock divider" repeat 8. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7)(list ad:0x40CC4800 ad:0x40CC4820 ad:0x40CC4840 ad:0x40CC4860 ad:0x40CC4880 ad:0x40CC48A0 ad:0x40CC48C0 ad:0x40CC48E0) tree "GPR_SHARED[$1]" base $2 group.long ($2)++0x1F line.long 0x0 "GPR_SHARED,General Purpose Register" hexmask.long 0x0 0.--31. 1. "GPR,GP register" line.long 0x4 "GPR_SHARED_SET,General Purpose Register" hexmask.long 0x4 0.--31. 1. "GPR,GP register" line.long 0x8 "GPR_SHARED_CLR,General Purpose Register" hexmask.long 0x8 0.--31. 1. "GPR,GP register" line.long 0xC "GPR_SHARED_TOG,General Purpose Register" hexmask.long 0xC 0.--31. 1. "GPR,GP register" line.long 0x10 "GPR_SHARED_AUTHEN,GPR access control" bitfld.long 0x10 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." bitfld.long 0x10 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x10 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." hexmask.long.byte 0x10 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x10 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." bitfld.long 0x10 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x10 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x14 "GPR_SHARED_AUTHEN_SET,GPR access control" bitfld.long 0x14 20. "LOCK_MODE,Lock low power and access mode" "0,1" bitfld.long 0x14 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x14 12. "LOCK_LIST,Lock Whitelist" "0,1" hexmask.long.byte 0x14 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x14 4. "LOCK_TZ,Lock truszone setting" "0,1" bitfld.long 0x14 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x14 0. "TZ_USER,User access" "0,1" line.long 0x18 "GPR_SHARED_AUTHEN_CLR,GPR access control" eventfld.long 0x18 20. "LOCK_MODE,Lock low power and access mode" "0,1" eventfld.long 0x18 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x18 12. "LOCK_LIST,Lock Whitelist" "0,1" hexmask.long.byte 0x18 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x18 4. "LOCK_TZ,Lock truszone setting" "0,1" eventfld.long 0x18 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x18 0. "TZ_USER,User access" "0,1" line.long 0x1C "GPR_SHARED_AUTHEN_TOG,GPR access control" bitfld.long 0x1C 20. "LOCK_MODE,Lock low power and access mode" "0,1" bitfld.long 0x1C 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x1C 12. "LOCK_LIST,Lock Whitelist" "0,1" hexmask.long.byte 0x1C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x1C 4. "LOCK_TZ,Lock truszone setting" "0,1" bitfld.long 0x1C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x1C 0. "TZ_USER,User access" "0,1" tree.end repeat.end base ad:0x40CC0000 group.long 0x4C20++0xDF line.long 0x0 "GPR_PRIVATE1,General Purpose Register" hexmask.long 0x0 0.--31. 1. "GPR,GP register" line.long 0x4 "GPR_PRIVATE1_SET,General Purpose Register" hexmask.long 0x4 0.--31. 1. "GPR,GP register" line.long 0x8 "GPR_PRIVATE1_CLR,General Purpose Register" hexmask.long 0x8 0.--31. 1. "GPR,GP register" line.long 0xC "GPR_PRIVATE1_TOG,General Purpose Register" hexmask.long 0xC 0.--31. 1. "GPR,GP register" line.long 0x10 "GPR_PRIVATE1_AUTHEN,GPR access control" bitfld.long 0x10 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x10 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x10 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x10 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x10 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x10 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x10 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x14 "GPR_PRIVATE1_AUTHEN_SET,GPR access control" bitfld.long 0x14 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x14 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x14 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x14 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x14 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x14 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x14 0. "TZ_USER,User access" "0,1" line.long 0x18 "GPR_PRIVATE1_AUTHEN_CLR,GPR access control" eventfld.long 0x18 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x18 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0x18 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x18 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x18 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x18 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x18 0. "TZ_USER,User access" "0,1" line.long 0x1C "GPR_PRIVATE1_AUTHEN_TOG,GPR access control" bitfld.long 0x1C 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x1C 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x1C 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x1C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x1C 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x1C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x1C 0. "TZ_USER,User access" "0,1" line.long 0x20 "GPR_PRIVATE2,General Purpose Register" hexmask.long 0x20 0.--31. 1. "GPR,GP register" line.long 0x24 "GPR_PRIVATE2_SET,General Purpose Register" hexmask.long 0x24 0.--31. 1. "GPR,GP register" line.long 0x28 "GPR_PRIVATE2_CLR,General Purpose Register" hexmask.long 0x28 0.--31. 1. "GPR,GP register" line.long 0x2C "GPR_PRIVATE2_TOG,General Purpose Register" hexmask.long 0x2C 0.--31. 1. "GPR,GP register" line.long 0x30 "GPR_PRIVATE2_AUTHEN,GPR access control" bitfld.long 0x30 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x30 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x30 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x30 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x30 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x30 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x30 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x34 "GPR_PRIVATE2_AUTHEN_SET,GPR access control" bitfld.long 0x34 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x34 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x34 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x34 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x34 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x34 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x34 0. "TZ_USER,User access" "0,1" line.long 0x38 "GPR_PRIVATE2_AUTHEN_CLR,GPR access control" eventfld.long 0x38 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x38 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0x38 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x38 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x38 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x38 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x38 0. "TZ_USER,User access" "0,1" line.long 0x3C "GPR_PRIVATE2_AUTHEN_TOG,GPR access control" bitfld.long 0x3C 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x3C 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x3C 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x3C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x3C 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x3C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x3C 0. "TZ_USER,User access" "0,1" line.long 0x40 "GPR_PRIVATE3,General Purpose Register" hexmask.long 0x40 0.--31. 1. "GPR,GP register" line.long 0x44 "GPR_PRIVATE3_SET,General Purpose Register" hexmask.long 0x44 0.--31. 1. "GPR,GP register" line.long 0x48 "GPR_PRIVATE3_CLR,General Purpose Register" hexmask.long 0x48 0.--31. 1. "GPR,GP register" line.long 0x4C "GPR_PRIVATE3_TOG,General Purpose Register" hexmask.long 0x4C 0.--31. 1. "GPR,GP register" line.long 0x50 "GPR_PRIVATE3_AUTHEN,GPR access control" bitfld.long 0x50 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x50 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x50 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x50 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x50 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x50 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x50 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x54 "GPR_PRIVATE3_AUTHEN_SET,GPR access control" bitfld.long 0x54 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x54 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x54 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x54 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x54 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x54 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x54 0. "TZ_USER,User access" "0,1" line.long 0x58 "GPR_PRIVATE3_AUTHEN_CLR,GPR access control" eventfld.long 0x58 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x58 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0x58 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x58 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x58 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x58 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x58 0. "TZ_USER,User access" "0,1" line.long 0x5C "GPR_PRIVATE3_AUTHEN_TOG,GPR access control" bitfld.long 0x5C 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x5C 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x5C 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x5C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x5C 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x5C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x5C 0. "TZ_USER,User access" "0,1" line.long 0x60 "GPR_PRIVATE4,General Purpose Register" hexmask.long 0x60 0.--31. 1. "GPR,GP register" line.long 0x64 "GPR_PRIVATE4_SET,General Purpose Register" hexmask.long 0x64 0.--31. 1. "GPR,GP register" line.long 0x68 "GPR_PRIVATE4_CLR,General Purpose Register" hexmask.long 0x68 0.--31. 1. "GPR,GP register" line.long 0x6C "GPR_PRIVATE4_TOG,General Purpose Register" hexmask.long 0x6C 0.--31. 1. "GPR,GP register" line.long 0x70 "GPR_PRIVATE4_AUTHEN,GPR access control" bitfld.long 0x70 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x70 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x70 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x70 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x70 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x70 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x70 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x74 "GPR_PRIVATE4_AUTHEN_SET,GPR access control" bitfld.long 0x74 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x74 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x74 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x74 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x74 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x74 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x74 0. "TZ_USER,User access" "0,1" line.long 0x78 "GPR_PRIVATE4_AUTHEN_CLR,GPR access control" eventfld.long 0x78 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x78 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0x78 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x78 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x78 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x78 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x78 0. "TZ_USER,User access" "0,1" line.long 0x7C "GPR_PRIVATE4_AUTHEN_TOG,GPR access control" bitfld.long 0x7C 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x7C 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x7C 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x7C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x7C 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x7C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x7C 0. "TZ_USER,User access" "0,1" line.long 0x80 "GPR_PRIVATE5,General Purpose Register" hexmask.long 0x80 0.--31. 1. "GPR,GP register" line.long 0x84 "GPR_PRIVATE5_SET,General Purpose Register" hexmask.long 0x84 0.--31. 1. "GPR,GP register" line.long 0x88 "GPR_PRIVATE5_CLR,General Purpose Register" hexmask.long 0x88 0.--31. 1. "GPR,GP register" line.long 0x8C "GPR_PRIVATE5_TOG,General Purpose Register" hexmask.long 0x8C 0.--31. 1. "GPR,GP register" line.long 0x90 "GPR_PRIVATE5_AUTHEN,GPR access control" bitfld.long 0x90 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x90 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x90 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x90 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x90 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x90 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x90 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x94 "GPR_PRIVATE5_AUTHEN_SET,GPR access control" bitfld.long 0x94 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x94 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x94 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x94 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x94 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x94 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x94 0. "TZ_USER,User access" "0,1" line.long 0x98 "GPR_PRIVATE5_AUTHEN_CLR,GPR access control" eventfld.long 0x98 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0x98 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0x98 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x98 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0x98 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0x98 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x98 0. "TZ_USER,User access" "0,1" line.long 0x9C "GPR_PRIVATE5_AUTHEN_TOG,GPR access control" bitfld.long 0x9C 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0x9C 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0x9C 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0x9C 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x9C 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0x9C 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x9C 0. "TZ_USER,User access" "0,1" line.long 0xA0 "GPR_PRIVATE6,General Purpose Register" hexmask.long 0xA0 0.--31. 1. "GPR,GP register" line.long 0xA4 "GPR_PRIVATE6_SET,General Purpose Register" hexmask.long 0xA4 0.--31. 1. "GPR,GP register" line.long 0xA8 "GPR_PRIVATE6_CLR,General Purpose Register" hexmask.long 0xA8 0.--31. 1. "GPR,GP register" line.long 0xAC "GPR_PRIVATE6_TOG,General Purpose Register" hexmask.long 0xAC 0.--31. 1. "GPR,GP register" line.long 0xB0 "GPR_PRIVATE6_AUTHEN,GPR access control" bitfld.long 0xB0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0xB0 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0xB0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0xB0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xB0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0xB0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0xB0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0xB4 "GPR_PRIVATE6_AUTHEN_SET,GPR access control" bitfld.long 0xB4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xB4 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0xB4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xB4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xB4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xB4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xB4 0. "TZ_USER,User access" "0,1" line.long 0xB8 "GPR_PRIVATE6_AUTHEN_CLR,GPR access control" eventfld.long 0xB8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0xB8 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0xB8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xB8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0xB8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0xB8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0xB8 0. "TZ_USER,User access" "0,1" line.long 0xBC "GPR_PRIVATE6_AUTHEN_TOG,GPR access control" bitfld.long 0xBC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xBC 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0xBC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xBC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xBC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xBC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xBC 0. "TZ_USER,User access" "0,1" line.long 0xC0 "GPR_PRIVATE7,General Purpose Register" hexmask.long 0xC0 0.--31. 1. "GPR,GP register" line.long 0xC4 "GPR_PRIVATE7_SET,General Purpose Register" hexmask.long 0xC4 0.--31. 1. "GPR,GP register" line.long 0xC8 "GPR_PRIVATE7_CLR,General Purpose Register" hexmask.long 0xC8 0.--31. 1. "GPR,GP register" line.long 0xCC "GPR_PRIVATE7_TOG,General Purpose Register" hexmask.long 0xCC 0.--31. 1. "GPR,GP register" line.long 0xD0 "GPR_PRIVATE7_AUTHEN,GPR access control" bitfld.long 0xD0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0xD0 16. "DOMAIN_MODE,Low power and access control by Domain" "0: Clock does NOT work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0xD0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0xD0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xD0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0xD0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0xD0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0xD4 "GPR_PRIVATE7_AUTHEN_SET,GPR access control" bitfld.long 0xD4 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xD4 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0xD4 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xD4 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xD4 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xD4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xD4 0. "TZ_USER,User access" "0,1" line.long 0xD8 "GPR_PRIVATE7_AUTHEN_CLR,GPR access control" eventfld.long 0xD8 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline eventfld.long 0xD8 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline eventfld.long 0xD8 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xD8 8.--11. 1. "WHITE_LIST,Whitelist" newline eventfld.long 0xD8 4. "LOCK_TZ,Lock truszone setting" "0,1" newline eventfld.long 0xD8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0xD8 0. "TZ_USER,User access" "0,1" line.long 0xDC "GPR_PRIVATE7_AUTHEN_TOG,GPR access control" bitfld.long 0xDC 20. "LOCK_MODE,Lock low power and access mode" "0,1" newline bitfld.long 0xDC 16. "DOMAIN_MODE,Low power and access control by Domain" "0,1" newline bitfld.long 0xDC 12. "LOCK_LIST,Lock Whitelist" "0,1" newline hexmask.long.byte 0xDC 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0xDC 4. "LOCK_TZ,Lock truszone setting" "0,1" newline bitfld.long 0xDC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xDC 0. "TZ_USER,User access" "0,1" repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CC5000 ad:0x40CC5020 ad:0x40CC5040 ad:0x40CC5060 ad:0x40CC5080 ad:0x40CC50A0 ad:0x40CC50C0 ad:0x40CC50E0 ad:0x40CC5100 ad:0x40CC5120 ad:0x40CC5140 ad:0x40CC5160 ad:0x40CC5180 ad:0x40CC51A0 ad:0x40CC51C0 ad:0x40CC51E0) tree "OSCPLL[$1]" base $2 group.long ($2)++0xB line.long 0x0 "OSCPLL_DIRECT,Clock source direct control" bitfld.long 0x0 0. "ON,turn on clock source" "0: OSCPLL is OFF,1: OSCPLL is ON" line.long 0x4 "OSCPLL_DOMAIN,Clock source domain control" bitfld.long 0x4 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 16.--18. "LEVEL0,Dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0x8 "OSCPLL_SETPOINT,Clock source Setpoint setting" hexmask.long.word 0x8 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0x8 0.--15. 1. "SETPOINT,Setpoint" rgroup.long ($2+0x10)++0xB line.long 0x0 "OSCPLL_STATUS0,Clock source working status" bitfld.long 0x0 28. "IN_USE,In use" "0: Clock source is not being used by clock roots,1: Clock source is being used by clock roots" newline hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock source" newline bitfld.long 0x0 5. "STATUS_LATE,Clock source ready" "0: Clock source is not ready to use,1: Clock source is ready to use" newline bitfld.long 0x0 4. "STATUS_EARLY,Clock source active" "0: Clock source is not active,1: Clock source is active" newline bitfld.long 0x0 0. "ON,Clock source current state" "0: Clock source is OFF,1: Clock source is ON" line.long 0x4 "OSCPLL_STATUS1,Clock source low power status" bitfld.long 0x4 31. "STANDBY_OUT_REQUEST,Clock gate turn on request from GPC standby" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 30. "STANDBY_OUT_DONE,Clock gate turn on finish from GPC standby" "0: Request to turn on Clock gate is not complete,1: Request to turn on Clock gate is complete" newline bitfld.long 0x4 29. "STANDBY_IN_DONE,Clock source turn off finish from GPC standby" "0: Clock source is not turned off,1: Clock source is turned off" newline bitfld.long 0x4 28. "STANDBY_IN_REQUEST,Clock gate turn off request from GPC standby" "0: No request,1: Clock gate requested to be turned off" newline bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: No request,1: Request to turn on clock gate" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock source turn off finish from GPC Setpoint" "0: Clock source is not turned off,1: Clock source is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "OSCPLL_CONFIG,Clock source configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." newline bitfld.long 0x8 1. "AUTOMODE_PRESENT,Automode Present" "0: Not present,1: Present" group.long ($2+0x1C)++0x3 line.long 0x0 "OSCPLL_AUTHEN,Clock source access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: PLL does not function in Low power Mode,1: PLL functions in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,LPCG works in Setpoint controlled Mode." "0,1" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." tree.end repeat.end repeat 13. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C)(list ad:0x40CC5200 ad:0x40CC5220 ad:0x40CC5240 ad:0x40CC5260 ad:0x40CC5280 ad:0x40CC52A0 ad:0x40CC52C0 ad:0x40CC52E0 ad:0x40CC5300 ad:0x40CC5320 ad:0x40CC5340 ad:0x40CC5360 ad:0x40CC5380) tree "OSCPLL[$1]" base $2 group.long ($2)++0xB line.long 0x0 "OSCPLL_DIRECT,Clock source direct control" bitfld.long 0x0 0. "ON,turn on clock source" "0: OSCPLL is OFF,1: OSCPLL is ON" line.long 0x4 "OSCPLL_DOMAIN,Clock source domain control" bitfld.long 0x4 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 16.--18. "LEVEL0,Dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0x8 "OSCPLL_SETPOINT,Clock source Setpoint setting" hexmask.long.word 0x8 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0x8 0.--15. 1. "SETPOINT,Setpoint" rgroup.long ($2+0x10)++0xB line.long 0x0 "OSCPLL_STATUS0,Clock source working status" bitfld.long 0x0 28. "IN_USE,In use" "0: Clock source is not being used by clock roots,1: Clock source is being used by clock roots" newline hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock source" newline bitfld.long 0x0 5. "STATUS_LATE,Clock source ready" "0: Clock source is not ready to use,1: Clock source is ready to use" newline bitfld.long 0x0 4. "STATUS_EARLY,Clock source active" "0: Clock source is not active,1: Clock source is active" newline bitfld.long 0x0 0. "ON,Clock source current state" "0: Clock source is OFF,1: Clock source is ON" line.long 0x4 "OSCPLL_STATUS1,Clock source low power status" bitfld.long 0x4 31. "STANDBY_OUT_REQUEST,Clock gate turn on request from GPC standby" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 30. "STANDBY_OUT_DONE,Clock gate turn on finish from GPC standby" "0: Request to turn on Clock gate is not complete,1: Request to turn on Clock gate is complete" newline bitfld.long 0x4 29. "STANDBY_IN_DONE,Clock source turn off finish from GPC standby" "0: Clock source is not turned off,1: Clock source is turned off" newline bitfld.long 0x4 28. "STANDBY_IN_REQUEST,Clock gate turn off request from GPC standby" "0: No request,1: Clock gate requested to be turned off" newline bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: No request,1: Request to turn on clock gate" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock source turn off finish from GPC Setpoint" "0: Clock source is not turned off,1: Clock source is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "OSCPLL_CONFIG,Clock source configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." newline bitfld.long 0x8 1. "AUTOMODE_PRESENT,Automode Present" "0: Not present,1: Present" group.long ($2+0x1C)++0x3 line.long 0x0 "OSCPLL_AUTHEN,Clock source access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: PLL does not function in Low power Mode,1: PLL functions in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,LPCG works in Setpoint controlled Mode." "0,1" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode.,1: Clock works in Domain Mode." newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." tree.end repeat.end base ad:0x40CC0000 group.long 0x6000++0x7 line.long 0x0 "LPCG0_DIRECT,LPCG direct control" bitfld.long 0x0 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG0_DOMAIN,LPCG domain control" bitfld.long 0x4 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x4 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6010++0xB line.long 0x0 "LPCG0_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG0_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG0_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x601C++0xB line.long 0x0 "LPCG0_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG1_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG1_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6030++0xB line.long 0x0 "LPCG1_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG1_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG1_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x603C++0xF line.long 0x0 "LPCG1_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG2_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG2_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG2_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6050++0xB line.long 0x0 "LPCG2_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG2_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG2_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x605C++0xF line.long 0x0 "LPCG2_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG3_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG3_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG3_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6070++0xB line.long 0x0 "LPCG3_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG3_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG3_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x607C++0xF line.long 0x0 "LPCG3_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG4_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG4_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG4_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6090++0xB line.long 0x0 "LPCG4_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG4_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG4_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x609C++0xF line.long 0x0 "LPCG4_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG5_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG5_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG5_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x60B0++0xB line.long 0x0 "LPCG5_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG5_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG5_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x60BC++0xF line.long 0x0 "LPCG5_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG6_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG6_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG6_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x60D0++0xB line.long 0x0 "LPCG6_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG6_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG6_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x60DC++0xF line.long 0x0 "LPCG6_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG7_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG7_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG7_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x60F0++0xB line.long 0x0 "LPCG7_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG7_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG7_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x60FC++0xF line.long 0x0 "LPCG7_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG8_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG8_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG8_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6110++0xB line.long 0x0 "LPCG8_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG8_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG8_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x611C++0xF line.long 0x0 "LPCG8_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG9_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG9_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG9_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6130++0xB line.long 0x0 "LPCG9_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG9_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG9_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x613C++0xF line.long 0x0 "LPCG9_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG10_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG10_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG10_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6150++0xB line.long 0x0 "LPCG10_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG10_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG10_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x615C++0xF line.long 0x0 "LPCG10_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG11_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG11_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG11_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6170++0xB line.long 0x0 "LPCG11_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG11_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG11_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x617C++0xF line.long 0x0 "LPCG11_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG12_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG12_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG12_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6190++0xB line.long 0x0 "LPCG12_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG12_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG12_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x619C++0xB line.long 0x0 "LPCG12_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG13_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG13_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x61B0++0xB line.long 0x0 "LPCG13_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG13_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG13_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x61BC++0xF line.long 0x0 "LPCG13_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG14_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG14_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG14_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x61D0++0xB line.long 0x0 "LPCG14_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG14_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG14_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x61DC++0xF line.long 0x0 "LPCG14_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG15_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG15_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG15_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x61F0++0xB line.long 0x0 "LPCG15_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG15_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG15_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x61FC++0xF line.long 0x0 "LPCG15_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG16_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG16_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG16_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6210++0xB line.long 0x0 "LPCG16_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG16_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG16_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x621C++0xF line.long 0x0 "LPCG16_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG17_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG17_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG17_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6230++0xB line.long 0x0 "LPCG17_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG17_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG17_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x623C++0xF line.long 0x0 "LPCG17_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG18_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG18_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG18_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6250++0xB line.long 0x0 "LPCG18_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG18_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG18_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x625C++0xF line.long 0x0 "LPCG18_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG19_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG19_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG19_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6270++0xB line.long 0x0 "LPCG19_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG19_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG19_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x627C++0xB line.long 0x0 "LPCG19_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG20_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG20_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6290++0xB line.long 0x0 "LPCG20_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG20_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG20_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x629C++0xB line.long 0x0 "LPCG20_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG21_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG21_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x62B0++0xB line.long 0x0 "LPCG21_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG21_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG21_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x62BC++0xB line.long 0x0 "LPCG21_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG22_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG22_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x62D0++0xB line.long 0x0 "LPCG22_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG22_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG22_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x62DC++0xB line.long 0x0 "LPCG22_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG23_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG23_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x62F0++0xB line.long 0x0 "LPCG23_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG23_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG23_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x62FC++0xF line.long 0x0 "LPCG23_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG24_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG24_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG24_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6310++0xB line.long 0x0 "LPCG24_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG24_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG24_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x631C++0xF line.long 0x0 "LPCG24_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG25_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG25_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG25_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6330++0xB line.long 0x0 "LPCG25_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG25_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG25_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x633C++0xF line.long 0x0 "LPCG25_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG26_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG26_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG26_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6350++0xB line.long 0x0 "LPCG26_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG26_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG26_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x635C++0xF line.long 0x0 "LPCG26_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG27_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG27_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG27_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6370++0xB line.long 0x0 "LPCG27_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG27_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG27_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x637C++0xF line.long 0x0 "LPCG27_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG28_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG28_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG28_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6390++0xB line.long 0x0 "LPCG28_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG28_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG28_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x639C++0xF line.long 0x0 "LPCG28_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG29_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG29_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG29_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x63B0++0xB line.long 0x0 "LPCG29_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG29_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG29_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x63BC++0xF line.long 0x0 "LPCG29_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG30_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG30_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG30_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x63D0++0xB line.long 0x0 "LPCG30_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG30_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG30_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x63DC++0xF line.long 0x0 "LPCG30_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG31_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG31_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG31_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x63F0++0xB line.long 0x0 "LPCG31_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG31_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG31_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x63FC++0xF line.long 0x0 "LPCG31_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG32_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG32_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG32_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6410++0xB line.long 0x0 "LPCG32_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG32_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG32_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x641C++0xF line.long 0x0 "LPCG32_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG33_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG33_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG33_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6430++0xB line.long 0x0 "LPCG33_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG33_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG33_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x643C++0xF line.long 0x0 "LPCG33_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG34_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG34_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG34_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6450++0xB line.long 0x0 "LPCG34_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG34_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG34_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x645C++0xF line.long 0x0 "LPCG34_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG35_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG35_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG35_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6470++0xB line.long 0x0 "LPCG35_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG35_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG35_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x647C++0xF line.long 0x0 "LPCG35_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG36_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG36_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG36_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6490++0xB line.long 0x0 "LPCG36_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG36_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG36_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x649C++0xF line.long 0x0 "LPCG36_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG37_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG37_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG37_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x64B0++0xB line.long 0x0 "LPCG37_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG37_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG37_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x64BC++0xF line.long 0x0 "LPCG37_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG38_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG38_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG38_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x64D0++0xB line.long 0x0 "LPCG38_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG38_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG38_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x64DC++0xF line.long 0x0 "LPCG38_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG39_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG39_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG39_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x64F0++0xB line.long 0x0 "LPCG39_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG39_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG39_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x64FC++0xF line.long 0x0 "LPCG39_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG40_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG40_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG40_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6510++0xB line.long 0x0 "LPCG40_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG40_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG40_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x651C++0xB line.long 0x0 "LPCG40_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG41_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG41_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6530++0xB line.long 0x0 "LPCG41_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG41_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG41_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x653C++0xB line.long 0x0 "LPCG41_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG42_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG42_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6550++0xB line.long 0x0 "LPCG42_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG42_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG42_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x655C++0xF line.long 0x0 "LPCG42_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG43_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG43_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG43_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6570++0xB line.long 0x0 "LPCG43_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG43_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG43_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x657C++0xF line.long 0x0 "LPCG43_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG44_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG44_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG44_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6590++0xB line.long 0x0 "LPCG44_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG44_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG44_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x659C++0xF line.long 0x0 "LPCG44_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG45_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG45_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG45_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x65B0++0xB line.long 0x0 "LPCG45_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG45_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG45_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x65BC++0xF line.long 0x0 "LPCG45_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG46_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG46_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG46_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x65D0++0xB line.long 0x0 "LPCG46_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG46_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG46_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x65DC++0xF line.long 0x0 "LPCG46_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG47_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG47_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG47_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x65F0++0xB line.long 0x0 "LPCG47_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG47_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG47_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x65FC++0xF line.long 0x0 "LPCG47_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG48_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG48_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" line.long 0xC "LPCG48_SETPOINT,LPCG Setpoint setting" hexmask.long.word 0xC 16.--31. 1. "STANDBY,Standby" newline hexmask.long.word 0xC 0.--15. 1. "SETPOINT,Setpoints" rgroup.long 0x6610++0xB line.long 0x0 "LPCG48_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG48_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG48_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x661C++0xB line.long 0x0 "LPCG48_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG49_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG49_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6630++0xB line.long 0x0 "LPCG49_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG49_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG49_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x663C++0xB line.long 0x0 "LPCG49_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG50_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG50_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6650++0xB line.long 0x0 "LPCG50_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG50_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG50_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x665C++0xB line.long 0x0 "LPCG50_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG51_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG51_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6670++0xB line.long 0x0 "LPCG51_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG51_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG51_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x667C++0xB line.long 0x0 "LPCG51_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG52_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG52_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6690++0xB line.long 0x0 "LPCG52_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG52_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG52_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x669C++0xB line.long 0x0 "LPCG52_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG53_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG53_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x66B0++0xB line.long 0x0 "LPCG53_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG53_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG53_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x66BC++0xB line.long 0x0 "LPCG53_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG54_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG54_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x66D0++0xB line.long 0x0 "LPCG54_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG54_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG54_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x66DC++0xB line.long 0x0 "LPCG54_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG55_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG55_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x66F0++0xB line.long 0x0 "LPCG55_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG55_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG55_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x66FC++0xB line.long 0x0 "LPCG55_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG56_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG56_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6710++0xB line.long 0x0 "LPCG56_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG56_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG56_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x671C++0xB line.long 0x0 "LPCG56_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG57_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG57_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6730++0xB line.long 0x0 "LPCG57_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG57_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG57_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x673C++0xB line.long 0x0 "LPCG57_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG58_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG58_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6750++0xB line.long 0x0 "LPCG58_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG58_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG58_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x675C++0xB line.long 0x0 "LPCG58_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG59_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG59_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6770++0xB line.long 0x0 "LPCG59_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG59_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG59_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x677C++0xB line.long 0x0 "LPCG59_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG60_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG60_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6790++0xB line.long 0x0 "LPCG60_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG60_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG60_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x679C++0xB line.long 0x0 "LPCG60_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG61_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG61_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x67B0++0xB line.long 0x0 "LPCG61_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG61_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG61_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x67BC++0xB line.long 0x0 "LPCG61_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG62_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG62_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x67D0++0xB line.long 0x0 "LPCG62_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG62_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG62_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x67DC++0xB line.long 0x0 "LPCG62_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG63_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG63_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x67F0++0xB line.long 0x0 "LPCG63_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG63_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG63_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x67FC++0xB line.long 0x0 "LPCG63_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG64_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG64_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6810++0xB line.long 0x0 "LPCG64_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG64_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG64_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x681C++0xB line.long 0x0 "LPCG64_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG65_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG65_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6830++0xB line.long 0x0 "LPCG65_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG65_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG65_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x683C++0xB line.long 0x0 "LPCG65_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG66_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG66_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6850++0xB line.long 0x0 "LPCG66_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG66_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG66_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x685C++0xB line.long 0x0 "LPCG66_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG67_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG67_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6870++0xB line.long 0x0 "LPCG67_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG67_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG67_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x687C++0xB line.long 0x0 "LPCG67_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG68_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG68_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6890++0xB line.long 0x0 "LPCG68_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG68_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG68_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x689C++0xB line.long 0x0 "LPCG68_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG69_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG69_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x68B0++0xB line.long 0x0 "LPCG69_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG69_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG69_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x68BC++0xB line.long 0x0 "LPCG69_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG70_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG70_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x68D0++0xB line.long 0x0 "LPCG70_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG70_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG70_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x68DC++0xB line.long 0x0 "LPCG70_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG71_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG71_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x68F0++0xB line.long 0x0 "LPCG71_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG71_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG71_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x68FC++0xB line.long 0x0 "LPCG71_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG72_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG72_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6910++0xB line.long 0x0 "LPCG72_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG72_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG72_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x691C++0xB line.long 0x0 "LPCG72_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG73_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG73_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6930++0xB line.long 0x0 "LPCG73_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG73_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG73_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x693C++0xB line.long 0x0 "LPCG73_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG74_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG74_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6950++0xB line.long 0x0 "LPCG74_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG74_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG74_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x695C++0xB line.long 0x0 "LPCG74_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG75_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG75_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6970++0xB line.long 0x0 "LPCG75_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG75_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG75_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x697C++0xB line.long 0x0 "LPCG75_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG76_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG76_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6990++0xB line.long 0x0 "LPCG76_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG76_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG76_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x699C++0xB line.long 0x0 "LPCG76_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG77_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG77_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x69B0++0xB line.long 0x0 "LPCG77_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG77_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG77_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x69BC++0xB line.long 0x0 "LPCG77_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG78_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG78_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x69D0++0xB line.long 0x0 "LPCG78_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG78_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG78_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x69DC++0xB line.long 0x0 "LPCG78_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG79_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG79_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x69F0++0xB line.long 0x0 "LPCG79_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG79_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG79_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x69FC++0xB line.long 0x0 "LPCG79_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG80_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG80_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6A10++0xB line.long 0x0 "LPCG80_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG80_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG80_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6A1C++0xB line.long 0x0 "LPCG80_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG81_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG81_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6A30++0xB line.long 0x0 "LPCG81_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG81_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG81_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6A3C++0xB line.long 0x0 "LPCG81_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG82_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG82_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6A50++0xB line.long 0x0 "LPCG82_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG82_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG82_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6A5C++0xB line.long 0x0 "LPCG82_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG83_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG83_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6A70++0xB line.long 0x0 "LPCG83_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG83_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG83_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6A7C++0xB line.long 0x0 "LPCG83_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG84_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG84_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6A90++0xB line.long 0x0 "LPCG84_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG84_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG84_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6A9C++0xB line.long 0x0 "LPCG84_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG85_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG85_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6AB0++0xB line.long 0x0 "LPCG85_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG85_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG85_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6ABC++0xB line.long 0x0 "LPCG85_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG86_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG86_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6AD0++0xB line.long 0x0 "LPCG86_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG86_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG86_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6ADC++0xB line.long 0x0 "LPCG86_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG87_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG87_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6AF0++0xB line.long 0x0 "LPCG87_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG87_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG87_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6AFC++0xB line.long 0x0 "LPCG87_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG88_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG88_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6B10++0xB line.long 0x0 "LPCG88_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG88_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG88_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6B1C++0xB line.long 0x0 "LPCG88_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG89_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG89_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6B30++0xB line.long 0x0 "LPCG89_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG89_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG89_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6B3C++0xB line.long 0x0 "LPCG89_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG90_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG90_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6B50++0xB line.long 0x0 "LPCG90_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG90_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG90_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6B5C++0xB line.long 0x0 "LPCG90_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG91_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG91_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6B70++0xB line.long 0x0 "LPCG91_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG91_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG91_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6B7C++0xB line.long 0x0 "LPCG91_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG92_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG92_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6B90++0xB line.long 0x0 "LPCG92_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG92_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG92_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6B9C++0xB line.long 0x0 "LPCG92_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG93_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG93_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6BB0++0xB line.long 0x0 "LPCG93_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG93_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG93_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6BBC++0xB line.long 0x0 "LPCG93_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG94_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG94_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6BD0++0xB line.long 0x0 "LPCG94_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG94_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG94_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6BDC++0xB line.long 0x0 "LPCG94_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG95_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG95_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6BF0++0xB line.long 0x0 "LPCG95_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG95_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG95_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6BFC++0xB line.long 0x0 "LPCG95_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG96_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG96_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6C10++0xB line.long 0x0 "LPCG96_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG96_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG96_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6C1C++0xB line.long 0x0 "LPCG96_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG97_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG97_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6C30++0xB line.long 0x0 "LPCG97_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG97_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG97_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6C3C++0xB line.long 0x0 "LPCG97_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG98_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG98_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6C50++0xB line.long 0x0 "LPCG98_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG98_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG98_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6C5C++0xB line.long 0x0 "LPCG98_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG99_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG99_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6C70++0xB line.long 0x0 "LPCG99_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG99_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG99_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6C7C++0xB line.long 0x0 "LPCG99_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG100_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG100_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6C90++0xB line.long 0x0 "LPCG100_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG100_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG100_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6C9C++0xB line.long 0x0 "LPCG100_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG101_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG101_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6CB0++0xB line.long 0x0 "LPCG101_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG101_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG101_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6CBC++0xB line.long 0x0 "LPCG101_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG102_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG102_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6CD0++0xB line.long 0x0 "LPCG102_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG102_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG102_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6CDC++0xB line.long 0x0 "LPCG102_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG103_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG103_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6CF0++0xB line.long 0x0 "LPCG103_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG103_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG103_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6CFC++0xB line.long 0x0 "LPCG103_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG104_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG104_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6D10++0xB line.long 0x0 "LPCG104_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG104_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG104_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6D1C++0xB line.long 0x0 "LPCG104_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG105_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG105_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6D30++0xB line.long 0x0 "LPCG105_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG105_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG105_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6D3C++0xB line.long 0x0 "LPCG105_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG106_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG106_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6D50++0xB line.long 0x0 "LPCG106_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG106_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG106_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6D5C++0xB line.long 0x0 "LPCG106_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG107_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG107_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6D70++0xB line.long 0x0 "LPCG107_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG107_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG107_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6D7C++0xB line.long 0x0 "LPCG107_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG108_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG108_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6D90++0xB line.long 0x0 "LPCG108_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG108_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG108_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6D9C++0xB line.long 0x0 "LPCG108_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG109_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG109_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6DB0++0xB line.long 0x0 "LPCG109_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG109_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG109_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6DBC++0xB line.long 0x0 "LPCG109_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG110_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG110_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6DD0++0xB line.long 0x0 "LPCG110_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG110_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG110_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6DDC++0xB line.long 0x0 "LPCG110_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG111_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG111_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6DF0++0xB line.long 0x0 "LPCG111_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG111_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG111_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6DFC++0xB line.long 0x0 "LPCG111_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG112_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG112_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6E10++0xB line.long 0x0 "LPCG112_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG112_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG112_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6E1C++0xB line.long 0x0 "LPCG112_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG113_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG113_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6E30++0xB line.long 0x0 "LPCG113_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG113_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG113_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6E3C++0xB line.long 0x0 "LPCG113_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG114_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG114_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6E50++0xB line.long 0x0 "LPCG114_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG114_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG114_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6E5C++0xB line.long 0x0 "LPCG114_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG115_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG115_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6E70++0xB line.long 0x0 "LPCG115_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG115_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG115_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6E7C++0xB line.long 0x0 "LPCG115_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG116_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG116_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6E90++0xB line.long 0x0 "LPCG116_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG116_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG116_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6E9C++0xB line.long 0x0 "LPCG116_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG117_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG117_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6EB0++0xB line.long 0x0 "LPCG117_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG117_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG117_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6EBC++0xB line.long 0x0 "LPCG117_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG118_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG118_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6ED0++0xB line.long 0x0 "LPCG118_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG118_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG118_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6EDC++0xB line.long 0x0 "LPCG118_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG119_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG119_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6EF0++0xB line.long 0x0 "LPCG119_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG119_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG119_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6EFC++0xB line.long 0x0 "LPCG119_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG120_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG120_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6F10++0xB line.long 0x0 "LPCG120_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG120_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG120_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6F1C++0xB line.long 0x0 "LPCG120_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG121_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG121_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6F30++0xB line.long 0x0 "LPCG121_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG121_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG121_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6F3C++0xB line.long 0x0 "LPCG121_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG122_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG122_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6F50++0xB line.long 0x0 "LPCG122_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG122_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG122_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6F5C++0xB line.long 0x0 "LPCG122_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG123_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG123_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6F70++0xB line.long 0x0 "LPCG123_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG123_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG123_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6F7C++0xB line.long 0x0 "LPCG123_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG124_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG124_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6F90++0xB line.long 0x0 "LPCG124_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG124_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG124_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6F9C++0xB line.long 0x0 "LPCG124_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG125_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG125_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6FB0++0xB line.long 0x0 "LPCG125_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG125_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG125_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6FBC++0xB line.long 0x0 "LPCG125_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG126_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG126_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6FD0++0xB line.long 0x0 "LPCG126_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG126_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG126_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6FDC++0xB line.long 0x0 "LPCG126_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG127_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG127_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x6FF0++0xB line.long 0x0 "LPCG127_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG127_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG127_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x6FFC++0xB line.long 0x0 "LPCG127_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG128_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG128_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7010++0xB line.long 0x0 "LPCG128_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG128_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG128_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x701C++0xB line.long 0x0 "LPCG128_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG129_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG129_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7030++0xB line.long 0x0 "LPCG129_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG129_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG129_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x703C++0xB line.long 0x0 "LPCG129_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG130_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG130_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7050++0xB line.long 0x0 "LPCG130_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG130_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG130_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x705C++0xB line.long 0x0 "LPCG130_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG131_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG131_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7070++0xB line.long 0x0 "LPCG131_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG131_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG131_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x707C++0xB line.long 0x0 "LPCG131_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG132_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG132_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7090++0xB line.long 0x0 "LPCG132_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG132_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG132_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x709C++0xB line.long 0x0 "LPCG132_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG133_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG133_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x70B0++0xB line.long 0x0 "LPCG133_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG133_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG133_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x70BC++0xB line.long 0x0 "LPCG133_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG134_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG134_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x70D0++0xB line.long 0x0 "LPCG134_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG134_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG134_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x70DC++0xB line.long 0x0 "LPCG134_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG135_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG135_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x70F0++0xB line.long 0x0 "LPCG135_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG135_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG135_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x70FC++0xB line.long 0x0 "LPCG135_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG136_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG136_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7110++0xB line.long 0x0 "LPCG136_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG136_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG136_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x711C++0xB line.long 0x0 "LPCG136_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." line.long 0x4 "LPCG137_DIRECT,LPCG direct control" bitfld.long 0x4 0. "ON,LPCG on" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x8 "LPCG137_DOMAIN,LPCG domain control" bitfld.long 0x8 28.--30. "LEVEL3,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 24.--26. "LEVEL2,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 20.--22. "LEVEL1,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 16.--18. "LEVEL0,Depend level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" newline bitfld.long 0x8 0.--2. "LEVEL,Current dependence level" "0: This clock source is not needed in any mode and..,1: This clock source is needed in RUN mode but not..,2: This clock source is needed in RUN and WAIT mode..,3: This clock source is needed in RUN WAIT and STOP..,4: This clock source is always on in any mode..,?,?,?" rgroup.long 0x7130++0xB line.long 0x0 "LPCG137_STATUS0,LPCG working status" hexmask.long.byte 0x0 12.--15. 1. "DOMAIN_ENABLE,Enable status from each domain" newline hexmask.long.byte 0x0 8.--11. 1. "ACTIVE_DOMAIN,Domains that own this clock gate" newline bitfld.long 0x0 0. "ON,LPCG current state" "0: LPCG is OFF.,1: LPCG is ON." line.long 0x4 "LPCG137_STATUS1,LPCG low power status" bitfld.long 0x4 27. "SETPOINT_ON_DONE,Clock gate turn on finish from GPC Setpoint" "0: Clock gate is not turned on,1: Clock gate is turned on" newline bitfld.long 0x4 26. "SETPOINT_ON_REQUEST,Clock gate turn on request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned on" newline bitfld.long 0x4 25. "SETPOINT_OFF_DONE,Clock gate turn off finish from GPC Setpoint" "0: Clock gate is not turned off,1: Clock gate is turned off" newline bitfld.long 0x4 24. "SETPOINT_OFF_REQUEST,Clock gate turn off request from GPC Setpoint" "0: No request,1: Clock gate requested to be turned off" newline hexmask.long.byte 0x4 20.--23. 1. "CURRENT_SETPOINT,Current Setpoint" newline hexmask.long.byte 0x4 16.--19. 1. "TARGET_SETPOINT,Next Setpoint to change to" newline bitfld.long 0x4 15. "CPU3_MODE_DONE,Domain3 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 14. "CPU3_MODE_REQUEST,Domain3 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 12.--13. "CPU3_MODE,Domain3 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 11. "CPU2_MODE_DONE,Domain2 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 10. "CPU2_MODE_REQUEST,Domain2 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 8.--9. "CPU2_MODE,Domain2 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 7. "CPU1_MODE_DONE,Domain1 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 6. "CPU1_MODE_REQUEST,Domain1 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 4.--5. "CPU1_MODE,Domain1 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" newline bitfld.long 0x4 3. "CPU0_MODE_DONE,Domain0 Low Power Mode task done" "0: Clock is not gated,1: Clock is gated-off" newline bitfld.long 0x4 2. "CPU0_MODE_REQUEST,Domain0 request enter Low Power Mode" "0: No request,1: Request from domain to enter Low Power Mode" newline bitfld.long 0x4 0.--1. "CPU0_MODE,Domain0 Low Power Mode" "0: Run,1: Wait,2: Stop,3: Suspend" line.long 0x8 "LPCG137_CONFIG,LPCG configuration" bitfld.long 0x8 4. "SETPOINT_PRESENT,Setpoint present" "0: Setpoint is not implemented.,1: Setpoint is implemented." group.long 0x713C++0x3 line.long 0x0 "LPCG137_AUTHEN,LPCG access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." newline bitfld.long 0x0 18. "CPULPM,CPU Low Power Mode" "0: LPCG is not functioning in Low power Mode,1: LPCG is functioning in Low Power Mode" newline bitfld.long 0x0 17. "SETPOINT_MODE,Low power and access control by Setpoint" "0: LPCG is not functioning in Setpoint controlled..,1: LPCG is functioning in Setpoint controlled Mode" newline bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in Domain Mode,1: Clock works in Domain Mode" newline bitfld.long 0x0 12. "LOCK_LIST,Lock Whitelist" "0: Whitelist is not locked.,1: Whitelist is locked." newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Whitelist" newline bitfld.long 0x0 4. "LOCK_TZ,lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." newline bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: LPCG cannot be changed in user mode.,1: LPCG can be changed in user mode." tree.end tree "CCM_OBS" base ad:0x40150000 repeat 6. (list 0x0 0x1 0x2 0x3 0x4 0x5)(list ad:0x40150000 ad:0x40150080 ad:0x40150100 ad:0x40150180 ad:0x40150200 ad:0x40150280) tree "OBSERVE[$1]" base $2 group.long ($2)++0xF line.long 0x0 "OBSERVE_CONTROL,Observe control" bitfld.long 0x0 24. "OFF,Turn off" "0: observe slice is on,1: observe slice is off" hexmask.long.byte 0x0 16.--23. 1. "DIVIDE,Divider for observe signal" newline bitfld.long 0x0 15. "RESET,Reset observe divider" "0: No reset,1: Reset observe divider" bitfld.long 0x0 13. "INV,Invert" "0: Clock phase remain same.,1: Invert clock phase before measurement or send to.." newline bitfld.long 0x0 12. "RAW,Observe raw signal" "0: Select divided signal.,1: Select raw signal." hexmask.long.word 0x0 0.--8. 1. "SELECT,Observe signal selector" line.long 0x4 "OBSERVE_CONTROL_SET,Observe control" bitfld.long 0x4 24. "OFF,Turn off" "0,1" hexmask.long.byte 0x4 16.--23. 1. "DIVIDE,Divider for observe signal" newline bitfld.long 0x4 15. "RESET,Reset observe divider" "0,1" bitfld.long 0x4 13. "INV,Invert" "0,1" newline bitfld.long 0x4 12. "RAW,Observe raw signal" "0,1" hexmask.long.word 0x4 0.--8. 1. "SELECT,Observe signal selector" line.long 0x8 "OBSERVE_CONTROL_CLR,Observe control" eventfld.long 0x8 24. "OFF,Turn off" "0,1" hexmask.long.byte 0x8 16.--23. 1. "DIVIDE,Divider for observe signal" newline eventfld.long 0x8 15. "RESET,Reset observe divider" "0,1" eventfld.long 0x8 13. "INV,Invert" "0,1" newline eventfld.long 0x8 12. "RAW,Observe raw signal" "0,1" hexmask.long.word 0x8 0.--8. 1. "SELECT,Observe signal selector" line.long 0xC "OBSERVE_CONTROL_TOG,Observe control" bitfld.long 0xC 24. "OFF,Turn off" "0,1" hexmask.long.byte 0xC 16.--23. 1. "DIVIDE,Divider for observe signal" newline bitfld.long 0xC 15. "RESET,Reset observe divider" "0,1" bitfld.long 0xC 13. "INV,Invert" "0,1" newline bitfld.long 0xC 12. "RAW,Observe raw signal" "0,1" hexmask.long.word 0xC 0.--8. 1. "SELECT,Observe signal selector" rgroup.long ($2+0x20)++0x3 line.long 0x0 "OBSERVE_STATUS0,Observe status" bitfld.long 0x0 24. "OFF,Turn off slice" "0: observe slice is on,1: observe slice is off" hexmask.long.byte 0x0 16.--23. 1. "DIVIDE,Divide value status. The clock will be divided by DIVIDE + 1." newline bitfld.long 0x0 15. "RESET,Reset state" "0: Observe divider is not in reset state,1: Observe divider is in reset state" bitfld.long 0x0 13. "INV,Polarity of the observe target" "0: Polarity is not inverted,1: Polarity of the observe target is inverted" newline bitfld.long 0x0 12. "RAW,Observe raw signal" "0: Divided signal is selected,1: Raw signal is selected" hexmask.long.word 0x0 0.--8. 1. "SELECT,Select value" group.long ($2+0x30)++0xF line.long 0x0 "OBSERVE_AUTHEN,Observe access control" bitfld.long 0x0 20. "LOCK_MODE,Lock low power and access mode" "0: MODE is not locked.,1: MODE is locked." bitfld.long 0x0 16. "DOMAIN_MODE,Low power and access control by domain" "0: Clock does not work in domain mode.,1: Clock works in domain mode." newline bitfld.long 0x0 12. "LOCK_LIST,Lock white list" "0: White list is not locked.,1: White list is locked." hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,White list" newline bitfld.long 0x0 4. "LOCK_TZ,Lock truszone setting" "0: Trustzone setting is not locked.,1: Trustzone setting is locked." bitfld.long 0x0 1. "TZ_NS,Non-secure access" "0: Cannot be changed in Non-secure mode.,1: Can be changed in Non-secure mode." newline bitfld.long 0x0 0. "TZ_USER,User access" "0: Clock cannot be changed in user mode.,1: Clock can be changed in user mode." line.long 0x4 "OBSERVE_AUTHEN_SET,Observe access control" bitfld.long 0x4 20. "LOCK_MODE,Lock low power and access mode" "0,1" bitfld.long 0x4 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0x4 12. "LOCK_LIST,Lock white list" "0,1" hexmask.long.byte 0x4 8.--11. 1. "WHITE_LIST,White list" newline bitfld.long 0x4 4. "LOCK_TZ,Lock truszone setting" "0,1" bitfld.long 0x4 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0x4 0. "TZ_USER,User access" "0,1" line.long 0x8 "OBSERVE_AUTHEN_CLR,Observe access control" eventfld.long 0x8 20. "LOCK_MODE,Lock low power and access mode" "0,1" eventfld.long 0x8 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline eventfld.long 0x8 12. "LOCK_LIST,Lock white list" "0,1" hexmask.long.byte 0x8 8.--11. 1. "WHITE_LIST,White list" newline eventfld.long 0x8 4. "LOCK_TZ,Lock truszone setting" "0,1" eventfld.long 0x8 1. "TZ_NS,Non-secure access" "0,1" newline eventfld.long 0x8 0. "TZ_USER,User access" "0,1" line.long 0xC "OBSERVE_AUTHEN_TOG,Observe access control" bitfld.long 0xC 20. "LOCK_MODE,Lock low power and access mode" "0,1" bitfld.long 0xC 16. "DOMAIN_MODE,Low power and access control by domain" "0,1" newline bitfld.long 0xC 12. "LOCK_LIST,Lock white list" "0,1" hexmask.long.byte 0xC 8.--11. 1. "WHITE_LIST,White list" newline bitfld.long 0xC 4. "LOCK_TZ,Lock truszone setting" "0,1" bitfld.long 0xC 1. "TZ_NS,Non-secure access" "0,1" newline bitfld.long 0xC 0. "TZ_USER,User access" "0,1" rgroup.long ($2+0x40)++0xB line.long 0x0 "OBSERVE_FREQUENCY_CURRENT,Current frequency detected" hexmask.long 0x0 0.--31. 1. "FREQUENCY,Frequency" line.long 0x4 "OBSERVE_FREQUENCY_MIN,Minimum frequency detected" hexmask.long 0x4 0.--31. 1. "FREQUENCY,Frequency" line.long 0x8 "OBSERVE_FREQUENCY_MAX,Maximum frequency detected" hexmask.long 0x8 0.--31. 1. "FREQUENCY,Frequency" tree.end repeat.end tree.end tree "CDOG" base ad:0x41900000 group.long 0x0++0xB line.long 0x0 "CONTROL,Control" bitfld.long 0x0 30.--31. "DEBUG_HALT_CTRL,DEBUG_HALT control" "?,1: Keep the timer running,2: Stop the timer,?" bitfld.long 0x0 28.--29. "IRQ_PAUSE,IRQ pause control" "?,1: Keep the timer running,2: Stop the timer,?" newline bitfld.long 0x0 17.--19. "ADDRESS_CTRL,ADDRESS fault control" "?,1: Enable reset,2: Enable interrupt,?,4: Disable both reset and interrupt,?,?,?" bitfld.long 0x0 14.--16. "STATE_CTRL,STATE fault control" "?,1: Enable reset,2: Enable interrupt,?,4: Disable both reset and interrupt,?,?,?" newline bitfld.long 0x0 11.--13. "CONTROL_CTRL,CONTROL fault control" "?,1: Enable reset,?,?,4: Disable reset,?,?,?" bitfld.long 0x0 8.--10. "SEQUENCE_CTRL,SEQUENCE fault control" "?,1: Enable reset,2: Enable interrupt,?,4: Disable both reset and interrupt,?,?,?" newline bitfld.long 0x0 5.--7. "MISCOMPARE_CTRL,MISCOMPARE fault control" "?,1: Enable reset,2: Enable interrupt,?,4: Disable both reset and interrupt,?,?,?" bitfld.long 0x0 2.--4. "TIMEOUT_CTRL,TIMEOUT fault control" "?,1: Enable reset,2: Enable interrupt,?,4: Disable both reset and interrupt,?,?,?" newline bitfld.long 0x0 0.--1. "LOCK_CTRL,Lock control" "?,1: Locked,2: Unlocked,?" line.long 0x4 "RELOAD,Instruction Timer reload" hexmask.long 0x4 0.--31. 1. "RLOAD,Instruction Timer reload value" line.long 0x8 "INSTRUCTION_TIMER,Instruction Timer" hexmask.long 0x8 0.--31. 1. "INSTIM,Current value of the Instruction Timer" wgroup.long 0xC++0x3 line.long 0x0 "SECURE_COUNTER,Secure Counter" hexmask.long 0x0 0.--31. 1. "SECCNT,Secure Counter" rgroup.long 0x10++0x7 line.long 0x0 "STATUS,Status 1" hexmask.long.byte 0x0 28.--31. 1. "CURST,Current State" hexmask.long.byte 0x0 16.--23. 1. "NUMILSEQF,Number of SEQUENCE faults since the last POR" newline hexmask.long.byte 0x0 8.--15. 1. "NUMMISCOMPF,Number of MISCOMPARE faults since the last POR" hexmask.long.byte 0x0 0.--7. 1. "NUMTOF,Number of TIMEOUT faults since the last POR" line.long 0x4 "STATUS2,Status 2" hexmask.long.byte 0x4 16.--23. 1. "NUMILLA,Number of ADDRESS faults since the last POR" hexmask.long.byte 0x4 8.--15. 1. "NUMILLSTF,Number of STATE faults since the last POR" newline hexmask.long.byte 0x4 0.--7. 1. "NUMCNTF,Number of CONTROL faults since the last POR" group.long 0x18++0x7 line.long 0x0 "FLAGS,Flags" bitfld.long 0x0 16. "POR_FLAG,Power-on reset flag" "0: A Power-on reset event has not occurred,1: A Power-on reset event has occurred" bitfld.long 0x0 5. "ADDR_FLAG,ADDRESS fault flag" "0: An ADDRESS fault has not occurred,1: An ADDRESS fault has occurred" newline bitfld.long 0x0 4. "STATE_FLAG,STATE fault flag" "0: A STATE fault has not occurred,1: A STATE fault has occurred" bitfld.long 0x0 3. "CNT_FLAG,CONTROL fault flag" "0: A CONTROL fault has not occurred,1: A CONTROL fault has occurred" newline bitfld.long 0x0 2. "SEQ_FLAG,SEQUENCE fault flag" "0: A SEQUENCE fault has not occurred,1: A SEQUENCE fault has occurred" bitfld.long 0x0 1. "MISCOM_FLAG,MISCOMPARE fault flag" "0: A MISCOMPARE fault has not occurred,1: A MISCOMPARE fault has occurred" newline bitfld.long 0x0 0. "TO_FLAG,TIMEOUT fault flag" "0: A TIMEOUT fault has not occurred,1: A TIMEOUT fault has occurred" line.long 0x4 "PERSISTENT,Persistent Data Storage" hexmask.long 0x4 0.--31. 1. "PERSIS,Persistent Storage" wgroup.long 0x20++0x2B line.long 0x0 "START,START Command" hexmask.long 0x0 0.--31. 1. "STRT,Start command" line.long 0x4 "STOP,STOP Command" hexmask.long 0x4 0.--31. 1. "STP,Stop command" line.long 0x8 "RESTART,RESTART Command" hexmask.long 0x8 0.--31. 1. "RSTRT,Restart command" line.long 0xC "ADD,ADD Command" hexmask.long 0xC 0.--31. 1. "AD,ADD Write Value" line.long 0x10 "ADD1,ADD1 Command" hexmask.long 0x10 0.--31. 1. "AD1,ADD 1" line.long 0x14 "ADD16,ADD16 Command" hexmask.long 0x14 0.--31. 1. "AD16,ADD 16" line.long 0x18 "ADD256,ADD256 Command" hexmask.long 0x18 0.--31. 1. "AD256,ADD 256" line.long 0x1C "SUB,SUB Command" hexmask.long 0x1C 0.--31. 1. "S0B,Subtract Write Value" line.long 0x20 "SUB1,SUB1 Command" hexmask.long 0x20 0.--31. 1. "S1B,Subtract 1" line.long 0x24 "SUB16,SUB16 Command" hexmask.long 0x24 0.--31. 1. "SB16,Subtract 16" line.long 0x28 "SUB256,SUB256 Command" hexmask.long 0x28 0.--31. 1. "SB256,Subtract 256" tree.end sif (cpuis("IMXRT1163-CM7")||cpuis("IMXRT1165-CM7")||cpuis("IMXRT1166-CM7")) tree "CM7_MCM" base ad:0xE0080000 group.long 0x10++0x3 line.long 0x0 "ISCR,Interrupt Status and Control Register" bitfld.long 0x0 31. "FIDCE,FPU Input Denormal Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x0 28. "FIXCE,FPU Inexact Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x0 27. "FUFCE,FPU Underflow Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x0 26. "FOFCE,FPU Overflow Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" newline bitfld.long 0x0 25. "FDZCE,FPU Divide-by-Zero Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x0 24. "FIOCE,FPU Invalid Operation Interrupt Enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x0 21. "WABE,TCM Write Abort Interrupt enable" "0: Disable interrupt,1: Enable interrupt" rbitfld.long 0x0 15. "FIDC,FPU Input Denormal Interrupt Status" "0: No interrupt,1: Interrupt occured" newline rbitfld.long 0x0 12. "FIXC,FPU Inexact Interrupt Status" "0: No interrupt,1: Interrupt occured" rbitfld.long 0x0 11. "FUFC,FPU Underflow Interrupt Status" "0: No interrupt,1: Interrupt occured" rbitfld.long 0x0 10. "FOFC,FPU Overflow interrupt status" "0: No interrupt,1: Interrupt occured" rbitfld.long 0x0 9. "FDZC,FPU Divide-by-Zero Interrupt Status" "0: No interrupt,1: Interrupt occured" newline rbitfld.long 0x0 8. "FIOC,FPU Invalid Operation interrupt Status" "0: No interrupt,1: Interrupt occured" rbitfld.long 0x0 6. "WABSO,Write Abort on Slave Overrun" "0: No write abort overrun,1: Write abort overrun occurred" eventfld.long 0x0 5. "WABS,Write Abort on Slave" "0: No abort,1: Abort" tree.end endif tree "CMP" base ad:0x0 tree "CMP1" base ad:0x401A4000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number. This read only field returns the major version number for the module specification." hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number. This read only field returns the minor version number for the module specification." newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number. This read only filed returns the feature set number." line.long 0x4 "PARAM,Parameter Register" hexmask.long 0x4 0.--31. 1. "PARAM,Parameter Registers. This read only filed returns the feature parameters implemented along with the Version ID register." group.long 0x8++0xF line.long 0x0 "C0,CMP Control Register 0" bitfld.long 0x0 31. "LINKEN,CMP to DAC link enable." "0: CMP to DAC link is disabled,1: CMP to DAC link is enabled." bitfld.long 0x0 30. "DMAEN,DMA Enable" "0: DMA is disabled.,1: DMA is enabled." newline bitfld.long 0x0 28. "IER,Comparator Interrupt Enable Rising" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 27. "IEF,Comparator Interrupt Enable Falling" "0: Interrupt is disabled.,1: Interrupt is enabled." newline eventfld.long 0x0 26. "CFR,Analog Comparator Flag Rising" "0: A rising edge has not been detected on COUT.,1: A rising edge on COUT has occurred." eventfld.long 0x0 25. "CFF,Analog Comparator Flag Falling" "0: A falling edge has not been detected on COUT.,1: A falling edge on COUT has occurred." newline rbitfld.long 0x0 24. "COUT,Analog Comparator Output" "0,1" hexmask.long.byte 0x0 16.--23. 1. "FPR,Filter Sample Period" newline bitfld.long 0x0 15. "SE,Sample Enable" "0: Sampling mode is not selected.,1: Sampling mode is selected." bitfld.long 0x0 14. "WE,Windowing Enable" "0: Windowing mode is not selected.,1: Windowing mode is selected." newline bitfld.long 0x0 12. "PMODE,Power Mode Select" "0: Low Speed (LS) comparison mode is selected.,1: High Speed (HS) comparison mode is selected." bitfld.long 0x0 11. "INVT,Comparator invert" "0: Does not invert the comparator output.,1: Inverts the comparator output." newline bitfld.long 0x0 10. "COS,Comparator Output Select" "0: Set CMPO to equal COUT (filtered comparator..,1: Set CMPO to equal COUTA (unfiltered comparator.." bitfld.long 0x0 9. "OPE,Comparator Output Pin Enable" "0: When OPE is 0 the comparator output (after..,1: When OPE is 1 and if the software has configured.." newline bitfld.long 0x0 8. "EN,Comparator Module Enable" "0: Analog Comparator is disabled.,1: Analog Comparator is enabled." bitfld.long 0x0 4.--6. "FILTER_CNT,Filter Sample Count" "0: Filter is disabled. If SE = 1 then COUT is a..,1: 1 consecutive sample must agree (comparator..,2: 2 consecutive samples must agree.,3: 3 consecutive samples must agree.,4: 4 consecutive samples must agree.,5: 5 consecutive samples must agree.,6: 6 consecutive samples must agree.,7: 7 consecutive samples must agree." newline bitfld.long 0x0 0.--1. "HYSTCTR,Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level" "0: The hard block output has level 0 hysteresis..,1: The hard block output has level 1 hysteresis..,2: The hard block output has level 2 hysteresis..,3: The hard block output has level 3 hysteresis.." line.long 0x4 "C1,CMP Control Register 1" bitfld.long 0x4 28.--30. "PSEL,Plus Input MUX Control" "0: Internal Positive Input 0 for Plus Channel --..,1: External Input 1 for Plus Channel -- Reference..,2: External Input 2 for Plus Channel -- Reference..,3: External Input 3 for Plus Channel -- Reference..,4: External Input 4 for Plus Channel -- Reference..,5: External Input 5 for Plus Channel -- Reference..,6: External Input 6 for Plus Channel -- Reference..,7: Internal 8b DAC output" bitfld.long 0x4 24.--26. "MSEL,Minus Input MUX Control" "0: Internal Negative Input 0 for Minus Channel --..,1: External Input 1 for Minus Channel -- Reference..,2: External Input 2 for Minus Channel -- Reference..,3: External Input 3 for Minus Channel -- Reference..,4: External Input 4 for Minus Channel -- Reference..,5: External Input 5 for Minus Channel -- Reference..,6: External Input 6 for Minus Channel -- Reference..,7: Internal 8b DAC output" newline bitfld.long 0x4 21. "CHN5,Channel 5 input enable" "0,1" bitfld.long 0x4 20. "CHN4,Channel 4 input enable" "0,1" newline bitfld.long 0x4 19. "CHN3,Channel 3 input enable" "0,1" bitfld.long 0x4 18. "CHN2,Channel 2 input enable" "0,1" newline bitfld.long 0x4 17. "CHN1,Channel 1 input enable" "0,1" bitfld.long 0x4 16. "CHN0,Channel 0 input enable" "0,1" newline bitfld.long 0x4 10. "DACEN,DAC Enable" "0: DAC is disabled.,1: DAC is enabled." bitfld.long 0x4 9. "VRSEL,Supply Voltage Reference Source Select" "0: Vin1 is selected as resistor ladder network..,1: Vin2 is selected as resistor ladder network.." newline bitfld.long 0x4 8. "DMODE,DAC Mode Selection" "0: DAC is selected to work in low speed and low..,1: DAC is selected to work in high speed high power.." hexmask.long.byte 0x4 0.--7. 1. "VOSEL,DAC Output Voltage Select" line.long 0x8 "C2,CMP Control Register 2" bitfld.long 0x8 30. "RRIE,Round-Robin interrupt enable" "0: The round-robin interrupt is disabled.,1: The round-robin interrupt is enabled when a.." bitfld.long 0x8 29. "FXMP,Fixed MUX Port" "0: The Plus port is fixed. Only the inputs to the..,1: The Minus port is fixed. Only the inputs to the.." newline bitfld.long 0x8 25.--27. "FXMXCH,Fixed channel selection" "0: External Reference Input 0 is selected as the..,1: External Reference Input 1 is selected as the..,2: External Reference Input 2 is selected as the..,3: External Reference Input 3 is selected as the..,4: External Reference Input 4 is selected as the..,5: External Reference Input 5 is selected as the..,?,7: The 8bit DAC is selected as the fixed reference.." eventfld.long 0x8 21. "CH5F,CH5F" "0,1" newline eventfld.long 0x8 20. "CH4F,CH4F" "0,1" eventfld.long 0x8 19. "CH3F,CH3F" "0,1" newline eventfld.long 0x8 18. "CH2F,CH2F" "0,1" eventfld.long 0x8 17. "CH1F,CH1F" "0,1" newline eventfld.long 0x8 16. "CH0F,CH0F" "0,1" bitfld.long 0x8 14.--15. "NSAM,Number of sample clocks" "0: The comparison result is sampled as soon as the..,1: The sampling takes place 1 round-robin clock..,2: The sampling takes place 2 round-robin clock..,3: The sampling takes place 3 round-robin clock.." newline hexmask.long.byte 0x8 8.--13. 1. "INITMOD,Comparator and DAC initialization delay modulus." hexmask.long.byte 0x8 0.--5. 1. "ACOn,ACOn" line.long 0xC "C3,CMP Control Register 3" bitfld.long 0xC 28. "PCHCTEN,Positive Channel Continuous Mode Enable." "0: Positive channel is in Discrete Mode and special..,1: Positive channel is in Continuous Mode and no.." bitfld.long 0xC 24. "NCHCTEN,Negative Channel Continuous Mode Enable." "0: Negative channel is in Discrete Mode and special..,1: Negative channel is in Continuous Mode and no.." newline bitfld.long 0xC 20. "RDIVE,Resistor Divider Enable" "0: The resistor is not enabled even when either..,1: The resistor is enabled because the inputs are.." bitfld.long 0xC 16. "DMCS,Discrete Mode Clock Selection" "0: Slow clock is selected for the timing generation.,1: Fast clock is selected for the timing generation." newline bitfld.long 0xC 12.--14. "ACSAT,Analog Comparator Sampling Time control." "0: The sampling time equals to T,1: The sampling time equasl to 2*T,2: The sampling time equasl to 4*T,3: The sampling time equasl to 8*T,4: The sampling time equasl to 16*T,5: The sampling time equasl to 32*T,6: The sampling time equasl to 64*T,7: The sampling time equasl to 256*T" bitfld.long 0xC 8.--10. "ACPH1TC,Analog Comparator Phase1 Timing Control." "0: Phase1 active time in one sampling period equals..,1: Phase1 active time in one sampling period equals..,2: Phase1 active time in one sampling period equals..,3: Phase1 active time in one sampling period equals..,4: Phase1 active time in one sampling period equals..,5: Phase1 active time in one sampling period equals..,6: Phase1 active time in one sampling period equals..,7: Phase1 active time in one sampling period equals.." newline bitfld.long 0xC 4.--6. "ACPH2TC,Analog Comparator Phase2 Timing Control." "0: Phase2 active time in one sampling period equals..,1: Phase2 active time in one sampling period equals..,2: Phase2 active time in one sampling period equals..,3: Phase2 active time in one sampling period equals..,4: Phase2 active time in one sampling period equals..,5: Phase2 active time in one sampling period equals..,6: Phase2 active time in one sampling period equals..,7: Phase2 active time in one sampling period equals.." tree.end tree "CMP2" base ad:0x401A8000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number. This read only field returns the major version number for the module specification." hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number. This read only field returns the minor version number for the module specification." newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number. This read only filed returns the feature set number." line.long 0x4 "PARAM,Parameter Register" hexmask.long 0x4 0.--31. 1. "PARAM,Parameter Registers. This read only filed returns the feature parameters implemented along with the Version ID register." group.long 0x8++0xF line.long 0x0 "C0,CMP Control Register 0" bitfld.long 0x0 31. "LINKEN,CMP to DAC link enable." "0: CMP to DAC link is disabled,1: CMP to DAC link is enabled." bitfld.long 0x0 30. "DMAEN,DMA Enable" "0: DMA is disabled.,1: DMA is enabled." newline bitfld.long 0x0 28. "IER,Comparator Interrupt Enable Rising" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 27. "IEF,Comparator Interrupt Enable Falling" "0: Interrupt is disabled.,1: Interrupt is enabled." newline eventfld.long 0x0 26. "CFR,Analog Comparator Flag Rising" "0: A rising edge has not been detected on COUT.,1: A rising edge on COUT has occurred." eventfld.long 0x0 25. "CFF,Analog Comparator Flag Falling" "0: A falling edge has not been detected on COUT.,1: A falling edge on COUT has occurred." newline rbitfld.long 0x0 24. "COUT,Analog Comparator Output" "0,1" hexmask.long.byte 0x0 16.--23. 1. "FPR,Filter Sample Period" newline bitfld.long 0x0 15. "SE,Sample Enable" "0: Sampling mode is not selected.,1: Sampling mode is selected." bitfld.long 0x0 14. "WE,Windowing Enable" "0: Windowing mode is not selected.,1: Windowing mode is selected." newline bitfld.long 0x0 12. "PMODE,Power Mode Select" "0: Low Speed (LS) comparison mode is selected.,1: High Speed (HS) comparison mode is selected." bitfld.long 0x0 11. "INVT,Comparator invert" "0: Does not invert the comparator output.,1: Inverts the comparator output." newline bitfld.long 0x0 10. "COS,Comparator Output Select" "0: Set CMPO to equal COUT (filtered comparator..,1: Set CMPO to equal COUTA (unfiltered comparator.." bitfld.long 0x0 9. "OPE,Comparator Output Pin Enable" "0: When OPE is 0 the comparator output (after..,1: When OPE is 1 and if the software has configured.." newline bitfld.long 0x0 8. "EN,Comparator Module Enable" "0: Analog Comparator is disabled.,1: Analog Comparator is enabled." bitfld.long 0x0 4.--6. "FILTER_CNT,Filter Sample Count" "0: Filter is disabled. If SE = 1 then COUT is a..,1: 1 consecutive sample must agree (comparator..,2: 2 consecutive samples must agree.,3: 3 consecutive samples must agree.,4: 4 consecutive samples must agree.,5: 5 consecutive samples must agree.,6: 6 consecutive samples must agree.,7: 7 consecutive samples must agree." newline bitfld.long 0x0 0.--1. "HYSTCTR,Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level" "0: The hard block output has level 0 hysteresis..,1: The hard block output has level 1 hysteresis..,2: The hard block output has level 2 hysteresis..,3: The hard block output has level 3 hysteresis.." line.long 0x4 "C1,CMP Control Register 1" bitfld.long 0x4 28.--30. "PSEL,Plus Input MUX Control" "0: Internal Positive Input 0 for Plus Channel --..,1: External Input 1 for Plus Channel -- Reference..,2: External Input 2 for Plus Channel -- Reference..,3: External Input 3 for Plus Channel -- Reference..,4: External Input 4 for Plus Channel -- Reference..,5: External Input 5 for Plus Channel -- Reference..,6: External Input 6 for Plus Channel -- Reference..,7: Internal 8b DAC output" bitfld.long 0x4 24.--26. "MSEL,Minus Input MUX Control" "0: Internal Negative Input 0 for Minus Channel --..,1: External Input 1 for Minus Channel -- Reference..,2: External Input 2 for Minus Channel -- Reference..,3: External Input 3 for Minus Channel -- Reference..,4: External Input 4 for Minus Channel -- Reference..,5: External Input 5 for Minus Channel -- Reference..,6: External Input 6 for Minus Channel -- Reference..,7: Internal 8b DAC output" newline bitfld.long 0x4 21. "CHN5,Channel 5 input enable" "0,1" bitfld.long 0x4 20. "CHN4,Channel 4 input enable" "0,1" newline bitfld.long 0x4 19. "CHN3,Channel 3 input enable" "0,1" bitfld.long 0x4 18. "CHN2,Channel 2 input enable" "0,1" newline bitfld.long 0x4 17. "CHN1,Channel 1 input enable" "0,1" bitfld.long 0x4 16. "CHN0,Channel 0 input enable" "0,1" newline bitfld.long 0x4 10. "DACEN,DAC Enable" "0: DAC is disabled.,1: DAC is enabled." bitfld.long 0x4 9. "VRSEL,Supply Voltage Reference Source Select" "0: Vin1 is selected as resistor ladder network..,1: Vin2 is selected as resistor ladder network.." newline bitfld.long 0x4 8. "DMODE,DAC Mode Selection" "0: DAC is selected to work in low speed and low..,1: DAC is selected to work in high speed high power.." hexmask.long.byte 0x4 0.--7. 1. "VOSEL,DAC Output Voltage Select" line.long 0x8 "C2,CMP Control Register 2" bitfld.long 0x8 30. "RRIE,Round-Robin interrupt enable" "0: The round-robin interrupt is disabled.,1: The round-robin interrupt is enabled when a.." bitfld.long 0x8 29. "FXMP,Fixed MUX Port" "0: The Plus port is fixed. Only the inputs to the..,1: The Minus port is fixed. Only the inputs to the.." newline bitfld.long 0x8 25.--27. "FXMXCH,Fixed channel selection" "0: External Reference Input 0 is selected as the..,1: External Reference Input 1 is selected as the..,2: External Reference Input 2 is selected as the..,3: External Reference Input 3 is selected as the..,4: External Reference Input 4 is selected as the..,5: External Reference Input 5 is selected as the..,?,7: The 8bit DAC is selected as the fixed reference.." eventfld.long 0x8 21. "CH5F,CH5F" "0,1" newline eventfld.long 0x8 20. "CH4F,CH4F" "0,1" eventfld.long 0x8 19. "CH3F,CH3F" "0,1" newline eventfld.long 0x8 18. "CH2F,CH2F" "0,1" eventfld.long 0x8 17. "CH1F,CH1F" "0,1" newline eventfld.long 0x8 16. "CH0F,CH0F" "0,1" bitfld.long 0x8 14.--15. "NSAM,Number of sample clocks" "0: The comparison result is sampled as soon as the..,1: The sampling takes place 1 round-robin clock..,2: The sampling takes place 2 round-robin clock..,3: The sampling takes place 3 round-robin clock.." newline hexmask.long.byte 0x8 8.--13. 1. "INITMOD,Comparator and DAC initialization delay modulus." hexmask.long.byte 0x8 0.--5. 1. "ACOn,ACOn" line.long 0xC "C3,CMP Control Register 3" bitfld.long 0xC 28. "PCHCTEN,Positive Channel Continuous Mode Enable." "0: Positive channel is in Discrete Mode and special..,1: Positive channel is in Continuous Mode and no.." bitfld.long 0xC 24. "NCHCTEN,Negative Channel Continuous Mode Enable." "0: Negative channel is in Discrete Mode and special..,1: Negative channel is in Continuous Mode and no.." newline bitfld.long 0xC 20. "RDIVE,Resistor Divider Enable" "0: The resistor is not enabled even when either..,1: The resistor is enabled because the inputs are.." bitfld.long 0xC 16. "DMCS,Discrete Mode Clock Selection" "0: Slow clock is selected for the timing generation.,1: Fast clock is selected for the timing generation." newline bitfld.long 0xC 12.--14. "ACSAT,Analog Comparator Sampling Time control." "0: The sampling time equals to T,1: The sampling time equasl to 2*T,2: The sampling time equasl to 4*T,3: The sampling time equasl to 8*T,4: The sampling time equasl to 16*T,5: The sampling time equasl to 32*T,6: The sampling time equasl to 64*T,7: The sampling time equasl to 256*T" bitfld.long 0xC 8.--10. "ACPH1TC,Analog Comparator Phase1 Timing Control." "0: Phase1 active time in one sampling period equals..,1: Phase1 active time in one sampling period equals..,2: Phase1 active time in one sampling period equals..,3: Phase1 active time in one sampling period equals..,4: Phase1 active time in one sampling period equals..,5: Phase1 active time in one sampling period equals..,6: Phase1 active time in one sampling period equals..,7: Phase1 active time in one sampling period equals.." newline bitfld.long 0xC 4.--6. "ACPH2TC,Analog Comparator Phase2 Timing Control." "0: Phase2 active time in one sampling period equals..,1: Phase2 active time in one sampling period equals..,2: Phase2 active time in one sampling period equals..,3: Phase2 active time in one sampling period equals..,4: Phase2 active time in one sampling period equals..,5: Phase2 active time in one sampling period equals..,6: Phase2 active time in one sampling period equals..,7: Phase2 active time in one sampling period equals.." tree.end tree "CMP3" base ad:0x401AC000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number. This read only field returns the major version number for the module specification." hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number. This read only field returns the minor version number for the module specification." newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number. This read only filed returns the feature set number." line.long 0x4 "PARAM,Parameter Register" hexmask.long 0x4 0.--31. 1. "PARAM,Parameter Registers. This read only filed returns the feature parameters implemented along with the Version ID register." group.long 0x8++0xF line.long 0x0 "C0,CMP Control Register 0" bitfld.long 0x0 31. "LINKEN,CMP to DAC link enable." "0: CMP to DAC link is disabled,1: CMP to DAC link is enabled." bitfld.long 0x0 30. "DMAEN,DMA Enable" "0: DMA is disabled.,1: DMA is enabled." newline bitfld.long 0x0 28. "IER,Comparator Interrupt Enable Rising" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 27. "IEF,Comparator Interrupt Enable Falling" "0: Interrupt is disabled.,1: Interrupt is enabled." newline eventfld.long 0x0 26. "CFR,Analog Comparator Flag Rising" "0: A rising edge has not been detected on COUT.,1: A rising edge on COUT has occurred." eventfld.long 0x0 25. "CFF,Analog Comparator Flag Falling" "0: A falling edge has not been detected on COUT.,1: A falling edge on COUT has occurred." newline rbitfld.long 0x0 24. "COUT,Analog Comparator Output" "0,1" hexmask.long.byte 0x0 16.--23. 1. "FPR,Filter Sample Period" newline bitfld.long 0x0 15. "SE,Sample Enable" "0: Sampling mode is not selected.,1: Sampling mode is selected." bitfld.long 0x0 14. "WE,Windowing Enable" "0: Windowing mode is not selected.,1: Windowing mode is selected." newline bitfld.long 0x0 12. "PMODE,Power Mode Select" "0: Low Speed (LS) comparison mode is selected.,1: High Speed (HS) comparison mode is selected." bitfld.long 0x0 11. "INVT,Comparator invert" "0: Does not invert the comparator output.,1: Inverts the comparator output." newline bitfld.long 0x0 10. "COS,Comparator Output Select" "0: Set CMPO to equal COUT (filtered comparator..,1: Set CMPO to equal COUTA (unfiltered comparator.." bitfld.long 0x0 9. "OPE,Comparator Output Pin Enable" "0: When OPE is 0 the comparator output (after..,1: When OPE is 1 and if the software has configured.." newline bitfld.long 0x0 8. "EN,Comparator Module Enable" "0: Analog Comparator is disabled.,1: Analog Comparator is enabled." bitfld.long 0x0 4.--6. "FILTER_CNT,Filter Sample Count" "0: Filter is disabled. If SE = 1 then COUT is a..,1: 1 consecutive sample must agree (comparator..,2: 2 consecutive samples must agree.,3: 3 consecutive samples must agree.,4: 4 consecutive samples must agree.,5: 5 consecutive samples must agree.,6: 6 consecutive samples must agree.,7: 7 consecutive samples must agree." newline bitfld.long 0x0 0.--1. "HYSTCTR,Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level" "0: The hard block output has level 0 hysteresis..,1: The hard block output has level 1 hysteresis..,2: The hard block output has level 2 hysteresis..,3: The hard block output has level 3 hysteresis.." line.long 0x4 "C1,CMP Control Register 1" bitfld.long 0x4 28.--30. "PSEL,Plus Input MUX Control" "0: Internal Positive Input 0 for Plus Channel --..,1: External Input 1 for Plus Channel -- Reference..,2: External Input 2 for Plus Channel -- Reference..,3: External Input 3 for Plus Channel -- Reference..,4: External Input 4 for Plus Channel -- Reference..,5: External Input 5 for Plus Channel -- Reference..,6: External Input 6 for Plus Channel -- Reference..,7: Internal 8b DAC output" bitfld.long 0x4 24.--26. "MSEL,Minus Input MUX Control" "0: Internal Negative Input 0 for Minus Channel --..,1: External Input 1 for Minus Channel -- Reference..,2: External Input 2 for Minus Channel -- Reference..,3: External Input 3 for Minus Channel -- Reference..,4: External Input 4 for Minus Channel -- Reference..,5: External Input 5 for Minus Channel -- Reference..,6: External Input 6 for Minus Channel -- Reference..,7: Internal 8b DAC output" newline bitfld.long 0x4 21. "CHN5,Channel 5 input enable" "0,1" bitfld.long 0x4 20. "CHN4,Channel 4 input enable" "0,1" newline bitfld.long 0x4 19. "CHN3,Channel 3 input enable" "0,1" bitfld.long 0x4 18. "CHN2,Channel 2 input enable" "0,1" newline bitfld.long 0x4 17. "CHN1,Channel 1 input enable" "0,1" bitfld.long 0x4 16. "CHN0,Channel 0 input enable" "0,1" newline bitfld.long 0x4 10. "DACEN,DAC Enable" "0: DAC is disabled.,1: DAC is enabled." bitfld.long 0x4 9. "VRSEL,Supply Voltage Reference Source Select" "0: Vin1 is selected as resistor ladder network..,1: Vin2 is selected as resistor ladder network.." newline bitfld.long 0x4 8. "DMODE,DAC Mode Selection" "0: DAC is selected to work in low speed and low..,1: DAC is selected to work in high speed high power.." hexmask.long.byte 0x4 0.--7. 1. "VOSEL,DAC Output Voltage Select" line.long 0x8 "C2,CMP Control Register 2" bitfld.long 0x8 30. "RRIE,Round-Robin interrupt enable" "0: The round-robin interrupt is disabled.,1: The round-robin interrupt is enabled when a.." bitfld.long 0x8 29. "FXMP,Fixed MUX Port" "0: The Plus port is fixed. Only the inputs to the..,1: The Minus port is fixed. Only the inputs to the.." newline bitfld.long 0x8 25.--27. "FXMXCH,Fixed channel selection" "0: External Reference Input 0 is selected as the..,1: External Reference Input 1 is selected as the..,2: External Reference Input 2 is selected as the..,3: External Reference Input 3 is selected as the..,4: External Reference Input 4 is selected as the..,5: External Reference Input 5 is selected as the..,?,7: The 8bit DAC is selected as the fixed reference.." eventfld.long 0x8 21. "CH5F,CH5F" "0,1" newline eventfld.long 0x8 20. "CH4F,CH4F" "0,1" eventfld.long 0x8 19. "CH3F,CH3F" "0,1" newline eventfld.long 0x8 18. "CH2F,CH2F" "0,1" eventfld.long 0x8 17. "CH1F,CH1F" "0,1" newline eventfld.long 0x8 16. "CH0F,CH0F" "0,1" bitfld.long 0x8 14.--15. "NSAM,Number of sample clocks" "0: The comparison result is sampled as soon as the..,1: The sampling takes place 1 round-robin clock..,2: The sampling takes place 2 round-robin clock..,3: The sampling takes place 3 round-robin clock.." newline hexmask.long.byte 0x8 8.--13. 1. "INITMOD,Comparator and DAC initialization delay modulus." hexmask.long.byte 0x8 0.--5. 1. "ACOn,ACOn" line.long 0xC "C3,CMP Control Register 3" bitfld.long 0xC 28. "PCHCTEN,Positive Channel Continuous Mode Enable." "0: Positive channel is in Discrete Mode and special..,1: Positive channel is in Continuous Mode and no.." bitfld.long 0xC 24. "NCHCTEN,Negative Channel Continuous Mode Enable." "0: Negative channel is in Discrete Mode and special..,1: Negative channel is in Continuous Mode and no.." newline bitfld.long 0xC 20. "RDIVE,Resistor Divider Enable" "0: The resistor is not enabled even when either..,1: The resistor is enabled because the inputs are.." bitfld.long 0xC 16. "DMCS,Discrete Mode Clock Selection" "0: Slow clock is selected for the timing generation.,1: Fast clock is selected for the timing generation." newline bitfld.long 0xC 12.--14. "ACSAT,Analog Comparator Sampling Time control." "0: The sampling time equals to T,1: The sampling time equasl to 2*T,2: The sampling time equasl to 4*T,3: The sampling time equasl to 8*T,4: The sampling time equasl to 16*T,5: The sampling time equasl to 32*T,6: The sampling time equasl to 64*T,7: The sampling time equasl to 256*T" bitfld.long 0xC 8.--10. "ACPH1TC,Analog Comparator Phase1 Timing Control." "0: Phase1 active time in one sampling period equals..,1: Phase1 active time in one sampling period equals..,2: Phase1 active time in one sampling period equals..,3: Phase1 active time in one sampling period equals..,4: Phase1 active time in one sampling period equals..,5: Phase1 active time in one sampling period equals..,6: Phase1 active time in one sampling period equals..,7: Phase1 active time in one sampling period equals.." newline bitfld.long 0xC 4.--6. "ACPH2TC,Analog Comparator Phase2 Timing Control." "0: Phase2 active time in one sampling period equals..,1: Phase2 active time in one sampling period equals..,2: Phase2 active time in one sampling period equals..,3: Phase2 active time in one sampling period equals..,4: Phase2 active time in one sampling period equals..,5: Phase2 active time in one sampling period equals..,6: Phase2 active time in one sampling period equals..,7: Phase2 active time in one sampling period equals.." tree.end tree "CMP4" base ad:0x401B0000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number. This read only field returns the major version number for the module specification." hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number. This read only field returns the minor version number for the module specification." newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number. This read only filed returns the feature set number." line.long 0x4 "PARAM,Parameter Register" hexmask.long 0x4 0.--31. 1. "PARAM,Parameter Registers. This read only filed returns the feature parameters implemented along with the Version ID register." group.long 0x8++0xF line.long 0x0 "C0,CMP Control Register 0" bitfld.long 0x0 31. "LINKEN,CMP to DAC link enable." "0: CMP to DAC link is disabled,1: CMP to DAC link is enabled." bitfld.long 0x0 30. "DMAEN,DMA Enable" "0: DMA is disabled.,1: DMA is enabled." newline bitfld.long 0x0 28. "IER,Comparator Interrupt Enable Rising" "0: Interrupt is disabled.,1: Interrupt is enabled." bitfld.long 0x0 27. "IEF,Comparator Interrupt Enable Falling" "0: Interrupt is disabled.,1: Interrupt is enabled." newline eventfld.long 0x0 26. "CFR,Analog Comparator Flag Rising" "0: A rising edge has not been detected on COUT.,1: A rising edge on COUT has occurred." eventfld.long 0x0 25. "CFF,Analog Comparator Flag Falling" "0: A falling edge has not been detected on COUT.,1: A falling edge on COUT has occurred." newline rbitfld.long 0x0 24. "COUT,Analog Comparator Output" "0,1" hexmask.long.byte 0x0 16.--23. 1. "FPR,Filter Sample Period" newline bitfld.long 0x0 15. "SE,Sample Enable" "0: Sampling mode is not selected.,1: Sampling mode is selected." bitfld.long 0x0 14. "WE,Windowing Enable" "0: Windowing mode is not selected.,1: Windowing mode is selected." newline bitfld.long 0x0 12. "PMODE,Power Mode Select" "0: Low Speed (LS) comparison mode is selected.,1: High Speed (HS) comparison mode is selected." bitfld.long 0x0 11. "INVT,Comparator invert" "0: Does not invert the comparator output.,1: Inverts the comparator output." newline bitfld.long 0x0 10. "COS,Comparator Output Select" "0: Set CMPO to equal COUT (filtered comparator..,1: Set CMPO to equal COUTA (unfiltered comparator.." bitfld.long 0x0 9. "OPE,Comparator Output Pin Enable" "0: When OPE is 0 the comparator output (after..,1: When OPE is 1 and if the software has configured.." newline bitfld.long 0x0 8. "EN,Comparator Module Enable" "0: Analog Comparator is disabled.,1: Analog Comparator is enabled." bitfld.long 0x0 4.--6. "FILTER_CNT,Filter Sample Count" "0: Filter is disabled. If SE = 1 then COUT is a..,1: 1 consecutive sample must agree (comparator..,2: 2 consecutive samples must agree.,3: 3 consecutive samples must agree.,4: 4 consecutive samples must agree.,5: 5 consecutive samples must agree.,6: 6 consecutive samples must agree.,7: 7 consecutive samples must agree." newline bitfld.long 0x0 0.--1. "HYSTCTR,Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level" "0: The hard block output has level 0 hysteresis..,1: The hard block output has level 1 hysteresis..,2: The hard block output has level 2 hysteresis..,3: The hard block output has level 3 hysteresis.." line.long 0x4 "C1,CMP Control Register 1" bitfld.long 0x4 28.--30. "PSEL,Plus Input MUX Control" "0: Internal Positive Input 0 for Plus Channel --..,1: External Input 1 for Plus Channel -- Reference..,2: External Input 2 for Plus Channel -- Reference..,3: External Input 3 for Plus Channel -- Reference..,4: External Input 4 for Plus Channel -- Reference..,5: External Input 5 for Plus Channel -- Reference..,6: External Input 6 for Plus Channel -- Reference..,7: Internal 8b DAC output" bitfld.long 0x4 24.--26. "MSEL,Minus Input MUX Control" "0: Internal Negative Input 0 for Minus Channel --..,1: External Input 1 for Minus Channel -- Reference..,2: External Input 2 for Minus Channel -- Reference..,3: External Input 3 for Minus Channel -- Reference..,4: External Input 4 for Minus Channel -- Reference..,5: External Input 5 for Minus Channel -- Reference..,6: External Input 6 for Minus Channel -- Reference..,7: Internal 8b DAC output" newline bitfld.long 0x4 21. "CHN5,Channel 5 input enable" "0,1" bitfld.long 0x4 20. "CHN4,Channel 4 input enable" "0,1" newline bitfld.long 0x4 19. "CHN3,Channel 3 input enable" "0,1" bitfld.long 0x4 18. "CHN2,Channel 2 input enable" "0,1" newline bitfld.long 0x4 17. "CHN1,Channel 1 input enable" "0,1" bitfld.long 0x4 16. "CHN0,Channel 0 input enable" "0,1" newline bitfld.long 0x4 10. "DACEN,DAC Enable" "0: DAC is disabled.,1: DAC is enabled." bitfld.long 0x4 9. "VRSEL,Supply Voltage Reference Source Select" "0: Vin1 is selected as resistor ladder network..,1: Vin2 is selected as resistor ladder network.." newline bitfld.long 0x4 8. "DMODE,DAC Mode Selection" "0: DAC is selected to work in low speed and low..,1: DAC is selected to work in high speed high power.." hexmask.long.byte 0x4 0.--7. 1. "VOSEL,DAC Output Voltage Select" line.long 0x8 "C2,CMP Control Register 2" bitfld.long 0x8 30. "RRIE,Round-Robin interrupt enable" "0: The round-robin interrupt is disabled.,1: The round-robin interrupt is enabled when a.." bitfld.long 0x8 29. "FXMP,Fixed MUX Port" "0: The Plus port is fixed. Only the inputs to the..,1: The Minus port is fixed. Only the inputs to the.." newline bitfld.long 0x8 25.--27. "FXMXCH,Fixed channel selection" "0: External Reference Input 0 is selected as the..,1: External Reference Input 1 is selected as the..,2: External Reference Input 2 is selected as the..,3: External Reference Input 3 is selected as the..,4: External Reference Input 4 is selected as the..,5: External Reference Input 5 is selected as the..,?,7: The 8bit DAC is selected as the fixed reference.." eventfld.long 0x8 21. "CH5F,CH5F" "0,1" newline eventfld.long 0x8 20. "CH4F,CH4F" "0,1" eventfld.long 0x8 19. "CH3F,CH3F" "0,1" newline eventfld.long 0x8 18. "CH2F,CH2F" "0,1" eventfld.long 0x8 17. "CH1F,CH1F" "0,1" newline eventfld.long 0x8 16. "CH0F,CH0F" "0,1" bitfld.long 0x8 14.--15. "NSAM,Number of sample clocks" "0: The comparison result is sampled as soon as the..,1: The sampling takes place 1 round-robin clock..,2: The sampling takes place 2 round-robin clock..,3: The sampling takes place 3 round-robin clock.." newline hexmask.long.byte 0x8 8.--13. 1. "INITMOD,Comparator and DAC initialization delay modulus." hexmask.long.byte 0x8 0.--5. 1. "ACOn,ACOn" line.long 0xC "C3,CMP Control Register 3" bitfld.long 0xC 28. "PCHCTEN,Positive Channel Continuous Mode Enable." "0: Positive channel is in Discrete Mode and special..,1: Positive channel is in Continuous Mode and no.." bitfld.long 0xC 24. "NCHCTEN,Negative Channel Continuous Mode Enable." "0: Negative channel is in Discrete Mode and special..,1: Negative channel is in Continuous Mode and no.." newline bitfld.long 0xC 20. "RDIVE,Resistor Divider Enable" "0: The resistor is not enabled even when either..,1: The resistor is enabled because the inputs are.." bitfld.long 0xC 16. "DMCS,Discrete Mode Clock Selection" "0: Slow clock is selected for the timing generation.,1: Fast clock is selected for the timing generation." newline bitfld.long 0xC 12.--14. "ACSAT,Analog Comparator Sampling Time control." "0: The sampling time equals to T,1: The sampling time equasl to 2*T,2: The sampling time equasl to 4*T,3: The sampling time equasl to 8*T,4: The sampling time equasl to 16*T,5: The sampling time equasl to 32*T,6: The sampling time equasl to 64*T,7: The sampling time equasl to 256*T" bitfld.long 0xC 8.--10. "ACPH1TC,Analog Comparator Phase1 Timing Control." "0: Phase1 active time in one sampling period equals..,1: Phase1 active time in one sampling period equals..,2: Phase1 active time in one sampling period equals..,3: Phase1 active time in one sampling period equals..,4: Phase1 active time in one sampling period equals..,5: Phase1 active time in one sampling period equals..,6: Phase1 active time in one sampling period equals..,7: Phase1 active time in one sampling period equals.." newline bitfld.long 0xC 4.--6. "ACPH2TC,Analog Comparator Phase2 Timing Control." "0: Phase2 active time in one sampling period equals..,1: Phase2 active time in one sampling period equals..,2: Phase2 active time in one sampling period equals..,3: Phase2 active time in one sampling period equals..,4: Phase2 active time in one sampling period equals..,5: Phase2 active time in one sampling period equals..,6: Phase2 active time in one sampling period equals..,7: Phase2 active time in one sampling period equals.." tree.end tree.end sif (cpuis("IMXRT1166-CM4")||cpuis("IMXRT1166-CM7")) tree "CSI" base ad:0x40800000 group.long 0x0++0xB line.long 0x0 "CR1,CSI Control Register 1" bitfld.long 0x0 31. "SWAP16_EN,SWAP 16-Bit Enable" "0: Disable swapping,1: Enable swapping" newline bitfld.long 0x0 30. "EXT_VSYNC,External VSYNC Enable" "0: Internal VSYNC mode,1: External VSYNC mode" newline bitfld.long 0x0 29. "EOF_INT_EN,End-of-Frame Interrupt Enable. This bit enables and disables the EOF interrupt." "0: EOF interrupt is disabled.,1: EOF interrupt is generated when RX count value.." newline bitfld.long 0x0 27. "VIDEO_MODE,Video mode select. This bit controls the video mode in BT.656 mode and TV decoder input." "0: Progressive mode is selected,1: Interlace mode is selected" newline bitfld.long 0x0 26. "COF_INT_EN,Change Of Image Field (COF) Interrupt Enable" "0: COF interrupt is disabled,1: COF interrupt is enabled" newline bitfld.long 0x0 25. "SF_OR_INTEN,STAT FIFO Overrun Interrupt Enable. This bit enables the STATFIFO overrun interrupt." "0: STATFIFO overrun interrupt is disabled,1: STATFIFO overrun interrupt is enabled" newline bitfld.long 0x0 24. "RF_OR_INTEN,RxFIFO Overrun Interrupt Enable. This bit enables the RX FIFO overrun interrupt." "0: RxFIFO overrun interrupt is disabled,1: RxFIFO overrun interrupt is enabled" newline bitfld.long 0x0 22. "SFF_DMA_DONE_INTEN,STATFIFO DMA Transfer Done Interrupt Enable" "0: STATFIFO DMA Transfer Done interrupt disable,1: STATFIFO DMA Transfer Done interrupt enable" newline bitfld.long 0x0 21. "STATFF_INTEN,STATFIFO Full Interrupt Enable. This bit enables the STAT FIFO interrupt." "0: STATFIFO full interrupt disable,1: STATFIFO full interrupt enable" newline bitfld.long 0x0 20. "FB2_DMA_DONE_INTEN,Frame Buffer2 DMA Transfer Done Interrupt Enable" "0: Frame Buffer2 DMA Transfer Done interrupt disable,1: Frame Buffer2 DMA Transfer Done interrupt enable" newline bitfld.long 0x0 19. "FB1_DMA_DONE_INTEN,Frame Buffer1 DMA Transfer Done Interrupt Enable" "0: Frame Buffer1 DMA Transfer Done interrupt disable,1: Frame Buffer1 DMA Transfer Done interrupt enable" newline bitfld.long 0x0 18. "RXFF_INTEN,RxFIFO Full Interrupt Enable. This bit enables the RxFIFO full interrupt." "0: RxFIFO full interrupt disable,1: RxFIFO full interrupt enable" newline bitfld.long 0x0 17. "SOF_POL,SOF Interrupt Polarity. This bit controls the condition that generates an SOF interrupt." "0: SOF interrupt is generated on SOF falling edge,1: SOF interrupt is generated on SOF rising edge" newline bitfld.long 0x0 16. "SOF_INTEN,Start Of Frame (SOF) Interrupt Enable. This bit enables the SOF interrupt." "0: SOF interrupt disable,1: SOF interrupt enable" newline bitfld.long 0x0 12. "HISTOGRAM_CALC_DONE_IE,Histogram Interrupt Enable" "0: Histogram done interrupt disable,1: Histogram done interrupt enable" newline bitfld.long 0x0 11. "HSYNC_POL,HSYNC Polarity Select" "0: HSYNC is active low,1: HSYNC is active high" newline bitfld.long 0x0 10. "CCIR_EN,BT.656 Interface Enable. This bit selects the type of interface used." "0: Traditional interface is selected.,1: BT.656 interface is selected." newline bitfld.long 0x0 8. "FCC,FIFO Clear Control" "0: Asynchronous FIFO clear is selected.,1: Synchronous FIFO clear is selected." newline bitfld.long 0x0 7. "PACK_DIR,Data Packing Direction" "0: Pack from LSB first. For image data 0x11 0x22..,1: Pack from MSB first. For image data 0x11 0x22.." newline bitfld.long 0x0 6. "CLR_STATFIFO,Asynchronous STATFIFO Clear" "0,1" newline bitfld.long 0x0 5. "CLR_RXFIFO,Asynchronous RXFIFO Clear" "0,1" newline bitfld.long 0x0 4. "GCLK_MODE,Gated Clock Mode Enable" "0: Non-gated clock mode. All incoming pixel clocks..,1: Gated clock mode. Pixel clock signal is valid.." newline bitfld.long 0x0 3. "INV_DATA,Invert Data Input. This bit enables or disables internal inverters on the data lines." "0: CSI_D[7:0] data lines are directly applied to..,1: CSI_D[7:0] data lines are inverted before.." newline bitfld.long 0x0 2. "INV_PCLK,Invert Pixel Clock Input" "0: CSI_PIXCLK is directly applied to internal..,1: CSI_PIXCLK is inverted before applied to.." newline bitfld.long 0x0 1. "REDGE,Valid Pixel Clock Edge Select" "0: Pixel data is latched at the falling edge of..,1: Pixel data is latched at the rising edge of.." newline bitfld.long 0x0 0. "PIXEL_BIT,Pixel Bit" "0: 8-bit data for each pixel,1: 10-bit data for each pixel" line.long 0x4 "CR2,CSI Control Register 2" bitfld.long 0x4 30.--31. "DMA_BURST_TYPE_RFF,Burst Type of DMA Transfer from RxFIFO. Selects the burst type of DMA transfer from RxFIFO." "0: INCR8,1: INCR4,2: INCR8,3: INCR16" newline bitfld.long 0x4 28.--29. "DMA_BURST_TYPE_SFF,Burst Type of DMA Transfer from STATFIFO. Selects the burst type of DMA transfer from STATFIFO." "0: INCR8,1: INCR4,2: INCR8,3: INCR16" newline bitfld.long 0x4 26. "DRM,Double Resolution Mode. Controls size of statistics grid." "0: Stats grid of 8 x 6,1: Stats grid of 8 x 12" newline bitfld.long 0x4 24.--25. "AFS,Auto Focus Spread. Selects which green pixels are used for auto-focus." "0: Abs Diff on every four green pixels,1: Abs Diff on every third green pixels,2: Abs Diff on every four green pixels,3: Abs Diff on every four green pixels" newline bitfld.long 0x4 23. "SCE,Skip Count Enable" "0: Skip count disable,1: Skip count enable" newline bitfld.long 0x4 19.--20. "BTS,Bayer Tile Start. Controls the Bayer pattern starting point." "0: GR,1: RG,2: BG,3: GB" newline bitfld.long 0x4 16.--18. "LVRM,Live View Resolution Mode. Selects the grid size used for live view resolution." "0: 512 x 384,1: 448 x 336,2: 384 x 288,3: 384 x 256,4: 320 x 240,5: 288 x 216,6: 400 x 300,?" newline hexmask.long.byte 0x4 8.--15. 1. "VSC,Vertical Skip Count. Contains the number of rows to skip. SCE must be 1 otherwise VSC is ignored." newline hexmask.long.byte 0x4 0.--7. 1. "HSC,Horizontal Skip Count" line.long 0x8 "CR3,CSI Control Register 3" hexmask.long.word 0x8 16.--31. 1. "FRMCNT,Frame Counter" newline bitfld.long 0x8 15. "FRMCNT_RST,Frame Count Reset. Resets the Frame Counter. (Cleared automatically after reset is done)" "0: Do not reset,1: Reset frame counter immediately" newline bitfld.long 0x8 14. "DMA_REFLASH_RFF,Reflash DMA Controller for RxFIFO" "0: No reflashing,1: Reflash the embedded DMA controller" newline bitfld.long 0x8 13. "DMA_REFLASH_SFF,Reflash DMA Controller for STATFIFO" "0: No reflashing,1: Reflash the embedded DMA controller" newline bitfld.long 0x8 12. "DMA_REQ_EN_RFF,DMA Request Enable for RxFIFO" "0: Disable the dma request,1: Enable the dma request" newline bitfld.long 0x8 11. "DMA_REQ_EN_SFF,DMA Request Enable for STATFIFO" "0: Disable the dma request,1: Enable the dma request" newline bitfld.long 0x8 8.--10. "STATFF_LEVEL,STATFIFO Full Level" "0: 4 Double words,1: 8 Double words,2: 12 Double words,3: 16 Double words,4: 24 Double words,5: 32 Double words,6: 48 Double words,7: 64 Double words" newline bitfld.long 0x8 7. "HRESP_ERR_EN,Hresponse Error Enable. This bit enables the hresponse (AHB protocol standard) error interrupt." "0: Disable hresponse error interrupt,1: Enable hresponse error interrupt" newline bitfld.long 0x8 4.--6. "RxFF_LEVEL,RxFIFO Full Level" "0: 4 Double words,1: 8 Double words,2: 16 Double words,3: 24 Double words,4: 32 Double words,5: 48 Double words,6: 64 Double words,7: 96 Double words" newline bitfld.long 0x8 3. "SENSOR_16BITS,16-bit Sensor Mode" "0: Only one 8-bit sensor is connected.,1: One 16-bit sensor is connected." newline bitfld.long 0x8 2. "ZERO_PACK_EN,Dummy Zero Packing Enable" "0: Zero packing disabled,1: Zero packing enabled" newline bitfld.long 0x8 1. "ECC_INT_EN,Error Detection Interrupt Enable" "0: No interrupt is generated when error is..,1: Interrupt is generated when error is detected." newline bitfld.long 0x8 0. "ECC_AUTO_EN,Automatic Error Correction Enable" "0: Auto Error correction is disabled.,1: Auto Error correction is enabled." rgroup.long 0xC++0x7 line.long 0x0 "STATFIFO,CSI Statistic FIFO Register" hexmask.long 0x0 0.--31. 1. "STAT,Static data from sensor" line.long 0x4 "RFIFO,CSI RX FIFO Register" hexmask.long 0x4 0.--31. 1. "IMAGE,Received image data" group.long 0x14++0x7 line.long 0x0 "RXCNT,CSI RX Count Register" hexmask.long.tbyte 0x0 0.--21. 1. "RXCNT,RxFIFO Count" line.long 0x4 "SR,CSI Status Register" bitfld.long 0x4 28. "BASEADDR_CHHANGE_ERROR,When using base address switching enable this bit will be 1 when switching occur before DMA complete" "0,1" newline bitfld.long 0x4 27. "DMA_FIELD0_DONE,When DMA field 0 is complete this bit will be set to 1(clear by writing 1)." "0,1" newline bitfld.long 0x4 26. "DMA_FIELD1_DONE,When DMA field 1 is complete this bit will be set to 1(clear by writing 1)." "0,1" newline bitfld.long 0x4 25. "SF_OR_INT,STATFIFO Overrun Interrupt Status" "0: STATFIFO has not overflowed.,1: STATFIFO has overflowed." newline bitfld.long 0x4 24. "RF_OR_INT,RxFIFO Overrun Interrupt Status" "0: RXFIFO has not overflowed.,1: RXFIFO has overflowed." newline bitfld.long 0x4 22. "DMA_TSF_DONE_SFF,DMA Transfer Done from StatFIFO" "0: DMA transfer is not completed.,1: DMA transfer is completed." newline bitfld.long 0x4 21. "STATFF_INT,STATFIFO Full Interrupt Status" "0: STATFIFO is not full.,1: STATFIFO is full." newline bitfld.long 0x4 20. "DMA_TSF_DONE_FB2,DMA Transfer Done in Frame Buffer2" "0: DMA transfer is not completed.,1: DMA transfer is completed." newline bitfld.long 0x4 19. "DMA_TSF_DONE_FB1,DMA Transfer Done in Frame Buffer1" "0: DMA transfer is not completed.,1: DMA transfer is completed." newline bitfld.long 0x4 18. "RxFF_INT,RXFIFO Full Interrupt Status" "0: RxFIFO is not full.,1: RxFIFO is full." newline bitfld.long 0x4 17. "EOF_INT,End of Frame (EOF) Interrupt Status. Indicates when EOF is detected. (Cleared by writing 1)" "0: EOF is not detected.,1: EOF is detected." newline bitfld.long 0x4 16. "SOF_INT,Start of Frame Interrupt Status. Indicates when SOF is detected. (Cleared by writing 1)" "0: SOF is not detected.,1: SOF is detected." newline bitfld.long 0x4 15. "F2_INT,BT" "0: Field 2 of video is not detected,1: Field 2 of video is about to start" newline bitfld.long 0x4 14. "F1_INT,BT" "0: Field 1 of video is not detected.,1: Field 1 of video is about to start." newline bitfld.long 0x4 13. "COF_INT,Change Of Field Interrupt Status" "0: Video field has no change.,1: Change of video field is detected." newline bitfld.long 0x4 7. "HRESP_ERR_INT,Hresponse Error Interrupt Status" "0: No hresponse error.,1: Hresponse error is detected." newline bitfld.long 0x4 2. "HISTOGRAM_CALC_DONE_INT,no description available" "0: Histogram calculation is not finished,1: Histogram calculation is done and driver can.." newline bitfld.long 0x4 1. "ECC_INT,BT" "0: No error detected,1: Error is detected in BT.656 coding" newline bitfld.long 0x4 0. "DRDY,RXFIFO Data Ready" "0: No data (word) is ready,1: At least 1 datum (word) is ready in RXFIFO." group.long 0x20++0x17 line.long 0x0 "DMASA_STATFIFO,CSI DMA Start Address Register - for STATFIFO" hexmask.long 0x0 2.--31. 1. "DMA_START_ADDR_SFF,DMA Start Address for STATFIFO" line.long 0x4 "DMATS_STATFIFO,CSI DMA Transfer Size Register - for STATFIFO" hexmask.long 0x4 0.--31. 1. "DMA_TSF_SIZE_SFF,DMA Transfer Size for STATFIFO" line.long 0x8 "DMASA_FB1,CSI DMA Start Address Register - for Frame Buffer1" hexmask.long 0x8 2.--31. 1. "DMA_START_ADDR_FB1,DMA Start Address in Frame Buffer1" line.long 0xC "DMASA_FB2,CSI DMA Transfer Size Register - for Frame Buffer2" hexmask.long 0xC 2.--31. 1. "DMA_START_ADDR_FB2,DMA Start Address in Frame Buffer2" line.long 0x10 "FBUF_PARA,CSI Frame Buffer Parameter Register" hexmask.long.word 0x10 16.--31. 1. "DEINTERLACE_STRIDE,DEINTERLACE_STRIDE is only used in the deinterlace mode" newline hexmask.long.word 0x10 0.--15. 1. "FBUF_STRIDE,Frame Buffer Parameter" line.long 0x14 "IMAG_PARA,CSI Image Parameter Register" hexmask.long.word 0x14 16.--31. 1. "IMAGE_WIDTH,This field indicates the number of active pixel cycles per line" newline hexmask.long.word 0x14 0.--15. 1. "IMAGE_HEIGHT,Image Height. Indicates how many pixels in a column of the image from the sensor." group.long 0x48++0xB line.long 0x0 "CR18,CSI Control Register 18" bitfld.long 0x0 31. "CSI_ENABLE,CSI global enable signal" "0,1" newline hexmask.long.byte 0x0 25.--30. 1. "MIPI_DATA_FORMAT,Image Data Format" newline bitfld.long 0x0 24. "LINE_STRIDE_EN,When the line width are not the multiple of the burst length assert this bit." "0,1" newline bitfld.long 0x0 22. "DATA_FROM_MIPI,no description available" "0: Data from parallel sensor,1: Data from MIPI" newline bitfld.long 0x0 21. "MIPI_YU_SWAP,It only works in MIPI CSI YUV422 double component mode." "0,1" newline bitfld.long 0x0 20. "MIPI_DOUBLE_CMPNT,Double component per clock cycle in YUV422 formats." "0: Single component per clock cycle (half pixel per..,1: Double component per clock cycle (a pixel per.." newline bitfld.long 0x0 18.--19. "MASK_OPTION,These bits used to choose the method to mask the CSI input." "0: Writing to memory (OCRAM or external DDR) from..,1: Writing to memory when CSI_ENABLE is 1.,2: Writing to memory from second completely frame..,3: Writing to memory when data comes in not matter.." newline hexmask.long.byte 0x0 12.--15. 1. "AHB_HPROT,Hprot value in AHB bus protocol." newline bitfld.long 0x0 10. "RGB888A_FORMAT_SEL,Output is 32-bit format." "0: {8'h0 data[23:0]},1: {data[23:0] 8'h0}" newline bitfld.long 0x0 9. "BASEADDR_CHANGE_ERROR_IE,Base address change error interrupt enable signal." "0: Interrupt disabled,1: Interrupt enabled" newline bitfld.long 0x0 8. "LAST_DMA_REQ_SEL,Choosing the last DMA request condition" "0: fifo_full_level,1: hburst_length" newline bitfld.long 0x0 7. "DMA_FIELD1_DONE_IE,When in interlace mode field 1 done interrupt enable." "0: Interrupt disabled,1: Interrupt enabled" newline bitfld.long 0x0 6. "FIELD0_DONE_IE,In interlace mode field 0 means interrupt enabled." "0: Interrupt disabled,1: Interrupt enabled" newline bitfld.long 0x0 5. "BASEADDR_SWITCH_SEL,CSI 2 base addresses switching method. When using this bit BASEADDR_SWITCH_EN is 1." "0: Switching base address at the edge of the vsync,1: Switching base address at the edge of the first.." newline bitfld.long 0x0 4. "BASEADDR_SWITCH_EN,When this bit is enabled CSI DMA will switch the base address according to BASEADDR_SWITCH_SEL rather than automatically by DMA completed" "0,1" newline bitfld.long 0x0 3. "PARALLEL24_EN,Enable bit for Parallel RGB888/YUV444 24bit input" "0: Input is disabled,1: Input is enabled" newline bitfld.long 0x0 2. "DEINTERLACE_EN,This bit is used to select the output method When input is TVDECODER or standard BT.656 video." "0: Deinterlace disabled,1: Deinterlace enabled" newline bitfld.long 0x0 1. "TVDECODER_IN_EN,When input is from TV decoder this bit is enabled." "0,1" newline bitfld.long 0x0 0. "NTSC_EN,This bit is used to select NTSC/PAL mode When input is TVDECODER or standard BT.656 video." "0: PAL,1: NTSC" line.long 0x4 "CR19,CSI Control Register 19" hexmask.long.byte 0x4 0.--7. 1. "DMA_RFIFO_HIGHEST_FIFO_LEVEL,This byte stores the highest FIFO level achieved by CSI FIFO timely and will be clear by writing 8'ff to it" line.long 0x8 "CR20,CSI Control Register 20" bitfld.long 0x8 31. "QRCODE_EN,Gray scale mode enable" "0: Normal mode,1: Gray scale mode" newline bitfld.long 0x8 30. "HISTOGRAM_EN,Histogram enable" "0: Histogram disable,1: Histogram enable" newline bitfld.long 0x8 29. "_10BIT_NEW_EN,no description available" "0: When input 8bits data it will use the data[9:2],1: If input is 10bits data it will use the.." newline bitfld.long 0x8 12. "BIG_END,no description available" "0: The newest (most recent) data will be assigned..,1: The newest (most recent) data will be assigned.." newline bitfld.long 0x8 9.--11. "QR_DATA_FORMAT,no description available" "0: YU YV one cycle per 1 pixel input,1: UY VY one cycle per1 pixel input,2: Y U Y V two cycles per 1 pixel input,3: U Y V Y two cycles per 1 pixel input,4: YUV one cycle per 1 pixel input,5: Y U V three cycles per 1 pixel input,?,?" newline bitfld.long 0x8 8. "BINARY_EN,no description available" "0: Output is Y8 format(8 bits each pixel),1: Output is Y1 format(1 bit each pixel)" newline hexmask.long.byte 0x8 0.--7. 1. "THRESHOLD,THRESHOLD used for binary function. When data value > THRESHOLD output will be 1 Else will be 0." repeat 256. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x54)++0x3 line.long 0x0 "CR$1,CSI Control Register" hexmask.long.tbyte 0x0 0.--23. 1. "PIXEL_COUNTERS,Number of pixels (Y component of the input pixel) equals: 0 (CSICR21) 1 (CSICR22)" repeat.end tree.end endif tree "DAC" base ad:0x40064000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version Identifier Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major version number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor version number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" bitfld.long 0x4 0.--2. "FIFOSZ,FIFO size" "0: FIFO depth is 2,1: FIFO depth is 4,2: FIFO depth is 8,3: FIFO depth is 16,4: FIFO depth is 32,5: FIFO depth is 64,6: FIFO depth is 128,7: FIFO depth is 256" wgroup.long 0x8++0x3 line.long 0x0 "DATA,DAC Data Register" hexmask.long.word 0x0 0.--11. 1. "DATA0,FIFO DATA0" group.long 0xC++0x3 line.long 0x0 "CR,DAC Status and Control Register" hexmask.long.byte 0x0 24.--31. 1. "WML,Watermark Level Select" bitfld.long 0x0 23. "DMAEN,DMA Enable Select" "0: DMA is disabled.,1: DMA is enabled. When DMA is enabled the DMA.." newline bitfld.long 0x0 22. "SWRST,Software reset" "0,1" bitfld.long 0x0 21. "FIFORST,FIFO Reset" "0: No effect,1: FIFO reset" newline bitfld.long 0x0 18. "UVIE,Underflow and overflow interrupt enable" "0: Underflow and overflow interrupt is disabled.,1: Underflow and overflow interrupt is enabled." bitfld.long 0x0 17. "SWMD,DAC FIFO Mode Select" "0: Normal mode,1: Swing back mode" newline bitfld.long 0x0 16. "FIFOEN,FIFO Enable" "0: FIFO is disabled and only one level buffer is..,1: FIFO is enabled. Data will first read from FIFO.." bitfld.long 0x0 15. "DACEN,DAC Enable" "0: The DAC system is disabled.,1: The DAC system is enabled." newline bitfld.long 0x0 14. "DACRFS,DAC Reference Select" "0: The DAC selects DACREF_1 as the reference voltage.,1: The DAC selects DACREF_2 as the reference voltage." bitfld.long 0x0 13. "TRGSEL,DAC Trigger Select" "0: The DAC hardware trigger is selected.,1: The DAC software trigger is selected." newline bitfld.long 0x0 12. "SWTRG,DAC Software Trigger" "0: The DAC soft trigger is not valid.,1: The DAC soft trigger is valid." bitfld.long 0x0 10. "WTMIE,Watermark Interrupt Enable" "0: Watermark interrupt is disabled.,1: Watermark interrupt is enabled." newline bitfld.long 0x0 9. "EMPTIE,Nearly Empty Interrupt Enable" "0: FIFO Nearly Empty interrupt is disabled.,1: FIFO Nearly Empty interrupt is enabled." bitfld.long 0x0 8. "FULLIE,Full Interrupt Enable" "0: FIFO Full interrupt is disabled.,1: FIFO Full interrupt is enabled." newline bitfld.long 0x0 4. "OVFF,Overflow Flag" "0: No overflow has occurred since the last time the..,1: At least one FIFO overflow has occurred since.." bitfld.long 0x0 3. "UDFF,Underflow Flag" "0: No underflow has occurred since the last time..,1: At least one trigger underflow has occurred.." newline bitfld.long 0x0 2. "WMF,FIFO Watermark Status Flag" "0: The DAC buffer read pointer has not reached the..,1: The DAC buffer read pointer has reached the.." bitfld.long 0x0 1. "NEMPTF,Nearly Empty Flag" "0: More than one data is available in the FIFO.,1: One data is available in the FIFO." newline bitfld.long 0x0 0. "FULLF,Full Flag" "0: FIFO is not full.,1: FIFO is full." rgroup.long 0x10++0x3 line.long 0x0 "PTR,DAC FIFO Pointer Register" hexmask.long.byte 0x0 16.--23. 1. "DACRFP,DACRFP" hexmask.long.byte 0x0 0.--7. 1. "DACWFP,DACWFP" group.long 0x14++0x3 line.long 0x0 "CR2,DAC Status and Control Register 2" bitfld.long 0x0 6. "IREF,Internal Current Reference Select" "0: Internal Current Reference not selected,1: Internal Current Reference selected" bitfld.long 0x0 5. "IREF1,Internal ZTC (Zero Temperature Coefficient) Current Reference Select" "0: Internal ZTC Current Reference not selected,1: Internal ZTC Current Reference selected" newline bitfld.long 0x0 4. "IREF2,Internal PTAT (Proportional To Absolute Temperature) Current Reference Select" "0: Internal PTAT Current Reference not selected,1: Internal PTAT Current Reference selected" bitfld.long 0x0 3. "BFHS,Buffer High Speed Select" "0: Buffer high speed not selected,1: Buffer high speed selected" newline bitfld.long 0x0 2. "BFMS,Buffer Middle Speed Select" "0: Buffer middle speed not selected,1: Buffer middle speed selected" bitfld.long 0x0 1. "OEN,Optional Enable" "0: Output buffer is not bypassed,1: Output buffer is bypassed" newline bitfld.long 0x0 0. "BFEN,Buffer Enable" "0: Opamp is not used as buffer,1: Opamp is used as buffer" tree.end tree "DCDC" base ad:0x40CA8000 group.long 0x0++0x6F line.long 0x0 "CTRL0,DCDC Control Register 0" bitfld.long 0x0 31. "CONTROL_MODE,Control mode" "0: Software control mode,1: Hardware control mode (controlled by GPC.." newline hexmask.long.word 0x0 19.--30. 1. "DEBUG_BITS,DEBUG_BITS[11:0]" newline bitfld.long 0x0 6. "TRIM_HOLD,Hold trim input" "0: Sample trim input,1: Hold trim input" newline bitfld.long 0x0 5. "ENABLE_DCDC_CNT,Enable internal count for DCDC_OK timeout" "0: Wait DCDC_OK for ACK,1: Enable internal count for DCDC_OK timeout" newline bitfld.long 0x0 4. "STBY_LP_MODE_EN,DCDC low-power mode enable by GPC standby request" "0: Disable DCDC entry into low-power mode from a..,1: Enable DCDC to enter into low-power mode from a.." newline bitfld.long 0x0 3. "LP_MODE_EN,DCDC low-power (LP) mode enable DCDC can't start up directly into LP mode" "?,1: Enter into low-power mode" newline bitfld.long 0x0 2. "STBY_EN,DCDC standby mode enable" "?,1: Enter into standby mode" newline bitfld.long 0x0 1. "DIG_EN,Enable the DCDC_DIG switching converter output" "?,1: Enable" newline bitfld.long 0x0 0. "ENABLE,DCDC Enable" "0: Disable (Bypass),1: Enable" line.long 0x4 "CTRL1,DCDC Control Register 1" hexmask.long.byte 0x4 24.--28. 1. "VDD1P0CTRL_STBY_TRG,Target value of VDD1P0 in standby mode 25mV each step from 0x00 to 0x1F:" newline hexmask.long.byte 0x4 16.--20. 1. "VDD1P8CTRL_STBY_TRG,Target value of VDD1P8 in standby mode 25mV each step from 0x00 to 0x1F:" newline hexmask.long.byte 0x4 8.--12. 1. "VDD1P0CTRL_TRG,Target value of VDD1P0 in buck mode 25mV each step from 0x00 to 0x1F:" newline hexmask.long.byte 0x4 0.--4. 1. "VDD1P8CTRL_TRG,Target value of VDD1P8 in buck mode 25mV each step from 0x00 to 0x1F:" line.long 0x8 "REG0,DCDC Register 0" rbitfld.long 0x8 31. "STS_DC_OK,DCDC Output OK" "0: DCDC is settling,1: DCDC already settled" newline bitfld.long 0x8 29. "XTAL_24M_OK,24M XTAL OK" "0: DCDC uses internal ring oscillator,1: DCDC uses xtal 24M" newline bitfld.long 0x8 27. "XTALOK_DISABLE,Disable xtalok detection circuit" "0: Enable xtalok detection circuit,1: Disable xtalok detection circuit and always.." newline bitfld.long 0x8 26. "PWD_CMP_OFFSET,power down the out-of-range detection comparator" "0: Out-of-range comparator powered up,1: Out-of-range comparator powered down" newline bitfld.long 0x8 21. "LP_HIGH_HYS,Low Power High Hysteric Value" "0: Adjust hysteretic value in low power to 12.5mV,1: Adjust hysteretic value in low power to 25mV" newline bitfld.long 0x8 17. "PWD_HIGH_VDD1P0_DET,Power Down High Voltage Detection for VDD1P0" "0: Overvoltage detection comparator for the VDD1P0..,1: Overvoltage detection comparator for the VDD1P0.." newline bitfld.long 0x8 16. "PWD_HIGH_VDD1P8_DET,Power Down High Voltage Detection for VDD1P8" "0: Overvoltage detection comparator for the VDD1P8..,1: Overvoltage detection comparator for the VDD1P8.." newline bitfld.long 0x8 11. "PWD_CMP_DCDC_IN_DET,Set to '1' to power down the low voltage detection comparator" "0: Low voltage detection comparator is enabled,1: Low voltage detection comparator is disabled" newline bitfld.long 0x8 8. "PWD_OVERCUR_DET,Power down overcurrent detection comparator" "0: Overcurrent detection comparator is enabled,1: Overcurrent detection comparator is disabled" newline bitfld.long 0x8 5.--7. "CUR_SNS_THRSH,Current Sense (detector) Threshold" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 4. "PWD_CUR_SNS_CMP,Power down signal of the current detector" "0: Current Detector powered up,1: Current Detector powered down" newline bitfld.long 0x8 3. "PWD_OSC_INT,Power down internal ring oscillator" "0: Internal ring oscillator powered up,1: Internal ring oscillator powered down" newline bitfld.long 0x8 2. "SEL_CLK,Select Clock" "0: DCDC uses internal ring oscillator,1: DCDC uses 24M xtal" newline bitfld.long 0x8 1. "DISABLE_AUTO_CLK_SWITCH,Disable Auto Clock Switch" "0: If DISABLE_AUTO_CLK_SWITCH is set to 0 and 24M..,1: If DISABLE_AUTO_CLK_SWITCH is set to 1 SEL_CLK.." newline bitfld.long 0x8 0. "PWD_ZCD,Power Down Zero Cross Detection" "0: Zero cross detetion function powered up,1: Zero cross detetion function powered down" line.long 0xC "REG1,DCDC Register 1" bitfld.long 0xC 30. "LOOPCTRL_EN_DF_HYST,Enable hysteresis in switching converter differential mode analog comparators" "0: Disable hysteresis in switching converter..,1: Enable hysteresis in switching converter.." newline bitfld.long 0xC 29. "LOOPCTRL_EN_CM_HYST,Enable hysteresis in switching converter common mode analog comparators" "0: Disable hysteresis in switching converter common..,1: Enable hysteresis in switching converter common.." newline bitfld.long 0xC 28. "LOOPCTRL_DF_HST_THRESH,Increase Threshold Detection" "0,1" newline bitfld.long 0xC 27. "LOOPCTRL_CM_HST_THRESH,Increase Threshold Detection" "0,1" newline bitfld.long 0xC 11.--12. "LP_CMP_ISRC_SEL,Low Power Comparator Current Bias" "0: 50nA,1: 100nA,2: 200nA,3: 400nA" newline hexmask.long.byte 0xC 6.--10. 1. "VBG_TRIM,Trim Bandgap Voltage" newline bitfld.long 0xC 4. "RLOAD_REG_EN_LPSR,Load Resistor Enable" "0: Disconnect load resistor,1: Connect load resistor" newline bitfld.long 0xC 3. "DM_CTRL,DM Control" "0: No change to ripple when the discontinuous..,1: Improves ripple when the inductor current goes.." line.long 0x10 "REG2,DCDC Register 2" bitfld.long 0x10 30. "LOOPCTRL_TOGGLE_DIF,Set high to enable supply stepping to change only after the differential control loop has toggled as well" "0,1" newline bitfld.long 0x10 28. "DCM_SET_CTRL,DCM Set Control" "0,1" newline hexmask.long.word 0x10 16.--25. 1. "BATTMONITOR_BATT_VAL,Software should be configured to place the battery voltage in this register measured with an 8-mV LSB resolution through the ADC" newline bitfld.long 0x10 15. "BATTMONITOR_EN_BATADJ,This bit enables the DCDC to improve efficiency and minimize ripple using the information from the BATT_VAL field" "0,1" newline bitfld.long 0x10 13. "LOOPCTRL_HYST_SIGN,Invert the sign of the hysteresis in DCDC analog comparators." "0,1" newline bitfld.long 0x10 12. "LOOPCTRL_RCSCALE_THRSH,Increase the threshold detection for RC scale circuit." "0,1" newline bitfld.long 0x10 9.--11. "LOOPCTRL_EN_RCSCALE,Enable RC Scale" "0,1,2,3,4,5,6,7" newline bitfld.long 0x10 6.--8. "LOOPCTRL_DC_FF,Two's complement feed forward step in duty cycle in the switching DCDC converter" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x10 2.--5. 1. "LOOPCTRL_DC_R,Magnitude of proportional control parameter in the switching DCDC converter control loop." newline bitfld.long 0x10 0.--1. "LOOPCTRL_DC_C,Ratio of integral control parameter to proportional control parameter in the switching DCDC converter and can be used to optimize efficiency and loop response" "0,1,2,3" line.long 0x14 "REG3,DCDC Register 3" bitfld.long 0x14 30. "VDD1P8CTRL_DISABLE_STEP,Disable Step for VDD1P8" "0: Enable stepping for VDD1P8,1: Disable stepping for VDD1P8" newline bitfld.long 0x14 29. "VDD1P0CTRL_DISABLE_STEP,Disable Step for VDD1P0" "0: Enable stepping for VDD1P0,1: Disable stepping for VDD1P0" newline bitfld.long 0x14 27. "MISC_DELAY_TIMING,Miscellaneous Delay Timing" "0,1" newline bitfld.long 0x14 26. "MINPWR_HALF_FETS,Use half switch FET" "0,1" newline bitfld.long 0x14 24. "MINPWR_DC_HALFCLK,Set DCDC clock to half freqeuncy for continuous mode." "0: DCDC clock remains at full frequency for..,1: DCDC clock set to half frequency for continuous.." newline bitfld.long 0x14 22.--23. "REG_FBK_SEL,Select the feedback point of the internal regulator" "0,1,2,3" newline bitfld.long 0x14 21. "DOUBLE_IBIAS_CMP_LP_LPSR,no description available" "?,1: Double the bias current of the comparator for.." newline bitfld.long 0x14 20. "DISABLE_IDLE_SKIP,no description available" "0: Enable the idle skip function. The DCDC will be..,?" newline bitfld.long 0x14 19. "DISABLE_PULSE_SKIP,Disable Pulse Skip" "0: Stop charging if the duty cycle is lower than..,?" newline bitfld.long 0x14 18. "ENABLE_FF,no description available" "?,1: Enable feed-forward (FF) function that can speed.." newline rbitfld.long 0x14 17. "OVERCUR_DETECT_OUT,signal '1' when overcurrent happens." "?,1: Overcurrent" newline rbitfld.long 0x14 16. "OVERVOLT_VDD1P0_DET_OUT,signal '1' when overvoltage on the VDD1P0 output happens" "?,1: VDD1P0 Overvoltage" newline rbitfld.long 0x14 15. "OVERVOLT_VDD1P8_DET_OUT,signal '1' when overvoltage on the VDD1P8 output happens" "?,1: VDD1P8 Overvoltage" newline rbitfld.long 0x14 14. "IN_BROWNOUT,signal '1' when the voltage on DCDC_IN is lower than 2.6V" "?,1: DCDC_IN is lower than 2.6V" line.long 0x18 "REG4,DCDC Register 4" hexmask.long.word 0x18 0.--15. 1. "ENABLE_SP,Configures CTRL0[ENABLE] (DCDC Enable) for Setpoints 0-15" line.long 0x1C "REG5,DCDC Register 5" hexmask.long.word 0x1C 0.--15. 1. "DIG_EN_SP,Configures CTRL0[DIG_EN] (DCDC_DIG Enable) for Setpoints 0-15. Always set these bits to 1." line.long 0x20 "REG6,DCDC Register 6" hexmask.long.word 0x20 0.--15. 1. "LP_MODE_SP,Configures CTRL0[LP_MODE_EN] (LP Mode Enable) for Setpoints 0-15" line.long 0x24 "REG7,DCDC Register 7" hexmask.long.word 0x24 0.--15. 1. "STBY_EN_SP,Configures CTRL0[STBY_EN] (Standby Enable) for Setpoints 0-15" line.long 0x28 "REG7P,DCDC Register 7 plus" hexmask.long.word 0x28 0.--15. 1. "STBY_LP_MODE_SP,Configures CTRL0[STBY_LP_MODE_EN] (LP Mode via GPC Enable) for Setpoints 0-15" line.long 0x2C "REG8,DCDC Register 8" hexmask.long 0x2C 0.--31. 1. "ANA_TRG_SP0,Configures CTRL1[VDD1P8CTRL_TRG] FOR Setpoints 0-3" line.long 0x30 "REG9,DCDC Register 9" hexmask.long 0x30 0.--31. 1. "ANA_TRG_SP1,Configures CTRL1[VDD1P8CTRL_TRG] FOR Setpoints 4-7" line.long 0x34 "REG10,DCDC Register 10" hexmask.long 0x34 0.--31. 1. "ANA_TRG_SP2,Configures CTRL1[VDD1P8CTRL_TRG] FOR Setpoints 8-11" line.long 0x38 "REG11,DCDC Register 11" hexmask.long 0x38 0.--31. 1. "ANA_TRG_SP3,Configures CTRL1[VDD1P8CTRL_TRG] FOR Setpoints 12-15" line.long 0x3C "REG12,DCDC Register 12" hexmask.long 0x3C 0.--31. 1. "DIG_TRG_SP0,Configures CTRL1[VDD1P0CTRL_TRG] FOR Setpoints 0-3" line.long 0x40 "REG13,DCDC Register 13" hexmask.long 0x40 0.--31. 1. "DIG_TRG_SP1,Configures CTRL1[VDD1P0CTRL_TRG] FOR Setpoints 4-7" line.long 0x44 "REG14,DCDC Register 14" hexmask.long 0x44 0.--31. 1. "DIG_TRG_SP2,Configures CTRL1[VDD1P0CTRL_TRG] FOR Setpoints 8-11" line.long 0x48 "REG15,DCDC Register 15" hexmask.long 0x48 0.--31. 1. "DIG_TRG_SP3,Configures CTRL1[VDD1P0CTRL_TRG] FOR Setpoints 12-15" line.long 0x4C "REG16,DCDC Register 16" hexmask.long 0x4C 0.--31. 1. "ANA_STBY_TRG_SP0,Configures CTRL1[VDD1P8CTRL_STBY_TRG] FOR Setpoints 0-3" line.long 0x50 "REG17,DCDC Register 17" hexmask.long 0x50 0.--31. 1. "ANA_STBY_TRG_SP1,Configures CTRL1[VDD1P8CTRL_STBY_TRG] FOR Setpoints 4-7" line.long 0x54 "REG18,DCDC Register 18" hexmask.long 0x54 0.--31. 1. "ANA_STBY_TRG_SP2,Configures CTRL1[VDD1P8CTRL_STBY_TRG] FOR Setpoints 8-11" line.long 0x58 "REG19,DCDC Register 19" hexmask.long 0x58 0.--31. 1. "ANA_STBY_TRG_SP3,Configures CTRL1[VDD1P8CTRL_STBY_TRG] FOR Setpoints 12-15" line.long 0x5C "REG20,DCDC Register 20" hexmask.long 0x5C 0.--31. 1. "DIG_STBY_TRG_SP0,Configures CTRL1[VDD1P0CTRL_STBY_TRG] FOR Setpoints 0-3" line.long 0x60 "REG21,DCDC Register 21" hexmask.long 0x60 0.--31. 1. "DIG_STBY_TRG_SP1,Configures CTRL1[VDD1P0CTRL_STBY_TRG] FOR Setpoints 4-7" line.long 0x64 "REG22,DCDC Register 22" hexmask.long 0x64 0.--31. 1. "DIG_STBY_TRG_SP2,Configures CTRL1[VDD1P0CTRL_STBY_TRG] FOR Setpoints 8-11" line.long 0x68 "REG23,DCDC Register 23" hexmask.long 0x68 0.--31. 1. "DIG_STBY_TRG_SP3,Configures CTRL1[VDD1P0CTRL_STBY_TRG] FOR Setpoints 12-15" line.long 0x6C "REG24,DCDC Register 24" hexmask.long 0x6C 0.--31. 1. "OK_COUNT,Internal count for dcdc_ok timeout" tree.end tree "DCIC" base ad:0x0 tree "DCIC1" base ad:0x40819000 group.long 0x0++0xB line.long 0x0 "DCICC,DCIC Control Register" bitfld.long 0x0 7. "CLK_POL,DISP_CLK signal polarity." "0: Not inverted (default).,1: Inverted." bitfld.long 0x0 6. "VSYNC_POL,VSYNC_IN signal polarity." "0: Active High.,1: Active Low." newline bitfld.long 0x0 5. "HSYNC_POL,HSYNC_IN signal polarity." "0: Active High.,1: Active Low." bitfld.long 0x0 4. "DE_POL,DATA_EN_IN signal polarity." "0: Active High.,1: Active Low." newline bitfld.long 0x0 0. "IC_EN,Integrity Check enable. Main enable switch." "0: Disabled,1: Enabled" line.long 0x4 "DCICIC,DCIC Interrupt Control Register" bitfld.long 0x4 16. "EXT_SIG_EN,External controller mismatch indication signal." "0: Disabled,1: Enabled" bitfld.long 0x4 3. "FREEZE_MASK,Disable change of interrupt masks. 'Sticky' bit which can be set once and cleared by reset only." "0: Masks change allowed,1: Masks are frozen" newline bitfld.long 0x4 1. "FI_MASK,Functional Interrupt mask. Can be changed only while FREEZE_MASK = 0." "0: Mask disabled - Interrupt assertion enabled,1: Mask enabled - Interrupt assertion disabled" bitfld.long 0x4 0. "EI_MASK,Error Interrupt mask. Can be changed only while FREEZE_MASK = 0." "0: Mask disabled - Interrupt assertion enabled,1: Mask enabled - Interrupt assertion disabled" line.long 0x8 "DCICS,DCIC Status Register" eventfld.long 0x8 17. "FI_STAT,Functional Interrupt status. Write '1' to clear." "0: No pending Interrupt,1: Pending Interrupt" rbitfld.long 0x8 16. "EI_STAT,Error Interrupt status" "0: No pending Interrupt,1: Pending Interrupt" newline hexmask.long.word 0x8 0.--15. 1. "ROI_MATCH_STAT,Each set bit of this field indicates there was a mismatch at the appropriate ROIs signature during the last frame" repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x10)++0x3 line.long 0x0 "DCICRC$1,DCIC ROI Config Register" bitfld.long 0x0 31. "ROI_EN,ROI tracking enable" "0: Disabled,1: Enabled" bitfld.long 0x0 30. "ROI_FREEZE,When set the only parameter of the ROI that can be changed is the reference signature" "0: ROI configuration can be changed,1: ROI configuration is frozen" newline hexmask.long.word 0x0 16.--27. 1. "START_OFFSET_Y,Row number of ROIs upper-left corner (Y coordinate) Range: 0 to 2^12-1" hexmask.long.word 0x0 0.--12. 1. "START_OFFSET_X,Column number of ROIs upper-left corner (X coordinate) Range: 0 to 2^13-1" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x14)++0x3 line.long 0x0 "DCICRS$1,DCIC ROI Size Register" hexmask.long.word 0x0 16.--27. 1. "END_OFFSET_Y,Row number of ROIs lower-right corner (Y coordinate) Range: 1 to 2^12-1" hexmask.long.word 0x0 0.--12. 1. "END_OFFSET_X,Column number of ROIs lower-right corner (X coordinate) Range: 1 to 2^13-1" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x18)++0x3 line.long 0x0 "DCICRRS$1,DCIC ROI Reference Signature Register" hexmask.long 0x0 0.--31. 1. "REFERENCE_SIGNATURE,32-bit expected signature (CRC calculation result) for the ROI" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "DCICRCS$1,DCIC ROI Calculated Signature Register" hexmask.long 0x0 0.--31. 1. "CALCULATED_SIGNATURE,32-bit actual signature (CRC calculation result) for the ROI during the last frame" repeat.end tree.end tree "DCIC2" base ad:0x4081A000 group.long 0x0++0xB line.long 0x0 "DCICC,DCIC Control Register" bitfld.long 0x0 7. "CLK_POL,DISP_CLK signal polarity." "0: Not inverted (default).,1: Inverted." bitfld.long 0x0 6. "VSYNC_POL,VSYNC_IN signal polarity." "0: Active High.,1: Active Low." newline bitfld.long 0x0 5. "HSYNC_POL,HSYNC_IN signal polarity." "0: Active High.,1: Active Low." bitfld.long 0x0 4. "DE_POL,DATA_EN_IN signal polarity." "0: Active High.,1: Active Low." newline bitfld.long 0x0 0. "IC_EN,Integrity Check enable. Main enable switch." "0: Disabled,1: Enabled" line.long 0x4 "DCICIC,DCIC Interrupt Control Register" bitfld.long 0x4 16. "EXT_SIG_EN,External controller mismatch indication signal." "0: Disabled,1: Enabled" bitfld.long 0x4 3. "FREEZE_MASK,Disable change of interrupt masks. 'Sticky' bit which can be set once and cleared by reset only." "0: Masks change allowed,1: Masks are frozen" newline bitfld.long 0x4 1. "FI_MASK,Functional Interrupt mask. Can be changed only while FREEZE_MASK = 0." "0: Mask disabled - Interrupt assertion enabled,1: Mask enabled - Interrupt assertion disabled" bitfld.long 0x4 0. "EI_MASK,Error Interrupt mask. Can be changed only while FREEZE_MASK = 0." "0: Mask disabled - Interrupt assertion enabled,1: Mask enabled - Interrupt assertion disabled" line.long 0x8 "DCICS,DCIC Status Register" eventfld.long 0x8 17. "FI_STAT,Functional Interrupt status. Write '1' to clear." "0: No pending Interrupt,1: Pending Interrupt" rbitfld.long 0x8 16. "EI_STAT,Error Interrupt status" "0: No pending Interrupt,1: Pending Interrupt" newline hexmask.long.word 0x8 0.--15. 1. "ROI_MATCH_STAT,Each set bit of this field indicates there was a mismatch at the appropriate ROIs signature during the last frame" repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x10)++0x3 line.long 0x0 "DCICRC$1,DCIC ROI Config Register" bitfld.long 0x0 31. "ROI_EN,ROI tracking enable" "0: Disabled,1: Enabled" bitfld.long 0x0 30. "ROI_FREEZE,When set the only parameter of the ROI that can be changed is the reference signature" "0: ROI configuration can be changed,1: ROI configuration is frozen" newline hexmask.long.word 0x0 16.--27. 1. "START_OFFSET_Y,Row number of ROIs upper-left corner (Y coordinate) Range: 0 to 2^12-1" hexmask.long.word 0x0 0.--12. 1. "START_OFFSET_X,Column number of ROIs upper-left corner (X coordinate) Range: 0 to 2^13-1" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x14)++0x3 line.long 0x0 "DCICRS$1,DCIC ROI Size Register" hexmask.long.word 0x0 16.--27. 1. "END_OFFSET_Y,Row number of ROIs lower-right corner (Y coordinate) Range: 1 to 2^12-1" hexmask.long.word 0x0 0.--12. 1. "END_OFFSET_X,Column number of ROIs lower-right corner (X coordinate) Range: 1 to 2^13-1" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x18)++0x3 line.long 0x0 "DCICRRS$1,DCIC ROI Reference Signature Register" hexmask.long 0x0 0.--31. 1. "REFERENCE_SIGNATURE,32-bit expected signature (CRC calculation result) for the ROI" repeat.end repeat 16. (increment 0x0 0x1)(increment 0x0 0x10) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "DCICRCS$1,DCIC ROI Calculated Signature Register" hexmask.long 0x0 0.--31. 1. "CALCULATED_SIGNATURE,32-bit actual signature (CRC calculation result) for the ROI during the last frame" repeat.end tree.end tree.end tree "DMA" base ad:0x0 sif (cpuis("IMXRT1163-CM7")||cpuis("IMXRT1165-CM7")) tree "DMA0" base ad:0x40070000 group.long 0x0++0x3 line.long 0x0 "CR,Control" rbitfld.long 0x0 31. "ACTIVE,eDMA Active Status" "0: eDMA is idle,1: eDMA is executing a channel" hexmask.long.byte 0x0 24.--30. 1. "VERSION,eDMA version number" newline bitfld.long 0x0 17. "CX,Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" bitfld.long 0x0 16. "ECX,Error Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" newline bitfld.long 0x0 10. "GRP1PRI,Channel Group 1 Priority" "0,1" bitfld.long 0x0 8. "GRP0PRI,Channel Group 0 Priority" "0,1" newline bitfld.long 0x0 7. "EMLM,Enable Minor Loop Mapping" "0: Disabled,1: Enabled" bitfld.long 0x0 6. "CLM,Continuous Link Mode" "0: Continuous link mode is off,1: Continuous link mode is on" newline bitfld.long 0x0 5. "HALT,Halt eDMA Operations" "0: Normal operation,1: eDMA operations halted" bitfld.long 0x0 4. "HOE,Halt On Error" "0: Normal operation,1: Error causes HALT field to be automatically set.." newline bitfld.long 0x0 3. "ERGA,Enable Round Robin Group Arbitration" "0: Fixed priority arbitration,1: Round robin arbitration" bitfld.long 0x0 2. "ERCA,Enable Round Robin Channel Arbitration" "0: Fixed priority arbitration within each group,1: Round robin arbitration within each group" newline bitfld.long 0x0 1. "EDBG,Enable Debug" "0: When the chip is in Debug mode the eDMA..,1: When the chip is in debug mode the DMA stalls.." rgroup.long 0x4++0x3 line.long 0x0 "ES,Error Status" bitfld.long 0x0 31. "VLD,Logical OR of all ERR status fields" "0: No ERR fields are 1,1: At least one ERR field has a value of 1.." bitfld.long 0x0 16. "ECX,Transfer Canceled" "0: No canceled transfers,1: The most-recently recorded entry was a canceled.." newline bitfld.long 0x0 15. "GPE,Group Priority Error" "0: No group priority error.,1: The most-recently recorded error was a.." bitfld.long 0x0 14. "CPE,Channel Priority Error" "0: No channel priority error.,1: The most-recently recorded error was a.." newline hexmask.long.byte 0x0 8.--12. 1. "ERRCHN,Error Channel Number or Canceled Channel Number" bitfld.long 0x0 7. "SAE,Source Address Error" "0: No source address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 6. "SOE,Source Offset Error" "0: No source offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 5. "DAE,Destination Address Error" "0: No destination address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 4. "DOE,Destination Offset Error" "0: No destination offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 3. "NCE,NBYTES/CITER Configuration Error" "0: No NBYTES/CITER configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 2. "SGE,Scatter/Gather Configuration Error" "0: No scatter/gather configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 1. "SBE,Source Bus Error" "0: No source bus error.,1: The most-recently recorded error was a bus error.." newline bitfld.long 0x0 0. "DBE,Destination Bus Error" "0: No destination bus error.,1: The most-recently recorded error was a bus error.." group.long 0xC++0x3 line.long 0x0 "ERQ,Enable Request" bitfld.long 0x0 31. "ERQ31,Enable DMA Request 31" "0: The DMA request signal for channel 31 is disabled,1: The DMA request signal for channel 31 is enabled" bitfld.long 0x0 30. "ERQ30,Enable DMA Request 30" "0: The DMA request signal for channel 30 is disabled,1: The DMA request signal for channel 30 is enabled" newline bitfld.long 0x0 29. "ERQ29,Enable DMA Request 29" "0: The DMA request signal for channel 29 is disabled,1: The DMA request signal for channel 29 is enabled" bitfld.long 0x0 28. "ERQ28,Enable DMA Request 28" "0: The DMA request signal for channel 28 is disabled,1: The DMA request signal for channel 28 is enabled" newline bitfld.long 0x0 27. "ERQ27,Enable DMA Request 27" "0: The DMA request signal for channel 27 is disabled,1: The DMA request signal for channel 27 is enabled" bitfld.long 0x0 26. "ERQ26,Enable DMA Request 26" "0: The DMA request signal for channel 26 is disabled,1: The DMA request signal for channel 26 is enabled" newline bitfld.long 0x0 25. "ERQ25,Enable DMA Request 25" "0: The DMA request signal for channel 25 is disabled,1: The DMA request signal for channel 25 is enabled" bitfld.long 0x0 24. "ERQ24,Enable DMA Request 24" "0: The DMA request signal for channel 24 is disabled,1: The DMA request signal for channel 24 is enabled" newline bitfld.long 0x0 23. "ERQ23,Enable DMA Request 23" "0: The DMA request signal for channel 23 is disabled,1: The DMA request signal for channel 23 is enabled" bitfld.long 0x0 22. "ERQ22,Enable DMA Request 22" "0: The DMA request signal for channel 22 is disabled,1: The DMA request signal for channel 22 is enabled" newline bitfld.long 0x0 21. "ERQ21,Enable DMA Request 21" "0: The DMA request signal for channel 21 is disabled,1: The DMA request signal for channel 21 is enabled" bitfld.long 0x0 20. "ERQ20,Enable DMA Request 20" "0: The DMA request signal for channel 20 is disabled,1: The DMA request signal for channel 20 is enabled" newline bitfld.long 0x0 19. "ERQ19,Enable DMA Request 19" "0: The DMA request signal for channel 19 is disabled,1: The DMA request signal for channel 19 is enabled" bitfld.long 0x0 18. "ERQ18,Enable DMA Request 18" "0: The DMA request signal for channel 18 is disabled,1: The DMA request signal for channel 18 is enabled" newline bitfld.long 0x0 17. "ERQ17,Enable DMA Request 17" "0: The DMA request signal for channel 17 is disabled,1: The DMA request signal for channel 17 is enabled" bitfld.long 0x0 16. "ERQ16,Enable DMA Request 16" "0: The DMA request signal for channel 16 is disabled,1: The DMA request signal for channel 16 is enabled" newline bitfld.long 0x0 15. "ERQ15,Enable DMA Request 15" "0: The DMA request signal for channel 15 is disabled,1: The DMA request signal for channel 15 is enabled" bitfld.long 0x0 14. "ERQ14,Enable DMA Request 14" "0: The DMA request signal for channel 14 is disabled,1: The DMA request signal for channel 14 is enabled" newline bitfld.long 0x0 13. "ERQ13,Enable DMA Request 13" "0: The DMA request signal for channel 13 is disabled,1: The DMA request signal for channel 13 is enabled" bitfld.long 0x0 12. "ERQ12,Enable DMA Request 12" "0: The DMA request signal for channel 12 is disabled,1: The DMA request signal for channel 12 is enabled" newline bitfld.long 0x0 11. "ERQ11,Enable DMA Request 11" "0: The DMA request signal for channel 11 is disabled,1: The DMA request signal for channel 11 is enabled" bitfld.long 0x0 10. "ERQ10,Enable DMA Request 10" "0: The DMA request signal for channel 10 is disabled,1: The DMA request signal for channel 10 is enabled" newline bitfld.long 0x0 9. "ERQ9,Enable DMA Request 9" "0: The DMA request signal for channel 9 is disabled,1: The DMA request signal for channel 9 is enabled" bitfld.long 0x0 8. "ERQ8,Enable DMA Request 8" "0: The DMA request signal for channel 8 is disabled,1: The DMA request signal for channel 8 is enabled" newline bitfld.long 0x0 7. "ERQ7,Enable DMA Request 7" "0: The DMA request signal for channel 7 is disabled,1: The DMA request signal for channel 7 is enabled" bitfld.long 0x0 6. "ERQ6,Enable DMA Request 6" "0: The DMA request signal for channel 6 is disabled,1: The DMA request signal for channel 6 is enabled" newline bitfld.long 0x0 5. "ERQ5,Enable DMA Request 5" "0: The DMA request signal for channel 5 is disabled,1: The DMA request signal for channel 5 is enabled" bitfld.long 0x0 4. "ERQ4,Enable DMA Request 4" "0: The DMA request signal for channel 4 is disabled,1: The DMA request signal for channel 4 is enabled" newline bitfld.long 0x0 3. "ERQ3,Enable DMA Request 3" "0: The DMA request signal for channel 3 is disabled,1: The DMA request signal for channel 3 is enabled" bitfld.long 0x0 2. "ERQ2,Enable DMA Request 2" "0: The DMA request signal for channel 2 is disabled,1: The DMA request signal for channel 2 is enabled" newline bitfld.long 0x0 1. "ERQ1,Enable DMA Request 1" "0: The DMA request signal for channel 1 is disabled,1: The DMA request signal for channel 1 is enabled" bitfld.long 0x0 0. "ERQ0,Enable DMA Request 0" "0: The DMA request signal for channel 0 is disabled,1: The DMA request signal for channel 0 is enabled" group.long 0x14++0x3 line.long 0x0 "EEI,Enable Error Interrupt" bitfld.long 0x0 31. "EEI31,Enable Error Interrupt 31" "0: An error on channel 31 does not generate an..,1: An error on channel 31 generates an error.." bitfld.long 0x0 30. "EEI30,Enable Error Interrupt 30" "0: An error on channel 30 does not generate an..,1: An error on channel 30 generates an error.." newline bitfld.long 0x0 29. "EEI29,Enable Error Interrupt 29" "0: An error on channel 29 does not generate an..,1: An error on channel 29 generates an error.." bitfld.long 0x0 28. "EEI28,Enable Error Interrupt 28" "0: An error on channel 28 does not generate an..,1: An error on channel 28 generates an error.." newline bitfld.long 0x0 27. "EEI27,Enable Error Interrupt 27" "0: An error on channel 27 does not generate an..,1: An error on channel 27 generates an error.." bitfld.long 0x0 26. "EEI26,Enable Error Interrupt 26" "0: An error on channel 26 does not generate an..,1: An error on channel 26 generates an error.." newline bitfld.long 0x0 25. "EEI25,Enable Error Interrupt 25" "0: An error on channel 25 does not generate an..,1: An error on channel 25 generates an error.." bitfld.long 0x0 24. "EEI24,Enable Error Interrupt 24" "0: An error on channel 24 does not generate an..,1: An error on channel 24 generates an error.." newline bitfld.long 0x0 23. "EEI23,Enable Error Interrupt 23" "0: An error on channel 23 does not generate an..,1: An error on channel 23 generates an error.." bitfld.long 0x0 22. "EEI22,Enable Error Interrupt 22" "0: An error on channel 22 does not generate an..,1: An error on channel 22 generates an error.." newline bitfld.long 0x0 21. "EEI21,Enable Error Interrupt 21" "0: An error on channel 21 does not generate an..,1: An error on channel 21 generates an error.." bitfld.long 0x0 20. "EEI20,Enable Error Interrupt 20" "0: An error on channel 20 does not generate an..,1: An error on channel 20 generates an error.." newline bitfld.long 0x0 19. "EEI19,Enable Error Interrupt 19" "0: An error on channel 19 does not generate an..,1: An error on channel 19 generates an error.." bitfld.long 0x0 18. "EEI18,Enable Error Interrupt 18" "0: An error on channel 18 does not generate an..,1: An error on channel 18 generates an error.." newline bitfld.long 0x0 17. "EEI17,Enable Error Interrupt 17" "0: An error on channel 17 does not generate an..,1: An error on channel 17 generates an error.." bitfld.long 0x0 16. "EEI16,Enable Error Interrupt 16" "0: An error on channel 16 does not generate an..,1: An error on channel 16 generates an error.." newline bitfld.long 0x0 15. "EEI15,Enable Error Interrupt 15" "0: An error on channel 15 does not generate an..,1: An error on channel 15 generates an error.." bitfld.long 0x0 14. "EEI14,Enable Error Interrupt 14" "0: An error on channel 14 does not generate an..,1: An error on channel 14 generates an error.." newline bitfld.long 0x0 13. "EEI13,Enable Error Interrupt 13" "0: An error on channel 13 does not generate an..,1: An error on channel 13 generates an error.." bitfld.long 0x0 12. "EEI12,Enable Error Interrupt 12" "0: An error on channel 12 does not generate an..,1: An error on channel 12 generates an error.." newline bitfld.long 0x0 11. "EEI11,Enable Error Interrupt 11" "0: An error on channel 11 does not generate an..,1: An error on channel 11 generates an error.." bitfld.long 0x0 10. "EEI10,Enable Error Interrupt 10" "0: An error on channel 10 does not generate an..,1: An error on channel 10 generates an error.." newline bitfld.long 0x0 9. "EEI9,Enable Error Interrupt 9" "0: An error on channel 9 does not generate an error..,1: An error on channel 9 generates an error.." bitfld.long 0x0 8. "EEI8,Enable Error Interrupt 8" "0: An error on channel 8 does not generate an error..,1: An error on channel 8 generates an error.." newline bitfld.long 0x0 7. "EEI7,Enable Error Interrupt 7" "0: An error on channel 7 does not generate an error..,1: An error on channel 7 generates an error.." bitfld.long 0x0 6. "EEI6,Enable Error Interrupt 6" "0: An error on channel 6 does not generate an error..,1: An error on channel 6 generates an error.." newline bitfld.long 0x0 5. "EEI5,Enable Error Interrupt 5" "0: An error on channel 5 does not generate an error..,1: An error on channel 5 generates an error.." bitfld.long 0x0 4. "EEI4,Enable Error Interrupt 4" "0: An error on channel 4 does not generate an error..,1: An error on channel 4 generates an error.." newline bitfld.long 0x0 3. "EEI3,Enable Error Interrupt 3" "0: An error on channel 3 does not generate an error..,1: An error on channel 3 generates an error.." bitfld.long 0x0 2. "EEI2,Enable Error Interrupt 2" "0: An error on channel 2 does not generate an error..,1: An error on channel 2 generates an error.." newline bitfld.long 0x0 1. "EEI1,Enable Error Interrupt 1" "0: An error on channel 1 does not generate an error..,1: An error on channel 1 generates an error.." bitfld.long 0x0 0. "EEI0,Enable Error Interrupt 0" "0: An error on channel 0 does not generate an error..,1: An error on channel 0 generates an error.." group.byte 0x18++0x7 line.byte 0x0 "CEEI,Clear Enable Error Interrupt" bitfld.byte 0x0 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x0 6. "CAEE,Clear All Enable Error Interrupts" "0: Write 0 only to the EEI field specified in the..,1: Write 0 to all fields in EEI" newline hexmask.byte 0x0 0.--4. 1. "CEEI,Clear Enable Error Interrupt" line.byte 0x1 "SEEI,Set Enable Error Interrupt" bitfld.byte 0x1 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x1 6. "SAEE,Set All Enable Error Interrupts" "0: Write 1 only to the EEI field specified in the..,1: Writes 1 to all fields in EEI" newline hexmask.byte 0x1 0.--4. 1. "SEEI,Set Enable Error Interrupt" line.byte 0x2 "CERQ,Clear Enable Request" bitfld.byte 0x2 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x2 6. "CAER,Clear All Enable Requests" "0: Write 0 to only the ERQ field specified in the..,1: Write 0 to all fields in ERQ" newline hexmask.byte 0x2 0.--4. 1. "CERQ,Clear Enable Request" line.byte 0x3 "SERQ,Set Enable Request" bitfld.byte 0x3 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x3 6. "SAER,Set All Enable Requests" "0: Write 1 to only the ERQ field specified in the..,1: Write 1 to all fields in ERQ" newline hexmask.byte 0x3 0.--4. 1. "SERQ,Set Enable Request" line.byte 0x4 "CDNE,Clear DONE Status Bit" bitfld.byte 0x4 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x4 6. "CADN,Clears All DONE fields" "0: Writes 0 to only the TCDn_CSR[DONE] field..,1: Writes 0 to all bits in TCDn_CSR[DONE]" newline hexmask.byte 0x4 0.--4. 1. "CDNE,Clear DONE field" line.byte 0x5 "SSRT,Set START Bit" bitfld.byte 0x5 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x5 6. "SAST,Set All START fields (activates all channels)" "0: Write 1 to only the TCDn_CSR[START] field..,1: Write 1 to all bits in TCDn_CSR[START]" newline hexmask.byte 0x5 0.--4. 1. "SSRT,Set START field" line.byte 0x6 "CERR,Clear Error" bitfld.byte 0x6 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x6 6. "CAEI,Clear All Error Indicators" "0: Write 0 to only the ERR field specified in the..,1: Write 0 to all fields in ERR" newline hexmask.byte 0x6 0.--4. 1. "CERR,Clear Error Indicator" line.byte 0x7 "CINT,Clear Interrupt Request" bitfld.byte 0x7 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x7 6. "CAIR,Clear All Interrupt Requests" "0: Clear only the INT field specified in the CINT..,1: Clear all bits in INT" newline hexmask.byte 0x7 0.--4. 1. "CINT,Clear Interrupt Request" group.long 0x24++0x3 line.long 0x0 "INT,Interrupt Request" eventfld.long 0x0 31. "INT31,Interrupt Request 31" "0: The interrupt request for channel 31 is cleared,1: The interrupt request for channel 31 is active" eventfld.long 0x0 30. "INT30,Interrupt Request 30" "0: The interrupt request for channel 30 is cleared,1: The interrupt request for channel 30 is active" newline eventfld.long 0x0 29. "INT29,Interrupt Request 29" "0: The interrupt request for channel 29 is cleared,1: The interrupt request for channel 29 is active" eventfld.long 0x0 28. "INT28,Interrupt Request 28" "0: The interrupt request for channel 28 is cleared,1: The interrupt request for channel 28 is active" newline eventfld.long 0x0 27. "INT27,Interrupt Request 27" "0: The interrupt request for channel 27 is cleared,1: The interrupt request for channel 27 is active" eventfld.long 0x0 26. "INT26,Interrupt Request 26" "0: The interrupt request for channel 26 is cleared,1: The interrupt request for channel 26 is active" newline eventfld.long 0x0 25. "INT25,Interrupt Request 25" "0: The interrupt request for channel 25 is cleared,1: The interrupt request for channel 25 is active" eventfld.long 0x0 24. "INT24,Interrupt Request 24" "0: The interrupt request for channel 24 is cleared,1: The interrupt request for channel 24 is active" newline eventfld.long 0x0 23. "INT23,Interrupt Request 23" "0: The interrupt request for channel 23 is cleared,1: The interrupt request for channel 23 is active" eventfld.long 0x0 22. "INT22,Interrupt Request 22" "0: The interrupt request for channel 22 is cleared,1: The interrupt request for channel 22 is active" newline eventfld.long 0x0 21. "INT21,Interrupt Request 21" "0: The interrupt request for channel 21 is cleared,1: The interrupt request for channel 21 is active" eventfld.long 0x0 20. "INT20,Interrupt Request 20" "0: The interrupt request for channel 20 is cleared,1: The interrupt request for channel 20 is active" newline eventfld.long 0x0 19. "INT19,Interrupt Request 19" "0: The interrupt request for channel 19 is cleared,1: The interrupt request for channel 19 is active" eventfld.long 0x0 18. "INT18,Interrupt Request 18" "0: The interrupt request for channel 18 is cleared,1: The interrupt request for channel 18 is active" newline eventfld.long 0x0 17. "INT17,Interrupt Request 17" "0: The interrupt request for channel 17 is cleared,1: The interrupt request for channel 17 is active" eventfld.long 0x0 16. "INT16,Interrupt Request 16" "0: The interrupt request for channel 16 is cleared,1: The interrupt request for channel 16 is active" newline eventfld.long 0x0 15. "INT15,Interrupt Request 15" "0: The interrupt request for channel 15 is cleared,1: The interrupt request for channel 15 is active" eventfld.long 0x0 14. "INT14,Interrupt Request 14" "0: The interrupt request for channel 14 is cleared,1: The interrupt request for channel 14 is active" newline eventfld.long 0x0 13. "INT13,Interrupt Request 13" "0: The interrupt request for channel 13 is cleared,1: The interrupt request for channel 13 is active" eventfld.long 0x0 12. "INT12,Interrupt Request 12" "0: The interrupt request for channel 12 is cleared,1: The interrupt request for channel 12 is active" newline eventfld.long 0x0 11. "INT11,Interrupt Request 11" "0: The interrupt request for channel 11 is cleared,1: The interrupt request for channel 11 is active" eventfld.long 0x0 10. "INT10,Interrupt Request 10" "0: The interrupt request for channel 10 is cleared,1: The interrupt request for channel 10 is active" newline eventfld.long 0x0 9. "INT9,Interrupt Request 9" "0: The interrupt request for channel 9 is cleared,1: The interrupt request for channel 9 is active" eventfld.long 0x0 8. "INT8,Interrupt Request 8" "0: The interrupt request for channel 8 is cleared,1: The interrupt request for channel 8 is active" newline eventfld.long 0x0 7. "INT7,Interrupt Request 7" "0: The interrupt request for channel 7 is cleared,1: The interrupt request for channel 7 is active" eventfld.long 0x0 6. "INT6,Interrupt Request 6" "0: The interrupt request for channel 6 is cleared,1: The interrupt request for channel 6 is active" newline eventfld.long 0x0 5. "INT5,Interrupt Request 5" "0: The interrupt request for channel 5 is cleared,1: The interrupt request for channel 5 is active" eventfld.long 0x0 4. "INT4,Interrupt Request 4" "0: The interrupt request for channel 4 is cleared,1: The interrupt request for channel 4 is active" newline eventfld.long 0x0 3. "INT3,Interrupt Request 3" "0: The interrupt request for channel 3 is cleared,1: The interrupt request for channel 3 is active" eventfld.long 0x0 2. "INT2,Interrupt Request 2" "0: The interrupt request for channel 2 is cleared,1: The interrupt request for channel 2 is active" newline eventfld.long 0x0 1. "INT1,Interrupt Request 1" "0: The interrupt request for channel 1 is cleared,1: The interrupt request for channel 1 is active" eventfld.long 0x0 0. "INT0,Interrupt Request 0" "0: The interrupt request for channel 0 is cleared,1: The interrupt request for channel 0 is active" group.long 0x2C++0x3 line.long 0x0 "ERR,Error" eventfld.long 0x0 31. "ERR31,Error In Channel 31" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 30. "ERR30,Error In Channel 30" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 29. "ERR29,Error In Channel 29" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 28. "ERR28,Error In Channel 28" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 27. "ERR27,Error In Channel 27" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 26. "ERR26,Error In Channel 26" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 25. "ERR25,Error In Channel 25" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 24. "ERR24,Error In Channel 24" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 23. "ERR23,Error In Channel 23" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 22. "ERR22,Error In Channel 22" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 21. "ERR21,Error In Channel 21" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 20. "ERR20,Error In Channel 20" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 19. "ERR19,Error In Channel 19" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 18. "ERR18,Error In Channel 18" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 17. "ERR17,Error In Channel 17" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 16. "ERR16,Error In Channel 16" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 15. "ERR15,Error In Channel 15" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 14. "ERR14,Error In Channel 14" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 13. "ERR13,Error In Channel 13" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 12. "ERR12,Error In Channel 12" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 11. "ERR11,Error In Channel 11" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 10. "ERR10,Error In Channel 10" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 9. "ERR9,Error In Channel 9" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 8. "ERR8,Error In Channel 8" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 7. "ERR7,Error In Channel 7" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 6. "ERR6,Error In Channel 6" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 5. "ERR5,Error In Channel 5" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 4. "ERR4,Error In Channel 4" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 3. "ERR3,Error In Channel 3" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 2. "ERR2,Error In Channel 2" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 1. "ERR1,Error In Channel 1" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 0. "ERR0,Error In Channel 0" "0: No error in this channel has occurred,1: An error in this channel has occurred" rgroup.long 0x34++0x3 line.long 0x0 "HRS,Hardware Request Status" bitfld.long 0x0 31. "HRS31,Hardware Request Status Channel 31" "0: A hardware service request for channel 31 is not..,1: A hardware service request for channel 31 is.." bitfld.long 0x0 30. "HRS30,Hardware Request Status Channel 30" "0: A hardware service request for channel 30 is not..,1: A hardware service request for channel 30 is.." newline bitfld.long 0x0 29. "HRS29,Hardware Request Status Channel 29" "0: A hardware service request for channel 29 is not..,1: A hardware service request for channel 29 is.." bitfld.long 0x0 28. "HRS28,Hardware Request Status Channel 28" "0: A hardware service request for channel 28 is not..,1: A hardware service request for channel 28 is.." newline bitfld.long 0x0 27. "HRS27,Hardware Request Status Channel 27" "0: A hardware service request for channel 27 is not..,1: A hardware service request for channel 27 is.." bitfld.long 0x0 26. "HRS26,Hardware Request Status Channel 26" "0: A hardware service request for channel 26 is not..,1: A hardware service request for channel 26 is.." newline bitfld.long 0x0 25. "HRS25,Hardware Request Status Channel 25" "0: A hardware service request for channel 25 is not..,1: A hardware service request for channel 25 is.." bitfld.long 0x0 24. "HRS24,Hardware Request Status Channel 24" "0: A hardware service request for channel 24 is not..,1: A hardware service request for channel 24 is.." newline bitfld.long 0x0 23. "HRS23,Hardware Request Status Channel 23" "0: A hardware service request for channel 23 is not..,1: A hardware service request for channel 23 is.." bitfld.long 0x0 22. "HRS22,Hardware Request Status Channel 22" "0: A hardware service request for channel 22 is not..,1: A hardware service request for channel 22 is.." newline bitfld.long 0x0 21. "HRS21,Hardware Request Status Channel 21" "0: A hardware service request for channel 21 is not..,1: A hardware service request for channel 21 is.." bitfld.long 0x0 20. "HRS20,Hardware Request Status Channel 20" "0: A hardware service request for channel 20 is not..,1: A hardware service request for channel 20 is.." newline bitfld.long 0x0 19. "HRS19,Hardware Request Status Channel 19" "0: A hardware service request for channel 19 is not..,1: A hardware service request for channel 19 is.." bitfld.long 0x0 18. "HRS18,Hardware Request Status Channel 18" "0: A hardware service request for channel 18 is not..,1: A hardware service request for channel 18 is.." newline bitfld.long 0x0 17. "HRS17,Hardware Request Status Channel 17" "0: A hardware service request for channel 17 is not..,1: A hardware service request for channel 17 is.." bitfld.long 0x0 16. "HRS16,Hardware Request Status Channel 16" "0: A hardware service request for channel 16 is not..,1: A hardware service request for channel 16 is.." newline bitfld.long 0x0 15. "HRS15,Hardware Request Status Channel 15" "0: A hardware service request for channel 15 is not..,1: A hardware service request for channel 15 is.." bitfld.long 0x0 14. "HRS14,Hardware Request Status Channel 14" "0: A hardware service request for channel 14 is not..,1: A hardware service request for channel 14 is.." newline bitfld.long 0x0 13. "HRS13,Hardware Request Status Channel 13" "0: A hardware service request for channel 13 is not..,1: A hardware service request for channel 13 is.." bitfld.long 0x0 12. "HRS12,Hardware Request Status Channel 12" "0: A hardware service request for channel 12 is not..,1: A hardware service request for channel 12 is.." newline bitfld.long 0x0 11. "HRS11,Hardware Request Status Channel 11" "0: A hardware service request for channel 11 is not..,1: A hardware service request for channel 11 is.." bitfld.long 0x0 10. "HRS10,Hardware Request Status Channel 10" "0: A hardware service request for channel 10 is not..,1: A hardware service request for channel 10 is.." newline bitfld.long 0x0 9. "HRS9,Hardware Request Status Channel 9" "0: A hardware service request for channel 9 is not..,1: A hardware service request for channel 9 is.." bitfld.long 0x0 8. "HRS8,Hardware Request Status Channel 8" "0: A hardware service request for channel 8 is not..,1: A hardware service request for channel 8 is.." newline bitfld.long 0x0 7. "HRS7,Hardware Request Status Channel 7" "0: A hardware service request for channel 7 is not..,1: A hardware service request for channel 7 is.." bitfld.long 0x0 6. "HRS6,Hardware Request Status Channel 6" "0: A hardware service request for channel 6 is not..,1: A hardware service request for channel 6 is.." newline bitfld.long 0x0 5. "HRS5,Hardware Request Status Channel 5" "0: A hardware service request for channel 5 is not..,1: A hardware service request for channel 5 is.." bitfld.long 0x0 4. "HRS4,Hardware Request Status Channel 4" "0: A hardware service request for channel 4 is not..,1: A hardware service request for channel 4 is.." newline bitfld.long 0x0 3. "HRS3,Hardware Request Status Channel 3" "0: A hardware service request for channel 3 is not..,1: A hardware service request for channel 3 is.." bitfld.long 0x0 2. "HRS2,Hardware Request Status Channel 2" "0: A hardware service request for channel 2 is not..,1: A hardware service request for channel 2 is.." newline bitfld.long 0x0 1. "HRS1,Hardware Request Status Channel 1" "0: A hardware service request for channel 1 is not..,1: A hardware service request for channel 1 is.." bitfld.long 0x0 0. "HRS0,Hardware Request Status Channel 0" "0: A hardware service request for channel 0 is not..,1: A hardware service request for channel 0 is.." group.long 0x44++0x3 line.long 0x0 "EARS,Enable Asynchronous Request in Stop" bitfld.long 0x0 31. "EDREQ_31,Enable asynchronous DMA request in stop mode for channel 31." "0: Disable asynchronous DMA request for channel 31,1: Enable asynchronous DMA request for channel 31" bitfld.long 0x0 30. "EDREQ_30,Enable asynchronous DMA request in stop mode for channel 30." "0: Disable asynchronous DMA request for channel 30,1: Enable asynchronous DMA request for channel 30" newline bitfld.long 0x0 29. "EDREQ_29,Enable asynchronous DMA request in stop mode for channel 29." "0: Disable asynchronous DMA request for channel 29,1: Enable asynchronous DMA request for channel 29" bitfld.long 0x0 28. "EDREQ_28,Enable asynchronous DMA request in stop mode for channel 28." "0: Disable asynchronous DMA request for channel 28,1: Enable asynchronous DMA request for channel 28" newline bitfld.long 0x0 27. "EDREQ_27,Enable asynchronous DMA request in stop mode for channel 27." "0: Disable asynchronous DMA request for channel 27,1: Enable asynchronous DMA request for channel 27" bitfld.long 0x0 26. "EDREQ_26,Enable asynchronous DMA request in stop mode for channel 26." "0: Disable asynchronous DMA request for channel 26,1: Enable asynchronous DMA request for channel 26" newline bitfld.long 0x0 25. "EDREQ_25,Enable asynchronous DMA request in stop mode for channel 25." "0: Disable asynchronous DMA request for channel 25,1: Enable asynchronous DMA request for channel 25" bitfld.long 0x0 24. "EDREQ_24,Enable asynchronous DMA request in stop mode for channel 24." "0: Disable asynchronous DMA request for channel 24,1: Enable asynchronous DMA request for channel 24" newline bitfld.long 0x0 23. "EDREQ_23,Enable asynchronous DMA request in stop mode for channel 23." "0: Disable asynchronous DMA request for channel 23,1: Enable asynchronous DMA request for channel 23" bitfld.long 0x0 22. "EDREQ_22,Enable asynchronous DMA request in stop mode for channel 22." "0: Disable asynchronous DMA request for channel 22,1: Enable asynchronous DMA request for channel 22" newline bitfld.long 0x0 21. "EDREQ_21,Enable asynchronous DMA request in stop mode for channel 21." "0: Disable asynchronous DMA request for channel 21,1: Enable asynchronous DMA request for channel 21" bitfld.long 0x0 20. "EDREQ_20,Enable asynchronous DMA request in stop mode for channel 20." "0: Disable asynchronous DMA request for channel 20,1: Enable asynchronous DMA request for channel 20" newline bitfld.long 0x0 19. "EDREQ_19,Enable asynchronous DMA request in stop mode for channel 19." "0: Disable asynchronous DMA request for channel 19,1: Enable asynchronous DMA request for channel 19" bitfld.long 0x0 18. "EDREQ_18,Enable asynchronous DMA request in stop mode for channel 18." "0: Disable asynchronous DMA request for channel 18,1: Enable asynchronous DMA request for channel 18" newline bitfld.long 0x0 17. "EDREQ_17,Enable asynchronous DMA request in stop mode for channel 17." "0: Disable asynchronous DMA request for channel 17,1: Enable asynchronous DMA request for channel 17" bitfld.long 0x0 16. "EDREQ_16,Enable asynchronous DMA request in stop mode for channel 16." "0: Disable asynchronous DMA request for channel 16,1: Enable asynchronous DMA request for channel 16" newline bitfld.long 0x0 15. "EDREQ_15,Enable asynchronous DMA request in stop mode for channel 15." "0: Disable asynchronous DMA request for channel 15,1: Enable asynchronous DMA request for channel 15" bitfld.long 0x0 14. "EDREQ_14,Enable asynchronous DMA request in stop mode for channel 14." "0: Disable asynchronous DMA request for channel 14,1: Enable asynchronous DMA request for channel 14" newline bitfld.long 0x0 13. "EDREQ_13,Enable asynchronous DMA request in stop mode for channel 13." "0: Disable asynchronous DMA request for channel 13,1: Enable asynchronous DMA request for channel 13" bitfld.long 0x0 12. "EDREQ_12,Enable asynchronous DMA request in stop mode for channel 12." "0: Disable asynchronous DMA request for channel 12,1: Enable asynchronous DMA request for channel 12" newline bitfld.long 0x0 11. "EDREQ_11,Enable asynchronous DMA request in stop mode for channel 11." "0: Disable asynchronous DMA request for channel 11,1: Enable asynchronous DMA request for channel 11" bitfld.long 0x0 10. "EDREQ_10,Enable asynchronous DMA request in stop mode for channel 10." "0: Disable asynchronous DMA request for channel 10,1: Enable asynchronous DMA request for channel 10" newline bitfld.long 0x0 9. "EDREQ_9,Enable asynchronous DMA request in stop mode for channel 9." "0: Disable asynchronous DMA request for channel 9,1: Enable asynchronous DMA request for channel 9" bitfld.long 0x0 8. "EDREQ_8,Enable asynchronous DMA request in stop mode for channel 8." "0: Disable asynchronous DMA request for channel 8,1: Enable asynchronous DMA request for channel 8" newline bitfld.long 0x0 7. "EDREQ_7,Enable asynchronous DMA request in stop mode for channel 7." "0: Disable asynchronous DMA request for channel 7,1: Enable asynchronous DMA request for channel 7" bitfld.long 0x0 6. "EDREQ_6,Enable asynchronous DMA request in stop mode for channel 6." "0: Disable asynchronous DMA request for channel 6,1: Enable asynchronous DMA request for channel 6" newline bitfld.long 0x0 5. "EDREQ_5,Enable asynchronous DMA request in stop mode for channel 5." "0: Disable asynchronous DMA request for channel 5,1: Enable asynchronous DMA request for channel 5" bitfld.long 0x0 4. "EDREQ_4,Enable asynchronous DMA request in stop mode for channel 4." "0: Disable asynchronous DMA request for channel 4,1: Enable asynchronous DMA request for channel 4" newline bitfld.long 0x0 3. "EDREQ_3,Enable asynchronous DMA request in stop mode for channel 3." "0: Disable asynchronous DMA request for channel 3,1: Enable asynchronous DMA request for channel 3" bitfld.long 0x0 2. "EDREQ_2,Enable asynchronous DMA request in stop mode for channel 2." "0: Disable asynchronous DMA request for channel 2,1: Enable asynchronous DMA request for channel 2" newline bitfld.long 0x0 1. "EDREQ_1,Enable asynchronous DMA request in stop mode for channel 1." "0: Disable asynchronous DMA request for channel 1,1: Enable asynchronous DMA request for channel 1" bitfld.long 0x0 0. "EDREQ_0,Enable asynchronous DMA request in stop mode for channel 0." "0: Disable asynchronous DMA request for channel 0,1: Enable asynchronous DMA request for channel 0" group.byte 0x100++0x1F line.byte 0x0 "DCHPRI3,Channel Priority" bitfld.byte 0x0 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x0 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x0 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x0 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1 "DCHPRI2,Channel Priority" bitfld.byte 0x1 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x2 "DCHPRI1,Channel Priority" bitfld.byte 0x2 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x2 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x2 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x2 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x3 "DCHPRI0,Channel Priority" bitfld.byte 0x3 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x3 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x3 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x3 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x4 "DCHPRI7,Channel Priority" bitfld.byte 0x4 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x4 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x4 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x4 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x5 "DCHPRI6,Channel Priority" bitfld.byte 0x5 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x5 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x5 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x5 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x6 "DCHPRI5,Channel Priority" bitfld.byte 0x6 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x6 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x6 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x6 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x7 "DCHPRI4,Channel Priority" bitfld.byte 0x7 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x7 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x7 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x7 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x8 "DCHPRI11,Channel Priority" bitfld.byte 0x8 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x8 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x8 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x8 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x9 "DCHPRI10,Channel Priority" bitfld.byte 0x9 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x9 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x9 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x9 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xA "DCHPRI9,Channel Priority" bitfld.byte 0xA 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xA 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xA 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xA 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xB "DCHPRI8,Channel Priority" bitfld.byte 0xB 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xB 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xB 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xB 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xC "DCHPRI15,Channel Priority" bitfld.byte 0xC 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xC 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xC 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xC 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xD "DCHPRI14,Channel Priority" bitfld.byte 0xD 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xD 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xD 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xD 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xE "DCHPRI13,Channel Priority" bitfld.byte 0xE 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xE 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xE 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xE 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xF "DCHPRI12,Channel Priority" bitfld.byte 0xF 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xF 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xF 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xF 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x10 "DCHPRI19,Channel Priority" bitfld.byte 0x10 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x10 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x10 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x10 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x11 "DCHPRI18,Channel Priority" bitfld.byte 0x11 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x11 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x11 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x11 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x12 "DCHPRI17,Channel Priority" bitfld.byte 0x12 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x12 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x12 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x12 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x13 "DCHPRI16,Channel Priority" bitfld.byte 0x13 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x13 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x13 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x13 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x14 "DCHPRI23,Channel Priority" bitfld.byte 0x14 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x14 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x14 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x14 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x15 "DCHPRI22,Channel Priority" bitfld.byte 0x15 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x15 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x15 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x15 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x16 "DCHPRI21,Channel Priority" bitfld.byte 0x16 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x16 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x16 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x16 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x17 "DCHPRI20,Channel Priority" bitfld.byte 0x17 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x17 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x17 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x17 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x18 "DCHPRI27,Channel Priority" bitfld.byte 0x18 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x18 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x18 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x18 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x19 "DCHPRI26,Channel Priority" bitfld.byte 0x19 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x19 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x19 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x19 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1A "DCHPRI25,Channel Priority" bitfld.byte 0x1A 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1A 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1A 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1A 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1B "DCHPRI24,Channel Priority" bitfld.byte 0x1B 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1B 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1B 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1B 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1C "DCHPRI31,Channel Priority" bitfld.byte 0x1C 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1C 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1C 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1C 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1D "DCHPRI30,Channel Priority" bitfld.byte 0x1D 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1D 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1D 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1D 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1E "DCHPRI29,Channel Priority" bitfld.byte 0x1E 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1E 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1E 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1E 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1F "DCHPRI28,Channel Priority" bitfld.byte 0x1F 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1F 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1F 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1F 0.--3. 1. "CHPRI,Channel n Arbitration Priority" group.long 0x1000++0x3 line.long 0x0 "TCD0_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1004++0x3 line.word 0x0 "TCD0_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD0_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0xB line.long 0x0 "TCD0_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD0_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD0_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1014++0x3 line.word 0x0 "TCD0_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD0_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1016++0x1 line.word 0x0 "TCD0_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1018++0x3 line.long 0x0 "TCD0_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x101C++0x3 line.word 0x0 "TCD0_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD0_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x101E++0x1 line.word 0x0 "TCD0_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1020++0x3 line.long 0x0 "TCD1_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1024++0x3 line.word 0x0 "TCD1_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD1_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0xB line.long 0x0 "TCD1_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD1_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD1_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1034++0x3 line.word 0x0 "TCD1_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD1_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1036++0x1 line.word 0x0 "TCD1_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1038++0x3 line.long 0x0 "TCD1_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x103C++0x3 line.word 0x0 "TCD1_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD1_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x103E++0x1 line.word 0x0 "TCD1_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1040++0x3 line.long 0x0 "TCD2_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1044++0x3 line.word 0x0 "TCD2_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD2_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0xB line.long 0x0 "TCD2_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD2_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD2_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1054++0x3 line.word 0x0 "TCD2_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD2_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1056++0x1 line.word 0x0 "TCD2_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1058++0x3 line.long 0x0 "TCD2_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x105C++0x3 line.word 0x0 "TCD2_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD2_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x105E++0x1 line.word 0x0 "TCD2_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1060++0x3 line.long 0x0 "TCD3_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1064++0x3 line.word 0x0 "TCD3_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD3_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0xB line.long 0x0 "TCD3_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD3_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD3_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1074++0x3 line.word 0x0 "TCD3_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD3_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1076++0x1 line.word 0x0 "TCD3_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1078++0x3 line.long 0x0 "TCD3_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x107C++0x3 line.word 0x0 "TCD3_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD3_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x107E++0x1 line.word 0x0 "TCD3_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1080++0x3 line.long 0x0 "TCD4_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1084++0x3 line.word 0x0 "TCD4_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD4_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0xB line.long 0x0 "TCD4_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD4_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD4_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1094++0x3 line.word 0x0 "TCD4_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD4_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1096++0x1 line.word 0x0 "TCD4_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1098++0x3 line.long 0x0 "TCD4_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x109C++0x3 line.word 0x0 "TCD4_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD4_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x109E++0x1 line.word 0x0 "TCD4_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10A0++0x3 line.long 0x0 "TCD5_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10A4++0x3 line.word 0x0 "TCD5_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD5_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0xB line.long 0x0 "TCD5_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD5_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD5_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10B4++0x3 line.word 0x0 "TCD5_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD5_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10B6++0x1 line.word 0x0 "TCD5_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10B8++0x3 line.long 0x0 "TCD5_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10BC++0x3 line.word 0x0 "TCD5_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD5_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10BE++0x1 line.word 0x0 "TCD5_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10C0++0x3 line.long 0x0 "TCD6_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10C4++0x3 line.word 0x0 "TCD6_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD6_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0xB line.long 0x0 "TCD6_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD6_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD6_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10D4++0x3 line.word 0x0 "TCD6_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD6_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10D6++0x1 line.word 0x0 "TCD6_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10D8++0x3 line.long 0x0 "TCD6_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10DC++0x3 line.word 0x0 "TCD6_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD6_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10DE++0x1 line.word 0x0 "TCD6_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10E0++0x3 line.long 0x0 "TCD7_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10E4++0x3 line.word 0x0 "TCD7_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD7_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0xB line.long 0x0 "TCD7_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD7_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD7_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10F4++0x3 line.word 0x0 "TCD7_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD7_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10F6++0x1 line.word 0x0 "TCD7_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10F8++0x3 line.long 0x0 "TCD7_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10FC++0x3 line.word 0x0 "TCD7_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD7_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10FE++0x1 line.word 0x0 "TCD7_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1100++0x3 line.long 0x0 "TCD8_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1104++0x3 line.word 0x0 "TCD8_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD8_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0xB line.long 0x0 "TCD8_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD8_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD8_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1114++0x3 line.word 0x0 "TCD8_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD8_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1116++0x1 line.word 0x0 "TCD8_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1118++0x3 line.long 0x0 "TCD8_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x111C++0x3 line.word 0x0 "TCD8_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD8_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x111E++0x1 line.word 0x0 "TCD8_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1120++0x3 line.long 0x0 "TCD9_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1124++0x3 line.word 0x0 "TCD9_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD9_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0xB line.long 0x0 "TCD9_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD9_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD9_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1134++0x3 line.word 0x0 "TCD9_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD9_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1136++0x1 line.word 0x0 "TCD9_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1138++0x3 line.long 0x0 "TCD9_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x113C++0x3 line.word 0x0 "TCD9_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD9_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x113E++0x1 line.word 0x0 "TCD9_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1140++0x3 line.long 0x0 "TCD10_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1144++0x3 line.word 0x0 "TCD10_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD10_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0xB line.long 0x0 "TCD10_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD10_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD10_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1154++0x3 line.word 0x0 "TCD10_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD10_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1156++0x1 line.word 0x0 "TCD10_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1158++0x3 line.long 0x0 "TCD10_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x115C++0x3 line.word 0x0 "TCD10_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD10_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x115E++0x1 line.word 0x0 "TCD10_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1160++0x3 line.long 0x0 "TCD11_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1164++0x3 line.word 0x0 "TCD11_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD11_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0xB line.long 0x0 "TCD11_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD11_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD11_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1174++0x3 line.word 0x0 "TCD11_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD11_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1176++0x1 line.word 0x0 "TCD11_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1178++0x3 line.long 0x0 "TCD11_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x117C++0x3 line.word 0x0 "TCD11_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD11_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x117E++0x1 line.word 0x0 "TCD11_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1180++0x3 line.long 0x0 "TCD12_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1184++0x3 line.word 0x0 "TCD12_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD12_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0xB line.long 0x0 "TCD12_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD12_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD12_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1194++0x3 line.word 0x0 "TCD12_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD12_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1196++0x1 line.word 0x0 "TCD12_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1198++0x3 line.long 0x0 "TCD12_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x119C++0x3 line.word 0x0 "TCD12_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD12_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x119E++0x1 line.word 0x0 "TCD12_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11A0++0x3 line.long 0x0 "TCD13_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11A4++0x3 line.word 0x0 "TCD13_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD13_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0xB line.long 0x0 "TCD13_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD13_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD13_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11B4++0x3 line.word 0x0 "TCD13_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD13_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11B6++0x1 line.word 0x0 "TCD13_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11B8++0x3 line.long 0x0 "TCD13_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11BC++0x3 line.word 0x0 "TCD13_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD13_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11BE++0x1 line.word 0x0 "TCD13_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11C0++0x3 line.long 0x0 "TCD14_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11C4++0x3 line.word 0x0 "TCD14_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD14_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0xB line.long 0x0 "TCD14_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD14_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD14_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11D4++0x3 line.word 0x0 "TCD14_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD14_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11D6++0x1 line.word 0x0 "TCD14_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11D8++0x3 line.long 0x0 "TCD14_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11DC++0x3 line.word 0x0 "TCD14_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD14_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11DE++0x1 line.word 0x0 "TCD14_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11E0++0x3 line.long 0x0 "TCD15_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11E4++0x3 line.word 0x0 "TCD15_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD15_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0xB line.long 0x0 "TCD15_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD15_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD15_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11F4++0x3 line.word 0x0 "TCD15_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD15_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11F6++0x1 line.word 0x0 "TCD15_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11F8++0x3 line.long 0x0 "TCD15_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11FC++0x3 line.word 0x0 "TCD15_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD15_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11FE++0x1 line.word 0x0 "TCD15_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1200++0x3 line.long 0x0 "TCD16_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1204++0x3 line.word 0x0 "TCD16_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD16_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0xB line.long 0x0 "TCD16_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD16_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD16_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1214++0x3 line.word 0x0 "TCD16_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD16_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1216++0x1 line.word 0x0 "TCD16_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1218++0x3 line.long 0x0 "TCD16_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x121C++0x3 line.word 0x0 "TCD16_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD16_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x121E++0x1 line.word 0x0 "TCD16_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1220++0x3 line.long 0x0 "TCD17_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1224++0x3 line.word 0x0 "TCD17_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD17_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0xB line.long 0x0 "TCD17_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD17_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD17_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1234++0x3 line.word 0x0 "TCD17_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD17_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1236++0x1 line.word 0x0 "TCD17_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1238++0x3 line.long 0x0 "TCD17_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x123C++0x3 line.word 0x0 "TCD17_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD17_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x123E++0x1 line.word 0x0 "TCD17_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1240++0x3 line.long 0x0 "TCD18_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1244++0x3 line.word 0x0 "TCD18_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD18_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0xB line.long 0x0 "TCD18_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD18_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD18_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1254++0x3 line.word 0x0 "TCD18_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD18_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1256++0x1 line.word 0x0 "TCD18_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1258++0x3 line.long 0x0 "TCD18_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x125C++0x3 line.word 0x0 "TCD18_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD18_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x125E++0x1 line.word 0x0 "TCD18_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1260++0x3 line.long 0x0 "TCD19_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1264++0x3 line.word 0x0 "TCD19_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD19_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0xB line.long 0x0 "TCD19_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD19_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD19_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1274++0x3 line.word 0x0 "TCD19_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD19_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1276++0x1 line.word 0x0 "TCD19_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1278++0x3 line.long 0x0 "TCD19_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x127C++0x3 line.word 0x0 "TCD19_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD19_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x127E++0x1 line.word 0x0 "TCD19_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1280++0x3 line.long 0x0 "TCD20_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1284++0x3 line.word 0x0 "TCD20_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD20_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0xB line.long 0x0 "TCD20_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD20_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD20_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1294++0x3 line.word 0x0 "TCD20_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD20_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1296++0x1 line.word 0x0 "TCD20_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1298++0x3 line.long 0x0 "TCD20_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x129C++0x3 line.word 0x0 "TCD20_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD20_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x129E++0x1 line.word 0x0 "TCD20_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12A0++0x3 line.long 0x0 "TCD21_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12A4++0x3 line.word 0x0 "TCD21_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD21_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0xB line.long 0x0 "TCD21_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD21_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD21_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12B4++0x3 line.word 0x0 "TCD21_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD21_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12B6++0x1 line.word 0x0 "TCD21_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12B8++0x3 line.long 0x0 "TCD21_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12BC++0x3 line.word 0x0 "TCD21_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD21_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12BE++0x1 line.word 0x0 "TCD21_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12C0++0x3 line.long 0x0 "TCD22_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12C4++0x3 line.word 0x0 "TCD22_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD22_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0xB line.long 0x0 "TCD22_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD22_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD22_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12D4++0x3 line.word 0x0 "TCD22_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD22_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12D6++0x1 line.word 0x0 "TCD22_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12D8++0x3 line.long 0x0 "TCD22_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12DC++0x3 line.word 0x0 "TCD22_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD22_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12DE++0x1 line.word 0x0 "TCD22_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12E0++0x3 line.long 0x0 "TCD23_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12E4++0x3 line.word 0x0 "TCD23_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD23_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0xB line.long 0x0 "TCD23_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD23_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD23_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12F4++0x3 line.word 0x0 "TCD23_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD23_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12F6++0x1 line.word 0x0 "TCD23_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12F8++0x3 line.long 0x0 "TCD23_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12FC++0x3 line.word 0x0 "TCD23_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD23_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12FE++0x1 line.word 0x0 "TCD23_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1300++0x3 line.long 0x0 "TCD24_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1304++0x3 line.word 0x0 "TCD24_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD24_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0xB line.long 0x0 "TCD24_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD24_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD24_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1314++0x3 line.word 0x0 "TCD24_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD24_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1316++0x1 line.word 0x0 "TCD24_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1318++0x3 line.long 0x0 "TCD24_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x131C++0x3 line.word 0x0 "TCD24_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD24_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x131E++0x1 line.word 0x0 "TCD24_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1320++0x3 line.long 0x0 "TCD25_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1324++0x3 line.word 0x0 "TCD25_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD25_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0xB line.long 0x0 "TCD25_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD25_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD25_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1334++0x3 line.word 0x0 "TCD25_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD25_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1336++0x1 line.word 0x0 "TCD25_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1338++0x3 line.long 0x0 "TCD25_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x133C++0x3 line.word 0x0 "TCD25_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD25_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x133E++0x1 line.word 0x0 "TCD25_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1340++0x3 line.long 0x0 "TCD26_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1344++0x3 line.word 0x0 "TCD26_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD26_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0xB line.long 0x0 "TCD26_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD26_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD26_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1354++0x3 line.word 0x0 "TCD26_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD26_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1356++0x1 line.word 0x0 "TCD26_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1358++0x3 line.long 0x0 "TCD26_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x135C++0x3 line.word 0x0 "TCD26_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD26_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x135E++0x1 line.word 0x0 "TCD26_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1360++0x3 line.long 0x0 "TCD27_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1364++0x3 line.word 0x0 "TCD27_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD27_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0xB line.long 0x0 "TCD27_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD27_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD27_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1374++0x3 line.word 0x0 "TCD27_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD27_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1376++0x1 line.word 0x0 "TCD27_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1378++0x3 line.long 0x0 "TCD27_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x137C++0x3 line.word 0x0 "TCD27_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD27_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x137E++0x1 line.word 0x0 "TCD27_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1380++0x3 line.long 0x0 "TCD28_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1384++0x3 line.word 0x0 "TCD28_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD28_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0xB line.long 0x0 "TCD28_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD28_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD28_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1394++0x3 line.word 0x0 "TCD28_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD28_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1396++0x1 line.word 0x0 "TCD28_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1398++0x3 line.long 0x0 "TCD28_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x139C++0x3 line.word 0x0 "TCD28_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD28_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x139E++0x1 line.word 0x0 "TCD28_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13A0++0x3 line.long 0x0 "TCD29_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13A4++0x3 line.word 0x0 "TCD29_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD29_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0xB line.long 0x0 "TCD29_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD29_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD29_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13B4++0x3 line.word 0x0 "TCD29_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD29_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13B6++0x1 line.word 0x0 "TCD29_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13B8++0x3 line.long 0x0 "TCD29_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13BC++0x3 line.word 0x0 "TCD29_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD29_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13BE++0x1 line.word 0x0 "TCD29_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13C0++0x3 line.long 0x0 "TCD30_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13C4++0x3 line.word 0x0 "TCD30_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD30_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0xB line.long 0x0 "TCD30_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD30_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD30_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13D4++0x3 line.word 0x0 "TCD30_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD30_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13D6++0x1 line.word 0x0 "TCD30_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13D8++0x3 line.long 0x0 "TCD30_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13DC++0x3 line.word 0x0 "TCD30_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD30_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13DE++0x1 line.word 0x0 "TCD30_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13E0++0x3 line.long 0x0 "TCD31_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13E4++0x3 line.word 0x0 "TCD31_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD31_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0xB line.long 0x0 "TCD31_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD31_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD31_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13F4++0x3 line.word 0x0 "TCD31_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD31_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13F6++0x1 line.word 0x0 "TCD31_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13F8++0x3 line.long 0x0 "TCD31_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13FC++0x3 line.word 0x0 "TCD31_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD31_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13FE++0x1 line.word 0x0 "TCD31_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" tree.end endif sif (cpuis("IMXRT1165-CM4")) tree "DMA1" base ad:0x40C14000 group.long 0x0++0x3 line.long 0x0 "CR,Control" rbitfld.long 0x0 31. "ACTIVE,eDMA Active Status" "0: eDMA is idle,1: eDMA is executing a channel" hexmask.long.byte 0x0 24.--30. 1. "VERSION,eDMA version number" newline bitfld.long 0x0 17. "CX,Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" bitfld.long 0x0 16. "ECX,Error Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" newline bitfld.long 0x0 10. "GRP1PRI,Channel Group 1 Priority" "0,1" bitfld.long 0x0 8. "GRP0PRI,Channel Group 0 Priority" "0,1" newline bitfld.long 0x0 7. "EMLM,Enable Minor Loop Mapping" "0: Disabled,1: Enabled" bitfld.long 0x0 6. "CLM,Continuous Link Mode" "0: Continuous link mode is off,1: Continuous link mode is on" newline bitfld.long 0x0 5. "HALT,Halt eDMA Operations" "0: Normal operation,1: eDMA operations halted" bitfld.long 0x0 4. "HOE,Halt On Error" "0: Normal operation,1: Error causes HALT field to be automatically set.." newline bitfld.long 0x0 3. "ERGA,Enable Round Robin Group Arbitration" "0: Fixed priority arbitration,1: Round robin arbitration" bitfld.long 0x0 2. "ERCA,Enable Round Robin Channel Arbitration" "0: Fixed priority arbitration within each group,1: Round robin arbitration within each group" newline bitfld.long 0x0 1. "EDBG,Enable Debug" "0: When the chip is in Debug mode the eDMA..,1: When the chip is in debug mode the DMA stalls.." rgroup.long 0x4++0x3 line.long 0x0 "ES,Error Status" bitfld.long 0x0 31. "VLD,Logical OR of all ERR status fields" "0: No ERR fields are 1,1: At least one ERR field has a value of 1.." bitfld.long 0x0 16. "ECX,Transfer Canceled" "0: No canceled transfers,1: The most-recently recorded entry was a canceled.." newline bitfld.long 0x0 15. "GPE,Group Priority Error" "0: No group priority error.,1: The most-recently recorded error was a.." bitfld.long 0x0 14. "CPE,Channel Priority Error" "0: No channel priority error.,1: The most-recently recorded error was a.." newline hexmask.long.byte 0x0 8.--12. 1. "ERRCHN,Error Channel Number or Canceled Channel Number" bitfld.long 0x0 7. "SAE,Source Address Error" "0: No source address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 6. "SOE,Source Offset Error" "0: No source offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 5. "DAE,Destination Address Error" "0: No destination address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 4. "DOE,Destination Offset Error" "0: No destination offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 3. "NCE,NBYTES/CITER Configuration Error" "0: No NBYTES/CITER configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 2. "SGE,Scatter/Gather Configuration Error" "0: No scatter/gather configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 1. "SBE,Source Bus Error" "0: No source bus error.,1: The most-recently recorded error was a bus error.." newline bitfld.long 0x0 0. "DBE,Destination Bus Error" "0: No destination bus error.,1: The most-recently recorded error was a bus error.." group.long 0xC++0x3 line.long 0x0 "ERQ,Enable Request" bitfld.long 0x0 31. "ERQ31,Enable DMA Request 31" "0: The DMA request signal for channel 31 is disabled,1: The DMA request signal for channel 31 is enabled" bitfld.long 0x0 30. "ERQ30,Enable DMA Request 30" "0: The DMA request signal for channel 30 is disabled,1: The DMA request signal for channel 30 is enabled" newline bitfld.long 0x0 29. "ERQ29,Enable DMA Request 29" "0: The DMA request signal for channel 29 is disabled,1: The DMA request signal for channel 29 is enabled" bitfld.long 0x0 28. "ERQ28,Enable DMA Request 28" "0: The DMA request signal for channel 28 is disabled,1: The DMA request signal for channel 28 is enabled" newline bitfld.long 0x0 27. "ERQ27,Enable DMA Request 27" "0: The DMA request signal for channel 27 is disabled,1: The DMA request signal for channel 27 is enabled" bitfld.long 0x0 26. "ERQ26,Enable DMA Request 26" "0: The DMA request signal for channel 26 is disabled,1: The DMA request signal for channel 26 is enabled" newline bitfld.long 0x0 25. "ERQ25,Enable DMA Request 25" "0: The DMA request signal for channel 25 is disabled,1: The DMA request signal for channel 25 is enabled" bitfld.long 0x0 24. "ERQ24,Enable DMA Request 24" "0: The DMA request signal for channel 24 is disabled,1: The DMA request signal for channel 24 is enabled" newline bitfld.long 0x0 23. "ERQ23,Enable DMA Request 23" "0: The DMA request signal for channel 23 is disabled,1: The DMA request signal for channel 23 is enabled" bitfld.long 0x0 22. "ERQ22,Enable DMA Request 22" "0: The DMA request signal for channel 22 is disabled,1: The DMA request signal for channel 22 is enabled" newline bitfld.long 0x0 21. "ERQ21,Enable DMA Request 21" "0: The DMA request signal for channel 21 is disabled,1: The DMA request signal for channel 21 is enabled" bitfld.long 0x0 20. "ERQ20,Enable DMA Request 20" "0: The DMA request signal for channel 20 is disabled,1: The DMA request signal for channel 20 is enabled" newline bitfld.long 0x0 19. "ERQ19,Enable DMA Request 19" "0: The DMA request signal for channel 19 is disabled,1: The DMA request signal for channel 19 is enabled" bitfld.long 0x0 18. "ERQ18,Enable DMA Request 18" "0: The DMA request signal for channel 18 is disabled,1: The DMA request signal for channel 18 is enabled" newline bitfld.long 0x0 17. "ERQ17,Enable DMA Request 17" "0: The DMA request signal for channel 17 is disabled,1: The DMA request signal for channel 17 is enabled" bitfld.long 0x0 16. "ERQ16,Enable DMA Request 16" "0: The DMA request signal for channel 16 is disabled,1: The DMA request signal for channel 16 is enabled" newline bitfld.long 0x0 15. "ERQ15,Enable DMA Request 15" "0: The DMA request signal for channel 15 is disabled,1: The DMA request signal for channel 15 is enabled" bitfld.long 0x0 14. "ERQ14,Enable DMA Request 14" "0: The DMA request signal for channel 14 is disabled,1: The DMA request signal for channel 14 is enabled" newline bitfld.long 0x0 13. "ERQ13,Enable DMA Request 13" "0: The DMA request signal for channel 13 is disabled,1: The DMA request signal for channel 13 is enabled" bitfld.long 0x0 12. "ERQ12,Enable DMA Request 12" "0: The DMA request signal for channel 12 is disabled,1: The DMA request signal for channel 12 is enabled" newline bitfld.long 0x0 11. "ERQ11,Enable DMA Request 11" "0: The DMA request signal for channel 11 is disabled,1: The DMA request signal for channel 11 is enabled" bitfld.long 0x0 10. "ERQ10,Enable DMA Request 10" "0: The DMA request signal for channel 10 is disabled,1: The DMA request signal for channel 10 is enabled" newline bitfld.long 0x0 9. "ERQ9,Enable DMA Request 9" "0: The DMA request signal for channel 9 is disabled,1: The DMA request signal for channel 9 is enabled" bitfld.long 0x0 8. "ERQ8,Enable DMA Request 8" "0: The DMA request signal for channel 8 is disabled,1: The DMA request signal for channel 8 is enabled" newline bitfld.long 0x0 7. "ERQ7,Enable DMA Request 7" "0: The DMA request signal for channel 7 is disabled,1: The DMA request signal for channel 7 is enabled" bitfld.long 0x0 6. "ERQ6,Enable DMA Request 6" "0: The DMA request signal for channel 6 is disabled,1: The DMA request signal for channel 6 is enabled" newline bitfld.long 0x0 5. "ERQ5,Enable DMA Request 5" "0: The DMA request signal for channel 5 is disabled,1: The DMA request signal for channel 5 is enabled" bitfld.long 0x0 4. "ERQ4,Enable DMA Request 4" "0: The DMA request signal for channel 4 is disabled,1: The DMA request signal for channel 4 is enabled" newline bitfld.long 0x0 3. "ERQ3,Enable DMA Request 3" "0: The DMA request signal for channel 3 is disabled,1: The DMA request signal for channel 3 is enabled" bitfld.long 0x0 2. "ERQ2,Enable DMA Request 2" "0: The DMA request signal for channel 2 is disabled,1: The DMA request signal for channel 2 is enabled" newline bitfld.long 0x0 1. "ERQ1,Enable DMA Request 1" "0: The DMA request signal for channel 1 is disabled,1: The DMA request signal for channel 1 is enabled" bitfld.long 0x0 0. "ERQ0,Enable DMA Request 0" "0: The DMA request signal for channel 0 is disabled,1: The DMA request signal for channel 0 is enabled" group.long 0x14++0x3 line.long 0x0 "EEI,Enable Error Interrupt" bitfld.long 0x0 31. "EEI31,Enable Error Interrupt 31" "0: An error on channel 31 does not generate an..,1: An error on channel 31 generates an error.." bitfld.long 0x0 30. "EEI30,Enable Error Interrupt 30" "0: An error on channel 30 does not generate an..,1: An error on channel 30 generates an error.." newline bitfld.long 0x0 29. "EEI29,Enable Error Interrupt 29" "0: An error on channel 29 does not generate an..,1: An error on channel 29 generates an error.." bitfld.long 0x0 28. "EEI28,Enable Error Interrupt 28" "0: An error on channel 28 does not generate an..,1: An error on channel 28 generates an error.." newline bitfld.long 0x0 27. "EEI27,Enable Error Interrupt 27" "0: An error on channel 27 does not generate an..,1: An error on channel 27 generates an error.." bitfld.long 0x0 26. "EEI26,Enable Error Interrupt 26" "0: An error on channel 26 does not generate an..,1: An error on channel 26 generates an error.." newline bitfld.long 0x0 25. "EEI25,Enable Error Interrupt 25" "0: An error on channel 25 does not generate an..,1: An error on channel 25 generates an error.." bitfld.long 0x0 24. "EEI24,Enable Error Interrupt 24" "0: An error on channel 24 does not generate an..,1: An error on channel 24 generates an error.." newline bitfld.long 0x0 23. "EEI23,Enable Error Interrupt 23" "0: An error on channel 23 does not generate an..,1: An error on channel 23 generates an error.." bitfld.long 0x0 22. "EEI22,Enable Error Interrupt 22" "0: An error on channel 22 does not generate an..,1: An error on channel 22 generates an error.." newline bitfld.long 0x0 21. "EEI21,Enable Error Interrupt 21" "0: An error on channel 21 does not generate an..,1: An error on channel 21 generates an error.." bitfld.long 0x0 20. "EEI20,Enable Error Interrupt 20" "0: An error on channel 20 does not generate an..,1: An error on channel 20 generates an error.." newline bitfld.long 0x0 19. "EEI19,Enable Error Interrupt 19" "0: An error on channel 19 does not generate an..,1: An error on channel 19 generates an error.." bitfld.long 0x0 18. "EEI18,Enable Error Interrupt 18" "0: An error on channel 18 does not generate an..,1: An error on channel 18 generates an error.." newline bitfld.long 0x0 17. "EEI17,Enable Error Interrupt 17" "0: An error on channel 17 does not generate an..,1: An error on channel 17 generates an error.." bitfld.long 0x0 16. "EEI16,Enable Error Interrupt 16" "0: An error on channel 16 does not generate an..,1: An error on channel 16 generates an error.." newline bitfld.long 0x0 15. "EEI15,Enable Error Interrupt 15" "0: An error on channel 15 does not generate an..,1: An error on channel 15 generates an error.." bitfld.long 0x0 14. "EEI14,Enable Error Interrupt 14" "0: An error on channel 14 does not generate an..,1: An error on channel 14 generates an error.." newline bitfld.long 0x0 13. "EEI13,Enable Error Interrupt 13" "0: An error on channel 13 does not generate an..,1: An error on channel 13 generates an error.." bitfld.long 0x0 12. "EEI12,Enable Error Interrupt 12" "0: An error on channel 12 does not generate an..,1: An error on channel 12 generates an error.." newline bitfld.long 0x0 11. "EEI11,Enable Error Interrupt 11" "0: An error on channel 11 does not generate an..,1: An error on channel 11 generates an error.." bitfld.long 0x0 10. "EEI10,Enable Error Interrupt 10" "0: An error on channel 10 does not generate an..,1: An error on channel 10 generates an error.." newline bitfld.long 0x0 9. "EEI9,Enable Error Interrupt 9" "0: An error on channel 9 does not generate an error..,1: An error on channel 9 generates an error.." bitfld.long 0x0 8. "EEI8,Enable Error Interrupt 8" "0: An error on channel 8 does not generate an error..,1: An error on channel 8 generates an error.." newline bitfld.long 0x0 7. "EEI7,Enable Error Interrupt 7" "0: An error on channel 7 does not generate an error..,1: An error on channel 7 generates an error.." bitfld.long 0x0 6. "EEI6,Enable Error Interrupt 6" "0: An error on channel 6 does not generate an error..,1: An error on channel 6 generates an error.." newline bitfld.long 0x0 5. "EEI5,Enable Error Interrupt 5" "0: An error on channel 5 does not generate an error..,1: An error on channel 5 generates an error.." bitfld.long 0x0 4. "EEI4,Enable Error Interrupt 4" "0: An error on channel 4 does not generate an error..,1: An error on channel 4 generates an error.." newline bitfld.long 0x0 3. "EEI3,Enable Error Interrupt 3" "0: An error on channel 3 does not generate an error..,1: An error on channel 3 generates an error.." bitfld.long 0x0 2. "EEI2,Enable Error Interrupt 2" "0: An error on channel 2 does not generate an error..,1: An error on channel 2 generates an error.." newline bitfld.long 0x0 1. "EEI1,Enable Error Interrupt 1" "0: An error on channel 1 does not generate an error..,1: An error on channel 1 generates an error.." bitfld.long 0x0 0. "EEI0,Enable Error Interrupt 0" "0: An error on channel 0 does not generate an error..,1: An error on channel 0 generates an error.." group.byte 0x18++0x7 line.byte 0x0 "CEEI,Clear Enable Error Interrupt" bitfld.byte 0x0 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x0 6. "CAEE,Clear All Enable Error Interrupts" "0: Write 0 only to the EEI field specified in the..,1: Write 0 to all fields in EEI" newline hexmask.byte 0x0 0.--4. 1. "CEEI,Clear Enable Error Interrupt" line.byte 0x1 "SEEI,Set Enable Error Interrupt" bitfld.byte 0x1 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x1 6. "SAEE,Set All Enable Error Interrupts" "0: Write 1 only to the EEI field specified in the..,1: Writes 1 to all fields in EEI" newline hexmask.byte 0x1 0.--4. 1. "SEEI,Set Enable Error Interrupt" line.byte 0x2 "CERQ,Clear Enable Request" bitfld.byte 0x2 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x2 6. "CAER,Clear All Enable Requests" "0: Write 0 to only the ERQ field specified in the..,1: Write 0 to all fields in ERQ" newline hexmask.byte 0x2 0.--4. 1. "CERQ,Clear Enable Request" line.byte 0x3 "SERQ,Set Enable Request" bitfld.byte 0x3 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x3 6. "SAER,Set All Enable Requests" "0: Write 1 to only the ERQ field specified in the..,1: Write 1 to all fields in ERQ" newline hexmask.byte 0x3 0.--4. 1. "SERQ,Set Enable Request" line.byte 0x4 "CDNE,Clear DONE Status Bit" bitfld.byte 0x4 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x4 6. "CADN,Clears All DONE fields" "0: Writes 0 to only the TCDn_CSR[DONE] field..,1: Writes 0 to all bits in TCDn_CSR[DONE]" newline hexmask.byte 0x4 0.--4. 1. "CDNE,Clear DONE field" line.byte 0x5 "SSRT,Set START Bit" bitfld.byte 0x5 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x5 6. "SAST,Set All START fields (activates all channels)" "0: Write 1 to only the TCDn_CSR[START] field..,1: Write 1 to all bits in TCDn_CSR[START]" newline hexmask.byte 0x5 0.--4. 1. "SSRT,Set START field" line.byte 0x6 "CERR,Clear Error" bitfld.byte 0x6 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x6 6. "CAEI,Clear All Error Indicators" "0: Write 0 to only the ERR field specified in the..,1: Write 0 to all fields in ERR" newline hexmask.byte 0x6 0.--4. 1. "CERR,Clear Error Indicator" line.byte 0x7 "CINT,Clear Interrupt Request" bitfld.byte 0x7 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x7 6. "CAIR,Clear All Interrupt Requests" "0: Clear only the INT field specified in the CINT..,1: Clear all bits in INT" newline hexmask.byte 0x7 0.--4. 1. "CINT,Clear Interrupt Request" group.long 0x24++0x3 line.long 0x0 "INT,Interrupt Request" eventfld.long 0x0 31. "INT31,Interrupt Request 31" "0: The interrupt request for channel 31 is cleared,1: The interrupt request for channel 31 is active" eventfld.long 0x0 30. "INT30,Interrupt Request 30" "0: The interrupt request for channel 30 is cleared,1: The interrupt request for channel 30 is active" newline eventfld.long 0x0 29. "INT29,Interrupt Request 29" "0: The interrupt request for channel 29 is cleared,1: The interrupt request for channel 29 is active" eventfld.long 0x0 28. "INT28,Interrupt Request 28" "0: The interrupt request for channel 28 is cleared,1: The interrupt request for channel 28 is active" newline eventfld.long 0x0 27. "INT27,Interrupt Request 27" "0: The interrupt request for channel 27 is cleared,1: The interrupt request for channel 27 is active" eventfld.long 0x0 26. "INT26,Interrupt Request 26" "0: The interrupt request for channel 26 is cleared,1: The interrupt request for channel 26 is active" newline eventfld.long 0x0 25. "INT25,Interrupt Request 25" "0: The interrupt request for channel 25 is cleared,1: The interrupt request for channel 25 is active" eventfld.long 0x0 24. "INT24,Interrupt Request 24" "0: The interrupt request for channel 24 is cleared,1: The interrupt request for channel 24 is active" newline eventfld.long 0x0 23. "INT23,Interrupt Request 23" "0: The interrupt request for channel 23 is cleared,1: The interrupt request for channel 23 is active" eventfld.long 0x0 22. "INT22,Interrupt Request 22" "0: The interrupt request for channel 22 is cleared,1: The interrupt request for channel 22 is active" newline eventfld.long 0x0 21. "INT21,Interrupt Request 21" "0: The interrupt request for channel 21 is cleared,1: The interrupt request for channel 21 is active" eventfld.long 0x0 20. "INT20,Interrupt Request 20" "0: The interrupt request for channel 20 is cleared,1: The interrupt request for channel 20 is active" newline eventfld.long 0x0 19. "INT19,Interrupt Request 19" "0: The interrupt request for channel 19 is cleared,1: The interrupt request for channel 19 is active" eventfld.long 0x0 18. "INT18,Interrupt Request 18" "0: The interrupt request for channel 18 is cleared,1: The interrupt request for channel 18 is active" newline eventfld.long 0x0 17. "INT17,Interrupt Request 17" "0: The interrupt request for channel 17 is cleared,1: The interrupt request for channel 17 is active" eventfld.long 0x0 16. "INT16,Interrupt Request 16" "0: The interrupt request for channel 16 is cleared,1: The interrupt request for channel 16 is active" newline eventfld.long 0x0 15. "INT15,Interrupt Request 15" "0: The interrupt request for channel 15 is cleared,1: The interrupt request for channel 15 is active" eventfld.long 0x0 14. "INT14,Interrupt Request 14" "0: The interrupt request for channel 14 is cleared,1: The interrupt request for channel 14 is active" newline eventfld.long 0x0 13. "INT13,Interrupt Request 13" "0: The interrupt request for channel 13 is cleared,1: The interrupt request for channel 13 is active" eventfld.long 0x0 12. "INT12,Interrupt Request 12" "0: The interrupt request for channel 12 is cleared,1: The interrupt request for channel 12 is active" newline eventfld.long 0x0 11. "INT11,Interrupt Request 11" "0: The interrupt request for channel 11 is cleared,1: The interrupt request for channel 11 is active" eventfld.long 0x0 10. "INT10,Interrupt Request 10" "0: The interrupt request for channel 10 is cleared,1: The interrupt request for channel 10 is active" newline eventfld.long 0x0 9. "INT9,Interrupt Request 9" "0: The interrupt request for channel 9 is cleared,1: The interrupt request for channel 9 is active" eventfld.long 0x0 8. "INT8,Interrupt Request 8" "0: The interrupt request for channel 8 is cleared,1: The interrupt request for channel 8 is active" newline eventfld.long 0x0 7. "INT7,Interrupt Request 7" "0: The interrupt request for channel 7 is cleared,1: The interrupt request for channel 7 is active" eventfld.long 0x0 6. "INT6,Interrupt Request 6" "0: The interrupt request for channel 6 is cleared,1: The interrupt request for channel 6 is active" newline eventfld.long 0x0 5. "INT5,Interrupt Request 5" "0: The interrupt request for channel 5 is cleared,1: The interrupt request for channel 5 is active" eventfld.long 0x0 4. "INT4,Interrupt Request 4" "0: The interrupt request for channel 4 is cleared,1: The interrupt request for channel 4 is active" newline eventfld.long 0x0 3. "INT3,Interrupt Request 3" "0: The interrupt request for channel 3 is cleared,1: The interrupt request for channel 3 is active" eventfld.long 0x0 2. "INT2,Interrupt Request 2" "0: The interrupt request for channel 2 is cleared,1: The interrupt request for channel 2 is active" newline eventfld.long 0x0 1. "INT1,Interrupt Request 1" "0: The interrupt request for channel 1 is cleared,1: The interrupt request for channel 1 is active" eventfld.long 0x0 0. "INT0,Interrupt Request 0" "0: The interrupt request for channel 0 is cleared,1: The interrupt request for channel 0 is active" group.long 0x2C++0x3 line.long 0x0 "ERR,Error" eventfld.long 0x0 31. "ERR31,Error In Channel 31" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 30. "ERR30,Error In Channel 30" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 29. "ERR29,Error In Channel 29" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 28. "ERR28,Error In Channel 28" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 27. "ERR27,Error In Channel 27" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 26. "ERR26,Error In Channel 26" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 25. "ERR25,Error In Channel 25" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 24. "ERR24,Error In Channel 24" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 23. "ERR23,Error In Channel 23" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 22. "ERR22,Error In Channel 22" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 21. "ERR21,Error In Channel 21" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 20. "ERR20,Error In Channel 20" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 19. "ERR19,Error In Channel 19" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 18. "ERR18,Error In Channel 18" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 17. "ERR17,Error In Channel 17" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 16. "ERR16,Error In Channel 16" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 15. "ERR15,Error In Channel 15" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 14. "ERR14,Error In Channel 14" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 13. "ERR13,Error In Channel 13" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 12. "ERR12,Error In Channel 12" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 11. "ERR11,Error In Channel 11" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 10. "ERR10,Error In Channel 10" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 9. "ERR9,Error In Channel 9" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 8. "ERR8,Error In Channel 8" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 7. "ERR7,Error In Channel 7" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 6. "ERR6,Error In Channel 6" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 5. "ERR5,Error In Channel 5" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 4. "ERR4,Error In Channel 4" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 3. "ERR3,Error In Channel 3" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 2. "ERR2,Error In Channel 2" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 1. "ERR1,Error In Channel 1" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 0. "ERR0,Error In Channel 0" "0: No error in this channel has occurred,1: An error in this channel has occurred" rgroup.long 0x34++0x3 line.long 0x0 "HRS,Hardware Request Status" bitfld.long 0x0 31. "HRS31,Hardware Request Status Channel 31" "0: A hardware service request for channel 31 is not..,1: A hardware service request for channel 31 is.." bitfld.long 0x0 30. "HRS30,Hardware Request Status Channel 30" "0: A hardware service request for channel 30 is not..,1: A hardware service request for channel 30 is.." newline bitfld.long 0x0 29. "HRS29,Hardware Request Status Channel 29" "0: A hardware service request for channel 29 is not..,1: A hardware service request for channel 29 is.." bitfld.long 0x0 28. "HRS28,Hardware Request Status Channel 28" "0: A hardware service request for channel 28 is not..,1: A hardware service request for channel 28 is.." newline bitfld.long 0x0 27. "HRS27,Hardware Request Status Channel 27" "0: A hardware service request for channel 27 is not..,1: A hardware service request for channel 27 is.." bitfld.long 0x0 26. "HRS26,Hardware Request Status Channel 26" "0: A hardware service request for channel 26 is not..,1: A hardware service request for channel 26 is.." newline bitfld.long 0x0 25. "HRS25,Hardware Request Status Channel 25" "0: A hardware service request for channel 25 is not..,1: A hardware service request for channel 25 is.." bitfld.long 0x0 24. "HRS24,Hardware Request Status Channel 24" "0: A hardware service request for channel 24 is not..,1: A hardware service request for channel 24 is.." newline bitfld.long 0x0 23. "HRS23,Hardware Request Status Channel 23" "0: A hardware service request for channel 23 is not..,1: A hardware service request for channel 23 is.." bitfld.long 0x0 22. "HRS22,Hardware Request Status Channel 22" "0: A hardware service request for channel 22 is not..,1: A hardware service request for channel 22 is.." newline bitfld.long 0x0 21. "HRS21,Hardware Request Status Channel 21" "0: A hardware service request for channel 21 is not..,1: A hardware service request for channel 21 is.." bitfld.long 0x0 20. "HRS20,Hardware Request Status Channel 20" "0: A hardware service request for channel 20 is not..,1: A hardware service request for channel 20 is.." newline bitfld.long 0x0 19. "HRS19,Hardware Request Status Channel 19" "0: A hardware service request for channel 19 is not..,1: A hardware service request for channel 19 is.." bitfld.long 0x0 18. "HRS18,Hardware Request Status Channel 18" "0: A hardware service request for channel 18 is not..,1: A hardware service request for channel 18 is.." newline bitfld.long 0x0 17. "HRS17,Hardware Request Status Channel 17" "0: A hardware service request for channel 17 is not..,1: A hardware service request for channel 17 is.." bitfld.long 0x0 16. "HRS16,Hardware Request Status Channel 16" "0: A hardware service request for channel 16 is not..,1: A hardware service request for channel 16 is.." newline bitfld.long 0x0 15. "HRS15,Hardware Request Status Channel 15" "0: A hardware service request for channel 15 is not..,1: A hardware service request for channel 15 is.." bitfld.long 0x0 14. "HRS14,Hardware Request Status Channel 14" "0: A hardware service request for channel 14 is not..,1: A hardware service request for channel 14 is.." newline bitfld.long 0x0 13. "HRS13,Hardware Request Status Channel 13" "0: A hardware service request for channel 13 is not..,1: A hardware service request for channel 13 is.." bitfld.long 0x0 12. "HRS12,Hardware Request Status Channel 12" "0: A hardware service request for channel 12 is not..,1: A hardware service request for channel 12 is.." newline bitfld.long 0x0 11. "HRS11,Hardware Request Status Channel 11" "0: A hardware service request for channel 11 is not..,1: A hardware service request for channel 11 is.." bitfld.long 0x0 10. "HRS10,Hardware Request Status Channel 10" "0: A hardware service request for channel 10 is not..,1: A hardware service request for channel 10 is.." newline bitfld.long 0x0 9. "HRS9,Hardware Request Status Channel 9" "0: A hardware service request for channel 9 is not..,1: A hardware service request for channel 9 is.." bitfld.long 0x0 8. "HRS8,Hardware Request Status Channel 8" "0: A hardware service request for channel 8 is not..,1: A hardware service request for channel 8 is.." newline bitfld.long 0x0 7. "HRS7,Hardware Request Status Channel 7" "0: A hardware service request for channel 7 is not..,1: A hardware service request for channel 7 is.." bitfld.long 0x0 6. "HRS6,Hardware Request Status Channel 6" "0: A hardware service request for channel 6 is not..,1: A hardware service request for channel 6 is.." newline bitfld.long 0x0 5. "HRS5,Hardware Request Status Channel 5" "0: A hardware service request for channel 5 is not..,1: A hardware service request for channel 5 is.." bitfld.long 0x0 4. "HRS4,Hardware Request Status Channel 4" "0: A hardware service request for channel 4 is not..,1: A hardware service request for channel 4 is.." newline bitfld.long 0x0 3. "HRS3,Hardware Request Status Channel 3" "0: A hardware service request for channel 3 is not..,1: A hardware service request for channel 3 is.." bitfld.long 0x0 2. "HRS2,Hardware Request Status Channel 2" "0: A hardware service request for channel 2 is not..,1: A hardware service request for channel 2 is.." newline bitfld.long 0x0 1. "HRS1,Hardware Request Status Channel 1" "0: A hardware service request for channel 1 is not..,1: A hardware service request for channel 1 is.." bitfld.long 0x0 0. "HRS0,Hardware Request Status Channel 0" "0: A hardware service request for channel 0 is not..,1: A hardware service request for channel 0 is.." group.long 0x44++0x3 line.long 0x0 "EARS,Enable Asynchronous Request in Stop" bitfld.long 0x0 31. "EDREQ_31,Enable asynchronous DMA request in stop mode for channel 31." "0: Disable asynchronous DMA request for channel 31,1: Enable asynchronous DMA request for channel 31" bitfld.long 0x0 30. "EDREQ_30,Enable asynchronous DMA request in stop mode for channel 30." "0: Disable asynchronous DMA request for channel 30,1: Enable asynchronous DMA request for channel 30" newline bitfld.long 0x0 29. "EDREQ_29,Enable asynchronous DMA request in stop mode for channel 29." "0: Disable asynchronous DMA request for channel 29,1: Enable asynchronous DMA request for channel 29" bitfld.long 0x0 28. "EDREQ_28,Enable asynchronous DMA request in stop mode for channel 28." "0: Disable asynchronous DMA request for channel 28,1: Enable asynchronous DMA request for channel 28" newline bitfld.long 0x0 27. "EDREQ_27,Enable asynchronous DMA request in stop mode for channel 27." "0: Disable asynchronous DMA request for channel 27,1: Enable asynchronous DMA request for channel 27" bitfld.long 0x0 26. "EDREQ_26,Enable asynchronous DMA request in stop mode for channel 26." "0: Disable asynchronous DMA request for channel 26,1: Enable asynchronous DMA request for channel 26" newline bitfld.long 0x0 25. "EDREQ_25,Enable asynchronous DMA request in stop mode for channel 25." "0: Disable asynchronous DMA request for channel 25,1: Enable asynchronous DMA request for channel 25" bitfld.long 0x0 24. "EDREQ_24,Enable asynchronous DMA request in stop mode for channel 24." "0: Disable asynchronous DMA request for channel 24,1: Enable asynchronous DMA request for channel 24" newline bitfld.long 0x0 23. "EDREQ_23,Enable asynchronous DMA request in stop mode for channel 23." "0: Disable asynchronous DMA request for channel 23,1: Enable asynchronous DMA request for channel 23" bitfld.long 0x0 22. "EDREQ_22,Enable asynchronous DMA request in stop mode for channel 22." "0: Disable asynchronous DMA request for channel 22,1: Enable asynchronous DMA request for channel 22" newline bitfld.long 0x0 21. "EDREQ_21,Enable asynchronous DMA request in stop mode for channel 21." "0: Disable asynchronous DMA request for channel 21,1: Enable asynchronous DMA request for channel 21" bitfld.long 0x0 20. "EDREQ_20,Enable asynchronous DMA request in stop mode for channel 20." "0: Disable asynchronous DMA request for channel 20,1: Enable asynchronous DMA request for channel 20" newline bitfld.long 0x0 19. "EDREQ_19,Enable asynchronous DMA request in stop mode for channel 19." "0: Disable asynchronous DMA request for channel 19,1: Enable asynchronous DMA request for channel 19" bitfld.long 0x0 18. "EDREQ_18,Enable asynchronous DMA request in stop mode for channel 18." "0: Disable asynchronous DMA request for channel 18,1: Enable asynchronous DMA request for channel 18" newline bitfld.long 0x0 17. "EDREQ_17,Enable asynchronous DMA request in stop mode for channel 17." "0: Disable asynchronous DMA request for channel 17,1: Enable asynchronous DMA request for channel 17" bitfld.long 0x0 16. "EDREQ_16,Enable asynchronous DMA request in stop mode for channel 16." "0: Disable asynchronous DMA request for channel 16,1: Enable asynchronous DMA request for channel 16" newline bitfld.long 0x0 15. "EDREQ_15,Enable asynchronous DMA request in stop mode for channel 15." "0: Disable asynchronous DMA request for channel 15,1: Enable asynchronous DMA request for channel 15" bitfld.long 0x0 14. "EDREQ_14,Enable asynchronous DMA request in stop mode for channel 14." "0: Disable asynchronous DMA request for channel 14,1: Enable asynchronous DMA request for channel 14" newline bitfld.long 0x0 13. "EDREQ_13,Enable asynchronous DMA request in stop mode for channel 13." "0: Disable asynchronous DMA request for channel 13,1: Enable asynchronous DMA request for channel 13" bitfld.long 0x0 12. "EDREQ_12,Enable asynchronous DMA request in stop mode for channel 12." "0: Disable asynchronous DMA request for channel 12,1: Enable asynchronous DMA request for channel 12" newline bitfld.long 0x0 11. "EDREQ_11,Enable asynchronous DMA request in stop mode for channel 11." "0: Disable asynchronous DMA request for channel 11,1: Enable asynchronous DMA request for channel 11" bitfld.long 0x0 10. "EDREQ_10,Enable asynchronous DMA request in stop mode for channel 10." "0: Disable asynchronous DMA request for channel 10,1: Enable asynchronous DMA request for channel 10" newline bitfld.long 0x0 9. "EDREQ_9,Enable asynchronous DMA request in stop mode for channel 9." "0: Disable asynchronous DMA request for channel 9,1: Enable asynchronous DMA request for channel 9" bitfld.long 0x0 8. "EDREQ_8,Enable asynchronous DMA request in stop mode for channel 8." "0: Disable asynchronous DMA request for channel 8,1: Enable asynchronous DMA request for channel 8" newline bitfld.long 0x0 7. "EDREQ_7,Enable asynchronous DMA request in stop mode for channel 7." "0: Disable asynchronous DMA request for channel 7,1: Enable asynchronous DMA request for channel 7" bitfld.long 0x0 6. "EDREQ_6,Enable asynchronous DMA request in stop mode for channel 6." "0: Disable asynchronous DMA request for channel 6,1: Enable asynchronous DMA request for channel 6" newline bitfld.long 0x0 5. "EDREQ_5,Enable asynchronous DMA request in stop mode for channel 5." "0: Disable asynchronous DMA request for channel 5,1: Enable asynchronous DMA request for channel 5" bitfld.long 0x0 4. "EDREQ_4,Enable asynchronous DMA request in stop mode for channel 4." "0: Disable asynchronous DMA request for channel 4,1: Enable asynchronous DMA request for channel 4" newline bitfld.long 0x0 3. "EDREQ_3,Enable asynchronous DMA request in stop mode for channel 3." "0: Disable asynchronous DMA request for channel 3,1: Enable asynchronous DMA request for channel 3" bitfld.long 0x0 2. "EDREQ_2,Enable asynchronous DMA request in stop mode for channel 2." "0: Disable asynchronous DMA request for channel 2,1: Enable asynchronous DMA request for channel 2" newline bitfld.long 0x0 1. "EDREQ_1,Enable asynchronous DMA request in stop mode for channel 1." "0: Disable asynchronous DMA request for channel 1,1: Enable asynchronous DMA request for channel 1" bitfld.long 0x0 0. "EDREQ_0,Enable asynchronous DMA request in stop mode for channel 0." "0: Disable asynchronous DMA request for channel 0,1: Enable asynchronous DMA request for channel 0" group.byte 0x100++0x1F line.byte 0x0 "DCHPRI3,Channel Priority" bitfld.byte 0x0 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x0 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x0 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x0 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1 "DCHPRI2,Channel Priority" bitfld.byte 0x1 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x2 "DCHPRI1,Channel Priority" bitfld.byte 0x2 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x2 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x2 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x2 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x3 "DCHPRI0,Channel Priority" bitfld.byte 0x3 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x3 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x3 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x3 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x4 "DCHPRI7,Channel Priority" bitfld.byte 0x4 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x4 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x4 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x4 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x5 "DCHPRI6,Channel Priority" bitfld.byte 0x5 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x5 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x5 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x5 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x6 "DCHPRI5,Channel Priority" bitfld.byte 0x6 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x6 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x6 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x6 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x7 "DCHPRI4,Channel Priority" bitfld.byte 0x7 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x7 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x7 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x7 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x8 "DCHPRI11,Channel Priority" bitfld.byte 0x8 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x8 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x8 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x8 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x9 "DCHPRI10,Channel Priority" bitfld.byte 0x9 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x9 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x9 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x9 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xA "DCHPRI9,Channel Priority" bitfld.byte 0xA 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xA 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xA 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xA 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xB "DCHPRI8,Channel Priority" bitfld.byte 0xB 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xB 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xB 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xB 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xC "DCHPRI15,Channel Priority" bitfld.byte 0xC 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xC 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xC 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xC 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xD "DCHPRI14,Channel Priority" bitfld.byte 0xD 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xD 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xD 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xD 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xE "DCHPRI13,Channel Priority" bitfld.byte 0xE 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xE 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xE 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xE 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xF "DCHPRI12,Channel Priority" bitfld.byte 0xF 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xF 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xF 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xF 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x10 "DCHPRI19,Channel Priority" bitfld.byte 0x10 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x10 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x10 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x10 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x11 "DCHPRI18,Channel Priority" bitfld.byte 0x11 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x11 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x11 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x11 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x12 "DCHPRI17,Channel Priority" bitfld.byte 0x12 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x12 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x12 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x12 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x13 "DCHPRI16,Channel Priority" bitfld.byte 0x13 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x13 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x13 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x13 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x14 "DCHPRI23,Channel Priority" bitfld.byte 0x14 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x14 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x14 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x14 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x15 "DCHPRI22,Channel Priority" bitfld.byte 0x15 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x15 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x15 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x15 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x16 "DCHPRI21,Channel Priority" bitfld.byte 0x16 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x16 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x16 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x16 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x17 "DCHPRI20,Channel Priority" bitfld.byte 0x17 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x17 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x17 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x17 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x18 "DCHPRI27,Channel Priority" bitfld.byte 0x18 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x18 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x18 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x18 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x19 "DCHPRI26,Channel Priority" bitfld.byte 0x19 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x19 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x19 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x19 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1A "DCHPRI25,Channel Priority" bitfld.byte 0x1A 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1A 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1A 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1A 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1B "DCHPRI24,Channel Priority" bitfld.byte 0x1B 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1B 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1B 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1B 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1C "DCHPRI31,Channel Priority" bitfld.byte 0x1C 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1C 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1C 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1C 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1D "DCHPRI30,Channel Priority" bitfld.byte 0x1D 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1D 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1D 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1D 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1E "DCHPRI29,Channel Priority" bitfld.byte 0x1E 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1E 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1E 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1E 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1F "DCHPRI28,Channel Priority" bitfld.byte 0x1F 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1F 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1F 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1F 0.--3. 1. "CHPRI,Channel n Arbitration Priority" group.long 0x1000++0x3 line.long 0x0 "TCD0_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1004++0x3 line.word 0x0 "TCD0_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD0_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0xB line.long 0x0 "TCD0_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD0_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD0_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1014++0x3 line.word 0x0 "TCD0_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD0_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1016++0x1 line.word 0x0 "TCD0_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1018++0x3 line.long 0x0 "TCD0_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x101C++0x3 line.word 0x0 "TCD0_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD0_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x101E++0x1 line.word 0x0 "TCD0_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1020++0x3 line.long 0x0 "TCD1_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1024++0x3 line.word 0x0 "TCD1_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD1_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0xB line.long 0x0 "TCD1_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD1_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD1_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1034++0x3 line.word 0x0 "TCD1_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD1_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1036++0x1 line.word 0x0 "TCD1_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1038++0x3 line.long 0x0 "TCD1_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x103C++0x3 line.word 0x0 "TCD1_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD1_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x103E++0x1 line.word 0x0 "TCD1_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1040++0x3 line.long 0x0 "TCD2_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1044++0x3 line.word 0x0 "TCD2_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD2_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0xB line.long 0x0 "TCD2_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD2_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD2_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1054++0x3 line.word 0x0 "TCD2_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD2_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1056++0x1 line.word 0x0 "TCD2_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1058++0x3 line.long 0x0 "TCD2_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x105C++0x3 line.word 0x0 "TCD2_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD2_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x105E++0x1 line.word 0x0 "TCD2_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1060++0x3 line.long 0x0 "TCD3_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1064++0x3 line.word 0x0 "TCD3_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD3_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0xB line.long 0x0 "TCD3_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD3_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD3_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1074++0x3 line.word 0x0 "TCD3_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD3_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1076++0x1 line.word 0x0 "TCD3_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1078++0x3 line.long 0x0 "TCD3_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x107C++0x3 line.word 0x0 "TCD3_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD3_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x107E++0x1 line.word 0x0 "TCD3_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1080++0x3 line.long 0x0 "TCD4_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1084++0x3 line.word 0x0 "TCD4_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD4_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0xB line.long 0x0 "TCD4_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD4_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD4_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1094++0x3 line.word 0x0 "TCD4_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD4_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1096++0x1 line.word 0x0 "TCD4_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1098++0x3 line.long 0x0 "TCD4_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x109C++0x3 line.word 0x0 "TCD4_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD4_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x109E++0x1 line.word 0x0 "TCD4_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10A0++0x3 line.long 0x0 "TCD5_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10A4++0x3 line.word 0x0 "TCD5_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD5_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0xB line.long 0x0 "TCD5_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD5_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD5_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10B4++0x3 line.word 0x0 "TCD5_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD5_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10B6++0x1 line.word 0x0 "TCD5_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10B8++0x3 line.long 0x0 "TCD5_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10BC++0x3 line.word 0x0 "TCD5_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD5_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10BE++0x1 line.word 0x0 "TCD5_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10C0++0x3 line.long 0x0 "TCD6_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10C4++0x3 line.word 0x0 "TCD6_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD6_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0xB line.long 0x0 "TCD6_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD6_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD6_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10D4++0x3 line.word 0x0 "TCD6_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD6_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10D6++0x1 line.word 0x0 "TCD6_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10D8++0x3 line.long 0x0 "TCD6_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10DC++0x3 line.word 0x0 "TCD6_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD6_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10DE++0x1 line.word 0x0 "TCD6_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10E0++0x3 line.long 0x0 "TCD7_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10E4++0x3 line.word 0x0 "TCD7_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD7_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0xB line.long 0x0 "TCD7_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD7_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD7_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10F4++0x3 line.word 0x0 "TCD7_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD7_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10F6++0x1 line.word 0x0 "TCD7_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10F8++0x3 line.long 0x0 "TCD7_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10FC++0x3 line.word 0x0 "TCD7_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD7_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10FE++0x1 line.word 0x0 "TCD7_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1100++0x3 line.long 0x0 "TCD8_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1104++0x3 line.word 0x0 "TCD8_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD8_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0xB line.long 0x0 "TCD8_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD8_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD8_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1114++0x3 line.word 0x0 "TCD8_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD8_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1116++0x1 line.word 0x0 "TCD8_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1118++0x3 line.long 0x0 "TCD8_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x111C++0x3 line.word 0x0 "TCD8_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD8_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x111E++0x1 line.word 0x0 "TCD8_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1120++0x3 line.long 0x0 "TCD9_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1124++0x3 line.word 0x0 "TCD9_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD9_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0xB line.long 0x0 "TCD9_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD9_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD9_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1134++0x3 line.word 0x0 "TCD9_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD9_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1136++0x1 line.word 0x0 "TCD9_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1138++0x3 line.long 0x0 "TCD9_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x113C++0x3 line.word 0x0 "TCD9_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD9_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x113E++0x1 line.word 0x0 "TCD9_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1140++0x3 line.long 0x0 "TCD10_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1144++0x3 line.word 0x0 "TCD10_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD10_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0xB line.long 0x0 "TCD10_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD10_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD10_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1154++0x3 line.word 0x0 "TCD10_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD10_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1156++0x1 line.word 0x0 "TCD10_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1158++0x3 line.long 0x0 "TCD10_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x115C++0x3 line.word 0x0 "TCD10_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD10_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x115E++0x1 line.word 0x0 "TCD10_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1160++0x3 line.long 0x0 "TCD11_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1164++0x3 line.word 0x0 "TCD11_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD11_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0xB line.long 0x0 "TCD11_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD11_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD11_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1174++0x3 line.word 0x0 "TCD11_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD11_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1176++0x1 line.word 0x0 "TCD11_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1178++0x3 line.long 0x0 "TCD11_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x117C++0x3 line.word 0x0 "TCD11_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD11_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x117E++0x1 line.word 0x0 "TCD11_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1180++0x3 line.long 0x0 "TCD12_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1184++0x3 line.word 0x0 "TCD12_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD12_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0xB line.long 0x0 "TCD12_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD12_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD12_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1194++0x3 line.word 0x0 "TCD12_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD12_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1196++0x1 line.word 0x0 "TCD12_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1198++0x3 line.long 0x0 "TCD12_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x119C++0x3 line.word 0x0 "TCD12_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD12_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x119E++0x1 line.word 0x0 "TCD12_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11A0++0x3 line.long 0x0 "TCD13_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11A4++0x3 line.word 0x0 "TCD13_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD13_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0xB line.long 0x0 "TCD13_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD13_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD13_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11B4++0x3 line.word 0x0 "TCD13_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD13_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11B6++0x1 line.word 0x0 "TCD13_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11B8++0x3 line.long 0x0 "TCD13_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11BC++0x3 line.word 0x0 "TCD13_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD13_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11BE++0x1 line.word 0x0 "TCD13_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11C0++0x3 line.long 0x0 "TCD14_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11C4++0x3 line.word 0x0 "TCD14_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD14_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0xB line.long 0x0 "TCD14_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD14_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD14_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11D4++0x3 line.word 0x0 "TCD14_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD14_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11D6++0x1 line.word 0x0 "TCD14_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11D8++0x3 line.long 0x0 "TCD14_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11DC++0x3 line.word 0x0 "TCD14_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD14_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11DE++0x1 line.word 0x0 "TCD14_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11E0++0x3 line.long 0x0 "TCD15_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11E4++0x3 line.word 0x0 "TCD15_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD15_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0xB line.long 0x0 "TCD15_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD15_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD15_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11F4++0x3 line.word 0x0 "TCD15_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD15_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11F6++0x1 line.word 0x0 "TCD15_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11F8++0x3 line.long 0x0 "TCD15_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11FC++0x3 line.word 0x0 "TCD15_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD15_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11FE++0x1 line.word 0x0 "TCD15_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1200++0x3 line.long 0x0 "TCD16_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1204++0x3 line.word 0x0 "TCD16_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD16_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0xB line.long 0x0 "TCD16_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD16_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD16_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1214++0x3 line.word 0x0 "TCD16_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD16_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1216++0x1 line.word 0x0 "TCD16_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1218++0x3 line.long 0x0 "TCD16_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x121C++0x3 line.word 0x0 "TCD16_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD16_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x121E++0x1 line.word 0x0 "TCD16_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1220++0x3 line.long 0x0 "TCD17_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1224++0x3 line.word 0x0 "TCD17_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD17_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0xB line.long 0x0 "TCD17_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD17_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD17_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1234++0x3 line.word 0x0 "TCD17_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD17_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1236++0x1 line.word 0x0 "TCD17_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1238++0x3 line.long 0x0 "TCD17_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x123C++0x3 line.word 0x0 "TCD17_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD17_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x123E++0x1 line.word 0x0 "TCD17_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1240++0x3 line.long 0x0 "TCD18_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1244++0x3 line.word 0x0 "TCD18_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD18_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0xB line.long 0x0 "TCD18_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD18_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD18_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1254++0x3 line.word 0x0 "TCD18_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD18_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1256++0x1 line.word 0x0 "TCD18_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1258++0x3 line.long 0x0 "TCD18_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x125C++0x3 line.word 0x0 "TCD18_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD18_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x125E++0x1 line.word 0x0 "TCD18_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1260++0x3 line.long 0x0 "TCD19_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1264++0x3 line.word 0x0 "TCD19_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD19_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0xB line.long 0x0 "TCD19_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD19_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD19_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1274++0x3 line.word 0x0 "TCD19_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD19_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1276++0x1 line.word 0x0 "TCD19_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1278++0x3 line.long 0x0 "TCD19_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x127C++0x3 line.word 0x0 "TCD19_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD19_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x127E++0x1 line.word 0x0 "TCD19_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1280++0x3 line.long 0x0 "TCD20_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1284++0x3 line.word 0x0 "TCD20_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD20_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0xB line.long 0x0 "TCD20_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD20_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD20_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1294++0x3 line.word 0x0 "TCD20_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD20_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1296++0x1 line.word 0x0 "TCD20_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1298++0x3 line.long 0x0 "TCD20_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x129C++0x3 line.word 0x0 "TCD20_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD20_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x129E++0x1 line.word 0x0 "TCD20_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12A0++0x3 line.long 0x0 "TCD21_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12A4++0x3 line.word 0x0 "TCD21_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD21_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0xB line.long 0x0 "TCD21_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD21_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD21_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12B4++0x3 line.word 0x0 "TCD21_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD21_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12B6++0x1 line.word 0x0 "TCD21_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12B8++0x3 line.long 0x0 "TCD21_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12BC++0x3 line.word 0x0 "TCD21_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD21_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12BE++0x1 line.word 0x0 "TCD21_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12C0++0x3 line.long 0x0 "TCD22_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12C4++0x3 line.word 0x0 "TCD22_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD22_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0xB line.long 0x0 "TCD22_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD22_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD22_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12D4++0x3 line.word 0x0 "TCD22_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD22_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12D6++0x1 line.word 0x0 "TCD22_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12D8++0x3 line.long 0x0 "TCD22_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12DC++0x3 line.word 0x0 "TCD22_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD22_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12DE++0x1 line.word 0x0 "TCD22_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12E0++0x3 line.long 0x0 "TCD23_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12E4++0x3 line.word 0x0 "TCD23_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD23_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0xB line.long 0x0 "TCD23_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD23_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD23_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12F4++0x3 line.word 0x0 "TCD23_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD23_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12F6++0x1 line.word 0x0 "TCD23_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12F8++0x3 line.long 0x0 "TCD23_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12FC++0x3 line.word 0x0 "TCD23_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD23_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12FE++0x1 line.word 0x0 "TCD23_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1300++0x3 line.long 0x0 "TCD24_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1304++0x3 line.word 0x0 "TCD24_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD24_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0xB line.long 0x0 "TCD24_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD24_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD24_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1314++0x3 line.word 0x0 "TCD24_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD24_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1316++0x1 line.word 0x0 "TCD24_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1318++0x3 line.long 0x0 "TCD24_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x131C++0x3 line.word 0x0 "TCD24_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD24_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x131E++0x1 line.word 0x0 "TCD24_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1320++0x3 line.long 0x0 "TCD25_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1324++0x3 line.word 0x0 "TCD25_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD25_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0xB line.long 0x0 "TCD25_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD25_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD25_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1334++0x3 line.word 0x0 "TCD25_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD25_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1336++0x1 line.word 0x0 "TCD25_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1338++0x3 line.long 0x0 "TCD25_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x133C++0x3 line.word 0x0 "TCD25_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD25_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x133E++0x1 line.word 0x0 "TCD25_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1340++0x3 line.long 0x0 "TCD26_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1344++0x3 line.word 0x0 "TCD26_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD26_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0xB line.long 0x0 "TCD26_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD26_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD26_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1354++0x3 line.word 0x0 "TCD26_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD26_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1356++0x1 line.word 0x0 "TCD26_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1358++0x3 line.long 0x0 "TCD26_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x135C++0x3 line.word 0x0 "TCD26_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD26_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x135E++0x1 line.word 0x0 "TCD26_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1360++0x3 line.long 0x0 "TCD27_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1364++0x3 line.word 0x0 "TCD27_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD27_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0xB line.long 0x0 "TCD27_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD27_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD27_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1374++0x3 line.word 0x0 "TCD27_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD27_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1376++0x1 line.word 0x0 "TCD27_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1378++0x3 line.long 0x0 "TCD27_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x137C++0x3 line.word 0x0 "TCD27_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD27_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x137E++0x1 line.word 0x0 "TCD27_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1380++0x3 line.long 0x0 "TCD28_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1384++0x3 line.word 0x0 "TCD28_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD28_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0xB line.long 0x0 "TCD28_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD28_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD28_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1394++0x3 line.word 0x0 "TCD28_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD28_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1396++0x1 line.word 0x0 "TCD28_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1398++0x3 line.long 0x0 "TCD28_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x139C++0x3 line.word 0x0 "TCD28_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD28_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x139E++0x1 line.word 0x0 "TCD28_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13A0++0x3 line.long 0x0 "TCD29_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13A4++0x3 line.word 0x0 "TCD29_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD29_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0xB line.long 0x0 "TCD29_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD29_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD29_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13B4++0x3 line.word 0x0 "TCD29_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD29_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13B6++0x1 line.word 0x0 "TCD29_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13B8++0x3 line.long 0x0 "TCD29_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13BC++0x3 line.word 0x0 "TCD29_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD29_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13BE++0x1 line.word 0x0 "TCD29_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13C0++0x3 line.long 0x0 "TCD30_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13C4++0x3 line.word 0x0 "TCD30_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD30_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0xB line.long 0x0 "TCD30_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD30_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD30_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13D4++0x3 line.word 0x0 "TCD30_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD30_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13D6++0x1 line.word 0x0 "TCD30_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13D8++0x3 line.long 0x0 "TCD30_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13DC++0x3 line.word 0x0 "TCD30_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD30_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13DE++0x1 line.word 0x0 "TCD30_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13E0++0x3 line.long 0x0 "TCD31_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13E4++0x3 line.word 0x0 "TCD31_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD31_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0xB line.long 0x0 "TCD31_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD31_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD31_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13F4++0x3 line.word 0x0 "TCD31_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD31_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13F6++0x1 line.word 0x0 "TCD31_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13F8++0x3 line.long 0x0 "TCD31_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13FC++0x3 line.word 0x0 "TCD31_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD31_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13FE++0x1 line.word 0x0 "TCD31_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" tree.end endif sif (cpuis("IMXRT1166-CM4")) tree "DMA1" base ad:0x40C14000 group.long 0x0++0x3 line.long 0x0 "CR,Control" rbitfld.long 0x0 31. "ACTIVE,eDMA Active Status" "0: eDMA is idle,1: eDMA is executing a channel" hexmask.long.byte 0x0 24.--30. 1. "VERSION,eDMA version number" newline bitfld.long 0x0 17. "CX,Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" bitfld.long 0x0 16. "ECX,Error Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" newline bitfld.long 0x0 10. "GRP1PRI,Channel Group 1 Priority" "0,1" bitfld.long 0x0 8. "GRP0PRI,Channel Group 0 Priority" "0,1" newline bitfld.long 0x0 7. "EMLM,Enable Minor Loop Mapping" "0: Disabled,1: Enabled" bitfld.long 0x0 6. "CLM,Continuous Link Mode" "0: Continuous link mode is off,1: Continuous link mode is on" newline bitfld.long 0x0 5. "HALT,Halt eDMA Operations" "0: Normal operation,1: eDMA operations halted" bitfld.long 0x0 4. "HOE,Halt On Error" "0: Normal operation,1: Error causes HALT field to be automatically set.." newline bitfld.long 0x0 3. "ERGA,Enable Round Robin Group Arbitration" "0: Fixed priority arbitration,1: Round robin arbitration" bitfld.long 0x0 2. "ERCA,Enable Round Robin Channel Arbitration" "0: Fixed priority arbitration within each group,1: Round robin arbitration within each group" newline bitfld.long 0x0 1. "EDBG,Enable Debug" "0: When the chip is in Debug mode the eDMA..,1: When the chip is in debug mode the DMA stalls.." rgroup.long 0x4++0x3 line.long 0x0 "ES,Error Status" bitfld.long 0x0 31. "VLD,Logical OR of all ERR status fields" "0: No ERR fields are 1,1: At least one ERR field has a value of 1.." bitfld.long 0x0 16. "ECX,Transfer Canceled" "0: No canceled transfers,1: The most-recently recorded entry was a canceled.." newline bitfld.long 0x0 15. "GPE,Group Priority Error" "0: No group priority error.,1: The most-recently recorded error was a.." bitfld.long 0x0 14. "CPE,Channel Priority Error" "0: No channel priority error.,1: The most-recently recorded error was a.." newline hexmask.long.byte 0x0 8.--12. 1. "ERRCHN,Error Channel Number or Canceled Channel Number" bitfld.long 0x0 7. "SAE,Source Address Error" "0: No source address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 6. "SOE,Source Offset Error" "0: No source offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 5. "DAE,Destination Address Error" "0: No destination address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 4. "DOE,Destination Offset Error" "0: No destination offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 3. "NCE,NBYTES/CITER Configuration Error" "0: No NBYTES/CITER configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 2. "SGE,Scatter/Gather Configuration Error" "0: No scatter/gather configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 1. "SBE,Source Bus Error" "0: No source bus error.,1: The most-recently recorded error was a bus error.." newline bitfld.long 0x0 0. "DBE,Destination Bus Error" "0: No destination bus error.,1: The most-recently recorded error was a bus error.." group.long 0xC++0x3 line.long 0x0 "ERQ,Enable Request" bitfld.long 0x0 31. "ERQ31,Enable DMA Request 31" "0: The DMA request signal for channel 31 is disabled,1: The DMA request signal for channel 31 is enabled" bitfld.long 0x0 30. "ERQ30,Enable DMA Request 30" "0: The DMA request signal for channel 30 is disabled,1: The DMA request signal for channel 30 is enabled" newline bitfld.long 0x0 29. "ERQ29,Enable DMA Request 29" "0: The DMA request signal for channel 29 is disabled,1: The DMA request signal for channel 29 is enabled" bitfld.long 0x0 28. "ERQ28,Enable DMA Request 28" "0: The DMA request signal for channel 28 is disabled,1: The DMA request signal for channel 28 is enabled" newline bitfld.long 0x0 27. "ERQ27,Enable DMA Request 27" "0: The DMA request signal for channel 27 is disabled,1: The DMA request signal for channel 27 is enabled" bitfld.long 0x0 26. "ERQ26,Enable DMA Request 26" "0: The DMA request signal for channel 26 is disabled,1: The DMA request signal for channel 26 is enabled" newline bitfld.long 0x0 25. "ERQ25,Enable DMA Request 25" "0: The DMA request signal for channel 25 is disabled,1: The DMA request signal for channel 25 is enabled" bitfld.long 0x0 24. "ERQ24,Enable DMA Request 24" "0: The DMA request signal for channel 24 is disabled,1: The DMA request signal for channel 24 is enabled" newline bitfld.long 0x0 23. "ERQ23,Enable DMA Request 23" "0: The DMA request signal for channel 23 is disabled,1: The DMA request signal for channel 23 is enabled" bitfld.long 0x0 22. "ERQ22,Enable DMA Request 22" "0: The DMA request signal for channel 22 is disabled,1: The DMA request signal for channel 22 is enabled" newline bitfld.long 0x0 21. "ERQ21,Enable DMA Request 21" "0: The DMA request signal for channel 21 is disabled,1: The DMA request signal for channel 21 is enabled" bitfld.long 0x0 20. "ERQ20,Enable DMA Request 20" "0: The DMA request signal for channel 20 is disabled,1: The DMA request signal for channel 20 is enabled" newline bitfld.long 0x0 19. "ERQ19,Enable DMA Request 19" "0: The DMA request signal for channel 19 is disabled,1: The DMA request signal for channel 19 is enabled" bitfld.long 0x0 18. "ERQ18,Enable DMA Request 18" "0: The DMA request signal for channel 18 is disabled,1: The DMA request signal for channel 18 is enabled" newline bitfld.long 0x0 17. "ERQ17,Enable DMA Request 17" "0: The DMA request signal for channel 17 is disabled,1: The DMA request signal for channel 17 is enabled" bitfld.long 0x0 16. "ERQ16,Enable DMA Request 16" "0: The DMA request signal for channel 16 is disabled,1: The DMA request signal for channel 16 is enabled" newline bitfld.long 0x0 15. "ERQ15,Enable DMA Request 15" "0: The DMA request signal for channel 15 is disabled,1: The DMA request signal for channel 15 is enabled" bitfld.long 0x0 14. "ERQ14,Enable DMA Request 14" "0: The DMA request signal for channel 14 is disabled,1: The DMA request signal for channel 14 is enabled" newline bitfld.long 0x0 13. "ERQ13,Enable DMA Request 13" "0: The DMA request signal for channel 13 is disabled,1: The DMA request signal for channel 13 is enabled" bitfld.long 0x0 12. "ERQ12,Enable DMA Request 12" "0: The DMA request signal for channel 12 is disabled,1: The DMA request signal for channel 12 is enabled" newline bitfld.long 0x0 11. "ERQ11,Enable DMA Request 11" "0: The DMA request signal for channel 11 is disabled,1: The DMA request signal for channel 11 is enabled" bitfld.long 0x0 10. "ERQ10,Enable DMA Request 10" "0: The DMA request signal for channel 10 is disabled,1: The DMA request signal for channel 10 is enabled" newline bitfld.long 0x0 9. "ERQ9,Enable DMA Request 9" "0: The DMA request signal for channel 9 is disabled,1: The DMA request signal for channel 9 is enabled" bitfld.long 0x0 8. "ERQ8,Enable DMA Request 8" "0: The DMA request signal for channel 8 is disabled,1: The DMA request signal for channel 8 is enabled" newline bitfld.long 0x0 7. "ERQ7,Enable DMA Request 7" "0: The DMA request signal for channel 7 is disabled,1: The DMA request signal for channel 7 is enabled" bitfld.long 0x0 6. "ERQ6,Enable DMA Request 6" "0: The DMA request signal for channel 6 is disabled,1: The DMA request signal for channel 6 is enabled" newline bitfld.long 0x0 5. "ERQ5,Enable DMA Request 5" "0: The DMA request signal for channel 5 is disabled,1: The DMA request signal for channel 5 is enabled" bitfld.long 0x0 4. "ERQ4,Enable DMA Request 4" "0: The DMA request signal for channel 4 is disabled,1: The DMA request signal for channel 4 is enabled" newline bitfld.long 0x0 3. "ERQ3,Enable DMA Request 3" "0: The DMA request signal for channel 3 is disabled,1: The DMA request signal for channel 3 is enabled" bitfld.long 0x0 2. "ERQ2,Enable DMA Request 2" "0: The DMA request signal for channel 2 is disabled,1: The DMA request signal for channel 2 is enabled" newline bitfld.long 0x0 1. "ERQ1,Enable DMA Request 1" "0: The DMA request signal for channel 1 is disabled,1: The DMA request signal for channel 1 is enabled" bitfld.long 0x0 0. "ERQ0,Enable DMA Request 0" "0: The DMA request signal for channel 0 is disabled,1: The DMA request signal for channel 0 is enabled" group.long 0x14++0x3 line.long 0x0 "EEI,Enable Error Interrupt" bitfld.long 0x0 31. "EEI31,Enable Error Interrupt 31" "0: An error on channel 31 does not generate an..,1: An error on channel 31 generates an error.." bitfld.long 0x0 30. "EEI30,Enable Error Interrupt 30" "0: An error on channel 30 does not generate an..,1: An error on channel 30 generates an error.." newline bitfld.long 0x0 29. "EEI29,Enable Error Interrupt 29" "0: An error on channel 29 does not generate an..,1: An error on channel 29 generates an error.." bitfld.long 0x0 28. "EEI28,Enable Error Interrupt 28" "0: An error on channel 28 does not generate an..,1: An error on channel 28 generates an error.." newline bitfld.long 0x0 27. "EEI27,Enable Error Interrupt 27" "0: An error on channel 27 does not generate an..,1: An error on channel 27 generates an error.." bitfld.long 0x0 26. "EEI26,Enable Error Interrupt 26" "0: An error on channel 26 does not generate an..,1: An error on channel 26 generates an error.." newline bitfld.long 0x0 25. "EEI25,Enable Error Interrupt 25" "0: An error on channel 25 does not generate an..,1: An error on channel 25 generates an error.." bitfld.long 0x0 24. "EEI24,Enable Error Interrupt 24" "0: An error on channel 24 does not generate an..,1: An error on channel 24 generates an error.." newline bitfld.long 0x0 23. "EEI23,Enable Error Interrupt 23" "0: An error on channel 23 does not generate an..,1: An error on channel 23 generates an error.." bitfld.long 0x0 22. "EEI22,Enable Error Interrupt 22" "0: An error on channel 22 does not generate an..,1: An error on channel 22 generates an error.." newline bitfld.long 0x0 21. "EEI21,Enable Error Interrupt 21" "0: An error on channel 21 does not generate an..,1: An error on channel 21 generates an error.." bitfld.long 0x0 20. "EEI20,Enable Error Interrupt 20" "0: An error on channel 20 does not generate an..,1: An error on channel 20 generates an error.." newline bitfld.long 0x0 19. "EEI19,Enable Error Interrupt 19" "0: An error on channel 19 does not generate an..,1: An error on channel 19 generates an error.." bitfld.long 0x0 18. "EEI18,Enable Error Interrupt 18" "0: An error on channel 18 does not generate an..,1: An error on channel 18 generates an error.." newline bitfld.long 0x0 17. "EEI17,Enable Error Interrupt 17" "0: An error on channel 17 does not generate an..,1: An error on channel 17 generates an error.." bitfld.long 0x0 16. "EEI16,Enable Error Interrupt 16" "0: An error on channel 16 does not generate an..,1: An error on channel 16 generates an error.." newline bitfld.long 0x0 15. "EEI15,Enable Error Interrupt 15" "0: An error on channel 15 does not generate an..,1: An error on channel 15 generates an error.." bitfld.long 0x0 14. "EEI14,Enable Error Interrupt 14" "0: An error on channel 14 does not generate an..,1: An error on channel 14 generates an error.." newline bitfld.long 0x0 13. "EEI13,Enable Error Interrupt 13" "0: An error on channel 13 does not generate an..,1: An error on channel 13 generates an error.." bitfld.long 0x0 12. "EEI12,Enable Error Interrupt 12" "0: An error on channel 12 does not generate an..,1: An error on channel 12 generates an error.." newline bitfld.long 0x0 11. "EEI11,Enable Error Interrupt 11" "0: An error on channel 11 does not generate an..,1: An error on channel 11 generates an error.." bitfld.long 0x0 10. "EEI10,Enable Error Interrupt 10" "0: An error on channel 10 does not generate an..,1: An error on channel 10 generates an error.." newline bitfld.long 0x0 9. "EEI9,Enable Error Interrupt 9" "0: An error on channel 9 does not generate an error..,1: An error on channel 9 generates an error.." bitfld.long 0x0 8. "EEI8,Enable Error Interrupt 8" "0: An error on channel 8 does not generate an error..,1: An error on channel 8 generates an error.." newline bitfld.long 0x0 7. "EEI7,Enable Error Interrupt 7" "0: An error on channel 7 does not generate an error..,1: An error on channel 7 generates an error.." bitfld.long 0x0 6. "EEI6,Enable Error Interrupt 6" "0: An error on channel 6 does not generate an error..,1: An error on channel 6 generates an error.." newline bitfld.long 0x0 5. "EEI5,Enable Error Interrupt 5" "0: An error on channel 5 does not generate an error..,1: An error on channel 5 generates an error.." bitfld.long 0x0 4. "EEI4,Enable Error Interrupt 4" "0: An error on channel 4 does not generate an error..,1: An error on channel 4 generates an error.." newline bitfld.long 0x0 3. "EEI3,Enable Error Interrupt 3" "0: An error on channel 3 does not generate an error..,1: An error on channel 3 generates an error.." bitfld.long 0x0 2. "EEI2,Enable Error Interrupt 2" "0: An error on channel 2 does not generate an error..,1: An error on channel 2 generates an error.." newline bitfld.long 0x0 1. "EEI1,Enable Error Interrupt 1" "0: An error on channel 1 does not generate an error..,1: An error on channel 1 generates an error.." bitfld.long 0x0 0. "EEI0,Enable Error Interrupt 0" "0: An error on channel 0 does not generate an error..,1: An error on channel 0 generates an error.." group.byte 0x18++0x7 line.byte 0x0 "CEEI,Clear Enable Error Interrupt" bitfld.byte 0x0 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x0 6. "CAEE,Clear All Enable Error Interrupts" "0: Write 0 only to the EEI field specified in the..,1: Write 0 to all fields in EEI" newline hexmask.byte 0x0 0.--4. 1. "CEEI,Clear Enable Error Interrupt" line.byte 0x1 "SEEI,Set Enable Error Interrupt" bitfld.byte 0x1 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x1 6. "SAEE,Set All Enable Error Interrupts" "0: Write 1 only to the EEI field specified in the..,1: Writes 1 to all fields in EEI" newline hexmask.byte 0x1 0.--4. 1. "SEEI,Set Enable Error Interrupt" line.byte 0x2 "CERQ,Clear Enable Request" bitfld.byte 0x2 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x2 6. "CAER,Clear All Enable Requests" "0: Write 0 to only the ERQ field specified in the..,1: Write 0 to all fields in ERQ" newline hexmask.byte 0x2 0.--4. 1. "CERQ,Clear Enable Request" line.byte 0x3 "SERQ,Set Enable Request" bitfld.byte 0x3 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x3 6. "SAER,Set All Enable Requests" "0: Write 1 to only the ERQ field specified in the..,1: Write 1 to all fields in ERQ" newline hexmask.byte 0x3 0.--4. 1. "SERQ,Set Enable Request" line.byte 0x4 "CDNE,Clear DONE Status Bit" bitfld.byte 0x4 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x4 6. "CADN,Clears All DONE fields" "0: Writes 0 to only the TCDn_CSR[DONE] field..,1: Writes 0 to all bits in TCDn_CSR[DONE]" newline hexmask.byte 0x4 0.--4. 1. "CDNE,Clear DONE field" line.byte 0x5 "SSRT,Set START Bit" bitfld.byte 0x5 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x5 6. "SAST,Set All START fields (activates all channels)" "0: Write 1 to only the TCDn_CSR[START] field..,1: Write 1 to all bits in TCDn_CSR[START]" newline hexmask.byte 0x5 0.--4. 1. "SSRT,Set START field" line.byte 0x6 "CERR,Clear Error" bitfld.byte 0x6 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x6 6. "CAEI,Clear All Error Indicators" "0: Write 0 to only the ERR field specified in the..,1: Write 0 to all fields in ERR" newline hexmask.byte 0x6 0.--4. 1. "CERR,Clear Error Indicator" line.byte 0x7 "CINT,Clear Interrupt Request" bitfld.byte 0x7 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x7 6. "CAIR,Clear All Interrupt Requests" "0: Clear only the INT field specified in the CINT..,1: Clear all bits in INT" newline hexmask.byte 0x7 0.--4. 1. "CINT,Clear Interrupt Request" group.long 0x24++0x3 line.long 0x0 "INT,Interrupt Request" eventfld.long 0x0 31. "INT31,Interrupt Request 31" "0: The interrupt request for channel 31 is cleared,1: The interrupt request for channel 31 is active" eventfld.long 0x0 30. "INT30,Interrupt Request 30" "0: The interrupt request for channel 30 is cleared,1: The interrupt request for channel 30 is active" newline eventfld.long 0x0 29. "INT29,Interrupt Request 29" "0: The interrupt request for channel 29 is cleared,1: The interrupt request for channel 29 is active" eventfld.long 0x0 28. "INT28,Interrupt Request 28" "0: The interrupt request for channel 28 is cleared,1: The interrupt request for channel 28 is active" newline eventfld.long 0x0 27. "INT27,Interrupt Request 27" "0: The interrupt request for channel 27 is cleared,1: The interrupt request for channel 27 is active" eventfld.long 0x0 26. "INT26,Interrupt Request 26" "0: The interrupt request for channel 26 is cleared,1: The interrupt request for channel 26 is active" newline eventfld.long 0x0 25. "INT25,Interrupt Request 25" "0: The interrupt request for channel 25 is cleared,1: The interrupt request for channel 25 is active" eventfld.long 0x0 24. "INT24,Interrupt Request 24" "0: The interrupt request for channel 24 is cleared,1: The interrupt request for channel 24 is active" newline eventfld.long 0x0 23. "INT23,Interrupt Request 23" "0: The interrupt request for channel 23 is cleared,1: The interrupt request for channel 23 is active" eventfld.long 0x0 22. "INT22,Interrupt Request 22" "0: The interrupt request for channel 22 is cleared,1: The interrupt request for channel 22 is active" newline eventfld.long 0x0 21. "INT21,Interrupt Request 21" "0: The interrupt request for channel 21 is cleared,1: The interrupt request for channel 21 is active" eventfld.long 0x0 20. "INT20,Interrupt Request 20" "0: The interrupt request for channel 20 is cleared,1: The interrupt request for channel 20 is active" newline eventfld.long 0x0 19. "INT19,Interrupt Request 19" "0: The interrupt request for channel 19 is cleared,1: The interrupt request for channel 19 is active" eventfld.long 0x0 18. "INT18,Interrupt Request 18" "0: The interrupt request for channel 18 is cleared,1: The interrupt request for channel 18 is active" newline eventfld.long 0x0 17. "INT17,Interrupt Request 17" "0: The interrupt request for channel 17 is cleared,1: The interrupt request for channel 17 is active" eventfld.long 0x0 16. "INT16,Interrupt Request 16" "0: The interrupt request for channel 16 is cleared,1: The interrupt request for channel 16 is active" newline eventfld.long 0x0 15. "INT15,Interrupt Request 15" "0: The interrupt request for channel 15 is cleared,1: The interrupt request for channel 15 is active" eventfld.long 0x0 14. "INT14,Interrupt Request 14" "0: The interrupt request for channel 14 is cleared,1: The interrupt request for channel 14 is active" newline eventfld.long 0x0 13. "INT13,Interrupt Request 13" "0: The interrupt request for channel 13 is cleared,1: The interrupt request for channel 13 is active" eventfld.long 0x0 12. "INT12,Interrupt Request 12" "0: The interrupt request for channel 12 is cleared,1: The interrupt request for channel 12 is active" newline eventfld.long 0x0 11. "INT11,Interrupt Request 11" "0: The interrupt request for channel 11 is cleared,1: The interrupt request for channel 11 is active" eventfld.long 0x0 10. "INT10,Interrupt Request 10" "0: The interrupt request for channel 10 is cleared,1: The interrupt request for channel 10 is active" newline eventfld.long 0x0 9. "INT9,Interrupt Request 9" "0: The interrupt request for channel 9 is cleared,1: The interrupt request for channel 9 is active" eventfld.long 0x0 8. "INT8,Interrupt Request 8" "0: The interrupt request for channel 8 is cleared,1: The interrupt request for channel 8 is active" newline eventfld.long 0x0 7. "INT7,Interrupt Request 7" "0: The interrupt request for channel 7 is cleared,1: The interrupt request for channel 7 is active" eventfld.long 0x0 6. "INT6,Interrupt Request 6" "0: The interrupt request for channel 6 is cleared,1: The interrupt request for channel 6 is active" newline eventfld.long 0x0 5. "INT5,Interrupt Request 5" "0: The interrupt request for channel 5 is cleared,1: The interrupt request for channel 5 is active" eventfld.long 0x0 4. "INT4,Interrupt Request 4" "0: The interrupt request for channel 4 is cleared,1: The interrupt request for channel 4 is active" newline eventfld.long 0x0 3. "INT3,Interrupt Request 3" "0: The interrupt request for channel 3 is cleared,1: The interrupt request for channel 3 is active" eventfld.long 0x0 2. "INT2,Interrupt Request 2" "0: The interrupt request for channel 2 is cleared,1: The interrupt request for channel 2 is active" newline eventfld.long 0x0 1. "INT1,Interrupt Request 1" "0: The interrupt request for channel 1 is cleared,1: The interrupt request for channel 1 is active" eventfld.long 0x0 0. "INT0,Interrupt Request 0" "0: The interrupt request for channel 0 is cleared,1: The interrupt request for channel 0 is active" group.long 0x2C++0x3 line.long 0x0 "ERR,Error" eventfld.long 0x0 31. "ERR31,Error In Channel 31" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 30. "ERR30,Error In Channel 30" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 29. "ERR29,Error In Channel 29" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 28. "ERR28,Error In Channel 28" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 27. "ERR27,Error In Channel 27" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 26. "ERR26,Error In Channel 26" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 25. "ERR25,Error In Channel 25" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 24. "ERR24,Error In Channel 24" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 23. "ERR23,Error In Channel 23" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 22. "ERR22,Error In Channel 22" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 21. "ERR21,Error In Channel 21" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 20. "ERR20,Error In Channel 20" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 19. "ERR19,Error In Channel 19" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 18. "ERR18,Error In Channel 18" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 17. "ERR17,Error In Channel 17" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 16. "ERR16,Error In Channel 16" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 15. "ERR15,Error In Channel 15" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 14. "ERR14,Error In Channel 14" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 13. "ERR13,Error In Channel 13" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 12. "ERR12,Error In Channel 12" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 11. "ERR11,Error In Channel 11" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 10. "ERR10,Error In Channel 10" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 9. "ERR9,Error In Channel 9" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 8. "ERR8,Error In Channel 8" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 7. "ERR7,Error In Channel 7" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 6. "ERR6,Error In Channel 6" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 5. "ERR5,Error In Channel 5" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 4. "ERR4,Error In Channel 4" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 3. "ERR3,Error In Channel 3" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 2. "ERR2,Error In Channel 2" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 1. "ERR1,Error In Channel 1" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 0. "ERR0,Error In Channel 0" "0: No error in this channel has occurred,1: An error in this channel has occurred" rgroup.long 0x34++0x3 line.long 0x0 "HRS,Hardware Request Status" bitfld.long 0x0 31. "HRS31,Hardware Request Status Channel 31" "0: A hardware service request for channel 31 is not..,1: A hardware service request for channel 31 is.." bitfld.long 0x0 30. "HRS30,Hardware Request Status Channel 30" "0: A hardware service request for channel 30 is not..,1: A hardware service request for channel 30 is.." newline bitfld.long 0x0 29. "HRS29,Hardware Request Status Channel 29" "0: A hardware service request for channel 29 is not..,1: A hardware service request for channel 29 is.." bitfld.long 0x0 28. "HRS28,Hardware Request Status Channel 28" "0: A hardware service request for channel 28 is not..,1: A hardware service request for channel 28 is.." newline bitfld.long 0x0 27. "HRS27,Hardware Request Status Channel 27" "0: A hardware service request for channel 27 is not..,1: A hardware service request for channel 27 is.." bitfld.long 0x0 26. "HRS26,Hardware Request Status Channel 26" "0: A hardware service request for channel 26 is not..,1: A hardware service request for channel 26 is.." newline bitfld.long 0x0 25. "HRS25,Hardware Request Status Channel 25" "0: A hardware service request for channel 25 is not..,1: A hardware service request for channel 25 is.." bitfld.long 0x0 24. "HRS24,Hardware Request Status Channel 24" "0: A hardware service request for channel 24 is not..,1: A hardware service request for channel 24 is.." newline bitfld.long 0x0 23. "HRS23,Hardware Request Status Channel 23" "0: A hardware service request for channel 23 is not..,1: A hardware service request for channel 23 is.." bitfld.long 0x0 22. "HRS22,Hardware Request Status Channel 22" "0: A hardware service request for channel 22 is not..,1: A hardware service request for channel 22 is.." newline bitfld.long 0x0 21. "HRS21,Hardware Request Status Channel 21" "0: A hardware service request for channel 21 is not..,1: A hardware service request for channel 21 is.." bitfld.long 0x0 20. "HRS20,Hardware Request Status Channel 20" "0: A hardware service request for channel 20 is not..,1: A hardware service request for channel 20 is.." newline bitfld.long 0x0 19. "HRS19,Hardware Request Status Channel 19" "0: A hardware service request for channel 19 is not..,1: A hardware service request for channel 19 is.." bitfld.long 0x0 18. "HRS18,Hardware Request Status Channel 18" "0: A hardware service request for channel 18 is not..,1: A hardware service request for channel 18 is.." newline bitfld.long 0x0 17. "HRS17,Hardware Request Status Channel 17" "0: A hardware service request for channel 17 is not..,1: A hardware service request for channel 17 is.." bitfld.long 0x0 16. "HRS16,Hardware Request Status Channel 16" "0: A hardware service request for channel 16 is not..,1: A hardware service request for channel 16 is.." newline bitfld.long 0x0 15. "HRS15,Hardware Request Status Channel 15" "0: A hardware service request for channel 15 is not..,1: A hardware service request for channel 15 is.." bitfld.long 0x0 14. "HRS14,Hardware Request Status Channel 14" "0: A hardware service request for channel 14 is not..,1: A hardware service request for channel 14 is.." newline bitfld.long 0x0 13. "HRS13,Hardware Request Status Channel 13" "0: A hardware service request for channel 13 is not..,1: A hardware service request for channel 13 is.." bitfld.long 0x0 12. "HRS12,Hardware Request Status Channel 12" "0: A hardware service request for channel 12 is not..,1: A hardware service request for channel 12 is.." newline bitfld.long 0x0 11. "HRS11,Hardware Request Status Channel 11" "0: A hardware service request for channel 11 is not..,1: A hardware service request for channel 11 is.." bitfld.long 0x0 10. "HRS10,Hardware Request Status Channel 10" "0: A hardware service request for channel 10 is not..,1: A hardware service request for channel 10 is.." newline bitfld.long 0x0 9. "HRS9,Hardware Request Status Channel 9" "0: A hardware service request for channel 9 is not..,1: A hardware service request for channel 9 is.." bitfld.long 0x0 8. "HRS8,Hardware Request Status Channel 8" "0: A hardware service request for channel 8 is not..,1: A hardware service request for channel 8 is.." newline bitfld.long 0x0 7. "HRS7,Hardware Request Status Channel 7" "0: A hardware service request for channel 7 is not..,1: A hardware service request for channel 7 is.." bitfld.long 0x0 6. "HRS6,Hardware Request Status Channel 6" "0: A hardware service request for channel 6 is not..,1: A hardware service request for channel 6 is.." newline bitfld.long 0x0 5. "HRS5,Hardware Request Status Channel 5" "0: A hardware service request for channel 5 is not..,1: A hardware service request for channel 5 is.." bitfld.long 0x0 4. "HRS4,Hardware Request Status Channel 4" "0: A hardware service request for channel 4 is not..,1: A hardware service request for channel 4 is.." newline bitfld.long 0x0 3. "HRS3,Hardware Request Status Channel 3" "0: A hardware service request for channel 3 is not..,1: A hardware service request for channel 3 is.." bitfld.long 0x0 2. "HRS2,Hardware Request Status Channel 2" "0: A hardware service request for channel 2 is not..,1: A hardware service request for channel 2 is.." newline bitfld.long 0x0 1. "HRS1,Hardware Request Status Channel 1" "0: A hardware service request for channel 1 is not..,1: A hardware service request for channel 1 is.." bitfld.long 0x0 0. "HRS0,Hardware Request Status Channel 0" "0: A hardware service request for channel 0 is not..,1: A hardware service request for channel 0 is.." group.long 0x44++0x3 line.long 0x0 "EARS,Enable Asynchronous Request in Stop" bitfld.long 0x0 31. "EDREQ_31,Enable asynchronous DMA request in stop mode for channel 31." "0: Disable asynchronous DMA request for channel 31,1: Enable asynchronous DMA request for channel 31" bitfld.long 0x0 30. "EDREQ_30,Enable asynchronous DMA request in stop mode for channel 30." "0: Disable asynchronous DMA request for channel 30,1: Enable asynchronous DMA request for channel 30" newline bitfld.long 0x0 29. "EDREQ_29,Enable asynchronous DMA request in stop mode for channel 29." "0: Disable asynchronous DMA request for channel 29,1: Enable asynchronous DMA request for channel 29" bitfld.long 0x0 28. "EDREQ_28,Enable asynchronous DMA request in stop mode for channel 28." "0: Disable asynchronous DMA request for channel 28,1: Enable asynchronous DMA request for channel 28" newline bitfld.long 0x0 27. "EDREQ_27,Enable asynchronous DMA request in stop mode for channel 27." "0: Disable asynchronous DMA request for channel 27,1: Enable asynchronous DMA request for channel 27" bitfld.long 0x0 26. "EDREQ_26,Enable asynchronous DMA request in stop mode for channel 26." "0: Disable asynchronous DMA request for channel 26,1: Enable asynchronous DMA request for channel 26" newline bitfld.long 0x0 25. "EDREQ_25,Enable asynchronous DMA request in stop mode for channel 25." "0: Disable asynchronous DMA request for channel 25,1: Enable asynchronous DMA request for channel 25" bitfld.long 0x0 24. "EDREQ_24,Enable asynchronous DMA request in stop mode for channel 24." "0: Disable asynchronous DMA request for channel 24,1: Enable asynchronous DMA request for channel 24" newline bitfld.long 0x0 23. "EDREQ_23,Enable asynchronous DMA request in stop mode for channel 23." "0: Disable asynchronous DMA request for channel 23,1: Enable asynchronous DMA request for channel 23" bitfld.long 0x0 22. "EDREQ_22,Enable asynchronous DMA request in stop mode for channel 22." "0: Disable asynchronous DMA request for channel 22,1: Enable asynchronous DMA request for channel 22" newline bitfld.long 0x0 21. "EDREQ_21,Enable asynchronous DMA request in stop mode for channel 21." "0: Disable asynchronous DMA request for channel 21,1: Enable asynchronous DMA request for channel 21" bitfld.long 0x0 20. "EDREQ_20,Enable asynchronous DMA request in stop mode for channel 20." "0: Disable asynchronous DMA request for channel 20,1: Enable asynchronous DMA request for channel 20" newline bitfld.long 0x0 19. "EDREQ_19,Enable asynchronous DMA request in stop mode for channel 19." "0: Disable asynchronous DMA request for channel 19,1: Enable asynchronous DMA request for channel 19" bitfld.long 0x0 18. "EDREQ_18,Enable asynchronous DMA request in stop mode for channel 18." "0: Disable asynchronous DMA request for channel 18,1: Enable asynchronous DMA request for channel 18" newline bitfld.long 0x0 17. "EDREQ_17,Enable asynchronous DMA request in stop mode for channel 17." "0: Disable asynchronous DMA request for channel 17,1: Enable asynchronous DMA request for channel 17" bitfld.long 0x0 16. "EDREQ_16,Enable asynchronous DMA request in stop mode for channel 16." "0: Disable asynchronous DMA request for channel 16,1: Enable asynchronous DMA request for channel 16" newline bitfld.long 0x0 15. "EDREQ_15,Enable asynchronous DMA request in stop mode for channel 15." "0: Disable asynchronous DMA request for channel 15,1: Enable asynchronous DMA request for channel 15" bitfld.long 0x0 14. "EDREQ_14,Enable asynchronous DMA request in stop mode for channel 14." "0: Disable asynchronous DMA request for channel 14,1: Enable asynchronous DMA request for channel 14" newline bitfld.long 0x0 13. "EDREQ_13,Enable asynchronous DMA request in stop mode for channel 13." "0: Disable asynchronous DMA request for channel 13,1: Enable asynchronous DMA request for channel 13" bitfld.long 0x0 12. "EDREQ_12,Enable asynchronous DMA request in stop mode for channel 12." "0: Disable asynchronous DMA request for channel 12,1: Enable asynchronous DMA request for channel 12" newline bitfld.long 0x0 11. "EDREQ_11,Enable asynchronous DMA request in stop mode for channel 11." "0: Disable asynchronous DMA request for channel 11,1: Enable asynchronous DMA request for channel 11" bitfld.long 0x0 10. "EDREQ_10,Enable asynchronous DMA request in stop mode for channel 10." "0: Disable asynchronous DMA request for channel 10,1: Enable asynchronous DMA request for channel 10" newline bitfld.long 0x0 9. "EDREQ_9,Enable asynchronous DMA request in stop mode for channel 9." "0: Disable asynchronous DMA request for channel 9,1: Enable asynchronous DMA request for channel 9" bitfld.long 0x0 8. "EDREQ_8,Enable asynchronous DMA request in stop mode for channel 8." "0: Disable asynchronous DMA request for channel 8,1: Enable asynchronous DMA request for channel 8" newline bitfld.long 0x0 7. "EDREQ_7,Enable asynchronous DMA request in stop mode for channel 7." "0: Disable asynchronous DMA request for channel 7,1: Enable asynchronous DMA request for channel 7" bitfld.long 0x0 6. "EDREQ_6,Enable asynchronous DMA request in stop mode for channel 6." "0: Disable asynchronous DMA request for channel 6,1: Enable asynchronous DMA request for channel 6" newline bitfld.long 0x0 5. "EDREQ_5,Enable asynchronous DMA request in stop mode for channel 5." "0: Disable asynchronous DMA request for channel 5,1: Enable asynchronous DMA request for channel 5" bitfld.long 0x0 4. "EDREQ_4,Enable asynchronous DMA request in stop mode for channel 4." "0: Disable asynchronous DMA request for channel 4,1: Enable asynchronous DMA request for channel 4" newline bitfld.long 0x0 3. "EDREQ_3,Enable asynchronous DMA request in stop mode for channel 3." "0: Disable asynchronous DMA request for channel 3,1: Enable asynchronous DMA request for channel 3" bitfld.long 0x0 2. "EDREQ_2,Enable asynchronous DMA request in stop mode for channel 2." "0: Disable asynchronous DMA request for channel 2,1: Enable asynchronous DMA request for channel 2" newline bitfld.long 0x0 1. "EDREQ_1,Enable asynchronous DMA request in stop mode for channel 1." "0: Disable asynchronous DMA request for channel 1,1: Enable asynchronous DMA request for channel 1" bitfld.long 0x0 0. "EDREQ_0,Enable asynchronous DMA request in stop mode for channel 0." "0: Disable asynchronous DMA request for channel 0,1: Enable asynchronous DMA request for channel 0" group.byte 0x100++0x1F line.byte 0x0 "DCHPRI3,Channel Priority" bitfld.byte 0x0 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x0 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x0 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x0 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1 "DCHPRI2,Channel Priority" bitfld.byte 0x1 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x2 "DCHPRI1,Channel Priority" bitfld.byte 0x2 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x2 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x2 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x2 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x3 "DCHPRI0,Channel Priority" bitfld.byte 0x3 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x3 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x3 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x3 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x4 "DCHPRI7,Channel Priority" bitfld.byte 0x4 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x4 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x4 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x4 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x5 "DCHPRI6,Channel Priority" bitfld.byte 0x5 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x5 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x5 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x5 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x6 "DCHPRI5,Channel Priority" bitfld.byte 0x6 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x6 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x6 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x6 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x7 "DCHPRI4,Channel Priority" bitfld.byte 0x7 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x7 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x7 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x7 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x8 "DCHPRI11,Channel Priority" bitfld.byte 0x8 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x8 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x8 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x8 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x9 "DCHPRI10,Channel Priority" bitfld.byte 0x9 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x9 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x9 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x9 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xA "DCHPRI9,Channel Priority" bitfld.byte 0xA 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xA 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xA 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xA 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xB "DCHPRI8,Channel Priority" bitfld.byte 0xB 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xB 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xB 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xB 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xC "DCHPRI15,Channel Priority" bitfld.byte 0xC 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xC 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xC 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xC 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xD "DCHPRI14,Channel Priority" bitfld.byte 0xD 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xD 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xD 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xD 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xE "DCHPRI13,Channel Priority" bitfld.byte 0xE 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xE 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xE 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xE 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xF "DCHPRI12,Channel Priority" bitfld.byte 0xF 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xF 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xF 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xF 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x10 "DCHPRI19,Channel Priority" bitfld.byte 0x10 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x10 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x10 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x10 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x11 "DCHPRI18,Channel Priority" bitfld.byte 0x11 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x11 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x11 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x11 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x12 "DCHPRI17,Channel Priority" bitfld.byte 0x12 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x12 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x12 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x12 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x13 "DCHPRI16,Channel Priority" bitfld.byte 0x13 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x13 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x13 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x13 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x14 "DCHPRI23,Channel Priority" bitfld.byte 0x14 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x14 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x14 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x14 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x15 "DCHPRI22,Channel Priority" bitfld.byte 0x15 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x15 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x15 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x15 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x16 "DCHPRI21,Channel Priority" bitfld.byte 0x16 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x16 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x16 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x16 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x17 "DCHPRI20,Channel Priority" bitfld.byte 0x17 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x17 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x17 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x17 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x18 "DCHPRI27,Channel Priority" bitfld.byte 0x18 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x18 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x18 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x18 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x19 "DCHPRI26,Channel Priority" bitfld.byte 0x19 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x19 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x19 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x19 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1A "DCHPRI25,Channel Priority" bitfld.byte 0x1A 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1A 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1A 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1A 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1B "DCHPRI24,Channel Priority" bitfld.byte 0x1B 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1B 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1B 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1B 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1C "DCHPRI31,Channel Priority" bitfld.byte 0x1C 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1C 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1C 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1C 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1D "DCHPRI30,Channel Priority" bitfld.byte 0x1D 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1D 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1D 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1D 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1E "DCHPRI29,Channel Priority" bitfld.byte 0x1E 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1E 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1E 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1E 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1F "DCHPRI28,Channel Priority" bitfld.byte 0x1F 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1F 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1F 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1F 0.--3. 1. "CHPRI,Channel n Arbitration Priority" group.long 0x1000++0x3 line.long 0x0 "TCD0_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1004++0x3 line.word 0x0 "TCD0_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD0_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0xB line.long 0x0 "TCD0_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD0_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD0_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1014++0x3 line.word 0x0 "TCD0_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD0_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1016++0x1 line.word 0x0 "TCD0_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1018++0x3 line.long 0x0 "TCD0_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x101C++0x3 line.word 0x0 "TCD0_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD0_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x101E++0x1 line.word 0x0 "TCD0_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1020++0x3 line.long 0x0 "TCD1_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1024++0x3 line.word 0x0 "TCD1_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD1_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0xB line.long 0x0 "TCD1_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD1_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD1_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1034++0x3 line.word 0x0 "TCD1_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD1_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1036++0x1 line.word 0x0 "TCD1_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1038++0x3 line.long 0x0 "TCD1_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x103C++0x3 line.word 0x0 "TCD1_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD1_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x103E++0x1 line.word 0x0 "TCD1_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1040++0x3 line.long 0x0 "TCD2_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1044++0x3 line.word 0x0 "TCD2_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD2_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0xB line.long 0x0 "TCD2_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD2_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD2_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1054++0x3 line.word 0x0 "TCD2_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD2_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1056++0x1 line.word 0x0 "TCD2_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1058++0x3 line.long 0x0 "TCD2_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x105C++0x3 line.word 0x0 "TCD2_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD2_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x105E++0x1 line.word 0x0 "TCD2_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1060++0x3 line.long 0x0 "TCD3_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1064++0x3 line.word 0x0 "TCD3_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD3_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0xB line.long 0x0 "TCD3_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD3_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD3_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1074++0x3 line.word 0x0 "TCD3_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD3_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1076++0x1 line.word 0x0 "TCD3_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1078++0x3 line.long 0x0 "TCD3_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x107C++0x3 line.word 0x0 "TCD3_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD3_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x107E++0x1 line.word 0x0 "TCD3_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1080++0x3 line.long 0x0 "TCD4_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1084++0x3 line.word 0x0 "TCD4_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD4_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0xB line.long 0x0 "TCD4_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD4_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD4_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1094++0x3 line.word 0x0 "TCD4_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD4_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1096++0x1 line.word 0x0 "TCD4_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1098++0x3 line.long 0x0 "TCD4_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x109C++0x3 line.word 0x0 "TCD4_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD4_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x109E++0x1 line.word 0x0 "TCD4_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10A0++0x3 line.long 0x0 "TCD5_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10A4++0x3 line.word 0x0 "TCD5_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD5_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0xB line.long 0x0 "TCD5_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD5_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD5_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10B4++0x3 line.word 0x0 "TCD5_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD5_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10B6++0x1 line.word 0x0 "TCD5_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10B8++0x3 line.long 0x0 "TCD5_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10BC++0x3 line.word 0x0 "TCD5_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD5_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10BE++0x1 line.word 0x0 "TCD5_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10C0++0x3 line.long 0x0 "TCD6_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10C4++0x3 line.word 0x0 "TCD6_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD6_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0xB line.long 0x0 "TCD6_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD6_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD6_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10D4++0x3 line.word 0x0 "TCD6_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD6_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10D6++0x1 line.word 0x0 "TCD6_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10D8++0x3 line.long 0x0 "TCD6_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10DC++0x3 line.word 0x0 "TCD6_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD6_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10DE++0x1 line.word 0x0 "TCD6_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10E0++0x3 line.long 0x0 "TCD7_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10E4++0x3 line.word 0x0 "TCD7_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD7_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0xB line.long 0x0 "TCD7_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD7_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD7_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10F4++0x3 line.word 0x0 "TCD7_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD7_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10F6++0x1 line.word 0x0 "TCD7_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10F8++0x3 line.long 0x0 "TCD7_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10FC++0x3 line.word 0x0 "TCD7_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD7_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10FE++0x1 line.word 0x0 "TCD7_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1100++0x3 line.long 0x0 "TCD8_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1104++0x3 line.word 0x0 "TCD8_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD8_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0xB line.long 0x0 "TCD8_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD8_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD8_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1114++0x3 line.word 0x0 "TCD8_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD8_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1116++0x1 line.word 0x0 "TCD8_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1118++0x3 line.long 0x0 "TCD8_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x111C++0x3 line.word 0x0 "TCD8_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD8_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x111E++0x1 line.word 0x0 "TCD8_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1120++0x3 line.long 0x0 "TCD9_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1124++0x3 line.word 0x0 "TCD9_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD9_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0xB line.long 0x0 "TCD9_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD9_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD9_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1134++0x3 line.word 0x0 "TCD9_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD9_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1136++0x1 line.word 0x0 "TCD9_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1138++0x3 line.long 0x0 "TCD9_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x113C++0x3 line.word 0x0 "TCD9_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD9_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x113E++0x1 line.word 0x0 "TCD9_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1140++0x3 line.long 0x0 "TCD10_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1144++0x3 line.word 0x0 "TCD10_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD10_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0xB line.long 0x0 "TCD10_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD10_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD10_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1154++0x3 line.word 0x0 "TCD10_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD10_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1156++0x1 line.word 0x0 "TCD10_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1158++0x3 line.long 0x0 "TCD10_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x115C++0x3 line.word 0x0 "TCD10_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD10_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x115E++0x1 line.word 0x0 "TCD10_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1160++0x3 line.long 0x0 "TCD11_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1164++0x3 line.word 0x0 "TCD11_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD11_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0xB line.long 0x0 "TCD11_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD11_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD11_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1174++0x3 line.word 0x0 "TCD11_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD11_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1176++0x1 line.word 0x0 "TCD11_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1178++0x3 line.long 0x0 "TCD11_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x117C++0x3 line.word 0x0 "TCD11_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD11_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x117E++0x1 line.word 0x0 "TCD11_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1180++0x3 line.long 0x0 "TCD12_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1184++0x3 line.word 0x0 "TCD12_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD12_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0xB line.long 0x0 "TCD12_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD12_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD12_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1194++0x3 line.word 0x0 "TCD12_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD12_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1196++0x1 line.word 0x0 "TCD12_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1198++0x3 line.long 0x0 "TCD12_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x119C++0x3 line.word 0x0 "TCD12_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD12_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x119E++0x1 line.word 0x0 "TCD12_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11A0++0x3 line.long 0x0 "TCD13_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11A4++0x3 line.word 0x0 "TCD13_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD13_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0xB line.long 0x0 "TCD13_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD13_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD13_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11B4++0x3 line.word 0x0 "TCD13_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD13_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11B6++0x1 line.word 0x0 "TCD13_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11B8++0x3 line.long 0x0 "TCD13_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11BC++0x3 line.word 0x0 "TCD13_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD13_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11BE++0x1 line.word 0x0 "TCD13_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11C0++0x3 line.long 0x0 "TCD14_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11C4++0x3 line.word 0x0 "TCD14_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD14_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0xB line.long 0x0 "TCD14_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD14_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD14_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11D4++0x3 line.word 0x0 "TCD14_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD14_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11D6++0x1 line.word 0x0 "TCD14_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11D8++0x3 line.long 0x0 "TCD14_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11DC++0x3 line.word 0x0 "TCD14_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD14_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11DE++0x1 line.word 0x0 "TCD14_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11E0++0x3 line.long 0x0 "TCD15_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11E4++0x3 line.word 0x0 "TCD15_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD15_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0xB line.long 0x0 "TCD15_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD15_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD15_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11F4++0x3 line.word 0x0 "TCD15_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD15_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11F6++0x1 line.word 0x0 "TCD15_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11F8++0x3 line.long 0x0 "TCD15_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11FC++0x3 line.word 0x0 "TCD15_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD15_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11FE++0x1 line.word 0x0 "TCD15_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1200++0x3 line.long 0x0 "TCD16_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1204++0x3 line.word 0x0 "TCD16_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD16_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0xB line.long 0x0 "TCD16_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD16_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD16_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1214++0x3 line.word 0x0 "TCD16_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD16_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1216++0x1 line.word 0x0 "TCD16_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1218++0x3 line.long 0x0 "TCD16_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x121C++0x3 line.word 0x0 "TCD16_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD16_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x121E++0x1 line.word 0x0 "TCD16_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1220++0x3 line.long 0x0 "TCD17_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1224++0x3 line.word 0x0 "TCD17_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD17_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0xB line.long 0x0 "TCD17_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD17_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD17_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1234++0x3 line.word 0x0 "TCD17_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD17_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1236++0x1 line.word 0x0 "TCD17_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1238++0x3 line.long 0x0 "TCD17_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x123C++0x3 line.word 0x0 "TCD17_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD17_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x123E++0x1 line.word 0x0 "TCD17_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1240++0x3 line.long 0x0 "TCD18_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1244++0x3 line.word 0x0 "TCD18_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD18_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0xB line.long 0x0 "TCD18_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD18_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD18_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1254++0x3 line.word 0x0 "TCD18_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD18_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1256++0x1 line.word 0x0 "TCD18_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1258++0x3 line.long 0x0 "TCD18_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x125C++0x3 line.word 0x0 "TCD18_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD18_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x125E++0x1 line.word 0x0 "TCD18_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1260++0x3 line.long 0x0 "TCD19_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1264++0x3 line.word 0x0 "TCD19_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD19_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0xB line.long 0x0 "TCD19_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD19_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD19_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1274++0x3 line.word 0x0 "TCD19_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD19_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1276++0x1 line.word 0x0 "TCD19_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1278++0x3 line.long 0x0 "TCD19_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x127C++0x3 line.word 0x0 "TCD19_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD19_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x127E++0x1 line.word 0x0 "TCD19_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1280++0x3 line.long 0x0 "TCD20_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1284++0x3 line.word 0x0 "TCD20_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD20_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0xB line.long 0x0 "TCD20_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD20_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD20_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1294++0x3 line.word 0x0 "TCD20_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD20_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1296++0x1 line.word 0x0 "TCD20_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1298++0x3 line.long 0x0 "TCD20_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x129C++0x3 line.word 0x0 "TCD20_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD20_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x129E++0x1 line.word 0x0 "TCD20_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12A0++0x3 line.long 0x0 "TCD21_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12A4++0x3 line.word 0x0 "TCD21_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD21_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0xB line.long 0x0 "TCD21_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD21_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD21_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12B4++0x3 line.word 0x0 "TCD21_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD21_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12B6++0x1 line.word 0x0 "TCD21_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12B8++0x3 line.long 0x0 "TCD21_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12BC++0x3 line.word 0x0 "TCD21_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD21_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12BE++0x1 line.word 0x0 "TCD21_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12C0++0x3 line.long 0x0 "TCD22_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12C4++0x3 line.word 0x0 "TCD22_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD22_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0xB line.long 0x0 "TCD22_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD22_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD22_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12D4++0x3 line.word 0x0 "TCD22_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD22_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12D6++0x1 line.word 0x0 "TCD22_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12D8++0x3 line.long 0x0 "TCD22_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12DC++0x3 line.word 0x0 "TCD22_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD22_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12DE++0x1 line.word 0x0 "TCD22_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12E0++0x3 line.long 0x0 "TCD23_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12E4++0x3 line.word 0x0 "TCD23_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD23_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0xB line.long 0x0 "TCD23_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD23_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD23_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12F4++0x3 line.word 0x0 "TCD23_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD23_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12F6++0x1 line.word 0x0 "TCD23_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12F8++0x3 line.long 0x0 "TCD23_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12FC++0x3 line.word 0x0 "TCD23_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD23_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12FE++0x1 line.word 0x0 "TCD23_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1300++0x3 line.long 0x0 "TCD24_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1304++0x3 line.word 0x0 "TCD24_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD24_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0xB line.long 0x0 "TCD24_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD24_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD24_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1314++0x3 line.word 0x0 "TCD24_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD24_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1316++0x1 line.word 0x0 "TCD24_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1318++0x3 line.long 0x0 "TCD24_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x131C++0x3 line.word 0x0 "TCD24_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD24_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x131E++0x1 line.word 0x0 "TCD24_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1320++0x3 line.long 0x0 "TCD25_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1324++0x3 line.word 0x0 "TCD25_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD25_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0xB line.long 0x0 "TCD25_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD25_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD25_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1334++0x3 line.word 0x0 "TCD25_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD25_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1336++0x1 line.word 0x0 "TCD25_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1338++0x3 line.long 0x0 "TCD25_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x133C++0x3 line.word 0x0 "TCD25_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD25_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x133E++0x1 line.word 0x0 "TCD25_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1340++0x3 line.long 0x0 "TCD26_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1344++0x3 line.word 0x0 "TCD26_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD26_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0xB line.long 0x0 "TCD26_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD26_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD26_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1354++0x3 line.word 0x0 "TCD26_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD26_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1356++0x1 line.word 0x0 "TCD26_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1358++0x3 line.long 0x0 "TCD26_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x135C++0x3 line.word 0x0 "TCD26_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD26_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x135E++0x1 line.word 0x0 "TCD26_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1360++0x3 line.long 0x0 "TCD27_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1364++0x3 line.word 0x0 "TCD27_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD27_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0xB line.long 0x0 "TCD27_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD27_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD27_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1374++0x3 line.word 0x0 "TCD27_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD27_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1376++0x1 line.word 0x0 "TCD27_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1378++0x3 line.long 0x0 "TCD27_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x137C++0x3 line.word 0x0 "TCD27_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD27_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x137E++0x1 line.word 0x0 "TCD27_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1380++0x3 line.long 0x0 "TCD28_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1384++0x3 line.word 0x0 "TCD28_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD28_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0xB line.long 0x0 "TCD28_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD28_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD28_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1394++0x3 line.word 0x0 "TCD28_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD28_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1396++0x1 line.word 0x0 "TCD28_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1398++0x3 line.long 0x0 "TCD28_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x139C++0x3 line.word 0x0 "TCD28_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD28_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x139E++0x1 line.word 0x0 "TCD28_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13A0++0x3 line.long 0x0 "TCD29_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13A4++0x3 line.word 0x0 "TCD29_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD29_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0xB line.long 0x0 "TCD29_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD29_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD29_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13B4++0x3 line.word 0x0 "TCD29_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD29_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13B6++0x1 line.word 0x0 "TCD29_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13B8++0x3 line.long 0x0 "TCD29_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13BC++0x3 line.word 0x0 "TCD29_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD29_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13BE++0x1 line.word 0x0 "TCD29_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13C0++0x3 line.long 0x0 "TCD30_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13C4++0x3 line.word 0x0 "TCD30_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD30_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0xB line.long 0x0 "TCD30_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD30_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD30_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13D4++0x3 line.word 0x0 "TCD30_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD30_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13D6++0x1 line.word 0x0 "TCD30_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13D8++0x3 line.long 0x0 "TCD30_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13DC++0x3 line.word 0x0 "TCD30_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD30_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13DE++0x1 line.word 0x0 "TCD30_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13E0++0x3 line.long 0x0 "TCD31_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13E4++0x3 line.word 0x0 "TCD31_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD31_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0xB line.long 0x0 "TCD31_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD31_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD31_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13F4++0x3 line.word 0x0 "TCD31_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD31_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13F6++0x1 line.word 0x0 "TCD31_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13F8++0x3 line.long 0x0 "TCD31_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13FC++0x3 line.word 0x0 "TCD31_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD31_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13FE++0x1 line.word 0x0 "TCD31_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" tree.end endif sif (cpuis("IMXRT1166-CM7")) tree "DMA0" base ad:0x40070000 group.long 0x0++0x3 line.long 0x0 "CR,Control" rbitfld.long 0x0 31. "ACTIVE,eDMA Active Status" "0: eDMA is idle,1: eDMA is executing a channel" hexmask.long.byte 0x0 24.--30. 1. "VERSION,eDMA version number" newline bitfld.long 0x0 17. "CX,Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" bitfld.long 0x0 16. "ECX,Error Cancel Transfer" "0: Normal operation,1: Cancel the remaining data transfer" newline bitfld.long 0x0 10. "GRP1PRI,Channel Group 1 Priority" "0,1" bitfld.long 0x0 8. "GRP0PRI,Channel Group 0 Priority" "0,1" newline bitfld.long 0x0 7. "EMLM,Enable Minor Loop Mapping" "0: Disabled,1: Enabled" bitfld.long 0x0 6. "CLM,Continuous Link Mode" "0: Continuous link mode is off,1: Continuous link mode is on" newline bitfld.long 0x0 5. "HALT,Halt eDMA Operations" "0: Normal operation,1: eDMA operations halted" bitfld.long 0x0 4. "HOE,Halt On Error" "0: Normal operation,1: Error causes HALT field to be automatically set.." newline bitfld.long 0x0 3. "ERGA,Enable Round Robin Group Arbitration" "0: Fixed priority arbitration,1: Round robin arbitration" bitfld.long 0x0 2. "ERCA,Enable Round Robin Channel Arbitration" "0: Fixed priority arbitration within each group,1: Round robin arbitration within each group" newline bitfld.long 0x0 1. "EDBG,Enable Debug" "0: When the chip is in Debug mode the eDMA..,1: When the chip is in debug mode the DMA stalls.." rgroup.long 0x4++0x3 line.long 0x0 "ES,Error Status" bitfld.long 0x0 31. "VLD,Logical OR of all ERR status fields" "0: No ERR fields are 1,1: At least one ERR field has a value of 1.." bitfld.long 0x0 16. "ECX,Transfer Canceled" "0: No canceled transfers,1: The most-recently recorded entry was a canceled.." newline bitfld.long 0x0 15. "GPE,Group Priority Error" "0: No group priority error.,1: The most-recently recorded error was a.." bitfld.long 0x0 14. "CPE,Channel Priority Error" "0: No channel priority error.,1: The most-recently recorded error was a.." newline hexmask.long.byte 0x0 8.--12. 1. "ERRCHN,Error Channel Number or Canceled Channel Number" bitfld.long 0x0 7. "SAE,Source Address Error" "0: No source address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 6. "SOE,Source Offset Error" "0: No source offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 5. "DAE,Destination Address Error" "0: No destination address configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 4. "DOE,Destination Offset Error" "0: No destination offset configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 3. "NCE,NBYTES/CITER Configuration Error" "0: No NBYTES/CITER configuration error.,1: The most-recently recorded error was a.." newline bitfld.long 0x0 2. "SGE,Scatter/Gather Configuration Error" "0: No scatter/gather configuration error.,1: The most-recently recorded error was a.." bitfld.long 0x0 1. "SBE,Source Bus Error" "0: No source bus error.,1: The most-recently recorded error was a bus error.." newline bitfld.long 0x0 0. "DBE,Destination Bus Error" "0: No destination bus error.,1: The most-recently recorded error was a bus error.." group.long 0xC++0x3 line.long 0x0 "ERQ,Enable Request" bitfld.long 0x0 31. "ERQ31,Enable DMA Request 31" "0: The DMA request signal for channel 31 is disabled,1: The DMA request signal for channel 31 is enabled" bitfld.long 0x0 30. "ERQ30,Enable DMA Request 30" "0: The DMA request signal for channel 30 is disabled,1: The DMA request signal for channel 30 is enabled" newline bitfld.long 0x0 29. "ERQ29,Enable DMA Request 29" "0: The DMA request signal for channel 29 is disabled,1: The DMA request signal for channel 29 is enabled" bitfld.long 0x0 28. "ERQ28,Enable DMA Request 28" "0: The DMA request signal for channel 28 is disabled,1: The DMA request signal for channel 28 is enabled" newline bitfld.long 0x0 27. "ERQ27,Enable DMA Request 27" "0: The DMA request signal for channel 27 is disabled,1: The DMA request signal for channel 27 is enabled" bitfld.long 0x0 26. "ERQ26,Enable DMA Request 26" "0: The DMA request signal for channel 26 is disabled,1: The DMA request signal for channel 26 is enabled" newline bitfld.long 0x0 25. "ERQ25,Enable DMA Request 25" "0: The DMA request signal for channel 25 is disabled,1: The DMA request signal for channel 25 is enabled" bitfld.long 0x0 24. "ERQ24,Enable DMA Request 24" "0: The DMA request signal for channel 24 is disabled,1: The DMA request signal for channel 24 is enabled" newline bitfld.long 0x0 23. "ERQ23,Enable DMA Request 23" "0: The DMA request signal for channel 23 is disabled,1: The DMA request signal for channel 23 is enabled" bitfld.long 0x0 22. "ERQ22,Enable DMA Request 22" "0: The DMA request signal for channel 22 is disabled,1: The DMA request signal for channel 22 is enabled" newline bitfld.long 0x0 21. "ERQ21,Enable DMA Request 21" "0: The DMA request signal for channel 21 is disabled,1: The DMA request signal for channel 21 is enabled" bitfld.long 0x0 20. "ERQ20,Enable DMA Request 20" "0: The DMA request signal for channel 20 is disabled,1: The DMA request signal for channel 20 is enabled" newline bitfld.long 0x0 19. "ERQ19,Enable DMA Request 19" "0: The DMA request signal for channel 19 is disabled,1: The DMA request signal for channel 19 is enabled" bitfld.long 0x0 18. "ERQ18,Enable DMA Request 18" "0: The DMA request signal for channel 18 is disabled,1: The DMA request signal for channel 18 is enabled" newline bitfld.long 0x0 17. "ERQ17,Enable DMA Request 17" "0: The DMA request signal for channel 17 is disabled,1: The DMA request signal for channel 17 is enabled" bitfld.long 0x0 16. "ERQ16,Enable DMA Request 16" "0: The DMA request signal for channel 16 is disabled,1: The DMA request signal for channel 16 is enabled" newline bitfld.long 0x0 15. "ERQ15,Enable DMA Request 15" "0: The DMA request signal for channel 15 is disabled,1: The DMA request signal for channel 15 is enabled" bitfld.long 0x0 14. "ERQ14,Enable DMA Request 14" "0: The DMA request signal for channel 14 is disabled,1: The DMA request signal for channel 14 is enabled" newline bitfld.long 0x0 13. "ERQ13,Enable DMA Request 13" "0: The DMA request signal for channel 13 is disabled,1: The DMA request signal for channel 13 is enabled" bitfld.long 0x0 12. "ERQ12,Enable DMA Request 12" "0: The DMA request signal for channel 12 is disabled,1: The DMA request signal for channel 12 is enabled" newline bitfld.long 0x0 11. "ERQ11,Enable DMA Request 11" "0: The DMA request signal for channel 11 is disabled,1: The DMA request signal for channel 11 is enabled" bitfld.long 0x0 10. "ERQ10,Enable DMA Request 10" "0: The DMA request signal for channel 10 is disabled,1: The DMA request signal for channel 10 is enabled" newline bitfld.long 0x0 9. "ERQ9,Enable DMA Request 9" "0: The DMA request signal for channel 9 is disabled,1: The DMA request signal for channel 9 is enabled" bitfld.long 0x0 8. "ERQ8,Enable DMA Request 8" "0: The DMA request signal for channel 8 is disabled,1: The DMA request signal for channel 8 is enabled" newline bitfld.long 0x0 7. "ERQ7,Enable DMA Request 7" "0: The DMA request signal for channel 7 is disabled,1: The DMA request signal for channel 7 is enabled" bitfld.long 0x0 6. "ERQ6,Enable DMA Request 6" "0: The DMA request signal for channel 6 is disabled,1: The DMA request signal for channel 6 is enabled" newline bitfld.long 0x0 5. "ERQ5,Enable DMA Request 5" "0: The DMA request signal for channel 5 is disabled,1: The DMA request signal for channel 5 is enabled" bitfld.long 0x0 4. "ERQ4,Enable DMA Request 4" "0: The DMA request signal for channel 4 is disabled,1: The DMA request signal for channel 4 is enabled" newline bitfld.long 0x0 3. "ERQ3,Enable DMA Request 3" "0: The DMA request signal for channel 3 is disabled,1: The DMA request signal for channel 3 is enabled" bitfld.long 0x0 2. "ERQ2,Enable DMA Request 2" "0: The DMA request signal for channel 2 is disabled,1: The DMA request signal for channel 2 is enabled" newline bitfld.long 0x0 1. "ERQ1,Enable DMA Request 1" "0: The DMA request signal for channel 1 is disabled,1: The DMA request signal for channel 1 is enabled" bitfld.long 0x0 0. "ERQ0,Enable DMA Request 0" "0: The DMA request signal for channel 0 is disabled,1: The DMA request signal for channel 0 is enabled" group.long 0x14++0x3 line.long 0x0 "EEI,Enable Error Interrupt" bitfld.long 0x0 31. "EEI31,Enable Error Interrupt 31" "0: An error on channel 31 does not generate an..,1: An error on channel 31 generates an error.." bitfld.long 0x0 30. "EEI30,Enable Error Interrupt 30" "0: An error on channel 30 does not generate an..,1: An error on channel 30 generates an error.." newline bitfld.long 0x0 29. "EEI29,Enable Error Interrupt 29" "0: An error on channel 29 does not generate an..,1: An error on channel 29 generates an error.." bitfld.long 0x0 28. "EEI28,Enable Error Interrupt 28" "0: An error on channel 28 does not generate an..,1: An error on channel 28 generates an error.." newline bitfld.long 0x0 27. "EEI27,Enable Error Interrupt 27" "0: An error on channel 27 does not generate an..,1: An error on channel 27 generates an error.." bitfld.long 0x0 26. "EEI26,Enable Error Interrupt 26" "0: An error on channel 26 does not generate an..,1: An error on channel 26 generates an error.." newline bitfld.long 0x0 25. "EEI25,Enable Error Interrupt 25" "0: An error on channel 25 does not generate an..,1: An error on channel 25 generates an error.." bitfld.long 0x0 24. "EEI24,Enable Error Interrupt 24" "0: An error on channel 24 does not generate an..,1: An error on channel 24 generates an error.." newline bitfld.long 0x0 23. "EEI23,Enable Error Interrupt 23" "0: An error on channel 23 does not generate an..,1: An error on channel 23 generates an error.." bitfld.long 0x0 22. "EEI22,Enable Error Interrupt 22" "0: An error on channel 22 does not generate an..,1: An error on channel 22 generates an error.." newline bitfld.long 0x0 21. "EEI21,Enable Error Interrupt 21" "0: An error on channel 21 does not generate an..,1: An error on channel 21 generates an error.." bitfld.long 0x0 20. "EEI20,Enable Error Interrupt 20" "0: An error on channel 20 does not generate an..,1: An error on channel 20 generates an error.." newline bitfld.long 0x0 19. "EEI19,Enable Error Interrupt 19" "0: An error on channel 19 does not generate an..,1: An error on channel 19 generates an error.." bitfld.long 0x0 18. "EEI18,Enable Error Interrupt 18" "0: An error on channel 18 does not generate an..,1: An error on channel 18 generates an error.." newline bitfld.long 0x0 17. "EEI17,Enable Error Interrupt 17" "0: An error on channel 17 does not generate an..,1: An error on channel 17 generates an error.." bitfld.long 0x0 16. "EEI16,Enable Error Interrupt 16" "0: An error on channel 16 does not generate an..,1: An error on channel 16 generates an error.." newline bitfld.long 0x0 15. "EEI15,Enable Error Interrupt 15" "0: An error on channel 15 does not generate an..,1: An error on channel 15 generates an error.." bitfld.long 0x0 14. "EEI14,Enable Error Interrupt 14" "0: An error on channel 14 does not generate an..,1: An error on channel 14 generates an error.." newline bitfld.long 0x0 13. "EEI13,Enable Error Interrupt 13" "0: An error on channel 13 does not generate an..,1: An error on channel 13 generates an error.." bitfld.long 0x0 12. "EEI12,Enable Error Interrupt 12" "0: An error on channel 12 does not generate an..,1: An error on channel 12 generates an error.." newline bitfld.long 0x0 11. "EEI11,Enable Error Interrupt 11" "0: An error on channel 11 does not generate an..,1: An error on channel 11 generates an error.." bitfld.long 0x0 10. "EEI10,Enable Error Interrupt 10" "0: An error on channel 10 does not generate an..,1: An error on channel 10 generates an error.." newline bitfld.long 0x0 9. "EEI9,Enable Error Interrupt 9" "0: An error on channel 9 does not generate an error..,1: An error on channel 9 generates an error.." bitfld.long 0x0 8. "EEI8,Enable Error Interrupt 8" "0: An error on channel 8 does not generate an error..,1: An error on channel 8 generates an error.." newline bitfld.long 0x0 7. "EEI7,Enable Error Interrupt 7" "0: An error on channel 7 does not generate an error..,1: An error on channel 7 generates an error.." bitfld.long 0x0 6. "EEI6,Enable Error Interrupt 6" "0: An error on channel 6 does not generate an error..,1: An error on channel 6 generates an error.." newline bitfld.long 0x0 5. "EEI5,Enable Error Interrupt 5" "0: An error on channel 5 does not generate an error..,1: An error on channel 5 generates an error.." bitfld.long 0x0 4. "EEI4,Enable Error Interrupt 4" "0: An error on channel 4 does not generate an error..,1: An error on channel 4 generates an error.." newline bitfld.long 0x0 3. "EEI3,Enable Error Interrupt 3" "0: An error on channel 3 does not generate an error..,1: An error on channel 3 generates an error.." bitfld.long 0x0 2. "EEI2,Enable Error Interrupt 2" "0: An error on channel 2 does not generate an error..,1: An error on channel 2 generates an error.." newline bitfld.long 0x0 1. "EEI1,Enable Error Interrupt 1" "0: An error on channel 1 does not generate an error..,1: An error on channel 1 generates an error.." bitfld.long 0x0 0. "EEI0,Enable Error Interrupt 0" "0: An error on channel 0 does not generate an error..,1: An error on channel 0 generates an error.." group.byte 0x18++0x7 line.byte 0x0 "CEEI,Clear Enable Error Interrupt" bitfld.byte 0x0 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x0 6. "CAEE,Clear All Enable Error Interrupts" "0: Write 0 only to the EEI field specified in the..,1: Write 0 to all fields in EEI" newline hexmask.byte 0x0 0.--4. 1. "CEEI,Clear Enable Error Interrupt" line.byte 0x1 "SEEI,Set Enable Error Interrupt" bitfld.byte 0x1 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x1 6. "SAEE,Set All Enable Error Interrupts" "0: Write 1 only to the EEI field specified in the..,1: Writes 1 to all fields in EEI" newline hexmask.byte 0x1 0.--4. 1. "SEEI,Set Enable Error Interrupt" line.byte 0x2 "CERQ,Clear Enable Request" bitfld.byte 0x2 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x2 6. "CAER,Clear All Enable Requests" "0: Write 0 to only the ERQ field specified in the..,1: Write 0 to all fields in ERQ" newline hexmask.byte 0x2 0.--4. 1. "CERQ,Clear Enable Request" line.byte 0x3 "SERQ,Set Enable Request" bitfld.byte 0x3 7. "NOP,No Op Enable" "0: Normal operation,1: No operation ignore the other fields in this.." bitfld.byte 0x3 6. "SAER,Set All Enable Requests" "0: Write 1 to only the ERQ field specified in the..,1: Write 1 to all fields in ERQ" newline hexmask.byte 0x3 0.--4. 1. "SERQ,Set Enable Request" line.byte 0x4 "CDNE,Clear DONE Status Bit" bitfld.byte 0x4 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x4 6. "CADN,Clears All DONE fields" "0: Writes 0 to only the TCDn_CSR[DONE] field..,1: Writes 0 to all bits in TCDn_CSR[DONE]" newline hexmask.byte 0x4 0.--4. 1. "CDNE,Clear DONE field" line.byte 0x5 "SSRT,Set START Bit" bitfld.byte 0x5 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x5 6. "SAST,Set All START fields (activates all channels)" "0: Write 1 to only the TCDn_CSR[START] field..,1: Write 1 to all bits in TCDn_CSR[START]" newline hexmask.byte 0x5 0.--4. 1. "SSRT,Set START field" line.byte 0x6 "CERR,Clear Error" bitfld.byte 0x6 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x6 6. "CAEI,Clear All Error Indicators" "0: Write 0 to only the ERR field specified in the..,1: Write 0 to all fields in ERR" newline hexmask.byte 0x6 0.--4. 1. "CERR,Clear Error Indicator" line.byte 0x7 "CINT,Clear Interrupt Request" bitfld.byte 0x7 7. "NOP,No Op Enable" "0: Normal operation,1: No operation; all other fields in this register.." bitfld.byte 0x7 6. "CAIR,Clear All Interrupt Requests" "0: Clear only the INT field specified in the CINT..,1: Clear all bits in INT" newline hexmask.byte 0x7 0.--4. 1. "CINT,Clear Interrupt Request" group.long 0x24++0x3 line.long 0x0 "INT,Interrupt Request" eventfld.long 0x0 31. "INT31,Interrupt Request 31" "0: The interrupt request for channel 31 is cleared,1: The interrupt request for channel 31 is active" eventfld.long 0x0 30. "INT30,Interrupt Request 30" "0: The interrupt request for channel 30 is cleared,1: The interrupt request for channel 30 is active" newline eventfld.long 0x0 29. "INT29,Interrupt Request 29" "0: The interrupt request for channel 29 is cleared,1: The interrupt request for channel 29 is active" eventfld.long 0x0 28. "INT28,Interrupt Request 28" "0: The interrupt request for channel 28 is cleared,1: The interrupt request for channel 28 is active" newline eventfld.long 0x0 27. "INT27,Interrupt Request 27" "0: The interrupt request for channel 27 is cleared,1: The interrupt request for channel 27 is active" eventfld.long 0x0 26. "INT26,Interrupt Request 26" "0: The interrupt request for channel 26 is cleared,1: The interrupt request for channel 26 is active" newline eventfld.long 0x0 25. "INT25,Interrupt Request 25" "0: The interrupt request for channel 25 is cleared,1: The interrupt request for channel 25 is active" eventfld.long 0x0 24. "INT24,Interrupt Request 24" "0: The interrupt request for channel 24 is cleared,1: The interrupt request for channel 24 is active" newline eventfld.long 0x0 23. "INT23,Interrupt Request 23" "0: The interrupt request for channel 23 is cleared,1: The interrupt request for channel 23 is active" eventfld.long 0x0 22. "INT22,Interrupt Request 22" "0: The interrupt request for channel 22 is cleared,1: The interrupt request for channel 22 is active" newline eventfld.long 0x0 21. "INT21,Interrupt Request 21" "0: The interrupt request for channel 21 is cleared,1: The interrupt request for channel 21 is active" eventfld.long 0x0 20. "INT20,Interrupt Request 20" "0: The interrupt request for channel 20 is cleared,1: The interrupt request for channel 20 is active" newline eventfld.long 0x0 19. "INT19,Interrupt Request 19" "0: The interrupt request for channel 19 is cleared,1: The interrupt request for channel 19 is active" eventfld.long 0x0 18. "INT18,Interrupt Request 18" "0: The interrupt request for channel 18 is cleared,1: The interrupt request for channel 18 is active" newline eventfld.long 0x0 17. "INT17,Interrupt Request 17" "0: The interrupt request for channel 17 is cleared,1: The interrupt request for channel 17 is active" eventfld.long 0x0 16. "INT16,Interrupt Request 16" "0: The interrupt request for channel 16 is cleared,1: The interrupt request for channel 16 is active" newline eventfld.long 0x0 15. "INT15,Interrupt Request 15" "0: The interrupt request for channel 15 is cleared,1: The interrupt request for channel 15 is active" eventfld.long 0x0 14. "INT14,Interrupt Request 14" "0: The interrupt request for channel 14 is cleared,1: The interrupt request for channel 14 is active" newline eventfld.long 0x0 13. "INT13,Interrupt Request 13" "0: The interrupt request for channel 13 is cleared,1: The interrupt request for channel 13 is active" eventfld.long 0x0 12. "INT12,Interrupt Request 12" "0: The interrupt request for channel 12 is cleared,1: The interrupt request for channel 12 is active" newline eventfld.long 0x0 11. "INT11,Interrupt Request 11" "0: The interrupt request for channel 11 is cleared,1: The interrupt request for channel 11 is active" eventfld.long 0x0 10. "INT10,Interrupt Request 10" "0: The interrupt request for channel 10 is cleared,1: The interrupt request for channel 10 is active" newline eventfld.long 0x0 9. "INT9,Interrupt Request 9" "0: The interrupt request for channel 9 is cleared,1: The interrupt request for channel 9 is active" eventfld.long 0x0 8. "INT8,Interrupt Request 8" "0: The interrupt request for channel 8 is cleared,1: The interrupt request for channel 8 is active" newline eventfld.long 0x0 7. "INT7,Interrupt Request 7" "0: The interrupt request for channel 7 is cleared,1: The interrupt request for channel 7 is active" eventfld.long 0x0 6. "INT6,Interrupt Request 6" "0: The interrupt request for channel 6 is cleared,1: The interrupt request for channel 6 is active" newline eventfld.long 0x0 5. "INT5,Interrupt Request 5" "0: The interrupt request for channel 5 is cleared,1: The interrupt request for channel 5 is active" eventfld.long 0x0 4. "INT4,Interrupt Request 4" "0: The interrupt request for channel 4 is cleared,1: The interrupt request for channel 4 is active" newline eventfld.long 0x0 3. "INT3,Interrupt Request 3" "0: The interrupt request for channel 3 is cleared,1: The interrupt request for channel 3 is active" eventfld.long 0x0 2. "INT2,Interrupt Request 2" "0: The interrupt request for channel 2 is cleared,1: The interrupt request for channel 2 is active" newline eventfld.long 0x0 1. "INT1,Interrupt Request 1" "0: The interrupt request for channel 1 is cleared,1: The interrupt request for channel 1 is active" eventfld.long 0x0 0. "INT0,Interrupt Request 0" "0: The interrupt request for channel 0 is cleared,1: The interrupt request for channel 0 is active" group.long 0x2C++0x3 line.long 0x0 "ERR,Error" eventfld.long 0x0 31. "ERR31,Error In Channel 31" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 30. "ERR30,Error In Channel 30" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 29. "ERR29,Error In Channel 29" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 28. "ERR28,Error In Channel 28" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 27. "ERR27,Error In Channel 27" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 26. "ERR26,Error In Channel 26" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 25. "ERR25,Error In Channel 25" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 24. "ERR24,Error In Channel 24" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 23. "ERR23,Error In Channel 23" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 22. "ERR22,Error In Channel 22" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 21. "ERR21,Error In Channel 21" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 20. "ERR20,Error In Channel 20" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 19. "ERR19,Error In Channel 19" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 18. "ERR18,Error In Channel 18" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 17. "ERR17,Error In Channel 17" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 16. "ERR16,Error In Channel 16" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 15. "ERR15,Error In Channel 15" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 14. "ERR14,Error In Channel 14" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 13. "ERR13,Error In Channel 13" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 12. "ERR12,Error In Channel 12" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 11. "ERR11,Error In Channel 11" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 10. "ERR10,Error In Channel 10" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 9. "ERR9,Error In Channel 9" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 8. "ERR8,Error In Channel 8" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 7. "ERR7,Error In Channel 7" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 6. "ERR6,Error In Channel 6" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 5. "ERR5,Error In Channel 5" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 4. "ERR4,Error In Channel 4" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 3. "ERR3,Error In Channel 3" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 2. "ERR2,Error In Channel 2" "0: No error in this channel has occurred,1: An error in this channel has occurred" newline eventfld.long 0x0 1. "ERR1,Error In Channel 1" "0: No error in this channel has occurred,1: An error in this channel has occurred" eventfld.long 0x0 0. "ERR0,Error In Channel 0" "0: No error in this channel has occurred,1: An error in this channel has occurred" rgroup.long 0x34++0x3 line.long 0x0 "HRS,Hardware Request Status" bitfld.long 0x0 31. "HRS31,Hardware Request Status Channel 31" "0: A hardware service request for channel 31 is not..,1: A hardware service request for channel 31 is.." bitfld.long 0x0 30. "HRS30,Hardware Request Status Channel 30" "0: A hardware service request for channel 30 is not..,1: A hardware service request for channel 30 is.." newline bitfld.long 0x0 29. "HRS29,Hardware Request Status Channel 29" "0: A hardware service request for channel 29 is not..,1: A hardware service request for channel 29 is.." bitfld.long 0x0 28. "HRS28,Hardware Request Status Channel 28" "0: A hardware service request for channel 28 is not..,1: A hardware service request for channel 28 is.." newline bitfld.long 0x0 27. "HRS27,Hardware Request Status Channel 27" "0: A hardware service request for channel 27 is not..,1: A hardware service request for channel 27 is.." bitfld.long 0x0 26. "HRS26,Hardware Request Status Channel 26" "0: A hardware service request for channel 26 is not..,1: A hardware service request for channel 26 is.." newline bitfld.long 0x0 25. "HRS25,Hardware Request Status Channel 25" "0: A hardware service request for channel 25 is not..,1: A hardware service request for channel 25 is.." bitfld.long 0x0 24. "HRS24,Hardware Request Status Channel 24" "0: A hardware service request for channel 24 is not..,1: A hardware service request for channel 24 is.." newline bitfld.long 0x0 23. "HRS23,Hardware Request Status Channel 23" "0: A hardware service request for channel 23 is not..,1: A hardware service request for channel 23 is.." bitfld.long 0x0 22. "HRS22,Hardware Request Status Channel 22" "0: A hardware service request for channel 22 is not..,1: A hardware service request for channel 22 is.." newline bitfld.long 0x0 21. "HRS21,Hardware Request Status Channel 21" "0: A hardware service request for channel 21 is not..,1: A hardware service request for channel 21 is.." bitfld.long 0x0 20. "HRS20,Hardware Request Status Channel 20" "0: A hardware service request for channel 20 is not..,1: A hardware service request for channel 20 is.." newline bitfld.long 0x0 19. "HRS19,Hardware Request Status Channel 19" "0: A hardware service request for channel 19 is not..,1: A hardware service request for channel 19 is.." bitfld.long 0x0 18. "HRS18,Hardware Request Status Channel 18" "0: A hardware service request for channel 18 is not..,1: A hardware service request for channel 18 is.." newline bitfld.long 0x0 17. "HRS17,Hardware Request Status Channel 17" "0: A hardware service request for channel 17 is not..,1: A hardware service request for channel 17 is.." bitfld.long 0x0 16. "HRS16,Hardware Request Status Channel 16" "0: A hardware service request for channel 16 is not..,1: A hardware service request for channel 16 is.." newline bitfld.long 0x0 15. "HRS15,Hardware Request Status Channel 15" "0: A hardware service request for channel 15 is not..,1: A hardware service request for channel 15 is.." bitfld.long 0x0 14. "HRS14,Hardware Request Status Channel 14" "0: A hardware service request for channel 14 is not..,1: A hardware service request for channel 14 is.." newline bitfld.long 0x0 13. "HRS13,Hardware Request Status Channel 13" "0: A hardware service request for channel 13 is not..,1: A hardware service request for channel 13 is.." bitfld.long 0x0 12. "HRS12,Hardware Request Status Channel 12" "0: A hardware service request for channel 12 is not..,1: A hardware service request for channel 12 is.." newline bitfld.long 0x0 11. "HRS11,Hardware Request Status Channel 11" "0: A hardware service request for channel 11 is not..,1: A hardware service request for channel 11 is.." bitfld.long 0x0 10. "HRS10,Hardware Request Status Channel 10" "0: A hardware service request for channel 10 is not..,1: A hardware service request for channel 10 is.." newline bitfld.long 0x0 9. "HRS9,Hardware Request Status Channel 9" "0: A hardware service request for channel 9 is not..,1: A hardware service request for channel 9 is.." bitfld.long 0x0 8. "HRS8,Hardware Request Status Channel 8" "0: A hardware service request for channel 8 is not..,1: A hardware service request for channel 8 is.." newline bitfld.long 0x0 7. "HRS7,Hardware Request Status Channel 7" "0: A hardware service request for channel 7 is not..,1: A hardware service request for channel 7 is.." bitfld.long 0x0 6. "HRS6,Hardware Request Status Channel 6" "0: A hardware service request for channel 6 is not..,1: A hardware service request for channel 6 is.." newline bitfld.long 0x0 5. "HRS5,Hardware Request Status Channel 5" "0: A hardware service request for channel 5 is not..,1: A hardware service request for channel 5 is.." bitfld.long 0x0 4. "HRS4,Hardware Request Status Channel 4" "0: A hardware service request for channel 4 is not..,1: A hardware service request for channel 4 is.." newline bitfld.long 0x0 3. "HRS3,Hardware Request Status Channel 3" "0: A hardware service request for channel 3 is not..,1: A hardware service request for channel 3 is.." bitfld.long 0x0 2. "HRS2,Hardware Request Status Channel 2" "0: A hardware service request for channel 2 is not..,1: A hardware service request for channel 2 is.." newline bitfld.long 0x0 1. "HRS1,Hardware Request Status Channel 1" "0: A hardware service request for channel 1 is not..,1: A hardware service request for channel 1 is.." bitfld.long 0x0 0. "HRS0,Hardware Request Status Channel 0" "0: A hardware service request for channel 0 is not..,1: A hardware service request for channel 0 is.." group.long 0x44++0x3 line.long 0x0 "EARS,Enable Asynchronous Request in Stop" bitfld.long 0x0 31. "EDREQ_31,Enable asynchronous DMA request in stop mode for channel 31." "0: Disable asynchronous DMA request for channel 31,1: Enable asynchronous DMA request for channel 31" bitfld.long 0x0 30. "EDREQ_30,Enable asynchronous DMA request in stop mode for channel 30." "0: Disable asynchronous DMA request for channel 30,1: Enable asynchronous DMA request for channel 30" newline bitfld.long 0x0 29. "EDREQ_29,Enable asynchronous DMA request in stop mode for channel 29." "0: Disable asynchronous DMA request for channel 29,1: Enable asynchronous DMA request for channel 29" bitfld.long 0x0 28. "EDREQ_28,Enable asynchronous DMA request in stop mode for channel 28." "0: Disable asynchronous DMA request for channel 28,1: Enable asynchronous DMA request for channel 28" newline bitfld.long 0x0 27. "EDREQ_27,Enable asynchronous DMA request in stop mode for channel 27." "0: Disable asynchronous DMA request for channel 27,1: Enable asynchronous DMA request for channel 27" bitfld.long 0x0 26. "EDREQ_26,Enable asynchronous DMA request in stop mode for channel 26." "0: Disable asynchronous DMA request for channel 26,1: Enable asynchronous DMA request for channel 26" newline bitfld.long 0x0 25. "EDREQ_25,Enable asynchronous DMA request in stop mode for channel 25." "0: Disable asynchronous DMA request for channel 25,1: Enable asynchronous DMA request for channel 25" bitfld.long 0x0 24. "EDREQ_24,Enable asynchronous DMA request in stop mode for channel 24." "0: Disable asynchronous DMA request for channel 24,1: Enable asynchronous DMA request for channel 24" newline bitfld.long 0x0 23. "EDREQ_23,Enable asynchronous DMA request in stop mode for channel 23." "0: Disable asynchronous DMA request for channel 23,1: Enable asynchronous DMA request for channel 23" bitfld.long 0x0 22. "EDREQ_22,Enable asynchronous DMA request in stop mode for channel 22." "0: Disable asynchronous DMA request for channel 22,1: Enable asynchronous DMA request for channel 22" newline bitfld.long 0x0 21. "EDREQ_21,Enable asynchronous DMA request in stop mode for channel 21." "0: Disable asynchronous DMA request for channel 21,1: Enable asynchronous DMA request for channel 21" bitfld.long 0x0 20. "EDREQ_20,Enable asynchronous DMA request in stop mode for channel 20." "0: Disable asynchronous DMA request for channel 20,1: Enable asynchronous DMA request for channel 20" newline bitfld.long 0x0 19. "EDREQ_19,Enable asynchronous DMA request in stop mode for channel 19." "0: Disable asynchronous DMA request for channel 19,1: Enable asynchronous DMA request for channel 19" bitfld.long 0x0 18. "EDREQ_18,Enable asynchronous DMA request in stop mode for channel 18." "0: Disable asynchronous DMA request for channel 18,1: Enable asynchronous DMA request for channel 18" newline bitfld.long 0x0 17. "EDREQ_17,Enable asynchronous DMA request in stop mode for channel 17." "0: Disable asynchronous DMA request for channel 17,1: Enable asynchronous DMA request for channel 17" bitfld.long 0x0 16. "EDREQ_16,Enable asynchronous DMA request in stop mode for channel 16." "0: Disable asynchronous DMA request for channel 16,1: Enable asynchronous DMA request for channel 16" newline bitfld.long 0x0 15. "EDREQ_15,Enable asynchronous DMA request in stop mode for channel 15." "0: Disable asynchronous DMA request for channel 15,1: Enable asynchronous DMA request for channel 15" bitfld.long 0x0 14. "EDREQ_14,Enable asynchronous DMA request in stop mode for channel 14." "0: Disable asynchronous DMA request for channel 14,1: Enable asynchronous DMA request for channel 14" newline bitfld.long 0x0 13. "EDREQ_13,Enable asynchronous DMA request in stop mode for channel 13." "0: Disable asynchronous DMA request for channel 13,1: Enable asynchronous DMA request for channel 13" bitfld.long 0x0 12. "EDREQ_12,Enable asynchronous DMA request in stop mode for channel 12." "0: Disable asynchronous DMA request for channel 12,1: Enable asynchronous DMA request for channel 12" newline bitfld.long 0x0 11. "EDREQ_11,Enable asynchronous DMA request in stop mode for channel 11." "0: Disable asynchronous DMA request for channel 11,1: Enable asynchronous DMA request for channel 11" bitfld.long 0x0 10. "EDREQ_10,Enable asynchronous DMA request in stop mode for channel 10." "0: Disable asynchronous DMA request for channel 10,1: Enable asynchronous DMA request for channel 10" newline bitfld.long 0x0 9. "EDREQ_9,Enable asynchronous DMA request in stop mode for channel 9." "0: Disable asynchronous DMA request for channel 9,1: Enable asynchronous DMA request for channel 9" bitfld.long 0x0 8. "EDREQ_8,Enable asynchronous DMA request in stop mode for channel 8." "0: Disable asynchronous DMA request for channel 8,1: Enable asynchronous DMA request for channel 8" newline bitfld.long 0x0 7. "EDREQ_7,Enable asynchronous DMA request in stop mode for channel 7." "0: Disable asynchronous DMA request for channel 7,1: Enable asynchronous DMA request for channel 7" bitfld.long 0x0 6. "EDREQ_6,Enable asynchronous DMA request in stop mode for channel 6." "0: Disable asynchronous DMA request for channel 6,1: Enable asynchronous DMA request for channel 6" newline bitfld.long 0x0 5. "EDREQ_5,Enable asynchronous DMA request in stop mode for channel 5." "0: Disable asynchronous DMA request for channel 5,1: Enable asynchronous DMA request for channel 5" bitfld.long 0x0 4. "EDREQ_4,Enable asynchronous DMA request in stop mode for channel 4." "0: Disable asynchronous DMA request for channel 4,1: Enable asynchronous DMA request for channel 4" newline bitfld.long 0x0 3. "EDREQ_3,Enable asynchronous DMA request in stop mode for channel 3." "0: Disable asynchronous DMA request for channel 3,1: Enable asynchronous DMA request for channel 3" bitfld.long 0x0 2. "EDREQ_2,Enable asynchronous DMA request in stop mode for channel 2." "0: Disable asynchronous DMA request for channel 2,1: Enable asynchronous DMA request for channel 2" newline bitfld.long 0x0 1. "EDREQ_1,Enable asynchronous DMA request in stop mode for channel 1." "0: Disable asynchronous DMA request for channel 1,1: Enable asynchronous DMA request for channel 1" bitfld.long 0x0 0. "EDREQ_0,Enable asynchronous DMA request in stop mode for channel 0." "0: Disable asynchronous DMA request for channel 0,1: Enable asynchronous DMA request for channel 0" group.byte 0x100++0x1F line.byte 0x0 "DCHPRI3,Channel Priority" bitfld.byte 0x0 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x0 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x0 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x0 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1 "DCHPRI2,Channel Priority" bitfld.byte 0x1 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x2 "DCHPRI1,Channel Priority" bitfld.byte 0x2 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x2 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x2 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x2 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x3 "DCHPRI0,Channel Priority" bitfld.byte 0x3 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x3 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x3 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x3 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x4 "DCHPRI7,Channel Priority" bitfld.byte 0x4 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x4 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x4 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x4 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x5 "DCHPRI6,Channel Priority" bitfld.byte 0x5 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x5 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x5 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x5 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x6 "DCHPRI5,Channel Priority" bitfld.byte 0x6 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x6 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x6 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x6 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x7 "DCHPRI4,Channel Priority" bitfld.byte 0x7 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x7 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x7 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x7 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x8 "DCHPRI11,Channel Priority" bitfld.byte 0x8 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x8 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x8 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x8 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x9 "DCHPRI10,Channel Priority" bitfld.byte 0x9 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x9 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x9 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x9 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xA "DCHPRI9,Channel Priority" bitfld.byte 0xA 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xA 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xA 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xA 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xB "DCHPRI8,Channel Priority" bitfld.byte 0xB 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xB 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xB 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xB 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xC "DCHPRI15,Channel Priority" bitfld.byte 0xC 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xC 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xC 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xC 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xD "DCHPRI14,Channel Priority" bitfld.byte 0xD 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xD 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xD 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xD 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xE "DCHPRI13,Channel Priority" bitfld.byte 0xE 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xE 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xE 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xE 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0xF "DCHPRI12,Channel Priority" bitfld.byte 0xF 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0xF 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0xF 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0xF 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x10 "DCHPRI19,Channel Priority" bitfld.byte 0x10 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x10 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x10 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x10 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x11 "DCHPRI18,Channel Priority" bitfld.byte 0x11 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x11 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x11 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x11 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x12 "DCHPRI17,Channel Priority" bitfld.byte 0x12 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x12 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x12 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x12 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x13 "DCHPRI16,Channel Priority" bitfld.byte 0x13 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x13 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x13 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x13 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x14 "DCHPRI23,Channel Priority" bitfld.byte 0x14 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x14 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x14 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x14 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x15 "DCHPRI22,Channel Priority" bitfld.byte 0x15 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x15 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x15 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x15 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x16 "DCHPRI21,Channel Priority" bitfld.byte 0x16 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x16 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x16 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x16 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x17 "DCHPRI20,Channel Priority" bitfld.byte 0x17 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x17 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x17 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x17 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x18 "DCHPRI27,Channel Priority" bitfld.byte 0x18 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x18 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x18 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x18 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x19 "DCHPRI26,Channel Priority" bitfld.byte 0x19 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x19 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x19 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x19 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1A "DCHPRI25,Channel Priority" bitfld.byte 0x1A 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1A 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1A 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1A 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1B "DCHPRI24,Channel Priority" bitfld.byte 0x1B 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1B 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1B 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1B 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1C "DCHPRI31,Channel Priority" bitfld.byte 0x1C 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1C 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1C 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1C 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1D "DCHPRI30,Channel Priority" bitfld.byte 0x1D 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1D 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1D 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1D 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1E "DCHPRI29,Channel Priority" bitfld.byte 0x1E 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1E 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1E 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1E 0.--3. 1. "CHPRI,Channel n Arbitration Priority" line.byte 0x1F "DCHPRI28,Channel Priority" bitfld.byte 0x1F 7. "ECP,Enable Channel Preemption. This field resets to 0." "0: Channel n cannot be suspended by a higher..,1: Channel n can be temporarily suspended by the.." bitfld.byte 0x1F 6. "DPA,Disable Preempt Ability. This field resets to 0." "0: Channel n can suspend a lower priority channel,1: Channel n cannot suspend any channel regardless.." newline rbitfld.byte 0x1F 4.--5. "GRPPRI,Channel n Current Group Priority" "0,1,2,3" hexmask.byte 0x1F 0.--3. 1. "CHPRI,Channel n Arbitration Priority" group.long 0x1000++0x3 line.long 0x0 "TCD0_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1004++0x3 line.word 0x0 "TCD0_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD0_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0x3 line.long 0x0 "TCD0_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1008++0xB line.long 0x0 "TCD0_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD0_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD0_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1014++0x3 line.word 0x0 "TCD0_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD0_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1016++0x1 line.word 0x0 "TCD0_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1018++0x3 line.long 0x0 "TCD0_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x101C++0x3 line.word 0x0 "TCD0_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD0_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x101E++0x1 line.word 0x0 "TCD0_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1020++0x3 line.long 0x0 "TCD1_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1024++0x3 line.word 0x0 "TCD1_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD1_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0x3 line.long 0x0 "TCD1_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1028++0xB line.long 0x0 "TCD1_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD1_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD1_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1034++0x3 line.word 0x0 "TCD1_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD1_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1036++0x1 line.word 0x0 "TCD1_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1038++0x3 line.long 0x0 "TCD1_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x103C++0x3 line.word 0x0 "TCD1_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD1_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x103E++0x1 line.word 0x0 "TCD1_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1040++0x3 line.long 0x0 "TCD2_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1044++0x3 line.word 0x0 "TCD2_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD2_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0x3 line.long 0x0 "TCD2_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1048++0xB line.long 0x0 "TCD2_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD2_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD2_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1054++0x3 line.word 0x0 "TCD2_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD2_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1056++0x1 line.word 0x0 "TCD2_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1058++0x3 line.long 0x0 "TCD2_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x105C++0x3 line.word 0x0 "TCD2_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD2_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x105E++0x1 line.word 0x0 "TCD2_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1060++0x3 line.long 0x0 "TCD3_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1064++0x3 line.word 0x0 "TCD3_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD3_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0x3 line.long 0x0 "TCD3_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1068++0xB line.long 0x0 "TCD3_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD3_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD3_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1074++0x3 line.word 0x0 "TCD3_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD3_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1076++0x1 line.word 0x0 "TCD3_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1078++0x3 line.long 0x0 "TCD3_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x107C++0x3 line.word 0x0 "TCD3_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD3_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x107E++0x1 line.word 0x0 "TCD3_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1080++0x3 line.long 0x0 "TCD4_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1084++0x3 line.word 0x0 "TCD4_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD4_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0x3 line.long 0x0 "TCD4_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1088++0xB line.long 0x0 "TCD4_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD4_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD4_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1094++0x3 line.word 0x0 "TCD4_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD4_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1096++0x1 line.word 0x0 "TCD4_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1098++0x3 line.long 0x0 "TCD4_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x109C++0x3 line.word 0x0 "TCD4_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD4_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x109E++0x1 line.word 0x0 "TCD4_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10A0++0x3 line.long 0x0 "TCD5_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10A4++0x3 line.word 0x0 "TCD5_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD5_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0x3 line.long 0x0 "TCD5_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10A8++0xB line.long 0x0 "TCD5_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD5_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD5_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10B4++0x3 line.word 0x0 "TCD5_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD5_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10B6++0x1 line.word 0x0 "TCD5_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10B8++0x3 line.long 0x0 "TCD5_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10BC++0x3 line.word 0x0 "TCD5_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD5_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10BE++0x1 line.word 0x0 "TCD5_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10C0++0x3 line.long 0x0 "TCD6_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10C4++0x3 line.word 0x0 "TCD6_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD6_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0x3 line.long 0x0 "TCD6_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10C8++0xB line.long 0x0 "TCD6_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD6_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD6_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10D4++0x3 line.word 0x0 "TCD6_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD6_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10D6++0x1 line.word 0x0 "TCD6_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10D8++0x3 line.long 0x0 "TCD6_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10DC++0x3 line.word 0x0 "TCD6_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD6_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10DE++0x1 line.word 0x0 "TCD6_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x10E0++0x3 line.long 0x0 "TCD7_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x10E4++0x3 line.word 0x0 "TCD7_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD7_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0x3 line.long 0x0 "TCD7_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x10E8++0xB line.long 0x0 "TCD7_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD7_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD7_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x10F4++0x3 line.word 0x0 "TCD7_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD7_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x10F6++0x1 line.word 0x0 "TCD7_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x10F8++0x3 line.long 0x0 "TCD7_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x10FC++0x3 line.word 0x0 "TCD7_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD7_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x10FE++0x1 line.word 0x0 "TCD7_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1100++0x3 line.long 0x0 "TCD8_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1104++0x3 line.word 0x0 "TCD8_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD8_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0x3 line.long 0x0 "TCD8_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1108++0xB line.long 0x0 "TCD8_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD8_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD8_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1114++0x3 line.word 0x0 "TCD8_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD8_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1116++0x1 line.word 0x0 "TCD8_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1118++0x3 line.long 0x0 "TCD8_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x111C++0x3 line.word 0x0 "TCD8_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD8_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x111E++0x1 line.word 0x0 "TCD8_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1120++0x3 line.long 0x0 "TCD9_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1124++0x3 line.word 0x0 "TCD9_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD9_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0x3 line.long 0x0 "TCD9_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1128++0xB line.long 0x0 "TCD9_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD9_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD9_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1134++0x3 line.word 0x0 "TCD9_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD9_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1136++0x1 line.word 0x0 "TCD9_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1138++0x3 line.long 0x0 "TCD9_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x113C++0x3 line.word 0x0 "TCD9_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD9_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x113E++0x1 line.word 0x0 "TCD9_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1140++0x3 line.long 0x0 "TCD10_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1144++0x3 line.word 0x0 "TCD10_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD10_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0x3 line.long 0x0 "TCD10_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1148++0xB line.long 0x0 "TCD10_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD10_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD10_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1154++0x3 line.word 0x0 "TCD10_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD10_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1156++0x1 line.word 0x0 "TCD10_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1158++0x3 line.long 0x0 "TCD10_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x115C++0x3 line.word 0x0 "TCD10_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD10_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x115E++0x1 line.word 0x0 "TCD10_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1160++0x3 line.long 0x0 "TCD11_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1164++0x3 line.word 0x0 "TCD11_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD11_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0x3 line.long 0x0 "TCD11_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1168++0xB line.long 0x0 "TCD11_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD11_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD11_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1174++0x3 line.word 0x0 "TCD11_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD11_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1176++0x1 line.word 0x0 "TCD11_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1178++0x3 line.long 0x0 "TCD11_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x117C++0x3 line.word 0x0 "TCD11_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD11_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x117E++0x1 line.word 0x0 "TCD11_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1180++0x3 line.long 0x0 "TCD12_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1184++0x3 line.word 0x0 "TCD12_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD12_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0x3 line.long 0x0 "TCD12_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1188++0xB line.long 0x0 "TCD12_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD12_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD12_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1194++0x3 line.word 0x0 "TCD12_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD12_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1196++0x1 line.word 0x0 "TCD12_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1198++0x3 line.long 0x0 "TCD12_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x119C++0x3 line.word 0x0 "TCD12_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD12_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x119E++0x1 line.word 0x0 "TCD12_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11A0++0x3 line.long 0x0 "TCD13_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11A4++0x3 line.word 0x0 "TCD13_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD13_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0x3 line.long 0x0 "TCD13_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11A8++0xB line.long 0x0 "TCD13_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD13_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD13_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11B4++0x3 line.word 0x0 "TCD13_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD13_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11B6++0x1 line.word 0x0 "TCD13_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11B8++0x3 line.long 0x0 "TCD13_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11BC++0x3 line.word 0x0 "TCD13_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD13_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11BE++0x1 line.word 0x0 "TCD13_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11C0++0x3 line.long 0x0 "TCD14_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11C4++0x3 line.word 0x0 "TCD14_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD14_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0x3 line.long 0x0 "TCD14_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11C8++0xB line.long 0x0 "TCD14_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD14_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD14_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11D4++0x3 line.word 0x0 "TCD14_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD14_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11D6++0x1 line.word 0x0 "TCD14_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11D8++0x3 line.long 0x0 "TCD14_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11DC++0x3 line.word 0x0 "TCD14_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD14_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11DE++0x1 line.word 0x0 "TCD14_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x11E0++0x3 line.long 0x0 "TCD15_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x11E4++0x3 line.word 0x0 "TCD15_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD15_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0x3 line.long 0x0 "TCD15_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x11E8++0xB line.long 0x0 "TCD15_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD15_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD15_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x11F4++0x3 line.word 0x0 "TCD15_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD15_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x11F6++0x1 line.word 0x0 "TCD15_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x11F8++0x3 line.long 0x0 "TCD15_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x11FC++0x3 line.word 0x0 "TCD15_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD15_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x11FE++0x1 line.word 0x0 "TCD15_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1200++0x3 line.long 0x0 "TCD16_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1204++0x3 line.word 0x0 "TCD16_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD16_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0x3 line.long 0x0 "TCD16_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1208++0xB line.long 0x0 "TCD16_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD16_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD16_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1214++0x3 line.word 0x0 "TCD16_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD16_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1216++0x1 line.word 0x0 "TCD16_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1218++0x3 line.long 0x0 "TCD16_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x121C++0x3 line.word 0x0 "TCD16_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD16_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x121E++0x1 line.word 0x0 "TCD16_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1220++0x3 line.long 0x0 "TCD17_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1224++0x3 line.word 0x0 "TCD17_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD17_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0x3 line.long 0x0 "TCD17_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1228++0xB line.long 0x0 "TCD17_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD17_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD17_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1234++0x3 line.word 0x0 "TCD17_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD17_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1236++0x1 line.word 0x0 "TCD17_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1238++0x3 line.long 0x0 "TCD17_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x123C++0x3 line.word 0x0 "TCD17_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD17_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x123E++0x1 line.word 0x0 "TCD17_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1240++0x3 line.long 0x0 "TCD18_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1244++0x3 line.word 0x0 "TCD18_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD18_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0x3 line.long 0x0 "TCD18_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1248++0xB line.long 0x0 "TCD18_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD18_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD18_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1254++0x3 line.word 0x0 "TCD18_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD18_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1256++0x1 line.word 0x0 "TCD18_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1258++0x3 line.long 0x0 "TCD18_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x125C++0x3 line.word 0x0 "TCD18_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD18_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x125E++0x1 line.word 0x0 "TCD18_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1260++0x3 line.long 0x0 "TCD19_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1264++0x3 line.word 0x0 "TCD19_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD19_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0x3 line.long 0x0 "TCD19_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1268++0xB line.long 0x0 "TCD19_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD19_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD19_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1274++0x3 line.word 0x0 "TCD19_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD19_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1276++0x1 line.word 0x0 "TCD19_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1278++0x3 line.long 0x0 "TCD19_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x127C++0x3 line.word 0x0 "TCD19_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD19_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x127E++0x1 line.word 0x0 "TCD19_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1280++0x3 line.long 0x0 "TCD20_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1284++0x3 line.word 0x0 "TCD20_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD20_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0x3 line.long 0x0 "TCD20_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1288++0xB line.long 0x0 "TCD20_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD20_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD20_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1294++0x3 line.word 0x0 "TCD20_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD20_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1296++0x1 line.word 0x0 "TCD20_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1298++0x3 line.long 0x0 "TCD20_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x129C++0x3 line.word 0x0 "TCD20_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD20_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x129E++0x1 line.word 0x0 "TCD20_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12A0++0x3 line.long 0x0 "TCD21_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12A4++0x3 line.word 0x0 "TCD21_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD21_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0x3 line.long 0x0 "TCD21_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12A8++0xB line.long 0x0 "TCD21_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD21_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD21_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12B4++0x3 line.word 0x0 "TCD21_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD21_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12B6++0x1 line.word 0x0 "TCD21_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12B8++0x3 line.long 0x0 "TCD21_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12BC++0x3 line.word 0x0 "TCD21_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD21_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12BE++0x1 line.word 0x0 "TCD21_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12C0++0x3 line.long 0x0 "TCD22_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12C4++0x3 line.word 0x0 "TCD22_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD22_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0x3 line.long 0x0 "TCD22_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12C8++0xB line.long 0x0 "TCD22_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD22_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD22_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12D4++0x3 line.word 0x0 "TCD22_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD22_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12D6++0x1 line.word 0x0 "TCD22_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12D8++0x3 line.long 0x0 "TCD22_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12DC++0x3 line.word 0x0 "TCD22_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD22_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12DE++0x1 line.word 0x0 "TCD22_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x12E0++0x3 line.long 0x0 "TCD23_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x12E4++0x3 line.word 0x0 "TCD23_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD23_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0x3 line.long 0x0 "TCD23_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x12E8++0xB line.long 0x0 "TCD23_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD23_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD23_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x12F4++0x3 line.word 0x0 "TCD23_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD23_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x12F6++0x1 line.word 0x0 "TCD23_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x12F8++0x3 line.long 0x0 "TCD23_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x12FC++0x3 line.word 0x0 "TCD23_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD23_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x12FE++0x1 line.word 0x0 "TCD23_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1300++0x3 line.long 0x0 "TCD24_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1304++0x3 line.word 0x0 "TCD24_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD24_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0x3 line.long 0x0 "TCD24_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1308++0xB line.long 0x0 "TCD24_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD24_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD24_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1314++0x3 line.word 0x0 "TCD24_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD24_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1316++0x1 line.word 0x0 "TCD24_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1318++0x3 line.long 0x0 "TCD24_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x131C++0x3 line.word 0x0 "TCD24_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD24_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x131E++0x1 line.word 0x0 "TCD24_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1320++0x3 line.long 0x0 "TCD25_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1324++0x3 line.word 0x0 "TCD25_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD25_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0x3 line.long 0x0 "TCD25_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1328++0xB line.long 0x0 "TCD25_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD25_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD25_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1334++0x3 line.word 0x0 "TCD25_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD25_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1336++0x1 line.word 0x0 "TCD25_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1338++0x3 line.long 0x0 "TCD25_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x133C++0x3 line.word 0x0 "TCD25_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD25_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x133E++0x1 line.word 0x0 "TCD25_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1340++0x3 line.long 0x0 "TCD26_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1344++0x3 line.word 0x0 "TCD26_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD26_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0x3 line.long 0x0 "TCD26_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1348++0xB line.long 0x0 "TCD26_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD26_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD26_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1354++0x3 line.word 0x0 "TCD26_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD26_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1356++0x1 line.word 0x0 "TCD26_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1358++0x3 line.long 0x0 "TCD26_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x135C++0x3 line.word 0x0 "TCD26_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD26_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x135E++0x1 line.word 0x0 "TCD26_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1360++0x3 line.long 0x0 "TCD27_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1364++0x3 line.word 0x0 "TCD27_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD27_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0x3 line.long 0x0 "TCD27_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1368++0xB line.long 0x0 "TCD27_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD27_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD27_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1374++0x3 line.word 0x0 "TCD27_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD27_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1376++0x1 line.word 0x0 "TCD27_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1378++0x3 line.long 0x0 "TCD27_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x137C++0x3 line.word 0x0 "TCD27_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD27_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x137E++0x1 line.word 0x0 "TCD27_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x1380++0x3 line.long 0x0 "TCD28_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x1384++0x3 line.word 0x0 "TCD28_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD28_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0x3 line.long 0x0 "TCD28_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x1388++0xB line.long 0x0 "TCD28_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD28_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD28_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x1394++0x3 line.word 0x0 "TCD28_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD28_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x1396++0x1 line.word 0x0 "TCD28_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x1398++0x3 line.long 0x0 "TCD28_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x139C++0x3 line.word 0x0 "TCD28_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD28_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x139E++0x1 line.word 0x0 "TCD28_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13A0++0x3 line.long 0x0 "TCD29_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13A4++0x3 line.word 0x0 "TCD29_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD29_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0x3 line.long 0x0 "TCD29_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13A8++0xB line.long 0x0 "TCD29_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD29_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD29_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13B4++0x3 line.word 0x0 "TCD29_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD29_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13B6++0x1 line.word 0x0 "TCD29_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13B8++0x3 line.long 0x0 "TCD29_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13BC++0x3 line.word 0x0 "TCD29_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD29_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13BE++0x1 line.word 0x0 "TCD29_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13C0++0x3 line.long 0x0 "TCD30_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13C4++0x3 line.word 0x0 "TCD30_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD30_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0x3 line.long 0x0 "TCD30_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13C8++0xB line.long 0x0 "TCD30_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD30_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD30_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13D4++0x3 line.word 0x0 "TCD30_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD30_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13D6++0x1 line.word 0x0 "TCD30_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13D8++0x3 line.long 0x0 "TCD30_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13DC++0x3 line.word 0x0 "TCD30_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD30_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13DE++0x1 line.word 0x0 "TCD30_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" group.long 0x13E0++0x3 line.long 0x0 "TCD31_SADDR,TCD Source Address" hexmask.long 0x0 0.--31. 1. "SADDR,Source Address" group.word 0x13E4++0x3 line.word 0x0 "TCD31_SOFF,TCD Signed Source Address Offset" hexmask.word 0x0 0.--15. 1. "SOFF,Source address signed offset" line.word 0x2 "TCD31_ATTR,TCD Transfer Attributes" hexmask.word.byte 0x2 11.--15. 1. "SMOD,Source Address Modulo" bitfld.word 0x2 8.--10. "SSIZE,Source data transfer size" "0: 8-bit,1: 16-bit,2: 32-bit,3: 64-bit,?,5: 32-byte burst (4 beats of 64 bits),?,?" newline hexmask.word.byte 0x2 3.--7. 1. "DMOD,Destination Address Modulo" bitfld.word 0x2 0.--2. "DSIZE,Destination data transfer size" "0,1,2,3,4,5,6,7" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLNO,TCD Minor Byte Count (Minor Loop Mapping Disabled)" hexmask.long 0x0 0.--31. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0x3 line.long 0x0 "TCD31_NBYTES_MLOFFNO,TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long 0x0 0.--29. 1. "NBYTES,Minor Byte Transfer Count" group.long 0x13E8++0xB line.long 0x0 "TCD31_NBYTES_MLOFFYES,TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled)" bitfld.long 0x0 31. "SMLOE,Source Minor Loop Offset Enable" "0: The minor loop offset is not applied to the SADDR,1: The minor loop offset is applied to the SADDR" bitfld.long 0x0 30. "DMLOE,Destination Minor Loop Offset Enable" "0: The minor loop offset is not applied to the DADDR,1: The minor loop offset is applied to the DADDR" newline hexmask.long.tbyte 0x0 10.--29. 1. "MLOFF,If SMLOE = 1 or DMLOE = 1 this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes." hexmask.long.word 0x0 0.--9. 1. "NBYTES,Minor Byte Transfer Count" line.long 0x4 "TCD31_SLAST,TCD Last Source Address Adjustment" hexmask.long 0x4 0.--31. 1. "SLAST,Last Source Address Adjustment" line.long 0x8 "TCD31_DADDR,TCD Destination Address" hexmask.long 0x8 0.--31. 1. "DADDR,Destination Address" group.word 0x13F4++0x3 line.word 0x0 "TCD31_DOFF,TCD Signed Destination Address Offset" hexmask.word 0x0 0.--15. 1. "DOFF,Destination Address Signed Offset" line.word 0x2 "TCD31_CITER_ELINKNO,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "CITER,Current Major Iteration Count" group.word 0x13F6++0x1 line.word 0x0 "TCD31_CITER_ELINKYES,TCD Current Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enable channel-to-channel linking on minor-loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Minor Loop Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "CITER,Current Major Iteration Count" group.long 0x13F8++0x3 line.long 0x0 "TCD31_DLASTSGA,TCD Last Destination Address Adjustment/Scatter Gather Address" hexmask.long 0x0 0.--31. 1. "DLASTSGA,Destination last address adjustment or next memory address TCD for channel (scatter/gather)" group.word 0x13FC++0x3 line.word 0x0 "TCD31_CSR,TCD Control and Status" bitfld.word 0x0 14.--15. "BWC,Bandwidth Control" "0: No eDMA engine stalls,?,2: eDMA engine stalls for 4 cycles after each R/W,3: eDMA engine stalls for 8 cycles after each R/W" hexmask.word.byte 0x0 8.--12. 1. "MAJORLINKCH,Major Loop Link Channel Number" newline bitfld.word 0x0 7. "DONE,Channel Done" "0,1" rbitfld.word 0x0 6. "ACTIVE,Channel Active" "0,1" newline bitfld.word 0x0 5. "MAJORELINK,Enable channel-to-channel linking on major loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" bitfld.word 0x0 4. "ESG,Enable Scatter/Gather Processing" "0: The current channel's TCD is normal format,1: The current channel's TCD specifies a scatter.." newline bitfld.word 0x0 3. "DREQ,Disable Request" "0: The channel's ERQ field is not affected,1: The channel's ERQ field value changes to 0 when.." bitfld.word 0x0 2. "INTHALF,Enable an interrupt when major counter is half complete." "0: Half-point interrupt is disabled,1: Half-point interrupt is enabled" newline bitfld.word 0x0 1. "INTMAJOR,Enable an interrupt when major iteration count completes." "0: End of major loop interrupt is disabled,1: End of major loop interrupt is enabled" bitfld.word 0x0 0. "START,Channel Start" "0: Channel is not explicitly started,1: Channel is explicitly started via a software.." line.word 0x2 "TCD31_BITER_ELINKNO,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Disabled)" bitfld.word 0x2 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word 0x2 0.--14. 1. "BITER,Starting Major Iteration Count" group.word 0x13FE++0x1 line.word 0x0 "TCD31_BITER_ELINKYES,TCD Beginning Minor Loop Link. Major Loop Count (Channel Linking Enabled)" bitfld.word 0x0 15. "ELINK,Enables channel-to-channel linking on minor loop complete" "0: Channel-to-channel linking is disabled,1: Channel-to-channel linking is enabled" hexmask.word.byte 0x0 9.--13. 1. "LINKCH,Link Channel Number" newline hexmask.word 0x0 0.--8. 1. "BITER,Starting major iteration count" tree.end endif tree.end tree "DMAMUX" base ad:0x0 sif (cpuis("IMXRT1163-CM7")||cpuis("IMXRT1165-CM7")) tree "DMAMUX0" base ad:0x40074000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CHCFG[$1],Channel index Configuration Register" bitfld.long 0x0 31. "ENBL,DMA Mux Channel Enable" "0: DMA Mux channel is disabled,1: DMA Mux channel is enabled" bitfld.long 0x0 30. "TRIG,DMA Channel Trigger Enable" "0: Triggering is disabled. If triggering is..,1: Triggering is enabled. If triggering is enabled.." newline bitfld.long 0x0 29. "A_ON,DMA Channel Always Enable" "0: DMA Channel Always ON function is disabled,1: DMA Channel Always ON function is enabled" hexmask.long.byte 0x0 0.--7. 1. "SOURCE,DMA Channel Source (Slot Number)" repeat.end tree.end endif sif (cpuis("IMXRT1165-CM4")) tree "DMAMUX1" base ad:0x40C18000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CHCFG[$1],Channel index Configuration Register" bitfld.long 0x0 31. "ENBL,DMA Mux Channel Enable" "0: DMA Mux channel is disabled,1: DMA Mux channel is enabled" bitfld.long 0x0 30. "TRIG,DMA Channel Trigger Enable" "0: Triggering is disabled. If triggering is..,1: Triggering is enabled. If triggering is enabled.." newline bitfld.long 0x0 29. "A_ON,DMA Channel Always Enable" "0: DMA Channel Always ON function is disabled,1: DMA Channel Always ON function is enabled" hexmask.long.byte 0x0 0.--7. 1. "SOURCE,DMA Channel Source (Slot Number)" repeat.end tree.end endif sif (cpuis("IMXRT1166-CM4")) tree "DMAMUX1" base ad:0x40C18000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CHCFG[$1],Channel index Configuration Register" bitfld.long 0x0 31. "ENBL,DMA Mux Channel Enable" "0: DMA Mux channel is disabled,1: DMA Mux channel is enabled" bitfld.long 0x0 30. "TRIG,DMA Channel Trigger Enable" "0: Triggering is disabled. If triggering is..,1: Triggering is enabled. If triggering is enabled.." newline bitfld.long 0x0 29. "A_ON,DMA Channel Always Enable" "0: DMA Channel Always ON function is disabled,1: DMA Channel Always ON function is enabled" hexmask.long.byte 0x0 0.--7. 1. "SOURCE,DMA Channel Source (Slot Number)" repeat.end tree.end endif sif (cpuis("IMXRT1166-CM7")) tree "DMAMUX0" base ad:0x40074000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CHCFG[$1],Channel index Configuration Register" bitfld.long 0x0 31. "ENBL,DMA Mux Channel Enable" "0: DMA Mux channel is disabled,1: DMA Mux channel is enabled" bitfld.long 0x0 30. "TRIG,DMA Channel Trigger Enable" "0: Triggering is disabled. If triggering is..,1: Triggering is enabled. If triggering is enabled.." newline bitfld.long 0x0 29. "A_ON,DMA Channel Always Enable" "0: DMA Channel Always ON function is disabled,1: DMA Channel Always ON function is enabled" hexmask.long.byte 0x0 0.--7. 1. "SOURCE,DMA Channel Source (Slot Number)" repeat.end tree.end endif tree.end tree "DSI_HOST" base ad:0x0 tree "DSI_HOST" base ad:0x4080C000 group.long 0x0++0x2B line.long 0x0 "CFG_NUM_LANES,CFG_NUM_LANES" bitfld.long 0x0 0.--1. "NUM_LANES,Sets the number of active lanes that are to be used for transmitting data." "0: 1 lane,1: 2 lanes,?,?" line.long 0x4 "CFG_NONCONTINUOUS_CLK,CFG_NONCONTINUOUS_CLK" bitfld.long 0x4 0. "CLK_MODE,Sets the Host Controller into non-continuous MIPI clock mode. When in non-continuous clock mode the high speed clock will transition into low power mode between transmissions." "0: Continuous high speed clock,1: Non-Continuous high speed clock" line.long 0x8 "CFG_T_PRE,CFG_T_PRE" hexmask.long.byte 0x8 0.--7. 1. "NUM_PERIODS,Sets the number of byte clock periods ('clk_byte' input) that the controller will wait after enabling the clock lane for HS operation before enabling the data lanes for HS operation. This setting represents the TCLK-PRE DPHY timing parameter." line.long 0xC "CFG_T_POST,CFG_T_POST" hexmask.long.byte 0xC 0.--7. 1. "NUM_PERIODS,Sets the number of byte clock periods ('clk_byte' input) to wait before putting the clock lane into LP mode after the data lanes have been detected to be in Stop State. This setting represents the DPHY timing parameters TLPX + TCLK-PREPARE +.." line.long 0x10 "CFG_TX_GAP,CFG_TX_GAP" hexmask.long.byte 0x10 0.--7. 1. "NUM_PERIODS,Sets the number of byte clock periods ('clk_byte' input) that the controller will wait after the clock lane has been put into LP mode before enabling the clock lane for HS mode again. This setting represents the THS-EXIT DPHY timing.." line.long 0x14 "CFG_AUTOINSERT_EOTP,CFG_AUTOINSERT_ETOP" bitfld.long 0x14 0. "AUTOINSERT,Enables the Host Controller to automatically insert an EoTp short packet when switching from HS to LP mode." "0: EoTp is not automatically inserted,1: EoTp is automatically inserted" line.long 0x18 "CFG_EXTRA_CMDS_AFTER_EOTP,CFG_EXTRA_CMDS_AFTER_ETOP" hexmask.long.byte 0x18 0.--7. 1. "EXTRA_EOTP,Configures the DSI Host Controller to send extra End Of Transmission Packets after the end of a packet. The value is the number of extra EOTP packets sent." line.long 0x1C "CFG_HTX_TO_COUNT,CFG_HTX_TO_COUNT" hexmask.long.tbyte 0x1C 0.--23. 1. "COUNT,Sets the value of the DSI Host High Speed TX timeout count in clk_byte clock periods that once reached will initiate a timeout error and follow the recovery procedure documented in the DSI specification." line.long 0x20 "CFG_LRX_H_TO_COUNT,CFG_LRX_H_TO_COUNT" hexmask.long.tbyte 0x20 0.--23. 1. "COUNT,Sets the value of the DSI Host low power RX timeout count in clk_byte clock periods that once reached will initiate a timeout error and follow the recovery procedure documented in the DSI specification." line.long 0x24 "CFG_BTA_H_TO_COUNT,CFG_BTA_H_TO_COUNT" hexmask.long.tbyte 0x24 0.--23. 1. "COUNT,Sets the value of the DSI Host Bus Turn Around (BTA) timeout in clk_byte clock periods that once reached will initiate a timeout error." line.long 0x28 "CFG_TWAKEUP,CFG_TWAKEUP" hexmask.long.tbyte 0x28 0.--18. 1. "NUM_PERIODS,DPHY Twakeup timing parameter. Sets the number of clk_esc clock periods to keep a clock or data lane in Mark-1 state after exiting ULPS. The MIPI DPHY spec requires a minimum of 1ms in Mark-1 state after leaving ULPS." rgroup.long 0x2C++0x7 line.long 0x0 "CFG_STATUS_OUT,CFG_STATUS_OUT" hexmask.long 0x0 0.--31. 1. "STATUS,Status Register" line.long 0x4 "RX_ERROR_STATUS,RX_ERROR_STATUS" hexmask.long.word 0x4 0.--10. 1. "STATUS,Status Register for Host receive error detection ECC errors CRC errors and for timeout indicators" tree.end tree "DSI_HOST_APB_PKT_IF" base ad:0x4080C280 group.long 0x0++0xB line.long 0x0 "TX_PAYLOAD,TX_PAYLOAD" hexmask.long 0x0 0.--31. 1. "PAYLOAD,Tx Payload data write register. Write to this register loads the payload FIFO with 32 bit values." line.long 0x4 "PKT_CONTROL,PKT_CONTROL" hexmask.long 0x4 0.--26. 1. "CTRL,Tx packet control" line.long 0x8 "SEND_PACKET,SEND_PACKET" bitfld.long 0x8 0. "TX_SEND,Tx send packet writing to this register causes the packet described in dsi_host_pkt_control to be sent." "0: Packet not sent,1: Packet is sent" rgroup.long 0xC++0x1B line.long 0x0 "PKT_STATUS,PKT_STATUS" hexmask.long.word 0x0 0.--8. 1. "STATUS,Status of APB to packet interface." line.long 0x4 "PKT_FIFO_WR_LEVEL,PKT_FIFO_WR_LEVEL" hexmask.long.word 0x4 0.--15. 1. "WR,Write level of APB to pkt interface FIFO" line.long 0x8 "PKT_FIFO_RD_LEVEL,PKT_FIFO_RD_LEVEL" hexmask.long.word 0x8 0.--15. 1. "RD,Read level of APB to pkt interface FIFO" line.long 0xC "PKT_RX_PAYLOAD,PKT_RX_PAYLOAD" hexmask.long 0xC 0.--31. 1. "PAYLOAD,APB to pkt interface Rx payload read" line.long 0x10 "PKT_RX_PKT_HEADER,PKT_RX_PKT_HEADER" hexmask.long.tbyte 0x10 0.--23. 1. "HEADER,APB to pkt interface Rx packet header" line.long 0x14 "IRQ_STATUS,IRQ_STATUS" hexmask.long 0x14 0.--31. 1. "STATUS,Status of APB to packet interface." line.long 0x18 "IRQ_STATUS2,IRQ_STATUS2" bitfld.long 0x18 0.--2. "STATUS2,Status of APB to packet interface part 2 read part 2 first then dsi_host_irq_status. Reading dsi_host_irq_status will clear both status and status2." "0,1,2,3,4,5,6,7" group.long 0x28++0x7 line.long 0x0 "IRQ_MASK,IRQ_MASK" hexmask.long 0x0 0.--31. 1. "MASK,IRQ Mask" line.long 0x4 "IRQ_MASK2,IRQ_MASK2" bitfld.long 0x4 0.--2. "MASK2,IRQ mask 2" "0,1,2,3,4,5,6,7" tree.end tree "DSI_HOST_DPHY_INTFC" base ad:0x4080C300 group.long 0x0++0x2F line.long 0x0 "PD_TX,PD_TX" bitfld.long 0x0 0. "PD_TX,Power Down input for D-PHY" "0: Power Up,1: Power Down" line.long 0x4 "M_PRG_HS_PREPARE,M_PRG_HS_PREPARE" bitfld.long 0x4 0.--1. "M_PRG_HS_PREPARE,DPHY m_PRG_HS_PREPARE input" "0,1,2,3" line.long 0x8 "MC_PRG_HS_PREPARE,MC_PRG_HS_PREPARE" bitfld.long 0x8 0. "MC_PRG_HS_PREPARE,DPHY mc_PRG_HS_PREPARE input" "0,1" line.long 0xC "M_PRG_HS_ZERO,M_PRG_HS_ZERO" hexmask.long.byte 0xC 0.--4. 1. "M_PRG_HS_ZERO,DPHY m_PRG_HS_ZERO input" line.long 0x10 "MC_PRG_HS_ZERO,MC_PRG_HS_ZERO" hexmask.long.byte 0x10 0.--5. 1. "MC_PRG_HS_ZERO,DPHY mc_PRG_HS_ZERO input" line.long 0x14 "M_PRG_HS_TRAIL,M_PRG_HS_TRAIL" hexmask.long.byte 0x14 0.--3. 1. "M_PRG_HS_TRAIL,DPHY m_PRG_HS_TRAIL input" line.long 0x18 "MC_PRG_HS_TRAIL,MC_PRG_HS_TRAIL" hexmask.long.byte 0x18 0.--3. 1. "MC_PRG_HS_TRAIL,DPHY mc_PRG_HS_TRAIL input" line.long 0x1C "PD_PLL,PD_PLL" bitfld.long 0x1C 0. "PD_PLL,Power-down signal" "0: Power up PLL,1: Power down PLL" line.long 0x20 "TST,TST" hexmask.long.byte 0x20 0.--5. 1. "TST,Test" line.long 0x24 "CN,CN" hexmask.long.byte 0x24 0.--4. 1. "CN,Control N divider" line.long 0x28 "CM,CM" hexmask.long.byte 0x28 0.--7. 1. "CM,Control M divider" line.long 0x2C "CO,CO" bitfld.long 0x2C 0.--1. "CO,Control O divider" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8" rgroup.long 0x30++0x3 line.long 0x0 "LOCK,LOCK" bitfld.long 0x0 0. "LOCK,Lock Detect output" "0: PLL not locked,1: PLL has achieved frequency lock" group.long 0x34++0x13 line.long 0x0 "LOCK_BYP,LOCK_BYP" bitfld.long 0x0 0. "LOCK_BYP,DPHY LOCK_BYP input" "0: PLL LOCK signal will gate TxByteClkHS clock,1: PLL LOCK signal will not gate TxByteClkHS clock.." line.long 0x4 "TX_RCAL,TX_RCAL" bitfld.long 0x4 0.--1. "TX_RCAL,On-chip termination control bits for manual calibration of HS-TX" "0: 20% higher than mid-range. Highest impedance..,1: Mid-range impedance setting (default),2: 15% lower than mid-range,3: 25% lower than mid-range. Lowest impedance setting" line.long 0x8 "AUTO_PD_EN,AUTO_PD_EN" bitfld.long 0x8 0. "AUTO_PD_EN,DPHY AUTO_PD_EN input" "0: Inactive lanes are powered up and driving LP11,1: inactive lanes are powered down" line.long 0xC "RXLPRP,RXLPRP" bitfld.long 0xC 0.--1. "RXLPRP,DPHY RXLPRP input" "0,1,2,3" line.long 0x10 "RXCDRP,RXCDRP" bitfld.long 0x10 0.--1. "RXCDRP,DPHY RXCDRP input" "0: 344mV,1: 325mV (Default),2: 307mV,3: Invalid" tree.end tree "DSI_HOST_DPI_INTFC" base ad:0x4080C200 group.long 0x0++0x3F line.long 0x0 "PIXEL_PAYLOAD_SIZE,PEXEL_PAYLOAD_SIZE" hexmask.long.word 0x0 0.--15. 1. "PAYLOAD_SIZE,Maximum number of pixels that should be sent as one DSI packet. Recommended to be evenly divisible by the line size (in pixels)." line.long 0x4 "PIXEL_FIFO_SEND_LEVEL,PIXEL_FIFO_SEND_LEVEL" hexmask.long.word 0x4 0.--15. 1. "FIFO_SEND_LEVEL,In order to optimize DSI utility the DPI bridge buffers a certain number of DPI pixels before initiating a DSI packet. This configuration port controls the level at which the DPI Host bridge begins sending pixels." line.long 0x8 "INTERFACE_COLOR_CODING,INTERFACE_COLOR_CODING" bitfld.long 0x8 0.--2. "RGB_CONFIG,Sets the distribution of RGB bits within the 24-bit d bus as specified by the DPI specification." "0: 16-bit Configuration 1,1: 16-bit Configuration 2,2: 16-bit Configuration 3,3: 18-bit Configuration 1,4: 18-bit Configuration 2,5: 24-bit,?,?" line.long 0xC "PIXEL_FORMAT,PIXEL_FORMAT" bitfld.long 0xC 0.--1. "PIXEL_FORMAT,Sets the DSI packet type of the pixels" "0: 16 bit,1: 18 bit,2: 18 bit loosely packed,3: 24 bit" line.long 0x10 "VSYNC_POLARITY,VSYNC_POLARITY" bitfld.long 0x10 0. "VSYNC_POLARITY,Sets polarity of dpi_vsync_input" "0: active low,1: active high" line.long 0x14 "HSYNC_POLARITY,HSYNC_POLARITY" bitfld.long 0x14 0. "HSYNC_POLARITY,Sets polarity of dpi_hsync_input" "0: active low,1: active high" line.long 0x18 "VIDEO_MODE,VIDEO_MODE" bitfld.long 0x18 0.--1. "VIDEO_MODE,Select DSI video mode that the host DPI module should generate packets for." "0: Non-Burst mode with Sync Pulses,1: Non-Burst mode with Sync Events,2: Burst mode,?" line.long 0x1C "HFP,HFP" hexmask.long.word 0x1C 0.--15. 1. "PAYLOAD_SIZE,Sets the DSI packet payload size in bytes of the horizontal front porch blanking packet." line.long 0x20 "HBP,HBP" hexmask.long.word 0x20 0.--15. 1. "PAYLOAD_SIZE,Sets the DSI packet payload size in bytes of the horizontal back porch blanking packet." line.long 0x24 "HSA,HSA" hexmask.long.word 0x24 0.--15. 1. "PAYLOAD_SIZE,Sets the DSI packet payload size in bytes of the horizontal sync width filler blanking packet." line.long 0x28 "ENABLE_MULT_PKTS,ENABLE_MULT_PKTS" bitfld.long 0x28 0. "ENABLE_MULT_PKTS,Enable Multiple packets per video line. When enabled PIXEL_PAYLOAD_SIZE[PAYLOAD_SIZE] must be set to exactly half the size of the video line" "0: Video Line is sent in a single packet,1: Video Line is sent in two packets" line.long 0x2C "VBP,VBP" hexmask.long.byte 0x2C 0.--7. 1. "NUM_LINES,Sets the number of lines in the vertical back porch." line.long 0x30 "VFP,VFP" hexmask.long.byte 0x30 0.--7. 1. "NUM_LINES,Sets the number of lines in the vertical front porch." line.long 0x34 "BLLP_MODE,BLLP_MODE" bitfld.long 0x34 0. "LP,Optimize bllp periods to Low Power mode when possible" "0: Blanking packets are sent during BLLP periods,1: LP mode is used for BLLP periods" line.long 0x38 "USE_NULL_PKT_BLLP,USE_NULL_PKT_BLLP" bitfld.long 0x38 0. "NULL,Selects type of blanking packet to be sent during bllp" "0: Blanking packet used in bllp region 1,1: Null packet used in bllp region" line.long 0x3C "VACTIVE,VACTIVE" hexmask.long.word 0x3C 0.--13. 1. "NUM_LINES,Sets the number of lines in the vertical active aread." tree.end tree.end tree "EMVSIM" base ad:0x0 tree "EMVSIM1" base ad:0x40154000 rgroup.long 0x0++0x7 line.long 0x0 "VER_ID,Version ID Register" hexmask.long 0x0 0.--31. 1. "VER,Version ID of the module" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "TX_FIFO_DEPTH,Transmit FIFO Depth" hexmask.long.byte 0x4 0.--7. 1. "RX_FIFO_DEPTH,Receive FIFO Depth" group.long 0x8++0x23 line.long 0x0 "CLKCFG,Clock Configuration Register" bitfld.long 0x0 10.--11. "GPCNT0_CLK_SEL,General Purpose Counter 0 Clock Select" "0: Disabled / Reset,1: Card Clock,2: Receive Clock,3: ETU Clock (transmit clock)" bitfld.long 0x0 8.--9. "GPCNT1_CLK_SEL,General Purpose Counter 1 Clock Select" "0: Disabled / Reset,1: Card Clock,2: Receive Clock,3: ETU Clock (transmit clock)" newline hexmask.long.byte 0x0 0.--7. 1. "CLK_PRSC,Clock Prescaler Value" line.long 0x4 "DIVISOR,Baud Rate Divisor Register" hexmask.long.word 0x4 0.--8. 1. "DIVISOR_VALUE,Divisor (F/D) Value" line.long 0x8 "CTRL,Control Register" bitfld.long 0x8 31. "BWT_EN,Block Wait Time Counter Enable" "0: Disable BWT BGT Counters,1: Enable BWT BGT Counters" bitfld.long 0x8 30. "XMT_CRC_LRC,Transmit CRC or LRC Enable" "0: No CRC or LRC value is transmitted,1: Transmit LRC or CRC info when FIFO empties.." newline bitfld.long 0x8 29. "CRC_EN,CRC Enable" "0: 16-bit Cyclic Redundancy Checking disabled,1: 16-bit Cyclic Redundancy Checking enabled" bitfld.long 0x8 28. "LRC_EN,LRC Enable" "0: 8-bit Linear Redundancy Checking disabled,1: 8-bit Linear Redundancy Checking enabled" newline bitfld.long 0x8 27. "CWT_EN,Character Wait Time Counter Enable" "0: Character Wait time Counter is disabled,1: Character Wait time counter is enabled" bitfld.long 0x8 26. "CRC_IN_FLIP,CRC Input Byte's Bit Reversal or Flip Control" "0: Bits in the input byte are not reversed (i.e.,1: Bits in the input byte are reversed (i.e. 7:0.." newline bitfld.long 0x8 25. "CRC_OUT_FLIP,CRC Output Value Bit Reversal or Flip" "0: Bits within the CRC output bytes are not..,1: Bits within the CRC output bytes are reversed.." bitfld.long 0x8 24. "INV_CRC_VAL,Invert bits in the CRC Output Value" "0: Bits in CRC Output value are not inverted.,1: Bits in CRC Output value are inverted." newline bitfld.long 0x8 20. "TX_DMA_EN,Transmit DMA Enable" "0: No DMA Write Request asserted for Transmitter,1: DMA Write Request asserted for Transmitter" bitfld.long 0x8 19. "RX_DMA_EN,Receive DMA Enable" "0: No DMA Read Request asserted for Receiver,1: DMA Read Request asserted for Receiver" newline bitfld.long 0x8 18. "RCVR_11,Receiver 11 ETU Mode Enable" "0: Receiver configured for 12 ETU operation mode,1: Receiver configured for 11 ETU operation mode" bitfld.long 0x8 17. "XMT_EN,Transmitter Enable" "0: EMVSIM Transmitter disabled,1: EMVSIM Transmitter enabled" newline bitfld.long 0x8 16. "RCV_EN,Receiver Enable" "0: EMVSIM Receiver disabled,1: EMVSIM Receiver enabled" bitfld.long 0x8 13. "STOP_EN,STOP Enable" "0: STOP instruction shuts down all EMVSIM clocks,1: STOP instruction shuts down all clocks except.." newline bitfld.long 0x8 12. "DOZE_EN,Doze Enable" "0: DOZE instruction gates all internal EMVSIM..,1: DOZE instruction has no effect on EMVSIM module" bitfld.long 0x8 11. "KILL_CLOCKS,Kill all internal clocks" "0: EMVSIM input clock enabled,1: EMVSIM input clock is disabled" newline bitfld.long 0x8 10. "SW_RST,Software Reset Bit" "0: EMVSIM Normal operation,1: EMVSIM held in Reset" bitfld.long 0x8 9. "FLSH_TX,Flush Transmitter Bit" "0: EMVSIM Transmitter normal operation,1: EMVSIM Transmitter held in Reset" newline bitfld.long 0x8 8. "FLSH_RX,Flush Receiver Bit" "0: EMVSIM Receiver normal operation,1: EMVSIM Receiver held in Reset" bitfld.long 0x8 3. "ONACK,Overrun NACK Enable" "0: NACK generation on overrun is disabled,1: NACK generation on overrun is enabled" newline bitfld.long 0x8 2. "ANACK,Auto NACK Enable" "0: NACK generation on errors disabled,1: NACK generation on errors enabled" bitfld.long 0x8 1. "ICM,Initial Character Mode" "0: Initial Character Mode disabled,1: Initial Character Mode enabled" newline bitfld.long 0x8 0. "IC,Inverse Convention" "0: Direction convention transfers enabled,1: Inverse convention transfers enabled" line.long 0xC "INT_MASK,Interrupt Mask Register" bitfld.long 0xC 15. "PEF_IM,Parity Error Interrupt Mask" "0: PEF interrupt enabled,1: PEF interrupt masked" bitfld.long 0xC 14. "RX_DATA_IM,Receive Data Interrupt Mask" "0: RX_DATA interrupt enabled,1: RX_DATA interrupt masked" newline bitfld.long 0xC 13. "GPCNT1_IM,General Purpose Counter 1 Timeout Interrupt Mask" "0: GPCNT1_TO interrupt enabled,1: GPCNT1_TO interrupt masked" bitfld.long 0xC 12. "BGT_ERR_IM,Block Guard Time Error Interrupt" "0: BGT_ERR interrupt enabled,1: BGT_ERR interrupt masked" newline bitfld.long 0xC 11. "BWT_ERR_IM,Block Wait Time Error Interrupt Mask" "0: BWT_ERR interrupt enabled,1: BWT_ERR interrupt masked" bitfld.long 0xC 10. "RNACK_IM,Receiver NACK Threshold Interrupt Mask" "0: RTE interrupt enabled,1: RTE interrupt masked" newline bitfld.long 0xC 9. "CWT_ERR_IM,Character Wait Time Error Interrupt Mask" "0: CWT_ERR interrupt enabled,1: CWT_ERR interrupt masked" bitfld.long 0xC 8. "GPCNT0_IM,General Purpose Timer 0 Timeout Interrupt Mask" "0: GPCNT0_TO interrupt enabled,1: GPCNT0_TO interrupt masked" newline bitfld.long 0xC 7. "TDT_IM,Transmit Data Threshold Interrupt Mask" "0: TDTF interrupt enabled,1: TDTF interrupt masked" bitfld.long 0xC 6. "TFF_IM,Transmit FIFO Full Interrupt Mask" "0: TFF interrupt enabled,1: TFF interrupt masked" newline bitfld.long 0xC 5. "TNACK_IM,Transmit NACK Threshold Interrupt Mask" "0: TNTE interrupt enabled,1: TNTE interrupt masked" bitfld.long 0xC 4. "TFE_IM,Transmit FIFO Empty Interrupt Mask" "0: TFE interrupt enabled,1: TFE interrupt masked" newline bitfld.long 0xC 3. "ETC_IM,Early Transmit Complete Interrupt Mask" "0: ETC interrupt enabled,1: ETC interrupt masked" bitfld.long 0xC 2. "RFO_IM,Receive FIFO Overflow Interrupt Mask" "0: RFO interrupt enabled,1: RFO interrupt masked" newline bitfld.long 0xC 1. "TC_IM,Transmit Complete Interrupt Mask" "0: TCF interrupt enabled,1: TCF interrupt masked" bitfld.long 0xC 0. "RDT_IM,Receive Data Threshold Interrupt Mask" "0: RDTF interrupt enabled,1: RDTF interrupt masked" line.long 0x10 "RX_THD,Receiver Threshold Register" hexmask.long.byte 0x10 8.--11. 1. "RNCK_THD,Receiver NACK Threshold Value" hexmask.long.byte 0x10 0.--3. 1. "RDT,Receiver Data Threshold Value" line.long 0x14 "TX_THD,Transmitter Threshold Register" hexmask.long.byte 0x14 8.--11. 1. "TNCK_THD,Transmitter NACK Threshold Value" hexmask.long.byte 0x14 0.--3. 1. "TDT,Transmitter Data Threshold Value" line.long 0x18 "RX_STATUS,Receive Status Register" hexmask.long.byte 0x18 24.--27. 1. "RX_CNT,Receive FIFO Byte Count" hexmask.long.byte 0x18 16.--19. 1. "RX_WPTR,Receive FIFO Write Pointer Value" newline eventfld.long 0x18 13. "FEF,Frame Error Flag" "0: No frame error detected,1: Frame error detected" eventfld.long 0x18 12. "PEF,Parity Error Flag" "0: No parity error detected,1: Parity error detected" newline eventfld.long 0x18 11. "BGT_ERR,Block Guard Time Error Flag" "0: Block guard time was sufficient,1: Block guard time was too small" eventfld.long 0x18 10. "BWT_ERR,Block Wait Time Error Flag" "0: Block wait time not exceeded,1: Block wait time was exceeded" newline eventfld.long 0x18 9. "RTE,Received NACK Threshold Error Flag" "0: Number of NACKs generated by the receiver is..,1: Number of NACKs generated by the receiver is.." eventfld.long 0x18 8. "CWT_ERR,Character Wait Time Error Flag" "0: No CWT violation has occurred,1: Time between two consecutive characters has.." newline rbitfld.long 0x18 7. "CRC_OK,CRC Check OK Flag" "0: Current CRC value does not match remainder.,1: Current calculated CRC value matches the.." rbitfld.long 0x18 6. "LRC_OK,LRC Check OK Flag" "0: Current LRC value does not match remainder.,1: Current calculated LRC value matches the.." newline rbitfld.long 0x18 5. "RDTF,Receive Data Threshold Interrupt Flag" "0: Number of unread bytes in receive FIFO less than..,1: Number of unread bytes in receive FIFO greater.." eventfld.long 0x18 4. "RX_DATA,Receive Data Interrupt Flag" "0: No new byte is received,1: New byte is received ans stored in Receive FIFO" newline eventfld.long 0x18 0. "RFO,Receive FIFO Overflow Flag" "0: No overrun error has occurred,1: A byte was received when the received FIFO was.." line.long 0x1C "TX_STATUS,Transmitter Status Register" hexmask.long.byte 0x1C 24.--27. 1. "TX_CNT,Transmit FIFO Byte Count" hexmask.long.byte 0x1C 16.--19. 1. "TX_RPTR,Transmit FIFO Read Pointer" newline eventfld.long 0x1C 9. "GPCNT1_TO,General Purpose Counter 1 Timeout Flag" "0: GPCNT1 time not reached or bit has been cleared.,1: General Purpose counter has reached the GPCNT1.." eventfld.long 0x1C 8. "GPCNT0_TO,General Purpose Counter 0 Timeout Flag" "0: GPCNT0 time not reached or bit has been cleared.,1: General Purpose counter has reached the GPCNT0.." newline rbitfld.long 0x1C 7. "TDTF,Transmit Data Threshold Flag" "0: Number of bytes in FIFO is greater than TDT or..,1: Number of bytes in FIFO is less than or equal to.." eventfld.long 0x1C 6. "TFF,Transmit FIFO Full Flag" "0: Transmit FIFO Full condition has not occurred,1: A Transmit FIFO Full condition has occurred" newline eventfld.long 0x1C 5. "TCF,Transmit Complete Flag" "0: Transmit pending or in progress,1: Transmit complete" eventfld.long 0x1C 4. "ETCF,Early Transmit Complete Flag" "0: Transmit pending or in progress,1: Transmit complete" newline eventfld.long 0x1C 3. "TFE,Transmit FIFO Empty Flag" "0: Transmit FIFO is not empty,1: Transmit FIFO is empty" eventfld.long 0x1C 0. "TNTE,Transmit NACK Threshold Error Flag" "0: Transmit NACK threshold has not been reached,1: Transmit NACK threshold reached; transmitter.." line.long 0x20 "PCSR,Port Control and Status Register" bitfld.long 0x20 27. "SPDES,SIM Presence Detect Edge Select" "0: Falling edge on the pin,1: Rising edge on the pin" rbitfld.long 0x20 26. "SPDP,Smart Card Presence Detect Pin Status" "0: SIM Presence Detect pin is logic low,1: SIM Presence Detectpin is logic high" newline eventfld.long 0x20 25. "SPDIF,Smart Card Presence Detect Interrupt Flag" "0: No insertion or removal of Smart Card detected..,1: Insertion or removal of Smart Card detected on.." bitfld.long 0x20 24. "SPDIM,Smart Card Presence Detect Interrupt Mask" "0: SIM presence detect interrupt is enabled,1: SIM presence detect interrupt is masked" newline bitfld.long 0x20 7. "SPD,Auto Power Down Control" "0: No effect,1: Start Auto Powerdown or Power Down is in progress" bitfld.long 0x20 5. "SCSP,Smart Card Clock Stop Polarity" "0: Clock is logic 0 when stopped by SCEN,1: Clock is logic 1 when stopped by SCEN" newline bitfld.long 0x20 4. "SCEN,Clock Enable for Smart Card" "0: Smart Card Clock Disabled,1: Smart Card Clock Enabled" bitfld.long 0x20 3. "SRST,Reset to Smart Card" "0: Smart Card Reset is asserted,1: Smart Card Reset is de-asserted" newline bitfld.long 0x20 2. "VCCENP,VCC Enable Polarity Control" "0: SVCC_EN is active high. Polarity of SVCC_EN is..,1: SVCC_EN is active low. Polarity of SVCC_EN is.." bitfld.long 0x20 1. "SVCC_EN,Vcc Enable for Smart Card" "0: Smart Card Voltage disabled,1: Smart Card Voltage enabled" newline bitfld.long 0x20 0. "SAPD,Auto Power Down Enable" "0: Auto power down disabled,1: Auto power down enabled" rgroup.long 0x2C++0x3 line.long 0x0 "RX_BUF,Receive Data Read Buffer" hexmask.long.byte 0x0 0.--7. 1. "RX_BYTE,Receive Data Byte Read" group.long 0x30++0x1B line.long 0x0 "TX_BUF,Transmit Data Buffer" hexmask.long.byte 0x0 0.--7. 1. "TX_BYTE,Transmit Data Byte" line.long 0x4 "TX_GETU,Transmitter Guard ETU Value Register" hexmask.long.byte 0x4 0.--7. 1. "GETU,Transmitter Guard Time Value in ETU" line.long 0x8 "CWT_VAL,Character Wait Time Value Register" hexmask.long.word 0x8 0.--15. 1. "CWT,Character Wait Time Value" line.long 0xC "BWT_VAL,Block Wait Time Value Register" hexmask.long 0xC 0.--31. 1. "BWT,Block Wait Time Value" line.long 0x10 "BGT_VAL,Block Guard Time Value Register" hexmask.long.word 0x10 0.--15. 1. "BGT,Block Guard Time Value" line.long 0x14 "GPCNT0_VAL,General Purpose Counter 0 Timeout Value Register" hexmask.long.word 0x14 0.--15. 1. "GPCNT0,General Purpose Counter 0 Timeout Value" line.long 0x18 "GPCNT1_VAL,General Purpose Counter 1 Timeout Value" hexmask.long.word 0x18 0.--15. 1. "GPCNT1,General Purpose Counter 1 Timeout Value" tree.end tree "EMVSIM2" base ad:0x40158000 rgroup.long 0x0++0x7 line.long 0x0 "VER_ID,Version ID Register" hexmask.long 0x0 0.--31. 1. "VER,Version ID of the module" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "TX_FIFO_DEPTH,Transmit FIFO Depth" hexmask.long.byte 0x4 0.--7. 1. "RX_FIFO_DEPTH,Receive FIFO Depth" group.long 0x8++0x23 line.long 0x0 "CLKCFG,Clock Configuration Register" bitfld.long 0x0 10.--11. "GPCNT0_CLK_SEL,General Purpose Counter 0 Clock Select" "0: Disabled / Reset,1: Card Clock,2: Receive Clock,3: ETU Clock (transmit clock)" bitfld.long 0x0 8.--9. "GPCNT1_CLK_SEL,General Purpose Counter 1 Clock Select" "0: Disabled / Reset,1: Card Clock,2: Receive Clock,3: ETU Clock (transmit clock)" newline hexmask.long.byte 0x0 0.--7. 1. "CLK_PRSC,Clock Prescaler Value" line.long 0x4 "DIVISOR,Baud Rate Divisor Register" hexmask.long.word 0x4 0.--8. 1. "DIVISOR_VALUE,Divisor (F/D) Value" line.long 0x8 "CTRL,Control Register" bitfld.long 0x8 31. "BWT_EN,Block Wait Time Counter Enable" "0: Disable BWT BGT Counters,1: Enable BWT BGT Counters" bitfld.long 0x8 30. "XMT_CRC_LRC,Transmit CRC or LRC Enable" "0: No CRC or LRC value is transmitted,1: Transmit LRC or CRC info when FIFO empties.." newline bitfld.long 0x8 29. "CRC_EN,CRC Enable" "0: 16-bit Cyclic Redundancy Checking disabled,1: 16-bit Cyclic Redundancy Checking enabled" bitfld.long 0x8 28. "LRC_EN,LRC Enable" "0: 8-bit Linear Redundancy Checking disabled,1: 8-bit Linear Redundancy Checking enabled" newline bitfld.long 0x8 27. "CWT_EN,Character Wait Time Counter Enable" "0: Character Wait time Counter is disabled,1: Character Wait time counter is enabled" bitfld.long 0x8 26. "CRC_IN_FLIP,CRC Input Byte's Bit Reversal or Flip Control" "0: Bits in the input byte are not reversed (i.e.,1: Bits in the input byte are reversed (i.e. 7:0.." newline bitfld.long 0x8 25. "CRC_OUT_FLIP,CRC Output Value Bit Reversal or Flip" "0: Bits within the CRC output bytes are not..,1: Bits within the CRC output bytes are reversed.." bitfld.long 0x8 24. "INV_CRC_VAL,Invert bits in the CRC Output Value" "0: Bits in CRC Output value are not inverted.,1: Bits in CRC Output value are inverted." newline bitfld.long 0x8 20. "TX_DMA_EN,Transmit DMA Enable" "0: No DMA Write Request asserted for Transmitter,1: DMA Write Request asserted for Transmitter" bitfld.long 0x8 19. "RX_DMA_EN,Receive DMA Enable" "0: No DMA Read Request asserted for Receiver,1: DMA Read Request asserted for Receiver" newline bitfld.long 0x8 18. "RCVR_11,Receiver 11 ETU Mode Enable" "0: Receiver configured for 12 ETU operation mode,1: Receiver configured for 11 ETU operation mode" bitfld.long 0x8 17. "XMT_EN,Transmitter Enable" "0: EMVSIM Transmitter disabled,1: EMVSIM Transmitter enabled" newline bitfld.long 0x8 16. "RCV_EN,Receiver Enable" "0: EMVSIM Receiver disabled,1: EMVSIM Receiver enabled" bitfld.long 0x8 13. "STOP_EN,STOP Enable" "0: STOP instruction shuts down all EMVSIM clocks,1: STOP instruction shuts down all clocks except.." newline bitfld.long 0x8 12. "DOZE_EN,Doze Enable" "0: DOZE instruction gates all internal EMVSIM..,1: DOZE instruction has no effect on EMVSIM module" bitfld.long 0x8 11. "KILL_CLOCKS,Kill all internal clocks" "0: EMVSIM input clock enabled,1: EMVSIM input clock is disabled" newline bitfld.long 0x8 10. "SW_RST,Software Reset Bit" "0: EMVSIM Normal operation,1: EMVSIM held in Reset" bitfld.long 0x8 9. "FLSH_TX,Flush Transmitter Bit" "0: EMVSIM Transmitter normal operation,1: EMVSIM Transmitter held in Reset" newline bitfld.long 0x8 8. "FLSH_RX,Flush Receiver Bit" "0: EMVSIM Receiver normal operation,1: EMVSIM Receiver held in Reset" bitfld.long 0x8 3. "ONACK,Overrun NACK Enable" "0: NACK generation on overrun is disabled,1: NACK generation on overrun is enabled" newline bitfld.long 0x8 2. "ANACK,Auto NACK Enable" "0: NACK generation on errors disabled,1: NACK generation on errors enabled" bitfld.long 0x8 1. "ICM,Initial Character Mode" "0: Initial Character Mode disabled,1: Initial Character Mode enabled" newline bitfld.long 0x8 0. "IC,Inverse Convention" "0: Direction convention transfers enabled,1: Inverse convention transfers enabled" line.long 0xC "INT_MASK,Interrupt Mask Register" bitfld.long 0xC 15. "PEF_IM,Parity Error Interrupt Mask" "0: PEF interrupt enabled,1: PEF interrupt masked" bitfld.long 0xC 14. "RX_DATA_IM,Receive Data Interrupt Mask" "0: RX_DATA interrupt enabled,1: RX_DATA interrupt masked" newline bitfld.long 0xC 13. "GPCNT1_IM,General Purpose Counter 1 Timeout Interrupt Mask" "0: GPCNT1_TO interrupt enabled,1: GPCNT1_TO interrupt masked" bitfld.long 0xC 12. "BGT_ERR_IM,Block Guard Time Error Interrupt" "0: BGT_ERR interrupt enabled,1: BGT_ERR interrupt masked" newline bitfld.long 0xC 11. "BWT_ERR_IM,Block Wait Time Error Interrupt Mask" "0: BWT_ERR interrupt enabled,1: BWT_ERR interrupt masked" bitfld.long 0xC 10. "RNACK_IM,Receiver NACK Threshold Interrupt Mask" "0: RTE interrupt enabled,1: RTE interrupt masked" newline bitfld.long 0xC 9. "CWT_ERR_IM,Character Wait Time Error Interrupt Mask" "0: CWT_ERR interrupt enabled,1: CWT_ERR interrupt masked" bitfld.long 0xC 8. "GPCNT0_IM,General Purpose Timer 0 Timeout Interrupt Mask" "0: GPCNT0_TO interrupt enabled,1: GPCNT0_TO interrupt masked" newline bitfld.long 0xC 7. "TDT_IM,Transmit Data Threshold Interrupt Mask" "0: TDTF interrupt enabled,1: TDTF interrupt masked" bitfld.long 0xC 6. "TFF_IM,Transmit FIFO Full Interrupt Mask" "0: TFF interrupt enabled,1: TFF interrupt masked" newline bitfld.long 0xC 5. "TNACK_IM,Transmit NACK Threshold Interrupt Mask" "0: TNTE interrupt enabled,1: TNTE interrupt masked" bitfld.long 0xC 4. "TFE_IM,Transmit FIFO Empty Interrupt Mask" "0: TFE interrupt enabled,1: TFE interrupt masked" newline bitfld.long 0xC 3. "ETC_IM,Early Transmit Complete Interrupt Mask" "0: ETC interrupt enabled,1: ETC interrupt masked" bitfld.long 0xC 2. "RFO_IM,Receive FIFO Overflow Interrupt Mask" "0: RFO interrupt enabled,1: RFO interrupt masked" newline bitfld.long 0xC 1. "TC_IM,Transmit Complete Interrupt Mask" "0: TCF interrupt enabled,1: TCF interrupt masked" bitfld.long 0xC 0. "RDT_IM,Receive Data Threshold Interrupt Mask" "0: RDTF interrupt enabled,1: RDTF interrupt masked" line.long 0x10 "RX_THD,Receiver Threshold Register" hexmask.long.byte 0x10 8.--11. 1. "RNCK_THD,Receiver NACK Threshold Value" hexmask.long.byte 0x10 0.--3. 1. "RDT,Receiver Data Threshold Value" line.long 0x14 "TX_THD,Transmitter Threshold Register" hexmask.long.byte 0x14 8.--11. 1. "TNCK_THD,Transmitter NACK Threshold Value" hexmask.long.byte 0x14 0.--3. 1. "TDT,Transmitter Data Threshold Value" line.long 0x18 "RX_STATUS,Receive Status Register" hexmask.long.byte 0x18 24.--27. 1. "RX_CNT,Receive FIFO Byte Count" hexmask.long.byte 0x18 16.--19. 1. "RX_WPTR,Receive FIFO Write Pointer Value" newline eventfld.long 0x18 13. "FEF,Frame Error Flag" "0: No frame error detected,1: Frame error detected" eventfld.long 0x18 12. "PEF,Parity Error Flag" "0: No parity error detected,1: Parity error detected" newline eventfld.long 0x18 11. "BGT_ERR,Block Guard Time Error Flag" "0: Block guard time was sufficient,1: Block guard time was too small" eventfld.long 0x18 10. "BWT_ERR,Block Wait Time Error Flag" "0: Block wait time not exceeded,1: Block wait time was exceeded" newline eventfld.long 0x18 9. "RTE,Received NACK Threshold Error Flag" "0: Number of NACKs generated by the receiver is..,1: Number of NACKs generated by the receiver is.." eventfld.long 0x18 8. "CWT_ERR,Character Wait Time Error Flag" "0: No CWT violation has occurred,1: Time between two consecutive characters has.." newline rbitfld.long 0x18 7. "CRC_OK,CRC Check OK Flag" "0: Current CRC value does not match remainder.,1: Current calculated CRC value matches the.." rbitfld.long 0x18 6. "LRC_OK,LRC Check OK Flag" "0: Current LRC value does not match remainder.,1: Current calculated LRC value matches the.." newline rbitfld.long 0x18 5. "RDTF,Receive Data Threshold Interrupt Flag" "0: Number of unread bytes in receive FIFO less than..,1: Number of unread bytes in receive FIFO greater.." eventfld.long 0x18 4. "RX_DATA,Receive Data Interrupt Flag" "0: No new byte is received,1: New byte is received ans stored in Receive FIFO" newline eventfld.long 0x18 0. "RFO,Receive FIFO Overflow Flag" "0: No overrun error has occurred,1: A byte was received when the received FIFO was.." line.long 0x1C "TX_STATUS,Transmitter Status Register" hexmask.long.byte 0x1C 24.--27. 1. "TX_CNT,Transmit FIFO Byte Count" hexmask.long.byte 0x1C 16.--19. 1. "TX_RPTR,Transmit FIFO Read Pointer" newline eventfld.long 0x1C 9. "GPCNT1_TO,General Purpose Counter 1 Timeout Flag" "0: GPCNT1 time not reached or bit has been cleared.,1: General Purpose counter has reached the GPCNT1.." eventfld.long 0x1C 8. "GPCNT0_TO,General Purpose Counter 0 Timeout Flag" "0: GPCNT0 time not reached or bit has been cleared.,1: General Purpose counter has reached the GPCNT0.." newline rbitfld.long 0x1C 7. "TDTF,Transmit Data Threshold Flag" "0: Number of bytes in FIFO is greater than TDT or..,1: Number of bytes in FIFO is less than or equal to.." eventfld.long 0x1C 6. "TFF,Transmit FIFO Full Flag" "0: Transmit FIFO Full condition has not occurred,1: A Transmit FIFO Full condition has occurred" newline eventfld.long 0x1C 5. "TCF,Transmit Complete Flag" "0: Transmit pending or in progress,1: Transmit complete" eventfld.long 0x1C 4. "ETCF,Early Transmit Complete Flag" "0: Transmit pending or in progress,1: Transmit complete" newline eventfld.long 0x1C 3. "TFE,Transmit FIFO Empty Flag" "0: Transmit FIFO is not empty,1: Transmit FIFO is empty" eventfld.long 0x1C 0. "TNTE,Transmit NACK Threshold Error Flag" "0: Transmit NACK threshold has not been reached,1: Transmit NACK threshold reached; transmitter.." line.long 0x20 "PCSR,Port Control and Status Register" bitfld.long 0x20 27. "SPDES,SIM Presence Detect Edge Select" "0: Falling edge on the pin,1: Rising edge on the pin" rbitfld.long 0x20 26. "SPDP,Smart Card Presence Detect Pin Status" "0: SIM Presence Detect pin is logic low,1: SIM Presence Detectpin is logic high" newline eventfld.long 0x20 25. "SPDIF,Smart Card Presence Detect Interrupt Flag" "0: No insertion or removal of Smart Card detected..,1: Insertion or removal of Smart Card detected on.." bitfld.long 0x20 24. "SPDIM,Smart Card Presence Detect Interrupt Mask" "0: SIM presence detect interrupt is enabled,1: SIM presence detect interrupt is masked" newline bitfld.long 0x20 7. "SPD,Auto Power Down Control" "0: No effect,1: Start Auto Powerdown or Power Down is in progress" bitfld.long 0x20 5. "SCSP,Smart Card Clock Stop Polarity" "0: Clock is logic 0 when stopped by SCEN,1: Clock is logic 1 when stopped by SCEN" newline bitfld.long 0x20 4. "SCEN,Clock Enable for Smart Card" "0: Smart Card Clock Disabled,1: Smart Card Clock Enabled" bitfld.long 0x20 3. "SRST,Reset to Smart Card" "0: Smart Card Reset is asserted,1: Smart Card Reset is de-asserted" newline bitfld.long 0x20 2. "VCCENP,VCC Enable Polarity Control" "0: SVCC_EN is active high. Polarity of SVCC_EN is..,1: SVCC_EN is active low. Polarity of SVCC_EN is.." bitfld.long 0x20 1. "SVCC_EN,Vcc Enable for Smart Card" "0: Smart Card Voltage disabled,1: Smart Card Voltage enabled" newline bitfld.long 0x20 0. "SAPD,Auto Power Down Enable" "0: Auto power down disabled,1: Auto power down enabled" rgroup.long 0x2C++0x3 line.long 0x0 "RX_BUF,Receive Data Read Buffer" hexmask.long.byte 0x0 0.--7. 1. "RX_BYTE,Receive Data Byte Read" group.long 0x30++0x1B line.long 0x0 "TX_BUF,Transmit Data Buffer" hexmask.long.byte 0x0 0.--7. 1. "TX_BYTE,Transmit Data Byte" line.long 0x4 "TX_GETU,Transmitter Guard ETU Value Register" hexmask.long.byte 0x4 0.--7. 1. "GETU,Transmitter Guard Time Value in ETU" line.long 0x8 "CWT_VAL,Character Wait Time Value Register" hexmask.long.word 0x8 0.--15. 1. "CWT,Character Wait Time Value" line.long 0xC "BWT_VAL,Block Wait Time Value Register" hexmask.long 0xC 0.--31. 1. "BWT,Block Wait Time Value" line.long 0x10 "BGT_VAL,Block Guard Time Value Register" hexmask.long.word 0x10 0.--15. 1. "BGT,Block Guard Time Value" line.long 0x14 "GPCNT0_VAL,General Purpose Counter 0 Timeout Value Register" hexmask.long.word 0x14 0.--15. 1. "GPCNT0,General Purpose Counter 0 Timeout Value" line.long 0x18 "GPCNT1_VAL,General Purpose Counter 1 Timeout Value" hexmask.long.word 0x18 0.--15. 1. "GPCNT1,General Purpose Counter 1 Timeout Value" tree.end tree.end tree "ENC" base ad:0x0 tree "ENC1" base ad:0x40174000 group.word 0x0++0x7 line.word 0x0 "CTRL,Control Register" eventfld.word 0x0 15. "HIRQ,HOME Signal Transition Interrupt Request" "0: No transition on the HOME signal has occurred,1: A transition on the HOME signal has occurred" bitfld.word 0x0 14. "HIE,HOME Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "HIP,Enable HOME to Initialize Position Counters UPOS and LPOS" "0: No action,1: HOME signal initializes the position counter" bitfld.word 0x0 12. "HNE,Use Negative Edge of HOME Input" "0: Use positive-going edge-to-trigger..,1: Use negative-going edge-to-trigger.." newline bitfld.word 0x0 11. "SWIP,Software-Triggered Initialization of Position Counters UPOS and LPOS" "0: No action,1: Initialize position counter (using upper and.." bitfld.word 0x0 10. "REV,Enable Reverse Direction Counting" "0: Count normally,1: Count in the reverse direction" newline bitfld.word 0x0 9. "PH1,Enable Signal Phase Count Mode" "0: Use the standard quadrature decoder where PHASEA..,1: Bypass the quadrature decoder. A positive.." eventfld.word 0x0 8. "XIRQ,INDEX Pulse Interrupt Request" "0: INDEX pulse has not occurred,1: INDEX pulse has occurred" newline bitfld.word 0x0 7. "XIE,INDEX Pulse Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 6. "XIP,INDEX Triggered Initialization of Position Counters UPOS and LPOS" "0: INDEX pulse does not initialize the position..,1: INDEX pulse initializes the position counter" newline bitfld.word 0x0 5. "XNE,Use Negative Edge of INDEX Pulse" "0: Use positive edge of INDEX pulse,1: Use negative edge of INDEX pulse" eventfld.word 0x0 4. "DIRQ,Watchdog Timeout Interrupt Request" "0: No Watchdog timeout interrupt has occurred,1: Watchdog timeout interrupt has occurred" newline bitfld.word 0x0 3. "DIE,Watchdog Timeout Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 2. "WDE,Watchdog Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x0 1. "CMPIRQ,Compare Interrupt Request" "0: No match has occurred (the counter does not..,1: COMP match has occurred (the counter matches the.." bitfld.word 0x0 0. "CMPIE,Compare Interrupt Enable" "0: Disabled,1: Enabled" line.word 0x2 "FILT,Input Filter Register" bitfld.word 0x2 13.--15. "FILT_PRSC,prescaler divide IPbus clock to FILT clk" "0,1,2,3,4,5,6,7" bitfld.word 0x2 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x2 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x4 "WTR,Watchdog Timeout Register" hexmask.word 0x4 0.--15. 1. "WDOG,WDOG" line.word 0x6 "POSD,Position Difference Counter Register" hexmask.word 0x6 0.--15. 1. "POSD,POSD" rgroup.word 0x8++0x1 line.word 0x0 "POSDH,Position Difference Hold Register" hexmask.word 0x0 0.--15. 1. "POSDH,POSDH" group.word 0xA++0x1 line.word 0x0 "REV,Revolution Counter Register" hexmask.word 0x0 0.--15. 1. "REV,REV" rgroup.word 0xC++0x1 line.word 0x0 "REVH,Revolution Hold Register" hexmask.word 0x0 0.--15. 1. "REVH,REVH" group.word 0xE++0x3 line.word 0x0 "UPOS,Upper Position Counter Register" hexmask.word 0x0 0.--15. 1. "POS,POS" line.word 0x2 "LPOS,Lower Position Counter Register" hexmask.word 0x2 0.--15. 1. "POS,POS" rgroup.word 0x12++0x3 line.word 0x0 "UPOSH,Upper Position Hold Register" hexmask.word 0x0 0.--15. 1. "POSH,POSH" line.word 0x2 "LPOSH,Lower Position Hold Register" hexmask.word 0x2 0.--15. 1. "POSH,POSH" group.word 0x16++0x3 line.word 0x0 "UINIT,Upper Initialization Register" hexmask.word 0x0 0.--15. 1. "INIT,INIT" line.word 0x2 "LINIT,Lower Initialization Register" hexmask.word 0x2 0.--15. 1. "INIT,INIT" rgroup.word 0x1A++0x1 line.word 0x0 "IMR,Input Monitor Register" bitfld.word 0x0 7. "FPHA,FPHA" "0,1" bitfld.word 0x0 6. "FPHB,FPHB" "0,1" newline bitfld.word 0x0 5. "FIND,FIND" "0,1" bitfld.word 0x0 4. "FHOM,FHOM" "0,1" newline bitfld.word 0x0 3. "PHA,PHA" "0,1" bitfld.word 0x0 2. "PHB,PHB" "0,1" newline bitfld.word 0x0 1. "INDEX,INDEX" "0,1" bitfld.word 0x0 0. "HOME,HOME" "0,1" group.word 0x1C++0xB line.word 0x0 "TST,Test Register" bitfld.word 0x0 15. "TEN,Test Mode Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 14. "TCE,Test Counter Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "QDN,Quadrature Decoder Negative Signal" "0: Generates a positive quadrature decoder signal,1: Generates a negative quadrature decoder signal" hexmask.word.byte 0x0 8.--12. 1. "TEST_PERIOD,TEST_PERIOD" newline hexmask.word.byte 0x0 0.--7. 1. "TEST_COUNT,TEST_COUNT" line.word 0x2 "CTRL2,Control 2 Register" eventfld.word 0x2 11. "SABIRQ,Simultaneous PHASEA and PHASEB Change Interrupt Request" "0: No simultaneous change of PHASEA and PHASEB has..,1: A simultaneous change of PHASEA and PHASEB has.." bitfld.word 0x2 10. "SABIE,Simultaneous PHASEA and PHASEB Change Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x2 9. "OUTCTL,Output Control" "0: POSMATCH pulses when a match occurs between the..,1: POSMATCH pulses when the UPOS LPOS REV or POSD.." bitfld.word 0x2 8. "REVMOD,Revolution Counter Modulus Enable" "0: Use INDEX pulse to increment/decrement..,1: Use modulus counting roll-over/under to.." newline eventfld.word 0x2 7. "ROIRQ,Roll-over Interrupt Request" "0: No roll-over has occurred,1: Roll-over has occurred" bitfld.word 0x2 6. "ROIE,Roll-over Interrupt Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x2 5. "RUIRQ,Roll-under Interrupt Request" "0: No roll-under has occurred,1: Roll-under has occurred" bitfld.word 0x2 4. "RUIE,Roll-under Interrupt Enable" "0: Disabled,1: Enabled" newline rbitfld.word 0x2 3. "DIR,Count Direction Flag" "0: Last count was in the down direction,1: Last count was in the up direction" bitfld.word 0x2 2. "MOD,Enable Modulo Counting" "0: Disable modulo counting,1: Enable modulo counting" newline bitfld.word 0x2 1. "UPDPOS,Update Position Registers" "0: No action for POSD REV UPOS and LPOS registers..,1: Clear POSD REV UPOS and LPOS registers on rising.." bitfld.word 0x2 0. "UPDHLD,Update Hold Registers" "0: Disable updates of hold registers on the rising..,1: Enable updates of hold registers on the rising.." line.word 0x4 "UMOD,Upper Modulus Register" hexmask.word 0x4 0.--15. 1. "MOD,MOD" line.word 0x6 "LMOD,Lower Modulus Register" hexmask.word 0x6 0.--15. 1. "MOD,MOD" line.word 0x8 "UCOMP,Upper Position Compare Register" hexmask.word 0x8 0.--15. 1. "COMP,COMP" line.word 0xA "LCOMP,Lower Position Compare Register" hexmask.word 0xA 0.--15. 1. "COMP,COMP" rgroup.word 0x28++0x9 line.word 0x0 "LASTEDGE,Last Edge Time Register" hexmask.word 0x0 0.--15. 1. "LASTEDGE,Last Edge Time Counter" line.word 0x2 "LASTEDGEH,Last Edge Time Hold Register" hexmask.word 0x2 0.--15. 1. "LASTEDGEH,Last Edge Time Hold" line.word 0x4 "POSDPER,Position Difference Period Counter Register" hexmask.word 0x4 0.--15. 1. "POSDPER,Position difference period" line.word 0x6 "POSDPERBFR,Position Difference Period Buffer Register" hexmask.word 0x6 0.--15. 1. "POSDPERBFR,Position difference period buffer" line.word 0x8 "POSDPERH,Position Difference Period Hold Register" hexmask.word 0x8 0.--15. 1. "POSDPERH,Position difference period hold" group.word 0x32++0x1 line.word 0x0 "CTRL3,Control 3 Register" hexmask.word.byte 0x0 4.--7. 1. "PRSC,Prescaler" bitfld.word 0x0 0. "PMEN,Period measurement function enable" "0: Period measurement functions are not used. POSD..,1: Period measurement functions are used. POSD is.." tree.end tree "ENC2" base ad:0x40178000 group.word 0x0++0x7 line.word 0x0 "CTRL,Control Register" eventfld.word 0x0 15. "HIRQ,HOME Signal Transition Interrupt Request" "0: No transition on the HOME signal has occurred,1: A transition on the HOME signal has occurred" bitfld.word 0x0 14. "HIE,HOME Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "HIP,Enable HOME to Initialize Position Counters UPOS and LPOS" "0: No action,1: HOME signal initializes the position counter" bitfld.word 0x0 12. "HNE,Use Negative Edge of HOME Input" "0: Use positive-going edge-to-trigger..,1: Use negative-going edge-to-trigger.." newline bitfld.word 0x0 11. "SWIP,Software-Triggered Initialization of Position Counters UPOS and LPOS" "0: No action,1: Initialize position counter (using upper and.." bitfld.word 0x0 10. "REV,Enable Reverse Direction Counting" "0: Count normally,1: Count in the reverse direction" newline bitfld.word 0x0 9. "PH1,Enable Signal Phase Count Mode" "0: Use the standard quadrature decoder where PHASEA..,1: Bypass the quadrature decoder. A positive.." eventfld.word 0x0 8. "XIRQ,INDEX Pulse Interrupt Request" "0: INDEX pulse has not occurred,1: INDEX pulse has occurred" newline bitfld.word 0x0 7. "XIE,INDEX Pulse Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 6. "XIP,INDEX Triggered Initialization of Position Counters UPOS and LPOS" "0: INDEX pulse does not initialize the position..,1: INDEX pulse initializes the position counter" newline bitfld.word 0x0 5. "XNE,Use Negative Edge of INDEX Pulse" "0: Use positive edge of INDEX pulse,1: Use negative edge of INDEX pulse" eventfld.word 0x0 4. "DIRQ,Watchdog Timeout Interrupt Request" "0: No Watchdog timeout interrupt has occurred,1: Watchdog timeout interrupt has occurred" newline bitfld.word 0x0 3. "DIE,Watchdog Timeout Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 2. "WDE,Watchdog Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x0 1. "CMPIRQ,Compare Interrupt Request" "0: No match has occurred (the counter does not..,1: COMP match has occurred (the counter matches the.." bitfld.word 0x0 0. "CMPIE,Compare Interrupt Enable" "0: Disabled,1: Enabled" line.word 0x2 "FILT,Input Filter Register" bitfld.word 0x2 13.--15. "FILT_PRSC,prescaler divide IPbus clock to FILT clk" "0,1,2,3,4,5,6,7" bitfld.word 0x2 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x2 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x4 "WTR,Watchdog Timeout Register" hexmask.word 0x4 0.--15. 1. "WDOG,WDOG" line.word 0x6 "POSD,Position Difference Counter Register" hexmask.word 0x6 0.--15. 1. "POSD,POSD" rgroup.word 0x8++0x1 line.word 0x0 "POSDH,Position Difference Hold Register" hexmask.word 0x0 0.--15. 1. "POSDH,POSDH" group.word 0xA++0x1 line.word 0x0 "REV,Revolution Counter Register" hexmask.word 0x0 0.--15. 1. "REV,REV" rgroup.word 0xC++0x1 line.word 0x0 "REVH,Revolution Hold Register" hexmask.word 0x0 0.--15. 1. "REVH,REVH" group.word 0xE++0x3 line.word 0x0 "UPOS,Upper Position Counter Register" hexmask.word 0x0 0.--15. 1. "POS,POS" line.word 0x2 "LPOS,Lower Position Counter Register" hexmask.word 0x2 0.--15. 1. "POS,POS" rgroup.word 0x12++0x3 line.word 0x0 "UPOSH,Upper Position Hold Register" hexmask.word 0x0 0.--15. 1. "POSH,POSH" line.word 0x2 "LPOSH,Lower Position Hold Register" hexmask.word 0x2 0.--15. 1. "POSH,POSH" group.word 0x16++0x3 line.word 0x0 "UINIT,Upper Initialization Register" hexmask.word 0x0 0.--15. 1. "INIT,INIT" line.word 0x2 "LINIT,Lower Initialization Register" hexmask.word 0x2 0.--15. 1. "INIT,INIT" rgroup.word 0x1A++0x1 line.word 0x0 "IMR,Input Monitor Register" bitfld.word 0x0 7. "FPHA,FPHA" "0,1" bitfld.word 0x0 6. "FPHB,FPHB" "0,1" newline bitfld.word 0x0 5. "FIND,FIND" "0,1" bitfld.word 0x0 4. "FHOM,FHOM" "0,1" newline bitfld.word 0x0 3. "PHA,PHA" "0,1" bitfld.word 0x0 2. "PHB,PHB" "0,1" newline bitfld.word 0x0 1. "INDEX,INDEX" "0,1" bitfld.word 0x0 0. "HOME,HOME" "0,1" group.word 0x1C++0xB line.word 0x0 "TST,Test Register" bitfld.word 0x0 15. "TEN,Test Mode Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 14. "TCE,Test Counter Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "QDN,Quadrature Decoder Negative Signal" "0: Generates a positive quadrature decoder signal,1: Generates a negative quadrature decoder signal" hexmask.word.byte 0x0 8.--12. 1. "TEST_PERIOD,TEST_PERIOD" newline hexmask.word.byte 0x0 0.--7. 1. "TEST_COUNT,TEST_COUNT" line.word 0x2 "CTRL2,Control 2 Register" eventfld.word 0x2 11. "SABIRQ,Simultaneous PHASEA and PHASEB Change Interrupt Request" "0: No simultaneous change of PHASEA and PHASEB has..,1: A simultaneous change of PHASEA and PHASEB has.." bitfld.word 0x2 10. "SABIE,Simultaneous PHASEA and PHASEB Change Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x2 9. "OUTCTL,Output Control" "0: POSMATCH pulses when a match occurs between the..,1: POSMATCH pulses when the UPOS LPOS REV or POSD.." bitfld.word 0x2 8. "REVMOD,Revolution Counter Modulus Enable" "0: Use INDEX pulse to increment/decrement..,1: Use modulus counting roll-over/under to.." newline eventfld.word 0x2 7. "ROIRQ,Roll-over Interrupt Request" "0: No roll-over has occurred,1: Roll-over has occurred" bitfld.word 0x2 6. "ROIE,Roll-over Interrupt Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x2 5. "RUIRQ,Roll-under Interrupt Request" "0: No roll-under has occurred,1: Roll-under has occurred" bitfld.word 0x2 4. "RUIE,Roll-under Interrupt Enable" "0: Disabled,1: Enabled" newline rbitfld.word 0x2 3. "DIR,Count Direction Flag" "0: Last count was in the down direction,1: Last count was in the up direction" bitfld.word 0x2 2. "MOD,Enable Modulo Counting" "0: Disable modulo counting,1: Enable modulo counting" newline bitfld.word 0x2 1. "UPDPOS,Update Position Registers" "0: No action for POSD REV UPOS and LPOS registers..,1: Clear POSD REV UPOS and LPOS registers on rising.." bitfld.word 0x2 0. "UPDHLD,Update Hold Registers" "0: Disable updates of hold registers on the rising..,1: Enable updates of hold registers on the rising.." line.word 0x4 "UMOD,Upper Modulus Register" hexmask.word 0x4 0.--15. 1. "MOD,MOD" line.word 0x6 "LMOD,Lower Modulus Register" hexmask.word 0x6 0.--15. 1. "MOD,MOD" line.word 0x8 "UCOMP,Upper Position Compare Register" hexmask.word 0x8 0.--15. 1. "COMP,COMP" line.word 0xA "LCOMP,Lower Position Compare Register" hexmask.word 0xA 0.--15. 1. "COMP,COMP" rgroup.word 0x28++0x9 line.word 0x0 "LASTEDGE,Last Edge Time Register" hexmask.word 0x0 0.--15. 1. "LASTEDGE,Last Edge Time Counter" line.word 0x2 "LASTEDGEH,Last Edge Time Hold Register" hexmask.word 0x2 0.--15. 1. "LASTEDGEH,Last Edge Time Hold" line.word 0x4 "POSDPER,Position Difference Period Counter Register" hexmask.word 0x4 0.--15. 1. "POSDPER,Position difference period" line.word 0x6 "POSDPERBFR,Position Difference Period Buffer Register" hexmask.word 0x6 0.--15. 1. "POSDPERBFR,Position difference period buffer" line.word 0x8 "POSDPERH,Position Difference Period Hold Register" hexmask.word 0x8 0.--15. 1. "POSDPERH,Position difference period hold" group.word 0x32++0x1 line.word 0x0 "CTRL3,Control 3 Register" hexmask.word.byte 0x0 4.--7. 1. "PRSC,Prescaler" bitfld.word 0x0 0. "PMEN,Period measurement function enable" "0: Period measurement functions are not used. POSD..,1: Period measurement functions are used. POSD is.." tree.end tree "ENC3" base ad:0x4017C000 group.word 0x0++0x7 line.word 0x0 "CTRL,Control Register" eventfld.word 0x0 15. "HIRQ,HOME Signal Transition Interrupt Request" "0: No transition on the HOME signal has occurred,1: A transition on the HOME signal has occurred" bitfld.word 0x0 14. "HIE,HOME Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "HIP,Enable HOME to Initialize Position Counters UPOS and LPOS" "0: No action,1: HOME signal initializes the position counter" bitfld.word 0x0 12. "HNE,Use Negative Edge of HOME Input" "0: Use positive-going edge-to-trigger..,1: Use negative-going edge-to-trigger.." newline bitfld.word 0x0 11. "SWIP,Software-Triggered Initialization of Position Counters UPOS and LPOS" "0: No action,1: Initialize position counter (using upper and.." bitfld.word 0x0 10. "REV,Enable Reverse Direction Counting" "0: Count normally,1: Count in the reverse direction" newline bitfld.word 0x0 9. "PH1,Enable Signal Phase Count Mode" "0: Use the standard quadrature decoder where PHASEA..,1: Bypass the quadrature decoder. A positive.." eventfld.word 0x0 8. "XIRQ,INDEX Pulse Interrupt Request" "0: INDEX pulse has not occurred,1: INDEX pulse has occurred" newline bitfld.word 0x0 7. "XIE,INDEX Pulse Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 6. "XIP,INDEX Triggered Initialization of Position Counters UPOS and LPOS" "0: INDEX pulse does not initialize the position..,1: INDEX pulse initializes the position counter" newline bitfld.word 0x0 5. "XNE,Use Negative Edge of INDEX Pulse" "0: Use positive edge of INDEX pulse,1: Use negative edge of INDEX pulse" eventfld.word 0x0 4. "DIRQ,Watchdog Timeout Interrupt Request" "0: No Watchdog timeout interrupt has occurred,1: Watchdog timeout interrupt has occurred" newline bitfld.word 0x0 3. "DIE,Watchdog Timeout Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 2. "WDE,Watchdog Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x0 1. "CMPIRQ,Compare Interrupt Request" "0: No match has occurred (the counter does not..,1: COMP match has occurred (the counter matches the.." bitfld.word 0x0 0. "CMPIE,Compare Interrupt Enable" "0: Disabled,1: Enabled" line.word 0x2 "FILT,Input Filter Register" bitfld.word 0x2 13.--15. "FILT_PRSC,prescaler divide IPbus clock to FILT clk" "0,1,2,3,4,5,6,7" bitfld.word 0x2 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x2 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x4 "WTR,Watchdog Timeout Register" hexmask.word 0x4 0.--15. 1. "WDOG,WDOG" line.word 0x6 "POSD,Position Difference Counter Register" hexmask.word 0x6 0.--15. 1. "POSD,POSD" rgroup.word 0x8++0x1 line.word 0x0 "POSDH,Position Difference Hold Register" hexmask.word 0x0 0.--15. 1. "POSDH,POSDH" group.word 0xA++0x1 line.word 0x0 "REV,Revolution Counter Register" hexmask.word 0x0 0.--15. 1. "REV,REV" rgroup.word 0xC++0x1 line.word 0x0 "REVH,Revolution Hold Register" hexmask.word 0x0 0.--15. 1. "REVH,REVH" group.word 0xE++0x3 line.word 0x0 "UPOS,Upper Position Counter Register" hexmask.word 0x0 0.--15. 1. "POS,POS" line.word 0x2 "LPOS,Lower Position Counter Register" hexmask.word 0x2 0.--15. 1. "POS,POS" rgroup.word 0x12++0x3 line.word 0x0 "UPOSH,Upper Position Hold Register" hexmask.word 0x0 0.--15. 1. "POSH,POSH" line.word 0x2 "LPOSH,Lower Position Hold Register" hexmask.word 0x2 0.--15. 1. "POSH,POSH" group.word 0x16++0x3 line.word 0x0 "UINIT,Upper Initialization Register" hexmask.word 0x0 0.--15. 1. "INIT,INIT" line.word 0x2 "LINIT,Lower Initialization Register" hexmask.word 0x2 0.--15. 1. "INIT,INIT" rgroup.word 0x1A++0x1 line.word 0x0 "IMR,Input Monitor Register" bitfld.word 0x0 7. "FPHA,FPHA" "0,1" bitfld.word 0x0 6. "FPHB,FPHB" "0,1" newline bitfld.word 0x0 5. "FIND,FIND" "0,1" bitfld.word 0x0 4. "FHOM,FHOM" "0,1" newline bitfld.word 0x0 3. "PHA,PHA" "0,1" bitfld.word 0x0 2. "PHB,PHB" "0,1" newline bitfld.word 0x0 1. "INDEX,INDEX" "0,1" bitfld.word 0x0 0. "HOME,HOME" "0,1" group.word 0x1C++0xB line.word 0x0 "TST,Test Register" bitfld.word 0x0 15. "TEN,Test Mode Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 14. "TCE,Test Counter Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "QDN,Quadrature Decoder Negative Signal" "0: Generates a positive quadrature decoder signal,1: Generates a negative quadrature decoder signal" hexmask.word.byte 0x0 8.--12. 1. "TEST_PERIOD,TEST_PERIOD" newline hexmask.word.byte 0x0 0.--7. 1. "TEST_COUNT,TEST_COUNT" line.word 0x2 "CTRL2,Control 2 Register" eventfld.word 0x2 11. "SABIRQ,Simultaneous PHASEA and PHASEB Change Interrupt Request" "0: No simultaneous change of PHASEA and PHASEB has..,1: A simultaneous change of PHASEA and PHASEB has.." bitfld.word 0x2 10. "SABIE,Simultaneous PHASEA and PHASEB Change Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x2 9. "OUTCTL,Output Control" "0: POSMATCH pulses when a match occurs between the..,1: POSMATCH pulses when the UPOS LPOS REV or POSD.." bitfld.word 0x2 8. "REVMOD,Revolution Counter Modulus Enable" "0: Use INDEX pulse to increment/decrement..,1: Use modulus counting roll-over/under to.." newline eventfld.word 0x2 7. "ROIRQ,Roll-over Interrupt Request" "0: No roll-over has occurred,1: Roll-over has occurred" bitfld.word 0x2 6. "ROIE,Roll-over Interrupt Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x2 5. "RUIRQ,Roll-under Interrupt Request" "0: No roll-under has occurred,1: Roll-under has occurred" bitfld.word 0x2 4. "RUIE,Roll-under Interrupt Enable" "0: Disabled,1: Enabled" newline rbitfld.word 0x2 3. "DIR,Count Direction Flag" "0: Last count was in the down direction,1: Last count was in the up direction" bitfld.word 0x2 2. "MOD,Enable Modulo Counting" "0: Disable modulo counting,1: Enable modulo counting" newline bitfld.word 0x2 1. "UPDPOS,Update Position Registers" "0: No action for POSD REV UPOS and LPOS registers..,1: Clear POSD REV UPOS and LPOS registers on rising.." bitfld.word 0x2 0. "UPDHLD,Update Hold Registers" "0: Disable updates of hold registers on the rising..,1: Enable updates of hold registers on the rising.." line.word 0x4 "UMOD,Upper Modulus Register" hexmask.word 0x4 0.--15. 1. "MOD,MOD" line.word 0x6 "LMOD,Lower Modulus Register" hexmask.word 0x6 0.--15. 1. "MOD,MOD" line.word 0x8 "UCOMP,Upper Position Compare Register" hexmask.word 0x8 0.--15. 1. "COMP,COMP" line.word 0xA "LCOMP,Lower Position Compare Register" hexmask.word 0xA 0.--15. 1. "COMP,COMP" rgroup.word 0x28++0x9 line.word 0x0 "LASTEDGE,Last Edge Time Register" hexmask.word 0x0 0.--15. 1. "LASTEDGE,Last Edge Time Counter" line.word 0x2 "LASTEDGEH,Last Edge Time Hold Register" hexmask.word 0x2 0.--15. 1. "LASTEDGEH,Last Edge Time Hold" line.word 0x4 "POSDPER,Position Difference Period Counter Register" hexmask.word 0x4 0.--15. 1. "POSDPER,Position difference period" line.word 0x6 "POSDPERBFR,Position Difference Period Buffer Register" hexmask.word 0x6 0.--15. 1. "POSDPERBFR,Position difference period buffer" line.word 0x8 "POSDPERH,Position Difference Period Hold Register" hexmask.word 0x8 0.--15. 1. "POSDPERH,Position difference period hold" group.word 0x32++0x1 line.word 0x0 "CTRL3,Control 3 Register" hexmask.word.byte 0x0 4.--7. 1. "PRSC,Prescaler" bitfld.word 0x0 0. "PMEN,Period measurement function enable" "0: Period measurement functions are not used. POSD..,1: Period measurement functions are used. POSD is.." tree.end tree "ENC4" base ad:0x40180000 group.word 0x0++0x7 line.word 0x0 "CTRL,Control Register" eventfld.word 0x0 15. "HIRQ,HOME Signal Transition Interrupt Request" "0: No transition on the HOME signal has occurred,1: A transition on the HOME signal has occurred" bitfld.word 0x0 14. "HIE,HOME Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "HIP,Enable HOME to Initialize Position Counters UPOS and LPOS" "0: No action,1: HOME signal initializes the position counter" bitfld.word 0x0 12. "HNE,Use Negative Edge of HOME Input" "0: Use positive-going edge-to-trigger..,1: Use negative-going edge-to-trigger.." newline bitfld.word 0x0 11. "SWIP,Software-Triggered Initialization of Position Counters UPOS and LPOS" "0: No action,1: Initialize position counter (using upper and.." bitfld.word 0x0 10. "REV,Enable Reverse Direction Counting" "0: Count normally,1: Count in the reverse direction" newline bitfld.word 0x0 9. "PH1,Enable Signal Phase Count Mode" "0: Use the standard quadrature decoder where PHASEA..,1: Bypass the quadrature decoder. A positive.." eventfld.word 0x0 8. "XIRQ,INDEX Pulse Interrupt Request" "0: INDEX pulse has not occurred,1: INDEX pulse has occurred" newline bitfld.word 0x0 7. "XIE,INDEX Pulse Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 6. "XIP,INDEX Triggered Initialization of Position Counters UPOS and LPOS" "0: INDEX pulse does not initialize the position..,1: INDEX pulse initializes the position counter" newline bitfld.word 0x0 5. "XNE,Use Negative Edge of INDEX Pulse" "0: Use positive edge of INDEX pulse,1: Use negative edge of INDEX pulse" eventfld.word 0x0 4. "DIRQ,Watchdog Timeout Interrupt Request" "0: No Watchdog timeout interrupt has occurred,1: Watchdog timeout interrupt has occurred" newline bitfld.word 0x0 3. "DIE,Watchdog Timeout Interrupt Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 2. "WDE,Watchdog Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x0 1. "CMPIRQ,Compare Interrupt Request" "0: No match has occurred (the counter does not..,1: COMP match has occurred (the counter matches the.." bitfld.word 0x0 0. "CMPIE,Compare Interrupt Enable" "0: Disabled,1: Enabled" line.word 0x2 "FILT,Input Filter Register" bitfld.word 0x2 13.--15. "FILT_PRSC,prescaler divide IPbus clock to FILT clk" "0,1,2,3,4,5,6,7" bitfld.word 0x2 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x2 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x4 "WTR,Watchdog Timeout Register" hexmask.word 0x4 0.--15. 1. "WDOG,WDOG" line.word 0x6 "POSD,Position Difference Counter Register" hexmask.word 0x6 0.--15. 1. "POSD,POSD" rgroup.word 0x8++0x1 line.word 0x0 "POSDH,Position Difference Hold Register" hexmask.word 0x0 0.--15. 1. "POSDH,POSDH" group.word 0xA++0x1 line.word 0x0 "REV,Revolution Counter Register" hexmask.word 0x0 0.--15. 1. "REV,REV" rgroup.word 0xC++0x1 line.word 0x0 "REVH,Revolution Hold Register" hexmask.word 0x0 0.--15. 1. "REVH,REVH" group.word 0xE++0x3 line.word 0x0 "UPOS,Upper Position Counter Register" hexmask.word 0x0 0.--15. 1. "POS,POS" line.word 0x2 "LPOS,Lower Position Counter Register" hexmask.word 0x2 0.--15. 1. "POS,POS" rgroup.word 0x12++0x3 line.word 0x0 "UPOSH,Upper Position Hold Register" hexmask.word 0x0 0.--15. 1. "POSH,POSH" line.word 0x2 "LPOSH,Lower Position Hold Register" hexmask.word 0x2 0.--15. 1. "POSH,POSH" group.word 0x16++0x3 line.word 0x0 "UINIT,Upper Initialization Register" hexmask.word 0x0 0.--15. 1. "INIT,INIT" line.word 0x2 "LINIT,Lower Initialization Register" hexmask.word 0x2 0.--15. 1. "INIT,INIT" rgroup.word 0x1A++0x1 line.word 0x0 "IMR,Input Monitor Register" bitfld.word 0x0 7. "FPHA,FPHA" "0,1" bitfld.word 0x0 6. "FPHB,FPHB" "0,1" newline bitfld.word 0x0 5. "FIND,FIND" "0,1" bitfld.word 0x0 4. "FHOM,FHOM" "0,1" newline bitfld.word 0x0 3. "PHA,PHA" "0,1" bitfld.word 0x0 2. "PHB,PHB" "0,1" newline bitfld.word 0x0 1. "INDEX,INDEX" "0,1" bitfld.word 0x0 0. "HOME,HOME" "0,1" group.word 0x1C++0xB line.word 0x0 "TST,Test Register" bitfld.word 0x0 15. "TEN,Test Mode Enable" "0: Disabled,1: Enabled" bitfld.word 0x0 14. "TCE,Test Counter Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x0 13. "QDN,Quadrature Decoder Negative Signal" "0: Generates a positive quadrature decoder signal,1: Generates a negative quadrature decoder signal" hexmask.word.byte 0x0 8.--12. 1. "TEST_PERIOD,TEST_PERIOD" newline hexmask.word.byte 0x0 0.--7. 1. "TEST_COUNT,TEST_COUNT" line.word 0x2 "CTRL2,Control 2 Register" eventfld.word 0x2 11. "SABIRQ,Simultaneous PHASEA and PHASEB Change Interrupt Request" "0: No simultaneous change of PHASEA and PHASEB has..,1: A simultaneous change of PHASEA and PHASEB has.." bitfld.word 0x2 10. "SABIE,Simultaneous PHASEA and PHASEB Change Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.word 0x2 9. "OUTCTL,Output Control" "0: POSMATCH pulses when a match occurs between the..,1: POSMATCH pulses when the UPOS LPOS REV or POSD.." bitfld.word 0x2 8. "REVMOD,Revolution Counter Modulus Enable" "0: Use INDEX pulse to increment/decrement..,1: Use modulus counting roll-over/under to.." newline eventfld.word 0x2 7. "ROIRQ,Roll-over Interrupt Request" "0: No roll-over has occurred,1: Roll-over has occurred" bitfld.word 0x2 6. "ROIE,Roll-over Interrupt Enable" "0: Disabled,1: Enabled" newline eventfld.word 0x2 5. "RUIRQ,Roll-under Interrupt Request" "0: No roll-under has occurred,1: Roll-under has occurred" bitfld.word 0x2 4. "RUIE,Roll-under Interrupt Enable" "0: Disabled,1: Enabled" newline rbitfld.word 0x2 3. "DIR,Count Direction Flag" "0: Last count was in the down direction,1: Last count was in the up direction" bitfld.word 0x2 2. "MOD,Enable Modulo Counting" "0: Disable modulo counting,1: Enable modulo counting" newline bitfld.word 0x2 1. "UPDPOS,Update Position Registers" "0: No action for POSD REV UPOS and LPOS registers..,1: Clear POSD REV UPOS and LPOS registers on rising.." bitfld.word 0x2 0. "UPDHLD,Update Hold Registers" "0: Disable updates of hold registers on the rising..,1: Enable updates of hold registers on the rising.." line.word 0x4 "UMOD,Upper Modulus Register" hexmask.word 0x4 0.--15. 1. "MOD,MOD" line.word 0x6 "LMOD,Lower Modulus Register" hexmask.word 0x6 0.--15. 1. "MOD,MOD" line.word 0x8 "UCOMP,Upper Position Compare Register" hexmask.word 0x8 0.--15. 1. "COMP,COMP" line.word 0xA "LCOMP,Lower Position Compare Register" hexmask.word 0xA 0.--15. 1. "COMP,COMP" rgroup.word 0x28++0x9 line.word 0x0 "LASTEDGE,Last Edge Time Register" hexmask.word 0x0 0.--15. 1. "LASTEDGE,Last Edge Time Counter" line.word 0x2 "LASTEDGEH,Last Edge Time Hold Register" hexmask.word 0x2 0.--15. 1. "LASTEDGEH,Last Edge Time Hold" line.word 0x4 "POSDPER,Position Difference Period Counter Register" hexmask.word 0x4 0.--15. 1. "POSDPER,Position difference period" line.word 0x6 "POSDPERBFR,Position Difference Period Buffer Register" hexmask.word 0x6 0.--15. 1. "POSDPERBFR,Position difference period buffer" line.word 0x8 "POSDPERH,Position Difference Period Hold Register" hexmask.word 0x8 0.--15. 1. "POSDPERH,Position difference period hold" group.word 0x32++0x1 line.word 0x0 "CTRL3,Control 3 Register" hexmask.word.byte 0x0 4.--7. 1. "PRSC,Prescaler" bitfld.word 0x0 0. "PMEN,Period measurement function enable" "0: Period measurement functions are not used. POSD..,1: Period measurement functions are used. POSD is.." tree.end tree.end tree "ENET" base ad:0x0 tree "ENET" base ad:0x40424000 group.long 0x4++0x7 line.long 0x0 "EIR,Interrupt Event Register" eventfld.long 0x0 30. "BABR,Babbling Receive Error" "0,1" newline eventfld.long 0x0 29. "BABT,Babbling Transmit Error" "0,1" newline eventfld.long 0x0 28. "GRA,Graceful Stop Complete" "0,1" newline eventfld.long 0x0 27. "TXF,Transmit Frame Interrupt" "0,1" newline eventfld.long 0x0 26. "TXB,Transmit Buffer Interrupt" "0,1" newline eventfld.long 0x0 25. "RXF,Receive Frame Interrupt" "0,1" newline eventfld.long 0x0 24. "RXB,Receive Buffer Interrupt" "0,1" newline eventfld.long 0x0 23. "MII,MII Interrupt." "0,1" newline eventfld.long 0x0 22. "EBERR,Ethernet Bus Error" "0,1" newline eventfld.long 0x0 21. "LC,Late Collision" "0,1" newline eventfld.long 0x0 20. "RL,Collision Retry Limit" "0,1" newline eventfld.long 0x0 19. "UN,Transmit FIFO Underrun" "0,1" newline eventfld.long 0x0 18. "PLR,Payload Receive Error" "0,1" newline eventfld.long 0x0 17. "WAKEUP,Node Wakeup Request Indication" "0,1" newline eventfld.long 0x0 16. "TS_AVAIL,Transmit Timestamp Available" "0,1" newline eventfld.long 0x0 15. "TS_TIMER,Timestamp Timer" "0,1" line.long 0x4 "EIMR,Interrupt Mask Register" bitfld.long 0x4 30. "BABR,BABR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 29. "BABT,BABT Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 28. "GRA,GRA Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 27. "TXF,TXF Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 26. "TXB,TXB Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 25. "RXF,RXF Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 24. "RXB,RXB Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 23. "MII,MII Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 22. "EBERR,EBERR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 21. "LC,LC Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 20. "RL,RL Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 19. "UN,UN Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 18. "PLR,PLR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 17. "WAKEUP,WAKEUP Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 16. "TS_AVAIL,TS_AVAIL Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 15. "TS_TIMER,TS_TIMER Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." group.long 0x10++0x7 line.long 0x0 "RDAR,Receive Descriptor Active Register - Ring 0" bitfld.long 0x0 24. "RDAR,Receive Descriptor Active" "0,1" line.long 0x4 "TDAR,Transmit Descriptor Active Register - Ring 0" bitfld.long 0x4 24. "TDAR,Transmit Descriptor Active" "0,1" group.long 0x24++0x3 line.long 0x0 "ECR,Ethernet Control Register" bitfld.long 0x0 8. "DBSWP,Descriptor Byte Swapping Enable" "0: The buffer descriptor bytes are not swapped to..,1: The buffer descriptor bytes are swapped to.." newline bitfld.long 0x0 6. "DBGEN,Debug Enable" "0: MAC continues operation in debug mode.,1: MAC enters hardware freeze mode when the.." newline bitfld.long 0x0 4. "EN1588,EN1588 Enable" "0: Legacy FEC buffer descriptors and functions..,1: Enhanced frame time-stamping functions enabled." newline bitfld.long 0x0 3. "SLEEP,Sleep Mode Enable" "0: Normal operating mode.,1: Sleep mode." newline bitfld.long 0x0 2. "MAGICEN,Magic Packet Detection Enable" "0: Magic detection logic disabled.,1: The MAC core detects magic packets and asserts.." newline bitfld.long 0x0 1. "ETHEREN,Ethernet Enable" "0: Reception immediately stops and transmission..,1: MAC is enabled and reception and transmission.." newline bitfld.long 0x0 0. "RESET,Ethernet MAC Reset" "0,1" group.long 0x40++0x7 line.long 0x0 "MMFR,MII Management Frame Register" bitfld.long 0x0 30.--31. "ST,Start Of Frame Delimiter" "0,1,2,3" newline bitfld.long 0x0 28.--29. "OP,Operation Code" "0,1,2,3" newline hexmask.long.byte 0x0 23.--27. 1. "PA,PHY Address" newline hexmask.long.byte 0x0 18.--22. 1. "RA,Register Address" newline bitfld.long 0x0 16.--17. "TA,Turn Around" "0,1,2,3" newline hexmask.long.word 0x0 0.--15. 1. "DATA,Management Frame Data" line.long 0x4 "MSCR,MII Speed Control Register" bitfld.long 0x4 8.--10. "HOLDTIME,Hold time On MDIO Output" "0: 1 internal module clock cycle,1: 2 internal module clock cycles,2: 3 internal module clock cycles,?,?,?,?,7: 8 internal module clock cycles" newline bitfld.long 0x4 7. "DIS_PRE,Disable Preamble" "0: Preamble enabled.,1: Preamble (32 ones) is not prepended to the MII.." newline hexmask.long.byte 0x4 1.--6. 1. "MII_SPEED,MII Speed" group.long 0x64++0x3 line.long 0x0 "MIBC,MIB Control Register" bitfld.long 0x0 31. "MIB_DIS,Disable MIB Logic" "0: MIB logic is enabled.,1: MIB logic is disabled. The MIB logic halts and.." newline rbitfld.long 0x0 30. "MIB_IDLE,MIB Idle" "0: The MIB block is updating MIB counters.,1: The MIB block is not currently updating any MIB.." newline bitfld.long 0x0 29. "MIB_CLEAR,MIB Clear" "0: See note above.,1: All statistics counters are reset to 0." group.long 0x84++0x3 line.long 0x0 "RCR,Receive Control Register" rbitfld.long 0x0 31. "GRS,Graceful Receive Stopped" "0: Receive not stopped,1: Receive stopped" newline bitfld.long 0x0 30. "NLC,Payload Length Check Disable" "0: The payload length check is disabled.,1: The core checks the frame's payload length with.." newline hexmask.long.word 0x0 16.--29. 1. "MAX_FL,Maximum Frame Length" newline bitfld.long 0x0 15. "CFEN,MAC Control Frame Enable" "0: MAC control frames with any opcode other than..,1: MAC control frames with any opcode other than.." newline bitfld.long 0x0 14. "CRCFWD,Terminate/Forward Received CRC" "0: The CRC field of received frames is transmitted..,1: The CRC field is stripped from the frame." newline bitfld.long 0x0 13. "PAUFWD,Terminate/Forward Pause Frames" "0: Pause frames are terminated and discarded in the..,1: Pause frames are forwarded to the user.." newline bitfld.long 0x0 12. "PADEN,Enable Frame Padding Remove On Receive" "0: No padding is removed on receive by the MAC.,1: Padding is removed from received frames." newline bitfld.long 0x0 9. "RMII_10T,Enables 10-Mbit/s mode of the RMII ." "0: 100-Mbit/s operation.,1: 10-Mbit/s operation." newline bitfld.long 0x0 8. "RMII_MODE,RMII Mode Enable" "0: MAC configured for MII mode.,1: MAC configured for RMII operation." newline bitfld.long 0x0 5. "FCE,Flow Control Enable" "0: Disable flow control,1: Enable flow control" newline bitfld.long 0x0 4. "BC_REJ,Broadcast Frame Reject" "0: Will not reject frames as described above,1: Will reject frames as described above" newline bitfld.long 0x0 3. "PROM,Promiscuous Mode" "0: Disabled.,1: Enabled." newline bitfld.long 0x0 2. "MII_MODE,Media Independent Interface Mode" "?,1: MII or RMII mode as indicated by the RMII_MODE.." newline bitfld.long 0x0 1. "DRT,Disable Receive On Transmit" "0: Receive path operates independently of transmit..,1: Disable reception of frames while transmitting." newline bitfld.long 0x0 0. "LOOP,Internal Loopback" "0: Loopback disabled.,1: Transmitted frames are looped back internal to.." group.long 0xC4++0x3 line.long 0x0 "TCR,Transmit Control Register" bitfld.long 0x0 9. "CRCFWD,Forward Frame From Application With CRC" "0: TxBD[TC] controls whether the frame has a CRC..,1: The transmitter does not append any CRC to.." newline bitfld.long 0x0 8. "ADDINS,Set MAC Address On Transmit" "0: The source MAC address is not modified by the MAC.,1: The MAC overwrites the source MAC address with.." newline bitfld.long 0x0 5.--7. "ADDSEL,Source MAC Address Select On Transmit" "0: Node MAC address programmed on PADDR1/2 registers.,?,?,?,?,?,?,?" newline rbitfld.long 0x0 4. "RFC_PAUSE,Receive Frame Control Pause" "0,1" newline bitfld.long 0x0 3. "TFC_PAUSE,Transmit Frame Control Pause" "0: No PAUSE frame transmitted.,1: The MAC stops transmission of data frames after.." newline bitfld.long 0x0 2. "FDEN,Full-Duplex Enable" "0: Disable full-duplex,1: Enable full-duplex" newline bitfld.long 0x0 0. "GTS,Graceful Transmit Stop" "0: Disable graceful transmit stop,1: Enable graceful transmit stop" group.long 0xE4++0xB line.long 0x0 "PALR,Physical Address Lower Register" hexmask.long 0x0 0.--31. 1. "PADDR1,Pause Address" line.long 0x4 "PAUR,Physical Address Upper Register" hexmask.long.word 0x4 16.--31. 1. "PADDR2,Bytes 4 (bits 31:24) and 5 (bits 23:16) of the 6-byte individual address used for exact match and the source address field in PAUSE frames" newline hexmask.long.word 0x4 0.--15. 1. "TYPE,Type Field In PAUSE Frames" line.long 0x8 "OPD,Opcode/Pause Duration Register" hexmask.long.word 0x8 16.--31. 1. "OPCODE,Opcode Field In PAUSE Frames" newline hexmask.long.word 0x8 0.--15. 1. "PAUSE_DUR,Pause Duration" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xF0)++0x3 line.long 0x0 "TXIC[$1],Transmit Interrupt Coalescing Register" bitfld.long 0x0 31. "ICEN,Interrupt Coalescing Enable" "0: Disable Interrupt coalescing.,1: Enable Interrupt coalescing." newline bitfld.long 0x0 30. "ICCS,Interrupt Coalescing Timer Clock Source Select" "0: Use MII/GMII TX clocks.,1: Use ENET system clock." newline hexmask.long.byte 0x0 20.--27. 1. "ICFT,Interrupt coalescing frame count threshold" newline hexmask.long.word 0x0 0.--15. 1. "ICTT,Interrupt coalescing timer threshold" repeat.end repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x100)++0x3 line.long 0x0 "RXIC[$1],Receive Interrupt Coalescing Register" bitfld.long 0x0 31. "ICEN,Interrupt Coalescing Enable" "0: Disable Interrupt coalescing.,1: Enable Interrupt coalescing." newline bitfld.long 0x0 30. "ICCS,Interrupt Coalescing Timer Clock Source Select" "0: Use MII/GMII TX clocks.,1: Use ENET system clock." newline hexmask.long.byte 0x0 20.--27. 1. "ICFT,Interrupt coalescing frame count threshold" newline hexmask.long.word 0x0 0.--15. 1. "ICTT,Interrupt coalescing timer threshold" repeat.end group.long 0x118++0xF line.long 0x0 "IAUR,Descriptor Individual Upper Address Register" hexmask.long 0x0 0.--31. 1. "IADDR1,Contains the upper 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a unicast address" line.long 0x4 "IALR,Descriptor Individual Lower Address Register" hexmask.long 0x4 0.--31. 1. "IADDR2,Contains the lower 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a unicast address" line.long 0x8 "GAUR,Descriptor Group Upper Address Register" hexmask.long 0x8 0.--31. 1. "GADDR1,Contains the upper 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a multicast address" line.long 0xC "GALR,Descriptor Group Lower Address Register" hexmask.long 0xC 0.--31. 1. "GADDR2,Contains the lower 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a multicast address" group.long 0x144++0x3 line.long 0x0 "TFWR,Transmit FIFO Watermark Register" bitfld.long 0x0 8. "STRFWD,Store And Forward Enable" "0: Reset. The transmission start threshold is..,1: Enabled." newline hexmask.long.byte 0x0 0.--5. 1. "TFWR,Transmit FIFO Write" group.long 0x180++0xB line.long 0x0 "RDSR,Receive Descriptor Ring 0 Start Register" hexmask.long 0x0 3.--31. 1. "R_DES_START,Pointer to the beginning of the receive buffer descriptor queue." line.long 0x4 "TDSR,Transmit Buffer Descriptor Ring 0 Start Register" hexmask.long 0x4 3.--31. 1. "X_DES_START,Pointer to the beginning of the transmit buffer descriptor queue." line.long 0x8 "MRBR,Maximum Receive Buffer Size Register - Ring 0" hexmask.long.word 0x8 4.--13. 1. "R_BUF_SIZE,Receive buffer size in bytes" group.long 0x190++0x23 line.long 0x0 "RSFL,Receive FIFO Section Full Threshold" hexmask.long.byte 0x0 0.--7. 1. "RX_SECTION_FULL,Value Of Receive FIFO Section Full Threshold" line.long 0x4 "RSEM,Receive FIFO Section Empty Threshold" hexmask.long.byte 0x4 16.--20. 1. "STAT_SECTION_EMPTY,RX Status FIFO Section Empty Threshold" newline hexmask.long.byte 0x4 0.--7. 1. "RX_SECTION_EMPTY,Value Of The Receive FIFO Section Empty Threshold" line.long 0x8 "RAEM,Receive FIFO Almost Empty Threshold" hexmask.long.byte 0x8 0.--7. 1. "RX_ALMOST_EMPTY,Value Of The Receive FIFO Almost Empty Threshold" line.long 0xC "RAFL,Receive FIFO Almost Full Threshold" hexmask.long.byte 0xC 0.--7. 1. "RX_ALMOST_FULL,Value Of The Receive FIFO Almost Full Threshold" line.long 0x10 "TSEM,Transmit FIFO Section Empty Threshold" hexmask.long.byte 0x10 0.--7. 1. "TX_SECTION_EMPTY,Value Of The Transmit FIFO Section Empty Threshold" line.long 0x14 "TAEM,Transmit FIFO Almost Empty Threshold" hexmask.long.byte 0x14 0.--7. 1. "TX_ALMOST_EMPTY,Value of Transmit FIFO Almost Empty Threshold" line.long 0x18 "TAFL,Transmit FIFO Almost Full Threshold" hexmask.long.byte 0x18 0.--7. 1. "TX_ALMOST_FULL,Value Of The Transmit FIFO Almost Full Threshold" line.long 0x1C "TIPG,Transmit Inter-Packet Gap" hexmask.long.byte 0x1C 0.--4. 1. "IPG,Transmit Inter-Packet Gap" line.long 0x20 "FTRL,Frame Truncation Length" hexmask.long.word 0x20 0.--13. 1. "TRUNC_FL,Frame Truncation Length" group.long 0x1C0++0x7 line.long 0x0 "TACC,Transmit Accelerator Function Configuration" bitfld.long 0x0 4. "PROCHK,Enables insertion of protocol checksum." "0: Checksum not inserted.,1: If an IP frame with a known protocol is.." newline bitfld.long 0x0 3. "IPCHK,Enables insertion of IP header checksum." "0: Checksum is not inserted.,1: If an IP frame is transmitted the checksum is.." newline bitfld.long 0x0 0. "SHIFT16,TX FIFO Shift-16" "0: Disabled.,1: Indicates to the transmit data FIFO that the.." line.long 0x4 "RACC,Receive Accelerator Function Configuration" bitfld.long 0x4 7. "SHIFT16,RX FIFO Shift-16" "0: Disabled.,1: Instructs the MAC to write two additional bytes.." newline bitfld.long 0x4 6. "LINEDIS,Enable Discard Of Frames With MAC Layer Errors" "0: Frames with errors are not discarded.,1: Any frame received with a CRC length or PHY.." newline bitfld.long 0x4 2. "PRODIS,Enable Discard Of Frames With Wrong Protocol Checksum" "0: Frames with wrong checksum are not discarded.,1: If a TCP/IP UDP/IP or ICMP/IP frame is received.." newline bitfld.long 0x4 1. "IPDIS,Enable Discard Of Frames With Wrong IPv4 Header Checksum" "0: Frames with wrong IPv4 header checksum are not..,1: If an IPv4 frame is received with a mismatching.." newline bitfld.long 0x4 0. "PADREM,Enable Padding Removal For Short IP Frames" "0: Padding not removed.,1: Any bytes following the IP payload section of.." rgroup.long 0x204++0x73 line.long 0x0 "RMON_T_PACKETS,Tx Packet Count Statistic Register" hexmask.long.word 0x0 0.--15. 1. "TXPKTS,Packet count" line.long 0x4 "RMON_T_BC_PKT,Tx Broadcast Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "TXPKTS,Broadcast packets" line.long 0x8 "RMON_T_MC_PKT,Tx Multicast Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "TXPKTS,Multicast packets" line.long 0xC "RMON_T_CRC_ALIGN,Tx Packets with CRC/Align Error Statistic Register" hexmask.long.word 0xC 0.--15. 1. "TXPKTS,Packets with CRC/align error" line.long 0x10 "RMON_T_UNDERSIZE,Tx Packets Less Than Bytes and Good CRC Statistic Register" hexmask.long.word 0x10 0.--15. 1. "TXPKTS,Number of transmit packets less than 64 bytes with good CRC" line.long 0x14 "RMON_T_OVERSIZE,Tx Packets GT MAX_FL bytes and Good CRC Statistic Register" hexmask.long.word 0x14 0.--15. 1. "TXPKTS,Number of transmit packets greater than MAX_FL bytes with good CRC" line.long 0x18 "RMON_T_FRAG,Tx Packets Less Than 64 Bytes and Bad CRC Statistic Register" hexmask.long.word 0x18 0.--15. 1. "TXPKTS,Number of packets less than 64 bytes with bad CRC" line.long 0x1C "RMON_T_JAB,Tx Packets Greater Than MAX_FL bytes and Bad CRC Statistic Register" hexmask.long.word 0x1C 0.--15. 1. "TXPKTS,Number of transmit packets greater than MAX_FL bytes and bad CRC" line.long 0x20 "RMON_T_COL,Tx Collision Count Statistic Register" hexmask.long.word 0x20 0.--15. 1. "TXPKTS,Number of transmit collisions" line.long 0x24 "RMON_T_P64,Tx 64-Byte Packets Statistic Register" hexmask.long.word 0x24 0.--15. 1. "TXPKTS,Number of 64-byte transmit packets" line.long 0x28 "RMON_T_P65TO127,Tx 65- to 127-byte Packets Statistic Register" hexmask.long.word 0x28 0.--15. 1. "TXPKTS,Number of 65- to 127-byte transmit packets" line.long 0x2C "RMON_T_P128TO255,Tx 128- to 255-byte Packets Statistic Register" hexmask.long.word 0x2C 0.--15. 1. "TXPKTS,Number of 128- to 255-byte transmit packets" line.long 0x30 "RMON_T_P256TO511,Tx 256- to 511-byte Packets Statistic Register" hexmask.long.word 0x30 0.--15. 1. "TXPKTS,Number of 256- to 511-byte transmit packets" line.long 0x34 "RMON_T_P512TO1023,Tx 512- to 1023-byte Packets Statistic Register" hexmask.long.word 0x34 0.--15. 1. "TXPKTS,Number of 512- to 1023-byte transmit packets" line.long 0x38 "RMON_T_P1024TO2047,Tx 1024- to 2047-byte Packets Statistic Register" hexmask.long.word 0x38 0.--15. 1. "TXPKTS,Number of 1024- to 2047-byte transmit packets" line.long 0x3C "RMON_T_P_GTE2048,Tx Packets Greater Than 2048 Bytes Statistic Register" hexmask.long.word 0x3C 0.--15. 1. "TXPKTS,Number of transmit packets greater than 2048 bytes" line.long 0x40 "RMON_T_OCTETS,Tx Octets Statistic Register" hexmask.long 0x40 0.--31. 1. "TXOCTS,Number of transmit octets" line.long 0x44 "IEEE_T_DROP,Reserved Statistic Register" line.long 0x48 "IEEE_T_FRAME_OK,Frames Transmitted OK Statistic Register" hexmask.long.word 0x48 0.--15. 1. "COUNT,Number of frames transmitted OK" line.long 0x4C "IEEE_T_1COL,Frames Transmitted with Single Collision Statistic Register" hexmask.long.word 0x4C 0.--15. 1. "COUNT,Number of frames transmitted with one collision" line.long 0x50 "IEEE_T_MCOL,Frames Transmitted with Multiple Collisions Statistic Register" hexmask.long.word 0x50 0.--15. 1. "COUNT,Number of frames transmitted with multiple collisions" line.long 0x54 "IEEE_T_DEF,Frames Transmitted after Deferral Delay Statistic Register" hexmask.long.word 0x54 0.--15. 1. "COUNT,Number of frames transmitted with deferral delay" line.long 0x58 "IEEE_T_LCOL,Frames Transmitted with Late Collision Statistic Register" hexmask.long.word 0x58 0.--15. 1. "COUNT,Number of frames transmitted with late collision" line.long 0x5C "IEEE_T_EXCOL,Frames Transmitted with Excessive Collisions Statistic Register" hexmask.long.word 0x5C 0.--15. 1. "COUNT,Number of frames transmitted with excessive collisions" line.long 0x60 "IEEE_T_MACERR,Frames Transmitted with Tx FIFO Underrun Statistic Register" hexmask.long.word 0x60 0.--15. 1. "COUNT,Number of frames transmitted with transmit FIFO underrun" line.long 0x64 "IEEE_T_CSERR,Frames Transmitted with Carrier Sense Error Statistic Register" hexmask.long.word 0x64 0.--15. 1. "COUNT,Number of frames transmitted with carrier sense error" line.long 0x68 "IEEE_T_SQE,Reserved Statistic Register" hexmask.long.word 0x68 0.--15. 1. "COUNT,This read-only field is reserved and always has the value 0" line.long 0x6C "IEEE_T_FDXFC,Flow Control Pause Frames Transmitted Statistic Register" hexmask.long.word 0x6C 0.--15. 1. "COUNT,Number of flow-control pause frames transmitted" line.long 0x70 "IEEE_T_OCTETS_OK,Octet Count for Frames Transmitted w/o Error Statistic Register" hexmask.long 0x70 0.--31. 1. "COUNT,Octet count for frames transmitted without error Counts total octets (includes header and FCS fields)." rgroup.long 0x284++0x1F line.long 0x0 "RMON_R_PACKETS,Rx Packet Count Statistic Register" hexmask.long.word 0x0 0.--15. 1. "COUNT,Number of packets received" line.long 0x4 "RMON_R_BC_PKT,Rx Broadcast Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "COUNT,Number of receive broadcast packets" line.long 0x8 "RMON_R_MC_PKT,Rx Multicast Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "COUNT,Number of receive multicast packets" line.long 0xC "RMON_R_CRC_ALIGN,Rx Packets with CRC/Align Error Statistic Register" hexmask.long.word 0xC 0.--15. 1. "COUNT,Number of receive packets with CRC or align error" line.long 0x10 "RMON_R_UNDERSIZE,Rx Packets with Less Than 64 Bytes and Good CRC Statistic Register" hexmask.long.word 0x10 0.--15. 1. "COUNT,Number of receive packets with less than 64 bytes and good CRC" line.long 0x14 "RMON_R_OVERSIZE,Rx Packets Greater Than MAX_FL and Good CRC Statistic Register" hexmask.long.word 0x14 0.--15. 1. "COUNT,Number of receive packets greater than MAX_FL and good CRC" line.long 0x18 "RMON_R_FRAG,Rx Packets Less Than 64 Bytes and Bad CRC Statistic Register" hexmask.long.word 0x18 0.--15. 1. "COUNT,Number of receive packets with less than 64 bytes and bad CRC" line.long 0x1C "RMON_R_JAB,Rx Packets Greater Than MAX_FL Bytes and Bad CRC Statistic Register" hexmask.long.word 0x1C 0.--15. 1. "COUNT,Number of receive packets greater than MAX_FL and bad CRC" rgroup.long 0x2A8++0x3B line.long 0x0 "RMON_R_P64,Rx 64-Byte Packets Statistic Register" hexmask.long.word 0x0 0.--15. 1. "COUNT,Number of 64-byte receive packets" line.long 0x4 "RMON_R_P65TO127,Rx 65- to 127-Byte Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "COUNT,Number of 65- to 127-byte recieve packets" line.long 0x8 "RMON_R_P128TO255,Rx 128- to 255-Byte Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "COUNT,Number of 128- to 255-byte recieve packets" line.long 0xC "RMON_R_P256TO511,Rx 256- to 511-Byte Packets Statistic Register" hexmask.long.word 0xC 0.--15. 1. "COUNT,Number of 256- to 511-byte recieve packets" line.long 0x10 "RMON_R_P512TO1023,Rx 512- to 1023-Byte Packets Statistic Register" hexmask.long.word 0x10 0.--15. 1. "COUNT,Number of 512- to 1023-byte recieve packets" line.long 0x14 "RMON_R_P1024TO2047,Rx 1024- to 2047-Byte Packets Statistic Register" hexmask.long.word 0x14 0.--15. 1. "COUNT,Number of 1024- to 2047-byte recieve packets" line.long 0x18 "RMON_R_P_GTE2048,Rx Packets Greater than 2048 Bytes Statistic Register" hexmask.long.word 0x18 0.--15. 1. "COUNT,Number of greater-than-2048-byte recieve packets" line.long 0x1C "RMON_R_OCTETS,Rx Octets Statistic Register" hexmask.long 0x1C 0.--31. 1. "COUNT,Number of receive octets" line.long 0x20 "IEEE_R_DROP,Frames not Counted Correctly Statistic Register" hexmask.long.word 0x20 0.--15. 1. "COUNT,Frame count" line.long 0x24 "IEEE_R_FRAME_OK,Frames Received OK Statistic Register" hexmask.long.word 0x24 0.--15. 1. "COUNT,Number of frames received OK" line.long 0x28 "IEEE_R_CRC,Frames Received with CRC Error Statistic Register" hexmask.long.word 0x28 0.--15. 1. "COUNT,Number of frames received with CRC error" line.long 0x2C "IEEE_R_ALIGN,Frames Received with Alignment Error Statistic Register" hexmask.long.word 0x2C 0.--15. 1. "COUNT,Number of frames received with alignment error" line.long 0x30 "IEEE_R_MACERR,Receive FIFO Overflow Count Statistic Register" hexmask.long.word 0x30 0.--15. 1. "COUNT,Receive FIFO overflow count" line.long 0x34 "IEEE_R_FDXFC,Flow Control Pause Frames Received Statistic Register" hexmask.long.word 0x34 0.--15. 1. "COUNT,Number of flow-control pause frames received" line.long 0x38 "IEEE_R_OCTETS_OK,Octet Count for Frames Received without Error Statistic Register" hexmask.long 0x38 0.--31. 1. "COUNT,Number of octets for frames received without error" group.long 0x400++0x17 line.long 0x0 "ATCR,Adjustable Timer Control Register" bitfld.long 0x0 13. "SLAVE,Enable Timer Slave Mode" "0: The timer is active and all configuration fields..,1: The internal timer is disabled and the.." newline bitfld.long 0x0 11. "CAPTURE,Capture Timer Value" "0: No effect.,1: The current time is captured and can be read.." newline bitfld.long 0x0 9. "RESTART,Reset Timer" "0,1" newline bitfld.long 0x0 7. "PINPER,Enables event signal output external pin frc_evt_period assertion on period event" "0: Disable.,1: Enable." newline bitfld.long 0x0 4. "PEREN,Enable Periodical Event" "0: Disable.,1: A period event interrupt can be generated.." newline bitfld.long 0x0 3. "OFFRST,Reset Timer On Offset Event" "0: The timer is not affected and no action occurs..,1: If OFFEN is set the timer resets to zero when.." newline bitfld.long 0x0 2. "OFFEN,Enable One-Shot Offset Event" "0: Disable.,1: The timer can be reset to zero when the given.." newline bitfld.long 0x0 0. "EN,Enable Timer" "0: The timer stops at the current value.,1: The timer starts incrementing." line.long 0x4 "ATVR,Timer Value Register" hexmask.long 0x4 0.--31. 1. "ATIME,A write sets the timer" line.long 0x8 "ATOFF,Timer Offset Register" hexmask.long 0x8 0.--31. 1. "OFFSET,Offset value for one-shot event generation" line.long 0xC "ATPER,Timer Period Register" hexmask.long 0xC 0.--31. 1. "PERIOD,Value for generating periodic events" line.long 0x10 "ATCOR,Timer Correction Register" hexmask.long 0x10 0.--30. 1. "COR,Correction Counter Wrap-Around Value" line.long 0x14 "ATINC,Time-Stamping Clock Period Register" hexmask.long.byte 0x14 8.--14. 1. "INC_CORR,Correction Increment Value" newline hexmask.long.byte 0x14 0.--6. 1. "INC,Clock Period Of The Timestamping Clock (ts_clk) In Nanoseconds" rgroup.long 0x418++0x3 line.long 0x0 "ATSTMP,Timestamp of Last Transmitted Frame" hexmask.long 0x0 0.--31. 1. "TIMESTAMP,Timestamp of the last frame transmitted by the core that had TxBD[TS] set the ff_tx_ts_frm signal asserted from the user application" group.long 0x604++0x23 line.long 0x0 "TGSR,Timer Global Status Register" eventfld.long 0x0 3. "TF3,Copy Of Timer Flag For Channel 3" "0: Timer Flag for Channel 3 is clear,1: Timer Flag for Channel 3 is set" newline eventfld.long 0x0 2. "TF2,Copy Of Timer Flag For Channel 2" "0: Timer Flag for Channel 2 is clear,1: Timer Flag for Channel 2 is set" newline eventfld.long 0x0 1. "TF1,Copy Of Timer Flag For Channel 1" "0: Timer Flag for Channel 1 is clear,1: Timer Flag for Channel 1 is set" newline eventfld.long 0x0 0. "TF0,Copy Of Timer Flag For Channel 0" "0: Timer Flag for Channel 0 is clear,1: Timer Flag for Channel 0 is set" line.long 0x4 "TCSR0,Timer Control Status Register" hexmask.long.byte 0x4 11.--15. 1. "TPWC,Timer PulseWidth Control" newline eventfld.long 0x4 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x4 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x4 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x4 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x8 "TCCR0,Timer Compare Capture Register" hexmask.long 0x8 0.--31. 1. "TCC,Timer Capture Compare" line.long 0xC "TCSR1,Timer Control Status Register" hexmask.long.byte 0xC 11.--15. 1. "TPWC,Timer PulseWidth Control" newline eventfld.long 0xC 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0xC 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0xC 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0xC 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "TCCR1,Timer Compare Capture Register" hexmask.long 0x10 0.--31. 1. "TCC,Timer Capture Compare" line.long 0x14 "TCSR2,Timer Control Status Register" hexmask.long.byte 0x14 11.--15. 1. "TPWC,Timer PulseWidth Control" newline eventfld.long 0x14 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x14 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x14 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x14 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x18 "TCCR2,Timer Compare Capture Register" hexmask.long 0x18 0.--31. 1. "TCC,Timer Capture Compare" line.long 0x1C "TCSR3,Timer Control Status Register" hexmask.long.byte 0x1C 11.--15. 1. "TPWC,Timer PulseWidth Control" newline eventfld.long 0x1C 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x1C 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x1C 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x1C 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x20 "TCCR3,Timer Compare Capture Register" hexmask.long 0x20 0.--31. 1. "TCC,Timer Capture Compare" tree.end tree "ENET_1G" base ad:0x40420000 group.long 0x4++0x7 line.long 0x0 "EIR,Interrupt Event Register" eventfld.long 0x0 30. "BABR,Babbling Receive Error" "0,1" newline eventfld.long 0x0 29. "BABT,Babbling Transmit Error" "0,1" newline eventfld.long 0x0 28. "GRA,Graceful Stop Complete" "0,1" newline eventfld.long 0x0 27. "TXF,Transmit Frame Interrupt" "0,1" newline eventfld.long 0x0 26. "TXB,Transmit Buffer Interrupt" "0,1" newline eventfld.long 0x0 25. "RXF,Receive Frame Interrupt" "0,1" newline eventfld.long 0x0 24. "RXB,Receive Buffer Interrupt" "0,1" newline eventfld.long 0x0 23. "MII,MII Interrupt." "0,1" newline eventfld.long 0x0 22. "EBERR,Ethernet Bus Error" "0,1" newline eventfld.long 0x0 21. "LC,Late Collision" "0,1" newline eventfld.long 0x0 20. "RL,Collision Retry Limit" "0,1" newline eventfld.long 0x0 19. "UN,Transmit FIFO Underrun" "0,1" newline eventfld.long 0x0 18. "PLR,Payload Receive Error" "0,1" newline eventfld.long 0x0 17. "WAKEUP,Node Wakeup Request Indication" "0,1" newline eventfld.long 0x0 16. "TS_AVAIL,Transmit Timestamp Available" "0,1" newline eventfld.long 0x0 15. "TS_TIMER,Timestamp Timer" "0,1" newline eventfld.long 0x0 14. "RXFLUSH_2,RX DMA Ring 2 flush indication" "0,1" newline eventfld.long 0x0 13. "RXFLUSH_1,RX DMA Ring 1 flush indication" "0,1" newline eventfld.long 0x0 12. "RXFLUSH_0,RX DMA Ring 0 flush indication" "0,1" newline eventfld.long 0x0 7. "TXF2,Transmit frame interrupt class 2" "0,1" newline eventfld.long 0x0 6. "TXB2,Transmit buffer interrupt class 2" "0,1" newline eventfld.long 0x0 5. "RXF2,Receive frame interrupt class 2" "0,1" newline eventfld.long 0x0 4. "RXB2,Receive buffer interrupt class 2" "0,1" newline eventfld.long 0x0 3. "TXF1,Transmit frame interrupt class 1" "0,1" newline eventfld.long 0x0 2. "TXB1,Transmit buffer interrupt class 1" "0,1" newline eventfld.long 0x0 1. "RXF1,Receive frame interrupt class 1" "0,1" newline eventfld.long 0x0 0. "RXB1,Receive buffer interrupt class 1" "0,1" line.long 0x4 "EIMR,Interrupt Mask Register" bitfld.long 0x4 30. "BABR,BABR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 29. "BABT,BABT Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 28. "GRA,GRA Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 27. "TXF,TXF Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 26. "TXB,TXB Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 25. "RXF,RXF Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 24. "RXB,RXB Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 23. "MII,MII Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 22. "EBERR,EBERR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 21. "LC,LC Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 20. "RL,RL Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 19. "UN,UN Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 18. "PLR,PLR Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 17. "WAKEUP,WAKEUP Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 16. "TS_AVAIL,TS_AVAIL Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 15. "TS_TIMER,TS_TIMER Interrupt Mask" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 14. "RXFLUSH_2,Corresponds to interrupt source EIR[RXFLUSH_2] and determines whether an interrupt condition can generate an interrupt" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 13. "RXFLUSH_1,Corresponds to interrupt source EIR[RXFLUSH_1] and determines whether an interrupt condition can generate an interrupt" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 12. "RXFLUSH_0,Corresponds to interrupt source EIR[RXFLUSH_0] and determines whether an interrupt condition can generate an interrupt" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 7. "TXF2,Transmit frame interrupt class 2" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 6. "TXB2,Transmit buffer interrupt class 2" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 5. "RXF2,Receive frame interrupt class 2" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 4. "RXB2,Receive buffer interrupt class 2" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 3. "TXF1,Transmit frame interrupt class 1" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 2. "TXB1,Transmit buffer interrupt class 1" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 1. "RXF1,Receive frame interrupt class 1" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." newline bitfld.long 0x4 0. "RXB1,Receive buffer interrupt class 1" "0: The corresponding interrupt source is masked.,1: The corresponding interrupt source is not masked." group.long 0x10++0x7 line.long 0x0 "RDAR,Receive Descriptor Active Register - Ring 0" bitfld.long 0x0 24. "RDAR,Receive Descriptor Active" "0,1" line.long 0x4 "TDAR,Transmit Descriptor Active Register - Ring 0" bitfld.long 0x4 24. "TDAR,Transmit Descriptor Active" "0,1" group.long 0x24++0x3 line.long 0x0 "ECR,Ethernet Control Register" bitfld.long 0x0 16. "TXC_DLY,Transmit clock delay" "0: RGMII_TXC is not delayed.,1: Generate delayed version of RGMII_TXC." newline bitfld.long 0x0 11. "SVLANDBL,S-VLAN double tag" "0: Disable S-VLAN double tag,1: Enable S-VLAN double tag" newline bitfld.long 0x0 10. "VLANUSE2ND,VLAN use second tag" "0: Always extract data from the first VLAN tag if..,1: When a double-tagged frame is detected the data.." newline bitfld.long 0x0 9. "SVLANEN,S-VLAN enable" "0: Only the EtherType 0x8100 will be considered for..,1: The EtherType 0x88a8 will be considered in.." newline bitfld.long 0x0 8. "DBSWP,Descriptor Byte Swapping Enable" "0: The buffer descriptor bytes are not swapped to..,1: The buffer descriptor bytes are swapped to.." newline bitfld.long 0x0 6. "DBGEN,Debug Enable" "0: MAC continues operation in debug mode.,1: MAC enters hardware freeze mode when the.." newline bitfld.long 0x0 5. "SPEED,Selects between 10/100-Mbit/s and 1000-Mbit/s modes of operation." "0: 10/100-Mbit/s mode,1: 1000-Mbit/s mode" newline bitfld.long 0x0 4. "EN1588,EN1588 Enable" "0: Legacy FEC buffer descriptors and functions..,1: Enhanced frame time-stamping functions enabled." newline bitfld.long 0x0 3. "SLEEP,Sleep Mode Enable" "0: Normal operating mode.,1: Sleep mode." newline bitfld.long 0x0 2. "MAGICEN,Magic Packet Detection Enable" "0: Magic detection logic disabled.,1: The MAC core detects magic packets and asserts.." newline bitfld.long 0x0 1. "ETHEREN,Ethernet Enable" "0: Reception immediately stops and transmission..,1: MAC is enabled and reception and transmission.." newline bitfld.long 0x0 0. "RESET,Ethernet MAC Reset" "0,1" group.long 0x40++0x7 line.long 0x0 "MMFR,MII Management Frame Register" bitfld.long 0x0 30.--31. "ST,Start Of Frame Delimiter" "0,1,2,3" newline bitfld.long 0x0 28.--29. "OP,Operation Code" "0,1,2,3" newline hexmask.long.byte 0x0 23.--27. 1. "PA,PHY Address" newline hexmask.long.byte 0x0 18.--22. 1. "RA,Register Address" newline bitfld.long 0x0 16.--17. "TA,Turn Around" "0,1,2,3" newline hexmask.long.word 0x0 0.--15. 1. "DATA,Management Frame Data" line.long 0x4 "MSCR,MII Speed Control Register" bitfld.long 0x4 8.--10. "HOLDTIME,Hold time On MDIO Output" "0: 1 internal module clock cycle,1: 2 internal module clock cycles,2: 3 internal module clock cycles,?,?,?,?,7: 8 internal module clock cycles" newline bitfld.long 0x4 7. "DIS_PRE,Disable Preamble" "0: Preamble enabled.,1: Preamble (32 ones) is not prepended to the MII.." newline hexmask.long.byte 0x4 1.--6. 1. "MII_SPEED,MII Speed" group.long 0x64++0x3 line.long 0x0 "MIBC,MIB Control Register" bitfld.long 0x0 31. "MIB_DIS,Disable MIB Logic" "0: MIB logic is enabled.,1: MIB logic is disabled. The MIB logic halts and.." newline rbitfld.long 0x0 30. "MIB_IDLE,MIB Idle" "0: The MIB block is updating MIB counters.,1: The MIB block is not currently updating any MIB.." newline bitfld.long 0x0 29. "MIB_CLEAR,MIB Clear" "0: See note above.,1: All statistics counters are reset to 0." group.long 0x84++0x3 line.long 0x0 "RCR,Receive Control Register" rbitfld.long 0x0 31. "GRS,Graceful Receive Stopped" "0: Receive not stopped,1: Receive stopped" newline bitfld.long 0x0 30. "NLC,Payload Length Check Disable" "0: The payload length check is disabled.,1: The core checks the frame's payload length with.." newline hexmask.long.word 0x0 16.--29. 1. "MAX_FL,Maximum Frame Length" newline bitfld.long 0x0 15. "CFEN,MAC Control Frame Enable" "0: MAC control frames with any opcode other than..,1: MAC control frames with any opcode other than.." newline bitfld.long 0x0 14. "CRCFWD,Terminate/Forward Received CRC" "0: The CRC field of received frames is transmitted..,1: The CRC field is stripped from the frame." newline bitfld.long 0x0 13. "PAUFWD,Terminate/Forward Pause Frames" "0: Pause frames are terminated and discarded in the..,1: Pause frames are forwarded to the user.." newline bitfld.long 0x0 12. "PADEN,Enable Frame Padding Remove On Receive" "0: No padding is removed on receive by the MAC.,1: Padding is removed from received frames." newline bitfld.long 0x0 9. "RMII_10T,Enables 10-Mbit/s mode of the RMII or RGMII ." "0: 100-Mbit/s or 1-Gbit/s operation.,1: 10-Mbit/s operation." newline bitfld.long 0x0 8. "RMII_MODE,RMII Mode Enable" "0: MAC configured for MII mode.,1: MAC configured for RMII operation." newline bitfld.long 0x0 6. "RGMII_EN,RGMII Mode Enable" "0: MAC configured for non-RGMII operation,1: MAC configured for RGMII operation. If.." newline bitfld.long 0x0 5. "FCE,Flow Control Enable" "0: Disable flow control,1: Enable flow control" newline bitfld.long 0x0 4. "BC_REJ,Broadcast Frame Reject" "0: Will not reject frames as described above,1: Will reject frames as described above" newline bitfld.long 0x0 3. "PROM,Promiscuous Mode" "0: Disabled.,1: Enabled." newline bitfld.long 0x0 2. "MII_MODE,Media Independent Interface Mode" "?,1: MII or RMII mode as indicated by the RMII_MODE.." newline bitfld.long 0x0 1. "DRT,Disable Receive On Transmit" "0: Receive path operates independently of transmit..,1: Disable reception of frames while transmitting." newline bitfld.long 0x0 0. "LOOP,Internal Loopback" "0: Loopback disabled.,1: Transmitted frames are looped back internal to.." group.long 0xC4++0x3 line.long 0x0 "TCR,Transmit Control Register" bitfld.long 0x0 9. "CRCFWD,Forward Frame From Application With CRC" "0: TxBD[TC] controls whether the frame has a CRC..,1: The transmitter does not append any CRC to.." newline bitfld.long 0x0 8. "ADDINS,Set MAC Address On Transmit" "0: The source MAC address is not modified by the MAC.,1: The MAC overwrites the source MAC address with.." newline bitfld.long 0x0 5.--7. "ADDSEL,Source MAC Address Select On Transmit" "0: Node MAC address programmed on PADDR1/2 registers.,?,?,?,?,?,?,?" newline rbitfld.long 0x0 4. "RFC_PAUSE,Receive Frame Control Pause" "0,1" newline bitfld.long 0x0 3. "TFC_PAUSE,Transmit Frame Control Pause" "0: No PAUSE frame transmitted.,1: The MAC stops transmission of data frames after.." newline bitfld.long 0x0 2. "FDEN,Full-Duplex Enable" "0: Disable full-duplex,1: Enable full-duplex" newline bitfld.long 0x0 0. "GTS,Graceful Transmit Stop" "0: Disable graceful transmit stop,1: Enable graceful transmit stop" group.long 0xE4++0xB line.long 0x0 "PALR,Physical Address Lower Register" hexmask.long 0x0 0.--31. 1. "PADDR1,Pause Address" line.long 0x4 "PAUR,Physical Address Upper Register" hexmask.long.word 0x4 16.--31. 1. "PADDR2,Bytes 4 (bits 31:24) and 5 (bits 23:16) of the 6-byte individual address used for exact match and the source address field in PAUSE frames" newline hexmask.long.word 0x4 0.--15. 1. "TYPE,Type Field In PAUSE Frames" line.long 0x8 "OPD,Opcode/Pause Duration Register" hexmask.long.word 0x8 16.--31. 1. "OPCODE,Opcode Field In PAUSE Frames" newline hexmask.long.word 0x8 0.--15. 1. "PAUSE_DUR,Pause Duration" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xF0)++0x3 line.long 0x0 "TXIC[$1],Transmit Interrupt Coalescing Register" bitfld.long 0x0 31. "ICEN,Interrupt Coalescing Enable" "0: Disable Interrupt coalescing.,1: Enable Interrupt coalescing." newline bitfld.long 0x0 30. "ICCS,Interrupt Coalescing Timer Clock Source Select" "0: Use MII/GMII TX clocks.,1: Use ENET system clock." newline hexmask.long.byte 0x0 20.--27. 1. "ICFT,Interrupt coalescing frame count threshold" newline hexmask.long.word 0x0 0.--15. 1. "ICTT,Interrupt coalescing timer threshold" repeat.end repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x100)++0x3 line.long 0x0 "RXIC[$1],Receive Interrupt Coalescing Register" bitfld.long 0x0 31. "ICEN,Interrupt Coalescing Enable" "0: Disable Interrupt coalescing.,1: Enable Interrupt coalescing." newline bitfld.long 0x0 30. "ICCS,Interrupt Coalescing Timer Clock Source Select" "0: Use MII/GMII TX clocks.,1: Use ENET system clock." newline hexmask.long.byte 0x0 20.--27. 1. "ICFT,Interrupt coalescing frame count threshold" newline hexmask.long.word 0x0 0.--15. 1. "ICTT,Interrupt coalescing timer threshold" repeat.end group.long 0x118++0xF line.long 0x0 "IAUR,Descriptor Individual Upper Address Register" hexmask.long 0x0 0.--31. 1. "IADDR1,Contains the upper 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a unicast address" line.long 0x4 "IALR,Descriptor Individual Lower Address Register" hexmask.long 0x4 0.--31. 1. "IADDR2,Contains the lower 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a unicast address" line.long 0x8 "GAUR,Descriptor Group Upper Address Register" hexmask.long 0x8 0.--31. 1. "GADDR1,Contains the upper 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a multicast address" line.long 0xC "GALR,Descriptor Group Lower Address Register" hexmask.long 0xC 0.--31. 1. "GADDR2,Contains the lower 32 bits of the 64-bit hash table used in the address recognition process for receive frames with a multicast address" group.long 0x144++0x3 line.long 0x0 "TFWR,Transmit FIFO Watermark Register" bitfld.long 0x0 8. "STRFWD,Store And Forward Enable" "0: Reset. The transmission start threshold is..,1: Enabled." newline hexmask.long.byte 0x0 0.--5. 1. "TFWR,Transmit FIFO Write" group.long 0x160++0x17 line.long 0x0 "RDSR1,Receive Descriptor Ring 1 Start Register" hexmask.long 0x0 3.--31. 1. "R_DES_START,Pointer to the beginning of the receive buffer descriptor queue 1." line.long 0x4 "TDSR1,Transmit Buffer Descriptor Ring 1 Start Register" hexmask.long 0x4 3.--31. 1. "X_DES_START,Pointer to the beginning of transmit buffer descriptor queue 1." line.long 0x8 "MRBR1,Maximum Receive Buffer Size Register - Ring 1" hexmask.long.byte 0x8 4.--10. 1. "R_BUF_SIZE,Receive buffer size (in bytes)" line.long 0xC "RDSR2,Receive Descriptor Ring 2 Start Register" hexmask.long 0xC 3.--31. 1. "R_DES_START,Pointer to the beginning of receive buffer descriptor queue 2." line.long 0x10 "TDSR2,Transmit Buffer Descriptor Ring 2 Start Register" hexmask.long 0x10 3.--31. 1. "X_DES_START,Pointer to the beginning of transmit buffer descriptor queue 2." line.long 0x14 "MRBR2,Maximum Receive Buffer Size Register - Ring 2" hexmask.long.byte 0x14 4.--10. 1. "R_BUF_SIZE,Receive buffer size (in bytes)" group.long 0x180++0xB line.long 0x0 "RDSR,Receive Descriptor Ring 0 Start Register" hexmask.long 0x0 3.--31. 1. "R_DES_START,Pointer to the beginning of the receive buffer descriptor queue. 0" line.long 0x4 "TDSR,Transmit Buffer Descriptor Ring 0 Start Register" hexmask.long 0x4 3.--31. 1. "X_DES_START,Pointer to the beginning of the transmit buffer descriptor queue." line.long 0x8 "MRBR,Maximum Receive Buffer Size Register - Ring 0" hexmask.long.byte 0x8 4.--10. 1. "R_BUF_SIZE,Receive buffer size in bytes" group.long 0x190++0x23 line.long 0x0 "RSFL,Receive FIFO Section Full Threshold" hexmask.long.word 0x0 0.--9. 1. "RX_SECTION_FULL,Value Of Receive FIFO Section Full Threshold" line.long 0x4 "RSEM,Receive FIFO Section Empty Threshold" hexmask.long.byte 0x4 16.--20. 1. "STAT_SECTION_EMPTY,RX Status FIFO Section Empty Threshold" newline hexmask.long.word 0x4 0.--9. 1. "RX_SECTION_EMPTY,Value Of The Receive FIFO Section Empty Threshold" line.long 0x8 "RAEM,Receive FIFO Almost Empty Threshold" hexmask.long.word 0x8 0.--9. 1. "RX_ALMOST_EMPTY,Value Of The Receive FIFO Almost Empty Threshold" line.long 0xC "RAFL,Receive FIFO Almost Full Threshold" hexmask.long.word 0xC 0.--9. 1. "RX_ALMOST_FULL,Value Of The Receive FIFO Almost Full Threshold" line.long 0x10 "TSEM,Transmit FIFO Section Empty Threshold" hexmask.long.word 0x10 0.--9. 1. "TX_SECTION_EMPTY,Value Of The Transmit FIFO Section Empty Threshold" line.long 0x14 "TAEM,Transmit FIFO Almost Empty Threshold" hexmask.long.word 0x14 0.--9. 1. "TX_ALMOST_EMPTY,Value of Transmit FIFO Almost Empty Threshold" line.long 0x18 "TAFL,Transmit FIFO Almost Full Threshold" hexmask.long.word 0x18 0.--9. 1. "TX_ALMOST_FULL,Value Of The Transmit FIFO Almost Full Threshold" line.long 0x1C "TIPG,Transmit Inter-Packet Gap" hexmask.long.byte 0x1C 0.--4. 1. "IPG,Transmit Inter-Packet Gap" line.long 0x20 "FTRL,Frame Truncation Length" hexmask.long.word 0x20 0.--13. 1. "TRUNC_FL,Frame Truncation Length" group.long 0x1C0++0x7 line.long 0x0 "TACC,Transmit Accelerator Function Configuration" bitfld.long 0x0 4. "PROCHK,Enables insertion of protocol checksum." "0: Checksum not inserted.,1: If an IP frame with a known protocol is.." newline bitfld.long 0x0 3. "IPCHK,Enables insertion of IP header checksum." "0: Checksum is not inserted.,1: If an IP frame is transmitted the checksum is.." newline bitfld.long 0x0 0. "SHIFT16,TX FIFO Shift-16" "0: Disabled.,1: Indicates to the transmit data FIFO that the.." line.long 0x4 "RACC,Receive Accelerator Function Configuration" bitfld.long 0x4 7. "SHIFT16,RX FIFO Shift-16" "0: Disabled.,1: Instructs the MAC to write two additional bytes.." newline bitfld.long 0x4 6. "LINEDIS,Enable Discard Of Frames With MAC Layer Errors" "0: Frames with errors are not discarded.,1: Any frame received with a CRC length or PHY.." newline bitfld.long 0x4 2. "PRODIS,Enable Discard Of Frames With Wrong Protocol Checksum" "0: Frames with wrong checksum are not discarded.,1: If a TCP/IP UDP/IP or ICMP/IP frame is received.." newline bitfld.long 0x4 1. "IPDIS,Enable Discard Of Frames With Wrong IPv4 Header Checksum" "0: Frames with wrong IPv4 header checksum are not..,1: If an IPv4 frame is received with a mismatching.." newline bitfld.long 0x4 0. "PADREM,Enable Padding Removal For Short IP Frames" "0: Padding not removed.,1: Any bytes following the IP payload section of.." repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x1C8)++0x3 line.long 0x0 "RCMR$1,Receive Classification Match Register for Class n" bitfld.long 0x0 16. "MATCHEN,Match Enable" "0: Disabled (default): no compares will occur and..,1: The register contents are valid and a comparison.." newline bitfld.long 0x0 12.--14. "CMP3,Compare 3" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 8.--10. "CMP2,Compare 2" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 4.--6. "CMP1,Compare 1" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "CMP0,Compare 0" "0,1,2,3,4,5,6,7" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x1D8)++0x3 line.long 0x0 "DMACFG$1,DMA Class Based Configuration" bitfld.long 0x0 17. "CALC_NOIPG,Calculate no IPG" "0: The traffic shaper function should consider 12..,1: Addition of 12 bytes for the IPG should be.." newline bitfld.long 0x0 16. "DMA_CLASS_EN,DMA class enable" "0: The DMA controller's channel for the class is..,1: Enable the DMA controller to support the.." newline hexmask.long.word 0x0 0.--15. 1. "IDLE_SLOPE,Idle slope" repeat.end group.long 0x1E0++0x13 line.long 0x0 "RDAR1,Receive Descriptor Active Register - Ring 1" bitfld.long 0x0 24. "RDAR,Receive Descriptor Active" "0,1" line.long 0x4 "TDAR1,Transmit Descriptor Active Register - Ring 1" bitfld.long 0x4 24. "TDAR,Transmit Descriptor Active" "0,1" line.long 0x8 "RDAR2,Receive Descriptor Active Register - Ring 2" bitfld.long 0x8 24. "RDAR,Receive Descriptor Active" "0,1" line.long 0xC "TDAR2,Transmit Descriptor Active Register - Ring 2" bitfld.long 0xC 24. "TDAR,Transmit Descriptor Active" "0,1" line.long 0x10 "QOS,QOS Scheme" bitfld.long 0x10 5. "RX_FLUSH2,RX Flush Ring 2" "0: Disable,1: Enable" newline bitfld.long 0x10 4. "RX_FLUSH1,RX Flush Ring 1" "0: Disable,1: Enable" newline bitfld.long 0x10 3. "RX_FLUSH0,RX Flush Ring 0" "0: Disable,1: Enable" newline bitfld.long 0x10 0.--2. "TX_SCHEME,TX scheme configuration" "0: Credit-based scheme,1: Round-robin scheme,?,?,?,?,?,?" rgroup.long 0x204++0x73 line.long 0x0 "RMON_T_PACKETS,Tx Packet Count Statistic Register" hexmask.long.word 0x0 0.--15. 1. "TXPKTS,Packet count" line.long 0x4 "RMON_T_BC_PKT,Tx Broadcast Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "TXPKTS,Broadcast packets" line.long 0x8 "RMON_T_MC_PKT,Tx Multicast Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "TXPKTS,Multicast packets" line.long 0xC "RMON_T_CRC_ALIGN,Tx Packets with CRC/Align Error Statistic Register" hexmask.long.word 0xC 0.--15. 1. "TXPKTS,Packets with CRC/align error" line.long 0x10 "RMON_T_UNDERSIZE,Tx Packets Less Than Bytes and Good CRC Statistic Register" hexmask.long.word 0x10 0.--15. 1. "TXPKTS,Number of transmit packets less than 64 bytes with good CRC" line.long 0x14 "RMON_T_OVERSIZE,Tx Packets GT MAX_FL bytes and Good CRC Statistic Register" hexmask.long.word 0x14 0.--15. 1. "TXPKTS,Number of transmit packets greater than MAX_FL bytes with good CRC" line.long 0x18 "RMON_T_FRAG,Tx Packets Less Than 64 Bytes and Bad CRC Statistic Register" hexmask.long.word 0x18 0.--15. 1. "TXPKTS,Number of packets less than 64 bytes with bad CRC" line.long 0x1C "RMON_T_JAB,Tx Packets Greater Than MAX_FL bytes and Bad CRC Statistic Register" hexmask.long.word 0x1C 0.--15. 1. "TXPKTS,Number of transmit packets greater than MAX_FL bytes and bad CRC" line.long 0x20 "RMON_T_COL,Tx Collision Count Statistic Register" hexmask.long.word 0x20 0.--15. 1. "TXPKTS,Number of transmit collisions" line.long 0x24 "RMON_T_P64,Tx 64-Byte Packets Statistic Register" hexmask.long.word 0x24 0.--15. 1. "TXPKTS,Number of 64-byte transmit packets" line.long 0x28 "RMON_T_P65TO127,Tx 65- to 127-byte Packets Statistic Register" hexmask.long.word 0x28 0.--15. 1. "TXPKTS,Number of 65- to 127-byte transmit packets" line.long 0x2C "RMON_T_P128TO255,Tx 128- to 255-byte Packets Statistic Register" hexmask.long.word 0x2C 0.--15. 1. "TXPKTS,Number of 128- to 255-byte transmit packets" line.long 0x30 "RMON_T_P256TO511,Tx 256- to 511-byte Packets Statistic Register" hexmask.long.word 0x30 0.--15. 1. "TXPKTS,Number of 256- to 511-byte transmit packets" line.long 0x34 "RMON_T_P512TO1023,Tx 512- to 1023-byte Packets Statistic Register" hexmask.long.word 0x34 0.--15. 1. "TXPKTS,Number of 512- to 1023-byte transmit packets" line.long 0x38 "RMON_T_P1024TO2047,Tx 1024- to 2047-byte Packets Statistic Register" hexmask.long.word 0x38 0.--15. 1. "TXPKTS,Number of 1024- to 2047-byte transmit packets" line.long 0x3C "RMON_T_P_GTE2048,Tx Packets Greater Than 2048 Bytes Statistic Register" hexmask.long.word 0x3C 0.--15. 1. "TXPKTS,Number of transmit packets greater than 2048 bytes" line.long 0x40 "RMON_T_OCTETS,Tx Octets Statistic Register" hexmask.long 0x40 0.--31. 1. "TXOCTS,Number of transmit octets" line.long 0x44 "IEEE_T_DROP,Reserved Statistic Register" line.long 0x48 "IEEE_T_FRAME_OK,Frames Transmitted OK Statistic Register" hexmask.long.word 0x48 0.--15. 1. "COUNT,Number of frames transmitted OK" line.long 0x4C "IEEE_T_1COL,Frames Transmitted with Single Collision Statistic Register" hexmask.long.word 0x4C 0.--15. 1. "COUNT,Number of frames transmitted with one collision" line.long 0x50 "IEEE_T_MCOL,Frames Transmitted with Multiple Collisions Statistic Register" hexmask.long.word 0x50 0.--15. 1. "COUNT,Number of frames transmitted with multiple collisions" line.long 0x54 "IEEE_T_DEF,Frames Transmitted after Deferral Delay Statistic Register" hexmask.long.word 0x54 0.--15. 1. "COUNT,Number of frames transmitted with deferral delay" line.long 0x58 "IEEE_T_LCOL,Frames Transmitted with Late Collision Statistic Register" hexmask.long.word 0x58 0.--15. 1. "COUNT,Number of frames transmitted with late collision" line.long 0x5C "IEEE_T_EXCOL,Frames Transmitted with Excessive Collisions Statistic Register" hexmask.long.word 0x5C 0.--15. 1. "COUNT,Number of frames transmitted with excessive collisions" line.long 0x60 "IEEE_T_MACERR,Frames Transmitted with Tx FIFO Underrun Statistic Register" hexmask.long.word 0x60 0.--15. 1. "COUNT,Number of frames transmitted with transmit FIFO underrun" line.long 0x64 "IEEE_T_CSERR,Frames Transmitted with Carrier Sense Error Statistic Register" hexmask.long.word 0x64 0.--15. 1. "COUNT,Number of frames transmitted with carrier sense error" line.long 0x68 "IEEE_T_SQE,Reserved Statistic Register" hexmask.long.word 0x68 0.--15. 1. "COUNT,This read-only field is reserved and always has the value 0" line.long 0x6C "IEEE_T_FDXFC,Flow Control Pause Frames Transmitted Statistic Register" hexmask.long.word 0x6C 0.--15. 1. "COUNT,Number of flow-control pause frames transmitted" line.long 0x70 "IEEE_T_OCTETS_OK,Octet Count for Frames Transmitted w/o Error Statistic Register" hexmask.long 0x70 0.--31. 1. "COUNT,Octet count for frames transmitted without error Counts total octets (includes header and FCS fields)." rgroup.long 0x284++0x1F line.long 0x0 "RMON_R_PACKETS,Rx Packet Count Statistic Register" hexmask.long.word 0x0 0.--15. 1. "COUNT,Number of packets received" line.long 0x4 "RMON_R_BC_PKT,Rx Broadcast Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "COUNT,Number of receive broadcast packets" line.long 0x8 "RMON_R_MC_PKT,Rx Multicast Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "COUNT,Number of receive multicast packets" line.long 0xC "RMON_R_CRC_ALIGN,Rx Packets with CRC/Align Error Statistic Register" hexmask.long.word 0xC 0.--15. 1. "COUNT,Number of receive packets with CRC or align error" line.long 0x10 "RMON_R_UNDERSIZE,Rx Packets with Less Than 64 Bytes and Good CRC Statistic Register" hexmask.long.word 0x10 0.--15. 1. "COUNT,Number of receive packets with less than 64 bytes and good CRC" line.long 0x14 "RMON_R_OVERSIZE,Rx Packets Greater Than MAX_FL and Good CRC Statistic Register" hexmask.long.word 0x14 0.--15. 1. "COUNT,Number of receive packets greater than MAX_FL and good CRC" line.long 0x18 "RMON_R_FRAG,Rx Packets Less Than 64 Bytes and Bad CRC Statistic Register" hexmask.long.word 0x18 0.--15. 1. "COUNT,Number of receive packets with less than 64 bytes and bad CRC" line.long 0x1C "RMON_R_JAB,Rx Packets Greater Than MAX_FL Bytes and Bad CRC Statistic Register" hexmask.long.word 0x1C 0.--15. 1. "COUNT,Number of receive packets greater than MAX_FL and bad CRC" rgroup.long 0x2A8++0x3B line.long 0x0 "RMON_R_P64,Rx 64-Byte Packets Statistic Register" hexmask.long.word 0x0 0.--15. 1. "COUNT,Number of 64-byte receive packets" line.long 0x4 "RMON_R_P65TO127,Rx 65- to 127-Byte Packets Statistic Register" hexmask.long.word 0x4 0.--15. 1. "COUNT,Number of 65- to 127-byte recieve packets" line.long 0x8 "RMON_R_P128TO255,Rx 128- to 255-Byte Packets Statistic Register" hexmask.long.word 0x8 0.--15. 1. "COUNT,Number of 128- to 255-byte recieve packets" line.long 0xC "RMON_R_P256TO511,Rx 256- to 511-Byte Packets Statistic Register" hexmask.long.word 0xC 0.--15. 1. "COUNT,Number of 256- to 511-byte recieve packets" line.long 0x10 "RMON_R_P512TO1023,Rx 512- to 1023-Byte Packets Statistic Register" hexmask.long.word 0x10 0.--15. 1. "COUNT,Number of 512- to 1023-byte recieve packets" line.long 0x14 "RMON_R_P1024TO2047,Rx 1024- to 2047-Byte Packets Statistic Register" hexmask.long.word 0x14 0.--15. 1. "COUNT,Number of 1024- to 2047-byte recieve packets" line.long 0x18 "RMON_R_P_GTE2048,Rx Packets Greater than 2048 Bytes Statistic Register" hexmask.long.word 0x18 0.--15. 1. "COUNT,Number of greater-than-2048-byte recieve packets" line.long 0x1C "RMON_R_OCTETS,Rx Octets Statistic Register" hexmask.long 0x1C 0.--31. 1. "COUNT,Number of receive octets" line.long 0x20 "IEEE_R_DROP,Frames not Counted Correctly Statistic Register" hexmask.long.word 0x20 0.--15. 1. "COUNT,Frame count" line.long 0x24 "IEEE_R_FRAME_OK,Frames Received OK Statistic Register" hexmask.long.word 0x24 0.--15. 1. "COUNT,Number of frames received OK" line.long 0x28 "IEEE_R_CRC,Frames Received with CRC Error Statistic Register" hexmask.long.word 0x28 0.--15. 1. "COUNT,Number of frames received with CRC error" line.long 0x2C "IEEE_R_ALIGN,Frames Received with Alignment Error Statistic Register" hexmask.long.word 0x2C 0.--15. 1. "COUNT,Number of frames received with alignment error" line.long 0x30 "IEEE_R_MACERR,Receive FIFO Overflow Count Statistic Register" hexmask.long.word 0x30 0.--15. 1. "COUNT,Receive FIFO overflow count" line.long 0x34 "IEEE_R_FDXFC,Flow Control Pause Frames Received Statistic Register" hexmask.long.word 0x34 0.--15. 1. "COUNT,Number of flow-control pause frames received" line.long 0x38 "IEEE_R_OCTETS_OK,Octet Count for Frames Received without Error Statistic Register" hexmask.long 0x38 0.--31. 1. "COUNT,Number of octets for frames received without error" group.long 0x400++0x17 line.long 0x0 "ATCR,Adjustable Timer Control Register" bitfld.long 0x0 13. "SLAVE,Enable Timer Slave Mode" "0: The timer is active and all configuration fields..,1: The internal timer is disabled and the.." newline bitfld.long 0x0 11. "CAPTURE,Capture Timer Value" "0: No effect.,1: The current time is captured and can be read.." newline bitfld.long 0x0 9. "RESTART,Reset Timer" "0,1" newline bitfld.long 0x0 7. "PINPER,Enables event signal output external pin frc_evt_period assertion on period event" "0: Disable.,1: Enable." newline bitfld.long 0x0 4. "PEREN,Enable Periodical Event" "0: Disable.,1: A period event interrupt can be generated.." newline bitfld.long 0x0 3. "OFFRST,Reset Timer On Offset Event" "0: The timer is not affected and no action occurs..,1: If OFFEN is set the timer resets to zero when.." newline bitfld.long 0x0 2. "OFFEN,Enable One-Shot Offset Event" "0: Disable.,1: The timer can be reset to zero when the given.." newline bitfld.long 0x0 0. "EN,Enable Timer" "0: The timer stops at the current value.,1: The timer starts incrementing." line.long 0x4 "ATVR,Timer Value Register" hexmask.long 0x4 0.--31. 1. "ATIME,A write sets the timer" line.long 0x8 "ATOFF,Timer Offset Register" hexmask.long 0x8 0.--31. 1. "OFFSET,Offset value for one-shot event generation" line.long 0xC "ATPER,Timer Period Register" hexmask.long 0xC 0.--31. 1. "PERIOD,Value for generating periodic events" line.long 0x10 "ATCOR,Timer Correction Register" hexmask.long 0x10 0.--30. 1. "COR,Correction Counter Wrap-Around Value" line.long 0x14 "ATINC,Time-Stamping Clock Period Register" hexmask.long.byte 0x14 8.--14. 1. "INC_CORR,Correction Increment Value" newline hexmask.long.byte 0x14 0.--6. 1. "INC,Clock Period Of The Timestamping Clock (ts_clk) In Nanoseconds" rgroup.long 0x418++0x3 line.long 0x0 "ATSTMP,Timestamp of Last Transmitted Frame" hexmask.long 0x0 0.--31. 1. "TIMESTAMP,Timestamp of the last frame transmitted by the core that had TxBD[TS] set the ff_tx_ts_frm signal asserted from the user application" group.long 0x604++0x23 line.long 0x0 "TGSR,Timer Global Status Register" eventfld.long 0x0 3. "TF3,Copy Of Timer Flag For Channel 3" "0: Timer Flag for Channel 3 is clear,1: Timer Flag for Channel 3 is set" newline eventfld.long 0x0 2. "TF2,Copy Of Timer Flag For Channel 2" "0: Timer Flag for Channel 2 is clear,1: Timer Flag for Channel 2 is set" newline eventfld.long 0x0 1. "TF1,Copy Of Timer Flag For Channel 1" "0: Timer Flag for Channel 1 is clear,1: Timer Flag for Channel 1 is set" newline eventfld.long 0x0 0. "TF0,Copy Of Timer Flag For Channel 0" "0: Timer Flag for Channel 0 is clear,1: Timer Flag for Channel 0 is set" line.long 0x4 "TCSR0,Timer Control Status Register" eventfld.long 0x4 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x4 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x4 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x4 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x8 "TCCR0,Timer Compare Capture Register" hexmask.long 0x8 0.--31. 1. "TCC,Timer Capture Compare" line.long 0xC "TCSR1,Timer Control Status Register" eventfld.long 0xC 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0xC 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0xC 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0xC 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "TCCR1,Timer Compare Capture Register" hexmask.long 0x10 0.--31. 1. "TCC,Timer Capture Compare" line.long 0x14 "TCSR2,Timer Control Status Register" eventfld.long 0x14 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x14 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x14 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x14 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x18 "TCCR2,Timer Compare Capture Register" hexmask.long 0x18 0.--31. 1. "TCC,Timer Capture Compare" line.long 0x1C "TCSR3,Timer Control Status Register" eventfld.long 0x1C 7. "TF,Timer Flag" "0: Input Capture or Output Compare has not occurred.,1: Input Capture or Output Compare has occurred." newline bitfld.long 0x1C 6. "TIE,Timer Interrupt Enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.byte 0x1C 2.--5. 1. "TMODE,Timer Mode" newline bitfld.long 0x1C 0. "TDRE,Timer DMA Request Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x20 "TCCR3,Timer Compare Capture Register" hexmask.long 0x20 0.--31. 1. "TCC,Timer Capture Compare" tree.end tree.end tree "ETHERNET_PLL" base ad:0x0 group.long 0x0++0x3F line.long 0x0 "CTRL0,Fractional PLL Control Register" bitfld.long 0x0 29. "BIAS_SELECT,BIAS_SELECT" "0: Used in SoCs with a bias current of 10uA,1: Used in SoCs with a bias current of 2uA" bitfld.long 0x0 25.--27. "POST_DIV_SEL,Post Divide Select" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,?,?" newline bitfld.long 0x0 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x0 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 17. "DITHER_EN,DITHER_EN" "0: Disable Dither,1: Enable Dither" bitfld.long 0x0 16. "BYPASS,BYPASS" "0: No Bypass,1: Bypass the PLL" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable the clock output,1: Enable the clock output" bitfld.long 0x0 14. "POWERUP,POWERUP" "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 13. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" bitfld.long 0x0 8. "ENABLE_ALT,ENABLE_ALT" "0: Disable the alternate clock output,1: Enable the alternate clock output which is the.." newline hexmask.long.byte 0x0 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x4 "CTRL0_SET,Fractional PLL Control Register" bitfld.long 0x4 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0x4 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x4 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0x4 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0x4 15. "ENABLE,ENABLE" "0,1" bitfld.long 0x4 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0x4 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0x4 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x4 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x8 "CTRL0_CLR,Fractional PLL Control Register" eventfld.long 0x8 29. "BIAS_SELECT,BIAS_SELECT" "0,1" eventfld.long 0x8 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 22. "PLL_REG_EN,PLL_REG_EN" "0,1" eventfld.long 0x8 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 17. "DITHER_EN,DITHER_EN" "0,1" eventfld.long 0x8 16. "BYPASS,BYPASS" "0,1" newline eventfld.long 0x8 15. "ENABLE,ENABLE" "0,1" eventfld.long 0x8 14. "POWERUP,POWERUP" "0,1" newline eventfld.long 0x8 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" eventfld.long 0x8 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x8 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0xC "CTRL0_TOG,Fractional PLL Control Register" bitfld.long 0xC 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0xC 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0xC 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0xC 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0xC 15. "ENABLE,ENABLE" "0,1" bitfld.long 0xC 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0xC 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0xC 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0xC 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x10 "SPREAD_SPECTRUM,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x10 16.--31. 1. "STOP,Stop" bitfld.long 0x10 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x10 0.--14. 1. "STEP,Step" line.long 0x14 "SPREAD_SPECTRUM_SET,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x14 16.--31. 1. "STOP,Stop" bitfld.long 0x14 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x14 0.--14. 1. "STEP,Step" line.long 0x18 "SPREAD_SPECTRUM_CLR,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x18 16.--31. 1. "STOP,Stop" eventfld.long 0x18 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x18 0.--14. 1. "STEP,Step" line.long 0x1C "SPREAD_SPECTRUM_TOG,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x1C 16.--31. 1. "STOP,Stop" bitfld.long 0x1C 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x1C 0.--14. 1. "STEP,Step" line.long 0x20 "NUMERATOR,Fractional PLL Numerator Control Register" hexmask.long 0x20 0.--29. 1. "NUM,Numerator" line.long 0x24 "NUMERATOR_SET,Fractional PLL Numerator Control Register" hexmask.long 0x24 0.--29. 1. "NUM,Numerator" line.long 0x28 "NUMERATOR_CLR,Fractional PLL Numerator Control Register" hexmask.long 0x28 0.--29. 1. "NUM,Numerator" line.long 0x2C "NUMERATOR_TOG,Fractional PLL Numerator Control Register" hexmask.long 0x2C 0.--29. 1. "NUM,Numerator" line.long 0x30 "DENOMINATOR,Fractional PLL Denominator Control Register" hexmask.long 0x30 0.--29. 1. "DENOM,Denominator" line.long 0x34 "DENOMINATOR_SET,Fractional PLL Denominator Control Register" hexmask.long 0x34 0.--29. 1. "DENOM,Denominator" line.long 0x38 "DENOMINATOR_CLR,Fractional PLL Denominator Control Register" hexmask.long 0x38 0.--29. 1. "DENOM,Denominator" line.long 0x3C "DENOMINATOR_TOG,Fractional PLL Denominator Control Register" hexmask.long 0x3C 0.--29. 1. "DENOM,Denominator" tree.end tree "EWM" base ad:0x4002C000 group.byte 0x0++0x5 line.byte 0x0 "CTRL,Control Register" bitfld.byte 0x0 3. "INTEN,Interrupt Enable." "0: Deasserts the interrupt request.,1: Generates an interrupt request when EWM_OUT_b is.." bitfld.byte 0x0 2. "INEN,Input Enable." "0: EWM_in port is disabled.,1: EWM_in port is enabled." newline bitfld.byte 0x0 1. "ASSIN,EWM_in's Assertion State Select." "0: Default assert state of the EWM_in signal.,1: Inverts the assert state of EWM_in signal." bitfld.byte 0x0 0. "EWMEN,EWM enable." "0: EWM module is disabled.,1: EWM module is enabled." line.byte 0x1 "SERV,Service Register" hexmask.byte 0x1 0.--7. 1. "SERVICE,SERVICE" line.byte 0x2 "CMPL,Compare Low Register" hexmask.byte 0x2 0.--7. 1. "COMPAREL,COMPAREL" line.byte 0x3 "CMPH,Compare High Register" hexmask.byte 0x3 0.--7. 1. "COMPAREH,COMPAREH" line.byte 0x4 "CLKCTRL,Clock Control Register" bitfld.byte 0x4 0.--1. "CLKSEL,CLKSEL" "0,1,2,3" line.byte 0x5 "CLKPRESCALER,Clock Prescaler Register" hexmask.byte 0x5 0.--7. 1. "CLK_DIV,CLK_DIV" tree.end tree "FLEXIO" base ad:0x0 tree "FLEXIO1" base ad:0x400AC000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 24.--31. 1. "TRIGGER,Trigger Number" hexmask.long.byte 0x4 16.--23. 1. "PIN,Pin Number" newline hexmask.long.byte 0x4 8.--15. 1. "TIMER,Timer Number" hexmask.long.byte 0x4 0.--7. 1. "SHIFTER,Shifter Number" group.long 0x8++0x3 line.long 0x0 "CTRL,FlexIO Control Register" bitfld.long 0x0 31. "DOZEN,Doze Enable" "0: FlexIO enabled in Doze modes.,1: FlexIO disabled in Doze modes." bitfld.long 0x0 30. "DBGE,Debug Enable" "0: FlexIO is disabled in debug modes.,1: FlexIO is enabled in debug modes" newline bitfld.long 0x0 2. "FASTACC,Fast Access" "0: Configures for normal register accesses to FlexIO,1: Configures for fast register accesses to FlexIO" bitfld.long 0x0 1. "SWRST,Software Reset" "0: Software reset is disabled,1: Software reset is enabled all FlexIO registers.." newline bitfld.long 0x0 0. "FLEXEN,FlexIO Enable" "0: FlexIO module is disabled.,1: FlexIO module is enabled." rgroup.long 0xC++0x3 line.long 0x0 "PIN,Pin State Register" hexmask.long 0x0 0.--31. 1. "PDI,Pin Data Input" group.long 0x10++0xB line.long 0x0 "SHIFTSTAT,Shifter Status Register" hexmask.long.byte 0x0 0.--7. 1. "SSF,Shifter Status Flag" line.long 0x4 "SHIFTERR,Shifter Error Register" hexmask.long.byte 0x4 0.--7. 1. "SEF,Shifter Error Flags" line.long 0x8 "TIMSTAT,Timer Status Register" hexmask.long.byte 0x8 0.--7. 1. "TSF,Timer Status Flags" group.long 0x20++0xB line.long 0x0 "SHIFTSIEN,Shifter Status Interrupt Enable" hexmask.long.byte 0x0 0.--7. 1. "SSIE,Shifter Status Interrupt Enable" line.long 0x4 "SHIFTEIEN,Shifter Error Interrupt Enable" hexmask.long.byte 0x4 0.--7. 1. "SEIE,Shifter Error Interrupt Enable" line.long 0x8 "TIMIEN,Timer Interrupt Enable Register" hexmask.long.byte 0x8 0.--7. 1. "TEIE,Timer Status Interrupt Enable" group.long 0x30++0x3 line.long 0x0 "SHIFTSDEN,Shifter Status DMA Enable" hexmask.long.byte 0x0 0.--7. 1. "SSDE,Shifter Status DMA Enable" group.long 0x38++0x3 line.long 0x0 "TIMERSDEN,Timer Status DMA Enable" hexmask.long.byte 0x0 0.--7. 1. "TSDE,Timer Status DMA Enable" group.long 0x40++0x3 line.long 0x0 "SHIFTSTATE,Shifter State Register" bitfld.long 0x0 0.--2. "STATE,Current State Pointer" "0,1,2,3,4,5,6,7" repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x80)++0x3 line.long 0x0 "SHIFTCTL[$1],Shifter Control N Register" bitfld.long 0x0 24.--26. "TIMSEL,Timer Select" "0,1,2,3,4,5,6,7" bitfld.long 0x0 23. "TIMPOL,Timer Polarity" "0: Shift on posedge of Shift clock,1: Shift on negedge of Shift clock" newline bitfld.long 0x0 16.--17. "PINCFG,Shifter Pin Configuration" "0: Shifter pin output disabled,1: Shifter pin open drain or bidirectional output..,2: Shifter pin bidirectional output data,3: Shifter pin output" hexmask.long.byte 0x0 8.--12. 1. "PINSEL,Shifter Pin Select" newline bitfld.long 0x0 7. "PINPOL,Shifter Pin Polarity" "0: Pin is active high,1: Pin is active low" bitfld.long 0x0 0.--2. "SMOD,Shifter Mode" "0: Disabled.,1: Receive mode. Captures the current Shifter..,2: Transmit mode. Load SHIFTBUF contents into the..,?,4: Match Store mode. Shifter data is compared to..,5: Match Continuous mode. Shifter data is..,6: State mode. SHIFTBUF contents are used for..,7: Logic mode. SHIFTBUF contents are used for.." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x100)++0x3 line.long 0x0 "SHIFTCFG[$1],Shifter Configuration N Register" hexmask.long.byte 0x0 16.--20. 1. "PWIDTH,Parallel Width" bitfld.long 0x0 9. "LATST,Late Store" "0: Shift register stores the pre-shift register..,1: Shift register stores the post-shift register.." newline bitfld.long 0x0 8. "INSRC,Input Source" "0: Pin,1: Shifter N+1 Output" bitfld.long 0x0 4.--5. "SSTOP,Shifter Stop bit" "0: Stop bit disabled for transmitter/receiver/match..,?,2: Transmitter outputs stop bit value 0 on store..,3: Transmitter outputs stop bit value 1 on store.." newline bitfld.long 0x0 0.--1. "SSTART,Shifter Start bit" "0: Start bit disabled for..,1: Start bit disabled for..,2: Transmitter outputs start bit value 0 before..,3: Transmitter outputs start bit value 1 before.." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "SHIFTBUF[$1],Shifter Buffer N Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUF,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x280)++0x3 line.long 0x0 "SHIFTBUFBIS[$1],Shifter Buffer N Bit Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBIS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x300)++0x3 line.long 0x0 "SHIFTBUFBYS[$1],Shifter Buffer N Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBYS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x380)++0x3 line.long 0x0 "SHIFTBUFBBS[$1],Shifter Buffer N Bit Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBBS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x400)++0x3 line.long 0x0 "TIMCTL[$1],Timer Control N Register" hexmask.long.byte 0x0 24.--29. 1. "TRGSEL,Trigger Select" bitfld.long 0x0 23. "TRGPOL,Trigger Polarity" "0: Trigger active high,1: Trigger active low" newline bitfld.long 0x0 22. "TRGSRC,Trigger Source" "0: External trigger selected,1: Internal trigger selected" bitfld.long 0x0 16.--17. "PINCFG,Timer Pin Configuration" "0: Timer pin output disabled,1: Timer pin open drain or bidirectional output..,2: Timer pin bidirectional output data,3: Timer pin output" newline hexmask.long.byte 0x0 8.--12. 1. "PINSEL,Timer Pin Select" bitfld.long 0x0 7. "PINPOL,Timer Pin Polarity" "0: Pin is active high,1: Pin is active low" newline bitfld.long 0x0 6. "PININS,Timer Pin Input Select" "0: Timer pin input and output are selected by PINSEL.,1: Timer pin input is selected by PINSEL+1 timer.." bitfld.long 0x0 5. "ONETIM,Timer One Time Operation" "0: The timer enable event is generated as normal.,1: The timer enable event is blocked unless timer.." newline bitfld.long 0x0 0.--2. "TIMOD,Timer Mode" "0: Timer Disabled.,1: Dual 8-bit counters baud mode.,2: Dual 8-bit counters PWM high mode.,3: Single 16-bit counter mode.,4: Single 16-bit counter disable mode.,5: Dual 8-bit counters word mode.,6: Dual 8-bit counters PWM low mode.,7: Single 16-bit input capture mode." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x480)++0x3 line.long 0x0 "TIMCFG[$1],Timer Configuration N Register" bitfld.long 0x0 24.--25. "TIMOUT,Timer Output" "0: Timer output is logic one when enabled and is..,1: Timer output is logic zero when enabled and is..,2: Timer output is logic one when enabled and on..,3: Timer output is logic zero when enabled and on.." bitfld.long 0x0 20.--22. "TIMDEC,Timer Decrement" "0: Decrement counter on FlexIO clock Shift clock..,1: Decrement counter on Trigger input (both edges)..,2: Decrement counter on Pin input (both edges)..,3: Decrement counter on Trigger input (both edges)..,4: Decrement counter on FlexIO clock divided by 16..,5: Decrement counter on FlexIO clock divided by 256..,6: Decrement counter on Pin input (rising edge)..,7: Decrement counter on Trigger input (rising edge).." newline bitfld.long 0x0 16.--18. "TIMRST,Timer Reset" "0: Timer never reset,1: Timer reset on Timer Output high.,2: Timer reset on Timer Pin equal to Timer Output,3: Timer reset on Timer Trigger equal to Timer Output,4: Timer reset on Timer Pin rising edge,?,6: Timer reset on Trigger rising edge,7: Timer reset on Trigger rising or falling edge" bitfld.long 0x0 12.--14. "TIMDIS,Timer Disable" "0: Timer never disabled,1: Timer disabled on Timer N-1 disable,2: Timer disabled on Timer compare (upper 8-bits..,3: Timer disabled on Timer compare (upper 8-bits..,4: Timer disabled on Pin rising or falling edge,5: Timer disabled on Pin rising or falling edge..,6: Timer disabled on Trigger falling edge,?" newline bitfld.long 0x0 8.--10. "TIMENA,Timer Enable" "0: Timer always enabled,1: Timer enabled on Timer N-1 enable,2: Timer enabled on Trigger high,3: Timer enabled on Trigger high and Pin high,4: Timer enabled on Pin rising edge,5: Timer enabled on Pin rising edge and Trigger high,6: Timer enabled on Trigger rising edge,7: Timer enabled on Trigger rising or falling edge" bitfld.long 0x0 4.--5. "TSTOP,Timer Stop Bit" "0: Stop bit disabled,1: Stop bit is enabled on timer compare,2: Stop bit is enabled on timer disable,3: Stop bit is enabled on timer compare and timer.." newline bitfld.long 0x0 1. "TSTART,Timer Start Bit" "0: Start bit disabled,1: Start bit enabled" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x500)++0x3 line.long 0x0 "TIMCMP[$1],Timer Compare N Register" hexmask.long.word 0x0 0.--15. 1. "CMP,Timer Compare Value" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x680)++0x3 line.long 0x0 "SHIFTBUFNBS[$1],Shifter Buffer N Nibble Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFNBS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x700)++0x3 line.long 0x0 "SHIFTBUFHWS[$1],Shifter Buffer N Half Word Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFHWS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x780)++0x3 line.long 0x0 "SHIFTBUFNIS[$1],Shifter Buffer N Nibble Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFNIS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x800)++0x3 line.long 0x0 "SHIFTBUFOES[$1],Shifter Buffer N Odd Even Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFOES,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x880)++0x3 line.long 0x0 "SHIFTBUFEOS[$1],Shifter Buffer N Even Odd Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFEOS,Shift Buffer" repeat.end tree.end tree "FLEXIO2" base ad:0x400B0000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 24.--31. 1. "TRIGGER,Trigger Number" hexmask.long.byte 0x4 16.--23. 1. "PIN,Pin Number" newline hexmask.long.byte 0x4 8.--15. 1. "TIMER,Timer Number" hexmask.long.byte 0x4 0.--7. 1. "SHIFTER,Shifter Number" group.long 0x8++0x3 line.long 0x0 "CTRL,FlexIO Control Register" bitfld.long 0x0 31. "DOZEN,Doze Enable" "0: FlexIO enabled in Doze modes.,1: FlexIO disabled in Doze modes." bitfld.long 0x0 30. "DBGE,Debug Enable" "0: FlexIO is disabled in debug modes.,1: FlexIO is enabled in debug modes" newline bitfld.long 0x0 2. "FASTACC,Fast Access" "0: Configures for normal register accesses to FlexIO,1: Configures for fast register accesses to FlexIO" bitfld.long 0x0 1. "SWRST,Software Reset" "0: Software reset is disabled,1: Software reset is enabled all FlexIO registers.." newline bitfld.long 0x0 0. "FLEXEN,FlexIO Enable" "0: FlexIO module is disabled.,1: FlexIO module is enabled." rgroup.long 0xC++0x3 line.long 0x0 "PIN,Pin State Register" hexmask.long 0x0 0.--31. 1. "PDI,Pin Data Input" group.long 0x10++0xB line.long 0x0 "SHIFTSTAT,Shifter Status Register" hexmask.long.byte 0x0 0.--7. 1. "SSF,Shifter Status Flag" line.long 0x4 "SHIFTERR,Shifter Error Register" hexmask.long.byte 0x4 0.--7. 1. "SEF,Shifter Error Flags" line.long 0x8 "TIMSTAT,Timer Status Register" hexmask.long.byte 0x8 0.--7. 1. "TSF,Timer Status Flags" group.long 0x20++0xB line.long 0x0 "SHIFTSIEN,Shifter Status Interrupt Enable" hexmask.long.byte 0x0 0.--7. 1. "SSIE,Shifter Status Interrupt Enable" line.long 0x4 "SHIFTEIEN,Shifter Error Interrupt Enable" hexmask.long.byte 0x4 0.--7. 1. "SEIE,Shifter Error Interrupt Enable" line.long 0x8 "TIMIEN,Timer Interrupt Enable Register" hexmask.long.byte 0x8 0.--7. 1. "TEIE,Timer Status Interrupt Enable" group.long 0x30++0x3 line.long 0x0 "SHIFTSDEN,Shifter Status DMA Enable" hexmask.long.byte 0x0 0.--7. 1. "SSDE,Shifter Status DMA Enable" group.long 0x38++0x3 line.long 0x0 "TIMERSDEN,Timer Status DMA Enable" hexmask.long.byte 0x0 0.--7. 1. "TSDE,Timer Status DMA Enable" group.long 0x40++0x3 line.long 0x0 "SHIFTSTATE,Shifter State Register" bitfld.long 0x0 0.--2. "STATE,Current State Pointer" "0,1,2,3,4,5,6,7" repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x80)++0x3 line.long 0x0 "SHIFTCTL[$1],Shifter Control N Register" bitfld.long 0x0 24.--26. "TIMSEL,Timer Select" "0,1,2,3,4,5,6,7" bitfld.long 0x0 23. "TIMPOL,Timer Polarity" "0: Shift on posedge of Shift clock,1: Shift on negedge of Shift clock" newline bitfld.long 0x0 16.--17. "PINCFG,Shifter Pin Configuration" "0: Shifter pin output disabled,1: Shifter pin open drain or bidirectional output..,2: Shifter pin bidirectional output data,3: Shifter pin output" hexmask.long.byte 0x0 8.--12. 1. "PINSEL,Shifter Pin Select" newline bitfld.long 0x0 7. "PINPOL,Shifter Pin Polarity" "0: Pin is active high,1: Pin is active low" bitfld.long 0x0 0.--2. "SMOD,Shifter Mode" "0: Disabled.,1: Receive mode. Captures the current Shifter..,2: Transmit mode. Load SHIFTBUF contents into the..,?,4: Match Store mode. Shifter data is compared to..,5: Match Continuous mode. Shifter data is..,6: State mode. SHIFTBUF contents are used for..,7: Logic mode. SHIFTBUF contents are used for.." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x100)++0x3 line.long 0x0 "SHIFTCFG[$1],Shifter Configuration N Register" hexmask.long.byte 0x0 16.--20. 1. "PWIDTH,Parallel Width" bitfld.long 0x0 9. "LATST,Late Store" "0: Shift register stores the pre-shift register..,1: Shift register stores the post-shift register.." newline bitfld.long 0x0 8. "INSRC,Input Source" "0: Pin,1: Shifter N+1 Output" bitfld.long 0x0 4.--5. "SSTOP,Shifter Stop bit" "0: Stop bit disabled for transmitter/receiver/match..,?,2: Transmitter outputs stop bit value 0 on store..,3: Transmitter outputs stop bit value 1 on store.." newline bitfld.long 0x0 0.--1. "SSTART,Shifter Start bit" "0: Start bit disabled for..,1: Start bit disabled for..,2: Transmitter outputs start bit value 0 before..,3: Transmitter outputs start bit value 1 before.." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "SHIFTBUF[$1],Shifter Buffer N Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUF,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x280)++0x3 line.long 0x0 "SHIFTBUFBIS[$1],Shifter Buffer N Bit Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBIS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x300)++0x3 line.long 0x0 "SHIFTBUFBYS[$1],Shifter Buffer N Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBYS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x380)++0x3 line.long 0x0 "SHIFTBUFBBS[$1],Shifter Buffer N Bit Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFBBS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x400)++0x3 line.long 0x0 "TIMCTL[$1],Timer Control N Register" hexmask.long.byte 0x0 24.--29. 1. "TRGSEL,Trigger Select" bitfld.long 0x0 23. "TRGPOL,Trigger Polarity" "0: Trigger active high,1: Trigger active low" newline bitfld.long 0x0 22. "TRGSRC,Trigger Source" "0: External trigger selected,1: Internal trigger selected" bitfld.long 0x0 16.--17. "PINCFG,Timer Pin Configuration" "0: Timer pin output disabled,1: Timer pin open drain or bidirectional output..,2: Timer pin bidirectional output data,3: Timer pin output" newline hexmask.long.byte 0x0 8.--12. 1. "PINSEL,Timer Pin Select" bitfld.long 0x0 7. "PINPOL,Timer Pin Polarity" "0: Pin is active high,1: Pin is active low" newline bitfld.long 0x0 6. "PININS,Timer Pin Input Select" "0: Timer pin input and output are selected by PINSEL.,1: Timer pin input is selected by PINSEL+1 timer.." bitfld.long 0x0 5. "ONETIM,Timer One Time Operation" "0: The timer enable event is generated as normal.,1: The timer enable event is blocked unless timer.." newline bitfld.long 0x0 0.--2. "TIMOD,Timer Mode" "0: Timer Disabled.,1: Dual 8-bit counters baud mode.,2: Dual 8-bit counters PWM high mode.,3: Single 16-bit counter mode.,4: Single 16-bit counter disable mode.,5: Dual 8-bit counters word mode.,6: Dual 8-bit counters PWM low mode.,7: Single 16-bit input capture mode." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x480)++0x3 line.long 0x0 "TIMCFG[$1],Timer Configuration N Register" bitfld.long 0x0 24.--25. "TIMOUT,Timer Output" "0: Timer output is logic one when enabled and is..,1: Timer output is logic zero when enabled and is..,2: Timer output is logic one when enabled and on..,3: Timer output is logic zero when enabled and on.." bitfld.long 0x0 20.--22. "TIMDEC,Timer Decrement" "0: Decrement counter on FlexIO clock Shift clock..,1: Decrement counter on Trigger input (both edges)..,2: Decrement counter on Pin input (both edges)..,3: Decrement counter on Trigger input (both edges)..,4: Decrement counter on FlexIO clock divided by 16..,5: Decrement counter on FlexIO clock divided by 256..,6: Decrement counter on Pin input (rising edge)..,7: Decrement counter on Trigger input (rising edge).." newline bitfld.long 0x0 16.--18. "TIMRST,Timer Reset" "0: Timer never reset,1: Timer reset on Timer Output high.,2: Timer reset on Timer Pin equal to Timer Output,3: Timer reset on Timer Trigger equal to Timer Output,4: Timer reset on Timer Pin rising edge,?,6: Timer reset on Trigger rising edge,7: Timer reset on Trigger rising or falling edge" bitfld.long 0x0 12.--14. "TIMDIS,Timer Disable" "0: Timer never disabled,1: Timer disabled on Timer N-1 disable,2: Timer disabled on Timer compare (upper 8-bits..,3: Timer disabled on Timer compare (upper 8-bits..,4: Timer disabled on Pin rising or falling edge,5: Timer disabled on Pin rising or falling edge..,6: Timer disabled on Trigger falling edge,?" newline bitfld.long 0x0 8.--10. "TIMENA,Timer Enable" "0: Timer always enabled,1: Timer enabled on Timer N-1 enable,2: Timer enabled on Trigger high,3: Timer enabled on Trigger high and Pin high,4: Timer enabled on Pin rising edge,5: Timer enabled on Pin rising edge and Trigger high,6: Timer enabled on Trigger rising edge,7: Timer enabled on Trigger rising or falling edge" bitfld.long 0x0 4.--5. "TSTOP,Timer Stop Bit" "0: Stop bit disabled,1: Stop bit is enabled on timer compare,2: Stop bit is enabled on timer disable,3: Stop bit is enabled on timer compare and timer.." newline bitfld.long 0x0 1. "TSTART,Timer Start Bit" "0: Start bit disabled,1: Start bit enabled" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x500)++0x3 line.long 0x0 "TIMCMP[$1],Timer Compare N Register" hexmask.long.word 0x0 0.--15. 1. "CMP,Timer Compare Value" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x680)++0x3 line.long 0x0 "SHIFTBUFNBS[$1],Shifter Buffer N Nibble Byte Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFNBS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x700)++0x3 line.long 0x0 "SHIFTBUFHWS[$1],Shifter Buffer N Half Word Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFHWS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x780)++0x3 line.long 0x0 "SHIFTBUFNIS[$1],Shifter Buffer N Nibble Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFNIS,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x800)++0x3 line.long 0x0 "SHIFTBUFOES[$1],Shifter Buffer N Odd Even Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFOES,Shift Buffer" repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x880)++0x3 line.long 0x0 "SHIFTBUFEOS[$1],Shifter Buffer N Even Odd Swapped Register" hexmask.long 0x0 0.--31. 1. "SHIFTBUFEOS,Shift Buffer" repeat.end tree.end tree.end tree "FLEXRAM" base ad:0x40028000 group.long 0x0++0x1B line.long 0x0 "TCM_CTRL,TCM CRTL Register" hexmask.long 0x0 3.--31. 1. "Reserved,Reserved" newline bitfld.long 0x0 2. "FORCE_CLK_ON,Force RAM Clock Always On" "0,1" newline bitfld.long 0x0 1. "TCM_RWAIT_EN,TCM Read Wait Mode Enable" "0: TCM read fast mode: Read RAM accesses are..,1: TCM read wait mode: Read RAM accesses are.." newline bitfld.long 0x0 0. "TCM_WWAIT_EN,TCM Write Wait Mode Enable" "0: TCM write fast mode: Write RAM accesses are..,1: TCM write wait mode: Write RAM accesses are.." line.long 0x4 "OCRAM_MAGIC_ADDR,OCRAM Magic Address Register" hexmask.long.word 0x4 18.--31. 1. "Reserved,Reserved" newline hexmask.long.tbyte 0x4 1.--17. 1. "OCRAM_MAGIC_ADDR,OCRAM Magic Address" newline bitfld.long 0x4 0. "OCRAM_WR_RD_SEL,OCRAM Write Read Select" "0: When OCRAM read access hits magic address it..,1: When OCRAM write access hits magic address it.." line.long 0x8 "DTCM_MAGIC_ADDR,DTCM Magic Address Register" hexmask.long.word 0x8 17.--31. 1. "Reserved,Reserved" newline hexmask.long.word 0x8 1.--16. 1. "DTCM_MAGIC_ADDR,DTCM Magic Address" newline bitfld.long 0x8 0. "DTCM_WR_RD_SEL,DTCM Write Read Select" "0: When DTCM read access hits magic address it will..,1: When DTCM write access hits magic address it.." line.long 0xC "ITCM_MAGIC_ADDR,ITCM Magic Address Register" hexmask.long.word 0xC 17.--31. 1. "Reserved,Reserved" newline hexmask.long.word 0xC 1.--16. 1. "ITCM_MAGIC_ADDR,ITCM Magic Address" newline bitfld.long 0xC 0. "ITCM_WR_RD_SEL,ITCM Write Read Select" "0: When ITCM read access hits magic address it will..,1: When ITCM write access hits magic address it.." line.long 0x10 "INT_STATUS,Interrupt Status Register" hexmask.long.word 0x10 18.--31. 1. "Reserved,Reserved" newline eventfld.long 0x10 17. "OCRAM_PARTIAL_WR_INT_S,OCRAM Partial Write Interrupt Status" "0: OCRAM Partial Write does not happen,1: OCRAM Partial Write happens." newline eventfld.long 0x10 16. "D1TCM_PARTIAL_WR_INT_S,D1TCM Partial Write Interrupt Status" "0: D1TCM Partial Write does not happen,1: D1TCM Partial Write happens." newline eventfld.long 0x10 15. "D0TCM_PARTIAL_WR_INT_S,D0TCM Partial Write Interrupt Status" "0: D0TCM Partial Write does not happen,1: D0TCM Partial Write happens." newline eventfld.long 0x10 14. "ITCM_PARTIAL_WR_INT_S,ITCM Partial Write Interrupt Status" "0: ITCM Partial Write does not happen,1: ITCM Partial Write happens." newline eventfld.long 0x10 13. "D1TCM_ECC_ERRS_INT,D1TCM access single-bit ECC Error Interrupt Status" "0: D1TCM single-bit ECC error does not happen,1: D1TCM single-bit ECC error happens." newline eventfld.long 0x10 12. "D1TCM_ECC_ERRM_INT,D1TCM access multi-bit ECC Error Interrupt Status" "0: D1TCM multi-bit ECC error does not happen,1: D1TCM multi-bit ECC error happens." newline eventfld.long 0x10 11. "D0TCM_ECC_ERRS_INT,D0TCM access single-bit ECC Error Interrupt Status" "0: D0TCM single-bit ECC error does not happen,1: D0TCM single-bit ECC error happens." newline eventfld.long 0x10 10. "D0TCM_ECC_ERRM_INT,D0TCM access multi-bit ECC Error Interrupt Status" "0: D0TCM multi-bit ECC error does not happen,1: D0TCM multi-bit ECC error happens." newline eventfld.long 0x10 9. "ITCM_ECC_ERRS_INT,ITCM access single-bit ECC Error Interrupt Status" "0: ITCM single-bit ECC error does not happen,1: ITCM single-bit ECC error happens." newline eventfld.long 0x10 8. "ITCM_ECC_ERRM_INT,ITCM Access multi-bit ECC Error Interrupt Status" "0: ITCM multi-bit ECC error does not happen,1: ITCM multi-bit ECC error happens." newline eventfld.long 0x10 7. "OCRAM_ECC_ERRS_INT,OCRAM access single-bit ECC Error Interrupt Status" "0: OCRAM single-bit ECC error does not happen,1: OCRAM single-bit ECC error happens." newline eventfld.long 0x10 6. "OCRAM_ECC_ERRM_INT,OCRAM access multi-bit ECC Error Interrupt Status" "0: OCRAM multi-bit ECC error does not happen,1: OCRAM multi-bit ECC error happens." newline eventfld.long 0x10 5. "OCRAM_ERR_STATUS,OCRAM Access Error Status" "0: OCRAM access error does not happen,1: OCRAM access error happens." newline eventfld.long 0x10 4. "DTCM_ERR_STATUS,DTCM Access Error Status" "0: DTCM access error does not happen,1: DTCM access error happens." newline eventfld.long 0x10 3. "ITCM_ERR_STATUS,ITCM Access Error Status" "0: ITCM access error does not happen,1: ITCM access error happens." newline eventfld.long 0x10 2. "OCRAM_MAM_STATUS,OCRAM Magic Address Match Status" "0: OCRAM did not access magic address.,1: OCRAM accessed magic address." newline eventfld.long 0x10 1. "DTCM_MAM_STATUS,DTCM Magic Address Match Status" "0: DTCM did not access magic address.,1: DTCM accessed magic address." newline eventfld.long 0x10 0. "ITCM_MAM_STATUS,ITCM Magic Address Match Status" "0: ITCM did not access magic address.,1: ITCM accessed magic address." line.long 0x14 "INT_STAT_EN,Interrupt Status Enable Register" hexmask.long.word 0x14 18.--31. 1. "Reserved,Reserved" newline bitfld.long 0x14 17. "OCRAM_PARTIAL_WR_INT_S_EN,OCRAM Partial Write Interrupt Status" "0: Masked,1: Enabled" newline bitfld.long 0x14 16. "D1TCM_PARTIAL_WR_INT_S_EN,D1TCM Partial Write Interrupt Status EN" "0: Masked,1: Enbaled" newline bitfld.long 0x14 15. "D0TCM_PARTIAL_WR_INT_S_EN,D0TCM Partial Write Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 14. "ITCM_PARTIAL_WR_INT_S_EN,ITCM Partial Write Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 13. "D1TCM_ERRS_INT_EN,D1TCM Access single-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 12. "D1TCM_ERRM_INT_EN,D1TCM Access multi-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 11. "D0TCM_ERRS_INT_EN,D0TCM Access single-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 10. "D0TCM_ERRM_INT_EN,D0TCM Access multi-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 9. "ITCM_ERRS_INT_EN,ITCM Access single-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 8. "ITCM_ERRM_INT_EN,ITCM Access multi-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 7. "OCRAM_ERRS_INT_EN,OCRAM Access single-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 6. "OCRAM_ERRM_INT_EN,OCRAM Access multi-bit ECC Error Interrupt Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 5. "OCRAM_ERR_STAT_EN,OCRAM Access Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 4. "DTCM_ERR_STAT_EN,DTCM Access Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 3. "ITCM_ERR_STAT_EN,ITCM Access Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 2. "OCRAM_MAM_STAT_EN,OCRAM Magic Address Match Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 1. "DTCM_MAM_STAT_EN,DTCM Magic Address Match Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x14 0. "ITCM_MAM_STAT_EN,ITCM Magic Address Match Status Enable" "0: Masked,1: Enabled" line.long 0x18 "INT_SIG_EN,Interrupt Enable Register" hexmask.long.word 0x18 18.--31. 1. "Reserved,Reserved" newline bitfld.long 0x18 17. "OCRAM_PARTIAL_WR_INT_SIG_EN,OCRAM Partial Write Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 16. "D1TCM_PARTIAL_WR_INT_SIG_EN,D1TCM Partial Write Interrupt Signal Enable EN" "0: Masked,1: Enbaled" newline bitfld.long 0x18 15. "D0TCM_PARTIAL_WR_INT_SIG_EN,D0TCM Partial Write Interrupt Signal Enable Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 14. "ITCM_PARTIAL_WR_INT_SIG_EN,ITCM Partial Write Interrupt Signal Enable Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 13. "D1TCM_ERRS_INT_SIG_EN,D1TCM Access single-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 12. "D1TCM_ERRM_INT_SIG_EN,D1TCM Access multi-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 11. "D0TCM_ERRS_INT_SIG_EN,D0TCM Access single-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 10. "D0TCM_ERRM_INT_SIG_EN,D0TCM Access multi-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 9. "ITCM_ERRS_INT_SIG_EN,ITCM Access single-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 8. "ITCM_ERRM_INT_SIG_EN,ITCM Access multi-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 7. "OCRAM_ERRS_INT_SIG_EN,OCRAM Access single-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 6. "OCRAM_ERRM_INT_SIG_EN,OCRAM Access multi-bit ECC Error Interrupt Signal Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 5. "OCRAM_ERR_SIG_EN,OCRAM Access Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 4. "DTCM_ERR_SIG_EN,DTCM Access Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 3. "ITCM_ERR_SIG_EN,ITCM Access Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 2. "OCRAM_MAM_SIG_EN,OCRAM Magic Address Match Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 1. "DTCM_MAM_SIG_EN,DTCM Magic Address Match Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0x18 0. "ITCM_MAM_SIG_EN,ITCM Magic Address Match Interrupt Enable" "0: Masked,1: Enabled" rgroup.long 0x1C++0x6F line.long 0x0 "OCRAM_ECC_SINGLE_ERROR_INFO,OCRAM single-bit ECC Error Information Register" hexmask.long.word 0x0 16.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x0 8.--15. 1. "OCRAM_ECCS_ERRED_SYN,corresponding ECC syndrome of OCRAM single-bit ECC error" newline hexmask.long.byte 0x0 0.--7. 1. "OCRAM_ECCS_ERRED_ECC,corresponding ECC cipher of OCRAM single-bit ECC error" line.long 0x4 "OCRAM_ECC_SINGLE_ERROR_ADDR,OCRAM single-bit ECC Error Address Register" hexmask.long 0x4 0.--31. 1. "OCRAM_ECCS_ERRED_ADDR,OCRAM single-bit ECC error address" line.long 0x8 "OCRAM_ECC_SINGLE_ERROR_DATA_LSB,OCRAM single-bit ECC Error Data Register" hexmask.long 0x8 0.--31. 1. "OCRAM_ECCS_ERRED_DATA_LSB,OCRAM single-bit ECC error data [31:0]" line.long 0xC "OCRAM_ECC_SINGLE_ERROR_DATA_MSB,OCRAM single-bit ECC Error Data Register" hexmask.long 0xC 0.--31. 1. "OCRAM_ECCS_ERRED_DATA_MSB,OCRAM single-bit ECC error data [63:32]" line.long 0x10 "OCRAM_ECC_MULTI_ERROR_INFO,OCRAM multi-bit ECC Error Information Register" hexmask.long.tbyte 0x10 8.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x10 0.--7. 1. "OCRAM_ECCM_ERRED_ECC,OCRAM multi-bit ECC error corresponding ECC value" line.long 0x14 "OCRAM_ECC_MULTI_ERROR_ADDR,OCRAM multi-bit ECC Error Address Register" hexmask.long 0x14 0.--31. 1. "OCRAM_ECCM_ERRED_ADDR,OCRAM multi-bit ECC error address" line.long 0x18 "OCRAM_ECC_MULTI_ERROR_DATA_LSB,OCRAM multi-bit ECC Error Data Register" hexmask.long 0x18 0.--31. 1. "OCRAM_ECCM_ERRED_DATA_LSB,OCRAM multi-bit ECC error data [31:0]" line.long 0x1C "OCRAM_ECC_MULTI_ERROR_DATA_MSB,OCRAM multi-bit ECC Error Data Register" hexmask.long 0x1C 0.--31. 1. "OCRAM_ECCM_ERRED_DATA_MSB,OCRAM multi-bit ECC error data [63:32]" line.long 0x20 "ITCM_ECC_SINGLE_ERROR_INFO,ITCM single-bit ECC Error Information Register" hexmask.long.word 0x20 20.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x20 12.--19. 1. "ITCM_ECCS_EFSYN,ITCM single-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x20 8.--11. 1. "ITCM_ECCS_EFPRT,ITCM single-bit ECC error corresponding TCM_PRIV." newline hexmask.long.byte 0x20 4.--7. 1. "ITCM_ECCS_EFMST,ITCM single-bit ECC error corresponding TCM_MASTER." newline bitfld.long 0x20 1.--3. "ITCM_ECCS_EFSIZ,ITCM single-bit ECC error corresponding TCM size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x20 0. "ITCM_ECCS_EFW,ITCM single-bit ECC error corresponding TCM_WR value." "0,1" line.long 0x24 "ITCM_ECC_SINGLE_ERROR_ADDR,ITCM single-bit ECC Error Address Register" hexmask.long 0x24 0.--31. 1. "ITCM_ECCS_ERRED_ADDR,ITCM single-bit ECC error address" line.long 0x28 "ITCM_ECC_SINGLE_ERROR_DATA_LSB,ITCM single-bit ECC Error Data Register" hexmask.long 0x28 0.--31. 1. "ITCM_ECCS_ERRED_DATA_LSB,ITCM single-bit ECC error data [31:0]" line.long 0x2C "ITCM_ECC_SINGLE_ERROR_DATA_MSB,ITCM single-bit ECC Error Data Register" hexmask.long 0x2C 0.--31. 1. "ITCM_ECCS_ERRED_DATA_MSB,ITCM single-bit ECC error data [63:32]" line.long 0x30 "ITCM_ECC_MULTI_ERROR_INFO,ITCM multi-bit ECC Error Information Register" hexmask.long.word 0x30 20.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x30 12.--19. 1. "ITCM_ECCM_EFSYN,ITCM multi-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x30 8.--11. 1. "ITCM_ECCM_EFPRT,ITCM multi-bit ECC error corresponding TCM_PRIV" newline hexmask.long.byte 0x30 4.--7. 1. "ITCM_ECCM_EFMST,ITCM multi-bit ECC error corresponding TCM_MASTER" newline bitfld.long 0x30 1.--3. "ITCM_ECCM_EFSIZ,ITCM multi-bit ECC error corresponding tcm access size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x30 0. "ITCM_ECCM_EFW,ITCM multi-bit ECC error corresponding TCM_WR value" "0,1" line.long 0x34 "ITCM_ECC_MULTI_ERROR_ADDR,ITCM multi-bit ECC Error Address Register" hexmask.long 0x34 0.--31. 1. "ITCM_ECCM_ERRED_ADDR,ITCM multi-bit ECC error address" line.long 0x38 "ITCM_ECC_MULTI_ERROR_DATA_LSB,ITCM multi-bit ECC Error Data Register" hexmask.long 0x38 0.--31. 1. "ITCM_ECCM_ERRED_DATA_LSB,ITCM multi-bit ECC error data [31:0]" line.long 0x3C "ITCM_ECC_MULTI_ERROR_DATA_MSB,ITCM multi-bit ECC Error Data Register" hexmask.long 0x3C 0.--31. 1. "ITCM_ECCM_ERRED_DATA_MSB,ITCM multi-bit ECC error data [63:32]" line.long 0x40 "D0TCM_ECC_SINGLE_ERROR_INFO,D0TCM single-bit ECC Error Information Register" hexmask.long.word 0x40 19.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x40 12.--18. 1. "D0TCM_ECCS_EFSYN,D0TCM single-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x40 8.--11. 1. "D0TCM_ECCS_EFPRT,D0TCM single-bit ECC error corresponding TCM_PRIV" newline hexmask.long.byte 0x40 4.--7. 1. "D0TCM_ECCS_EFMST,D0TCM single-bit ECC error corresponding TCM_MASTER" newline bitfld.long 0x40 1.--3. "D0TCM_ECCS_EFSIZ,D0TCM single-bit ECC error corresponding tcm access size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x40 0. "D0TCM_ECCS_EFW,D0TCM single-bit ECC error corresponding TCM_WR value" "0,1" line.long 0x44 "D0TCM_ECC_SINGLE_ERROR_ADDR,D0TCM single-bit ECC Error Address Register" hexmask.long 0x44 0.--31. 1. "D0TCM_ECCS_ERRED_ADDR,D0TCM single-bit ECC error address" line.long 0x48 "D0TCM_ECC_SINGLE_ERROR_DATA,D0TCM single-bit ECC Error Data Register" hexmask.long 0x48 0.--31. 1. "D0TCM_ECCS_ERRED_DATA,D0TCM single-bit ECC error data" line.long 0x4C "D0TCM_ECC_MULTI_ERROR_INFO,D0TCM multi-bit ECC Error Information Register" hexmask.long.word 0x4C 19.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x4C 12.--18. 1. "D0TCM_ECCM_EFSYN,D0TCM multi-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x4C 8.--11. 1. "D0TCM_ECCM_EFPRT,D0TCM multi-bit ECC error corresponding TCM_PRIV" newline hexmask.long.byte 0x4C 4.--7. 1. "D0TCM_ECCM_EFMST,D0TCM multi-bit ECC error corresponding TCM_MASTER" newline bitfld.long 0x4C 1.--3. "D0TCM_ECCM_EFSIZ,D0TCM multi-bit ECC error corresponding tcm access size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4C 0. "D0TCM_ECCM_EFW,D0TCM multi-bit ECC error corresponding TCM_WR value" "0,1" line.long 0x50 "D0TCM_ECC_MULTI_ERROR_ADDR,D0TCM multi-bit ECC Error Address Register" hexmask.long 0x50 0.--31. 1. "D0TCM_ECCM_ERRED_ADDR,D0TCM multi-bit ECC error address" line.long 0x54 "D0TCM_ECC_MULTI_ERROR_DATA,D0TCM multi-bit ECC Error Data Register" hexmask.long 0x54 0.--31. 1. "D0TCM_ECCM_ERRED_DATA,D0TCM multi-bit ECC error data" line.long 0x58 "D1TCM_ECC_SINGLE_ERROR_INFO,D1TCM single-bit ECC Error Information Register" hexmask.long.word 0x58 19.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x58 12.--18. 1. "D1TCM_ECCS_EFSYN,D1TCM single-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x58 8.--11. 1. "D1TCM_ECCS_EFPRT,D1TCM single-bit ECC error corresponding TCM_PRIV" newline hexmask.long.byte 0x58 4.--7. 1. "D1TCM_ECCS_EFMST,D1TCM single-bit ECC error corresponding TCM_MASTER" newline bitfld.long 0x58 1.--3. "D1TCM_ECCS_EFSIZ,D1TCM single-bit ECC error corresponding tcm access size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x58 0. "D1TCM_ECCS_EFW,D1TCM single-bit ECC error corresponding TCM_WR value" "0,1" line.long 0x5C "D1TCM_ECC_SINGLE_ERROR_ADDR,D1TCM single-bit ECC Error Address Register" hexmask.long 0x5C 0.--31. 1. "D1TCM_ECCS_ERRED_ADDR,D1TCM single-bit ECC error address" line.long 0x60 "D1TCM_ECC_SINGLE_ERROR_DATA,D1TCM single-bit ECC Error Data Register" hexmask.long 0x60 0.--31. 1. "D1TCM_ECCS_ERRED_DATA,D1TCM single-bit ECC error data" line.long 0x64 "D1TCM_ECC_MULTI_ERROR_INFO,D1TCM multi-bit ECC Error Information Register" hexmask.long.word 0x64 19.--31. 1. "Reserved,Reserved" newline hexmask.long.byte 0x64 12.--18. 1. "D1TCM_ECCM_EFSYN,D1TCM multi-bit ECC error corresponding syndrome" newline hexmask.long.byte 0x64 8.--11. 1. "D1TCM_ECCM_EFPRT,D1TCM multi-bit ECC error corresponding TCM_PRIV" newline hexmask.long.byte 0x64 4.--7. 1. "D1TCM_ECCM_EFMST,D1TCM multi-bit ECC error corresponding TCM_MASTER" newline bitfld.long 0x64 1.--3. "D1TCM_ECCM_EFSIZ,D1TCM multi-bit ECC error corresponding tcm access size" "0,1,2,3,4,5,6,7" newline bitfld.long 0x64 0. "D1TCM_ECCM_EFW,D1TCM multi-bit ECC error corresponding TCM_WR value" "0,1" line.long 0x68 "D1TCM_ECC_MULTI_ERROR_ADDR,D1TCM multi-bit ECC Error Address Register" hexmask.long 0x68 0.--31. 1. "D1TCM_ECCM_ERRED_ADDR,D1TCM multi-bit ECC error address" line.long 0x6C "D1TCM_ECC_MULTI_ERROR_DATA,D1TCM multi-bit ECC Error Data Register" hexmask.long 0x6C 0.--31. 1. "D1TCM_ECCM_ERRED_DATA,D1TCM multi-bit ECC error data" group.long 0x108++0x3 line.long 0x0 "FLEXRAM_CTRL,FlexRAM feature Control register" hexmask.long 0x0 6.--31. 1. "Reserved,Reserved" newline bitfld.long 0x0 5. "TCM_ECC_EN,TCM ECC enable" "0,1" newline bitfld.long 0x0 4. "OCRAM_ECC_EN,OCRAM ECC enable" "0,1" newline bitfld.long 0x0 3. "OCRAM_WRADDR_PIPELINE_EN,Write Address Pipeline Enable" "0,1" newline bitfld.long 0x0 2. "OCRAM_WRDATA_PIPELINE_EN,Write Data Pipeline Enable" "0,1" newline bitfld.long 0x0 1. "OCRAM_RADDR_PIPELINE_EN,Read Address Pipeline Enable" "0,1" newline bitfld.long 0x0 0. "OCRAM_RDATA_WAIT_EN,Read Data Wait Enable" "0,1" rgroup.long 0x10C++0x3 line.long 0x0 "OCRAM_PIPELINE_STATUS,OCRAM Pipeline Status register" hexmask.long 0x0 4.--31. 1. "Reserved,Reserved" newline bitfld.long 0x0 3. "OCRAM_WRADDR_PIPELINE_EN_UPDATA_PENDING,Write Address Pipeline Enable Pending" "0,1" newline bitfld.long 0x0 2. "OCRAM_WRDATA_PIPELINE_EN_UPDATA_PENDING,Write Data Pipeline Enable Pending" "0,1" newline bitfld.long 0x0 1. "OCRAM_RADDR_PIPELINE_EN_UPDATA_PENDING,Read Address Pipeline Enable Pending" "0,1" newline bitfld.long 0x0 0. "OCRAM_RDATA_WAIT_EN_UPDATA_PENDING,Read Data Wait Enable Pending" "0,1" tree.end tree "FLEXSPI" base ad:0x0 tree "FLEXSPI1" base ad:0x400CC000 group.long 0x0++0x3F line.long 0x0 "MCR0,Module Control Register 0" hexmask.long.byte 0x0 24.--31. 1. "AHBGRANTWAIT,Timeout wait cycle for AHB command grant." newline hexmask.long.byte 0x0 16.--23. 1. "IPGRANTWAIT,Time out wait cycle for IP command grant." newline bitfld.long 0x0 14. "SCKFREERUNEN,This bit is used to force SCLK output free-running. For FPGA applications external device may use SCLK as reference clock to its internal PLL. If SCLK free-running is enabled data sampling with loopback clock from SCLK pad is not supported.." "0: Disable.,1: Enable." newline bitfld.long 0x0 13. "COMBINATIONEN,This bit is to support Flash Octal mode access by combining Port A and B Data pins (A_DATA[3:0] and B_DATA[3:0]) when Port A and Port B are of 4 bit data width." "0: Disable.,1: Enable." newline bitfld.long 0x0 12. "DOZEEN,Doze mode enable bit" "0: Doze mode support disabled. AHB clock and serial..,1: Doze mode support enabled. AHB clock and serial.." newline bitfld.long 0x0 11. "HSEN,Half Speed Serial Flash access Enable." "0: Disable divide by 2 of serial flash clock for..,1: Enable divide by 2 of serial flash clock for.." newline bitfld.long 0x0 8.--10. "SERCLKDIV,The serial root clock could be divided inside FlexSPI . Refer Clocks chapter for more details on clocking." "0: Divided by 1,1: Divided by 2,2: Divided by 3,3: Divided by 4,4: Divided by 5,5: Divided by 6,6: Divided by 7,7: Divided by 8" newline bitfld.long 0x0 7. "ATDFEN,Enable AHB bus Write Access to IP TX FIFO." "0: IP TX FIFO should be written by IP Bus. AHB Bus..,1: IP TX FIFO should be written by AHB Bus. IP Bus.." newline bitfld.long 0x0 6. "ARDFEN,Enable AHB bus Read Access to IP RX FIFO." "0: IP RX FIFO should be read by IP Bus. AHB Bus..,1: IP RX FIFO should be read by AHB Bus. IP Bus.." newline bitfld.long 0x0 4.--5. "RXCLKSRC,Sample Clock source selection for Flash Reading" "0: Dummy Read strobe generated by FlexSPI..,1: Dummy Read strobe generated by FlexSPI..,?,3: Flash provided Read strobe and input from DQS pad" newline bitfld.long 0x0 1. "MDIS,Module Disable" "0,1" newline bitfld.long 0x0 0. "SWRESET,Software Reset" "0,1" line.long 0x4 "MCR1,Module Control Register 1" hexmask.long.word 0x4 16.--31. 1. "SEQWAIT,Command Sequence Execution will timeout and abort after SEQWAIT * 1024 Serial Root Clock cycles" newline hexmask.long.word 0x4 0.--15. 1. "AHBBUSWAIT,AHB Read/Write access to Serial Flash Memory space will timeout if not data received from Flash or data not transmitted after AHBBUSWAIT * 1024 ahb clock cycles AHB Bus will get an error response" line.long 0x8 "MCR2,Module Control Register 2" hexmask.long.byte 0x8 24.--31. 1. "RESUMEWAIT,Wait cycle (in AHB clock cycle) for idle state before suspended command sequence resumed." newline bitfld.long 0x8 19. "SCKBDIFFOPT,B_SCLK pad can be used as A_SCLK differential clock output (inverted clock to A_SCLK). In this case port B flash access is not available. After changing the value of this field MCR0[SWRESET] should be set." "0: B_SCLK pad is used as port B SCLK clock output.,1: B_SCLK pad is used as port A SCLK inverted clock.." newline bitfld.long 0x8 15. "SAMEDEVICEEN,All external devices are same devices (both in types and size) for A1/A2/B1/B2." "0: In Individual mode..,1: FLSHA1CR0/FLSHA1CR1/FLSHA1CR2 register settings.." newline bitfld.long 0x8 11. "CLRAHBBUFOPT,This bit determines whether AHB RX Buffer and AHB TX Buffer will be cleaned automatically when FlexSPI returns STOP mode ACK. Software should set this bit if AHB RX Buffer or AHB TX Buffer will be powered off in STOP mode. Otherwise AHB read.." "0: AHB RX/TX Buffer will not be cleaned..,1: AHB RX/TX Buffer will be cleaned automatically.." line.long 0xC "AHBCR,AHB Bus Control Register" bitfld.long 0xC 20.--21. "ALIGNMENT,Decides all AHB read/write boundary. All access cross the boundary will be divided into smaller sub accesses." "0: No limit,1: 1 KBytes,2: 512 Bytes,3: 256 Bytes" newline bitfld.long 0xC 19. "ECCSWAPEN,ECC Read data swap function" "0: rdata send to ecc check without swap.,1: rdata send to ecc ehck with swap." newline bitfld.long 0xC 18. "HMSTRIDREMAP,AHB Master ID Remapping enable" "0,1" newline bitfld.long 0xC 17. "ECCMULTIERRCLR,AHB ECC Multi bits ERR CLR" "0,1" newline bitfld.long 0xC 16. "ECCSINGLEERRCLR,AHB ECC Single bit ERR CLR" "0,1" newline bitfld.long 0xC 15. "KEYECCEN,OTFAD KEY BLOC ECC Enable" "0: AHB KEY ECC check disabled,1: AHB KEY ECC check enabled" newline bitfld.long 0xC 13.--14. "SPLIT_LIMIT,AHB SPLIT SIZE" "0: AHB Split Size=8bytes,1: AHB Split Size=16bytes,2: AHB Split Size=32bytes,3: AHB Split Size=64bytes" newline bitfld.long 0xC 12. "SPLITEN,AHB transaction SPLIT" "0: AHB Split disabled,1: AHB Split enabled" newline bitfld.long 0xC 11. "ECCEN,AHB Read ECC Enable" "0: AHB read ECC check disabled,1: AHB read ECC check enabled" newline bitfld.long 0xC 10. "READSZALIGN,AHB Read Size Alignment" "0: AHB read size will be decided by other register..,1: AHB read size to up size to 8 bytes aligned no.." newline bitfld.long 0xC 6. "READADDROPT,AHB Read Address option bit. This option bit is intend to remove AHB burst start address alignment limitation." "0: There is AHB read burst start address alignment..,1: There is no AHB read burst start address.." newline bitfld.long 0xC 5. "PREFETCHEN,AHB Read Prefetch Enable." "0,1" newline bitfld.long 0xC 4. "BUFFERABLEEN,Enable AHB bus bufferable write access support. This field affects the last beat of AHB write access refer for more details about AHB bufferable write." "0: Disabled. For all AHB write access (no matter..,1: Enabled. For AHB bufferable write access FlexSPI.." newline bitfld.long 0xC 3. "CACHABLEEN,Enable AHB bus cachable read access support." "0: Disabled. When there is AHB bus cachable read..,1: Enabled. When there is AHB bus cachable read.." newline bitfld.long 0xC 1. "CLRAHBRXBUF,Clear the status/pointers of AHB RX Buffer. Auto-cleared." "0,1" newline bitfld.long 0xC 0. "APAREN,Parallel mode enabled for AHB triggered Command (both read and write) ." "0: Flash will be accessed in Individual mode.,1: Flash will be accessed in Parallel mode." line.long 0x10 "INTEN,Interrupt Enable Register" bitfld.long 0x10 16. "IPCMDSECUREVIOEN,IP command security violation interrupt enable." "0,1" newline bitfld.long 0x10 15. "ECCSINGLEERREN,ECC single bit error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 14. "ECCMULTIERREN,ECC multi bits error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 13. "KEYERROREN,OTFAD key blob processing error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 12. "KEYDONEEN,OTFAD key blob processing done interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 11. "SEQTIMEOUTEN,Sequence execution timeout interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 10. "AHBBUSERROREN,AHB Bus error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 9. "SCKSTOPBYWREN,SCLK is stopped during command sequence because Async TX FIFO empty interrupt enable." "0,1" newline bitfld.long 0x10 8. "SCKSTOPBYRDEN,SCLK is stopped during command sequence because Async RX FIFO full interrupt enable." "0,1" newline bitfld.long 0x10 6. "IPTXWEEN,IP TX FIFO WaterMark empty interrupt enable." "0,1" newline bitfld.long 0x10 5. "IPRXWAEN,IP RX FIFO WaterMark available interrupt enable." "0,1" newline bitfld.long 0x10 4. "AHBCMDERREN,AHB triggered Command Sequences Error Detected interrupt enable." "0,1" newline bitfld.long 0x10 3. "IPCMDERREN,IP triggered Command Sequences Error Detected interrupt enable." "0,1" newline bitfld.long 0x10 2. "AHBCMDGEEN,AHB triggered Command Sequences Grant Timeout interrupt enable." "0,1" newline bitfld.long 0x10 1. "IPCMDGEEN,IP triggered Command Sequences Grant Timeout interrupt enable." "0,1" newline bitfld.long 0x10 0. "IPCMDDONEEN,IP triggered Command Sequences Execution finished interrupt enable." "0,1" line.long 0x14 "INTR,Interrupt Register" eventfld.long 0x14 16. "IPCMDSECUREVIO,IP command security violation interrupt." "0,1" newline eventfld.long 0x14 15. "ECCSINGLEERR,ECC single bit error interrupt." "0,1" newline eventfld.long 0x14 14. "ECCMULTIERR,ECC multi bits error interrupt." "0,1" newline rbitfld.long 0x14 13. "KEYERROR,OTFAD key blob processing error interrupt." "0,1" newline eventfld.long 0x14 12. "KEYDONE,OTFAD key blob processing done interrupt." "0,1" newline eventfld.long 0x14 11. "SEQTIMEOUT,Sequence execution timeout interrupt." "0,1" newline eventfld.long 0x14 10. "AHBBUSERROR,AHB Bus timeout or AHB bus illegal access Flash during OTFAD key blob processing interrupt." "0,1" newline eventfld.long 0x14 9. "SCKSTOPBYWR,SCLK is stopped during command sequence because Async TX FIFO empty interrupt." "0,1" newline eventfld.long 0x14 8. "SCKSTOPBYRD,SCLK is stopped during command sequence because Async RX FIFO full interrupt." "0,1" newline eventfld.long 0x14 6. "IPTXWE,IP TX FIFO watermark empty interrupt." "0,1" newline eventfld.long 0x14 5. "IPRXWA,IP RX FIFO watermark available interrupt." "0,1" newline eventfld.long 0x14 4. "AHBCMDERR,AHB triggered Command Sequences Error Detected interrupt. When an error detected for AHB command this command will be ignored and not executed at all." "0,1" newline eventfld.long 0x14 3. "IPCMDERR,IP triggered Command Sequences Error Detected interrupt. When an error detected for IP command this command will be ignored and not executed at all." "0,1" newline eventfld.long 0x14 2. "AHBCMDGE,AHB triggered Command Sequences Grant Timeout interrupt." "0,1" newline eventfld.long 0x14 1. "IPCMDGE,IP triggered Command Sequences Grant Timeout interrupt." "0,1" newline eventfld.long 0x14 0. "IPCMDDONE,IP triggered Command Sequences Execution finished interrupt. This interrupt is also generated when there is IPCMDGE or IPCMDERR interrupt generated." "0,1" line.long 0x18 "LUTKEY,LUT Key Register" hexmask.long 0x18 0.--31. 1. "KEY,The Key to lock or unlock LUT." line.long 0x1C "LUTCR,LUT Control Register" bitfld.long 0x1C 2. "PROTECT,LUT protection" "0,1" newline bitfld.long 0x1C 1. "UNLOCK,Unlock LUT" "0,1" newline bitfld.long 0x1C 0. "LOCK,Lock LUT" "0,1" line.long 0x20 "AHBRXBUF0CR0,AHB RX Buffer 0 Control Register 0" bitfld.long 0x20 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x20 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x20 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x20 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x20 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x24 "AHBRXBUF1CR0,AHB RX Buffer 1 Control Register 0" bitfld.long 0x24 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x24 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x24 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x24 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x24 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x28 "AHBRXBUF2CR0,AHB RX Buffer 2 Control Register 0" bitfld.long 0x28 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x28 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x28 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x28 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x28 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x2C "AHBRXBUF3CR0,AHB RX Buffer 3 Control Register 0" bitfld.long 0x2C 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x2C 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x2C 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x2C 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x2C 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x30 "AHBRXBUF4CR0,AHB RX Buffer 4 Control Register 0" bitfld.long 0x30 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x30 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x30 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x30 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x30 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x34 "AHBRXBUF5CR0,AHB RX Buffer 5 Control Register 0" bitfld.long 0x34 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x34 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x34 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x34 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x34 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x38 "AHBRXBUF6CR0,AHB RX Buffer 6 Control Register 0" bitfld.long 0x38 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x38 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x38 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x38 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x38 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x3C "AHBRXBUF7CR0,AHB RX Buffer 7 Control Register 0" bitfld.long 0x3C 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x3C 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x3C 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x3C 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x3C 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." group.long 0x60++0xF line.long 0x0 "FLSHA1CR0,Flash Control Register 0" bitfld.long 0x0 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x0 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x0 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0x4 "FLSHA2CR0,Flash Control Register 0" bitfld.long 0x4 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x4 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x4 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0x8 "FLSHB1CR0,Flash Control Register 0" bitfld.long 0x8 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x8 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x8 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0xC "FLSHB2CR0,Flash Control Register 0" bitfld.long 0xC 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0xC 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0xC 0.--22. 1. "FLSHSZ,Flash Size in KByte." repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x70)++0x3 line.long 0x0 "FLSHCR1$1,Flash Control Register 1" hexmask.long.word 0x0 16.--31. 1. "CSINTERVAL,This field is used to set the minimum interval between flash device Chip selection deassertion and flash device Chip selection assertion. If external flash has a limitation on the interval between command sequences this field should be set.." newline bitfld.long 0x0 15. "CSINTERVALUNIT,CS interval unit" "0: The CS interval unit is 1 serial clock cycle,1: The CS interval unit is 256 serial clock cycle" newline hexmask.long.byte 0x0 11.--14. 1. "CAS,Column Address Size." newline bitfld.long 0x0 10. "WA,Word Addressable." "0,1" newline hexmask.long.byte 0x0 5.--9. 1. "TCSH,Serial Flash CS Hold time." newline hexmask.long.byte 0x0 0.--4. 1. "TCSS,Serial Flash CS setup time." repeat.end repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x80)++0x3 line.long 0x0 "FLSHCR2$1,Flash Control Register 2" bitfld.long 0x0 31. "CLRINSTRPTR,Clear the instruction pointer which is internally saved pointer by JMP_ON_CS. Refer Programmable Sequence Engine for details." "0,1" newline bitfld.long 0x0 28.--30. "AWRWAITUNIT,AWRWAIT unit" "0: The AWRWAIT unit is 2 ahb clock cycle,1: The AWRWAIT unit is 8 ahb clock cycle,2: The AWRWAIT unit is 32 ahb clock cycle,3: The AWRWAIT unit is 128 ahb clock cycle,4: The AWRWAIT unit is 512 ahb clock cycle,5: The AWRWAIT unit is 2048 ahb clock cycle,6: The AWRWAIT unit is 8192 ahb clock cycle,7: The AWRWAIT unit is 32768 ahb clock cycle" newline hexmask.long.word 0x0 16.--27. 1. "AWRWAIT,For certain devices (such as FPGA) it need some time to write data into internal memory after the command sequences finished on FlexSPI interface" newline bitfld.long 0x0 13.--15. "AWRSEQNUM,Sequence Number for AHB Write triggered Command." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 8.--11. 1. "AWRSEQID,Sequence Index for AHB Write triggered Command." newline bitfld.long 0x0 5.--7. "ARDSEQNUM,Sequence Number for AHB Read triggered Command in LUT." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--3. 1. "ARDSEQID,Sequence Index for AHB Read triggered Command in LUT." repeat.end group.long 0x94++0x3 line.long 0x0 "FLSHCR4,Flash Control Register 4" bitfld.long 0x0 11. "PAR_ADDR_ADJ_DIS,Disable the address shift logic for lower density of 16 bit PSRAM." "0,1" newline bitfld.long 0x0 9.--10. "PAR_WM,Enable APMEM 16 bit write mask function bit 9 for A1-B1 pair bit 10 for A2-B2 pair." "?,1: B1 pair,2: B2 pair,?" newline bitfld.long 0x0 3. "WMENB,Write mask enable bit for flash device on port B. When write mask function is needed for memory device on port B this bit must be set." "0: Write mask is disabled DQS(RWDS) pin will be..,1: Write mask is enabled DQS(RWDS) pin will be.." newline bitfld.long 0x0 2. "WMENA,Write mask enable bit for flash device on port A. When write mask function is needed for memory device on port A this bit must be set." "0: Write mask is disabled DQS(RWDS) pin will be..,1: Write mask is enabled DQS(RWDS) pin will be.." newline bitfld.long 0x0 1. "WMOPT2,Write mask option bit 2. When using AP memory This option bit could be used to remove AHB write burst minimal length limitation. When using this bit WMOPT1 should also be set." "0: DQS pin will be used as Write Mask when writing..,1: DQS pin will not be used as Write Mask when.." newline bitfld.long 0x0 0. "WMOPT1,Write mask option bit 1. This option bit could be used to remove AHB write burst start address alignment limitation." "0: DQS pin will be used as Write Mask when writing..,1: DQS pin will not be used as Write Mask when.." group.long 0xA0++0x7 line.long 0x0 "IPCR0,IP Control Register 0" hexmask.long 0x0 0.--31. 1. "SFAR,Serial Flash Address for IP command." line.long 0x4 "IPCR1,IP Control Register 1" bitfld.long 0x4 31. "IPAREN,Parallel mode Enabled for IP command." "0: Flash will be accessed in Individual mode.,1: Flash will be accessed in Parallel mode." newline bitfld.long 0x4 24.--26. "ISEQNUM,Sequence Number for IP command: ISEQNUM+1." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 16.--19. 1. "ISEQID,Sequence Index in LUT for IP command." newline hexmask.long.word 0x4 0.--15. 1. "IDATSZ,Flash Read/Program Data Size (in Bytes) for IP command." group.long 0xB0++0x3 line.long 0x0 "IPCMD,IP Command Register" bitfld.long 0x0 0. "TRG,Setting this bit will trigger an IP Command." "0,1" group.long 0xB8++0x7 line.long 0x0 "IPRXFCR,IP RX FIFO Control Register" hexmask.long.byte 0x0 2.--6. 1. "RXWMRK,Watermark level is (RXWMRK+1)*64 Bits." newline bitfld.long 0x0 1. "RXDMAEN,IP RX FIFO reading by DMA enabled." "0: IP RX FIFO would be read by processor.,1: IP RX FIFO would be read by DMA." newline bitfld.long 0x0 0. "CLRIPRXF,Clear all valid data entries in IP RX FIFO." "0,1" line.long 0x4 "IPTXFCR,IP TX FIFO Control Register" hexmask.long.byte 0x4 2.--6. 1. "TXWMRK,Watermark level is (TXWMRK+1)*64 Bits." newline bitfld.long 0x4 1. "TXDMAEN,IP TX FIFO filling by DMA enabled." "0: IP TX FIFO would be filled by processor.,1: IP TX FIFO would be filled by DMA." newline bitfld.long 0x4 0. "CLRIPTXF,Clear all valid data entries in IP TX FIFO." "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xC0)++0x3 line.long 0x0 "DLLCR$1,DLL Control Register 0" hexmask.long.byte 0x0 9.--14. 1. "OVRDVAL,Slave clock delay line delay cell number selection override value." newline bitfld.long 0x0 8. "OVRDEN,Slave clock delay line delay cell number selection override enable." "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "SLVDLYTARGET,The delay target for slave delay line is: ((SLVDLYTARGET+1) * 1/32 * clock cycle of reference clock (serial root clock). If serial root clock is >= 100 MHz DLLEN set to 0x1 OVRDEN set to =0x0 then SLVDLYTARGET setting of 0xF is recommended." newline bitfld.long 0x0 1. "DLLRESET,Software could force a reset on DLL by setting this field to 0x1. This will cause the DLL to lose lock and re-calibrate to detect an ref_clock half period phase shift. The reset action is edge triggered so software need to clear this bit after.." "0,1" newline bitfld.long 0x0 0. "DLLEN,DLL calibration enable." "0,1" repeat.end rgroup.long 0xD0++0x27 line.long 0x0 "MISCCR4,Misc Control Register 4" hexmask.long 0x0 0.--31. 1. "AHBADDRESS,AHB bus address that trigger the current ECC multi bits error interrupt." line.long 0x4 "MISCCR5,Misc Control Register 5" hexmask.long 0x4 0.--31. 1. "ECCSINGLEERRORCORR,ECC single bit error correction indication." line.long 0x8 "MISCCR6,Misc Control Register 6" hexmask.long 0x8 2.--31. 1. "ADDRESS,ECC single error address" newline bitfld.long 0x8 1. "HIT,ECC single error information Hit" "0,1" newline bitfld.long 0x8 0. "VALID,ECC single error information Valid" "0,1" line.long 0xC "MISCCR7,Misc Control Register 7" hexmask.long 0xC 2.--31. 1. "ADDRESS,ECC multi error address" newline bitfld.long 0xC 1. "HIT,ECC multi error information Hit" "0,1" newline bitfld.long 0xC 0. "VALID,ECC multi error information Valid" "0,1" line.long 0x10 "STS0,Status Register 0" bitfld.long 0x10 2.--3. "ARBCMDSRC,This status field indicates the trigger source of current command sequence granted by arbitrator. This field value is meaningless when ARB_CTL is not busy (STS0[ARBIDLE]=0x1)." "0: Triggered by AHB read command (triggered by AHB..,1: Triggered by AHB write command (triggered by AHB..,2: Triggered by IP command (triggered by setting..,3: Triggered by suspended command (resumed)." newline bitfld.long 0x10 1. "ARBIDLE,This status bit indicates the state machine in ARB_CTL is busy and there is command sequence granted by arbitrator and not finished yet on FlexSPI interface. When ARB_CTL state (ARBIDLE=0x1) is idle there will be no transaction on FlexSPI.." "0,1" newline bitfld.long 0x10 0. "SEQIDLE,This status bit indicates the state machine in SEQ_CTL is idle and there is command sequence executing on FlexSPI interface." "0,1" line.long 0x14 "STS1,Status Register 1" hexmask.long.byte 0x14 24.--27. 1. "IPCMDERRCODE,Indicates the Error Code when IP command Error detected. This field will be cleared when INTR[IPCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 16.--19. 1. "IPCMDERRID,Indicates the sequence Index when IP command error detected. This field will be cleared when INTR[IPCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 8.--11. 1. "AHBCMDERRCODE,Indicates the Error Code when AHB command Error detected. This field will be cleared when INTR[AHBCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 0.--3. 1. "AHBCMDERRID,Indicates the sequence index when an AHB command error is detected. This field will be cleared when INTR[AHBCMDERR] is write-1-clear(w1c)." line.long 0x18 "STS2,Status Register 2" hexmask.long.byte 0x18 24.--29. 1. "BREFSEL,Flash B sample clock reference delay line delay cell number selection." newline hexmask.long.byte 0x18 18.--23. 1. "BSLVSEL,Flash B sample clock slave delay line delay cell number selection." newline bitfld.long 0x18 17. "BREFLOCK,Flash B sample clock reference delay line locked." "0,1" newline bitfld.long 0x18 16. "BSLVLOCK,Flash B sample clock slave delay line locked." "0,1" newline hexmask.long.byte 0x18 8.--13. 1. "AREFSEL,Flash A sample clock reference delay line delay cell number selection." newline hexmask.long.byte 0x18 2.--7. 1. "ASLVSEL,Flash A sample clock slave delay line delay cell number selection ." newline bitfld.long 0x18 1. "AREFLOCK,Flash A sample clock reference delay line locked." "0,1" newline bitfld.long 0x18 0. "ASLVLOCK,Flash A sample clock slave delay line locked." "0,1" line.long 0x1C "AHBSPNDSTS,AHB Suspend Status Register" hexmask.long.word 0x1C 16.--31. 1. "DATLFT,Left Data size for suspended command sequence (in byte)." newline bitfld.long 0x1C 1.--3. "BUFID,AHB RX BUF ID for suspended command sequence." "0,1,2,3,4,5,6,7" newline bitfld.long 0x1C 0. "ACTIVE,Indicates if an AHB read prefetch command sequence has been suspended." "0,1" line.long 0x20 "IPRXFSTS,IP RX FIFO Status Register" hexmask.long.word 0x20 16.--31. 1. "RDCNTR,Total Read Data Counter: RDCNTR * 64 Bits." newline hexmask.long.byte 0x20 0.--7. 1. "FILL,Fill level of IP RX FIFO." line.long 0x24 "IPTXFSTS,IP TX FIFO Status Register" hexmask.long.word 0x24 16.--31. 1. "WRCNTR,Total Write Data Counter: WRCNTR * 64 Bits." newline hexmask.long.byte 0x24 0.--7. 1. "FILL,Fill level of IP TX FIFO." repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x100)++0x3 line.long 0x0 "RFDR[$1],IP RX FIFO Data Register x" hexmask.long 0x0 0.--31. 1. "RXDATA,RX Data" repeat.end repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) wgroup.long ($2+0x180)++0x3 line.long 0x0 "TFDR[$1],IP TX FIFO Data Register x" hexmask.long 0x0 0.--31. 1. "TXDATA,TX Data" repeat.end repeat 64. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "LUT[$1],LUT x" hexmask.long.byte 0x0 26.--31. 1. "OPCODE1,OPCODE1" newline bitfld.long 0x0 24.--25. "NUM_PADS1,NUM_PADS1" "0,1,2,3" newline hexmask.long.byte 0x0 16.--23. 1. "OPERAND1,OPERAND1" newline hexmask.long.byte 0x0 10.--15. 1. "OPCODE0,OPCODE" newline bitfld.long 0x0 8.--9. "NUM_PADS0,NUM_PADS0" "0,1,2,3" newline hexmask.long.byte 0x0 0.--7. 1. "OPERAND0,OPERAND0" repeat.end group.long 0x400++0x2B line.long 0x0 "HMSTR0CR,AHB Master ID 0 Control Register" hexmask.long.word 0x0 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x0 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x4 "HMSTR1CR,AHB Master ID 1 Control Register" hexmask.long.word 0x4 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x4 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x8 "HMSTR2CR,AHB Master ID 2 Control Register" hexmask.long.word 0x8 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x8 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0xC "HMSTR3CR,AHB Master ID 3 Control Register" hexmask.long.word 0xC 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0xC 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x10 "HMSTR4CR,AHB Master ID 4 Control Register" hexmask.long.word 0x10 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x10 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x14 "HMSTR5CR,AHB Master ID 5 Control Register" hexmask.long.word 0x14 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x14 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x18 "HMSTR6CR,AHB Master ID 6 Control Register" hexmask.long.word 0x18 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x18 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x1C "HMSTR7CR,AHB Master ID 7 Control Register" hexmask.long.word 0x1C 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x1C 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x20 "HADDRSTART,HADDR REMAP START ADDR" hexmask.long.tbyte 0x20 12.--31. 1. "ADDRSTART,HADDR remap range's start addr 4K aligned When ADDRSTART setting is same as ASFM_BASE and OTFAD keyblob function is enabled keyblob will also be remapped" newline bitfld.long 0x20 1. "KBINECC,OTFAD Keyblob is in ECC region and need to be remapped" "0: If key blob is in remap region FlexSPI will..,1: If key blob is in remap region FlexSPI will.." newline bitfld.long 0x20 0. "REMAPEN,AHB Bus address remap function enable" "0: HADDR REMAP Disabled,1: HADDR REMAP Enabled" line.long 0x24 "HADDREND,HADDR REMAP END ADDR" hexmask.long.tbyte 0x24 12.--31. 1. "ENDSTART,HADDR remap range's end addr 4K aligned" line.long 0x28 "HADDROFFSET,HADDR REMAP OFFSET" hexmask.long.tbyte 0x28 12.--31. 1. "ADDROFFSET,HADDR offset field remapped address will be ADDR[31:12]=ADDR_original[31:12]+ADDROFFSET" group.long 0x430++0x2F line.long 0x0 "IPSNSZSTART0,IPS nonsecure region Start address of region 0" hexmask.long.tbyte 0x0 12.--31. 1. "start_address,Start address of region 0. Minimal 4K Bytes aligned. It is flash address." line.long 0x4 "IPSNSZEND0,IPS nonsecure region End address of region 0" hexmask.long.tbyte 0x4 12.--31. 1. "end_address,End address of region 0. Minimal 4K Bytes aligned. It is flash address." line.long 0x8 "IPSNSZSTART1,IPS nonsecure region Start address of region 1" hexmask.long.tbyte 0x8 12.--31. 1. "start_address,Start address of region 1. Minimal 4K Bytes aligned. It is flash address." line.long 0xC "IPSNSZEND1,IPS nonsecure region End address of region 1" hexmask.long.tbyte 0xC 12.--31. 1. "end_address,End address of region 1. Minimal 4K Bytes aligned. It is flash address." line.long 0x10 "AHBBUFREGIONSTART0,RX BUF Start address of region 0" hexmask.long.tbyte 0x10 12.--31. 1. "start_address,Start address of region 0. Minimal 4K Bytes aligned. It is system address." line.long 0x14 "AHBBUFREGIONEND0,RX BUF region End address of region 0" hexmask.long.tbyte 0x14 12.--31. 1. "end_address,End address of region 0. Minimal 4K Bytes aligned. It is system address." line.long 0x18 "AHBBUFREGIONSTART1,RX BUF Start address of region 1" hexmask.long.tbyte 0x18 12.--31. 1. "start_address,Start address of region 1. Minimal 4K Bytes aligned. It is system address." line.long 0x1C "AHBBUFREGIONEND1,RX BUF region End address of region 1" hexmask.long.tbyte 0x1C 12.--31. 1. "end_address,End address of region 1. Minimal 4K Bytes aligned. It is system address." line.long 0x20 "AHBBUFREGIONSTART2,RX BUF Start address of region 2" hexmask.long.tbyte 0x20 12.--31. 1. "start_address,Start address of region 2. Minimal 4K Bytes aligned. It is system address." line.long 0x24 "AHBBUFREGIONEND2,RX BUF region End address of region 2" hexmask.long.tbyte 0x24 12.--31. 1. "end_address,End address of region 2. Minimal 4K Bytes aligned. It is system address." line.long 0x28 "AHBBUFREGIONSTART3,RX BUF Start address of region 3" hexmask.long.tbyte 0x28 12.--31. 1. "start_address,Start address of region 3. Minimal 4K Bytes aligned. It is system address." line.long 0x2C "AHBBUFREGIONEND3,RX BUF region End address of region 3" hexmask.long.tbyte 0x2C 12.--31. 1. "end_address,End address of region 3. Minimal 4K Bytes aligned. It is system address." tree.end tree "FLEXSPI2" base ad:0x400D0000 group.long 0x0++0x3F line.long 0x0 "MCR0,Module Control Register 0" hexmask.long.byte 0x0 24.--31. 1. "AHBGRANTWAIT,Timeout wait cycle for AHB command grant." newline hexmask.long.byte 0x0 16.--23. 1. "IPGRANTWAIT,Time out wait cycle for IP command grant." newline bitfld.long 0x0 14. "SCKFREERUNEN,This bit is used to force SCLK output free-running. For FPGA applications external device may use SCLK as reference clock to its internal PLL. If SCLK free-running is enabled data sampling with loopback clock from SCLK pad is not supported.." "0: Disable.,1: Enable." newline bitfld.long 0x0 13. "COMBINATIONEN,This bit is to support Flash Octal mode access by combining Port A and B Data pins (A_DATA[3:0] and B_DATA[3:0]) when Port A and Port B are of 4 bit data width." "0: Disable.,1: Enable." newline bitfld.long 0x0 12. "DOZEEN,Doze mode enable bit" "0: Doze mode support disabled. AHB clock and serial..,1: Doze mode support enabled. AHB clock and serial.." newline bitfld.long 0x0 11. "HSEN,Half Speed Serial Flash access Enable." "0: Disable divide by 2 of serial flash clock for..,1: Enable divide by 2 of serial flash clock for.." newline bitfld.long 0x0 8.--10. "SERCLKDIV,The serial root clock could be divided inside FlexSPI . Refer Clocks chapter for more details on clocking." "0: Divided by 1,1: Divided by 2,2: Divided by 3,3: Divided by 4,4: Divided by 5,5: Divided by 6,6: Divided by 7,7: Divided by 8" newline bitfld.long 0x0 7. "ATDFEN,Enable AHB bus Write Access to IP TX FIFO." "0: IP TX FIFO should be written by IP Bus. AHB Bus..,1: IP TX FIFO should be written by AHB Bus. IP Bus.." newline bitfld.long 0x0 6. "ARDFEN,Enable AHB bus Read Access to IP RX FIFO." "0: IP RX FIFO should be read by IP Bus. AHB Bus..,1: IP RX FIFO should be read by AHB Bus. IP Bus.." newline bitfld.long 0x0 4.--5. "RXCLKSRC,Sample Clock source selection for Flash Reading" "0: Dummy Read strobe generated by FlexSPI..,1: Dummy Read strobe generated by FlexSPI..,?,3: Flash provided Read strobe and input from DQS pad" newline bitfld.long 0x0 1. "MDIS,Module Disable" "0,1" newline bitfld.long 0x0 0. "SWRESET,Software Reset" "0,1" line.long 0x4 "MCR1,Module Control Register 1" hexmask.long.word 0x4 16.--31. 1. "SEQWAIT,Command Sequence Execution will timeout and abort after SEQWAIT * 1024 Serial Root Clock cycles" newline hexmask.long.word 0x4 0.--15. 1. "AHBBUSWAIT,AHB Read/Write access to Serial Flash Memory space will timeout if not data received from Flash or data not transmitted after AHBBUSWAIT * 1024 ahb clock cycles AHB Bus will get an error response" line.long 0x8 "MCR2,Module Control Register 2" hexmask.long.byte 0x8 24.--31. 1. "RESUMEWAIT,Wait cycle (in AHB clock cycle) for idle state before suspended command sequence resumed." newline bitfld.long 0x8 19. "SCKBDIFFOPT,B_SCLK pad can be used as A_SCLK differential clock output (inverted clock to A_SCLK). In this case port B flash access is not available. After changing the value of this field MCR0[SWRESET] should be set." "0: B_SCLK pad is used as port B SCLK clock output.,1: B_SCLK pad is used as port A SCLK inverted clock.." newline bitfld.long 0x8 15. "SAMEDEVICEEN,All external devices are same devices (both in types and size) for A1/A2/B1/B2." "0: In Individual mode..,1: FLSHA1CR0/FLSHA1CR1/FLSHA1CR2 register settings.." newline bitfld.long 0x8 11. "CLRAHBBUFOPT,This bit determines whether AHB RX Buffer and AHB TX Buffer will be cleaned automatically when FlexSPI returns STOP mode ACK. Software should set this bit if AHB RX Buffer or AHB TX Buffer will be powered off in STOP mode. Otherwise AHB read.." "0: AHB RX/TX Buffer will not be cleaned..,1: AHB RX/TX Buffer will be cleaned automatically.." line.long 0xC "AHBCR,AHB Bus Control Register" bitfld.long 0xC 20.--21. "ALIGNMENT,Decides all AHB read/write boundary. All access cross the boundary will be divided into smaller sub accesses." "0: No limit,1: 1 KBytes,2: 512 Bytes,3: 256 Bytes" newline bitfld.long 0xC 19. "ECCSWAPEN,ECC Read data swap function" "0: rdata send to ecc check without swap.,1: rdata send to ecc ehck with swap." newline bitfld.long 0xC 18. "HMSTRIDREMAP,AHB Master ID Remapping enable" "0,1" newline bitfld.long 0xC 17. "ECCMULTIERRCLR,AHB ECC Multi bits ERR CLR" "0,1" newline bitfld.long 0xC 16. "ECCSINGLEERRCLR,AHB ECC Single bit ERR CLR" "0,1" newline bitfld.long 0xC 15. "KEYECCEN,OTFAD KEY BLOC ECC Enable" "0: AHB KEY ECC check disabled,1: AHB KEY ECC check enabled" newline bitfld.long 0xC 13.--14. "SPLIT_LIMIT,AHB SPLIT SIZE" "0: AHB Split Size=8bytes,1: AHB Split Size=16bytes,2: AHB Split Size=32bytes,3: AHB Split Size=64bytes" newline bitfld.long 0xC 12. "SPLITEN,AHB transaction SPLIT" "0: AHB Split disabled,1: AHB Split enabled" newline bitfld.long 0xC 11. "ECCEN,AHB Read ECC Enable" "0: AHB read ECC check disabled,1: AHB read ECC check enabled" newline bitfld.long 0xC 10. "READSZALIGN,AHB Read Size Alignment" "0: AHB read size will be decided by other register..,1: AHB read size to up size to 8 bytes aligned no.." newline bitfld.long 0xC 6. "READADDROPT,AHB Read Address option bit. This option bit is intend to remove AHB burst start address alignment limitation." "0: There is AHB read burst start address alignment..,1: There is no AHB read burst start address.." newline bitfld.long 0xC 5. "PREFETCHEN,AHB Read Prefetch Enable." "0,1" newline bitfld.long 0xC 4. "BUFFERABLEEN,Enable AHB bus bufferable write access support. This field affects the last beat of AHB write access refer for more details about AHB bufferable write." "0: Disabled. For all AHB write access (no matter..,1: Enabled. For AHB bufferable write access FlexSPI.." newline bitfld.long 0xC 3. "CACHABLEEN,Enable AHB bus cachable read access support." "0: Disabled. When there is AHB bus cachable read..,1: Enabled. When there is AHB bus cachable read.." newline bitfld.long 0xC 1. "CLRAHBRXBUF,Clear the status/pointers of AHB RX Buffer. Auto-cleared." "0,1" newline bitfld.long 0xC 0. "APAREN,Parallel mode enabled for AHB triggered Command (both read and write) ." "0: Flash will be accessed in Individual mode.,1: Flash will be accessed in Parallel mode." line.long 0x10 "INTEN,Interrupt Enable Register" bitfld.long 0x10 16. "IPCMDSECUREVIOEN,IP command security violation interrupt enable." "0,1" newline bitfld.long 0x10 15. "ECCSINGLEERREN,ECC single bit error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 14. "ECCMULTIERREN,ECC multi bits error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 13. "KEYERROREN,OTFAD key blob processing error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 12. "KEYDONEEN,OTFAD key blob processing done interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 11. "SEQTIMEOUTEN,Sequence execution timeout interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 10. "AHBBUSERROREN,AHB Bus error interrupt enable.Refer Interrupts chapter for more details." "0,1" newline bitfld.long 0x10 9. "SCKSTOPBYWREN,SCLK is stopped during command sequence because Async TX FIFO empty interrupt enable." "0,1" newline bitfld.long 0x10 8. "SCKSTOPBYRDEN,SCLK is stopped during command sequence because Async RX FIFO full interrupt enable." "0,1" newline bitfld.long 0x10 6. "IPTXWEEN,IP TX FIFO WaterMark empty interrupt enable." "0,1" newline bitfld.long 0x10 5. "IPRXWAEN,IP RX FIFO WaterMark available interrupt enable." "0,1" newline bitfld.long 0x10 4. "AHBCMDERREN,AHB triggered Command Sequences Error Detected interrupt enable." "0,1" newline bitfld.long 0x10 3. "IPCMDERREN,IP triggered Command Sequences Error Detected interrupt enable." "0,1" newline bitfld.long 0x10 2. "AHBCMDGEEN,AHB triggered Command Sequences Grant Timeout interrupt enable." "0,1" newline bitfld.long 0x10 1. "IPCMDGEEN,IP triggered Command Sequences Grant Timeout interrupt enable." "0,1" newline bitfld.long 0x10 0. "IPCMDDONEEN,IP triggered Command Sequences Execution finished interrupt enable." "0,1" line.long 0x14 "INTR,Interrupt Register" eventfld.long 0x14 16. "IPCMDSECUREVIO,IP command security violation interrupt." "0,1" newline eventfld.long 0x14 15. "ECCSINGLEERR,ECC single bit error interrupt." "0,1" newline eventfld.long 0x14 14. "ECCMULTIERR,ECC multi bits error interrupt." "0,1" newline rbitfld.long 0x14 13. "KEYERROR,OTFAD key blob processing error interrupt." "0,1" newline eventfld.long 0x14 12. "KEYDONE,OTFAD key blob processing done interrupt." "0,1" newline eventfld.long 0x14 11. "SEQTIMEOUT,Sequence execution timeout interrupt." "0,1" newline eventfld.long 0x14 10. "AHBBUSERROR,AHB Bus timeout or AHB bus illegal access Flash during OTFAD key blob processing interrupt." "0,1" newline eventfld.long 0x14 9. "SCKSTOPBYWR,SCLK is stopped during command sequence because Async TX FIFO empty interrupt." "0,1" newline eventfld.long 0x14 8. "SCKSTOPBYRD,SCLK is stopped during command sequence because Async RX FIFO full interrupt." "0,1" newline eventfld.long 0x14 6. "IPTXWE,IP TX FIFO watermark empty interrupt." "0,1" newline eventfld.long 0x14 5. "IPRXWA,IP RX FIFO watermark available interrupt." "0,1" newline eventfld.long 0x14 4. "AHBCMDERR,AHB triggered Command Sequences Error Detected interrupt. When an error detected for AHB command this command will be ignored and not executed at all." "0,1" newline eventfld.long 0x14 3. "IPCMDERR,IP triggered Command Sequences Error Detected interrupt. When an error detected for IP command this command will be ignored and not executed at all." "0,1" newline eventfld.long 0x14 2. "AHBCMDGE,AHB triggered Command Sequences Grant Timeout interrupt." "0,1" newline eventfld.long 0x14 1. "IPCMDGE,IP triggered Command Sequences Grant Timeout interrupt." "0,1" newline eventfld.long 0x14 0. "IPCMDDONE,IP triggered Command Sequences Execution finished interrupt. This interrupt is also generated when there is IPCMDGE or IPCMDERR interrupt generated." "0,1" line.long 0x18 "LUTKEY,LUT Key Register" hexmask.long 0x18 0.--31. 1. "KEY,The Key to lock or unlock LUT." line.long 0x1C "LUTCR,LUT Control Register" bitfld.long 0x1C 2. "PROTECT,LUT protection" "0,1" newline bitfld.long 0x1C 1. "UNLOCK,Unlock LUT" "0,1" newline bitfld.long 0x1C 0. "LOCK,Lock LUT" "0,1" line.long 0x20 "AHBRXBUF0CR0,AHB RX Buffer 0 Control Register 0" bitfld.long 0x20 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x20 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x20 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x20 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x20 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x24 "AHBRXBUF1CR0,AHB RX Buffer 1 Control Register 0" bitfld.long 0x24 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x24 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x24 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x24 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x24 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x28 "AHBRXBUF2CR0,AHB RX Buffer 2 Control Register 0" bitfld.long 0x28 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x28 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x28 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x28 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x28 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x2C "AHBRXBUF3CR0,AHB RX Buffer 3 Control Register 0" bitfld.long 0x2C 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x2C 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x2C 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x2C 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x2C 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x30 "AHBRXBUF4CR0,AHB RX Buffer 4 Control Register 0" bitfld.long 0x30 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x30 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x30 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x30 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x30 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x34 "AHBRXBUF5CR0,AHB RX Buffer 5 Control Register 0" bitfld.long 0x34 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x34 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x34 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x34 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x34 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x38 "AHBRXBUF6CR0,AHB RX Buffer 6 Control Register 0" bitfld.long 0x38 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x38 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x38 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x38 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x38 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." line.long 0x3C "AHBRXBUF7CR0,AHB RX Buffer 7 Control Register 0" bitfld.long 0x3C 31. "PREFETCHEN,AHB Read Prefetch Enable for current AHB RX Buffer corresponding Master." "0,1" newline bitfld.long 0x3C 30. "REGIONEN,AHB RX Buffer address region funciton enable" "0,1" newline bitfld.long 0x3C 24.--26. "PRIORITY,This priority for AHB Master Read which this AHB RX Buffer is assigned. 7 is the highest priority 0 the lowest." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x3C 16.--19. 1. "MSTRID,This AHB RX Buffer is assigned according to AHB Master with ID (MSTR_ID)." newline hexmask.long.word 0x3C 0.--9. 1. "BUFSZ,AHB RX Buffer Size in 64 bits." group.long 0x60++0xF line.long 0x0 "FLSHA1CR0,Flash Control Register 0" bitfld.long 0x0 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x0 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x0 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0x4 "FLSHA2CR0,Flash Control Register 0" bitfld.long 0x4 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x4 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x4 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0x8 "FLSHB1CR0,Flash Control Register 0" bitfld.long 0x8 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0x8 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0x8 0.--22. 1. "FLSHSZ,Flash Size in KByte." line.long 0xC "FLSHB2CR0,Flash Control Register 0" bitfld.long 0xC 31. "SPLITRDEN,AHB read access split function control." "0,1" newline bitfld.long 0xC 30. "SPLITWREN,AHB write access split function control." "0,1" newline hexmask.long.tbyte 0xC 0.--22. 1. "FLSHSZ,Flash Size in KByte." repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x70)++0x3 line.long 0x0 "FLSHCR1$1,Flash Control Register 1" hexmask.long.word 0x0 16.--31. 1. "CSINTERVAL,This field is used to set the minimum interval between flash device Chip selection deassertion and flash device Chip selection assertion. If external flash has a limitation on the interval between command sequences this field should be set.." newline bitfld.long 0x0 15. "CSINTERVALUNIT,CS interval unit" "0: The CS interval unit is 1 serial clock cycle,1: The CS interval unit is 256 serial clock cycle" newline hexmask.long.byte 0x0 11.--14. 1. "CAS,Column Address Size." newline bitfld.long 0x0 10. "WA,Word Addressable." "0,1" newline hexmask.long.byte 0x0 5.--9. 1. "TCSH,Serial Flash CS Hold time." newline hexmask.long.byte 0x0 0.--4. 1. "TCSS,Serial Flash CS setup time." repeat.end repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x80)++0x3 line.long 0x0 "FLSHCR2$1,Flash Control Register 2" bitfld.long 0x0 31. "CLRINSTRPTR,Clear the instruction pointer which is internally saved pointer by JMP_ON_CS. Refer Programmable Sequence Engine for details." "0,1" newline bitfld.long 0x0 28.--30. "AWRWAITUNIT,AWRWAIT unit" "0: The AWRWAIT unit is 2 ahb clock cycle,1: The AWRWAIT unit is 8 ahb clock cycle,2: The AWRWAIT unit is 32 ahb clock cycle,3: The AWRWAIT unit is 128 ahb clock cycle,4: The AWRWAIT unit is 512 ahb clock cycle,5: The AWRWAIT unit is 2048 ahb clock cycle,6: The AWRWAIT unit is 8192 ahb clock cycle,7: The AWRWAIT unit is 32768 ahb clock cycle" newline hexmask.long.word 0x0 16.--27. 1. "AWRWAIT,For certain devices (such as FPGA) it need some time to write data into internal memory after the command sequences finished on FlexSPI interface" newline bitfld.long 0x0 13.--15. "AWRSEQNUM,Sequence Number for AHB Write triggered Command." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 8.--11. 1. "AWRSEQID,Sequence Index for AHB Write triggered Command." newline bitfld.long 0x0 5.--7. "ARDSEQNUM,Sequence Number for AHB Read triggered Command in LUT." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 0.--3. 1. "ARDSEQID,Sequence Index for AHB Read triggered Command in LUT." repeat.end group.long 0x94++0x3 line.long 0x0 "FLSHCR4,Flash Control Register 4" bitfld.long 0x0 11. "PAR_ADDR_ADJ_DIS,Disable the address shift logic for lower density of 16 bit PSRAM." "0,1" newline bitfld.long 0x0 9.--10. "PAR_WM,Enable APMEM 16 bit write mask function bit 9 for A1-B1 pair bit 10 for A2-B2 pair." "?,1: B1 pair,2: B2 pair,?" newline bitfld.long 0x0 3. "WMENB,Write mask enable bit for flash device on port B. When write mask function is needed for memory device on port B this bit must be set." "0: Write mask is disabled DQS(RWDS) pin will be..,1: Write mask is enabled DQS(RWDS) pin will be.." newline bitfld.long 0x0 2. "WMENA,Write mask enable bit for flash device on port A. When write mask function is needed for memory device on port A this bit must be set." "0: Write mask is disabled DQS(RWDS) pin will be..,1: Write mask is enabled DQS(RWDS) pin will be.." newline bitfld.long 0x0 1. "WMOPT2,Write mask option bit 2. When using AP memory This option bit could be used to remove AHB write burst minimal length limitation. When using this bit WMOPT1 should also be set." "0: DQS pin will be used as Write Mask when writing..,1: DQS pin will not be used as Write Mask when.." newline bitfld.long 0x0 0. "WMOPT1,Write mask option bit 1. This option bit could be used to remove AHB write burst start address alignment limitation." "0: DQS pin will be used as Write Mask when writing..,1: DQS pin will not be used as Write Mask when.." group.long 0xA0++0x7 line.long 0x0 "IPCR0,IP Control Register 0" hexmask.long 0x0 0.--31. 1. "SFAR,Serial Flash Address for IP command." line.long 0x4 "IPCR1,IP Control Register 1" bitfld.long 0x4 31. "IPAREN,Parallel mode Enabled for IP command." "0: Flash will be accessed in Individual mode.,1: Flash will be accessed in Parallel mode." newline bitfld.long 0x4 24.--26. "ISEQNUM,Sequence Number for IP command: ISEQNUM+1." "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x4 16.--19. 1. "ISEQID,Sequence Index in LUT for IP command." newline hexmask.long.word 0x4 0.--15. 1. "IDATSZ,Flash Read/Program Data Size (in Bytes) for IP command." group.long 0xB0++0x3 line.long 0x0 "IPCMD,IP Command Register" bitfld.long 0x0 0. "TRG,Setting this bit will trigger an IP Command." "0,1" group.long 0xB8++0x7 line.long 0x0 "IPRXFCR,IP RX FIFO Control Register" hexmask.long.byte 0x0 2.--6. 1. "RXWMRK,Watermark level is (RXWMRK+1)*64 Bits." newline bitfld.long 0x0 1. "RXDMAEN,IP RX FIFO reading by DMA enabled." "0: IP RX FIFO would be read by processor.,1: IP RX FIFO would be read by DMA." newline bitfld.long 0x0 0. "CLRIPRXF,Clear all valid data entries in IP RX FIFO." "0,1" line.long 0x4 "IPTXFCR,IP TX FIFO Control Register" hexmask.long.byte 0x4 2.--6. 1. "TXWMRK,Watermark level is (TXWMRK+1)*64 Bits." newline bitfld.long 0x4 1. "TXDMAEN,IP TX FIFO filling by DMA enabled." "0: IP TX FIFO would be filled by processor.,1: IP TX FIFO would be filled by DMA." newline bitfld.long 0x4 0. "CLRIPTXF,Clear all valid data entries in IP TX FIFO." "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xC0)++0x3 line.long 0x0 "DLLCR$1,DLL Control Register 0" hexmask.long.byte 0x0 9.--14. 1. "OVRDVAL,Slave clock delay line delay cell number selection override value." newline bitfld.long 0x0 8. "OVRDEN,Slave clock delay line delay cell number selection override enable." "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "SLVDLYTARGET,The delay target for slave delay line is: ((SLVDLYTARGET+1) * 1/32 * clock cycle of reference clock (serial root clock). If serial root clock is >= 100 MHz DLLEN set to 0x1 OVRDEN set to =0x0 then SLVDLYTARGET setting of 0xF is recommended." newline bitfld.long 0x0 1. "DLLRESET,Software could force a reset on DLL by setting this field to 0x1. This will cause the DLL to lose lock and re-calibrate to detect an ref_clock half period phase shift. The reset action is edge triggered so software need to clear this bit after.." "0,1" newline bitfld.long 0x0 0. "DLLEN,DLL calibration enable." "0,1" repeat.end rgroup.long 0xD0++0x27 line.long 0x0 "MISCCR4,Misc Control Register 4" hexmask.long 0x0 0.--31. 1. "AHBADDRESS,AHB bus address that trigger the current ECC multi bits error interrupt." line.long 0x4 "MISCCR5,Misc Control Register 5" hexmask.long 0x4 0.--31. 1. "ECCSINGLEERRORCORR,ECC single bit error correction indication." line.long 0x8 "MISCCR6,Misc Control Register 6" hexmask.long 0x8 2.--31. 1. "ADDRESS,ECC single error address" newline bitfld.long 0x8 1. "HIT,ECC single error information Hit" "0,1" newline bitfld.long 0x8 0. "VALID,ECC single error information Valid" "0,1" line.long 0xC "MISCCR7,Misc Control Register 7" hexmask.long 0xC 2.--31. 1. "ADDRESS,ECC multi error address" newline bitfld.long 0xC 1. "HIT,ECC multi error information Hit" "0,1" newline bitfld.long 0xC 0. "VALID,ECC multi error information Valid" "0,1" line.long 0x10 "STS0,Status Register 0" bitfld.long 0x10 2.--3. "ARBCMDSRC,This status field indicates the trigger source of current command sequence granted by arbitrator. This field value is meaningless when ARB_CTL is not busy (STS0[ARBIDLE]=0x1)." "0: Triggered by AHB read command (triggered by AHB..,1: Triggered by AHB write command (triggered by AHB..,2: Triggered by IP command (triggered by setting..,3: Triggered by suspended command (resumed)." newline bitfld.long 0x10 1. "ARBIDLE,This status bit indicates the state machine in ARB_CTL is busy and there is command sequence granted by arbitrator and not finished yet on FlexSPI interface. When ARB_CTL state (ARBIDLE=0x1) is idle there will be no transaction on FlexSPI.." "0,1" newline bitfld.long 0x10 0. "SEQIDLE,This status bit indicates the state machine in SEQ_CTL is idle and there is command sequence executing on FlexSPI interface." "0,1" line.long 0x14 "STS1,Status Register 1" hexmask.long.byte 0x14 24.--27. 1. "IPCMDERRCODE,Indicates the Error Code when IP command Error detected. This field will be cleared when INTR[IPCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 16.--19. 1. "IPCMDERRID,Indicates the sequence Index when IP command error detected. This field will be cleared when INTR[IPCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 8.--11. 1. "AHBCMDERRCODE,Indicates the Error Code when AHB command Error detected. This field will be cleared when INTR[AHBCMDERR] is write-1-clear(w1c)." newline hexmask.long.byte 0x14 0.--3. 1. "AHBCMDERRID,Indicates the sequence index when an AHB command error is detected. This field will be cleared when INTR[AHBCMDERR] is write-1-clear(w1c)." line.long 0x18 "STS2,Status Register 2" hexmask.long.byte 0x18 24.--29. 1. "BREFSEL,Flash B sample clock reference delay line delay cell number selection." newline hexmask.long.byte 0x18 18.--23. 1. "BSLVSEL,Flash B sample clock slave delay line delay cell number selection." newline bitfld.long 0x18 17. "BREFLOCK,Flash B sample clock reference delay line locked." "0,1" newline bitfld.long 0x18 16. "BSLVLOCK,Flash B sample clock slave delay line locked." "0,1" newline hexmask.long.byte 0x18 8.--13. 1. "AREFSEL,Flash A sample clock reference delay line delay cell number selection." newline hexmask.long.byte 0x18 2.--7. 1. "ASLVSEL,Flash A sample clock slave delay line delay cell number selection ." newline bitfld.long 0x18 1. "AREFLOCK,Flash A sample clock reference delay line locked." "0,1" newline bitfld.long 0x18 0. "ASLVLOCK,Flash A sample clock slave delay line locked." "0,1" line.long 0x1C "AHBSPNDSTS,AHB Suspend Status Register" hexmask.long.word 0x1C 16.--31. 1. "DATLFT,Left Data size for suspended command sequence (in byte)." newline bitfld.long 0x1C 1.--3. "BUFID,AHB RX BUF ID for suspended command sequence." "0,1,2,3,4,5,6,7" newline bitfld.long 0x1C 0. "ACTIVE,Indicates if an AHB read prefetch command sequence has been suspended." "0,1" line.long 0x20 "IPRXFSTS,IP RX FIFO Status Register" hexmask.long.word 0x20 16.--31. 1. "RDCNTR,Total Read Data Counter: RDCNTR * 64 Bits." newline hexmask.long.byte 0x20 0.--7. 1. "FILL,Fill level of IP RX FIFO." line.long 0x24 "IPTXFSTS,IP TX FIFO Status Register" hexmask.long.word 0x24 16.--31. 1. "WRCNTR,Total Write Data Counter: WRCNTR * 64 Bits." newline hexmask.long.byte 0x24 0.--7. 1. "FILL,Fill level of IP TX FIFO." repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x100)++0x3 line.long 0x0 "RFDR[$1],IP RX FIFO Data Register x" hexmask.long 0x0 0.--31. 1. "RXDATA,RX Data" repeat.end repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) wgroup.long ($2+0x180)++0x3 line.long 0x0 "TFDR[$1],IP TX FIFO Data Register x" hexmask.long 0x0 0.--31. 1. "TXDATA,TX Data" repeat.end repeat 64. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "LUT[$1],LUT x" hexmask.long.byte 0x0 26.--31. 1. "OPCODE1,OPCODE1" newline bitfld.long 0x0 24.--25. "NUM_PADS1,NUM_PADS1" "0,1,2,3" newline hexmask.long.byte 0x0 16.--23. 1. "OPERAND1,OPERAND1" newline hexmask.long.byte 0x0 10.--15. 1. "OPCODE0,OPCODE" newline bitfld.long 0x0 8.--9. "NUM_PADS0,NUM_PADS0" "0,1,2,3" newline hexmask.long.byte 0x0 0.--7. 1. "OPERAND0,OPERAND0" repeat.end group.long 0x400++0x2B line.long 0x0 "HMSTR0CR,AHB Master ID 0 Control Register" hexmask.long.word 0x0 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x0 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x4 "HMSTR1CR,AHB Master ID 1 Control Register" hexmask.long.word 0x4 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x4 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x8 "HMSTR2CR,AHB Master ID 2 Control Register" hexmask.long.word 0x8 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x8 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0xC "HMSTR3CR,AHB Master ID 3 Control Register" hexmask.long.word 0xC 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0xC 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x10 "HMSTR4CR,AHB Master ID 4 Control Register" hexmask.long.word 0x10 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x10 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x14 "HMSTR5CR,AHB Master ID 5 Control Register" hexmask.long.word 0x14 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x14 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x18 "HMSTR6CR,AHB Master ID 6 Control Register" hexmask.long.word 0x18 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x18 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x1C "HMSTR7CR,AHB Master ID 7 Control Register" hexmask.long.word 0x1C 16.--31. 1. "MSTRID,This is expected Master ID." newline hexmask.long.word 0x1C 0.--15. 1. "MASK,Mask bits for AHB master ID." line.long 0x20 "HADDRSTART,HADDR REMAP START ADDR" hexmask.long.tbyte 0x20 12.--31. 1. "ADDRSTART,HADDR remap range's start addr 4K aligned When ADDRSTART setting is same as ASFM_BASE and OTFAD keyblob function is enabled keyblob will also be remapped" newline bitfld.long 0x20 1. "KBINECC,OTFAD Keyblob is in ECC region and need to be remapped" "0: If key blob is in remap region FlexSPI will..,1: If key blob is in remap region FlexSPI will.." newline bitfld.long 0x20 0. "REMAPEN,AHB Bus address remap function enable" "0: HADDR REMAP Disabled,1: HADDR REMAP Enabled" line.long 0x24 "HADDREND,HADDR REMAP END ADDR" hexmask.long.tbyte 0x24 12.--31. 1. "ENDSTART,HADDR remap range's end addr 4K aligned" line.long 0x28 "HADDROFFSET,HADDR REMAP OFFSET" hexmask.long.tbyte 0x28 12.--31. 1. "ADDROFFSET,HADDR offset field remapped address will be ADDR[31:12]=ADDR_original[31:12]+ADDROFFSET" group.long 0x430++0x2F line.long 0x0 "IPSNSZSTART0,IPS nonsecure region Start address of region 0" hexmask.long.tbyte 0x0 12.--31. 1. "start_address,Start address of region 0. Minimal 4K Bytes aligned. It is flash address." line.long 0x4 "IPSNSZEND0,IPS nonsecure region End address of region 0" hexmask.long.tbyte 0x4 12.--31. 1. "end_address,End address of region 0. Minimal 4K Bytes aligned. It is flash address." line.long 0x8 "IPSNSZSTART1,IPS nonsecure region Start address of region 1" hexmask.long.tbyte 0x8 12.--31. 1. "start_address,Start address of region 1. Minimal 4K Bytes aligned. It is flash address." line.long 0xC "IPSNSZEND1,IPS nonsecure region End address of region 1" hexmask.long.tbyte 0xC 12.--31. 1. "end_address,End address of region 1. Minimal 4K Bytes aligned. It is flash address." line.long 0x10 "AHBBUFREGIONSTART0,RX BUF Start address of region 0" hexmask.long.tbyte 0x10 12.--31. 1. "start_address,Start address of region 0. Minimal 4K Bytes aligned. It is system address." line.long 0x14 "AHBBUFREGIONEND0,RX BUF region End address of region 0" hexmask.long.tbyte 0x14 12.--31. 1. "end_address,End address of region 0. Minimal 4K Bytes aligned. It is system address." line.long 0x18 "AHBBUFREGIONSTART1,RX BUF Start address of region 1" hexmask.long.tbyte 0x18 12.--31. 1. "start_address,Start address of region 1. Minimal 4K Bytes aligned. It is system address." line.long 0x1C "AHBBUFREGIONEND1,RX BUF region End address of region 1" hexmask.long.tbyte 0x1C 12.--31. 1. "end_address,End address of region 1. Minimal 4K Bytes aligned. It is system address." line.long 0x20 "AHBBUFREGIONSTART2,RX BUF Start address of region 2" hexmask.long.tbyte 0x20 12.--31. 1. "start_address,Start address of region 2. Minimal 4K Bytes aligned. It is system address." line.long 0x24 "AHBBUFREGIONEND2,RX BUF region End address of region 2" hexmask.long.tbyte 0x24 12.--31. 1. "end_address,End address of region 2. Minimal 4K Bytes aligned. It is system address." line.long 0x28 "AHBBUFREGIONSTART3,RX BUF Start address of region 3" hexmask.long.tbyte 0x28 12.--31. 1. "start_address,Start address of region 3. Minimal 4K Bytes aligned. It is system address." line.long 0x2C "AHBBUFREGIONEND3,RX BUF region End address of region 3" hexmask.long.tbyte 0x2C 12.--31. 1. "end_address,End address of region 3. Minimal 4K Bytes aligned. It is system address." tree.end tree.end tree "GPC" base ad:0x0 tree "GPC_CPU_MODE_CTRL" tree "GPC_CPU_MODE_CTRL_0" base ad:0x40C00000 group.long 0x4++0xF line.long 0x0 "CM_AUTHEN_CTRL,CM Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access CPU mode..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access CPU mode..,1: Allow both privilege and user mode to access CPU.." line.long 0x4 "CM_INT_CTRL,CM Interrupt Control" eventfld.long 0x4 18. "SP_REQ_NOT_ALLOWED_SOFT_INT,sp_req_not_allowed_for_soft interrupt status and clear register" "0,1" newline eventfld.long 0x4 17. "SP_REQ_NOT_ALLOWED_WAKEUP_INT,sp_req_not_allowed_for_wakeup interrupt status and clear register" "0,1" newline eventfld.long 0x4 16. "SP_REQ_NOT_ALLOWED_SLEEP_INT,sp_req_not_allowed_for_sleep interrupt status and clear register" "0,1" newline bitfld.long 0x4 2. "SP_REQ_NOT_ALLOWED_SOFT_INT_EN,sp_req_not_allowed_for_soft interrupt enable" "0: Interrupt disable,1: Interrupt enable" newline bitfld.long 0x4 1. "SP_REQ_NOT_ALLOWED_WAKEUP_INT_EN,sp_req_not_allowed_for_wakeup interrupt enable" "0: Interrupt disable,1: Interrupt enable" newline bitfld.long 0x4 0. "SP_REQ_NOT_ALLOWED_SLEEP_INT_EN,sp_req_not_allowed_for_sleep interrupt enable" "0: Interrupt disable,1: Interrupt enable" line.long 0x8 "CM_MISC,Miscellaneous" bitfld.long 0x8 4. "MASTER_CPU,Master CPU" "0,1" newline rbitfld.long 0x8 2. "SLEEP_HOLD_STAT,Status of cpu_sleep_hold_ack_b" "0,1" newline bitfld.long 0x8 1. "SLEEP_HOLD_EN,Allow cpu_sleep_hold_req assert during CPU low power status" "0: Disable cpu_sleep_hold_req,1: Allow cpu_sleep_hold_req assert during CPU low.." newline rbitfld.long 0x8 0. "NMI_STAT,Non-masked interrupt status" "0: NMI is not asserting,1: NMI is asserting" line.long 0xC "CM_MODE_CTRL,CPU mode control" bitfld.long 0xC 4. "WFE_EN,WFE assertion can be sleep event" "0: WFE assertion can not trigger low power,1: WFE assertion can trigger low power" newline bitfld.long 0xC 0.--1. "CPU_MODE_TARGET,The CPU mode the CPU platform should transit to on next sleep event" "0: Stay in RUN mode,1: Transit to WAIT mode,2: Transit to STOP mode,3: Transit to SUSPEND mode" rgroup.long 0x14++0x3 line.long 0x0 "CM_MODE_STAT,CM CPU mode Status" bitfld.long 0x0 2.--3. "CPU_MODE_PREVIOUS,Previous CPU mode" "0: CPU was previously in RUN mode,1: CPU was previously in WAIT mode,2: CPU was previously in STOP mode,3: CPU was previously in SUSPEND mode" newline bitfld.long 0x0 0.--1. "CPU_MODE_CURRENT,Current CPU mode" "0: CPU is currently in RUN mode,1: CPU is currently in WAIT mode,2: CPU is currently in STOP mode,3: CPU is currently in SUSPEND mode" group.long 0x100++0x1F line.long 0x0 "CM_IRQ_WAKEUP_MASK_0,CM IRQ0~31 wakeup mask" hexmask.long 0x0 0.--31. 1. "IRQ_WAKEUP_MASK_0_31,'1' means the IRQ cannot wakeup CPU platform" line.long 0x4 "CM_IRQ_WAKEUP_MASK_1,CM IRQ32~63 wakeup mask" hexmask.long 0x4 0.--31. 1. "IRQ_WAKEUP_MASK_32_63,'1' means the IRQ cannot wakeup CPU platform" line.long 0x8 "CM_IRQ_WAKEUP_MASK_2,CM IRQ64~95 wakeup mask" hexmask.long 0x8 0.--31. 1. "IRQ_WAKEUP_MASK_64_95,'1' means the IRQ cannot wakeup CPU platform" line.long 0xC "CM_IRQ_WAKEUP_MASK_3,CM IRQ96~127 wakeup mask" hexmask.long 0xC 0.--31. 1. "IRQ_WAKEUP_MASK_96_127,'1' means the IRQ cannot wakeup CPU platform" line.long 0x10 "CM_IRQ_WAKEUP_MASK_4,CM IRQ128~159 wakeup mask" hexmask.long 0x10 0.--31. 1. "IRQ_WAKEUP_MASK_128_159,'1' means the IRQ cannot wakeup CPU platform" line.long 0x14 "CM_IRQ_WAKEUP_MASK_5,CM IRQ160~191 wakeup mask" hexmask.long 0x14 0.--31. 1. "IRQ_WAKEUP_MASK_160_191,'1' means the IRQ cannot wakeup CPU platform" line.long 0x18 "CM_IRQ_WAKEUP_MASK_6,CM IRQ192~223 wakeup mask" hexmask.long 0x18 0.--31. 1. "IRQ_WAKEUP_MASK_192_223,'1' means the IRQ cannot wakeup CPU platform" line.long 0x1C "CM_IRQ_WAKEUP_MASK_7,CM IRQ224~255 wakeup mask" hexmask.long 0x1C 0.--31. 1. "IRQ_WAKEUP_MASK_224_255,'1' means the IRQ cannot wakeup CPU platform" group.long 0x140++0x3 line.long 0x0 "CM_NON_IRQ_WAKEUP_MASK,CM non-irq wakeup mask" bitfld.long 0x0 1. "DEBUG_WAKEUP_MASK,'1' means the debug_wakeup_request cannot wakeup CPU platform" "0,1" newline bitfld.long 0x0 0. "EVENT_WAKEUP_MASK,There are 256 interrupts and 1 event as a wakeup source for GPC. This field masks the 1 event wakeup source." "?,1: The event cannot wakeup CPU platform" rgroup.long 0x150++0x1F line.long 0x0 "CM_IRQ_WAKEUP_STAT_0,CM IRQ0~31 wakeup status" hexmask.long 0x0 0.--31. 1. "IRQ_WAKEUP_STAT_0_31,IRQ status" line.long 0x4 "CM_IRQ_WAKEUP_STAT_1,CM IRQ32~63 wakeup status" hexmask.long 0x4 0.--31. 1. "IRQ_WAKEUP_STAT_32_63,IRQ status" line.long 0x8 "CM_IRQ_WAKEUP_STAT_2,CM IRQ64~95 wakeup status" hexmask.long 0x8 0.--31. 1. "IRQ_WAKEUP_STAT_64_95,IRQ status" line.long 0xC "CM_IRQ_WAKEUP_STAT_3,CM IRQ96~127 wakeup status" hexmask.long 0xC 0.--31. 1. "IRQ_WAKEUP_STAT_96_127,IRQ status" line.long 0x10 "CM_IRQ_WAKEUP_STAT_4,CM IRQ128~159 wakeup status" hexmask.long 0x10 0.--31. 1. "IRQ_WAKEUP_STAT_128_159,IRQ status" line.long 0x14 "CM_IRQ_WAKEUP_STAT_5,CM IRQ160~191 wakeup status" hexmask.long 0x14 0.--31. 1. "IRQ_WAKEUP_STAT_160_191,IRQ status" line.long 0x18 "CM_IRQ_WAKEUP_STAT_6,CM IRQ192~223 wakeup status" hexmask.long 0x18 0.--31. 1. "IRQ_WAKEUP_STAT_192_223,IRQ status" line.long 0x1C "CM_IRQ_WAKEUP_STAT_7,CM IRQ224~255 wakeup status" hexmask.long 0x1C 0.--31. 1. "IRQ_WAKEUP_MASK_224_255,IRQ status" rgroup.long 0x190++0x3 line.long 0x0 "CM_NON_IRQ_WAKEUP_STAT,CM non-irq wakeup status" bitfld.long 0x0 1. "DEBUG_WAKEUP_STAT,Debug wakeup status" "0,1" newline bitfld.long 0x0 0. "EVENT_WAKEUP_STAT,Event wakeup status" "?,1: Interrupt is asserting (pending)" group.long 0x200++0x3 line.long 0x0 "CM_SLEEP_SSAR_CTRL,CM sleep SSAR control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE." group.long 0x208++0x3 line.long 0x0 "CM_SLEEP_LPCG_CTRL,CM sleep LPCG control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x210++0x3 line.long 0x0 "CM_SLEEP_PLL_CTRL,CM sleep PLL control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x218++0x3 line.long 0x0 "CM_SLEEP_ISO_CTRL,CM sleep isolation control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x220++0x3 line.long 0x0 "CM_SLEEP_RESET_CTRL,CM sleep reset control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x228++0x3 line.long 0x0 "CM_SLEEP_POWER_CTRL,CM sleep power control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x290++0x3 line.long 0x0 "CM_WAKEUP_POWER_CTRL,CM wakeup power control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x298++0x3 line.long 0x0 "CM_WAKEUP_RESET_CTRL,CM wakeup reset control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2A0++0x3 line.long 0x0 "CM_WAKEUP_ISO_CTRL,CM wakeup isolation control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2A8++0x3 line.long 0x0 "CM_WAKEUP_PLL_CTRL,CM wakeup PLL control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2B0++0x3 line.long 0x0 "CM_WAKEUP_LPCG_CTRL,CM wakeup LPCG control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2B8++0x3 line.long 0x0 "CM_WAKEUP_SSAR_CTRL,CM wakeup SSAR control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x300++0x3 line.long 0x0 "CM_SP_CTRL,CM Setpoint Control" bitfld.long 0x0 15. "CPU_SP_WAKEUP_SEL,Select the Setpoint transiton on the next CPU platform wakeup sequence" "0: Request SP transition to CPU_SP_WAKEUP,1: Request SP transition to the Setpoint when the.." newline hexmask.long.byte 0x0 11.--14. 1. "CPU_SP_WAKEUP,The Setpoint that CPU want the system to transit to on next CPU platform wakeup sequence" newline bitfld.long 0x0 10. "CPU_SP_WAKEUP_EN,1 means enable Setpoint transition on next CPU platform wakeup sequence" "0,1" newline hexmask.long.byte 0x0 6.--9. 1. "CPU_SP_SLEEP,The Setpoint that CPU want the system to transit to on next CPU platform sleep sequence" newline bitfld.long 0x0 5. "CPU_SP_SLEEP_EN,1 means enable Setpoint transition on next CPU platform sleep sequence" "0,1" newline hexmask.long.byte 0x0 1.--4. 1. "CPU_SP_RUN,The Setpoint that CPU want the system to transit to when CPU_SP_RUN_EN is set" newline bitfld.long 0x0 0. "CPU_SP_RUN_EN,Request a Setpoint transition when this bit is set" "0,1" rgroup.long 0x304++0x3 line.long 0x0 "CM_SP_STAT,CM Setpoint Status" hexmask.long.byte 0x0 8.--11. 1. "CPU_SP_TARGET,The requested Setpoint from the CPU platform" newline hexmask.long.byte 0x0 4.--7. 1. "CPU_SP_PREVIOUS,The previous Setpoint of the system" newline hexmask.long.byte 0x0 0.--3. 1. "CPU_SP_CURRENT,The current Setpoint of the system" group.long 0x310++0x4F line.long 0x0 "CM_RUN_MODE_MAPPING,CM Run Mode Setpoint Allowed" hexmask.long.word 0x0 0.--15. 1. "CPU_RUN_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters RUN mode. Each bit stands for 1 Setpoint locked by LOCK_CFG field" line.long 0x4 "CM_WAIT_MODE_MAPPING,CM Wait Mode Setpoint Allowed" hexmask.long.word 0x4 0.--15. 1. "CPU_WAIT_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters WAIT mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0x8 "CM_STOP_MODE_MAPPING,CM Stop Mode Setpoint Allowed" hexmask.long.word 0x8 0.--15. 1. "CPU_STOP_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters STOP mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0xC "CM_SUSPEND_MODE_MAPPING,CM Suspend Mode Setpoint Allowed" hexmask.long.word 0xC 0.--15. 1. "CPU_SUSPEND_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters SUSPEND mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0x10 "CM_SP0_MAPPING,CM Setpoint 0 Mapping" hexmask.long.word 0x10 0.--15. 1. "CPU_SP0_MAPPING,Defines when SP0 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x14 "CM_SP1_MAPPING,CM Setpoint 1 Mapping" hexmask.long.word 0x14 0.--15. 1. "CPU_SP1_MAPPING,Defines when SP1 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x18 "CM_SP2_MAPPING,CM Setpoint 2 Mapping" hexmask.long.word 0x18 0.--15. 1. "CPU_SP2_MAPPING,Defines when SP2 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x1C "CM_SP3_MAPPING,CM Setpoint 3 Mapping" hexmask.long.word 0x1C 0.--15. 1. "CPU_SP3_MAPPING,Defines when SP3 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x20 "CM_SP4_MAPPING,CM Setpoint 4 Mapping" hexmask.long.word 0x20 0.--15. 1. "CPU_SP4_MAPPING,Defines when SP4 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x24 "CM_SP5_MAPPING,CM Setpoint 5 Mapping" hexmask.long.word 0x24 0.--15. 1. "CPU_SP5_MAPPING,Defines when SP5 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x28 "CM_SP6_MAPPING,CM Setpoint 6 Mapping" hexmask.long.word 0x28 0.--15. 1. "CPU_SP6_MAPPING,Defines when SP6 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x2C "CM_SP7_MAPPING,CM Setpoint 7 Mapping" hexmask.long.word 0x2C 0.--15. 1. "CPU_SP7_MAPPING,Defines when SP7 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x30 "CM_SP8_MAPPING,CM Setpoint 8 Mapping" hexmask.long.word 0x30 0.--15. 1. "CPU_SP8_MAPPING,Defines when SP8 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x34 "CM_SP9_MAPPING,CM Setpoint 9 Mapping" hexmask.long.word 0x34 0.--15. 1. "CPU_SP9_MAPPING,Defines when SP9 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x38 "CM_SP10_MAPPING,CM Setpoint 10 Mapping" hexmask.long.word 0x38 0.--15. 1. "CPU_SP10_MAPPING,Defines when SP10 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x3C "CM_SP11_MAPPING,CM Setpoint 11 Mapping" hexmask.long.word 0x3C 0.--15. 1. "CPU_SP11_MAPPING,Defines when SP11 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x40 "CM_SP12_MAPPING,CM Setpoint 12 Mapping" hexmask.long.word 0x40 0.--15. 1. "CPU_SP12_MAPPING,Defines when SP12 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x44 "CM_SP13_MAPPING,CM Setpoint 13 Mapping" hexmask.long.word 0x44 0.--15. 1. "CPU_SP13_MAPPING,Defines when SP13 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x48 "CM_SP14_MAPPING,CM Setpoint 14 Mapping" hexmask.long.word 0x48 0.--15. 1. "CPU_SP14_MAPPING,Defines when SP14 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x4C "CM_SP15_MAPPING,CM Setpoint 15 Mapping" hexmask.long.word 0x4C 0.--15. 1. "CPU_SP15_MAPPING,Defines when SP15 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" group.long 0x380++0x3 line.long 0x0 "CM_STBY_CTRL,CM standby control" rbitfld.long 0x0 17. "STBY_WAKEUP_BUSY,Indicate the CPU is busy exiting standby mode." "0,1" newline rbitfld.long 0x0 16. "STBY_SLEEP_BUSY,Indicate the CPU is busy entering standby mode." "0,1" newline bitfld.long 0x0 2. "STBY_SUSPEND,0x1: Request the chip into standby mode when CPU entering SUSPEND mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." newline bitfld.long 0x0 1. "STBY_STOP,0x1: Request the chip into standby mode when CPU entering STOP mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." newline bitfld.long 0x0 0. "STBY_WAIT,0x1: Request the chip into standby mode when CPU entering WAIT mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." tree.end tree "GPC_CPU_MODE_CTRL_1" base ad:0x40C00800 group.long 0x4++0xF line.long 0x0 "CM_AUTHEN_CTRL,CM Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access CPU mode..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access CPU mode..,1: Allow both privilege and user mode to access CPU.." line.long 0x4 "CM_INT_CTRL,CM Interrupt Control" eventfld.long 0x4 18. "SP_REQ_NOT_ALLOWED_SOFT_INT,sp_req_not_allowed_for_soft interrupt status and clear register" "0,1" newline eventfld.long 0x4 17. "SP_REQ_NOT_ALLOWED_WAKEUP_INT,sp_req_not_allowed_for_wakeup interrupt status and clear register" "0,1" newline eventfld.long 0x4 16. "SP_REQ_NOT_ALLOWED_SLEEP_INT,sp_req_not_allowed_for_sleep interrupt status and clear register" "0,1" newline bitfld.long 0x4 2. "SP_REQ_NOT_ALLOWED_SOFT_INT_EN,sp_req_not_allowed_for_soft interrupt enable" "0: Interrupt disable,1: Interrupt enable" newline bitfld.long 0x4 1. "SP_REQ_NOT_ALLOWED_WAKEUP_INT_EN,sp_req_not_allowed_for_wakeup interrupt enable" "0: Interrupt disable,1: Interrupt enable" newline bitfld.long 0x4 0. "SP_REQ_NOT_ALLOWED_SLEEP_INT_EN,sp_req_not_allowed_for_sleep interrupt enable" "0: Interrupt disable,1: Interrupt enable" line.long 0x8 "CM_MISC,Miscellaneous" bitfld.long 0x8 4. "MASTER_CPU,Master CPU" "0,1" newline rbitfld.long 0x8 2. "SLEEP_HOLD_STAT,Status of cpu_sleep_hold_ack_b" "0,1" newline bitfld.long 0x8 1. "SLEEP_HOLD_EN,Allow cpu_sleep_hold_req assert during CPU low power status" "0: Disable cpu_sleep_hold_req,1: Allow cpu_sleep_hold_req assert during CPU low.." newline rbitfld.long 0x8 0. "NMI_STAT,Non-masked interrupt status" "0: NMI is not asserting,1: NMI is asserting" line.long 0xC "CM_MODE_CTRL,CPU mode control" bitfld.long 0xC 4. "WFE_EN,WFE assertion can be sleep event" "0: WFE assertion can not trigger low power,1: WFE assertion can trigger low power" newline bitfld.long 0xC 0.--1. "CPU_MODE_TARGET,The CPU mode the CPU platform should transit to on next sleep event" "0: Stay in RUN mode,1: Transit to WAIT mode,2: Transit to STOP mode,3: Transit to SUSPEND mode" rgroup.long 0x14++0x3 line.long 0x0 "CM_MODE_STAT,CM CPU mode Status" bitfld.long 0x0 2.--3. "CPU_MODE_PREVIOUS,Previous CPU mode" "0: CPU was previously in RUN mode,1: CPU was previously in WAIT mode,2: CPU was previously in STOP mode,3: CPU was previously in SUSPEND mode" newline bitfld.long 0x0 0.--1. "CPU_MODE_CURRENT,Current CPU mode" "0: CPU is currently in RUN mode,1: CPU is currently in WAIT mode,2: CPU is currently in STOP mode,3: CPU is currently in SUSPEND mode" group.long 0x100++0x1F line.long 0x0 "CM_IRQ_WAKEUP_MASK_0,CM IRQ0~31 wakeup mask" hexmask.long 0x0 0.--31. 1. "IRQ_WAKEUP_MASK_0_31,'1' means the IRQ cannot wakeup CPU platform" line.long 0x4 "CM_IRQ_WAKEUP_MASK_1,CM IRQ32~63 wakeup mask" hexmask.long 0x4 0.--31. 1. "IRQ_WAKEUP_MASK_32_63,'1' means the IRQ cannot wakeup CPU platform" line.long 0x8 "CM_IRQ_WAKEUP_MASK_2,CM IRQ64~95 wakeup mask" hexmask.long 0x8 0.--31. 1. "IRQ_WAKEUP_MASK_64_95,'1' means the IRQ cannot wakeup CPU platform" line.long 0xC "CM_IRQ_WAKEUP_MASK_3,CM IRQ96~127 wakeup mask" hexmask.long 0xC 0.--31. 1. "IRQ_WAKEUP_MASK_96_127,'1' means the IRQ cannot wakeup CPU platform" line.long 0x10 "CM_IRQ_WAKEUP_MASK_4,CM IRQ128~159 wakeup mask" hexmask.long 0x10 0.--31. 1. "IRQ_WAKEUP_MASK_128_159,'1' means the IRQ cannot wakeup CPU platform" line.long 0x14 "CM_IRQ_WAKEUP_MASK_5,CM IRQ160~191 wakeup mask" hexmask.long 0x14 0.--31. 1. "IRQ_WAKEUP_MASK_160_191,'1' means the IRQ cannot wakeup CPU platform" line.long 0x18 "CM_IRQ_WAKEUP_MASK_6,CM IRQ192~223 wakeup mask" hexmask.long 0x18 0.--31. 1. "IRQ_WAKEUP_MASK_192_223,'1' means the IRQ cannot wakeup CPU platform" line.long 0x1C "CM_IRQ_WAKEUP_MASK_7,CM IRQ224~255 wakeup mask" hexmask.long 0x1C 0.--31. 1. "IRQ_WAKEUP_MASK_224_255,'1' means the IRQ cannot wakeup CPU platform" group.long 0x140++0x3 line.long 0x0 "CM_NON_IRQ_WAKEUP_MASK,CM non-irq wakeup mask" bitfld.long 0x0 1. "DEBUG_WAKEUP_MASK,'1' means the debug_wakeup_request cannot wakeup CPU platform" "0,1" newline bitfld.long 0x0 0. "EVENT_WAKEUP_MASK,There are 256 interrupts and 1 event as a wakeup source for GPC. This field masks the 1 event wakeup source." "?,1: The event cannot wakeup CPU platform" rgroup.long 0x150++0x1F line.long 0x0 "CM_IRQ_WAKEUP_STAT_0,CM IRQ0~31 wakeup status" hexmask.long 0x0 0.--31. 1. "IRQ_WAKEUP_STAT_0_31,IRQ status" line.long 0x4 "CM_IRQ_WAKEUP_STAT_1,CM IRQ32~63 wakeup status" hexmask.long 0x4 0.--31. 1. "IRQ_WAKEUP_STAT_32_63,IRQ status" line.long 0x8 "CM_IRQ_WAKEUP_STAT_2,CM IRQ64~95 wakeup status" hexmask.long 0x8 0.--31. 1. "IRQ_WAKEUP_STAT_64_95,IRQ status" line.long 0xC "CM_IRQ_WAKEUP_STAT_3,CM IRQ96~127 wakeup status" hexmask.long 0xC 0.--31. 1. "IRQ_WAKEUP_STAT_96_127,IRQ status" line.long 0x10 "CM_IRQ_WAKEUP_STAT_4,CM IRQ128~159 wakeup status" hexmask.long 0x10 0.--31. 1. "IRQ_WAKEUP_STAT_128_159,IRQ status" line.long 0x14 "CM_IRQ_WAKEUP_STAT_5,CM IRQ160~191 wakeup status" hexmask.long 0x14 0.--31. 1. "IRQ_WAKEUP_STAT_160_191,IRQ status" line.long 0x18 "CM_IRQ_WAKEUP_STAT_6,CM IRQ192~223 wakeup status" hexmask.long 0x18 0.--31. 1. "IRQ_WAKEUP_STAT_192_223,IRQ status" line.long 0x1C "CM_IRQ_WAKEUP_STAT_7,CM IRQ224~255 wakeup status" hexmask.long 0x1C 0.--31. 1. "IRQ_WAKEUP_MASK_224_255,IRQ status" rgroup.long 0x190++0x3 line.long 0x0 "CM_NON_IRQ_WAKEUP_STAT,CM non-irq wakeup status" bitfld.long 0x0 1. "DEBUG_WAKEUP_STAT,Debug wakeup status" "0,1" newline bitfld.long 0x0 0. "EVENT_WAKEUP_STAT,Event wakeup status" "?,1: Interrupt is asserting (pending)" group.long 0x200++0x3 line.long 0x0 "CM_SLEEP_SSAR_CTRL,CM sleep SSAR control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE." group.long 0x208++0x3 line.long 0x0 "CM_SLEEP_LPCG_CTRL,CM sleep LPCG control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x210++0x3 line.long 0x0 "CM_SLEEP_PLL_CTRL,CM sleep PLL control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x218++0x3 line.long 0x0 "CM_SLEEP_ISO_CTRL,CM sleep isolation control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x220++0x3 line.long 0x0 "CM_SLEEP_RESET_CTRL,CM sleep reset control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x228++0x3 line.long 0x0 "CM_SLEEP_POWER_CTRL,CM sleep power control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x290++0x3 line.long 0x0 "CM_WAKEUP_POWER_CTRL,CM wakeup power control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x298++0x3 line.long 0x0 "CM_WAKEUP_RESET_CTRL,CM wakeup reset control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2A0++0x3 line.long 0x0 "CM_WAKEUP_ISO_CTRL,CM wakeup isolation control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2A8++0x3 line.long 0x0 "CM_WAKEUP_PLL_CTRL,CM wakeup PLL control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2B0++0x3 line.long 0x0 "CM_WAKEUP_LPCG_CTRL,CM wakeup LPCG control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2B8++0x3 line.long 0x0 "CM_WAKEUP_SSAR_CTRL,CM wakeup SSAR control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x300++0x3 line.long 0x0 "CM_SP_CTRL,CM Setpoint Control" bitfld.long 0x0 15. "CPU_SP_WAKEUP_SEL,Select the Setpoint transiton on the next CPU platform wakeup sequence" "0: Request SP transition to CPU_SP_WAKEUP,1: Request SP transition to the Setpoint when the.." newline hexmask.long.byte 0x0 11.--14. 1. "CPU_SP_WAKEUP,The Setpoint that CPU want the system to transit to on next CPU platform wakeup sequence" newline bitfld.long 0x0 10. "CPU_SP_WAKEUP_EN,1 means enable Setpoint transition on next CPU platform wakeup sequence" "0,1" newline hexmask.long.byte 0x0 6.--9. 1. "CPU_SP_SLEEP,The Setpoint that CPU want the system to transit to on next CPU platform sleep sequence" newline bitfld.long 0x0 5. "CPU_SP_SLEEP_EN,1 means enable Setpoint transition on next CPU platform sleep sequence" "0,1" newline hexmask.long.byte 0x0 1.--4. 1. "CPU_SP_RUN,The Setpoint that CPU want the system to transit to when CPU_SP_RUN_EN is set" newline bitfld.long 0x0 0. "CPU_SP_RUN_EN,Request a Setpoint transition when this bit is set" "0,1" rgroup.long 0x304++0x3 line.long 0x0 "CM_SP_STAT,CM Setpoint Status" hexmask.long.byte 0x0 8.--11. 1. "CPU_SP_TARGET,The requested Setpoint from the CPU platform" newline hexmask.long.byte 0x0 4.--7. 1. "CPU_SP_PREVIOUS,The previous Setpoint of the system" newline hexmask.long.byte 0x0 0.--3. 1. "CPU_SP_CURRENT,The current Setpoint of the system" group.long 0x310++0x4F line.long 0x0 "CM_RUN_MODE_MAPPING,CM Run Mode Setpoint Allowed" hexmask.long.word 0x0 0.--15. 1. "CPU_RUN_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters RUN mode. Each bit stands for 1 Setpoint locked by LOCK_CFG field" line.long 0x4 "CM_WAIT_MODE_MAPPING,CM Wait Mode Setpoint Allowed" hexmask.long.word 0x4 0.--15. 1. "CPU_WAIT_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters WAIT mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0x8 "CM_STOP_MODE_MAPPING,CM Stop Mode Setpoint Allowed" hexmask.long.word 0x8 0.--15. 1. "CPU_STOP_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters STOP mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0xC "CM_SUSPEND_MODE_MAPPING,CM Suspend Mode Setpoint Allowed" hexmask.long.word 0xC 0.--15. 1. "CPU_SUSPEND_MODE_MAPPING,Defines which Setpoint is allowed when CPU enters SUSPEND mode. Each bit stands for 1 Setpoint locked by LOCK_CFG" line.long 0x10 "CM_SP0_MAPPING,CM Setpoint 0 Mapping" hexmask.long.word 0x10 0.--15. 1. "CPU_SP0_MAPPING,Defines when SP0 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x14 "CM_SP1_MAPPING,CM Setpoint 1 Mapping" hexmask.long.word 0x14 0.--15. 1. "CPU_SP1_MAPPING,Defines when SP1 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x18 "CM_SP2_MAPPING,CM Setpoint 2 Mapping" hexmask.long.word 0x18 0.--15. 1. "CPU_SP2_MAPPING,Defines when SP2 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x1C "CM_SP3_MAPPING,CM Setpoint 3 Mapping" hexmask.long.word 0x1C 0.--15. 1. "CPU_SP3_MAPPING,Defines when SP3 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x20 "CM_SP4_MAPPING,CM Setpoint 4 Mapping" hexmask.long.word 0x20 0.--15. 1. "CPU_SP4_MAPPING,Defines when SP4 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x24 "CM_SP5_MAPPING,CM Setpoint 5 Mapping" hexmask.long.word 0x24 0.--15. 1. "CPU_SP5_MAPPING,Defines when SP5 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x28 "CM_SP6_MAPPING,CM Setpoint 6 Mapping" hexmask.long.word 0x28 0.--15. 1. "CPU_SP6_MAPPING,Defines when SP6 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x2C "CM_SP7_MAPPING,CM Setpoint 7 Mapping" hexmask.long.word 0x2C 0.--15. 1. "CPU_SP7_MAPPING,Defines when SP7 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x30 "CM_SP8_MAPPING,CM Setpoint 8 Mapping" hexmask.long.word 0x30 0.--15. 1. "CPU_SP8_MAPPING,Defines when SP8 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x34 "CM_SP9_MAPPING,CM Setpoint 9 Mapping" hexmask.long.word 0x34 0.--15. 1. "CPU_SP9_MAPPING,Defines when SP9 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x38 "CM_SP10_MAPPING,CM Setpoint 10 Mapping" hexmask.long.word 0x38 0.--15. 1. "CPU_SP10_MAPPING,Defines when SP10 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x3C "CM_SP11_MAPPING,CM Setpoint 11 Mapping" hexmask.long.word 0x3C 0.--15. 1. "CPU_SP11_MAPPING,Defines when SP11 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x40 "CM_SP12_MAPPING,CM Setpoint 12 Mapping" hexmask.long.word 0x40 0.--15. 1. "CPU_SP12_MAPPING,Defines when SP12 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x44 "CM_SP13_MAPPING,CM Setpoint 13 Mapping" hexmask.long.word 0x44 0.--15. 1. "CPU_SP13_MAPPING,Defines when SP13 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x48 "CM_SP14_MAPPING,CM Setpoint 14 Mapping" hexmask.long.word 0x48 0.--15. 1. "CPU_SP14_MAPPING,Defines when SP14 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" line.long 0x4C "CM_SP15_MAPPING,CM Setpoint 15 Mapping" hexmask.long.word 0x4C 0.--15. 1. "CPU_SP15_MAPPING,Defines when SP15 is set as the CPU_SP_TARGET which SP is allowed locked by LOCK_CFG field" group.long 0x380++0x3 line.long 0x0 "CM_STBY_CTRL,CM standby control" rbitfld.long 0x0 17. "STBY_WAKEUP_BUSY,Indicate the CPU is busy exiting standby mode." "0,1" newline rbitfld.long 0x0 16. "STBY_SLEEP_BUSY,Indicate the CPU is busy entering standby mode." "0,1" newline bitfld.long 0x0 2. "STBY_SUSPEND,0x1: Request the chip into standby mode when CPU entering SUSPEND mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." newline bitfld.long 0x0 1. "STBY_STOP,0x1: Request the chip into standby mode when CPU entering STOP mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." newline bitfld.long 0x0 0. "STBY_WAIT,0x1: Request the chip into standby mode when CPU entering WAIT mode locked by LOCK_CFG field." "?,1: Request the chip into standby mode when CPU.." tree.end tree.end tree "GPC_SET_POINT_CTRL" base ad:0x40C02000 group.long 0x4++0x7 line.long 0x0 "SP_AUTHEN_CTRL,SP Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access setpoint..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access setpoint..,1: Allow both privilege and user mode to access.." line.long 0x4 "SP_INT_CTRL,SP Interrupt Control" eventfld.long 0x4 1. "NO_ALLOWED_SP_INT,no_allowed_set_point interrupt" "0,1" newline bitfld.long 0x4 0. "NO_ALLOWED_SP_INT_EN,no_allowed_set_point interrupt enable" "0,1" rgroup.long 0x10++0x7 line.long 0x0 "SP_CPU_REQ,CPU SP Request" hexmask.long.byte 0x0 28.--31. 1. "SP_ACCEPTED_CPU3,CPU3 Setpoint accepted by SP controller" newline hexmask.long.byte 0x0 24.--27. 1. "SP_ACCEPTED_CPU2,CPU2 Setpoint accepted by SP controller" newline hexmask.long.byte 0x0 20.--23. 1. "SP_ACCEPTED_CPU1,CPU1 Setpoint accepted by SP controller" newline hexmask.long.byte 0x0 16.--19. 1. "SP_ACCEPTED_CPU0,CPU0 Setpoint accepted by SP controller" newline hexmask.long.byte 0x0 12.--15. 1. "SP_REQ_CPU3,Setpoint requested by CPU3" newline hexmask.long.byte 0x0 8.--11. 1. "SP_REQ_CPU2,Setpoint requested by CPU2" newline hexmask.long.byte 0x0 4.--7. 1. "SP_REQ_CPU1,Setpoint requested by CPU1" newline hexmask.long.byte 0x0 0.--3. 1. "SP_REQ_CPU0,Setpoint requested by CPU0" line.long 0x4 "SP_SYS_STAT,SP System Status" hexmask.long.byte 0x4 24.--27. 1. "SYS_SP_PREVIOUS,Previous Setpoint only valid when not SP trans busy" newline hexmask.long.byte 0x4 20.--23. 1. "SYS_SP_CURRENT,Current Setpoint only valid when not SP trans busy" newline hexmask.long.byte 0x4 16.--19. 1. "SYS_SP_TARGET,The Setpoint chosen as the target setpoint" newline hexmask.long.word 0x4 0.--15. 1. "SYS_SP_ALLOWED,Allowed Setpoints by all current CPU Setpoint requests" group.long 0x1C++0x3 line.long 0x0 "SP_ROSC_CTRL,SP ROSC Control" hexmask.long.word 0x0 0.--15. 1. "SP_ALLOW_ROSC_OFF,Allow shutting off the ROSC" group.long 0x40++0x7 line.long 0x0 "SP_PRIORITY_0_7,SP0~7 Priority" hexmask.long.byte 0x0 28.--31. 1. "SYS_SP7_PRIORITY,priority of Setpoint 7" newline hexmask.long.byte 0x0 24.--27. 1. "SYS_SP6_PRIORITY,priority of Setpoint 6" newline hexmask.long.byte 0x0 20.--23. 1. "SYS_SP5_PRIORITY,priority of Setpoint 5" newline hexmask.long.byte 0x0 16.--19. 1. "SYS_SP4_PRIORITY,priority of Setpoint 4" newline hexmask.long.byte 0x0 12.--15. 1. "SYS_SP3_PRIORITY,priority of Setpoint 3" newline hexmask.long.byte 0x0 8.--11. 1. "SYS_SP2_PRIORITY,priority of Setpoint 2" newline hexmask.long.byte 0x0 4.--7. 1. "SYS_SP1_PRIORITY,priority of Setpoint 1" newline hexmask.long.byte 0x0 0.--3. 1. "SYS_SP0_PRIORITY,priority of Setpoint 0" line.long 0x4 "SP_PRIORITY_8_15,SP8~15 Priority" hexmask.long.byte 0x4 28.--31. 1. "SYS_SP15_PRIORITY,priority of Setpoint 15" newline hexmask.long.byte 0x4 24.--27. 1. "SYS_SP14_PRIORITY,priority of Setpoint 14" newline hexmask.long.byte 0x4 20.--23. 1. "SYS_SP13_PRIORITY,priority of Setpoint 13" newline hexmask.long.byte 0x4 16.--19. 1. "SYS_SP12_PRIORITY,priority of Setpoint 12" newline hexmask.long.byte 0x4 12.--15. 1. "SYS_SP11_PRIORITY,priority of Setpoint 11" newline hexmask.long.byte 0x4 8.--11. 1. "SYS_SP10_PRIORITY,priority of Setpoint 10" newline hexmask.long.byte 0x4 4.--7. 1. "SYS_SP9_PRIORITY,priority of Setpoint 9" newline hexmask.long.byte 0x4 0.--3. 1. "SYS_SP8_PRIORITY,priority of Setpoint 8" group.long 0x100++0x3 line.long 0x0 "SP_SSAR_SAVE_CTRL,SP SSAR save control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x110++0x3 line.long 0x0 "SP_LPCG_OFF_CTRL,SP LPCG off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x120++0x3 line.long 0x0 "SP_GROUP_DOWN_CTRL,SP group down control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x130++0x3 line.long 0x0 "SP_ROOT_DOWN_CTRL,SP root down control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x140++0x3 line.long 0x0 "SP_PLL_OFF_CTRL,SP PLL off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x150++0x3 line.long 0x0 "SP_ISO_ON_CTRL,SP ISO on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x160++0x3 line.long 0x0 "SP_RESET_EARLY_CTRL,SP reset early control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x170++0x3 line.long 0x0 "SP_POWER_OFF_CTRL,SP power off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x180++0x3 line.long 0x0 "SP_BIAS_OFF_CTRL,SP bias off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x190++0x3 line.long 0x0 "SP_BG_PLDO_OFF_CTRL,SP bandgap and PLL_LDO off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x1A0++0x3 line.long 0x0 "SP_LDO_PRE_CTRL,SP LDO pre control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x1B0++0x3 line.long 0x0 "SP_DCDC_DOWN_CTRL,SP DCDC down control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x200++0x3 line.long 0x0 "SP_DCDC_UP_CTRL,SP DCDC up control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x210++0x3 line.long 0x0 "SP_LDO_POST_CTRL,SP LDO post control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x220++0x3 line.long 0x0 "SP_BG_PLDO_ON_CTRL,SP bandgap and PLL_LDO on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x230++0x3 line.long 0x0 "SP_BIAS_ON_CTRL,SP bias on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x240++0x3 line.long 0x0 "SP_POWER_ON_CTRL,SP power on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x250++0x3 line.long 0x0 "SP_RESET_LATE_CTRL,SP reset late control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x260++0x3 line.long 0x0 "SP_ISO_OFF_CTRL,SP ISO off control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x270++0x3 line.long 0x0 "SP_PLL_ON_CTRL,SP PLL on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x280++0x3 line.long 0x0 "SP_ROOT_UP_CTRL,SP root up control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x290++0x3 line.long 0x0 "SP_GROUP_UP_CTRL,SP group up control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2A0++0x3 line.long 0x0 "SP_LPCG_ON_CTRL,SP LPCG on control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x2B0++0x3 line.long 0x0 "SP_SSAR_RESTORE_CTRL,SP SSAR restore control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" newline bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." newline hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" tree.end tree "GPC_STBY_CTRL" base ad:0x40C02800 group.long 0x4++0x3 line.long 0x0 "STBY_AUTHEN_CTRL,Standby Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" group.long 0xC++0x3 line.long 0x0 "STBY_MISC,STBY Misc" bitfld.long 0x0 3. "FORCE_CPU3_STBY,Force CPU3 requesting standby mode" "0,1" bitfld.long 0x0 2. "FORCE_CPU2_STBY,Force CPU2 requesting standby mode" "0,1" bitfld.long 0x0 1. "FORCE_CPU1_STBY,Force CPU0 requesting standby mode" "0,1" newline bitfld.long 0x0 0. "FORCE_CPU0_STBY,Force CPU0 requesting standby mode" "0,1" group.long 0xF0++0x3 line.long 0x0 "STBY_LPCG_IN_CTRL,STBY lpcg_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x100++0x3 line.long 0x0 "STBY_PLL_IN_CTRL,STBY pll_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x110++0x3 line.long 0x0 "STBY_BIAS_IN_CTRL,STBY bias_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x120++0x3 line.long 0x0 "STBY_PLDO_IN_CTRL,STBY pldo_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x128++0x3 line.long 0x0 "STBY_BANDGAP_IN_CTRL,STBY bandgap_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x130++0x3 line.long 0x0 "STBY_LDO_IN_CTRL,STBY ldo_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x140++0x3 line.long 0x0 "STBY_DCDC_IN_CTRL,STBY dcdc_in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x150++0x3 line.long 0x0 "STBY_PMIC_IN_CTRL,STBY PMIC in control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x200++0x3 line.long 0x0 "STBY_PMIC_OUT_CTRL,STBY PMIC out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x210++0x3 line.long 0x0 "STBY_DCDC_OUT_CTRL,STBY DCDC out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x220++0x3 line.long 0x0 "STBY_LDO_OUT_CTRL,STBY LDO out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x230++0x3 line.long 0x0 "STBY_BANDGAP_OUT_CTRL,STBY bandgap out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x238++0x3 line.long 0x0 "STBY_PLDO_OUT_CTRL,STBY pldo out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x240++0x3 line.long 0x0 "STBY_BIAS_OUT_CTRL,STBY bias out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x250++0x3 line.long 0x0 "STBY_PLL_OUT_CTRL,STBY PLL out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" group.long 0x260++0x3 line.long 0x0 "STBY_LPCG_OUT_CTRL,STBY LPCG out control" bitfld.long 0x0 31. "DISABLE,Disable this step" "0,1" bitfld.long 0x0 28.--29. "CNT_MODE,Count mode" "0: Counter disable mode: not use step counter step..,1: Counter delay mode: delay after receiving..,2: Ignore step_done response the counter starts to..,3: Time out mode the counter starts to count once.." hexmask.long.word 0x0 0.--15. 1. "STEP_CNT,Step count useage is depending on CNT_MODE" tree.end tree.end tree "GPIO" base ad:0x0 tree "CM7_GPIO2 (GPIO)" base ad:0x42008000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "CM7_GPIO3 (GPIO)" base ad:0x4200C000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO1" base ad:0x4012C000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO2" base ad:0x40130000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO3" base ad:0x40134000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO4" base ad:0x40138000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO5" base ad:0x4013C000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO6" base ad:0x40140000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO7" base ad:0x40C5C000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO8" base ad:0x40C60000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO9" base ad:0x40C64000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO10" base ad:0x40C68000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO11" base ad:0x40C6C000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO12" base ad:0x40C70000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree "GPIO13" base ad:0x40CA0000 group.long 0x0++0x7 line.long 0x0 "DR,GPIO data register" hexmask.long 0x0 0.--31. 1. "DR,DR data bits" line.long 0x4 "GDIR,GPIO direction register" hexmask.long 0x4 0.--31. 1. "GDIR,GPIO direction bits" rgroup.long 0x8++0x3 line.long 0x0 "PSR,GPIO pad status register" hexmask.long 0x0 0.--31. 1. "PSR,GPIO pad status bits" group.long 0xC++0x13 line.long 0x0 "ICR1,GPIO interrupt configuration register1" bitfld.long 0x0 30.--31. "ICR15,Interrupt configuration field for GPIO interrupt 15" "0: Interrupt 15 is low-level sensitive.,1: Interrupt 15 is high-level sensitive.,2: Interrupt 15 is rising-edge sensitive.,3: Interrupt 15 is falling-edge sensitive." bitfld.long 0x0 28.--29. "ICR14,Interrupt configuration field for GPIO interrupt 14" "0: Interrupt 14 is low-level sensitive.,1: Interrupt 14 is high-level sensitive.,2: Interrupt 14 is rising-edge sensitive.,3: Interrupt 14 is falling-edge sensitive." newline bitfld.long 0x0 26.--27. "ICR13,Interrupt configuration field for GPIO interrupt 13" "0: Interrupt 13 is low-level sensitive.,1: Interrupt 13 is high-level sensitive.,2: Interrupt 13 is rising-edge sensitive.,3: Interrupt 13 is falling-edge sensitive." bitfld.long 0x0 24.--25. "ICR12,Interrupt configuration field for GPIO interrupt 12" "0: Interrupt 12 is low-level sensitive.,1: Interrupt 12 is high-level sensitive.,2: Interrupt 12 is rising-edge sensitive.,3: Interrupt 12 is falling-edge sensitive." newline bitfld.long 0x0 22.--23. "ICR11,Interrupt configuration field for GPIO interrupt 11" "0: Interrupt 11 is low-level sensitive.,1: Interrupt 11 is high-level sensitive.,2: Interrupt 11 is rising-edge sensitive.,3: Interrupt 11 is falling-edge sensitive." bitfld.long 0x0 20.--21. "ICR10,Interrupt configuration field for GPIO interrupt 10" "0: Interrupt 10 is low-level sensitive.,1: Interrupt 10 is high-level sensitive.,2: Interrupt 10 is rising-edge sensitive.,3: Interrupt 10 is falling-edge sensitive." newline bitfld.long 0x0 18.--19. "ICR9,Interrupt configuration field for GPIO interrupt 9" "0: Interrupt 9 is low-level sensitive.,1: Interrupt 9 is high-level sensitive.,2: Interrupt 9 is rising-edge sensitive.,3: Interrupt 9 is falling-edge sensitive." bitfld.long 0x0 16.--17. "ICR8,Interrupt configuration field for GPIO interrupt 8" "0: Interrupt 8 is low-level sensitive.,1: Interrupt 8 is high-level sensitive.,2: Interrupt 8 is rising-edge sensitive.,3: Interrupt 8 is falling-edge sensitive." newline bitfld.long 0x0 14.--15. "ICR7,Interrupt configuration field for GPIO interrupt 7" "0: Interrupt 7 is low-level sensitive.,1: Interrupt 7 is high-level sensitive.,2: Interrupt 7 is rising-edge sensitive.,3: Interrupt 7 is falling-edge sensitive." bitfld.long 0x0 12.--13. "ICR6,Interrupt configuration field for GPIO interrupt 6" "0: Interrupt 6 is low-level sensitive.,1: Interrupt 6 is high-level sensitive.,2: Interrupt 6 is rising-edge sensitive.,3: Interrupt 6 is falling-edge sensitive." newline bitfld.long 0x0 10.--11. "ICR5,Interrupt configuration field for GPIO interrupt 5" "0: Interrupt 5 is low-level sensitive.,1: Interrupt 5 is high-level sensitive.,2: Interrupt 5 is rising-edge sensitive.,3: Interrupt 5 is falling-edge sensitive." bitfld.long 0x0 8.--9. "ICR4,Interrupt configuration field for GPIO interrupt 4" "0: Interrupt 4 is low-level sensitive.,1: Interrupt 4 is high-level sensitive.,2: Interrupt 4 is rising-edge sensitive.,3: Interrupt 4 is falling-edge sensitive." newline bitfld.long 0x0 6.--7. "ICR3,Interrupt configuration field for GPIO interrupt 3" "0: Interrupt 3 is low-level sensitive.,1: Interrupt 3 is high-level sensitive.,2: Interrupt 3 is rising-edge sensitive.,3: Interrupt 3 is falling-edge sensitive." bitfld.long 0x0 4.--5. "ICR2,Interrupt configuration field for GPIO interrupt 2" "0: Interrupt 2 is low-level sensitive.,1: Interrupt 2 is high-level sensitive.,2: Interrupt 2 is rising-edge sensitive.,3: Interrupt 2 is falling-edge sensitive." newline bitfld.long 0x0 2.--3. "ICR1,Interrupt configuration field for GPIO interrupt 1" "0: Interrupt 1 is low-level sensitive.,1: Interrupt 1 is high-level sensitive.,2: Interrupt 1 is rising-edge sensitive.,3: Interrupt 1 is falling-edge sensitive." bitfld.long 0x0 0.--1. "ICR0,Interrupt configuration field for GPIO interrupt 0" "0: Interrupt 0 is low-level sensitive.,1: Interrupt 0 is high-level sensitive.,2: Interrupt 0 is rising-edge sensitive.,3: Interrupt 0 is falling-edge sensitive." line.long 0x4 "ICR2,GPIO interrupt configuration register2" bitfld.long 0x4 30.--31. "ICR31,Interrupt configuration field for GPIO interrupt 31" "0: Interrupt 31 is low-level sensitive.,1: Interrupt 31 is high-level sensitive.,2: Interrupt 31 is rising-edge sensitive.,3: Interrupt 31 is falling-edge sensitive." bitfld.long 0x4 28.--29. "ICR30,Interrupt configuration field for GPIO interrupt 30" "0: Interrupt 30 is low-level sensitive.,1: Interrupt 30 is high-level sensitive.,2: Interrupt 30 is rising-edge sensitive.,3: Interrupt 30 is falling-edge sensitive." newline bitfld.long 0x4 26.--27. "ICR29,Interrupt configuration field for GPIO interrupt 29" "0: Interrupt 29 is low-level sensitive.,1: Interrupt 29 is high-level sensitive.,2: Interrupt 29 is rising-edge sensitive.,3: Interrupt 29 is falling-edge sensitive." bitfld.long 0x4 24.--25. "ICR28,Interrupt configuration field for GPIO interrupt 28" "0: Interrupt 28 is low-level sensitive.,1: Interrupt 28 is high-level sensitive.,2: Interrupt 28 is rising-edge sensitive.,3: Interrupt 28 is falling-edge sensitive." newline bitfld.long 0x4 22.--23. "ICR27,Interrupt configuration field for GPIO interrupt 27" "0: Interrupt 27 is low-level sensitive.,1: Interrupt 27 is high-level sensitive.,2: Interrupt 27 is rising-edge sensitive.,3: Interrupt 27 is falling-edge sensitive." bitfld.long 0x4 20.--21. "ICR26,Interrupt configuration field for GPIO interrupt 26" "0: Interrupt 26 is low-level sensitive.,1: Interrupt 26 is high-level sensitive.,2: Interrupt 26 is rising-edge sensitive.,3: Interrupt 26 is falling-edge sensitive." newline bitfld.long 0x4 18.--19. "ICR25,Interrupt configuration field for GPIO interrupt 25" "0: Interrupt 25 is low-level sensitive.,1: Interrupt 25 is high-level sensitive.,2: Interrupt 25 is rising-edge sensitive.,3: Interrupt 25 is falling-edge sensitive." bitfld.long 0x4 16.--17. "ICR24,Interrupt configuration field for GPIO interrupt 24" "0: Interrupt 24 is low-level sensitive.,1: Interrupt 24 is high-level sensitive.,2: Interrupt 24 is rising-edge sensitive.,3: Interrupt 24 is falling-edge sensitive." newline bitfld.long 0x4 14.--15. "ICR23,Interrupt configuration field for GPIO interrupt 23" "0: Interrupt 23 is low-level sensitive.,1: Interrupt 23 is high-level sensitive.,2: Interrupt 23 is rising-edge sensitive.,3: Interrupt 23 is falling-edge sensitive." bitfld.long 0x4 12.--13. "ICR22,Interrupt configuration field for GPIO interrupt 22" "0: Interrupt 22 is low-level sensitive.,1: Interrupt 22 is high-level sensitive.,2: Interrupt 22 is rising-edge sensitive.,3: Interrupt 22 is falling-edge sensitive." newline bitfld.long 0x4 10.--11. "ICR21,Interrupt configuration field for GPIO interrupt 21" "0: Interrupt 21 is low-level sensitive.,1: Interrupt 21 is high-level sensitive.,2: Interrupt 21 is rising-edge sensitive.,3: Interrupt 21 is falling-edge sensitive." bitfld.long 0x4 8.--9. "ICR20,Interrupt configuration field for GPIO interrupt 20" "0: Interrupt 20 is low-level sensitive.,1: Interrupt 20 is high-level sensitive.,2: Interrupt 20 is rising-edge sensitive.,3: Interrupt 20 is falling-edge sensitive." newline bitfld.long 0x4 6.--7. "ICR19,Interrupt configuration field for GPIO interrupt 19" "0: Interrupt 19 is low-level sensitive.,1: Interrupt 19 is high-level sensitive.,2: Interrupt 19 is rising-edge sensitive.,3: Interrupt 19 is falling-edge sensitive." bitfld.long 0x4 4.--5. "ICR18,Interrupt configuration field for GPIO interrupt 18" "0: Interrupt 18 is low-level sensitive.,1: Interrupt 18 is high-level sensitive.,2: Interrupt 18 is rising-edge sensitive.,3: Interrupt 18 is falling-edge sensitive." newline bitfld.long 0x4 2.--3. "ICR17,Interrupt configuration field for GPIO interrupt 17" "0: Interrupt 17 is low-level sensitive.,1: Interrupt 17 is high-level sensitive.,2: Interrupt 17 is rising-edge sensitive.,3: Interrupt 17 is falling-edge sensitive." bitfld.long 0x4 0.--1. "ICR16,Interrupt configuration field for GPIO interrupt 16" "0: Interrupt 16 is low-level sensitive.,1: Interrupt 16 is high-level sensitive.,2: Interrupt 16 is rising-edge sensitive.,3: Interrupt 16 is falling-edge sensitive." line.long 0x8 "IMR,GPIO interrupt mask register" hexmask.long 0x8 0.--31. 1. "IMR,Interrupt Mask bits" line.long 0xC "ISR,GPIO interrupt status register" hexmask.long 0xC 0.--31. 1. "ISR,Interrupt status bits" line.long 0x10 "EDGE_SEL,GPIO edge select register" hexmask.long 0x10 0.--31. 1. "GPIO_EDGE_SEL,Edge select" wgroup.long 0x84++0xB line.long 0x0 "DR_SET,GPIO data register SET" hexmask.long 0x0 0.--31. 1. "DR_SET,Set" line.long 0x4 "DR_CLEAR,GPIO data register CLEAR" hexmask.long 0x4 0.--31. 1. "DR_CLEAR,Clear" line.long 0x8 "DR_TOGGLE,GPIO data register TOGGLE" hexmask.long 0x8 0.--31. 1. "DR_TOGGLE,Toggle" tree.end tree.end tree "GPT" base ad:0x0 tree "GPT1" base ad:0x400EC000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree "GPT2" base ad:0x400F0000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree "GPT3" base ad:0x400F4000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree "GPT4" base ad:0x400F8000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree "GPT5" base ad:0x400FC000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree "GPT6" base ad:0x40100000 group.long 0x0++0xF line.long 0x0 "CR,GPT Control Register" bitfld.long 0x0 31. "FO3,Force Output Compare for Channel 3" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 30. "FO2,Force Output Compare for Channel 2" "0: No effect,1: Trigger the programmed response on the pin" newline bitfld.long 0x0 29. "FO1,Force Output Compare for Channel 1" "0: No effect,1: Trigger the programmed response on the pin" bitfld.long 0x0 26.--28. "OM3,Output Compare Operating Mode for Channel 3" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 23.--25. "OM2,Output Compare Operating Mode for Channel 2" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." bitfld.long 0x0 20.--22. "OM1,Output Compare Operating Mode for Channel 1" "0: Generate a low pulse that is one input clock..,1: Toggle output pin,2: Clear output pin,3: Set output pin,4: Generate a low pulse that is one input clock..,5: Generate a low pulse that is one input clock..,6: Generate a low pulse that is one input clock..,7: Generate a low pulse that is one input clock.." newline bitfld.long 0x0 18.--19. "IM2,Input Capture Operating Mode for Channel 2" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" bitfld.long 0x0 16.--17. "IM1,Input Capture Operating Mode for Channel 1" "0: Capture disabled,1: Capture on rising edge only,2: Capture on falling edge only,3: Capture on both edges" newline bitfld.long 0x0 15. "SWR,Software Reset" "0: GPT is not in software reset state,1: GPT is in software reset state" bitfld.long 0x0 10. "EN_24M,Enable Oscillator Clock Input" "0: Disable,1: Enable" newline bitfld.long 0x0 9. "FRR,Free-Run or Restart Mode" "0: Restart mode. After a compare event the counter..,1: Free-Run mode. After a compare event the counter.." bitfld.long 0x0 6.--8. "CLKSRC,Clock Source Select" "0: No clock,1: Peripheral Clock (ipg_clk),2: High Frequency Reference Clock (ipg_clk_highfreq),3: External Clock,4: Low Frequency Reference Clock (ipg_clk_32k),5: Oscillator as Reference Clock (ipg_clk_16M),?,?" newline bitfld.long 0x0 5. "STOPEN,GPT Stop Mode Enable" "0: Disable in Stop mode,1: Enable in Stop mode" bitfld.long 0x0 4. "DOZEEN,GPT Doze Mode Enable" "0: Disable in Doze mode,1: Enable in Doze mode" newline bitfld.long 0x0 3. "WAITEN,GPT Wait Mode Enable" "0: Disable in Wait mode,1: Enable in Wait mode" bitfld.long 0x0 2. "DBGEN,GPT Debug Mode Enable" "0: Disable in Debug mode,1: Enable in Debug mode" newline bitfld.long 0x0 1. "ENMOD,GPT Enable Mode" "0: Restart counting from their frozen values after..,1: Reset counting from 0 after GPT is enabled (EN=1)." bitfld.long 0x0 0. "EN,GPT Enable" "0: Disable,1: Enable" line.long 0x4 "PR,GPT Prescaler Register" hexmask.long.byte 0x4 12.--15. 1. "PRESCALER24M,Prescaler divide value for the oscillator clock" hexmask.long.word 0x4 0.--11. 1. "PRESCALER,Prescaler divide value" line.long 0x8 "SR,GPT Status Register" eventfld.long 0x8 5. "ROV,Rollover Flag" "0: Rollover has not occurred.,1: Rollover has occurred." eventfld.long 0x8 4. "IF2,Input Capture Flag for Channel 2" "0: Capture event has not occurred.,1: Capture event has occurred." newline eventfld.long 0x8 3. "IF1,Input Capture Flag for Channel 1" "0: Capture event has not occurred.,1: Capture event has occurred." eventfld.long 0x8 2. "OF3,Output Compare Flag for Channel 3" "0: Compare event has not occurred.,1: Compare event has occurred." newline eventfld.long 0x8 1. "OF2,Output Compare Flag for Channel 2" "0: Compare event has not occurred.,1: Compare event has occurred." eventfld.long 0x8 0. "OF1,Output Compare Flag for Channel 1" "0: Compare event has not occurred.,1: Compare event has occurred." line.long 0xC "IR,GPT Interrupt Register" bitfld.long 0xC 5. "ROVIE,Rollover Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 4. "IF2IE,Input Capture Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 3. "IF1IE,Input Capture Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 2. "OF3IE,Output Compare Flag for Channel 3 Interrupt Enable" "0: Disable,1: Enable" newline bitfld.long 0xC 1. "OF2IE,Output Compare Flag for Channel 2 Interrupt Enable" "0: Disable,1: Enable" bitfld.long 0xC 0. "OF1IE,Output Compare Flag for Channel 1 Interrupt Enable" "0: Disable,1: Enable" repeat 3. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "OCR$1,GPT Output Compare Register" hexmask.long 0x0 0.--31. 1. "COMP,Compare Value" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x1C)++0x3 line.long 0x0 "ICR$1,GPT Input Capture Register" hexmask.long 0x0 0.--31. 1. "CAPT,Capture Value" repeat.end rgroup.long 0x24++0x3 line.long 0x0 "CNT,GPT Counter Register" hexmask.long 0x0 0.--31. 1. "COUNT,Counter Value" tree.end tree.end tree "IEE" base ad:0x0 tree "IEE_APC" base ad:0x40068000 group.long 0x0++0x7F line.long 0x0 "REGION0_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x0 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x4 "REGION0_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x4 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x8 "REGION0_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x8 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x8 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0xC "REGION0_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0xC 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0xC 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x10 "REGION1_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x10 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x14 "REGION1_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x14 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x18 "REGION1_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x18 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x18 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x1C "REGION1_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x1C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x1C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x20 "REGION2_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x20 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x24 "REGION2_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x24 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x28 "REGION2_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x28 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x28 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x2C "REGION2_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x2C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x2C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x30 "REGION3_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x30 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x34 "REGION3_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x34 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x38 "REGION3_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x38 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x38 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x3C "REGION3_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x3C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x3C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x40 "REGION4_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x40 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x44 "REGION4_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x44 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x48 "REGION4_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x48 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x48 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x4C "REGION4_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x4C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x4C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x50 "REGION5_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x50 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x54 "REGION5_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x54 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x58 "REGION5_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x58 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x58 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x5C "REGION5_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x5C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x5C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x60 "REGION6_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x60 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x64 "REGION6_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x64 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x68 "REGION6_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x68 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x68 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x6C "REGION6_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x6C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x6C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x70 "REGION7_TOP_ADDR,End address of IEE region (n)" hexmask.long 0x70 0.--28. 1. "TOP_ADDR,End address of IEE region" line.long 0x74 "REGION7_BOT_ADDR,Start address of IEE region (n)" hexmask.long 0x74 0.--28. 1. "BOT_ADDR,Start address of IEE region" line.long 0x78 "REGION7_RDC_D0,Region control of core domain 0 for region (n)" bitfld.long 0x78 1. "RDC_D0_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x78 0. "RDC_D0_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." line.long 0x7C "REGION7_RDC_D1,Region control of core domain 1 for region (n)" bitfld.long 0x7C 1. "RDC_D1_LOCK,Lock bit for bit 0" "0: Bit 0 is unlocked,1: Bit 0 is locked" bitfld.long 0x7C 0. "RDC_D1_WRITE_DIS,Write disable of core domain 1" "0: Write to TOP_ADDR and BOT_ADDR of this region..,1: Write to TOP_ADDR and BOT_ADDR of this region.." tree.end tree "IEE_RT1170" base ad:0x4006C000 group.long 0x0++0x3 line.long 0x0 "GCFG,IEE Global Configuration" bitfld.long 0x0 31. "RST,Reset bit" "0: Do Not Reset.,1: Reset IEE." bitfld.long 0x0 29. "CLR_MON,Clear monitor bit" "0: Do not reset.,1: Reset performance counters." newline bitfld.long 0x0 28. "MON_EN,Monitor enable bit" "0: Performance monitoring disabled. Writing of the..,1: Performance monitoring enabled. Writing of the.." bitfld.long 0x0 25. "KEY_RD_DIS,Key read disable bit" "0: Key read enabled. Reading the key registers is..,1: Key read disabled. Reading the key registers is.." newline bitfld.long 0x0 17. "TMD,Test mode disable bit" "0: Test mode is usable.,1: Test mode is disabled." bitfld.long 0x0 16. "TME,Test mode enable bit" "0: Disabled.,1: Enabled." newline bitfld.long 0x0 7. "RL7,Region lock 7 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." bitfld.long 0x0 6. "RL6,Region lock 6 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." newline bitfld.long 0x0 5. "RL5,Region lock 5 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." bitfld.long 0x0 4. "RL4,Region lock 4 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." newline bitfld.long 0x0 3. "RL3,Region lock 3 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." bitfld.long 0x0 2. "RL2,Region lock 2 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." newline bitfld.long 0x0 1. "RL1,Region lock 1 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." bitfld.long 0x0 0. "RL0,Region lock 0 bit" "0: Unlocked.,1: Key Offset and Attribute registers are locked." rgroup.long 0x4++0x3 line.long 0x0 "STA,IEE Status" bitfld.long 0x0 4. "AFD,AES fault detected bit" "0: No fault detected,1: Fault detected" bitfld.long 0x0 0. "DSR,DPA seed request bit" "0: No seed request present,1: Seed request present" group.long 0x8++0x3 line.long 0x0 "TSTMD,IEE Test Mode Register" hexmask.long.byte 0x0 8.--11. 1. "TMLEN,Test mode length field" rbitfld.long 0x0 4. "TMDONE,Test mode done bit" "0: Not Done.,1: Test Done." newline bitfld.long 0x0 3. "TMCONT,Test mode continue bit. Set to indicate that operation will be followed by more data." "0: Do not continue. This is the last block of data..,1: Continue. Do not initialize AES after this block." bitfld.long 0x0 2. "TMENCR,Test mode encrypt/decrypt bit." "0: AES Test mode will do decryption.,1: AES Test mode will do encryption." newline bitfld.long 0x0 1. "TMR,Test mode run bit" "0: Not running. May be written if IEE_GCFG[TME] = 1,1: Run AES Test until TMDONE is indicated." rbitfld.long 0x0 0. "TMRDY,Test mode ready bit. All AXI transactions have stopped and test can begin." "0: Not Ready.,1: Ready." wgroup.long 0xC++0x3 line.long 0x0 "DPAMS,AES Mask Generation Seed" hexmask.long 0x0 0.--31. 1. "DPAMS,DPA mask seed" group.long 0x20++0x7 line.long 0x0 "PC_S_LT,Performance Counter. AES Slave Latency Threshold Value" hexmask.long.word 0x0 16.--31. 1. "SR_LT,Slave read latency threshold in AXI clock cycles." hexmask.long.word 0x0 0.--15. 1. "SW_LT,Slave write latency threshold in AXI clock cycles." line.long 0x4 "PC_M_LT,Performance Counter. AES Master Latency Threshold" hexmask.long.word 0x4 16.--27. 1. "MR_LT,Master read latency threshold in AXI clock cycles." hexmask.long.word 0x4 0.--11. 1. "MW_LT,Master write latency threshold in AXI clock cycles." group.long 0x40++0x7 line.long 0x0 "PC_BLK_ENC,Performance Counter. Number of AES Block Encryptions" hexmask.long 0x0 0.--31. 1. "BLK_ENC,Number of AES block encryptions. Does not roll over if value maxes out." line.long 0x4 "PC_BLK_DEC,Performance Counter. Number of AES Block Decryptions" hexmask.long 0x4 0.--31. 1. "BLK_DEC,Number of AES block decryptions. Does not roll over if value maxes out." group.long 0x50++0xF line.long 0x0 "PC_SR_TRANS,Performance Counter. Number of AXI Slave Read Transactions" hexmask.long 0x0 0.--31. 1. "SR_TRANS,Number of slave read transactions." line.long 0x4 "PC_SW_TRANS,Performance Counter. Number of AXI Slave Write Transactions" hexmask.long 0x4 0.--31. 1. "SW_TRANS,Number of slave write transactions." line.long 0x8 "PC_MR_TRANS,Performance Counter. Number of AXI Master Read Transactions" hexmask.long 0x8 0.--31. 1. "MR_TRANS,Number of master read transactions." line.long 0xC "PC_MW_TRANS,Performance Counter. Number of AXI Master Write Transactions" hexmask.long 0xC 0.--31. 1. "MW_TRANS,Number of master write transactions." group.long 0x64++0x3 line.long 0x0 "PC_M_MBR,Performance Counter. Number of AXI Master Merge Buffer Read Transactions" hexmask.long 0x0 0.--31. 1. "M_MBR,Number of master merge buffer read transactions." group.long 0x70++0x5F line.long 0x0 "PC_SR_TBC_U,Performance Counter. Upper Slave Read Transactions Byte Count" hexmask.long.word 0x0 0.--15. 1. "SR_TBC,Number of bytes in slave read transactions. Upper 16 bits of SR_TBC[47:0]." line.long 0x4 "PC_SR_TBC_L,Performance Counter. Lower Slave Read Transactions Byte Count" hexmask.long 0x4 0.--31. 1. "SR_TBC,Number of bytes in slave read transactions. Lower 32 bits of SR_TBC[47:0]." line.long 0x8 "PC_SW_TBC_U,Performance Counter. Upper Slave Write Transactions Byte Count" hexmask.long.word 0x8 0.--15. 1. "SW_TBC,Number of bytes in slave write transactions. Upper 16 bits of SW_TBC[47:0]." line.long 0xC "PC_SW_TBC_L,Performance Counter. Lower Slave Write Transactions Byte Count" hexmask.long 0xC 0.--31. 1. "SW_TBC,Number of bytes in slave write transactions. Lower 32 bits of SW_TBC[47:0]." line.long 0x10 "PC_MR_TBC_U,Performance Counter. Upper Master Read Transactions Byte Count" hexmask.long.word 0x10 0.--15. 1. "MR_TBC,Number of bytes in master read transactions. 44 MSBs. Upper 16 bits of MR_TBC[43:0]." line.long 0x14 "PC_MR_TBC_L,Performance Counter. Lower Master Read Transactions Byte Count" hexmask.long 0x14 4.--31. 1. "MR_TBC,Number of bytes in master read transactions. 44 MSBs. Lower 28 bits of MR_TBC[43:0]." hexmask.long.byte 0x14 0.--3. 1. "MR_TBC_LSB,Number of bytes in master read transactions. 4 LSBs always 0." line.long 0x18 "PC_MW_TBC_U,Performance Counter. Upper Master Write Transactions Byte Count" hexmask.long.word 0x18 0.--15. 1. "MW_TBC,Number of bytes in master write transactions. 44 MSBs. Upper 16 bits of MW_TBC[43:0]." line.long 0x1C "PC_MW_TBC_L,Performance Counter. Lower Master Write Transactions Byte Count" hexmask.long 0x1C 4.--31. 1. "MW_TBC,Number of bytes in master write transactions. 44 MSBs. Lower 28 bits of MR_TBC[43:0]." hexmask.long.byte 0x1C 0.--3. 1. "MW_TBC_LSB,Number of bytes in master write transactions. 4 LSBs always 0." line.long 0x20 "PC_SR_TLGTT,Performance Counter. Number of AXI Slave Read Transactions with Latency Greater than the Threshold" hexmask.long 0x20 0.--31. 1. "SR_TLGTT,Number of slave read transactions with latency greater than the threshold." line.long 0x24 "PC_SW_TLGTT,Performance Counter. Number of AXI Slave Write Transactions with Latency Greater than the Threshold" hexmask.long 0x24 0.--31. 1. "SW_TLGTT,Number of slave write transactions with latency greater than the threshold." line.long 0x28 "PC_MR_TLGTT,Performance Counter. Number of AXI Master Read Transactions with Latency Greater than the Threshold" hexmask.long 0x28 0.--31. 1. "MR_TLGTT,Number of master read transactions with latency greater than the threshold." line.long 0x2C "PC_MW_TLGTT,Performance Counter. Number of AXI Master Write Transactions with Latency Greater than the Threshold" hexmask.long 0x2C 0.--31. 1. "MW_TGTT,Number of master write transactions with latency greater than the threshold." line.long 0x30 "PC_SR_TLAT_U,Performance Counter. Upper Slave Read Latency Count" hexmask.long.word 0x30 0.--15. 1. "SR_TLAT,Total slave read latency in AXI clock cycles. Upper 16 bits of SR_TLAT[47:0]." line.long 0x34 "PC_SR_TLAT_L,Performance Counter. Lower Slave Read Latency Count" hexmask.long 0x34 0.--31. 1. "SR_TLAT,Total slave read latency in AXI clock cycles. Lower 32 bits of SR_TLAT[47:0]." line.long 0x38 "PC_SW_TLAT_U,Performance Counter. Upper Slave Write Latency Count" hexmask.long.word 0x38 0.--15. 1. "SW_TLAT,Total slave write latency in AXI clock cycles. Upper 16 bits of SW_TLAT[47:0]." line.long 0x3C "PC_SW_TLAT_L,Performance Counter. Lower Slave Write Latency Count" hexmask.long 0x3C 0.--31. 1. "SW_TLAT,Total slave write latency in AXI clock cycles. Lower 32 bits of SW_TLAT[47:0]." line.long 0x40 "PC_MR_TLAT_U,Performance Counter. Upper Master Read Latency Count" hexmask.long.word 0x40 0.--15. 1. "MR_TLAT,Total master read latency in AXI clock cycles. Upper 16 bits of MR_TLAT[47:0]." line.long 0x44 "PC_MR_TLAT_L,Performance Counter. Lower Master Read Latency Count" hexmask.long 0x44 0.--31. 1. "MR_TLAT,Total master read latency in AXI clock cycles. Lower 32 bits of MR_TLAT[47:0]." line.long 0x48 "PC_MW_TLAT_U,Performance Counter. Upper Master Write Latency Count" hexmask.long.word 0x48 0.--15. 1. "MW_TLAT,Total master write latency in AXI clock cycles. Upper 16 bits of MW_TLAT[47:0]." line.long 0x4C "PC_MW_TLAT_L,Performance Counter. Lower Master Write Latency Count" hexmask.long 0x4C 0.--31. 1. "MW_TLAT,Total master write latency in AXI clock cycles. Lower 32 bits of MW_TLAT[47:0]." line.long 0x50 "PC_SR_TNRT_U,Performance Counter. Upper Slave Read Total Non-Responding Time" hexmask.long.word 0x50 0.--15. 1. "SR_TNRT,Total slave read non-responding time in AXI clock cycles. Upper 16 bits of SR_TNRT[47:0]." line.long 0x54 "PC_SR_TNRT_L,Performance Counter. Lower Slave Read Total Non-Responding Time" hexmask.long 0x54 0.--31. 1. "SR_TNRT,Total slave read non-responding time in AXI clock cycles. Lower 32 bits of SR_TNRT[47:0]." line.long 0x58 "PC_SW_TNRT_U,Performance Counter. Upper Slave Write Total Non-Responding Time" hexmask.long.word 0x58 0.--15. 1. "SW_TNRT,Total slave write non-responding time in AXI clock cycles. Upper 16 bits of SW_TNRT[47:0]." line.long 0x5C "PC_SW_TNRT_L,Performance Counter. Lower Slave Write Total Non-Responding Time" hexmask.long 0x5C 0.--31. 1. "SW_TNRT,Total slave write non-responding time in AXI clock cycles. Lower 32 bits of SW_TNRT[47:0]." rgroup.long 0xF0++0x3 line.long 0x0 "VIDR1,IEE Version ID Register 1" hexmask.long.word 0x0 16.--31. 1. "IP_ID,ID for IEE." hexmask.long.byte 0x0 8.--15. 1. "MAJ_REV,Major revision number for IEE." newline hexmask.long.byte 0x0 0.--7. 1. "MIN_REV,Minor revision number for IEE." rgroup.long 0xF8++0x3 line.long 0x0 "AESVID,IEE AES Version ID Register" hexmask.long.byte 0x0 4.--7. 1. "AESVID,AES version ID." hexmask.long.byte 0x0 0.--3. 1. "AESRN,AES revision number." repeat 8. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7)(list ad:0x4006C100 ad:0x4006C200 ad:0x4006C300 ad:0x4006C400 ad:0x4006C500 ad:0x4006C600 ad:0x4006C700 ad:0x4006C800) tree "REGx[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "REGATTR,IEE Region REGION Attribute Register." bitfld.long 0x0 7. "BYP,AES Bypass." "0: use MD field,1: Bypass AES no encrypt/decrypt" bitfld.long 0x0 4.--6. "MD,AES Mode." "0: None (AXI error if accessed),1: XTS,2: CTR w/ address binding,3: CTR w/o address binding,4: CTR keystream only,5: Undefined AXI error if used,6: Undefined AXI error if used,7: Undefined AXI error if used" bitfld.long 0x0 0. "KS,AES key size." "0: 128 bits (CTR) 256 bits (XTS).,1: 256 bits (CTR) 512 bits (XTS)." group.long ($2+0x8)++0x3 line.long 0x0 "REGPO,IEE Region REGION Page Offset Register" hexmask.long.tbyte 0x0 0.--23. 1. "PGOFF,This field represents a 4Kb page offset" repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) wgroup.long ($2+0x40)++0x3 line.long 0x0 "REGKEY1_$1,IEE Region REGION Key 1 Register" hexmask.long 0x0 0.--31. 1. "KEY1,Key 1." repeat.end repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) wgroup.long ($2+0x80)++0x3 line.long 0x0 "REGKEY2_$1,IEE Region REGION Key 2 Register" hexmask.long 0x0 0.--31. 1. "KEY2,Key 2." repeat.end tree.end repeat.end base ad:0x4006C000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0xF00)++0x3 line.long 0x0 "AES_TST_DB[$1],IEE AES Test Mode Data Buffer" hexmask.long 0x0 0.--31. 1. "AES_TST_DB0,AES test mode data buffer." repeat.end tree.end tree.end tree "IOMUXC" base ad:0x0 tree "IOMUXC" base ad:0x400E8000 group.long 0x10++0x48F line.long 0x0 "SW_MUX_CTL_PAD_GPIO_EMC_B1_00,SW_MUX_CTL_PAD_GPIO_EMC_B1_00 SW MUX Control Register" bitfld.long 0x0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_00" hexmask.long.byte 0x0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x4 "SW_MUX_CTL_PAD_GPIO_EMC_B1_01,SW_MUX_CTL_PAD_GPIO_EMC_B1_01 SW MUX Control Register" bitfld.long 0x4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_01" hexmask.long.byte 0x4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x8 "SW_MUX_CTL_PAD_GPIO_EMC_B1_02,SW_MUX_CTL_PAD_GPIO_EMC_B1_02 SW MUX Control Register" bitfld.long 0x8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_02" hexmask.long.byte 0x8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xC "SW_MUX_CTL_PAD_GPIO_EMC_B1_03,SW_MUX_CTL_PAD_GPIO_EMC_B1_03 SW MUX Control Register" bitfld.long 0xC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_03" hexmask.long.byte 0xC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x10 "SW_MUX_CTL_PAD_GPIO_EMC_B1_04,SW_MUX_CTL_PAD_GPIO_EMC_B1_04 SW MUX Control Register" bitfld.long 0x10 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_04" hexmask.long.byte 0x10 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x14 "SW_MUX_CTL_PAD_GPIO_EMC_B1_05,SW_MUX_CTL_PAD_GPIO_EMC_B1_05 SW MUX Control Register" bitfld.long 0x14 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_05" hexmask.long.byte 0x14 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x18 "SW_MUX_CTL_PAD_GPIO_EMC_B1_06,SW_MUX_CTL_PAD_GPIO_EMC_B1_06 SW MUX Control Register" bitfld.long 0x18 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_06" hexmask.long.byte 0x18 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1C "SW_MUX_CTL_PAD_GPIO_EMC_B1_07,SW_MUX_CTL_PAD_GPIO_EMC_B1_07 SW MUX Control Register" bitfld.long 0x1C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_07" hexmask.long.byte 0x1C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x20 "SW_MUX_CTL_PAD_GPIO_EMC_B1_08,SW_MUX_CTL_PAD_GPIO_EMC_B1_08 SW MUX Control Register" bitfld.long 0x20 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_08" hexmask.long.byte 0x20 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x24 "SW_MUX_CTL_PAD_GPIO_EMC_B1_09,SW_MUX_CTL_PAD_GPIO_EMC_B1_09 SW MUX Control Register" bitfld.long 0x24 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_09" hexmask.long.byte 0x24 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x28 "SW_MUX_CTL_PAD_GPIO_EMC_B1_10,SW_MUX_CTL_PAD_GPIO_EMC_B1_10 SW MUX Control Register" bitfld.long 0x28 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_10" hexmask.long.byte 0x28 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x2C "SW_MUX_CTL_PAD_GPIO_EMC_B1_11,SW_MUX_CTL_PAD_GPIO_EMC_B1_11 SW MUX Control Register" bitfld.long 0x2C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_11" hexmask.long.byte 0x2C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x30 "SW_MUX_CTL_PAD_GPIO_EMC_B1_12,SW_MUX_CTL_PAD_GPIO_EMC_B1_12 SW MUX Control Register" bitfld.long 0x30 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_12" hexmask.long.byte 0x30 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x34 "SW_MUX_CTL_PAD_GPIO_EMC_B1_13,SW_MUX_CTL_PAD_GPIO_EMC_B1_13 SW MUX Control Register" bitfld.long 0x34 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_13" hexmask.long.byte 0x34 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x38 "SW_MUX_CTL_PAD_GPIO_EMC_B1_14,SW_MUX_CTL_PAD_GPIO_EMC_B1_14 SW MUX Control Register" bitfld.long 0x38 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_14" hexmask.long.byte 0x38 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x3C "SW_MUX_CTL_PAD_GPIO_EMC_B1_15,SW_MUX_CTL_PAD_GPIO_EMC_B1_15 SW MUX Control Register" bitfld.long 0x3C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_15" hexmask.long.byte 0x3C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x40 "SW_MUX_CTL_PAD_GPIO_EMC_B1_16,SW_MUX_CTL_PAD_GPIO_EMC_B1_16 SW MUX Control Register" bitfld.long 0x40 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_16" hexmask.long.byte 0x40 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x44 "SW_MUX_CTL_PAD_GPIO_EMC_B1_17,SW_MUX_CTL_PAD_GPIO_EMC_B1_17 SW MUX Control Register" bitfld.long 0x44 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_17" hexmask.long.byte 0x44 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x48 "SW_MUX_CTL_PAD_GPIO_EMC_B1_18,SW_MUX_CTL_PAD_GPIO_EMC_B1_18 SW MUX Control Register" bitfld.long 0x48 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_18" hexmask.long.byte 0x48 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x4C "SW_MUX_CTL_PAD_GPIO_EMC_B1_19,SW_MUX_CTL_PAD_GPIO_EMC_B1_19 SW MUX Control Register" bitfld.long 0x4C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_19" hexmask.long.byte 0x4C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x50 "SW_MUX_CTL_PAD_GPIO_EMC_B1_20,SW_MUX_CTL_PAD_GPIO_EMC_B1_20 SW MUX Control Register" bitfld.long 0x50 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_20" hexmask.long.byte 0x50 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x54 "SW_MUX_CTL_PAD_GPIO_EMC_B1_21,SW_MUX_CTL_PAD_GPIO_EMC_B1_21 SW MUX Control Register" bitfld.long 0x54 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_21" hexmask.long.byte 0x54 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x58 "SW_MUX_CTL_PAD_GPIO_EMC_B1_22,SW_MUX_CTL_PAD_GPIO_EMC_B1_22 SW MUX Control Register" bitfld.long 0x58 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_22" hexmask.long.byte 0x58 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x5C "SW_MUX_CTL_PAD_GPIO_EMC_B1_23,SW_MUX_CTL_PAD_GPIO_EMC_B1_23 SW MUX Control Register" bitfld.long 0x5C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_23" hexmask.long.byte 0x5C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x60 "SW_MUX_CTL_PAD_GPIO_EMC_B1_24,SW_MUX_CTL_PAD_GPIO_EMC_B1_24 SW MUX Control Register" bitfld.long 0x60 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_24" hexmask.long.byte 0x60 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x64 "SW_MUX_CTL_PAD_GPIO_EMC_B1_25,SW_MUX_CTL_PAD_GPIO_EMC_B1_25 SW MUX Control Register" bitfld.long 0x64 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_25" hexmask.long.byte 0x64 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x68 "SW_MUX_CTL_PAD_GPIO_EMC_B1_26,SW_MUX_CTL_PAD_GPIO_EMC_B1_26 SW MUX Control Register" bitfld.long 0x68 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_26" hexmask.long.byte 0x68 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x6C "SW_MUX_CTL_PAD_GPIO_EMC_B1_27,SW_MUX_CTL_PAD_GPIO_EMC_B1_27 SW MUX Control Register" bitfld.long 0x6C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_27" hexmask.long.byte 0x6C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x70 "SW_MUX_CTL_PAD_GPIO_EMC_B1_28,SW_MUX_CTL_PAD_GPIO_EMC_B1_28 SW MUX Control Register" bitfld.long 0x70 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_28" hexmask.long.byte 0x70 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x74 "SW_MUX_CTL_PAD_GPIO_EMC_B1_29,SW_MUX_CTL_PAD_GPIO_EMC_B1_29 SW MUX Control Register" bitfld.long 0x74 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_29" hexmask.long.byte 0x74 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x78 "SW_MUX_CTL_PAD_GPIO_EMC_B1_30,SW_MUX_CTL_PAD_GPIO_EMC_B1_30 SW MUX Control Register" bitfld.long 0x78 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_30" hexmask.long.byte 0x78 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x7C "SW_MUX_CTL_PAD_GPIO_EMC_B1_31,SW_MUX_CTL_PAD_GPIO_EMC_B1_31 SW MUX Control Register" bitfld.long 0x7C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_31" hexmask.long.byte 0x7C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x80 "SW_MUX_CTL_PAD_GPIO_EMC_B1_32,SW_MUX_CTL_PAD_GPIO_EMC_B1_32 SW MUX Control Register" bitfld.long 0x80 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_32" hexmask.long.byte 0x80 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x84 "SW_MUX_CTL_PAD_GPIO_EMC_B1_33,SW_MUX_CTL_PAD_GPIO_EMC_B1_33 SW MUX Control Register" bitfld.long 0x84 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_33" hexmask.long.byte 0x84 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x88 "SW_MUX_CTL_PAD_GPIO_EMC_B1_34,SW_MUX_CTL_PAD_GPIO_EMC_B1_34 SW MUX Control Register" bitfld.long 0x88 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_34" hexmask.long.byte 0x88 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x8C "SW_MUX_CTL_PAD_GPIO_EMC_B1_35,SW_MUX_CTL_PAD_GPIO_EMC_B1_35 SW MUX Control Register" bitfld.long 0x8C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_35" hexmask.long.byte 0x8C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x90 "SW_MUX_CTL_PAD_GPIO_EMC_B1_36,SW_MUX_CTL_PAD_GPIO_EMC_B1_36 SW MUX Control Register" bitfld.long 0x90 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_36" hexmask.long.byte 0x90 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x94 "SW_MUX_CTL_PAD_GPIO_EMC_B1_37,SW_MUX_CTL_PAD_GPIO_EMC_B1_37 SW MUX Control Register" bitfld.long 0x94 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_37" hexmask.long.byte 0x94 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x98 "SW_MUX_CTL_PAD_GPIO_EMC_B1_38,SW_MUX_CTL_PAD_GPIO_EMC_B1_38 SW MUX Control Register" bitfld.long 0x98 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_38" hexmask.long.byte 0x98 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x9C "SW_MUX_CTL_PAD_GPIO_EMC_B1_39,SW_MUX_CTL_PAD_GPIO_EMC_B1_39 SW MUX Control Register" bitfld.long 0x9C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_39" hexmask.long.byte 0x9C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xA0 "SW_MUX_CTL_PAD_GPIO_EMC_B1_40,SW_MUX_CTL_PAD_GPIO_EMC_B1_40 SW MUX Control Register" bitfld.long 0xA0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_40" hexmask.long.byte 0xA0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xA4 "SW_MUX_CTL_PAD_GPIO_EMC_B1_41,SW_MUX_CTL_PAD_GPIO_EMC_B1_41 SW MUX Control Register" bitfld.long 0xA4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B1_41" hexmask.long.byte 0xA4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xA8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_00,SW_MUX_CTL_PAD_GPIO_EMC_B2_00 SW MUX Control Register" bitfld.long 0xA8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_00" hexmask.long.byte 0xA8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xAC "SW_MUX_CTL_PAD_GPIO_EMC_B2_01,SW_MUX_CTL_PAD_GPIO_EMC_B2_01 SW MUX Control Register" bitfld.long 0xAC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_01" hexmask.long.byte 0xAC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xB0 "SW_MUX_CTL_PAD_GPIO_EMC_B2_02,SW_MUX_CTL_PAD_GPIO_EMC_B2_02 SW MUX Control Register" bitfld.long 0xB0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_02" hexmask.long.byte 0xB0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xB4 "SW_MUX_CTL_PAD_GPIO_EMC_B2_03,SW_MUX_CTL_PAD_GPIO_EMC_B2_03 SW MUX Control Register" bitfld.long 0xB4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_03" hexmask.long.byte 0xB4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xB8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_04,SW_MUX_CTL_PAD_GPIO_EMC_B2_04 SW MUX Control Register" bitfld.long 0xB8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_04" hexmask.long.byte 0xB8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xBC "SW_MUX_CTL_PAD_GPIO_EMC_B2_05,SW_MUX_CTL_PAD_GPIO_EMC_B2_05 SW MUX Control Register" bitfld.long 0xBC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_05" hexmask.long.byte 0xBC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xC0 "SW_MUX_CTL_PAD_GPIO_EMC_B2_06,SW_MUX_CTL_PAD_GPIO_EMC_B2_06 SW MUX Control Register" bitfld.long 0xC0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_06" hexmask.long.byte 0xC0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xC4 "SW_MUX_CTL_PAD_GPIO_EMC_B2_07,SW_MUX_CTL_PAD_GPIO_EMC_B2_07 SW MUX Control Register" bitfld.long 0xC4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_07" hexmask.long.byte 0xC4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xC8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_08,SW_MUX_CTL_PAD_GPIO_EMC_B2_08 SW MUX Control Register" bitfld.long 0xC8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_08" hexmask.long.byte 0xC8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xCC "SW_MUX_CTL_PAD_GPIO_EMC_B2_09,SW_MUX_CTL_PAD_GPIO_EMC_B2_09 SW MUX Control Register" bitfld.long 0xCC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_09" hexmask.long.byte 0xCC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xD0 "SW_MUX_CTL_PAD_GPIO_EMC_B2_10,SW_MUX_CTL_PAD_GPIO_EMC_B2_10 SW MUX Control Register" bitfld.long 0xD0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_10" hexmask.long.byte 0xD0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xD4 "SW_MUX_CTL_PAD_GPIO_EMC_B2_11,SW_MUX_CTL_PAD_GPIO_EMC_B2_11 SW MUX Control Register" bitfld.long 0xD4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_11" hexmask.long.byte 0xD4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xD8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_12,SW_MUX_CTL_PAD_GPIO_EMC_B2_12 SW MUX Control Register" bitfld.long 0xD8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_12" hexmask.long.byte 0xD8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xDC "SW_MUX_CTL_PAD_GPIO_EMC_B2_13,SW_MUX_CTL_PAD_GPIO_EMC_B2_13 SW MUX Control Register" bitfld.long 0xDC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_13" hexmask.long.byte 0xDC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xE0 "SW_MUX_CTL_PAD_GPIO_EMC_B2_14,SW_MUX_CTL_PAD_GPIO_EMC_B2_14 SW MUX Control Register" bitfld.long 0xE0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_14" hexmask.long.byte 0xE0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xE4 "SW_MUX_CTL_PAD_GPIO_EMC_B2_15,SW_MUX_CTL_PAD_GPIO_EMC_B2_15 SW MUX Control Register" bitfld.long 0xE4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_15" hexmask.long.byte 0xE4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xE8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_16,SW_MUX_CTL_PAD_GPIO_EMC_B2_16 SW MUX Control Register" bitfld.long 0xE8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_16" hexmask.long.byte 0xE8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xEC "SW_MUX_CTL_PAD_GPIO_EMC_B2_17,SW_MUX_CTL_PAD_GPIO_EMC_B2_17 SW MUX Control Register" bitfld.long 0xEC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_17" hexmask.long.byte 0xEC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xF0 "SW_MUX_CTL_PAD_GPIO_EMC_B2_18,SW_MUX_CTL_PAD_GPIO_EMC_B2_18 SW MUX Control Register" bitfld.long 0xF0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_18" hexmask.long.byte 0xF0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xF4 "SW_MUX_CTL_PAD_GPIO_EMC_B2_19,SW_MUX_CTL_PAD_GPIO_EMC_B2_19 SW MUX Control Register" bitfld.long 0xF4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_19" hexmask.long.byte 0xF4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xF8 "SW_MUX_CTL_PAD_GPIO_EMC_B2_20,SW_MUX_CTL_PAD_GPIO_EMC_B2_20 SW MUX Control Register" bitfld.long 0xF8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_EMC_B2_20" hexmask.long.byte 0xF8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xFC "SW_MUX_CTL_PAD_GPIO_AD_00,SW_MUX_CTL_PAD_GPIO_AD_00 SW MUX Control Register" bitfld.long 0xFC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_00" hexmask.long.byte 0xFC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x100 "SW_MUX_CTL_PAD_GPIO_AD_01,SW_MUX_CTL_PAD_GPIO_AD_01 SW MUX Control Register" bitfld.long 0x100 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_01" hexmask.long.byte 0x100 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x104 "SW_MUX_CTL_PAD_GPIO_AD_02,SW_MUX_CTL_PAD_GPIO_AD_02 SW MUX Control Register" bitfld.long 0x104 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_02" hexmask.long.byte 0x104 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x108 "SW_MUX_CTL_PAD_GPIO_AD_03,SW_MUX_CTL_PAD_GPIO_AD_03 SW MUX Control Register" bitfld.long 0x108 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_03" hexmask.long.byte 0x108 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x10C "SW_MUX_CTL_PAD_GPIO_AD_04,SW_MUX_CTL_PAD_GPIO_AD_04 SW MUX Control Register" bitfld.long 0x10C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_04" hexmask.long.byte 0x10C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x110 "SW_MUX_CTL_PAD_GPIO_AD_05,SW_MUX_CTL_PAD_GPIO_AD_05 SW MUX Control Register" bitfld.long 0x110 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_05" hexmask.long.byte 0x110 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x114 "SW_MUX_CTL_PAD_GPIO_AD_06,SW_MUX_CTL_PAD_GPIO_AD_06 SW MUX Control Register" bitfld.long 0x114 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_06" hexmask.long.byte 0x114 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x118 "SW_MUX_CTL_PAD_GPIO_AD_07,SW_MUX_CTL_PAD_GPIO_AD_07 SW MUX Control Register" bitfld.long 0x118 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_07" hexmask.long.byte 0x118 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x11C "SW_MUX_CTL_PAD_GPIO_AD_08,SW_MUX_CTL_PAD_GPIO_AD_08 SW MUX Control Register" bitfld.long 0x11C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_08" hexmask.long.byte 0x11C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x120 "SW_MUX_CTL_PAD_GPIO_AD_09,SW_MUX_CTL_PAD_GPIO_AD_09 SW MUX Control Register" bitfld.long 0x120 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_09" hexmask.long.byte 0x120 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x124 "SW_MUX_CTL_PAD_GPIO_AD_10,SW_MUX_CTL_PAD_GPIO_AD_10 SW MUX Control Register" bitfld.long 0x124 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_10" hexmask.long.byte 0x124 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x128 "SW_MUX_CTL_PAD_GPIO_AD_11,SW_MUX_CTL_PAD_GPIO_AD_11 SW MUX Control Register" bitfld.long 0x128 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_11" hexmask.long.byte 0x128 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x12C "SW_MUX_CTL_PAD_GPIO_AD_12,SW_MUX_CTL_PAD_GPIO_AD_12 SW MUX Control Register" bitfld.long 0x12C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_12" hexmask.long.byte 0x12C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x130 "SW_MUX_CTL_PAD_GPIO_AD_13,SW_MUX_CTL_PAD_GPIO_AD_13 SW MUX Control Register" bitfld.long 0x130 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_13" hexmask.long.byte 0x130 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x134 "SW_MUX_CTL_PAD_GPIO_AD_14,SW_MUX_CTL_PAD_GPIO_AD_14 SW MUX Control Register" bitfld.long 0x134 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_14" hexmask.long.byte 0x134 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x138 "SW_MUX_CTL_PAD_GPIO_AD_15,SW_MUX_CTL_PAD_GPIO_AD_15 SW MUX Control Register" bitfld.long 0x138 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_15" hexmask.long.byte 0x138 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x13C "SW_MUX_CTL_PAD_GPIO_AD_16,SW_MUX_CTL_PAD_GPIO_AD_16 SW MUX Control Register" bitfld.long 0x13C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_16" hexmask.long.byte 0x13C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x140 "SW_MUX_CTL_PAD_GPIO_AD_17,SW_MUX_CTL_PAD_GPIO_AD_17 SW MUX Control Register" bitfld.long 0x140 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_17" hexmask.long.byte 0x140 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x144 "SW_MUX_CTL_PAD_GPIO_AD_18,SW_MUX_CTL_PAD_GPIO_AD_18 SW MUX Control Register" bitfld.long 0x144 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_18" hexmask.long.byte 0x144 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x148 "SW_MUX_CTL_PAD_GPIO_AD_19,SW_MUX_CTL_PAD_GPIO_AD_19 SW MUX Control Register" bitfld.long 0x148 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_19" hexmask.long.byte 0x148 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x14C "SW_MUX_CTL_PAD_GPIO_AD_20,SW_MUX_CTL_PAD_GPIO_AD_20 SW MUX Control Register" bitfld.long 0x14C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_20" hexmask.long.byte 0x14C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x150 "SW_MUX_CTL_PAD_GPIO_AD_21,SW_MUX_CTL_PAD_GPIO_AD_21 SW MUX Control Register" bitfld.long 0x150 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_21" hexmask.long.byte 0x150 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x154 "SW_MUX_CTL_PAD_GPIO_AD_22,SW_MUX_CTL_PAD_GPIO_AD_22 SW MUX Control Register" bitfld.long 0x154 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_22" hexmask.long.byte 0x154 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x158 "SW_MUX_CTL_PAD_GPIO_AD_23,SW_MUX_CTL_PAD_GPIO_AD_23 SW MUX Control Register" bitfld.long 0x158 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_23" hexmask.long.byte 0x158 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x15C "SW_MUX_CTL_PAD_GPIO_AD_24,SW_MUX_CTL_PAD_GPIO_AD_24 SW MUX Control Register" bitfld.long 0x15C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_24" hexmask.long.byte 0x15C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x160 "SW_MUX_CTL_PAD_GPIO_AD_25,SW_MUX_CTL_PAD_GPIO_AD_25 SW MUX Control Register" bitfld.long 0x160 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_25" hexmask.long.byte 0x160 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x164 "SW_MUX_CTL_PAD_GPIO_AD_26,SW_MUX_CTL_PAD_GPIO_AD_26 SW MUX Control Register" bitfld.long 0x164 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_26" hexmask.long.byte 0x164 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x168 "SW_MUX_CTL_PAD_GPIO_AD_27,SW_MUX_CTL_PAD_GPIO_AD_27 SW MUX Control Register" bitfld.long 0x168 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_27" hexmask.long.byte 0x168 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x16C "SW_MUX_CTL_PAD_GPIO_AD_28,SW_MUX_CTL_PAD_GPIO_AD_28 SW MUX Control Register" bitfld.long 0x16C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_28" hexmask.long.byte 0x16C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x170 "SW_MUX_CTL_PAD_GPIO_AD_29,SW_MUX_CTL_PAD_GPIO_AD_29 SW MUX Control Register" bitfld.long 0x170 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_29" hexmask.long.byte 0x170 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x174 "SW_MUX_CTL_PAD_GPIO_AD_30,SW_MUX_CTL_PAD_GPIO_AD_30 SW MUX Control Register" bitfld.long 0x174 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_30" hexmask.long.byte 0x174 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x178 "SW_MUX_CTL_PAD_GPIO_AD_31,SW_MUX_CTL_PAD_GPIO_AD_31 SW MUX Control Register" bitfld.long 0x178 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_31" hexmask.long.byte 0x178 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x17C "SW_MUX_CTL_PAD_GPIO_AD_32,SW_MUX_CTL_PAD_GPIO_AD_32 SW MUX Control Register" bitfld.long 0x17C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_32" hexmask.long.byte 0x17C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x180 "SW_MUX_CTL_PAD_GPIO_AD_33,SW_MUX_CTL_PAD_GPIO_AD_33 SW MUX Control Register" bitfld.long 0x180 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_33" hexmask.long.byte 0x180 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x184 "SW_MUX_CTL_PAD_GPIO_AD_34,SW_MUX_CTL_PAD_GPIO_AD_34 SW MUX Control Register" bitfld.long 0x184 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_34" hexmask.long.byte 0x184 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x188 "SW_MUX_CTL_PAD_GPIO_AD_35,SW_MUX_CTL_PAD_GPIO_AD_35 SW MUX Control Register" bitfld.long 0x188 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_AD_35" hexmask.long.byte 0x188 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x18C "SW_MUX_CTL_PAD_GPIO_SD_B1_00,SW_MUX_CTL_PAD_GPIO_SD_B1_00 SW MUX Control Register" bitfld.long 0x18C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_00" hexmask.long.byte 0x18C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x190 "SW_MUX_CTL_PAD_GPIO_SD_B1_01,SW_MUX_CTL_PAD_GPIO_SD_B1_01 SW MUX Control Register" bitfld.long 0x190 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_01" hexmask.long.byte 0x190 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x194 "SW_MUX_CTL_PAD_GPIO_SD_B1_02,SW_MUX_CTL_PAD_GPIO_SD_B1_02 SW MUX Control Register" bitfld.long 0x194 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_02" hexmask.long.byte 0x194 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x198 "SW_MUX_CTL_PAD_GPIO_SD_B1_03,SW_MUX_CTL_PAD_GPIO_SD_B1_03 SW MUX Control Register" bitfld.long 0x198 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_03" hexmask.long.byte 0x198 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x19C "SW_MUX_CTL_PAD_GPIO_SD_B1_04,SW_MUX_CTL_PAD_GPIO_SD_B1_04 SW MUX Control Register" bitfld.long 0x19C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_04" hexmask.long.byte 0x19C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1A0 "SW_MUX_CTL_PAD_GPIO_SD_B1_05,SW_MUX_CTL_PAD_GPIO_SD_B1_05 SW MUX Control Register" bitfld.long 0x1A0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B1_05" hexmask.long.byte 0x1A0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1A4 "SW_MUX_CTL_PAD_GPIO_SD_B2_00,SW_MUX_CTL_PAD_GPIO_SD_B2_00 SW MUX Control Register" bitfld.long 0x1A4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_00" hexmask.long.byte 0x1A4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1A8 "SW_MUX_CTL_PAD_GPIO_SD_B2_01,SW_MUX_CTL_PAD_GPIO_SD_B2_01 SW MUX Control Register" bitfld.long 0x1A8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_01" hexmask.long.byte 0x1A8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1AC "SW_MUX_CTL_PAD_GPIO_SD_B2_02,SW_MUX_CTL_PAD_GPIO_SD_B2_02 SW MUX Control Register" bitfld.long 0x1AC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_02" hexmask.long.byte 0x1AC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1B0 "SW_MUX_CTL_PAD_GPIO_SD_B2_03,SW_MUX_CTL_PAD_GPIO_SD_B2_03 SW MUX Control Register" bitfld.long 0x1B0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_03" hexmask.long.byte 0x1B0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1B4 "SW_MUX_CTL_PAD_GPIO_SD_B2_04,SW_MUX_CTL_PAD_GPIO_SD_B2_04 SW MUX Control Register" bitfld.long 0x1B4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_04" hexmask.long.byte 0x1B4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1B8 "SW_MUX_CTL_PAD_GPIO_SD_B2_05,SW_MUX_CTL_PAD_GPIO_SD_B2_05 SW MUX Control Register" bitfld.long 0x1B8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_05" hexmask.long.byte 0x1B8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1BC "SW_MUX_CTL_PAD_GPIO_SD_B2_06,SW_MUX_CTL_PAD_GPIO_SD_B2_06 SW MUX Control Register" bitfld.long 0x1BC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_06" hexmask.long.byte 0x1BC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1C0 "SW_MUX_CTL_PAD_GPIO_SD_B2_07,SW_MUX_CTL_PAD_GPIO_SD_B2_07 SW MUX Control Register" bitfld.long 0x1C0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_07" hexmask.long.byte 0x1C0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1C4 "SW_MUX_CTL_PAD_GPIO_SD_B2_08,SW_MUX_CTL_PAD_GPIO_SD_B2_08 SW MUX Control Register" bitfld.long 0x1C4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_08" hexmask.long.byte 0x1C4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1C8 "SW_MUX_CTL_PAD_GPIO_SD_B2_09,SW_MUX_CTL_PAD_GPIO_SD_B2_09 SW MUX Control Register" bitfld.long 0x1C8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_09" hexmask.long.byte 0x1C8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1CC "SW_MUX_CTL_PAD_GPIO_SD_B2_10,SW_MUX_CTL_PAD_GPIO_SD_B2_10 SW MUX Control Register" bitfld.long 0x1CC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_10" hexmask.long.byte 0x1CC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1D0 "SW_MUX_CTL_PAD_GPIO_SD_B2_11,SW_MUX_CTL_PAD_GPIO_SD_B2_11 SW MUX Control Register" bitfld.long 0x1D0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SD_B2_11" hexmask.long.byte 0x1D0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1D4 "SW_MUX_CTL_PAD_GPIO_DISP_B1_00,SW_MUX_CTL_PAD_GPIO_DISP_B1_00 SW MUX Control Register" bitfld.long 0x1D4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_00" hexmask.long.byte 0x1D4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1D8 "SW_MUX_CTL_PAD_GPIO_DISP_B1_01,SW_MUX_CTL_PAD_GPIO_DISP_B1_01 SW MUX Control Register" bitfld.long 0x1D8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_01" hexmask.long.byte 0x1D8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1DC "SW_MUX_CTL_PAD_GPIO_DISP_B1_02,SW_MUX_CTL_PAD_GPIO_DISP_B1_02 SW MUX Control Register" bitfld.long 0x1DC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_02" hexmask.long.byte 0x1DC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1E0 "SW_MUX_CTL_PAD_GPIO_DISP_B1_03,SW_MUX_CTL_PAD_GPIO_DISP_B1_03 SW MUX Control Register" bitfld.long 0x1E0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_03" hexmask.long.byte 0x1E0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1E4 "SW_MUX_CTL_PAD_GPIO_DISP_B1_04,SW_MUX_CTL_PAD_GPIO_DISP_B1_04 SW MUX Control Register" bitfld.long 0x1E4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_04" hexmask.long.byte 0x1E4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1E8 "SW_MUX_CTL_PAD_GPIO_DISP_B1_05,SW_MUX_CTL_PAD_GPIO_DISP_B1_05 SW MUX Control Register" bitfld.long 0x1E8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_05" hexmask.long.byte 0x1E8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1EC "SW_MUX_CTL_PAD_GPIO_DISP_B1_06,SW_MUX_CTL_PAD_GPIO_DISP_B1_06 SW MUX Control Register" bitfld.long 0x1EC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_06" hexmask.long.byte 0x1EC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1F0 "SW_MUX_CTL_PAD_GPIO_DISP_B1_07,SW_MUX_CTL_PAD_GPIO_DISP_B1_07 SW MUX Control Register" bitfld.long 0x1F0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_07" hexmask.long.byte 0x1F0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1F4 "SW_MUX_CTL_PAD_GPIO_DISP_B1_08,SW_MUX_CTL_PAD_GPIO_DISP_B1_08 SW MUX Control Register" bitfld.long 0x1F4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_08" hexmask.long.byte 0x1F4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1F8 "SW_MUX_CTL_PAD_GPIO_DISP_B1_09,SW_MUX_CTL_PAD_GPIO_DISP_B1_09 SW MUX Control Register" bitfld.long 0x1F8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_09" hexmask.long.byte 0x1F8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1FC "SW_MUX_CTL_PAD_GPIO_DISP_B1_10,SW_MUX_CTL_PAD_GPIO_DISP_B1_10 SW MUX Control Register" bitfld.long 0x1FC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_10" hexmask.long.byte 0x1FC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x200 "SW_MUX_CTL_PAD_GPIO_DISP_B1_11,SW_MUX_CTL_PAD_GPIO_DISP_B1_11 SW MUX Control Register" bitfld.long 0x200 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B1_11" hexmask.long.byte 0x200 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x204 "SW_MUX_CTL_PAD_GPIO_DISP_B2_00,SW_MUX_CTL_PAD_GPIO_DISP_B2_00 SW MUX Control Register" bitfld.long 0x204 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_00" hexmask.long.byte 0x204 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x208 "SW_MUX_CTL_PAD_GPIO_DISP_B2_01,SW_MUX_CTL_PAD_GPIO_DISP_B2_01 SW MUX Control Register" bitfld.long 0x208 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_01" hexmask.long.byte 0x208 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x20C "SW_MUX_CTL_PAD_GPIO_DISP_B2_02,SW_MUX_CTL_PAD_GPIO_DISP_B2_02 SW MUX Control Register" bitfld.long 0x20C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_02" hexmask.long.byte 0x20C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x210 "SW_MUX_CTL_PAD_GPIO_DISP_B2_03,SW_MUX_CTL_PAD_GPIO_DISP_B2_03 SW MUX Control Register" bitfld.long 0x210 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_03" hexmask.long.byte 0x210 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x214 "SW_MUX_CTL_PAD_GPIO_DISP_B2_04,SW_MUX_CTL_PAD_GPIO_DISP_B2_04 SW MUX Control Register" bitfld.long 0x214 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_04" hexmask.long.byte 0x214 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x218 "SW_MUX_CTL_PAD_GPIO_DISP_B2_05,SW_MUX_CTL_PAD_GPIO_DISP_B2_05 SW MUX Control Register" bitfld.long 0x218 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_05" hexmask.long.byte 0x218 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x21C "SW_MUX_CTL_PAD_GPIO_DISP_B2_06,SW_MUX_CTL_PAD_GPIO_DISP_B2_06 SW MUX Control Register" bitfld.long 0x21C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_06" hexmask.long.byte 0x21C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x220 "SW_MUX_CTL_PAD_GPIO_DISP_B2_07,SW_MUX_CTL_PAD_GPIO_DISP_B2_07 SW MUX Control Register" bitfld.long 0x220 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_07" hexmask.long.byte 0x220 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x224 "SW_MUX_CTL_PAD_GPIO_DISP_B2_08,SW_MUX_CTL_PAD_GPIO_DISP_B2_08 SW MUX Control Register" bitfld.long 0x224 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_08" hexmask.long.byte 0x224 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x228 "SW_MUX_CTL_PAD_GPIO_DISP_B2_09,SW_MUX_CTL_PAD_GPIO_DISP_B2_09 SW MUX Control Register" bitfld.long 0x228 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_09" hexmask.long.byte 0x228 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x22C "SW_MUX_CTL_PAD_GPIO_DISP_B2_10,SW_MUX_CTL_PAD_GPIO_DISP_B2_10 SW MUX Control Register" bitfld.long 0x22C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_10" hexmask.long.byte 0x22C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x230 "SW_MUX_CTL_PAD_GPIO_DISP_B2_11,SW_MUX_CTL_PAD_GPIO_DISP_B2_11 SW MUX Control Register" bitfld.long 0x230 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_11" hexmask.long.byte 0x230 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x234 "SW_MUX_CTL_PAD_GPIO_DISP_B2_12,SW_MUX_CTL_PAD_GPIO_DISP_B2_12 SW MUX Control Register" bitfld.long 0x234 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_12" hexmask.long.byte 0x234 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x238 "SW_MUX_CTL_PAD_GPIO_DISP_B2_13,SW_MUX_CTL_PAD_GPIO_DISP_B2_13 SW MUX Control Register" bitfld.long 0x238 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_13" hexmask.long.byte 0x238 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x23C "SW_MUX_CTL_PAD_GPIO_DISP_B2_14,SW_MUX_CTL_PAD_GPIO_DISP_B2_14 SW MUX Control Register" bitfld.long 0x23C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_14" hexmask.long.byte 0x23C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x240 "SW_MUX_CTL_PAD_GPIO_DISP_B2_15,SW_MUX_CTL_PAD_GPIO_DISP_B2_15 SW MUX Control Register" bitfld.long 0x240 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_DISP_B2_15" hexmask.long.byte 0x240 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x244 "SW_PAD_CTL_PAD_GPIO_EMC_B1_00,SW_PAD_CTL_PAD_GPIO_EMC_B1_00 SW PAD Control Register" bitfld.long 0x244 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x244 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x244 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x244 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x244 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x248 "SW_PAD_CTL_PAD_GPIO_EMC_B1_01,SW_PAD_CTL_PAD_GPIO_EMC_B1_01 SW PAD Control Register" bitfld.long 0x248 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x248 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x248 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x248 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x248 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x24C "SW_PAD_CTL_PAD_GPIO_EMC_B1_02,SW_PAD_CTL_PAD_GPIO_EMC_B1_02 SW PAD Control Register" bitfld.long 0x24C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x24C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x24C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x24C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x24C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x250 "SW_PAD_CTL_PAD_GPIO_EMC_B1_03,SW_PAD_CTL_PAD_GPIO_EMC_B1_03 SW PAD Control Register" bitfld.long 0x250 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x250 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x250 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x250 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x250 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x254 "SW_PAD_CTL_PAD_GPIO_EMC_B1_04,SW_PAD_CTL_PAD_GPIO_EMC_B1_04 SW PAD Control Register" bitfld.long 0x254 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x254 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x254 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x254 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x254 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x258 "SW_PAD_CTL_PAD_GPIO_EMC_B1_05,SW_PAD_CTL_PAD_GPIO_EMC_B1_05 SW PAD Control Register" bitfld.long 0x258 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x258 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x258 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x258 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x258 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x25C "SW_PAD_CTL_PAD_GPIO_EMC_B1_06,SW_PAD_CTL_PAD_GPIO_EMC_B1_06 SW PAD Control Register" bitfld.long 0x25C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x25C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x25C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x25C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x25C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x260 "SW_PAD_CTL_PAD_GPIO_EMC_B1_07,SW_PAD_CTL_PAD_GPIO_EMC_B1_07 SW PAD Control Register" bitfld.long 0x260 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x260 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x260 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x260 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x260 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x264 "SW_PAD_CTL_PAD_GPIO_EMC_B1_08,SW_PAD_CTL_PAD_GPIO_EMC_B1_08 SW PAD Control Register" bitfld.long 0x264 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x264 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x264 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x264 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x264 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x268 "SW_PAD_CTL_PAD_GPIO_EMC_B1_09,SW_PAD_CTL_PAD_GPIO_EMC_B1_09 SW PAD Control Register" bitfld.long 0x268 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x268 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x268 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x268 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x268 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x26C "SW_PAD_CTL_PAD_GPIO_EMC_B1_10,SW_PAD_CTL_PAD_GPIO_EMC_B1_10 SW PAD Control Register" bitfld.long 0x26C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x26C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x26C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x26C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x26C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x270 "SW_PAD_CTL_PAD_GPIO_EMC_B1_11,SW_PAD_CTL_PAD_GPIO_EMC_B1_11 SW PAD Control Register" bitfld.long 0x270 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x270 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x270 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x270 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x270 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x274 "SW_PAD_CTL_PAD_GPIO_EMC_B1_12,SW_PAD_CTL_PAD_GPIO_EMC_B1_12 SW PAD Control Register" bitfld.long 0x274 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x274 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x274 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x274 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x274 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x278 "SW_PAD_CTL_PAD_GPIO_EMC_B1_13,SW_PAD_CTL_PAD_GPIO_EMC_B1_13 SW PAD Control Register" bitfld.long 0x278 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x278 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x278 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x278 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x278 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x27C "SW_PAD_CTL_PAD_GPIO_EMC_B1_14,SW_PAD_CTL_PAD_GPIO_EMC_B1_14 SW PAD Control Register" bitfld.long 0x27C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x27C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x27C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x27C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x27C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x280 "SW_PAD_CTL_PAD_GPIO_EMC_B1_15,SW_PAD_CTL_PAD_GPIO_EMC_B1_15 SW PAD Control Register" bitfld.long 0x280 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x280 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x280 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x280 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x280 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x284 "SW_PAD_CTL_PAD_GPIO_EMC_B1_16,SW_PAD_CTL_PAD_GPIO_EMC_B1_16 SW PAD Control Register" bitfld.long 0x284 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x284 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x284 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x284 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x284 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x288 "SW_PAD_CTL_PAD_GPIO_EMC_B1_17,SW_PAD_CTL_PAD_GPIO_EMC_B1_17 SW PAD Control Register" bitfld.long 0x288 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x288 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x288 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x288 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x288 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x28C "SW_PAD_CTL_PAD_GPIO_EMC_B1_18,SW_PAD_CTL_PAD_GPIO_EMC_B1_18 SW PAD Control Register" bitfld.long 0x28C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x28C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x28C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x28C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x28C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x290 "SW_PAD_CTL_PAD_GPIO_EMC_B1_19,SW_PAD_CTL_PAD_GPIO_EMC_B1_19 SW PAD Control Register" bitfld.long 0x290 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x290 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x290 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x290 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x290 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x294 "SW_PAD_CTL_PAD_GPIO_EMC_B1_20,SW_PAD_CTL_PAD_GPIO_EMC_B1_20 SW PAD Control Register" bitfld.long 0x294 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x294 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x294 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x294 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x294 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x298 "SW_PAD_CTL_PAD_GPIO_EMC_B1_21,SW_PAD_CTL_PAD_GPIO_EMC_B1_21 SW PAD Control Register" bitfld.long 0x298 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x298 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x298 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x298 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x298 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x29C "SW_PAD_CTL_PAD_GPIO_EMC_B1_22,SW_PAD_CTL_PAD_GPIO_EMC_B1_22 SW PAD Control Register" bitfld.long 0x29C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x29C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x29C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x29C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x29C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2A0 "SW_PAD_CTL_PAD_GPIO_EMC_B1_23,SW_PAD_CTL_PAD_GPIO_EMC_B1_23 SW PAD Control Register" bitfld.long 0x2A0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2A0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2A0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2A0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2A0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2A4 "SW_PAD_CTL_PAD_GPIO_EMC_B1_24,SW_PAD_CTL_PAD_GPIO_EMC_B1_24 SW PAD Control Register" bitfld.long 0x2A4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2A4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2A4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2A4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2A4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2A8 "SW_PAD_CTL_PAD_GPIO_EMC_B1_25,SW_PAD_CTL_PAD_GPIO_EMC_B1_25 SW PAD Control Register" bitfld.long 0x2A8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2A8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2A8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2A8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2A8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2AC "SW_PAD_CTL_PAD_GPIO_EMC_B1_26,SW_PAD_CTL_PAD_GPIO_EMC_B1_26 SW PAD Control Register" bitfld.long 0x2AC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2AC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2AC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2AC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2AC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2B0 "SW_PAD_CTL_PAD_GPIO_EMC_B1_27,SW_PAD_CTL_PAD_GPIO_EMC_B1_27 SW PAD Control Register" bitfld.long 0x2B0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2B0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2B0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2B0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2B0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2B4 "SW_PAD_CTL_PAD_GPIO_EMC_B1_28,SW_PAD_CTL_PAD_GPIO_EMC_B1_28 SW PAD Control Register" bitfld.long 0x2B4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2B4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2B4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2B4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2B4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2B8 "SW_PAD_CTL_PAD_GPIO_EMC_B1_29,SW_PAD_CTL_PAD_GPIO_EMC_B1_29 SW PAD Control Register" bitfld.long 0x2B8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2B8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2B8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2B8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2B8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2BC "SW_PAD_CTL_PAD_GPIO_EMC_B1_30,SW_PAD_CTL_PAD_GPIO_EMC_B1_30 SW PAD Control Register" bitfld.long 0x2BC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2BC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2BC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2BC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2BC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2C0 "SW_PAD_CTL_PAD_GPIO_EMC_B1_31,SW_PAD_CTL_PAD_GPIO_EMC_B1_31 SW PAD Control Register" bitfld.long 0x2C0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2C0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2C0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2C0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2C0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2C4 "SW_PAD_CTL_PAD_GPIO_EMC_B1_32,SW_PAD_CTL_PAD_GPIO_EMC_B1_32 SW PAD Control Register" bitfld.long 0x2C4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2C4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2C4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2C4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2C4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2C8 "SW_PAD_CTL_PAD_GPIO_EMC_B1_33,SW_PAD_CTL_PAD_GPIO_EMC_B1_33 SW PAD Control Register" bitfld.long 0x2C8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2C8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2C8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2C8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2C8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2CC "SW_PAD_CTL_PAD_GPIO_EMC_B1_34,SW_PAD_CTL_PAD_GPIO_EMC_B1_34 SW PAD Control Register" bitfld.long 0x2CC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2CC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2CC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2CC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2CC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2D0 "SW_PAD_CTL_PAD_GPIO_EMC_B1_35,SW_PAD_CTL_PAD_GPIO_EMC_B1_35 SW PAD Control Register" bitfld.long 0x2D0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2D0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2D0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2D0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2D0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2D4 "SW_PAD_CTL_PAD_GPIO_EMC_B1_36,SW_PAD_CTL_PAD_GPIO_EMC_B1_36 SW PAD Control Register" bitfld.long 0x2D4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2D4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2D4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2D4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2D4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2D8 "SW_PAD_CTL_PAD_GPIO_EMC_B1_37,SW_PAD_CTL_PAD_GPIO_EMC_B1_37 SW PAD Control Register" bitfld.long 0x2D8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2D8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2D8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2D8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2D8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2DC "SW_PAD_CTL_PAD_GPIO_EMC_B1_38,SW_PAD_CTL_PAD_GPIO_EMC_B1_38 SW PAD Control Register" bitfld.long 0x2DC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2DC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2DC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2DC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2DC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2E0 "SW_PAD_CTL_PAD_GPIO_EMC_B1_39,SW_PAD_CTL_PAD_GPIO_EMC_B1_39 SW PAD Control Register" bitfld.long 0x2E0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2E0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2E0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2E0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2E0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2E4 "SW_PAD_CTL_PAD_GPIO_EMC_B1_40,SW_PAD_CTL_PAD_GPIO_EMC_B1_40 SW PAD Control Register" bitfld.long 0x2E4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2E4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2E4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2E4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2E4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2E8 "SW_PAD_CTL_PAD_GPIO_EMC_B1_41,SW_PAD_CTL_PAD_GPIO_EMC_B1_41 SW PAD Control Register" bitfld.long 0x2E8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2E8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2E8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2E8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2E8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2EC "SW_PAD_CTL_PAD_GPIO_EMC_B2_00,SW_PAD_CTL_PAD_GPIO_EMC_B2_00 SW PAD Control Register" bitfld.long 0x2EC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2EC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2EC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2EC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2EC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2F0 "SW_PAD_CTL_PAD_GPIO_EMC_B2_01,SW_PAD_CTL_PAD_GPIO_EMC_B2_01 SW PAD Control Register" bitfld.long 0x2F0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2F0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2F0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2F0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2F0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2F4 "SW_PAD_CTL_PAD_GPIO_EMC_B2_02,SW_PAD_CTL_PAD_GPIO_EMC_B2_02 SW PAD Control Register" bitfld.long 0x2F4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2F4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2F4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2F4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2F4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2F8 "SW_PAD_CTL_PAD_GPIO_EMC_B2_03,SW_PAD_CTL_PAD_GPIO_EMC_B2_03 SW PAD Control Register" bitfld.long 0x2F8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2F8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2F8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2F8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2F8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x2FC "SW_PAD_CTL_PAD_GPIO_EMC_B2_04,SW_PAD_CTL_PAD_GPIO_EMC_B2_04 SW PAD Control Register" bitfld.long 0x2FC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x2FC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2FC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x2FC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x2FC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x300 "SW_PAD_CTL_PAD_GPIO_EMC_B2_05,SW_PAD_CTL_PAD_GPIO_EMC_B2_05 SW PAD Control Register" bitfld.long 0x300 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x300 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x300 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x300 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x300 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x304 "SW_PAD_CTL_PAD_GPIO_EMC_B2_06,SW_PAD_CTL_PAD_GPIO_EMC_B2_06 SW PAD Control Register" bitfld.long 0x304 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x304 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x304 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x304 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x304 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x308 "SW_PAD_CTL_PAD_GPIO_EMC_B2_07,SW_PAD_CTL_PAD_GPIO_EMC_B2_07 SW PAD Control Register" bitfld.long 0x308 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x308 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x308 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x308 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x308 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x30C "SW_PAD_CTL_PAD_GPIO_EMC_B2_08,SW_PAD_CTL_PAD_GPIO_EMC_B2_08 SW PAD Control Register" bitfld.long 0x30C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x30C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x30C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x30C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x30C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x310 "SW_PAD_CTL_PAD_GPIO_EMC_B2_09,SW_PAD_CTL_PAD_GPIO_EMC_B2_09 SW PAD Control Register" bitfld.long 0x310 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x310 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x310 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x310 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x310 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x314 "SW_PAD_CTL_PAD_GPIO_EMC_B2_10,SW_PAD_CTL_PAD_GPIO_EMC_B2_10 SW PAD Control Register" bitfld.long 0x314 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x314 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x314 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x314 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x314 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x318 "SW_PAD_CTL_PAD_GPIO_EMC_B2_11,SW_PAD_CTL_PAD_GPIO_EMC_B2_11 SW PAD Control Register" bitfld.long 0x318 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x318 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x318 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x318 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x318 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x31C "SW_PAD_CTL_PAD_GPIO_EMC_B2_12,SW_PAD_CTL_PAD_GPIO_EMC_B2_12 SW PAD Control Register" bitfld.long 0x31C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x31C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x31C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x31C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x31C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x320 "SW_PAD_CTL_PAD_GPIO_EMC_B2_13,SW_PAD_CTL_PAD_GPIO_EMC_B2_13 SW PAD Control Register" bitfld.long 0x320 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x320 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x320 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x320 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x320 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x324 "SW_PAD_CTL_PAD_GPIO_EMC_B2_14,SW_PAD_CTL_PAD_GPIO_EMC_B2_14 SW PAD Control Register" bitfld.long 0x324 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x324 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x324 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x324 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x324 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x328 "SW_PAD_CTL_PAD_GPIO_EMC_B2_15,SW_PAD_CTL_PAD_GPIO_EMC_B2_15 SW PAD Control Register" bitfld.long 0x328 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x328 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x328 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x328 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x328 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x32C "SW_PAD_CTL_PAD_GPIO_EMC_B2_16,SW_PAD_CTL_PAD_GPIO_EMC_B2_16 SW PAD Control Register" bitfld.long 0x32C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x32C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x32C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x32C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x32C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x330 "SW_PAD_CTL_PAD_GPIO_EMC_B2_17,SW_PAD_CTL_PAD_GPIO_EMC_B2_17 SW PAD Control Register" bitfld.long 0x330 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x330 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x330 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x330 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x330 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x334 "SW_PAD_CTL_PAD_GPIO_EMC_B2_18,SW_PAD_CTL_PAD_GPIO_EMC_B2_18 SW PAD Control Register" bitfld.long 0x334 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x334 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x334 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x334 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x334 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x338 "SW_PAD_CTL_PAD_GPIO_EMC_B2_19,SW_PAD_CTL_PAD_GPIO_EMC_B2_19 SW PAD Control Register" bitfld.long 0x338 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x338 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x338 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x338 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x338 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x33C "SW_PAD_CTL_PAD_GPIO_EMC_B2_20,SW_PAD_CTL_PAD_GPIO_EMC_B2_20 SW PAD Control Register" bitfld.long 0x33C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x33C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x33C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x33C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x33C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x340 "SW_PAD_CTL_PAD_GPIO_AD_00,SW_PAD_CTL_PAD_GPIO_AD_00 SW PAD Control Register" bitfld.long 0x340 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x340 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x340 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x340 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x340 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x340 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x340 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x344 "SW_PAD_CTL_PAD_GPIO_AD_01,SW_PAD_CTL_PAD_GPIO_AD_01 SW PAD Control Register" bitfld.long 0x344 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x344 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x344 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x344 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x344 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x344 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x344 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x348 "SW_PAD_CTL_PAD_GPIO_AD_02,SW_PAD_CTL_PAD_GPIO_AD_02 SW PAD Control Register" bitfld.long 0x348 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x348 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x348 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x348 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x348 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x348 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x348 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x34C "SW_PAD_CTL_PAD_GPIO_AD_03,SW_PAD_CTL_PAD_GPIO_AD_03 SW PAD Control Register" bitfld.long 0x34C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x34C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x34C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x34C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x34C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x34C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x34C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x350 "SW_PAD_CTL_PAD_GPIO_AD_04,SW_PAD_CTL_PAD_GPIO_AD_04 SW PAD Control Register" bitfld.long 0x350 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x350 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x350 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x350 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x350 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x350 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x350 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x354 "SW_PAD_CTL_PAD_GPIO_AD_05,SW_PAD_CTL_PAD_GPIO_AD_05 SW PAD Control Register" bitfld.long 0x354 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x354 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x354 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x354 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x354 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x354 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x354 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x358 "SW_PAD_CTL_PAD_GPIO_AD_06,SW_PAD_CTL_PAD_GPIO_AD_06 SW PAD Control Register" bitfld.long 0x358 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x358 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x358 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x358 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x358 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x358 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x358 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x35C "SW_PAD_CTL_PAD_GPIO_AD_07,SW_PAD_CTL_PAD_GPIO_AD_07 SW PAD Control Register" bitfld.long 0x35C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x35C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x35C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x35C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x35C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x35C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x35C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x360 "SW_PAD_CTL_PAD_GPIO_AD_08,SW_PAD_CTL_PAD_GPIO_AD_08 SW PAD Control Register" bitfld.long 0x360 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x360 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x360 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x360 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x360 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x360 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x360 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x364 "SW_PAD_CTL_PAD_GPIO_AD_09,SW_PAD_CTL_PAD_GPIO_AD_09 SW PAD Control Register" bitfld.long 0x364 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x364 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x364 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x364 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x364 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x364 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x364 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x368 "SW_PAD_CTL_PAD_GPIO_AD_10,SW_PAD_CTL_PAD_GPIO_AD_10 SW PAD Control Register" bitfld.long 0x368 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x368 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x368 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x368 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x368 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x368 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x368 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x36C "SW_PAD_CTL_PAD_GPIO_AD_11,SW_PAD_CTL_PAD_GPIO_AD_11 SW PAD Control Register" bitfld.long 0x36C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x36C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x36C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x36C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x36C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x36C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x36C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x370 "SW_PAD_CTL_PAD_GPIO_AD_12,SW_PAD_CTL_PAD_GPIO_AD_12 SW PAD Control Register" bitfld.long 0x370 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x370 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x370 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x370 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x370 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x370 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x370 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x374 "SW_PAD_CTL_PAD_GPIO_AD_13,SW_PAD_CTL_PAD_GPIO_AD_13 SW PAD Control Register" bitfld.long 0x374 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x374 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x374 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x374 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x374 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x374 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x374 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x378 "SW_PAD_CTL_PAD_GPIO_AD_14,SW_PAD_CTL_PAD_GPIO_AD_14 SW PAD Control Register" bitfld.long 0x378 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x378 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x378 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x378 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x378 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x378 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x378 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x37C "SW_PAD_CTL_PAD_GPIO_AD_15,SW_PAD_CTL_PAD_GPIO_AD_15 SW PAD Control Register" bitfld.long 0x37C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x37C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x37C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x37C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x37C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x37C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x37C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x380 "SW_PAD_CTL_PAD_GPIO_AD_16,SW_PAD_CTL_PAD_GPIO_AD_16 SW PAD Control Register" bitfld.long 0x380 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x380 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x380 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x380 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x380 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x380 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x380 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x384 "SW_PAD_CTL_PAD_GPIO_AD_17,SW_PAD_CTL_PAD_GPIO_AD_17 SW PAD Control Register" bitfld.long 0x384 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x384 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x384 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x384 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x384 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x384 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x384 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x388 "SW_PAD_CTL_PAD_GPIO_AD_18,SW_PAD_CTL_PAD_GPIO_AD_18 SW PAD Control Register" bitfld.long 0x388 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x388 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x388 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x388 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x388 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x388 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x388 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x38C "SW_PAD_CTL_PAD_GPIO_AD_19,SW_PAD_CTL_PAD_GPIO_AD_19 SW PAD Control Register" bitfld.long 0x38C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x38C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x38C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x38C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x38C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x38C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x38C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x390 "SW_PAD_CTL_PAD_GPIO_AD_20,SW_PAD_CTL_PAD_GPIO_AD_20 SW PAD Control Register" bitfld.long 0x390 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x390 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x390 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x390 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x390 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x390 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x390 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x394 "SW_PAD_CTL_PAD_GPIO_AD_21,SW_PAD_CTL_PAD_GPIO_AD_21 SW PAD Control Register" bitfld.long 0x394 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x394 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x394 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x394 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x394 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x394 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x394 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x398 "SW_PAD_CTL_PAD_GPIO_AD_22,SW_PAD_CTL_PAD_GPIO_AD_22 SW PAD Control Register" bitfld.long 0x398 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x398 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x398 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x398 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x398 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x398 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x398 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x39C "SW_PAD_CTL_PAD_GPIO_AD_23,SW_PAD_CTL_PAD_GPIO_AD_23 SW PAD Control Register" bitfld.long 0x39C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x39C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x39C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x39C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x39C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x39C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x39C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3A0 "SW_PAD_CTL_PAD_GPIO_AD_24,SW_PAD_CTL_PAD_GPIO_AD_24 SW PAD Control Register" bitfld.long 0x3A0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3A0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3A0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3A0 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3A0 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3A0 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3A0 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3A4 "SW_PAD_CTL_PAD_GPIO_AD_25,SW_PAD_CTL_PAD_GPIO_AD_25 SW PAD Control Register" bitfld.long 0x3A4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3A4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3A4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3A4 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3A4 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3A4 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3A4 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3A8 "SW_PAD_CTL_PAD_GPIO_AD_26,SW_PAD_CTL_PAD_GPIO_AD_26 SW PAD Control Register" bitfld.long 0x3A8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3A8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3A8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3A8 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3A8 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3A8 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3A8 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3AC "SW_PAD_CTL_PAD_GPIO_AD_27,SW_PAD_CTL_PAD_GPIO_AD_27 SW PAD Control Register" bitfld.long 0x3AC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3AC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3AC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3AC 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3AC 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3AC 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3AC 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3B0 "SW_PAD_CTL_PAD_GPIO_AD_28,SW_PAD_CTL_PAD_GPIO_AD_28 SW PAD Control Register" bitfld.long 0x3B0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3B0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3B0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3B0 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3B0 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3B0 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3B0 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3B4 "SW_PAD_CTL_PAD_GPIO_AD_29,SW_PAD_CTL_PAD_GPIO_AD_29 SW PAD Control Register" bitfld.long 0x3B4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3B4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3B4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3B4 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3B4 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3B4 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3B4 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3B8 "SW_PAD_CTL_PAD_GPIO_AD_30,SW_PAD_CTL_PAD_GPIO_AD_30 SW PAD Control Register" bitfld.long 0x3B8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3B8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3B8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3B8 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3B8 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3B8 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3B8 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3BC "SW_PAD_CTL_PAD_GPIO_AD_31,SW_PAD_CTL_PAD_GPIO_AD_31 SW PAD Control Register" bitfld.long 0x3BC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3BC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3BC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3BC 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3BC 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3BC 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3BC 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3C0 "SW_PAD_CTL_PAD_GPIO_AD_32,SW_PAD_CTL_PAD_GPIO_AD_32 SW PAD Control Register" bitfld.long 0x3C0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3C0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3C0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3C0 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3C0 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3C0 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3C0 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3C4 "SW_PAD_CTL_PAD_GPIO_AD_33,SW_PAD_CTL_PAD_GPIO_AD_33 SW PAD Control Register" bitfld.long 0x3C4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3C4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3C4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3C4 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3C4 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3C4 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3C4 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3C8 "SW_PAD_CTL_PAD_GPIO_AD_34,SW_PAD_CTL_PAD_GPIO_AD_34 SW PAD Control Register" bitfld.long 0x3C8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3C8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3C8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3C8 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3C8 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3C8 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3C8 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3CC "SW_PAD_CTL_PAD_GPIO_AD_35,SW_PAD_CTL_PAD_GPIO_AD_35 SW PAD Control Register" bitfld.long 0x3CC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3CC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3CC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3CC 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x3CC 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x3CC 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x3CC 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3D0 "SW_PAD_CTL_PAD_GPIO_SD_B1_00,SW_PAD_CTL_PAD_GPIO_SD_B1_00 SW PAD Control Register" bitfld.long 0x3D0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3D0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3D0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3D0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3D0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3D4 "SW_PAD_CTL_PAD_GPIO_SD_B1_01,SW_PAD_CTL_PAD_GPIO_SD_B1_01 SW PAD Control Register" bitfld.long 0x3D4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3D4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3D4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3D4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3D4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3D8 "SW_PAD_CTL_PAD_GPIO_SD_B1_02,SW_PAD_CTL_PAD_GPIO_SD_B1_02 SW PAD Control Register" bitfld.long 0x3D8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3D8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3D8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3D8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3D8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3DC "SW_PAD_CTL_PAD_GPIO_SD_B1_03,SW_PAD_CTL_PAD_GPIO_SD_B1_03 SW PAD Control Register" bitfld.long 0x3DC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3DC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3DC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3DC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3DC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3E0 "SW_PAD_CTL_PAD_GPIO_SD_B1_04,SW_PAD_CTL_PAD_GPIO_SD_B1_04 SW PAD Control Register" bitfld.long 0x3E0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3E0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3E0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3E0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3E0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3E4 "SW_PAD_CTL_PAD_GPIO_SD_B1_05,SW_PAD_CTL_PAD_GPIO_SD_B1_05 SW PAD Control Register" bitfld.long 0x3E4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3E4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3E4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3E4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3E4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3E8 "SW_PAD_CTL_PAD_GPIO_SD_B2_00,SW_PAD_CTL_PAD_GPIO_SD_B2_00 SW PAD Control Register" bitfld.long 0x3E8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3E8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3E8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3E8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3E8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3EC "SW_PAD_CTL_PAD_GPIO_SD_B2_01,SW_PAD_CTL_PAD_GPIO_SD_B2_01 SW PAD Control Register" bitfld.long 0x3EC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3EC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3EC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3EC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3EC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3F0 "SW_PAD_CTL_PAD_GPIO_SD_B2_02,SW_PAD_CTL_PAD_GPIO_SD_B2_02 SW PAD Control Register" bitfld.long 0x3F0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3F0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3F0 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3F0 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3F0 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3F4 "SW_PAD_CTL_PAD_GPIO_SD_B2_03,SW_PAD_CTL_PAD_GPIO_SD_B2_03 SW PAD Control Register" bitfld.long 0x3F4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3F4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3F4 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3F4 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3F4 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3F8 "SW_PAD_CTL_PAD_GPIO_SD_B2_04,SW_PAD_CTL_PAD_GPIO_SD_B2_04 SW PAD Control Register" bitfld.long 0x3F8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3F8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3F8 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3F8 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3F8 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x3FC "SW_PAD_CTL_PAD_GPIO_SD_B2_05,SW_PAD_CTL_PAD_GPIO_SD_B2_05 SW PAD Control Register" bitfld.long 0x3FC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3FC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3FC 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x3FC 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x3FC 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x400 "SW_PAD_CTL_PAD_GPIO_SD_B2_06,SW_PAD_CTL_PAD_GPIO_SD_B2_06 SW PAD Control Register" bitfld.long 0x400 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x400 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x400 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x400 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x400 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x404 "SW_PAD_CTL_PAD_GPIO_SD_B2_07,SW_PAD_CTL_PAD_GPIO_SD_B2_07 SW PAD Control Register" bitfld.long 0x404 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x404 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x404 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x404 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x404 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x408 "SW_PAD_CTL_PAD_GPIO_SD_B2_08,SW_PAD_CTL_PAD_GPIO_SD_B2_08 SW PAD Control Register" bitfld.long 0x408 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x408 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x408 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x408 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x408 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x40C "SW_PAD_CTL_PAD_GPIO_SD_B2_09,SW_PAD_CTL_PAD_GPIO_SD_B2_09 SW PAD Control Register" bitfld.long 0x40C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x40C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x40C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x40C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x40C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x410 "SW_PAD_CTL_PAD_GPIO_SD_B2_10,SW_PAD_CTL_PAD_GPIO_SD_B2_10 SW PAD Control Register" bitfld.long 0x410 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x410 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x410 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x410 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x410 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x414 "SW_PAD_CTL_PAD_GPIO_SD_B2_11,SW_PAD_CTL_PAD_GPIO_SD_B2_11 SW PAD Control Register" bitfld.long 0x414 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x414 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x414 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x414 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x414 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x418 "SW_PAD_CTL_PAD_GPIO_DISP_B1_00,SW_PAD_CTL_PAD_GPIO_DISP_B1_00 SW PAD Control Register" bitfld.long 0x418 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x418 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x418 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x418 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x418 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x41C "SW_PAD_CTL_PAD_GPIO_DISP_B1_01,SW_PAD_CTL_PAD_GPIO_DISP_B1_01 SW PAD Control Register" bitfld.long 0x41C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x41C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x41C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x41C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x41C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x420 "SW_PAD_CTL_PAD_GPIO_DISP_B1_02,SW_PAD_CTL_PAD_GPIO_DISP_B1_02 SW PAD Control Register" bitfld.long 0x420 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x420 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x420 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x420 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x420 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x424 "SW_PAD_CTL_PAD_GPIO_DISP_B1_03,SW_PAD_CTL_PAD_GPIO_DISP_B1_03 SW PAD Control Register" bitfld.long 0x424 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x424 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x424 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x424 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x424 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x428 "SW_PAD_CTL_PAD_GPIO_DISP_B1_04,SW_PAD_CTL_PAD_GPIO_DISP_B1_04 SW PAD Control Register" bitfld.long 0x428 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x428 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x428 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x428 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x428 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x42C "SW_PAD_CTL_PAD_GPIO_DISP_B1_05,SW_PAD_CTL_PAD_GPIO_DISP_B1_05 SW PAD Control Register" bitfld.long 0x42C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x42C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x42C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x42C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x42C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x430 "SW_PAD_CTL_PAD_GPIO_DISP_B1_06,SW_PAD_CTL_PAD_GPIO_DISP_B1_06 SW PAD Control Register" bitfld.long 0x430 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x430 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x430 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x430 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x430 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x434 "SW_PAD_CTL_PAD_GPIO_DISP_B1_07,SW_PAD_CTL_PAD_GPIO_DISP_B1_07 SW PAD Control Register" bitfld.long 0x434 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x434 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x434 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x434 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x434 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x438 "SW_PAD_CTL_PAD_GPIO_DISP_B1_08,SW_PAD_CTL_PAD_GPIO_DISP_B1_08 SW PAD Control Register" bitfld.long 0x438 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x438 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x438 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x438 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x438 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x43C "SW_PAD_CTL_PAD_GPIO_DISP_B1_09,SW_PAD_CTL_PAD_GPIO_DISP_B1_09 SW PAD Control Register" bitfld.long 0x43C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x43C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x43C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x43C 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x43C 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x440 "SW_PAD_CTL_PAD_GPIO_DISP_B1_10,SW_PAD_CTL_PAD_GPIO_DISP_B1_10 SW PAD Control Register" bitfld.long 0x440 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x440 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x440 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x440 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x440 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x444 "SW_PAD_CTL_PAD_GPIO_DISP_B1_11,SW_PAD_CTL_PAD_GPIO_DISP_B1_11 SW PAD Control Register" bitfld.long 0x444 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x444 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x444 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x444 2.--3. "PULL,Pull Down Pull Up Field" "0: Forbidden,1: Internal pullup resistor enabled,2: Internal pulldown resistor enabled,3: No Pull" newline bitfld.long 0x444 1. "PDRV,PDRV Field" "0: high drive strength,1: normal drive strength" line.long 0x448 "SW_PAD_CTL_PAD_GPIO_DISP_B2_00,SW_PAD_CTL_PAD_GPIO_DISP_B2_00 SW PAD Control Register" bitfld.long 0x448 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x448 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x448 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x448 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x448 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x448 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x448 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x44C "SW_PAD_CTL_PAD_GPIO_DISP_B2_01,SW_PAD_CTL_PAD_GPIO_DISP_B2_01 SW PAD Control Register" bitfld.long 0x44C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x44C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x44C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x44C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x44C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x44C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x44C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x450 "SW_PAD_CTL_PAD_GPIO_DISP_B2_02,SW_PAD_CTL_PAD_GPIO_DISP_B2_02 SW PAD Control Register" bitfld.long 0x450 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x450 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x450 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x450 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x450 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x450 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x450 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x454 "SW_PAD_CTL_PAD_GPIO_DISP_B2_03,SW_PAD_CTL_PAD_GPIO_DISP_B2_03 SW PAD Control Register" bitfld.long 0x454 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x454 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x454 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x454 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x454 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x454 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x454 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x458 "SW_PAD_CTL_PAD_GPIO_DISP_B2_04,SW_PAD_CTL_PAD_GPIO_DISP_B2_04 SW PAD Control Register" bitfld.long 0x458 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x458 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x458 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x458 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x458 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x458 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x458 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x45C "SW_PAD_CTL_PAD_GPIO_DISP_B2_05,SW_PAD_CTL_PAD_GPIO_DISP_B2_05 SW PAD Control Register" bitfld.long 0x45C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x45C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x45C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x45C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x45C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x45C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x45C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x460 "SW_PAD_CTL_PAD_GPIO_DISP_B2_06,SW_PAD_CTL_PAD_GPIO_DISP_B2_06 SW PAD Control Register" bitfld.long 0x460 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x460 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x460 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x460 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x460 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x460 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x460 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x464 "SW_PAD_CTL_PAD_GPIO_DISP_B2_07,SW_PAD_CTL_PAD_GPIO_DISP_B2_07 SW PAD Control Register" bitfld.long 0x464 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x464 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x464 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x464 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x464 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x464 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x464 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x468 "SW_PAD_CTL_PAD_GPIO_DISP_B2_08,SW_PAD_CTL_PAD_GPIO_DISP_B2_08 SW PAD Control Register" bitfld.long 0x468 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x468 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x468 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x468 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x468 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x468 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x468 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x46C "SW_PAD_CTL_PAD_GPIO_DISP_B2_09,SW_PAD_CTL_PAD_GPIO_DISP_B2_09 SW PAD Control Register" bitfld.long 0x46C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x46C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x46C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x46C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x46C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x46C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x46C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x470 "SW_PAD_CTL_PAD_GPIO_DISP_B2_10,SW_PAD_CTL_PAD_GPIO_DISP_B2_10 SW PAD Control Register" bitfld.long 0x470 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x470 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x470 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x470 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x470 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x470 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x470 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x474 "SW_PAD_CTL_PAD_GPIO_DISP_B2_11,SW_PAD_CTL_PAD_GPIO_DISP_B2_11 SW PAD Control Register" bitfld.long 0x474 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x474 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x474 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x474 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x474 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x474 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x474 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x478 "SW_PAD_CTL_PAD_GPIO_DISP_B2_12,SW_PAD_CTL_PAD_GPIO_DISP_B2_12 SW PAD Control Register" bitfld.long 0x478 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x478 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x478 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x478 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x478 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x478 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x478 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x47C "SW_PAD_CTL_PAD_GPIO_DISP_B2_13,SW_PAD_CTL_PAD_GPIO_DISP_B2_13 SW PAD Control Register" bitfld.long 0x47C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x47C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x47C 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x47C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x47C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x47C 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x47C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x480 "SW_PAD_CTL_PAD_GPIO_DISP_B2_14,SW_PAD_CTL_PAD_GPIO_DISP_B2_14 SW PAD Control Register" bitfld.long 0x480 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x480 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x480 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x480 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x480 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x480 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x480 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x484 "SW_PAD_CTL_PAD_GPIO_DISP_B2_15,SW_PAD_CTL_PAD_GPIO_DISP_B2_15 SW PAD Control Register" bitfld.long 0x484 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x484 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x484 4. "ODE,Open Drain Field" "0: Disabled,1: Enabled" bitfld.long 0x484 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x484 2. "PUE,Pull / Keep Select Field" "0: Pull Disable Highz,1: Pull Enable" bitfld.long 0x484 1. "DSE,Drive Strength Field" "0: normal drive strength,1: high drive strength" newline bitfld.long 0x484 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x488 "FLEXCAN1_RX_SELECT_INPUT,FLEXCAN1_RX_SELECT_INPUT DAISY Register" bitfld.long 0x488 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_07 for Mode: ALT1,1: Selecting Pad: GPIO_DISP_B2_13 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B2_15 for Mode: ALT6,?" line.long 0x48C "FLEXCAN2_RX_SELECT_INPUT,FLEXCAN2_RX_SELECT_INPUT DAISY Register" bitfld.long 0x48C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_01 for Mode: ALT1,1: Selecting Pad: GPIO_AD_31 for Mode: ALT2" group.long 0x4A8++0x43 line.long 0x0 "ENET_IPG_CLK_RMII_SELECT_INPUT,ENET_IPG_CLK_RMII_SELECT_INPUT DAISY Register" bitfld.long 0x0 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_29 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_05 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B2_13 for Mode: ALT4,?" line.long 0x4 "ENET_MAC0_MDIO_SELECT_INPUT,ENET_MAC0_MDIO_SELECT_INPUT DAISY Register" bitfld.long 0x4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_20 for Mode: ALT1,1: Selecting Pad: GPIO_AD_33 for Mode: ALT3" line.long 0x8 "ENET_MAC0_RXDATA_SELECT_INPUT_0,ENET_MAC0_RXDATA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_26 for Mode: ALT3,1: Selecting Pad: GPIO_DISP_B2_06 for Mode: ALT1" line.long 0xC "ENET_MAC0_RXDATA_SELECT_INPUT_1,ENET_MAC0_RXDATA_SELECT_INPUT_1 DAISY Register" bitfld.long 0xC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_27 for Mode: ALT3,1: Selecting Pad: GPIO_DISP_B2_07 for Mode: ALT1" line.long 0x10 "ENET_MAC0_RXEN_SELECT_INPUT,ENET_MAC0_RXEN_SELECT_INPUT DAISY Register" bitfld.long 0x10 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_24 for Mode: ALT3,1: Selecting Pad: GPIO_DISP_B2_08 for Mode: ALT1" line.long 0x14 "ENET_MAC0_RXERR_SELECT_INPUT,ENET_MAC0_RXERR_SELECT_INPUT DAISY Register" bitfld.long 0x14 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_25 for Mode: ALT3,1: Selecting Pad: GPIO_DISP_B2_09 for Mode: ALT1" line.long 0x18 "ENET_MAC0_TXCLK_SELECT_INPUT,ENET_MAC0_TXCLK_SELECT_INPUT DAISY Register" bitfld.long 0x18 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_29 for Mode: ALT3,1: Selecting Pad: GPIO_DISP_B2_05 for Mode: ALT1" line.long 0x1C "ENET_1G_IPG_CLK_RMII_SELECT_INPUT,ENET_1G_IPG_CLK_RMII_SELECT_INPUT DAISY Register" bitfld.long 0x1C 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_19 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_11 for Mode: ALT3,2: Selecting Pad: GPIO_DISP_B1_11 for Mode: ALT2,3: Selecting Pad: GPIO_DISP_B2_14 for Mode: ALT4" line.long 0x20 "ENET_1G_MAC0_MDIO_SELECT_INPUT,ENET_1G_MAC0_MDIO_SELECT_INPUT DAISY Register" bitfld.long 0x20 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_41 for Mode: ALT7,1: Selecting Pad: GPIO_EMC_B2_20 for Mode: ALT2,2: Selecting Pad: GPIO_AD_17 for Mode: ALT9,3: Selecting Pad: GPIO_AD_33 for Mode: ALT9" line.long 0x24 "ENET_1G_MAC0_RXCLK_SELECT_INPUT,ENET_1G_MAC0_RXCLK_SELECT_INPUT DAISY Register" bitfld.long 0x24 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_05 for Mode: ALT7,1: Selecting Pad: GPIO_SD_B2_01 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_01 for Mode: ALT1,?" line.long 0x28 "ENET_1G_MAC0_RXDATA_0_SELECT_INPUT,ENET_1G_MAC0_RXDATA_0_SELECT_INPUT DAISY Register" bitfld.long 0x28 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_15 for Mode: ALT2,1: Selecting Pad: GPIO_SD_B2_02 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_02 for Mode: ALT1,?" line.long 0x2C "ENET_1G_MAC0_RXDATA_1_SELECT_INPUT,ENET_1G_MAC0_RXDATA_1_SELECT_INPUT DAISY Register" bitfld.long 0x2C 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_16 for Mode: ALT2,1: Selecting Pad: GPIO_SD_B2_03 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_03 for Mode: ALT1,?" line.long 0x30 "ENET_1G_MAC0_RXDATA_2_SELECT_INPUT,ENET_1G_MAC0_RXDATA_2_SELECT_INPUT DAISY Register" bitfld.long 0x30 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_08 for Mode: ALT7,1: Selecting Pad: GPIO_SD_B2_04 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_04 for Mode: ALT1,?" line.long 0x34 "ENET_1G_MAC0_RXDATA_3_SELECT_INPUT,ENET_1G_MAC0_RXDATA_3_SELECT_INPUT DAISY Register" bitfld.long 0x34 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_07 for Mode: ALT7,1: Selecting Pad: GPIO_SD_B2_05 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_05 for Mode: ALT1,?" line.long 0x38 "ENET_1G_MAC0_RXEN_SELECT_INPUT,ENET_1G_MAC0_RXEN_SELECT_INPUT DAISY Register" bitfld.long 0x38 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_17 for Mode: ALT2,1: Selecting Pad: GPIO_SD_B2_00 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_00 for Mode: ALT1,?" line.long 0x3C "ENET_1G_MAC0_RXERR_SELECT_INPUT,ENET_1G_MAC0_RXERR_SELECT_INPUT DAISY Register" bitfld.long 0x3C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_18 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B1_01 for Mode: ALT2" line.long 0x40 "ENET_1G_MAC0_TXCLK_SELECT_INPUT,ENET_1G_MAC0_TXCLK_SELECT_INPUT DAISY Register" bitfld.long 0x40 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_14 for Mode: ALT2,1: Selecting Pad: GPIO_SD_B2_11 for Mode: ALT2,2: Selecting Pad: GPIO_DISP_B1_11 for Mode: ALT1,?" group.long 0x500++0x183 line.long 0x0 "FLEXPWM1_PWMA_SELECT_INPUT_0,FLEXPWM1_PWMA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_23 for Mode: ALT1,1: Selecting Pad: GPIO_AD_00 for Mode: ALT4" line.long 0x4 "FLEXPWM1_PWMA_SELECT_INPUT_1,FLEXPWM1_PWMA_SELECT_INPUT_1 DAISY Register" bitfld.long 0x4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_25 for Mode: ALT1,1: Selecting Pad: GPIO_AD_02 for Mode: ALT4" line.long 0x8 "FLEXPWM1_PWMA_SELECT_INPUT_2,FLEXPWM1_PWMA_SELECT_INPUT_2 DAISY Register" bitfld.long 0x8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_27 for Mode: ALT1,1: Selecting Pad: GPIO_AD_04 for Mode: ALT4" line.long 0xC "FLEXPWM1_PWMB_SELECT_INPUT_0,FLEXPWM1_PWMB_SELECT_INPUT_0 DAISY Register" bitfld.long 0xC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_24 for Mode: ALT1,1: Selecting Pad: GPIO_AD_01 for Mode: ALT4" line.long 0x10 "FLEXPWM1_PWMB_SELECT_INPUT_1,FLEXPWM1_PWMB_SELECT_INPUT_1 DAISY Register" bitfld.long 0x10 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_26 for Mode: ALT1,1: Selecting Pad: GPIO_AD_03 for Mode: ALT4" line.long 0x14 "FLEXPWM1_PWMB_SELECT_INPUT_2,FLEXPWM1_PWMB_SELECT_INPUT_2 DAISY Register" bitfld.long 0x14 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_28 for Mode: ALT1,1: Selecting Pad: GPIO_AD_05 for Mode: ALT4" line.long 0x18 "FLEXPWM2_PWMA_SELECT_INPUT_0,FLEXPWM2_PWMA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x18 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_06 for Mode: ALT1,1: Selecting Pad: GPIO_AD_24 for Mode: ALT4" line.long 0x1C "FLEXPWM2_PWMA_SELECT_INPUT_1,FLEXPWM2_PWMA_SELECT_INPUT_1 DAISY Register" bitfld.long 0x1C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_08 for Mode: ALT1,1: Selecting Pad: GPIO_AD_26 for Mode: ALT4" line.long 0x20 "FLEXPWM2_PWMA_SELECT_INPUT_2,FLEXPWM2_PWMA_SELECT_INPUT_2 DAISY Register" bitfld.long 0x20 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_10 for Mode: ALT1,1: Selecting Pad: GPIO_AD_28 for Mode: ALT4" line.long 0x24 "FLEXPWM2_PWMB_SELECT_INPUT_0,FLEXPWM2_PWMB_SELECT_INPUT_0 DAISY Register" bitfld.long 0x24 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_07 for Mode: ALT1,1: Selecting Pad: GPIO_AD_25 for Mode: ALT4" line.long 0x28 "FLEXPWM2_PWMB_SELECT_INPUT_1,FLEXPWM2_PWMB_SELECT_INPUT_1 DAISY Register" bitfld.long 0x28 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_09 for Mode: ALT1,1: Selecting Pad: GPIO_AD_27 for Mode: ALT4" line.long 0x2C "FLEXPWM2_PWMB_SELECT_INPUT_2,FLEXPWM2_PWMB_SELECT_INPUT_2 DAISY Register" bitfld.long 0x2C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_11 for Mode: ALT1,1: Selecting Pad: GPIO_AD_29 for Mode: ALT4" line.long 0x30 "FLEXPWM3_PWMA_SELECT_INPUT_0,FLEXPWM3_PWMA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x30 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_29 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_00 for Mode: ALT11" line.long 0x34 "FLEXPWM3_PWMA_SELECT_INPUT_1,FLEXPWM3_PWMA_SELECT_INPUT_1 DAISY Register" bitfld.long 0x34 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_31 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_02 for Mode: ALT11" line.long 0x38 "FLEXPWM3_PWMA_SELECT_INPUT_2,FLEXPWM3_PWMA_SELECT_INPUT_2 DAISY Register" bitfld.long 0x38 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_33 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_04 for Mode: ALT11" line.long 0x3C "FLEXPWM3_PWMA_SELECT_INPUT_3,FLEXPWM3_PWMA_SELECT_INPUT_3 DAISY Register" bitfld.long 0x3C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_21 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_06 for Mode: ALT11" line.long 0x40 "FLEXPWM3_PWMB_SELECT_INPUT_0,FLEXPWM3_PWMB_SELECT_INPUT_0 DAISY Register" bitfld.long 0x40 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_30 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT11" line.long 0x44 "FLEXPWM3_PWMB_SELECT_INPUT_1,FLEXPWM3_PWMB_SELECT_INPUT_1 DAISY Register" bitfld.long 0x44 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_32 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_03 for Mode: ALT11" line.long 0x48 "FLEXPWM3_PWMB_SELECT_INPUT_2,FLEXPWM3_PWMB_SELECT_INPUT_2 DAISY Register" bitfld.long 0x48 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_34 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_05 for Mode: ALT11" line.long 0x4C "FLEXPWM3_PWMB_SELECT_INPUT_3,FLEXPWM3_PWMB_SELECT_INPUT_3 DAISY Register" bitfld.long 0x4C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_22 for Mode: ALT1,1: Selecting Pad: GPIO_EMC_B2_07 for Mode: ALT11" line.long 0x50 "FLEXSPI1_I_DQS_FA_SELECT_INPUT,FLEXSPI1_I_DQS_FA_SELECT_INPUT DAISY Register" bitfld.long 0x50 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_18 for Mode: ALT6,1: Selecting Pad: GPIO_AD_17 for Mode: ALT3,2: Selecting Pad: GPIO_SD_B2_05 for Mode: ALT1,?" line.long 0x54 "FLEXSPI1_I_IO_FA_SELECT_INPUT_0,FLEXSPI1_I_IO_FA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x54 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_20 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_08 for Mode: ALT1" line.long 0x58 "FLEXSPI1_I_IO_FA_SELECT_INPUT_1,FLEXSPI1_I_IO_FA_SELECT_INPUT_1 DAISY Register" bitfld.long 0x58 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_21 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_09 for Mode: ALT1" line.long 0x5C "FLEXSPI1_I_IO_FA_SELECT_INPUT_2,FLEXSPI1_I_IO_FA_SELECT_INPUT_2 DAISY Register" bitfld.long 0x5C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_22 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_10 for Mode: ALT1" line.long 0x60 "FLEXSPI1_I_IO_FA_SELECT_INPUT_3,FLEXSPI1_I_IO_FA_SELECT_INPUT_3 DAISY Register" bitfld.long 0x60 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_23 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_11 for Mode: ALT1" line.long 0x64 "FLEXSPI1_I_IO_FB_SELECT_INPUT_0,FLEXSPI1_I_IO_FB_SELECT_INPUT_0 DAISY Register" bitfld.long 0x64 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_15 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_03 for Mode: ALT1" line.long 0x68 "FLEXSPI1_I_IO_FB_SELECT_INPUT_1,FLEXSPI1_I_IO_FB_SELECT_INPUT_1 DAISY Register" bitfld.long 0x68 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_14 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_02 for Mode: ALT1" line.long 0x6C "FLEXSPI1_I_IO_FB_SELECT_INPUT_2,FLEXSPI1_I_IO_FB_SELECT_INPUT_2 DAISY Register" bitfld.long 0x6C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_13 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_01 for Mode: ALT1" line.long 0x70 "FLEXSPI1_I_IO_FB_SELECT_INPUT_3,FLEXSPI1_I_IO_FB_SELECT_INPUT_3 DAISY Register" bitfld.long 0x70 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_12 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_00 for Mode: ALT1" line.long 0x74 "FLEXSPI1_I_SCK_FA_SELECT_INPUT,FLEXSPI1_I_SCK_FA_SELECT_INPUT DAISY Register" bitfld.long 0x74 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_19 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_07 for Mode: ALT1" line.long 0x78 "FLEXSPI1_I_SCK_FB_SELECT_INPUT,FLEXSPI1_I_SCK_FB_SELECT_INPUT DAISY Register" bitfld.long 0x78 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_16 for Mode: ALT3,1: Selecting Pad: GPIO_SD_B2_04 for Mode: ALT1" line.long 0x7C "FLEXSPI2_I_IO_FA_SELECT_INPUT_0,FLEXSPI2_I_IO_FA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x7C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_13 for Mode: ALT4,1: Selecting Pad: GPIO_SD_B1_02 for Mode: ALT6" line.long 0x80 "FLEXSPI2_I_IO_FA_SELECT_INPUT_1,FLEXSPI2_I_IO_FA_SELECT_INPUT_1 DAISY Register" bitfld.long 0x80 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_14 for Mode: ALT4,1: Selecting Pad: GPIO_SD_B1_03 for Mode: ALT6" line.long 0x84 "FLEXSPI2_I_IO_FA_SELECT_INPUT_2,FLEXSPI2_I_IO_FA_SELECT_INPUT_2 DAISY Register" bitfld.long 0x84 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_15 for Mode: ALT4,1: Selecting Pad: GPIO_SD_B1_04 for Mode: ALT6" line.long 0x88 "FLEXSPI2_I_IO_FA_SELECT_INPUT_3,FLEXSPI2_I_IO_FA_SELECT_INPUT_3 DAISY Register" bitfld.long 0x88 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_16 for Mode: ALT4,1: Selecting Pad: GPIO_SD_B1_05 for Mode: ALT6" line.long 0x8C "FLEXSPI2_I_SCK_FA_SELECT_INPUT,FLEXSPI2_I_SCK_FA_SELECT_INPUT DAISY Register" bitfld.long 0x8C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_10 for Mode: ALT4,1: Selecting Pad: GPIO_SD_B1_01 for Mode: ALT6" line.long 0x90 "GPT3_CAPIN1_SELECT_INPUT,GPT3_CAPIN1_SELECT_INPUT DAISY Register" bitfld.long 0x90 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_06 for Mode: ALT1,1: Selecting Pad: GPIO_AD_06 for Mode: ALT3" line.long 0x94 "GPT3_CAPIN2_SELECT_INPUT,GPT3_CAPIN2_SELECT_INPUT DAISY Register" bitfld.long 0x94 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_07 for Mode: ALT1,1: Selecting Pad: GPIO_AD_07 for Mode: ALT3" line.long 0x98 "GPT3_CLKIN_SELECT_INPUT,GPT3_CLKIN_SELECT_INPUT DAISY Register" bitfld.long 0x98 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_05 for Mode: ALT1,1: Selecting Pad: GPIO_AD_11 for Mode: ALT3" line.long 0x9C "KPP_COL_SELECT_INPUT_6,KPP_COL_SELECT_INPUT_6 DAISY Register" bitfld.long 0x9C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_23 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_03 for Mode: ALT8" line.long 0xA0 "KPP_COL_SELECT_INPUT_7,KPP_COL_SELECT_INPUT_7 DAISY Register" bitfld.long 0xA0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_21 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_01 for Mode: ALT8" line.long 0xA4 "KPP_ROW_SELECT_INPUT_6,KPP_ROW_SELECT_INPUT_6 DAISY Register" bitfld.long 0xA4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_22 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_02 for Mode: ALT8" line.long 0xA8 "KPP_ROW_SELECT_INPUT_7,KPP_ROW_SELECT_INPUT_7 DAISY Register" bitfld.long 0xA8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_20 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_00 for Mode: ALT8" line.long 0xAC "LPI2C1_LPI2C_SCL_SELECT_INPUT,LPI2C1_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0xAC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_08 for Mode: ALT1,1: Selecting Pad: GPIO_AD_32 for Mode: ALT0" line.long 0xB0 "LPI2C1_LPI2C_SDA_SELECT_INPUT,LPI2C1_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0xB0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_09 for Mode: ALT1,1: Selecting Pad: GPIO_AD_33 for Mode: ALT0" line.long 0xB4 "LPI2C2_LPI2C_SCL_SELECT_INPUT,LPI2C2_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0xB4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_00 for Mode: ALT9,1: Selecting Pad: GPIO_AD_18 for Mode: ALT9" line.long 0xB8 "LPI2C2_LPI2C_SDA_SELECT_INPUT,LPI2C2_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0xB8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT9,1: Selecting Pad: GPIO_AD_19 for Mode: ALT9" line.long 0xBC "LPI2C3_LPI2C_SCL_SELECT_INPUT,LPI2C3_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0xBC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_DISP_B1_02 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_10 for Mode: ALT6" line.long 0xC0 "LPI2C3_LPI2C_SDA_SELECT_INPUT,LPI2C3_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0xC0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_DISP_B1_03 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_11 for Mode: ALT6" line.long 0xC4 "LPI2C4_LPI2C_SCL_SELECT_INPUT,LPI2C4_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0xC4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_24 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B2_12 for Mode: ALT6" line.long 0xC8 "LPI2C4_LPI2C_SDA_SELECT_INPUT,LPI2C4_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0xC8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_25 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B2_13 for Mode: ALT6" line.long 0xCC "LPSPI1_LPSPI_PCS_SELECT_INPUT_0,LPSPI1_LPSPI_PCS_SELECT_INPUT_0 DAISY Register" bitfld.long 0xCC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT8,1: Selecting Pad: GPIO_AD_29 for Mode: ALT0" line.long 0xD0 "LPSPI1_LPSPI_SCK_SELECT_INPUT,LPSPI1_LPSPI_SCK_SELECT_INPUT DAISY Register" bitfld.long 0xD0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_00 for Mode: ALT8,1: Selecting Pad: GPIO_AD_28 for Mode: ALT0" line.long 0xD4 "LPSPI1_LPSPI_SDI_SELECT_INPUT,LPSPI1_LPSPI_SDI_SELECT_INPUT DAISY Register" bitfld.long 0xD4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_03 for Mode: ALT8,1: Selecting Pad: GPIO_AD_31 for Mode: ALT0" line.long 0xD8 "LPSPI1_LPSPI_SDO_SELECT_INPUT,LPSPI1_LPSPI_SDO_SELECT_INPUT DAISY Register" bitfld.long 0xD8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_02 for Mode: ALT8,1: Selecting Pad: GPIO_AD_30 for Mode: ALT0" line.long 0xDC "LPSPI2_LPSPI_PCS_SELECT_INPUT_0,LPSPI2_LPSPI_PCS_SELECT_INPUT_0 DAISY Register" bitfld.long 0xDC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_25 for Mode: ALT1,1: Selecting Pad: GPIO_SD_B2_08 for Mode: ALT6" line.long 0xE0 "LPSPI2_LPSPI_PCS_SELECT_INPUT_1,LPSPI2_LPSPI_PCS_SELECT_INPUT_1 DAISY Register" bitfld.long 0xE0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_21 for Mode: ALT2,1: Selecting Pad: GPIO_SD_B2_11 for Mode: ALT6" line.long 0xE4 "LPSPI2_LPSPI_SCK_SELECT_INPUT,LPSPI2_LPSPI_SCK_SELECT_INPUT DAISY Register" bitfld.long 0xE4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_24 for Mode: ALT1,1: Selecting Pad: GPIO_SD_B2_07 for Mode: ALT6" line.long 0xE8 "LPSPI2_LPSPI_SDI_SELECT_INPUT,LPSPI2_LPSPI_SDI_SELECT_INPUT DAISY Register" bitfld.long 0xE8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_27 for Mode: ALT1,1: Selecting Pad: GPIO_SD_B2_10 for Mode: ALT6" line.long 0xEC "LPSPI2_LPSPI_SDO_SELECT_INPUT,LPSPI2_LPSPI_SDO_SELECT_INPUT DAISY Register" bitfld.long 0xEC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_26 for Mode: ALT1,1: Selecting Pad: GPIO_SD_B2_09 for Mode: ALT6" line.long 0xF0 "LPSPI3_LPSPI_PCS_SELECT_INPUT_0,LPSPI3_LPSPI_PCS_SELECT_INPUT_0 DAISY Register" bitfld.long 0xF0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_05 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_07 for Mode: ALT9" line.long 0xF4 "LPSPI3_LPSPI_PCS_SELECT_INPUT_1,LPSPI3_LPSPI_PCS_SELECT_INPUT_1 DAISY Register" bitfld.long 0xF4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_08 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_08 for Mode: ALT9" line.long 0xF8 "LPSPI3_LPSPI_PCS_SELECT_INPUT_2,LPSPI3_LPSPI_PCS_SELECT_INPUT_2 DAISY Register" bitfld.long 0xF8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_09 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_09 for Mode: ALT9" line.long 0xFC "LPSPI3_LPSPI_PCS_SELECT_INPUT_3,LPSPI3_LPSPI_PCS_SELECT_INPUT_3 DAISY Register" bitfld.long 0xFC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_10 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_10 for Mode: ALT9" line.long 0x100 "LPSPI3_LPSPI_SCK_SELECT_INPUT,LPSPI3_LPSPI_SCK_SELECT_INPUT DAISY Register" bitfld.long 0x100 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_04 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_04 for Mode: ALT9" line.long 0x104 "LPSPI3_LPSPI_SDI_SELECT_INPUT,LPSPI3_LPSPI_SDI_SELECT_INPUT DAISY Register" bitfld.long 0x104 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_07 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_05 for Mode: ALT9" line.long 0x108 "LPSPI3_LPSPI_SDO_SELECT_INPUT,LPSPI3_LPSPI_SDO_SELECT_INPUT DAISY Register" bitfld.long 0x108 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_06 for Mode: ALT8,1: Selecting Pad: GPIO_DISP_B1_06 for Mode: ALT9" line.long 0x10C "LPSPI4_LPSPI_PCS_SELECT_INPUT_0,LPSPI4_LPSPI_PCS_SELECT_INPUT_0 DAISY Register" bitfld.long 0x10C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_SD_B2_01 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B2_15 for Mode: ALT9" line.long 0x110 "LPSPI4_LPSPI_SCK_SELECT_INPUT,LPSPI4_LPSPI_SCK_SELECT_INPUT DAISY Register" bitfld.long 0x110 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_SD_B2_00 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B2_12 for Mode: ALT9" line.long 0x114 "LPSPI4_LPSPI_SDI_SELECT_INPUT,LPSPI4_LPSPI_SDI_SELECT_INPUT DAISY Register" bitfld.long 0x114 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_SD_B2_03 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B2_13 for Mode: ALT9" line.long 0x118 "LPSPI4_LPSPI_SDO_SELECT_INPUT,LPSPI4_LPSPI_SDO_SELECT_INPUT DAISY Register" bitfld.long 0x118 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_SD_B2_02 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B2_14 for Mode: ALT9" line.long 0x11C "LPUART1_LPUART_RXD_SELECT_INPUT,LPUART1_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0x11C 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_25 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B1_03 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B2_09 for Mode: ALT9,?" line.long 0x120 "LPUART1_LPUART_TXD_SELECT_INPUT,LPUART1_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0x120 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_24 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B1_02 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B2_08 for Mode: ALT9,?" line.long 0x124 "LPUART10_LPUART_RXD_SELECT_INPUT,LPUART10_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0x124 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_16 for Mode: ALT1,1: Selecting Pad: GPIO_AD_33 for Mode: ALT8" line.long 0x128 "LPUART10_LPUART_TXD_SELECT_INPUT,LPUART10_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0x128 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_15 for Mode: ALT1,1: Selecting Pad: GPIO_AD_32 for Mode: ALT8" line.long 0x12C "LPUART7_LPUART_RXD_SELECT_INPUT,LPUART7_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0x12C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_01 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B2_07 for Mode: ALT2" line.long 0x130 "LPUART7_LPUART_TXD_SELECT_INPUT,LPUART7_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0x130 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_00 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B2_06 for Mode: ALT2" line.long 0x134 "LPUART8_LPUART_RXD_SELECT_INPUT,LPUART8_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0x134 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_03 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B2_09 for Mode: ALT2" line.long 0x138 "LPUART8_LPUART_TXD_SELECT_INPUT,LPUART8_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0x138 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_02 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B2_08 for Mode: ALT2" line.long 0x13C "QTIMER1_TMR0_INPUT_SELECT_INPUT,QTIMER1_TMR0_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x13C 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_17 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_09 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_00 for Mode: ALT3,?" line.long 0x140 "QTIMER1_TMR1_INPUT_SELECT_INPUT,QTIMER1_TMR1_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x140 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_38 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_10 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_01 for Mode: ALT3,?" line.long 0x144 "QTIMER1_TMR2_INPUT_SELECT_INPUT,QTIMER1_TMR2_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x144 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_11 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B1_02 for Mode: ALT3" line.long 0x148 "QTIMER2_TMR0_INPUT_SELECT_INPUT,QTIMER2_TMR0_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x148 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_18 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_13 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_03 for Mode: ALT3,?" line.long 0x14C "QTIMER2_TMR1_INPUT_SELECT_INPUT,QTIMER2_TMR1_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x14C 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_39 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_14 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_04 for Mode: ALT3,?" line.long 0x150 "QTIMER2_TMR2_INPUT_SELECT_INPUT,QTIMER2_TMR2_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x150 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_15 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B1_05 for Mode: ALT3" line.long 0x154 "QTIMER3_TMR0_INPUT_SELECT_INPUT,QTIMER3_TMR0_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x154 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_19 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_17 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_06 for Mode: ALT3,?" line.long 0x158 "QTIMER3_TMR1_INPUT_SELECT_INPUT,QTIMER3_TMR1_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x158 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_00 for Mode: ALT2,1: Selecting Pad: GPIO_EMC_B2_18 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_07 for Mode: ALT3,?" line.long 0x15C "QTIMER3_TMR2_INPUT_SELECT_INPUT,QTIMER3_TMR2_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x15C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_19 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B1_08 for Mode: ALT3" line.long 0x160 "QTIMER4_TMR0_INPUT_SELECT_INPUT,QTIMER4_TMR0_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x160 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B1_20 for Mode: ALT2,1: Selecting Pad: GPIO_AD_04 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_09 for Mode: ALT3,?" line.long 0x164 "QTIMER4_TMR1_INPUT_SELECT_INPUT,QTIMER4_TMR1_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x164 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT2,1: Selecting Pad: GPIO_AD_05 for Mode: ALT9,2: Selecting Pad: GPIO_DISP_B1_10 for Mode: ALT3,?" line.long 0x168 "QTIMER4_TMR2_INPUT_SELECT_INPUT,QTIMER4_TMR2_INPUT_SELECT_INPUT DAISY Register" bitfld.long 0x168 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_06 for Mode: ALT9,1: Selecting Pad: GPIO_DISP_B1_11 for Mode: ALT3" line.long 0x16C "SAI1_IPG_CLK_SAI_MCLK_SELECT_INPUT,SAI1_IPG_CLK_SAI_MCLK_SELECT_INPUT DAISY Register" bitfld.long 0x16C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_17 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_03 for Mode: ALT4" line.long 0x170 "SAI1_SAI_RXBCLK_SELECT_INPUT,SAI1_SAI_RXBCLK_SELECT_INPUT DAISY Register" bitfld.long 0x170 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_19 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_05 for Mode: ALT4" line.long 0x174 "SAI1_SAI_RXDATA_SELECT_INPUT_0,SAI1_SAI_RXDATA_SELECT_INPUT_0 DAISY Register" bitfld.long 0x174 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_20 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_06 for Mode: ALT4" line.long 0x178 "SAI1_SAI_RXSYNC_SELECT_INPUT,SAI1_SAI_RXSYNC_SELECT_INPUT DAISY Register" bitfld.long 0x178 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_18 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_04 for Mode: ALT4" line.long 0x17C "SAI1_SAI_TXBCLK_SELECT_INPUT,SAI1_SAI_TXBCLK_SELECT_INPUT DAISY Register" bitfld.long 0x17C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_22 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_08 for Mode: ALT4" line.long 0x180 "SAI1_SAI_TXSYNC_SELECT_INPUT,SAI1_SAI_TXSYNC_SELECT_INPUT DAISY Register" bitfld.long 0x180 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_23 for Mode: ALT0,1: Selecting Pad: GPIO_DISP_B2_09 for Mode: ALT4" group.long 0x69C++0x7B line.long 0x0 "EMVSIM1_SIO_SELECT_INPUT,EMVSIM1_SIO_SELECT_INPUT DAISY Register" bitfld.long 0x0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_11 for Mode: ALT8,1: Selecting Pad: GPIO_AD_00 for Mode: ALT0" line.long 0x4 "EMVSIM1_IPP_SIMPD_SELECT_INPUT,EMVSIM1_IPP_SIMPD_SELECT_INPUT DAISY Register" bitfld.long 0x4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_15 for Mode: ALT8,1: Selecting Pad: GPIO_AD_04 for Mode: ALT0" line.long 0x8 "EMVSIM1_POWER_FAIL_SELECT_INPUT,EMVSIM1_POWER_FAIL_SELECT_INPUT DAISY Register" bitfld.long 0x8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_16 for Mode: ALT8,1: Selecting Pad: GPIO_AD_05 for Mode: ALT0" line.long 0xC "EMVSIM2_SIO_SELECT_INPUT,EMVSIM2_SIO_SELECT_INPUT DAISY Register" bitfld.long 0xC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_06 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_10 for Mode: ALT1" line.long 0x10 "EMVSIM2_IPP_SIMPD_SELECT_INPUT,EMVSIM2_IPP_SIMPD_SELECT_INPUT DAISY Register" bitfld.long 0x10 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_10 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_14 for Mode: ALT1" line.long 0x14 "EMVSIM2_POWER_FAIL_SELECT_INPUT,EMVSIM2_POWER_FAIL_SELECT_INPUT DAISY Register" bitfld.long 0x14 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_11 for Mode: ALT2,1: Selecting Pad: GPIO_DISP_B2_15 for Mode: ALT1" line.long 0x18 "SPDIF_SPDIF_IN1_SELECT_INPUT,SPDIF_SPDIF_IN1_SELECT_INPUT DAISY Register" bitfld.long 0x18 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_11 for Mode: ALT1,1: Selecting Pad: GPIO_AD_15 for Mode: ALT0,2: Selecting Pad: GPIO_DISP_B2_10 for Mode: ALT9,?" line.long 0x1C "USB_OTG2_OC_SELECT_INPUT,USB_OTG2_OC_SELECT_INPUT DAISY Register" bitfld.long 0x1C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_06 for Mode: ALT0,1: Selecting Pad: GPIO_AD_30 for Mode: ALT1" line.long 0x20 "USB_OTG_OC_SELECT_INPUT,USB_OTG_OC_SELECT_INPUT DAISY Register" bitfld.long 0x20 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_11 for Mode: ALT0,1: Selecting Pad: GPIO_AD_35 for Mode: ALT1" line.long 0x24 "USBPHY1_USB_ID_SELECT_INPUT,USBPHY1_USB_ID_SELECT_INPUT DAISY Register" bitfld.long 0x24 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_09 for Mode: ALT0,1: Selecting Pad: GPIO_AD_33 for Mode: ALT1" line.long 0x28 "USBPHY2_USB_ID_SELECT_INPUT,USBPHY2_USB_ID_SELECT_INPUT DAISY Register" bitfld.long 0x28 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_08 for Mode: ALT0,1: Selecting Pad: GPIO_AD_32 for Mode: ALT1" line.long 0x2C "USDHC1_IPP_CARD_DET_SELECT_INPUT,USDHC1_IPP_CARD_DET_SELECT_INPUT DAISY Register" bitfld.long 0x2C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_32 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B1_08 for Mode: ALT2" line.long 0x30 "USDHC1_IPP_WP_ON_SELECT_INPUT,USDHC1_IPP_WP_ON_SELECT_INPUT DAISY Register" bitfld.long 0x30 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_AD_33 for Mode: ALT4,1: Selecting Pad: GPIO_DISP_B1_09 for Mode: ALT2" line.long 0x34 "USDHC2_IPP_CARD_DET_SELECT_INPUT,USDHC2_IPP_CARD_DET_SELECT_INPUT DAISY Register" bitfld.long 0x34 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT1,1: Selecting Pad: GPIO_AD_26 for Mode: ALT11" line.long 0x38 "USDHC2_IPP_WP_ON_SELECT_INPUT,USDHC2_IPP_WP_ON_SELECT_INPUT DAISY Register" bitfld.long 0x38 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_02 for Mode: ALT1,1: Selecting Pad: GPIO_AD_27 for Mode: ALT11" line.long 0x3C "XBAR1_IN_SELECT_INPUT_20,XBAR1_IN_SELECT_INPUT_20 DAISY Register" bitfld.long 0x3C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_00 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_00 for Mode: ALT2" line.long 0x40 "XBAR1_IN_SELECT_INPUT_21,XBAR1_IN_SELECT_INPUT_21 DAISY Register" bitfld.long 0x40 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_01 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_01 for Mode: ALT2" line.long 0x44 "XBAR1_IN_SELECT_INPUT_22,XBAR1_IN_SELECT_INPUT_22 DAISY Register" bitfld.long 0x44 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_02 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_02 for Mode: ALT2" line.long 0x48 "XBAR1_IN_SELECT_INPUT_23,XBAR1_IN_SELECT_INPUT_23 DAISY Register" bitfld.long 0x48 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_03 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_03 for Mode: ALT2" line.long 0x4C "XBAR1_IN_SELECT_INPUT_24,XBAR1_IN_SELECT_INPUT_24 DAISY Register" bitfld.long 0x4C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_04 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_04 for Mode: ALT2" line.long 0x50 "XBAR1_IN_SELECT_INPUT_25,XBAR1_IN_SELECT_INPUT_25 DAISY Register" bitfld.long 0x50 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_05 for Mode: ALT6,1: Selecting Pad: GPIO_SD_B1_05 for Mode: ALT2" line.long 0x54 "XBAR1_IN_SELECT_INPUT_26,XBAR1_IN_SELECT_INPUT_26 DAISY Register" bitfld.long 0x54 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_06 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_00 for Mode: ALT4" line.long 0x58 "XBAR1_IN_SELECT_INPUT_27,XBAR1_IN_SELECT_INPUT_27 DAISY Register" bitfld.long 0x58 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_07 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_01 for Mode: ALT4" line.long 0x5C "XBAR1_IN_SELECT_INPUT_28,XBAR1_IN_SELECT_INPUT_28 DAISY Register" bitfld.long 0x5C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_08 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_02 for Mode: ALT4" line.long 0x60 "XBAR1_IN_SELECT_INPUT_29,XBAR1_IN_SELECT_INPUT_29 DAISY Register" bitfld.long 0x60 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_09 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_03 for Mode: ALT4" line.long 0x64 "XBAR1_IN_SELECT_INPUT_30,XBAR1_IN_SELECT_INPUT_30 DAISY Register" bitfld.long 0x64 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_10 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_04 for Mode: ALT4" line.long 0x68 "XBAR1_IN_SELECT_INPUT_31,XBAR1_IN_SELECT_INPUT_31 DAISY Register" bitfld.long 0x68 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_11 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_05 for Mode: ALT4" line.long 0x6C "XBAR1_IN_SELECT_INPUT_32,XBAR1_IN_SELECT_INPUT_32 DAISY Register" bitfld.long 0x6C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_12 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_06 for Mode: ALT4" line.long 0x70 "XBAR1_IN_SELECT_INPUT_33,XBAR1_IN_SELECT_INPUT_33 DAISY Register" bitfld.long 0x70 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_13 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_07 for Mode: ALT4" line.long 0x74 "XBAR1_IN_SELECT_INPUT_34,XBAR1_IN_SELECT_INPUT_34 DAISY Register" bitfld.long 0x74 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_14 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_08 for Mode: ALT4" line.long 0x78 "XBAR1_IN_SELECT_INPUT_35,XBAR1_IN_SELECT_INPUT_35 DAISY Register" bitfld.long 0x78 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_EMC_B2_15 for Mode: ALT6,1: Selecting Pad: GPIO_DISP_B1_09 for Mode: ALT4" tree.end tree "IOMUXC_GPR" base ad:0x400E4000 group.long 0x0++0x17 line.long 0x0 "GPR0,GPR0 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x0 8. "SAI1_MCLK_DIR,SAI1_MCLK signal direction control" "0,1" newline bitfld.long 0x0 6.--7. "SAI1_MCLK3_SEL,SAI1 MCLK3 source select" "0,1,2,3" newline bitfld.long 0x0 3.--5. "SAI1_MCLK2_SEL,SAI1 MCLK2 source select" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "SAI1_MCLK1_SEL,SAI1 MCLK1 source select" "0,1,2,3,4,5,6,7" line.long 0x4 "GPR1,GPR1 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4 8. "SAI2_MCLK_DIR,SAI2_MCLK signal direction control" "0,1" newline bitfld.long 0x4 0.--1. "SAI2_MCLK3_SEL,SAI2 MCLK3 source select" "0,1,2,3" line.long 0x8 "GPR2,GPR2 General Purpose Register" bitfld.long 0x8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x8 9. "SAI4_MCLK_DIR,SAI4_MCLK signal direction control" "0,1" newline bitfld.long 0x8 8. "SAI3_MCLK_DIR,SAI3_MCLK signal direction control" "0,1" newline bitfld.long 0x8 0.--1. "SAI3_MCLK3_SEL,SAI3 MCLK3 source select" "0,1,2,3" line.long 0xC "GPR3,GPR3 General Purpose Register" bitfld.long 0xC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0xC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0xC 10. "MQS_OVERSAMPLE,Medium Quality Sound (MQS) Oversample" "0,1" newline bitfld.long 0xC 9. "MQS_EN,MQS enable" "0,1" newline bitfld.long 0xC 8. "MQS_SW_RST,MQS software reset" "0,1" newline hexmask.long.byte 0xC 0.--7. 1. "MQS_CLK_DIV,Divider ratio control for mclk from hmclk." line.long 0x10 "GPR4,GPR4 General Purpose Register" bitfld.long 0x10 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x10 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x10 3. "ENET_EVENT0IN_SEL,ENET ENET_1588_EVENT0_IN source select" "0,1" newline bitfld.long 0x10 2. "ENET_TIME_SEL,ENET master timer source select" "0,1" newline bitfld.long 0x10 1. "ENET_REF_CLK_DIR,ENET_REF_CLK direction control" "0,1" newline bitfld.long 0x10 0. "ENET_TX_CLK_SEL,ENET TX_CLK select" "0,1" line.long 0x14 "GPR5,GPR5 General Purpose Register" bitfld.long 0x14 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x14 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x14 4. "ENET1G_EVENT0IN_SEL,ENET1G ENET_1588_EVENT0_IN source select" "0,1" newline bitfld.long 0x14 3. "ENET1G_TIME_SEL,ENET1G master timer source select" "0,1" newline bitfld.long 0x14 2. "ENET1G_RGMII_EN,ENET1G RGMII TX clock output enable" "0,1" newline bitfld.long 0x14 1. "ENET1G_REF_CLK_DIR,ENET1G_REF_CLK direction control" "0,1" newline bitfld.long 0x14 0. "ENET1G_TX_CLK_SEL,ENET1G TX_CLK select" "0,1" group.long 0x1C++0x2F line.long 0x0 "GPR7,GPR7 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x0 0. "GINT,Global interrupt" "0,1" line.long 0x4 "GPR8,GPR8 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4 0. "WDOG1_MASK,WDOG1 timeout mask for WDOG_ANY" "0,1" line.long 0x8 "GPR9,GPR9 General Purpose Register" bitfld.long 0x8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x8 0. "WDOG2_MASK,WDOG2 timeout mask for WDOG_ANY" "0,1" line.long 0xC "GPR10,GPR10 General Purpose Register" bitfld.long 0xC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0xC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x10 "GPR11,GPR11 General Purpose Register" bitfld.long 0x10 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x10 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x14 "GPR12,GPR12 General Purpose Register" bitfld.long 0x14 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x14 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x14 11. "QTIMER1_TRM3_INPUT_SEL,QTIMER1 TMR3 input select" "0,1" newline bitfld.long 0x14 10. "QTIMER1_TRM2_INPUT_SEL,QTIMER1 TMR2 input select" "0,1" newline bitfld.long 0x14 9. "QTIMER1_TRM1_INPUT_SEL,QTIMER1 TMR1 input select" "0,1" newline bitfld.long 0x14 8. "QTIMER1_TRM0_INPUT_SEL,QTIMER1 TMR0 input select" "0,1" newline bitfld.long 0x14 0. "QTIMER1_TMR_CNTS_FREEZE,QTIMER1 timer counter freeze" "0,1" line.long 0x18 "GPR13,GPR13 General Purpose Register" bitfld.long 0x18 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x18 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x18 11. "QTIMER2_TRM3_INPUT_SEL,QTIMER2 TMR3 input select" "0,1" newline bitfld.long 0x18 10. "QTIMER2_TRM2_INPUT_SEL,QTIMER2 TMR2 input select" "0,1" newline bitfld.long 0x18 9. "QTIMER2_TRM1_INPUT_SEL,QTIMER2 TMR1 input select" "0,1" newline bitfld.long 0x18 8. "QTIMER2_TRM0_INPUT_SEL,QTIMER2 TMR0 input select" "0,1" newline bitfld.long 0x18 0. "QTIMER2_TMR_CNTS_FREEZE,QTIMER2 timer counter freeze" "0,1" line.long 0x1C "GPR14,GPR14 General Purpose Register" bitfld.long 0x1C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x1C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x1C 11. "QTIMER3_TRM3_INPUT_SEL,QTIMER3 TMR3 input select" "0,1" newline bitfld.long 0x1C 10. "QTIMER3_TRM2_INPUT_SEL,QTIMER3 TMR2 input select" "0,1" newline bitfld.long 0x1C 9. "QTIMER3_TRM1_INPUT_SEL,QTIMER3 TMR1 input select" "0,1" newline bitfld.long 0x1C 8. "QTIMER3_TRM0_INPUT_SEL,QTIMER3 TMR0 input select" "0,1" newline bitfld.long 0x1C 0. "QTIMER3_TMR_CNTS_FREEZE,QTIMER3 timer counter freeze" "0,1" line.long 0x20 "GPR15,GPR15 General Purpose Register" bitfld.long 0x20 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x20 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x20 11. "QTIMER4_TRM3_INPUT_SEL,QTIMER4 TMR3 input select" "0,1" newline bitfld.long 0x20 10. "QTIMER4_TRM2_INPUT_SEL,QTIMER4 TMR2 input select" "0,1" newline bitfld.long 0x20 9. "QTIMER4_TRM1_INPUT_SEL,QTIMER4 TMR1 input select" "0,1" newline bitfld.long 0x20 8. "QTIMER4_TRM0_INPUT_SEL,QTIMER4 TMR0 input select" "0,1" newline bitfld.long 0x20 0. "QTIMER4_TMR_CNTS_FREEZE,QTIMER4 timer counter freeze" "0,1" line.long 0x24 "GPR16,GPR16 General Purpose Register" bitfld.long 0x24 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x24 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x24 5. "M7_GPC_SLEEP_SEL,CM7 sleep request selection" "0,1" newline bitfld.long 0x24 3. "CM7_FORCE_HCLK_EN,CM7 platform AHB clock enable" "0,1" newline bitfld.long 0x24 2. "FLEXRAM_BANK_CFG_SEL,FlexRAM bank config source select" "0,1" line.long 0x28 "GPR17,GPR17 General Purpose Register" bitfld.long 0x28 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x28 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x28 0.--15. 1. "FLEXRAM_BANK_CFG_LOW,FlexRAM bank config value" line.long 0x2C "GPR18,GPR18 General Purpose Register" bitfld.long 0x2C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x2C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x2C 0.--15. 1. "FLEXRAM_BANK_CFG_HIGH,FlexRAM bank config value" group.long 0x50++0x8F line.long 0x0 "GPR20,GPR20 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x0 27. "IOMUXC_XBAR_DIR_SEL_31,IOMUXC XBAR_INOUT31 function direction select" "0,1" newline bitfld.long 0x0 26. "IOMUXC_XBAR_DIR_SEL_30,IOMUXC XBAR_INOUT30 function direction select" "0,1" newline bitfld.long 0x0 25. "IOMUXC_XBAR_DIR_SEL_29,IOMUXC XBAR_INOUT29 function direction select" "0,1" newline bitfld.long 0x0 24. "IOMUXC_XBAR_DIR_SEL_28,IOMUXC XBAR_INOUT28 function direction select" "0,1" newline bitfld.long 0x0 23. "IOMUXC_XBAR_DIR_SEL_27,IOMUXC XBAR_INOUT27 function direction select" "0,1" newline bitfld.long 0x0 22. "IOMUXC_XBAR_DIR_SEL_26,IOMUXC XBAR_INOUT26 function direction select" "0,1" newline bitfld.long 0x0 21. "IOMUXC_XBAR_DIR_SEL_25,IOMUXC XBAR_INOUT25 function direction select" "0,1" newline bitfld.long 0x0 20. "IOMUXC_XBAR_DIR_SEL_24,IOMUXC XBAR_INOUT24 function direction select" "0,1" newline bitfld.long 0x0 19. "IOMUXC_XBAR_DIR_SEL_23,IOMUXC XBAR_INOUT23 function direction select" "0,1" newline bitfld.long 0x0 18. "IOMUXC_XBAR_DIR_SEL_22,IOMUXC XBAR_INOUT22 function direction select" "0,1" newline bitfld.long 0x0 17. "IOMUXC_XBAR_DIR_SEL_21,IOMUXC XBAR_INOUT21 function direction select" "0,1" newline bitfld.long 0x0 16. "IOMUXC_XBAR_DIR_SEL_20,IOMUXC XBAR_INOUT20 function direction select" "0,1" newline bitfld.long 0x0 15. "IOMUXC_XBAR_DIR_SEL_19,IOMUXC XBAR_INOUT19 function direction select" "0,1" newline bitfld.long 0x0 14. "IOMUXC_XBAR_DIR_SEL_18,IOMUXC XBAR_INOUT18 function direction select" "0,1" newline bitfld.long 0x0 13. "IOMUXC_XBAR_DIR_SEL_17,IOMUXC XBAR_INOUT17 function direction select" "0,1" newline bitfld.long 0x0 12. "IOMUXC_XBAR_DIR_SEL_16,IOMUXC XBAR_INOUT16 function direction select" "0,1" newline bitfld.long 0x0 11. "IOMUXC_XBAR_DIR_SEL_15,IOMUXC XBAR_INOUT15 function direction select" "0,1" newline bitfld.long 0x0 10. "IOMUXC_XBAR_DIR_SEL_14,IOMUXC XBAR_INOUT14 function direction select" "0,1" newline bitfld.long 0x0 9. "IOMUXC_XBAR_DIR_SEL_13,IOMUXC XBAR_INOUT13 function direction select" "0,1" newline bitfld.long 0x0 8. "IOMUXC_XBAR_DIR_SEL_12,IOMUXC XBAR_INOUT12 function direction select" "0,1" newline bitfld.long 0x0 7. "IOMUXC_XBAR_DIR_SEL_11,IOMUXC XBAR_INOUT11 function direction select" "0,1" newline bitfld.long 0x0 6. "IOMUXC_XBAR_DIR_SEL_10,IOMUXC XBAR_INOUT10 function direction select" "0,1" newline bitfld.long 0x0 5. "IOMUXC_XBAR_DIR_SEL_9,IOMUXC XBAR_INOUT9 function direction select" "0,1" newline bitfld.long 0x0 4. "IOMUXC_XBAR_DIR_SEL_8,IOMUXC XBAR_INOUT8 function direction select" "0,1" newline bitfld.long 0x0 3. "IOMUXC_XBAR_DIR_SEL_7,IOMUXC XBAR_INOUT7 function direction select" "0,1" newline bitfld.long 0x0 2. "IOMUXC_XBAR_DIR_SEL_6,IOMUXC XBAR_INOUT6 function direction select" "0,1" newline bitfld.long 0x0 1. "IOMUXC_XBAR_DIR_SEL_5,IOMUXC XBAR_INOUT5 function direction select" "0,1" newline bitfld.long 0x0 0. "IOMUXC_XBAR_DIR_SEL_4,IOMUXC XBAR_INOUT4 function direction select" "0,1" line.long 0x4 "GPR21,GPR21 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4 10. "IOMUXC_XBAR_DIR_SEL_42,IOMUXC XBAR_INOUT42 function direction select" "0,1" newline bitfld.long 0x4 9. "IOMUXC_XBAR_DIR_SEL_41,IOMUXC XBAR_INOUT41 function direction select" "0,1" newline bitfld.long 0x4 8. "IOMUXC_XBAR_DIR_SEL_40,IOMUXC XBAR_INOUT40 function direction select" "0,1" newline bitfld.long 0x4 7. "IOMUXC_XBAR_DIR_SEL_39,IOMUXC XBAR_INOUT39 function direction select" "0,1" newline bitfld.long 0x4 6. "IOMUXC_XBAR_DIR_SEL_38,IOMUXC XBAR_INOUT38 function direction select" "0,1" newline bitfld.long 0x4 5. "IOMUXC_XBAR_DIR_SEL_37,IOMUXC XBAR_INOUT37 function direction select" "0,1" newline bitfld.long 0x4 4. "IOMUXC_XBAR_DIR_SEL_36,IOMUXC XBAR_INOUT36 function direction select" "0,1" newline bitfld.long 0x4 3. "IOMUXC_XBAR_DIR_SEL_35,IOMUXC XBAR_INOUT35 function direction select" "0,1" newline bitfld.long 0x4 2. "IOMUXC_XBAR_DIR_SEL_34,IOMUXC XBAR_INOUT34 function direction select" "0,1" newline bitfld.long 0x4 1. "IOMUXC_XBAR_DIR_SEL_33,IOMUXC XBAR_INOUT33 function direction select" "0,1" newline bitfld.long 0x4 0. "IOMUXC_XBAR_DIR_SEL_32,IOMUXC XBAR_INOUT32 function direction select" "0,1" line.long 0x8 "GPR22,GPR22 General Purpose Register" bitfld.long 0x8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x8 0. "REF_1M_CLK_GPT1,GPT1 1 MHz clock source select" "0,1" line.long 0xC "GPR23,GPR23 General Purpose Register" bitfld.long 0xC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0xC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0xC 2. "GPT2_CAPIN2_SEL,GPT2 input capture channel 2 source select" "0,1" newline bitfld.long 0xC 1. "GPT2_CAPIN1_SEL,GPT2 input capture channel 1 source select" "0,1" newline bitfld.long 0xC 0. "REF_1M_CLK_GPT2,GPT2 1 MHz clock source select" "0,1" line.long 0x10 "GPR24,GPR24 General Purpose Register" bitfld.long 0x10 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x10 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x10 1. "GPT3_CAPIN1_SEL,GPT3 input capture channel 1 source select" "0,1" newline bitfld.long 0x10 0. "REF_1M_CLK_GPT3,GPT3 1 MHz clock source select" "0,1" line.long 0x14 "GPR25,GPR25 General Purpose Register" bitfld.long 0x14 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x14 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x14 0. "REF_1M_CLK_GPT4,GPT4 1 MHz clock source select" "0,1" line.long 0x18 "GPR26,GPR26 General Purpose Register" bitfld.long 0x18 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x18 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x18 0. "REF_1M_CLK_GPT5,GPT5 1 MHz clock source select" "0,1" line.long 0x1C "GPR27,GPR27 General Purpose Register" bitfld.long 0x1C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x1C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x1C 0. "REF_1M_CLK_GPT6,GPT6 1 MHz clock source select" "0,1" line.long 0x20 "GPR28,GPR28 General Purpose Register" bitfld.long 0x20 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x20 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x20 13. "CACHE_USB,USB block cacheable attribute value of AXI transactions" "0,1" newline bitfld.long 0x20 7. "CACHE_ENET,ENET block cacheable attribute value of AXI transactions" "0,1" newline bitfld.long 0x20 5. "CACHE_ENET1G,no description available" "0,1" newline bitfld.long 0x20 1. "AWCACHE_USDHC,uSDHC block cacheable attribute value of AXI write transactions" "0,1" newline bitfld.long 0x20 0. "ARCACHE_USDHC,uSDHC block cacheable attribute value of AXI read transactions" "0,1" line.long 0x24 "GPR29,GPR29 General Purpose Register" bitfld.long 0x24 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x24 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x24 0. "USBPHY1_IPG_CLK_ACTIVE,USBPHY1 register access clock enable" "0,1" line.long 0x28 "GPR30,GPR30 General Purpose Register" bitfld.long 0x28 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x28 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x28 0. "USBPHY2_IPG_CLK_ACTIVE,USBPHY2 register access clock enable" "0,1" line.long 0x2C "GPR31,GPR31 General Purpose Register" bitfld.long 0x2C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x2C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x2C 2. "OCRAM_M7_CLK_GATING,OCRAM M7 clock gating enable" "0,1" newline bitfld.long 0x2C 0. "RMW2_WAIT_BVALID_CPL,OCRAM M7 RMW wait enable" "0,1" line.long 0x30 "GPR32,GPR32 General Purpose Register" bitfld.long 0x30 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x30 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x30 0. "RMW1_WAIT_BVALID_CPL,OCRAM1 RMW wait enable" "0,1" line.long 0x34 "GPR33,GPR33 General Purpose Register" bitfld.long 0x34 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x34 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x34 0. "RMW2_WAIT_BVALID_CPL,OCRAM2 RMW wait enable" "0,1" line.long 0x38 "GPR34,GPR34 General Purpose Register" bitfld.long 0x38 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x38 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x38 1. "FLEXSPI1_OTFAD_EN,FlexSPI1 OTFAD enable" "0,1" newline bitfld.long 0x38 0. "XECC_FLEXSPI1_WAIT_BVALID_CPL,XECC_FLEXSPI1 RMW wait enable" "0,1" line.long 0x3C "GPR35,GPR35 General Purpose Register" bitfld.long 0x3C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x3C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3C 1. "FLEXSPI2_OTFAD_EN,FlexSPI2 OTFAD enable" "0,1" newline bitfld.long 0x3C 0. "XECC_FLEXSPI2_WAIT_BVALID_CPL,XECC_FLEXSPI2 RMW wait enable" "0,1" line.long 0x40 "GPR36,GPR36 General Purpose Register" bitfld.long 0x40 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x40 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x40 0. "XECC_SEMC_WAIT_BVALID_CPL,XECC_SEMC RMW wait enable" "0,1" line.long 0x44 "GPR37,GPR37 General Purpose Register" bitfld.long 0x44 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x44 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x44 6. "M4_DBG_ACK_MASK,CM4 debug halt mask" "0,1" newline bitfld.long 0x44 5. "M7_DBG_ACK_MASK,CM7 debug halt mask" "0,1" newline bitfld.long 0x44 3. "EXC_MON,Exclusive monitor response select of illegal command" "0,1" newline bitfld.long 0x44 1. "DBG_EN,ARM invasive debug enable" "0,1" newline bitfld.long 0x44 0. "NIDEN,ARM non-secure (non-invasive) debug enable" "0,1" line.long 0x48 "GPR38,GPR38 General Purpose Register" bitfld.long 0x48 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x48 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x4C "GPR39,GPR39 General Purpose Register" bitfld.long 0x4C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x50 "GPR40,GPR40 General Purpose Register" bitfld.long 0x50 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x50 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x50 0.--15. 1. "GPIO_MUX2_GPIO_SEL_LOW,GPIO2 and CM7_GPIO2 share same IO MUX function GPIO_MUX2 selects one GPIO function." line.long 0x54 "GPR41,GPR41 General Purpose Register" bitfld.long 0x54 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x54 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x54 0.--15. 1. "GPIO_MUX2_GPIO_SEL_HIGH,GPIO2 and CM7_GPIO2 share same IO MUX function GPIO_MUX2 selects one GPIO function." line.long 0x58 "GPR42,GPR42 General Purpose Register" bitfld.long 0x58 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x58 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x58 0.--15. 1. "GPIO_MUX3_GPIO_SEL_LOW,GPIO3 and CM7_GPIO3 share same IO MUX function GPIO_MUX3 selects one GPIO function." line.long 0x5C "GPR43,GPR43 General Purpose Register" bitfld.long 0x5C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x5C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x5C 0.--15. 1. "GPIO_MUX3_GPIO_SEL_HIGH,GPIO3 and CM7_GPIO3 share same IO MUX function GPIO_MUX3 selects one GPIO function." line.long 0x60 "GPR44,GPR44 General Purpose Register" bitfld.long 0x60 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x60 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x64 "GPR45,GPR45 General Purpose Register" bitfld.long 0x64 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x64 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x68 "GPR46,GPR46 General Purpose Register" bitfld.long 0x68 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x68 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x6C "GPR47,GPR47 General Purpose Register" bitfld.long 0x6C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x6C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x70 "GPR48,GPR48 General Purpose Register" bitfld.long 0x70 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x70 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x74 "GPR49,GPR49 General Purpose Register" bitfld.long 0x74 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x74 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x78 "GPR50,GPR50 General Purpose Register" bitfld.long 0x78 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x78 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x78 0.--4. 1. "CAAM_IPS_MGR,CAAM manager processor identifier" line.long 0x7C "GPR51,GPR51 General Purpose Register" bitfld.long 0x7C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x7C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x7C 0. "M7_NMI_CLEAR,Clear CM7 NMI holding register" "0,1" line.long 0x80 "GPR52,GPR52 General Purpose Register" bitfld.long 0x80 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x80 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x84 "GPR53,GPR53 General Purpose Register" bitfld.long 0x84 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x84 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x88 "GPR54,GPR54 General Purpose Register" bitfld.long 0x88 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x88 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" line.long 0x8C "GPR55,GPR55 General Purpose Register" bitfld.long 0x8C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" group.long 0xEC++0x3 line.long 0x0 "GPR59,GPR59 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x0 12.--17. 1. "MIPI_CSI_S_PRG_RXHS_SETTLE,Bits used to program T_HS_SETTLE." newline bitfld.long 0x0 10.--11. "MIPI_CSI_RXLPRP,Programming bits that adjust the threshold voltage of LP-RX default setting 2'b01" "0,1,2,3" newline bitfld.long 0x0 8.--9. "MIPI_CSI_RXCDRP,Programming bits that adjust the threshold voltage of LP-CD default setting 2'b01" "0: 344mV,1: 325mV (Default),2: 307mV,3: Invalid" newline bitfld.long 0x0 6.--7. "MIPI_CSI_RX_RCAL,MIPI CSI PHY on-chip termination control bits" "0,1,2,3" newline bitfld.long 0x0 5. "MIPI_CSI_RX_ENABLE,Assert to enable MIPI CSI Receive Enable" "0,1" newline bitfld.long 0x0 4. "MIPI_CSI_PD_RX,Power Down input for MIPI CSI PHY." "0,1" newline bitfld.long 0x0 3. "MIPI_CSI_DDRCLK_EN,When high enables received DDR clock on CLK_DRXHS" "0,1" newline bitfld.long 0x0 2. "MIPI_CSI_CONT_CLK_MODE,Enables the slave clock lane feature to maintain HS reception state during continuous clock mode operation despite line glitches." "0,1" newline bitfld.long 0x0 1. "MIPI_CSI_SOFT_RST_N,MIPI CSI APB clock domain and User interface clock domain software reset bit" "0: Assert reset,1: De-assert reset" newline bitfld.long 0x0 0. "MIPI_CSI_AUTO_PD_EN,Powers down inactive lanes reported by CSI2X_CFG_NUM_LANES." "0,1" group.long 0xF8++0x3 line.long 0x0 "GPR62,GPR62 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x0 19. "MIPI_DSI_ESC_SOFT_RESET_N,MIPI DSI Escape clock domain software reset bit" "0: Assert reset,1: De-assert reset" newline bitfld.long 0x0 18. "MIPI_DSI_DPI_SOFT_RESET_N,MIPI DSI Pixel clock domain software reset bit" "0: Assert reset,1: De-assert reset" newline bitfld.long 0x0 17. "MIPI_DSI_BYTE_SOFT_RESET_N,MIPI DSI Byte clock domain software reset bit" "0: Assert reset,1: De-assert reset" newline bitfld.long 0x0 16. "MIPI_DSI_PCLK_SOFT_RESET_N,MIPI DSI APB clock domain software reset bit" "0: Assert reset,1: De-assert reset" newline bitfld.long 0x0 11.--13. "MIPI_DSI_TX_ULPS_ENABLE,DSI transmit ULPS mode enable" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 9.--10. "MIPI_DSI_TX_RCAL,MIPI DSI PHY on-chip termination control bits" "0,1,2,3" newline bitfld.long 0x0 6.--8. "MIPI_DSI_D1_TM,MIPI DSI Data Lane 1 triming bits" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 3.--5. "MIPI_DSI_D0_TM,MIPI DSI Data Lane 0 triming bits" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "MIPI_DSI_CLK_TM,MIPI DSI Clock Lane triming bits" "0,1,2,3,4,5,6,7" rgroup.long 0xFC++0x3 line.long 0x0 "GPR63,GPR63 General Purpose Register" bitfld.long 0x0 0.--2. "MIPI_DSI_TX_ULPS_ACTIVE,DSI transmit ULPS mode active flag" "0,1,2,3,4,5,6,7" group.long 0x100++0x2B line.long 0x0 "GPR64,GPR64 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x0 21.--24. 1. "GPIO_DISP1_NASRC,GPIO_DISP_B1 IO bank compensation codes" newline rbitfld.long 0x0 20. "GPIO_DISP1_COMPOK,GPIO_DISP_B1 IO bank compensation OK flag" "0,1" newline bitfld.long 0x0 14. "GPIO_DISP1_SUPLYDET_LATCH,GPIO_DISP_B1 IO bank power supply mode latch enable" "0,1" newline bitfld.long 0x0 13. "GPIO_DISP1_REFGEN_SLEEP,GPIO_DISP_B1 IO bank reference voltage generator cell sleep enable" "0,1" newline bitfld.long 0x0 12. "GPIO_DISP1_SELECT_NASRC,GPIO_DISP1_NASRC selection" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "GPIO_DISP1_RASRCN,GPIO_DISP_B1 IO bank's 4-bit NMOS compensation codes from core" newline hexmask.long.byte 0x0 4.--7. 1. "GPIO_DISP1_RASRCP,GPIO_DISP_B1 IO bank's 4-bit PMOS compensation codes from core" newline bitfld.long 0x0 3. "GPIO_DISP1_FASTFRZ_EN,Compensation code fast freeze" "0,1" newline bitfld.long 0x0 2. "GPIO_DISP1_COMPEN,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x0 1. "GPIO_DISP1_COMPTQ,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x0 0. "GPIO_DISP1_FREEZE,Compensation code freeze" "0,1" line.long 0x4 "GPR65,GPR65 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x4 21.--24. 1. "GPIO_EMC1_NASRC,GPIO_EMC_B1 IO bank compensation codes" newline rbitfld.long 0x4 20. "GPIO_EMC1_COMPOK,GPIO_EMC_B1 IO bank compensation OK flag" "0,1" newline bitfld.long 0x4 14. "GPIO_EMC1_SUPLYDET_LATCH,GPIO_EMC_B1 IO bank power supply mode latch enable" "0,1" newline bitfld.long 0x4 13. "GPIO_EMC1_REFGEN_SLEEP,GPIO_EMC_B1 IO bank reference voltage generator cell sleep enable" "0,1" newline bitfld.long 0x4 12. "GPIO_EMC1_SELECT_NASRC,GPIO_EMC1_NASRC selection" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "GPIO_EMC1_RASRCN,GPIO_EMC_B1 IO bank's 4-bit NMOS compensation codes from core" newline hexmask.long.byte 0x4 4.--7. 1. "GPIO_EMC1_RASRCP,GPIO_EMC_B1 IO bank's 4-bit PMOS compensation codes from core" newline bitfld.long 0x4 3. "GPIO_EMC1_FASTFRZ_EN,Compensation code fast freeze" "0,1" newline bitfld.long 0x4 2. "GPIO_EMC1_COMPEN,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x4 1. "GPIO_EMC1_COMPTQ,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x4 0. "GPIO_EMC1_FREEZE,Compensation code freeze" "0,1" line.long 0x8 "GPR66,GPR66 General Purpose Register" bitfld.long 0x8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x8 21.--24. 1. "GPIO_EMC2_NASRC,GPIO_EMC_B2 IO bank compensation codes" newline rbitfld.long 0x8 20. "GPIO_EMC2_COMPOK,GPIO_EMC_B2 IO bank compensation OK flag" "0,1" newline bitfld.long 0x8 14. "GPIO_EMC2_SUPLYDET_LATCH,GPIO_EMC_B2 IO bank power supply mode latch enable" "0,1" newline bitfld.long 0x8 13. "GPIO_EMC2_REFGEN_SLEEP,GPIO_EMC_B2 IO bank reference voltage generator cell sleep enable" "0,1" newline bitfld.long 0x8 12. "GPIO_EMC2_SELECT_NASRC,GPIO_EMC2_NASRC selection" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "GPIO_EMC2_RASRCN,GPIO_EMC_B2 IO bank's 4-bit NMOS compensation codes from core" newline hexmask.long.byte 0x8 4.--7. 1. "GPIO_EMC2_RASRCP,GPIO_EMC_B2 IO bank's 4-bit PMOS compensation codes from core" newline bitfld.long 0x8 3. "GPIO_EMC2_FASTFRZ_EN,Compensation code fast freeze" "0,1" newline bitfld.long 0x8 2. "GPIO_EMC2_COMPEN,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x8 1. "GPIO_EMC2_COMPTQ,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x8 0. "GPIO_EMC2_FREEZE,Compensation code freeze" "0,1" line.long 0xC "GPR67,GPR67 General Purpose Register" bitfld.long 0xC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0xC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0xC 21.--24. 1. "GPIO_SD1_NASRC,GPIO_SD_B1 IO bank compensation codes" newline rbitfld.long 0xC 20. "GPIO_SD1_COMPOK,GPIO_SD_B1 IO bank compensation OK flag" "0,1" newline bitfld.long 0xC 14. "GPIO_SD1_SUPLYDET_LATCH,GPIO_SD_B1 IO bank power supply mode latch enable" "0,1" newline bitfld.long 0xC 13. "GPIO_SD1_REFGEN_SLEEP,GPIO_SD_B1 IO bank reference voltage generator cell sleep enable" "0,1" newline bitfld.long 0xC 12. "GPIO_SD1_SELECT_NASRC,GPIO_SD1_NASRC selection" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "GPIO_SD1_RASRCN,GPIO_SD_B1 IO bank's 4-bit NMOS compensation codes from core" newline hexmask.long.byte 0xC 4.--7. 1. "GPIO_SD1_RASRCP,GPIO_SD_B1 IO bank's 4-bit PMOS compensation codes from core" newline bitfld.long 0xC 3. "GPIO_SD1_FASTFRZ_EN,Compensation code fast freeze" "0,1" newline bitfld.long 0xC 2. "GPIO_SD1_COMPEN,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0xC 1. "GPIO_SD1_COMPTQ,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0xC 0. "GPIO_SD1_FREEZE,Compensation code freeze" "0,1" line.long 0x10 "GPR68,GPR68 General Purpose Register" bitfld.long 0x10 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x10 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.byte 0x10 21.--24. 1. "GPIO_SD2_NASRC,GPIO_SD_B2 IO bank compensation codes" newline rbitfld.long 0x10 20. "GPIO_SD2_COMPOK,GPIO_SD_B2 IO bank compensation OK flag" "0,1" newline bitfld.long 0x10 14. "GPIO_SD2_SUPLYDET_LATCH,GPIO_SD_B2 IO bank power supply mode latch enable" "0,1" newline bitfld.long 0x10 13. "GPIO_SD2_REFGEN_SLEEP,GPIO_SD_B2 IO bank reference voltage generator cell sleep enable" "0,1" newline bitfld.long 0x10 12. "GPIO_SD2_SELECT_NASRC,GPIO_SD2_NASRC selection" "0,1" newline hexmask.long.byte 0x10 8.--11. 1. "GPIO_SD2_RASRCN,GPIO_SD_B2 IO bank's 4-bit NMOS compensation codes from core" newline hexmask.long.byte 0x10 4.--7. 1. "GPIO_SD2_RASRCP,GPIO_SD_B2 IO bank's 4-bit PMOS compensation codes from core" newline bitfld.long 0x10 3. "GPIO_SD2_FASTFRZ_EN,Compensation code fast freeze" "0,1" newline bitfld.long 0x10 2. "GPIO_SD2_COMPEN,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x10 1. "GPIO_SD2_COMPTQ,COMPEN and COMPTQ control the operating modes of the compensation cell" "0,1" newline bitfld.long 0x10 0. "GPIO_SD2_FREEZE,Compensation code freeze" "0,1" line.long 0x14 "GPR69,GPR69 General Purpose Register" bitfld.long 0x14 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x14 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x14 13. "SUPLYDET_SD2_SLEEP,GPIO_SD_B2 IO bank supply voltage detector sleep mode enable" "0,1" newline bitfld.long 0x14 12. "SUPLYDET_SD1_SLEEP,GPIO_SD_B1 IO bank supply voltage detector sleep mode enable" "0,1" newline bitfld.long 0x14 11. "SUPLYDET_EMC2_SLEEP,GPIO_EMC_B2 IO bank supply voltage detector sleep mode enable" "0,1" newline bitfld.long 0x14 10. "SUPLYDET_EMC1_SLEEP,GPIO_EMC_B1 IO bank supply voltage detector sleep mode enable" "0,1" newline bitfld.long 0x14 9. "SUPLYDET_DISP1_SLEEP,GPIO_DISP_B1 IO bank supply voltage detector sleep mode enable" "0,1" newline bitfld.long 0x14 8. "GPIO_AD1_LOW_RANGE,GPIO_LPSR IO bank supply voltage range selection for GPIO_AD_18 to GPIO_AD_35" "0,1" newline bitfld.long 0x14 7. "GPIO_AD1_HIGH_RANGE,GPIO_LPSR IO bank supply voltage range selection for GPIO_AD_18 to GPIO_AD_35" "0,1" newline bitfld.long 0x14 5. "GPIO_AD0_LOW_RANGE,GPIO_AD IO bank supply voltage range selection for GPIO_AD_00 to GPIO_AD_17" "0,1" newline bitfld.long 0x14 4. "GPIO_AD0_HIGH_RANGE,GPIO_AD IO bank supply voltage range selection for GPIO_AD_00 to GPIO_AD_17" "0,1" newline bitfld.long 0x14 2. "GPIO_DISP2_LOW_RANGE,GPIO_DISP_B2 IO bank supply voltage range selection" "0,1" newline bitfld.long 0x14 1. "GPIO_DISP2_HIGH_RANGE,GPIO_DISP_B2 IO bank supply voltage range selection" "0,1" line.long 0x18 "GPR70,GPR70 General Purpose Register" bitfld.long 0x18 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x18 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x18 26. "FLEXSPI2_STOP_REQ,FLEXSPI2 stop request" "0,1" newline bitfld.long 0x18 25. "FLEXSPI2_IPG_DOZE,FLEXSPI2 doze mode" "0,1" newline bitfld.long 0x18 24. "FLEXSPI1_STOP_REQ,FLEXSPI1 stop request" "0,1" newline bitfld.long 0x18 23. "FLEXSPI1_IPG_DOZE,FLEXSPI1 doze mode" "0,1" newline bitfld.long 0x18 22. "FLEXIO2_IPG_DOZE,FLEXIO2 doze mode" "0,1" newline bitfld.long 0x18 21. "FLEXIO1_IPG_DOZE,FLEXIO2 doze mode" "0,1" newline bitfld.long 0x18 20. "ENET1G_STOP_REQ,ENET1G stop request" "0,1" newline bitfld.long 0x18 19. "ENET1G_IPG_DOZE,ENET1G doze mode" "0,1" newline bitfld.long 0x18 18. "ENET_STOP_REQ,ENET stop request" "0,1" newline bitfld.long 0x18 17. "ENET_IPG_DOZE,ENET doze mode" "0,1" newline bitfld.long 0x18 16. "EDMA_LPSR_STOP_REQ,EDMA_LPSR stop request" "0,1" newline bitfld.long 0x18 15. "EDMA_STOP_REQ,EDMA stop request" "0,1" newline bitfld.long 0x18 13. "CAN3_STOP_REQ,CAN3 stop request" "0,1" newline bitfld.long 0x18 12. "CAN3_IPG_DOZE,CAN3 doze mode" "0,1" newline bitfld.long 0x18 11. "CAN2_STOP_REQ,CAN2 stop request" "0,1" newline bitfld.long 0x18 10. "CAN2_IPG_DOZE,CAN2 doze mode" "0,1" newline bitfld.long 0x18 9. "CAN1_STOP_REQ,CAN1 stop request" "0,1" newline bitfld.long 0x18 8. "CAN1_IPG_DOZE,CAN1 doze mode" "0,1" newline bitfld.long 0x18 7. "CAAM_STOP_REQ,CAAM stop request" "0,1" newline bitfld.long 0x18 6. "CAAM_IPG_DOZE,CAN3 doze mode" "0,1" newline bitfld.long 0x18 5. "ADC2_IPG_STOP_MODE,ADC2 stop mode selection cannot change when ADC2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x18 4. "ADC2_STOP_REQ,ADC2 stop request" "0,1" newline bitfld.long 0x18 3. "ADC2_IPG_DOZE,ADC2 doze mode" "0,1" newline bitfld.long 0x18 2. "ADC1_IPG_STOP_MODE,ADC1 stop mode selection cannot change when ADC1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x18 1. "ADC1_STOP_REQ,ADC1 stop request" "0,1" newline bitfld.long 0x18 0. "ADC1_IPG_DOZE,ADC1 doze mode" "0,1" line.long 0x1C "GPR71,GPR71 General Purpose Register" bitfld.long 0x1C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x1C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x1C 26. "LPSPI1_IPG_STOP_MODE,LPSPI1 stop mode selection cannot change when LPSPI1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 25. "LPSPI1_STOP_REQ,LPSPI1 stop request" "0,1" newline bitfld.long 0x1C 24. "LPSPI1_IPG_DOZE,LPSPI1 doze mode" "0,1" newline bitfld.long 0x1C 23. "LPI2C6_IPG_STOP_MODE,LPI2C6 stop mode selection cannot change when LPI2C6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 22. "LPI2C6_STOP_REQ,LPI2C6 stop request" "0,1" newline bitfld.long 0x1C 21. "LPI2C6_IPG_DOZE,LPI2C6 doze mode" "0,1" newline bitfld.long 0x1C 20. "LPI2C5_IPG_STOP_MODE,LPI2C5 stop mode selection cannot change when LPI2C5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 19. "LPI2C5_STOP_REQ,LPI2C5 stop request" "0,1" newline bitfld.long 0x1C 18. "LPI2C5_IPG_DOZE,LPI2C5 doze mode" "0,1" newline bitfld.long 0x1C 17. "LPI2C4_IPG_STOP_MODE,LPI2C4 stop mode selection cannot change when LPI2C4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 16. "LPI2C4_STOP_REQ,LPI2C4 stop request" "0,1" newline bitfld.long 0x1C 15. "LPI2C4_IPG_DOZE,LPI2C4 doze mode" "0,1" newline bitfld.long 0x1C 14. "LPI2C3_IPG_STOP_MODE,LPI2C3 stop mode selection cannot change when LPI2C3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 13. "LPI2C3_STOP_REQ,LPI2C3 stop request" "0,1" newline bitfld.long 0x1C 12. "LPI2C3_IPG_DOZE,LPI2C3 doze mode" "0,1" newline bitfld.long 0x1C 11. "LPI2C2_IPG_STOP_MODE,LPI2C2 stop mode selection cannot change when LPI2C2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 10. "LPI2C2_STOP_REQ,LPI2C2 stop request" "0,1" newline bitfld.long 0x1C 9. "LPI2C2_IPG_DOZE,LPI2C2 doze mode" "0,1" newline bitfld.long 0x1C 8. "LPI2C1_IPG_STOP_MODE,LPI2C1 stop mode selection cannot change when LPI2C1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x1C 7. "LPI2C1_STOP_REQ,LPI2C1 stop request" "0,1" newline bitfld.long 0x1C 6. "LPI2C1_IPG_DOZE,LPI2C1 doze mode" "0,1" newline bitfld.long 0x1C 5. "GPT6_IPG_DOZE,GPT6 doze mode" "0,1" newline bitfld.long 0x1C 4. "GPT5_IPG_DOZE,GPT5 doze mode" "0,1" newline bitfld.long 0x1C 3. "GPT4_IPG_DOZE,GPT4 doze mode" "0,1" newline bitfld.long 0x1C 2. "GPT3_IPG_DOZE,GPT3 doze mode" "0,1" newline bitfld.long 0x1C 1. "GPT2_IPG_DOZE,GPT2 doze mode" "0,1" newline bitfld.long 0x1C 0. "GPT1_IPG_DOZE,GPT1 doze mode" "0,1" line.long 0x20 "GPR72,GPR72 General Purpose Register" bitfld.long 0x20 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x20 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x20 26. "LPUART4_IPG_STOP_MODE,LPUART4 stop mode selection cannot change when LPUART4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 25. "LPUART4_STOP_REQ,LPUART4 stop request" "0,1" newline bitfld.long 0x20 24. "LPUART4_IPG_DOZE,LPUART4 doze mode" "0,1" newline bitfld.long 0x20 23. "LPUART3_IPG_STOP_MODE,LPUART3 stop mode selection cannot change when LPUART3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 22. "LPUART3_STOP_REQ,LPUART3 stop request" "0,1" newline bitfld.long 0x20 21. "LPUART3_IPG_DOZE,LPUART3 doze mode" "0,1" newline bitfld.long 0x20 20. "LPUART2_IPG_STOP_MODE,LPUART2 stop mode selection cannot change when LPUART2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 19. "LPUART2_STOP_REQ,LPUART2 stop request" "0,1" newline bitfld.long 0x20 18. "LPUART2_IPG_DOZE,LPUART2 doze mode" "0,1" newline bitfld.long 0x20 17. "LPUART1_IPG_STOP_MODE,LPUART1 stop mode selection cannot change when LPUART1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 16. "LPUART1_STOP_REQ,LPUART1 stop request" "0,1" newline bitfld.long 0x20 15. "LPUART1_IPG_DOZE,LPUART1 doze mode" "0,1" newline bitfld.long 0x20 14. "LPSPI6_IPG_STOP_MODE,LPSPI6 stop mode selection cannot change when LPSPI6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 13. "LPSPI6_STOP_REQ,LPSPI6 stop request" "0,1" newline bitfld.long 0x20 12. "LPSPI6_IPG_DOZE,LPSPI6 doze mode" "0,1" newline bitfld.long 0x20 11. "LPSPI5_IPG_STOP_MODE,LPSPI5 stop mode selection cannot change when LPSPI5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 10. "LPSPI5_STOP_REQ,LPSPI5 stop request" "0,1" newline bitfld.long 0x20 9. "LPSPI5_IPG_DOZE,LPSPI5 doze mode" "0,1" newline bitfld.long 0x20 8. "LPSPI4_IPG_STOP_MODE,LPSPI4 stop mode selection cannot change when LPSPI4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 7. "LPSPI4_STOP_REQ,LPSPI4 stop request" "0,1" newline bitfld.long 0x20 6. "LPSPI4_IPG_DOZE,LPSPI4 doze mode" "0,1" newline bitfld.long 0x20 5. "LPSPI3_IPG_STOP_MODE,LPSPI3 stop mode selection cannot change when LPSPI3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 4. "LPSPI3_STOP_REQ,LPSPI3 stop request" "0,1" newline bitfld.long 0x20 3. "LPSPI3_IPG_DOZE,LPSPI3 doze mode" "0,1" newline bitfld.long 0x20 2. "LPSPI2_IPG_STOP_MODE,LPSPI2 stop mode selection cannot change when LPSPI2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x20 1. "LPSPI2_STOP_REQ,LPSPI2 stop request" "0,1" newline bitfld.long 0x20 0. "LPSPI2_IPG_DOZE,LPSPI2 doze mode" "0,1" line.long 0x24 "GPR73,GPR73 General Purpose Register" bitfld.long 0x24 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x24 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x24 26. "MIC_IPG_STOP_MODE,MIC stop mode selection cannot change when MIC_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 25. "MIC_STOP_REQ,MIC stop request" "0,1" newline bitfld.long 0x24 24. "MIC_IPG_DOZE,MIC doze mode" "0,1" newline bitfld.long 0x24 23. "LPUART12_IPG_STOP_MODE,LPUART12 stop mode selection cannot change when LPUART12_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 22. "LPUART12_STOP_REQ,LPUART12 stop request" "0,1" newline bitfld.long 0x24 21. "LPUART12_IPG_DOZE,LPUART12 doze mode" "0,1" newline bitfld.long 0x24 20. "LPUART11_IPG_STOP_MODE,LPUART11 stop mode selection cannot change when LPUART11_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 19. "LPUART11_STOP_REQ,LPUART11 stop request" "0,1" newline bitfld.long 0x24 18. "LPUART11_IPG_DOZE,LPUART11 doze mode" "0,1" newline bitfld.long 0x24 17. "LPUART10_IPG_STOP_MODE,LPUART10 stop mode selection cannot change when LPUART10_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 16. "LPUART10_STOP_REQ,LPUART10 stop request" "0,1" newline bitfld.long 0x24 15. "LPUART10_IPG_DOZE,LPUART10 doze mode" "0,1" newline bitfld.long 0x24 14. "LPUART9_IPG_STOP_MODE,LPUART9 stop mode selection cannot change when LPUART9_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 13. "LPUART9_STOP_REQ,LPUART9 stop request" "0,1" newline bitfld.long 0x24 12. "LPUART9_IPG_DOZE,LPUART9 doze mode" "0,1" newline bitfld.long 0x24 11. "LPUART8_IPG_STOP_MODE,LPUART8 stop mode selection cannot change when LPUART8_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 10. "LPUART8_STOP_REQ,LPUART8 stop request" "0,1" newline bitfld.long 0x24 9. "LPUART8_IPG_DOZE,LPUART8 doze mode" "0,1" newline bitfld.long 0x24 8. "LPUART7_IPG_STOP_MODE,LPUART7 stop mode selection cannot change when LPUART7_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 7. "LPUART7_STOP_REQ,LPUART7 stop request" "0,1" newline bitfld.long 0x24 6. "LPUART7_IPG_DOZE,LPUART7 doze mode" "0,1" newline bitfld.long 0x24 5. "LPUART6_IPG_STOP_MODE,LPUART6 stop mode selection cannot change when LPUART6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 4. "LPUART6_STOP_REQ,LPUART6 stop request" "0,1" newline bitfld.long 0x24 3. "LPUART6_IPG_DOZE,LPUART6 doze mode" "0,1" newline bitfld.long 0x24 2. "LPUART5_IPG_STOP_MODE,LPUART5 stop mode selection cannot change when LPUART5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x24 1. "LPUART5_STOP_REQ,LPUART5 stop request" "0,1" newline bitfld.long 0x24 0. "LPUART5_IPG_DOZE,LPUART5 doze mode" "0,1" line.long 0x28 "GPR74,GPR74 General Purpose Register" bitfld.long 0x28 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x28 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x28 17. "FLEXIO2_STOP_REQ_PER,FLEXIO2 peripheral clock domain stop request" "0,1" newline bitfld.long 0x28 16. "FLEXIO2_STOP_REQ_BUS,FLEXIO2 bus clock domain stop request" "0,1" newline bitfld.long 0x28 15. "FLEXIO1_STOP_REQ_PER,FLEXIO1 peripheral clock domain stop request" "0,1" newline bitfld.long 0x28 14. "FLEXIO1_STOP_REQ_BUS,FLEXIO1 bus clock domain stop request" "0,1" newline bitfld.long 0x28 13. "SAI4_STOP_REQ,SAI4 stop request" "0,1" newline bitfld.long 0x28 12. "SAI3_STOP_REQ,SAI3 stop request" "0,1" newline bitfld.long 0x28 11. "SAI2_STOP_REQ,SAI2 stop request" "0,1" newline bitfld.long 0x28 10. "SAI1_STOP_REQ,SAI1 stop request" "0,1" newline bitfld.long 0x28 9. "WDOG2_IPG_DOZE,WDOG2 doze mode" "0,1" newline bitfld.long 0x28 8. "WDOG1_IPG_DOZE,WDOG1 doze mode" "0,1" newline bitfld.long 0x28 7. "SNVS_HP_STOP_REQ,SNVS_HP stop request" "0,1" newline bitfld.long 0x28 6. "SNVS_HP_IPG_DOZE,SNVS_HP doze mode" "0,1" newline bitfld.long 0x28 5. "SIM2_IPG_DOZE,SIM2 doze mode" "0,1" newline bitfld.long 0x28 4. "SIM1_IPG_DOZE,SIM1 doze mode" "0,1" newline bitfld.long 0x28 3. "SEMC_STOP_REQ,SEMC stop request" "0,1" newline bitfld.long 0x28 2. "PIT2_STOP_REQ,PIT2 stop request" "0,1" newline bitfld.long 0x28 1. "PIT1_STOP_REQ,PIT1 stop request" "0,1" rgroup.long 0x12C++0x7 line.long 0x0 "GPR75,GPR75 General Purpose Register" bitfld.long 0x0 31. "LPUART8_STOP_ACK,LPUART8 stop acknowledge" "0,1" newline bitfld.long 0x0 30. "LPUART7_STOP_ACK,LPUART7 stop acknowledge" "0,1" newline bitfld.long 0x0 29. "LPUART6_STOP_ACK,LPUART6 stop acknowledge" "0,1" newline bitfld.long 0x0 28. "LPUART5_STOP_ACK,LPUART5 stop acknowledge" "0,1" newline bitfld.long 0x0 27. "LPUART4_STOP_ACK,LPUART4 stop acknowledge" "0,1" newline bitfld.long 0x0 26. "LPUART3_STOP_ACK,LPUART3 stop acknowledge" "0,1" newline bitfld.long 0x0 25. "LPUART2_STOP_ACK,LPUART2 stop acknowledge" "0,1" newline bitfld.long 0x0 24. "LPUART1_STOP_ACK,LPUART1 stop acknowledge" "0,1" newline bitfld.long 0x0 23. "LPSPI6_STOP_ACK,LPSPI6 stop acknowledge" "0,1" newline bitfld.long 0x0 22. "LPSPI5_STOP_ACK,LPSPI5 stop acknowledge" "0,1" newline bitfld.long 0x0 21. "LPSPI4_STOP_ACK,LPSPI4 stop acknowledge" "0,1" newline bitfld.long 0x0 20. "LPSPI3_STOP_ACK,LPSPI3 stop acknowledge" "0,1" newline bitfld.long 0x0 19. "LPSPI2_STOP_ACK,LPSPI2 stop acknowledge" "0,1" newline bitfld.long 0x0 18. "LPSPI1_STOP_ACK,LPSPI1 stop acknowledge" "0,1" newline bitfld.long 0x0 17. "LPI2C6_STOP_ACK,LPI2C6 stop acknowledge" "0,1" newline bitfld.long 0x0 16. "LPI2C5_STOP_ACK,LPI2C5 stop acknowledge" "0,1" newline bitfld.long 0x0 15. "LPI2C4_STOP_ACK,LPI2C4 stop acknowledge" "0,1" newline bitfld.long 0x0 14. "LPI2C3_STOP_ACK,LPI2C3 stop acknowledge" "0,1" newline bitfld.long 0x0 13. "LPI2C2_STOP_ACK,LPI2C2 stop acknowledge" "0,1" newline bitfld.long 0x0 12. "LPI2C1_STOP_ACK,LPI2C1 stop acknowledge" "0,1" newline bitfld.long 0x0 11. "FLEXSPI2_STOP_ACK,FLEXSPI2 stop acknowledge" "0,1" newline bitfld.long 0x0 10. "FLEXSPI1_STOP_ACK,FLEXSPI1 stop acknowledge" "0,1" newline bitfld.long 0x0 9. "ENET1G_STOP_ACK,ENET1G stop acknowledge" "0,1" newline bitfld.long 0x0 8. "ENET_STOP_ACK,ENET stop acknowledge" "0,1" newline bitfld.long 0x0 7. "EDMA_LPSR_STOP_ACK,EDMA_LPSR stop acknowledge" "0,1" newline bitfld.long 0x0 6. "EDMA_STOP_ACK,EDMA stop acknowledge" "0,1" newline bitfld.long 0x0 5. "CAN3_STOP_ACK,CAN3 stop acknowledge" "0,1" newline bitfld.long 0x0 4. "CAN2_STOP_ACK,CAN2 stop acknowledge" "0,1" newline bitfld.long 0x0 3. "CAN1_STOP_ACK,CAN1 stop acknowledge" "0,1" newline bitfld.long 0x0 2. "CAAM_STOP_ACK,CAAM stop acknowledge" "0,1" newline bitfld.long 0x0 1. "ADC2_STOP_ACK,ADC2 stop acknowledge" "0,1" newline bitfld.long 0x0 0. "ADC1_STOP_ACK,ADC1 stop acknowledge" "0,1" line.long 0x4 "GPR76,GPR76 General Purpose Register" bitfld.long 0x4 16. "FLEXIO2_STOP_ACK_PER,FLEXIO2 stop acknowledge of peripheral clock domain" "0,1" newline bitfld.long 0x4 15. "FLEXIO2_STOP_ACK_BUS,FLEXIO2 stop acknowledge of bus clock domain" "0,1" newline bitfld.long 0x4 14. "FLEXIO1_STOP_ACK_PER,FLEXIO1 stop acknowledge of peripheral clock domain" "0,1" newline bitfld.long 0x4 13. "FLEXIO1_STOP_ACK_BUS,FLEXIO1 stop acknowledge of bus clock domain" "0,1" newline bitfld.long 0x4 12. "SAI4_STOP_ACK,SAI4 stop acknowledge" "0,1" newline bitfld.long 0x4 11. "SAI3_STOP_ACK,SAI3 stop acknowledge" "0,1" newline bitfld.long 0x4 10. "SAI2_STOP_ACK,SAI2 stop acknowledge" "0,1" newline bitfld.long 0x4 9. "SAI1_STOP_ACK,SAI1 stop acknowledge" "0,1" newline bitfld.long 0x4 8. "SNVS_HP_STOP_ACK,SNVS_HP stop acknowledge" "0,1" newline bitfld.long 0x4 7. "SEMC_STOP_ACK,SEMC stop acknowledge" "0,1" newline bitfld.long 0x4 6. "PIT2_STOP_ACK,PIT2 stop acknowledge" "0,1" newline bitfld.long 0x4 5. "PIT1_STOP_ACK,PIT1 stop acknowledge" "0,1" newline bitfld.long 0x4 4. "MIC_STOP_ACK,MIC stop acknowledge" "0,1" newline bitfld.long 0x4 3. "LPUART12_STOP_ACK,LPUART12 stop acknowledge" "0,1" newline bitfld.long 0x4 2. "LPUART11_STOP_ACK,LPUART11 stop acknowledge" "0,1" newline bitfld.long 0x4 1. "LPUART10_STOP_ACK,LPUART10 stop acknowledge" "0,1" newline bitfld.long 0x4 0. "LPUART9_STOP_ACK,LPUART9 stop acknowledge" "0,1" tree.end tree "IOMUXC_LPSR" base ad:0x40C08000 group.long 0x0++0xDF line.long 0x0 "SW_MUX_CTL_PAD_GPIO_LPSR_00,SW_MUX_CTL_PAD_GPIO_LPSR_00 SW MUX Control Register" bitfld.long 0x0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_00" hexmask.long.byte 0x0 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x4 "SW_MUX_CTL_PAD_GPIO_LPSR_01,SW_MUX_CTL_PAD_GPIO_LPSR_01 SW MUX Control Register" bitfld.long 0x4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_01" hexmask.long.byte 0x4 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x8 "SW_MUX_CTL_PAD_GPIO_LPSR_02,SW_MUX_CTL_PAD_GPIO_LPSR_02 SW MUX Control Register" bitfld.long 0x8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_02" hexmask.long.byte 0x8 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0xC "SW_MUX_CTL_PAD_GPIO_LPSR_03,SW_MUX_CTL_PAD_GPIO_LPSR_03 SW MUX Control Register" bitfld.long 0xC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_03" hexmask.long.byte 0xC 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x10 "SW_MUX_CTL_PAD_GPIO_LPSR_04,SW_MUX_CTL_PAD_GPIO_LPSR_04 SW MUX Control Register" bitfld.long 0x10 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_04" hexmask.long.byte 0x10 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x14 "SW_MUX_CTL_PAD_GPIO_LPSR_05,SW_MUX_CTL_PAD_GPIO_LPSR_05 SW MUX Control Register" bitfld.long 0x14 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_05" hexmask.long.byte 0x14 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x18 "SW_MUX_CTL_PAD_GPIO_LPSR_06,SW_MUX_CTL_PAD_GPIO_LPSR_06 SW MUX Control Register" bitfld.long 0x18 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_06" hexmask.long.byte 0x18 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x1C "SW_MUX_CTL_PAD_GPIO_LPSR_07,SW_MUX_CTL_PAD_GPIO_LPSR_07 SW MUX Control Register" bitfld.long 0x1C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_07" hexmask.long.byte 0x1C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x20 "SW_MUX_CTL_PAD_GPIO_LPSR_08,SW_MUX_CTL_PAD_GPIO_LPSR_08 SW MUX Control Register" bitfld.long 0x20 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_08" hexmask.long.byte 0x20 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x24 "SW_MUX_CTL_PAD_GPIO_LPSR_09,SW_MUX_CTL_PAD_GPIO_LPSR_09 SW MUX Control Register" bitfld.long 0x24 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_09" hexmask.long.byte 0x24 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x28 "SW_MUX_CTL_PAD_GPIO_LPSR_10,SW_MUX_CTL_PAD_GPIO_LPSR_10 SW MUX Control Register" bitfld.long 0x28 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_10" hexmask.long.byte 0x28 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x2C "SW_MUX_CTL_PAD_GPIO_LPSR_11,SW_MUX_CTL_PAD_GPIO_LPSR_11 SW MUX Control Register" bitfld.long 0x2C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_11" hexmask.long.byte 0x2C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x30 "SW_MUX_CTL_PAD_GPIO_LPSR_12,SW_MUX_CTL_PAD_GPIO_LPSR_12 SW MUX Control Register" bitfld.long 0x30 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_12" hexmask.long.byte 0x30 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x34 "SW_MUX_CTL_PAD_GPIO_LPSR_13,SW_MUX_CTL_PAD_GPIO_LPSR_13 SW MUX Control Register" bitfld.long 0x34 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_13" hexmask.long.byte 0x34 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x38 "SW_MUX_CTL_PAD_GPIO_LPSR_14,SW_MUX_CTL_PAD_GPIO_LPSR_14 SW MUX Control Register" bitfld.long 0x38 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_14" hexmask.long.byte 0x38 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x3C "SW_MUX_CTL_PAD_GPIO_LPSR_15,SW_MUX_CTL_PAD_GPIO_LPSR_15 SW MUX Control Register" bitfld.long 0x3C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_LPSR_15" hexmask.long.byte 0x3C 0.--3. 1. "MUX_MODE,MUX Mode Select Field." line.long 0x40 "SW_PAD_CTL_PAD_GPIO_LPSR_00,SW_PAD_CTL_PAD_GPIO_LPSR_00 SW PAD Control Register" bitfld.long 0x40 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x40 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x40 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x40 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x40 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x40 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x40 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x44 "SW_PAD_CTL_PAD_GPIO_LPSR_01,SW_PAD_CTL_PAD_GPIO_LPSR_01 SW PAD Control Register" bitfld.long 0x44 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x44 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x44 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x44 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x44 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x44 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x44 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x48 "SW_PAD_CTL_PAD_GPIO_LPSR_02,SW_PAD_CTL_PAD_GPIO_LPSR_02 SW PAD Control Register" bitfld.long 0x48 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x48 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x48 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x48 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x48 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x48 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x48 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x4C "SW_PAD_CTL_PAD_GPIO_LPSR_03,SW_PAD_CTL_PAD_GPIO_LPSR_03 SW PAD Control Register" bitfld.long 0x4C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x4C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4C 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x4C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x4C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x4C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x4C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x50 "SW_PAD_CTL_PAD_GPIO_LPSR_04,SW_PAD_CTL_PAD_GPIO_LPSR_04 SW PAD Control Register" bitfld.long 0x50 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x50 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x50 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x50 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x50 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x50 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x50 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x54 "SW_PAD_CTL_PAD_GPIO_LPSR_05,SW_PAD_CTL_PAD_GPIO_LPSR_05 SW PAD Control Register" bitfld.long 0x54 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x54 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x54 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x54 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x54 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x54 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x54 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x58 "SW_PAD_CTL_PAD_GPIO_LPSR_06,SW_PAD_CTL_PAD_GPIO_LPSR_06 SW PAD Control Register" bitfld.long 0x58 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x58 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x58 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x58 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x58 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x58 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x58 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x5C "SW_PAD_CTL_PAD_GPIO_LPSR_07,SW_PAD_CTL_PAD_GPIO_LPSR_07 SW PAD Control Register" bitfld.long 0x5C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x5C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x5C 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x5C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x5C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x5C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x5C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x60 "SW_PAD_CTL_PAD_GPIO_LPSR_08,SW_PAD_CTL_PAD_GPIO_LPSR_08 SW PAD Control Register" bitfld.long 0x60 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x60 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x60 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x60 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x60 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x60 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x60 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x64 "SW_PAD_CTL_PAD_GPIO_LPSR_09,SW_PAD_CTL_PAD_GPIO_LPSR_09 SW PAD Control Register" bitfld.long 0x64 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x64 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x64 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x64 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x64 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x64 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x64 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x68 "SW_PAD_CTL_PAD_GPIO_LPSR_10,SW_PAD_CTL_PAD_GPIO_LPSR_10 SW PAD Control Register" bitfld.long 0x68 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x68 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x68 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x68 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x68 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x68 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x68 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x6C "SW_PAD_CTL_PAD_GPIO_LPSR_11,SW_PAD_CTL_PAD_GPIO_LPSR_11 SW PAD Control Register" bitfld.long 0x6C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x6C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x6C 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x6C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x6C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x6C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x6C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x70 "SW_PAD_CTL_PAD_GPIO_LPSR_12,SW_PAD_CTL_PAD_GPIO_LPSR_12 SW PAD Control Register" bitfld.long 0x70 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x70 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x70 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x70 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x70 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x70 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x70 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x74 "SW_PAD_CTL_PAD_GPIO_LPSR_13,SW_PAD_CTL_PAD_GPIO_LPSR_13 SW PAD Control Register" bitfld.long 0x74 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x74 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x74 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x74 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x74 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x74 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x74 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x78 "SW_PAD_CTL_PAD_GPIO_LPSR_14,SW_PAD_CTL_PAD_GPIO_LPSR_14 SW PAD Control Register" bitfld.long 0x78 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x78 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x78 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x78 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x78 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x78 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x78 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x7C "SW_PAD_CTL_PAD_GPIO_LPSR_15,SW_PAD_CTL_PAD_GPIO_LPSR_15 SW PAD Control Register" bitfld.long 0x7C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x7C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x7C 5. "ODE_LPSR,Open Drain LPSR Field" "0: Disabled,1: Enabled" bitfld.long 0x7C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x7C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x7C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x7C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x80 "CAN3_IPP_IND_CANRX_SELECT_INPUT,CAN3_IPP_IND_CANRX_SELECT_INPUT DAISY Register" bitfld.long 0x80 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_01 for Mode: ALT0,1: Selecting Pad: GPIO_LPSR_07 for Mode: ALT6,2: Selecting Pad: GPIO_LPSR_09 for Mode: ALT1,?" line.long 0x84 "LPI2C5_IPP_IND_LPI2C_SCL_SELECT_INPUT,LPI2C5_IPP_IND_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0x84 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_05 for Mode: ALT0,1: Selecting Pad: GPIO_LPSR_09 for Mode: ALT6" line.long 0x88 "LPI2C5_IPP_IND_LPI2C_SDA_SELECT_INPUT,LPI2C5_IPP_IND_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0x88 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_04 for Mode: ALT0,1: Selecting Pad: GPIO_LPSR_08 for Mode: ALT6" line.long 0x8C "LPI2C6_IPP_IND_LPI2C_SCL_SELECT_INPUT,LPI2C6_IPP_IND_LPI2C_SCL_SELECT_INPUT DAISY Register" bitfld.long 0x8C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_07 for Mode: ALT0,1: Selecting Pad: GPIO_LPSR_11 for Mode: ALT2" line.long 0x90 "LPI2C6_IPP_IND_LPI2C_SDA_SELECT_INPUT,LPI2C6_IPP_IND_LPI2C_SDA_SELECT_INPUT DAISY Register" bitfld.long 0x90 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_06 for Mode: ALT0,1: Selecting Pad: GPIO_LPSR_10 for Mode: ALT2" line.long 0x94 "LPSPI5_IPP_IND_LPSPI_PCS_SELECT_INPUT_0,LPSPI5_IPP_IND_LPSPI_PCS_SELECT_INPUT_0 DAISY Register" bitfld.long 0x94 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_03 for Mode: ALT1,1: Selecting Pad: GPIO_LPSR_13 for Mode: ALT8" line.long 0x98 "LPSPI5_IPP_IND_LPSPI_SCK_SELECT_INPUT,LPSPI5_IPP_IND_LPSPI_SCK_SELECT_INPUT DAISY Register" bitfld.long 0x98 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_02 for Mode: ALT1,1: Selecting Pad: GPIO_LPSR_12 for Mode: ALT8" line.long 0x9C "LPSPI5_IPP_IND_LPSPI_SDI_SELECT_INPUT,LPSPI5_IPP_IND_LPSPI_SDI_SELECT_INPUT DAISY Register" bitfld.long 0x9C 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_05 for Mode: ALT1,1: Selecting Pad: GPIO_LPSR_15 for Mode: ALT8" line.long 0xA0 "LPSPI5_IPP_IND_LPSPI_SDO_SELECT_INPUT,LPSPI5_IPP_IND_LPSPI_SDO_SELECT_INPUT DAISY Register" bitfld.long 0xA0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_04 for Mode: ALT1,1: Selecting Pad: GPIO_LPSR_14 for Mode: ALT8" line.long 0xA4 "LPUART11_IPP_IND_LPUART_RXD_SELECT_INPUT,LPUART11_IPP_IND_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0xA4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_05 for Mode: ALT6,1: Selecting Pad: GPIO_LPSR_09 for Mode: ALT0" line.long 0xA8 "LPUART11_IPP_IND_LPUART_TXD_SELECT_INPUT,LPUART11_IPP_IND_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0xA8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_04 for Mode: ALT6,1: Selecting Pad: GPIO_LPSR_08 for Mode: ALT0" line.long 0xAC "LPUART12_IPP_IND_LPUART_RXD_SELECT_INPUT,LPUART12_IPP_IND_LPUART_RXD_SELECT_INPUT DAISY Register" bitfld.long 0xAC 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_01 for Mode: ALT6,1: Selecting Pad: GPIO_LPSR_07 for Mode: ALT3,2: Selecting Pad: GPIO_LPSR_11 for Mode: ALT8,?" line.long 0xB0 "LPUART12_IPP_IND_LPUART_TXD_SELECT_INPUT,LPUART12_IPP_IND_LPUART_TXD_SELECT_INPUT DAISY Register" bitfld.long 0xB0 0.--1. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_00 for Mode: ALT6,1: Selecting Pad: GPIO_LPSR_06 for Mode: ALT3,2: Selecting Pad: GPIO_LPSR_10 for Mode: ALT8,?" line.long 0xB4 "MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_0,MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_0 DAISY Register" bitfld.long 0xB4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_01 for Mode: ALT1,1: Selecting Pad: GPIO_LPSR_09 for Mode: ALT3" line.long 0xB8 "MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_1,MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_1 DAISY Register" bitfld.long 0xB8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_10 for Mode: ALT3,1: Selecting Pad: GPIO_LPSR_13 for Mode: ALT1" line.long 0xBC "MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_2,MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_2 DAISY Register" bitfld.long 0xBC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_11 for Mode: ALT3,1: Selecting Pad: GPIO_LPSR_14 for Mode: ALT1" line.long 0xC0 "MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_3,MIC_IPP_IND_MIC_PDM_BITSTREAM_SELECT_INPUT_3 DAISY Register" bitfld.long 0xC0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_12 for Mode: ALT3,1: Selecting Pad: GPIO_LPSR_15 for Mode: ALT1" line.long 0xC4 "NMI_GLUE_IPP_IND_NMI_SELECT_INPUT,NMI_GLUE_IPP_IND_NMI_SELECT_INPUT DAISY Register" bitfld.long 0xC4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_05 for Mode: ALT7,1: Selecting Pad: WAKEUP_DIG for Mode: ALT7" line.long 0xC8 "SAI4_IPG_CLK_SAI_MCLK_SELECT_INPUT,SAI4_IPG_CLK_SAI_MCLK_SELECT_INPUT DAISY Register" bitfld.long 0xC8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_00 for Mode: ALT7,1: Selecting Pad: GPIO_LPSR_05 for Mode: ALT2" line.long 0xCC "SAI4_IPP_IND_SAI_RXBCLK_SELECT_INPUT,SAI4_IPP_IND_SAI_RXBCLK_SELECT_INPUT DAISY Register" bitfld.long 0xCC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_07 for Mode: ALT2,1: Selecting Pad: GPIO_LPSR_14 for Mode: ALT7" line.long 0xD0 "SAI4_IPP_IND_SAI_RXDATA_SELECT_INPUT_0,SAI4_IPP_IND_SAI_RXDATA_SELECT_INPUT_0 DAISY Register" bitfld.long 0xD0 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_06 for Mode: ALT2,1: Selecting Pad: GPIO_LPSR_13 for Mode: ALT7" line.long 0xD4 "SAI4_IPP_IND_SAI_RXSYNC_SELECT_INPUT,SAI4_IPP_IND_SAI_RXSYNC_SELECT_INPUT DAISY Register" bitfld.long 0xD4 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_08 for Mode: ALT2,1: Selecting Pad: GPIO_LPSR_15 for Mode: ALT7" line.long 0xD8 "SAI4_IPP_IND_SAI_TXBCLK_SELECT_INPUT,SAI4_IPP_IND_SAI_TXBCLK_SELECT_INPUT DAISY Register" bitfld.long 0xD8 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_04 for Mode: ALT2,1: Selecting Pad: GPIO_LPSR_12 for Mode: ALT7" line.long 0xDC "SAI4_IPP_IND_SAI_TXSYNC_SELECT_INPUT,SAI4_IPP_IND_SAI_TXSYNC_SELECT_INPUT DAISY Register" bitfld.long 0xDC 0. "DAISY,Selecting Pads Involved in Daisy Chain." "0: Selecting Pad: GPIO_LPSR_03 for Mode: ALT2,1: Selecting Pad: GPIO_LPSR_10 for Mode: ALT7" tree.end tree "IOMUXC_LPSR_GPR" base ad:0x40C0C000 group.long 0x0++0x6B line.long 0x0 "GPR0,GPR0 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x0 3.--15. 1. "CM4_INIT_VTOR_LOW,CM4 Vector table offset value lower bits out of reset" line.long 0x4 "GPR1,GPR1 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline hexmask.long.word 0x4 0.--15. 1. "CM4_INIT_VTOR_HIGH,CM4 Vector table offset value higher bits out of reset" line.long 0x8 "GPR2,GPR2 General Purpose Register" hexmask.long 0x8 3.--31. 1. "APC_AC_R0_BOT,APC start address of memory region-0" newline bitfld.long 0x8 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0xC "GPR3,GPR3 General Purpose Register" hexmask.long 0xC 3.--31. 1. "APC_AC_R0_TOP,APC end address of memory region-0" newline bitfld.long 0xC 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x10 "GPR4,GPR4 General Purpose Register" hexmask.long 0x10 3.--31. 1. "APC_AC_R1_BOT,APC start address of memory region-1" newline bitfld.long 0x10 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x14 "GPR5,GPR5 General Purpose Register" hexmask.long 0x14 3.--31. 1. "APC_AC_R1_TOP,APC end address of memory region-1" newline bitfld.long 0x14 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x18 "GPR6,GPR6 General Purpose Register" hexmask.long 0x18 3.--31. 1. "APC_AC_R2_BOT,APC start address of memory region-2" newline bitfld.long 0x18 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x1C "GPR7,GPR7 General Purpose Register" hexmask.long 0x1C 3.--31. 1. "APC_AC_R2_TOP,APC end address of memory region-2" newline bitfld.long 0x1C 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x20 "GPR8,GPR8 General Purpose Register" hexmask.long 0x20 3.--31. 1. "APC_AC_R3_BOT,APC start address of memory region-3" newline bitfld.long 0x20 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x24 "GPR9,GPR9 General Purpose Register" hexmask.long 0x24 3.--31. 1. "APC_AC_R3_TOP,APC end address of memory region-3" newline bitfld.long 0x24 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x28 "GPR10,GPR10 General Purpose Register" hexmask.long 0x28 3.--31. 1. "APC_AC_R4_BOT,APC start address of memory region-4" newline bitfld.long 0x28 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x2C "GPR11,GPR11 General Purpose Register" hexmask.long 0x2C 3.--31. 1. "APC_AC_R4_TOP,APC end address of memory region-4" newline bitfld.long 0x2C 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x30 "GPR12,GPR12 General Purpose Register" hexmask.long 0x30 3.--31. 1. "APC_AC_R5_BOT,APC start address of memory region-5" newline bitfld.long 0x30 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x34 "GPR13,GPR13 General Purpose Register" hexmask.long 0x34 3.--31. 1. "APC_AC_R5_TOP,APC end address of memory region-5" newline bitfld.long 0x34 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x38 "GPR14,GPR14 General Purpose Register" hexmask.long 0x38 3.--31. 1. "APC_AC_R6_BOT,APC start address of memory region-6" newline bitfld.long 0x38 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x3C "GPR15,GPR15 General Purpose Register" hexmask.long 0x3C 3.--31. 1. "APC_AC_R6_TOP,APC end address of memory region-6" newline bitfld.long 0x3C 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x40 "GPR16,GPR16 General Purpose Register" hexmask.long 0x40 3.--31. 1. "APC_AC_R7_BOT,APC start address of memory region-7" newline bitfld.long 0x40 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x44 "GPR17,GPR17 General Purpose Register" hexmask.long 0x44 3.--31. 1. "APC_AC_R7_TOP,APC end address of memory region-7" newline bitfld.long 0x44 0. "LOCK,Lock the write to bit 31:1" "0: Write access to bit 31:1 is not blocked,1: Write access to bit 31:1 is blocked" line.long 0x48 "GPR18,GPR18 General Purpose Register" hexmask.long.word 0x48 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x48 4. "APC_R0_ENCRYPT_ENABLE,APC memory region-0 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x4C "GPR19,GPR19 General Purpose Register" hexmask.long.word 0x4C 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x4C 4. "APC_R1_ENCRYPT_ENABLE,APC memory region-1 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x50 "GPR20,GPR20 General Purpose Register" hexmask.long.word 0x50 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x50 4. "APC_R2_ENCRYPT_ENABLE,APC memory region-2 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x54 "GPR21,GPR21 General Purpose Register" hexmask.long.word 0x54 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x54 4. "APC_R3_ENCRYPT_ENABLE,APC memory region-3 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x58 "GPR22,GPR22 General Purpose Register" hexmask.long.word 0x58 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x58 4. "APC_R4_ENCRYPT_ENABLE,APC memory region-4 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x5C "GPR23,GPR23 General Purpose Register" hexmask.long.word 0x5C 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x5C 4. "APC_R5_ENCRYPT_ENABLE,APC memory region-5 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x60 "GPR24,GPR24 General Purpose Register" hexmask.long.word 0x60 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x60 4. "APC_R6_ENCRYPT_ENABLE,APC memory region-6 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x64 "GPR25,GPR25 General Purpose Register" hexmask.long.word 0x64 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline bitfld.long 0x64 5. "APC_VALID,APC global enable bit" "0: No effect,1: Enable encryption for GPRx[APC_x_ENCRYPT_ENABLE].." newline bitfld.long 0x64 4. "APC_R7_ENCRYPT_ENABLE,APC memory region-7 encryption enable" "0: No effect,1: Encryption enabled" line.long 0x68 "GPR26,GPR26 General Purpose Register" bitfld.long 0x68 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x68 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x68 25.--27. "FIELD_0,General purpose bits" "0,1,2,3,4,5,6,7" newline hexmask.long 0x68 0.--24. 1. "CM7_INIT_VTOR,Vector table offset register out of reset. See the ARM v7-M Architecture Reference Manual for more information about the vector table offset register (VTOR)." group.long 0x84++0x1B line.long 0x0 "GPR33,GPR33 General Purpose Register" bitfld.long 0x0 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x0 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x0 9. "USBPHY2_WAKEUP_IRQ_CLEAR,Clear USBPHY1 wakeup interrupt holding register" "0,1" newline bitfld.long 0x0 8. "USBPHY1_WAKEUP_IRQ_CLEAR,Clear USBPHY1 wakeup interrupt holding register" "0,1" newline bitfld.long 0x0 0. "M4_NMI_CLEAR,Clear CM4 NMI holding register" "0,1" line.long 0x4 "GPR34,GPR34 General Purpose Register" bitfld.long 0x4 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x4 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4 11. "SEC_ERR_RESP,Security error response enable" "0: OKEY response,1: SLVError (default)" newline bitfld.long 0x4 5. "M4_GPC_SLEEP_SEL,CM4 sleep request selection" "0: CM4 SLEEPDEEP is sent to GPC,1: CM4 SLEEPING is sent to GPC" newline bitfld.long 0x4 4. "M4_NMI_MASK,Mask CM4 NMI pin input" "0: NMI input from IO to CM4 is not blocked,1: NMI input from IO to CM4 is blocked" newline bitfld.long 0x4 3. "M7_NMI_MASK,Mask CM7 NMI pin input" "0: NMI input from IO to CM7 is not blocked,1: NMI input from IO to CM7 is blocked" newline bitfld.long 0x4 2. "GPIO_LPSR_LOW_RANGE,GPIO_LPSR IO bank supply voltage range selection" "0,1" newline bitfld.long 0x4 1. "GPIO_LPSR_HIGH_RANGE,GPIO_LPSR IO bank supply voltage range selection" "0,1" line.long 0x8 "GPR35,GPR35 General Purpose Register" bitfld.long 0x8 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x8 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x8 26. "FLEXSPI2_STOP_REQ,FLEXSPI2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 25. "FLEXSPI2_IPG_DOZE,FLEXSPI2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 24. "FLEXSPI1_STOP_REQ,FLEXSPI1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 23. "FLEXSPI1_IPG_DOZE,FLEXSPI1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 22. "FLEXIO2_IPG_DOZE,FLEXIO2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 21. "FLEXIO1_IPG_DOZE,FLEXIO2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 20. "ENET1G_STOP_REQ,ENET1G stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 19. "ENET1G_IPG_DOZE,ENET1G doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 18. "ENET_STOP_REQ,ENET stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 17. "ENET_IPG_DOZE,ENET doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 16. "EDMA_LPSR_STOP_REQ,EDMA_LPSR stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 15. "EDMA_STOP_REQ,EDMA stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 13. "CAN3_STOP_REQ,CAN3 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 12. "CAN3_IPG_DOZE,CAN3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 11. "CAN2_STOP_REQ,CAN2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 10. "CAN2_IPG_DOZE,CAN2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 9. "CAN1_STOP_REQ,CAN1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 8. "CAN1_IPG_DOZE,CAN1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 7. "CAAM_STOP_REQ,CAAM stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 6. "CAAM_IPG_DOZE,CAN3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 5. "ADC2_IPG_STOP_MODE,ADC2 stop mode selection. This bitfield cannot change when ADC2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x8 4. "ADC2_STOP_REQ,ADC2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 3. "ADC2_IPG_DOZE,ADC2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x8 2. "ADC1_IPG_STOP_MODE,ADC1 stop mode selection. This bitfield cannot change when ADC1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x8 1. "ADC1_STOP_REQ,ADC1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x8 0. "ADC1_IPG_DOZE,ADC1 doze mode" "0: Not in doze mode,1: In doze mode" line.long 0xC "GPR36,GPR36 General Purpose Register" bitfld.long 0xC 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0xC 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0xC 26. "LPSPI1_IPG_STOP_MODE,LPSPI1 stop mode selection. This bitfield cannot change when LPSPI1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 25. "LPSPI1_STOP_REQ,LPSPI1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 24. "LPSPI1_IPG_DOZE,LPSPI1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 23. "LPI2C6_IPG_STOP_MODE,LPI2C6 stop mode selection. This bitfield cannot change when LPI2C6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 22. "LPI2C6_STOP_REQ,LPI2C6 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 21. "LPI2C6_IPG_DOZE,LPI2C6 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 20. "LPI2C5_IPG_STOP_MODE,LPI2C5 stop mode selection. This bitfield cannot change when LPI2C5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 19. "LPI2C5_STOP_REQ,LPI2C5 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 18. "LPI2C5_IPG_DOZE,LPI2C5 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 17. "LPI2C4_IPG_STOP_MODE,LPI2C4 stop mode selection. This bitfield cannot change when LPI2C4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 16. "LPI2C4_STOP_REQ,LPI2C4 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 15. "LPI2C4_IPG_DOZE,LPI2C4 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 14. "LPI2C3_IPG_STOP_MODE,LPI2C3 stop mode selection. This bitfield cannot change when LPI2C3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 13. "LPI2C3_STOP_REQ,LPI2C3 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 12. "LPI2C3_IPG_DOZE,LPI2C3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 11. "LPI2C2_IPG_STOP_MODE,LPI2C2 stop mode selection. This bitfield cannot change when LPI2C2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 10. "LPI2C2_STOP_REQ,LPI2C2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 9. "LPI2C2_IPG_DOZE,LPI2C2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 8. "LPI2C1_IPG_STOP_MODE,LPI2C1 stop mode selection. This bitfield cannot change when LPI2C1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0xC 7. "LPI2C1_STOP_REQ,LPI2C1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0xC 6. "LPI2C1_IPG_DOZE,LPI2C1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 5. "GPT6_IPG_DOZE,GPT6 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 4. "GPT5_IPG_DOZE,GPT5 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 3. "GPT4_IPG_DOZE,GPT4 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 2. "GPT3_IPG_DOZE,GPT3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 1. "GPT2_IPG_DOZE,GPT2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0xC 0. "GPT1_IPG_DOZE,GPT1 doze mode" "0: Not in doze mode,1: In doze mode" line.long 0x10 "GPR37,GPR37 General Purpose Register" bitfld.long 0x10 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x10 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x10 26. "LPUART4_IPG_STOP_MODE,LPUART4 stop mode selection. This bitfield cannot change when LPUART4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 25. "LPUART4_STOP_REQ,LPUART4 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 24. "LPUART4_IPG_DOZE,LPUART4 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 23. "LPUART3_IPG_STOP_MODE,LPUART3 stop mode selection. This bitfield cannot change when LPUART3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 22. "LPUART3_STOP_REQ,LPUART3 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 21. "LPUART3_IPG_DOZE,LPUART3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 20. "LPUART2_IPG_STOP_MODE,LPUART2 stop mode selection. This bitfield cannot change when LPUART2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 19. "LPUART2_STOP_REQ,LPUART2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 18. "LPUART2_IPG_DOZE,LPUART2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 17. "LPUART1_IPG_STOP_MODE,LPUART1 stop mode selection. This bitfield cannot change when LPUART1_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 16. "LPUART1_STOP_REQ,LPUART1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 15. "LPUART1_IPG_DOZE,LPUART1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 14. "LPSPI6_IPG_STOP_MODE,LPSPI6 stop mode selection. This bitfield cannot change when LPSPI6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 13. "LPSPI6_STOP_REQ,LPSPI6 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 12. "LPSPI6_IPG_DOZE,LPSPI6 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 11. "LPSPI5_IPG_STOP_MODE,LPSPI5 stop mode selection. This bitfield cannot change when LPSPI5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 10. "LPSPI5_STOP_REQ,LPSPI5 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 9. "LPSPI5_IPG_DOZE,LPSPI5 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 8. "LPSPI4_IPG_STOP_MODE,LPSPI4 stop mode selection. This bitfield cannot change when LPSPI4_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 7. "LPSPI4_STOP_REQ,LPSPI4 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 6. "LPSPI4_IPG_DOZE,LPSPI4 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 5. "LPSPI3_IPG_STOP_MODE,LPSPI3 stop mode selection. This bitfield cannot change when LPSPI3_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 4. "LPSPI3_STOP_REQ,LPSPI3 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 3. "LPSPI3_IPG_DOZE,LPSPI3 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x10 2. "LPSPI2_IPG_STOP_MODE,LPSPI2 stop mode selection. This bitfield cannot change when LPSPI2_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x10 1. "LPSPI2_STOP_REQ,LPSPI2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x10 0. "LPSPI2_IPG_DOZE,LPSPI2 doze mode" "0: Not in doze mode,1: In doze mode" line.long 0x14 "GPR38,GPR38 General Purpose Register" bitfld.long 0x14 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x14 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x14 26. "MIC_IPG_STOP_MODE,MIC stop mode selection. This bitfield cannot change when MIC_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 25. "MIC_STOP_REQ,MIC stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 24. "MIC_IPG_DOZE,MIC doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 23. "LPUART12_IPG_STOP_MODE,LPUART12 stop mode selection. This bitfield cannot change when LPUART12_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 22. "LPUART12_STOP_REQ,LPUART12 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 21. "LPUART12_IPG_DOZE,LPUART12 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 20. "LPUART11_IPG_STOP_MODE,LPUART11 stop mode selection. This bitfield cannot change when LPUART11_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 19. "LPUART11_STOP_REQ,LPUART11 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 18. "LPUART11_IPG_DOZE,LPUART11 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 17. "LPUART10_IPG_STOP_MODE,LPUART10 stop mode selection. This bitfield cannot change when LPUART10_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 16. "LPUART10_STOP_REQ,LPUART10 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 15. "LPUART10_IPG_DOZE,LPUART10 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 14. "LPUART9_IPG_STOP_MODE,LPUART9 stop mode selection. This bitfield cannot change when LPUART9_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 13. "LPUART9_STOP_REQ,LPUART9 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 12. "LPUART9_IPG_DOZE,LPUART9 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 11. "LPUART8_IPG_STOP_MODE,LPUART8 stop mode selection. This bitfield cannot change when LPUART8_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 10. "LPUART8_STOP_REQ,LPUART8 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 9. "LPUART8_IPG_DOZE,LPUART8 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 8. "LPUART7_IPG_STOP_MODE,LPUART7 stop mode selection. This bitfield cannot change when LPUART7_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 7. "LPUART7_STOP_REQ,LPUART7 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 6. "LPUART7_IPG_DOZE,LPUART7 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 5. "LPUART6_IPG_STOP_MODE,LPUART6 stop mode selection. This bitfield cannot change when LPUART6_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 4. "LPUART6_STOP_REQ,LPUART6 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 3. "LPUART6_IPG_DOZE,LPUART6 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x14 2. "LPUART5_IPG_STOP_MODE,LPUART5 stop mode selection. This bitfield cannot change when LPUART5_STOP_REQ is asserted." "0: This module is functional in Stop Mode,1: This module is not functional in Stop Mode and.." newline bitfld.long 0x14 1. "LPUART5_STOP_REQ,LPUART5 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x14 0. "LPUART5_IPG_DOZE,LPUART5 doze mode" "0: Not in doze mode,1: In doze mode" line.long 0x18 "GPR39,GPR39 General Purpose Register" bitfld.long 0x18 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" newline bitfld.long 0x18 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x18 17. "FLEXIO2_STOP_REQ_PER,FLEXIO2 peripheral clock domain stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 16. "FLEXIO2_STOP_REQ_BUS,FLEXIO2 bus clock domain stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 15. "FLEXIO1_STOP_REQ_PER,FLEXIO1 peripheral clock domain stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 14. "FLEXIO1_STOP_REQ_BUS,FLEXIO1 bus clock domain stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 13. "SAI4_STOP_REQ,SAI4 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 12. "SAI3_STOP_REQ,SAI3 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 11. "SAI2_STOP_REQ,SAI2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 10. "SAI1_STOP_REQ,SAI1 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 9. "WDOG2_IPG_DOZE,WDOG2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x18 8. "WDOG1_IPG_DOZE,WDOG1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x18 7. "SNVS_HP_STOP_REQ,SNVS_HP stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 6. "SNVS_HP_IPG_DOZE,SNVS_HP doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x18 5. "SIM2_IPG_DOZE,SIM2 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x18 4. "SIM1_IPG_DOZE,SIM1 doze mode" "0: Not in doze mode,1: In doze mode" newline bitfld.long 0x18 3. "SEMC_STOP_REQ,SEMC stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 2. "PIT2_STOP_REQ,PIT2 stop request" "0: Stop request off,1: Stop request on" newline bitfld.long 0x18 1. "PIT1_STOP_REQ,PIT1 stop request" "0: Stop request off,1: Stop request on" rgroup.long 0xA0++0x7 line.long 0x0 "GPR40,GPR40 General Purpose Register" bitfld.long 0x0 31. "LPUART8_STOP_ACK,LPUART8 stop acknowledge" "0,1" newline bitfld.long 0x0 30. "LPUART7_STOP_ACK,LPUART7 stop acknowledge" "0,1" newline bitfld.long 0x0 29. "LPUART6_STOP_ACK,LPUART6 stop acknowledge" "0,1" newline bitfld.long 0x0 28. "LPUART5_STOP_ACK,LPUART5 stop acknowledge" "0,1" newline bitfld.long 0x0 27. "LPUART4_STOP_ACK,LPUART4 stop acknowledge" "0,1" newline bitfld.long 0x0 26. "LPUART3_STOP_ACK,LPUART3 stop acknowledge" "0,1" newline bitfld.long 0x0 25. "LPUART2_STOP_ACK,LPUART2 stop acknowledge" "0,1" newline bitfld.long 0x0 24. "LPUART1_STOP_ACK,LPUART1 stop acknowledge" "0,1" newline bitfld.long 0x0 23. "LPSPI6_STOP_ACK,LPSPI6 stop acknowledge" "0,1" newline bitfld.long 0x0 22. "LPSPI5_STOP_ACK,LPSPI5 stop acknowledge" "0,1" newline bitfld.long 0x0 21. "LPSPI4_STOP_ACK,LPSPI4 stop acknowledge" "0,1" newline bitfld.long 0x0 20. "LPSPI3_STOP_ACK,LPSPI3 stop acknowledge" "0,1" newline bitfld.long 0x0 19. "LPSPI2_STOP_ACK,LPSPI2 stop acknowledge" "0,1" newline bitfld.long 0x0 18. "LPSPI1_STOP_ACK,LPSPI1 stop acknowledge" "0,1" newline bitfld.long 0x0 17. "LPI2C6_STOP_ACK,LPI2C6 stop acknowledge" "0,1" newline bitfld.long 0x0 16. "LPI2C5_STOP_ACK,LPI2C5 stop acknowledge" "0,1" newline bitfld.long 0x0 15. "LPI2C4_STOP_ACK,LPI2C4 stop acknowledge" "0,1" newline bitfld.long 0x0 14. "LPI2C3_STOP_ACK,LPI2C3 stop acknowledge" "0,1" newline bitfld.long 0x0 13. "LPI2C2_STOP_ACK,LPI2C2 stop acknowledge" "0,1" newline bitfld.long 0x0 12. "LPI2C1_STOP_ACK,LPI2C1 stop acknowledge" "0,1" newline bitfld.long 0x0 11. "FLEXSPI2_STOP_ACK,FLEXSPI2 stop acknowledge" "0,1" newline bitfld.long 0x0 10. "FLEXSPI1_STOP_ACK,FLEXSPI1 stop acknowledge" "0,1" newline bitfld.long 0x0 9. "ENET1G_STOP_ACK,ENET1G stop acknowledge" "0,1" newline bitfld.long 0x0 8. "ENET_STOP_ACK,ENET stop acknowledge" "0,1" newline bitfld.long 0x0 7. "EDMA_LPSR_STOP_ACK,EDMA_LPSR stop acknowledge" "0,1" newline bitfld.long 0x0 6. "EDMA_STOP_ACK,EDMA stop acknowledge" "0,1" newline bitfld.long 0x0 5. "CAN3_STOP_ACK,CAN3 stop acknowledge" "0,1" newline bitfld.long 0x0 4. "CAN2_STOP_ACK,CAN2 stop acknowledge" "0,1" newline bitfld.long 0x0 3. "CAN1_STOP_ACK,CAN1 stop acknowledge" "0,1" newline bitfld.long 0x0 2. "CAAM_STOP_ACK,CAAM stop acknowledge" "0,1" newline bitfld.long 0x0 1. "ADC2_STOP_ACK,ADC2 stop acknowledge" "0,1" newline bitfld.long 0x0 0. "ADC1_STOP_ACK,ADC1 stop acknowledge" "0,1" line.long 0x4 "GPR41,GPR41 General Purpose Register" bitfld.long 0x4 24. "ROM_READ_LOCKED,ROM read lock status bit" "0,1" newline bitfld.long 0x4 16. "FLEXIO2_STOP_ACK_PER,FLEXIO2 stop acknowledge of peripheral clock domain" "0,1" newline bitfld.long 0x4 15. "FLEXIO2_STOP_ACK_BUS,FLEXIO2 stop acknowledge of bus clock domain" "0,1" newline bitfld.long 0x4 14. "FLEXIO1_STOP_ACK_PER,FLEXIO1 stop acknowledge of peripheral clock domain" "0,1" newline bitfld.long 0x4 13. "FLEXIO1_STOP_ACK_BUS,FLEXIO1 stop acknowledge of bus clock domain" "0,1" newline bitfld.long 0x4 12. "SAI4_STOP_ACK,SAI4 stop acknowledge" "0,1" newline bitfld.long 0x4 11. "SAI3_STOP_ACK,SAI3 stop acknowledge" "0,1" newline bitfld.long 0x4 10. "SAI2_STOP_ACK,SAI2 stop acknowledge" "0,1" newline bitfld.long 0x4 9. "SAI1_STOP_ACK,SAI1 stop acknowledge" "0,1" newline bitfld.long 0x4 8. "SNVS_HP_STOP_ACK,SNVS_HP stop acknowledge" "0,1" newline bitfld.long 0x4 7. "SEMC_STOP_ACK,SEMC stop acknowledge" "0,1" newline bitfld.long 0x4 6. "PIT2_STOP_ACK,PIT2 stop acknowledge" "0,1" newline bitfld.long 0x4 5. "PIT1_STOP_ACK,PIT1 stop acknowledge" "0,1" newline bitfld.long 0x4 4. "MIC_STOP_ACK,MIC stop acknowledge" "0,1" newline bitfld.long 0x4 3. "LPUART12_STOP_ACK,LPUART12 stop acknowledge" "0,1" newline bitfld.long 0x4 2. "LPUART11_STOP_ACK,LPUART11 stop acknowledge" "0,1" newline bitfld.long 0x4 1. "LPUART10_STOP_ACK,LPUART10 stop acknowledge" "0,1" newline bitfld.long 0x4 0. "LPUART9_STOP_ACK,LPUART9 stop acknowledge" "0,1" tree.end tree "IOMUXC_SNVS" base ad:0x40C94000 group.long 0x0++0x73 line.long 0x0 "SW_MUX_CTL_PAD_WAKEUP_DIG,SW_MUX_CTL_PAD_WAKEUP_DIG SW MUX Control Register" bitfld.long 0x0 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad WAKEUP_DIG" bitfld.long 0x0 0.--2. "MUX_MODE,MUX Mode Select Field." "?,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO00 of..,?,7: Select mux mode: ALT7 mux port: NMI_GLUE_NMI of.." line.long 0x4 "SW_MUX_CTL_PAD_PMIC_ON_REQ_DIG,SW_MUX_CTL_PAD_PMIC_ON_REQ_DIG SW MUX Control Register" bitfld.long 0x4 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad PMIC_ON_REQ_DIG" bitfld.long 0x4 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port:..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO01 of..,?,?" line.long 0x8 "SW_MUX_CTL_PAD_PMIC_STBY_REQ_DIG,SW_MUX_CTL_PAD_PMIC_STBY_REQ_DIG SW MUX Control Register" bitfld.long 0x8 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad PMIC_STBY_REQ_DIG" bitfld.long 0x8 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port:..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO02 of..,?,?" line.long 0xC "SW_MUX_CTL_PAD_GPIO_SNVS_00_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_00_DIG SW MUX Control Register" bitfld.long 0xC 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_00_DIG" bitfld.long 0xC 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER0 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO03 of..,?,?" line.long 0x10 "SW_MUX_CTL_PAD_GPIO_SNVS_01_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_01_DIG SW MUX Control Register" bitfld.long 0x10 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_01_DIG" bitfld.long 0x10 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER1 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO04 of..,?,?" line.long 0x14 "SW_MUX_CTL_PAD_GPIO_SNVS_02_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_02_DIG SW MUX Control Register" bitfld.long 0x14 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_02_DIG" bitfld.long 0x14 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER2 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO05 of..,?,?" line.long 0x18 "SW_MUX_CTL_PAD_GPIO_SNVS_03_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_03_DIG SW MUX Control Register" bitfld.long 0x18 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_03_DIG" bitfld.long 0x18 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER3 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO06 of..,?,?" line.long 0x1C "SW_MUX_CTL_PAD_GPIO_SNVS_04_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_04_DIG SW MUX Control Register" bitfld.long 0x1C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_04_DIG" bitfld.long 0x1C 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER4 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO07 of..,?,?" line.long 0x20 "SW_MUX_CTL_PAD_GPIO_SNVS_05_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_05_DIG SW MUX Control Register" bitfld.long 0x20 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_05_DIG" bitfld.long 0x20 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER5 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO08 of..,?,?" line.long 0x24 "SW_MUX_CTL_PAD_GPIO_SNVS_06_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_06_DIG SW MUX Control Register" bitfld.long 0x24 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_06_DIG" bitfld.long 0x24 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER6 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO09 of..,?,?" line.long 0x28 "SW_MUX_CTL_PAD_GPIO_SNVS_07_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_07_DIG SW MUX Control Register" bitfld.long 0x28 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_07_DIG" bitfld.long 0x28 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER7 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO10 of..,?,?" line.long 0x2C "SW_MUX_CTL_PAD_GPIO_SNVS_08_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_08_DIG SW MUX Control Register" bitfld.long 0x2C 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_08_DIG" bitfld.long 0x2C 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER8 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO11 of..,?,?" line.long 0x30 "SW_MUX_CTL_PAD_GPIO_SNVS_09_DIG,SW_MUX_CTL_PAD_GPIO_SNVS_09_DIG SW MUX Control Register" bitfld.long 0x30 4. "SION,Software Input On Field." "0: Input Path is determined by functionality,1: Force input path of pad GPIO_SNVS_09_DIG" bitfld.long 0x30 0.--2. "MUX_MODE,MUX Mode Select Field." "0: Select mux mode: ALT0 mux port: SNVS_TAMPER9 of..,?,?,?,?,5: Select mux mode: ALT5 mux port: GPIO13_IO12 of..,?,?" line.long 0x34 "SW_PAD_CTL_PAD_TEST_MODE_DIG,SW_PAD_CTL_PAD_TEST_MODE_DIG SW PAD Control Register" bitfld.long 0x34 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x34 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x34 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" bitfld.long 0x34 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" newline bitfld.long 0x34 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" bitfld.long 0x34 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x38 "SW_PAD_CTL_PAD_POR_B_DIG,SW_PAD_CTL_PAD_POR_B_DIG SW PAD Control Register" bitfld.long 0x38 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x38 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x38 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" bitfld.long 0x38 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" newline bitfld.long 0x38 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" bitfld.long 0x38 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x3C "SW_PAD_CTL_PAD_ONOFF_DIG,SW_PAD_CTL_PAD_ONOFF_DIG SW PAD Control Register" bitfld.long 0x3C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x3C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x3C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" bitfld.long 0x3C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" newline bitfld.long 0x3C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" bitfld.long 0x3C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x40 "SW_PAD_CTL_PAD_WAKEUP_DIG,SW_PAD_CTL_PAD_WAKEUP_DIG SW PAD Control Register" bitfld.long 0x40 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x40 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x40 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x40 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x40 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x40 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x40 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x44 "SW_PAD_CTL_PAD_PMIC_ON_REQ_DIG,SW_PAD_CTL_PAD_PMIC_ON_REQ_DIG SW PAD Control Register" bitfld.long 0x44 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x44 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x44 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x44 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x44 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x44 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x44 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x48 "SW_PAD_CTL_PAD_PMIC_STBY_REQ_DIG,SW_PAD_CTL_PAD_PMIC_STBY_REQ_DIG SW PAD Control Register" bitfld.long 0x48 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x48 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x48 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x48 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x48 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x48 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x48 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x4C "SW_PAD_CTL_PAD_GPIO_SNVS_00_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_00_DIG SW PAD Control Register" bitfld.long 0x4C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x4C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x4C 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x4C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x4C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x4C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x4C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x50 "SW_PAD_CTL_PAD_GPIO_SNVS_01_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_01_DIG SW PAD Control Register" bitfld.long 0x50 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x50 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x50 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x50 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x50 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x50 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x50 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x54 "SW_PAD_CTL_PAD_GPIO_SNVS_02_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_02_DIG SW PAD Control Register" bitfld.long 0x54 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x54 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x54 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x54 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x54 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x54 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x54 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x58 "SW_PAD_CTL_PAD_GPIO_SNVS_03_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_03_DIG SW PAD Control Register" bitfld.long 0x58 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x58 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x58 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x58 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x58 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x58 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x58 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x5C "SW_PAD_CTL_PAD_GPIO_SNVS_04_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_04_DIG SW PAD Control Register" bitfld.long 0x5C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x5C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x5C 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x5C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x5C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x5C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x5C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x60 "SW_PAD_CTL_PAD_GPIO_SNVS_05_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_05_DIG SW PAD Control Register" bitfld.long 0x60 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x60 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x60 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x60 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x60 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x60 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x60 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x64 "SW_PAD_CTL_PAD_GPIO_SNVS_06_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_06_DIG SW PAD Control Register" bitfld.long 0x64 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x64 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x64 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x64 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x64 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x64 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x64 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x68 "SW_PAD_CTL_PAD_GPIO_SNVS_07_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_07_DIG SW PAD Control Register" bitfld.long 0x68 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x68 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x68 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x68 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x68 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x68 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x68 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x6C "SW_PAD_CTL_PAD_GPIO_SNVS_08_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_08_DIG SW PAD Control Register" bitfld.long 0x6C 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x6C 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x6C 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x6C 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x6C 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x6C 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x6C 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" line.long 0x70 "SW_PAD_CTL_PAD_GPIO_SNVS_09_DIG,SW_PAD_CTL_PAD_GPIO_SNVS_09_DIG SW PAD Control Register" bitfld.long 0x70 30.--31. "DWP_LOCK,Domain write protection lock" "0: Neither of DWP bits is locked,1: The lower DWP bit is locked,2: The higher DWP bit is locked,3: Both DWP bits are locked" bitfld.long 0x70 28.--29. "DWP,Domain write protection" "0: Both cores are allowed,1: CM7 is forbidden,2: CM4 is forbidden,3: Both cores are forbidden" newline bitfld.long 0x70 6. "ODE_SNVS,Open Drain SNVS Field" "0: Disabled,1: Enabled" bitfld.long 0x70 3. "PUS,Pull Up / Down Config. Field" "0: Weak pull down,1: Weak pull up" newline bitfld.long 0x70 2. "PUE,Pull / Keep Select Field" "0: Pull Disable,1: Pull Enable" bitfld.long 0x70 1. "DSE,Drive Strength Field" "0: normal driver,1: high driver" newline bitfld.long 0x70 0. "SRE,Slew Rate Field" "0: Slow Slew Rate,1: Fast Slew Rate" tree.end tree "IOMUXC_SNVS_GPR" base ad:0x40C98000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "GPR[$1],GPR0 General Purpose Register" hexmask.long 0x0 0.--31. 1. "GPR,General purpose bits" repeat.end group.long 0x80++0x17 line.long 0x0 "GPR32,GPR32 General Purpose Register" hexmask.long.word 0x0 16.--31. 1. "LOCK,Lock the write to bit 15:0" newline hexmask.long.word 0x0 1.--15. 1. "GPR,General purpose bits" line.long 0x4 "GPR33,GPR33 General Purpose Register" rbitfld.long 0x4 20. "SNVS_XTAL_CLK_OK,32K OSC ok flag" "0: 32K oscillator is NOT stable into normal operation,1: 32K oscillator is stable into normal operation" newline rbitfld.long 0x4 19. "DCDC_STS_DC_OK,DCDC status OK" "0: DCDC is settling,1: DCDC already settled" newline rbitfld.long 0x4 18. "DCDC_OVER_VOL,DCDC output over voltage alert" "0: No Overvoltage on DCDC VDDLP0 or VDDLP8 output,1: Overvoltage on DCDC VDDLP0 or VDDLP8 output" newline rbitfld.long 0x4 17. "DCDC_OVER_CUR,DCDC output over current alert" "0: No Overcurrent on DCDC output,1: Overcurrent on DCDC output" newline rbitfld.long 0x4 16. "DCDC_IN_LOW_VOL,DCDC_IN low voltage detect" "0: Voltage on DCDC_IN is higher than 2.6V,1: Voltage on DCDC_IN is lower than 2.6V" newline bitfld.long 0x4 2. "SNVS_BYPASS_EN,SNVS LDO_SNVS_ANA bypass enable" "0: Disable bypass,1: Enable bypass" newline bitfld.long 0x4 1. "DCDC_STATUS_CAPT_CLR,DCDC captured status clear" "0: No change,1: Clear the 3 bits of DCDC captured status:.." line.long 0x8 "GPR34,GPR34 General Purpose Register" hexmask.long.byte 0x8 24.--27. 1. "SNVS_OSC_CAP_TRIM,SNVS OSC load capacitor trim" newline bitfld.long 0x8 23. "SNVS_CAP_TRIM_SEL,SNVS OSC load capacitor trim select" "0: The trimming codes are selected from eFuse,1: The trimming codes are used from.." newline bitfld.long 0x8 18.--19. "SNVS_CLK_DET_OFFSET_LOW,SNVS clock detect offset of low boundary frequency" "0: No change (Default),1: Add +5 to the Trim,2: Add +10 to the trim,3: Add -5 to the Trim" newline bitfld.long 0x8 16.--17. "SNVS_CLK_DET_OFFSET_HIGH,SNVS clock detect offset of high boundary frequency" "0: No change (Default),1: Add +5 to the Trim,2: Add +10 to the trim,3: Add -5 to the Trim" newline hexmask.long.byte 0x8 8.--15. 1. "SNVS_CLK_DET_TRIM,SNVS clock detect trim bits" newline bitfld.long 0x8 7. "SNVS_CLK_DET_TRIM_SEL,SNVS clock detect trim select" "0: The trimming codes are selected from eFuse,1: The trimming codes of clock detector used to.." newline bitfld.long 0x8 2.--3. "SNVS_CORE_VOLT_DET_TRIM,SNVS core voltage detect trim" "0,1,2,3" newline bitfld.long 0x8 1. "SNVS_CORE_VOLT_DET_TRIM_SEL,SNVS core voltage detect trim select" "0: The trimming codes are selected from eFuse,1: The trimming codes of core voltage detectors.." newline bitfld.long 0x8 0. "LOCK,Lock the write to bit 31:1" "0: Write access is not blocked,1: Write access is blocked" line.long 0xC "GPR35,GPR35 General Purpose Register" bitfld.long 0xC 30.--31. "SNVS_TEMP_DET_OFFSET_LOW,SNVS temperature detect offset of low temperature boundary" "0: No change (Default),1: Add +5 to the Trim,2: Add +10 to the trim,3: Add -5 to the Trim" newline bitfld.long 0xC 28.--29. "SNVS_TEMP_DET_OFFSET_HIGH,SNVS temperature detect offset of high temperature boundary" "0: No change (Default),1: Add +5 to the Trim,2: Add +10 to the trim,3: Add -5 to the Trim" newline hexmask.long.word 0xC 16.--27. 1. "SNVS_TEMP_DET_TRIM,SNVS temperature detect trim" newline bitfld.long 0xC 15. "SNVS_TEMP_DET_TRIM_SEL,SNVS temperature detect trim select" "0: The trimming codes are selected from eFuse,1: The trimming codes to define the temperature.." newline hexmask.long.byte 0xC 4.--11. 1. "SNVS_VOLT_DET_TRIM,SNVS voltage detect trim" newline bitfld.long 0xC 3. "SNVS_VOLT_DET_TRIM_SEL,SNVS voltage detect trim select" "0: The trimming codes are selected from eFuse,1: The trimming codes of voltage detectors to.." newline bitfld.long 0xC 0. "LOCK,Lock the write to bit 31:1" "0: Write access is not blocked,1: Write access is blocked" line.long 0x10 "GPR36,GPR36 General Purpose Register" bitfld.long 0x10 31. "SNVS_SRAM_PSWSMALL,SNVS SRAM small switch control bit" "0: Switch on SNVS SRAM power for peripheral and array,1: Switch off SNVS SRAM power for peripheral and.." newline bitfld.long 0x10 30. "SNVS_SRAM_PSWSMALLMP_FORCE,SNVS SRAM small switch control bit for peripheral" "0: Switch on SNVS SRAM power for peripheral,1: Switch off SNVS SRAM power for peripheral (SRAM.." newline bitfld.long 0x10 29. "SNVS_SRAM_PSWLARGE,SNVS SRAM large switch control bit" "0: Switch on SNVS SRAM power for peripheral and array,1: Switch off SNVS SRAM power for peripheral and.." newline bitfld.long 0x10 28. "SNVS_SRAM_PSWLARGEMP_FORCE,SNVS SRAM large switch control bit for peripheral" "0: Switch on SNVS SRAM power for peripheral,1: Switch off SNVS SRAM power for peripheral (SRAM.." newline bitfld.long 0x10 27. "SNVS_SRAM_STDBY,SNVS SRAM standby enable bit" "0: SNVS SRAM does not enter low leakage state,1: SNVS SRAM enters low leakage state and large.." newline bitfld.long 0x10 26. "SNVS_SRAM_SLEEP,SNVS SRAM power-down enable bit" "0: Enable SRAM access (It should be cleared after..,1: SNVS SRAM can go in Shutdown/ Periphery Off.." newline bitfld.long 0x10 23. "SNVSDIG_SNVS1P8_ISO_EN,SNVS RAM isolation enable bit" "0: Enable SRAM access (It should be cleared after..,1: Enable the isolation to avoid extra leakage.." line.long 0x14 "GPR37,GPR37 General Purpose Register" hexmask.long.word 0x14 11.--20. 1. "SNVS_TAMPER_PUS,SNVS tamper detect pin pull selection bit" newline hexmask.long.word 0x14 1.--10. 1. "SNVS_TAMPER_PUE,SNVS tamper detect pin pull enable bit" newline bitfld.long 0x14 0. "LOCK,Lock the write to bit 31:1" "0: Write access is not blocked,1: Write access is blocked" tree.end tree.end tree "IPS_DOMAIN" base ad:0x40C87C00 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40C87C00 ad:0x40C87C10 ad:0x40C87C20 ad:0x40C87C30 ad:0x40C87C40 ad:0x40C87C50 ad:0x40C87C60 ad:0x40C87C70 ad:0x40C87C80 ad:0x40C87C90 ad:0x40C87CA0 ad:0x40C87CB0 ad:0x40C87CC0 ad:0x40C87CD0 ad:0x40C87CE0 ad:0x40C87CF0) tree "SLOT_CTRL[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "SLOT_CTRL,Slot Control Register" bitfld.long 0x0 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x0 17. "ALLOW_USER,Allow user write access to this domain control register or domain register" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x0 16. "ALLOW_NONSECURE,Allow non-secure write access to this domain control register or domain register" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x0 15. "DOMAIN_LOCK,Lock domain ID of this slot" "0: Do not lock the domain ID,1: Lock the domain ID" newline hexmask.long.byte 0x0 0.--3. 1. "LOCKED_DOMAIN_ID,Domain ID of the slot to be locked" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40C87D00 ad:0x40C87D10 ad:0x40C87D20 ad:0x40C87D30 ad:0x40C87D40 ad:0x40C87D50 ad:0x40C87D60 ad:0x40C87D70 ad:0x40C87D80 ad:0x40C87D90 ad:0x40C87DA0 ad:0x40C87DB0 ad:0x40C87DC0 ad:0x40C87DD0 ad:0x40C87DE0 ad:0x40C87DF0) tree "SLOT_CTRL[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "SLOT_CTRL,Slot Control Register" bitfld.long 0x0 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x0 17. "ALLOW_USER,Allow user write access to this domain control register or domain register" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x0 16. "ALLOW_NONSECURE,Allow non-secure write access to this domain control register or domain register" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x0 15. "DOMAIN_LOCK,Lock domain ID of this slot" "0: Do not lock the domain ID,1: Lock the domain ID" newline hexmask.long.byte 0x0 0.--3. 1. "LOCKED_DOMAIN_ID,Domain ID of the slot to be locked" tree.end repeat.end repeat 6. (list 0x20 0x21 0x22 0x23 0x24 0x25)(list ad:0x40C87E00 ad:0x40C87E10 ad:0x40C87E20 ad:0x40C87E30 ad:0x40C87E40 ad:0x40C87E50) tree "SLOT_CTRL[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "SLOT_CTRL,Slot Control Register" bitfld.long 0x0 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x0 17. "ALLOW_USER,Allow user write access to this domain control register or domain register" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x0 16. "ALLOW_NONSECURE,Allow non-secure write access to this domain control register or domain register" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x0 15. "DOMAIN_LOCK,Lock domain ID of this slot" "0: Do not lock the domain ID,1: Lock the domain ID" newline hexmask.long.byte 0x0 0.--3. 1. "LOCKED_DOMAIN_ID,Domain ID of the slot to be locked" tree.end repeat.end tree.end tree "KEY_MANAGER" base ad:0x40C80000 group.long 0x0++0x3 line.long 0x0 "MASTER_KEY_CTRL,CSR Master Key Control Register" bitfld.long 0x0 16. "LOCK,lock this register prevent from writing. Default value comes from FUSE_MASTER_KEY_SEL_LOCK." "0: not locked,1: locked" bitfld.long 0x0 0. "SELECT,Key select for SNVS OTPMK. Default value comes from FUSE_MASTER_KEY_SEL." "0: select key from UDF,1: If LOCK = 1 select key from PUF otherwise select.." group.long 0x10++0x3 line.long 0x0 "OTFAD1_KEY_CTRL,CSR OTFAD-1 Key Control" bitfld.long 0x0 16. "LOCK,lock this register prevent from writing. Default value comes from FUSE_OTFAD1_KEY_SEL_LOCK." "0: not locked,1: locked" bitfld.long 0x0 0. "SELECT,key select for OTFAD-1. Default value comes from FUSE_OTFAD1_KEY_SEL." "0: Select key from OCOTP USER_KEY5,1: If PUF_KEY_CTRL[LOCK] is 1 select key from PUF.." group.long 0x18++0x3 line.long 0x0 "OTFAD2_KEY_CTRL,CSR OTFAD-2 Key Control" bitfld.long 0x0 16. "LOCK,lock this register prevent from writing. Default value comes from FUSE_OTFAD2_KEY_SEL_LOCK." "0: not locked,1: locked" bitfld.long 0x0 0. "SELECT,key select for OTFAD-2. Default value comes from FUSE_OTFAD1_KEY_SEL." "0: select key from OCOTP USER_KEY5,1: If PUF_KEY_CTRL[LOCK] is 1 select key from PUF.." group.long 0x20++0x3 line.long 0x0 "IEE_KEY_CTRL,CSR IEE Key Control" bitfld.long 0x0 0. "RELOAD,Restart load key signal for IEE" "0: Do nothing,1: Restart IEE key load flow" group.long 0x30++0x3 line.long 0x0 "PUF_KEY_CTRL,CSR PUF Key Control" bitfld.long 0x0 0. "LOCK,Lock signal for key select" "0: Do not lock the key select,1: Lock the key select to select key from PUF.." group.long 0x400++0x13 line.long 0x0 "SLOT0_CTRL,Slot 0 Control" bitfld.long 0x0 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x0 17. "TZ_USER,Allow user write access to this register and the slot it controls" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x0 16. "TZ_NS,Allow non-secure write access to this register and the slot it controls" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x0 15. "LOCK_LIST,Lock whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x0 0.--3. 1. "WHITE_LIST,Whitelist" line.long 0x4 "SLOT1_CTRL,Slot1 Control" bitfld.long 0x4 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x4 17. "TZ_USER,Allow user write access to this register and the slot it controls" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x4 16. "TZ_NS,Allow non-secure write access to this register and the slot it controls" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x4 15. "LOCK_LIST,Lock whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x4 0.--3. 1. "WHITE_LIST,Whitelist" line.long 0x8 "SLOT2_CTRL,Slot2 Control" bitfld.long 0x8 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x8 17. "TZ_USER,Allow user write access to this register and the slot it controls" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x8 16. "TZ_NS,Allow non-secure write access to this register and the slot it controls" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x8 15. "LOCK_LIST,Lock whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x8 0.--3. 1. "WHITE_LIST,Whitelist" line.long 0xC "SLOT3_CTRL,Slot3 Control" bitfld.long 0xC 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0xC 17. "TZ_USER,Allow user write access to this register and the slot it controls" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0xC 16. "TZ_NS,Allow non-secure write access to this register and the slot it controls" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0xC 15. "LOCK_LIST,Lock whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0xC 0.--3. 1. "WHITE_LIST,Whitelist" line.long 0x10 "SLOT4_CTRL,Slot 4 Control" bitfld.long 0x10 31. "LOCK_CONTROL,Lock control of this slot" "0: Do not lock the control register of this slot,1: Lock the control register of this slot" bitfld.long 0x10 17. "TZ_USER,Allow user write access to this register and the slot it controls" "0: Do not allow user write access,1: Allow user write access" newline bitfld.long 0x10 16. "TZ_NS,Allow non-secure write access to this register and the slot it controls" "0: Do not allow non-secure write access,1: Allow non-secure write access" bitfld.long 0x10 15. "LOCK_LIST,Lock whitelist" "0: Whitelist is not locked,1: Whitelist is locked" newline hexmask.long.byte 0x10 0.--3. 1. "WHITE_LIST,Whitelist" tree.end tree "KPP" base ad:0x400E0000 group.word 0x0++0x7 line.word 0x0 "KPCR,Keypad Control Register" hexmask.word.byte 0x0 8.--15. 1. "KCO,KCO" hexmask.word.byte 0x0 0.--7. 1. "KRE,KRE" line.word 0x2 "KPSR,Keypad Status Register" bitfld.word 0x2 9. "KRIE,KRIE" "0: No interrupt request is generated when KPKR is..,1: An interrupt request is generated when KPKR is.." bitfld.word 0x2 8. "KDIE,KDIE" "0: No interrupt request is generated when KPKD is..,1: An interrupt request is generated when KPKD is.." newline bitfld.word 0x2 3. "KRSS,KRSS" "0: No effect,1: Set bits which sets keypad release synchronizer.." bitfld.word 0x2 2. "KDSC,KDSC" "0: No effect,1: Set bits that clear the keypad depress.." newline eventfld.word 0x2 1. "KPKR,KPKR" "0: No key release detected,1: All keys have been released" eventfld.word 0x2 0. "KPKD,KPKD" "0: No key presses detected,1: A key has been depressed" line.word 0x4 "KDDR,Keypad Data Direction Register" hexmask.word.byte 0x4 8.--15. 1. "KCDD,KCDD" hexmask.word.byte 0x4 0.--7. 1. "KRDD,KRDD" line.word 0x6 "KPDR,Keypad Data Register" hexmask.word.byte 0x6 8.--15. 1. "KCD,KCD" hexmask.word.byte 0x6 0.--7. 1. "KRD,KRD" tree.end sif (cpuis("IMXRT1166-CM4")||cpuis("IMXRT1166-CM7")) tree "LCDIF" base ad:0x40804000 group.long 0x0++0x33 line.long 0x0 "CTRL,LCDIF General Control Register" bitfld.long 0x0 31. "SFTRST,This bit must be set to zero to enable normal operation of the LCDIF" "0,1" newline bitfld.long 0x0 30. "CLKGATE,This bit must be set to zero for normal operation" "0,1" newline bitfld.long 0x0 26. "DATA_SHIFT_DIR,Use this bit to determine the direction of shift of transmit data." "0: Data to be transmitted is shifted LEFT by..,1: Data to be transmitted is shifted RIGHT by.." newline hexmask.long.byte 0x0 21.--25. 1. "SHIFT_NUM_BITS,The data to be transmitted is shifted left or right by this number of bits." newline bitfld.long 0x0 19. "BYPASS_COUNT,When this bit is 0 it means that LCDIF will stop the block operation and turn off the RUN bit after the amount of data indicated by the LCDIF_TRANSFER_COUNT register has been transferred out" "0,1" newline bitfld.long 0x0 17. "DOTCLK_MODE,Set this bit to 1 to make the hardware go into the DOTCLK mode i" "0,1" newline bitfld.long 0x0 14.--15. "INPUT_DATA_SWIZZLE,This field specifies how to swap the bytes fetched by the bus master interface" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x0 12.--13. "CSC_DATA_SWIZZLE,This field specifies how to swap the bytes after the data has been converted into an internal representation of 24 bits per pixel and before it is transmitted over the LCD interface bus" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x0 10.--11. "LCD_DATABUS_WIDTH,LCD Data bus transfer width. When LUT enabled this field should be set to 0x01." "0: 16-bit data bus mode.,1: 8-bit data bus mode.,2: 18-bit data bus mode.,3: 24-bit data bus mode." newline bitfld.long 0x0 8.--9. "WORD_LENGTH,Input data format." "0: Input data is 16 bits per pixel.,1: Input data is 8 bits wide.,2: Input data is 18 bits per pixel.,3: Input data is 24 bits per pixel." newline bitfld.long 0x0 6. "ENABLE_PXP_HANDSHAKE,If this bit is set and LCDIF_MASTER bit is set the LCDIF will act as bus master and the handshake mechanism between LCDIF and PXP will be turned on" "0,1" newline bitfld.long 0x0 5. "MASTER,Set this bit to make the LCDIF act as a bus master" "0,1" newline bitfld.long 0x0 3. "DATA_FORMAT_16_BIT,When this bit is 1 and WORD_LENGTH = 0 it implies that the 16-bit data is in ARGB555 format" "0,1" newline bitfld.long 0x0 2. "DATA_FORMAT_18_BIT,Used only when WORD_LENGTH = 2 i.e. 18-bit." "0: Data input to the block is in 18 bpp format such..,1: Data input to the block is in 18 bpp format such.." newline bitfld.long 0x0 1. "DATA_FORMAT_24_BIT,Used only when WORD_LENGTH = 3 i" "0: Data input to the block is in 24 bpp format such..,1: Data input to the block is actually RGB 18 bpp.." newline bitfld.long 0x0 0. "RUN,When this bit is set by software the LCDIF will begin transferring data between the SoC and the display" "0,1" line.long 0x4 "CTRL_SET,LCDIF General Control Register" bitfld.long 0x4 31. "SFTRST,This bit must be set to zero to enable normal operation of the LCDIF" "0,1" newline bitfld.long 0x4 30. "CLKGATE,This bit must be set to zero for normal operation" "0,1" newline bitfld.long 0x4 26. "DATA_SHIFT_DIR,Use this bit to determine the direction of shift of transmit data." "0: Data to be transmitted is shifted LEFT by..,1: Data to be transmitted is shifted RIGHT by.." newline hexmask.long.byte 0x4 21.--25. 1. "SHIFT_NUM_BITS,The data to be transmitted is shifted left or right by this number of bits." newline bitfld.long 0x4 19. "BYPASS_COUNT,When this bit is 0 it means that LCDIF will stop the block operation and turn off the RUN bit after the amount of data indicated by the LCDIF_TRANSFER_COUNT register has been transferred out" "0,1" newline bitfld.long 0x4 17. "DOTCLK_MODE,Set this bit to 1 to make the hardware go into the DOTCLK mode i" "0,1" newline bitfld.long 0x4 14.--15. "INPUT_DATA_SWIZZLE,This field specifies how to swap the bytes fetched by the bus master interface" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x4 12.--13. "CSC_DATA_SWIZZLE,This field specifies how to swap the bytes after the data has been converted into an internal representation of 24 bits per pixel and before it is transmitted over the LCD interface bus" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x4 10.--11. "LCD_DATABUS_WIDTH,LCD Data bus transfer width. When LUT enabled this field should be set to 0x01." "0: 16-bit data bus mode.,1: 8-bit data bus mode.,2: 18-bit data bus mode.,3: 24-bit data bus mode." newline bitfld.long 0x4 8.--9. "WORD_LENGTH,Input data format." "0: Input data is 16 bits per pixel.,1: Input data is 8 bits wide.,2: Input data is 18 bits per pixel.,3: Input data is 24 bits per pixel." newline bitfld.long 0x4 6. "ENABLE_PXP_HANDSHAKE,If this bit is set and LCDIF_MASTER bit is set the LCDIF will act as bus master and the handshake mechanism between LCDIF and PXP will be turned on" "0,1" newline bitfld.long 0x4 5. "MASTER,Set this bit to make the LCDIF act as a bus master" "0,1" newline bitfld.long 0x4 3. "DATA_FORMAT_16_BIT,When this bit is 1 and WORD_LENGTH = 0 it implies that the 16-bit data is in ARGB555 format" "0,1" newline bitfld.long 0x4 2. "DATA_FORMAT_18_BIT,Used only when WORD_LENGTH = 2 i.e. 18-bit." "0: Data input to the block is in 18 bpp format such..,1: Data input to the block is in 18 bpp format such.." newline bitfld.long 0x4 1. "DATA_FORMAT_24_BIT,Used only when WORD_LENGTH = 3 i" "0: Data input to the block is in 24 bpp format such..,1: Data input to the block is actually RGB 18 bpp.." newline bitfld.long 0x4 0. "RUN,When this bit is set by software the LCDIF will begin transferring data between the SoC and the display" "0,1" line.long 0x8 "CTRL_CLR,LCDIF General Control Register" bitfld.long 0x8 31. "SFTRST,This bit must be set to zero to enable normal operation of the LCDIF" "0,1" newline bitfld.long 0x8 30. "CLKGATE,This bit must be set to zero for normal operation" "0,1" newline bitfld.long 0x8 26. "DATA_SHIFT_DIR,Use this bit to determine the direction of shift of transmit data." "0: Data to be transmitted is shifted LEFT by..,1: Data to be transmitted is shifted RIGHT by.." newline hexmask.long.byte 0x8 21.--25. 1. "SHIFT_NUM_BITS,The data to be transmitted is shifted left or right by this number of bits." newline bitfld.long 0x8 19. "BYPASS_COUNT,When this bit is 0 it means that LCDIF will stop the block operation and turn off the RUN bit after the amount of data indicated by the LCDIF_TRANSFER_COUNT register has been transferred out" "0,1" newline bitfld.long 0x8 17. "DOTCLK_MODE,Set this bit to 1 to make the hardware go into the DOTCLK mode i" "0,1" newline bitfld.long 0x8 14.--15. "INPUT_DATA_SWIZZLE,This field specifies how to swap the bytes fetched by the bus master interface" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x8 12.--13. "CSC_DATA_SWIZZLE,This field specifies how to swap the bytes after the data has been converted into an internal representation of 24 bits per pixel and before it is transmitted over the LCD interface bus" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0x8 10.--11. "LCD_DATABUS_WIDTH,LCD Data bus transfer width. When LUT enabled this field should be set to 0x01." "0: 16-bit data bus mode.,1: 8-bit data bus mode.,2: 18-bit data bus mode.,3: 24-bit data bus mode." newline bitfld.long 0x8 8.--9. "WORD_LENGTH,Input data format." "0: Input data is 16 bits per pixel.,1: Input data is 8 bits wide.,2: Input data is 18 bits per pixel.,3: Input data is 24 bits per pixel." newline bitfld.long 0x8 6. "ENABLE_PXP_HANDSHAKE,If this bit is set and LCDIF_MASTER bit is set the LCDIF will act as bus master and the handshake mechanism between LCDIF and PXP will be turned on" "0,1" newline bitfld.long 0x8 5. "MASTER,Set this bit to make the LCDIF act as a bus master" "0,1" newline bitfld.long 0x8 3. "DATA_FORMAT_16_BIT,When this bit is 1 and WORD_LENGTH = 0 it implies that the 16-bit data is in ARGB555 format" "0,1" newline bitfld.long 0x8 2. "DATA_FORMAT_18_BIT,Used only when WORD_LENGTH = 2 i.e. 18-bit." "0: Data input to the block is in 18 bpp format such..,1: Data input to the block is in 18 bpp format such.." newline bitfld.long 0x8 1. "DATA_FORMAT_24_BIT,Used only when WORD_LENGTH = 3 i" "0: Data input to the block is in 24 bpp format such..,1: Data input to the block is actually RGB 18 bpp.." newline bitfld.long 0x8 0. "RUN,When this bit is set by software the LCDIF will begin transferring data between the SoC and the display" "0,1" line.long 0xC "CTRL_TOG,LCDIF General Control Register" bitfld.long 0xC 31. "SFTRST,This bit must be set to zero to enable normal operation of the LCDIF" "0,1" newline bitfld.long 0xC 30. "CLKGATE,This bit must be set to zero for normal operation" "0,1" newline bitfld.long 0xC 26. "DATA_SHIFT_DIR,Use this bit to determine the direction of shift of transmit data." "0: Data to be transmitted is shifted LEFT by..,1: Data to be transmitted is shifted RIGHT by.." newline hexmask.long.byte 0xC 21.--25. 1. "SHIFT_NUM_BITS,The data to be transmitted is shifted left or right by this number of bits." newline bitfld.long 0xC 19. "BYPASS_COUNT,When this bit is 0 it means that LCDIF will stop the block operation and turn off the RUN bit after the amount of data indicated by the LCDIF_TRANSFER_COUNT register has been transferred out" "0,1" newline bitfld.long 0xC 17. "DOTCLK_MODE,Set this bit to 1 to make the hardware go into the DOTCLK mode i" "0,1" newline bitfld.long 0xC 14.--15. "INPUT_DATA_SWIZZLE,This field specifies how to swap the bytes fetched by the bus master interface" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0xC 12.--13. "CSC_DATA_SWIZZLE,This field specifies how to swap the bytes after the data has been converted into an internal representation of 24 bits per pixel and before it is transmitted over the LCD interface bus" "0: No byte swapping.(Little endian),1: Big Endian swap (swap bytes 0 3 and 1 2).,2: Swap half-words.,3: Swap bytes within each half-word." newline bitfld.long 0xC 10.--11. "LCD_DATABUS_WIDTH,LCD Data bus transfer width. When LUT enabled this field should be set to 0x01." "0: 16-bit data bus mode.,1: 8-bit data bus mode.,2: 18-bit data bus mode.,3: 24-bit data bus mode." newline bitfld.long 0xC 8.--9. "WORD_LENGTH,Input data format." "0: Input data is 16 bits per pixel.,1: Input data is 8 bits wide.,2: Input data is 18 bits per pixel.,3: Input data is 24 bits per pixel." newline bitfld.long 0xC 6. "ENABLE_PXP_HANDSHAKE,If this bit is set and LCDIF_MASTER bit is set the LCDIF will act as bus master and the handshake mechanism between LCDIF and PXP will be turned on" "0,1" newline bitfld.long 0xC 5. "MASTER,Set this bit to make the LCDIF act as a bus master" "0,1" newline bitfld.long 0xC 3. "DATA_FORMAT_16_BIT,When this bit is 1 and WORD_LENGTH = 0 it implies that the 16-bit data is in ARGB555 format" "0,1" newline bitfld.long 0xC 2. "DATA_FORMAT_18_BIT,Used only when WORD_LENGTH = 2 i.e. 18-bit." "0: Data input to the block is in 18 bpp format such..,1: Data input to the block is in 18 bpp format such.." newline bitfld.long 0xC 1. "DATA_FORMAT_24_BIT,Used only when WORD_LENGTH = 3 i" "0: Data input to the block is in 24 bpp format such..,1: Data input to the block is actually RGB 18 bpp.." newline bitfld.long 0xC 0. "RUN,When this bit is set by software the LCDIF will begin transferring data between the SoC and the display" "0,1" line.long 0x10 "CTRL1,LCDIF General Control1 Register" bitfld.long 0x10 31. "IMAGE_DATA_SELECT,Command Mode MIPI image data select bit" "0,1" newline bitfld.long 0x10 30. "CS_OUT_SELECT,This bit is CS0/CS1 valid select signals" "0,1" newline bitfld.long 0x10 26. "BM_ERROR_IRQ_EN,This bit is set to enable bus master error interrupt in the LCDIF master mode." "0,1" newline bitfld.long 0x10 25. "BM_ERROR_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x10 24. "RECOVER_ON_UNDERFLOW,Set this bit to enable the LCDIF block to recover in the next field/frame if there was an underflow in the current field/frame" "0,1" newline bitfld.long 0x10 23. "INTERLACE_FIELDS,Set this bit if it is required that the LCDIF block fetches odd lines in one field and even lines in the other field" "0,1" newline bitfld.long 0x10 22. "START_INTERLACE_FROM_SECOND_FIELD,The default is to grab the odd lines first and then the even lines" "0,1" newline bitfld.long 0x10 21. "FIFO_CLEAR,Set this bit to clear all the data in the latency FIFO (LFIFO) TXFIFO and the RXFIFO." "0,1" newline bitfld.long 0x10 20. "IRQ_ON_ALTERNATE_FIELDS,If this bit is set the LCDIF block will assert the cur_frame_done interrupt only on alternate fields otherwise it will issue the interrupt on both odd and even field" "0,1" newline hexmask.long.byte 0x10 16.--19. 1. "BYTE_PACKING_FORMAT,This bitfield is used to show which data bytes in a 32-bit word are valid" newline bitfld.long 0x10 15. "OVERFLOW_IRQ_EN,This bit is set to enable an overflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x10 14. "UNDERFLOW_IRQ_EN,This bit is set to enable an underflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x10 13. "CUR_FRAME_DONE_IRQ_EN,This bit is set to 1 enable an interrupt every time the hardware enters in the vertical blanking state" "0,1" newline bitfld.long 0x10 12. "VSYNC_EDGE_IRQ_EN,This bit is set to enable an interrupt every time the hardware encounters the leading VSYNC edge in the VSYNC and DOTCLK modes or the beginning of every field in DVI mode" "0,1" newline bitfld.long 0x10 11. "OVERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x10 10. "UNDERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x10 9. "CUR_FRAME_DONE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x10 8. "VSYNC_EDGE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." line.long 0x14 "CTRL1_SET,LCDIF General Control1 Register" bitfld.long 0x14 31. "IMAGE_DATA_SELECT,Command Mode MIPI image data select bit" "0,1" newline bitfld.long 0x14 30. "CS_OUT_SELECT,This bit is CS0/CS1 valid select signals" "0,1" newline bitfld.long 0x14 26. "BM_ERROR_IRQ_EN,This bit is set to enable bus master error interrupt in the LCDIF master mode." "0,1" newline bitfld.long 0x14 25. "BM_ERROR_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x14 24. "RECOVER_ON_UNDERFLOW,Set this bit to enable the LCDIF block to recover in the next field/frame if there was an underflow in the current field/frame" "0,1" newline bitfld.long 0x14 23. "INTERLACE_FIELDS,Set this bit if it is required that the LCDIF block fetches odd lines in one field and even lines in the other field" "0,1" newline bitfld.long 0x14 22. "START_INTERLACE_FROM_SECOND_FIELD,The default is to grab the odd lines first and then the even lines" "0,1" newline bitfld.long 0x14 21. "FIFO_CLEAR,Set this bit to clear all the data in the latency FIFO (LFIFO) TXFIFO and the RXFIFO." "0,1" newline bitfld.long 0x14 20. "IRQ_ON_ALTERNATE_FIELDS,If this bit is set the LCDIF block will assert the cur_frame_done interrupt only on alternate fields otherwise it will issue the interrupt on both odd and even field" "0,1" newline hexmask.long.byte 0x14 16.--19. 1. "BYTE_PACKING_FORMAT,This bitfield is used to show which data bytes in a 32-bit word are valid" newline bitfld.long 0x14 15. "OVERFLOW_IRQ_EN,This bit is set to enable an overflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x14 14. "UNDERFLOW_IRQ_EN,This bit is set to enable an underflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x14 13. "CUR_FRAME_DONE_IRQ_EN,This bit is set to 1 enable an interrupt every time the hardware enters in the vertical blanking state" "0,1" newline bitfld.long 0x14 12. "VSYNC_EDGE_IRQ_EN,This bit is set to enable an interrupt every time the hardware encounters the leading VSYNC edge in the VSYNC and DOTCLK modes or the beginning of every field in DVI mode" "0,1" newline bitfld.long 0x14 11. "OVERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x14 10. "UNDERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x14 9. "CUR_FRAME_DONE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x14 8. "VSYNC_EDGE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." line.long 0x18 "CTRL1_CLR,LCDIF General Control1 Register" bitfld.long 0x18 31. "IMAGE_DATA_SELECT,Command Mode MIPI image data select bit" "0,1" newline bitfld.long 0x18 30. "CS_OUT_SELECT,This bit is CS0/CS1 valid select signals" "0,1" newline bitfld.long 0x18 26. "BM_ERROR_IRQ_EN,This bit is set to enable bus master error interrupt in the LCDIF master mode." "0,1" newline bitfld.long 0x18 25. "BM_ERROR_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x18 24. "RECOVER_ON_UNDERFLOW,Set this bit to enable the LCDIF block to recover in the next field/frame if there was an underflow in the current field/frame" "0,1" newline bitfld.long 0x18 23. "INTERLACE_FIELDS,Set this bit if it is required that the LCDIF block fetches odd lines in one field and even lines in the other field" "0,1" newline bitfld.long 0x18 22. "START_INTERLACE_FROM_SECOND_FIELD,The default is to grab the odd lines first and then the even lines" "0,1" newline bitfld.long 0x18 21. "FIFO_CLEAR,Set this bit to clear all the data in the latency FIFO (LFIFO) TXFIFO and the RXFIFO." "0,1" newline bitfld.long 0x18 20. "IRQ_ON_ALTERNATE_FIELDS,If this bit is set the LCDIF block will assert the cur_frame_done interrupt only on alternate fields otherwise it will issue the interrupt on both odd and even field" "0,1" newline hexmask.long.byte 0x18 16.--19. 1. "BYTE_PACKING_FORMAT,This bitfield is used to show which data bytes in a 32-bit word are valid" newline bitfld.long 0x18 15. "OVERFLOW_IRQ_EN,This bit is set to enable an overflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x18 14. "UNDERFLOW_IRQ_EN,This bit is set to enable an underflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x18 13. "CUR_FRAME_DONE_IRQ_EN,This bit is set to 1 enable an interrupt every time the hardware enters in the vertical blanking state" "0,1" newline bitfld.long 0x18 12. "VSYNC_EDGE_IRQ_EN,This bit is set to enable an interrupt every time the hardware encounters the leading VSYNC edge in the VSYNC and DOTCLK modes or the beginning of every field in DVI mode" "0,1" newline bitfld.long 0x18 11. "OVERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x18 10. "UNDERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x18 9. "CUR_FRAME_DONE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x18 8. "VSYNC_EDGE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." line.long 0x1C "CTRL1_TOG,LCDIF General Control1 Register" bitfld.long 0x1C 31. "IMAGE_DATA_SELECT,Command Mode MIPI image data select bit" "0,1" newline bitfld.long 0x1C 30. "CS_OUT_SELECT,This bit is CS0/CS1 valid select signals" "0,1" newline bitfld.long 0x1C 26. "BM_ERROR_IRQ_EN,This bit is set to enable bus master error interrupt in the LCDIF master mode." "0,1" newline bitfld.long 0x1C 25. "BM_ERROR_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x1C 24. "RECOVER_ON_UNDERFLOW,Set this bit to enable the LCDIF block to recover in the next field/frame if there was an underflow in the current field/frame" "0,1" newline bitfld.long 0x1C 23. "INTERLACE_FIELDS,Set this bit if it is required that the LCDIF block fetches odd lines in one field and even lines in the other field" "0,1" newline bitfld.long 0x1C 22. "START_INTERLACE_FROM_SECOND_FIELD,The default is to grab the odd lines first and then the even lines" "0,1" newline bitfld.long 0x1C 21. "FIFO_CLEAR,Set this bit to clear all the data in the latency FIFO (LFIFO) TXFIFO and the RXFIFO." "0,1" newline bitfld.long 0x1C 20. "IRQ_ON_ALTERNATE_FIELDS,If this bit is set the LCDIF block will assert the cur_frame_done interrupt only on alternate fields otherwise it will issue the interrupt on both odd and even field" "0,1" newline hexmask.long.byte 0x1C 16.--19. 1. "BYTE_PACKING_FORMAT,This bitfield is used to show which data bytes in a 32-bit word are valid" newline bitfld.long 0x1C 15. "OVERFLOW_IRQ_EN,This bit is set to enable an overflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x1C 14. "UNDERFLOW_IRQ_EN,This bit is set to enable an underflow interrupt in the TXFIFO in the write mode." "0,1" newline bitfld.long 0x1C 13. "CUR_FRAME_DONE_IRQ_EN,This bit is set to 1 enable an interrupt every time the hardware enters in the vertical blanking state" "0,1" newline bitfld.long 0x1C 12. "VSYNC_EDGE_IRQ_EN,This bit is set to enable an interrupt every time the hardware encounters the leading VSYNC edge in the VSYNC and DOTCLK modes or the beginning of every field in DVI mode" "0,1" newline bitfld.long 0x1C 11. "OVERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x1C 10. "UNDERFLOW_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x1C 9. "CUR_FRAME_DONE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." newline bitfld.long 0x1C 8. "VSYNC_EDGE_IRQ,This bit is set to indicate that an interrupt is requested by the LCDIF block" "0: No Interrupt Request Pending.,1: Interrupt Request Pending." line.long 0x20 "CTRL2,LCDIF General Control2 Register" bitfld.long 0x20 21.--23. "OUTSTANDING_REQS,This bitfield indicates the maximum number of outstanding transactions that LCDIF should request when it is acting as a bus master" "0: REQ_1,1: REQ_2,2: REQ_4,3: REQ_8,4: REQ_16,?,?,?" newline bitfld.long 0x20 20. "BURST_LEN_8,By default when the LCDIF is in the bus master mode it will issue AXI bursts of length 16 (except when in packed 24 bpp mode it will issue bursts of length 15)" "0,1" newline bitfld.long 0x20 16.--18. "ODD_LINE_PATTERN,This field determines the order of the RGB components of each pixel in ODD lines (line numbers 1 3 5 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" newline bitfld.long 0x20 12.--14. "EVEN_LINE_PATTERN,This field determines the order of the RGB components of each pixel in EVEN lines (line numbers 2 4 6 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" line.long 0x24 "CTRL2_SET,LCDIF General Control2 Register" bitfld.long 0x24 21.--23. "OUTSTANDING_REQS,This bitfield indicates the maximum number of outstanding transactions that LCDIF should request when it is acting as a bus master" "0: REQ_1,1: REQ_2,2: REQ_4,3: REQ_8,4: REQ_16,?,?,?" newline bitfld.long 0x24 20. "BURST_LEN_8,By default when the LCDIF is in the bus master mode it will issue AXI bursts of length 16 (except when in packed 24 bpp mode it will issue bursts of length 15)" "0,1" newline bitfld.long 0x24 16.--18. "ODD_LINE_PATTERN,This field determines the order of the RGB components of each pixel in ODD lines (line numbers 1 3 5 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" newline bitfld.long 0x24 12.--14. "EVEN_LINE_PATTERN,This field determines the order of the RGB components of each pixel in EVEN lines (line numbers 2 4 6 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" line.long 0x28 "CTRL2_CLR,LCDIF General Control2 Register" bitfld.long 0x28 21.--23. "OUTSTANDING_REQS,This bitfield indicates the maximum number of outstanding transactions that LCDIF should request when it is acting as a bus master" "0: REQ_1,1: REQ_2,2: REQ_4,3: REQ_8,4: REQ_16,?,?,?" newline bitfld.long 0x28 20. "BURST_LEN_8,By default when the LCDIF is in the bus master mode it will issue AXI bursts of length 16 (except when in packed 24 bpp mode it will issue bursts of length 15)" "0,1" newline bitfld.long 0x28 16.--18. "ODD_LINE_PATTERN,This field determines the order of the RGB components of each pixel in ODD lines (line numbers 1 3 5 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" newline bitfld.long 0x28 12.--14. "EVEN_LINE_PATTERN,This field determines the order of the RGB components of each pixel in EVEN lines (line numbers 2 4 6 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" line.long 0x2C "CTRL2_TOG,LCDIF General Control2 Register" bitfld.long 0x2C 21.--23. "OUTSTANDING_REQS,This bitfield indicates the maximum number of outstanding transactions that LCDIF should request when it is acting as a bus master" "0: REQ_1,1: REQ_2,2: REQ_4,3: REQ_8,4: REQ_16,?,?,?" newline bitfld.long 0x2C 20. "BURST_LEN_8,By default when the LCDIF is in the bus master mode it will issue AXI bursts of length 16 (except when in packed 24 bpp mode it will issue bursts of length 15)" "0,1" newline bitfld.long 0x2C 16.--18. "ODD_LINE_PATTERN,This field determines the order of the RGB components of each pixel in ODD lines (line numbers 1 3 5 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" newline bitfld.long 0x2C 12.--14. "EVEN_LINE_PATTERN,This field determines the order of the RGB components of each pixel in EVEN lines (line numbers 2 4 6 " "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" line.long 0x30 "TRANSFER_COUNT,LCDIF Horizontal and Vertical Valid Data Count Register" hexmask.long.word 0x30 16.--31. 1. "V_COUNT,Number of horizontal lines per frame which contain valid data" newline hexmask.long.word 0x30 0.--15. 1. "H_COUNT,Total valid data (pixels) in each horizontal line" group.long 0x40++0x3 line.long 0x0 "CUR_BUF,LCD Interface Current Buffer Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address of the current frame being transmitted by LCDIF." group.long 0x50++0x3 line.long 0x0 "NEXT_BUF,LCD Interface Next Buffer Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address of the next frame that will be transmitted by LCDIF." group.long 0x70++0x13 line.long 0x0 "VDCTRL0,LCDIF VSYNC Mode and Dotclk Mode Control Register0" bitfld.long 0x0 29. "VSYNC_OEB,0 means the VSYNC signal is an output 1 means it is an input" "0: The VSYNC pin is in the output mode and the..,1: The VSYNC pin is in the input mode and the LCD.." newline bitfld.long 0x0 28. "ENABLE_PRESENT,Setting this bit to 1 will make the hardware generate the ENABLE signal in the DOTCLK mode thereby making it the true RGB interface along with the remaining three signals VSYNC HSYNC and DOTCLK" "0,1" newline bitfld.long 0x0 27. "VSYNC_POL,Default 0 active low during VSYNC_PULSE_WIDTH time and will be high during the rest of the VSYNC period" "0,1" newline bitfld.long 0x0 26. "HSYNC_POL,Default 0 active low during HSYNC_PULSE_WIDTH time and will be high during the rest of the HSYNC period" "0,1" newline bitfld.long 0x0 25. "DOTCLK_POL,Default is data launched at negative edge of DOTCLK and captured at positive edge" "0,1" newline bitfld.long 0x0 24. "ENABLE_POL,Default 0 active low during valid data transfer on each horizontal line." "0,1" newline bitfld.long 0x0 21. "VSYNC_PERIOD_UNIT,Default 0 for counting VSYNC_PERIOD in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x0 20. "VSYNC_PULSE_WIDTH_UNIT,Default 0 for counting VSYNC_PULSE_WIDTH in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x0 19. "HALF_LINE,Setting this bit to 1 will make the total VSYNC period equal to the VSYNC_PERIOD field plus half the HORIZONTAL_PERIOD field (i" "0,1" newline bitfld.long 0x0 18. "HALF_LINE_MODE,When this bit is 0 the first field (VSYNC period) will end in half a horizontal line and the second field will begin with half a horizontal line" "0,1" newline hexmask.long.tbyte 0x0 0.--17. 1. "VSYNC_PULSE_WIDTH,Number of units for which VSYNC signal is active" line.long 0x4 "VDCTRL0_SET,LCDIF VSYNC Mode and Dotclk Mode Control Register0" bitfld.long 0x4 29. "VSYNC_OEB,0 means the VSYNC signal is an output 1 means it is an input" "0: The VSYNC pin is in the output mode and the..,1: The VSYNC pin is in the input mode and the LCD.." newline bitfld.long 0x4 28. "ENABLE_PRESENT,Setting this bit to 1 will make the hardware generate the ENABLE signal in the DOTCLK mode thereby making it the true RGB interface along with the remaining three signals VSYNC HSYNC and DOTCLK" "0,1" newline bitfld.long 0x4 27. "VSYNC_POL,Default 0 active low during VSYNC_PULSE_WIDTH time and will be high during the rest of the VSYNC period" "0,1" newline bitfld.long 0x4 26. "HSYNC_POL,Default 0 active low during HSYNC_PULSE_WIDTH time and will be high during the rest of the HSYNC period" "0,1" newline bitfld.long 0x4 25. "DOTCLK_POL,Default is data launched at negative edge of DOTCLK and captured at positive edge" "0,1" newline bitfld.long 0x4 24. "ENABLE_POL,Default 0 active low during valid data transfer on each horizontal line." "0,1" newline bitfld.long 0x4 21. "VSYNC_PERIOD_UNIT,Default 0 for counting VSYNC_PERIOD in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x4 20. "VSYNC_PULSE_WIDTH_UNIT,Default 0 for counting VSYNC_PULSE_WIDTH in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x4 19. "HALF_LINE,Setting this bit to 1 will make the total VSYNC period equal to the VSYNC_PERIOD field plus half the HORIZONTAL_PERIOD field (i" "0,1" newline bitfld.long 0x4 18. "HALF_LINE_MODE,When this bit is 0 the first field (VSYNC period) will end in half a horizontal line and the second field will begin with half a horizontal line" "0,1" newline hexmask.long.tbyte 0x4 0.--17. 1. "VSYNC_PULSE_WIDTH,Number of units for which VSYNC signal is active" line.long 0x8 "VDCTRL0_CLR,LCDIF VSYNC Mode and Dotclk Mode Control Register0" bitfld.long 0x8 29. "VSYNC_OEB,0 means the VSYNC signal is an output 1 means it is an input" "0: The VSYNC pin is in the output mode and the..,1: The VSYNC pin is in the input mode and the LCD.." newline bitfld.long 0x8 28. "ENABLE_PRESENT,Setting this bit to 1 will make the hardware generate the ENABLE signal in the DOTCLK mode thereby making it the true RGB interface along with the remaining three signals VSYNC HSYNC and DOTCLK" "0,1" newline bitfld.long 0x8 27. "VSYNC_POL,Default 0 active low during VSYNC_PULSE_WIDTH time and will be high during the rest of the VSYNC period" "0,1" newline bitfld.long 0x8 26. "HSYNC_POL,Default 0 active low during HSYNC_PULSE_WIDTH time and will be high during the rest of the HSYNC period" "0,1" newline bitfld.long 0x8 25. "DOTCLK_POL,Default is data launched at negative edge of DOTCLK and captured at positive edge" "0,1" newline bitfld.long 0x8 24. "ENABLE_POL,Default 0 active low during valid data transfer on each horizontal line." "0,1" newline bitfld.long 0x8 21. "VSYNC_PERIOD_UNIT,Default 0 for counting VSYNC_PERIOD in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x8 20. "VSYNC_PULSE_WIDTH_UNIT,Default 0 for counting VSYNC_PULSE_WIDTH in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0x8 19. "HALF_LINE,Setting this bit to 1 will make the total VSYNC period equal to the VSYNC_PERIOD field plus half the HORIZONTAL_PERIOD field (i" "0,1" newline bitfld.long 0x8 18. "HALF_LINE_MODE,When this bit is 0 the first field (VSYNC period) will end in half a horizontal line and the second field will begin with half a horizontal line" "0,1" newline hexmask.long.tbyte 0x8 0.--17. 1. "VSYNC_PULSE_WIDTH,Number of units for which VSYNC signal is active" line.long 0xC "VDCTRL0_TOG,LCDIF VSYNC Mode and Dotclk Mode Control Register0" bitfld.long 0xC 29. "VSYNC_OEB,0 means the VSYNC signal is an output 1 means it is an input" "0: The VSYNC pin is in the output mode and the..,1: The VSYNC pin is in the input mode and the LCD.." newline bitfld.long 0xC 28. "ENABLE_PRESENT,Setting this bit to 1 will make the hardware generate the ENABLE signal in the DOTCLK mode thereby making it the true RGB interface along with the remaining three signals VSYNC HSYNC and DOTCLK" "0,1" newline bitfld.long 0xC 27. "VSYNC_POL,Default 0 active low during VSYNC_PULSE_WIDTH time and will be high during the rest of the VSYNC period" "0,1" newline bitfld.long 0xC 26. "HSYNC_POL,Default 0 active low during HSYNC_PULSE_WIDTH time and will be high during the rest of the HSYNC period" "0,1" newline bitfld.long 0xC 25. "DOTCLK_POL,Default is data launched at negative edge of DOTCLK and captured at positive edge" "0,1" newline bitfld.long 0xC 24. "ENABLE_POL,Default 0 active low during valid data transfer on each horizontal line." "0,1" newline bitfld.long 0xC 21. "VSYNC_PERIOD_UNIT,Default 0 for counting VSYNC_PERIOD in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0xC 20. "VSYNC_PULSE_WIDTH_UNIT,Default 0 for counting VSYNC_PULSE_WIDTH in terms of DISPLAY CLOCK (pix_clk) cycles" "0,1" newline bitfld.long 0xC 19. "HALF_LINE,Setting this bit to 1 will make the total VSYNC period equal to the VSYNC_PERIOD field plus half the HORIZONTAL_PERIOD field (i" "0,1" newline bitfld.long 0xC 18. "HALF_LINE_MODE,When this bit is 0 the first field (VSYNC period) will end in half a horizontal line and the second field will begin with half a horizontal line" "0,1" newline hexmask.long.tbyte 0xC 0.--17. 1. "VSYNC_PULSE_WIDTH,Number of units for which VSYNC signal is active" line.long 0x10 "VDCTRL1,LCDIF VSYNC Mode and Dotclk Mode Control Register1" hexmask.long 0x10 0.--31. 1. "VSYNC_PERIOD,Total number of units between two positive or two negative edges of the VSYNC signal" group.long 0x90++0x3 line.long 0x0 "VDCTRL2,LCDIF VSYNC Mode and Dotclk Mode Control Register2" hexmask.long.word 0x0 18.--31. 1. "HSYNC_PULSE_WIDTH,Number of DISPLAY CLOCK (pix_clk) cycles for which HSYNC signal is active." newline hexmask.long.tbyte 0x0 0.--17. 1. "HSYNC_PERIOD,Total number of DISPLAY CLOCK (pix_clk) cycles between two positive or two negative edges of the HSYNC signal" group.long 0xA0++0x3 line.long 0x0 "VDCTRL3,LCDIF VSYNC Mode and Dotclk Mode Control Register3" bitfld.long 0x0 29. "MUX_SYNC_SIGNALS,When this bit is set the LCDIF block will internally mux HSYNC with LCD_D14 DOTCLK with LCD_D13 and ENABLE with LCD_D12 otherwise these signals will go out on separate pins" "0,1" newline bitfld.long 0x0 28. "VSYNC_ONLY,This bit must be set to 1 in the VSYNC mode of operation and 0 in the DOTCLK mode of operation." "0,1" newline hexmask.long.word 0x0 16.--27. 1. "HORIZONTAL_WAIT_CNT,In the DOTCLK mode wait for this number of clocks from falling edge (or rising if HSYNC_POL is 1) of HSYNC signal to account for horizontal back porch plus the number of DOTCLKs before the moving picture information begins" newline hexmask.long.word 0x0 0.--15. 1. "VERTICAL_WAIT_CNT,In the VSYNC interface mode wait for this number of DISPLAY CLOCK (pix_clk) cycles from the falling VSYNC edge (or rising if VSYNC_POL is 1) before starting LCD transactions and is applicable only if WAIT_FOR_VSYNC_EDGE is set" group.long 0xB0++0x3 line.long 0x0 "VDCTRL4,LCDIF VSYNC Mode and Dotclk Mode Control Register4" bitfld.long 0x0 29.--31. "DOTCLK_DLY_SEL,This bitfield selects the amount of time by which the DOTCLK signal should be delayed before coming out of the LCD_DOTCK pin" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18. "SYNC_SIGNALS_ON,Set this field to 1 if the LCD controller requires that the VSYNC or VSYNC/HSYNC/DOTCLK control signals should be active at least one frame before the data transfers actually start and remain active at least one frame after the data.." "0,1" newline hexmask.long.tbyte 0x0 0.--17. 1. "DOTCLK_H_VALID_DATA_CNT,Total number of DISPLAY CLOCK (pix_clk) cycles on each horizontal line that carry valid data in DOTCLK mode" group.long 0x190++0x3 line.long 0x0 "BM_ERROR_STAT,Bus Master Error Status Register" hexmask.long 0x0 0.--31. 1. "ADDR,Virtual address at which bus master error occurred." group.long 0x1A0++0x3 line.long 0x0 "CRC_STAT,CRC Status Register" hexmask.long 0x0 0.--31. 1. "CRC_VALUE,Calculated CRC value." rgroup.long 0x1B0++0x3 line.long 0x0 "STAT,LCD Interface Status Register" bitfld.long 0x0 31. "PRESENT,0: LCDIF not present on this product 1: LCDIF is present." "0: LCDIF not present on this product,1: LCDIF is present" newline bitfld.long 0x0 30. "DMA_REQ,Reflects the current state of the DMA Request line for the LCDIF" "0,1" newline bitfld.long 0x0 29. "LFIFO_FULL,Read only view of the signals that indicates LCD LFIFO is full." "0,1" newline bitfld.long 0x0 28. "LFIFO_EMPTY,Read only view of the signals that indicates LCD LFIFO is empty." "0,1" newline bitfld.long 0x0 27. "TXFIFO_FULL,Read only view of the signals that indicates LCD TXFIFO is full." "0,1" newline bitfld.long 0x0 26. "TXFIFO_EMPTY,Read only view of the signals that indicates LCD TXFIFO is empty." "0,1" newline hexmask.long.word 0x0 0.--8. 1. "LFIFO_COUNT,Read only view of the current count in Latency buffer (LFIFO)." group.long 0x200++0x3 line.long 0x0 "THRES,LCDIF Threshold Register" hexmask.long.word 0x0 16.--24. 1. "FASTCLOCK,This value should be set to a value of pixels from 0 to 511" group.long 0x380++0x2F line.long 0x0 "PIGEONCTRL0,LCDIF Pigeon Mode Control0 Register" hexmask.long.word 0x0 16.--27. 1. "LD_PERIOD,Period of pclk counter during LD phase" newline hexmask.long.word 0x0 0.--11. 1. "FD_PERIOD,Period of line counter during FD phase" line.long 0x4 "PIGEONCTRL0_SET,LCDIF Pigeon Mode Control0 Register" hexmask.long.word 0x4 16.--27. 1. "LD_PERIOD,Period of pclk counter during LD phase" newline hexmask.long.word 0x4 0.--11. 1. "FD_PERIOD,Period of line counter during FD phase" line.long 0x8 "PIGEONCTRL0_CLR,LCDIF Pigeon Mode Control0 Register" hexmask.long.word 0x8 16.--27. 1. "LD_PERIOD,Period of pclk counter during LD phase" newline hexmask.long.word 0x8 0.--11. 1. "FD_PERIOD,Period of line counter during FD phase" line.long 0xC "PIGEONCTRL0_TOG,LCDIF Pigeon Mode Control0 Register" hexmask.long.word 0xC 16.--27. 1. "LD_PERIOD,Period of pclk counter during LD phase" newline hexmask.long.word 0xC 0.--11. 1. "FD_PERIOD,Period of line counter during FD phase" line.long 0x10 "PIGEONCTRL1,LCDIF Pigeon Mode Control1 Register" hexmask.long.word 0x10 16.--27. 1. "FRAME_CNT_CYCLES,Max cycles of frame counter" newline hexmask.long.word 0x10 0.--11. 1. "FRAME_CNT_PERIOD,Period of frame counter" line.long 0x14 "PIGEONCTRL1_SET,LCDIF Pigeon Mode Control1 Register" hexmask.long.word 0x14 16.--27. 1. "FRAME_CNT_CYCLES,Max cycles of frame counter" newline hexmask.long.word 0x14 0.--11. 1. "FRAME_CNT_PERIOD,Period of frame counter" line.long 0x18 "PIGEONCTRL1_CLR,LCDIF Pigeon Mode Control1 Register" hexmask.long.word 0x18 16.--27. 1. "FRAME_CNT_CYCLES,Max cycles of frame counter" newline hexmask.long.word 0x18 0.--11. 1. "FRAME_CNT_PERIOD,Period of frame counter" line.long 0x1C "PIGEONCTRL1_TOG,LCDIF Pigeon Mode Control1 Register" hexmask.long.word 0x1C 16.--27. 1. "FRAME_CNT_CYCLES,Max cycles of frame counter" newline hexmask.long.word 0x1C 0.--11. 1. "FRAME_CNT_PERIOD,Period of frame counter" line.long 0x20 "PIGEONCTRL2,LCDIF Pigeon Mode Control2 Register" bitfld.long 0x20 1. "PIGEON_CLK_GATE,Pigeon mode dot clock gate enable" "0,1" newline bitfld.long 0x20 0. "PIGEON_DATA_EN,Pigeon mode data enable" "0,1" line.long 0x24 "PIGEONCTRL2_SET,LCDIF Pigeon Mode Control2 Register" bitfld.long 0x24 1. "PIGEON_CLK_GATE,Pigeon mode dot clock gate enable" "0,1" newline bitfld.long 0x24 0. "PIGEON_DATA_EN,Pigeon mode data enable" "0,1" line.long 0x28 "PIGEONCTRL2_CLR,LCDIF Pigeon Mode Control2 Register" bitfld.long 0x28 1. "PIGEON_CLK_GATE,Pigeon mode dot clock gate enable" "0,1" newline bitfld.long 0x28 0. "PIGEON_DATA_EN,Pigeon mode data enable" "0,1" line.long 0x2C "PIGEONCTRL2_TOG,LCDIF Pigeon Mode Control2 Register" bitfld.long 0x2C 1. "PIGEON_CLK_GATE,Pigeon mode dot clock gate enable" "0,1" newline bitfld.long 0x2C 0. "PIGEON_DATA_EN,Pigeon mode data enable" "0,1" group.long 0x800++0x3 line.long 0x0 "PIGEON_0_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x810++0x3 line.long 0x0 "PIGEON_0_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x820++0x3 line.long 0x0 "PIGEON_0_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x840++0x3 line.long 0x0 "PIGEON_1_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x850++0x3 line.long 0x0 "PIGEON_1_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x860++0x3 line.long 0x0 "PIGEON_1_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x880++0x3 line.long 0x0 "PIGEON_2_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x890++0x3 line.long 0x0 "PIGEON_2_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x8A0++0x3 line.long 0x0 "PIGEON_2_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x8C0++0x3 line.long 0x0 "PIGEON_3_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x8D0++0x3 line.long 0x0 "PIGEON_3_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x8E0++0x3 line.long 0x0 "PIGEON_3_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x900++0x3 line.long 0x0 "PIGEON_4_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x910++0x3 line.long 0x0 "PIGEON_4_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x920++0x3 line.long 0x0 "PIGEON_4_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x940++0x3 line.long 0x0 "PIGEON_5_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x950++0x3 line.long 0x0 "PIGEON_5_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x960++0x3 line.long 0x0 "PIGEON_5_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x980++0x3 line.long 0x0 "PIGEON_6_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x990++0x3 line.long 0x0 "PIGEON_6_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x9A0++0x3 line.long 0x0 "PIGEON_6_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0x9C0++0x3 line.long 0x0 "PIGEON_7_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0x9D0++0x3 line.long 0x0 "PIGEON_7_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0x9E0++0x3 line.long 0x0 "PIGEON_7_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0xA00++0x3 line.long 0x0 "PIGEON_8_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0xA10++0x3 line.long 0x0 "PIGEON_8_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0xA20++0x3 line.long 0x0 "PIGEON_8_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0xA40++0x3 line.long 0x0 "PIGEON_9_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0xA50++0x3 line.long 0x0 "PIGEON_9_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0xA60++0x3 line.long 0x0 "PIGEON_9_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0xA80++0x3 line.long 0x0 "PIGEON_10_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0xA90++0x3 line.long 0x0 "PIGEON_10_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0xAA0++0x3 line.long 0x0 "PIGEON_10_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0xAC0++0x3 line.long 0x0 "PIGEON_11_0,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 24.--31. 1. "STATE_MASK,state_mask = (FS|FB|FD|FE) and (LS|LB|LD|LE) select any combination of scan states as reference point for local counter to start ticking" newline hexmask.long.word 0x0 12.--23. 1. "MASK_CNT,When the global counter selected through MASK_CNT_SEL matches value in this reg pigeon local counter start ticking" newline hexmask.long.byte 0x0 8.--11. 1. "MASK_CNT_SEL,select global counters as mask condition use together with MASK_CNT" newline hexmask.long.byte 0x0 4.--7. 1. "OFFSET,offset on pclk unit" newline bitfld.long 0x0 2.--3. "INC_SEL,Event to incrment local counter" "0: pclk,1: Line start pulse,2: Frame start pulse,3: Use another signal as tick event" newline bitfld.long 0x0 1. "POL,Polarity of signal output" "0: Normal Signal (Active high),1: Inverted signal (Active low)" newline bitfld.long 0x0 0. "EN,Enable pigeon Mode on this signal" "0,1" group.long 0xAD0++0x3 line.long 0x0 "PIGEON_11_1,Panel Interface Signal Generator Register" hexmask.long.word 0x0 16.--31. 1. "CLR_CNT,Deassert signal output when counter match this value" newline hexmask.long.word 0x0 0.--15. 1. "SET_CNT,Assert signal output when counter match this value" group.long 0xAE0++0x3 line.long 0x0 "PIGEON_11_2,Panel Interface Signal Generator Register" hexmask.long.byte 0x0 4.--8. 1. "SIG_ANOTHER,Select another signal for logic operation or as mask or counter tick event" newline hexmask.long.byte 0x0 0.--3. 1. "SIG_LOGIC,Logic operation with another signal: DIS/AND/OR/COND" group.long 0xB00++0x3 line.long 0x0 "LUT_CTRL,Look Up Table Control Register" bitfld.long 0x0 0. "LUT_BYPASS,Setting this bit will bypass the LUT memory resource completely" "0,1" group.long 0xB10++0x3 line.long 0x0 "LUT0_ADDR,Lookup Table 0 Index Register" hexmask.long.byte 0x0 0.--7. 1. "ADDR,LUT indexed address pointer" group.long 0xB20++0x3 line.long 0x0 "LUT0_DATA,Lookup Table 0 Data Register" hexmask.long 0x0 0.--31. 1. "DATA,Writing this field will load 4 bytes aligned to four byte boundaries of data indexed by the ADDR field of the REG_LUT_CTRL register" group.long 0xB30++0x3 line.long 0x0 "LUT1_ADDR,Lookup Table 1 Index Register" hexmask.long.byte 0x0 0.--7. 1. "ADDR,LUT indexed address pointer" group.long 0xB40++0x3 line.long 0x0 "LUT1_DATA,Lookup Table 1 Data Register" hexmask.long 0x0 0.--31. 1. "DATA,Writing this field will load 4 bytes aligned to four byte boundaries of data indexed by the ADDR field of the REG_LUT_CTRL register" tree.end endif tree "LCDIFV2" base ad:0x40808000 group.long 0x0++0x27 line.long 0x0 "CTRL,LCDIFv2 display control Register" bitfld.long 0x0 31. "SW_RESET,Software Reset" "0: No action,1: All LCDIFv2 internal registers are forced into.." newline bitfld.long 0x0 4. "NEG,Indicates if value at the output (pixel data output) needs to be negated" "0: Output is to remain same,1: Output to be negated" newline bitfld.long 0x0 3. "INV_PXCK,Polarity change of Pixel Clock" "0: Display samples data on the falling edge,1: Display samples data on the rising edge" newline bitfld.long 0x0 2. "INV_DE,Invert Data Enable polarity" "0: Data enable is active high,1: Data enable is active low" newline bitfld.long 0x0 1. "INV_VS,Invert Vertical synchronization signal" "0: VSYNC signal not inverted (active HIGH),1: Invert VSYNC signal (active LOW)" newline bitfld.long 0x0 0. "INV_HS,Invert Horizontal synchronization signal" "0: HSYNC signal not inverted (active HIGH),1: Invert HSYNC signal (active LOW)" line.long 0x4 "CTRL_SET,LCDIFv2 display control Register" bitfld.long 0x4 31. "SW_RESET,Software Reset" "0,1" newline bitfld.long 0x4 4. "NEG,Indicates if value at the output (pixel data output) needs to be negated" "0,1" newline bitfld.long 0x4 3. "INV_PXCK,Polarity change of Pixel Clock" "0,1" newline bitfld.long 0x4 2. "INV_DE,Invert Data Enable polarity" "0,1" newline bitfld.long 0x4 1. "INV_VS,Invert Vertical synchronization signal" "0,1" newline bitfld.long 0x4 0. "INV_HS,Invert Horizontal synchronization signal" "0,1" line.long 0x8 "CTRL_CLR,LCDIFv2 display control Register" eventfld.long 0x8 31. "SW_RESET,Software Reset" "0,1" newline eventfld.long 0x8 4. "NEG,Indicates if value at the output (pixel data output) needs to be negated" "0,1" newline eventfld.long 0x8 3. "INV_PXCK,Polarity change of Pixel Clock" "0,1" newline eventfld.long 0x8 2. "INV_DE,Invert Data Enable polarity" "0,1" newline eventfld.long 0x8 1. "INV_VS,Invert Vertical synchronization signal" "0,1" newline eventfld.long 0x8 0. "INV_HS,Invert Horizontal synchronization signal" "0,1" line.long 0xC "CTRL_TOG,LCDIFv2 display control Register" bitfld.long 0xC 31. "SW_RESET,Software Reset" "0,1" newline bitfld.long 0xC 4. "NEG,Indicates if value at the output (pixel data output) needs to be negated" "0,1" newline bitfld.long 0xC 3. "INV_PXCK,Polarity change of Pixel Clock" "0,1" newline bitfld.long 0xC 2. "INV_DE,Invert Data Enable polarity" "0,1" newline bitfld.long 0xC 1. "INV_VS,Invert Vertical synchronization signal" "0,1" newline bitfld.long 0xC 0. "INV_HS,Invert Horizontal synchronization signal" "0,1" line.long 0x10 "DISP_PARA,Display Parameter Register" bitfld.long 0x10 31. "DISP_ON,Display panel On/Off mode" "0: Display Off,1: Display On" newline bitfld.long 0x10 26.--28. "LINE_PATTERN,LCDIFv2 line output order" "0: RGB,1: RBG,2: GBR,3: GRB,4: BRG,5: BGR,?,?" newline bitfld.long 0x10 24.--25. "DISP_MODE,LCDIFv2 operating mode" "0: Normal mode. Panel content controlled by layer..,1: Test Mode1(BGND Color Display),2: Test Mode2(Column Color Bar),3: Test Mode3(Row Color Bar)" newline hexmask.long.byte 0x10 16.--23. 1. "BGND_R,Red component of the default color displayed in the sectors where no layer is active" newline hexmask.long.byte 0x10 8.--15. 1. "BGND_G,Green component of the default color displayed in the sectors where no layer is active" newline hexmask.long.byte 0x10 0.--7. 1. "BGND_B,Blue component of the default color displayed in the sectors where no layer is active" line.long 0x14 "DISP_SIZE,Display Size Register" hexmask.long.word 0x14 16.--27. 1. "DELTA_Y,Sets the display size vertical resolution in pixels" newline hexmask.long.word 0x14 0.--11. 1. "DELTA_X,Sets the display size horizontal resolution in pixels" line.long 0x18 "HSYN_PARA,Horizontal Sync Parameter Register" hexmask.long.word 0x18 22.--30. 1. "BP_H,HSYNC back-porch pulse width (in pixel clock cycles). Pulse width has a minimum value of 1" newline hexmask.long.word 0x18 11.--19. 1. "PW_H,HSYNC active pulse width (in pixel clock cycles). Pulse width has a minimum value of 1" newline hexmask.long.word 0x18 0.--8. 1. "FP_H,HSYNC front-porch pulse width (in pixel clock cycles). Pulse width has a minimum value of 1" line.long 0x1C "VSYN_PARA,Vertical Sync Parameter Register" hexmask.long.word 0x1C 22.--30. 1. "BP_V,VSYNC back-porch pulse width (in horizontal line cycles). Pulse width has a minimum value of 1" newline hexmask.long.word 0x1C 11.--19. 1. "PW_V,VSYNC active pulse width (in horizontal line cycles). Pulse width has a minimum value of 1" newline hexmask.long.word 0x1C 0.--8. 1. "FP_V,VSYNC front-porch pulse width (in horizontal line cycles). Pulse width has a minimum value of 1" line.long 0x20 "INT_STATUS_D0,Interrupt Status Register for domain 0" hexmask.long.byte 0x20 24.--31. 1. "FIFO_EMPTY,Interrupt flag to indicate that which FIFO in the pixel blending underflowed" newline hexmask.long.byte 0x20 16.--23. 1. "DMA_DONE,Interrupt flag to indicate that which PLANE has fetched the last pixel from memory" newline hexmask.long.byte 0x20 8.--15. 1. "DMA_ERR,Interrupt flag to indicate that which PLANE has Read Error on the AXI interface" newline eventfld.long 0x20 2. "VS_BLANK,Interrupt flag to indicate vertical blanking period" "0: Vertical blanking period has not started,1: Vertical blanking period has started" newline eventfld.long 0x20 1. "UNDERRUN,Interrupt flag to indicate the output buffer underrun condition" "0: Output buffer not underrun,1: Output buffer underrun" newline eventfld.long 0x20 0. "VSYNC,Interrupt flag to indicate that the vertical synchronization phase(The beginning of a frame)" "0: VSYNC has not started,1: VSYNC has started" line.long 0x24 "INT_ENABLE_D0,Interrupt Enable Register for domain 0" hexmask.long.byte 0x24 24.--31. 1. "FIFO_EMPTY_EN,Enable Interrupt flag to indicate that which FIFO in the pixel blending underflowed" newline hexmask.long.byte 0x24 16.--23. 1. "DMA_DONE_EN,Enable Interrupt flag to indicate that which PLANE has fetched the last pixel from memory" newline hexmask.long.byte 0x24 8.--15. 1. "DMA_ERR_EN,Enable Interrupt flag to indicate that which PLANE has Read Error on the AXI interface" newline bitfld.long 0x24 2. "VS_BLANK_EN,Enable Interrupt flag to indicate vertical blanking period" "0: Vertical blanking start interrupt disable,1: Vertical blanking start interrupt enable" newline bitfld.long 0x24 1. "UNDERRUN_EN,Enable Interrupt flag to indicate the output buffer underrun condition" "0: Output buffer underrun disable,1: Output buffer underrun enable" newline bitfld.long 0x24 0. "VSYNC_EN,Enable Interrupt flag to indicate that the vertical synchronization phase(The beginning of a frame)" "0: VSYNC interrupt disable,1: VSYNC interrupt enable" group.long 0x30++0x7 line.long 0x0 "INT_STATUS_D1,Interrupt Status Register for domain 1" hexmask.long.byte 0x0 24.--31. 1. "FIFO_EMPTY,Interrupt flag to indicate that which FIFO in the pixel blending underflowed" newline hexmask.long.byte 0x0 16.--23. 1. "DMA_DONE,Interrupt flag to indicate that which PLANE has fetched the last pixel from memory" newline hexmask.long.byte 0x0 8.--15. 1. "DMA_ERR,Interrupt flag to indicate that which PLANE has Read Error on the AXI interface" newline eventfld.long 0x0 2. "VS_BLANK,Interrupt flag to indicate vertical blanking period" "0,1" newline eventfld.long 0x0 1. "UNDERRUN,Interrupt flag to indicate the output buffer underrun condition" "0,1" newline eventfld.long 0x0 0. "VSYNC,Interrupt flag to indicate that the vertical synchronization phase(The beginning of a frame)" "0,1" line.long 0x4 "INT_ENABLE_D1,Interrupt Enable Register for domain 1" hexmask.long.byte 0x4 24.--31. 1. "FIFO_EMPTY_EN,Enable Interrupt flag to indicate that which FIFO in the pixel blending underflowed" newline hexmask.long.byte 0x4 16.--23. 1. "DMA_DONE_EN,Enable Interrupt flag to indicate that which PLANE has fetched the last pixel from memory" newline hexmask.long.byte 0x4 8.--15. 1. "DMA_ERR_EN,Enable Interrupt flag to indicate that which PLANE has Read Error on the AXI interface" newline bitfld.long 0x4 2. "VS_BLANK_EN,Enable Interrupt flag to indicate vertical blanking period" "0,1" newline bitfld.long 0x4 1. "UNDERRUN_EN,Enable Interrupt flag to indicate the output buffer underrun condition" "0,1" newline bitfld.long 0x4 0. "VSYNC_EN,Enable Interrupt flag to indicate that the vertical synchronization phase(The beginning of a frame)" "0,1" group.long 0x40++0x3 line.long 0x0 "PDI_PARA,Parallel Data Interface Parameter Register" bitfld.long 0x0 31. "PDI_EN,Enable PDI input data to LCDIFv2 display" "0: Disable PDI input data,1: Enable PDI input data" newline bitfld.long 0x0 30. "PDI_SEL,PDI selected on LCDIFv2 plane number" "0: PDI selected on LCDIFv2 plane 0,1: PDI selected on LCDIFv2 plane 1" newline hexmask.long.byte 0x0 4.--7. 1. "MODE,The PDI mode for input data format" newline bitfld.long 0x0 3. "INV_PDI_PXCK,Polarity of PDI input Pixel Clock" "0: Samples data on the falling edge,1: Samples data on the rising edge" newline bitfld.long 0x0 2. "INV_PDI_DE,Polarity of PDI input Data Enable" "0: Data enable is active HIGH,1: Data enable is active LOW" newline bitfld.long 0x0 1. "INV_PDI_VS,Polarity of PDI input VSYNC" "0: VSYNC is active HIGH,1: VSYNC is active LOW" newline bitfld.long 0x0 0. "INV_PDI_HS,Polarity of PDI input HSYNC" "0: HSYNC is active HIGH,1: HSYNC is active LOW" group.long 0x200++0x23 line.long 0x0 "CTRLDESCL0_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL0_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL0_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL0_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL0_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL0_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" line.long 0x18 "CSC0_COEF0,Color Space Conversion Coefficient Register 0" bitfld.long 0x18 31. "YCBCR_MODE,This bit changes the behavior when performing U/V converting" "0: Converting YUV to RGB data,1: Converting YCbCr to RGB data" newline bitfld.long 0x18 30. "ENABLE,Enable the CSC unit in the LCDIFv2 plane data path" "0: The CSC is bypassed and the input pixels are RGB..,1: The CSC is enabled and the pixels will be.." newline hexmask.long.word 0x18 18.--28. 1. "C0,Two's compliment Y multiplier coefficient. YUV=0x100 (1.000) YCbCr=0x12A (1.164)" newline hexmask.long.word 0x18 9.--17. 1. "UV_OFFSET,Two's compliment phase offset implicit for CbCr data. Generally used for YCbCr to RGB conversion. YCbCr=0x180 YUV=0x000 (typically -128 or 0x180 to indicate normalized -0.5 to 0.5 range)" newline hexmask.long.word 0x18 0.--8. 1. "Y_OFFSET,Two's compliment amplitude offset implicit in the Y data. For YUV this is typically 0 and for YCbCr this is typically -16 (0x1F0)" line.long 0x1C "CSC0_COEF1,Color Space Conversion Coefficient Register 1" hexmask.long.word 0x1C 16.--26. 1. "C1,Two's compliment Red V/Cr multiplier coefficient. YUV=0x123 (1.140) YCbCr=0x198 (1.596)" newline hexmask.long.word 0x1C 0.--10. 1. "C4,Two's compliment Blue U/Cb multiplier coefficient. YUV=0x208 (2.032) YCbCr=0x204 (2.017)" line.long 0x20 "CSC0_COEF2,Color Space Conversion Coefficient Register 2" hexmask.long.word 0x20 16.--26. 1. "C2,Two's compliment Green V/Cr multiplier coefficient. YUV=0x76B (-0.581) YCbCr=0x730 (-0.813)" newline hexmask.long.word 0x20 0.--10. 1. "C3,Two's compliment Green U/Cb multiplier coefficient. YUV=0x79C (-0.394) YCbCr=0x79C (-0.392)" group.long 0x240++0x23 line.long 0x0 "CTRLDESCL1_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL1_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL1_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL1_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL1_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL1_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" line.long 0x18 "CSC1_COEF0,Color Space Conversion Coefficient Register 0" bitfld.long 0x18 31. "YCBCR_MODE,This bit changes the behavior when performing U/V converting" "0: Converting YUV to RGB data,1: Converting YCbCr to RGB data" newline bitfld.long 0x18 30. "ENABLE,Enable the CSC unit in the LCDIFv2 plane data path" "0: The CSC is bypassed and the input pixels are RGB..,1: The CSC is enabled and the pixels will be.." newline hexmask.long.word 0x18 18.--28. 1. "C0,Two's compliment Y multiplier coefficient. YUV=0x100 (1.000) YCbCr=0x12A (1.164)" newline hexmask.long.word 0x18 9.--17. 1. "UV_OFFSET,Two's compliment phase offset implicit for CbCr data. Generally used for YCbCr to RGB conversion. YCbCr=0x180 YUV=0x000 (typically -128 or 0x180 to indicate normalized -0.5 to 0.5 range)" newline hexmask.long.word 0x18 0.--8. 1. "Y_OFFSET,Two's compliment amplitude offset implicit in the Y data. For YUV this is typically 0 and for YCbCr this is typically -16 (0x1F0)" line.long 0x1C "CSC1_COEF1,Color Space Conversion Coefficient Register 1" hexmask.long.word 0x1C 16.--26. 1. "C1,Two's compliment Red V/Cr multiplier coefficient. YUV=0x123 (1.140) YCbCr=0x198 (1.596)" newline hexmask.long.word 0x1C 0.--10. 1. "C4,Two's compliment Blue U/Cb multiplier coefficient. YUV=0x208 (2.032) YCbCr=0x204 (2.017)" line.long 0x20 "CSC1_COEF2,Color Space Conversion Coefficient Register 2" hexmask.long.word 0x20 16.--26. 1. "C2,Two's compliment Green V/Cr multiplier coefficient. YUV=0x76B (-0.581) YCbCr=0x730 (-0.813)" newline hexmask.long.word 0x20 0.--10. 1. "C3,Two's compliment Green U/Cb multiplier coefficient. YUV=0x79C (-0.394) YCbCr=0x79C (-0.392)" group.long 0x280++0x17 line.long 0x0 "CTRLDESCL2_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL2_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL2_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL2_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL2_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL2_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x2C0++0x17 line.long 0x0 "CTRLDESCL3_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL3_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL3_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL3_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL3_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL3_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x300++0x17 line.long 0x0 "CTRLDESCL4_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL4_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL4_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL4_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL4_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL4_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x340++0x17 line.long 0x0 "CTRLDESCL5_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL5_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL5_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL5_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL5_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL5_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x380++0x17 line.long 0x0 "CTRLDESCL6_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL6_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL6_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL6_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL6_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL6_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x3C0++0x17 line.long 0x0 "CTRLDESCL7_1,Control Descriptor Layer 1 Register" hexmask.long.word 0x0 16.--27. 1. "HEIGHT,Height of the layer in pixels" newline hexmask.long.word 0x0 0.--11. 1. "WIDTH,Width of the layer in pixels" line.long 0x4 "CTRLDESCL7_2,Control Descriptor Layer 2 Register" hexmask.long.word 0x4 16.--27. 1. "POSY,The vertical position of top row of the layer where 0 is the top row of the panel only positive values are below the top row of the panel" newline hexmask.long.word 0x4 0.--11. 1. "POSX,The horizontal position of left-hand column of the layer where 0 is the left-hand column of the panel only positive values are to the right the left-hand column of the panel" line.long 0x8 "CTRLDESCL7_3,Control Descriptor Layer 3 Register" hexmask.long.word 0x8 0.--15. 1. "PITCH,Number of bytes between 2 vertically adjacent pixels in system memory. Byte granularity is supported but SW should align to 64B boundry" line.long 0xC "CTRLDESCL7_4,Control Descriptor Layer 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR,Address of layer data in the memory. The address programmed should be 64-bit aligned" line.long 0x10 "CTRLDESCL7_5,Control Descriptor Layer 5 Register" bitfld.long 0x10 31. "EN,Enable the layer for DMA" "0: OFF,1: ON" newline bitfld.long 0x10 30. "SHADOW_LOAD_EN,Shadow Load Enable" "0,1" newline bitfld.long 0x10 28. "SAFETY_EN,Safety Mode Enable Bit" "0: Safety Mode is disabled,1: Safety Mode is enabled for this layer" newline hexmask.long.byte 0x10 24.--27. 1. "BPP,Layer encoding format (bit per pixel)" newline hexmask.long.byte 0x10 16.--23. 1. "GLOBAL_ALPHA,Global Alpha" newline bitfld.long 0x10 14.--15. "YUV_FORMAT,The YUV422 input format selection" "0: The YVYU422 8bit sequence is U1 Y1 V1 Y2,1: The YVYU422 8bit sequence is V1 Y1 U1 Y2,2: The YVYU422 8bit sequence is Y1 U1 Y2 V1,3: The YVYU422 8bit sequence is Y1 V1 Y2 U1" newline bitfld.long 0x10 9. "PD_COLOR_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff color,1: Inversed mode for Porter Duff color" newline bitfld.long 0x10 8. "PD_ALPHA_MODE,PoterDuff alpha mode" "0: Straight mode for Porter Duff alpha,1: Inversed mode for Porter Duff alpha" newline bitfld.long 0x10 6.--7. "PD_GLOBAL_ALPHA_MODE,PoterDuff global alpha mode" "0: Using global alpha,1: Using local alpha,2: Using scaled alpha,3: Using scaled alpha" newline bitfld.long 0x10 4.--5. "PD_FACTOR_MODE,PoterDuff factor mode" "0: Using 1,1: Using 0,2: Using straight alpha,3: Using inverse alpha" newline bitfld.long 0x10 0.--1. "AB_MODE,Alpha Blending Mode" "0: No alpha Blending (The SAFETY_EN bit need set to..,1: Blend with global ALPHA,2: Blend with embedded ALPHA,3: Blend with PoterDuff enable" line.long 0x14 "CTRLDESCL7_6,Control Descriptor Layer 6 Register" hexmask.long.byte 0x14 16.--23. 1. "BCLR_R,Background R component value" newline hexmask.long.byte 0x14 8.--15. 1. "BCLR_G,Background G component value" newline hexmask.long.byte 0x14 0.--7. 1. "BCLR_B,Background B component value" group.long 0x400++0x3 line.long 0x0 "CLUT_LOAD,LCDIFv2 CLUT load Register" bitfld.long 0x0 4.--6. "SEL_CLUT_NUM,Selected CLUT Number" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0. "CLUT_UPDATE_EN,CLUT Update Enable" "0,1" tree.end sif (cpuis("IMXRT1163-CM4")||cpuis("IMXRT1165-CM4")||cpuis("IMXRT1166-CM4")) tree "LMEM" base ad:0xE0082000 group.long 0x0++0xF line.long 0x0 "PCCCR,PC bus Cache control register" bitfld.long 0x0 31. "GO,Initiate Cache Command" "0: Write: no effect. Read: no cache command active.,1: Write: initiate command indicated by bits 27-24." bitfld.long 0x0 27. "PUSHW1,Push Way 1" "0: No operation,1: When setting the GO bit push all modified lines.." newline bitfld.long 0x0 26. "INVW1,Invalidate Way 1" "0: No operation,1: When setting the GO bit invalidate all lines in.." bitfld.long 0x0 25. "PUSHW0,Push Way 0" "0: No operation,1: When setting the GO bit push all modified lines.." newline bitfld.long 0x0 24. "INVW0,Invalidate Way 0" "0: No operation,1: When setting the GO bit invalidate all lines in.." bitfld.long 0x0 3. "PCCR3,Forces no allocation on cache misses" "0: Allocation on cache misses,1: Forces no allocation on cache misses (must also.." newline bitfld.long 0x0 2. "PCCR2,Forces all cacheable spaces to write through" "0: Does NOT force all cacheable spaces to write..,1: Forces all cacheable spaces to write through" bitfld.long 0x0 1. "ENWRBUF,Enable Write Buffer" "0: Write buffer disabled,1: Write buffer enabled" newline bitfld.long 0x0 0. "ENCACHE,Cache enable" "0: Cache disabled,1: Cache enabled" line.long 0x4 "PCCLCR,PC bus Cache line control register" bitfld.long 0x4 27. "LACC,Line access type" "0: Read,1: Write" bitfld.long 0x4 26. "LADSEL,Line Address Select" "0: Cache address,1: Physical address" newline bitfld.long 0x4 24.--25. "LCMD,Line Command" "0: Search and read or write,1: Invalidate,2: Push,3: Clear" bitfld.long 0x4 22. "LCWAY,Line Command Way" "0,1" newline bitfld.long 0x4 21. "LCIMB,Line Command Initial Modified Bit" "0,1" bitfld.long 0x4 20. "LCIVB,Line Command Initial Valid Bit" "0,1" newline bitfld.long 0x4 16. "TDSEL,Tag/Data Select" "0: Data,1: Tag" bitfld.long 0x4 14. "WSEL,Way select" "0: Way 0,1: Way 1" newline hexmask.long.word 0x4 2.--13. 1. "CACHEADDR,Cache address" bitfld.long 0x4 0. "LGO,Initiate Cache Line Command" "0: Write: no effect. Read: no line command active.,1: Write: initiate line command indicated by bits.." line.long 0x8 "PCCSAR,PC bus Cache search address register" hexmask.long 0x8 1.--31. 1. "PHYADDR,Physical Address" bitfld.long 0x8 0. "LGO,Initiate Cache Line Command" "0: Write: no effect. Read: no line command active.,1: Write: initiate line command indicated by bits.." line.long 0xC "PCCCVR,PC bus Cache read/write value register" hexmask.long 0xC 0.--31. 1. "DATA,Cache read/write Data" group.long 0x800++0xF line.long 0x0 "PSCCR,PS bus Cache control register" bitfld.long 0x0 31. "GO,Initiate Cache Command" "0: Write: no effect. Read: no cache command active.,1: Write: initiate command indicated by bits 27-24." bitfld.long 0x0 27. "PUSHW1,Push Way 1" "0: No operation,1: When setting the GO bit push all modified lines.." newline bitfld.long 0x0 26. "INVW1,Invalidate Way 1" "0: No operation,1: When setting the GO bit invalidate all lines in.." bitfld.long 0x0 25. "PUSHW0,Push Way 0" "0: No operation,1: When setting the GO bit push all modified lines.." newline bitfld.long 0x0 24. "INVW0,Invalidate Way 0" "0: No operation,1: When setting the GO bit invalidate all lines in.." bitfld.long 0x0 3. "PSCR3,Forces no allocation on cache misses" "0: Allocation on cache misses,1: Forces no allocation on cache misses (must also.." newline bitfld.long 0x0 2. "PSCR2,Forces all cacheable spaces to write through" "0: Does NOT force all cacheable spaces to write..,1: Forces all cacheable spaces to write through" bitfld.long 0x0 1. "ENWRBUF,Enable Write Buffer" "0: Write buffer disabled,1: Write buffer enabled" newline bitfld.long 0x0 0. "ENCACHE,Cache enable" "0: Cache disabled,1: Cache enabled" line.long 0x4 "PSCLCR,PS bus Cache line control register" bitfld.long 0x4 27. "LACC,Line access type" "0: Read,1: Write" bitfld.long 0x4 26. "LADSEL,Line Address Select" "0: Cache address,1: Physical address" newline bitfld.long 0x4 24.--25. "LCMD,Line Command" "0: Search and read or write,1: Invalidate,2: Push,3: Clear" bitfld.long 0x4 22. "LCWAY,Line Command Way" "0,1" newline bitfld.long 0x4 21. "LCIMB,Line Command Initial Modified Bit" "0,1" bitfld.long 0x4 20. "LCIVB,Line Command Initial Valid Bit" "0,1" newline bitfld.long 0x4 16. "TDSEL,Tag/Data Select" "0: Data,1: Tag" bitfld.long 0x4 14. "WSEL,Way select" "0: Way 0,1: Way 1" newline hexmask.long.word 0x4 2.--13. 1. "CACHEADDR,Cache address" bitfld.long 0x4 0. "LGO,Initiate Cache Line Command" "0: Write: no effect. Read: no line command active.,1: Write: initiate line command indicated by bits.." line.long 0x8 "PSCSAR,PS bus Cache search address register" hexmask.long 0x8 1.--31. 1. "PHYADDR,Physical Address" bitfld.long 0x8 0. "LGO,Initiate Cache Line Command" "0: Write: no effect. Read: no line command active.,1: Write: initiate line command indicated by bits.." line.long 0xC "PSCCVR,PS bus Cache read/write value register" hexmask.long 0xC 0.--31. 1. "DATA,Cache read/write Data" tree.end endif tree "LPI2C" base ad:0x0 tree "LPI2C1" base ad:0x40104000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree "LPI2C2" base ad:0x40108000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree "LPI2C3" base ad:0x4010C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree "LPI2C4" base ad:0x40110000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree "LPI2C5" base ad:0x40C34000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree "LPI2C6" base ad:0x40C38000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 8.--11. 1. "MRXFIFO,Master Receive FIFO Size" hexmask.long.byte 0x4 0.--3. 1. "MTXFIFO,Master Transmit FIFO Size" group.long 0x10++0x1F line.long 0x0 "MCR,Master Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive FIFO is reset" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit FIFO is reset" newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: Master is disabled in debug mode,1: Master is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze mode enable" "0: Master is enabled in Doze mode,1: Master is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Master logic is not reset,1: Master logic is reset" bitfld.long 0x0 0. "MEN,Master Enable" "0: Master logic is disabled,1: Master logic is enabled" line.long 0x4 "MSR,Master Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "MBF,Master Busy Flag" "0: I2C Master is idle,1: I2C Master is busy" newline eventfld.long 0x4 14. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" eventfld.long 0x4 13. "PLTF,Pin Low Timeout Flag" "0: Pin low timeout has not occurred or is disabled,1: Pin low timeout has occurred" newline eventfld.long 0x4 12. "FEF,FIFO Error Flag" "0: No error,1: Master sending or receiving data without a START.." eventfld.long 0x4 11. "ALF,Arbitration Lost Flag" "0: Master has not lost arbitration,1: Master has lost arbitration" newline eventfld.long 0x4 10. "NDF,NACK Detect Flag" "0: Unexpected NACK was not detected,1: Unexpected NACK was detected" eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Master has not generated a STOP condition,1: Master has generated a STOP condition" newline eventfld.long 0x4 8. "EPF,End Packet Flag" "0: Master has not generated a STOP or Repeated..,1: Master has generated a STOP or Repeated START.." rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data is not requested,1: Transmit data is requested" line.long 0x8 "MIER,Master Interrupt Enable" bitfld.long 0x8 14. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 13. "PLTIE,Pin Low Timeout Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "FEIE,FIFO Error Interrupt Enable" "0: Enabled,1: Disabled" bitfld.long 0x8 11. "ALIE,Arbitration Lost Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "NDIE,NACK Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "EPIE,End Packet Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "MDER,Master DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "MCFGR0,Master Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO,1: Received data is discarded unless the the Data.." bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" newline bitfld.long 0x10 2. "HRSEL,Host Request Select" "0: Host request input is pin HREQ,1: Host request input is input trigger" bitfld.long 0x10 1. "HRPOL,Host Request Polarity" "0: Active low,1: Active high" newline bitfld.long 0x10 0. "HREN,Host Request Enable" "0: Host request input is disabled,1: Host request input is enabled" line.long 0x14 "MCFGR1,Master Configuration 1" bitfld.long 0x14 24.--26. "PINCFG,Pin Configuration" "0: 2-pin open drain mode,1: 2-pin output only mode (ultra-fast mode),2: 2-pin push-pull mode,3: 4-pin push-pull mode,4: 2-pin open drain mode with separate LPI2C slave,5: 2-pin output only mode (ultra-fast mode) with..,6: 2-pin push-pull mode with separate LPI2C slave,7: 4-pin push-pull mode (inverted outputs)" bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled (1st data word equals..,3: Match is enabled (any data word equals..,4: Match is enabled (1st data word equals..,5: Match is enabled (any data word equals..,6: Match is enabled (1st data word AND MDMR[MATCH1]..,7: Match is enabled (any data word AND MDMR[MATCH1].." newline bitfld.long 0x14 10. "TIMECFG,Timeout Configuration" "0: MSR[PLTF] sets if SCL is low for longer than the..,1: MSR[PLTF] sets if either SCL or SDA is low for.." bitfld.long 0x14 9. "IGNACK,IGNACK" "0: LPI2C Master receives ACK and NACK normally,1: LPI2C Master treats a received NACK as if it.." newline bitfld.long 0x14 8. "AUTOSTOP,Automatic STOP Generation" "0: No effect,1: STOP condition is automatically generated.." bitfld.long 0x14 0.--2. "PRESCALE,Prescaler" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" line.long 0x18 "MCFGR2,Master Configuration 2" hexmask.long.byte 0x18 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x18 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.word 0x18 0.--11. 1. "BUSIDLE,Bus Idle Timeout" line.long 0x1C "MCFGR3,Master Configuration 3" hexmask.long.word 0x1C 8.--19. 1. "PINLOW,Pin Low Timeout" group.long 0x40++0x3 line.long 0x0 "MDMR,Master Data Match" hexmask.long.byte 0x0 16.--23. 1. "MATCH1,Match 1 Value" hexmask.long.byte 0x0 0.--7. 1. "MATCH0,Match 0 Value" group.long 0x48++0x3 line.long 0x0 "MCCR0,Master Clock Configuration 0" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x50++0x3 line.long 0x0 "MCCR1,Master Clock Configuration 1" hexmask.long.byte 0x0 24.--29. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x0 16.--21. 1. "SETHOLD,Setup Hold Delay" newline hexmask.long.byte 0x0 8.--13. 1. "CLKHI,Clock High Period" hexmask.long.byte 0x0 0.--5. 1. "CLKLO,Clock Low Period" group.long 0x58++0x3 line.long 0x0 "MFCR,Master FIFO Control" bitfld.long 0x0 16.--17. "RXWATER,Receive FIFO Watermark" "0,1,2,3" bitfld.long 0x0 0.--1. "TXWATER,Transmit FIFO Watermark" "0,1,2,3" rgroup.long 0x5C++0x3 line.long 0x0 "MFSR,Master FIFO Status" bitfld.long 0x0 16.--18. "RXCOUNT,Receive FIFO Count" "0,1,2,3,4,5,6,7" bitfld.long 0x0 0.--2. "TXCOUNT,Transmit FIFO Count" "0,1,2,3,4,5,6,7" wgroup.long 0x60++0x3 line.long 0x0 "MTDR,Master Transmit Data" bitfld.long 0x0 8.--10. "CMD,Command Data" "0: Transmit DATA[7:0],1: Receive (DATA[7:0] + 1) bytes,2: Generate STOP condition,3: Receive and discard (DATA[7:0] + 1) bytes,4: Generate (repeated) START and transmit address..,5: Generate (repeated) START and transmit address..,6: Generate (repeated) START and transmit address..,7: Generate (repeated) START and transmit address.." hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x70++0x3 line.long 0x0 "MRDR,Master Receive Data" bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: Receive FIFO is not empty,1: Receive FIFO is empty" hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" group.long 0x110++0xF line.long 0x0 "SCR,Slave Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Receive Data Register is now empty" bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Transmit Data Register is now empty" newline bitfld.long 0x0 5. "FILTDZ,Filter Doze Enable" "0: Filter remains enabled in Doze mode,1: Filter is disabled in Doze mode" bitfld.long 0x0 4. "FILTEN,Filter Enable" "0: Disable digital filter and output delay counter..,1: Enable digital filter and output delay counter.." newline bitfld.long 0x0 1. "RST,Software Reset" "0: Slave mode logic is not reset,1: Slave mode logic is reset" bitfld.long 0x0 0. "SEN,Slave Enable" "0: I2C Slave mode is disabled,1: I2C Slave mode is enabled" line.long 0x4 "SSR,Slave Status" rbitfld.long 0x4 25. "BBF,Bus Busy Flag" "0: I2C Bus is idle,1: I2C Bus is busy" rbitfld.long 0x4 24. "SBF,Slave Busy Flag" "0: I2C Slave is idle,1: I2C Slave is busy" newline rbitfld.long 0x4 15. "SARF,SMBus Alert Response Flag" "0: SMBus Alert Response is disabled or not detected,1: SMBus Alert Response is enabled and detected" rbitfld.long 0x4 14. "GCF,General Call Flag" "0: Slave has not detected the General Call Address..,1: Slave has detected the General Call Address" newline rbitfld.long 0x4 13. "AM1F,Address Match 1 Flag" "0: Have not received an ADDR1 or ADDR0/ADDR1 range..,1: Have received an ADDR1 or ADDR0/ADDR1 range.." rbitfld.long 0x4 12. "AM0F,Address Match 0 Flag" "0: Have not received an ADDR0 matching address,1: Have received an ADDR0 matching address" newline eventfld.long 0x4 11. "FEF,FIFO Error Flag" "0: FIFO underflow or overflow was not detected,1: FIFO underflow or overflow was detected" eventfld.long 0x4 10. "BEF,Bit Error Flag" "0: Slave has not detected a bit error,1: Slave has detected a bit error" newline eventfld.long 0x4 9. "SDF,STOP Detect Flag" "0: Slave has not detected a STOP condition,1: Slave has detected a STOP condition" eventfld.long 0x4 8. "RSF,Repeated Start Flag" "0: Slave has not detected a Repeated START condition,1: Slave has detected a Repeated START condition" newline rbitfld.long 0x4 3. "TAF,Transmit ACK Flag" "0: Transmit ACK/NACK is not required,1: Transmit ACK/NACK is required" rbitfld.long 0x4 2. "AVF,Address Valid Flag" "0: Address Status Register is not valid,1: Address Status Register is valid" newline rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive data is not ready,1: Receive data is ready" rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "SIER,Slave Interrupt Enable" bitfld.long 0x8 15. "SARIE,SMBus Alert Response Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 14. "GCIE,General Call Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "AM1IE,Address Match 1 Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "AM0IE,Address Match 0 Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "FEIE,FIFO Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "BEIE,Bit Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "SDIE,STOP Detect Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "RSIE,Repeated Start Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "TAIE,Transmit ACK Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 2. "AVIE,Address Valid Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "SDER,Slave DMA Enable" bitfld.long 0xC 2. "AVDE,Address Valid DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" newline bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" group.long 0x124++0x7 line.long 0x0 "SCFGR1,Slave Configuration 1" bitfld.long 0x0 16.--18. "ADDRCFG,Address Configuration" "0: Address match 0 (7-bit),1: Address match 0 (10-bit),2: Address match 0 (7-bit) or Address match 1 (7-bit),3: Address match 0 (10-bit) or Address match 1..,4: Address match 0 (7-bit) or Address match 1..,5: Address match 0 (10-bit) or Address match 1..,6: From Address match 0 (7-bit) to Address match 1..,7: From Address match 0 (10-bit) to Address match 1.." bitfld.long 0x0 13. "HSMEN,High Speed Mode Enable" "0: Disables detection of HS-mode master code,1: Enables detection of HS-mode master code" newline bitfld.long 0x0 12. "IGNACK,Ignore NACK" "0: Slave ends transfer when NACK is detected,1: Slave does not end transfer when NACK detected" bitfld.long 0x0 11. "RXCFG,Receive Data Configuration" "0: Reading the Receive Data register returns..,1: Reading the Receive Data register when the.." newline bitfld.long 0x0 10. "TXCFG,Transmit Flag Configuration" "0: Transmit Data Flag only asserts during a..,1: Transmit Data Flag asserts whenever the Transmit.." bitfld.long 0x0 9. "SAEN,SMBus Alert Enable" "0: Disables match on SMBus Alert,1: Enables match on SMBus Alert" newline bitfld.long 0x0 8. "GCEN,General Call Enable" "0: General Call address is disabled,1: General Call address is enabled" bitfld.long 0x0 3. "ACKSTALL,ACK SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 2. "TXDSTALL,TX Data SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" bitfld.long 0x0 1. "RXSTALL,RX SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" newline bitfld.long 0x0 0. "ADRSTALL,Address SCL Stall" "0: Clock stretching is disabled,1: Clock stretching is enabled" line.long 0x4 "SCFGR2,Slave Configuration 2" hexmask.long.byte 0x4 24.--27. 1. "FILTSDA,Glitch Filter SDA" hexmask.long.byte 0x4 16.--19. 1. "FILTSCL,Glitch Filter SCL" newline hexmask.long.byte 0x4 8.--13. 1. "DATAVD,Data Valid Delay" hexmask.long.byte 0x4 0.--3. 1. "CLKHOLD,Clock Hold Time" group.long 0x140++0x3 line.long 0x0 "SAMR,Slave Address Match" hexmask.long.word 0x0 17.--26. 1. "ADDR1,Address 1 Value" hexmask.long.word 0x0 1.--10. 1. "ADDR0,Address 0 Value" rgroup.long 0x150++0x3 line.long 0x0 "SASR,Slave Address Status" bitfld.long 0x0 14. "ANV,Address Not Valid" "0: Received Address (RADDR) is valid,1: Received Address (RADDR) is not valid" hexmask.long.word 0x0 0.--10. 1. "RADDR,Received Address" group.long 0x154++0x3 line.long 0x0 "STAR,Slave Transmit ACK" bitfld.long 0x0 0. "TXNACK,Transmit NACK" "0: Write a Transmit ACK for each received word,1: Write a Transmit NACK for each received word" wgroup.long 0x160++0x3 line.long 0x0 "STDR,Slave Transmit Data" hexmask.long.byte 0x0 0.--7. 1. "DATA,Transmit Data" rgroup.long 0x170++0x3 line.long 0x0 "SRDR,Slave Receive Data" bitfld.long 0x0 15. "SOF,Start Of Frame" "0: Indicates this is not the first data word since..,1: Indicates this is the first data word since a.." bitfld.long 0x0 14. "RXEMPTY,RX Empty" "0: The Receive Data Register is not empty,1: The Receive Data Register is empty" newline hexmask.long.byte 0x0 0.--7. 1. "DATA,Receive Data" tree.end tree.end tree "LPSPI" base ad:0x0 tree "LPSPI1" base ad:0x40114000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree "LPSPI2" base ad:0x40118000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree "LPSPI3" base ad:0x4011C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree "LPSPI4" base ad:0x40120000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree "LPSPI5" base ad:0x40C2C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree "LPSPI6" base ad:0x40C30000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Module Identification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--23. 1. "PCSNUM,PCS Number" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" newline hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x10++0x17 line.long 0x0 "CR,Control" bitfld.long 0x0 9. "RRF,Reset Receive FIFO" "0: No effect,1: Reset the Receive FIFO. The register bit always.." bitfld.long 0x0 8. "RTF,Reset Transmit FIFO" "0: No effect,1: Reset the Transmit FIFO. The register bit always.." newline bitfld.long 0x0 3. "DBGEN,Debug Enable" "0: LPSPI module is disabled in debug mode,1: LPSPI module is enabled in debug mode" bitfld.long 0x0 2. "DOZEN,Doze Mode Enable" "0: LPSPI module is enabled in Doze mode,1: LPSPI module is disabled in Doze mode" newline bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset,1: Module is reset" bitfld.long 0x0 0. "MEN,Module Enable" "0: Module is disabled,1: Module is enabled" line.long 0x4 "SR,Status" rbitfld.long 0x4 24. "MBF,Module Busy Flag" "0: LPSPI is idle,1: LPSPI is busy" eventfld.long 0x4 13. "DMF,Data Match Flag" "0: Have not received matching data,1: Have received matching data" newline eventfld.long 0x4 12. "REF,Receive Error Flag" "0: Receive FIFO has not overflowed,1: Receive FIFO has overflowed" eventfld.long 0x4 11. "TEF,Transmit Error Flag" "0: Transmit FIFO underrun has not occurred,1: Transmit FIFO underrun has occurred" newline eventfld.long 0x4 10. "TCF,Transfer Complete Flag" "0: All transfers have not completed,1: All transfers have completed" eventfld.long 0x4 9. "FCF,Frame Complete Flag" "0: Frame transfer has not completed,1: Frame transfer has completed" newline eventfld.long 0x4 8. "WCF,Word Complete Flag" "0: Transfer of a received word has not yet completed,1: Transfer of a received word has completed" rbitfld.long 0x4 1. "RDF,Receive Data Flag" "0: Receive Data is not ready,1: Receive data is ready" newline rbitfld.long 0x4 0. "TDF,Transmit Data Flag" "0: Transmit data not requested,1: Transmit data is requested" line.long 0x8 "IER,Interrupt Enable" bitfld.long 0x8 13. "DMIE,Data Match Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 12. "REIE,Receive Error Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "TEIE,Transmit Error Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 10. "TCIE,Transfer Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "FCIE,Frame Complete Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 8. "WCIE,Word Complete Interrupt Enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "RDIE,Receive Data Interrupt Enable" "0: Disabled,1: Enabled" bitfld.long 0x8 0. "TDIE,Transmit Data Interrupt Enable" "0: Disabled,1: Enabled" line.long 0xC "DER,DMA Enable" bitfld.long 0xC 1. "RDDE,Receive Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" bitfld.long 0xC 0. "TDDE,Transmit Data DMA Enable" "0: DMA request is disabled,1: DMA request is enabled" line.long 0x10 "CFGR0,Configuration 0" bitfld.long 0x10 9. "RDMO,Receive Data Match Only" "0: Received data is stored in the receive FIFO as..,1: Received data is discarded unless the SR[DMF] = 1" bitfld.long 0x10 8. "CIRFIFO,Circular FIFO Enable" "0: Circular FIFO is disabled,1: Circular FIFO is enabled" line.long 0x14 "CFGR1,Configuration 1" bitfld.long 0x14 27. "PCSCFG,Peripheral Chip Select Configuration" "0: PCS[3:2] are configured for chip select function,1: PCS[3:2] are configured for half-duplex 4-bit.." bitfld.long 0x14 26. "OUTCFG,Output Configuration" "0: Output data retains last value when chip select..,1: Output data is tristated when chip select is.." newline bitfld.long 0x14 24.--25. "PINCFG,Pin Configuration" "0: SIN is used for input data and SOUT is used for..,1: SIN is used for both input and output data only..,2: SOUT is used for both input and output data only..,3: SOUT is used for input data and SIN is used for.." bitfld.long 0x14 16.--18. "MATCFG,Match Configuration" "0: Match is disabled,?,2: Match is enabled is 1st data word is MATCH0 or..,3: Match is enabled on any data word equal MATCH0..,4: Match is enabled on data match sequence,5: Match is enabled on data match sequence,6: Match is enabled,7: Match is enabled" newline hexmask.long.byte 0x14 8.--11. 1. "PCSPOL,Peripheral Chip Select Polarity" bitfld.long 0x14 3. "NOSTALL,No Stall" "0: Transfers stall when the transmit FIFO is empty,1: Transfers do not stall allowing transmit FIFO.." newline bitfld.long 0x14 2. "AUTOPCS,Automatic PCS" "0: Automatic PCS generation is disabled,1: Automatic PCS generation is enabled" bitfld.long 0x14 1. "SAMPLE,Sample Point" "0: Input data is sampled on SCK edge,1: Input data is sampled on delayed SCK edge" newline bitfld.long 0x14 0. "MASTER,Master Mode" "0: Slave mode,1: Master mode" group.long 0x30++0x7 line.long 0x0 "DMR0,Data Match 0" hexmask.long 0x0 0.--31. 1. "MATCH0,Match 0 Value" line.long 0x4 "DMR1,Data Match 1" hexmask.long 0x4 0.--31. 1. "MATCH1,Match 1 Value" group.long 0x40++0x3 line.long 0x0 "CCR,Clock Configuration" hexmask.long.byte 0x0 24.--31. 1. "SCKPCS,SCK-to-PCS Delay" hexmask.long.byte 0x0 16.--23. 1. "PCSSCK,PCS-to-SCK Delay" newline hexmask.long.byte 0x0 8.--15. 1. "DBT,Delay Between Transfers" hexmask.long.byte 0x0 0.--7. 1. "SCKDIV,SCK Divider" group.long 0x58++0x3 line.long 0x0 "FCR,FIFO Control" hexmask.long.byte 0x0 16.--19. 1. "RXWATER,Receive FIFO Watermark" hexmask.long.byte 0x0 0.--3. 1. "TXWATER,Transmit FIFO Watermark" rgroup.long 0x5C++0x3 line.long 0x0 "FSR,FIFO Status" hexmask.long.byte 0x0 16.--20. 1. "RXCOUNT,Receive FIFO Count" hexmask.long.byte 0x0 0.--4. 1. "TXCOUNT,Transmit FIFO Count" group.long 0x60++0x3 line.long 0x0 "TCR,Transmit Command" bitfld.long 0x0 31. "CPOL,Clock Polarity" "0: The inactive state value of SCK is low,1: The inactive state value of SCK is high" bitfld.long 0x0 30. "CPHA,Clock Phase" "0: Captured,1: Changed" newline bitfld.long 0x0 27.--29. "PRESCALE,Prescaler Value" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,6: Divide by 64,7: Divide by 128" bitfld.long 0x0 24.--25. "PCS,Peripheral Chip Select" "0: Transfer using PCS[0],1: Transfer using PCS[1],2: Transfer using PCS[2],3: Transfer using PCS[3]" newline bitfld.long 0x0 23. "LSBF,LSB First" "0: Data is transferred MSB first,1: Data is transferred LSB first" bitfld.long 0x0 22. "BYSW,Byte Swap" "0: Byte swap is disabled,1: Byte swap is enabled" newline bitfld.long 0x0 21. "CONT,Continuous Transfer" "0: Continuous transfer is disabled,1: Continuous transfer is enabled" bitfld.long 0x0 20. "CONTC,Continuing Command" "0: Command word for start of new transfer,1: Command word for continuing transfer" newline bitfld.long 0x0 19. "RXMSK,Receive Data Mask" "0: Normal transfer,1: Receive data is masked" bitfld.long 0x0 18. "TXMSK,Transmit Data Mask" "0: Normal transfer,1: Mask transmit data" newline bitfld.long 0x0 16.--17. "WIDTH,Transfer Width" "0: 1 bit transfer,1: 2 bit transfer,2: 4 bit transfer,?" hexmask.long.word 0x0 0.--11. 1. "FRAMESZ,Frame Size" wgroup.long 0x64++0x3 line.long 0x0 "TDR,Transmit Data" hexmask.long 0x0 0.--31. 1. "DATA,Transmit Data" rgroup.long 0x70++0x7 line.long 0x0 "RSR,Receive Status" bitfld.long 0x0 1. "RXEMPTY,RX FIFO Empty" "0: RX FIFO is not empty,1: RX FIFO is empty" bitfld.long 0x0 0. "SOF,Start Of Frame" "0: Subsequent data word received after PCS assertion,1: First data word received after PCS assertion" line.long 0x4 "RDR,Receive Data" hexmask.long 0x4 0.--31. 1. "DATA,Receive Data" tree.end tree.end tree "LPUART" base ad:0x0 tree "LPUART1" base ad:0x4007C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART2" base ad:0x40080000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART3" base ad:0x40084000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART4" base ad:0x40088000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART5" base ad:0x4008C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART6" base ad:0x40090000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART7" base ad:0x40094000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART8" base ad:0x40098000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART9" base ad:0x4009C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART10" base ad:0x400A0000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART11" base ad:0x40C24000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree "LPUART12" base ad:0x40C28000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Identification Number" line.long 0x4 "PARAM,Parameter Register" hexmask.long.byte 0x4 8.--15. 1. "RXFIFO,Receive FIFO Size" hexmask.long.byte 0x4 0.--7. 1. "TXFIFO,Transmit FIFO Size" group.long 0x8++0x27 line.long 0x0 "GLOBAL,LPUART Global Register" bitfld.long 0x0 1. "RST,Software Reset" "0: Module is not reset.,1: Module is reset." line.long 0x4 "PINCFG,LPUART Pin Configuration Register" bitfld.long 0x4 0.--1. "TRGSEL,Trigger Select" "0: Input trigger is disabled.,1: Input trigger is used instead of RXD pin input.,2: Input trigger is used instead of CTS_B pin input.,3: Input trigger is used to modulate the TXD pin.." line.long 0x8 "BAUD,LPUART Baud Rate Register" bitfld.long 0x8 31. "MAEN1,Match Address Mode Enable 1" "0: Normal operation.,1: Enables automatic address matching or data.." bitfld.long 0x8 30. "MAEN2,Match Address Mode Enable 2" "0: Normal operation.,1: Enables automatic address matching or data.." newline bitfld.long 0x8 29. "M10,10-bit Mode select" "0: Receiver and transmitter use 7-bit to 9-bit data..,1: Receiver and transmitter use 10-bit data.." hexmask.long.byte 0x8 24.--28. 1. "OSR,Oversampling Ratio" newline bitfld.long 0x8 23. "TDMAE,Transmitter DMA Enable" "0: DMA request disabled.,1: DMA request enabled." bitfld.long 0x8 21. "RDMAE,Receiver Full DMA Enable" "0: DMA request disabled.,1: DMA request enabled." newline bitfld.long 0x8 18.--19. "MATCFG,Match Configuration" "0: Address Match Wakeup,1: Idle Match Wakeup,2: Match On and Match Off,3: Enables RWU on Data Match and Match On/Off for.." bitfld.long 0x8 17. "BOTHEDGE,Both Edge Sampling" "0: Receiver samples input data using the rising..,1: Receiver samples input data using the rising and.." newline bitfld.long 0x8 16. "RESYNCDIS,Resynchronization Disable" "0: Resynchronization during received data word is..,1: Resynchronization during received data word is.." bitfld.long 0x8 15. "LBKDIE,LIN Break Detect Interrupt Enable" "0: Hardware interrupts from STAT[LBKDIF] flag are..,1: Hardware interrupt is requested when.." newline bitfld.long 0x8 14. "RXEDGIE,RX Input Active Edge Interrupt Enable" "0: Hardware interrupts from STAT[RXEDGIF] are..,1: Hardware interrupt is requested when.." bitfld.long 0x8 13. "SBNS,Stop Bit Number Select" "0: One stop bit.,1: Two stop bits." newline hexmask.long.word 0x8 0.--12. 1. "SBR,Baud Rate Modulo Divisor." line.long 0xC "STAT,LPUART Status Register" eventfld.long 0xC 31. "LBKDIF,LIN Break Detect Interrupt Flag" "0: No LIN break character has been detected.,1: LIN break character has been detected." eventfld.long 0xC 30. "RXEDGIF,RXD Pin Active Edge Interrupt Flag" "0: No active edge on the receive pin has occurred.,1: An active edge on the receive pin has occurred." newline bitfld.long 0xC 29. "MSBF,MSB First" "0: LSB (bit0) is the first bit that is transmitted..,1: MSB (identified as bit9 bit8 bit7 or bit6) is.." bitfld.long 0xC 28. "RXINV,Receive Data Inversion" "0: Receive data not inverted.,1: Receive data inverted." newline bitfld.long 0xC 27. "RWUID,Receive Wake Up Idle Detect" "0: During receive standby state (RWU = 1) the IDLE..,1: During receive standby state (RWU = 1) the IDLE.." bitfld.long 0xC 26. "BRK13,Break Character Generation Length" "0: Break character is transmitted with length of 9..,1: Break character is transmitted with length of 12.." newline bitfld.long 0xC 25. "LBKDE,LIN Break Detection Enable" "0: LIN break detect is disabled normal break..,1: LIN break detect is enabled. LIN break character.." rbitfld.long 0xC 24. "RAF,Receiver Active Flag" "0: LPUART receiver idle waiting for a start bit.,1: LPUART receiver active (RXD input not idle)." newline rbitfld.long 0xC 23. "TDRE,Transmit Data Register Empty Flag" "0: Transmit FIFO level is greater than watermark.,1: Transmit FIFO level is equal or less than.." rbitfld.long 0xC 22. "TC,Transmission Complete Flag" "0: Transmitter active (sending data a preamble or a..,1: Transmitter idle (transmission activity complete)." newline rbitfld.long 0xC 21. "RDRF,Receive Data Register Full Flag" "0: Receive FIFO level is less than watermark.,1: Receive FIFO level is equal or greater than.." eventfld.long 0xC 20. "IDLE,Idle Line Flag" "0: No idle line detected.,1: Idle line is detected." newline eventfld.long 0xC 19. "OR,Receiver Overrun Flag" "0: No overrun.,1: Receive overrun (new LPUART data lost)." eventfld.long 0xC 18. "NF,Noise Flag" "0: No noise detected.,1: Noise detected in the received character in the.." newline eventfld.long 0xC 17. "FE,Framing Error Flag" "0: No framing error detected. This does not..,1: Framing error." eventfld.long 0xC 16. "PF,Parity Error Flag" "0: No parity error.,1: Parity error." newline eventfld.long 0xC 15. "MA1F,Match 1 Flag" "0: Received data is not equal to MA1,1: Received data is equal to MA1" eventfld.long 0xC 14. "MA2F,Match 2 Flag" "0: Received data is not equal to MA2,1: Received data is equal to MA2" line.long 0x10 "CTRL,LPUART Control Register" bitfld.long 0x10 31. "R8T9,Receive Bit 8 / Transmit Bit 9" "0,1" bitfld.long 0x10 30. "R9T8,Receive Bit 9 / Transmit Bit 8" "0,1" newline bitfld.long 0x10 29. "TXDIR,TXD Pin Direction in Single-Wire Mode" "0: TXD pin is an input in single-wire mode.,1: TXD pin is an output in single-wire mode." bitfld.long 0x10 28. "TXINV,Transmit Data Inversion" "0: Transmit data not inverted.,1: Transmit data inverted." newline bitfld.long 0x10 27. "ORIE,Overrun Interrupt Enable" "0: OR interrupts disabled; use polling.,1: Hardware interrupt is requested when OR is set." bitfld.long 0x10 26. "NEIE,Noise Error Interrupt Enable" "0: NF interrupts disabled; use polling.,1: Hardware interrupt is requested when NF is set." newline bitfld.long 0x10 25. "FEIE,Framing Error Interrupt Enable" "0: FE interrupts disabled; use polling.,1: Hardware interrupt is requested when FE is set." bitfld.long 0x10 24. "PEIE,Parity Error Interrupt Enable" "0: PF interrupts disabled; use polling).,1: Hardware interrupt is requested when PF is set." newline bitfld.long 0x10 23. "TIE,Transmit Interrupt Enable" "0: Hardware interrupts from TDRE disabled.,1: Hardware interrupt is requested when TDRE flag.." bitfld.long 0x10 22. "TCIE,Transmission Complete Interrupt Enable for" "0: Hardware interrupts from TC disabled.,1: Hardware interrupt is requested when TC flag is 1." newline bitfld.long 0x10 21. "RIE,Receiver Interrupt Enable" "0: Hardware interrupts from RDRF disabled.,1: Hardware interrupt is requested when RDRF flag.." bitfld.long 0x10 20. "ILIE,Idle Line Interrupt Enable" "0: Hardware interrupts from IDLE disabled; use..,1: Hardware interrupt is requested when IDLE flag.." newline bitfld.long 0x10 19. "TE,Transmitter Enable" "0: Transmitter disabled.,1: Transmitter enabled." bitfld.long 0x10 18. "RE,Receiver Enable" "0: Receiver disabled.,1: Receiver enabled." newline bitfld.long 0x10 17. "RWU,Receiver Wakeup Control" "0: Normal receiver operation.,1: LPUART receiver in standby waiting for wakeup.." bitfld.long 0x10 16. "SBK,Send Break" "0: Normal transmitter operation.,1: Queue break character(s) to be sent." newline bitfld.long 0x10 15. "MA1IE,Match 1 Interrupt Enable" "0: MA1F interrupt disabled,1: MA1F interrupt enabled" bitfld.long 0x10 14. "MA2IE,Match 2 Interrupt Enable" "0: MA2F interrupt disabled,1: MA2F interrupt enabled" newline bitfld.long 0x10 11. "M7,7-Bit Mode Select" "0: Receiver and transmitter use 8-bit to 10-bit..,1: Receiver and transmitter use 7-bit data.." bitfld.long 0x10 8.--10. "IDLECFG,Idle Configuration" "0: 1 idle character,1: 2 idle characters,2: 4 idle characters,3: 8 idle characters,4: 16 idle characters,5: 32 idle characters,6: 64 idle characters,7: 128 idle characters" newline bitfld.long 0x10 7. "LOOPS,Loop Mode Select" "0: Normal operation - RXD and TXD use separate pins.,1: Loop mode or single-wire mode where transmitter.." bitfld.long 0x10 6. "DOZEEN,Doze Enable" "0: LPUART is enabled in Doze mode.,1: LPUART is disabled in Doze mode ." newline bitfld.long 0x10 5. "RSRC,Receiver Source Select" "0: Provided LOOPS is set RSRC is cleared selects..,1: Single-wire LPUART mode where the TXD pin is.." bitfld.long 0x10 4. "M,9-Bit or 8-Bit Mode Select" "0: Receiver and transmitter use 8-bit data..,1: Receiver and transmitter use 9-bit data.." newline bitfld.long 0x10 3. "WAKE,Receiver Wakeup Method Select" "0: Configures RWU for idle-line wakeup.,1: Configures RWU with address-mark wakeup." bitfld.long 0x10 2. "ILT,Idle Line Type Select" "0: Idle character bit count starts after start bit.,1: Idle character bit count starts after stop bit." newline bitfld.long 0x10 1. "PE,Parity Enable" "0: No hardware parity generation or checking.,1: Parity enabled." bitfld.long 0x10 0. "PT,Parity Type" "0: Even parity.,1: Odd parity." line.long 0x14 "DATA,LPUART Data Register" rbitfld.long 0x14 15. "NOISY,Noisy Data Received" "0: The dataword is received without noise.,1: The data is received with noise." rbitfld.long 0x14 14. "PARITYE,Parity Error" "0: The dataword is received without a parity error.,1: The dataword is received with a parity error." newline bitfld.long 0x14 13. "FRETSC,Frame Error / Transmit Special Character" "0: The dataword is received without a frame error..,1: The dataword is received with a frame error or.." rbitfld.long 0x14 12. "RXEMPT,Receive Buffer Empty" "0: Receive buffer contains valid data.,1: Receive buffer is empty data returned on read is.." newline rbitfld.long 0x14 11. "IDLINE,Idle Line" "0: Receiver was not idle before receiving this..,1: Receiver was idle before receiving this character." bitfld.long 0x14 9. "R9T9,R9T9" "0,1" newline bitfld.long 0x14 8. "R8T8,R8T8" "0,1" bitfld.long 0x14 7. "R7T7,R7T7" "0,1" newline bitfld.long 0x14 6. "R6T6,R6T6" "0,1" bitfld.long 0x14 5. "R5T5,R5T5" "0,1" newline bitfld.long 0x14 4. "R4T4,R4T4" "0,1" bitfld.long 0x14 3. "R3T3,R3T3" "0,1" newline bitfld.long 0x14 2. "R2T2,R2T2" "0,1" bitfld.long 0x14 1. "R1T1,R1T1" "0,1" newline bitfld.long 0x14 0. "R0T0,R0T0" "0,1" line.long 0x18 "MATCH,LPUART Match Address Register" hexmask.long.word 0x18 16.--25. 1. "MA2,Match Address 2" hexmask.long.word 0x18 0.--9. 1. "MA1,Match Address 1" line.long 0x1C "MODIR,LPUART Modem IrDA Register" bitfld.long 0x1C 18. "IREN,Infrared enable" "0: IR disabled.,1: IR enabled." bitfld.long 0x1C 16.--17. "TNP,Transmitter narrow pulse" "0: 1/OSR.,1: 2/OSR.,2: 3/OSR.,3: 4/OSR." newline bitfld.long 0x1C 8.--9. "RTSWATER,Receive RTS Configuration" "0,1,2,3" bitfld.long 0x1C 5. "TXCTSSRC,Transmit CTS Source" "0: CTS input is the CTS_B pin.,1: CTS input is an internal connection to the.." newline bitfld.long 0x1C 4. "TXCTSC,Transmit CTS Configuration" "0: CTS input is sampled at the start of each..,1: CTS input is sampled when the transmitter is idle." bitfld.long 0x1C 3. "RXRTSE,Receiver request-to-send enable" "0: The receiver has no effect on RTS.,1: RTS is deasserted if the receiver data register.." newline bitfld.long 0x1C 2. "TXRTSPOL,Transmitter request-to-send polarity" "0: Transmitter RTS is active low.,1: Transmitter RTS is active high." bitfld.long 0x1C 1. "TXRTSE,Transmitter request-to-send enable" "0: The transmitter has no effect on RTS.,1: When a character is placed into an empty.." newline bitfld.long 0x1C 0. "TXCTSE,Transmitter clear-to-send enable" "0: CTS has no effect on the transmitter.,1: Enables clear-to-send operation. The transmitter.." line.long 0x20 "FIFO,LPUART FIFO Register" rbitfld.long 0x20 23. "TXEMPT,Transmit FIFO/Buffer Empty" "0: Transmit buffer is not empty.,1: Transmit buffer is empty." rbitfld.long 0x20 22. "RXEMPT,Receive FIFO/Buffer Empty" "0: Receive buffer is not empty.,1: Receive buffer is empty." newline eventfld.long 0x20 17. "TXOF,Transmitter FIFO Overflow Flag" "0: No transmit FIFO overflow has occurred since the..,1: At least one transmit FIFO overflow has occurred.." eventfld.long 0x20 16. "RXUF,Receiver FIFO Underflow Flag" "0: No receive FIFO underflow has occurred since the..,1: At least one receive FIFO underflow has occurred.." newline bitfld.long 0x20 15. "TXFLUSH,Transmit FIFO Flush" "0: No flush operation occurs.,1: All data in the transmit FIFO is cleared out." bitfld.long 0x20 14. "RXFLUSH,Receive FIFO Flush" "0: No flush operation occurs.,1: All data in the receive FIFO/buffer is cleared.." newline bitfld.long 0x20 10.--12. "RXIDEN,Receiver Idle Empty Enable" "0: Disable RDRF assertion due to partially filled..,1: Enable RDRF assertion due to partially filled..,2: Enable RDRF assertion due to partially filled..,3: Enable RDRF assertion due to partially filled..,4: Enable RDRF assertion due to partially filled..,5: Enable RDRF assertion due to partially filled..,6: Enable RDRF assertion due to partially filled..,7: Enable RDRF assertion due to partially filled.." bitfld.long 0x20 9. "TXOFE,Transmit FIFO Overflow Interrupt Enable" "0: TXOF flag does not generate an interrupt to the..,1: TXOF flag generates an interrupt to the host." newline bitfld.long 0x20 8. "RXUFE,Receive FIFO Underflow Interrupt Enable" "0: RXUF flag does not generate an interrupt to the..,1: RXUF flag generates an interrupt to the host." bitfld.long 0x20 7. "TXFE,Transmit FIFO Enable" "0: Transmit FIFO is not enabled. Buffer depth is 1.,1: Transmit FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 4.--6. "TXFIFOSIZE,Transmit FIFO Buffer Depth" "0: Transmit FIFO/Buffer depth = 1 dataword.,1: Transmit FIFO/Buffer depth = 4 datawords.,2: Transmit FIFO/Buffer depth = 8 datawords.,3: Transmit FIFO/Buffer depth = 16 datawords.,4: Transmit FIFO/Buffer depth = 32 datawords.,5: Transmit FIFO/Buffer depth = 64 datawords.,6: Transmit FIFO/Buffer depth = 128 datawords.,7: Transmit FIFO/Buffer depth = 256 datawords" bitfld.long 0x20 3. "RXFE,Receive FIFO Enable" "0: Receive FIFO is not enabled. Buffer depth is 1.,1: Receive FIFO is enabled. Buffer depth is.." newline rbitfld.long 0x20 0.--2. "RXFIFOSIZE,Receive FIFO Buffer Depth" "0: Receive FIFO/Buffer depth = 1 dataword.,1: Receive FIFO/Buffer depth = 4 datawords.,2: Receive FIFO/Buffer depth = 8 datawords.,3: Receive FIFO/Buffer depth = 16 datawords.,4: Receive FIFO/Buffer depth = 32 datawords.,5: Receive FIFO/Buffer depth = 64 datawords.,6: Receive FIFO/Buffer depth = 128 datawords.,7: Receive FIFO/Buffer depth = 256 datawords." line.long 0x24 "WATER,LPUART Watermark Register" rbitfld.long 0x24 24.--26. "RXCOUNT,Receive Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 16.--17. "RXWATER,Receive Watermark" "0,1,2,3" newline rbitfld.long 0x24 8.--10. "TXCOUNT,Transmit Counter" "0,1,2,3,4,5,6,7" bitfld.long 0x24 0.--1. "TXWATER,Transmit Watermark" "0,1,2,3" tree.end tree.end sif cpuis("IMXRT1163-CM4")||(cpuis("IMXRT1165-CM4")||cpuis("IMXRT1166-CM4")) tree "MCM" base ad:0xE0080000 rgroup.word 0x0++0x3 line.word 0x0 "PLREV,SoC-defined platform revision" hexmask.word 0x0 0.--15. 1. "PLREV,The PLREV[15:0] field is specified by an platform input signal to define a software-visible revision number." line.word 0x2 "PCT,Processor core type" hexmask.word 0x2 0.--15. 1. "PCT,This MCM design supports the ARM Cortex M4 core. The following value identifies this core complex." rgroup.long 0x4++0x3 line.long 0x0 "MEMCFG,Memory configuration" hexmask.long.byte 0x0 8.--11. 1. "TCRAMLSZ,TCRAML size" hexmask.long.byte 0x0 2.--5. 1. "TCRAMUSZ,TCRAMU size" rgroup.word 0x8++0x3 line.word 0x0 "PLASC,Crossbar Switch (AXBS) Slave Configuration" hexmask.word.byte 0x0 0.--7. 1. "ASC,Each bit in the ASC field indicates whether there is a corresponding connection to the crossbar switch's slave input port." line.word 0x2 "PLAMC,Crossbar Switch (AXBS) Master Configuration" hexmask.word.byte 0x2 0.--7. 1. "AMC,Each bit in the AMC field indicates whether there is a corresponding connection to the AXBS master input port." group.long 0xC++0x7 line.long 0x0 "CR,Control Register" bitfld.long 0x0 30. "CTCMWP,Code TCM Write Protect" "0,1" bitfld.long 0x0 28.--29. "CTCMAP,Code TCM arbitration priority" "0: Round robin,1: Special round robin (favors TCM backoor accesses..,2: Fixed priority. Processor has highest backdoor..,3: Fixed priority. Backdoor has highest processor.." newline bitfld.long 0x0 26. "STCMWP,System TCM write protect" "0,1" bitfld.long 0x0 24.--25. "STCMAP,System TCM arbitration priority" "0: Round robin,1: Special round robin (favors TCM backoor accesses..,2: Fixed priority. Processor has highest backdoor..,3: Fixed priority. Backdoor has highest processor.." newline bitfld.long 0x0 9. "CBRR,Crossbar round-robin arbitration enable" "0: Fixed-priority arbitration,1: Round-robin arbitration" hexmask.long.word 0x0 0.--8. 1. "STATUS,Status bits" line.long 0x4 "ISCR,Interrupt Status and Control Register" bitfld.long 0x4 31. "FIDCE,FPU input denormal interrupt enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x4 28. "FIXCE,FPU inexact interrupt enable" "0: Disable interrupt,1: Enable interrupt" newline bitfld.long 0x4 27. "FUFCE,FPU underflow interrupt enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x4 26. "FOFCE,FPU overflow interrupt enable" "0: Disable interrupt,1: Enable interrupt" newline bitfld.long 0x4 25. "FDZCE,FPU divide-by-zero interrupt enable" "0: Disable interrupt,1: Enable interrupt" bitfld.long 0x4 24. "FIOCE,FPU invalid operation interrupt enable" "0: Disable interrupt,1: Enable interrupt" newline bitfld.long 0x4 20. "CWBEE,Cache write buffer error enable" "0: Disable error interrupt,1: Enable error interrupt" rbitfld.long 0x4 15. "FIDC,FPU input denormal interrupt status" "0: No interrupt,1: Interrupt occurred" newline rbitfld.long 0x4 12. "FIXC,FPU inexact interrupt status" "0: No interrupt,1: Interrupt occurred" rbitfld.long 0x4 11. "FUFC,FPU underflow interrupt status" "0: No interrupt,1: Interrupt occurred" newline rbitfld.long 0x4 10. "FOFC,FPU overflow interrupt status" "0: No interrupt,1: Interrupt occurred" rbitfld.long 0x4 9. "FDZC,FPU divide-by-zero interrupt status" "0: No interrupt,1: Interrupt occurred" newline rbitfld.long 0x4 8. "FIOC,FPU invalid operation interrupt status" "0: No interrupt,1: Interrupt occurred" eventfld.long 0x4 4. "CWBER,Cache write buffer error status" "0: No error,1: Error occurred" rgroup.long 0x20++0xB line.long 0x0 "FADR,Fault address register" hexmask.long 0x0 0.--31. 1. "ADDRESS,Fault address" line.long 0x4 "FATR,Fault attributes register" bitfld.long 0x4 31. "BEOVR,Bus error overrun" "0: No bus error overrun,1: Bus error overrun occurred. The FADR and FDR.." hexmask.long.byte 0x4 8.--11. 1. "BEMN,Bus error master number" newline bitfld.long 0x4 7. "BEWT,Bus error write" "0: Read access,1: Write access" bitfld.long 0x4 4.--5. "BESZ,Bus error size" "0: 8-bit access,1: 16-bit access,2: 32-bit access,?" newline bitfld.long 0x4 1. "BEMD,Bus error privilege level" "0: User mode,1: Supervisor/privileged mode" bitfld.long 0x4 0. "BEDA,Bus error access type" "0: Instruction,1: Data" line.long 0x8 "FDR,Fault data register" hexmask.long 0x8 0.--31. 1. "DATA,Fault data" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x400)++0x3 line.long 0x0 "LMDR$1,Local Memory Descriptor Register" rbitfld.long 0x0 31. "V,Local memory Valid bit. This read-only field defines the validity (presence) of the local memory." "0: LMEMn is not present.,1: LMEMn is present." rbitfld.long 0x0 28. "LMSZH,LMEM Size 'Hole'" "0: LMEMn is a power-of-2 capacity.,1: LMEMn is not a power-of-2 with a capacity is.." newline hexmask.long.byte 0x0 24.--27. 1. "LMSZ,LMEM Size" hexmask.long.byte 0x0 20.--23. 1. "WY,Level 1 Cache Ways" newline rbitfld.long 0x0 17.--19. "DPW,LMEM Data Path Width. This read-only field defines the width of the local memory." "?,?,2: LMEMn 32-bits wide,3: LMEMn 64-bits wide,?,?,?,?" rbitfld.long 0x0 16. "RO,Read-Only" "0: Writes to the LMDRn[7:0] are allowed.,1: Writes to the LMDRn[7:0] are ignored." newline rbitfld.long 0x0 13.--15. "MT,Memory Type" "0: code TCM,1: system TCM,2: PC Cache,3: PS Cache,?,?,?,?" hexmask.long.byte 0x0 4.--7. 1. "CF1,Control Field 1 - for Cache Parity control functions" newline hexmask.long.byte 0x0 0.--3. 1. "CF0,Control Field 0" repeat.end group.long 0x480++0x3 line.long 0x0 "LMPECR,LMEM Parity & ECC Control Register" bitfld.long 0x0 21. "ECPI,Enable Cache Parity IRQ" "0: enabled,1: disabled" bitfld.long 0x0 20. "ECPR,Enable Cache Parity Reporting" "0: reporting enabled,1: reporting disabled" newline bitfld.long 0x0 9. "ER1BI,Enable RAM ECC 1-bit Interrupt" "0: Interrupt is disabled,1: bit Interrupt" bitfld.long 0x0 8. "ER1BR,Enable RAM ECC 1-bit Reporting" "0: reporting enabled,1: bit Reporting" newline bitfld.long 0x0 1. "ERNCI,Enable RAM Non-correctable ECC Interrupt" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x0 0. "ERNCR,Enable RAM ECC Non-correctable Reporting" "0: reporting enabled,1: reporting disabled" group.long 0x488++0x3 line.long 0x0 "LMPEIR,LMEM Parity & ECC Interrupt Register" rbitfld.long 0x0 31. "V,Valid bit" "0,1" hexmask.long.byte 0x0 24.--28. 1. "PEELOC,Parity or ECC Error Location" newline hexmask.long.byte 0x0 16.--23. 1. "PE,Parity Error" hexmask.long.byte 0x0 8.--15. 1. "E1B,E1Bn = ECC 1-bit Error n" newline hexmask.long.byte 0x0 0.--7. 1. "ENC,ENCn = ECC Non-correctable Error n" rgroup.long 0x490++0x3 line.long 0x0 "LMFAR,LMEM Fault Address Register" hexmask.long 0x0 0.--31. 1. "EFADD,ECC Fault Address" group.long 0x494++0x3 line.long 0x0 "LMFATR,LMEM Fault Attribute Register" rbitfld.long 0x0 31. "OVR,Overrun" "0,1" rbitfld.long 0x0 24. "WORDID,ID of the word which has ECC error" "0,1" newline hexmask.long.byte 0x0 8.--15. 1. "PEFMST,Parity/ECC Fault Master Number" rbitfld.long 0x0 7. "PEFW,Parity/ECC Fault Write" "0,1" newline bitfld.long 0x0 4.--6. "PEFSIZE,Parity/ECC Fault Master Size 3'b000 = 8-bit access 3'b001 = 16-bit access 3'b010 = 32-bit access 3'b011 = 64-bit access 3'b1xx = Reserved" "0,1,2,3,4,5,6,7" hexmask.long.byte 0x0 0.--3. 1. "PEFPRT,Parity/ECC Fault Protection FATR[3] is Cacheable: 0=Non-cacheable 1=Cacheable FATR[2] is Bufferable: 0=Non-bufferable 1=Bufferable FATR[1] is Mode: 0=User mode 1=Supervisor mode FATR[0] is Type: 0=I-Fetch 1=Data" rgroup.long 0x4A0++0x7 line.long 0x0 "LMFDHR,LMEM Fault Data High Register" hexmask.long 0x0 0.--31. 1. "PEFDH,Parity or ECC Fault Data High" line.long 0x4 "LMFDLR,LMEM Fault Data Low Register" hexmask.long 0x4 0.--31. 1. "PEFDL,Parity or ECC Fault Data Low" tree.end endif tree "MECC" base ad:0x0 tree "MECC1" base ad:0x40014000 group.long 0x0++0x3B line.long 0x0 "ERR_STATUS,Error Interrupt Status Register" eventfld.long 0x0 15. "ADDR_ERR3,OCRAM Access Error On Bank3" "0: OCRAM access error does not happen on OCRAM bank3.,1: OCRAM access error happens on OCRAM bank3." newline eventfld.long 0x0 14. "ADDR_ERR2,OCRAM Access Error On Bank2" "0: OCRAM access error does not happen on OCRAM bank2.,1: OCRAM access error happens on OCRAM bank2." newline eventfld.long 0x0 13. "ADDR_ERR1,OCRAM Access Error On Bank1" "0: OCRAM access error does not happen on OCRAM bank1.,1: OCRAM access error happens on OCRAM bank1." newline eventfld.long 0x0 12. "ADDR_ERR0,OCRAM Access Error On Bank0" "0: OCRAM access error does not happen on OCRAM bank0.,1: OCRAM access error happens on OCRAM bank0." newline eventfld.long 0x0 11. "STRB_ERR3,AXI Strobe Error On OCRAM Bank3" "0: AXI strobe error does not happen on OCRAM bank3.,1: AXI strobe error happens on OCRAM bank3." newline eventfld.long 0x0 10. "STRB_ERR2,AXI Strobe Error On OCRAM Bank2" "0: AXI strobe error does not happen on OCRAM bank2.,1: AXI strobe error happens on OCRAM bank2." newline eventfld.long 0x0 9. "STRB_ERR1,AXI Strobe Error On OCRAM Bank1" "0: AXI strobe error does not happen on OCRAM bank1.,1: AXI strobe error happens on OCRAM bank1." newline eventfld.long 0x0 8. "STRB_ERR0,AXI Strobe Error On OCRAM Bank0" "0: AXI strobe error does not happen on OCRAM bank0.,1: AXI strobe error happens on OCRAM bank0." newline eventfld.long 0x0 7. "MULTI_ERR3,Multiple Bits Error On OCRAM Bank3" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank3." newline eventfld.long 0x0 6. "MULTI_ERR2,Multiple Bits Error On OCRAM Bank2" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank2." newline eventfld.long 0x0 5. "MULTI_ERR1,Multiple Bits Error On OCRAM Bank1" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank1." newline eventfld.long 0x0 4. "MULTI_ERR0,Multiple Bits Error On OCRAM Bank0" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank0." newline eventfld.long 0x0 3. "SINGLE_ERR3,Single Bit Error On OCRAM Bank3" "0: Single bit error does not happen on OCRAM bank3.,1: Single bit error happens on OCRAM bank3." newline eventfld.long 0x0 2. "SINGLE_ERR2,Single Bit Error On OCRAM Bank2" "0: Single bit error does not happen on OCRAM bank2.,1: Single bit error happens on OCRAM bank2." newline eventfld.long 0x0 1. "SINGLE_ERR1,Single Bit Error On OCRAM Bank1" "0: Single bit error does not happen on OCRAM bank1.,1: Single bit error happens on OCRAM bank1." newline eventfld.long 0x0 0. "SINGLE_ERR0,Single Bit Error On OCRAM Bank0" "0: Single bit error does not happen on OCRAM bank0.,1: Single bit error happens on OCRAM bank0." line.long 0x4 "ERR_STAT_EN,Error Interrupt Status Enable Register" bitfld.long 0x4 15. "ADDR_ERR3_STAT_EN,OCRAM Access Error Status Enable On Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 14. "ADDR_ERR2_STAT_EN,OCRAM Access Error Status Enable On Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 13. "ADDR_ERR1_STAT_EN,OCRAM Access Error Status Enable On Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 12. "ADDR_ERR0_STAT_EN,OCRAM Access Error Status Enable On Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 11. "STRB_ERR3_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 10. "STRB_ERR2_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 9. "STRB_ERR1_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 8. "STRB_ERR0_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 7. "MULTI_ERR3_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 6. "MULTI_ERR2_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 5. "MULTI_ERR1_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 4. "MULTI_ERR0_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 3. "SINGLE_ERR3_STAT_EN,Single Bit Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 2. "SINGLE_ERR2_STAT_EN,Single Bit Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 1. "SINGLE_ERR1_STAT_EN,Single Bit Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 0. "SINGLE_ERR0_STAT_EN,Single Bit Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" line.long 0x8 "ERR_SIG_EN,Error Interrupt Enable Register" bitfld.long 0x8 15. "ADDR_ERR3_SIG_EN,OCRAM Access Error Interrupt Enable On Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 14. "ADDR_ERR2_SIG_EN,OCRAM Access Error Interrupt Enable On Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "ADDR_ERR1_SIG_EN,OCRAM Access Error Interrupt Enable On Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "ADDR_ERR0_SIG_EN,OCRAM Access Error Interrupt Enable On Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "STRB_ERR3_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "STRB_ERR2_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "STRB_ERR1_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "STRB_ERR0_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 7. "MULTI_ERR3_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 6. "MULTI_ERR2_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 5. "MULTI_ERR1_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 4. "MULTI_ERR0_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "SINGLE_ERR3_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 2. "SINGLE_ERR2_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "SINGLE_ERR1_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "SINGLE_ERR0_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" line.long 0xC "ERR_DATA_INJ_LOW0,Error Injection On LOW 32 bits Of OCRAM Bank0 Write Data" hexmask.long 0xC 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank0 Write Data" line.long 0x10 "ERR_DATA_INJ_HIGH0,Error Injection On HIGH 32 bits Of OCRAM Bank0 Write Data" hexmask.long 0x10 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank0 Write Data" line.long 0x14 "ERR_ECC_INJ0,Error Injection On 8 bits ECC code Of OCRAM Bank0 Write Data" hexmask.long.byte 0x14 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank0 Write Data" line.long 0x18 "ERR_DATA_INJ_LOW1,Error Injection On LOW 32 bits Of OCRAM Bank1 Write Data" hexmask.long 0x18 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank1 Write Data" line.long 0x1C "ERR_DATA_INJ_HIGH1,Error Injection On HIGH 32 bits Of OCRAM Bank1 Write Data" hexmask.long 0x1C 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank1 Write Data" line.long 0x20 "ERR_ECC_INJ1,Error Injection On 8 bits ECC code Of OCRAM Bank1 Write Data" hexmask.long.byte 0x20 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank1 Write Data" line.long 0x24 "ERR_DATA_INJ_LOW2,Error Injection On LOW 32 bits Of OCRAM Bank2 Write Data" hexmask.long 0x24 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank2 Write Data" line.long 0x28 "ERR_DATA_INJ_HIGH2,Error Injection On HIGH 32 bits Of OCRAM Bank2 Write Data" hexmask.long 0x28 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank2 Write Data" line.long 0x2C "ERR_ECC_INJ2,Error Injection On 8 bits ECC code Of OCRAM Bank2 Write Data" hexmask.long.byte 0x2C 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank2 Write Data" line.long 0x30 "ERR_DATA_INJ_LOW3,Error Injection On LOW 32 bits Of OCRAM Bank3 Write Data" hexmask.long 0x30 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank3 Write Data" line.long 0x34 "ERR_DATA_INJ_HIGH3,Error Injection On HIGH 32 bits Of OCRAM Bank3 Write Data" hexmask.long 0x34 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank3 Write Data" line.long 0x38 "ERR_ECC_INJ3,Error Injection On 8 bits ECC code Of OCRAM Bank3 Write Data" hexmask.long.byte 0x38 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank3 Write Data" rgroup.long 0x3C++0x7F line.long 0x0 "SINGLE_ERR_ADDR_ECC0,Single Error Address And ECC code On OCRAM Bank0" hexmask.long.tbyte 0x0 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank0" newline hexmask.long.byte 0x0 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank0" line.long 0x4 "SINGLE_ERR_DATA_LOW0,LOW 32 Bits Single Error Read Data On OCRAM Bank0" hexmask.long 0x4 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank0" line.long 0x8 "SINGLE_ERR_DATA_HIGH0,HIGH 32 Bits Single Error Read Data On OCRAM Bank0" hexmask.long 0x8 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank0" line.long 0xC "SINGLE_ERR_POS_LOW0,LOW Single Error Bit Position On OCRAM Bank0" hexmask.long 0xC 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank0" line.long 0x10 "SINGLE_ERR_POS_HIGH0,HIGH Single Error Bit Position On OCRAM Bank0" hexmask.long 0x10 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank0" line.long 0x14 "SINGLE_ERR_ADDR_ECC1,Single Error Address And ECC code On OCRAM Bank1" hexmask.long.tbyte 0x14 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank1" newline hexmask.long.byte 0x14 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank1" line.long 0x18 "SINGLE_ERR_DATA_LOW1,LOW 32 Bits Single Error Read Data On OCRAM Bank1" hexmask.long 0x18 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank1" line.long 0x1C "SINGLE_ERR_DATA_HIGH1,HIGH 32 Bits Single Error Read Data On OCRAM Bank1" hexmask.long 0x1C 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank1" line.long 0x20 "SINGLE_ERR_POS_LOW1,LOW Single Error Bit Position On OCRAM Bank1" hexmask.long 0x20 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank1" line.long 0x24 "SINGLE_ERR_POS_HIGH1,HIGH Single Error Bit Position On OCRAM Bank1" hexmask.long 0x24 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank1" line.long 0x28 "SINGLE_ERR_ADDR_ECC2,Single Error Address And ECC code On OCRAM Bank2" hexmask.long.tbyte 0x28 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank2" newline hexmask.long.byte 0x28 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank2" line.long 0x2C "SINGLE_ERR_DATA_LOW2,LOW 32 Bits Single Error Read Data On OCRAM Bank2" hexmask.long 0x2C 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank2" line.long 0x30 "SINGLE_ERR_DATA_HIGH2,HIGH 32 Bits Single Error Read Data On OCRAM Bank2" hexmask.long 0x30 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank2" line.long 0x34 "SINGLE_ERR_POS_LOW2,LOW Single Error Bit Position On OCRAM Bank2" hexmask.long 0x34 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank2" line.long 0x38 "SINGLE_ERR_POS_HIGH2,HIGH Single Error Bit Position On OCRAM Bank2" hexmask.long 0x38 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank2" line.long 0x3C "SINGLE_ERR_ADDR_ECC3,Single Error Address And ECC code On OCRAM Bank3" hexmask.long.tbyte 0x3C 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank3" newline hexmask.long.byte 0x3C 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank3" line.long 0x40 "SINGLE_ERR_DATA_LOW3,LOW 32 Bits Single Error Read Data On OCRAM Bank3" hexmask.long 0x40 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank3" line.long 0x44 "SINGLE_ERR_DATA_HIGH3,HIGH 32 Bits Single Error Read Data On OCRAM Bank3" hexmask.long 0x44 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank3" line.long 0x48 "SINGLE_ERR_POS_LOW3,LOW Single Error Bit Position On OCRAM Bank3" hexmask.long 0x48 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank3" line.long 0x4C "SINGLE_ERR_POS_HIGH3,HIGH Single Error Bit Position On OCRAM Bank3" hexmask.long 0x4C 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank3" line.long 0x50 "MULTI_ERR_ADDR_ECC0,Multiple Error Address And ECC code On OCRAM Bank0" hexmask.long.tbyte 0x50 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank0" newline hexmask.long.byte 0x50 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank0" line.long 0x54 "MULTI_ERR_DATA_LOW0,LOW 32 Bits Multiple Error Read Data On OCRAM Bank0" hexmask.long 0x54 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank0" line.long 0x58 "MULTI_ERR_DATA_HIGH0,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank0" hexmask.long 0x58 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank0" line.long 0x5C "MULTI_ERR_ADDR_ECC1,Multiple Error Address And ECC code On OCRAM Bank1" hexmask.long.tbyte 0x5C 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank1" newline hexmask.long.byte 0x5C 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank1" line.long 0x60 "MULTI_ERR_DATA_LOW1,LOW 32 Bits Multiple Error Read Data On OCRAM Bank1" hexmask.long 0x60 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank1" line.long 0x64 "MULTI_ERR_DATA_HIGH1,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank1" hexmask.long 0x64 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank1" line.long 0x68 "MULTI_ERR_ADDR_ECC2,Multiple Error Address And ECC code On OCRAM Bank2" hexmask.long.tbyte 0x68 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank2" newline hexmask.long.byte 0x68 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank2" line.long 0x6C "MULTI_ERR_DATA_LOW2,LOW 32 Bits Multiple Error Read Data On OCRAM Bank2" hexmask.long 0x6C 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank2" line.long 0x70 "MULTI_ERR_DATA_HIGH2,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank2" hexmask.long 0x70 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank2" line.long 0x74 "MULTI_ERR_ADDR_ECC3,Multiple Error Address And ECC code On OCRAM Bank3" hexmask.long.tbyte 0x74 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank3" newline hexmask.long.byte 0x74 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank3" line.long 0x78 "MULTI_ERR_DATA_LOW3,LOW 32 Bits Multiple Error Read Data On OCRAM Bank3" hexmask.long 0x78 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank3" line.long 0x7C "MULTI_ERR_DATA_HIGH3,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank3" hexmask.long 0x7C 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank3" group.long 0x100++0x3 line.long 0x0 "PIPE_ECC_EN,OCRAM Pipeline And ECC Enable" bitfld.long 0x0 4. "ECC_EN,ECC Function Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 3. "WRITE_ADDR_PIPE_EN,Write Address Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 2. "WRITE_DATA_PIPE_EN,Write Data Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 1. "READ_ADDR_PIPE_EN,Read Address Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 0. "READ_DATA_WAIT_EN,Read Data Wait Enable" "0: Disable.,1: Enable." rgroup.long 0x104++0x3 line.long 0x0 "PENDING_STAT,Pending Status" bitfld.long 0x0 3. "WRITE_ADDR_PIPE_PENDING,Write Address Pipeline Pending" "0: No update pending status for WRITE_ADDR_PIPE_EN.,1: When WRITE_ADDR_PIPE_EN register bit is changed.." newline bitfld.long 0x0 2. "WRITE_DATA_PIPE_PENDING,Write Data Pipeline Pending" "0: No update pending status for WRITE_DATA_PIPE_EN.,1: When WRITE_DATA_PIPE_EN register bit is changed.." newline bitfld.long 0x0 1. "READ_ADDR_PIPE_PENDING,Read Address Pipeline Pending" "0: No update pending status for READ_ADDR_PIPE_EN.,1: When READ_ADDR_PIPE_EN register bit is changed.." newline bitfld.long 0x0 0. "READ_DATA_WAIT_PENDING,Read Data Wait Pending" "0: No update pending status for READ_DATA_WAIT_EN.,1: When READ_DATA_WAIT_EN register bit is changed.." tree.end tree "MECC2" base ad:0x40018000 group.long 0x0++0x3B line.long 0x0 "ERR_STATUS,Error Interrupt Status Register" eventfld.long 0x0 15. "ADDR_ERR3,OCRAM Access Error On Bank3" "0: OCRAM access error does not happen on OCRAM bank3.,1: OCRAM access error happens on OCRAM bank3." newline eventfld.long 0x0 14. "ADDR_ERR2,OCRAM Access Error On Bank2" "0: OCRAM access error does not happen on OCRAM bank2.,1: OCRAM access error happens on OCRAM bank2." newline eventfld.long 0x0 13. "ADDR_ERR1,OCRAM Access Error On Bank1" "0: OCRAM access error does not happen on OCRAM bank1.,1: OCRAM access error happens on OCRAM bank1." newline eventfld.long 0x0 12. "ADDR_ERR0,OCRAM Access Error On Bank0" "0: OCRAM access error does not happen on OCRAM bank0.,1: OCRAM access error happens on OCRAM bank0." newline eventfld.long 0x0 11. "STRB_ERR3,AXI Strobe Error On OCRAM Bank3" "0: AXI strobe error does not happen on OCRAM bank3.,1: AXI strobe error happens on OCRAM bank3." newline eventfld.long 0x0 10. "STRB_ERR2,AXI Strobe Error On OCRAM Bank2" "0: AXI strobe error does not happen on OCRAM bank2.,1: AXI strobe error happens on OCRAM bank2." newline eventfld.long 0x0 9. "STRB_ERR1,AXI Strobe Error On OCRAM Bank1" "0: AXI strobe error does not happen on OCRAM bank1.,1: AXI strobe error happens on OCRAM bank1." newline eventfld.long 0x0 8. "STRB_ERR0,AXI Strobe Error On OCRAM Bank0" "0: AXI strobe error does not happen on OCRAM bank0.,1: AXI strobe error happens on OCRAM bank0." newline eventfld.long 0x0 7. "MULTI_ERR3,Multiple Bits Error On OCRAM Bank3" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank3." newline eventfld.long 0x0 6. "MULTI_ERR2,Multiple Bits Error On OCRAM Bank2" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank2." newline eventfld.long 0x0 5. "MULTI_ERR1,Multiple Bits Error On OCRAM Bank1" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank1." newline eventfld.long 0x0 4. "MULTI_ERR0,Multiple Bits Error On OCRAM Bank0" "0: Multiple bits error does not happen on OCRAM..,1: Multiple bits error happens on OCRAM bank0." newline eventfld.long 0x0 3. "SINGLE_ERR3,Single Bit Error On OCRAM Bank3" "0: Single bit error does not happen on OCRAM bank3.,1: Single bit error happens on OCRAM bank3." newline eventfld.long 0x0 2. "SINGLE_ERR2,Single Bit Error On OCRAM Bank2" "0: Single bit error does not happen on OCRAM bank2.,1: Single bit error happens on OCRAM bank2." newline eventfld.long 0x0 1. "SINGLE_ERR1,Single Bit Error On OCRAM Bank1" "0: Single bit error does not happen on OCRAM bank1.,1: Single bit error happens on OCRAM bank1." newline eventfld.long 0x0 0. "SINGLE_ERR0,Single Bit Error On OCRAM Bank0" "0: Single bit error does not happen on OCRAM bank0.,1: Single bit error happens on OCRAM bank0." line.long 0x4 "ERR_STAT_EN,Error Interrupt Status Enable Register" bitfld.long 0x4 15. "ADDR_ERR3_STAT_EN,OCRAM Access Error Status Enable On Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 14. "ADDR_ERR2_STAT_EN,OCRAM Access Error Status Enable On Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 13. "ADDR_ERR1_STAT_EN,OCRAM Access Error Status Enable On Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 12. "ADDR_ERR0_STAT_EN,OCRAM Access Error Status Enable On Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 11. "STRB_ERR3_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 10. "STRB_ERR2_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 9. "STRB_ERR1_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 8. "STRB_ERR0_STAT_EN,AXI Strobe Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 7. "MULTI_ERR3_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 6. "MULTI_ERR2_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 5. "MULTI_ERR1_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 4. "MULTI_ERR0_STAT_EN,Multiple Bits Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x4 3. "SINGLE_ERR3_STAT_EN,Single Bit Error Status Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x4 2. "SINGLE_ERR2_STAT_EN,Single Bit Error Status Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x4 1. "SINGLE_ERR1_STAT_EN,Single Bit Error Status Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x4 0. "SINGLE_ERR0_STAT_EN,Single Bit Error Status Enable On OCRAM Bank0" "0: Disabled,1: Enabled" line.long 0x8 "ERR_SIG_EN,Error Interrupt Enable Register" bitfld.long 0x8 15. "ADDR_ERR3_SIG_EN,OCRAM Access Error Interrupt Enable On Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 14. "ADDR_ERR2_SIG_EN,OCRAM Access Error Interrupt Enable On Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 13. "ADDR_ERR1_SIG_EN,OCRAM Access Error Interrupt Enable On Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 12. "ADDR_ERR0_SIG_EN,OCRAM Access Error Interrupt Enable On Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 11. "STRB_ERR3_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 10. "STRB_ERR2_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 9. "STRB_ERR1_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 8. "STRB_ERR0_SIG_EN,AXI Strobe Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 7. "MULTI_ERR3_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 6. "MULTI_ERR2_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 5. "MULTI_ERR1_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 4. "MULTI_ERR0_SIG_EN,Multiple Bits Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" newline bitfld.long 0x8 3. "SINGLE_ERR3_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank3" "0: Disabled,1: Enabled" newline bitfld.long 0x8 2. "SINGLE_ERR2_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank2" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "SINGLE_ERR1_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank1" "0: Disabled,1: Enabled" newline bitfld.long 0x8 0. "SINGLE_ERR0_SIG_EN,Single Bit Error Interrupt Enable On OCRAM Bank0" "0: Disabled,1: Enabled" line.long 0xC "ERR_DATA_INJ_LOW0,Error Injection On LOW 32 bits Of OCRAM Bank0 Write Data" hexmask.long 0xC 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank0 Write Data" line.long 0x10 "ERR_DATA_INJ_HIGH0,Error Injection On HIGH 32 bits Of OCRAM Bank0 Write Data" hexmask.long 0x10 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank0 Write Data" line.long 0x14 "ERR_ECC_INJ0,Error Injection On 8 bits ECC code Of OCRAM Bank0 Write Data" hexmask.long.byte 0x14 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank0 Write Data" line.long 0x18 "ERR_DATA_INJ_LOW1,Error Injection On LOW 32 bits Of OCRAM Bank1 Write Data" hexmask.long 0x18 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank1 Write Data" line.long 0x1C "ERR_DATA_INJ_HIGH1,Error Injection On HIGH 32 bits Of OCRAM Bank1 Write Data" hexmask.long 0x1C 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank1 Write Data" line.long 0x20 "ERR_ECC_INJ1,Error Injection On 8 bits ECC code Of OCRAM Bank1 Write Data" hexmask.long.byte 0x20 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank1 Write Data" line.long 0x24 "ERR_DATA_INJ_LOW2,Error Injection On LOW 32 bits Of OCRAM Bank2 Write Data" hexmask.long 0x24 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank2 Write Data" line.long 0x28 "ERR_DATA_INJ_HIGH2,Error Injection On HIGH 32 bits Of OCRAM Bank2 Write Data" hexmask.long 0x28 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank2 Write Data" line.long 0x2C "ERR_ECC_INJ2,Error Injection On 8 bits ECC code Of OCRAM Bank2 Write Data" hexmask.long.byte 0x2C 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank2 Write Data" line.long 0x30 "ERR_DATA_INJ_LOW3,Error Injection On LOW 32 bits Of OCRAM Bank3 Write Data" hexmask.long 0x30 0.--31. 1. "ERR_DATA_INJ,Error Injection On LOW 32 bits Of OCRAM Bank3 Write Data" line.long 0x34 "ERR_DATA_INJ_HIGH3,Error Injection On HIGH 32 bits Of OCRAM Bank3 Write Data" hexmask.long 0x34 0.--31. 1. "ERR_DATA_INJ,Error Injection On HIGH 32 bits Of OCRAM Bank3 Write Data" line.long 0x38 "ERR_ECC_INJ3,Error Injection On 8 bits ECC code Of OCRAM Bank3 Write Data" hexmask.long.byte 0x38 0.--7. 1. "ERR_ECC_INJ,Error Injection On 8 bits ECC code Of OCRAM Bank3 Write Data" rgroup.long 0x3C++0x7F line.long 0x0 "SINGLE_ERR_ADDR_ECC0,Single Error Address And ECC code On OCRAM Bank0" hexmask.long.tbyte 0x0 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank0" newline hexmask.long.byte 0x0 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank0" line.long 0x4 "SINGLE_ERR_DATA_LOW0,LOW 32 Bits Single Error Read Data On OCRAM Bank0" hexmask.long 0x4 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank0" line.long 0x8 "SINGLE_ERR_DATA_HIGH0,HIGH 32 Bits Single Error Read Data On OCRAM Bank0" hexmask.long 0x8 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank0" line.long 0xC "SINGLE_ERR_POS_LOW0,LOW Single Error Bit Position On OCRAM Bank0" hexmask.long 0xC 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank0" line.long 0x10 "SINGLE_ERR_POS_HIGH0,HIGH Single Error Bit Position On OCRAM Bank0" hexmask.long 0x10 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank0" line.long 0x14 "SINGLE_ERR_ADDR_ECC1,Single Error Address And ECC code On OCRAM Bank1" hexmask.long.tbyte 0x14 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank1" newline hexmask.long.byte 0x14 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank1" line.long 0x18 "SINGLE_ERR_DATA_LOW1,LOW 32 Bits Single Error Read Data On OCRAM Bank1" hexmask.long 0x18 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank1" line.long 0x1C "SINGLE_ERR_DATA_HIGH1,HIGH 32 Bits Single Error Read Data On OCRAM Bank1" hexmask.long 0x1C 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank1" line.long 0x20 "SINGLE_ERR_POS_LOW1,LOW Single Error Bit Position On OCRAM Bank1" hexmask.long 0x20 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank1" line.long 0x24 "SINGLE_ERR_POS_HIGH1,HIGH Single Error Bit Position On OCRAM Bank1" hexmask.long 0x24 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank1" line.long 0x28 "SINGLE_ERR_ADDR_ECC2,Single Error Address And ECC code On OCRAM Bank2" hexmask.long.tbyte 0x28 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank2" newline hexmask.long.byte 0x28 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank2" line.long 0x2C "SINGLE_ERR_DATA_LOW2,LOW 32 Bits Single Error Read Data On OCRAM Bank2" hexmask.long 0x2C 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank2" line.long 0x30 "SINGLE_ERR_DATA_HIGH2,HIGH 32 Bits Single Error Read Data On OCRAM Bank2" hexmask.long 0x30 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank2" line.long 0x34 "SINGLE_ERR_POS_LOW2,LOW Single Error Bit Position On OCRAM Bank2" hexmask.long 0x34 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank2" line.long 0x38 "SINGLE_ERR_POS_HIGH2,HIGH Single Error Bit Position On OCRAM Bank2" hexmask.long 0x38 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank2" line.long 0x3C "SINGLE_ERR_ADDR_ECC3,Single Error Address And ECC code On OCRAM Bank3" hexmask.long.tbyte 0x3C 8.--26. 1. "SINGLE_ERR_ADDR,Single Error Address On OCRAM Bank3" newline hexmask.long.byte 0x3C 0.--7. 1. "SINGLE_ERR_ECC,Single Error ECC code On OCRAM Bank3" line.long 0x40 "SINGLE_ERR_DATA_LOW3,LOW 32 Bits Single Error Read Data On OCRAM Bank3" hexmask.long 0x40 0.--31. 1. "SINGLE_ERR_DATA,LOW 32 Bits Single Error Read Data On OCRAM Bank3" line.long 0x44 "SINGLE_ERR_DATA_HIGH3,HIGH 32 Bits Single Error Read Data On OCRAM Bank3" hexmask.long 0x44 0.--31. 1. "SINGLE_ERR_DATA,HIGH 32 Bits Single Error Read Data On OCRAM Bank3" line.long 0x48 "SINGLE_ERR_POS_LOW3,LOW Single Error Bit Position On OCRAM Bank3" hexmask.long 0x48 0.--31. 1. "SINGLE_ERR_POS,LOW Single Error Bit Position On OCRAM Bank3" line.long 0x4C "SINGLE_ERR_POS_HIGH3,HIGH Single Error Bit Position On OCRAM Bank3" hexmask.long 0x4C 0.--31. 1. "SINGLE_ERR_POS,HIGH Single Error Bit Position On OCRAM Bank3" line.long 0x50 "MULTI_ERR_ADDR_ECC0,Multiple Error Address And ECC code On OCRAM Bank0" hexmask.long.tbyte 0x50 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank0" newline hexmask.long.byte 0x50 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank0" line.long 0x54 "MULTI_ERR_DATA_LOW0,LOW 32 Bits Multiple Error Read Data On OCRAM Bank0" hexmask.long 0x54 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank0" line.long 0x58 "MULTI_ERR_DATA_HIGH0,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank0" hexmask.long 0x58 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank0" line.long 0x5C "MULTI_ERR_ADDR_ECC1,Multiple Error Address And ECC code On OCRAM Bank1" hexmask.long.tbyte 0x5C 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank1" newline hexmask.long.byte 0x5C 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank1" line.long 0x60 "MULTI_ERR_DATA_LOW1,LOW 32 Bits Multiple Error Read Data On OCRAM Bank1" hexmask.long 0x60 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank1" line.long 0x64 "MULTI_ERR_DATA_HIGH1,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank1" hexmask.long 0x64 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank1" line.long 0x68 "MULTI_ERR_ADDR_ECC2,Multiple Error Address And ECC code On OCRAM Bank2" hexmask.long.tbyte 0x68 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank2" newline hexmask.long.byte 0x68 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank2" line.long 0x6C "MULTI_ERR_DATA_LOW2,LOW 32 Bits Multiple Error Read Data On OCRAM Bank2" hexmask.long 0x6C 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank2" line.long 0x70 "MULTI_ERR_DATA_HIGH2,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank2" hexmask.long 0x70 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank2" line.long 0x74 "MULTI_ERR_ADDR_ECC3,Multiple Error Address And ECC code On OCRAM Bank3" hexmask.long.tbyte 0x74 8.--26. 1. "MULTI_ERR_ADDR,Multiple Error Address On OCRAM Bank3" newline hexmask.long.byte 0x74 0.--7. 1. "MULTI_ERR_ECC,Multiple Error ECC code On OCRAM Bank3" line.long 0x78 "MULTI_ERR_DATA_LOW3,LOW 32 Bits Multiple Error Read Data On OCRAM Bank3" hexmask.long 0x78 0.--31. 1. "MULTI_ERR_DATA,LOW 32 Bits Multiple Error Read Data On OCRAM Bank3" line.long 0x7C "MULTI_ERR_DATA_HIGH3,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank3" hexmask.long 0x7C 0.--31. 1. "MULTI_ERR_DATA,HIGH 32 Bits Multiple Error Read Data On OCRAM Bank3" group.long 0x100++0x3 line.long 0x0 "PIPE_ECC_EN,OCRAM Pipeline And ECC Enable" bitfld.long 0x0 4. "ECC_EN,ECC Function Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 3. "WRITE_ADDR_PIPE_EN,Write Address Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 2. "WRITE_DATA_PIPE_EN,Write Data Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 1. "READ_ADDR_PIPE_EN,Read Address Pipeline Enable" "0: Disable.,1: Enable." newline bitfld.long 0x0 0. "READ_DATA_WAIT_EN,Read Data Wait Enable" "0: Disable.,1: Enable." rgroup.long 0x104++0x3 line.long 0x0 "PENDING_STAT,Pending Status" bitfld.long 0x0 3. "WRITE_ADDR_PIPE_PENDING,Write Address Pipeline Pending" "0: No update pending status for WRITE_ADDR_PIPE_EN.,1: When WRITE_ADDR_PIPE_EN register bit is changed.." newline bitfld.long 0x0 2. "WRITE_DATA_PIPE_PENDING,Write Data Pipeline Pending" "0: No update pending status for WRITE_DATA_PIPE_EN.,1: When WRITE_DATA_PIPE_EN register bit is changed.." newline bitfld.long 0x0 1. "READ_ADDR_PIPE_PENDING,Read Address Pipeline Pending" "0: No update pending status for READ_ADDR_PIPE_EN.,1: When READ_ADDR_PIPE_EN register bit is changed.." newline bitfld.long 0x0 0. "READ_DATA_WAIT_PENDING,Read Data Wait Pending" "0: No update pending status for READ_DATA_WAIT_EN.,1: When READ_DATA_WAIT_EN register bit is changed.." tree.end tree.end tree "MIPI_CSI2RX" base ad:0x40810000 group.long 0x100++0x7 line.long 0x0 "CFG_NUM_LANES,Lane Configuration Register" bitfld.long 0x0 0.--1. "CFG_NUM_LANES,This field is used to set the number of active lanes for receiving data." "0: 1 Lane,1: 2 Lane,?,?" line.long 0x4 "CFG_DISABLE_DATA_LANES,Disable Data Lane Register" hexmask.long.byte 0x4 0.--3. 1. "CFG_DISABLE_DATA_LANES,This field is used to disable data lanes." rgroup.long 0x108++0x7 line.long 0x0 "BIT_ERR,ECC and CRC Error Status Register" hexmask.long.word 0x0 0.--9. 1. "BIT_ERR,This field shows the error status of ECC and CRC" line.long 0x4 "IRQ_STATUS,IRQ Status Register" hexmask.long.word 0x4 0.--8. 1. "IRQ_STATUS,This field shows the IRQ status" group.long 0x110++0x3 line.long 0x0 "IRQ_MASK,IRQ Mask Setting Register" hexmask.long.word 0x0 0.--8. 1. "IRQ_MASK,This field shows the IRQ Mask setting" rgroup.long 0x114++0x17 line.long 0x0 "ULPS_STATUS,Ultra Low Power State (ULPS) Status Register" hexmask.long.word 0x0 0.--9. 1. "STATUS,This field shows the status of Rx D-PHY ULPS state" line.long 0x4 "PPI_ERRSOT_HS,ERRSot HS Status Register" hexmask.long.byte 0x4 0.--3. 1. "STATUS,This field indicates PPI ErrSotHS captured status from D-PHY" line.long 0x8 "PPI_ERRSOTSYNC_HS,ErrSotSync HS Status Register" hexmask.long.byte 0x8 0.--3. 1. "STATUS,This field indicates PPI ErrSotSync_HS captured status from D-PHY" line.long 0xC "PPI_ERRESC,ErrEsc Status Register" hexmask.long.byte 0xC 0.--3. 1. "STATUS,This field indicates PPI ErrEsc captured status from D-PHY" line.long 0x10 "PPI_ERRSYNCESC,ErrSyncEsc Status Register" hexmask.long.byte 0x10 0.--3. 1. "STATUS,This field indicates PPI ErrSyncEsc captured status from D-PHY" line.long 0x14 "PPI_ERRCONTROL,ErrControl Status Register" hexmask.long.byte 0x14 0.--3. 1. "STATUS,This field indicates PPI ErrControl captured status from D-PHY" group.long 0x12C++0x7 line.long 0x0 "CFG_DISABLE_PAYLOAD_0,Disable Payload 0 Register" bitfld.long 0x0 20. "DIS_PAYLOAD_RGB888,RGB888" "0,1" bitfld.long 0x0 19. "DIS_PAYLOAD_RGB666,RGB666" "0,1" bitfld.long 0x0 18. "DIS_PAYLOAD_RGB565,RGB565" "0,1" bitfld.long 0x0 17. "DIS_PAYLOAD_RGB555,RGB555" "0,1" newline bitfld.long 0x0 16. "DIS_PAYLOAD_RGB444,RGB444" "0,1" bitfld.long 0x0 14. "DIS_PAYLOAD_YUV422_8BIT,YUV422 8 bit" "0,1" bitfld.long 0x0 10. "DIS_PAYLOAD_YUV420,Legacy YUV 420 8 bit" "0,1" bitfld.long 0x0 2. "DIS_PAYLOAD_EMBEDDED,Embedded" "0,1" newline bitfld.long 0x0 1. "DIS_PAYLOAD_BLANK,Blank" "0,1" bitfld.long 0x0 0. "DIS_PAYLOAD_NULL,Null" "0,1" line.long 0x4 "CFG_DISABLE_PAYLOAD_1,Disable Payload 1 Register" bitfld.long 0x4 16. "DIS_PAYLOAD_UNSUPPORTED,Unsupported Data Types" "0,1" bitfld.long 0x4 7. "DIS_PAYLOAD_UDEF_37,User defined type 0x37" "0,1" bitfld.long 0x4 6. "DIS_PAYLOAD_UDEF_36,User defined type 0x36" "0,1" bitfld.long 0x4 5. "DIS_PAYLOAD_UDEF_35,User defined type 0x35" "0,1" newline bitfld.long 0x4 4. "DIS_PAYLOAD_UDEF_34,User defined type 0x35" "0,1" bitfld.long 0x4 3. "DIS_PAYLOAD_UDEF_33,User defined type 0x34" "0,1" bitfld.long 0x4 2. "DIS_PAYLOAD_UDEF_32,User defined type 0x33" "0,1" bitfld.long 0x4 1. "DIS_PAYLOAD_UDEF_31,User defined type 0x32" "0,1" newline bitfld.long 0x4 0. "DIS_PAYLOAD_UDEF_30,User defined type 0x31" "0,1" group.long 0x180++0x1B line.long 0x0 "CFG_IGNORE_VC,Ignore Virtual Channel Register" bitfld.long 0x0 0. "IGNORE_VC,When set this input causes the interface to ignore the Virtual Channel (VC) field in received packets" "0,1" line.long 0x4 "CFG_VID_VC,Virtual Channel value Register" bitfld.long 0x4 0.--1. "VID_VC,This bit field sets the Virtual Channel value the interface must match in an incoming packet for it to accept the packet" "0,1,2,3" line.long 0x8 "CFG_VID_P_FIFO_SEND_LEVEL,FIFO Send Level Configuration Register" hexmask.long.word 0x8 0.--15. 1. "SEND_LEVEL,FIFO Send Level field" line.long 0xC "CFG_VID_VSYNC,VSYNC Configuration Register" hexmask.long.byte 0xC 0.--7. 1. "WIDTH,Width of VSYNC" line.long 0x10 "CFG_VID_HSYNC_FP,Start of HSYNC Delay control Register" hexmask.long.byte 0x10 0.--7. 1. "DELAY_CTL,Delay control for beginning of HSYNC pulse" line.long 0x14 "CFG_VID_HSYNC,HSYNC Configuration Register" hexmask.long.byte 0x14 0.--7. 1. "WIDTH,Width of HSYNC" line.long 0x18 "CFG_VID_HSYNC_BP,End of HSYNC Delay Control Register" hexmask.long.byte 0x18 0.--7. 1. "DELAY_CTL,Delay Control for end of HSYNC pulse" tree.end sif (cpuis("IMXRT1163-CM4")||cpuis("IMXRT1165-CM4")||cpuis("IMXRT1166-CM4")) tree "MMCAU" base ad:0xE0081000 group.long 0x0++0x7 line.long 0x0 "CASR,Status Register" hexmask.long.byte 0x0 28.--31. 1. "VER,CAU Version" bitfld.long 0x0 1. "DPE,DES Parity Error" "0: No error detected.,1: DES key parity error detected." bitfld.long 0x0 0. "IC,Illegal Command" "0: No illegal commands issued.,1: Illegal command issued." line.long 0x4 "CAA,Accumulator" hexmask.long 0x4 0.--31. 1. "ACC,Accumulator" repeat 9. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x8)++0x3 line.long 0x0 "CA[$1],General Purpose Register" hexmask.long 0x0 0.--31. 1. "CAn,General Purpose Registers" repeat.end tree.end endif tree "MU" base ad:0x0 sif (cpuis("IMXRT1165-CM7")) tree "MUA" base ad:0x40C48000 group.long 0x0++0xF line.long 0x0 "TR0,Processor A Transmit Register 0" hexmask.long 0x0 0.--31. 1. "DATA,TR0" line.long 0x4 "TR1,Processor A Transmit Register 1" hexmask.long 0x4 0.--31. 1. "DATA,TR1" line.long 0x8 "TR2,Processor A Transmit Register 2" hexmask.long 0x8 0.--31. 1. "DATA,TR2" line.long 0xC "TR3,Processor A Transmit Register 3" hexmask.long 0xC 0.--31. 1. "DATA,TR3" rgroup.long 0x10++0xF line.long 0x0 "RR0,Processor A Receive Register 0" hexmask.long 0x0 0.--31. 1. "DATA,RR0" line.long 0x4 "RR1,Processor A Receive Register 1" hexmask.long 0x4 0.--31. 1. "DATA,RR1" line.long 0x8 "RR2,Processor A Receive Register 2" hexmask.long 0x8 0.--31. 1. "DATA,RR2" line.long 0xC "RR3,Processor A Receive Register 3" hexmask.long 0xC 0.--31. 1. "DATA,RR3" group.long 0x20++0x7 line.long 0x0 "SR,Processor A Status Register" hexmask.long.byte 0x0 28.--31. 1. "GIPn,GIPn" hexmask.long.byte 0x0 24.--27. 1. "RFn,RFn" newline hexmask.long.byte 0x0 20.--23. 1. "TEn,TEn" rbitfld.long 0x0 8. "FUP,FUP" "0: No flags updated initiated by the Processor A in..,1: Processor A initiated flags update processing" newline rbitfld.long 0x0 7. "RS,RS" "0: The Processor B-side of the MU is not in reset.,1: The Processor B-side of the MU is in reset." rbitfld.long 0x0 4. "EP,EP" "0: The Processor A-side event is not pending..,1: The Processor A-side event is pending." newline rbitfld.long 0x0 0.--2. "Fn,Fn" "0: BAFn bit in MUB.CR register is written 0..,1: BAFn bit in MUB.CR register is written 1.,?,?,?,?,?,?" line.long 0x4 "CR,Processor A Control Register" hexmask.long.byte 0x4 28.--31. 1. "GIEn,GIEn" hexmask.long.byte 0x4 24.--27. 1. "RIEn,RIEn" newline hexmask.long.byte 0x4 20.--23. 1. "TIEn,TIEn" hexmask.long.byte 0x4 16.--19. 1. "GIRn,GIRn" newline bitfld.long 0x4 5. "MUR,MUR" "0: N/A. Self clearing bit (default).,1: Asserts the Processor A MU reset." bitfld.long 0x4 0.--2. "Fn,Fn" "0: N/A. Self clearing bit (default).,1: Asserts the Processor A MU reset.,?,?,?,?,?,?" tree.end endif sif (cpuis("IMXRT1165-CM4")) tree "MUB" base ad:0x40C4C000 group.long 0x0++0xF line.long 0x0 "TR0,Processor B Transmit Register 0" hexmask.long 0x0 0.--31. 1. "DATA,TR0" line.long 0x4 "TR1,Processor B Transmit Register 1" hexmask.long 0x4 0.--31. 1. "DATA,TR1" line.long 0x8 "TR2,Processor B Transmit Register 2" hexmask.long 0x8 0.--31. 1. "DATA,TR2" line.long 0xC "TR3,Processor B Transmit Register 3" hexmask.long 0xC 0.--31. 1. "DATA,TR3" rgroup.long 0x10++0xF line.long 0x0 "RR0,Processor B Receive Register 0" hexmask.long 0x0 0.--31. 1. "DATA,RR0" line.long 0x4 "RR1,Processor B Receive Register 1" hexmask.long 0x4 0.--31. 1. "DATA,RR1" line.long 0x8 "RR2,Processor B Receive Register 2" hexmask.long 0x8 0.--31. 1. "DATA,RR2" line.long 0xC "RR3,Processor B Receive Register 3" hexmask.long 0xC 0.--31. 1. "DATA,RR3" group.long 0x20++0x7 line.long 0x0 "SR,Processor B Status Register" hexmask.long.byte 0x0 28.--31. 1. "GIPn,GIPn" hexmask.long.byte 0x0 24.--27. 1. "RFn,RFn" newline hexmask.long.byte 0x0 20.--23. 1. "TEn,TEn" rbitfld.long 0x0 8. "FUP,FUP" "0: No flags updated initiated by the Processor B in..,1: Processor B initiated flags update processing" newline rbitfld.long 0x0 7. "RS,RS" "0: The Processor A or the Processor A-side of the..,1: The Processor A or the Processor A-side of the.." rbitfld.long 0x0 4. "EP,EP" "0: The Processor B-side event is not pending..,1: The Processor B-side event is pending." newline rbitfld.long 0x0 0.--2. "Fn,Fn" "0: ABFn bit in MUA.CR register is written 0..,1: ABFn bit in MUA.CR register is written 1.,?,?,?,?,?,?" line.long 0x4 "CR,Processor B Control Register" hexmask.long.byte 0x4 28.--31. 1. "GIEn,GIEn" hexmask.long.byte 0x4 24.--27. 1. "RIEn,RIEn" newline hexmask.long.byte 0x4 20.--23. 1. "TIEn,TIEn" hexmask.long.byte 0x4 16.--19. 1. "GIRn,GIRn" newline bitfld.long 0x4 0.--2. "Fn,Fn" "0: Clears the Fn bit in the MUA.SR register.,1: Sets the Fn bit in the MUA.SR register.,?,?,?,?,?,?" tree.end endif sif (cpuis("IMXRT1166-CM4")) tree "MUB" base ad:0x40C4C000 group.long 0x0++0xF line.long 0x0 "TR0,Processor B Transmit Register 0" hexmask.long 0x0 0.--31. 1. "DATA,TR0" line.long 0x4 "TR1,Processor B Transmit Register 1" hexmask.long 0x4 0.--31. 1. "DATA,TR1" line.long 0x8 "TR2,Processor B Transmit Register 2" hexmask.long 0x8 0.--31. 1. "DATA,TR2" line.long 0xC "TR3,Processor B Transmit Register 3" hexmask.long 0xC 0.--31. 1. "DATA,TR3" rgroup.long 0x10++0xF line.long 0x0 "RR0,Processor B Receive Register 0" hexmask.long 0x0 0.--31. 1. "DATA,RR0" line.long 0x4 "RR1,Processor B Receive Register 1" hexmask.long 0x4 0.--31. 1. "DATA,RR1" line.long 0x8 "RR2,Processor B Receive Register 2" hexmask.long 0x8 0.--31. 1. "DATA,RR2" line.long 0xC "RR3,Processor B Receive Register 3" hexmask.long 0xC 0.--31. 1. "DATA,RR3" group.long 0x20++0x7 line.long 0x0 "SR,Processor B Status Register" hexmask.long.byte 0x0 28.--31. 1. "GIPn,GIPn" hexmask.long.byte 0x0 24.--27. 1. "RFn,RFn" newline hexmask.long.byte 0x0 20.--23. 1. "TEn,TEn" rbitfld.long 0x0 8. "FUP,FUP" "0: No flags updated initiated by the Processor B in..,1: Processor B initiated flags update processing" newline rbitfld.long 0x0 7. "RS,RS" "0: The Processor A or the Processor A-side of the..,1: The Processor A or the Processor A-side of the.." rbitfld.long 0x0 4. "EP,EP" "0: The Processor B-side event is not pending..,1: The Processor B-side event is pending." newline rbitfld.long 0x0 0.--2. "Fn,Fn" "0: ABFn bit in MUA.CR register is written 0..,1: ABFn bit in MUA.CR register is written 1.,?,?,?,?,?,?" line.long 0x4 "CR,Processor B Control Register" hexmask.long.byte 0x4 28.--31. 1. "GIEn,GIEn" hexmask.long.byte 0x4 24.--27. 1. "RIEn,RIEn" newline hexmask.long.byte 0x4 20.--23. 1. "TIEn,TIEn" hexmask.long.byte 0x4 16.--19. 1. "GIRn,GIRn" newline bitfld.long 0x4 0.--2. "Fn,Fn" "0: Clears the Fn bit in the MUA.SR register.,1: Sets the Fn bit in the MUA.SR register.,?,?,?,?,?,?" tree.end endif sif (cpuis("IMXRT1166-CM7")) tree "MUA" base ad:0x40C48000 group.long 0x0++0xF line.long 0x0 "TR0,Processor A Transmit Register 0" hexmask.long 0x0 0.--31. 1. "DATA,TR0" line.long 0x4 "TR1,Processor A Transmit Register 1" hexmask.long 0x4 0.--31. 1. "DATA,TR1" line.long 0x8 "TR2,Processor A Transmit Register 2" hexmask.long 0x8 0.--31. 1. "DATA,TR2" line.long 0xC "TR3,Processor A Transmit Register 3" hexmask.long 0xC 0.--31. 1. "DATA,TR3" rgroup.long 0x10++0xF line.long 0x0 "RR0,Processor A Receive Register 0" hexmask.long 0x0 0.--31. 1. "DATA,RR0" line.long 0x4 "RR1,Processor A Receive Register 1" hexmask.long 0x4 0.--31. 1. "DATA,RR1" line.long 0x8 "RR2,Processor A Receive Register 2" hexmask.long 0x8 0.--31. 1. "DATA,RR2" line.long 0xC "RR3,Processor A Receive Register 3" hexmask.long 0xC 0.--31. 1. "DATA,RR3" group.long 0x20++0x7 line.long 0x0 "SR,Processor A Status Register" hexmask.long.byte 0x0 28.--31. 1. "GIPn,GIPn" hexmask.long.byte 0x0 24.--27. 1. "RFn,RFn" newline hexmask.long.byte 0x0 20.--23. 1. "TEn,TEn" rbitfld.long 0x0 8. "FUP,FUP" "0: No flags updated initiated by the Processor A in..,1: Processor A initiated flags update processing" newline rbitfld.long 0x0 7. "RS,RS" "0: The Processor B-side of the MU is not in reset.,1: The Processor B-side of the MU is in reset." rbitfld.long 0x0 4. "EP,EP" "0: The Processor A-side event is not pending..,1: The Processor A-side event is pending." newline rbitfld.long 0x0 0.--2. "Fn,Fn" "0: BAFn bit in MUB.CR register is written 0..,1: BAFn bit in MUB.CR register is written 1.,?,?,?,?,?,?" line.long 0x4 "CR,Processor A Control Register" hexmask.long.byte 0x4 28.--31. 1. "GIEn,GIEn" hexmask.long.byte 0x4 24.--27. 1. "RIEn,RIEn" newline hexmask.long.byte 0x4 20.--23. 1. "TIEn,TIEn" hexmask.long.byte 0x4 16.--19. 1. "GIRn,GIRn" newline bitfld.long 0x4 5. "MUR,MUR" "0: N/A. Self clearing bit (default).,1: Asserts the Processor A MU reset." bitfld.long 0x4 0.--2. "Fn,Fn" "0: N/A. Self clearing bit (default).,1: Asserts the Processor A MU reset.,?,?,?,?,?,?" tree.end endif tree.end tree "NVIC" base ad:0xE000E100 group.long 0x0++0xF line.long 0x0 "NVICISER0,Interrupt Set Enable Register n" hexmask.long 0x0 0.--31. 1. "SETENA,Interrupt set enable bits" line.long 0x4 "NVICISER1,Interrupt Set Enable Register n" hexmask.long 0x4 0.--31. 1. "SETENA,Interrupt set enable bits" line.long 0x8 "NVICISER2,Interrupt Set Enable Register n" hexmask.long 0x8 0.--31. 1. "SETENA,Interrupt set enable bits" line.long 0xC "NVICISER3,Interrupt Set Enable Register n" hexmask.long 0xC 0.--31. 1. "SETENA,Interrupt set enable bits" group.long 0x80++0xF line.long 0x0 "NVICICER0,Interrupt Clear Enable Register n" hexmask.long 0x0 0.--31. 1. "CLRENA,Interrupt clear-enable bits" line.long 0x4 "NVICICER1,Interrupt Clear Enable Register n" hexmask.long 0x4 0.--31. 1. "CLRENA,Interrupt clear-enable bits" line.long 0x8 "NVICICER2,Interrupt Clear Enable Register n" hexmask.long 0x8 0.--31. 1. "CLRENA,Interrupt clear-enable bits" line.long 0xC "NVICICER3,Interrupt Clear Enable Register n" hexmask.long 0xC 0.--31. 1. "CLRENA,Interrupt clear-enable bits" group.long 0x100++0xF line.long 0x0 "NVICISPR0,Interrupt Set Pending Register n" hexmask.long 0x0 0.--31. 1. "SETPEND,Interrupt set-pending bits" line.long 0x4 "NVICISPR1,Interrupt Set Pending Register n" hexmask.long 0x4 0.--31. 1. "SETPEND,Interrupt set-pending bits" line.long 0x8 "NVICISPR2,Interrupt Set Pending Register n" hexmask.long 0x8 0.--31. 1. "SETPEND,Interrupt set-pending bits" line.long 0xC "NVICISPR3,Interrupt Set Pending Register n" hexmask.long 0xC 0.--31. 1. "SETPEND,Interrupt set-pending bits" group.long 0x180++0xF line.long 0x0 "NVICICPR0,Interrupt Clear Pending Register n" hexmask.long 0x0 0.--31. 1. "CLRPEND,Interrupt clear-pending bits" line.long 0x4 "NVICICPR1,Interrupt Clear Pending Register n" hexmask.long 0x4 0.--31. 1. "CLRPEND,Interrupt clear-pending bits" line.long 0x8 "NVICICPR2,Interrupt Clear Pending Register n" hexmask.long 0x8 0.--31. 1. "CLRPEND,Interrupt clear-pending bits" line.long 0xC "NVICICPR3,Interrupt Clear Pending Register n" hexmask.long 0xC 0.--31. 1. "CLRPEND,Interrupt clear-pending bits" group.long 0x200++0xF line.long 0x0 "NVICIABR0,Interrupt Active bit Register n" hexmask.long 0x0 0.--31. 1. "ACTIVE,Interrupt active flags" line.long 0x4 "NVICIABR1,Interrupt Active bit Register n" hexmask.long 0x4 0.--31. 1. "ACTIVE,Interrupt active flags" line.long 0x8 "NVICIABR2,Interrupt Active bit Register n" hexmask.long 0x8 0.--31. 1. "ACTIVE,Interrupt active flags" line.long 0xC "NVICIABR3,Interrupt Active bit Register n" hexmask.long 0xC 0.--31. 1. "ACTIVE,Interrupt active flags" group.byte 0x300++0x69 line.byte 0x0 "NVICIP0,Interrupt Priority Register 0" hexmask.byte 0x0 4.--7. 1. "PRI0,Priority of interrupt 0" line.byte 0x1 "NVICIP1,Interrupt Priority Register 1" hexmask.byte 0x1 4.--7. 1. "PRI1,Priority of interrupt 1" line.byte 0x2 "NVICIP2,Interrupt Priority Register 2" hexmask.byte 0x2 4.--7. 1. "PRI2,Priority of interrupt 2" line.byte 0x3 "NVICIP3,Interrupt Priority Register 3" hexmask.byte 0x3 4.--7. 1. "PRI3,Priority of interrupt 3" line.byte 0x4 "NVICIP4,Interrupt Priority Register 4" hexmask.byte 0x4 4.--7. 1. "PRI4,Priority of interrupt 4" line.byte 0x5 "NVICIP5,Interrupt Priority Register 5" hexmask.byte 0x5 4.--7. 1. "PRI5,Priority of interrupt 5" line.byte 0x6 "NVICIP6,Interrupt Priority Register 6" hexmask.byte 0x6 4.--7. 1. "PRI6,Priority of interrupt 6" line.byte 0x7 "NVICIP7,Interrupt Priority Register 7" hexmask.byte 0x7 4.--7. 1. "PRI7,Priority of interrupt 7" line.byte 0x8 "NVICIP8,Interrupt Priority Register 8" hexmask.byte 0x8 4.--7. 1. "PRI8,Priority of interrupt 8" line.byte 0x9 "NVICIP9,Interrupt Priority Register 9" hexmask.byte 0x9 4.--7. 1. "PRI9,Priority of interrupt 9" line.byte 0xA "NVICIP10,Interrupt Priority Register 10" hexmask.byte 0xA 4.--7. 1. "PRI10,Priority of interrupt 10" line.byte 0xB "NVICIP11,Interrupt Priority Register 11" hexmask.byte 0xB 4.--7. 1. "PRI11,Priority of interrupt 11" line.byte 0xC "NVICIP12,Interrupt Priority Register 12" hexmask.byte 0xC 4.--7. 1. "PRI12,Priority of interrupt 12" line.byte 0xD "NVICIP13,Interrupt Priority Register 13" hexmask.byte 0xD 4.--7. 1. "PRI13,Priority of interrupt 13" line.byte 0xE "NVICIP14,Interrupt Priority Register 14" hexmask.byte 0xE 4.--7. 1. "PRI14,Priority of interrupt 14" line.byte 0xF "NVICIP15,Interrupt Priority Register 15" hexmask.byte 0xF 4.--7. 1. "PRI15,Priority of interrupt 15" line.byte 0x10 "NVICIP16,Interrupt Priority Register 16" hexmask.byte 0x10 4.--7. 1. "PRI16,Priority of interrupt 16" line.byte 0x11 "NVICIP17,Interrupt Priority Register 17" hexmask.byte 0x11 4.--7. 1. "PRI17,Priority of interrupt 17" line.byte 0x12 "NVICIP18,Interrupt Priority Register 18" hexmask.byte 0x12 4.--7. 1. "PRI18,Priority of interrupt 18" line.byte 0x13 "NVICIP19,Interrupt Priority Register 19" hexmask.byte 0x13 4.--7. 1. "PRI19,Priority of interrupt 19" line.byte 0x14 "NVICIP20,Interrupt Priority Register 20" hexmask.byte 0x14 4.--7. 1. "PRI20,Priority of interrupt 20" line.byte 0x15 "NVICIP21,Interrupt Priority Register 21" hexmask.byte 0x15 4.--7. 1. "PRI21,Priority of interrupt 21" line.byte 0x16 "NVICIP22,Interrupt Priority Register 22" hexmask.byte 0x16 4.--7. 1. "PRI22,Priority of interrupt 22" line.byte 0x17 "NVICIP23,Interrupt Priority Register 23" hexmask.byte 0x17 4.--7. 1. "PRI23,Priority of interrupt 23" line.byte 0x18 "NVICIP24,Interrupt Priority Register 24" hexmask.byte 0x18 4.--7. 1. "PRI24,Priority of interrupt 24" line.byte 0x19 "NVICIP25,Interrupt Priority Register 25" hexmask.byte 0x19 4.--7. 1. "PRI25,Priority of interrupt 25" line.byte 0x1A "NVICIP26,Interrupt Priority Register 26" hexmask.byte 0x1A 4.--7. 1. "PRI26,Priority of interrupt 26" line.byte 0x1B "NVICIP27,Interrupt Priority Register 27" hexmask.byte 0x1B 4.--7. 1. "PRI27,Priority of interrupt 27" line.byte 0x1C "NVICIP28,Interrupt Priority Register 28" hexmask.byte 0x1C 4.--7. 1. "PRI28,Priority of interrupt 28" line.byte 0x1D "NVICIP29,Interrupt Priority Register 29" hexmask.byte 0x1D 4.--7. 1. "PRI29,Priority of interrupt 29" line.byte 0x1E "NVICIP30,Interrupt Priority Register 30" hexmask.byte 0x1E 4.--7. 1. "PRI30,Priority of interrupt 30" line.byte 0x1F "NVICIP31,Interrupt Priority Register 31" hexmask.byte 0x1F 4.--7. 1. "PRI31,Priority of interrupt 31" line.byte 0x20 "NVICIP32,Interrupt Priority Register 32" hexmask.byte 0x20 4.--7. 1. "PRI32,Priority of interrupt 32" line.byte 0x21 "NVICIP33,Interrupt Priority Register 33" hexmask.byte 0x21 4.--7. 1. "PRI33,Priority of interrupt 33" line.byte 0x22 "NVICIP34,Interrupt Priority Register 34" hexmask.byte 0x22 4.--7. 1. "PRI34,Priority of interrupt 34" line.byte 0x23 "NVICIP35,Interrupt Priority Register 35" hexmask.byte 0x23 4.--7. 1. "PRI35,Priority of interrupt 35" line.byte 0x24 "NVICIP36,Interrupt Priority Register 36" hexmask.byte 0x24 4.--7. 1. "PRI36,Priority of interrupt 36" line.byte 0x25 "NVICIP37,Interrupt Priority Register 37" hexmask.byte 0x25 4.--7. 1. "PRI37,Priority of interrupt 37" line.byte 0x26 "NVICIP38,Interrupt Priority Register 38" hexmask.byte 0x26 4.--7. 1. "PRI38,Priority of interrupt 38" line.byte 0x27 "NVICIP39,Interrupt Priority Register 39" hexmask.byte 0x27 4.--7. 1. "PRI39,Priority of interrupt 39" line.byte 0x28 "NVICIP40,Interrupt Priority Register 40" hexmask.byte 0x28 4.--7. 1. "PRI40,Priority of interrupt 40" line.byte 0x29 "NVICIP41,Interrupt Priority Register 41" hexmask.byte 0x29 4.--7. 1. "PRI41,Priority of interrupt 41" line.byte 0x2A "NVICIP42,Interrupt Priority Register 42" hexmask.byte 0x2A 4.--7. 1. "PRI42,Priority of interrupt 42" line.byte 0x2B "NVICIP43,Interrupt Priority Register 43" hexmask.byte 0x2B 4.--7. 1. "PRI43,Priority of interrupt 43" line.byte 0x2C "NVICIP44,Interrupt Priority Register 44" hexmask.byte 0x2C 4.--7. 1. "PRI44,Priority of interrupt 44" line.byte 0x2D "NVICIP45,Interrupt Priority Register 45" hexmask.byte 0x2D 4.--7. 1. "PRI45,Priority of interrupt 45" line.byte 0x2E "NVICIP46,Interrupt Priority Register 46" hexmask.byte 0x2E 4.--7. 1. "PRI46,Priority of interrupt 46" line.byte 0x2F "NVICIP47,Interrupt Priority Register 47" hexmask.byte 0x2F 4.--7. 1. "PRI47,Priority of interrupt 47" line.byte 0x30 "NVICIP48,Interrupt Priority Register 48" hexmask.byte 0x30 4.--7. 1. "PRI48,Priority of interrupt 48" line.byte 0x31 "NVICIP49,Interrupt Priority Register 49" hexmask.byte 0x31 4.--7. 1. "PRI49,Priority of interrupt 49" line.byte 0x32 "NVICIP50,Interrupt Priority Register 50" hexmask.byte 0x32 4.--7. 1. "PRI50,Priority of interrupt 50" line.byte 0x33 "NVICIP51,Interrupt Priority Register 51" hexmask.byte 0x33 4.--7. 1. "PRI51,Priority of interrupt 51" line.byte 0x34 "NVICIP52,Interrupt Priority Register 52" hexmask.byte 0x34 4.--7. 1. "PRI52,Priority of interrupt 52" line.byte 0x35 "NVICIP53,Interrupt Priority Register 53" hexmask.byte 0x35 4.--7. 1. "PRI53,Priority of interrupt 53" line.byte 0x36 "NVICIP54,Interrupt Priority Register 54" hexmask.byte 0x36 4.--7. 1. "PRI54,Priority of interrupt 54" line.byte 0x37 "NVICIP55,Interrupt Priority Register 55" hexmask.byte 0x37 4.--7. 1. "PRI55,Priority of interrupt 55" line.byte 0x38 "NVICIP56,Interrupt Priority Register 56" hexmask.byte 0x38 4.--7. 1. "PRI56,Priority of interrupt 56" line.byte 0x39 "NVICIP57,Interrupt Priority Register 57" hexmask.byte 0x39 4.--7. 1. "PRI57,Priority of interrupt 57" line.byte 0x3A "NVICIP58,Interrupt Priority Register 58" hexmask.byte 0x3A 4.--7. 1. "PRI58,Priority of interrupt 58" line.byte 0x3B "NVICIP59,Interrupt Priority Register 59" hexmask.byte 0x3B 4.--7. 1. "PRI59,Priority of interrupt 59" line.byte 0x3C "NVICIP60,Interrupt Priority Register 60" hexmask.byte 0x3C 4.--7. 1. "PRI60,Priority of interrupt 60" line.byte 0x3D "NVICIP61,Interrupt Priority Register 61" hexmask.byte 0x3D 4.--7. 1. "PRI61,Priority of interrupt 61" line.byte 0x3E "NVICIP62,Interrupt Priority Register 62" hexmask.byte 0x3E 4.--7. 1. "PRI62,Priority of interrupt 62" line.byte 0x3F "NVICIP63,Interrupt Priority Register 63" hexmask.byte 0x3F 4.--7. 1. "PRI63,Priority of interrupt 63" line.byte 0x40 "NVICIP64,Interrupt Priority Register 64" hexmask.byte 0x40 4.--7. 1. "PRI64,Priority of interrupt 64" line.byte 0x41 "NVICIP65,Interrupt Priority Register 65" hexmask.byte 0x41 4.--7. 1. "PRI65,Priority of interrupt 65" line.byte 0x42 "NVICIP66,Interrupt Priority Register 66" hexmask.byte 0x42 4.--7. 1. "PRI66,Priority of interrupt 66" line.byte 0x43 "NVICIP67,Interrupt Priority Register 67" hexmask.byte 0x43 4.--7. 1. "PRI67,Priority of interrupt 67" line.byte 0x44 "NVICIP68,Interrupt Priority Register 68" hexmask.byte 0x44 4.--7. 1. "PRI68,Priority of interrupt 68" line.byte 0x45 "NVICIP69,Interrupt Priority Register 69" hexmask.byte 0x45 4.--7. 1. "PRI69,Priority of interrupt 69" line.byte 0x46 "NVICIP70,Interrupt Priority Register 70" hexmask.byte 0x46 4.--7. 1. "PRI70,Priority of interrupt 70" line.byte 0x47 "NVICIP71,Interrupt Priority Register 71" hexmask.byte 0x47 4.--7. 1. "PRI71,Priority of interrupt 71" line.byte 0x48 "NVICIP72,Interrupt Priority Register 72" hexmask.byte 0x48 4.--7. 1. "PRI72,Priority of interrupt 72" line.byte 0x49 "NVICIP73,Interrupt Priority Register 73" hexmask.byte 0x49 4.--7. 1. "PRI73,Priority of interrupt 73" line.byte 0x4A "NVICIP74,Interrupt Priority Register 74" hexmask.byte 0x4A 4.--7. 1. "PRI74,Priority of interrupt 74" line.byte 0x4B "NVICIP75,Interrupt Priority Register 75" hexmask.byte 0x4B 4.--7. 1. "PRI75,Priority of interrupt 75" line.byte 0x4C "NVICIP76,Interrupt Priority Register 76" hexmask.byte 0x4C 4.--7. 1. "PRI76,Priority of interrupt 76" line.byte 0x4D "NVICIP77,Interrupt Priority Register 77" hexmask.byte 0x4D 4.--7. 1. "PRI77,Priority of interrupt 77" line.byte 0x4E "NVICIP78,Interrupt Priority Register 78" hexmask.byte 0x4E 4.--7. 1. "PRI78,Priority of interrupt 78" line.byte 0x4F "NVICIP79,Interrupt Priority Register 79" hexmask.byte 0x4F 4.--7. 1. "PRI79,Priority of interrupt 79" line.byte 0x50 "NVICIP80,Interrupt Priority Register 80" hexmask.byte 0x50 4.--7. 1. "PRI80,Priority of interrupt 80" line.byte 0x51 "NVICIP81,Interrupt Priority Register 81" hexmask.byte 0x51 4.--7. 1. "PRI81,Priority of interrupt 81" line.byte 0x52 "NVICIP82,Interrupt Priority Register 82" hexmask.byte 0x52 4.--7. 1. "PRI82,Priority of interrupt 82" line.byte 0x53 "NVICIP83,Interrupt Priority Register 83" hexmask.byte 0x53 4.--7. 1. "PRI83,Priority of interrupt 83" line.byte 0x54 "NVICIP84,Interrupt Priority Register 84" hexmask.byte 0x54 4.--7. 1. "PRI84,Priority of interrupt 84" line.byte 0x55 "NVICIP85,Interrupt Priority Register 85" hexmask.byte 0x55 4.--7. 1. "PRI85,Priority of interrupt 85" line.byte 0x56 "NVICIP86,Interrupt Priority Register 86" hexmask.byte 0x56 4.--7. 1. "PRI86,Priority of interrupt 86" line.byte 0x57 "NVICIP87,Interrupt Priority Register 87" hexmask.byte 0x57 4.--7. 1. "PRI87,Priority of interrupt 87" line.byte 0x58 "NVICIP88,Interrupt Priority Register 88" hexmask.byte 0x58 4.--7. 1. "PRI88,Priority of interrupt 88" line.byte 0x59 "NVICIP89,Interrupt Priority Register 89" hexmask.byte 0x59 4.--7. 1. "PRI89,Priority of interrupt 89" line.byte 0x5A "NVICIP90,Interrupt Priority Register 90" hexmask.byte 0x5A 4.--7. 1. "PRI90,Priority of interrupt 90" line.byte 0x5B "NVICIP91,Interrupt Priority Register 91" hexmask.byte 0x5B 4.--7. 1. "PRI91,Priority of interrupt 91" line.byte 0x5C "NVICIP92,Interrupt Priority Register 92" hexmask.byte 0x5C 4.--7. 1. "PRI92,Priority of interrupt 92" line.byte 0x5D "NVICIP93,Interrupt Priority Register 93" hexmask.byte 0x5D 4.--7. 1. "PRI93,Priority of interrupt 93" line.byte 0x5E "NVICIP94,Interrupt Priority Register 94" hexmask.byte 0x5E 4.--7. 1. "PRI94,Priority of interrupt 94" line.byte 0x5F "NVICIP95,Interrupt Priority Register 95" hexmask.byte 0x5F 4.--7. 1. "PRI95,Priority of interrupt 95" line.byte 0x60 "NVICIP96,Interrupt Priority Register 96" hexmask.byte 0x60 4.--7. 1. "PRI96,Priority of interrupt 96" line.byte 0x61 "NVICIP97,Interrupt Priority Register 97" hexmask.byte 0x61 4.--7. 1. "PRI97,Priority of interrupt 97" line.byte 0x62 "NVICIP98,Interrupt Priority Register 98" hexmask.byte 0x62 4.--7. 1. "PRI98,Priority of interrupt 98" line.byte 0x63 "NVICIP99,Interrupt Priority Register 99" hexmask.byte 0x63 4.--7. 1. "PRI99,Priority of interrupt 99" line.byte 0x64 "NVICIP100,Interrupt Priority Register 100" hexmask.byte 0x64 4.--7. 1. "PRI100,Priority of interrupt 100" line.byte 0x65 "NVICIP101,Interrupt Priority Register 101" hexmask.byte 0x65 4.--7. 1. "PRI101,Priority of interrupt 101" line.byte 0x66 "NVICIP102,Interrupt Priority Register 102" hexmask.byte 0x66 4.--7. 1. "PRI102,Priority of interrupt 102" line.byte 0x67 "NVICIP103,Interrupt Priority Register 103" hexmask.byte 0x67 4.--7. 1. "PRI103,Priority of interrupt 103" line.byte 0x68 "NVICIP104,Interrupt Priority Register 104" hexmask.byte 0x68 4.--7. 1. "PRI104,Priority of interrupt 104" line.byte 0x69 "NVICIP105,Interrupt Priority Register 105" hexmask.byte 0x69 4.--7. 1. "PRI105,Priority of interrupt 105" group.long 0xE00++0x3 line.long 0x0 "NVICSTIR,Software Trigger Interrupt Register" hexmask.long.word 0x0 0.--8. 1. "INTID,Interrupt ID of the interrupt to trigger in the range 0-239. For example a value of 0x03 specifies interrupt IRQ3." tree.end tree "OCOTP" base ad:0x40CAC000 group.long 0x0++0x13 line.long 0x0 "CTRL,OTP Controller Control and Status Register" hexmask.long.word 0x0 16.--31. 1. "WR_UNLOCK,Write unlock" newline bitfld.long 0x0 15. "WORDLOCK,Lock fuse word" "0: No change to LOCK bit when programming a word..,1: LOCK bit for fuse word will be set after.." newline bitfld.long 0x0 12. "RELOAD_SHADOWS,Reload Shadow Registers" "0: Do not force shadow register re-load.,1: Force shadow register re-load. This bit is.." newline bitfld.long 0x0 11. "ERROR,Locked Region Access Error" "0: No error.,1: Error - access to a locked region requested." newline rbitfld.long 0x0 10. "BUSY,OTP controller status bit" "0: No write or read access to OTP started.,1: Write or read access to OTP started." newline hexmask.long.word 0x0 0.--9. 1. "ADDR,OTP write and read access address register" line.long 0x4 "CTRL_SET,OTP Controller Control and Status Register" hexmask.long.word 0x4 16.--31. 1. "WR_UNLOCK,Write unlock" newline bitfld.long 0x4 15. "WORDLOCK,Lock fuse word" "0,1" newline bitfld.long 0x4 12. "RELOAD_SHADOWS,Reload Shadow Registers" "0,1" newline bitfld.long 0x4 11. "ERROR,Locked Region Access Error" "0,1" newline rbitfld.long 0x4 10. "BUSY,OTP controller status bit" "0,1" newline hexmask.long.word 0x4 0.--9. 1. "ADDR,OTP write and read access address register" line.long 0x8 "CTRL_CLR,OTP Controller Control and Status Register" hexmask.long.word 0x8 16.--31. 1. "WR_UNLOCK,Write unlock" newline eventfld.long 0x8 15. "WORDLOCK,Lock fuse word" "0,1" newline eventfld.long 0x8 12. "RELOAD_SHADOWS,Reload Shadow Registers" "0,1" newline eventfld.long 0x8 11. "ERROR,Locked Region Access Error" "0,1" newline eventfld.long 0x8 10. "BUSY,OTP controller status bit" "0,1" newline hexmask.long.word 0x8 0.--9. 1. "ADDR,OTP write and read access address register" line.long 0xC "CTRL_TOG,OTP Controller Control and Status Register" hexmask.long.word 0xC 16.--31. 1. "WR_UNLOCK,Write unlock" newline bitfld.long 0xC 15. "WORDLOCK,Lock fuse word" "0,1" newline bitfld.long 0xC 12. "RELOAD_SHADOWS,Reload Shadow Registers" "0,1" newline bitfld.long 0xC 11. "ERROR,Locked Region Access Error" "0,1" newline rbitfld.long 0xC 10. "BUSY,OTP controller status bit" "0,1" newline hexmask.long.word 0xC 0.--9. 1. "ADDR,OTP write and read access address register" line.long 0x10 "PDN,OTP Controller PDN Register" eventfld.long 0x10 0. "PDN,PDN value" "0: OTP memory is not powered,1: OTP memory is powered" group.long 0x20++0x3 line.long 0x0 "DATA,OTP Controller Write Data Register" hexmask.long 0x0 0.--31. 1. "DATA,Data" group.long 0x30++0x3 line.long 0x0 "READ_CTRL,OTP Controller Read Control Register" bitfld.long 0x0 4. "READ_FUSE_ERROR_INTR_ENA,Enable read-error interrupt" "0: Disable,1: Enable" newline bitfld.long 0x0 3. "READ_FUSE_DONE_INTR_ENA,Enable read-done interrupt" "0: Disable,1: Enable" newline bitfld.long 0x0 1.--2. "READ_FUSE_CNTR,Number of words to read." "0: 1 word,1: 2 words,2: 3 words,3: 4 words" newline bitfld.long 0x0 0. "READ_FUSE,Read Fuse" "0: Do not initiate a read from OTP,1: Initiate a read from OTP" group.long 0x90++0xF line.long 0x0 "OUT_STATUS,8K OTP Memory STATUS Register" bitfld.long 0x0 27. "DED3,Double error detect" "0,1" newline bitfld.long 0x0 26. "DED2,Double error detect" "0,1" newline bitfld.long 0x0 25. "DED1,Double error detect" "0,1" newline bitfld.long 0x0 24. "DED0,Double error detect" "0,1" newline bitfld.long 0x0 23. "READ_ERROR_INTR,Fuse read error" "0: Read operation finished with out any error,1: Read operation finished with an error" newline bitfld.long 0x0 22. "READ_DONE_INTR,Read fuse done" "0,1" newline rbitfld.long 0x0 21. "CALIBRATED,Calibrated status" "0,1" newline bitfld.long 0x0 20. "DED_RELOAD,Indicates double error detection occured on reload" "0,1" newline bitfld.long 0x0 19. "SEC_RELOAD,Indicates single error correction occured on reload" "0,1" newline hexmask.long.byte 0x0 15.--18. 1. "FLAGSTATE,Flag state" newline rbitfld.long 0x0 14. "PWOK,Power OK" "0,1" newline rbitfld.long 0x0 13. "ACK,Acknowledge" "0,1" newline bitfld.long 0x0 12. "PROGFAIL,Programming failed" "0,1" newline bitfld.long 0x0 11. "LOCKED,Word Locked" "0,1" newline bitfld.long 0x0 10. "DED,Double error detect" "0,1" newline bitfld.long 0x0 9. "SEC,Single Error Correct" "0,1" line.long 0x4 "OUT_STATUS_SET,8K OTP Memory STATUS Register" bitfld.long 0x4 27. "DED3,Double error detect" "0,1" newline bitfld.long 0x4 26. "DED2,Double error detect" "0,1" newline bitfld.long 0x4 25. "DED1,Double error detect" "0,1" newline bitfld.long 0x4 24. "DED0,Double error detect" "0,1" newline bitfld.long 0x4 23. "READ_ERROR_INTR,Fuse read error" "0,1" newline bitfld.long 0x4 22. "READ_DONE_INTR,Read fuse done" "0,1" newline rbitfld.long 0x4 21. "CALIBRATED,Calibrated status" "0,1" newline bitfld.long 0x4 20. "DED_RELOAD,Indicates double error detection occured on reload" "0,1" newline bitfld.long 0x4 19. "SEC_RELOAD,Indicates single error correction occured on reload" "0,1" newline hexmask.long.byte 0x4 15.--18. 1. "FLAGSTATE,Flag state" newline rbitfld.long 0x4 14. "PWOK,Power OK" "0,1" newline rbitfld.long 0x4 13. "ACK,Acknowledge" "0,1" newline bitfld.long 0x4 12. "PROGFAIL,Programming failed" "0,1" newline bitfld.long 0x4 11. "LOCKED,Word Locked" "0,1" newline bitfld.long 0x4 10. "DED,Double error detect" "0,1" newline bitfld.long 0x4 9. "SEC,Single Error Correct" "0,1" line.long 0x8 "OUT_STATUS_CLR,8K OTP Memory STATUS Register" eventfld.long 0x8 27. "DED3,Double error detect" "0,1" newline eventfld.long 0x8 26. "DED2,Double error detect" "0,1" newline eventfld.long 0x8 25. "DED1,Double error detect" "0,1" newline eventfld.long 0x8 24. "DED0,Double error detect" "0,1" newline eventfld.long 0x8 23. "READ_ERROR_INTR,Fuse read error" "0,1" newline eventfld.long 0x8 22. "READ_DONE_INTR,Read fuse done" "0,1" newline eventfld.long 0x8 21. "CALIBRATED,Calibrated status" "0,1" newline eventfld.long 0x8 20. "DED_RELOAD,Indicates double error detection occured on reload" "0,1" newline eventfld.long 0x8 19. "SEC_RELOAD,Indicates single error correction occured on reload" "0,1" newline hexmask.long.byte 0x8 15.--18. 1. "FLAGSTATE,Flag state" newline eventfld.long 0x8 14. "PWOK,Power OK" "0,1" newline eventfld.long 0x8 13. "ACK,Acknowledge" "0,1" newline eventfld.long 0x8 12. "PROGFAIL,Programming failed" "0,1" newline eventfld.long 0x8 11. "LOCKED,Word Locked" "0,1" newline eventfld.long 0x8 10. "DED,Double error detect" "0,1" newline eventfld.long 0x8 9. "SEC,Single Error Correct" "0,1" line.long 0xC "OUT_STATUS_TOG,8K OTP Memory STATUS Register" bitfld.long 0xC 27. "DED3,Double error detect" "0,1" newline bitfld.long 0xC 26. "DED2,Double error detect" "0,1" newline bitfld.long 0xC 25. "DED1,Double error detect" "0,1" newline bitfld.long 0xC 24. "DED0,Double error detect" "0,1" newline bitfld.long 0xC 23. "READ_ERROR_INTR,Fuse read error" "0,1" newline bitfld.long 0xC 22. "READ_DONE_INTR,Read fuse done" "0,1" newline rbitfld.long 0xC 21. "CALIBRATED,Calibrated status" "0,1" newline bitfld.long 0xC 20. "DED_RELOAD,Indicates double error detection occured on reload" "0,1" newline bitfld.long 0xC 19. "SEC_RELOAD,Indicates single error correction occured on reload" "0,1" newline hexmask.long.byte 0xC 15.--18. 1. "FLAGSTATE,Flag state" newline rbitfld.long 0xC 14. "PWOK,Power OK" "0,1" newline rbitfld.long 0xC 13. "ACK,Acknowledge" "0,1" newline bitfld.long 0xC 12. "PROGFAIL,Programming failed" "0,1" newline bitfld.long 0xC 11. "LOCKED,Word Locked" "0,1" newline bitfld.long 0xC 10. "DED,Double error detect" "0,1" newline bitfld.long 0xC 9. "SEC,Single Error Correct" "0,1" rgroup.long 0xB0++0x3 line.long 0x0 "VERSION,OTP Controller Version Register" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major RTL Version" newline hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor RTL Version" newline hexmask.long.word 0x0 0.--15. 1. "STEP,RTL Version Stepping" group.long 0x100++0x3 line.long 0x0 "READ_FUSE_DATA0,OTP Controller Read Data 0 Register" hexmask.long 0x0 0.--31. 1. "DATA,Data" group.long 0x110++0x3 line.long 0x0 "READ_FUSE_DATA1,OTP Controller Read Data 1 Register" hexmask.long 0x0 0.--31. 1. "DATA,Data" group.long 0x120++0x3 line.long 0x0 "READ_FUSE_DATA2,OTP Controller Read Data 2 Register" hexmask.long 0x0 0.--31. 1. "DATA,Data" group.long 0x130++0x3 line.long 0x0 "READ_FUSE_DATA3,OTP Controller Read Data 3 Register" hexmask.long 0x0 0.--31. 1. "DATA,Data" group.long 0x140++0x3 line.long 0x0 "SW_LOCK,SW_LOCK Register" hexmask.long 0x0 0.--31. 1. "SW_LOCK,This register contains lock information which has the same function as the RLOCK fuse words (supplementary fuse words 8 (0x880) and 9 (0x890)) in fuse memory" group.long 0x150++0x3 line.long 0x0 "BIT_LOCK,BIT_LOCK Register" hexmask.long 0x0 0.--31. 1. "BIT_LOCK,Each bit controls the corresponding bit in supplementary fuse word 13 and its shadow register" rgroup.long 0x600++0x3 line.long 0x0 "LOCKED0,OTP Controller Program Locked Status 0 Register" hexmask.long.word 0x0 0.--15. 1. "LOCKED,Stores program locked status for fuse words 0-15." rgroup.long 0x610++0x3 line.long 0x0 "LOCKED1,OTP Controller Program Locked Status 1 Register" hexmask.long 0x0 0.--31. 1. "LOCKED,Stores program locked status for fuse words 16-47" rgroup.long 0x620++0x3 line.long 0x0 "LOCKED2,OTP Controller Program Locked Status 2 Register" hexmask.long 0x0 0.--31. 1. "LOCKED,Stores program locked status for fuse words 48-79" rgroup.long 0x630++0x3 line.long 0x0 "LOCKED3,OTP Controller Program Locked Status 3 Register" hexmask.long 0x0 0.--31. 1. "LOCKED,Stores program locked status for fuse words 80-111" rgroup.long 0x640++0x3 line.long 0x0 "LOCKED4,OTP Controller Program Locked Status 4 Register" hexmask.long 0x0 0.--31. 1. "LOCKED,Stores program locked status for fuse words 112-143" repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CAC800 ad:0x40CAC810 ad:0x40CAC820 ad:0x40CAC830 ad:0x40CAC840 ad:0x40CAC850 ad:0x40CAC860 ad:0x40CAC870 ad:0x40CAC880 ad:0x40CAC890 ad:0x40CAC8A0 ad:0x40CAC8B0 ad:0x40CAC8C0 ad:0x40CAC8D0 ad:0x40CAC8E0 ad:0x40CAC8F0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CAC900 ad:0x40CAC910 ad:0x40CAC920 ad:0x40CAC930 ad:0x40CAC940 ad:0x40CAC950 ad:0x40CAC960 ad:0x40CAC970 ad:0x40CAC980 ad:0x40CAC990 ad:0x40CAC9A0 ad:0x40CAC9B0 ad:0x40CAC9C0 ad:0x40CAC9D0 ad:0x40CAC9E0 ad:0x40CAC9F0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list ad:0x40CACA00 ad:0x40CACA10 ad:0x40CACA20 ad:0x40CACA30 ad:0x40CACA40 ad:0x40CACA50 ad:0x40CACA60 ad:0x40CACA70 ad:0x40CACA80 ad:0x40CACA90 ad:0x40CACAA0 ad:0x40CACAB0 ad:0x40CACAC0 ad:0x40CACAD0 ad:0x40CACAE0 ad:0x40CACAF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list ad:0x40CACB00 ad:0x40CACB10 ad:0x40CACB20 ad:0x40CACB30 ad:0x40CACB40 ad:0x40CACB50 ad:0x40CACB60 ad:0x40CACB70 ad:0x40CACB80 ad:0x40CACB90 ad:0x40CACBA0 ad:0x40CACBB0 ad:0x40CACBC0 ad:0x40CACBD0 ad:0x40CACBE0 ad:0x40CACBF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list ad:0x40CACC00 ad:0x40CACC10 ad:0x40CACC20 ad:0x40CACC30 ad:0x40CACC40 ad:0x40CACC50 ad:0x40CACC60 ad:0x40CACC70 ad:0x40CACC80 ad:0x40CACC90 ad:0x40CACCA0 ad:0x40CACCB0 ad:0x40CACCC0 ad:0x40CACCD0 ad:0x40CACCE0 ad:0x40CACCF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list ad:0x40CACD00 ad:0x40CACD10 ad:0x40CACD20 ad:0x40CACD30 ad:0x40CACD40 ad:0x40CACD50 ad:0x40CACD60 ad:0x40CACD70 ad:0x40CACD80 ad:0x40CACD90 ad:0x40CACDA0 ad:0x40CACDB0 ad:0x40CACDC0 ad:0x40CACDD0 ad:0x40CACDE0 ad:0x40CACDF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list ad:0x40CACE00 ad:0x40CACE10 ad:0x40CACE20 ad:0x40CACE30 ad:0x40CACE40 ad:0x40CACE50 ad:0x40CACE60 ad:0x40CACE70 ad:0x40CACE80 ad:0x40CACE90 ad:0x40CACEA0 ad:0x40CACEB0 ad:0x40CACEC0 ad:0x40CACED0 ad:0x40CACEE0 ad:0x40CACEF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list ad:0x40CACF00 ad:0x40CACF10 ad:0x40CACF20 ad:0x40CACF30 ad:0x40CACF40 ad:0x40CACF50 ad:0x40CACF60 ad:0x40CACF70 ad:0x40CACF80 ad:0x40CACF90 ad:0x40CACFA0 ad:0x40CACFB0 ad:0x40CACFC0 ad:0x40CACFD0 ad:0x40CACFE0 ad:0x40CACFF0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end repeat 16. (list 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C 0x8D 0x8E 0x8F)(list ad:0x40CAD000 ad:0x40CAD010 ad:0x40CAD020 ad:0x40CAD030 ad:0x40CAD040 ad:0x40CAD050 ad:0x40CAD060 ad:0x40CAD070 ad:0x40CAD080 ad:0x40CAD090 ad:0x40CAD0A0 ad:0x40CAD0B0 ad:0x40CAD0C0 ad:0x40CAD0D0 ad:0x40CAD0E0 ad:0x40CAD0F0) tree "FUSEn[$1]" base $2 rgroup.long ($2)++0x3 line.long 0x0 "FUSE,Value of fuse word index" hexmask.long 0x0 0.--31. 1. "BITS,Reflects value of the fuse word" tree.end repeat.end tree.end tree "OSC_RC_400M" base ad:0x0 group.long 0x0++0x3F line.long 0x0 "CTRL0,Control Register 0" hexmask.long.byte 0x0 24.--29. 1. "REF_CLK_DIV,Divide value for ref_clk to generate slow_clk (used inside this IP)" line.long 0x4 "CTRL0_SET,Control Register 0" hexmask.long.byte 0x4 24.--29. 1. "REF_CLK_DIV,Divide value for ref_clk to generate slow_clk (used inside this IP)" line.long 0x8 "CTRL0_CLR,Control Register 0" hexmask.long.byte 0x8 24.--29. 1. "REF_CLK_DIV,Divide value for ref_clk to generate slow_clk (used inside this IP)" line.long 0xC "CTRL0_TOG,Control Register 0" hexmask.long.byte 0xC 24.--29. 1. "REF_CLK_DIV,Divide value for ref_clk to generate slow_clk (used inside this IP)" line.long 0x10 "CTRL1,Control Register 1" hexmask.long.word 0x10 16.--31. 1. "TARGET_COUNT,Target count for the fast clock" hexmask.long.byte 0x10 8.--11. 1. "HYST_PLUS,Positive hysteresis value for the tuned clock" newline hexmask.long.byte 0x10 0.--3. 1. "HYST_MINUS,Negative hysteresis value for the tuned clock" line.long 0x14 "CTRL1_SET,Control Register 1" hexmask.long.word 0x14 16.--31. 1. "TARGET_COUNT,Target count for the fast clock" hexmask.long.byte 0x14 8.--11. 1. "HYST_PLUS,Positive hysteresis value for the tuned clock" newline hexmask.long.byte 0x14 0.--3. 1. "HYST_MINUS,Negative hysteresis value for the tuned clock" line.long 0x18 "CTRL1_CLR,Control Register 1" hexmask.long.word 0x18 16.--31. 1. "TARGET_COUNT,Target count for the fast clock" hexmask.long.byte 0x18 8.--11. 1. "HYST_PLUS,Positive hysteresis value for the tuned clock" newline hexmask.long.byte 0x18 0.--3. 1. "HYST_MINUS,Negative hysteresis value for the tuned clock" line.long 0x1C "CTRL1_TOG,Control Register 1" hexmask.long.word 0x1C 16.--31. 1. "TARGET_COUNT,Target count for the fast clock" hexmask.long.byte 0x1C 8.--11. 1. "HYST_PLUS,Positive hysteresis value for the tuned clock" newline hexmask.long.byte 0x1C 0.--3. 1. "HYST_MINUS,Negative hysteresis value for the tuned clock" line.long 0x20 "CTRL2,Control Register 2" hexmask.long.byte 0x20 24.--31. 1. "OSC_TUNE_VAL,Program the oscillator frequency" bitfld.long 0x20 14. "TUNE_START,Start/Stop tuning" "0: Stop tuning and reset the tuning logic.,1: Start tuning" newline bitfld.long 0x20 12. "TUNE_EN,Freeze/Unfreeze the tuning value" "0: Freezes the tuning at the current tuned value.,1: Unfreezes and continues the tuning operation" bitfld.long 0x20 10. "TUNE_BYP,Bypass the tuning logic" "0: Use the output of tuning logic to run the..,1: Bypass the tuning logic and use the programmed.." line.long 0x24 "CTRL2_SET,Control Register 2" hexmask.long.byte 0x24 24.--31. 1. "OSC_TUNE_VAL,Program the oscillator frequency" bitfld.long 0x24 14. "TUNE_START,Start/Stop tuning" "0,1" newline bitfld.long 0x24 12. "TUNE_EN,Freeze/Unfreeze the tuning value" "0,1" bitfld.long 0x24 10. "TUNE_BYP,Bypass the tuning logic" "0,1" line.long 0x28 "CTRL2_CLR,Control Register 2" hexmask.long.byte 0x28 24.--31. 1. "OSC_TUNE_VAL,Program the oscillator frequency" eventfld.long 0x28 14. "TUNE_START,Start/Stop tuning" "0,1" newline eventfld.long 0x28 12. "TUNE_EN,Freeze/Unfreeze the tuning value" "0,1" eventfld.long 0x28 10. "TUNE_BYP,Bypass the tuning logic" "0,1" line.long 0x2C "CTRL2_TOG,Control Register 2" hexmask.long.byte 0x2C 24.--31. 1. "OSC_TUNE_VAL,Program the oscillator frequency" bitfld.long 0x2C 14. "TUNE_START,Start/Stop tuning" "0,1" newline bitfld.long 0x2C 12. "TUNE_EN,Freeze/Unfreeze the tuning value" "0,1" bitfld.long 0x2C 10. "TUNE_BYP,Bypass the tuning logic" "0,1" line.long 0x30 "CTRL3,Control Register 3" hexmask.long.word 0x30 16.--31. 1. "COUNT_1M_CLK,Count for the locked clk_1m_out" bitfld.long 0x30 10. "MUX_1M_CLK,Select free/locked 1MHz output" "0: Select free-running 1MHz to be put out on..,1: Select locked 1MHz to be put out on clk_1m_out" newline bitfld.long 0x30 8. "EN_1M_CLK,Enable 1MHz output Clock" "0: Enable the output (clk_1m_out),1: Disable the output (clk_1m_out)" bitfld.long 0x30 0. "CLR_ERR,Clear the error flag CLK1M_ERR" "0: No effect,1: Clears the error flag CLK1M_ERR in status.." line.long 0x34 "CTRL3_SET,Control Register 3" hexmask.long.word 0x34 16.--31. 1. "COUNT_1M_CLK,Count for the locked clk_1m_out" bitfld.long 0x34 10. "MUX_1M_CLK,Select free/locked 1MHz output" "0,1" newline bitfld.long 0x34 8. "EN_1M_CLK,Enable 1MHz output Clock" "0,1" bitfld.long 0x34 0. "CLR_ERR,Clear the error flag CLK1M_ERR" "0,1" line.long 0x38 "CTRL3_CLR,Control Register 3" hexmask.long.word 0x38 16.--31. 1. "COUNT_1M_CLK,Count for the locked clk_1m_out" eventfld.long 0x38 10. "MUX_1M_CLK,Select free/locked 1MHz output" "0,1" newline eventfld.long 0x38 8. "EN_1M_CLK,Enable 1MHz output Clock" "0,1" eventfld.long 0x38 0. "CLR_ERR,Clear the error flag CLK1M_ERR" "0,1" line.long 0x3C "CTRL3_TOG,Control Register 3" hexmask.long.word 0x3C 16.--31. 1. "COUNT_1M_CLK,Count for the locked clk_1m_out" bitfld.long 0x3C 10. "MUX_1M_CLK,Select free/locked 1MHz output" "0,1" newline bitfld.long 0x3C 8. "EN_1M_CLK,Enable 1MHz output Clock" "0,1" bitfld.long 0x3C 0. "CLR_ERR,Clear the error flag CLK1M_ERR" "0,1" rgroup.long 0x50++0x2F line.long 0x0 "STAT0,Status Register 0" bitfld.long 0x0 0. "CLK1M_ERR,Error flag for clk_1m_locked" "0: No effect,1: The count value has been reached within one.." line.long 0x4 "STAT0_SET,Status Register 0" bitfld.long 0x4 0. "CLK1M_ERR,Error flag for clk_1m_locked" "0,1" line.long 0x8 "STAT0_CLR,Status Register 0" eventfld.long 0x8 0. "CLK1M_ERR,Error flag for clk_1m_locked" "0,1" line.long 0xC "STAT0_TOG,Status Register 0" bitfld.long 0xC 0. "CLK1M_ERR,Error flag for clk_1m_locked" "0,1" line.long 0x10 "STAT1,Status Register 1" hexmask.long.word 0x10 16.--31. 1. "CURR_COUNT_VAL,Current count for the fast clock" line.long 0x14 "STAT1_SET,Status Register 1" hexmask.long.word 0x14 16.--31. 1. "CURR_COUNT_VAL,Current count for the fast clock" line.long 0x18 "STAT1_CLR,Status Register 1" hexmask.long.word 0x18 16.--31. 1. "CURR_COUNT_VAL,Current count for the fast clock" line.long 0x1C "STAT1_TOG,Status Register 1" hexmask.long.word 0x1C 16.--31. 1. "CURR_COUNT_VAL,Current count for the fast clock" line.long 0x20 "STAT2,Status Register 2" hexmask.long.byte 0x20 24.--31. 1. "CURR_OSC_TUNE_VAL,Current tuning value used by oscillator" line.long 0x24 "STAT2_SET,Status Register 2" hexmask.long.byte 0x24 24.--31. 1. "CURR_OSC_TUNE_VAL,Current tuning value used by oscillator" line.long 0x28 "STAT2_CLR,Status Register 2" hexmask.long.byte 0x28 24.--31. 1. "CURR_OSC_TUNE_VAL,Current tuning value used by oscillator" line.long 0x2C "STAT2_TOG,Status Register 2" hexmask.long.byte 0x2C 24.--31. 1. "CURR_OSC_TUNE_VAL,Current tuning value used by oscillator" tree.end tree "OTFAD" base ad:0x0 tree "OTFAD1" base ad:0x400CC000 group.long 0xC00++0x7 line.long 0x0 "CR,Control Register" bitfld.long 0x0 31. "GE,Global OTFAD Enable" "0: OTFAD has decryption disabled. All data fetched..,1: OTFAD has decryption enabled and processes data.." bitfld.long 0x0 30. "SKBP,Start key blob processing" "0: Key blob processing is not initiated.,1: Properly-enabled key blob processing is initiated." newline bitfld.long 0x0 7. "RRAE,Restricted Register Access Enable" "0: Register access is fully enabled. The OTFAD..,1: Register access is restricted and only the CR SR.." bitfld.long 0x0 5. "KBPE,Key Blob Processing Enable" "0: Key blob processing is disabled.,1: Key blob processing is enabled." newline bitfld.long 0x0 4. "KBSE,Key Blob Scramble Enable" "0: Key blob KEK scrambling is disabled.,1: Key blob KEK scrambling is enabled." bitfld.long 0x0 3. "FLDM,Force Logically Disabled Mode" "0: No effect on the operating mode.,1: Force entry into LDM after a write with this.." newline bitfld.long 0x0 1. "FERR,Force Error" "0: No effect on the SR[KBERE] indicator.,1: SR[KBERR] is immediately set after a write with.." line.long 0x4 "SR,Status Register" rbitfld.long 0x4 31. "KBD,Key Blob Processing Done" "0: Key blob processing was not enabled or is not..,1: Key blob processing was enabled and is complete." rbitfld.long 0x4 30. "KBPE,Key Blob Processing Enable" "0: Key blob processing is not enabled.,1: Key blob processing is enabled." newline rbitfld.long 0x4 29. "GEM,Global Enable Mode" "0: OTFAD is disabled. All data fetched by the..,1: OTFAD is enabled and processes data fetched by.." rbitfld.long 0x4 28. "RRAM,Restricted Register Access Mode" "0: Register access is fully enabled. The OTFAD..,1: Register access is restricted and only the CR SR.." newline hexmask.long.byte 0x4 24.--27. 1. "HRL,Hardware Revision Level" rbitfld.long 0x4 19. "CTXIE3,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." newline rbitfld.long 0x4 18. "CTXIE2,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." rbitfld.long 0x4 17. "CTXIE1,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." newline rbitfld.long 0x4 16. "CTXIE0,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." rbitfld.long 0x4 11. "CTXER3,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." newline rbitfld.long 0x4 10. "CTXER2,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." rbitfld.long 0x4 9. "CTXER1,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." newline rbitfld.long 0x4 8. "CTXER0,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." hexmask.long.byte 0x4 4.--7. 1. "NCTX,Number of Contexts" newline rbitfld.long 0x4 2.--3. "MODE,Operating Mode" "0: Operating in Normal mode (NRM),1: Unused (reserved),2: Unused (reserved),3: Operating in Logically Disabled Mode (LDM)" rbitfld.long 0x4 1. "MDPCP,MDPC Present" "0,1" newline eventfld.long 0x4 0. "KBERR,Key Blob Error" "0: No key blob error detected.,1: One or more key blob errors has been detected." repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x400CCD00 ad:0x400CCD40 ad:0x400CCD80 ad:0x400CCDC0) tree "CTX[$1]" base $2 repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CTX_KEY$1,AES Key Word" hexmask.long 0x0 0.--31. 1. "KEY,AES Key" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "CTX_CTR$1,AES Counter Word" hexmask.long 0x0 0.--31. 1. "CTR,AES Counter" repeat.end group.long ($2+0x18)++0x7 line.long 0x0 "CTX_RGD_W0,AES Region Descriptor Word0" hexmask.long.tbyte 0x0 10.--31. 1. "SRTADDR,Start Address" line.long 0x4 "CTX_RGD_W1,AES Region Descriptor Word1" hexmask.long.tbyte 0x4 10.--31. 1. "ENDADDR,End Address" bitfld.long 0x4 2. "RO,Read-Only" "0: The context registers can be accessed normally..,1: The context registers are read-only and accesses.." newline bitfld.long 0x4 1. "ADE,AES Decryption Enable." "0: Bypass the fetched data.,1: Perform the CTR-AES128 mode decryption on the.." bitfld.long 0x4 0. "VLD,Valid" "0: Context is invalid.,1: Context is valid." tree.end repeat.end tree.end tree "OTFAD2" base ad:0x400D0000 group.long 0xC00++0x7 line.long 0x0 "CR,Control Register" bitfld.long 0x0 31. "GE,Global OTFAD Enable" "0: OTFAD has decryption disabled. All data fetched..,1: OTFAD has decryption enabled and processes data.." bitfld.long 0x0 30. "SKBP,Start key blob processing" "0: Key blob processing is not initiated.,1: Properly-enabled key blob processing is initiated." newline bitfld.long 0x0 7. "RRAE,Restricted Register Access Enable" "0: Register access is fully enabled. The OTFAD..,1: Register access is restricted and only the CR SR.." bitfld.long 0x0 5. "KBPE,Key Blob Processing Enable" "0: Key blob processing is disabled.,1: Key blob processing is enabled." newline bitfld.long 0x0 4. "KBSE,Key Blob Scramble Enable" "0: Key blob KEK scrambling is disabled.,1: Key blob KEK scrambling is enabled." bitfld.long 0x0 3. "FLDM,Force Logically Disabled Mode" "0: No effect on the operating mode.,1: Force entry into LDM after a write with this.." newline bitfld.long 0x0 1. "FERR,Force Error" "0: No effect on the SR[KBERE] indicator.,1: SR[KBERR] is immediately set after a write with.." line.long 0x4 "SR,Status Register" rbitfld.long 0x4 31. "KBD,Key Blob Processing Done" "0: Key blob processing was not enabled or is not..,1: Key blob processing was enabled and is complete." rbitfld.long 0x4 30. "KBPE,Key Blob Processing Enable" "0: Key blob processing is not enabled.,1: Key blob processing is enabled." newline rbitfld.long 0x4 29. "GEM,Global Enable Mode" "0: OTFAD is disabled. All data fetched by the..,1: OTFAD is enabled and processes data fetched by.." rbitfld.long 0x4 28. "RRAM,Restricted Register Access Mode" "0: Register access is fully enabled. The OTFAD..,1: Register access is restricted and only the CR SR.." newline hexmask.long.byte 0x4 24.--27. 1. "HRL,Hardware Revision Level" rbitfld.long 0x4 19. "CTXIE3,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." newline rbitfld.long 0x4 18. "CTXIE2,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." rbitfld.long 0x4 17. "CTXIE1,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." newline rbitfld.long 0x4 16. "CTXIE0,Context Integrity Error" "0: No key blob integrity error was detected for..,1: A key blob integrity error was detected in.." rbitfld.long 0x4 11. "CTXER3,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." newline rbitfld.long 0x4 10. "CTXER2,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." rbitfld.long 0x4 9. "CTXER1,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." newline rbitfld.long 0x4 8. "CTXER0,Context Error" "0: No key blob error was detected for context 'n'.,1: A key blob integrity error might have been.." hexmask.long.byte 0x4 4.--7. 1. "NCTX,Number of Contexts" newline rbitfld.long 0x4 2.--3. "MODE,Operating Mode" "0: Operating in Normal mode (NRM),1: Unused (reserved),2: Unused (reserved),3: Operating in Logically Disabled Mode (LDM)" rbitfld.long 0x4 1. "MDPCP,MDPC Present" "0,1" newline eventfld.long 0x4 0. "KBERR,Key Blob Error" "0: No key blob error detected.,1: One or more key blob errors has been detected." repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x400D0D00 ad:0x400D0D40 ad:0x400D0D80 ad:0x400D0DC0) tree "CTX[$1]" base $2 repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2)++0x3 line.long 0x0 "CTX_KEY$1,AES Key Word" hexmask.long 0x0 0.--31. 1. "KEY,AES Key" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "CTX_CTR$1,AES Counter Word" hexmask.long 0x0 0.--31. 1. "CTR,AES Counter" repeat.end group.long ($2+0x18)++0x7 line.long 0x0 "CTX_RGD_W0,AES Region Descriptor Word0" hexmask.long.tbyte 0x0 10.--31. 1. "SRTADDR,Start Address" line.long 0x4 "CTX_RGD_W1,AES Region Descriptor Word1" hexmask.long.tbyte 0x4 10.--31. 1. "ENDADDR,End Address" bitfld.long 0x4 2. "RO,Read-Only" "0: The context registers can be accessed normally..,1: The context registers are read-only and accesses.." newline bitfld.long 0x4 1. "ADE,AES Decryption Enable." "0: Bypass the fetched data.,1: Perform the CTR-AES128 mode decryption on the.." bitfld.long 0x4 0. "VLD,Valid" "0: Context is invalid.,1: Context is valid." tree.end repeat.end tree.end tree.end tree "PDM" base ad:0x40C20000 group.long 0x0++0xB line.long 0x0 "CTRL_1,PDM Control register 1" bitfld.long 0x0 31. "MDIS,Module Disable" "0: Normal Mode,1: Disable/Low Leakage Mode" bitfld.long 0x0 30. "DOZEN,DOZE enable" "0,1" newline bitfld.long 0x0 29. "PDMIEN,PDM Enable" "0: PDM stopped,1: PDM operation started" bitfld.long 0x0 28. "DBG,Debug Mode" "0: Normal Mode,1: Debug Mode" newline bitfld.long 0x0 27. "SRES,Software-reset bit" "0: No action,1: Software reset" bitfld.long 0x0 26. "DBGE,Module Enable in Debug" "0: Disabled after completing the current frame,1: Enabled" newline bitfld.long 0x0 24.--25. "DISEL,DMA Interrupt Selection" "0: DMA and interrupt requests disabled,1: DMA requests enabled,2: Interrupt requests enabled,?" bitfld.long 0x0 23. "ERREN,Error Interruption Enable" "0: Error Interrupts disabled,1: Error Interrupts enabled" newline bitfld.long 0x0 7. "CH7EN,Channel 7 Enable" "0,1" bitfld.long 0x0 6. "CH6EN,Channel 6 Enable" "0,1" newline bitfld.long 0x0 5. "CH5EN,Channel 5 Enable" "0,1" bitfld.long 0x0 4. "CH4EN,Channel 4 Enable" "0,1" newline bitfld.long 0x0 3. "CH3EN,Channel 3 Enable" "0,1" bitfld.long 0x0 2. "CH2EN,Channel 2 Enable" "0,1" newline bitfld.long 0x0 1. "CH1EN,Channel 1 Enable" "0,1" bitfld.long 0x0 0. "CH0EN,Channel 0 Enable" "0,1" line.long 0x4 "CTRL_2,PDM Control register 2" bitfld.long 0x4 25.--27. "QSEL,Quality Mode" "0: Medium quality mode,1: High quality mode,?,?,4: Very low quality 2 mode,5: Very low quality 1 mode,6: Very low quality 0 mode,7: Low quality mode" hexmask.long.byte 0x4 16.--19. 1. "CICOSR,CIC Decimation Rate" newline hexmask.long.byte 0x4 0.--7. 1. "CLKDIV,Clock Divider" line.long 0x8 "STAT,PDM Status register" rbitfld.long 0x8 31. "BSY_FIL,Busy Flag" "0: PDM is stopped,1: PDM is running" rbitfld.long 0x8 30. "FIR_RDY,Filter Data Ready" "0: Filter data is not reliable,1: Filter data is reliable" newline eventfld.long 0x8 29. "LOWFREQF,Low Frequency Flag" "0: CLKDIV value is OK,1: CLKDIV value is too low" eventfld.long 0x8 7. "CH7F,Channel 7 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." newline eventfld.long 0x8 6. "CH6F,Channel 6 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." eventfld.long 0x8 5. "CH5F,Channel 5 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." newline eventfld.long 0x8 4. "CH4F,Channel 4 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." eventfld.long 0x8 3. "CH3F,Channel 3 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." newline eventfld.long 0x8 2. "CH2F,Channel 2 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." eventfld.long 0x8 1. "CH1F,Channel 1 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." newline eventfld.long 0x8 0. "CH0F,Channel 0 Output Data Flag" "0: Channel's FIFO did not reach the number of..,1: Channel's FIFO reached the number of elements.." group.long 0x10++0x7 line.long 0x0 "FIFO_CTRL,PDM FIFO Control register" bitfld.long 0x0 0.--2. "FIFOWMK,FIFO Watermark Control" "0,1,2,3,4,5,6,7" line.long 0x4 "FIFO_STAT,PDM FIFO Status register" eventfld.long 0x4 15. "FIFOUND7,FIFO Underflow Exception flag for Channel 7" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" eventfld.long 0x4 14. "FIFOUND6,FIFO Underflow Exception flag for Channel 6" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" newline eventfld.long 0x4 13. "FIFOUND5,FIFO Underflow Exception flag for Channel 5" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" eventfld.long 0x4 12. "FIFOUND4,FIFO Underflow Exception flag for Channel 4" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" newline eventfld.long 0x4 11. "FIFOUND3,FIFO Underflow Exception flag for Channel 3" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" eventfld.long 0x4 10. "FIFOUND2,FIFO Underflow Exception flag for Channel 2" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" newline eventfld.long 0x4 9. "FIFOUND1,FIFO Underflow Exception flag for Channel 1" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" eventfld.long 0x4 8. "FIFOUND0,FIFO Underflow Exception flag for Channel 0" "0: No exception by FIFO Underflow,1: Exception by FIFO underflow" newline eventfld.long 0x4 7. "FIFOOVF7,FIFO Overflow Exception flag for Channel 7" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" eventfld.long 0x4 6. "FIFOOVF6,FIFO Overflow Exception flag for Channel 6" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" newline eventfld.long 0x4 5. "FIFOOVF5,FIFO Overflow Exception flag for Channel 5" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" eventfld.long 0x4 4. "FIFOOVF4,FIFO Overflow Exception flag for Channel 4" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" newline eventfld.long 0x4 3. "FIFOOVF3,FIFO Overflow Exception flag for Channel 3" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" eventfld.long 0x4 2. "FIFOOVF2,FIFO Overflow Exception flag for Channel 2" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" newline eventfld.long 0x4 1. "FIFOOVF1,FIFO Overflow Exception flag for Channel 1" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" eventfld.long 0x4 0. "FIFOOVF0,FIFO Overflow Exception flag for Channel 0" "0: No exception by FIFO overflow,1: Exception by FIFO overflow" repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x24)++0x3 line.long 0x0 "DATACH[$1],PDM Output Result Register" hexmask.long 0x0 0.--31. 1. "DATA,Channel n Data" repeat.end group.long 0x64++0x3 line.long 0x0 "DC_CTRL,PDM DC Remover Control register" bitfld.long 0x0 14.--15. "DCCONFIG7,Channel 7 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" bitfld.long 0x0 12.--13. "DCCONFIG6,Channel 6 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" newline bitfld.long 0x0 10.--11. "DCCONFIG5,Channel 5 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" bitfld.long 0x0 8.--9. "DCCONFIG4,Channel 4 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" newline bitfld.long 0x0 6.--7. "DCCONFIG3,Channel 3 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" bitfld.long 0x0 4.--5. "DCCONFIG2,Channel 2 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" newline bitfld.long 0x0 2.--3. "DCCONFIG1,Channel 1 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" bitfld.long 0x0 0.--1. "DCCONFIG0,Channel 0 DC Remover Configuration" "0: DC Remover cut-off at 21Hz,1: DC Remover cut-off at 83Hz,2: DC Remover cut-off at 152Hz,3: DC Remover is bypassed" group.long 0x74++0x3 line.long 0x0 "RANGE_CTRL,PDM Range Control register" hexmask.long.byte 0x0 28.--31. 1. "RANGEADJ7,Channel 7 Range Adjustment" hexmask.long.byte 0x0 24.--27. 1. "RANGEADJ6,Channel 6 Range Adjustment" newline hexmask.long.byte 0x0 20.--23. 1. "RANGEADJ5,Channel 5 Range Adjustment" hexmask.long.byte 0x0 16.--19. 1. "RANGEADJ4,Channel 4 Range Adjustment" newline hexmask.long.byte 0x0 12.--15. 1. "RANGEADJ3,Channel 3 Range Adjustment" hexmask.long.byte 0x0 8.--11. 1. "RANGEADJ2,Channel 2 Range Adjustment" newline hexmask.long.byte 0x0 4.--7. 1. "RANGEADJ1,Channel 1 Range Adjustment" hexmask.long.byte 0x0 0.--3. 1. "RANGEADJ0,Channel 0 Range Adjustment" group.long 0x7C++0x3 line.long 0x0 "RANGE_STAT,PDM Range Status register" eventfld.long 0x0 23. "RANGEUNF7,Channel 7 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" eventfld.long 0x0 22. "RANGEUNF6,Channel 6 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" newline eventfld.long 0x0 21. "RANGEUNF5,Channel 5 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" eventfld.long 0x0 20. "RANGEUNF4,Channel 4 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" newline eventfld.long 0x0 19. "RANGEUNF3,Channel 3 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" eventfld.long 0x0 18. "RANGEUNF2,Channel 2 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" newline eventfld.long 0x0 17. "RANGEUNF1,Channel 1 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" eventfld.long 0x0 16. "RANGEUNF0,Channel 0 Range Underflow Error Flag" "0: No exception by range underflow,1: Exception by range underflow" newline eventfld.long 0x0 7. "RANGEOVF7,Channel 7 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" eventfld.long 0x0 6. "RANGEOVF6,Channel 6 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" newline eventfld.long 0x0 5. "RANGEOVF5,Channel 5 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" eventfld.long 0x0 4. "RANGEOVF4,Channel 4 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" newline eventfld.long 0x0 3. "RANGEOVF3,Channel 3 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" eventfld.long 0x0 2. "RANGEOVF2,Channel 2 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" newline eventfld.long 0x0 1. "RANGEOVF1,Channel 1 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" eventfld.long 0x0 0. "RANGEOVF0,Channel 0 Range Overflow Error Flag" "0: No exception by range overflow,1: Exception by range overflow" group.long 0x90++0x13 line.long 0x0 "VAD0_CTRL_1,Voice Activity Detector 0 Control register" bitfld.long 0x0 24.--26. "VADCHSEL,Voice Activity Detector Channel Selector" "0,1,2,3,4,5,6,7" hexmask.long.byte 0x0 16.--19. 1. "VADCICOSR,Voice Activity Detector CIC Oversampling Rate" newline hexmask.long.byte 0x0 8.--12. 1. "VADINITT,Voice Activity Detector Initialization Time" bitfld.long 0x0 4. "VADST10,Voice Activity Detector Internal Filters Initialization" "0: Normal operation.,1: Filters are initialized." newline bitfld.long 0x0 3. "VADERIE,Voice Activity Detector Error Interruption Enable" "0: HWVAD Error Interrupts disabled,1: HWVAD Error Interrupts enabled" bitfld.long 0x0 2. "VADIE,Voice Activity Detector Interruption Enable" "0: HWVAD Interrupts disabled,1: HWVAD Interrupts enabled" newline bitfld.long 0x0 1. "VADRST,Voice Activity Detector Reset" "0,1" bitfld.long 0x0 0. "VADEN,Voice Activity Detector Enable" "0: The HWVAD is disabled,1: The HWVAD is enabled" line.long 0x4 "VAD0_CTRL_2,Voice Activity Detector 0 Control register" bitfld.long 0x4 31. "VADFRENDIS,Voice Activity Detector Frame Energy Disable" "0: Frame energy calculus enabled.,1: Frame energy calculus disabled." bitfld.long 0x4 30. "VADPREFEN,Voice Activity Detector Pre Filter Enable" "0: Pre-filter is bypassed.,1: Pre-filter is enabled." newline bitfld.long 0x4 28. "VADFOUTDIS,Voice Activity Detector Force Output Disable" "0: Output is enabled.,1: Output is disabled." hexmask.long.byte 0x4 16.--21. 1. "VADFRAMET,Voice Activity Detector Frame Time" newline hexmask.long.byte 0x4 8.--11. 1. "VADINPGAIN,Voice Activity Detector Input Gain" bitfld.long 0x4 0.--1. "VADHPF,Voice Activity Detector High-Pass Filter" "0: Filter bypassed.,1: Cut-off frequency at 1750Hz.,2: Cut-off frequency at 215Hz.,3: Cut-off frequency at 102Hz." line.long 0x8 "VAD0_STAT,Voice Activity Detector 0 Status register" rbitfld.long 0x8 31. "VADINITF,Voice Activity Detector Initialization Flag" "0: HWVAD is not being initialized.,1: HWVAD is being initialized." eventfld.long 0x8 16. "VADINSATF,Voice Activity Detector Input Saturation Flag" "0: No exception,1: Exception" newline rbitfld.long 0x8 15. "VADEF,Voice Activity Detector Event Flag" "0: Voice activity not detected,1: Voice activity detected" eventfld.long 0x8 0. "VADIF,Voice Activity Detector Interrupt Flag" "0: Voice activity not detected,1: Voice activity detected" line.long 0xC "VAD0_SCONFIG,Voice Activity Detector 0 Signal Configuration" bitfld.long 0xC 31. "VADSFILEN,Voice Activity Detector Signal Filter Enable" "0: Signal filter is disabled.,1: Signal filter is enabled." bitfld.long 0xC 30. "VADSMAXEN,Voice Activity Detector Signal Maximum Enable" "0: Maximum block is bypassed.,1: Maximum block is enabled." newline hexmask.long.byte 0xC 0.--3. 1. "VADSGAIN,Voice Activity Detector Signal Gain" line.long 0x10 "VAD0_NCONFIG,Voice Activity Detector 0 Noise Configuration" bitfld.long 0x10 31. "VADNFILAUTO,Voice Activity Detector Noise Filter Auto" "0: Noise filter is always enabled.,1: Noise filter is enabled/disabled based on voice.." bitfld.long 0x10 30. "VADNMINEN,Voice Activity Detector Noise Minimum Enable" "0: Minimum block is bypassed.,1: Minimum block is enabled." newline bitfld.long 0x10 29. "VADNDECEN,Voice Activity Detector Noise Decimation Enable" "0: Noise input is not decimated.,1: Noise input is decimated." bitfld.long 0x10 28. "VADNOREN,Voice Activity Detector Noise OR Enable" "0: Noise input is not decimated.,1: Noise input is decimated." newline hexmask.long.byte 0x10 8.--12. 1. "VADNFILADJ,Voice Activity Detector Noise Filter Adjustment" hexmask.long.byte 0x10 0.--3. 1. "VADNGAIN,Voice Activity Detector Noise Gain" rgroup.long 0xA4++0x3 line.long 0x0 "VAD0_NDATA,Voice Activity Detector 0 Noise Data" hexmask.long.word 0x0 0.--15. 1. "VADNDATA,Voice Activity Detector Noise Data" group.long 0xA8++0x3 line.long 0x0 "VAD0_ZCD,Voice Activity Detector 0 Zero-Crossing Detector" hexmask.long.word 0x0 16.--25. 1. "VADZCDTH,Zero-Crossing Detector Threshold" hexmask.long.byte 0x0 8.--11. 1. "VADZCDADJ,Zero-Crossing Detector Adjustment" newline bitfld.long 0x0 4. "VADZCDAND,Zero-Crossing Detector AND Behavior" "0: The ZCD result is OR'ed with the energy-based..,1: The ZCD result is AND'ed with the energy-based.." bitfld.long 0x0 2. "VADZCDAUTO,Zero-Crossing Detector Automatic Threshold" "0: The ZCD threshold is not estimated automatically,1: The ZCD threshold is estimated automatically" newline bitfld.long 0x0 0. "VADZCDEN,Zero-Crossing Detector Enable" "0: The ZCD is disabled,1: The ZCD is enabled" tree.end tree "PGMC_BPC" base ad:0x0 tree "PGMC_BPC0" base ad:0x40C88000 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC1" base ad:0x40C88200 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC2" base ad:0x40C88400 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC3" base ad:0x40C88600 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC4" base ad:0x40C88800 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC5" base ad:0x40C88A00 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC6" base ad:0x40C88C00 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree "PGMC_BPC7" base ad:0x40C88E00 group.long 0x4++0x3 line.long 0x0 "BPC_AUTHEN_CTRL,BPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" newline bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0: Allow only secure mode to access basic power..,1: Allow both secure and non-secure mode to access.." newline bitfld.long 0x0 0. "USER,Allow user mode access" "0: Allow only privilege mode to access basic power..,1: Allow both privilege and user mode to access.." group.long 0x10++0x7 line.long 0x0 "BPC_MODE,BPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" newline bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "BPC_POWER_CTRL,BPC power control" hexmask.long.word 0x4 16.--31. 1. "PWR_OFF_AT_SP,Power off when system enters Setpoint number" newline bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" newline bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" newline bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" newline bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,0x1: Power off when domain enters SUSPEND mode" "?,1: Power off when domain enters SUSPEND mode" newline bitfld.long 0x4 2. "PWR_OFF_AT_STOP,0x1: Power off when domain enters STOP mode" "?,1: Power off when domain enters STOP mode" newline bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,0x1: Power off when domain enters WAIT mode" "?,1: Power off when domain enters WAIT mode" group.long 0x2C++0x3 line.long 0x0 "BPC_FLAG,BPC flag" eventfld.long 0x0 0. "PDN_FLAG,set to 1 after power switch off cleared by writing 1" "0,1" group.long 0x40++0x7 line.long 0x0 "BPC_SSAR_SAVE_CTRL,BPC SSAR save control" hexmask.long.word 0x0 16.--31. 1. "SAVE_AT_SP,Save data when system enters a Setpoint." newline bitfld.long 0x0 3. "SAVE_AT_SUSPEND,Save data when domain enters SUSPEND mode" "0,1" newline bitfld.long 0x0 2. "SAVE_AT_STOP,Save data when domain enters STOP mode" "0,1" newline bitfld.long 0x0 1. "SAVE_AT_WAIT,Save data when domain enters WAIT mode" "0,1" newline bitfld.long 0x0 0. "SAVE_AT_RUN,Save data at RUN mode software writting 0x1 to trigger SSARC to execute save process" "0,1" line.long 0x4 "BPC_SSAR_RESTORE_CTRL,BPC SSAR restore control" hexmask.long.word 0x4 16.--31. 1. "RESTORE_AT_SP,Restore data when system enters a Setpoint." newline bitfld.long 0x4 0. "RESTORE_AT_RUN,Restore data at RUN mode" "0,1" tree.end tree.end tree "PGMC_CPC" base ad:0x0 tree "PGMC_CPC0" base ad:0x40C89000 group.long 0x4++0x3 line.long 0x0 "CPC_AUTHEN_CTRL,CPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0,1" bitfld.long 0x0 0. "USER,Allow user mode access" "0,1" group.long 0x10++0x7 line.long 0x0 "CPC_CORE_MODE,CPC Core Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,?,?" line.long 0x4 "CPC_CORE_POWER_CTRL,CPC core power control" bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,Power off when domain enters SUSPEND mode" "0,1" bitfld.long 0x4 2. "PWR_OFF_AT_STOP,Power off when domain enters STOP mode" "0,1" bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,Power off when domain enters WAIT mode" "0,1" group.long 0x2C++0x3 line.long 0x0 "CPC_FLAG,CPC flag" eventfld.long 0x0 0. "CORE_PDN_FLAG,set to 1 after core power switch off cleared by writing 1" "0,1" group.long 0x40++0xF line.long 0x0 "CPC_CACHE_MODE,CPC Cache Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "CPC_CACHE_CM_CTRL,CPC cache CPU mode control" bitfld.long 0x4 16. "MLPL_SOFT,Memory Low Power Level (MLPL) software change request keep 1 until MLPL transition complete" "0,1" hexmask.long.byte 0x4 12.--15. 1. "MLPL_AT_SUSPEND,Memory Low Power Level (MLPL) at SUSPEND mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 8.--11. 1. "MLPL_AT_STOP,Memory Low Power Level (MLPL) at STOP mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 4.--7. 1. "MLPL_AT_WAIT,Memory Low Power Level (MLPL) at WAIT mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x4 0.--3. 1. "MLPL_AT_RUN,Memory Low Power Level (MLPL) at RUN mode" line.long 0x8 "CPC_CACHE_SP_CTRL_0,CPC cache Setpoint control 0" hexmask.long.byte 0x8 28.--31. 1. "MLPL_AT_SP7,Memory Low Power Level (MLPL) at Setpoint 7. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 24.--27. 1. "MLPL_AT_SP6,Memory Low Power Level (MLPL) at Setpoint 6. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 20.--23. 1. "MLPL_AT_SP5,Memory Low Power Level (MLPL) at Setpoint 5. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 16.--19. 1. "MLPL_AT_SP4,Memory Low Power Level (MLPL) at Setpoint 4. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x8 12.--15. 1. "MLPL_AT_SP3,Memory Low Power Level (MLPL) at Setpoint 3. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 8.--11. 1. "MLPL_AT_SP2,Memory Low Power Level (MLPL) at Setpoint 2. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 4.--7. 1. "MLPL_AT_SP1,Memory Low Power Level (MLPL) at Setpoint 1. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 0.--3. 1. "MLPL_AT_SP0,Memory Low Power Level (MLPL) at Setpoint 0. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." line.long 0xC "CPC_CACHE_SP_CTRL_1,CPC cache Setpoint control 1" hexmask.long.byte 0xC 28.--31. 1. "MLPL_AT_SP15,Memory Low Power Level (MLPL) at Setpoint 15. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 24.--27. 1. "MLPL_AT_SP14,Memory Low Power Level (MLPL) at Setpoint 14. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 20.--23. 1. "MLPL_AT_SP13,Memory Low Power Level (MLPL) at Setpoint 13. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 16.--19. 1. "MLPL_AT_SP12,Memory Low Power Level (MLPL) at Setpoint 12. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0xC 12.--15. 1. "MLPL_AT_SP11,Memory Low Power Level (MLPL) at Setpoint 11. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 8.--11. 1. "MLPL_AT_SP10,Memory Low Power Level (MLPL) at Setpoint 10. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 4.--7. 1. "MLPL_AT_SP9,Memory Low Power Level (MLPL) at Setpoint 9. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 0.--3. 1. "MLPL_AT_SP8,Memory Low Power Level (MLPL) at Setpoint 8. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." group.long 0xC0++0xF line.long 0x0 "CPC_LMEM_MODE,CPC local memory Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "CPC_LMEM_CM_CTRL,CPC local memory CPU mode control" bitfld.long 0x4 16. "MLPL_SOFT,Memory Low Power Level (MLPL) software change request keep 1 until MLPL transition complete" "0,1" hexmask.long.byte 0x4 12.--15. 1. "MLPL_AT_SUSPEND,Memory Low Power Level (MLPL) at SUSPEND mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 8.--11. 1. "MLPL_AT_STOP,Memory Low Power Level (MLPL) at STOP mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 4.--7. 1. "MLPL_AT_WAIT,Memory Low Power Level (MLPL) at WAIT mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x4 0.--3. 1. "MLPL_AT_RUN,Memory Low Power Level (MLPL) at RUN mode" line.long 0x8 "CPC_LMEM_SP_CTRL_0,CPC local memory Setpoint control 0" hexmask.long.byte 0x8 28.--31. 1. "MLPL_AT_SP7,Memory Low Power Level (MLPL) at Setpoint 7. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 24.--27. 1. "MLPL_AT_SP6,Memory Low Power Level (MLPL) at Setpoint 6. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 20.--23. 1. "MLPL_AT_SP5,Memory Low Power Level (MLPL) at Setpoint 5. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 16.--19. 1. "MLPL_AT_SP4,Memory Low Power Level (MLPL) at Setpoint 4. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x8 12.--15. 1. "MLPL_AT_SP3,Memory Low Power Level (MLPL) at Setpoint 3. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 8.--11. 1. "MLPL_AT_SP2,Memory Low Power Level (MLPL) at Setpoint 2. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 4.--7. 1. "MLPL_AT_SP1,Memory Low Power Level (MLPL) at Setpoint 1. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 0.--3. 1. "MLPL_AT_SP0,Memory Low Power Level (MLPL) at Setpoint 0. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." line.long 0xC "CPC_LMEM_SP_CTRL_1,CPC local memory Setpoint control 1" hexmask.long.byte 0xC 28.--31. 1. "MLPL_AT_SP15,Memory Low Power Level (MLPL) at Setpoint 15. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 24.--27. 1. "MLPL_AT_SP14,Memory Low Power Level (MLPL) at Setpoint 14. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 20.--23. 1. "MLPL_AT_SP13,Memory Low Power Level (MLPL) at Setpoint 13. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 16.--19. 1. "MLPL_AT_SP12,Memory Low Power Level (MLPL) at Setpoint 12. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0xC 12.--15. 1. "MLPL_AT_SP11,Memory Low Power Level (MLPL) at Setpoint 11. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 8.--11. 1. "MLPL_AT_SP10,Memory Low Power Level (MLPL) at Setpoint 10. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 4.--7. 1. "MLPL_AT_SP9,Memory Low Power Level (MLPL) at Setpoint 9. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 0.--3. 1. "MLPL_AT_SP8,Memory Low Power Level (MLPL) at Setpoint 8. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." tree.end tree "PGMC_CPC1" base ad:0x40C89400 group.long 0x4++0x3 line.long 0x0 "CPC_AUTHEN_CTRL,CPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0,1" bitfld.long 0x0 0. "USER,Allow user mode access" "0,1" group.long 0x10++0x7 line.long 0x0 "CPC_CORE_MODE,CPC Core Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,?,?" line.long 0x4 "CPC_CORE_POWER_CTRL,CPC core power control" bitfld.long 0x4 11. "ISO_OFF_SOFT,Software isolation off trigger" "0,1" bitfld.long 0x4 10. "PSW_ON_SOFT,Software power on trigger" "0,1" bitfld.long 0x4 9. "PSW_OFF_SOFT,Software power off trigger" "0,1" bitfld.long 0x4 8. "ISO_ON_SOFT,Software isolation on trigger" "0,1" newline bitfld.long 0x4 3. "PWR_OFF_AT_SUSPEND,Power off when domain enters SUSPEND mode" "0,1" bitfld.long 0x4 2. "PWR_OFF_AT_STOP,Power off when domain enters STOP mode" "0,1" bitfld.long 0x4 1. "PWR_OFF_AT_WAIT,Power off when domain enters WAIT mode" "0,1" group.long 0x2C++0x3 line.long 0x0 "CPC_FLAG,CPC flag" eventfld.long 0x0 0. "CORE_PDN_FLAG,set to 1 after core power switch off cleared by writing 1" "0,1" group.long 0x40++0xF line.long 0x0 "CPC_CACHE_MODE,CPC Cache Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "CPC_CACHE_CM_CTRL,CPC cache CPU mode control" bitfld.long 0x4 16. "MLPL_SOFT,Memory Low Power Level (MLPL) software change request keep 1 until MLPL transition complete" "0,1" hexmask.long.byte 0x4 12.--15. 1. "MLPL_AT_SUSPEND,Memory Low Power Level (MLPL) at SUSPEND mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 8.--11. 1. "MLPL_AT_STOP,Memory Low Power Level (MLPL) at STOP mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 4.--7. 1. "MLPL_AT_WAIT,Memory Low Power Level (MLPL) at WAIT mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x4 0.--3. 1. "MLPL_AT_RUN,Memory Low Power Level (MLPL) at RUN mode" line.long 0x8 "CPC_CACHE_SP_CTRL_0,CPC cache Setpoint control 0" hexmask.long.byte 0x8 28.--31. 1. "MLPL_AT_SP7,Memory Low Power Level (MLPL) at Setpoint 7. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 24.--27. 1. "MLPL_AT_SP6,Memory Low Power Level (MLPL) at Setpoint 6. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 20.--23. 1. "MLPL_AT_SP5,Memory Low Power Level (MLPL) at Setpoint 5. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 16.--19. 1. "MLPL_AT_SP4,Memory Low Power Level (MLPL) at Setpoint 4. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x8 12.--15. 1. "MLPL_AT_SP3,Memory Low Power Level (MLPL) at Setpoint 3. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 8.--11. 1. "MLPL_AT_SP2,Memory Low Power Level (MLPL) at Setpoint 2. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 4.--7. 1. "MLPL_AT_SP1,Memory Low Power Level (MLPL) at Setpoint 1. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 0.--3. 1. "MLPL_AT_SP0,Memory Low Power Level (MLPL) at Setpoint 0. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." line.long 0xC "CPC_CACHE_SP_CTRL_1,CPC cache Setpoint control 1" hexmask.long.byte 0xC 28.--31. 1. "MLPL_AT_SP15,Memory Low Power Level (MLPL) at Setpoint 15. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 24.--27. 1. "MLPL_AT_SP14,Memory Low Power Level (MLPL) at Setpoint 14. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 20.--23. 1. "MLPL_AT_SP13,Memory Low Power Level (MLPL) at Setpoint 13. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 16.--19. 1. "MLPL_AT_SP12,Memory Low Power Level (MLPL) at Setpoint 12. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0xC 12.--15. 1. "MLPL_AT_SP11,Memory Low Power Level (MLPL) at Setpoint 11. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 8.--11. 1. "MLPL_AT_SP10,Memory Low Power Level (MLPL) at Setpoint 10. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 4.--7. 1. "MLPL_AT_SP9,Memory Low Power Level (MLPL) at Setpoint 9. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 0.--3. 1. "MLPL_AT_SP8,Memory Low Power Level (MLPL) at Setpoint 8. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." group.long 0xC0++0xF line.long 0x0 "CPC_LMEM_MODE,CPC local memory Mode" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint,?" line.long 0x4 "CPC_LMEM_CM_CTRL,CPC local memory CPU mode control" bitfld.long 0x4 16. "MLPL_SOFT,Memory Low Power Level (MLPL) software change request keep 1 until MLPL transition complete" "0,1" hexmask.long.byte 0x4 12.--15. 1. "MLPL_AT_SUSPEND,Memory Low Power Level (MLPL) at SUSPEND mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 8.--11. 1. "MLPL_AT_STOP,Memory Low Power Level (MLPL) at STOP mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x4 4.--7. 1. "MLPL_AT_WAIT,Memory Low Power Level (MLPL) at WAIT mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x4 0.--3. 1. "MLPL_AT_RUN,Memory Low Power Level (MLPL) at RUN mode" line.long 0x8 "CPC_LMEM_SP_CTRL_0,CPC local memory Setpoint control 0" hexmask.long.byte 0x8 28.--31. 1. "MLPL_AT_SP7,Memory Low Power Level (MLPL) at Setpoint 7. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 24.--27. 1. "MLPL_AT_SP6,Memory Low Power Level (MLPL) at Setpoint 6. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 20.--23. 1. "MLPL_AT_SP5,Memory Low Power Level (MLPL) at Setpoint 5. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 16.--19. 1. "MLPL_AT_SP4,Memory Low Power Level (MLPL) at Setpoint 4. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0x8 12.--15. 1. "MLPL_AT_SP3,Memory Low Power Level (MLPL) at Setpoint 3. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 8.--11. 1. "MLPL_AT_SP2,Memory Low Power Level (MLPL) at Setpoint 2. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 4.--7. 1. "MLPL_AT_SP1,Memory Low Power Level (MLPL) at Setpoint 1. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0x8 0.--3. 1. "MLPL_AT_SP0,Memory Low Power Level (MLPL) at Setpoint 0. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." line.long 0xC "CPC_LMEM_SP_CTRL_1,CPC local memory Setpoint control 1" hexmask.long.byte 0xC 28.--31. 1. "MLPL_AT_SP15,Memory Low Power Level (MLPL) at Setpoint 15. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 24.--27. 1. "MLPL_AT_SP14,Memory Low Power Level (MLPL) at Setpoint 14. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 20.--23. 1. "MLPL_AT_SP13,Memory Low Power Level (MLPL) at Setpoint 13. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 16.--19. 1. "MLPL_AT_SP12,Memory Low Power Level (MLPL) at Setpoint 12. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." newline hexmask.long.byte 0xC 12.--15. 1. "MLPL_AT_SP11,Memory Low Power Level (MLPL) at Setpoint 11. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 8.--11. 1. "MLPL_AT_SP10,Memory Low Power Level (MLPL) at Setpoint 10. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 4.--7. 1. "MLPL_AT_SP9,Memory Low Power Level (MLPL) at Setpoint 9. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.byte 0xC 0.--3. 1. "MLPL_AT_SP8,Memory Low Power Level (MLPL) at Setpoint 8. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." tree.end tree.end tree "PGMC_MIF" base ad:0x0 tree "PGMC_CPC0_MIF0" base ad:0x40C89100 group.long 0x4++0x3 line.long 0x0 "MIF_AUTHEN_CTRL,MIF Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" group.long 0x10++0x3 line.long 0x0 "MIF_MLPL_SLEEP,MIF MLPL control of SLEEP" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x20++0x3 line.long 0x0 "MIF_MLPL_IG,MIF MLPL control of IG" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x30++0x3 line.long 0x0 "MIF_MLPL_LS,MIF MLPL control of LS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x40++0x3 line.long 0x0 "MIF_MLPL_HS,MIF MLPL control of HS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x50++0x3 line.long 0x0 "MIF_MLPL_STDBY,MIF MLPL control of STDBY" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x60++0x3 line.long 0x0 "MIF_MLPL_ARR_PDN,MIF MLPL control of array power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x70++0x3 line.long 0x0 "MIF_MLPL_PER_PDN,MIF MLPL control of peripheral power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x80++0x3 line.long 0x0 "MIF_MLPL_INITN,MIF MLPL control of INITN" bitfld.long 0x0 31. "BYPASS_VDD_OK,Bypass vdd_ok. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0xB0++0x3 line.long 0x0 "MIF_MLPL_ISO,MIF MLPL control of isolation enable" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" tree.end tree "PGMC_CPC0_MIF1" base ad:0x40C89200 group.long 0x4++0x3 line.long 0x0 "MIF_AUTHEN_CTRL,MIF Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" group.long 0x10++0x3 line.long 0x0 "MIF_MLPL_SLEEP,MIF MLPL control of SLEEP" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x20++0x3 line.long 0x0 "MIF_MLPL_IG,MIF MLPL control of IG" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x30++0x3 line.long 0x0 "MIF_MLPL_LS,MIF MLPL control of LS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x40++0x3 line.long 0x0 "MIF_MLPL_HS,MIF MLPL control of HS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x50++0x3 line.long 0x0 "MIF_MLPL_STDBY,MIF MLPL control of STDBY" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x60++0x3 line.long 0x0 "MIF_MLPL_ARR_PDN,MIF MLPL control of array power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x70++0x3 line.long 0x0 "MIF_MLPL_PER_PDN,MIF MLPL control of peripheral power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x80++0x3 line.long 0x0 "MIF_MLPL_INITN,MIF MLPL control of INITN" bitfld.long 0x0 31. "BYPASS_VDD_OK,Bypass vdd_ok. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0xB0++0x3 line.long 0x0 "MIF_MLPL_ISO,MIF MLPL control of isolation enable" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" tree.end tree "PGMC_CPC1_MIF0" base ad:0x40C89500 group.long 0x4++0x3 line.long 0x0 "MIF_AUTHEN_CTRL,MIF Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" group.long 0x10++0x3 line.long 0x0 "MIF_MLPL_SLEEP,MIF MLPL control of SLEEP" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x20++0x3 line.long 0x0 "MIF_MLPL_IG,MIF MLPL control of IG" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x30++0x3 line.long 0x0 "MIF_MLPL_LS,MIF MLPL control of LS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x40++0x3 line.long 0x0 "MIF_MLPL_HS,MIF MLPL control of HS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x50++0x3 line.long 0x0 "MIF_MLPL_STDBY,MIF MLPL control of STDBY" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x60++0x3 line.long 0x0 "MIF_MLPL_ARR_PDN,MIF MLPL control of array power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x70++0x3 line.long 0x0 "MIF_MLPL_PER_PDN,MIF MLPL control of peripheral power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x80++0x3 line.long 0x0 "MIF_MLPL_INITN,MIF MLPL control of INITN" bitfld.long 0x0 31. "BYPASS_VDD_OK,Bypass vdd_ok. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0xB0++0x3 line.long 0x0 "MIF_MLPL_ISO,MIF MLPL control of isolation enable" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" tree.end tree "PGMC_CPC1_MIF1" base ad:0x40C89600 group.long 0x4++0x3 line.long 0x0 "MIF_AUTHEN_CTRL,MIF Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" group.long 0x10++0x3 line.long 0x0 "MIF_MLPL_SLEEP,MIF MLPL control of SLEEP" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x20++0x3 line.long 0x0 "MIF_MLPL_IG,MIF MLPL control of IG" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x30++0x3 line.long 0x0 "MIF_MLPL_LS,MIF MLPL control of LS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x40++0x3 line.long 0x0 "MIF_MLPL_HS,MIF MLPL control of HS" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x50++0x3 line.long 0x0 "MIF_MLPL_STDBY,MIF MLPL control of STDBY" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x60++0x3 line.long 0x0 "MIF_MLPL_ARR_PDN,MIF MLPL control of array power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x70++0x3 line.long 0x0 "MIF_MLPL_PER_PDN,MIF MLPL control of peripheral power down" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0x80++0x3 line.long 0x0 "MIF_MLPL_INITN,MIF MLPL control of INITN" bitfld.long 0x0 31. "BYPASS_VDD_OK,Bypass vdd_ok. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" group.long 0xB0++0x3 line.long 0x0 "MIF_MLPL_ISO,MIF MLPL control of isolation enable" hexmask.long.word 0x0 0.--15. 1. "MLPL_CTRL,Signal behavior at each MLPL" tree.end tree.end tree "PGMC_PPC" base ad:0x40C8B000 group.long 0x4++0x3 line.long 0x0 "PPC_AUTHEN_CTRL,PPC Authentication Control" bitfld.long 0x0 20. "LOCK_CFG,Configuration lock" "0,1" bitfld.long 0x0 12. "LOCK_LIST,White list lock" "0,1" hexmask.long.byte 0x0 8.--11. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 4. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" bitfld.long 0x0 1. "NONSECURE,Allow non-secure mode access" "0,1" bitfld.long 0x0 0. "USER,Allow user mode access" "0,1" group.long 0x10++0xB line.long 0x0 "PPC_MODE,PPC Mode" bitfld.long 0x0 4.--5. "DOMAIN_ASSIGN,Domain assignment of the BPC" "0: Domain 0,1: Domain 1,2: Domain 2,3: Domain 3" bitfld.long 0x0 0.--1. "CTRL_MODE,Control mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0: Not affected by any low power mode,1: Controlled by CPU power mode of the domain,2: Controlled by Setpoint and system standby,?" line.long 0x4 "PPC_STBY_CM_CTRL,PPC standby CPU mode control" bitfld.long 0x4 9. "STBY_OFF_SOFT,Software PMIC standby off trigger" "0,1" bitfld.long 0x4 8. "STBY_ON_SOFT,Software PMIC standby on trigger" "0,1" bitfld.long 0x4 3. "STBY_ON_AT_SUSPEND,PMIC Standby on when domain enters SUSPEND mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" newline bitfld.long 0x4 2. "STBY_ON_AT_STOP,PMIC Standby on when domain enters STOP mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" bitfld.long 0x4 1. "STBY_ON_AT_WAIT,PMIC Standby on when domain enters WAIT mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." "0,1" line.long 0x8 "PPC_STBY_SP_CTRL,PPC standby Setpoint control" hexmask.long.word 0x8 16.--31. 1. "STBY_ON_AT_SP_SLEEP,PMIC standby on when system enters Setpoint number and system is in standby mode. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." hexmask.long.word 0x8 0.--15. 1. "STBY_ON_AT_SP_ACTIVE,PMIC standby on when system enters Setpoint number. This field is locked by AUTHEN_CTRL[LOCK_CFG] field." tree.end tree "PHY_LDO" base ad:0x0 group.long 0x0++0xF line.long 0x0 "CTRL0,Analog Control Register CTRL0" bitfld.long 0x0 15. "LINREG_PHY_ISO_B,Isolation control for attached PHY load" "0,1" hexmask.long.byte 0x0 4.--8. 1. "LINREG_OUTPUT_TRG,LinReg output voltage target setting" bitfld.long 0x0 2. "LINREG_ILIMIT_EN,LinReg current-limit enable" "0,1" bitfld.long 0x0 1. "LINREG_PWRUPLOAD_DIS,LinReg power-up load disable" "0: Internal pull-down enabled,1: Internal pull-down disabled" bitfld.long 0x0 0. "LINREG_EN,LinrReg master enable" "0,1" line.long 0x4 "CTRL0_SET,Analog Control Register CTRL0" bitfld.long 0x4 15. "LINREG_PHY_ISO_B,Isolation control for attached PHY load" "0,1" hexmask.long.byte 0x4 4.--8. 1. "LINREG_OUTPUT_TRG,LinReg output voltage target setting" bitfld.long 0x4 2. "LINREG_ILIMIT_EN,LinReg current-limit enable" "0,1" bitfld.long 0x4 1. "LINREG_PWRUPLOAD_DIS,LinReg power-up load disable" "0,1" bitfld.long 0x4 0. "LINREG_EN,LinrReg master enable" "0,1" line.long 0x8 "CTRL0_CLR,Analog Control Register CTRL0" eventfld.long 0x8 15. "LINREG_PHY_ISO_B,Isolation control for attached PHY load" "0,1" hexmask.long.byte 0x8 4.--8. 1. "LINREG_OUTPUT_TRG,LinReg output voltage target setting" eventfld.long 0x8 2. "LINREG_ILIMIT_EN,LinReg current-limit enable" "0,1" eventfld.long 0x8 1. "LINREG_PWRUPLOAD_DIS,LinReg power-up load disable" "0,1" eventfld.long 0x8 0. "LINREG_EN,LinrReg master enable" "0,1" line.long 0xC "CTRL0_TOG,Analog Control Register CTRL0" bitfld.long 0xC 15. "LINREG_PHY_ISO_B,Isolation control for attached PHY load" "0,1" hexmask.long.byte 0xC 4.--8. 1. "LINREG_OUTPUT_TRG,LinReg output voltage target setting" bitfld.long 0xC 2. "LINREG_ILIMIT_EN,LinReg current-limit enable" "0,1" bitfld.long 0xC 1. "LINREG_PWRUPLOAD_DIS,LinReg power-up load disable" "0,1" bitfld.long 0xC 0. "LINREG_EN,LinrReg master enable" "0,1" rgroup.long 0x50++0xF line.long 0x0 "STAT0,Analog Status Register STAT0" hexmask.long.byte 0x0 0.--3. 1. "LINREG_STAT,LinReg Status Bits" line.long 0x4 "STAT0_SET,Analog Status Register STAT0" hexmask.long.byte 0x4 0.--3. 1. "LINREG_STAT,LinReg Status Bits" line.long 0x8 "STAT0_CLR,Analog Status Register STAT0" hexmask.long.byte 0x8 0.--3. 1. "LINREG_STAT,LinReg Status Bits" line.long 0xC "STAT0_TOG,Analog Status Register STAT0" hexmask.long.byte 0xC 0.--3. 1. "LINREG_STAT,LinReg Status Bits" tree.end tree "PIT" base ad:0x0 tree "PIT1" base ad:0x400D8000 group.long 0x0++0x3 line.long 0x0 "MCR,PIT Module Control Register" bitfld.long 0x0 1. "MDIS,Module Disable for PIT" "0: Clock for standard PIT timers is enabled.,1: Clock for standard PIT timers is disabled." bitfld.long 0x0 0. "FRZ,Freeze" "0: Timers continue to run in Debug mode.,1: Timers are stopped in Debug mode." rgroup.long 0xE0++0x7 line.long 0x0 "LTMR64H,PIT Upper Lifetime Timer Register" hexmask.long 0x0 0.--31. 1. "LTH,Life Timer value" line.long 0x4 "LTMR64L,PIT Lower Lifetime Timer Register" hexmask.long 0x4 0.--31. 1. "LTL,Life Timer value" repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x400D8100 ad:0x400D8110 ad:0x400D8120 ad:0x400D8130) tree "TIMER[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "LDVAL,Timer Load Value Register" hexmask.long 0x0 0.--31. 1. "TSV,Timer Start Value" rgroup.long ($2+0x4)++0x3 line.long 0x0 "CVAL,Current Timer Value Register" hexmask.long 0x0 0.--31. 1. "TVL,Current Timer Value" group.long ($2+0x8)++0x7 line.long 0x0 "TCTRL,Timer Control Register" bitfld.long 0x0 2. "CHN,Chain Mode" "0: Timer is not chained.,1: Timer is chained to a previous timer. For.." bitfld.long 0x0 1. "TIE,Timer Interrupt Enable" "0: Interrupt requests from Timer n are disabled.,1: Interrupt is requested whenever TIF is set." bitfld.long 0x0 0. "TEN,Timer Enable" "0: Timer n is disabled.,1: Timer n is enabled." line.long 0x4 "TFLG,Timer Flag Register" eventfld.long 0x4 0. "TIF,Timer Interrupt Flag" "0: Timeout has not yet occurred.,1: Timeout has occurred." tree.end repeat.end tree.end tree "PIT2" base ad:0x40CB0000 group.long 0x0++0x3 line.long 0x0 "MCR,PIT Module Control Register" bitfld.long 0x0 1. "MDIS,Module Disable for PIT" "0: Clock for standard PIT timers is enabled.,1: Clock for standard PIT timers is disabled." bitfld.long 0x0 0. "FRZ,Freeze" "0: Timers continue to run in Debug mode.,1: Timers are stopped in Debug mode." rgroup.long 0xE0++0x7 line.long 0x0 "LTMR64H,PIT Upper Lifetime Timer Register" hexmask.long 0x0 0.--31. 1. "LTH,Life Timer value" line.long 0x4 "LTMR64L,PIT Lower Lifetime Timer Register" hexmask.long 0x4 0.--31. 1. "LTL,Life Timer value" repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40CB0100 ad:0x40CB0110 ad:0x40CB0120 ad:0x40CB0130) tree "TIMER[$1]" base $2 group.long ($2)++0x3 line.long 0x0 "LDVAL,Timer Load Value Register" hexmask.long 0x0 0.--31. 1. "TSV,Timer Start Value" rgroup.long ($2+0x4)++0x3 line.long 0x0 "CVAL,Current Timer Value Register" hexmask.long 0x0 0.--31. 1. "TVL,Current Timer Value" group.long ($2+0x8)++0x7 line.long 0x0 "TCTRL,Timer Control Register" bitfld.long 0x0 2. "CHN,Chain Mode" "0: Timer is not chained.,1: Timer is chained to a previous timer. For.." bitfld.long 0x0 1. "TIE,Timer Interrupt Enable" "0: Interrupt requests from Timer n are disabled.,1: Interrupt is requested whenever TIF is set." bitfld.long 0x0 0. "TEN,Timer Enable" "0: Timer n is disabled.,1: Timer n is enabled." line.long 0x4 "TFLG,Timer Flag Register" eventfld.long 0x4 0. "TIF,Timer Interrupt Flag" "0: Timeout has not yet occurred.,1: Timeout has occurred." tree.end repeat.end tree.end tree.end tree "PUF" base ad:0x40C82000 group.long 0x0++0xB line.long 0x0 "CTRL,PUF Control Register" bitfld.long 0x0 6. "GETKEY,Begin Get Key operation" "0: No Get Key operation in progress,1: Get Key operation in progress" newline bitfld.long 0x0 4. "SETKEY,Begin Set User Key operation" "0: No Set Key operation in progress,1: Set Key operation in progress" newline bitfld.long 0x0 3. "GENERATEKEY,Begin Set Intrinsic Key operation" "0: No Set Intrinsic Key operation in progress,1: Set Intrinsic Key operation in progress" newline bitfld.long 0x0 2. "START,Begin Start operation" "0: No Start operation in progress,1: Start operation in progress" newline bitfld.long 0x0 1. "ENROLL,Begin Enroll operation" "0: No Enroll operation in progress,1: Enroll operation in progress" newline bitfld.long 0x0 0. "ZEROIZE,Begin Zeroize operation for PUF and go to Error state" "0: No Zeroize operation in progress,1: Zeroize operation in progress" line.long 0x4 "KEYINDEX,PUF Key Index Register" hexmask.long.byte 0x4 0.--3. 1. "KEYIDX,PUF Key Index" line.long 0x8 "KEYSIZE,PUF Key Size Register" hexmask.long.byte 0x8 0.--5. 1. "KEYSIZE,PUF Key Size" rgroup.long 0x20++0x3 line.long 0x0 "STAT,PUF Status Register" bitfld.long 0x0 7. "CODEOUTAVAIL,CO_or" "0: Next part of Activation Code/Key Code is not..,1: Next part of Activation Code/Key Code is.." newline bitfld.long 0x0 6. "CODEINREQ,CI_ir" "0: No request for next part of Activation Code/Key..,1: request for next part of Activation Code/Key.." newline bitfld.long 0x0 5. "KEYOUTAVAIL,KO_or" "0: Next part of key is not available,1: Next part of key is available in KEYOUTPUT.." newline bitfld.long 0x0 4. "KEYINREQ,KI_ir" "0: No request for next part of key,1: Request for next part of key in KEYINPUT register" newline bitfld.long 0x0 2. "ERROR,puf_error" "0: PUF is not in the Error state,1: PUF is in the Error state" newline bitfld.long 0x0 1. "SUCCESS,puf_ok" "0: Last operation was unsuccessful,1: Last operation was successful" newline bitfld.long 0x0 0. "BUSY,puf_busy" "0: IDLE,1: BUSY" rgroup.long 0x28++0x3 line.long 0x0 "ALLOW,PUF Allow Register" bitfld.long 0x0 3. "ALLOWGETKEY,Allow Get Key operation" "0: Specified operation is not currently allowed,1: Specified operation is allowed" newline bitfld.long 0x0 2. "ALLOWSETKEY,Allow Set Key operations" "0: Specified operation is not currently allowed,1: Specified operation is allowed" newline bitfld.long 0x0 1. "ALLOWSTART,Allow Start operation" "0: Specified operation is not currently allowed,1: Specified operation is allowed" newline bitfld.long 0x0 0. "ALLOWENROLL,Allow Enroll operation" "0: Specified operation is not currently allowed,1: Specified operation is allowed" wgroup.long 0x40++0x7 line.long 0x0 "KEYINPUT,PUF Key Input Register" hexmask.long 0x0 0.--31. 1. "KEYIN,Key input data" line.long 0x4 "CODEINPUT,PUF Code Input Register" hexmask.long 0x4 0.--31. 1. "CODEIN,AC/KC input data" rgroup.long 0x48++0x3 line.long 0x0 "CODEOUTPUT,PUF Code Output Register" hexmask.long 0x0 0.--31. 1. "CODEOUT,AC/KC output data" rgroup.long 0x60++0x7 line.long 0x0 "KEYOUTINDEX,PUF Key Output Index Register" hexmask.long 0x0 0.--31. 1. "KEYOUTIDX,Output Key index" line.long 0x4 "KEYOUTPUT,PUF Key Output Register" hexmask.long 0x4 0.--31. 1. "KEYOUT,Key output data from a Get Key operation" group.long 0xDC++0x3 line.long 0x0 "IFSTAT,PUF Interface Status Register" eventfld.long 0x0 0. "ERROR,APB error has occurred" "0: NOERROR,1: ERROR" rgroup.long 0xFC++0x3 line.long 0x0 "VERSION,PUF Version Register" hexmask.long 0x0 0.--31. 1. "VERSION,Version of PUF" group.long 0x100++0xF line.long 0x0 "INTEN,PUF Interrupt Enable" bitfld.long 0x0 7. "CODEOUTAVAILEN,PUF Code Output Register Interrupt Enable" "0: AC/KC available interrupt disabled,1: AC/KC available interrupt enabled" newline bitfld.long 0x0 6. "CODEINREQEN,PUF Code Input Register Interrupt Enable" "0: AC/KC interrupt request disabled,1: AC/KC interrupt request enabled" newline bitfld.long 0x0 5. "KEYOUTAVAILEN,PUF Key Output Register Interrupt Enable" "0: Key available interrupt disabled,1: Key available interrupt enabled" newline bitfld.long 0x0 4. "KEYINREQEN,PUF Key Input Register Interrupt Enable" "0: Key interrupt request disabled,1: Key interrupt request enabled" newline bitfld.long 0x0 2. "ERROREN,PUF Error Interrupt Enable" "0: PUF error interrupt disabled,1: PUF error interrupt enabled" newline bitfld.long 0x0 1. "SUCCESSEN,PUF_OK Interrupt Enable" "0: PUF successful interrupt disabled,1: PUF successful interrupt enabled" newline bitfld.long 0x0 0. "READYEN,PUF Ready Interrupt Enable" "0: PUF ready interrupt disabled,1: PUF ready interrupt enabled" line.long 0x4 "INTSTAT,PUF Interrupt Status" rbitfld.long 0x4 7. "CODEOUTAVAIL,PUF Code Output Register Interrupt Status" "0: Next part of AC/KC is not available,1: Next part of AC/KC is available" newline rbitfld.long 0x4 6. "CODEINREQ,PUF Code Input Register Interrupt Status" "0: No request for next part of AC/KC,1: Request for next part of AC/KC" newline rbitfld.long 0x4 5. "KEYOUTAVAIL,PUF Key Output Register Interrupt Status" "0: Next part of key is not available,1: Next part of key is available" newline rbitfld.long 0x4 4. "KEYINREQ,PUF Key Input Register Interrupt Status" "0: No request for next part of key,1: Request for next part of key" newline rbitfld.long 0x4 2. "ERROR,PUF_ERROR Interrupt Status" "0: PUF is not in the Error state and operations can..,1: PUF is in the Error state and no operations can.." newline rbitfld.long 0x4 1. "SUCCESS,PUF_OK Interrupt Status" "0: Indicates that last operation was not successful,1: Indicates that last operation was successful" newline eventfld.long 0x4 0. "READY,PUF_FINISH Interrupt Status" "0: Indicates that last operation not finished,1: Indicates that last operation is finished" line.long 0x8 "PWRCTRL,PUF Power Control Of RAM" hexmask.long.byte 0x8 4.--7. 1. "RAM_PSW,PUF RAM power switches" newline bitfld.long 0x8 3. "RAM_INITN,RAM initialization" "0: Reset the PUF RAM (PUF operation disabled),1: Do not reset the PUF RAM (normal PUF operation.." newline bitfld.long 0x8 2. "CK_DIS,Clock disable" "0: PUF RAM is clocked (normal PUF operation enabled),1: PUF RAM clock is gated/disabled (PUF operation.." newline bitfld.long 0x8 0. "RAM_ON,PUF RAM on" "0: PUF RAM is in sleep mode (PUF operation disabled),1: PUF RAM is awake (normal PUF operation enabled)" line.long 0xC "CFG,PUF Configuration Register" bitfld.long 0xC 1. "PUF_BLOCK_ENROLL,PUF Block Enroll Disable" "0: Enable the Enrollment state,1: Disable the Enrollment state" newline bitfld.long 0xC 0. "PUF_BLOCK_SET_KEY,PUF Block Set Key Disable" "0: Enable the Set Key state,1: Disable the Set Key state" group.long 0x200++0x1B line.long 0x0 "KEYLOCK,PUF Key Manager Lock" bitfld.long 0x0 2.--3. "LOCK1,Lock Block 1" "0: OTFAD Key block locked,1: OTFAD Key block locked,2: OTFAD Key block unlocked,3: OTFAD Key block locked" newline bitfld.long 0x0 0.--1. "LOCK0,Lock Block 0" "0: SNVS Key block locked,1: SNVS Key block locked,2: SNVS Key block unlocked,3: SNVS Key block locked" line.long 0x4 "KEYENABLE,PUF Key Manager Enable" bitfld.long 0x4 2.--3. "ENABLE1,Enable Block 1" "0: Key block 1 disabled,1: Key block 1 disabled,2: Key block 1 enabled,3: Key block 1 disabled" newline bitfld.long 0x4 0.--1. "ENABLE0,Enable Block 0" "0: Key block 0 disabled,1: Key block 0 disabled,2: Key block 0 enabled,3: Key block 0 disabled" line.long 0x8 "KEYRESET,PUF Key Manager Reset" bitfld.long 0x8 2.--3. "RESET1,Reset Block 1" "0: Do not reset key block 1,1: Do not reset key block 1,2: Reset key block 1,3: Do not reset key block 1" newline bitfld.long 0x8 0.--1. "RESET0,Reset Block 0" "0: Do not reset key block 0,1: Do not reset key block 0,2: Reset key block 0,3: Do not reset key block 0" line.long 0xC "IDXBLK,PUF Index Block Key Output" bitfld.long 0xC 30.--31. "IDXBLK15,idxblk15" "0,1,2,3" newline bitfld.long 0xC 28.--29. "IDXBLK14,idxblk14" "0,1,2,3" newline bitfld.long 0xC 26.--27. "IDXBLK13,idxblk13" "0,1,2,3" newline bitfld.long 0xC 24.--25. "IDXBLK12,idxblk12" "0,1,2,3" newline bitfld.long 0xC 22.--23. "IDXBLK11,idxblk11" "0,1,2,3" newline bitfld.long 0xC 20.--21. "IDXBLK10,idxblk10" "0,1,2,3" newline bitfld.long 0xC 18.--19. "IDXBLK9,idxblk9" "0,1,2,3" newline bitfld.long 0xC 16.--17. "IDXBLK8,idxblk8" "0,1,2,3" newline bitfld.long 0xC 14.--15. "IDXBLK7,idxblk7" "0,1,2,3" newline bitfld.long 0xC 12.--13. "IDXBLK6,idxblk6" "0,1,2,3" newline bitfld.long 0xC 10.--11. "IDXBLK5,idxblk5" "0,1,2,3" newline bitfld.long 0xC 8.--9. "IDXBLK4,idxblk4" "0,1,2,3" newline bitfld.long 0xC 6.--7. "IDXBLK3,idxblk3" "0,1,2,3" newline bitfld.long 0xC 4.--5. "IDXBLK2,idxblk2" "0,1,2,3" newline bitfld.long 0xC 2.--3. "IDXBLK1,idxblk1" "0,1,2,3" newline bitfld.long 0xC 0.--1. "IDXBLK0,idxblk0" "0,1,2,3" line.long 0x10 "IDXBLK_DP,PUF Index Block Key Output" bitfld.long 0x10 30.--31. "IDXBLK_DP15,idxblk_dp15" "0,1,2,3" newline bitfld.long 0x10 28.--29. "IDXBLK_DP14,idxblk_dp14" "0,1,2,3" newline bitfld.long 0x10 26.--27. "IDXBLK_DP13,idxblk_dp13" "0,1,2,3" newline bitfld.long 0x10 24.--25. "IDXBLK_DP12,idxblk_dp12" "0,1,2,3" newline bitfld.long 0x10 22.--23. "IDXBLK_DP11,idxblk_dp11" "0,1,2,3" newline bitfld.long 0x10 20.--21. "IDXBLK_DP10,idxblk_dp10" "0,1,2,3" newline bitfld.long 0x10 18.--19. "IDXBLK_DP9,idxblk_dp9" "0,1,2,3" newline bitfld.long 0x10 16.--17. "IDXBLK_DP8,idxblk_dp8" "0,1,2,3" newline bitfld.long 0x10 14.--15. "IDXBLK_DP7,idxblk_dp7" "0,1,2,3" newline bitfld.long 0x10 12.--13. "IDXBLK_DP6,idxblk_dp6" "0,1,2,3" newline bitfld.long 0x10 10.--11. "IDXBLK_DP5,idxblk_dp5" "0,1,2,3" newline bitfld.long 0x10 8.--9. "IDXBLK_DP4,idxblk_dp4" "0,1,2,3" newline bitfld.long 0x10 6.--7. "IDXBLK_DP3,idxblk_dp3" "0,1,2,3" newline bitfld.long 0x10 4.--5. "IDXBLK_DP2,idxblk_dp2" "0,1,2,3" newline bitfld.long 0x10 2.--3. "IDXBLK_DP1,idxblk_dp1" "0,1,2,3" newline bitfld.long 0x10 0.--1. "IDXBLK_DP0,idxblk_dp0" "0,1,2,3" line.long 0x14 "KEYMASK0,PUF Key Block 0 Mask Enable" hexmask.long 0x14 0.--31. 1. "KEYMASK,KEYMASK0" line.long 0x18 "KEYMASK1,PUF Key Block 1 Mask Enable" hexmask.long 0x18 0.--31. 1. "KEYMASK,KEYMASK1" rgroup.long 0x254++0x7 line.long 0x0 "IDXBLK_STATUS,PUF Index Block Setting Status Register" bitfld.long 0x0 30.--31. "IDXBLK_STATUS15,idxblk_status15" "0,1,2,3" newline bitfld.long 0x0 28.--29. "IDXBLK_STATUS14,idxblk_status14" "0,1,2,3" newline bitfld.long 0x0 26.--27. "IDXBLK_STATUS13,idxblk_status13" "0,1,2,3" newline bitfld.long 0x0 24.--25. "IDXBLK_STATUS12,idxblk_status12" "0,1,2,3" newline bitfld.long 0x0 22.--23. "IDXBLK_STATUS11,idxblk_status11" "0,1,2,3" newline bitfld.long 0x0 20.--21. "IDXBLK_STATUS10,idxblk_status10" "0,1,2,3" newline bitfld.long 0x0 18.--19. "IDXBLK_STATUS9,idxblk_status9" "0,1,2,3" newline bitfld.long 0x0 16.--17. "IDXBLK_STATUS8,idxblk_status8" "0,1,2,3" newline bitfld.long 0x0 14.--15. "IDXBLK_STATUS7,idxblk_status7" "0,1,2,3" newline bitfld.long 0x0 12.--13. "IDXBLK_STATUS6,idxblk_status6" "0,1,2,3" newline bitfld.long 0x0 10.--11. "IDXBLK_STATUS5,idxblk_status5" "0,1,2,3" newline bitfld.long 0x0 8.--9. "IDXBLK_STATUS4,idxblk_status4" "0,1,2,3" newline bitfld.long 0x0 6.--7. "IDXBLK_STATUS3,idxblk_status3" "0,1,2,3" newline bitfld.long 0x0 4.--5. "IDXBLK_STATUS2,idxblk_status2" "0,1,2,3" newline bitfld.long 0x0 2.--3. "IDXBLK_STATUS1,idxblk_status1" "0,1,2,3" newline bitfld.long 0x0 0.--1. "IDXBLK_STATUS0,idxblk_status0" "0,1,2,3" line.long 0x4 "IDXBLK_SHIFT,PUF Key Manager Shift Status" hexmask.long.byte 0x4 4.--7. 1. "IND_KEY1,Index of key space in block 1" newline hexmask.long.byte 0x4 0.--3. 1. "IND_KEY0,Index of key space in block 0" tree.end tree "PWM" base ad:0x0 tree "PWM1" base ad:0x4018C000 repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x4018C000 ad:0x4018C060 ad:0x4018C0C0 ad:0x4018C120) tree "SM[$1]" base $2 rgroup.word ($2)++0x1 line.word 0x0 "SMCNT,Counter Register" hexmask.word 0x0 0.--15. 1. "CNT,Counter Register Bits" group.word ($2+0x2)++0x5 line.word 0x0 "SMINIT,Initial Count Register" hexmask.word 0x0 0.--15. 1. "INIT,Initial Count Register Bits" line.word 0x2 "SMCTRL2,Control 2 Register" bitfld.word 0x2 15. "DBGEN,Debug Enable" "0,1" bitfld.word 0x2 14. "WAITEN,WAIT Enable" "0,1" newline bitfld.word 0x2 13. "INDEP,Independent or Complementary Pair Operation" "0: PWM_A and PWM_B form a complementary PWM pair.,1: PWM_A and PWM_B outputs are independent PWMs." bitfld.word 0x2 12. "PWM23_INIT,PWM23 Initial Value" "0,1" newline bitfld.word 0x2 11. "PWM45_INIT,PWM45 Initial Value" "0,1" bitfld.word 0x2 10. "PWMX_INIT,PWM_X Initial Value" "0,1" newline bitfld.word 0x2 8.--9. "INIT_SEL,Initialization Control Select" "0: Local sync (PWM_X) causes initialization.,1: Master reload from submodule 0 causes..,2: Master sync from submodule 0 causes..,3: EXT_SYNC causes initialization." bitfld.word 0x2 7. "FRCEN,FRCEN" "0: Initialization from a FORCE_OUT is disabled.,1: Initialization from a FORCE_OUT is enabled." newline bitfld.word 0x2 6. "FORCE,Force Initialization" "0,1" bitfld.word 0x2 3.--5. "FORCE_SEL,This read/write bit determines the source of the FORCE OUTPUT signal for this submodule." "0: The local force signal CTRL2[FORCE] from this..,1: The master force signal from submodule 0 is used..,2: The local reload signal from this submodule is..,3: The master reload signal from submodule0 is used..,4: The local sync signal from this submodule is..,5: The master sync signal from submodule0 is used..,6: The external force signal EXT_FORCE from outside..,7: The external sync signal EXT_SYNC from outside.." newline bitfld.word 0x2 2. "RELOAD_SEL,Reload Source Select" "0: The local RELOAD signal is used to reload..,1: The master RELOAD signal (from submodule 0) is.." bitfld.word 0x2 0.--1. "CLK_SEL,Clock Source Select" "0: The IPBus clock is used as the clock for the..,1: EXT_CLK is used as the clock for the local..,2: Submodule 0's clock (AUX_CLK) is used as the..,?" line.word 0x4 "SMCTRL,Control Register" hexmask.word.byte 0x4 12.--15. 1. "LDFQ,Load Frequency" bitfld.word 0x4 11. "HALF,Half Cycle Reload" "0: Half-cycle reloads disabled.,1: Half-cycle reloads enabled." newline bitfld.word 0x4 10. "FULL,Full Cycle Reload" "0: Full-cycle reloads disabled.,1: Full-cycle reloads enabled." rbitfld.word 0x4 8.--9. "DT,Deadtime" "0,1,2,3" newline bitfld.word 0x4 7. "COMPMODE,Compare Mode" "0: The VAL* registers and the PWM counter are..,1: The VAL* registers and the PWM counter are.." bitfld.word 0x4 4.--6. "PRSC,Prescaler" "0: Prescaler 1,1: Prescaler 2,2: Prescaler 4,3: Prescaler 8,4: Prescaler 16,5: Prescaler 32,6: Prescaler 64,7: Prescaler 128" newline bitfld.word 0x4 3. "SPLIT,Split the DBLPWM signal to PWMA and PWMB" "0: DBLPWM is not split. PWMA and PWMB each have..,1: DBLPWM is split to PWMA and PWMB." bitfld.word 0x4 2. "LDMOD,Load Mode Select" "0: Buffered registers of this submodule are loaded..,1: Buffered registers of this submodule are loaded.." newline bitfld.word 0x4 1. "DBLX,PWMX Double Switching Enable" "0: PWMX double pulse disabled.,1: PWMX double pulse enabled." bitfld.word 0x4 0. "DBLEN,Double Switching Enable" "0: Double switching disabled.,1: Double switching enabled." group.word ($2+0xA)++0x23 line.word 0x0 "SMVAL0,Value Register 0" hexmask.word 0x0 0.--15. 1. "VAL0,Value Register 0" line.word 0x2 "SMFRACVAL1,Fractional Value Register 1" hexmask.word.byte 0x2 11.--15. 1. "FRACVAL1,Fractional Value 1 Register" line.word 0x4 "SMVAL1,Value Register 1" hexmask.word 0x4 0.--15. 1. "VAL1,Value Register 1" line.word 0x6 "SMFRACVAL2,Fractional Value Register 2" hexmask.word.byte 0x6 11.--15. 1. "FRACVAL2,Fractional Value 2" line.word 0x8 "SMVAL2,Value Register 2" hexmask.word 0x8 0.--15. 1. "VAL2,Value Register 2" line.word 0xA "SMFRACVAL3,Fractional Value Register 3" hexmask.word.byte 0xA 11.--15. 1. "FRACVAL3,Fractional Value 3" line.word 0xC "SMVAL3,Value Register 3" hexmask.word 0xC 0.--15. 1. "VAL3,Value Register 3" line.word 0xE "SMFRACVAL4,Fractional Value Register 4" hexmask.word.byte 0xE 11.--15. 1. "FRACVAL4,Fractional Value 4" line.word 0x10 "SMVAL4,Value Register 4" hexmask.word 0x10 0.--15. 1. "VAL4,Value Register 4" line.word 0x12 "SMFRACVAL5,Fractional Value Register 5" hexmask.word.byte 0x12 11.--15. 1. "FRACVAL5,Fractional Value 5" line.word 0x14 "SMVAL5,Value Register 5" hexmask.word 0x14 0.--15. 1. "VAL5,Value Register 5" line.word 0x16 "SMFRCTRL,Fractional Control Register" rbitfld.word 0x16 15. "TEST,Test Status Bit" "0,1" bitfld.word 0x16 4. "FRAC45_EN,Fractional Cycle Placement Enable for PWM_B" "0: Disable fractional cycle placement for PWM_B.,1: Enable fractional cycle placement for PWM_B." newline bitfld.word 0x16 2. "FRAC23_EN,Fractional Cycle Placement Enable for PWM_A" "0: Disable fractional cycle placement for PWM_A.,1: Enable fractional cycle placement for PWM_A." bitfld.word 0x16 1. "FRAC1_EN,Fractional Cycle PWM Period Enable" "0: Disable fractional cycle length for the PWM..,1: Enable fractional cycle length for the PWM period." line.word 0x18 "SMOCTRL,Output Control Register" rbitfld.word 0x18 15. "PWMA_IN,PWM_A Input" "0,1" rbitfld.word 0x18 14. "PWMB_IN,PWM_B Input" "0,1" newline rbitfld.word 0x18 13. "PWMX_IN,PWM_X Input" "0,1" bitfld.word 0x18 10. "POLA,PWM_A Output Polarity" "0: PWM_A output not inverted. A high level on the..,1: PWM_A output inverted. A low level on the PWM_A.." newline bitfld.word 0x18 9. "POLB,PWM_B Output Polarity" "0: PWM_B output not inverted. A high level on the..,1: PWM_B output inverted. A low level on the PWM_B.." bitfld.word 0x18 8. "POLX,PWM_X Output Polarity" "0: PWM_X output not inverted. A high level on the..,1: PWM_X output inverted. A low level on the PWM_X.." newline bitfld.word 0x18 4.--5. "PWMAFS,PWM_A Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." bitfld.word 0x18 2.--3. "PWMBFS,PWM_B Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." newline bitfld.word 0x18 0.--1. "PWMXFS,PWM_X Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." line.word 0x1A "SMSTS,Status Register" rbitfld.word 0x1A 14. "RUF,Registers Updated Flag" "0: No register update has occurred since last reload.,1: At least one of the double buffered registers.." eventfld.word 0x1A 13. "REF,Reload Error Flag" "0: No reload error occurred.,1: Reload signal occurred with non-coherent data.." newline eventfld.word 0x1A 12. "RF,Reload Flag" "0: No new reload cycle since last STS[RF] clearing,1: New reload cycle since last STS[RF] clearing" eventfld.word 0x1A 11. "CFA1,Capture Flag A1" "0,1" newline eventfld.word 0x1A 10. "CFA0,Capture Flag A0" "0,1" eventfld.word 0x1A 9. "CFB1,Capture Flag B1" "0,1" newline eventfld.word 0x1A 8. "CFB0,Capture Flag B0" "0,1" eventfld.word 0x1A 7. "CFX1,Capture Flag X1" "0,1" newline eventfld.word 0x1A 6. "CFX0,Capture Flag X0" "0,1" hexmask.word.byte 0x1A 0.--5. 1. "CMPF,Compare Flags" line.word 0x1C "SMINTEN,Interrupt Enable Register" bitfld.word 0x1C 13. "REIE,Reload Error Interrupt Enable" "0: STS[REF] CPU interrupt requests disabled,1: STS[REF] CPU interrupt requests enabled" bitfld.word 0x1C 12. "RIE,Reload Interrupt Enable" "0: STS[RF] CPU interrupt requests disabled,1: STS[RF] CPU interrupt requests enabled" newline bitfld.word 0x1C 11. "CA1IE,Capture A 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFA1].,1: Interrupt request enabled for STS[CFA1]." bitfld.word 0x1C 10. "CA0IE,Capture A 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFA0].,1: Interrupt request enabled for STS[CFA0]." newline bitfld.word 0x1C 9. "CB1IE,Capture B 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFB1].,1: Interrupt request enabled for STS[CFB1]." bitfld.word 0x1C 8. "CB0IE,Capture B 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFB0].,1: Interrupt request enabled for STS[CFB0]." newline bitfld.word 0x1C 7. "CX1IE,Capture X 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFX1].,1: Interrupt request enabled for STS[CFX1]." bitfld.word 0x1C 6. "CX0IE,Capture X 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFX0].,1: Interrupt request enabled for STS[CFX0]." newline hexmask.word.byte 0x1C 0.--5. 1. "CMPIE,Compare Interrupt Enables" line.word 0x1E "SMDMAEN,DMA Enable Register" bitfld.word 0x1E 9. "VALDE,Value Registers DMA Enable" "0: DMA write requests disabled,1: Enabled" bitfld.word 0x1E 8. "FAND,FIFO Watermark AND Control" "0: Selected FIFO watermarks are OR'ed together.,1: Selected FIFO watermarks are AND'ed together." newline bitfld.word 0x1E 6.--7. "CAPTDE,Capture DMA Enable Source Select" "0: Read DMA requests disabled.,1: Exceeding a FIFO watermark sets the DMA read..,2: A local sync (VAL1 matches counter) sets the..,3: A local reload (STS[RF] being set) sets the read.." bitfld.word 0x1E 5. "CA1DE,Capture A1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 4. "CA0DE,Capture A0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 3. "CB1DE,Capture B1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 2. "CB0DE,Capture B0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 1. "CX1DE,Capture X1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 0. "CX0DE,Capture X0 FIFO DMA Enable" "0,1" line.word 0x20 "SMTCTRL,Output Trigger Control Register" bitfld.word 0x20 15. "PWAOT0,Output Trigger 0 Source Select" "0: Route the PWM_OUT_TRIG0 signal to PWM_OUT_TRIG0..,1: Route the PWMA output to the PWM_OUT_TRIG0 port." bitfld.word 0x20 14. "PWBOT1,Output Trigger 1 Source Select" "0: Route the PWM_OUT_TRIG1 signal to PWM_OUT_TRIG1..,1: Route the PWMB output to the PWM_OUT_TRIG1 port." newline bitfld.word 0x20 12. "TRGFRQ,Trigger frequency" "0: Trigger outputs are generated during every PWM..,1: Trigger outputs are generated only during the.." hexmask.word.byte 0x20 0.--5. 1. "OUT_TRIG_EN,Output Trigger Enables" line.word 0x22 "SMDISMAP0,Fault Disable Mapping Register 0" hexmask.word.byte 0x22 8.--11. 1. "DIS0X,PWM_X Fault Disable Mask 0" hexmask.word.byte 0x22 4.--7. 1. "DIS0B,PWM_B Fault Disable Mask 0" newline hexmask.word.byte 0x22 0.--3. 1. "DIS0A,PWM_A Fault Disable Mask 0" group.word ($2+0x30)++0xF line.word 0x0 "SMDTCNT0,Deadtime Count Register 0" hexmask.word 0x0 0.--15. 1. "DTCNT0,DTCNT0" line.word 0x2 "SMDTCNT1,Deadtime Count Register 1" hexmask.word 0x2 0.--15. 1. "DTCNT1,DTCNT1" line.word 0x4 "SMCAPTCTRLA,Capture Control A Register" rbitfld.word 0x4 13.--15. "CA1CNT,Capture A1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x4 10.--12. "CA0CNT,Capture A0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x4 8.--9. "CFAWM,Capture A FIFOs Water Mark" "0,1,2,3" bitfld.word 0x4 7. "EDGCNTA_EN,Edge Counter A Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x4 6. "INP_SELA,Input Select A" "0: Raw PWM_A input signal selected as source.,1: Edge Counter" bitfld.word 0x4 4.--5. "EDGA1,Edge A 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x4 2.--3. "EDGA0,Edge A 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x4 1. "ONESHOTA,One Shot Mode A" "0: Free Running,1: One Shot" newline bitfld.word 0x4 0. "ARMA,Arm A" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0x6 "SMCAPTCOMPA,Capture Compare A Register" hexmask.word.byte 0x6 8.--15. 1. "EDGCNTA,Edge Counter A" hexmask.word.byte 0x6 0.--7. 1. "EDGCMPA,Edge Compare A" line.word 0x8 "SMCAPTCTRLB,Capture Control B Register" rbitfld.word 0x8 13.--15. "CB1CNT,Capture B1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x8 10.--12. "CB0CNT,Capture B0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x8 8.--9. "CFBWM,Capture B FIFOs Water Mark" "0,1,2,3" bitfld.word 0x8 7. "EDGCNTB_EN,Edge Counter B Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x8 6. "INP_SELB,Input Select B" "0: Raw PWM_B input signal selected as source.,1: Edge Counter" bitfld.word 0x8 4.--5. "EDGB1,Edge B 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x8 2.--3. "EDGB0,Edge B 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x8 1. "ONESHOTB,One Shot Mode B" "0: Free Running,1: One Shot" newline bitfld.word 0x8 0. "ARMB,Arm B" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xA "SMCAPTCOMPB,Capture Compare B Register" hexmask.word.byte 0xA 8.--15. 1. "EDGCNTB,Edge Counter B" hexmask.word.byte 0xA 0.--7. 1. "EDGCMPB,Edge Compare B" line.word 0xC "SMCAPTCTRLX,Capture Control X Register" rbitfld.word 0xC 13.--15. "CX1CNT,Capture X1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0xC 10.--12. "CX0CNT,Capture X0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0xC 8.--9. "CFXWM,Capture X FIFOs Water Mark" "0,1,2,3" bitfld.word 0xC 7. "EDGCNTX_EN,Edge Counter X Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0xC 6. "INP_SELX,Input Select X" "0: Raw PWM_X input signal selected as source.,1: Edge Counter" bitfld.word 0xC 4.--5. "EDGX1,Edge X 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0xC 2.--3. "EDGX0,Edge X 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0xC 1. "ONESHOTX,One Shot Mode Aux" "0: Free Running,1: One Shot" newline bitfld.word 0xC 0. "ARMX,Arm X" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xE "SMCAPTCOMPX,Capture Compare X Register" hexmask.word.byte 0xE 8.--15. 1. "EDGCNTX,Edge Counter X" hexmask.word.byte 0xE 0.--7. 1. "EDGCMPX,Edge Compare X" rgroup.word ($2+0x40)++0x17 line.word 0x0 "SMCVAL0,Capture Value 0 Register" hexmask.word 0x0 0.--15. 1. "CAPTVAL0,CAPTVAL0" line.word 0x2 "SMCVAL0CYC,Capture Value 0 Cycle Register" hexmask.word.byte 0x2 0.--3. 1. "CVAL0CYC,CVAL0CYC" line.word 0x4 "SMCVAL1,Capture Value 1 Register" hexmask.word 0x4 0.--15. 1. "CAPTVAL1,CAPTVAL1" line.word 0x6 "SMCVAL1CYC,Capture Value 1 Cycle Register" hexmask.word.byte 0x6 0.--3. 1. "CVAL1CYC,CVAL1CYC" line.word 0x8 "SMCVAL2,Capture Value 2 Register" hexmask.word 0x8 0.--15. 1. "CAPTVAL2,CAPTVAL2" line.word 0xA "SMCVAL2CYC,Capture Value 2 Cycle Register" hexmask.word.byte 0xA 0.--3. 1. "CVAL2CYC,CVAL2CYC" line.word 0xC "SMCVAL3,Capture Value 3 Register" hexmask.word 0xC 0.--15. 1. "CAPTVAL3,CAPTVAL3" line.word 0xE "SMCVAL3CYC,Capture Value 3 Cycle Register" hexmask.word.byte 0xE 0.--3. 1. "CVAL3CYC,CVAL3CYC" line.word 0x10 "SMCVAL4,Capture Value 4 Register" hexmask.word 0x10 0.--15. 1. "CAPTVAL4,CAPTVAL4" line.word 0x12 "SMCVAL4CYC,Capture Value 4 Cycle Register" hexmask.word.byte 0x12 0.--3. 1. "CVAL4CYC,CVAL4CYC" line.word 0x14 "SMCVAL5,Capture Value 5 Register" hexmask.word 0x14 0.--15. 1. "CAPTVAL5,CAPTVAL5" line.word 0x16 "SMCVAL5CYC,Capture Value 5 Cycle Register" hexmask.word.byte 0x16 0.--3. 1. "CVAL5CYC,CVAL5CYC" tree.end repeat.end base ad:0x4018C000 group.word 0x180++0x15 line.word 0x0 "OUTEN,Output Enable Register" hexmask.word.byte 0x0 8.--11. 1. "PWMA_EN,PWM_A Output Enables" hexmask.word.byte 0x0 4.--7. 1. "PWMB_EN,PWM_B Output Enables" newline hexmask.word.byte 0x0 0.--3. 1. "PWMX_EN,PWM_X Output Enables" line.word 0x2 "MASK,Mask Register" hexmask.word.byte 0x2 8.--11. 1. "MASKA,PWM_A Masks" hexmask.word.byte 0x2 4.--7. 1. "MASKB,PWM_B Masks" newline hexmask.word.byte 0x2 0.--3. 1. "MASKX,PWM_X Masks" line.word 0x4 "SWCOUT,Software Controlled Output Register" bitfld.word 0x4 7. "SM3OUT23,Submodule 3 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 6. "SM3OUT45,Submodule 3 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 5. "SM2OUT23,Submodule 2 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 4. "SM2OUT45,Submodule 2 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 3. "SM1OUT23,Submodule 1 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 2. "SM1OUT45,Submodule 1 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 1. "SM0OUT23,Submodule 0 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 0. "SM0OUT45,Submodule 0 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." line.word 0x6 "DTSRCSEL,PWM Source Select Register" bitfld.word 0x6 14.--15. "SM3SEL23,Submodule 3 PWM23 Control Select" "0: Generated SM3PWM23 signal is used by the..,1: Inverted generated SM3PWM23 signal is used by..,2: SWCOUT[SM3OUT23] is used by the deadtime logic.,3: PWM3_EXTA signal is used by the deadtime logic." bitfld.word 0x6 12.--13. "SM3SEL45,Submodule 3 PWM45 Control Select" "0: Generated SM3PWM45 signal is used by the..,1: Inverted generated SM3PWM45 signal is used by..,2: SWCOUT[SM3OUT45] is used by the deadtime logic.,3: PWM3_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 10.--11. "SM2SEL23,Submodule 2 PWM23 Control Select" "0: Generated SM2PWM23 signal is used by the..,1: Inverted generated SM2PWM23 signal is used by..,2: SWCOUT[SM2OUT23] is used by the deadtime logic.,3: PWM2_EXTA signal is used by the deadtime logic." bitfld.word 0x6 8.--9. "SM2SEL45,Submodule 2 PWM45 Control Select" "0: Generated SM2PWM45 signal is used by the..,1: Inverted generated SM2PWM45 signal is used by..,2: SWCOUT[SM2OUT45] is used by the deadtime logic.,3: PWM2_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 6.--7. "SM1SEL23,Submodule 1 PWM23 Control Select" "0: Generated SM1PWM23 signal is used by the..,1: Inverted generated SM1PWM23 signal is used by..,2: SWCOUT[SM1OUT23] is used by the deadtime logic.,3: PWM1_EXTA signal is used by the deadtime logic." bitfld.word 0x6 4.--5. "SM1SEL45,Submodule 1 PWM45 Control Select" "0: Generated SM1PWM45 signal is used by the..,1: Inverted generated SM1PWM45 signal is used by..,2: SWCOUT[SM1OUT45] is used by the deadtime logic.,3: PWM1_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 2.--3. "SM0SEL23,Submodule 0 PWM23 Control Select" "0: Generated SM0PWM23 signal is used by the..,1: Inverted generated SM0PWM23 signal is used by..,2: SWCOUT[SM0OUT23] is used by the deadtime logic.,3: PWM0_EXTA signal is used by the deadtime logic." bitfld.word 0x6 0.--1. "SM0SEL45,Submodule 0 PWM45 Control Select" "0: Generated SM0PWM45 signal is used by the..,1: Inverted generated SM0PWM45 signal is used by..,2: SWCOUT[SM0OUT45] is used by the deadtime logic.,3: PWM0_EXTB signal is used by the deadtime logic." line.word 0x8 "MCTRL,Master Control Register" hexmask.word.byte 0x8 12.--15. 1. "IPOL,Current Polarity" hexmask.word.byte 0x8 8.--11. 1. "RUN,Run" newline hexmask.word.byte 0x8 4.--7. 1. "CLDOK,Clear Load Okay" hexmask.word.byte 0x8 0.--3. 1. "LDOK,Load Okay" line.word 0xA "MCTRL2,Master Control 2 Register" bitfld.word 0xA 0.--1. "MONPLL,Monitor PLL State" "0: Not locked. Do not monitor PLL operation.,1: Not locked. Monitor PLL operation to..,2: Locked. Do not monitor PLL operation. Resetting..,3: Locked. Monitor PLL operation to automatically.." line.word 0xC "FCTRL0,Fault Control Register" hexmask.word.byte 0xC 12.--15. 1. "FLVL,Fault Level" hexmask.word.byte 0xC 8.--11. 1. "FAUTO,Automatic Fault Clearing" newline hexmask.word.byte 0xC 4.--7. 1. "FSAFE,Fault Safety Mode" hexmask.word.byte 0xC 0.--3. 1. "FIE,Fault Interrupt Enables" line.word 0xE "FSTS0,Fault Status Register" hexmask.word.byte 0xE 12.--15. 1. "FHALF,Half Cycle Fault Recovery" hexmask.word.byte 0xE 8.--11. 1. "FFPIN,Filtered Fault Pins" newline hexmask.word.byte 0xE 4.--7. 1. "FFULL,Full Cycle" hexmask.word.byte 0xE 0.--3. 1. "FFLAG,Fault Flags" line.word 0x10 "FFILT0,Fault Filter Register" bitfld.word 0x10 15. "GSTR,Fault Glitch Stretch Enable" "0: Fault input glitch stretching is disabled.,1: Input fault signals will be stretched to at.." bitfld.word 0x10 8.--10. "FILT_CNT,Fault Filter Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x10 0.--7. 1. "FILT_PER,Fault Filter Period" line.word 0x12 "FTST0,Fault Test Register" bitfld.word 0x12 0. "FTEST,Fault Test" "0: No fault,1: Cause a simulated fault" line.word 0x14 "FCTRL20,Fault Control 2 Register" hexmask.word.byte 0x14 0.--3. 1. "NOCOMB,No Combinational Path From Fault Input To PWM Output" tree.end tree "PWM2" base ad:0x40190000 repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40190000 ad:0x40190060 ad:0x401900C0 ad:0x40190120) tree "SM[$1]" base $2 rgroup.word ($2)++0x1 line.word 0x0 "SMCNT,Counter Register" hexmask.word 0x0 0.--15. 1. "CNT,Counter Register Bits" group.word ($2+0x2)++0x5 line.word 0x0 "SMINIT,Initial Count Register" hexmask.word 0x0 0.--15. 1. "INIT,Initial Count Register Bits" line.word 0x2 "SMCTRL2,Control 2 Register" bitfld.word 0x2 15. "DBGEN,Debug Enable" "0,1" bitfld.word 0x2 14. "WAITEN,WAIT Enable" "0,1" newline bitfld.word 0x2 13. "INDEP,Independent or Complementary Pair Operation" "0: PWM_A and PWM_B form a complementary PWM pair.,1: PWM_A and PWM_B outputs are independent PWMs." bitfld.word 0x2 12. "PWM23_INIT,PWM23 Initial Value" "0,1" newline bitfld.word 0x2 11. "PWM45_INIT,PWM45 Initial Value" "0,1" bitfld.word 0x2 10. "PWMX_INIT,PWM_X Initial Value" "0,1" newline bitfld.word 0x2 8.--9. "INIT_SEL,Initialization Control Select" "0: Local sync (PWM_X) causes initialization.,1: Master reload from submodule 0 causes..,2: Master sync from submodule 0 causes..,3: EXT_SYNC causes initialization." bitfld.word 0x2 7. "FRCEN,FRCEN" "0: Initialization from a FORCE_OUT is disabled.,1: Initialization from a FORCE_OUT is enabled." newline bitfld.word 0x2 6. "FORCE,Force Initialization" "0,1" bitfld.word 0x2 3.--5. "FORCE_SEL,This read/write bit determines the source of the FORCE OUTPUT signal for this submodule." "0: The local force signal CTRL2[FORCE] from this..,1: The master force signal from submodule 0 is used..,2: The local reload signal from this submodule is..,3: The master reload signal from submodule0 is used..,4: The local sync signal from this submodule is..,5: The master sync signal from submodule0 is used..,6: The external force signal EXT_FORCE from outside..,7: The external sync signal EXT_SYNC from outside.." newline bitfld.word 0x2 2. "RELOAD_SEL,Reload Source Select" "0: The local RELOAD signal is used to reload..,1: The master RELOAD signal (from submodule 0) is.." bitfld.word 0x2 0.--1. "CLK_SEL,Clock Source Select" "0: The IPBus clock is used as the clock for the..,1: EXT_CLK is used as the clock for the local..,2: Submodule 0's clock (AUX_CLK) is used as the..,?" line.word 0x4 "SMCTRL,Control Register" hexmask.word.byte 0x4 12.--15. 1. "LDFQ,Load Frequency" bitfld.word 0x4 11. "HALF,Half Cycle Reload" "0: Half-cycle reloads disabled.,1: Half-cycle reloads enabled." newline bitfld.word 0x4 10. "FULL,Full Cycle Reload" "0: Full-cycle reloads disabled.,1: Full-cycle reloads enabled." rbitfld.word 0x4 8.--9. "DT,Deadtime" "0,1,2,3" newline bitfld.word 0x4 7. "COMPMODE,Compare Mode" "0: The VAL* registers and the PWM counter are..,1: The VAL* registers and the PWM counter are.." bitfld.word 0x4 4.--6. "PRSC,Prescaler" "0: Prescaler 1,1: Prescaler 2,2: Prescaler 4,3: Prescaler 8,4: Prescaler 16,5: Prescaler 32,6: Prescaler 64,7: Prescaler 128" newline bitfld.word 0x4 3. "SPLIT,Split the DBLPWM signal to PWMA and PWMB" "0: DBLPWM is not split. PWMA and PWMB each have..,1: DBLPWM is split to PWMA and PWMB." bitfld.word 0x4 2. "LDMOD,Load Mode Select" "0: Buffered registers of this submodule are loaded..,1: Buffered registers of this submodule are loaded.." newline bitfld.word 0x4 1. "DBLX,PWMX Double Switching Enable" "0: PWMX double pulse disabled.,1: PWMX double pulse enabled." bitfld.word 0x4 0. "DBLEN,Double Switching Enable" "0: Double switching disabled.,1: Double switching enabled." group.word ($2+0xA)++0x23 line.word 0x0 "SMVAL0,Value Register 0" hexmask.word 0x0 0.--15. 1. "VAL0,Value Register 0" line.word 0x2 "SMFRACVAL1,Fractional Value Register 1" hexmask.word.byte 0x2 11.--15. 1. "FRACVAL1,Fractional Value 1 Register" line.word 0x4 "SMVAL1,Value Register 1" hexmask.word 0x4 0.--15. 1. "VAL1,Value Register 1" line.word 0x6 "SMFRACVAL2,Fractional Value Register 2" hexmask.word.byte 0x6 11.--15. 1. "FRACVAL2,Fractional Value 2" line.word 0x8 "SMVAL2,Value Register 2" hexmask.word 0x8 0.--15. 1. "VAL2,Value Register 2" line.word 0xA "SMFRACVAL3,Fractional Value Register 3" hexmask.word.byte 0xA 11.--15. 1. "FRACVAL3,Fractional Value 3" line.word 0xC "SMVAL3,Value Register 3" hexmask.word 0xC 0.--15. 1. "VAL3,Value Register 3" line.word 0xE "SMFRACVAL4,Fractional Value Register 4" hexmask.word.byte 0xE 11.--15. 1. "FRACVAL4,Fractional Value 4" line.word 0x10 "SMVAL4,Value Register 4" hexmask.word 0x10 0.--15. 1. "VAL4,Value Register 4" line.word 0x12 "SMFRACVAL5,Fractional Value Register 5" hexmask.word.byte 0x12 11.--15. 1. "FRACVAL5,Fractional Value 5" line.word 0x14 "SMVAL5,Value Register 5" hexmask.word 0x14 0.--15. 1. "VAL5,Value Register 5" line.word 0x16 "SMFRCTRL,Fractional Control Register" rbitfld.word 0x16 15. "TEST,Test Status Bit" "0,1" bitfld.word 0x16 4. "FRAC45_EN,Fractional Cycle Placement Enable for PWM_B" "0: Disable fractional cycle placement for PWM_B.,1: Enable fractional cycle placement for PWM_B." newline bitfld.word 0x16 2. "FRAC23_EN,Fractional Cycle Placement Enable for PWM_A" "0: Disable fractional cycle placement for PWM_A.,1: Enable fractional cycle placement for PWM_A." bitfld.word 0x16 1. "FRAC1_EN,Fractional Cycle PWM Period Enable" "0: Disable fractional cycle length for the PWM..,1: Enable fractional cycle length for the PWM period." line.word 0x18 "SMOCTRL,Output Control Register" rbitfld.word 0x18 15. "PWMA_IN,PWM_A Input" "0,1" rbitfld.word 0x18 14. "PWMB_IN,PWM_B Input" "0,1" newline rbitfld.word 0x18 13. "PWMX_IN,PWM_X Input" "0,1" bitfld.word 0x18 10. "POLA,PWM_A Output Polarity" "0: PWM_A output not inverted. A high level on the..,1: PWM_A output inverted. A low level on the PWM_A.." newline bitfld.word 0x18 9. "POLB,PWM_B Output Polarity" "0: PWM_B output not inverted. A high level on the..,1: PWM_B output inverted. A low level on the PWM_B.." bitfld.word 0x18 8. "POLX,PWM_X Output Polarity" "0: PWM_X output not inverted. A high level on the..,1: PWM_X output inverted. A low level on the PWM_X.." newline bitfld.word 0x18 4.--5. "PWMAFS,PWM_A Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." bitfld.word 0x18 2.--3. "PWMBFS,PWM_B Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." newline bitfld.word 0x18 0.--1. "PWMXFS,PWM_X Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." line.word 0x1A "SMSTS,Status Register" rbitfld.word 0x1A 14. "RUF,Registers Updated Flag" "0: No register update has occurred since last reload.,1: At least one of the double buffered registers.." eventfld.word 0x1A 13. "REF,Reload Error Flag" "0: No reload error occurred.,1: Reload signal occurred with non-coherent data.." newline eventfld.word 0x1A 12. "RF,Reload Flag" "0: No new reload cycle since last STS[RF] clearing,1: New reload cycle since last STS[RF] clearing" eventfld.word 0x1A 11. "CFA1,Capture Flag A1" "0,1" newline eventfld.word 0x1A 10. "CFA0,Capture Flag A0" "0,1" eventfld.word 0x1A 9. "CFB1,Capture Flag B1" "0,1" newline eventfld.word 0x1A 8. "CFB0,Capture Flag B0" "0,1" eventfld.word 0x1A 7. "CFX1,Capture Flag X1" "0,1" newline eventfld.word 0x1A 6. "CFX0,Capture Flag X0" "0,1" hexmask.word.byte 0x1A 0.--5. 1. "CMPF,Compare Flags" line.word 0x1C "SMINTEN,Interrupt Enable Register" bitfld.word 0x1C 13. "REIE,Reload Error Interrupt Enable" "0: STS[REF] CPU interrupt requests disabled,1: STS[REF] CPU interrupt requests enabled" bitfld.word 0x1C 12. "RIE,Reload Interrupt Enable" "0: STS[RF] CPU interrupt requests disabled,1: STS[RF] CPU interrupt requests enabled" newline bitfld.word 0x1C 11. "CA1IE,Capture A 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFA1].,1: Interrupt request enabled for STS[CFA1]." bitfld.word 0x1C 10. "CA0IE,Capture A 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFA0].,1: Interrupt request enabled for STS[CFA0]." newline bitfld.word 0x1C 9. "CB1IE,Capture B 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFB1].,1: Interrupt request enabled for STS[CFB1]." bitfld.word 0x1C 8. "CB0IE,Capture B 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFB0].,1: Interrupt request enabled for STS[CFB0]." newline bitfld.word 0x1C 7. "CX1IE,Capture X 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFX1].,1: Interrupt request enabled for STS[CFX1]." bitfld.word 0x1C 6. "CX0IE,Capture X 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFX0].,1: Interrupt request enabled for STS[CFX0]." newline hexmask.word.byte 0x1C 0.--5. 1. "CMPIE,Compare Interrupt Enables" line.word 0x1E "SMDMAEN,DMA Enable Register" bitfld.word 0x1E 9. "VALDE,Value Registers DMA Enable" "0: DMA write requests disabled,1: Enabled" bitfld.word 0x1E 8. "FAND,FIFO Watermark AND Control" "0: Selected FIFO watermarks are OR'ed together.,1: Selected FIFO watermarks are AND'ed together." newline bitfld.word 0x1E 6.--7. "CAPTDE,Capture DMA Enable Source Select" "0: Read DMA requests disabled.,1: Exceeding a FIFO watermark sets the DMA read..,2: A local sync (VAL1 matches counter) sets the..,3: A local reload (STS[RF] being set) sets the read.." bitfld.word 0x1E 5. "CA1DE,Capture A1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 4. "CA0DE,Capture A0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 3. "CB1DE,Capture B1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 2. "CB0DE,Capture B0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 1. "CX1DE,Capture X1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 0. "CX0DE,Capture X0 FIFO DMA Enable" "0,1" line.word 0x20 "SMTCTRL,Output Trigger Control Register" bitfld.word 0x20 15. "PWAOT0,Output Trigger 0 Source Select" "0: Route the PWM_OUT_TRIG0 signal to PWM_OUT_TRIG0..,1: Route the PWMA output to the PWM_OUT_TRIG0 port." bitfld.word 0x20 14. "PWBOT1,Output Trigger 1 Source Select" "0: Route the PWM_OUT_TRIG1 signal to PWM_OUT_TRIG1..,1: Route the PWMB output to the PWM_OUT_TRIG1 port." newline bitfld.word 0x20 12. "TRGFRQ,Trigger frequency" "0: Trigger outputs are generated during every PWM..,1: Trigger outputs are generated only during the.." hexmask.word.byte 0x20 0.--5. 1. "OUT_TRIG_EN,Output Trigger Enables" line.word 0x22 "SMDISMAP0,Fault Disable Mapping Register 0" hexmask.word.byte 0x22 8.--11. 1. "DIS0X,PWM_X Fault Disable Mask 0" hexmask.word.byte 0x22 4.--7. 1. "DIS0B,PWM_B Fault Disable Mask 0" newline hexmask.word.byte 0x22 0.--3. 1. "DIS0A,PWM_A Fault Disable Mask 0" group.word ($2+0x30)++0xF line.word 0x0 "SMDTCNT0,Deadtime Count Register 0" hexmask.word 0x0 0.--15. 1. "DTCNT0,DTCNT0" line.word 0x2 "SMDTCNT1,Deadtime Count Register 1" hexmask.word 0x2 0.--15. 1. "DTCNT1,DTCNT1" line.word 0x4 "SMCAPTCTRLA,Capture Control A Register" rbitfld.word 0x4 13.--15. "CA1CNT,Capture A1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x4 10.--12. "CA0CNT,Capture A0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x4 8.--9. "CFAWM,Capture A FIFOs Water Mark" "0,1,2,3" bitfld.word 0x4 7. "EDGCNTA_EN,Edge Counter A Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x4 6. "INP_SELA,Input Select A" "0: Raw PWM_A input signal selected as source.,1: Edge Counter" bitfld.word 0x4 4.--5. "EDGA1,Edge A 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x4 2.--3. "EDGA0,Edge A 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x4 1. "ONESHOTA,One Shot Mode A" "0: Free Running,1: One Shot" newline bitfld.word 0x4 0. "ARMA,Arm A" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0x6 "SMCAPTCOMPA,Capture Compare A Register" hexmask.word.byte 0x6 8.--15. 1. "EDGCNTA,Edge Counter A" hexmask.word.byte 0x6 0.--7. 1. "EDGCMPA,Edge Compare A" line.word 0x8 "SMCAPTCTRLB,Capture Control B Register" rbitfld.word 0x8 13.--15. "CB1CNT,Capture B1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x8 10.--12. "CB0CNT,Capture B0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x8 8.--9. "CFBWM,Capture B FIFOs Water Mark" "0,1,2,3" bitfld.word 0x8 7. "EDGCNTB_EN,Edge Counter B Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x8 6. "INP_SELB,Input Select B" "0: Raw PWM_B input signal selected as source.,1: Edge Counter" bitfld.word 0x8 4.--5. "EDGB1,Edge B 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x8 2.--3. "EDGB0,Edge B 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x8 1. "ONESHOTB,One Shot Mode B" "0: Free Running,1: One Shot" newline bitfld.word 0x8 0. "ARMB,Arm B" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xA "SMCAPTCOMPB,Capture Compare B Register" hexmask.word.byte 0xA 8.--15. 1. "EDGCNTB,Edge Counter B" hexmask.word.byte 0xA 0.--7. 1. "EDGCMPB,Edge Compare B" line.word 0xC "SMCAPTCTRLX,Capture Control X Register" rbitfld.word 0xC 13.--15. "CX1CNT,Capture X1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0xC 10.--12. "CX0CNT,Capture X0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0xC 8.--9. "CFXWM,Capture X FIFOs Water Mark" "0,1,2,3" bitfld.word 0xC 7. "EDGCNTX_EN,Edge Counter X Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0xC 6. "INP_SELX,Input Select X" "0: Raw PWM_X input signal selected as source.,1: Edge Counter" bitfld.word 0xC 4.--5. "EDGX1,Edge X 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0xC 2.--3. "EDGX0,Edge X 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0xC 1. "ONESHOTX,One Shot Mode Aux" "0: Free Running,1: One Shot" newline bitfld.word 0xC 0. "ARMX,Arm X" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xE "SMCAPTCOMPX,Capture Compare X Register" hexmask.word.byte 0xE 8.--15. 1. "EDGCNTX,Edge Counter X" hexmask.word.byte 0xE 0.--7. 1. "EDGCMPX,Edge Compare X" rgroup.word ($2+0x40)++0x17 line.word 0x0 "SMCVAL0,Capture Value 0 Register" hexmask.word 0x0 0.--15. 1. "CAPTVAL0,CAPTVAL0" line.word 0x2 "SMCVAL0CYC,Capture Value 0 Cycle Register" hexmask.word.byte 0x2 0.--3. 1. "CVAL0CYC,CVAL0CYC" line.word 0x4 "SMCVAL1,Capture Value 1 Register" hexmask.word 0x4 0.--15. 1. "CAPTVAL1,CAPTVAL1" line.word 0x6 "SMCVAL1CYC,Capture Value 1 Cycle Register" hexmask.word.byte 0x6 0.--3. 1. "CVAL1CYC,CVAL1CYC" line.word 0x8 "SMCVAL2,Capture Value 2 Register" hexmask.word 0x8 0.--15. 1. "CAPTVAL2,CAPTVAL2" line.word 0xA "SMCVAL2CYC,Capture Value 2 Cycle Register" hexmask.word.byte 0xA 0.--3. 1. "CVAL2CYC,CVAL2CYC" line.word 0xC "SMCVAL3,Capture Value 3 Register" hexmask.word 0xC 0.--15. 1. "CAPTVAL3,CAPTVAL3" line.word 0xE "SMCVAL3CYC,Capture Value 3 Cycle Register" hexmask.word.byte 0xE 0.--3. 1. "CVAL3CYC,CVAL3CYC" line.word 0x10 "SMCVAL4,Capture Value 4 Register" hexmask.word 0x10 0.--15. 1. "CAPTVAL4,CAPTVAL4" line.word 0x12 "SMCVAL4CYC,Capture Value 4 Cycle Register" hexmask.word.byte 0x12 0.--3. 1. "CVAL4CYC,CVAL4CYC" line.word 0x14 "SMCVAL5,Capture Value 5 Register" hexmask.word 0x14 0.--15. 1. "CAPTVAL5,CAPTVAL5" line.word 0x16 "SMCVAL5CYC,Capture Value 5 Cycle Register" hexmask.word.byte 0x16 0.--3. 1. "CVAL5CYC,CVAL5CYC" tree.end repeat.end base ad:0x40190000 group.word 0x180++0x15 line.word 0x0 "OUTEN,Output Enable Register" hexmask.word.byte 0x0 8.--11. 1. "PWMA_EN,PWM_A Output Enables" hexmask.word.byte 0x0 4.--7. 1. "PWMB_EN,PWM_B Output Enables" newline hexmask.word.byte 0x0 0.--3. 1. "PWMX_EN,PWM_X Output Enables" line.word 0x2 "MASK,Mask Register" hexmask.word.byte 0x2 8.--11. 1. "MASKA,PWM_A Masks" hexmask.word.byte 0x2 4.--7. 1. "MASKB,PWM_B Masks" newline hexmask.word.byte 0x2 0.--3. 1. "MASKX,PWM_X Masks" line.word 0x4 "SWCOUT,Software Controlled Output Register" bitfld.word 0x4 7. "SM3OUT23,Submodule 3 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 6. "SM3OUT45,Submodule 3 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 5. "SM2OUT23,Submodule 2 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 4. "SM2OUT45,Submodule 2 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 3. "SM1OUT23,Submodule 1 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 2. "SM1OUT45,Submodule 1 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 1. "SM0OUT23,Submodule 0 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 0. "SM0OUT45,Submodule 0 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." line.word 0x6 "DTSRCSEL,PWM Source Select Register" bitfld.word 0x6 14.--15. "SM3SEL23,Submodule 3 PWM23 Control Select" "0: Generated SM3PWM23 signal is used by the..,1: Inverted generated SM3PWM23 signal is used by..,2: SWCOUT[SM3OUT23] is used by the deadtime logic.,3: PWM3_EXTA signal is used by the deadtime logic." bitfld.word 0x6 12.--13. "SM3SEL45,Submodule 3 PWM45 Control Select" "0: Generated SM3PWM45 signal is used by the..,1: Inverted generated SM3PWM45 signal is used by..,2: SWCOUT[SM3OUT45] is used by the deadtime logic.,3: PWM3_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 10.--11. "SM2SEL23,Submodule 2 PWM23 Control Select" "0: Generated SM2PWM23 signal is used by the..,1: Inverted generated SM2PWM23 signal is used by..,2: SWCOUT[SM2OUT23] is used by the deadtime logic.,3: PWM2_EXTA signal is used by the deadtime logic." bitfld.word 0x6 8.--9. "SM2SEL45,Submodule 2 PWM45 Control Select" "0: Generated SM2PWM45 signal is used by the..,1: Inverted generated SM2PWM45 signal is used by..,2: SWCOUT[SM2OUT45] is used by the deadtime logic.,3: PWM2_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 6.--7. "SM1SEL23,Submodule 1 PWM23 Control Select" "0: Generated SM1PWM23 signal is used by the..,1: Inverted generated SM1PWM23 signal is used by..,2: SWCOUT[SM1OUT23] is used by the deadtime logic.,3: PWM1_EXTA signal is used by the deadtime logic." bitfld.word 0x6 4.--5. "SM1SEL45,Submodule 1 PWM45 Control Select" "0: Generated SM1PWM45 signal is used by the..,1: Inverted generated SM1PWM45 signal is used by..,2: SWCOUT[SM1OUT45] is used by the deadtime logic.,3: PWM1_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 2.--3. "SM0SEL23,Submodule 0 PWM23 Control Select" "0: Generated SM0PWM23 signal is used by the..,1: Inverted generated SM0PWM23 signal is used by..,2: SWCOUT[SM0OUT23] is used by the deadtime logic.,3: PWM0_EXTA signal is used by the deadtime logic." bitfld.word 0x6 0.--1. "SM0SEL45,Submodule 0 PWM45 Control Select" "0: Generated SM0PWM45 signal is used by the..,1: Inverted generated SM0PWM45 signal is used by..,2: SWCOUT[SM0OUT45] is used by the deadtime logic.,3: PWM0_EXTB signal is used by the deadtime logic." line.word 0x8 "MCTRL,Master Control Register" hexmask.word.byte 0x8 12.--15. 1. "IPOL,Current Polarity" hexmask.word.byte 0x8 8.--11. 1. "RUN,Run" newline hexmask.word.byte 0x8 4.--7. 1. "CLDOK,Clear Load Okay" hexmask.word.byte 0x8 0.--3. 1. "LDOK,Load Okay" line.word 0xA "MCTRL2,Master Control 2 Register" bitfld.word 0xA 0.--1. "MONPLL,Monitor PLL State" "0: Not locked. Do not monitor PLL operation.,1: Not locked. Monitor PLL operation to..,2: Locked. Do not monitor PLL operation. Resetting..,3: Locked. Monitor PLL operation to automatically.." line.word 0xC "FCTRL0,Fault Control Register" hexmask.word.byte 0xC 12.--15. 1. "FLVL,Fault Level" hexmask.word.byte 0xC 8.--11. 1. "FAUTO,Automatic Fault Clearing" newline hexmask.word.byte 0xC 4.--7. 1. "FSAFE,Fault Safety Mode" hexmask.word.byte 0xC 0.--3. 1. "FIE,Fault Interrupt Enables" line.word 0xE "FSTS0,Fault Status Register" hexmask.word.byte 0xE 12.--15. 1. "FHALF,Half Cycle Fault Recovery" hexmask.word.byte 0xE 8.--11. 1. "FFPIN,Filtered Fault Pins" newline hexmask.word.byte 0xE 4.--7. 1. "FFULL,Full Cycle" hexmask.word.byte 0xE 0.--3. 1. "FFLAG,Fault Flags" line.word 0x10 "FFILT0,Fault Filter Register" bitfld.word 0x10 15. "GSTR,Fault Glitch Stretch Enable" "0: Fault input glitch stretching is disabled.,1: Input fault signals will be stretched to at.." bitfld.word 0x10 8.--10. "FILT_CNT,Fault Filter Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x10 0.--7. 1. "FILT_PER,Fault Filter Period" line.word 0x12 "FTST0,Fault Test Register" bitfld.word 0x12 0. "FTEST,Fault Test" "0: No fault,1: Cause a simulated fault" line.word 0x14 "FCTRL20,Fault Control 2 Register" hexmask.word.byte 0x14 0.--3. 1. "NOCOMB,No Combinational Path From Fault Input To PWM Output" tree.end tree "PWM3" base ad:0x40194000 repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40194000 ad:0x40194060 ad:0x401940C0 ad:0x40194120) tree "SM[$1]" base $2 rgroup.word ($2)++0x1 line.word 0x0 "SMCNT,Counter Register" hexmask.word 0x0 0.--15. 1. "CNT,Counter Register Bits" group.word ($2+0x2)++0x5 line.word 0x0 "SMINIT,Initial Count Register" hexmask.word 0x0 0.--15. 1. "INIT,Initial Count Register Bits" line.word 0x2 "SMCTRL2,Control 2 Register" bitfld.word 0x2 15. "DBGEN,Debug Enable" "0,1" bitfld.word 0x2 14. "WAITEN,WAIT Enable" "0,1" newline bitfld.word 0x2 13. "INDEP,Independent or Complementary Pair Operation" "0: PWM_A and PWM_B form a complementary PWM pair.,1: PWM_A and PWM_B outputs are independent PWMs." bitfld.word 0x2 12. "PWM23_INIT,PWM23 Initial Value" "0,1" newline bitfld.word 0x2 11. "PWM45_INIT,PWM45 Initial Value" "0,1" bitfld.word 0x2 10. "PWMX_INIT,PWM_X Initial Value" "0,1" newline bitfld.word 0x2 8.--9. "INIT_SEL,Initialization Control Select" "0: Local sync (PWM_X) causes initialization.,1: Master reload from submodule 0 causes..,2: Master sync from submodule 0 causes..,3: EXT_SYNC causes initialization." bitfld.word 0x2 7. "FRCEN,FRCEN" "0: Initialization from a FORCE_OUT is disabled.,1: Initialization from a FORCE_OUT is enabled." newline bitfld.word 0x2 6. "FORCE,Force Initialization" "0,1" bitfld.word 0x2 3.--5. "FORCE_SEL,This read/write bit determines the source of the FORCE OUTPUT signal for this submodule." "0: The local force signal CTRL2[FORCE] from this..,1: The master force signal from submodule 0 is used..,2: The local reload signal from this submodule is..,3: The master reload signal from submodule0 is used..,4: The local sync signal from this submodule is..,5: The master sync signal from submodule0 is used..,6: The external force signal EXT_FORCE from outside..,7: The external sync signal EXT_SYNC from outside.." newline bitfld.word 0x2 2. "RELOAD_SEL,Reload Source Select" "0: The local RELOAD signal is used to reload..,1: The master RELOAD signal (from submodule 0) is.." bitfld.word 0x2 0.--1. "CLK_SEL,Clock Source Select" "0: The IPBus clock is used as the clock for the..,1: EXT_CLK is used as the clock for the local..,2: Submodule 0's clock (AUX_CLK) is used as the..,?" line.word 0x4 "SMCTRL,Control Register" hexmask.word.byte 0x4 12.--15. 1. "LDFQ,Load Frequency" bitfld.word 0x4 11. "HALF,Half Cycle Reload" "0: Half-cycle reloads disabled.,1: Half-cycle reloads enabled." newline bitfld.word 0x4 10. "FULL,Full Cycle Reload" "0: Full-cycle reloads disabled.,1: Full-cycle reloads enabled." rbitfld.word 0x4 8.--9. "DT,Deadtime" "0,1,2,3" newline bitfld.word 0x4 7. "COMPMODE,Compare Mode" "0: The VAL* registers and the PWM counter are..,1: The VAL* registers and the PWM counter are.." bitfld.word 0x4 4.--6. "PRSC,Prescaler" "0: Prescaler 1,1: Prescaler 2,2: Prescaler 4,3: Prescaler 8,4: Prescaler 16,5: Prescaler 32,6: Prescaler 64,7: Prescaler 128" newline bitfld.word 0x4 3. "SPLIT,Split the DBLPWM signal to PWMA and PWMB" "0: DBLPWM is not split. PWMA and PWMB each have..,1: DBLPWM is split to PWMA and PWMB." bitfld.word 0x4 2. "LDMOD,Load Mode Select" "0: Buffered registers of this submodule are loaded..,1: Buffered registers of this submodule are loaded.." newline bitfld.word 0x4 1. "DBLX,PWMX Double Switching Enable" "0: PWMX double pulse disabled.,1: PWMX double pulse enabled." bitfld.word 0x4 0. "DBLEN,Double Switching Enable" "0: Double switching disabled.,1: Double switching enabled." group.word ($2+0xA)++0x23 line.word 0x0 "SMVAL0,Value Register 0" hexmask.word 0x0 0.--15. 1. "VAL0,Value Register 0" line.word 0x2 "SMFRACVAL1,Fractional Value Register 1" hexmask.word.byte 0x2 11.--15. 1. "FRACVAL1,Fractional Value 1 Register" line.word 0x4 "SMVAL1,Value Register 1" hexmask.word 0x4 0.--15. 1. "VAL1,Value Register 1" line.word 0x6 "SMFRACVAL2,Fractional Value Register 2" hexmask.word.byte 0x6 11.--15. 1. "FRACVAL2,Fractional Value 2" line.word 0x8 "SMVAL2,Value Register 2" hexmask.word 0x8 0.--15. 1. "VAL2,Value Register 2" line.word 0xA "SMFRACVAL3,Fractional Value Register 3" hexmask.word.byte 0xA 11.--15. 1. "FRACVAL3,Fractional Value 3" line.word 0xC "SMVAL3,Value Register 3" hexmask.word 0xC 0.--15. 1. "VAL3,Value Register 3" line.word 0xE "SMFRACVAL4,Fractional Value Register 4" hexmask.word.byte 0xE 11.--15. 1. "FRACVAL4,Fractional Value 4" line.word 0x10 "SMVAL4,Value Register 4" hexmask.word 0x10 0.--15. 1. "VAL4,Value Register 4" line.word 0x12 "SMFRACVAL5,Fractional Value Register 5" hexmask.word.byte 0x12 11.--15. 1. "FRACVAL5,Fractional Value 5" line.word 0x14 "SMVAL5,Value Register 5" hexmask.word 0x14 0.--15. 1. "VAL5,Value Register 5" line.word 0x16 "SMFRCTRL,Fractional Control Register" rbitfld.word 0x16 15. "TEST,Test Status Bit" "0,1" bitfld.word 0x16 4. "FRAC45_EN,Fractional Cycle Placement Enable for PWM_B" "0: Disable fractional cycle placement for PWM_B.,1: Enable fractional cycle placement for PWM_B." newline bitfld.word 0x16 2. "FRAC23_EN,Fractional Cycle Placement Enable for PWM_A" "0: Disable fractional cycle placement for PWM_A.,1: Enable fractional cycle placement for PWM_A." bitfld.word 0x16 1. "FRAC1_EN,Fractional Cycle PWM Period Enable" "0: Disable fractional cycle length for the PWM..,1: Enable fractional cycle length for the PWM period." line.word 0x18 "SMOCTRL,Output Control Register" rbitfld.word 0x18 15. "PWMA_IN,PWM_A Input" "0,1" rbitfld.word 0x18 14. "PWMB_IN,PWM_B Input" "0,1" newline rbitfld.word 0x18 13. "PWMX_IN,PWM_X Input" "0,1" bitfld.word 0x18 10. "POLA,PWM_A Output Polarity" "0: PWM_A output not inverted. A high level on the..,1: PWM_A output inverted. A low level on the PWM_A.." newline bitfld.word 0x18 9. "POLB,PWM_B Output Polarity" "0: PWM_B output not inverted. A high level on the..,1: PWM_B output inverted. A low level on the PWM_B.." bitfld.word 0x18 8. "POLX,PWM_X Output Polarity" "0: PWM_X output not inverted. A high level on the..,1: PWM_X output inverted. A low level on the PWM_X.." newline bitfld.word 0x18 4.--5. "PWMAFS,PWM_A Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." bitfld.word 0x18 2.--3. "PWMBFS,PWM_B Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." newline bitfld.word 0x18 0.--1. "PWMXFS,PWM_X Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." line.word 0x1A "SMSTS,Status Register" rbitfld.word 0x1A 14. "RUF,Registers Updated Flag" "0: No register update has occurred since last reload.,1: At least one of the double buffered registers.." eventfld.word 0x1A 13. "REF,Reload Error Flag" "0: No reload error occurred.,1: Reload signal occurred with non-coherent data.." newline eventfld.word 0x1A 12. "RF,Reload Flag" "0: No new reload cycle since last STS[RF] clearing,1: New reload cycle since last STS[RF] clearing" eventfld.word 0x1A 11. "CFA1,Capture Flag A1" "0,1" newline eventfld.word 0x1A 10. "CFA0,Capture Flag A0" "0,1" eventfld.word 0x1A 9. "CFB1,Capture Flag B1" "0,1" newline eventfld.word 0x1A 8. "CFB0,Capture Flag B0" "0,1" eventfld.word 0x1A 7. "CFX1,Capture Flag X1" "0,1" newline eventfld.word 0x1A 6. "CFX0,Capture Flag X0" "0,1" hexmask.word.byte 0x1A 0.--5. 1. "CMPF,Compare Flags" line.word 0x1C "SMINTEN,Interrupt Enable Register" bitfld.word 0x1C 13. "REIE,Reload Error Interrupt Enable" "0: STS[REF] CPU interrupt requests disabled,1: STS[REF] CPU interrupt requests enabled" bitfld.word 0x1C 12. "RIE,Reload Interrupt Enable" "0: STS[RF] CPU interrupt requests disabled,1: STS[RF] CPU interrupt requests enabled" newline bitfld.word 0x1C 11. "CA1IE,Capture A 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFA1].,1: Interrupt request enabled for STS[CFA1]." bitfld.word 0x1C 10. "CA0IE,Capture A 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFA0].,1: Interrupt request enabled for STS[CFA0]." newline bitfld.word 0x1C 9. "CB1IE,Capture B 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFB1].,1: Interrupt request enabled for STS[CFB1]." bitfld.word 0x1C 8. "CB0IE,Capture B 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFB0].,1: Interrupt request enabled for STS[CFB0]." newline bitfld.word 0x1C 7. "CX1IE,Capture X 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFX1].,1: Interrupt request enabled for STS[CFX1]." bitfld.word 0x1C 6. "CX0IE,Capture X 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFX0].,1: Interrupt request enabled for STS[CFX0]." newline hexmask.word.byte 0x1C 0.--5. 1. "CMPIE,Compare Interrupt Enables" line.word 0x1E "SMDMAEN,DMA Enable Register" bitfld.word 0x1E 9. "VALDE,Value Registers DMA Enable" "0: DMA write requests disabled,1: Enabled" bitfld.word 0x1E 8. "FAND,FIFO Watermark AND Control" "0: Selected FIFO watermarks are OR'ed together.,1: Selected FIFO watermarks are AND'ed together." newline bitfld.word 0x1E 6.--7. "CAPTDE,Capture DMA Enable Source Select" "0: Read DMA requests disabled.,1: Exceeding a FIFO watermark sets the DMA read..,2: A local sync (VAL1 matches counter) sets the..,3: A local reload (STS[RF] being set) sets the read.." bitfld.word 0x1E 5. "CA1DE,Capture A1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 4. "CA0DE,Capture A0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 3. "CB1DE,Capture B1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 2. "CB0DE,Capture B0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 1. "CX1DE,Capture X1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 0. "CX0DE,Capture X0 FIFO DMA Enable" "0,1" line.word 0x20 "SMTCTRL,Output Trigger Control Register" bitfld.word 0x20 15. "PWAOT0,Output Trigger 0 Source Select" "0: Route the PWM_OUT_TRIG0 signal to PWM_OUT_TRIG0..,1: Route the PWMA output to the PWM_OUT_TRIG0 port." bitfld.word 0x20 14. "PWBOT1,Output Trigger 1 Source Select" "0: Route the PWM_OUT_TRIG1 signal to PWM_OUT_TRIG1..,1: Route the PWMB output to the PWM_OUT_TRIG1 port." newline bitfld.word 0x20 12. "TRGFRQ,Trigger frequency" "0: Trigger outputs are generated during every PWM..,1: Trigger outputs are generated only during the.." hexmask.word.byte 0x20 0.--5. 1. "OUT_TRIG_EN,Output Trigger Enables" line.word 0x22 "SMDISMAP0,Fault Disable Mapping Register 0" hexmask.word.byte 0x22 8.--11. 1. "DIS0X,PWM_X Fault Disable Mask 0" hexmask.word.byte 0x22 4.--7. 1. "DIS0B,PWM_B Fault Disable Mask 0" newline hexmask.word.byte 0x22 0.--3. 1. "DIS0A,PWM_A Fault Disable Mask 0" group.word ($2+0x30)++0xF line.word 0x0 "SMDTCNT0,Deadtime Count Register 0" hexmask.word 0x0 0.--15. 1. "DTCNT0,DTCNT0" line.word 0x2 "SMDTCNT1,Deadtime Count Register 1" hexmask.word 0x2 0.--15. 1. "DTCNT1,DTCNT1" line.word 0x4 "SMCAPTCTRLA,Capture Control A Register" rbitfld.word 0x4 13.--15. "CA1CNT,Capture A1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x4 10.--12. "CA0CNT,Capture A0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x4 8.--9. "CFAWM,Capture A FIFOs Water Mark" "0,1,2,3" bitfld.word 0x4 7. "EDGCNTA_EN,Edge Counter A Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x4 6. "INP_SELA,Input Select A" "0: Raw PWM_A input signal selected as source.,1: Edge Counter" bitfld.word 0x4 4.--5. "EDGA1,Edge A 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x4 2.--3. "EDGA0,Edge A 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x4 1. "ONESHOTA,One Shot Mode A" "0: Free Running,1: One Shot" newline bitfld.word 0x4 0. "ARMA,Arm A" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0x6 "SMCAPTCOMPA,Capture Compare A Register" hexmask.word.byte 0x6 8.--15. 1. "EDGCNTA,Edge Counter A" hexmask.word.byte 0x6 0.--7. 1. "EDGCMPA,Edge Compare A" line.word 0x8 "SMCAPTCTRLB,Capture Control B Register" rbitfld.word 0x8 13.--15. "CB1CNT,Capture B1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x8 10.--12. "CB0CNT,Capture B0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x8 8.--9. "CFBWM,Capture B FIFOs Water Mark" "0,1,2,3" bitfld.word 0x8 7. "EDGCNTB_EN,Edge Counter B Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x8 6. "INP_SELB,Input Select B" "0: Raw PWM_B input signal selected as source.,1: Edge Counter" bitfld.word 0x8 4.--5. "EDGB1,Edge B 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x8 2.--3. "EDGB0,Edge B 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x8 1. "ONESHOTB,One Shot Mode B" "0: Free Running,1: One Shot" newline bitfld.word 0x8 0. "ARMB,Arm B" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xA "SMCAPTCOMPB,Capture Compare B Register" hexmask.word.byte 0xA 8.--15. 1. "EDGCNTB,Edge Counter B" hexmask.word.byte 0xA 0.--7. 1. "EDGCMPB,Edge Compare B" line.word 0xC "SMCAPTCTRLX,Capture Control X Register" rbitfld.word 0xC 13.--15. "CX1CNT,Capture X1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0xC 10.--12. "CX0CNT,Capture X0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0xC 8.--9. "CFXWM,Capture X FIFOs Water Mark" "0,1,2,3" bitfld.word 0xC 7. "EDGCNTX_EN,Edge Counter X Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0xC 6. "INP_SELX,Input Select X" "0: Raw PWM_X input signal selected as source.,1: Edge Counter" bitfld.word 0xC 4.--5. "EDGX1,Edge X 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0xC 2.--3. "EDGX0,Edge X 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0xC 1. "ONESHOTX,One Shot Mode Aux" "0: Free Running,1: One Shot" newline bitfld.word 0xC 0. "ARMX,Arm X" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xE "SMCAPTCOMPX,Capture Compare X Register" hexmask.word.byte 0xE 8.--15. 1. "EDGCNTX,Edge Counter X" hexmask.word.byte 0xE 0.--7. 1. "EDGCMPX,Edge Compare X" rgroup.word ($2+0x40)++0x17 line.word 0x0 "SMCVAL0,Capture Value 0 Register" hexmask.word 0x0 0.--15. 1. "CAPTVAL0,CAPTVAL0" line.word 0x2 "SMCVAL0CYC,Capture Value 0 Cycle Register" hexmask.word.byte 0x2 0.--3. 1. "CVAL0CYC,CVAL0CYC" line.word 0x4 "SMCVAL1,Capture Value 1 Register" hexmask.word 0x4 0.--15. 1. "CAPTVAL1,CAPTVAL1" line.word 0x6 "SMCVAL1CYC,Capture Value 1 Cycle Register" hexmask.word.byte 0x6 0.--3. 1. "CVAL1CYC,CVAL1CYC" line.word 0x8 "SMCVAL2,Capture Value 2 Register" hexmask.word 0x8 0.--15. 1. "CAPTVAL2,CAPTVAL2" line.word 0xA "SMCVAL2CYC,Capture Value 2 Cycle Register" hexmask.word.byte 0xA 0.--3. 1. "CVAL2CYC,CVAL2CYC" line.word 0xC "SMCVAL3,Capture Value 3 Register" hexmask.word 0xC 0.--15. 1. "CAPTVAL3,CAPTVAL3" line.word 0xE "SMCVAL3CYC,Capture Value 3 Cycle Register" hexmask.word.byte 0xE 0.--3. 1. "CVAL3CYC,CVAL3CYC" line.word 0x10 "SMCVAL4,Capture Value 4 Register" hexmask.word 0x10 0.--15. 1. "CAPTVAL4,CAPTVAL4" line.word 0x12 "SMCVAL4CYC,Capture Value 4 Cycle Register" hexmask.word.byte 0x12 0.--3. 1. "CVAL4CYC,CVAL4CYC" line.word 0x14 "SMCVAL5,Capture Value 5 Register" hexmask.word 0x14 0.--15. 1. "CAPTVAL5,CAPTVAL5" line.word 0x16 "SMCVAL5CYC,Capture Value 5 Cycle Register" hexmask.word.byte 0x16 0.--3. 1. "CVAL5CYC,CVAL5CYC" tree.end repeat.end base ad:0x40194000 group.word 0x180++0x15 line.word 0x0 "OUTEN,Output Enable Register" hexmask.word.byte 0x0 8.--11. 1. "PWMA_EN,PWM_A Output Enables" hexmask.word.byte 0x0 4.--7. 1. "PWMB_EN,PWM_B Output Enables" newline hexmask.word.byte 0x0 0.--3. 1. "PWMX_EN,PWM_X Output Enables" line.word 0x2 "MASK,Mask Register" hexmask.word.byte 0x2 8.--11. 1. "MASKA,PWM_A Masks" hexmask.word.byte 0x2 4.--7. 1. "MASKB,PWM_B Masks" newline hexmask.word.byte 0x2 0.--3. 1. "MASKX,PWM_X Masks" line.word 0x4 "SWCOUT,Software Controlled Output Register" bitfld.word 0x4 7. "SM3OUT23,Submodule 3 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 6. "SM3OUT45,Submodule 3 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 5. "SM2OUT23,Submodule 2 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 4. "SM2OUT45,Submodule 2 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 3. "SM1OUT23,Submodule 1 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 2. "SM1OUT45,Submodule 1 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 1. "SM0OUT23,Submodule 0 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 0. "SM0OUT45,Submodule 0 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." line.word 0x6 "DTSRCSEL,PWM Source Select Register" bitfld.word 0x6 14.--15. "SM3SEL23,Submodule 3 PWM23 Control Select" "0: Generated SM3PWM23 signal is used by the..,1: Inverted generated SM3PWM23 signal is used by..,2: SWCOUT[SM3OUT23] is used by the deadtime logic.,3: PWM3_EXTA signal is used by the deadtime logic." bitfld.word 0x6 12.--13. "SM3SEL45,Submodule 3 PWM45 Control Select" "0: Generated SM3PWM45 signal is used by the..,1: Inverted generated SM3PWM45 signal is used by..,2: SWCOUT[SM3OUT45] is used by the deadtime logic.,3: PWM3_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 10.--11. "SM2SEL23,Submodule 2 PWM23 Control Select" "0: Generated SM2PWM23 signal is used by the..,1: Inverted generated SM2PWM23 signal is used by..,2: SWCOUT[SM2OUT23] is used by the deadtime logic.,3: PWM2_EXTA signal is used by the deadtime logic." bitfld.word 0x6 8.--9. "SM2SEL45,Submodule 2 PWM45 Control Select" "0: Generated SM2PWM45 signal is used by the..,1: Inverted generated SM2PWM45 signal is used by..,2: SWCOUT[SM2OUT45] is used by the deadtime logic.,3: PWM2_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 6.--7. "SM1SEL23,Submodule 1 PWM23 Control Select" "0: Generated SM1PWM23 signal is used by the..,1: Inverted generated SM1PWM23 signal is used by..,2: SWCOUT[SM1OUT23] is used by the deadtime logic.,3: PWM1_EXTA signal is used by the deadtime logic." bitfld.word 0x6 4.--5. "SM1SEL45,Submodule 1 PWM45 Control Select" "0: Generated SM1PWM45 signal is used by the..,1: Inverted generated SM1PWM45 signal is used by..,2: SWCOUT[SM1OUT45] is used by the deadtime logic.,3: PWM1_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 2.--3. "SM0SEL23,Submodule 0 PWM23 Control Select" "0: Generated SM0PWM23 signal is used by the..,1: Inverted generated SM0PWM23 signal is used by..,2: SWCOUT[SM0OUT23] is used by the deadtime logic.,3: PWM0_EXTA signal is used by the deadtime logic." bitfld.word 0x6 0.--1. "SM0SEL45,Submodule 0 PWM45 Control Select" "0: Generated SM0PWM45 signal is used by the..,1: Inverted generated SM0PWM45 signal is used by..,2: SWCOUT[SM0OUT45] is used by the deadtime logic.,3: PWM0_EXTB signal is used by the deadtime logic." line.word 0x8 "MCTRL,Master Control Register" hexmask.word.byte 0x8 12.--15. 1. "IPOL,Current Polarity" hexmask.word.byte 0x8 8.--11. 1. "RUN,Run" newline hexmask.word.byte 0x8 4.--7. 1. "CLDOK,Clear Load Okay" hexmask.word.byte 0x8 0.--3. 1. "LDOK,Load Okay" line.word 0xA "MCTRL2,Master Control 2 Register" bitfld.word 0xA 0.--1. "MONPLL,Monitor PLL State" "0: Not locked. Do not monitor PLL operation.,1: Not locked. Monitor PLL operation to..,2: Locked. Do not monitor PLL operation. Resetting..,3: Locked. Monitor PLL operation to automatically.." line.word 0xC "FCTRL0,Fault Control Register" hexmask.word.byte 0xC 12.--15. 1. "FLVL,Fault Level" hexmask.word.byte 0xC 8.--11. 1. "FAUTO,Automatic Fault Clearing" newline hexmask.word.byte 0xC 4.--7. 1. "FSAFE,Fault Safety Mode" hexmask.word.byte 0xC 0.--3. 1. "FIE,Fault Interrupt Enables" line.word 0xE "FSTS0,Fault Status Register" hexmask.word.byte 0xE 12.--15. 1. "FHALF,Half Cycle Fault Recovery" hexmask.word.byte 0xE 8.--11. 1. "FFPIN,Filtered Fault Pins" newline hexmask.word.byte 0xE 4.--7. 1. "FFULL,Full Cycle" hexmask.word.byte 0xE 0.--3. 1. "FFLAG,Fault Flags" line.word 0x10 "FFILT0,Fault Filter Register" bitfld.word 0x10 15. "GSTR,Fault Glitch Stretch Enable" "0: Fault input glitch stretching is disabled.,1: Input fault signals will be stretched to at.." bitfld.word 0x10 8.--10. "FILT_CNT,Fault Filter Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x10 0.--7. 1. "FILT_PER,Fault Filter Period" line.word 0x12 "FTST0,Fault Test Register" bitfld.word 0x12 0. "FTEST,Fault Test" "0: No fault,1: Cause a simulated fault" line.word 0x14 "FCTRL20,Fault Control 2 Register" hexmask.word.byte 0x14 0.--3. 1. "NOCOMB,No Combinational Path From Fault Input To PWM Output" tree.end tree "PWM4" base ad:0x40198000 repeat 4. (list 0x0 0x1 0x2 0x3)(list ad:0x40198000 ad:0x40198060 ad:0x401980C0 ad:0x40198120) tree "SM[$1]" base $2 rgroup.word ($2)++0x1 line.word 0x0 "SMCNT,Counter Register" hexmask.word 0x0 0.--15. 1. "CNT,Counter Register Bits" group.word ($2+0x2)++0x5 line.word 0x0 "SMINIT,Initial Count Register" hexmask.word 0x0 0.--15. 1. "INIT,Initial Count Register Bits" line.word 0x2 "SMCTRL2,Control 2 Register" bitfld.word 0x2 15. "DBGEN,Debug Enable" "0,1" bitfld.word 0x2 14. "WAITEN,WAIT Enable" "0,1" newline bitfld.word 0x2 13. "INDEP,Independent or Complementary Pair Operation" "0: PWM_A and PWM_B form a complementary PWM pair.,1: PWM_A and PWM_B outputs are independent PWMs." bitfld.word 0x2 12. "PWM23_INIT,PWM23 Initial Value" "0,1" newline bitfld.word 0x2 11. "PWM45_INIT,PWM45 Initial Value" "0,1" bitfld.word 0x2 10. "PWMX_INIT,PWM_X Initial Value" "0,1" newline bitfld.word 0x2 8.--9. "INIT_SEL,Initialization Control Select" "0: Local sync (PWM_X) causes initialization.,1: Master reload from submodule 0 causes..,2: Master sync from submodule 0 causes..,3: EXT_SYNC causes initialization." bitfld.word 0x2 7. "FRCEN,FRCEN" "0: Initialization from a FORCE_OUT is disabled.,1: Initialization from a FORCE_OUT is enabled." newline bitfld.word 0x2 6. "FORCE,Force Initialization" "0,1" bitfld.word 0x2 3.--5. "FORCE_SEL,This read/write bit determines the source of the FORCE OUTPUT signal for this submodule." "0: The local force signal CTRL2[FORCE] from this..,1: The master force signal from submodule 0 is used..,2: The local reload signal from this submodule is..,3: The master reload signal from submodule0 is used..,4: The local sync signal from this submodule is..,5: The master sync signal from submodule0 is used..,6: The external force signal EXT_FORCE from outside..,7: The external sync signal EXT_SYNC from outside.." newline bitfld.word 0x2 2. "RELOAD_SEL,Reload Source Select" "0: The local RELOAD signal is used to reload..,1: The master RELOAD signal (from submodule 0) is.." bitfld.word 0x2 0.--1. "CLK_SEL,Clock Source Select" "0: The IPBus clock is used as the clock for the..,1: EXT_CLK is used as the clock for the local..,2: Submodule 0's clock (AUX_CLK) is used as the..,?" line.word 0x4 "SMCTRL,Control Register" hexmask.word.byte 0x4 12.--15. 1. "LDFQ,Load Frequency" bitfld.word 0x4 11. "HALF,Half Cycle Reload" "0: Half-cycle reloads disabled.,1: Half-cycle reloads enabled." newline bitfld.word 0x4 10. "FULL,Full Cycle Reload" "0: Full-cycle reloads disabled.,1: Full-cycle reloads enabled." rbitfld.word 0x4 8.--9. "DT,Deadtime" "0,1,2,3" newline bitfld.word 0x4 7. "COMPMODE,Compare Mode" "0: The VAL* registers and the PWM counter are..,1: The VAL* registers and the PWM counter are.." bitfld.word 0x4 4.--6. "PRSC,Prescaler" "0: Prescaler 1,1: Prescaler 2,2: Prescaler 4,3: Prescaler 8,4: Prescaler 16,5: Prescaler 32,6: Prescaler 64,7: Prescaler 128" newline bitfld.word 0x4 3. "SPLIT,Split the DBLPWM signal to PWMA and PWMB" "0: DBLPWM is not split. PWMA and PWMB each have..,1: DBLPWM is split to PWMA and PWMB." bitfld.word 0x4 2. "LDMOD,Load Mode Select" "0: Buffered registers of this submodule are loaded..,1: Buffered registers of this submodule are loaded.." newline bitfld.word 0x4 1. "DBLX,PWMX Double Switching Enable" "0: PWMX double pulse disabled.,1: PWMX double pulse enabled." bitfld.word 0x4 0. "DBLEN,Double Switching Enable" "0: Double switching disabled.,1: Double switching enabled." group.word ($2+0xA)++0x23 line.word 0x0 "SMVAL0,Value Register 0" hexmask.word 0x0 0.--15. 1. "VAL0,Value Register 0" line.word 0x2 "SMFRACVAL1,Fractional Value Register 1" hexmask.word.byte 0x2 11.--15. 1. "FRACVAL1,Fractional Value 1 Register" line.word 0x4 "SMVAL1,Value Register 1" hexmask.word 0x4 0.--15. 1. "VAL1,Value Register 1" line.word 0x6 "SMFRACVAL2,Fractional Value Register 2" hexmask.word.byte 0x6 11.--15. 1. "FRACVAL2,Fractional Value 2" line.word 0x8 "SMVAL2,Value Register 2" hexmask.word 0x8 0.--15. 1. "VAL2,Value Register 2" line.word 0xA "SMFRACVAL3,Fractional Value Register 3" hexmask.word.byte 0xA 11.--15. 1. "FRACVAL3,Fractional Value 3" line.word 0xC "SMVAL3,Value Register 3" hexmask.word 0xC 0.--15. 1. "VAL3,Value Register 3" line.word 0xE "SMFRACVAL4,Fractional Value Register 4" hexmask.word.byte 0xE 11.--15. 1. "FRACVAL4,Fractional Value 4" line.word 0x10 "SMVAL4,Value Register 4" hexmask.word 0x10 0.--15. 1. "VAL4,Value Register 4" line.word 0x12 "SMFRACVAL5,Fractional Value Register 5" hexmask.word.byte 0x12 11.--15. 1. "FRACVAL5,Fractional Value 5" line.word 0x14 "SMVAL5,Value Register 5" hexmask.word 0x14 0.--15. 1. "VAL5,Value Register 5" line.word 0x16 "SMFRCTRL,Fractional Control Register" rbitfld.word 0x16 15. "TEST,Test Status Bit" "0,1" bitfld.word 0x16 4. "FRAC45_EN,Fractional Cycle Placement Enable for PWM_B" "0: Disable fractional cycle placement for PWM_B.,1: Enable fractional cycle placement for PWM_B." newline bitfld.word 0x16 2. "FRAC23_EN,Fractional Cycle Placement Enable for PWM_A" "0: Disable fractional cycle placement for PWM_A.,1: Enable fractional cycle placement for PWM_A." bitfld.word 0x16 1. "FRAC1_EN,Fractional Cycle PWM Period Enable" "0: Disable fractional cycle length for the PWM..,1: Enable fractional cycle length for the PWM period." line.word 0x18 "SMOCTRL,Output Control Register" rbitfld.word 0x18 15. "PWMA_IN,PWM_A Input" "0,1" rbitfld.word 0x18 14. "PWMB_IN,PWM_B Input" "0,1" newline rbitfld.word 0x18 13. "PWMX_IN,PWM_X Input" "0,1" bitfld.word 0x18 10. "POLA,PWM_A Output Polarity" "0: PWM_A output not inverted. A high level on the..,1: PWM_A output inverted. A low level on the PWM_A.." newline bitfld.word 0x18 9. "POLB,PWM_B Output Polarity" "0: PWM_B output not inverted. A high level on the..,1: PWM_B output inverted. A low level on the PWM_B.." bitfld.word 0x18 8. "POLX,PWM_X Output Polarity" "0: PWM_X output not inverted. A high level on the..,1: PWM_X output inverted. A low level on the PWM_X.." newline bitfld.word 0x18 4.--5. "PWMAFS,PWM_A Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." bitfld.word 0x18 2.--3. "PWMBFS,PWM_B Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." newline bitfld.word 0x18 0.--1. "PWMXFS,PWM_X Fault State" "0: Output is forced to logic 0 state prior to..,1: Output is forced to logic 1 state prior to..,2: Output is tristated.,3: Output is tristated." line.word 0x1A "SMSTS,Status Register" rbitfld.word 0x1A 14. "RUF,Registers Updated Flag" "0: No register update has occurred since last reload.,1: At least one of the double buffered registers.." eventfld.word 0x1A 13. "REF,Reload Error Flag" "0: No reload error occurred.,1: Reload signal occurred with non-coherent data.." newline eventfld.word 0x1A 12. "RF,Reload Flag" "0: No new reload cycle since last STS[RF] clearing,1: New reload cycle since last STS[RF] clearing" eventfld.word 0x1A 11. "CFA1,Capture Flag A1" "0,1" newline eventfld.word 0x1A 10. "CFA0,Capture Flag A0" "0,1" eventfld.word 0x1A 9. "CFB1,Capture Flag B1" "0,1" newline eventfld.word 0x1A 8. "CFB0,Capture Flag B0" "0,1" eventfld.word 0x1A 7. "CFX1,Capture Flag X1" "0,1" newline eventfld.word 0x1A 6. "CFX0,Capture Flag X0" "0,1" hexmask.word.byte 0x1A 0.--5. 1. "CMPF,Compare Flags" line.word 0x1C "SMINTEN,Interrupt Enable Register" bitfld.word 0x1C 13. "REIE,Reload Error Interrupt Enable" "0: STS[REF] CPU interrupt requests disabled,1: STS[REF] CPU interrupt requests enabled" bitfld.word 0x1C 12. "RIE,Reload Interrupt Enable" "0: STS[RF] CPU interrupt requests disabled,1: STS[RF] CPU interrupt requests enabled" newline bitfld.word 0x1C 11. "CA1IE,Capture A 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFA1].,1: Interrupt request enabled for STS[CFA1]." bitfld.word 0x1C 10. "CA0IE,Capture A 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFA0].,1: Interrupt request enabled for STS[CFA0]." newline bitfld.word 0x1C 9. "CB1IE,Capture B 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFB1].,1: Interrupt request enabled for STS[CFB1]." bitfld.word 0x1C 8. "CB0IE,Capture B 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFB0].,1: Interrupt request enabled for STS[CFB0]." newline bitfld.word 0x1C 7. "CX1IE,Capture X 1 Interrupt Enable" "0: Interrupt request disabled for STS[CFX1].,1: Interrupt request enabled for STS[CFX1]." bitfld.word 0x1C 6. "CX0IE,Capture X 0 Interrupt Enable" "0: Interrupt request disabled for STS[CFX0].,1: Interrupt request enabled for STS[CFX0]." newline hexmask.word.byte 0x1C 0.--5. 1. "CMPIE,Compare Interrupt Enables" line.word 0x1E "SMDMAEN,DMA Enable Register" bitfld.word 0x1E 9. "VALDE,Value Registers DMA Enable" "0: DMA write requests disabled,1: Enabled" bitfld.word 0x1E 8. "FAND,FIFO Watermark AND Control" "0: Selected FIFO watermarks are OR'ed together.,1: Selected FIFO watermarks are AND'ed together." newline bitfld.word 0x1E 6.--7. "CAPTDE,Capture DMA Enable Source Select" "0: Read DMA requests disabled.,1: Exceeding a FIFO watermark sets the DMA read..,2: A local sync (VAL1 matches counter) sets the..,3: A local reload (STS[RF] being set) sets the read.." bitfld.word 0x1E 5. "CA1DE,Capture A1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 4. "CA0DE,Capture A0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 3. "CB1DE,Capture B1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 2. "CB0DE,Capture B0 FIFO DMA Enable" "0,1" bitfld.word 0x1E 1. "CX1DE,Capture X1 FIFO DMA Enable" "0,1" newline bitfld.word 0x1E 0. "CX0DE,Capture X0 FIFO DMA Enable" "0,1" line.word 0x20 "SMTCTRL,Output Trigger Control Register" bitfld.word 0x20 15. "PWAOT0,Output Trigger 0 Source Select" "0: Route the PWM_OUT_TRIG0 signal to PWM_OUT_TRIG0..,1: Route the PWMA output to the PWM_OUT_TRIG0 port." bitfld.word 0x20 14. "PWBOT1,Output Trigger 1 Source Select" "0: Route the PWM_OUT_TRIG1 signal to PWM_OUT_TRIG1..,1: Route the PWMB output to the PWM_OUT_TRIG1 port." newline bitfld.word 0x20 12. "TRGFRQ,Trigger frequency" "0: Trigger outputs are generated during every PWM..,1: Trigger outputs are generated only during the.." hexmask.word.byte 0x20 0.--5. 1. "OUT_TRIG_EN,Output Trigger Enables" line.word 0x22 "SMDISMAP0,Fault Disable Mapping Register 0" hexmask.word.byte 0x22 8.--11. 1. "DIS0X,PWM_X Fault Disable Mask 0" hexmask.word.byte 0x22 4.--7. 1. "DIS0B,PWM_B Fault Disable Mask 0" newline hexmask.word.byte 0x22 0.--3. 1. "DIS0A,PWM_A Fault Disable Mask 0" group.word ($2+0x30)++0xF line.word 0x0 "SMDTCNT0,Deadtime Count Register 0" hexmask.word 0x0 0.--15. 1. "DTCNT0,DTCNT0" line.word 0x2 "SMDTCNT1,Deadtime Count Register 1" hexmask.word 0x2 0.--15. 1. "DTCNT1,DTCNT1" line.word 0x4 "SMCAPTCTRLA,Capture Control A Register" rbitfld.word 0x4 13.--15. "CA1CNT,Capture A1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x4 10.--12. "CA0CNT,Capture A0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x4 8.--9. "CFAWM,Capture A FIFOs Water Mark" "0,1,2,3" bitfld.word 0x4 7. "EDGCNTA_EN,Edge Counter A Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x4 6. "INP_SELA,Input Select A" "0: Raw PWM_A input signal selected as source.,1: Edge Counter" bitfld.word 0x4 4.--5. "EDGA1,Edge A 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x4 2.--3. "EDGA0,Edge A 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x4 1. "ONESHOTA,One Shot Mode A" "0: Free Running,1: One Shot" newline bitfld.word 0x4 0. "ARMA,Arm A" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0x6 "SMCAPTCOMPA,Capture Compare A Register" hexmask.word.byte 0x6 8.--15. 1. "EDGCNTA,Edge Counter A" hexmask.word.byte 0x6 0.--7. 1. "EDGCMPA,Edge Compare A" line.word 0x8 "SMCAPTCTRLB,Capture Control B Register" rbitfld.word 0x8 13.--15. "CB1CNT,Capture B1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0x8 10.--12. "CB0CNT,Capture B0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0x8 8.--9. "CFBWM,Capture B FIFOs Water Mark" "0,1,2,3" bitfld.word 0x8 7. "EDGCNTB_EN,Edge Counter B Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0x8 6. "INP_SELB,Input Select B" "0: Raw PWM_B input signal selected as source.,1: Edge Counter" bitfld.word 0x8 4.--5. "EDGB1,Edge B 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0x8 2.--3. "EDGB0,Edge B 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0x8 1. "ONESHOTB,One Shot Mode B" "0: Free Running,1: One Shot" newline bitfld.word 0x8 0. "ARMB,Arm B" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xA "SMCAPTCOMPB,Capture Compare B Register" hexmask.word.byte 0xA 8.--15. 1. "EDGCNTB,Edge Counter B" hexmask.word.byte 0xA 0.--7. 1. "EDGCMPB,Edge Compare B" line.word 0xC "SMCAPTCTRLX,Capture Control X Register" rbitfld.word 0xC 13.--15. "CX1CNT,Capture X1 FIFO Word Count" "0,1,2,3,4,5,6,7" rbitfld.word 0xC 10.--12. "CX0CNT,Capture X0 FIFO Word Count" "0,1,2,3,4,5,6,7" newline bitfld.word 0xC 8.--9. "CFXWM,Capture X FIFOs Water Mark" "0,1,2,3" bitfld.word 0xC 7. "EDGCNTX_EN,Edge Counter X Enable" "0: Edge counter disabled and held in reset,1: Edge counter enabled" newline bitfld.word 0xC 6. "INP_SELX,Input Select X" "0: Raw PWM_X input signal selected as source.,1: Edge Counter" bitfld.word 0xC 4.--5. "EDGX1,Edge X 1" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" newline bitfld.word 0xC 2.--3. "EDGX0,Edge X 0" "0: Disabled,1: Capture falling edges,2: Capture rising edges,3: Capture any edge" bitfld.word 0xC 1. "ONESHOTX,One Shot Mode Aux" "0: Free Running,1: One Shot" newline bitfld.word 0xC 0. "ARMX,Arm X" "0: Input capture operation is disabled.,1: Input capture operation as specified by.." line.word 0xE "SMCAPTCOMPX,Capture Compare X Register" hexmask.word.byte 0xE 8.--15. 1. "EDGCNTX,Edge Counter X" hexmask.word.byte 0xE 0.--7. 1. "EDGCMPX,Edge Compare X" rgroup.word ($2+0x40)++0x17 line.word 0x0 "SMCVAL0,Capture Value 0 Register" hexmask.word 0x0 0.--15. 1. "CAPTVAL0,CAPTVAL0" line.word 0x2 "SMCVAL0CYC,Capture Value 0 Cycle Register" hexmask.word.byte 0x2 0.--3. 1. "CVAL0CYC,CVAL0CYC" line.word 0x4 "SMCVAL1,Capture Value 1 Register" hexmask.word 0x4 0.--15. 1. "CAPTVAL1,CAPTVAL1" line.word 0x6 "SMCVAL1CYC,Capture Value 1 Cycle Register" hexmask.word.byte 0x6 0.--3. 1. "CVAL1CYC,CVAL1CYC" line.word 0x8 "SMCVAL2,Capture Value 2 Register" hexmask.word 0x8 0.--15. 1. "CAPTVAL2,CAPTVAL2" line.word 0xA "SMCVAL2CYC,Capture Value 2 Cycle Register" hexmask.word.byte 0xA 0.--3. 1. "CVAL2CYC,CVAL2CYC" line.word 0xC "SMCVAL3,Capture Value 3 Register" hexmask.word 0xC 0.--15. 1. "CAPTVAL3,CAPTVAL3" line.word 0xE "SMCVAL3CYC,Capture Value 3 Cycle Register" hexmask.word.byte 0xE 0.--3. 1. "CVAL3CYC,CVAL3CYC" line.word 0x10 "SMCVAL4,Capture Value 4 Register" hexmask.word 0x10 0.--15. 1. "CAPTVAL4,CAPTVAL4" line.word 0x12 "SMCVAL4CYC,Capture Value 4 Cycle Register" hexmask.word.byte 0x12 0.--3. 1. "CVAL4CYC,CVAL4CYC" line.word 0x14 "SMCVAL5,Capture Value 5 Register" hexmask.word 0x14 0.--15. 1. "CAPTVAL5,CAPTVAL5" line.word 0x16 "SMCVAL5CYC,Capture Value 5 Cycle Register" hexmask.word.byte 0x16 0.--3. 1. "CVAL5CYC,CVAL5CYC" tree.end repeat.end base ad:0x40198000 group.word 0x180++0x15 line.word 0x0 "OUTEN,Output Enable Register" hexmask.word.byte 0x0 8.--11. 1. "PWMA_EN,PWM_A Output Enables" hexmask.word.byte 0x0 4.--7. 1. "PWMB_EN,PWM_B Output Enables" newline hexmask.word.byte 0x0 0.--3. 1. "PWMX_EN,PWM_X Output Enables" line.word 0x2 "MASK,Mask Register" hexmask.word.byte 0x2 8.--11. 1. "MASKA,PWM_A Masks" hexmask.word.byte 0x2 4.--7. 1. "MASKB,PWM_B Masks" newline hexmask.word.byte 0x2 0.--3. 1. "MASKX,PWM_X Masks" line.word 0x4 "SWCOUT,Software Controlled Output Register" bitfld.word 0x4 7. "SM3OUT23,Submodule 3 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 6. "SM3OUT45,Submodule 3 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 5. "SM2OUT23,Submodule 2 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 4. "SM2OUT45,Submodule 2 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 3. "SM1OUT23,Submodule 1 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 2. "SM1OUT45,Submodule 1 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." newline bitfld.word 0x4 1. "SM0OUT23,Submodule 0 Software Controlled Output 23" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." bitfld.word 0x4 0. "SM0OUT45,Submodule 0 Software Controlled Output 45" "0: A logic 0 is supplied to the deadtime generator..,1: A logic 1 is supplied to the deadtime generator.." line.word 0x6 "DTSRCSEL,PWM Source Select Register" bitfld.word 0x6 14.--15. "SM3SEL23,Submodule 3 PWM23 Control Select" "0: Generated SM3PWM23 signal is used by the..,1: Inverted generated SM3PWM23 signal is used by..,2: SWCOUT[SM3OUT23] is used by the deadtime logic.,3: PWM3_EXTA signal is used by the deadtime logic." bitfld.word 0x6 12.--13. "SM3SEL45,Submodule 3 PWM45 Control Select" "0: Generated SM3PWM45 signal is used by the..,1: Inverted generated SM3PWM45 signal is used by..,2: SWCOUT[SM3OUT45] is used by the deadtime logic.,3: PWM3_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 10.--11. "SM2SEL23,Submodule 2 PWM23 Control Select" "0: Generated SM2PWM23 signal is used by the..,1: Inverted generated SM2PWM23 signal is used by..,2: SWCOUT[SM2OUT23] is used by the deadtime logic.,3: PWM2_EXTA signal is used by the deadtime logic." bitfld.word 0x6 8.--9. "SM2SEL45,Submodule 2 PWM45 Control Select" "0: Generated SM2PWM45 signal is used by the..,1: Inverted generated SM2PWM45 signal is used by..,2: SWCOUT[SM2OUT45] is used by the deadtime logic.,3: PWM2_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 6.--7. "SM1SEL23,Submodule 1 PWM23 Control Select" "0: Generated SM1PWM23 signal is used by the..,1: Inverted generated SM1PWM23 signal is used by..,2: SWCOUT[SM1OUT23] is used by the deadtime logic.,3: PWM1_EXTA signal is used by the deadtime logic." bitfld.word 0x6 4.--5. "SM1SEL45,Submodule 1 PWM45 Control Select" "0: Generated SM1PWM45 signal is used by the..,1: Inverted generated SM1PWM45 signal is used by..,2: SWCOUT[SM1OUT45] is used by the deadtime logic.,3: PWM1_EXTB signal is used by the deadtime logic." newline bitfld.word 0x6 2.--3. "SM0SEL23,Submodule 0 PWM23 Control Select" "0: Generated SM0PWM23 signal is used by the..,1: Inverted generated SM0PWM23 signal is used by..,2: SWCOUT[SM0OUT23] is used by the deadtime logic.,3: PWM0_EXTA signal is used by the deadtime logic." bitfld.word 0x6 0.--1. "SM0SEL45,Submodule 0 PWM45 Control Select" "0: Generated SM0PWM45 signal is used by the..,1: Inverted generated SM0PWM45 signal is used by..,2: SWCOUT[SM0OUT45] is used by the deadtime logic.,3: PWM0_EXTB signal is used by the deadtime logic." line.word 0x8 "MCTRL,Master Control Register" hexmask.word.byte 0x8 12.--15. 1. "IPOL,Current Polarity" hexmask.word.byte 0x8 8.--11. 1. "RUN,Run" newline hexmask.word.byte 0x8 4.--7. 1. "CLDOK,Clear Load Okay" hexmask.word.byte 0x8 0.--3. 1. "LDOK,Load Okay" line.word 0xA "MCTRL2,Master Control 2 Register" bitfld.word 0xA 0.--1. "MONPLL,Monitor PLL State" "0: Not locked. Do not monitor PLL operation.,1: Not locked. Monitor PLL operation to..,2: Locked. Do not monitor PLL operation. Resetting..,3: Locked. Monitor PLL operation to automatically.." line.word 0xC "FCTRL0,Fault Control Register" hexmask.word.byte 0xC 12.--15. 1. "FLVL,Fault Level" hexmask.word.byte 0xC 8.--11. 1. "FAUTO,Automatic Fault Clearing" newline hexmask.word.byte 0xC 4.--7. 1. "FSAFE,Fault Safety Mode" hexmask.word.byte 0xC 0.--3. 1. "FIE,Fault Interrupt Enables" line.word 0xE "FSTS0,Fault Status Register" hexmask.word.byte 0xE 12.--15. 1. "FHALF,Half Cycle Fault Recovery" hexmask.word.byte 0xE 8.--11. 1. "FFPIN,Filtered Fault Pins" newline hexmask.word.byte 0xE 4.--7. 1. "FFULL,Full Cycle" hexmask.word.byte 0xE 0.--3. 1. "FFLAG,Fault Flags" line.word 0x10 "FFILT0,Fault Filter Register" bitfld.word 0x10 15. "GSTR,Fault Glitch Stretch Enable" "0: Fault input glitch stretching is disabled.,1: Input fault signals will be stretched to at.." bitfld.word 0x10 8.--10. "FILT_CNT,Fault Filter Count" "0,1,2,3,4,5,6,7" newline hexmask.word.byte 0x10 0.--7. 1. "FILT_PER,Fault Filter Period" line.word 0x12 "FTST0,Fault Test Register" bitfld.word 0x12 0. "FTEST,Fault Test" "0: No fault,1: Cause a simulated fault" line.word 0x14 "FCTRL20,Fault Control 2 Register" hexmask.word.byte 0x14 0.--3. 1. "NOCOMB,No Combinational Path From Fault Input To PWM Output" tree.end tree.end sif (cpuis("IMXRT1166-CM4")||cpuis("IMXRT1166-CM7")) tree "PXP" base ad:0x40814000 group.long 0x0++0x33 line.long 0x0 "CTRL,Control Register 0" bitfld.long 0x0 31. "SFTRST,This bit can be turned on and then off to reset the PXP block to its default state." "0: Normal PXP operation is enabled,1: Clocking with PXP is disabled and held in its.." newline bitfld.long 0x0 30. "CLKGATE,This bit must be set to zero for normal operation" "0: Normal operation,1: All clocks to PXP is gated-off" newline bitfld.long 0x0 28. "EN_REPEAT,Enable the PXP to run continuously" "0: PXP will complete the process and enter the idle..,1: PXP will repeat based on the current.." newline bitfld.long 0x0 23. "BLOCK_SIZE,Select the block size to process." "0: Process 8x8 pixel blocks.,1: Process 16x16 pixel blocks." newline bitfld.long 0x0 22. "ROT_POS,This bit controls where rotation will occur in the PXP datapath" "0,1" newline bitfld.long 0x0 11. "VFLIP,Indicates that the output buffer should be flipped vertically (effect applied before rotation)." "0: Vertical Flip is disabled,1: Vertical Flip is enabled" newline bitfld.long 0x0 10. "HFLIP,Indicates that the output buffer should be flipped horizontally (effect applied before rotation)." "0: Horizontal Flip is disabled,1: Horizontal Flip is enabled" newline bitfld.long 0x0 8.--9. "ROTATE,Indicates the clockwise rotation to be applied at the output buffer" "0: ROT_0,1: ROT_90,2: ROT_180,3: ROT_270" newline bitfld.long 0x0 4. "ENABLE_LCD_HANDSHAKE,Enable handshake with LCD controller" "0,1" newline bitfld.long 0x0 2. "NEXT_IRQ_ENABLE,Next command interrupt enable" "0: Disabled,1: Enabled" newline bitfld.long 0x0 1. "IRQ_ENABLE,Interrupt enable When using the PXP_NEXT functionality to reprogram the PXP the new value of this bit will be used and may therefore enable or disable an interrupt unintentionally" "0: PXP interrupt is disabled,1: PXP interrupt is enabled" newline bitfld.long 0x0 0. "ENABLE,Enables PXP operation with specified parameters" "0: PXP is disabled,1: PXP is enabled" line.long 0x4 "CTRL_SET,Control Register 0" bitfld.long 0x4 31. "SFTRST,This bit can be turned on and then off to reset the PXP block to its default state." "0: Normal PXP operation is enabled,1: Clocking with PXP is disabled and held in its.." newline bitfld.long 0x4 30. "CLKGATE,This bit must be set to zero for normal operation" "0: Normal operation,1: All clocks to PXP is gated-off" newline bitfld.long 0x4 28. "EN_REPEAT,Enable the PXP to run continuously" "0: PXP will complete the process and enter the idle..,1: PXP will repeat based on the current.." newline bitfld.long 0x4 23. "BLOCK_SIZE,Select the block size to process." "0: Process 8x8 pixel blocks.,1: Process 16x16 pixel blocks." newline bitfld.long 0x4 22. "ROT_POS,This bit controls where rotation will occur in the PXP datapath" "0,1" newline bitfld.long 0x4 11. "VFLIP,Indicates that the output buffer should be flipped vertically (effect applied before rotation)." "0: Vertical Flip is disabled,1: Vertical Flip is enabled" newline bitfld.long 0x4 10. "HFLIP,Indicates that the output buffer should be flipped horizontally (effect applied before rotation)." "0: Horizontal Flip is disabled,1: Horizontal Flip is enabled" newline bitfld.long 0x4 8.--9. "ROTATE,Indicates the clockwise rotation to be applied at the output buffer" "0: ROT_0,1: ROT_90,2: ROT_180,3: ROT_270" newline bitfld.long 0x4 4. "ENABLE_LCD_HANDSHAKE,Enable handshake with LCD controller" "0,1" newline bitfld.long 0x4 2. "NEXT_IRQ_ENABLE,Next command interrupt enable" "0: Disabled,1: Enabled" newline bitfld.long 0x4 1. "IRQ_ENABLE,Interrupt enable When using the PXP_NEXT functionality to reprogram the PXP the new value of this bit will be used and may therefore enable or disable an interrupt unintentionally" "0: PXP interrupt is disabled,1: PXP interrupt is enabled" newline bitfld.long 0x4 0. "ENABLE,Enables PXP operation with specified parameters" "0: PXP is disabled,1: PXP is enabled" line.long 0x8 "CTRL_CLR,Control Register 0" bitfld.long 0x8 31. "SFTRST,This bit can be turned on and then off to reset the PXP block to its default state." "0: Normal PXP operation is enabled,1: Clocking with PXP is disabled and held in its.." newline bitfld.long 0x8 30. "CLKGATE,This bit must be set to zero for normal operation" "0: Normal operation,1: All clocks to PXP is gated-off" newline bitfld.long 0x8 28. "EN_REPEAT,Enable the PXP to run continuously" "0: PXP will complete the process and enter the idle..,1: PXP will repeat based on the current.." newline bitfld.long 0x8 23. "BLOCK_SIZE,Select the block size to process." "0: Process 8x8 pixel blocks.,1: Process 16x16 pixel blocks." newline bitfld.long 0x8 22. "ROT_POS,This bit controls where rotation will occur in the PXP datapath" "0,1" newline bitfld.long 0x8 11. "VFLIP,Indicates that the output buffer should be flipped vertically (effect applied before rotation)." "0: Vertical Flip is disabled,1: Vertical Flip is enabled" newline bitfld.long 0x8 10. "HFLIP,Indicates that the output buffer should be flipped horizontally (effect applied before rotation)." "0: Horizontal Flip is disabled,1: Horizontal Flip is enabled" newline bitfld.long 0x8 8.--9. "ROTATE,Indicates the clockwise rotation to be applied at the output buffer" "0: ROT_0,1: ROT_90,2: ROT_180,3: ROT_270" newline bitfld.long 0x8 4. "ENABLE_LCD_HANDSHAKE,Enable handshake with LCD controller" "0,1" newline bitfld.long 0x8 2. "NEXT_IRQ_ENABLE,Next command interrupt enable" "0: Disabled,1: Enabled" newline bitfld.long 0x8 1. "IRQ_ENABLE,Interrupt enable When using the PXP_NEXT functionality to reprogram the PXP the new value of this bit will be used and may therefore enable or disable an interrupt unintentionally" "0: PXP interrupt is disabled,1: PXP interrupt is enabled" newline bitfld.long 0x8 0. "ENABLE,Enables PXP operation with specified parameters" "0: PXP is disabled,1: PXP is enabled" line.long 0xC "CTRL_TOG,Control Register 0" bitfld.long 0xC 31. "SFTRST,This bit can be turned on and then off to reset the PXP block to its default state." "0: Normal PXP operation is enabled,1: Clocking with PXP is disabled and held in its.." newline bitfld.long 0xC 30. "CLKGATE,This bit must be set to zero for normal operation" "0: Normal operation,1: All clocks to PXP is gated-off" newline bitfld.long 0xC 28. "EN_REPEAT,Enable the PXP to run continuously" "0: PXP will complete the process and enter the idle..,1: PXP will repeat based on the current.." newline bitfld.long 0xC 23. "BLOCK_SIZE,Select the block size to process." "0: Process 8x8 pixel blocks.,1: Process 16x16 pixel blocks." newline bitfld.long 0xC 22. "ROT_POS,This bit controls where rotation will occur in the PXP datapath" "0,1" newline bitfld.long 0xC 11. "VFLIP,Indicates that the output buffer should be flipped vertically (effect applied before rotation)." "0: Vertical Flip is disabled,1: Vertical Flip is enabled" newline bitfld.long 0xC 10. "HFLIP,Indicates that the output buffer should be flipped horizontally (effect applied before rotation)." "0: Horizontal Flip is disabled,1: Horizontal Flip is enabled" newline bitfld.long 0xC 8.--9. "ROTATE,Indicates the clockwise rotation to be applied at the output buffer" "0: ROT_0,1: ROT_90,2: ROT_180,3: ROT_270" newline bitfld.long 0xC 4. "ENABLE_LCD_HANDSHAKE,Enable handshake with LCD controller" "0,1" newline bitfld.long 0xC 2. "NEXT_IRQ_ENABLE,Next command interrupt enable" "0: Disabled,1: Enabled" newline bitfld.long 0xC 1. "IRQ_ENABLE,Interrupt enable When using the PXP_NEXT functionality to reprogram the PXP the new value of this bit will be used and may therefore enable or disable an interrupt unintentionally" "0: PXP interrupt is disabled,1: PXP interrupt is enabled" newline bitfld.long 0xC 0. "ENABLE,Enables PXP operation with specified parameters" "0: PXP is disabled,1: PXP is enabled" line.long 0x10 "STAT,Status Register" hexmask.long.byte 0x10 24.--31. 1. "BLOCKX,Indicates the X coordinate of the block currently being rendered." newline hexmask.long.byte 0x10 16.--23. 1. "BLOCKY,Indicates the X coordinate of the block currently being rendered." newline bitfld.long 0x10 8. "LUT_DMA_LOAD_DONE_IRQ,Indicates that the LUT DMA transfer has completed." "0: LUT DMA LOAD transfer is active,1: LUT DMA LOAD transfer is complete" newline hexmask.long.byte 0x10 4.--7. 1. "AXI_ERROR_ID,Indicates the AXI ID of the failing bus operation." newline bitfld.long 0x10 3. "NEXT_IRQ,Indicates that a command issued with the 'Next Command' functionality has been issued and that a new command may be initiated with a write to the PXP_NEXT register" "0,1" newline bitfld.long 0x10 2. "AXI_READ_ERROR,Indicates PXP encountered an AXI read error and processing has been terminated." "0: AXI read is normal,1: AXI read error has occurred" newline bitfld.long 0x10 1. "AXI_WRITE_ERROR,Indicates PXP encountered an AXI write error and processing has been terminated." "0: AXI write is normal,1: AXI write error has occurred" newline bitfld.long 0x10 0. "IRQ,Indicates current PXP interrupt status" "0: No interrupt,1: Interrupt generated" line.long 0x14 "STAT_SET,Status Register" hexmask.long.byte 0x14 24.--31. 1. "BLOCKX,Indicates the X coordinate of the block currently being rendered." newline hexmask.long.byte 0x14 16.--23. 1. "BLOCKY,Indicates the X coordinate of the block currently being rendered." newline bitfld.long 0x14 8. "LUT_DMA_LOAD_DONE_IRQ,Indicates that the LUT DMA transfer has completed." "0: LUT DMA LOAD transfer is active,1: LUT DMA LOAD transfer is complete" newline hexmask.long.byte 0x14 4.--7. 1. "AXI_ERROR_ID,Indicates the AXI ID of the failing bus operation." newline bitfld.long 0x14 3. "NEXT_IRQ,Indicates that a command issued with the 'Next Command' functionality has been issued and that a new command may be initiated with a write to the PXP_NEXT register" "0,1" newline bitfld.long 0x14 2. "AXI_READ_ERROR,Indicates PXP encountered an AXI read error and processing has been terminated." "0: AXI read is normal,1: AXI read error has occurred" newline bitfld.long 0x14 1. "AXI_WRITE_ERROR,Indicates PXP encountered an AXI write error and processing has been terminated." "0: AXI write is normal,1: AXI write error has occurred" newline bitfld.long 0x14 0. "IRQ,Indicates current PXP interrupt status" "0: No interrupt,1: Interrupt generated" line.long 0x18 "STAT_CLR,Status Register" hexmask.long.byte 0x18 24.--31. 1. "BLOCKX,Indicates the X coordinate of the block currently being rendered." newline hexmask.long.byte 0x18 16.--23. 1. "BLOCKY,Indicates the X coordinate of the block currently being rendered." newline bitfld.long 0x18 8. "LUT_DMA_LOAD_DONE_IRQ,Indicates that the LUT DMA transfer has completed." "0: LUT DMA LOAD transfer is active,1: LUT DMA LOAD transfer is complete" newline hexmask.long.byte 0x18 4.--7. 1. "AXI_ERROR_ID,Indicates the AXI ID of the failing bus operation." newline bitfld.long 0x18 3. "NEXT_IRQ,Indicates that a command issued with the 'Next Command' functionality has been issued and that a new command may be initiated with a write to the PXP_NEXT register" "0,1" newline bitfld.long 0x18 2. "AXI_READ_ERROR,Indicates PXP encountered an AXI read error and processing has been terminated." "0: AXI read is normal,1: AXI read error has occurred" newline bitfld.long 0x18 1. "AXI_WRITE_ERROR,Indicates PXP encountered an AXI write error and processing has been terminated." "0: AXI write is normal,1: AXI write error has occurred" newline bitfld.long 0x18 0. "IRQ,Indicates current PXP interrupt status" "0: No interrupt,1: Interrupt generated" line.long 0x1C "STAT_TOG,Status Register" hexmask.long.byte 0x1C 24.--31. 1. "BLOCKX,Indicates the X coordinate of the block currently being rendered." newline hexmask.long.byte 0x1C 16.--23. 1. "BLOCKY,Indicates the X coordinate of the block currently being rendered." newline bitfld.long 0x1C 8. "LUT_DMA_LOAD_DONE_IRQ,Indicates that the LUT DMA transfer has completed." "0: LUT DMA LOAD transfer is active,1: LUT DMA LOAD transfer is complete" newline hexmask.long.byte 0x1C 4.--7. 1. "AXI_ERROR_ID,Indicates the AXI ID of the failing bus operation." newline bitfld.long 0x1C 3. "NEXT_IRQ,Indicates that a command issued with the 'Next Command' functionality has been issued and that a new command may be initiated with a write to the PXP_NEXT register" "0,1" newline bitfld.long 0x1C 2. "AXI_READ_ERROR,Indicates PXP encountered an AXI read error and processing has been terminated." "0: AXI read is normal,1: AXI read error has occurred" newline bitfld.long 0x1C 1. "AXI_WRITE_ERROR,Indicates PXP encountered an AXI write error and processing has been terminated." "0: AXI write is normal,1: AXI write error has occurred" newline bitfld.long 0x1C 0. "IRQ,Indicates current PXP interrupt status" "0: No interrupt,1: Interrupt generated" line.long 0x20 "OUT_CTRL,Output Buffer Control Register" hexmask.long.byte 0x20 24.--31. 1. "ALPHA,When generating an output buffer with an alpha component the value in this field will be used when enabled to override the alpha passed through the pixel data pipeline" newline bitfld.long 0x20 23. "ALPHA_OUTPUT,Indicates that alpha component in output buffer pixels should be overwritten by PXP_OUT_CTRL[ALPHA]" "0: Retain,1: Overwritten" newline bitfld.long 0x20 8.--9. "INTERLACED_OUTPUT,Determines how the PXP writes it's output data" "0: All data written in progressive format to the..,1: Interlaced output: only data for field 0 is..,2: Interlaced output: only data for field 1 is..,3: Interlaced output: data for field 0 is written.." newline hexmask.long.byte 0x20 0.--4. 1. "FORMAT,Output framebuffer format" line.long 0x24 "OUT_CTRL_SET,Output Buffer Control Register" hexmask.long.byte 0x24 24.--31. 1. "ALPHA,When generating an output buffer with an alpha component the value in this field will be used when enabled to override the alpha passed through the pixel data pipeline" newline bitfld.long 0x24 23. "ALPHA_OUTPUT,Indicates that alpha component in output buffer pixels should be overwritten by PXP_OUT_CTRL[ALPHA]" "0: Retain,1: Overwritten" newline bitfld.long 0x24 8.--9. "INTERLACED_OUTPUT,Determines how the PXP writes it's output data" "0: All data written in progressive format to the..,1: Interlaced output: only data for field 0 is..,2: Interlaced output: only data for field 1 is..,3: Interlaced output: data for field 0 is written.." newline hexmask.long.byte 0x24 0.--4. 1. "FORMAT,Output framebuffer format" line.long 0x28 "OUT_CTRL_CLR,Output Buffer Control Register" hexmask.long.byte 0x28 24.--31. 1. "ALPHA,When generating an output buffer with an alpha component the value in this field will be used when enabled to override the alpha passed through the pixel data pipeline" newline bitfld.long 0x28 23. "ALPHA_OUTPUT,Indicates that alpha component in output buffer pixels should be overwritten by PXP_OUT_CTRL[ALPHA]" "0: Retain,1: Overwritten" newline bitfld.long 0x28 8.--9. "INTERLACED_OUTPUT,Determines how the PXP writes it's output data" "0: All data written in progressive format to the..,1: Interlaced output: only data for field 0 is..,2: Interlaced output: only data for field 1 is..,3: Interlaced output: data for field 0 is written.." newline hexmask.long.byte 0x28 0.--4. 1. "FORMAT,Output framebuffer format" line.long 0x2C "OUT_CTRL_TOG,Output Buffer Control Register" hexmask.long.byte 0x2C 24.--31. 1. "ALPHA,When generating an output buffer with an alpha component the value in this field will be used when enabled to override the alpha passed through the pixel data pipeline" newline bitfld.long 0x2C 23. "ALPHA_OUTPUT,Indicates that alpha component in output buffer pixels should be overwritten by PXP_OUT_CTRL[ALPHA]" "0: Retain,1: Overwritten" newline bitfld.long 0x2C 8.--9. "INTERLACED_OUTPUT,Determines how the PXP writes it's output data" "0: All data written in progressive format to the..,1: Interlaced output: only data for field 0 is..,2: Interlaced output: only data for field 1 is..,3: Interlaced output: data for field 0 is written.." newline hexmask.long.byte 0x2C 0.--4. 1. "FORMAT,Output framebuffer format" line.long 0x30 "OUT_BUF,Output Frame Buffer Pointer" hexmask.long 0x30 0.--31. 1. "ADDR,Current address pointer for the output frame buffer" group.long 0x40++0x3 line.long 0x0 "OUT_BUF2,Output Frame Buffer Pointer #2" hexmask.long 0x0 0.--31. 1. "ADDR,Current address pointer for the output frame buffer" group.long 0x50++0x3 line.long 0x0 "OUT_PITCH,Output Buffer Pitch" hexmask.long.word 0x0 0.--15. 1. "PITCH,Indicates the number of bytes in memory between two vertically adjacent pixels." group.long 0x60++0x3 line.long 0x0 "OUT_LRC,Output Surface Lower Right Coordinate" hexmask.long.word 0x0 16.--29. 1. "X,Indicates number of horizontal PIXELS in the output surface (non-rotated)" newline hexmask.long.word 0x0 0.--13. 1. "Y,Indicates the number of vertical PIXELS in the output surface (non-rotated)" group.long 0x70++0x3 line.long 0x0 "OUT_PS_ULC,Processed Surface Upper Left Coordinate" hexmask.long.word 0x0 16.--29. 1. "X,This field indicates the upper left X-coordinate (in pixels) of the processed surface (PS) in the output buffer" newline hexmask.long.word 0x0 0.--13. 1. "Y,This field indicates the upper left Y-coordinate (in pixels) of the processed surface in the output buffer" group.long 0x80++0x3 line.long 0x0 "OUT_PS_LRC,Processed Surface Lower Right Coordinate" hexmask.long.word 0x0 16.--29. 1. "X,This field indicates the lower right X-coordinate (in pixels) of the processed surface (PS) in the output frame buffer" newline hexmask.long.word 0x0 0.--13. 1. "Y,This field indicates the lower right Y-coordinate (in pixels) of the processed surface in the output frame buffer" group.long 0x90++0x3 line.long 0x0 "OUT_AS_ULC,Alpha Surface Upper Left Coordinate" hexmask.long.word 0x0 16.--29. 1. "X,This field indicates the upper left X-coordinate (in pixels) of the alpha surface (AS) in the output frame buffer" newline hexmask.long.word 0x0 0.--13. 1. "Y,This field indicates the upper left Y-coordinate (in pixels) of the alpha surface in the output frame buffer" group.long 0xA0++0x3 line.long 0x0 "OUT_AS_LRC,Alpha Surface Lower Right Coordinate" hexmask.long.word 0x0 16.--29. 1. "X,This field indicates the lower right X-coordinate (in pixels) of the alpha surface (AS) in the output frame buffer" newline hexmask.long.word 0x0 0.--13. 1. "Y,This field indicates the lower right Y-coordinate (in pixels) of the alpha surface in the output frame buffer" group.long 0xB0++0x13 line.long 0x0 "PS_CTRL,Processed Surface (PS) Control Register" bitfld.long 0x0 10.--11. "DECX,Horizontal pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x0 8.--9. "DECY,Verticle pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x0 6. "WB_SWAP,Swap bytes in words. For each 16 bit word the two bytes will be swapped." "0: Byte swap is disabled,1: Byte swap is enabled" newline hexmask.long.byte 0x0 0.--5. 1. "FORMAT,PS buffer format. To select between YUV and YCbCr formats see bit 31 of the CSC1_COEF0 register." line.long 0x4 "PS_CTRL_SET,Processed Surface (PS) Control Register" bitfld.long 0x4 10.--11. "DECX,Horizontal pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x4 8.--9. "DECY,Verticle pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x4 6. "WB_SWAP,Swap bytes in words. For each 16 bit word the two bytes will be swapped." "0: Byte swap is disabled,1: Byte swap is enabled" newline hexmask.long.byte 0x4 0.--5. 1. "FORMAT,PS buffer format. To select between YUV and YCbCr formats see bit 31 of the CSC1_COEF0 register." line.long 0x8 "PS_CTRL_CLR,Processed Surface (PS) Control Register" bitfld.long 0x8 10.--11. "DECX,Horizontal pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x8 8.--9. "DECY,Verticle pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0x8 6. "WB_SWAP,Swap bytes in words. For each 16 bit word the two bytes will be swapped." "0: Byte swap is disabled,1: Byte swap is enabled" newline hexmask.long.byte 0x8 0.--5. 1. "FORMAT,PS buffer format. To select between YUV and YCbCr formats see bit 31 of the CSC1_COEF0 register." line.long 0xC "PS_CTRL_TOG,Processed Surface (PS) Control Register" bitfld.long 0xC 10.--11. "DECX,Horizontal pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0xC 8.--9. "DECY,Verticle pre decimation filter control." "0: Disable pre-decimation filter.,1: Decimate PS by 2.,2: Decimate PS by 4.,3: Decimate PS by 8." newline bitfld.long 0xC 6. "WB_SWAP,Swap bytes in words. For each 16 bit word the two bytes will be swapped." "0: Byte swap is disabled,1: Byte swap is enabled" newline hexmask.long.byte 0xC 0.--5. 1. "FORMAT,PS buffer format. To select between YUV and YCbCr formats see bit 31 of the CSC1_COEF0 register." line.long 0x10 "PS_BUF,PS Input Buffer Address" hexmask.long 0x10 0.--31. 1. "ADDR,Address pointer for the PS RGB or Y (luma) input buffer." group.long 0xD0++0x3 line.long 0x0 "PS_UBUF,PS U/Cb or 2 Plane UV Input Buffer Address" hexmask.long 0x0 0.--31. 1. "ADDR,Address pointer for the PS U/Cb or 2 plane UV Chroma input buffer." group.long 0xE0++0x3 line.long 0x0 "PS_VBUF,PS V/Cr Input Buffer Address" hexmask.long 0x0 0.--31. 1. "ADDR,Address pointer for the PS V/Cr Chroma input buffer." group.long 0xF0++0x3 line.long 0x0 "PS_PITCH,Processed Surface Pitch" hexmask.long.word 0x0 0.--15. 1. "PITCH,Indicates the number of bytes in memory between two vertically adjacent pixels." group.long 0x100++0x3 line.long 0x0 "PS_BACKGROUND,PS Background Color" hexmask.long.tbyte 0x0 0.--23. 1. "COLOR,Background color (in 24bpp format) for any pixels not within the buffer range specified by the PS ULC/LRC" group.long 0x110++0x3 line.long 0x0 "PS_SCALE,PS Scale Factor Register" hexmask.long.word 0x0 16.--30. 1. "YSCALE,This is a two bit integer and 12 bit fractional representation (##" newline hexmask.long.word 0x0 0.--14. 1. "XSCALE,This is a two bit integer and 12 bit fractional representation (##" group.long 0x120++0x3 line.long 0x0 "PS_OFFSET,PS Scale Offset Register" hexmask.long.word 0x0 16.--27. 1. "YOFFSET,This is a 12 bit fractional representation (0" newline hexmask.long.word 0x0 0.--11. 1. "XOFFSET,This is a 12 bit fractional representation (0" group.long 0x130++0x3 line.long 0x0 "PS_CLRKEYLOW,PS Color Key Low" hexmask.long.tbyte 0x0 0.--23. 1. "PIXEL,Low range of color key applied to PS buffer" group.long 0x140++0x3 line.long 0x0 "PS_CLRKEYHIGH,PS Color Key High" hexmask.long.tbyte 0x0 0.--23. 1. "PIXEL,High range of color key applied to PS buffer" group.long 0x150++0x3 line.long 0x0 "AS_CTRL,Alpha Surface Control" bitfld.long 0x0 20. "ALPHA_INVERT,Setting this bit to logic 0 will not alter the alpha value" "0: Not inverted,1: Inverted" newline hexmask.long.byte 0x0 16.--19. 1. "ROP,Indicates a raster operation to perform when enabled" newline hexmask.long.byte 0x0 8.--15. 1. "ALPHA,Alpha modifier used when the ALPHA_MULTIPLY or ALPHA_OVERRIDE values are programmed in PXP_AS_CTRL[ALPHA_CTRL]" newline hexmask.long.byte 0x0 4.--7. 1. "FORMAT,Indicates the input buffer format for AS." newline bitfld.long 0x0 3. "ENABLE_COLORKEY,Indicates that colorkey functionality is enabled for this alpha surface" "0: Disabled,1: Enabled" newline bitfld.long 0x0 1.--2. "ALPHA_CTRL,Determines how the alpha value is constructed for this alpha surface" "0: Indicates that the AS pixel alpha value will be..,1: Indicates that the value in the ALPHA field..,2: Indicates that the value in the ALPHA field..,3: Enable ROPs. The ROP field indicates an.." group.long 0x160++0x3 line.long 0x0 "AS_BUF,Alpha Surface Buffer Pointer" hexmask.long 0x0 0.--31. 1. "ADDR,Address pointer for the alpha surface 0 buffer." group.long 0x170++0x3 line.long 0x0 "AS_PITCH,Alpha Surface Pitch" hexmask.long.word 0x0 0.--15. 1. "PITCH,Indicates the number of bytes in memory between two vertically adjacent pixels." group.long 0x180++0x3 line.long 0x0 "AS_CLRKEYLOW,Overlay Color Key Low" hexmask.long.tbyte 0x0 0.--23. 1. "PIXEL,Low range of RGB color key applied to AS buffer. Each overlay has an independent colorkey enable." group.long 0x190++0x3 line.long 0x0 "AS_CLRKEYHIGH,Overlay Color Key High" hexmask.long.tbyte 0x0 0.--23. 1. "PIXEL,High range of RGB color key applied to AS buffer. Each overlay has an independent colorkey enable." group.long 0x1A0++0x3 line.long 0x0 "CSC1_COEF0,Color Space Conversion Coefficient Register 0" bitfld.long 0x0 31. "YCBCR_MODE,Set to 1 when performing YCbCr conversion to RGB" "0: YUV to RGB,1: YCbCr to RGB" newline bitfld.long 0x0 30. "BYPASS,Bypass the CSC unit in the scaling engine" "0,1" newline hexmask.long.word 0x0 18.--28. 1. "C0,Two's compliment Y multiplier coefficient. YUV=0x100 (1.000) YCbCr=0x12A (1.164)" newline hexmask.long.word 0x0 9.--17. 1. "UV_OFFSET,Two's compliment phase offset implicit for CbCr data" newline hexmask.long.word 0x0 0.--8. 1. "Y_OFFSET,Two's compliment amplitude offset implicit in the Y data" group.long 0x1B0++0x3 line.long 0x0 "CSC1_COEF1,Color Space Conversion Coefficient Register 1" hexmask.long.word 0x0 16.--26. 1. "C1,Two's compliment Red V/Cr multiplier coefficient. YUV=0x123 (1.140) YCbCr=0x198 (1.596)" newline hexmask.long.word 0x0 0.--10. 1. "C4,Two's compliment Blue U/Cb multiplier coefficient. YUV=0x208 (2.032) YCbCr=0x204 (2.017)" group.long 0x1C0++0x3 line.long 0x0 "CSC1_COEF2,Color Space Conversion Coefficient Register 2" hexmask.long.word 0x0 16.--26. 1. "C2,Two's complement Green V/Cr multiplier coefficient. YUV=0x76B (-0.581) YCbCr=0x730 (-0.813)" newline hexmask.long.word 0x0 0.--10. 1. "C3,Two's complement Green U/Cb multiplier coefficient. YUV=0x79C (-0.394) YCbCr=0x79C (-0.392)" group.long 0x320++0x3 line.long 0x0 "POWER,PXP Power Control Register" bitfld.long 0x0 9.--11. "ROT_MEM_LP_STATE,Select the low power state of the Rotation (ROT) memory." "0: Memory is not in low power state.,1: Light Sleep Mode. Low leakage mode maintain..,2: Deep Sleep Mode. Low leakage mode maintain..,?,4: Shut Down Mode. Shut Down periphery and core no..,?,?,?" group.long 0x400++0x3 line.long 0x0 "NEXT,Next Frame Pointer" hexmask.long 0x0 2.--31. 1. "POINTER,A pointer to a data structure containing register values to be used when processing the next frame" newline rbitfld.long 0x0 0. "ENABLED,Indicates that the 'next frame' functionality has been enabled" "0,1" group.long 0x440++0x3 line.long 0x0 "PORTER_DUFF_CTRL,PXP Alpha Engine A Control Register." hexmask.long.byte 0x0 24.--31. 1. "S1_GLOBAL_ALPHA,s1 global alpha" newline hexmask.long.byte 0x0 16.--23. 1. "S0_GLOBAL_ALPHA,s0 global alpha" newline bitfld.long 0x0 13. "S1_COLOR_MODE,s1 color mode" "0: Original pixel,1: Scaled pixel" newline bitfld.long 0x0 12. "S1_ALPHA_MODE,s1 alpha mode (Porter-Duff Alpha mode)" "0: Straight mode,1: Inverted mode" newline bitfld.long 0x0 10.--11. "S1_GLOBAL_ALPHA_MODE,s1 global alpha mode (Porter-Duff Global Alpha mode)" "0: Global alpha,1: Local alpha,2: Scaled alpha,3: Scaled alpha" newline bitfld.long 0x0 8.--9. "S1_S0_FACTOR_MODE,s1 to s0 factor mode (Porter-Duff factor mode)" "0: 1,1: 0,2: Straight alpha,3: Inverse alpha" newline bitfld.long 0x0 6. "S0_COLOR_MODE,s0 color mode (Porter-Duff color mode)" "0: Original pixel,1: Scaled pixel" newline bitfld.long 0x0 5. "S0_ALPHA_MODE,s0 alpha mode (Porter-Duff alpha mode)" "0: Straight mode,1: Inverted mode" newline bitfld.long 0x0 3.--4. "S0_GLOBAL_ALPHA_MODE,s0 global alpha mode" "0: Global alpha,1: Local alpha,2: Scaled alpha,3: Scaled alpha" newline bitfld.long 0x0 1.--2. "S0_S1_FACTOR_MODE,s0 to s1 factor mode" "0: 1,1: 0,2: Straight alpha,3: Inverse alpha" newline bitfld.long 0x0 0. "PORTER_DUFF_ENABLE,Porter-Duff Enable" "0: Disabled,1: Enabled" tree.end endif tree "RDC" base ad:0x40C78000 rgroup.long 0x0++0x3 line.long 0x0 "VIR,Version Information" hexmask.long.byte 0x0 20.--27. 1. "NRGN,Number of Memory Regions" hexmask.long.byte 0x0 12.--19. 1. "NPER,Number of Peripherals" newline hexmask.long.byte 0x0 4.--11. 1. "NMSTR,Number of Masters" hexmask.long.byte 0x0 0.--3. 1. "NDID,Number of Domains" group.long 0x24++0xB line.long 0x0 "STAT,Status" bitfld.long 0x0 8. "PDS,Power Domain Status" "0: Power Down Domain is OFF,1: Power Down Domain is ON" hexmask.long.byte 0x0 0.--3. 1. "DID,Domain ID" line.long 0x4 "INTCTRL,Interrupt and Control" bitfld.long 0x4 0. "RCI_EN,Restoration Complete Interrupt" "0: Interrupt Disabled,1: Interrupt Enabled" line.long 0x8 "INTSTAT,Interrupt Status" eventfld.long 0x8 0. "INT,Interrupt Status" "0: No Interrupt Pending,1: Interrupt Pending" repeat 12. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x200)++0x3 line.long 0x0 "MDA$1,Master Domain Assignment" bitfld.long 0x0 31. "LCK,Assignment Lock" "0: Not Locked,1: Locked" bitfld.long 0x0 0.--1. "DID,Domain ID" "0: Master assigned to Processing Domain 0,1: Master assigned to Processing Domain 1,?,?" repeat.end repeat 128. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x400)++0x3 line.long 0x0 "PDAP$1,Peripheral Domain Access Permissions" bitfld.long 0x0 31. "LCK,Peripheral Permissions Lock" "0: Not Locked,1: Locked" bitfld.long 0x0 30. "SREQ,Semaphore Required" "0: Semaphores have no effect,1: Semaphores are enforced" newline bitfld.long 0x0 3. "D1R,Domain 1 Read Access" "0: No Read Access,1: Read Access Allowed" bitfld.long 0x0 2. "D1W,Domain 1 Write Access" "0: No Write Access,1: Write Access Allowed" newline bitfld.long 0x0 1. "D0R,Domain 0 Read Access" "0: No Read Access,1: Read Access Allowed" bitfld.long 0x0 0. "D0W,Domain 0 Write Access" "0: No Write Access,1: Write Access Allowed" repeat.end repeat 59. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x800)++0x3 line.long 0x0 "MRSA$1,Memory Region Start Address" hexmask.long 0x0 7.--31. 1. "SADR,Start address for memory region" repeat.end repeat 59. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x804)++0x3 line.long 0x0 "MREA$1,Memory Region End Address" hexmask.long 0x0 7.--31. 1. "EADR,Upper bound for memory region" repeat.end repeat 59. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x808)++0x3 line.long 0x0 "MRC$1,Memory Region Control" bitfld.long 0x0 31. "LCK,Region Lock" "0: No Lock. All fields in this register may be..,1: Locked. No fields in this register may be.." bitfld.long 0x0 30. "ENA,Region Enable" "0: Memory region is not defined or restricted.,1: Memory boundaries domain permissions and.." newline bitfld.long 0x0 3. "D1R,Domain 1 Read Access to Region" "0: Processing Domain 1 does not have Read access to..,1: Processing Domain 1 has Read access to the.." bitfld.long 0x0 2. "D1W,Domain 1 Write Access to Region" "0: Processing Domain 1 does not have Write access..,1: Processing Domain 1 has Write access to the.." newline bitfld.long 0x0 1. "D0R,Domain 0 Read Access to Region" "0: Processing Domain 0 does not have Read access to..,1: Processing Domain 0 has Read access to the.." bitfld.long 0x0 0. "D0W,Domain 0 Write Access to Region" "0: Processing Domain 0 does not have Write access..,1: Processing Domain 0 has Write access to the.." repeat.end repeat 59. (increment 0x0 0x1)(increment 0x0 0x10) group.long ($2+0x80C)++0x3 line.long 0x0 "MRVS$1,Memory Region Violation Status" hexmask.long 0x0 5.--31. 1. "VADR,Violating Address" eventfld.long 0x0 4. "AD,Access Denied" "0,1" newline rbitfld.long 0x0 0.--1. "VDID,Violating Domain ID" "0: Processing Domain 0,1: Processing Domain 1,?,?" repeat.end tree.end tree "RDC_SEMAPHORE" base ad:0x0 tree "RDC_SEMAPHORE1" base ad:0x40C44000 repeat 64. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2)++0x0 line.byte 0x0 "GATE$1,Gate Register" rbitfld.byte 0x0 4.--5. "LDOM,Read-only bits. They indicate which domain had currently locked the gate." "0: The gate is locked by domain 0. (True if the..,1: The gate has been locked by domain 1.,?,?" hexmask.byte 0x0 0.--3. 1. "GTFSM,Gate Finite State Machine." repeat.end group.word 0x42++0x1 line.word 0x0 "RSTGT_R,Reset Gate Read" hexmask.word.byte 0x0 8.--15. 1. "RSTGTN,Reset Gate Number" rbitfld.word 0x0 4.--5. "RSTGSM,Reset Gate Finite State Machine" "0: Idle waiting for the first data pattern write.,1: Waiting for the second data pattern write.,2: The 2-write sequence has completed. Generate the..,3: This state encoding is never used and therefore.." hexmask.word.byte 0x0 0.--3. 1. "RSTGMS,Reset Gate Bus Master" group.word 0x42++0x1 line.word 0x0 "RSTGT_W,Reset Gate Write" hexmask.word.byte 0x0 8.--15. 1. "RSTGTN,Reset Gate Number" hexmask.word.byte 0x0 0.--7. 1. "RSTGDP,Reset Gate Data Pattern" tree.end tree "RDC_SEMAPHORE2" base ad:0x40CCC000 repeat 64. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2)++0x0 line.byte 0x0 "GATE$1,Gate Register" rbitfld.byte 0x0 4.--5. "LDOM,Read-only bits. They indicate which domain had currently locked the gate." "0: The gate is locked by domain 0. (True if the..,1: The gate has been locked by domain 1.,?,?" hexmask.byte 0x0 0.--3. 1. "GTFSM,Gate Finite State Machine." repeat.end group.word 0x42++0x1 line.word 0x0 "RSTGT_R,Reset Gate Read" hexmask.word.byte 0x0 8.--15. 1. "RSTGTN,Reset Gate Number" rbitfld.word 0x0 4.--5. "RSTGSM,Reset Gate Finite State Machine" "0: Idle waiting for the first data pattern write.,1: Waiting for the second data pattern write.,2: The 2-write sequence has completed. Generate the..,3: This state encoding is never used and therefore.." hexmask.word.byte 0x0 0.--3. 1. "RSTGMS,Reset Gate Bus Master" group.word 0x42++0x1 line.word 0x0 "RSTGT_W,Reset Gate Write" hexmask.word.byte 0x0 8.--15. 1. "RSTGTN,Reset Gate Number" hexmask.word.byte 0x0 0.--7. 1. "RSTGDP,Reset Gate Data Pattern" tree.end tree.end tree "RTWDOG" base ad:0x0 tree "RTWDOG3" base ad:0x40038000 group.long 0x0++0xF line.long 0x0 "CS,Watchdog Control and Status Register" bitfld.long 0x0 15. "WIN,Watchdog Window" "0: Window mode disabled.,1: Window mode enabled." eventfld.long 0x0 14. "FLG,Watchdog Interrupt Flag" "0: No interrupt occurred.,1: An interrupt occurred." newline bitfld.long 0x0 13. "CMD32EN,Enables or disables WDOG support for 32-bit (otherwise 16-bit or 8-bit) refresh/unlock command write words" "0: Disables support for 32-bit refresh/unlock..,1: Enables support for 32-bit refresh/unlock.." bitfld.long 0x0 12. "PRES,Watchdog prescaler" "0: 256 prescaler disabled.,1: 256 prescaler enabled." newline rbitfld.long 0x0 11. "ULK,Unlock status" "0: WDOG is locked.,1: WDOG is unlocked." rbitfld.long 0x0 10. "RCS,Reconfiguration Success" "0: Reconfiguring WDOG.,1: Reconfiguration is successful." newline bitfld.long 0x0 8.--9. "CLK,Watchdog Clock" "0,1,2,3" bitfld.long 0x0 7. "EN,Watchdog Enable" "0: Watchdog disabled.,1: Watchdog enabled." newline bitfld.long 0x0 6. "INT,Watchdog Interrupt" "0: Watchdog interrupts are disabled. Watchdog..,1: Watchdog interrupts are enabled. Watchdog resets.." bitfld.long 0x0 5. "UPDATE,Allow updates" "0: Updates not allowed. After the initial..,1: Updates allowed. Software can modify the.." newline bitfld.long 0x0 3.--4. "TST,Watchdog Test" "0: Watchdog test mode disabled.,1: Watchdog user mode enabled. (Watchdog test mode..,2: Watchdog test mode enabled only the low byte is..,3: Watchdog test mode enabled only the high byte is.." bitfld.long 0x0 2. "DBG,Debug Enable" "0: Watchdog disabled in chip debug mode.,1: Watchdog enabled in chip debug mode." newline bitfld.long 0x0 1. "WAIT,Wait Enable" "0: Watchdog disabled in chip wait mode.,1: Watchdog enabled in chip wait mode." bitfld.long 0x0 0. "STOP,Stop Enable" "0: Watchdog disabled in chip stop mode.,1: Watchdog enabled in chip stop mode." line.long 0x4 "CNT,Watchdog Counter Register" hexmask.long.byte 0x4 8.--15. 1. "CNTHIGH,High byte of the Watchdog Counter" hexmask.long.byte 0x4 0.--7. 1. "CNTLOW,Low byte of the Watchdog Counter" line.long 0x8 "TOVAL,Watchdog Timeout Value Register" hexmask.long.byte 0x8 8.--15. 1. "TOVALHIGH,High byte of the timeout value" hexmask.long.byte 0x8 0.--7. 1. "TOVALLOW,Low byte of the timeout value" line.long 0xC "WIN,Watchdog Window Register" hexmask.long.byte 0xC 8.--15. 1. "WINHIGH,High byte of Watchdog Window" hexmask.long.byte 0xC 0.--7. 1. "WINLOW,Low byte of Watchdog Window" tree.end tree "RTWDOG4" base ad:0x40C10000 group.long 0x0++0xF line.long 0x0 "CS,Watchdog Control and Status Register" bitfld.long 0x0 15. "WIN,Watchdog Window" "0: Window mode disabled.,1: Window mode enabled." eventfld.long 0x0 14. "FLG,Watchdog Interrupt Flag" "0: No interrupt occurred.,1: An interrupt occurred." newline bitfld.long 0x0 13. "CMD32EN,Enables or disables WDOG support for 32-bit (otherwise 16-bit or 8-bit) refresh/unlock command write words" "0: Disables support for 32-bit refresh/unlock..,1: Enables support for 32-bit refresh/unlock.." bitfld.long 0x0 12. "PRES,Watchdog prescaler" "0: 256 prescaler disabled.,1: 256 prescaler enabled." newline rbitfld.long 0x0 11. "ULK,Unlock status" "0: WDOG is locked.,1: WDOG is unlocked." rbitfld.long 0x0 10. "RCS,Reconfiguration Success" "0: Reconfiguring WDOG.,1: Reconfiguration is successful." newline bitfld.long 0x0 8.--9. "CLK,Watchdog Clock" "0,1,2,3" bitfld.long 0x0 7. "EN,Watchdog Enable" "0: Watchdog disabled.,1: Watchdog enabled." newline bitfld.long 0x0 6. "INT,Watchdog Interrupt" "0: Watchdog interrupts are disabled. Watchdog..,1: Watchdog interrupts are enabled. Watchdog resets.." bitfld.long 0x0 5. "UPDATE,Allow updates" "0: Updates not allowed. After the initial..,1: Updates allowed. Software can modify the.." newline bitfld.long 0x0 3.--4. "TST,Watchdog Test" "0: Watchdog test mode disabled.,1: Watchdog user mode enabled. (Watchdog test mode..,2: Watchdog test mode enabled only the low byte is..,3: Watchdog test mode enabled only the high byte is.." bitfld.long 0x0 2. "DBG,Debug Enable" "0: Watchdog disabled in chip debug mode.,1: Watchdog enabled in chip debug mode." newline bitfld.long 0x0 1. "WAIT,Wait Enable" "0: Watchdog disabled in chip wait mode.,1: Watchdog enabled in chip wait mode." bitfld.long 0x0 0. "STOP,Stop Enable" "0: Watchdog disabled in chip stop mode.,1: Watchdog enabled in chip stop mode." line.long 0x4 "CNT,Watchdog Counter Register" hexmask.long.byte 0x4 8.--15. 1. "CNTHIGH,High byte of the Watchdog Counter" hexmask.long.byte 0x4 0.--7. 1. "CNTLOW,Low byte of the Watchdog Counter" line.long 0x8 "TOVAL,Watchdog Timeout Value Register" hexmask.long.byte 0x8 8.--15. 1. "TOVALHIGH,High byte of the timeout value" hexmask.long.byte 0x8 0.--7. 1. "TOVALLOW,Low byte of the timeout value" line.long 0xC "WIN,Watchdog Window Register" hexmask.long.byte 0xC 8.--15. 1. "WINHIGH,High byte of Watchdog Window" hexmask.long.byte 0xC 0.--7. 1. "WINLOW,Low byte of Watchdog Window" tree.end tree.end tree "SAI" base ad:0x0 tree "SAI1" base ad:0x40404000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--19. 1. "FRAME,Frame Size" hexmask.long.byte 0x4 8.--11. 1. "FIFO,FIFO Size" newline hexmask.long.byte 0x4 0.--3. 1. "DATALINE,Number of Datalines" group.long 0x8++0x17 line.long 0x0 "TCSR,Transmit Control" bitfld.long 0x0 31. "TE,Transmitter Enable" "0: Transmitter is disabled.,1: Transmitter is enabled or transmitter has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Transmitter disabled in Stop mode.,1: Transmitter enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Transmitter is disabled in Debug mode after..,1: Transmitter is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Transmit bit clock is disabled.,1: Transmit bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Transmit underrun not detected.,1: Transmit underrun detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled transmit FIFO is empty.,1: Enabled transmit FIFO is empty." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Transmit FIFO watermark has not been reached.,1: Transmit FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "TCR1,Transmit Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "TFW,Transmit FIFO Watermark" line.long 0x8 "TCR2,Transmit Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with receiver." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit clock is active high with drive outputs on..,1: Bit clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "TCR3,Transmit Configuration 3" hexmask.long.byte 0xC 24.--27. 1. "CFR,Channel FIFO Reset" hexmask.long.byte 0xC 16.--19. 1. "TCE,Transmit Channel Enable" newline hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "TCR4,Transmit Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 26.--27. "FCOMB,FIFO Combine Mode" "0: FIFO combine mode disabled.,1: FIFO combine mode enabled on FIFO reads (from..,2: FIFO combine mode enabled on FIFO writes (by..,3: FIFO combine mode enabled on FIFO reads (from.." newline bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled.,?,2: 8-bit FIFO packing is enabled.,3: 16-bit FIFO packing is enabled." hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame size" newline hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" bitfld.long 0x10 5. "CHMOD,Channel Mode" "0: TDM mode transmit data pins are tri-stated when..,1: Output mode transmit data pins are never.." newline bitfld.long 0x10 4. "MF,MSB First" "0: LSB is transmitted first.,1: MSB is transmitted first." bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." newline bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." newline bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame sync is generated externally in Slave mode.,1: Frame sync is generated internally in Master mode." line.long 0x14 "TCR5,Transmit Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x20)++0x3 line.long 0x0 "TDR[$1],Transmit Data" hexmask.long 0x0 0.--31. 1. "TDR,Transmit Data Register" repeat.end repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0x40)++0x3 line.long 0x0 "TFR[$1],Transmit FIFO" bitfld.long 0x0 31. "WCP,Write Channel Pointer" "0: No effect.,1: FIFO combine is enabled for FIFO writes and this.." hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" newline hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" repeat.end group.long 0x60++0x3 line.long 0x0 "TMR,Transmit Mask" hexmask.long 0x0 0.--31. 1. "TWM,Transmit Word Mask" group.long 0x88++0x17 line.long 0x0 "RCSR,Receive Control" bitfld.long 0x0 31. "RE,Receiver Enable" "0: Receiver is disabled.,1: Receiver is enabled or receiver has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Receiver disabled in Stop mode.,1: Receiver enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Receiver is disabled in Debug mode after..,1: Receiver is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Receive bit clock is disabled.,1: Receive bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Receive overflow not detected.,1: Receive overflow detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled receive FIFO is full.,1: Enabled receive FIFO is full." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Receive FIFO watermark not reached.,1: Receive FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "RCR1,Receive Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "RFW,Receive FIFO Watermark" line.long 0x8 "RCR2,Receive Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with transmitter." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit Clock is active high with drive outputs on..,1: Bit Clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "RCR3,Receive Configuration 3" hexmask.long.byte 0xC 24.--27. 1. "CFR,Channel FIFO Reset" hexmask.long.byte 0xC 16.--19. 1. "RCE,Receive Channel Enable" newline hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "RCR4,Receive Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 26.--27. "FCOMB,FIFO Combine Mode" "0: FIFO combine mode disabled.,1: FIFO combine mode enabled on FIFO writes (from..,2: FIFO combine mode enabled on FIFO reads (by..,3: FIFO combine mode enabled on FIFO writes (from.." newline bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled,?,2: 8-bit FIFO packing is enabled,3: 16-bit FIFO packing is enabled" hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame Size" newline hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" bitfld.long 0x10 4. "MF,MSB First" "0: LSB is received first.,1: MSB is received first." newline bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." newline bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame Sync is generated externally in Slave mode.,1: Frame Sync is generated internally in Master mode." line.long 0x14 "RCR5,Receive Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0xA0)++0x3 line.long 0x0 "RDR[$1],Receive Data" hexmask.long 0x0 0.--31. 1. "RDR,Receive Data Register" repeat.end repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2+0xC0)++0x3 line.long 0x0 "RFR[$1],Receive FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" bitfld.long 0x0 15. "RCP,Receive Channel Pointer" "0: No effect.,1: FIFO combine is enabled for FIFO reads and this.." newline hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" repeat.end group.long 0xE0++0x3 line.long 0x0 "RMR,Receive Mask" hexmask.long 0x0 0.--31. 1. "RWM,Receive Word Mask" tree.end tree "SAI2" base ad:0x40408000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--19. 1. "FRAME,Frame Size" hexmask.long.byte 0x4 8.--11. 1. "FIFO,FIFO Size" newline hexmask.long.byte 0x4 0.--3. 1. "DATALINE,Number of Datalines" group.long 0x8++0x1B line.long 0x0 "TCSR,Transmit Control" bitfld.long 0x0 31. "TE,Transmitter Enable" "0: Transmitter is disabled.,1: Transmitter is enabled or transmitter has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Transmitter disabled in Stop mode.,1: Transmitter enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Transmitter is disabled in Debug mode after..,1: Transmitter is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Transmit bit clock is disabled.,1: Transmit bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Transmit underrun not detected.,1: Transmit underrun detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled transmit FIFO is empty.,1: Enabled transmit FIFO is empty." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Transmit FIFO watermark has not been reached.,1: Transmit FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "TCR1,Transmit Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "TFW,Transmit FIFO Watermark" line.long 0x8 "TCR2,Transmit Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with receiver." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit clock is active high with drive outputs on..,1: Bit clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "TCR3,Transmit Configuration 3" bitfld.long 0xC 16. "TCE,Transmit Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "TCR4,Transmit Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled.,?,2: 8-bit FIFO packing is enabled.,3: 16-bit FIFO packing is enabled." newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 5. "CHMOD,Channel Mode" "0: TDM mode transmit data pins are tri-stated when..,1: Output mode transmit data pins are never.." bitfld.long 0x10 4. "MF,MSB First" "0: LSB is transmitted first.,1: MSB is transmitted first." newline bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." newline bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame sync is generated externally in Slave mode.,1: Frame sync is generated internally in Master mode." line.long 0x14 "TCR5,Transmit Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" line.long 0x18 "TDR0,Transmit Data" hexmask.long 0x18 0.--31. 1. "TDR,Transmit Data Register" rgroup.long 0x40++0x3 line.long 0x0 "TFR0,Transmit FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0x60++0x3 line.long 0x0 "TMR,Transmit Mask" hexmask.long 0x0 0.--31. 1. "TWM,Transmit Word Mask" group.long 0x88++0x17 line.long 0x0 "RCSR,Receive Control" bitfld.long 0x0 31. "RE,Receiver Enable" "0: Receiver is disabled.,1: Receiver is enabled or receiver has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Receiver disabled in Stop mode.,1: Receiver enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Receiver is disabled in Debug mode after..,1: Receiver is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Receive bit clock is disabled.,1: Receive bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Receive overflow not detected.,1: Receive overflow detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled receive FIFO is full.,1: Enabled receive FIFO is full." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Receive FIFO watermark not reached.,1: Receive FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "RCR1,Receive Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "RFW,Receive FIFO Watermark" line.long 0x8 "RCR2,Receive Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with transmitter." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit Clock is active high with drive outputs on..,1: Bit Clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "RCR3,Receive Configuration 3" bitfld.long 0xC 16. "RCE,Receive Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "RCR4,Receive Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled,?,2: 8-bit FIFO packing is enabled,3: 16-bit FIFO packing is enabled" newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame Size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 4. "MF,MSB First" "0: LSB is received first.,1: MSB is received first." bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." newline bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." newline bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame Sync is generated externally in Slave mode.,1: Frame Sync is generated internally in Master mode." line.long 0x14 "RCR5,Receive Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" rgroup.long 0xA0++0x3 line.long 0x0 "RDR0,Receive Data" hexmask.long 0x0 0.--31. 1. "RDR,Receive Data Register" rgroup.long 0xC0++0x3 line.long 0x0 "RFR0,Receive FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0xE0++0x3 line.long 0x0 "RMR,Receive Mask" hexmask.long 0x0 0.--31. 1. "RWM,Receive Word Mask" tree.end tree "SAI3" base ad:0x4040C000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--19. 1. "FRAME,Frame Size" hexmask.long.byte 0x4 8.--11. 1. "FIFO,FIFO Size" newline hexmask.long.byte 0x4 0.--3. 1. "DATALINE,Number of Datalines" group.long 0x8++0x1B line.long 0x0 "TCSR,Transmit Control" bitfld.long 0x0 31. "TE,Transmitter Enable" "0: Transmitter is disabled.,1: Transmitter is enabled or transmitter has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Transmitter disabled in Stop mode.,1: Transmitter enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Transmitter is disabled in Debug mode after..,1: Transmitter is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Transmit bit clock is disabled.,1: Transmit bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Transmit underrun not detected.,1: Transmit underrun detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled transmit FIFO is empty.,1: Enabled transmit FIFO is empty." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Transmit FIFO watermark has not been reached.,1: Transmit FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "TCR1,Transmit Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "TFW,Transmit FIFO Watermark" line.long 0x8 "TCR2,Transmit Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with receiver." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit clock is active high with drive outputs on..,1: Bit clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "TCR3,Transmit Configuration 3" bitfld.long 0xC 16. "TCE,Transmit Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "TCR4,Transmit Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled.,?,2: 8-bit FIFO packing is enabled.,3: 16-bit FIFO packing is enabled." newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 5. "CHMOD,Channel Mode" "0: TDM mode transmit data pins are tri-stated when..,1: Output mode transmit data pins are never.." bitfld.long 0x10 4. "MF,MSB First" "0: LSB is transmitted first.,1: MSB is transmitted first." newline bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." newline bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame sync is generated externally in Slave mode.,1: Frame sync is generated internally in Master mode." line.long 0x14 "TCR5,Transmit Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" line.long 0x18 "TDR0,Transmit Data" hexmask.long 0x18 0.--31. 1. "TDR,Transmit Data Register" rgroup.long 0x40++0x3 line.long 0x0 "TFR0,Transmit FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0x60++0x3 line.long 0x0 "TMR,Transmit Mask" hexmask.long 0x0 0.--31. 1. "TWM,Transmit Word Mask" group.long 0x88++0x17 line.long 0x0 "RCSR,Receive Control" bitfld.long 0x0 31. "RE,Receiver Enable" "0: Receiver is disabled.,1: Receiver is enabled or receiver has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Receiver disabled in Stop mode.,1: Receiver enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Receiver is disabled in Debug mode after..,1: Receiver is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Receive bit clock is disabled.,1: Receive bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Receive overflow not detected.,1: Receive overflow detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled receive FIFO is full.,1: Enabled receive FIFO is full." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Receive FIFO watermark not reached.,1: Receive FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "RCR1,Receive Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "RFW,Receive FIFO Watermark" line.long 0x8 "RCR2,Receive Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with transmitter." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit Clock is active high with drive outputs on..,1: Bit Clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "RCR3,Receive Configuration 3" bitfld.long 0xC 16. "RCE,Receive Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "RCR4,Receive Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled,?,2: 8-bit FIFO packing is enabled,3: 16-bit FIFO packing is enabled" newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame Size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 4. "MF,MSB First" "0: LSB is received first.,1: MSB is received first." bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." newline bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." newline bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame Sync is generated externally in Slave mode.,1: Frame Sync is generated internally in Master mode." line.long 0x14 "RCR5,Receive Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" rgroup.long 0xA0++0x3 line.long 0x0 "RDR0,Receive Data" hexmask.long 0x0 0.--31. 1. "RDR,Receive Data Register" rgroup.long 0xC0++0x3 line.long 0x0 "RFR0,Receive FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0xE0++0x3 line.long 0x0 "RMR,Receive Mask" hexmask.long 0x0 0.--31. 1. "RWM,Receive Word Mask" tree.end tree "SAI4" base ad:0x40C40000 rgroup.long 0x0++0x7 line.long 0x0 "VERID,Version ID" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,Major Version Number" hexmask.long.byte 0x0 16.--23. 1. "MINOR,Minor Version Number" newline hexmask.long.word 0x0 0.--15. 1. "FEATURE,Feature Specification Number" line.long 0x4 "PARAM,Parameter" hexmask.long.byte 0x4 16.--19. 1. "FRAME,Frame Size" hexmask.long.byte 0x4 8.--11. 1. "FIFO,FIFO Size" newline hexmask.long.byte 0x4 0.--3. 1. "DATALINE,Number of Datalines" group.long 0x8++0x1B line.long 0x0 "TCSR,Transmit Control" bitfld.long 0x0 31. "TE,Transmitter Enable" "0: Transmitter is disabled.,1: Transmitter is enabled or transmitter has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Transmitter disabled in Stop mode.,1: Transmitter enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Transmitter is disabled in Debug mode after..,1: Transmitter is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Transmit bit clock is disabled.,1: Transmit bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Transmit underrun not detected.,1: Transmit underrun detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled transmit FIFO is empty.,1: Enabled transmit FIFO is empty." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Transmit FIFO watermark has not been reached.,1: Transmit FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "TCR1,Transmit Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "TFW,Transmit FIFO Watermark" line.long 0x8 "TCR2,Transmit Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with receiver." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit clock is active high with drive outputs on..,1: Bit clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "TCR3,Transmit Configuration 3" bitfld.long 0xC 16. "TCE,Transmit Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "TCR4,Transmit Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled.,?,2: 8-bit FIFO packing is enabled.,3: 16-bit FIFO packing is enabled." newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 5. "CHMOD,Channel Mode" "0: TDM mode transmit data pins are tri-stated when..,1: Output mode transmit data pins are never.." bitfld.long 0x10 4. "MF,MSB First" "0: LSB is transmitted first.,1: MSB is transmitted first." newline bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." newline bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame sync is generated externally in Slave mode.,1: Frame sync is generated internally in Master mode." line.long 0x14 "TCR5,Transmit Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" line.long 0x18 "TDR0,Transmit Data" hexmask.long 0x18 0.--31. 1. "TDR,Transmit Data Register" rgroup.long 0x40++0x3 line.long 0x0 "TFR0,Transmit FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0x60++0x3 line.long 0x0 "TMR,Transmit Mask" hexmask.long 0x0 0.--31. 1. "TWM,Transmit Word Mask" group.long 0x88++0x17 line.long 0x0 "RCSR,Receive Control" bitfld.long 0x0 31. "RE,Receiver Enable" "0: Receiver is disabled.,1: Receiver is enabled or receiver has been.." bitfld.long 0x0 30. "STOPE,Stop Enable" "0: Receiver disabled in Stop mode.,1: Receiver enabled in Stop mode." newline bitfld.long 0x0 29. "DBGE,Debug Enable" "0: Receiver is disabled in Debug mode after..,1: Receiver is enabled in Debug mode." bitfld.long 0x0 28. "BCE,Bit Clock Enable" "0: Receive bit clock is disabled.,1: Receive bit clock is enabled." newline bitfld.long 0x0 25. "FR,FIFO Reset" "0: No effect.,1: FIFO reset." bitfld.long 0x0 24. "SR,Software Reset" "0: No effect.,1: Software reset." newline eventfld.long 0x0 20. "WSF,Word Start Flag" "0: Start of word not detected.,1: Start of word detected." eventfld.long 0x0 19. "SEF,Sync Error Flag" "0: Sync error not detected.,1: Frame sync error detected." newline eventfld.long 0x0 18. "FEF,FIFO Error Flag" "0: Receive overflow not detected.,1: Receive overflow detected." rbitfld.long 0x0 17. "FWF,FIFO Warning Flag" "0: No enabled receive FIFO is full.,1: Enabled receive FIFO is full." newline rbitfld.long 0x0 16. "FRF,FIFO Request Flag" "0: Receive FIFO watermark not reached.,1: Receive FIFO watermark has been reached." bitfld.long 0x0 12. "WSIE,Word Start Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." newline bitfld.long 0x0 11. "SEIE,Sync Error Interrupt Enable" "0: Disables interrupt.,1: Enables interrupt." bitfld.long 0x0 10. "FEIE,FIFO Error Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 9. "FWIE,FIFO Warning Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." bitfld.long 0x0 8. "FRIE,FIFO Request Interrupt Enable" "0: Disables the interrupt.,1: Enables the interrupt." newline bitfld.long 0x0 1. "FWDE,FIFO Warning DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." bitfld.long 0x0 0. "FRDE,FIFO Request DMA Enable" "0: Disables the DMA request.,1: Enables the DMA request." line.long 0x4 "RCR1,Receive Configuration 1" hexmask.long.byte 0x4 0.--4. 1. "RFW,Receive FIFO Watermark" line.long 0x8 "RCR2,Receive Configuration 2" bitfld.long 0x8 30. "SYNC,Synchronous Mode" "0: Asynchronous mode.,1: Synchronous with transmitter." bitfld.long 0x8 29. "BCS,Bit Clock Swap" "0: Use the normal bit clock source.,1: Swap the bit clock source." newline bitfld.long 0x8 28. "BCI,Bit Clock Input" "0: No effect.,1: Internal logic is clocked as if bit clock was.." bitfld.long 0x8 26.--27. "MSEL,MCLK Select" "0: Bus Clock selected.,1: Master Clock (MCLK) 1 option selected.,2: Master Clock (MCLK) 2 option selected.,3: Master Clock (MCLK) 3 option selected." newline bitfld.long 0x8 25. "BCP,Bit Clock Polarity" "0: Bit Clock is active high with drive outputs on..,1: Bit Clock is active low with drive outputs on.." bitfld.long 0x8 24. "BCD,Bit Clock Direction" "0: Bit clock is generated externally in Slave mode.,1: Bit clock is generated internally in Master mode." newline bitfld.long 0x8 23. "BYP,Bit Clock Bypass" "0: Internal bit clock is generated from bit clock..,1: Internal bit clock is divide by one of the audio.." hexmask.long.byte 0x8 0.--7. 1. "DIV,Bit Clock Divide" line.long 0xC "RCR3,Receive Configuration 3" bitfld.long 0xC 16. "RCE,Receive Channel Enable" "0,1" hexmask.long.byte 0xC 0.--4. 1. "WDFL,Word Flag Configuration" line.long 0x10 "RCR4,Receive Configuration 4" bitfld.long 0x10 28. "FCONT,FIFO Continue on Error" "0: On FIFO error the SAI will continue from the..,1: On FIFO error the SAI will continue from the.." bitfld.long 0x10 24.--25. "FPACK,FIFO Packing Mode" "0: FIFO packing is disabled,?,2: 8-bit FIFO packing is enabled,3: 16-bit FIFO packing is enabled" newline hexmask.long.byte 0x10 16.--20. 1. "FRSZ,Frame Size" hexmask.long.byte 0x10 8.--12. 1. "SYWD,Sync Width" newline bitfld.long 0x10 4. "MF,MSB First" "0: LSB is received first.,1: MSB is received first." bitfld.long 0x10 3. "FSE,Frame Sync Early" "0: Frame sync asserts with the first bit of the..,1: Frame sync asserts one bit before the first bit.." newline bitfld.long 0x10 2. "ONDEM,On Demand Mode" "0: Internal frame sync is generated continuously.,1: Internal frame sync is generated when the FIFO.." bitfld.long 0x10 1. "FSP,Frame Sync Polarity" "0: Frame sync is active high.,1: Frame sync is active low." newline bitfld.long 0x10 0. "FSD,Frame Sync Direction" "0: Frame Sync is generated externally in Slave mode.,1: Frame Sync is generated internally in Master mode." line.long 0x14 "RCR5,Receive Configuration 5" hexmask.long.byte 0x14 24.--28. 1. "WNW,Word N Width" hexmask.long.byte 0x14 16.--20. 1. "W0W,Word 0 Width" newline hexmask.long.byte 0x14 8.--12. 1. "FBT,First Bit Shifted" rgroup.long 0xA0++0x3 line.long 0x0 "RDR0,Receive Data" hexmask.long 0x0 0.--31. 1. "RDR,Receive Data Register" rgroup.long 0xC0++0x3 line.long 0x0 "RFR0,Receive FIFO" hexmask.long.byte 0x0 16.--21. 1. "WFP,Write FIFO Pointer" hexmask.long.byte 0x0 0.--5. 1. "RFP,Read FIFO Pointer" group.long 0xE0++0x3 line.long 0x0 "RMR,Receive Mask" hexmask.long 0x0 0.--31. 1. "RWM,Receive Word Mask" tree.end tree.end tree "SEMA4" base ad:0x40CC8000 repeat 16. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2)++0x0 line.byte 0x0 "Gate$1,Semaphores Gate n Register" bitfld.byte 0x0 0.--1. "GTFSM,Gate Finite State Machine." "0: The gate is unlocked (free).,1: The gate has been locked by processor 0.,2: The gate has been locked by processor 1.,3: This state encoding is never used and therefore.." repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x8) group.word ($2+0x40)++0x1 line.word 0x0 "CP$1INE,Semaphores Processor n IRQ Notification Enable" bitfld.word 0x0 15. "INE8,Interrupt Request Notification Enable 8. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 8." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 14. "INE9,Interrupt Request Notification Enable 9. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 9." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 13. "INE10,Interrupt Request Notification Enable 10. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 10." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 12. "INE11,Interrupt Request Notification Enable 11. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 11." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 11. "INE12,Interrupt Request Notification Enable 12. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 12." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 10. "INE13,Interrupt Request Notification Enable 13. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 13." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 9. "INE14,Interrupt Request Notification Enable 14. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 14." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 8. "INE15,Interrupt Request Notification Enable 15. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 15." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 7. "INE0,Interrupt Request Notification Enable 0" "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 6. "INE1,Interrupt Request Notification Enable 1" "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 5. "INE2,Interrupt Request Notification Enable 2" "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 4. "INE3,Interrupt Request Notification Enable 3" "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 3. "INE4,Interrupt Request Notification Enable 4. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 4." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 2. "INE5,Interrupt Request Notification Enable 5. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 5." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." newline bitfld.word 0x0 1. "INE6,Interrupt Request Notification Enable 6. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 6." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." bitfld.word 0x0 0. "INE7,Interrupt Request Notification Enable 7. This field is a bitmap to enable the generation of an interrupt notification from a failed attempt to lock gate 7." "0: The generation of the notification interrupt is..,1: The generation of the notification interrupt is.." repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x8) rgroup.word ($2+0x80)++0x1 line.word 0x0 "CP$1NTF,Semaphores Processor n IRQ Notification" bitfld.word 0x0 15. "GN8,Gate 8 Notification" "0,1" bitfld.word 0x0 14. "GN9,Gate 9 Notification" "0,1" newline bitfld.word 0x0 13. "GN10,Gate 10 Notification" "0,1" bitfld.word 0x0 12. "GN11,Gate 11 Notification" "0,1" newline bitfld.word 0x0 11. "GN12,Gate 12 Notification" "0,1" bitfld.word 0x0 10. "GN13,Gate 13 Notification" "0,1" newline bitfld.word 0x0 9. "GN14,Gate 14 Notification" "0,1" bitfld.word 0x0 8. "GN15,Gate 15 Notification" "0,1" newline bitfld.word 0x0 7. "GN0,Gate 0 Notification" "0,1" bitfld.word 0x0 6. "GN1,Gate 1 Notification" "0,1" newline bitfld.word 0x0 5. "GN2,Gate 2 Notification" "0,1" bitfld.word 0x0 4. "GN3,Gate 3 Notification" "0,1" newline bitfld.word 0x0 3. "GN4,Gate 4 Notification" "0,1" bitfld.word 0x0 2. "GN5,Gate 5 Notification" "0,1" newline bitfld.word 0x0 1. "GN6,Gate 6 Notification" "0,1" bitfld.word 0x0 0. "GN7,Gate 7 Notification" "0,1" repeat.end group.word 0x100++0x1 line.word 0x0 "RSTGT,Semaphores (Secure) Reset Gate n" hexmask.word.byte 0x0 8.--15. 1. "RSTGTN,Reset Gate Number" hexmask.word.byte 0x0 0.--7. 1. "RSTGSM_RSTGMS_RSTGDP,This field contains sub-fields that vary depending on whether it is being read or written" group.word 0x104++0x1 line.word 0x0 "RSTNTF,Semaphores (Secure) Reset IRQ Notification" hexmask.word.byte 0x0 8.--15. 1. "RSTNTN,Reset Notification Number" hexmask.word.byte 0x0 0.--7. 1. "RSTNSM_RSTNMS_RSTNDP,This field contains sub-fields that vary depending on whether it is being read or written" tree.end tree "SEMC" base ad:0x400D4000 group.long 0x0++0xF line.long 0x0 "MCR,Module Control Register" hexmask.long.byte 0x0 24.--28. 1. "BTO,Bus timeout cycles" hexmask.long.byte 0x0 16.--23. 1. "CTO,Command Execution timeout cycles" newline bitfld.long 0x0 7. "WPOL1,R/B# polarity for NAND device" "0: R/B# polarity is not changed.,1: R/B# polarity is inverted." bitfld.long 0x0 6. "WPOL0,WAIT/RDY polarity for SRAM/NOR" "0: WAIT/RDY polarity is not changed.,1: WAIT/RDY polarity is inverted." newline bitfld.long 0x0 2. "DQSMD,DQS (read strobe) mode" "0: Dummy read strobe loopbacked internally,1: Dummy read strobe loopbacked from DQS pad" bitfld.long 0x0 1. "MDIS,Module Disable" "0: Module enabled,1: Module disabled" newline bitfld.long 0x0 0. "SWRST,Software Reset" "0: No reset,1: Reset" line.long 0x4 "IOCR,IO MUX Control Register" bitfld.long 0x4 29. "CLKX1_AO,SEMC_CLKX1 Always On" "0: SEMC_CLKX1 is controlled by MUX_CLKX1,1: SEMC_CLKX1 is always on" bitfld.long 0x4 28. "CLKX0_AO,SEMC_CLKX0 Always On" "0: SEMC_CLKX0 is controlled by MUX_CLKX0,1: SEMC_CLKX0 is always on" newline bitfld.long 0x4 26.--27. "MUX_CLKX1,SEMC_CLKX1 function selection" "0: Keep low,1: NOR clock,2: SRAM clock,3: NOR and SRAM clock suitable for Multi-Chip.." bitfld.long 0x4 24.--25. "MUX_CLKX0,SEMC_CLKX0 function selection" "0: Keep low,1: NOR clock,2: SRAM clock,3: NOR and SRAM clock suitable for Multi-Chip.." newline hexmask.long.byte 0x4 20.--23. 1. "MUX_RDY,SEMC_RDY function selection" hexmask.long.byte 0x4 16.--19. 1. "MUX_CSX3,SEMC_CSX3 output selection" newline hexmask.long.byte 0x4 12.--15. 1. "MUX_CSX2,SEMC_CSX2 output selection" hexmask.long.byte 0x4 8.--11. 1. "MUX_CSX1,SEMC_CSX1 output selection" newline hexmask.long.byte 0x4 4.--7. 1. "MUX_CSX0,SEMC_CSX0 output selection" hexmask.long.byte 0x4 0.--3. 1. "MUX_A8,SEMC_ADDR08 output selection" line.long 0x8 "BMCR0,Bus (AXI) Master Control Register 0" hexmask.long.byte 0x8 16.--23. 1. "WRWS,Weight of slave hit with Read/Write Switch" hexmask.long.byte 0x8 8.--15. 1. "WSH,Weight of Slave Hit without read/write switch" newline hexmask.long.byte 0x8 4.--7. 1. "WAGE,Weight of AGE" hexmask.long.byte 0x8 0.--3. 1. "WQOS,Weight of QOS" line.long 0xC "BMCR1,Bus (AXI) Master Control Register 1" hexmask.long.byte 0xC 24.--31. 1. "WBR,Weight of Bank Rotation" hexmask.long.byte 0xC 16.--23. 1. "WRWS,Weight of slave hit without Read/Write Switch" newline hexmask.long.byte 0xC 8.--15. 1. "WPH,Weight of Page Hit" hexmask.long.byte 0xC 4.--7. 1. "WAGE,Weight of AGE" newline hexmask.long.byte 0xC 0.--3. 1. "WQOS,Weight of QOS" repeat 9. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x10)++0x3 line.long 0x0 "BR[$1],Base Register n" hexmask.long.tbyte 0x0 12.--31. 1. "BA,Base Address" hexmask.long.byte 0x0 1.--5. 1. "MS,Memory size" newline bitfld.long 0x0 0. "VLD,Valid" "0: The memory is invalid can not be accessed.,1: The memory is valid can be accessed." repeat.end group.long 0x34++0x57 line.long 0x0 "DLLCR,DLL Control Register" hexmask.long.byte 0x0 9.--14. 1. "OVRDVAL,Override Value" bitfld.long 0x0 8. "OVRDEN,Override Enable" "0: The delay cell number is not overridden.,1: The delay cell number is overridden." newline hexmask.long.byte 0x0 3.--6. 1. "SLVDLYTARGET,Delay Target for Slave" bitfld.long 0x0 1. "DLLRESET,DLL Reset" "0: DLL is not reset.,1: DLL is reset." newline bitfld.long 0x0 0. "DLLEN,DLL calibration enable" "0: DLL calibration is disabled.,1: DLL calibration is enabled." line.long 0x4 "INTEN,Interrupt Enable Register" bitfld.long 0x4 5. "NDNOPENDEN,NAND no pending AXI access interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x4 4. "NDPAGEENDEN,NAND page end interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline bitfld.long 0x4 3. "AXIBUSERREN,AXI bus error interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x4 2. "AXICMDERREN,AXI command error interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline bitfld.long 0x4 1. "IPCMDERREN,IP command error interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x4 0. "IPCMDDONEEN,IP command done interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" line.long 0x8 "INTR,Interrupt Register" eventfld.long 0x8 5. "NDNOPEND,NAND no pending AXI write transaction interrupt" "0: At least one NAND AXI write transaction is..,1: All NAND AXI write pending transactions are.." eventfld.long 0x8 4. "NDPAGEEND,NAND page end interrupt" "0: The last address of main space in the NAND is..,1: The last address of main space in the NAND is.." newline eventfld.long 0x8 3. "AXIBUSERR,AXI bus error interrupt" "0: No AXI bus error.,1: AXI bus error occurs." eventfld.long 0x8 2. "AXICMDERR,AXI command error interrupt" "0: No AXI command error.,1: AXI command error occurs." newline eventfld.long 0x8 1. "IPCMDERR,IP command error done interrupt" "0: No IP command error.,1: IP command error occurs." eventfld.long 0x8 0. "IPCMDDONE,IP command normal done interrupt" "0: IP command is not done.,1: IP command is done." line.long 0xC "SDRAMCR0,SDRAM Control Register 0" bitfld.long 0xC 14. "BANK2,2 Bank selection bit" "0: SDRAM device has 4 banks.,1: SDRAM device has 2 banks." bitfld.long 0xC 10.--11. "CL,CAS Latency" "0: 1,1: 1,2: 2,3: 3" newline bitfld.long 0xC 8.--9. "COL,Column address bit number" "0: 12,1: 11,2: 10,3: 9" bitfld.long 0xC 7. "COL8,Column 8 selection" "0: Column address bit number is decided by COL field.,1: Column address bit number is 8. COL field is.." newline bitfld.long 0xC 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 8,5: 8,6: 8,7: 8" bitfld.long 0xC 0.--1. "PS,Port Size" "0: 8bit,1: 16bit,2: 32bit,?" line.long 0x10 "SDRAMCR1,SDRAM Control Register 1" hexmask.long.byte 0x10 20.--23. 1. "ACT2PRE,ACTIVE to PRECHARGE minimum time" hexmask.long.byte 0x10 16.--19. 1. "CKEOFF,CKE off minimum time" newline bitfld.long 0x10 13.--15. "WRC,WRITE recovery time" "0,1,2,3,4,5,6,7" hexmask.long.byte 0x10 8.--12. 1. "RFRC,REFRESH recovery time" newline hexmask.long.byte 0x10 4.--7. 1. "ACT2RW,ACTIVE to READ/WRITE delay" hexmask.long.byte 0x10 0.--3. 1. "PRE2ACT,PRECHARGE to ACTIVE/REFRESH command wait time" line.long 0x14 "SDRAMCR2,SDRAM Control Register 2" hexmask.long.byte 0x14 24.--31. 1. "ITO,SDRAM idle timeout" hexmask.long.byte 0x14 16.--23. 1. "ACT2ACT,ACTIVE to ACTIVE delay" newline hexmask.long.byte 0x14 8.--15. 1. "REF2REF,REFRESH to REFRESH delay" hexmask.long.byte 0x14 0.--7. 1. "SRRC,SELF REFRESH recovery time" line.long 0x18 "SDRAMCR3,SDRAM Control Register 3" hexmask.long.byte 0x18 24.--31. 1. "UT,Urgent refresh threshold" hexmask.long.byte 0x18 16.--23. 1. "RT,Refresh timer period" newline hexmask.long.byte 0x18 8.--15. 1. "PRESCALE,Prescaler period" bitfld.long 0x18 1.--3. "REBL,Refresh burst length" "0: 1,1: 2,2: 3,3: 4,4: 5,5: 6,6: 7,7: 8" newline bitfld.long 0x18 0. "REN,Refresh enable" "0: The SEMC does not send AUTO REFRESH command..,1: The SEMC sends AUTO REFRESH command automatically" line.long 0x1C "NANDCR0,NAND Control Register 0" bitfld.long 0x1C 8.--10. "COL,Column address bit number" "0: 16,1: 15,2: 14,3: 13,4: 12,5: 11,6: 10,7: 9" bitfld.long 0x1C 7. "EDO,EDO mode enabled" "0: EDO mode disabled,1: EDO mode enabled" newline bitfld.long 0x1C 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 16,5: 32,6: 64,7: 64" bitfld.long 0x1C 1. "SYNCEN,Synchronous Mode Enable" "0: Asynchronous mode is enabled.,1: Synchronous mode is enabled." newline bitfld.long 0x1C 0. "PS,Port Size" "0: 8bit,1: 16bit" line.long 0x20 "NANDCR1,NAND Control Register 1" hexmask.long.byte 0x20 28.--31. 1. "CEITV,CE# interval time" hexmask.long.byte 0x20 24.--27. 1. "TA,Turnaround time" newline hexmask.long.byte 0x20 20.--23. 1. "REH,RE# high time" hexmask.long.byte 0x20 16.--19. 1. "REL,RE# low time" newline hexmask.long.byte 0x20 12.--15. 1. "WEH,WE# high time" hexmask.long.byte 0x20 8.--11. 1. "WEL,WE# low time" newline hexmask.long.byte 0x20 4.--7. 1. "CEH,CE# hold time" hexmask.long.byte 0x20 0.--3. 1. "CES,CE# setup time" line.long 0x24 "NANDCR2,NAND Control Register 2" hexmask.long.byte 0x24 24.--29. 1. "TWB,WE# high to busy time" hexmask.long.byte 0x24 18.--23. 1. "TRR,Ready to RE# low time" newline hexmask.long.byte 0x24 12.--17. 1. "TADL,Address cycle to data loading time" hexmask.long.byte 0x24 6.--11. 1. "TRHW,RE# high to WE# low time" newline hexmask.long.byte 0x24 0.--5. 1. "TWHR,WE# high to RE# low time" line.long 0x28 "NANDCR3,NAND Control Register 3" hexmask.long.byte 0x28 28.--31. 1. "WDH,Write Data Hold time" hexmask.long.byte 0x28 24.--27. 1. "WDS,Write Data Setup time" newline hexmask.long.byte 0x28 20.--23. 1. "RDH,Read Data Hold time" hexmask.long.byte 0x28 16.--19. 1. "RDS,Read Data Setup time" newline bitfld.long 0x28 3. "CLE,NAND CLE Option" "0,1" bitfld.long 0x28 2. "NDOPT3,NAND option bit 3" "0,1" newline bitfld.long 0x28 1. "NDOPT2,NAND option bit 2" "0,1" bitfld.long 0x28 0. "NDOPT1,NAND option bit 1" "0,1" line.long 0x2C "NORCR0,NOR Control Register 0" hexmask.long.byte 0x2C 12.--15. 1. "COL,Column Address bit width" bitfld.long 0x2C 11. "ADVH,ADV# level control during address hold state" "0: ADV# is high during address hold state.,1: ADV# is low during address hold state." newline bitfld.long 0x2C 10. "ADVP,ADV# Polarity" "0: ADV# is active low.,1: ADV# is active high." bitfld.long 0x2C 8.--9. "AM,Address Mode" "0: Address/Data MUX mode (ADMUX),1: Advanced Address/Data MUX mode (AADM),2: Address/Data non-MUX mode (Non-ADMUX),3: Address/Data non-MUX mode (Non-ADMUX)" newline bitfld.long 0x2C 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 16,5: 32,6: 64,7: 64" bitfld.long 0x2C 1. "SYNCEN,Synchronous Mode Enable" "0: Asynchronous mode is enabled.,1: Synchronous mode is enabled. Only fixed latency.." newline bitfld.long 0x2C 0. "PS,Port Size" "0: 8bit,1: 16bit" line.long 0x30 "NORCR1,NOR Control Register 1" hexmask.long.byte 0x30 28.--31. 1. "REH,RE high time" hexmask.long.byte 0x30 24.--27. 1. "REL,RE low time" newline hexmask.long.byte 0x30 20.--23. 1. "WEH,WE high time" hexmask.long.byte 0x30 16.--19. 1. "WEL,WE low time" newline hexmask.long.byte 0x30 12.--15. 1. "AH,Address hold time" hexmask.long.byte 0x30 8.--11. 1. "AS,Address setup time" newline hexmask.long.byte 0x30 4.--7. 1. "CEH,CE hold time" hexmask.long.byte 0x30 0.--3. 1. "CES,CE setup time" line.long 0x34 "NORCR2,NOR Control Register 2" hexmask.long.byte 0x34 28.--31. 1. "RDH,Read hold time" hexmask.long.byte 0x34 24.--27. 1. "CEITV,CE# interval time" newline hexmask.long.byte 0x34 20.--23. 1. "RD,Read time" hexmask.long.byte 0x34 16.--19. 1. "LC,Latency count" newline hexmask.long.byte 0x34 12.--15. 1. "AWDH,Address to write data hold time" hexmask.long.byte 0x34 8.--11. 1. "TA,Turnaround time" line.long 0x38 "NORCR3,NOR Control Register 3" hexmask.long.byte 0x38 4.--7. 1. "AHSR,Address hold time for SYNC read" hexmask.long.byte 0x38 0.--3. 1. "ASSR,Address setup time for SYNC read" line.long 0x3C "SRAMCR0,SRAM Control Register 0" hexmask.long.byte 0x3C 12.--15. 1. "COL,Column Address bit width" bitfld.long 0x3C 11. "ADVH,ADV# level control during address hold state" "0: ADV# is high during address hold state.,1: ADV# is low during address hold state." newline bitfld.long 0x3C 10. "ADVP,ADV# polarity" "0: ADV# is active low.,1: ADV# is active high." bitfld.long 0x3C 8.--9. "AM,Address Mode" "0: Address/Data MUX mode (ADMUX),1: Advanced Address/Data MUX mode (AADM),2: Address/Data non-MUX mode (Non-ADMUX),3: Address/Data non-MUX mode (Non-ADMUX)" newline bitfld.long 0x3C 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 16,5: 32,6: 64,7: 64" bitfld.long 0x3C 3. "WAITSP,Wait Sample" "0: Wait pin is directly used by the SEMC.,1: Wait pin is sampled by internal clock before it.." newline bitfld.long 0x3C 2. "WAITEN,Wait Enable" "0: The SEMC does not monitor wait pin.,1: The SEMC monitors wait pin. The SEMC does not.." bitfld.long 0x3C 1. "SYNCEN,Synchronous Mode Enable" "0: Asynchronous mode is enabled.,1: Synchronous mode is enabled. Only fixed latency.." newline bitfld.long 0x3C 0. "PS,Port Size" "0: 8bit,1: 16bit" line.long 0x40 "SRAMCR1,SRAM Control Register 1" hexmask.long.byte 0x40 28.--31. 1. "REH,RE high time" hexmask.long.byte 0x40 24.--27. 1. "REL,RE low time" newline hexmask.long.byte 0x40 20.--23. 1. "WEH,WE high time" hexmask.long.byte 0x40 16.--19. 1. "WEL,WE low time" newline hexmask.long.byte 0x40 12.--15. 1. "AH,Address hold time" hexmask.long.byte 0x40 8.--11. 1. "AS,Address setup time" newline hexmask.long.byte 0x40 4.--7. 1. "CEH,CE hold time" hexmask.long.byte 0x40 0.--3. 1. "CES,CE setup time" line.long 0x44 "SRAMCR2,SRAM Control Register 2" hexmask.long.byte 0x44 28.--31. 1. "RDH,Read hold time" hexmask.long.byte 0x44 24.--27. 1. "CEITV,CE# interval time" newline hexmask.long.byte 0x44 20.--23. 1. "RD,Read time" hexmask.long.byte 0x44 16.--19. 1. "LC,Latency count" newline hexmask.long.byte 0x44 12.--15. 1. "AWDH,Address to write data hold time" hexmask.long.byte 0x44 8.--11. 1. "TA,Turnaround time" newline hexmask.long.byte 0x44 4.--7. 1. "WDH,Write Data hold time" hexmask.long.byte 0x44 0.--3. 1. "WDS,Write Data setup time" line.long 0x48 "SRAMCR3,SRAM Control Register 3" line.long 0x4C "DBICR0,DBI-B Control Register 0" hexmask.long.byte 0x4C 12.--15. 1. "COL,Column Address bit width" bitfld.long 0x4C 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 16,5: 32,6: 64,7: 64" newline bitfld.long 0x4C 0. "PS,Port Size" "0: 8bit,1: 16bit" line.long 0x50 "DBICR1,DBI-B Control Register 1" hexmask.long.byte 0x50 24.--30. 1. "REH,RDX High Time" hexmask.long.byte 0x50 16.--22. 1. "REL,RDX Low Time" newline hexmask.long.byte 0x50 12.--15. 1. "WEH,WRX High Time" hexmask.long.byte 0x50 8.--11. 1. "WEL,WRX Low Time" newline hexmask.long.byte 0x50 4.--7. 1. "CEH,CSX Hold Time" hexmask.long.byte 0x50 0.--3. 1. "CES,CSX Setup Time" line.long 0x54 "DBICR2,DBI-B Control Register 2" hexmask.long.byte 0x54 0.--3. 1. "CEITV,CSX interval time" group.long 0x90++0x13 line.long 0x0 "IPCR0,IP Command Control Register 0" hexmask.long 0x0 0.--31. 1. "SA,Slave address" line.long 0x4 "IPCR1,IP Command Control Register 1" hexmask.long.byte 0x4 8.--15. 1. "NAND_EXT_ADDR,NAND Extended Address" bitfld.long 0x4 0.--2. "DATSZ,Data Size in Byte" "0: 4,1: 1,2: 2,3: 3,4: 4,5: 4,6: 4,7: 4" line.long 0x8 "IPCR2,IP Command Control Register 2" bitfld.long 0x8 3. "BM3,Byte Mask for Byte 3 (IPTXDAT bit 31:24)" "0: Byte is unmasked,1: Byte is masked" bitfld.long 0x8 2. "BM2,Byte Mask for Byte 2 (IPTXDAT bit 23:16)" "0: Byte is unmasked,1: Byte is masked" newline bitfld.long 0x8 1. "BM1,Byte Mask for Byte 1 (IPTXDAT bit 15:8)" "0: Byte is unmasked,1: Byte is masked" bitfld.long 0x8 0. "BM0,Byte Mask for Byte 0 (IPTXDAT bit 7:0)" "0: Byte is unmasked,1: Byte is masked" line.long 0xC "IPCMD,IP Command Register" hexmask.long.word 0xC 16.--31. 1. "KEY,This field should be written with 0xA55A when trigging an IP command for all device types" hexmask.long.word 0xC 0.--15. 1. "CMD,SDRAM Commands: 0x8: Read 0x9: Write 0xA: Mode Register Set 0xB: Active 0xC: Auto Refresh 0xD: Self Refresh 0xE: Precharge 0xF: Precharge All Others: Reserved Self Refresh is sent to all SDRAM devices because they share the same SEMC_CLK pin" line.long 0x10 "IPTXDAT,TX DATA Register" hexmask.long 0x10 0.--31. 1. "DAT,Data value to use for an IP write command" rgroup.long 0xB0++0x3 line.long 0x0 "IPRXDAT,RX DATA Register" hexmask.long 0x0 0.--31. 1. "DAT,Data returned by device for an IP read command." rgroup.long 0xC0++0x3F line.long 0x0 "STS0,Status Register 0" bitfld.long 0x0 1. "NARDY,Indicating NAND device Ready/WAIT# pin level." "0: NAND device is not ready,1: NAND device is ready" bitfld.long 0x0 0. "IDLE,Indicating whether the SEMC is in idle state." "0,1" line.long 0x4 "STS1,Status Register 1" line.long 0x8 "STS2,Status Register 2" bitfld.long 0x8 3. "NDWRPEND,This field indicating whether there is pending AXI command (write) to NAND device." "0: No pending,1: Pending" line.long 0xC "STS3,Status Register 3" line.long 0x10 "STS4,Status Register 4" line.long 0x14 "STS5,Status Register 5" line.long 0x18 "STS6,Status Register 6" line.long 0x1C "STS7,Status Register 7" line.long 0x20 "STS8,Status Register 8" line.long 0x24 "STS9,Status Register 9" line.long 0x28 "STS10,Status Register 10" line.long 0x2C "STS11,Status Register 11" line.long 0x30 "STS12,Status Register 12" hexmask.long 0x30 0.--31. 1. "NDADDR,This field indicating the last write address (AXI command) to NAND device (without base address in SEMC_BR4)." line.long 0x34 "STS13,Status Register 13" hexmask.long.byte 0x34 8.--13. 1. "REFSEL,Sample clock reference delay line delay cell number selection." hexmask.long.byte 0x34 2.--7. 1. "SLVSEL,Sample clock slave delay line delay cell number selection." newline bitfld.long 0x34 1. "REFLOCK,Sample clock reference delay line locked." "0: Reference delay line is not locked.,1: Reference delay line is locked." bitfld.long 0x34 0. "SLVLOCK,Sample clock slave delay line locked." "0: Slave delay line is not locked.,1: Slave delay line is locked." line.long 0x38 "STS14,Status Register 14" line.long 0x3C "STS15,Status Register 15" group.long 0x100++0xB line.long 0x0 "BR9,Base Register 9" hexmask.long.tbyte 0x0 12.--31. 1. "BA,Base Address" hexmask.long.byte 0x0 1.--5. 1. "MS,Memory size" newline bitfld.long 0x0 0. "VLD,Valid" "0: The memory is invalid can not be accessed.,1: The memory is valid can be accessed." line.long 0x4 "BR10,Base Register 10" hexmask.long.tbyte 0x4 12.--31. 1. "BA,Base Address" hexmask.long.byte 0x4 1.--5. 1. "MS,Memory size" newline bitfld.long 0x4 0. "VLD,Valid" "0: The memory is invalid can not be accessed.,1: The memory is valid can be accessed." line.long 0x8 "BR11,Base Register 11" hexmask.long.tbyte 0x8 12.--31. 1. "BA,Base Address" hexmask.long.byte 0x8 1.--5. 1. "MS,Memory size" newline bitfld.long 0x8 0. "VLD,Valid" "0: The memory is invalid can not be accessed.,1: The memory is valid can be accessed." group.long 0x120++0xB line.long 0x0 "SRAMCR4,SRAM Control Register 4" hexmask.long.byte 0x0 12.--15. 1. "COL,Column Address bit width" bitfld.long 0x0 11. "ADVH,ADV# level control during address hold state" "0: ADV# is high during address hold state.,1: ADV# is low during address hold state." newline bitfld.long 0x0 10. "ADVP,ADV# polarity" "0: ADV# is active low.,1: ADV# is active high." bitfld.long 0x0 8.--9. "AM,Address Mode" "0: Address/Data MUX mode (ADMUX),1: Advanced Address/Data MUX mode (AADM),2: Address/Data non-MUX mode (Non-ADMUX),3: Address/Data non-MUX mode (Non-ADMUX)" newline bitfld.long 0x0 4.--6. "BL,Burst Length" "0: 1,1: 2,2: 4,3: 8,4: 16,5: 32,6: 64,7: 64" bitfld.long 0x0 3. "WAITSP,Wait Sample" "0: Wait pin is directly used by the SEMC.,1: Wait pin is sampled by internal clock before it.." newline bitfld.long 0x0 2. "WAITEN,Wait Enable" "0: The SEMC does not monitor wait pin.,1: The SEMC monitors wait pin. The SEMC does not.." bitfld.long 0x0 1. "SYNCEN,Synchronous Mode Enable" "0: Asynchronous mode is enabled.,1: Synchronous mode is enabled. Only fixed latency.." newline bitfld.long 0x0 0. "PS,Port Size" "0: 8bit,1: 16bit" line.long 0x4 "SRAMCR5,SRAM Control Register 5" hexmask.long.byte 0x4 28.--31. 1. "REH,RE high time" hexmask.long.byte 0x4 24.--27. 1. "REL,RE low time" newline hexmask.long.byte 0x4 20.--23. 1. "WEH,WE high time" hexmask.long.byte 0x4 16.--19. 1. "WEL,WE low time" newline hexmask.long.byte 0x4 12.--15. 1. "AH,Address hold time" hexmask.long.byte 0x4 8.--11. 1. "AS,Address setup time" newline hexmask.long.byte 0x4 4.--7. 1. "CEH,CE hold time" hexmask.long.byte 0x4 0.--3. 1. "CES,CE setup time" line.long 0x8 "SRAMCR6,SRAM Control Register 6" hexmask.long.byte 0x8 28.--31. 1. "RDH,Read hold time" hexmask.long.byte 0x8 24.--27. 1. "CEITV,CE# interval time" newline hexmask.long.byte 0x8 20.--23. 1. "RD,Read time" hexmask.long.byte 0x8 16.--19. 1. "LC,Latency count" newline hexmask.long.byte 0x8 12.--15. 1. "AWDH,Address to write data hold time" hexmask.long.byte 0x8 8.--11. 1. "TA,Turnaround time" newline hexmask.long.byte 0x8 4.--7. 1. "WDH,Write Data hold time" hexmask.long.byte 0x8 0.--3. 1. "WDS,Write Data setup time" group.long 0x150++0x3 line.long 0x0 "DCCR,Delay Chain Control Register" hexmask.long.byte 0x0 25.--29. 1. "SRAMXVAL,Clock delay line delay cell number selection value for SRAM device 1-3." bitfld.long 0x0 24. "SRAMXEN,Delay chain insertion enable for SRAM device 1-3." "0: Delay chain is not inserted.,1: Delay chain is inserted." newline hexmask.long.byte 0x0 17.--21. 1. "SRAM0VAL,Clock delay line delay cell number selection value for SRAM device 0." bitfld.long 0x0 16. "SRAM0EN,Delay chain insertion enable for SRAM device 0." "0: Delay chain is not inserted.,1: Delay chain is inserted." newline hexmask.long.byte 0x0 9.--13. 1. "NORVAL,Clock delay line delay cell number selection value for NOR device." bitfld.long 0x0 8. "NOREN,Delay chain insertion enable for NOR device." "0: Delay chain is not inserted.,1: Delay chain is inserted." newline hexmask.long.byte 0x0 1.--5. 1. "SDRAMVAL,Clock delay line delay cell number selection value for SDRAM device." bitfld.long 0x0 0. "SDRAMEN,Delay chain insertion enable for SRAM device." "0: Delay chain is not inserted.,1: Delay chain is inserted." tree.end tree "SNVS" base ad:0x40C90000 group.long 0x0++0x1F line.long 0x0 "HPLR,SNVS_HP Lock Register" bitfld.long 0x0 28. "AT5_SL,Active Tamper 5 Soft Lock When set prevents any writes to the Active Tamper 5 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x0 27. "AT4_SL,Active Tamper 4 Soft Lock When set prevents any writes to the Active Tamper 4 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x0 26. "AT3_SL,Active Tamper 3 Soft Lock When set prevents any writes to the Active Tamper 3 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x0 25. "AT2_SL,Active Tamper 2 Soft Lock When set prevents any writes to the Active Tamper 2 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x0 24. "AT1_SL,Active Tamper 1 Soft Lock When set prevents any writes to the Active Tamper 1 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x0 18. "HAC_L,High Assurance Counter Lock When set prevents any writes to HPHACIVR HPHACR and HAC_EN bit of HPCOMR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 17. "HPSICR_L,HP Security Interrupt Control Register Lock When set prevents any writes to the HPSICR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 16. "HPSVCR_L,HP Security Violation Control Register Lock When set prevents any writes to the HPSVCR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 9. "MKS_SL,Master Key Select Soft Lock When set prevents any writes to the MASTER_KEY_SEL field of the LPMKCR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 8. "LPSECR_SL,LP Security Events Configuration Register Soft Lock When set prevents any writes to the LPSECR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 7. "LPTGFCR_SL,LP Tamper Glitch Filter Configuration Register Soft Lock When set prevents any writes to the LPTGFCR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 6. "LPSVCR_SL,LP Security Violation Control Register Soft Lock When set prevents any writes to the LPSVCR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 5. "GPR_SL,General Purpose Register Soft Lock When set prevents any writes to the GPR" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 4. "MC_SL,Monotonic Counter Soft Lock When set prevents any writes (increments) to the MC Registers and MC_ENV bit" "0: Write access (increment) is allowed,1: Write access (increment) is not allowed" newline bitfld.long 0x0 3. "LPCALB_SL,LP Calibration Soft Lock When set prevents any writes to the LP Calibration Value (LPCALB_VAL) and LP Calibration Enable (LPCALB_EN)" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 2. "SRTC_SL,Secure Real Time Counter Soft Lock When set prevents any writes to the SRTC Registers SRTC_ENV and SRTC_INV_EN bits" "0: Write access is allowed,1: Write access is not allowed" newline bitfld.long 0x0 1. "ZMK_RSL,Zeroizable Master Key Read Soft Lock When set prevents any software reads to the ZMK Registers and ZMK_ECC_VALUE field of the LPMKCR" "0: Read access is allowed (only in software..,1: Read access is not allowed" newline bitfld.long 0x0 0. "ZMK_WSL,Zeroizable Master Key Write Soft Lock When set prevents any writes (software and hardware) to the ZMK registers and the ZMK_HWP ZMK_VAL and ZMK_ECC_EN fields of the LPMKCR" "0: Write access is allowed,1: Write access is not allowed" line.long 0x4 "HPCOMR,SNVS_HP Command Register" bitfld.long 0x4 31. "NPSWA_EN,Non-Privileged Software Access Enable When set allows non-privileged software to access all SNVS registers including those that are privileged software read/write access only" "0,1" newline bitfld.long 0x4 19. "HAC_STOP,High Assurance Counter Stop This bit can be set only when SSM is in soft fail state" "0,1" newline bitfld.long 0x4 18. "HAC_CLEAR,High Assurance Counter Clear When set it clears the High Assurance Counter Register" "0: No Action,1: Clear the HAC" newline bitfld.long 0x4 17. "HAC_LOAD,High Assurance Counter Load When set it loads the High Assurance Counter Register with the value of the High Assurance Counter Load Register" "0: No Action,1: Load the HAC" newline bitfld.long 0x4 16. "HAC_EN,High Assurance Counter Enable This bit controls the SSM transition from the soft fail to the hard fail state" "0: High Assurance Counter is disabled,1: High Assurance Counter is enabled" newline bitfld.long 0x4 13. "MKS_EN,Master Key Select Enable When not set the one time programmable (OTP) master key is selected by default" "0: OTP master key is selected as an SNVS master key,1: SNVS master key is selected according to the.." newline bitfld.long 0x4 12. "PROG_ZMK,Program Zeroizable Master Key This bit activates ZMK hardware programming mechanism" "0: No Action,1: Activate hardware key programming mechanism" newline bitfld.long 0x4 10. "SW_LPSV,LP Software Security Violation When set SNVS_LP treats this bit as a security violation" "0,1" newline bitfld.long 0x4 9. "SW_FSV,Software Fatal Security Violation When set the system security monitor treats this bit as a fatal security violation" "0,1" newline bitfld.long 0x4 8. "SW_SV,Software Security Violation When set the system security monitor treats this bit as a non-fatal security violation" "0,1" newline bitfld.long 0x4 5. "LP_SWR_DIS,LP Software Reset Disable When set disables the LP software reset" "0: LP software reset is enabled,1: LP software reset is disabled" newline bitfld.long 0x4 4. "LP_SWR,LP Software Reset When set to 1 most registers in the SNVS_LP section are reset but the following registers are not reset by an LP software reset: Monotonic Counter Secure Real Time Counter Time Alarm Register This bit cannot be set when the.." "0: No Action,1: Reset LP section" newline bitfld.long 0x4 2. "SSM_SFNS_DIS,SSM Soft Fail to Non-Secure State Transition Disable When set it disables the SSM transition from soft fail to non-secure state" "0: Soft Fail to Non-Secure State transition is..,1: Soft Fail to Non-Secure State transition is.." newline bitfld.long 0x4 1. "SSM_ST_DIS,SSM Secure to Trusted State Transition Disable When set disables the SSM transition from secure to trusted state" "0: Secure to Trusted State transition is enabled,1: Secure to Trusted State transition is disabled" newline bitfld.long 0x4 0. "SSM_ST,SSM State Transition Transition state of the system security monitor" "0,1" line.long 0x8 "HPCR,SNVS_HP Control Register" bitfld.long 0x8 27. "BTN_MASK,Button interrupt mask" "0,1" newline bitfld.long 0x8 24.--26. "BTN_CONFIG,Button Configuration" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 16. "HP_TS,HP Time Synchronize" "0: No Action,1: Synchronize the HP Time Counter to the LP Time.." newline hexmask.long.byte 0x8 10.--14. 1. "HPCALB_VAL,HP Calibration Value Defines signed calibration value for the HP Real Time Counter" newline bitfld.long 0x8 8. "HPCALB_EN,HP Real Time Counter Calibration Enabled Indicates that the time calibration mechanism is enabled." "0: HP Timer calibration disabled,1: HP Timer calibration enabled" newline hexmask.long.byte 0x8 4.--7. 1. "PI_FREQ,Periodic Interrupt Frequency Defines frequency of the periodic interrupt" newline bitfld.long 0x8 3. "PI_EN,HP Periodic Interrupt Enable The periodic interrupt can be generated only if the HP Real Time Counter is enabled" "0: HP Periodic Interrupt is disabled,1: HP Periodic Interrupt is enabled" newline bitfld.long 0x8 2. "DIS_PI,Disable periodic interrupt in the functional interrupt" "0: Periodic interrupt will trigger a functional..,1: Disable periodic interrupt in the function.." newline bitfld.long 0x8 1. "HPTA_EN,HP Time Alarm Enable When set the time alarm interrupt is generated if the value in the HP Time Alarm Registers is equal to the value of the HP Real Time Counter" "0: HP Time Alarm Interrupt is disabled,1: HP Time Alarm Interrupt is enabled" newline bitfld.long 0x8 0. "RTC_EN,HP Real Time Counter Enable" "0: RTC is disabled,1: RTC is enabled" line.long 0xC "HPSICR,SNVS_HP Security Interrupt Control Register" bitfld.long 0xC 31. "LPSVI_EN,LP Security Violation Interrupt Enable This bit enables generating of the security interrupt to the host processor upon security violation signal from the LP section" "0: LP Security Violation Interrupt is Disabled,1: LP Security Violation Interrupt is Enabled" newline bitfld.long 0xC 5. "OCOTP_EN,OCOTP attack error Interrupt Enable Setting this bit to 1 enables generation of the security interrupt to the host processor upon detection of the OCOTP attack error security violation" "0: OCOTP attack error Interrupt is Disabled,1: OCOTP attack error Interrupt is Enabled" newline bitfld.long 0xC 4. "SRC_EN,Internal Boot Interrupt Enable Setting this bit to 1 enables generation of the security interrupt to the host processor upon detection of the Internal Boot security violation" "0: Internal Boot Interrupt is Disabled,1: Internal Boot Interrupt is Enabled" newline bitfld.long 0xC 2. "WDOG2_EN,Watchdog 2 Reset Interrupt Enable Setting this bit to 1 enables generation of the security interrupt to the host processor upon detection of the Watchdog 2 Reset security violation" "0: Watchdog 2 Reset Interrupt is Disabled,1: Watchdog 2 Reset Interrupt is Enabled" newline bitfld.long 0xC 1. "JTAGC_EN,JTAG Active Interrupt Enable Setting this bit to 1 enables generation of the security interrupt to the host processor upon detection of the JTAG Active security violation" "0: JTAG Active Interrupt is Disabled,1: JTAG Active Interrupt is Enabled" newline bitfld.long 0xC 0. "CAAM_EN,CAAM Security Violation Interrupt Enable Setting this bit to 1 enables generation of the security interrupt to the host processor upon detection of the CAAM Security Violation security violation" "0: CAAM Security Violation Interrupt is Disabled,1: CAAM Security Violation Interrupt is Enabled" line.long 0x10 "HPSVCR,SNVS_HP Security Violation Control Register" bitfld.long 0x10 30.--31. "LPSV_CFG,LP Security Violation Configuration This field configures the LP security violation source." "0: LP security violation is a fatal violation,1: LP security violation is a non-fatal violation,2: LP security violation is a fatal violation,3: LP security violation is a fatal violation" newline bitfld.long 0x10 5.--6. "OCOTP_CFG,OCOTP attack error Security Violation Configuration This field configures the OCOTP attack error Security Violation Input" "0: OCOTP attack error is a fatal violation,1: OCOTP attack error is a non-fatal violation,2: OCOTP attack error is a fatal violation,3: OCOTP attack error is a fatal violation" newline bitfld.long 0x10 4. "SRC_CFG,Internal Boot Security Violation Configuration This field configures the Internal Boot Security Violation Input" "0: Internal Boot is a non-fatal violation,1: Internal Boot is a fatal violation" newline bitfld.long 0x10 2. "WDOG2_CFG,Watchdog 2 Reset Security Violation Configuration This field configures the Watchdog 2 Reset Security Violation Input" "0: Watchdog 2 Reset is a non-fatal violation,1: Watchdog 2 Reset is a fatal violation" newline bitfld.long 0x10 1. "JTAGC_CFG,JTAG Active Security Violation Configuration This field configures the JTAG Active Security Violation Input" "0: JTAG Active is a non-fatal violation,1: JTAG Active is a fatal violation" newline bitfld.long 0x10 0. "CAAM_CFG,CAAM Security Violation Security Violation Configuration This field configures the CAAM Security Violation Security Violation Input" "0: CAAM Security Violation is a non-fatal violation,1: CAAM Security Violation is a fatal violation" line.long 0x14 "HPSR,SNVS_HP Status Register" rbitfld.long 0x14 31. "ZMK_ZERO,Zeroizable Master Key is Equal to Zero" "0: The ZMK is not zero.,1: The ZMK is zero." newline rbitfld.long 0x14 27. "OTPMK_ZERO,One Time Programmable Master Key is Equal to Zero" "0: The OTPMK is not zero.,1: The OTPMK is zero." newline rbitfld.long 0x14 15. "SYS_SECURE_BOOT,System Secure Boot If SYS_SECURE_BOOT is 1 the chip boots from internal ROM" "0,1" newline rbitfld.long 0x14 12.--14. "SYS_SECURITY_CFG,System Security Configuration This field reflects the three security configuration inputs to SNVS" "0: Fab Configuration - the default configuration of..,1: Open Configuration - the configuration after..,?,3: Closed Configuration - the configuration after..,?,?,?,7: Field Return Configuration - the configuration.." newline hexmask.long.byte 0x14 8.--11. 1. "SSM_STATE,System Security Monitor State This field contains the encoded state of the SSM's state machine" newline eventfld.long 0x14 7. "BI,Button Interrupt Signal ipi_snvs_btn_int_b was asserted." "0,1" newline rbitfld.long 0x14 6. "BTN,Button Value of the BTN input" "0,1" newline rbitfld.long 0x14 4. "LPDIS,Low Power Disable If 1 the low power section has been disabled by means of an input signal to SNVS" "0,1" newline eventfld.long 0x14 1. "PI,Periodic Interrupt Indicates that periodic interrupt has occurred since this bit was last cleared." "0: No periodic interrupt occurred.,1: A periodic interrupt occurred." newline eventfld.long 0x14 0. "HPTA,HP Time Alarm Indicates that the HP Time Alarm has occurred since this bit was last cleared." "0: No time alarm interrupt occurred.,1: A time alarm interrupt occurred." line.long 0x18 "HPSVSR,SNVS_HP Security Violation Status Register" rbitfld.long 0x18 31. "LP_SEC_VIO,LP Security Violation A security volation was detected in the SNVS low power section" "0,1" newline eventfld.long 0x18 27. "ZMK_ECC_FAIL,Zeroizable Master Key Error Correcting Code Check Failure When set this bit triggers a bad key violation to the SSM and a security violation to the SNVS_LP section which clears security sensitive data" "0: ZMK ECC Failure was not detected.,1: ZMK ECC Failure was detected." newline hexmask.long.word 0x18 16.--24. 1. "ZMK_SYNDROME,Zeroizable Master Key Syndrome The ZMK syndrome indicates the single-bit error location and parity for the ZMK register" newline rbitfld.long 0x18 15. "SW_LPSV,LP Software Security Violation This bit is a read-only copy of the SW_LPSV bit in the HP Command Register" "0,1" newline rbitfld.long 0x18 14. "SW_FSV,Software Fatal Security Violation This bit is a read-only copy of the SW_FSV bit in the HP Command Register" "0,1" newline rbitfld.long 0x18 13. "SW_SV,Software Security Violation This bit is a read-only copy of the SW_SV bit in the HP Command Register" "0,1" newline eventfld.long 0x18 5. "OCOTP,OCOTP attack error security violation was detected." "0: No OCOTP attack error security violation was..,1: OCOTP attack error security violation was.." newline eventfld.long 0x18 4. "SRC,Internal Boot security violation was detected." "0: No Internal Boot security violation was detected.,1: Internal Boot security violation was detected." newline eventfld.long 0x18 2. "WDOG2,Watchdog 2 Reset security violation was detected." "0: No Watchdog 2 Reset security violation was..,1: Watchdog 2 Reset security violation was detected." newline eventfld.long 0x18 1. "JTAGC,JTAG Active security violation was detected." "0: No JTAG Active security violation was detected.,1: JTAG Active security violation was detected." newline eventfld.long 0x18 0. "CAAM,CAAM Security Violation security violation was detected." "0: No CAAM Security Violation security violation..,1: CAAM Security Violation security violation was.." line.long 0x1C "HPHACIVR,SNVS_HP High Assurance Counter IV Register" hexmask.long 0x1C 0.--31. 1. "HAC_COUNTER_IV,High Assurance Counter Initial Value This register is used to set the starting count value to the high assurance counter" rgroup.long 0x20++0x3 line.long 0x0 "HPHACR,SNVS_HP High Assurance Counter Register" hexmask.long 0x0 0.--31. 1. "HAC_COUNTER,High Assurance Counter When the HAC_EN bit is set and the SSM is in the soft fail state this counter starts to count down with the system clock" group.long 0x24++0x47 line.long 0x0 "HPRTCMR,SNVS_HP Real Time Counter MSB Register" hexmask.long.word 0x0 0.--14. 1. "RTC,HP Real Time Counter The most-significant 15 bits of the RTC" line.long 0x4 "HPRTCLR,SNVS_HP Real Time Counter LSB Register" hexmask.long 0x4 0.--31. 1. "RTC,HP Real Time Counter least-significant 32 bits" line.long 0x8 "HPTAMR,SNVS_HP Time Alarm MSB Register" hexmask.long.word 0x8 0.--14. 1. "HPTA_MS,HP Time Alarm most-significant 15 bits" line.long 0xC "HPTALR,SNVS_HP Time Alarm LSB Register" hexmask.long 0xC 0.--31. 1. "HPTA_LS,HP Time Alarm 32 least-significant bits" line.long 0x10 "LPLR,SNVS_LP Lock Register" bitfld.long 0x10 28. "AT5_HL,Active Tamper 5 Hard Lock When set prevents any writes to the Active Tamper 5 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 27. "AT4_HL,Active Tamper 4 Hard Lock When set prevents any writes to the Active Tamper 4 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 26. "AT3_HL,Active Tamper 3 Hard Lock When set prevents any writes to the Active Tamper 3 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 25. "AT2_HL,Active Tamper 2 Hard Lock When set prevents any writes to the Active Tamper 2 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 24. "AT1_HL,Active Tamper 1 Hard Lock When set prevents any writes to the Active Tamper 1 registers" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 9. "MKS_HL,Master Key Select Hard Lock When set prevents any writes to the MASTER_KEY_SEL field of the LP Master Key Control Register" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 8. "LPSECR_HL,LP Security Events Configuration Register Hard Lock When set prevents any writes to the LPSECR" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 7. "LPTGFCR_HL,LP Tamper Glitch Filter Configuration Register Hard Lock When set prevents any writes to the LPTGFCR" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 6. "LPSVCR_HL,LP Security Violation Control Register Hard Lock When set prevents any writes to the LPSVCR" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 5. "GPR_HL,General Purpose Register Hard Lock When set prevents any writes to the GPR" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 4. "MC_HL,Monotonic Counter Hard Lock When set prevents any writes (increments) to the MC Registers and MC_ENV bit" "0: Write access (increment) is allowed.,1: Write access (increment) is not allowed." newline bitfld.long 0x10 3. "LPCALB_HL,LP Calibration Hard Lock When set prevents any writes to the LP Calibration Value (LPCALB_VAL) and LP Calibration Enable (LPCALB_EN)" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 2. "SRTC_HL,Secure Real Time Counter Hard Lock When set prevents any writes to the SRTC registers SRTC_ENV and SRTC_INV_EN bits" "0: Write access is allowed.,1: Write access is not allowed." newline bitfld.long 0x10 1. "ZMK_RHL,Zeroizable Master Key Read Hard Lock When set prevents any software reads to the ZMK registers and ZMK_ECC_VALUE field of the LPMKCR" "0: Read access is allowed (only in software..,1: Read access is not allowed." newline bitfld.long 0x10 0. "ZMK_WHL,Zeroizable Master Key Write Hard Lock When set prevents any writes (software and hardware) to the ZMK registers and ZMK_HWP ZMK_VAL and ZMK_ECC_EN fields of the LPMKCR" "0: Write access is allowed.,1: Write access is not allowed." line.long 0x14 "LPCR,SNVS_LP Control Register" bitfld.long 0x14 24. "GPR_Z_DIS,General Purpose Registers Zeroization Disable" "0,1" newline bitfld.long 0x14 23. "PK_OVERRIDE,PMIC On Request Override The value written to PK_OVERRIDE will be asserted on output signal snvs_lp_pk_override" "0,1" newline bitfld.long 0x14 22. "PK_EN,PMIC On Request Enable The value written to PK_EN will be asserted on output signal snvs_lp_pk_en" "0,1" newline bitfld.long 0x14 20.--21. "ON_TIME,The ON_TIME field is used to configure the period of time after BTN is asserted before pmic_en_b is asserted to turn on the SoC power" "0,1,2,3" newline bitfld.long 0x14 18.--19. "DEBOUNCE,This field configures the amount of debounce time for the BTN input signal" "0,1,2,3" newline bitfld.long 0x14 16.--17. "BTN_PRESS_TIME,This field configures the button press time out values for the PMIC Logic" "0,1,2,3" newline hexmask.long.byte 0x14 10.--14. 1. "LPCALB_VAL,LP Calibration Value Defines signed calibration value for SRTC" newline bitfld.long 0x14 8. "LPCALB_EN,LP Calibration Enable When set enables the SRTC calibration mechanism" "0: SRTC Time calibration is disabled.,1: SRTC Time calibration is enabled." newline bitfld.long 0x14 7. "LVD_EN,Digital Low-Voltage Event Enable By default the detection of a low-voltage event does not cause the pmic_en_b signal to be asserted" "0,1" newline bitfld.long 0x14 6. "TOP,Turn off System Power Asserting this bit causes a signal to be sent to the Power Management IC to turn off the system power" "0: Leave system power on.,1: Turn off system power." newline bitfld.long 0x14 5. "DP_EN,Dumb PMIC Enabled When set software can control the system power" "0: Smart PMIC enabled.,1: Dumb PMIC enabled." newline bitfld.long 0x14 4. "SRTC_INV_EN,If this bit is 1 in the case of a security violation the SRTC stops counting and the SRTC is invalidated (SRTC_ENV bit is cleared)" "0: SRTC stays valid in the case of security..,1: SRTC is invalidated in the case of security.." newline bitfld.long 0x14 3. "LPWUI_EN,LP Wake-Up Interrupt Enable This interrupt line should be connected to the external pin and is intended to inform the external chip about an SNVS_LP event (tamper event MC rollover SRTC rollover or time alarm )" "0,1" newline bitfld.long 0x14 2. "MC_ENV,Monotonic Counter Enabled and Valid When set the MC can be incremented (by write transaction to the LPSMCMR or LPSMCLR)" "0: MC is disabled or invalid.,1: MC is enabled and valid." newline bitfld.long 0x14 1. "LPTA_EN,LP Time Alarm Enable When set the SNVS functional interrupt is asserted if the LP Time Alarm Register is equal to the 32 MSBs of the secure real time counter" "0: LP time alarm interrupt is disabled.,1: LP time alarm interrupt is enabled." newline bitfld.long 0x14 0. "SRTC_ENV,Secure Real Time Counter Enabled and Valid When set the SRTC becomes operational" "0: SRTC is disabled or invalid.,1: SRTC is enabled and valid." line.long 0x18 "LPMKCR,SNVS_LP Master Key Control Register" hexmask.long.word 0x18 7.--15. 1. "ZMK_ECC_VALUE,Zeroizable Master Key Error Correcting Code Value This field is automatically calculated and set when one is written into ZMK_ECC_EN bit of this register" newline bitfld.long 0x18 4. "ZMK_ECC_EN,Zeroizable Master Key Error Correcting Code Check Enable Writing one to this field automatically calculates and sets the ZMK ECC value in the ZMK_ECC_VALUE field of this register" "0: ZMK ECC check is disabled.,1: ZMK ECC check is enabled." newline bitfld.long 0x18 3. "ZMK_VAL,Zeroizable Master Key Valid When set the ZMK value can be selected by the master key control block for use by cryptographic modules" "0: ZMK is not valid.,1: ZMK is valid." newline bitfld.long 0x18 2. "ZMK_HWP,Zeroizable Master Key hardware Programming mode When set only the hardware key programming mechanism can set the ZMK and software cannot read it" "0: ZMK is in the software programming mode.,1: ZMK is in the hardware programming mode." newline bitfld.long 0x18 0.--1. "MASTER_KEY_SEL,Master Key Select These bits select the SNVS Master Key output when Master Key Select bits are enabled by MKS_EN bit in the HPCOMR" "0: Select one time programmable master key.,1: Select one time programmable master key.,2: Select zeroizable master key when MKS_EN bit is..,3: Select combined master key when MKS_EN bit is.." line.long 0x1C "LPSVCR,SNVS_LP Security Violation Control Register" bitfld.long 0x1C 5. "OCOTP_EN,OCOTP attack error Enable This bit enables OCOTP attack error Input" "0: OCOTP attack error is disabled in the LP domain.,1: OCOTP attack error is enabled in the LP domain." newline bitfld.long 0x1C 4. "SRC_EN,Internal Boot Enable This bit enables Internal Boot Input" "0: Internal Boot is disabled in the LP domain.,1: Internal Boot is enabled in the LP domain." newline bitfld.long 0x1C 2. "WDOG2_EN,Watchdog 2 Reset Enable This bit enables Watchdog 2 Reset Input" "0: Watchdog 2 Reset is disabled in the LP domain.,1: Watchdog 2 Reset is enabled in the LP domain." newline bitfld.long 0x1C 1. "JTAGC_EN,JTAG Active Enable This bit enables JTAG Active Input" "0: JTAG Active is disabled in the LP domain.,1: JTAG Active is enabled in the LP domain." newline bitfld.long 0x1C 0. "CAAM_EN,CAAM Security Violation Enable This bit enables CAAM Security Violation Input" "0: CAAM Security Violation is disabled in the LP..,1: CAAM Security Violation is enabled in the LP.." line.long 0x20 "LPTGFCR,SNVS_LP Tamper Glitch Filters Configuration Register" bitfld.long 0x20 31. "ETGF2_EN,External Tamper Glitch Filter 2 Enable When set enables the external tamper glitch filter 2." "0: External tamper glitch filter 2 is bypassed.,1: External tamper glitch filter 2 is enabled." newline hexmask.long.byte 0x20 24.--30. 1. "ETGF2,External Tamper Glitch Filter 2 Configures the length of the digital glitch filter for the external tamper 2 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0x20 23. "ETGF1_EN,External Tamper Glitch Filter 1 Enable When set enables the external tamper glitch filter 1." "0: External tamper glitch filter 1 is bypassed.,1: External tamper glitch filter 1 is enabled." newline hexmask.long.byte 0x20 16.--22. 1. "ETGF1,External Tamper Glitch Filter 1 Configures the length of the digital glitch filter for the external tamper 1 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0x20 7. "WMTGF_EN,Wire-Mesh Tamper Glitch Filter Enable When set enables the wire-mesh tamper glitch filter" "0: Wire-mesh tamper glitch filter is bypassed.,1: Wire-mesh tamper glitch filter is enabled." newline hexmask.long.byte 0x20 0.--4. 1. "WMTGF,Wire-Mesh Tamper Glitch Filter Configures the length of the digital glitch filter for the wire-mesh tamper 1 and 2 pins between 1 and 63 SRTC clock cycles" line.long 0x24 "LPTDCR,SNVS_LP Tamper Detect Configuration Register" bitfld.long 0x24 28. "OSCB,Oscillator Bypass When OSCB=1 the osc_bypass signal is asserted" "0: Normal SRTC clock oscillator not bypassed.,1: Normal SRTC clock oscillator bypassed. Alternate.." newline bitfld.long 0x24 24.--26. "VRC,Voltage Reference Configuration These configuration bits are wired as an output of the module." "0,1,2,3,4,5,6,7" newline bitfld.long 0x24 20.--22. "HTDC,High Temperature Detect Configuration These configuration bits are wired as an output of the module" "0,1,2,3,4,5,6,7" newline bitfld.long 0x24 16.--18. "LTDC,Low Temp Detect Configuration These configuration bits are wired as an output of the module." "0,1,2,3,4,5,6,7" newline bitfld.long 0x24 15. "POR_OBSERV,Power On Reset (POR) Observability Flop The asynchronous reset input of this flop is connected directly to the output of the POR analog circuitry (external to the SNVS" "0,1" newline bitfld.long 0x24 14. "PFD_OBSERV,System Power Fail Detector (PFD) Observability Flop The asynchronous reset input of this flop is connected directly to the inverted output of the PFD analog circuitry (external to the SNVS block)" "0,1" newline bitfld.long 0x24 12. "ET2P,External Tampering 2 Polarity This bit is used to determine the polarity of external tamper 2." "0: External tamper 2 is active low.,1: External tamper 2 is active high." newline bitfld.long 0x24 11. "ET1P,External Tampering 1 Polarity This bit is used to determine the polarity of external tamper 1." "0: External tamper 1 is active low.,1: External tamper 1 is active high." newline bitfld.long 0x24 10. "ET2_EN,External Tampering 2 Enable When set external tampering 2 detection generates an LP security violation" "0: External tamper 2 is disabled.,1: External tamper 2 is enabled." newline bitfld.long 0x24 9. "ET1_EN,External Tampering 1 Enable When set external tampering 1 detection generates an LP security violation" "0: External tamper 1 is disabled.,1: External tamper 1 is enabled." newline bitfld.long 0x24 8. "WMT2_EN,Wire-Mesh Tampering 2 Enable When set wire-mesh tampering 2 detection generates an LP security violation" "0: Wire-mesh tamper 2 is disabled.,1: Wire-mesh tamper 2 is enabled." newline bitfld.long 0x24 7. "WMT1_EN,Wire-Mesh Tampering 1 Enable When set wire-mesh tampering 1 detection generates an LP security violation" "0: Wire-mesh tamper 1 is disabled.,1: Wire-mesh tamper 1 is enabled." newline bitfld.long 0x24 6. "VT_EN,Voltage Tamper Enable Voltage Tamper Enable should be enabled 500 us after setting SCSC_SOSC_CTR [VOLT_TEMP_TAMPER_EN]" "0: Voltage tamper is disabled.,1: Voltage tamper is enabled." newline bitfld.long 0x24 5. "TT_EN,Temperature Tamper Enable When set a temperature monitor tamper generates an LP security violation" "0: Temperature tamper is disabled.,1: Temperature tamper is enabled." newline bitfld.long 0x24 4. "CT_EN,Clock Tamper Enable When set a clock monitor tamper generates an LP security violation." "0: Clock tamper is disabled.,1: Clock tamper is enabled." newline bitfld.long 0x24 2. "MCR_EN,MC Rollover Enable When set an MC Rollover event generates an LP security violation." "0: MC rollover is disabled.,1: MC rollover is enabled." newline bitfld.long 0x24 1. "SRTCR_EN,SRTC Rollover Enable When set an SRTC rollover event generates an LP security violation." "0: SRTC rollover is disabled.,1: SRTC rollover is enabled." line.long 0x28 "LPSR,SNVS_LP Status Register" rbitfld.long 0x28 31. "LPS,LP Section is Secured Indicates that the LP section is provisioned/programmed in the secure or trusted state" "0: LP section was not programmed in secure or..,1: LP section was programmed in secure or trusted.." newline rbitfld.long 0x28 30. "LPNS,LP Section is Non-Secured Indicates that LP section was provisioned/programmed in the non-secure state" "0: LP section was not programmed in the non-secure..,1: LP section was programmed in the non-secure state." newline eventfld.long 0x28 18. "SPOF,Set Power Off The SPO bit is set when the power button is pressed longer than the configured debounce time" "0: Set Power Off was not detected.,1: Set Power Off was detected." newline eventfld.long 0x28 17. "EO,Emergency Off This bit is set when a power off is requested." "0: Emergency off was not detected.,1: Emergency off was detected." newline eventfld.long 0x28 16. "ESVD,External Security Violation Detected Indicates that a security violation is detected on one of the HP security violation ports" "0: No external security violation.,1: External security violation is detected." newline eventfld.long 0x28 10. "ET2D,External Tampering 2 Detected" "0: External tampering 2 not detected.,1: External tampering 2 detected." newline eventfld.long 0x28 9. "ET1D,External Tampering 1 Detected" "0: External tampering 1 not detected.,1: External tampering 1 detected." newline eventfld.long 0x28 8. "WMT2D,Wire-Mesh Tampering 2 Detected" "0: Wire-mesh tampering 2 not detected.,1: Wire-mesh tampering 2 detected." newline eventfld.long 0x28 7. "WMT1D,Wire-Mesh Tampering 1 Detected" "0: Wire-mesh tampering 1 not detected.,1: Wire-mesh tampering 1 detected." newline eventfld.long 0x28 6. "VTD,Voltage Tampering Detected" "0: Voltage tampering not detected.,1: Voltage tampering detected." newline eventfld.long 0x28 5. "TTD,Temperature Tamper Detected" "0: No temperature tamper.,1: Temperature tamper is detected." newline eventfld.long 0x28 4. "CTD,Clock Tampering Detected" "0: No clock tamper.,1: Clock tamper is detected." newline eventfld.long 0x28 3. "LVD,Digital Low Voltage Event Detected" "0: No low voltage event detected.,1: Low voltage event is detected." newline eventfld.long 0x28 2. "MCR,Monotonic Counter Rollover" "0: MC has not reached its maximum value.,1: MC has reached its maximum value." newline eventfld.long 0x28 1. "SRTCR,Secure Real Time Counter Rollover" "0: SRTC has not reached its maximum value.,1: SRTC has reached its maximum value." newline eventfld.long 0x28 0. "LPTA,LP Time Alarm" "0: No time alarm interrupt occurred.,1: A time alarm interrupt occurred." line.long 0x2C "LPSRTCMR,SNVS_LP Secure Real Time Counter MSB Register" hexmask.long.word 0x2C 0.--14. 1. "SRTC,LP Secure Real Time Counter The most-significant 15 bits of the SRTC" line.long 0x30 "LPSRTCLR,SNVS_LP Secure Real Time Counter LSB Register" hexmask.long 0x30 0.--31. 1. "SRTC,LP Secure Real Time Counter least-significant 32 bits This register can be programmed only when SRTC is not active and not locked meaning the SRTC_ENV SRTC_SL and SRTC_HL bits are not set" line.long 0x34 "LPTAR,SNVS_LP Time Alarm Register" hexmask.long 0x34 0.--31. 1. "LPTA,LP Time Alarm This register can be programmed only when the LP time alarm is disabled (LPTA_EN bit is not set)" line.long 0x38 "LPSMCMR,SNVS_LP Secure Monotonic Counter MSB Register" hexmask.long.word 0x38 16.--31. 1. "MC_ERA_BITS,Monotonic Counter Era Bits These bits are inputs to the module and typically connect to fuses" newline hexmask.long.word 0x38 0.--15. 1. "MON_COUNTER,Monotonic Counter most-significant 16 Bits Note that writing to this register does not change the value of this field to the value that was written" line.long 0x3C "LPSMCLR,SNVS_LP Secure Monotonic Counter LSB Register" hexmask.long 0x3C 0.--31. 1. "MON_COUNTER,Monotonic Counter bits Note that writing to this register does not change the value of this field to the value that was written" line.long 0x40 "LPLVDR,SNVS_LP Digital Low-Voltage Detector Register" hexmask.long 0x40 0.--31. 1. "LVD,Low-Voltage Detector Value" line.long 0x44 "LPGPR0_legacy_alias,SNVS_LP General Purpose Register 0 (legacy alias)" hexmask.long 0x44 0.--31. 1. "GPR,General Purpose Register When GPR_SL or GPR_HL bit is set the register cannot be programmed." repeat 8. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x6C)++0x3 line.long 0x0 "LPZMKR[$1],SNVS_LP Zeroizable Master Key Register" hexmask.long 0x0 0.--31. 1. "ZMK,Zeroizable Master Key Each of these registers contains 32 bits of the 256-bit ZMK value" repeat.end repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x90)++0x3 line.long 0x0 "LPGPR_alias[$1],SNVS_LP General Purpose Registers 0 .. 3" hexmask.long 0x0 0.--31. 1. "GPR,General Purpose Register When GPR_SL or GPR_HL bit is set the register cannot be programmed." repeat.end group.long 0xA0++0xF line.long 0x0 "LPTDC2R,SNVS_LP Tamper Detectors Config 2 Register" bitfld.long 0x0 23. "ET10P,External Tampering 10 Polarity This bit is used to determine the polarity of external tamper 10." "0: External tamper 10 is active low.,1: External tamper 10 is active high." newline bitfld.long 0x0 22. "ET9P,External Tampering 9 Polarity This bit is used to determine the polarity of external tamper 9." "0: External tamper 9 is active low.,1: External tamper 9 is active high." newline bitfld.long 0x0 21. "ET8P,External Tampering 8 Polarity This bit is used to determine the polarity of external tamper 8." "0: External tamper 8 is active low.,1: External tamper 8 is active high." newline bitfld.long 0x0 20. "ET7P,External Tampering 7 Polarity This bit is used to determine the polarity of external tamper 7." "0: External tamper 7 is active low.,1: External tamper 7 is active high." newline bitfld.long 0x0 19. "ET6P,External Tampering 6 Polarity This bit is used to determine the polarity of external tamper 6." "0: External tamper 6 is active low.,1: External tamper 6 is active high." newline bitfld.long 0x0 18. "ET5P,External Tampering 5 Polarity This bit is used to determine the polarity of external tamper 5." "0: External tamper 5 is active low.,1: External tamper 5 is active high." newline bitfld.long 0x0 17. "ET4P,External Tampering 4 Polarity This bit is used to determine the polarity of external tamper 4." "0: External tamper 4 is active low.,1: External tamper 4 is active high." newline bitfld.long 0x0 16. "ET3P,External Tampering 3 Polarity This bit is used to determine the polarity of external tamper 3." "0: External tamper 3 active low.,1: External tamper 3 active high." newline bitfld.long 0x0 7. "ET10_EN,External Tampering 10 Enable When set external tampering 10 detection generates an LP security violation" "0: External tamper 10 is disabled.,1: External tamper 10 is enabled." newline bitfld.long 0x0 6. "ET9_EN,External Tampering 9 Enable When set external tampering 9 detection generates an LP security violation" "0: External tamper 9 is disabled.,1: External tamper 9 is enabled." newline bitfld.long 0x0 5. "ET8_EN,External Tampering 8 Enable When set external tampering 8 detection generates an LP security violation" "0: External tamper 8 is disabled.,1: External tamper 8 is enabled." newline bitfld.long 0x0 4. "ET7_EN,External Tampering 7 Enable When set external tampering 7 detection generates an LP security violation" "0: External tamper 7 is disabled.,1: External tamper 7 is enabled." newline bitfld.long 0x0 3. "ET6_EN,External Tampering 6 Enable When set external tampering 6 detection generates an LP security violation" "0: External tamper 6 is disabled.,1: External tamper 6 is enabled." newline bitfld.long 0x0 2. "ET5_EN,External Tampering 5 Enable When set external tampering 5 detection generates an LP security violation" "0: External tamper 5 is disabled.,1: External tamper 5 is enabled." newline bitfld.long 0x0 1. "ET4_EN,External Tampering 4 Enable When set external tampering 4 detection generates an LP security violation" "0: External tamper 4 is disabled.,1: External tamper 4 is enabled." newline bitfld.long 0x0 0. "ET3_EN,External Tampering 3 Enable When set external tampering 3 detection generates an LP security violation" "0: External tamper 3 is disabled.,1: External tamper 3 is enabled." line.long 0x4 "LPTDSR,SNVS_LP Tamper Detectors Status Register" eventfld.long 0x4 7. "ET10D,External Tampering 10 Detected" "0: External tamper 10 is not detected.,1: External tamper 10 is detected." newline eventfld.long 0x4 6. "ET9D,External Tampering 9 Enable When set external tampering 9 detection generates an LP security violation" "0: External tamper 9 is not detected.,1: External tamper 9 is detected." newline eventfld.long 0x4 5. "ET8D,External Tampering 8 Detected" "0: External tamper 8 is not detected.,1: External tamper 8 is detected." newline eventfld.long 0x4 4. "ET7D,External Tampering 7 Detected" "0: External tamper 7 is not detected.,1: External tamper 7 is detected." newline eventfld.long 0x4 3. "ET6D,External Tampering 6 Detected" "0: External tamper 6 is not detected.,1: External tamper 6 is detected." newline eventfld.long 0x4 2. "ET5D,External Tampering 5 Detected" "0: External tamper 5 is not detected.,1: External tamper 5 is detected." newline eventfld.long 0x4 1. "ET4D,External Tampering 4 Detected" "0: External tamper 4 is not detected.,1: External tamper 4 is detected." newline eventfld.long 0x4 0. "ET3D,External Tampering 3 Detected" "0: External tamper 3 is not detected.,1: External tamper 3 is detected." line.long 0x8 "LPTGF1CR,SNVS_LP Tamper Glitch Filter 1 Configuration Register" bitfld.long 0x8 31. "ETGF6_EN,External Tamper Glitch Filter 6 Enable When set enables the external tamper glitch filter 6." "0: External tamper glitch filter 6 is bypassed.,1: External tamper glitch filter 6 is enabled." newline hexmask.long.byte 0x8 24.--30. 1. "ETGF6,External Tamper Glitch Filter 6 Configures the length of the digital glitch filter for the external tamper 6 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0x8 23. "ETGF5_EN,External Tamper Glitch Filter 5 Enable When set enables the external tamper glitch filter 5." "0: External tamper glitch filter 5 is bypassed.,1: External tamper glitch filter 5 is enabled." newline hexmask.long.byte 0x8 16.--22. 1. "ETGF5,External Tamper Glitch Filter 5 Configures the length of the digital glitch filter for the external tamper 5 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0x8 15. "ETGF4_EN,External Tamper Glitch Filter 4 Enable When set enables the external tamper glitch filter 4." "0: External tamper glitch filter 4 is bypassed.,1: External tamper glitch filter 4 is enabled." newline hexmask.long.byte 0x8 8.--14. 1. "ETGF4,External Tamper Glitch Filter 4 Configures the length of the digital glitch filter for the external tamper 4 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0x8 7. "ETGF3_EN,External Tamper Glitch Filter 3 Enable When set enables the external tamper glitch filter 3." "0: External tamper glitch filter 3 is bypassed.,1: External tamper glitch filter 3 is enabled." newline hexmask.long.byte 0x8 0.--6. 1. "ETGF3,External Tamper Glitch Filter 3 Configures the length of the digital glitch filter for the external tamper 3 pin between 128 and 32640 SRTC clock cycles" line.long 0xC "LPTGF2CR,SNVS_LP Tamper Glitch Filter 2 Configuration Register" bitfld.long 0xC 31. "ETGF10_EN,External Tamper Glitch Filter 10 Enable When set enables the external tamper glitch filter 10." "0: External tamper glitch filter 10 is bypassed.,1: External tamper glitch filter 10 is enabled." newline hexmask.long.byte 0xC 24.--30. 1. "ETGF10,External Tamper Glitch Filter 10 Configures the length of the digital glitch filter for the external tamper 10 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0xC 23. "ETGF9_EN,External Tamper Glitch Filter 9 Enable When set enables the external tamper glitch filter 9." "0: External tamper glitch filter 9 is bypassed.,1: External tamper glitch filter 9 is enabled." newline hexmask.long.byte 0xC 16.--22. 1. "ETGF9,External Tamper Glitch Filter 9 Configures the length of the digital glitch filter for the external tamper 9 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0xC 15. "ETGF8_EN,External Tamper Glitch Filter 8 Enable When set enables the external tamper glitch filter 8." "0: External tamper glitch filter 8 is bypassed.,1: External tamper glitch filter 8 is enabled." newline hexmask.long.byte 0xC 8.--14. 1. "ETGF8,External Tamper Glitch Filter 8 Configures the length of the digital glitch filter for the external tamper 8 pin between 128 and 32640 SRTC clock cycles" newline bitfld.long 0xC 7. "ETGF7_EN,External Tamper Glitch Filter 7 Enable When set enables the external tamper glitch filter 7." "0: External tamper glitch filter 7 is bypassed.,1: External tamper glitch filter 7 is enabled." newline hexmask.long.byte 0xC 0.--6. 1. "ETGF7,External Tamper Glitch Filter 7 Configures the length of the digital glitch filter for the external tamper 7 pin between 128 and 32640 SRTC clock cycles" wgroup.long 0xC0++0x13 line.long 0x0 "LPAT1CR,SNVS_LP Active Tamper 1 Configuration Register" hexmask.long.word 0x0 16.--31. 1. "Polynomial,Active Tamper 1 Polynomial Default Polynomial is 8400h." newline hexmask.long.word 0x0 0.--15. 1. "Seed,Active Tamper 1 Initial Seed Default Seed is 1111h." line.long 0x4 "LPAT2CR,SNVS_LP Active Tamper 2 Configuration Register" hexmask.long.word 0x4 16.--31. 1. "Polynomial,Active Tamper 2 Polynomial Default Polynomial is 9C00h." newline hexmask.long.word 0x4 0.--15. 1. "Seed,Active Tamper 2 Initial Seed Default Seed is 2222h." line.long 0x8 "LPAT3CR,SNVS_LP Active Tamper 3 Configuration Register" hexmask.long.word 0x8 16.--31. 1. "Polynomial,Active Tamper 3 Polynomial Default Polynomial is CA00h." newline hexmask.long.word 0x8 0.--15. 1. "Seed,Active Tamper 3 Initial Seed Default Seed is 3333h." line.long 0xC "LPAT4CR,SNVS_LP Active Tamper 4 Configuration Register" hexmask.long.word 0xC 16.--31. 1. "Polynomial,Active Tamper 4 Polynomial Default Polynomial is 8580h." newline hexmask.long.word 0xC 0.--15. 1. "Seed,Active Tamper 4 Initial Seed Default Seed is 4444h." line.long 0x10 "LPAT5CR,SNVS_LP Active Tamper 5 Configuration Register" hexmask.long.word 0x10 16.--31. 1. "Polynomial,Active Tamper 5 Polynomial Default Polynomial is A840h." newline hexmask.long.word 0x10 0.--15. 1. "Seed,Active Tamper 5 Initial Seed Default Seed is 5555h." group.long 0xE0++0xF line.long 0x0 "LPATCTLR,SNVS_LP Active Tamper Control Register" bitfld.long 0x0 20. "AT5_PAD_EN,Active Tamper 5 Pad Out Enable When set enables the Active Tamper 5 external pad." "0: Active Tamper 5 is disabled.,1: Active Tamper 5 is enabled." newline bitfld.long 0x0 19. "AT4_PAD_EN,Active Tamper 4 Pad Out Enable When set enables the Active Tamper 4 external pad." "0: Active Tamper 4 is disabled.,1: Active Tamper 4 is enabled." newline bitfld.long 0x0 18. "AT3_PAD_EN,Active Tamper 3 Pad Out Enable When set enables the Active Tamper 3 external pad." "0: Active Tamper 3 is disabled.,1: Active Tamper 3 is enabled" newline bitfld.long 0x0 17. "AT2_PAD_EN,Active Tamper 2 Pad Out Enable When set enables the Active Tamper 2 external pad." "0: Active Tamper 2 is disabled.,1: Active Tamper 2 is enabled." newline bitfld.long 0x0 16. "AT1_PAD_EN,Active Tamper 1 Pad Out Enable When set enables the Active Tamper 1 external pad." "0: Active Tamper 1 is disabled.,1: Active Tamper 1 is enabled." newline bitfld.long 0x0 4. "AT5_EN,Active Tamper 5 Enable When set enables the Active Tamper 5 LFSR." "0: Active Tamper 5 is disabled.,1: Active Tamper 5 is enabled." newline bitfld.long 0x0 3. "AT4_EN,Active Tamper 4 Enable When set enables the Active Tamper 4 LFSR." "0: Active Tamper 4 is disabled.,1: Active Tamper 4 is enabled." newline bitfld.long 0x0 2. "AT3_EN,Active Tamper 3 Enable When set enables the Active Tamper 3 LFSR." "0: Active Tamper 3 is disabled.,1: Active Tamper 3 is enabled." newline bitfld.long 0x0 1. "AT2_EN,Active Tamper 2 Enable When set enables the Active Tamper 2 LFSR." "0: Active Tamper 2 is disabled.,1: Active Tamper 2 is enabled." newline bitfld.long 0x0 0. "AT1_EN,Active Tamper 1 Enable When set enables the Active Tamper 1 LFSR." "0: Active Tamper 1 is disabled.,1: Active Tamper 1 is enabled." line.long 0x4 "LPATCLKR,SNVS_LP Active Tamper Clock Control Register" bitfld.long 0x4 16.--17. "AT5_CLK_CTL,Active Tamper 5 Clock Control 00: 16hz 01: 8hz 10: 4hz 11: 2hz" "0,1,2,3" newline bitfld.long 0x4 12.--13. "AT4_CLK_CTL,Active Tamper 4 Clock Control 00: 16hz 01: 8hz 10: 4hz 11: 2hz" "0,1,2,3" newline bitfld.long 0x4 8.--9. "AT3_CLK_CTL,Active Tamper 3 Clock Control 00: 16hz 01: 8hz 10: 4hz 11: 2hz" "0,1,2,3" newline bitfld.long 0x4 4.--5. "AT2_CLK_CTL,Active Tamper 2 Clock Control 00: 16hz 01: 8hz 10: 4hz 11: 2hz" "0,1,2,3" newline bitfld.long 0x4 0.--1. "AT1_CLK_CTL,Active Tamper 1 Clock Control 00: 16hz 01: 8hz 10: 4hz 11: 2hz" "0,1,2,3" line.long 0x8 "LPATRC1R,SNVS_LP Active Tamper Routing Control 1 Register" bitfld.long 0x8 28.--30. "ET8RCTL,External Tamper 8 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 24.--26. "ET7RCTL,External Tamper 7 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 20.--22. "ET6RCTL,External Tamper 6 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 16.--18. "ET5RCTL,External Tamper 5 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 12.--14. "ET4RCTL,External Tamper 4 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 8.--10. "ET3RCTL,External Tamper 3 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 4.--6. "ET2RCTL,External Tamper 2 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 0.--2. "ET1RCTL,External Tamper 1 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" line.long 0xC "LPATRC2R,SNVS_LP Active Tamper Routing Control 2 Register" bitfld.long 0xC 4.--6. "ET10RCTL,External Tamper 10 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 0.--2. "ET9RCTL,External Tamper 9 Routing Control Any undefined selection will be routed to passive" "0,1,2,3,4,5,6,7" repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x100)++0x3 line.long 0x0 "LPGPR[$1],SNVS_LP General Purpose Registers 0 .. 3" hexmask.long 0x0 0.--31. 1. "GPR,General Purpose Register When GPR_SL or GPR_HL bit is set the register cannot be programmed." repeat.end rgroup.long 0xBF8++0x7 line.long 0x0 "HPVIDR1,SNVS_HP Version ID Register 1" hexmask.long.word 0x0 16.--31. 1. "IP_ID,SNVS block ID" newline hexmask.long.byte 0x0 8.--15. 1. "MAJOR_REV,SNVS block major version number" newline hexmask.long.byte 0x0 0.--7. 1. "MINOR_REV,SNVS block minor version number" line.long 0x4 "HPVIDR2,SNVS_HP Version ID Register 2" hexmask.long.byte 0x4 24.--31. 1. "IP_ERA,IP Era 00h - Era 1 or 2 03h - Era 3 04h - Era 4 05h - Era 5 06h - Era 6" newline hexmask.long.byte 0x4 8.--15. 1. "ECO_REV,SNVS ECO Revision The engineering change order revision number for this release of SNVS." tree.end tree "SPDIF" base ad:0x40400000 group.long 0x0++0xF line.long 0x0 "SCR,SPDIF Configuration Register" bitfld.long 0x0 23. "RxFIFO_Ctrl,RxFIFO_Ctrl" "0: Normal operation,1: Always read zero from Rx data register" bitfld.long 0x0 22. "RxFIFO_Off_On,RxFIFO_Off_On" "0: SPDIF Rx FIFO is on,1: SPDIF Rx FIFO is off. Does not accept data from.." newline bitfld.long 0x0 21. "RxFIFO_Rst,RxFIFO_Rst" "0: Normal operation,1: Reset register to 1 sample remaining" bitfld.long 0x0 19.--20. "RxFIFOFull_Sel,RxFIFOFull_Sel" "0: Full interrupt if at least 1 sample in Rx left..,1: Full interrupt if at least 4 sample in Rx left..,2: Full interrupt if at least 8 sample in Rx left..,3: Full interrupt if at least 16 sample in Rx left.." newline bitfld.long 0x0 18. "RxAutoSync,RxAutoSync" "0: Rx FIFO auto sync off,1: RxFIFO auto sync on" bitfld.long 0x0 17. "TxAutoSync,TxAutoSync" "0: Tx FIFO auto sync off,1: Tx FIFO auto sync on" newline bitfld.long 0x0 15.--16. "TxFIFOEmpty_Sel,TxFIFOEmpty_Sel" "0: Empty interrupt if 0 sample in Tx left and right..,1: Empty interrupt if at most 4 sample in Tx left..,2: Empty interrupt if at most 8 sample in Tx left..,3: Empty interrupt if at most 12 sample in Tx left.." bitfld.long 0x0 13. "LOW_POWER,LOW_POWER" "0,1" newline bitfld.long 0x0 12. "soft_reset,soft_reset" "0,1" bitfld.long 0x0 10.--11. "TxFIFO_Ctrl,TxFIFO_Ctrl" "0: Send out digital zero on SPDIF Tx,1: Tx Normal operation,2: Reset to 1 sample remaining,?" newline bitfld.long 0x0 9. "DMA_Rx_En,DMA_Rx_En" "0,1" bitfld.long 0x0 8. "DMA_TX_En,DMA_TX_En" "0,1" newline bitfld.long 0x0 6.--7. "InputSrcSel,InputSrcSel" "0: SPDIF_IN,1: None,2: None,3: None" bitfld.long 0x0 5. "ValCtrl,ValCtrl" "0: Outgoing Validity always set,1: Outgoing Validity always clear" newline bitfld.long 0x0 2.--4. "TxSel,TxSel" "0: Off and output 0,1: Feed-through SPDIFIN,?,?,?,5: Tx Normal operation,?,?" bitfld.long 0x0 0.--1. "USrc_Sel,USrc_Sel" "0: No embedded U channel,1: U channel from SPDIF receive block (CD mode),?,3: U channel from on chip transmitter" line.long 0x4 "SRCD,CDText Control Register" bitfld.long 0x4 1. "USyncMode,USyncMode" "0: Non-CD data,1: CD user channel subcode" line.long 0x8 "SRPC,PhaseConfig Register" hexmask.long.byte 0x8 7.--10. 1. "ClkSrc_Sel,ClkSrc_Sel" rbitfld.long 0x8 6. "LOCK,LOCK" "0,1" newline bitfld.long 0x8 3.--5. "GainSel,GainSel" "0: 24*(2**10),1: 16*(2**10),2: 12*(2**10),3: 8*(2**10),4: 6*(2**10),5: 4*(2**10),6: 3*(2**10),?" line.long 0xC "SIE,InterruptEn Register" bitfld.long 0xC 20. "Lock,Lock" "0,1" bitfld.long 0xC 19. "TxUnOv,TxUnOv" "0,1" newline bitfld.long 0xC 18. "TxResyn,TxResyn" "0,1" bitfld.long 0xC 17. "CNew,CNew" "0,1" newline bitfld.long 0xC 16. "ValNoGood,ValNoGood" "0,1" bitfld.long 0xC 15. "SymErr,SymErr" "0,1" newline bitfld.long 0xC 14. "BitErr,BitErr" "0,1" bitfld.long 0xC 10. "URxFul,URxFul" "0,1" newline bitfld.long 0xC 9. "URxOv,URxOv" "0,1" bitfld.long 0xC 8. "QRxFul,QRxFul" "0,1" newline bitfld.long 0xC 7. "QRxOv,QRxOv" "0,1" bitfld.long 0xC 6. "UQSync,UQSync" "0,1" newline bitfld.long 0xC 5. "UQErr,UQErr" "0,1" bitfld.long 0xC 4. "RxFIFOUnOv,RxFIFOUnOv" "0,1" newline bitfld.long 0xC 3. "RxFIFOResyn,RxFIFOResyn" "0,1" bitfld.long 0xC 2. "LockLoss,LockLoss" "0,1" newline bitfld.long 0xC 1. "TxEm,TxEm" "0,1" bitfld.long 0xC 0. "RxFIFOFul,RxFIFOFul" "0,1" wgroup.long 0x10++0x3 line.long 0x0 "SIC,InterruptClear Register" bitfld.long 0x0 20. "Lock,Lock" "0,1" bitfld.long 0x0 19. "TxUnOv,TxUnOv" "0,1" newline bitfld.long 0x0 18. "TxResyn,TxResyn" "0,1" bitfld.long 0x0 17. "CNew,CNew" "0,1" newline bitfld.long 0x0 16. "ValNoGood,ValNoGood" "0,1" bitfld.long 0x0 15. "SymErr,SymErr" "0,1" newline bitfld.long 0x0 14. "BitErr,BitErr" "0,1" bitfld.long 0x0 9. "URxOv,URxOv" "0,1" newline bitfld.long 0x0 7. "QRxOv,QRxOv" "0,1" bitfld.long 0x0 6. "UQSync,UQSync" "0,1" newline bitfld.long 0x0 5. "UQErr,UQErr" "0,1" bitfld.long 0x0 4. "RxFIFOUnOv,RxFIFOUnOv" "0,1" newline bitfld.long 0x0 3. "RxFIFOResyn,RxFIFOResyn" "0,1" bitfld.long 0x0 2. "LockLoss,LockLoss" "0,1" rgroup.long 0x10++0x1B line.long 0x0 "SIS,InterruptStat Register" bitfld.long 0x0 20. "Lock,Lock" "0,1" bitfld.long 0x0 19. "TxUnOv,TxUnOv" "0,1" newline bitfld.long 0x0 18. "TxResyn,TxResyn" "0,1" bitfld.long 0x0 17. "CNew,CNew" "0,1" newline bitfld.long 0x0 16. "ValNoGood,ValNoGood" "0,1" bitfld.long 0x0 15. "SymErr,SymErr" "0,1" newline bitfld.long 0x0 14. "BitErr,BitErr" "0,1" bitfld.long 0x0 10. "URxFul,URxFul" "0,1" newline bitfld.long 0x0 9. "URxOv,URxOv" "0,1" bitfld.long 0x0 8. "QRxFul,QRxFul" "0,1" newline bitfld.long 0x0 7. "QRxOv,QRxOv" "0,1" bitfld.long 0x0 6. "UQSync,UQSync" "0,1" newline bitfld.long 0x0 5. "UQErr,UQErr" "0,1" bitfld.long 0x0 4. "RxFIFOUnOv,RxFIFOUnOv" "0,1" newline bitfld.long 0x0 3. "RxFIFOResyn,RxFIFOResyn" "0,1" bitfld.long 0x0 2. "LockLoss,LockLoss" "0,1" newline bitfld.long 0x0 1. "TxEm,TxEm" "0,1" bitfld.long 0x0 0. "RxFIFOFul,RxFIFOFul" "0,1" line.long 0x4 "SRL,SPDIFRxLeft Register" hexmask.long.tbyte 0x4 0.--23. 1. "RxDataLeft,RxDataLeft" line.long 0x8 "SRR,SPDIFRxRight Register" hexmask.long.tbyte 0x8 0.--23. 1. "RxDataRight,RxDataRight" line.long 0xC "SRCSH,SPDIFRxCChannel_h Register" hexmask.long.tbyte 0xC 0.--23. 1. "RxCChannel_h,RxCChannel_h" line.long 0x10 "SRCSL,SPDIFRxCChannel_l Register" hexmask.long.tbyte 0x10 0.--23. 1. "RxCChannel_l,RxCChannel_l" line.long 0x14 "SRU,UchannelRx Register" hexmask.long.tbyte 0x14 0.--23. 1. "RxUChannel,RxUChannel" line.long 0x18 "SRQ,QchannelRx Register" hexmask.long.tbyte 0x18 0.--23. 1. "RxQChannel,RxQChannel" wgroup.long 0x2C++0x7 line.long 0x0 "STL,SPDIFTxLeft Register" hexmask.long.tbyte 0x0 0.--23. 1. "TxDataLeft,TxDataLeft" line.long 0x4 "STR,SPDIFTxRight Register" hexmask.long.tbyte 0x4 0.--23. 1. "TxDataRight,TxDataRight" group.long 0x34++0x7 line.long 0x0 "STCSCH,SPDIFTxCChannelCons_h Register" hexmask.long.tbyte 0x0 0.--23. 1. "TxCChannelCons_h,TxCChannelCons_h" line.long 0x4 "STCSCL,SPDIFTxCChannelCons_l Register" hexmask.long.tbyte 0x4 0.--23. 1. "TxCChannelCons_l,TxCChannelCons_l" rgroup.long 0x44++0x3 line.long 0x0 "SRFM,FreqMeas Register" hexmask.long.tbyte 0x0 0.--23. 1. "FreqMeas,FreqMeas" group.long 0x50++0x3 line.long 0x0 "STC,SPDIFTxClk Register" hexmask.long.word 0x0 11.--19. 1. "SYSCLK_DF,SYSCLK_DF" bitfld.long 0x0 8.--10. "TxClk_Source,TxClk_Source" "0: REF_CLK_32K input (XTALOSC 32 kHz clock),1: tx_clk input (from SPDIF0_CLK_ROOT. See clock..,?,3: SPDIF_EXT_CLK from pads,?,5: ipg_clk input (frequency divided),?,?" newline bitfld.long 0x0 7. "tx_all_clk_en,tx_all_clk_en" "0: disable transfer clock.,1: enable transfer clock." hexmask.long.byte 0x0 0.--6. 1. "TxClk_DF,TxClk_DF" tree.end tree "SRAM" base ad:0x40C9C000 group.long 0x3000++0x3 line.long 0x0 "CTRL,Control Register" hexmask.long.byte 0x0 16.--23. 1. "LOCK_BIT,Lock bits" bitfld.long 0x0 7. "TAMPER_PWR_OFF_EN,Turn off power on tamper event (with lock)" "0: Disable the turn off function when tamper is..,1: Turn off power for all secure RAM banks when.." newline bitfld.long 0x0 6. "TAMPER_BLOCK_EN,Tamper Block Enable (with lock)" "0: Allow R/W access to secure RAM when tamper is..,1: Block R/W access to secure RAM when tamper is.." hexmask.long.byte 0x0 2.--5. 1. "PWR_EN,Power Enable (with lock)" newline bitfld.long 0x0 1. "RAM_WR_EN,RAM Write Enable (with lock)" "0: Disable write access,1: Enable write access" bitfld.long 0x0 0. "RAM_RD_EN,RAM Read Enable (with lock)" "0: Disable read access,1: Enable read access" tree.end tree "SRC" base ad:0x40C04000 group.long 0x0++0x7 line.long 0x0 "SCR,SRC Control Register" bitfld.long 0x0 1. "BT_RELEASE_M7,cm7 core reset will be held until boot core write this bit to 1 to release it." "0: cm7 core reset is asserted,1: cm7 core reset is released" newline bitfld.long 0x0 0. "BT_RELEASE_M4,cm4 core reset will be held until boot core write this bit to 1 to release it." "0: cm4 core reset is asserted,1: cm4 core reset is released" line.long 0x4 "SRMR,SRC Reset Mode Register" bitfld.long 0x4 20.--21. "OVERVOLT_RESET_MODE,Jtag SW reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 18.--19. "JTAGSW_RESET_MODE,Jtag SW reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 16.--17. "CSU_RESET_MODE,CSU reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 14.--15. "TEMPSENSE_RESET_MODE,Tempsense reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 12.--13. "M7REQ_RESET_MODE,M7 request reset configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 10.--11. "M4REQ_RESET_MODE,M4 request reset configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 8.--9. "M7LOCKUP_RESET_MODE,M7 core lockup reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 6.--7. "M4LOCKUP_RESET_MODE,M4 core lockup reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 4.--5. "WDOG4_RESET_MODE,Wdog4 reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 2.--3. "WDOG3_RESET_MODE,Wdog3 reset mode configuration" "0: reset system,?,?,3: do not reset anything" newline bitfld.long 0x4 0.--1. "WDOG_RESET_MODE,Wdog reset mode configuration" "0: reset system,?,?,3: do not reset anything" rgroup.long 0x8++0x7 line.long 0x0 "SBMR1,SRC Boot Mode Register 1" hexmask.long.byte 0x0 24.--31. 1. "BOOT_CFG4,Please see fusemap." newline hexmask.long.byte 0x0 16.--23. 1. "BOOT_CFG3,Please see fusemap." newline hexmask.long.byte 0x0 8.--15. 1. "BOOT_CFG2,Please see fusemap." newline hexmask.long.byte 0x0 0.--7. 1. "BOOT_CFG1,Please see fusemap." line.long 0x4 "SBMR2,SRC Boot Mode Register 2" bitfld.long 0x4 24.--25. "BMOD,BMOD[1:0] shows the latched state of the BOOT_MODE1 and BOOT_MODE0 signals on the rising edge of POR_B" "0,1,2,3" newline bitfld.long 0x4 4. "BT_FUSE_SEL,BT_FUSE_SEL shows the state of the BT_FUSE_SEL fuse" "0,1" newline bitfld.long 0x4 0.--1. "SEC_CONFIG,SECONFIG[1] shows the state of the SECONFIG[1] fuse" "0,1,2,3" group.long 0x10++0x3 line.long 0x0 "SRSR,SRC Reset Status Register" eventfld.long 0x0 30. "CDOG_RST_M4,Indicates a reset has been caused by CDOG reset." "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 29. "OVERVOLT_RST_M4,Indicates a reset has been caused by power suppy voltage over the highest permitted level." "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 28. "M7_LOCKUP_M4,Indicates a reset has been caused by M7 CPU lockup or software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register of the ARM core" "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 27. "M7_REQUEST_M4,Indicates whether reset was the result of m7 reset request." "0: Reset is not a result of m7 reset request.,1: Reset is a result of m7 reset request." newline eventfld.long 0x0 26. "TEMPSENSE_RST_B_M4,Temper Sensor software reset" "0: Reset is not a result of software reset from..,1: Reset is a result of software reset from.." newline eventfld.long 0x0 25. "WDOG4_RST_B_M4,IC Watchdog4 Time-out reset" "0: Reset is not a result of the watchdog4 time-out..,1: Reset is a result of the watchdog4 time-out event." newline eventfld.long 0x0 24. "WDOG3_RST_B_M4,IC Watchdog3 Time-out reset" "0: Reset is not a result of the watchdog3 time-out..,1: Reset is a result of the watchdog3 time-out event." newline eventfld.long 0x0 23. "JTAG_SW_RST_M4,JTAG software reset. Indicates whether the reset was the result of software reset from JTAG." "0: Reset is not a result of software reset from JTAG.,1: Reset is a result of software reset from JTAG." newline eventfld.long 0x0 22. "JTAG_RST_B_M4,HIGH - Z JTAG reset. Indicates whether the reset was the result of HIGH-Z reset from JTAG." "0: Reset is not a result of HIGH-Z reset from JTAG.,1: Reset is a result of HIGH-Z reset from JTAG." newline eventfld.long 0x0 21. "WDOG_RST_B_M4,IC Watchdog Time-out reset" "0: Reset is not a result of the watchdog time-out..,1: Reset is a result of the watchdog time-out event." newline eventfld.long 0x0 20. "IPP_USER_RESET_B_M4,Indicates whether the reset was the result of the ipp_user_reset_b qualified reset." "0: Reset is not a result of the ipp_user_reset_b..,1: Reset is a result of the ipp_user_reset_b.." newline eventfld.long 0x0 19. "CSU_RESET_B_M4,Indicates whether the reset was the result of the csu_reset_b input." "0: Reset is not a result of the csu_reset_b event.,1: Reset is a result of the csu_reset_b event." newline eventfld.long 0x0 18. "M4_LOCKUP_M4,Indicates a reset has been caused by M4 CPU lockup or software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register of the ARM core" "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 17. "M4_REQUEST_M4,Indicates whether reset was the result of m4 reset request" "0: Reset is not a result of m4 reset request.,1: Reset is a result of m4 reset request." newline eventfld.long 0x0 16. "IPP_RESET_B_M4,Indicates whether reset was the result of ipp_reset_b pin (Power-up sequence)" "0: Reset is not a result of ipp_reset_b pin.,1: Reset is a result of ipp_reset_b pin." newline eventfld.long 0x0 14. "CDOG_RST_M7,Indicates a reset has been caused by CDOG reset." "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 13. "OVERVOLT_RST_M7,Indicates a reset has been caused by power suppy voltage over the highest permitted level." "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 12. "M4_LOCKUP_M7,Indicates a reset has been caused by M4 CPU lockup or software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register of the ARM core" "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 11. "M4_REQUEST_M7,Indicates whether reset was the result of m4 reset request." "0: Reset is not a result of m4 reset request.,1: Reset is a result of m4 reset request." newline eventfld.long 0x0 10. "TEMPSENSE_RST_B_M7,Temper Sensor software reset" "0: Reset is not a result of software reset from..,1: Reset is a result of software reset from.." newline eventfld.long 0x0 9. "WDOG4_RST_B_M7,IC Watchdog4 Time-out reset" "0: Reset is not a result of the watchdog4 time-out..,1: Reset is a result of the watchdog4 time-out event." newline eventfld.long 0x0 8. "WDOG3_RST_B_M7,IC Watchdog3 Time-out reset" "0: Reset is not a result of the watchdog3 time-out..,1: Reset is a result of the watchdog3 time-out event." newline eventfld.long 0x0 7. "JTAG_SW_RST_M7,JTAG software reset. Indicates whether the reset was the result of software reset from JTAG." "0: Reset is not a result of software reset from JTAG.,1: Reset is a result of software reset from JTAG." newline eventfld.long 0x0 6. "JTAG_RST_B_M7,HIGH - Z JTAG reset. Indicates whether the reset was the result of HIGH-Z reset from JTAG." "0: Reset is not a result of HIGH-Z reset from JTAG.,1: Reset is a result of HIGH-Z reset from JTAG." newline eventfld.long 0x0 5. "WDOG_RST_B_M7,IC Watchdog Time-out reset" "0: Reset is not a result of the watchdog time-out..,1: Reset is a result of the watchdog time-out event." newline eventfld.long 0x0 4. "IPP_USER_RESET_B_M7,Indicates whether the reset was the result of the ipp_user_reset_b qualified reset." "0: Reset is not a result of the ipp_user_reset_b..,1: Reset is a result of the ipp_user_reset_b.." newline eventfld.long 0x0 3. "CSU_RESET_B_M7,Indicates whether the reset was the result of the csu_reset_b input." "0: Reset is not a result of the csu_reset_b event.,1: Reset is a result of the csu_reset_b event." newline eventfld.long 0x0 2. "M7_LOCKUP_M7,Indicates a reset has been caused by M7 CPU lockup or software setting of SYSRESETREQ bit in Application Interrupt and Reset Control Register of the ARM core" "0: Reset is not a result of the mentioned case.,1: Reset is a result of the mentioned case." newline eventfld.long 0x0 1. "M7_REQUEST_M7,Indicates whether reset was the result of m7 reset request" "0: Reset is not a result of m7 reset request.,1: Reset is a result of m7 reset request." newline eventfld.long 0x0 0. "IPP_RESET_B_M7,Indicates whether reset was the result of ipp_reset_b pin (Power-up sequence)" "0: Reset is not a result of ipp_reset_b pin.,1: Reset is a result of ipp_reset_b pin." repeat 20. (increment 0x0 0x1)(increment 0x0 0x4) group.long ($2+0x14)++0x3 line.long 0x0 "GPR$1,SRC General Purpose Register" hexmask.long 0x0 0.--31. 1. "GPR,General Purpose Register." repeat.end group.long 0x200++0x13 line.long 0x0 "AUTHEN_MEGA,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_MEGA,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_MEGA,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_MEGA,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_MEGA,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x220++0x13 line.long 0x0 "AUTHEN_DISPLAY,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_DISPLAY,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_DISPLAY,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_DISPLAY,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_DISPLAY,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x240++0x13 line.long 0x0 "AUTHEN_WAKEUP,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_WAKEUP,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_WAKEUP,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_WAKEUP,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_WAKEUP,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x280++0x13 line.long 0x0 "AUTHEN_M4CORE,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_M4CORE,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_M4CORE,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_M4CORE,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_M4CORE,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x2A0++0x13 line.long 0x0 "AUTHEN_M7CORE,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_M7CORE,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_M7CORE,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_M7CORE,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_M7CORE,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x2C0++0x13 line.long 0x0 "AUTHEN_M4DEBUG,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_M4DEBUG,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_M4DEBUG,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_M4DEBUG,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_M4DEBUG,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x2E0++0x13 line.long 0x0 "AUTHEN_M7DEBUG,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_M7DEBUG,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_M7DEBUG,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_M7DEBUG,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_M7DEBUG,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x300++0x13 line.long 0x0 "AUTHEN_USBPHY1,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_USBPHY1,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_USBPHY1,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_USBPHY1,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_USBPHY1,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" group.long 0x320++0x13 line.long 0x0 "AUTHEN_USBPHY2,Slice Authentication Register" bitfld.long 0x0 31. "LOCK_SETTING,Lock NONSECURE and USER" "0,1" newline bitfld.long 0x0 25. "NONSECURE,Allow non-secure mode access" "0,1" newline bitfld.long 0x0 24. "USER,Allow user mode access" "0,1" newline bitfld.long 0x0 23. "LOCK_LIST,White list lock" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "WHITE_LIST,Domain ID white list" newline bitfld.long 0x0 15. "LOCK_ASSIGN,Assign list lock" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "ASSIGN_LIST,when this bitfield set to 1 reset of slice would be subject to corresponding core status transition" newline bitfld.long 0x0 7. "LOCK_MODE,Domain/Setpoint mode lock" "0,1" newline bitfld.long 0x0 1. "SETPOINT_MODE,Control whether reset slice is in Setpoint mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by.." newline bitfld.long 0x0 0. "DOMAIN_MODE,Control whether reset slice is in domain mode" "0: slice hardware reset will NOT be triggered by..,1: slice hardware reset will be triggered by CPU.." line.long 0x4 "CTRL_USBPHY2,Slice Control Register" bitfld.long 0x4 0. "SW_RESET,This is a self clearing bit" "0: do not assert slice software reset,1: assert slice software reset" line.long 0x8 "SETPOINT_USBPHY2,Slice Setpoint Config Register" bitfld.long 0x8 15. "SETPOINT15,SETPOINT15" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 14. "SETPOINT14,SETPOINT14" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 13. "SETPOINT13,SETPOINT13" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 12. "SETPOINT12,SETPOINT12" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 11. "SETPOINT11,SETPOINT11" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 10. "SETPOINT10,SETPOINT10" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 9. "SETPOINT9,SETPOINT9" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 8. "SETPOINT8,SETPOINT8" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 7. "SETPOINT7,SETPOINT7" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 6. "SETPOINT6,SETPOINT6" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 5. "SETPOINT5,SETPOINT5" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 4. "SETPOINT4,SETPOINT4" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 3. "SETPOINT3,SETPOINT3" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 2. "SETPOINT2,SETPOINT2" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 1. "SETPOINT1,SETPOINT1" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." newline bitfld.long 0x8 0. "SETPOINT0,SETPOINT0" "0: Slice reset will be de-asserted when system in..,1: Slice reset will be asserted when system in.." line.long 0xC "DOMAIN_USBPHY2,Slice Domain Config Register" bitfld.long 0xC 7. "CPU1_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in.." newline bitfld.long 0xC 6. "CPU1_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in STOP.." newline bitfld.long 0xC 5. "CPU1_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU1 in..,1: Slice reset will be asserted when CPU1 in WAIT.." newline bitfld.long 0xC 4. "CPU1_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU1 in RUN..,1: Slice reset will be asserted when CPU1 in RUN mode" newline bitfld.long 0xC 3. "CPU0_SUSP,CPU mode setting for SUSPEND" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in.." newline bitfld.long 0xC 2. "CPU0_STOP,CPU mode setting for STOP" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in STOP.." newline bitfld.long 0xC 1. "CPU0_WAIT,CPU mode setting for WAIT" "0: Slice reset will be de-asserted when CPU0 in..,1: Slice reset will be asserted when CPU0 in WAIT.." newline bitfld.long 0xC 0. "CPU0_RUN,CPU mode setting for RUN" "0: Slice reset will be de-asserted when CPU0 in RUN..,1: Slice reset will be asserted when CPU0 in RUN mode" line.long 0x10 "STAT_USBPHY2,Slice Status Register" eventfld.long 0x10 3. "RST_BY_SW,This bit indicate if the reset is caused by setting SW_RESET bit." "0: the reset is not caused by software setting,1: the reset is caused by software setting" newline eventfld.long 0x10 2. "RST_BY_HW,This bit indicate if the reset is caused by the power mode transfer." "0: the reset is not caused by the power mode transfer,1: the reset is caused by the power mode transfer" newline rbitfld.long 0x10 0. "UNDER_RST,This is a Read Only bit. It indicate if the reset is in process." "0: the reset is finished,1: the reset is in process" tree.end tree "SSARC" base ad:0x0 tree "SSARC_HP" base ad:0x40CB4000 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CB4000 ad:0x40CB4010 ad:0x40CB4020 ad:0x40CB4030 ad:0x40CB4040 ad:0x40CB4050 ad:0x40CB4060 ad:0x40CB4070 ad:0x40CB4080 ad:0x40CB4090 ad:0x40CB40A0 ad:0x40CB40B0 ad:0x40CB40C0 ad:0x40CB40D0 ad:0x40CB40E0 ad:0x40CB40F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CB4100 ad:0x40CB4110 ad:0x40CB4120 ad:0x40CB4130 ad:0x40CB4140 ad:0x40CB4150 ad:0x40CB4160 ad:0x40CB4170 ad:0x40CB4180 ad:0x40CB4190 ad:0x40CB41A0 ad:0x40CB41B0 ad:0x40CB41C0 ad:0x40CB41D0 ad:0x40CB41E0 ad:0x40CB41F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list ad:0x40CB4200 ad:0x40CB4210 ad:0x40CB4220 ad:0x40CB4230 ad:0x40CB4240 ad:0x40CB4250 ad:0x40CB4260 ad:0x40CB4270 ad:0x40CB4280 ad:0x40CB4290 ad:0x40CB42A0 ad:0x40CB42B0 ad:0x40CB42C0 ad:0x40CB42D0 ad:0x40CB42E0 ad:0x40CB42F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list ad:0x40CB4300 ad:0x40CB4310 ad:0x40CB4320 ad:0x40CB4330 ad:0x40CB4340 ad:0x40CB4350 ad:0x40CB4360 ad:0x40CB4370 ad:0x40CB4380 ad:0x40CB4390 ad:0x40CB43A0 ad:0x40CB43B0 ad:0x40CB43C0 ad:0x40CB43D0 ad:0x40CB43E0 ad:0x40CB43F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list ad:0x40CB4400 ad:0x40CB4410 ad:0x40CB4420 ad:0x40CB4430 ad:0x40CB4440 ad:0x40CB4450 ad:0x40CB4460 ad:0x40CB4470 ad:0x40CB4480 ad:0x40CB4490 ad:0x40CB44A0 ad:0x40CB44B0 ad:0x40CB44C0 ad:0x40CB44D0 ad:0x40CB44E0 ad:0x40CB44F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list ad:0x40CB4500 ad:0x40CB4510 ad:0x40CB4520 ad:0x40CB4530 ad:0x40CB4540 ad:0x40CB4550 ad:0x40CB4560 ad:0x40CB4570 ad:0x40CB4580 ad:0x40CB4590 ad:0x40CB45A0 ad:0x40CB45B0 ad:0x40CB45C0 ad:0x40CB45D0 ad:0x40CB45E0 ad:0x40CB45F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list ad:0x40CB4600 ad:0x40CB4610 ad:0x40CB4620 ad:0x40CB4630 ad:0x40CB4640 ad:0x40CB4650 ad:0x40CB4660 ad:0x40CB4670 ad:0x40CB4680 ad:0x40CB4690 ad:0x40CB46A0 ad:0x40CB46B0 ad:0x40CB46C0 ad:0x40CB46D0 ad:0x40CB46E0 ad:0x40CB46F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list ad:0x40CB4700 ad:0x40CB4710 ad:0x40CB4720 ad:0x40CB4730 ad:0x40CB4740 ad:0x40CB4750 ad:0x40CB4760 ad:0x40CB4770 ad:0x40CB4780 ad:0x40CB4790 ad:0x40CB47A0 ad:0x40CB47B0 ad:0x40CB47C0 ad:0x40CB47D0 ad:0x40CB47E0 ad:0x40CB47F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C 0x8D 0x8E 0x8F)(list ad:0x40CB4800 ad:0x40CB4810 ad:0x40CB4820 ad:0x40CB4830 ad:0x40CB4840 ad:0x40CB4850 ad:0x40CB4860 ad:0x40CB4870 ad:0x40CB4880 ad:0x40CB4890 ad:0x40CB48A0 ad:0x40CB48B0 ad:0x40CB48C0 ad:0x40CB48D0 ad:0x40CB48E0 ad:0x40CB48F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0x9E 0x9F)(list ad:0x40CB4900 ad:0x40CB4910 ad:0x40CB4920 ad:0x40CB4930 ad:0x40CB4940 ad:0x40CB4950 ad:0x40CB4960 ad:0x40CB4970 ad:0x40CB4980 ad:0x40CB4990 ad:0x40CB49A0 ad:0x40CB49B0 ad:0x40CB49C0 ad:0x40CB49D0 ad:0x40CB49E0 ad:0x40CB49F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF)(list ad:0x40CB4A00 ad:0x40CB4A10 ad:0x40CB4A20 ad:0x40CB4A30 ad:0x40CB4A40 ad:0x40CB4A50 ad:0x40CB4A60 ad:0x40CB4A70 ad:0x40CB4A80 ad:0x40CB4A90 ad:0x40CB4AA0 ad:0x40CB4AB0 ad:0x40CB4AC0 ad:0x40CB4AD0 ad:0x40CB4AE0 ad:0x40CB4AF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF)(list ad:0x40CB4B00 ad:0x40CB4B10 ad:0x40CB4B20 ad:0x40CB4B30 ad:0x40CB4B40 ad:0x40CB4B50 ad:0x40CB4B60 ad:0x40CB4B70 ad:0x40CB4B80 ad:0x40CB4B90 ad:0x40CB4BA0 ad:0x40CB4BB0 ad:0x40CB4BC0 ad:0x40CB4BD0 ad:0x40CB4BE0 ad:0x40CB4BF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF)(list ad:0x40CB4C00 ad:0x40CB4C10 ad:0x40CB4C20 ad:0x40CB4C30 ad:0x40CB4C40 ad:0x40CB4C50 ad:0x40CB4C60 ad:0x40CB4C70 ad:0x40CB4C80 ad:0x40CB4C90 ad:0x40CB4CA0 ad:0x40CB4CB0 ad:0x40CB4CC0 ad:0x40CB4CD0 ad:0x40CB4CE0 ad:0x40CB4CF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC 0xDD 0xDE 0xDF)(list ad:0x40CB4D00 ad:0x40CB4D10 ad:0x40CB4D20 ad:0x40CB4D30 ad:0x40CB4D40 ad:0x40CB4D50 ad:0x40CB4D60 ad:0x40CB4D70 ad:0x40CB4D80 ad:0x40CB4D90 ad:0x40CB4DA0 ad:0x40CB4DB0 ad:0x40CB4DC0 ad:0x40CB4DD0 ad:0x40CB4DE0 ad:0x40CB4DF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xE0 0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE 0xEF)(list ad:0x40CB4E00 ad:0x40CB4E10 ad:0x40CB4E20 ad:0x40CB4E30 ad:0x40CB4E40 ad:0x40CB4E50 ad:0x40CB4E60 ad:0x40CB4E70 ad:0x40CB4E80 ad:0x40CB4E90 ad:0x40CB4EA0 ad:0x40CB4EB0 ad:0x40CB4EC0 ad:0x40CB4ED0 ad:0x40CB4EE0 ad:0x40CB4EF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0xF0 0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 0xF7 0xF8 0xF9 0xFA 0xFB 0xFC 0xFD 0xFE 0xFF)(list ad:0x40CB4F00 ad:0x40CB4F10 ad:0x40CB4F20 ad:0x40CB4F30 ad:0x40CB4F40 ad:0x40CB4F50 ad:0x40CB4F60 ad:0x40CB4F70 ad:0x40CB4F80 ad:0x40CB4F90 ad:0x40CB4FA0 ad:0x40CB4FB0 ad:0x40CB4FC0 ad:0x40CB4FD0 ad:0x40CB4FE0 ad:0x40CB4FF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x100 0x101 0x102 0x103 0x104 0x105 0x106 0x107 0x108 0x109 0x10A 0x10B 0x10C 0x10D 0x10E 0x10F)(list ad:0x40CB5000 ad:0x40CB5010 ad:0x40CB5020 ad:0x40CB5030 ad:0x40CB5040 ad:0x40CB5050 ad:0x40CB5060 ad:0x40CB5070 ad:0x40CB5080 ad:0x40CB5090 ad:0x40CB50A0 ad:0x40CB50B0 ad:0x40CB50C0 ad:0x40CB50D0 ad:0x40CB50E0 ad:0x40CB50F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x110 0x111 0x112 0x113 0x114 0x115 0x116 0x117 0x118 0x119 0x11A 0x11B 0x11C 0x11D 0x11E 0x11F)(list ad:0x40CB5100 ad:0x40CB5110 ad:0x40CB5120 ad:0x40CB5130 ad:0x40CB5140 ad:0x40CB5150 ad:0x40CB5160 ad:0x40CB5170 ad:0x40CB5180 ad:0x40CB5190 ad:0x40CB51A0 ad:0x40CB51B0 ad:0x40CB51C0 ad:0x40CB51D0 ad:0x40CB51E0 ad:0x40CB51F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x120 0x121 0x122 0x123 0x124 0x125 0x126 0x127 0x128 0x129 0x12A 0x12B 0x12C 0x12D 0x12E 0x12F)(list ad:0x40CB5200 ad:0x40CB5210 ad:0x40CB5220 ad:0x40CB5230 ad:0x40CB5240 ad:0x40CB5250 ad:0x40CB5260 ad:0x40CB5270 ad:0x40CB5280 ad:0x40CB5290 ad:0x40CB52A0 ad:0x40CB52B0 ad:0x40CB52C0 ad:0x40CB52D0 ad:0x40CB52E0 ad:0x40CB52F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x130 0x131 0x132 0x133 0x134 0x135 0x136 0x137 0x138 0x139 0x13A 0x13B 0x13C 0x13D 0x13E 0x13F)(list ad:0x40CB5300 ad:0x40CB5310 ad:0x40CB5320 ad:0x40CB5330 ad:0x40CB5340 ad:0x40CB5350 ad:0x40CB5360 ad:0x40CB5370 ad:0x40CB5380 ad:0x40CB5390 ad:0x40CB53A0 ad:0x40CB53B0 ad:0x40CB53C0 ad:0x40CB53D0 ad:0x40CB53E0 ad:0x40CB53F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x140 0x141 0x142 0x143 0x144 0x145 0x146 0x147 0x148 0x149 0x14A 0x14B 0x14C 0x14D 0x14E 0x14F)(list ad:0x40CB5400 ad:0x40CB5410 ad:0x40CB5420 ad:0x40CB5430 ad:0x40CB5440 ad:0x40CB5450 ad:0x40CB5460 ad:0x40CB5470 ad:0x40CB5480 ad:0x40CB5490 ad:0x40CB54A0 ad:0x40CB54B0 ad:0x40CB54C0 ad:0x40CB54D0 ad:0x40CB54E0 ad:0x40CB54F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x150 0x151 0x152 0x153 0x154 0x155 0x156 0x157 0x158 0x159 0x15A 0x15B 0x15C 0x15D 0x15E 0x15F)(list ad:0x40CB5500 ad:0x40CB5510 ad:0x40CB5520 ad:0x40CB5530 ad:0x40CB5540 ad:0x40CB5550 ad:0x40CB5560 ad:0x40CB5570 ad:0x40CB5580 ad:0x40CB5590 ad:0x40CB55A0 ad:0x40CB55B0 ad:0x40CB55C0 ad:0x40CB55D0 ad:0x40CB55E0 ad:0x40CB55F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x160 0x161 0x162 0x163 0x164 0x165 0x166 0x167 0x168 0x169 0x16A 0x16B 0x16C 0x16D 0x16E 0x16F)(list ad:0x40CB5600 ad:0x40CB5610 ad:0x40CB5620 ad:0x40CB5630 ad:0x40CB5640 ad:0x40CB5650 ad:0x40CB5660 ad:0x40CB5670 ad:0x40CB5680 ad:0x40CB5690 ad:0x40CB56A0 ad:0x40CB56B0 ad:0x40CB56C0 ad:0x40CB56D0 ad:0x40CB56E0 ad:0x40CB56F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x170 0x171 0x172 0x173 0x174 0x175 0x176 0x177 0x178 0x179 0x17A 0x17B 0x17C 0x17D 0x17E 0x17F)(list ad:0x40CB5700 ad:0x40CB5710 ad:0x40CB5720 ad:0x40CB5730 ad:0x40CB5740 ad:0x40CB5750 ad:0x40CB5760 ad:0x40CB5770 ad:0x40CB5780 ad:0x40CB5790 ad:0x40CB57A0 ad:0x40CB57B0 ad:0x40CB57C0 ad:0x40CB57D0 ad:0x40CB57E0 ad:0x40CB57F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x180 0x181 0x182 0x183 0x184 0x185 0x186 0x187 0x188 0x189 0x18A 0x18B 0x18C 0x18D 0x18E 0x18F)(list ad:0x40CB5800 ad:0x40CB5810 ad:0x40CB5820 ad:0x40CB5830 ad:0x40CB5840 ad:0x40CB5850 ad:0x40CB5860 ad:0x40CB5870 ad:0x40CB5880 ad:0x40CB5890 ad:0x40CB58A0 ad:0x40CB58B0 ad:0x40CB58C0 ad:0x40CB58D0 ad:0x40CB58E0 ad:0x40CB58F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x190 0x191 0x192 0x193 0x194 0x195 0x196 0x197 0x198 0x199 0x19A 0x19B 0x19C 0x19D 0x19E 0x19F)(list ad:0x40CB5900 ad:0x40CB5910 ad:0x40CB5920 ad:0x40CB5930 ad:0x40CB5940 ad:0x40CB5950 ad:0x40CB5960 ad:0x40CB5970 ad:0x40CB5980 ad:0x40CB5990 ad:0x40CB59A0 ad:0x40CB59B0 ad:0x40CB59C0 ad:0x40CB59D0 ad:0x40CB59E0 ad:0x40CB59F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1A0 0x1A1 0x1A2 0x1A3 0x1A4 0x1A5 0x1A6 0x1A7 0x1A8 0x1A9 0x1AA 0x1AB 0x1AC 0x1AD 0x1AE 0x1AF)(list ad:0x40CB5A00 ad:0x40CB5A10 ad:0x40CB5A20 ad:0x40CB5A30 ad:0x40CB5A40 ad:0x40CB5A50 ad:0x40CB5A60 ad:0x40CB5A70 ad:0x40CB5A80 ad:0x40CB5A90 ad:0x40CB5AA0 ad:0x40CB5AB0 ad:0x40CB5AC0 ad:0x40CB5AD0 ad:0x40CB5AE0 ad:0x40CB5AF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1B0 0x1B1 0x1B2 0x1B3 0x1B4 0x1B5 0x1B6 0x1B7 0x1B8 0x1B9 0x1BA 0x1BB 0x1BC 0x1BD 0x1BE 0x1BF)(list ad:0x40CB5B00 ad:0x40CB5B10 ad:0x40CB5B20 ad:0x40CB5B30 ad:0x40CB5B40 ad:0x40CB5B50 ad:0x40CB5B60 ad:0x40CB5B70 ad:0x40CB5B80 ad:0x40CB5B90 ad:0x40CB5BA0 ad:0x40CB5BB0 ad:0x40CB5BC0 ad:0x40CB5BD0 ad:0x40CB5BE0 ad:0x40CB5BF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1C0 0x1C1 0x1C2 0x1C3 0x1C4 0x1C5 0x1C6 0x1C7 0x1C8 0x1C9 0x1CA 0x1CB 0x1CC 0x1CD 0x1CE 0x1CF)(list ad:0x40CB5C00 ad:0x40CB5C10 ad:0x40CB5C20 ad:0x40CB5C30 ad:0x40CB5C40 ad:0x40CB5C50 ad:0x40CB5C60 ad:0x40CB5C70 ad:0x40CB5C80 ad:0x40CB5C90 ad:0x40CB5CA0 ad:0x40CB5CB0 ad:0x40CB5CC0 ad:0x40CB5CD0 ad:0x40CB5CE0 ad:0x40CB5CF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1D0 0x1D1 0x1D2 0x1D3 0x1D4 0x1D5 0x1D6 0x1D7 0x1D8 0x1D9 0x1DA 0x1DB 0x1DC 0x1DD 0x1DE 0x1DF)(list ad:0x40CB5D00 ad:0x40CB5D10 ad:0x40CB5D20 ad:0x40CB5D30 ad:0x40CB5D40 ad:0x40CB5D50 ad:0x40CB5D60 ad:0x40CB5D70 ad:0x40CB5D80 ad:0x40CB5D90 ad:0x40CB5DA0 ad:0x40CB5DB0 ad:0x40CB5DC0 ad:0x40CB5DD0 ad:0x40CB5DE0 ad:0x40CB5DF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1E0 0x1E1 0x1E2 0x1E3 0x1E4 0x1E5 0x1E6 0x1E7 0x1E8 0x1E9 0x1EA 0x1EB 0x1EC 0x1ED 0x1EE 0x1EF)(list ad:0x40CB5E00 ad:0x40CB5E10 ad:0x40CB5E20 ad:0x40CB5E30 ad:0x40CB5E40 ad:0x40CB5E50 ad:0x40CB5E60 ad:0x40CB5E70 ad:0x40CB5E80 ad:0x40CB5E90 ad:0x40CB5EA0 ad:0x40CB5EB0 ad:0x40CB5EC0 ad:0x40CB5ED0 ad:0x40CB5EE0 ad:0x40CB5EF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x1F0 0x1F1 0x1F2 0x1F3 0x1F4 0x1F5 0x1F6 0x1F7 0x1F8 0x1F9 0x1FA 0x1FB 0x1FC 0x1FD 0x1FE 0x1FF)(list ad:0x40CB5F00 ad:0x40CB5F10 ad:0x40CB5F20 ad:0x40CB5F30 ad:0x40CB5F40 ad:0x40CB5F50 ad:0x40CB5F60 ad:0x40CB5F70 ad:0x40CB5F80 ad:0x40CB5F90 ad:0x40CB5FA0 ad:0x40CB5FB0 ad:0x40CB5FC0 ad:0x40CB5FD0 ad:0x40CB5FE0 ad:0x40CB5FF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x200 0x201 0x202 0x203 0x204 0x205 0x206 0x207 0x208 0x209 0x20A 0x20B 0x20C 0x20D 0x20E 0x20F)(list ad:0x40CB6000 ad:0x40CB6010 ad:0x40CB6020 ad:0x40CB6030 ad:0x40CB6040 ad:0x40CB6050 ad:0x40CB6060 ad:0x40CB6070 ad:0x40CB6080 ad:0x40CB6090 ad:0x40CB60A0 ad:0x40CB60B0 ad:0x40CB60C0 ad:0x40CB60D0 ad:0x40CB60E0 ad:0x40CB60F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x210 0x211 0x212 0x213 0x214 0x215 0x216 0x217 0x218 0x219 0x21A 0x21B 0x21C 0x21D 0x21E 0x21F)(list ad:0x40CB6100 ad:0x40CB6110 ad:0x40CB6120 ad:0x40CB6130 ad:0x40CB6140 ad:0x40CB6150 ad:0x40CB6160 ad:0x40CB6170 ad:0x40CB6180 ad:0x40CB6190 ad:0x40CB61A0 ad:0x40CB61B0 ad:0x40CB61C0 ad:0x40CB61D0 ad:0x40CB61E0 ad:0x40CB61F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x220 0x221 0x222 0x223 0x224 0x225 0x226 0x227 0x228 0x229 0x22A 0x22B 0x22C 0x22D 0x22E 0x22F)(list ad:0x40CB6200 ad:0x40CB6210 ad:0x40CB6220 ad:0x40CB6230 ad:0x40CB6240 ad:0x40CB6250 ad:0x40CB6260 ad:0x40CB6270 ad:0x40CB6280 ad:0x40CB6290 ad:0x40CB62A0 ad:0x40CB62B0 ad:0x40CB62C0 ad:0x40CB62D0 ad:0x40CB62E0 ad:0x40CB62F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x230 0x231 0x232 0x233 0x234 0x235 0x236 0x237 0x238 0x239 0x23A 0x23B 0x23C 0x23D 0x23E 0x23F)(list ad:0x40CB6300 ad:0x40CB6310 ad:0x40CB6320 ad:0x40CB6330 ad:0x40CB6340 ad:0x40CB6350 ad:0x40CB6360 ad:0x40CB6370 ad:0x40CB6380 ad:0x40CB6390 ad:0x40CB63A0 ad:0x40CB63B0 ad:0x40CB63C0 ad:0x40CB63D0 ad:0x40CB63E0 ad:0x40CB63F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x240 0x241 0x242 0x243 0x244 0x245 0x246 0x247 0x248 0x249 0x24A 0x24B 0x24C 0x24D 0x24E 0x24F)(list ad:0x40CB6400 ad:0x40CB6410 ad:0x40CB6420 ad:0x40CB6430 ad:0x40CB6440 ad:0x40CB6450 ad:0x40CB6460 ad:0x40CB6470 ad:0x40CB6480 ad:0x40CB6490 ad:0x40CB64A0 ad:0x40CB64B0 ad:0x40CB64C0 ad:0x40CB64D0 ad:0x40CB64E0 ad:0x40CB64F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x250 0x251 0x252 0x253 0x254 0x255 0x256 0x257 0x258 0x259 0x25A 0x25B 0x25C 0x25D 0x25E 0x25F)(list ad:0x40CB6500 ad:0x40CB6510 ad:0x40CB6520 ad:0x40CB6530 ad:0x40CB6540 ad:0x40CB6550 ad:0x40CB6560 ad:0x40CB6570 ad:0x40CB6580 ad:0x40CB6590 ad:0x40CB65A0 ad:0x40CB65B0 ad:0x40CB65C0 ad:0x40CB65D0 ad:0x40CB65E0 ad:0x40CB65F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x260 0x261 0x262 0x263 0x264 0x265 0x266 0x267 0x268 0x269 0x26A 0x26B 0x26C 0x26D 0x26E 0x26F)(list ad:0x40CB6600 ad:0x40CB6610 ad:0x40CB6620 ad:0x40CB6630 ad:0x40CB6640 ad:0x40CB6650 ad:0x40CB6660 ad:0x40CB6670 ad:0x40CB6680 ad:0x40CB6690 ad:0x40CB66A0 ad:0x40CB66B0 ad:0x40CB66C0 ad:0x40CB66D0 ad:0x40CB66E0 ad:0x40CB66F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x270 0x271 0x272 0x273 0x274 0x275 0x276 0x277 0x278 0x279 0x27A 0x27B 0x27C 0x27D 0x27E 0x27F)(list ad:0x40CB6700 ad:0x40CB6710 ad:0x40CB6720 ad:0x40CB6730 ad:0x40CB6740 ad:0x40CB6750 ad:0x40CB6760 ad:0x40CB6770 ad:0x40CB6780 ad:0x40CB6790 ad:0x40CB67A0 ad:0x40CB67B0 ad:0x40CB67C0 ad:0x40CB67D0 ad:0x40CB67E0 ad:0x40CB67F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x280 0x281 0x282 0x283 0x284 0x285 0x286 0x287 0x288 0x289 0x28A 0x28B 0x28C 0x28D 0x28E 0x28F)(list ad:0x40CB6800 ad:0x40CB6810 ad:0x40CB6820 ad:0x40CB6830 ad:0x40CB6840 ad:0x40CB6850 ad:0x40CB6860 ad:0x40CB6870 ad:0x40CB6880 ad:0x40CB6890 ad:0x40CB68A0 ad:0x40CB68B0 ad:0x40CB68C0 ad:0x40CB68D0 ad:0x40CB68E0 ad:0x40CB68F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x290 0x291 0x292 0x293 0x294 0x295 0x296 0x297 0x298 0x299 0x29A 0x29B 0x29C 0x29D 0x29E 0x29F)(list ad:0x40CB6900 ad:0x40CB6910 ad:0x40CB6920 ad:0x40CB6930 ad:0x40CB6940 ad:0x40CB6950 ad:0x40CB6960 ad:0x40CB6970 ad:0x40CB6980 ad:0x40CB6990 ad:0x40CB69A0 ad:0x40CB69B0 ad:0x40CB69C0 ad:0x40CB69D0 ad:0x40CB69E0 ad:0x40CB69F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2A0 0x2A1 0x2A2 0x2A3 0x2A4 0x2A5 0x2A6 0x2A7 0x2A8 0x2A9 0x2AA 0x2AB 0x2AC 0x2AD 0x2AE 0x2AF)(list ad:0x40CB6A00 ad:0x40CB6A10 ad:0x40CB6A20 ad:0x40CB6A30 ad:0x40CB6A40 ad:0x40CB6A50 ad:0x40CB6A60 ad:0x40CB6A70 ad:0x40CB6A80 ad:0x40CB6A90 ad:0x40CB6AA0 ad:0x40CB6AB0 ad:0x40CB6AC0 ad:0x40CB6AD0 ad:0x40CB6AE0 ad:0x40CB6AF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2B0 0x2B1 0x2B2 0x2B3 0x2B4 0x2B5 0x2B6 0x2B7 0x2B8 0x2B9 0x2BA 0x2BB 0x2BC 0x2BD 0x2BE 0x2BF)(list ad:0x40CB6B00 ad:0x40CB6B10 ad:0x40CB6B20 ad:0x40CB6B30 ad:0x40CB6B40 ad:0x40CB6B50 ad:0x40CB6B60 ad:0x40CB6B70 ad:0x40CB6B80 ad:0x40CB6B90 ad:0x40CB6BA0 ad:0x40CB6BB0 ad:0x40CB6BC0 ad:0x40CB6BD0 ad:0x40CB6BE0 ad:0x40CB6BF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2C0 0x2C1 0x2C2 0x2C3 0x2C4 0x2C5 0x2C6 0x2C7 0x2C8 0x2C9 0x2CA 0x2CB 0x2CC 0x2CD 0x2CE 0x2CF)(list ad:0x40CB6C00 ad:0x40CB6C10 ad:0x40CB6C20 ad:0x40CB6C30 ad:0x40CB6C40 ad:0x40CB6C50 ad:0x40CB6C60 ad:0x40CB6C70 ad:0x40CB6C80 ad:0x40CB6C90 ad:0x40CB6CA0 ad:0x40CB6CB0 ad:0x40CB6CC0 ad:0x40CB6CD0 ad:0x40CB6CE0 ad:0x40CB6CF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2D0 0x2D1 0x2D2 0x2D3 0x2D4 0x2D5 0x2D6 0x2D7 0x2D8 0x2D9 0x2DA 0x2DB 0x2DC 0x2DD 0x2DE 0x2DF)(list ad:0x40CB6D00 ad:0x40CB6D10 ad:0x40CB6D20 ad:0x40CB6D30 ad:0x40CB6D40 ad:0x40CB6D50 ad:0x40CB6D60 ad:0x40CB6D70 ad:0x40CB6D80 ad:0x40CB6D90 ad:0x40CB6DA0 ad:0x40CB6DB0 ad:0x40CB6DC0 ad:0x40CB6DD0 ad:0x40CB6DE0 ad:0x40CB6DF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2E0 0x2E1 0x2E2 0x2E3 0x2E4 0x2E5 0x2E6 0x2E7 0x2E8 0x2E9 0x2EA 0x2EB 0x2EC 0x2ED 0x2EE 0x2EF)(list ad:0x40CB6E00 ad:0x40CB6E10 ad:0x40CB6E20 ad:0x40CB6E30 ad:0x40CB6E40 ad:0x40CB6E50 ad:0x40CB6E60 ad:0x40CB6E70 ad:0x40CB6E80 ad:0x40CB6E90 ad:0x40CB6EA0 ad:0x40CB6EB0 ad:0x40CB6EC0 ad:0x40CB6ED0 ad:0x40CB6EE0 ad:0x40CB6EF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x2F0 0x2F1 0x2F2 0x2F3 0x2F4 0x2F5 0x2F6 0x2F7 0x2F8 0x2F9 0x2FA 0x2FB 0x2FC 0x2FD 0x2FE 0x2FF)(list ad:0x40CB6F00 ad:0x40CB6F10 ad:0x40CB6F20 ad:0x40CB6F30 ad:0x40CB6F40 ad:0x40CB6F50 ad:0x40CB6F60 ad:0x40CB6F70 ad:0x40CB6F80 ad:0x40CB6F90 ad:0x40CB6FA0 ad:0x40CB6FB0 ad:0x40CB6FC0 ad:0x40CB6FD0 ad:0x40CB6FE0 ad:0x40CB6FF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x300 0x301 0x302 0x303 0x304 0x305 0x306 0x307 0x308 0x309 0x30A 0x30B 0x30C 0x30D 0x30E 0x30F)(list ad:0x40CB7000 ad:0x40CB7010 ad:0x40CB7020 ad:0x40CB7030 ad:0x40CB7040 ad:0x40CB7050 ad:0x40CB7060 ad:0x40CB7070 ad:0x40CB7080 ad:0x40CB7090 ad:0x40CB70A0 ad:0x40CB70B0 ad:0x40CB70C0 ad:0x40CB70D0 ad:0x40CB70E0 ad:0x40CB70F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x310 0x311 0x312 0x313 0x314 0x315 0x316 0x317 0x318 0x319 0x31A 0x31B 0x31C 0x31D 0x31E 0x31F)(list ad:0x40CB7100 ad:0x40CB7110 ad:0x40CB7120 ad:0x40CB7130 ad:0x40CB7140 ad:0x40CB7150 ad:0x40CB7160 ad:0x40CB7170 ad:0x40CB7180 ad:0x40CB7190 ad:0x40CB71A0 ad:0x40CB71B0 ad:0x40CB71C0 ad:0x40CB71D0 ad:0x40CB71E0 ad:0x40CB71F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x320 0x321 0x322 0x323 0x324 0x325 0x326 0x327 0x328 0x329 0x32A 0x32B 0x32C 0x32D 0x32E 0x32F)(list ad:0x40CB7200 ad:0x40CB7210 ad:0x40CB7220 ad:0x40CB7230 ad:0x40CB7240 ad:0x40CB7250 ad:0x40CB7260 ad:0x40CB7270 ad:0x40CB7280 ad:0x40CB7290 ad:0x40CB72A0 ad:0x40CB72B0 ad:0x40CB72C0 ad:0x40CB72D0 ad:0x40CB72E0 ad:0x40CB72F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x330 0x331 0x332 0x333 0x334 0x335 0x336 0x337 0x338 0x339 0x33A 0x33B 0x33C 0x33D 0x33E 0x33F)(list ad:0x40CB7300 ad:0x40CB7310 ad:0x40CB7320 ad:0x40CB7330 ad:0x40CB7340 ad:0x40CB7350 ad:0x40CB7360 ad:0x40CB7370 ad:0x40CB7380 ad:0x40CB7390 ad:0x40CB73A0 ad:0x40CB73B0 ad:0x40CB73C0 ad:0x40CB73D0 ad:0x40CB73E0 ad:0x40CB73F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x340 0x341 0x342 0x343 0x344 0x345 0x346 0x347 0x348 0x349 0x34A 0x34B 0x34C 0x34D 0x34E 0x34F)(list ad:0x40CB7400 ad:0x40CB7410 ad:0x40CB7420 ad:0x40CB7430 ad:0x40CB7440 ad:0x40CB7450 ad:0x40CB7460 ad:0x40CB7470 ad:0x40CB7480 ad:0x40CB7490 ad:0x40CB74A0 ad:0x40CB74B0 ad:0x40CB74C0 ad:0x40CB74D0 ad:0x40CB74E0 ad:0x40CB74F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x350 0x351 0x352 0x353 0x354 0x355 0x356 0x357 0x358 0x359 0x35A 0x35B 0x35C 0x35D 0x35E 0x35F)(list ad:0x40CB7500 ad:0x40CB7510 ad:0x40CB7520 ad:0x40CB7530 ad:0x40CB7540 ad:0x40CB7550 ad:0x40CB7560 ad:0x40CB7570 ad:0x40CB7580 ad:0x40CB7590 ad:0x40CB75A0 ad:0x40CB75B0 ad:0x40CB75C0 ad:0x40CB75D0 ad:0x40CB75E0 ad:0x40CB75F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x360 0x361 0x362 0x363 0x364 0x365 0x366 0x367 0x368 0x369 0x36A 0x36B 0x36C 0x36D 0x36E 0x36F)(list ad:0x40CB7600 ad:0x40CB7610 ad:0x40CB7620 ad:0x40CB7630 ad:0x40CB7640 ad:0x40CB7650 ad:0x40CB7660 ad:0x40CB7670 ad:0x40CB7680 ad:0x40CB7690 ad:0x40CB76A0 ad:0x40CB76B0 ad:0x40CB76C0 ad:0x40CB76D0 ad:0x40CB76E0 ad:0x40CB76F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x370 0x371 0x372 0x373 0x374 0x375 0x376 0x377 0x378 0x379 0x37A 0x37B 0x37C 0x37D 0x37E 0x37F)(list ad:0x40CB7700 ad:0x40CB7710 ad:0x40CB7720 ad:0x40CB7730 ad:0x40CB7740 ad:0x40CB7750 ad:0x40CB7760 ad:0x40CB7770 ad:0x40CB7780 ad:0x40CB7790 ad:0x40CB77A0 ad:0x40CB77B0 ad:0x40CB77C0 ad:0x40CB77D0 ad:0x40CB77E0 ad:0x40CB77F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x380 0x381 0x382 0x383 0x384 0x385 0x386 0x387 0x388 0x389 0x38A 0x38B 0x38C 0x38D 0x38E 0x38F)(list ad:0x40CB7800 ad:0x40CB7810 ad:0x40CB7820 ad:0x40CB7830 ad:0x40CB7840 ad:0x40CB7850 ad:0x40CB7860 ad:0x40CB7870 ad:0x40CB7880 ad:0x40CB7890 ad:0x40CB78A0 ad:0x40CB78B0 ad:0x40CB78C0 ad:0x40CB78D0 ad:0x40CB78E0 ad:0x40CB78F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x390 0x391 0x392 0x393 0x394 0x395 0x396 0x397 0x398 0x399 0x39A 0x39B 0x39C 0x39D 0x39E 0x39F)(list ad:0x40CB7900 ad:0x40CB7910 ad:0x40CB7920 ad:0x40CB7930 ad:0x40CB7940 ad:0x40CB7950 ad:0x40CB7960 ad:0x40CB7970 ad:0x40CB7980 ad:0x40CB7990 ad:0x40CB79A0 ad:0x40CB79B0 ad:0x40CB79C0 ad:0x40CB79D0 ad:0x40CB79E0 ad:0x40CB79F0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3A0 0x3A1 0x3A2 0x3A3 0x3A4 0x3A5 0x3A6 0x3A7 0x3A8 0x3A9 0x3AA 0x3AB 0x3AC 0x3AD 0x3AE 0x3AF)(list ad:0x40CB7A00 ad:0x40CB7A10 ad:0x40CB7A20 ad:0x40CB7A30 ad:0x40CB7A40 ad:0x40CB7A50 ad:0x40CB7A60 ad:0x40CB7A70 ad:0x40CB7A80 ad:0x40CB7A90 ad:0x40CB7AA0 ad:0x40CB7AB0 ad:0x40CB7AC0 ad:0x40CB7AD0 ad:0x40CB7AE0 ad:0x40CB7AF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3B0 0x3B1 0x3B2 0x3B3 0x3B4 0x3B5 0x3B6 0x3B7 0x3B8 0x3B9 0x3BA 0x3BB 0x3BC 0x3BD 0x3BE 0x3BF)(list ad:0x40CB7B00 ad:0x40CB7B10 ad:0x40CB7B20 ad:0x40CB7B30 ad:0x40CB7B40 ad:0x40CB7B50 ad:0x40CB7B60 ad:0x40CB7B70 ad:0x40CB7B80 ad:0x40CB7B90 ad:0x40CB7BA0 ad:0x40CB7BB0 ad:0x40CB7BC0 ad:0x40CB7BD0 ad:0x40CB7BE0 ad:0x40CB7BF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3C0 0x3C1 0x3C2 0x3C3 0x3C4 0x3C5 0x3C6 0x3C7 0x3C8 0x3C9 0x3CA 0x3CB 0x3CC 0x3CD 0x3CE 0x3CF)(list ad:0x40CB7C00 ad:0x40CB7C10 ad:0x40CB7C20 ad:0x40CB7C30 ad:0x40CB7C40 ad:0x40CB7C50 ad:0x40CB7C60 ad:0x40CB7C70 ad:0x40CB7C80 ad:0x40CB7C90 ad:0x40CB7CA0 ad:0x40CB7CB0 ad:0x40CB7CC0 ad:0x40CB7CD0 ad:0x40CB7CE0 ad:0x40CB7CF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3D0 0x3D1 0x3D2 0x3D3 0x3D4 0x3D5 0x3D6 0x3D7 0x3D8 0x3D9 0x3DA 0x3DB 0x3DC 0x3DD 0x3DE 0x3DF)(list ad:0x40CB7D00 ad:0x40CB7D10 ad:0x40CB7D20 ad:0x40CB7D30 ad:0x40CB7D40 ad:0x40CB7D50 ad:0x40CB7D60 ad:0x40CB7D70 ad:0x40CB7D80 ad:0x40CB7D90 ad:0x40CB7DA0 ad:0x40CB7DB0 ad:0x40CB7DC0 ad:0x40CB7DD0 ad:0x40CB7DE0 ad:0x40CB7DF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3E0 0x3E1 0x3E2 0x3E3 0x3E4 0x3E5 0x3E6 0x3E7 0x3E8 0x3E9 0x3EA 0x3EB 0x3EC 0x3ED 0x3EE 0x3EF)(list ad:0x40CB7E00 ad:0x40CB7E10 ad:0x40CB7E20 ad:0x40CB7E30 ad:0x40CB7E40 ad:0x40CB7E50 ad:0x40CB7E60 ad:0x40CB7E70 ad:0x40CB7E80 ad:0x40CB7E90 ad:0x40CB7EA0 ad:0x40CB7EB0 ad:0x40CB7EC0 ad:0x40CB7ED0 ad:0x40CB7EE0 ad:0x40CB7EF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end repeat 16. (list 0x3F0 0x3F1 0x3F2 0x3F3 0x3F4 0x3F5 0x3F6 0x3F7 0x3F8 0x3F9 0x3FA 0x3FB 0x3FC 0x3FD 0x3FE 0x3FF)(list ad:0x40CB7F00 ad:0x40CB7F10 ad:0x40CB7F20 ad:0x40CB7F30 ad:0x40CB7F40 ad:0x40CB7F50 ad:0x40CB7F60 ad:0x40CB7F70 ad:0x40CB7F80 ad:0x40CB7F90 ad:0x40CB7FA0 ad:0x40CB7FB0 ad:0x40CB7FC0 ad:0x40CB7FD0 ad:0x40CB7FE0 ad:0x40CB7FF0) tree "DESC[$1]" base $2 group.long ($2)++0xB line.long 0x0 "SRAM0_,Description Address Register" hexmask.long 0x0 0.--31. 1. "ADDR,Address field" line.long 0x4 "SRAM1_,Description Data Register" hexmask.long 0x4 0.--31. 1. "DATA,Data field" line.long 0x8 "SRAM2_,Description Control Register" bitfld.long 0x8 6.--7. "SIZE,Size field" "0: 8-bit,1: 16-bit,2: 32-bit,?" bitfld.long 0x8 5. "RT_EN,Restore Enable" "0: Do not use this descriptor for the restore..,1: Use this descriptor for the restore operation" bitfld.long 0x8 4. "SV_EN,Save Enable" "0: Do not use this descriptor in the save operation,1: Use this descriptor in the save operation" newline bitfld.long 0x8 0.--2. "TYPE,Type field" "0: SR,1: WO,2: RMW_OR,3: RMW_AND,4: DELAY,5: POLLING_0,6: POLLING_1,?" tree.end repeat.end tree.end tree "SSARC_LP" base ad:0x40CB8000 group.long 0x0++0xF line.long 0x0 "DESC_CTRL0_0,Descriptor Control0 0 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_0,Descriptor Control1 0 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_0,Descriptor Address Up 0 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_0,Descriptor Address Down 0 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x20++0xF line.long 0x0 "DESC_CTRL0_1,Descriptor Control0 1 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_1,Descriptor Control1 1 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_1,Descriptor Address Up 1 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_1,Descriptor Address Down 1 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x40++0xF line.long 0x0 "DESC_CTRL0_2,Descriptor Control0 2 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_2,Descriptor Control1 2 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_2,Descriptor Address Up 2 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_2,Descriptor Address Down 2 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x60++0xF line.long 0x0 "DESC_CTRL0_3,Descriptor Control0 3 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_3,Descriptor Control1 3 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_3,Descriptor Address Up 3 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_3,Descriptor Address Down 3 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x80++0xF line.long 0x0 "DESC_CTRL0_4,Descriptor Control0 4 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_4,Descriptor Control1 4 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_4,Descriptor Address Up 4 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_4,Descriptor Address Down 4 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0xA0++0xF line.long 0x0 "DESC_CTRL0_5,Descriptor Control0 5 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_5,Descriptor Control1 5 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_5,Descriptor Address Up 5 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_5,Descriptor Address Down 5 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0xC0++0xF line.long 0x0 "DESC_CTRL0_6,Descriptor Control0 6 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_6,Descriptor Control1 6 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_6,Descriptor Address Up 6 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_6,Descriptor Address Down 6 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0xE0++0xF line.long 0x0 "DESC_CTRL0_7,Descriptor Control0 7 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_7,Descriptor Control1 7 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_7,Descriptor Address Up 7 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_7,Descriptor Address Down 7 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x100++0xF line.long 0x0 "DESC_CTRL0_8,Descriptor Control0 8 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_8,Descriptor Control1 8 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_8,Descriptor Address Up 8 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_8,Descriptor Address Down 8 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x120++0xF line.long 0x0 "DESC_CTRL0_9,Descriptor Control0 9 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_9,Descriptor Control1 9 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_9,Descriptor Address Up 9 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_9,Descriptor Address Down 9 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x140++0xF line.long 0x0 "DESC_CTRL0_10,Descriptor Control0 10 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_10,Descriptor Control1 10 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_10,Descriptor Address Up 10 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_10,Descriptor Address Down 10 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x160++0xF line.long 0x0 "DESC_CTRL0_11,Descriptor Control0 11 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_11,Descriptor Control1 11 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_11,Descriptor Address Up 11 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_11,Descriptor Address Down 11 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x180++0xF line.long 0x0 "DESC_CTRL0_12,Descriptor Control0 12 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_12,Descriptor Control1 12 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_12,Descriptor Address Up 12 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_12,Descriptor Address Down 12 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x1A0++0xF line.long 0x0 "DESC_CTRL0_13,Descriptor Control0 13 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_13,Descriptor Control1 13 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_13,Descriptor Address Up 13 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_13,Descriptor Address Down 13 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x1C0++0xF line.long 0x0 "DESC_CTRL0_14,Descriptor Control0 14 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_14,Descriptor Control1 14 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_14,Descriptor Address Up 14 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_14,Descriptor Address Down 14 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x1E0++0xF line.long 0x0 "DESC_CTRL0_15,Descriptor Control0 15 Register" bitfld.long 0x0 21. "RT_ORDER,Restore order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline bitfld.long 0x0 20. "SV_ORDER,Save Order" "0: Descriptors within the group are processed from..,1: Descriptors within the group are processed from.." newline hexmask.long.word 0x0 10.--19. 1. "END,End index" newline hexmask.long.word 0x0 0.--9. 1. "START,Start index" line.long 0x4 "DESC_CTRL1_15,Descriptor Control1 15 Register" bitfld.long 0x4 20. "DL,Domain lock" "0: Unlock,1: Lock" newline bitfld.long 0x4 19. "WL,Write Lock" "0: Group is unlocked (write access allowed),1: Group is locked (write access not allowed)" newline bitfld.long 0x4 18. "RL,Read Lock" "0: Group is unlocked (read access allowed),1: Group is locked (read access not allowed)" newline bitfld.long 0x4 16.--17. "CPUD,CPU Domain" "0,1,2,3" newline hexmask.long.byte 0x4 12.--15. 1. "RT_PRIORITY,Restore Priority" newline hexmask.long.byte 0x4 8.--11. 1. "SV_PRIORITY,Save Priority" newline bitfld.long 0x4 7. "GP_EN,Group Enable" "0: Group disabled,1: Group enabled" newline bitfld.long 0x4 4.--6. "POWER_DOMAIN,This field describes the mapping (0-7) to external request signals from different domains" "0: PGMC_BPC0,1: PGMC_BPC1,2: PGMC_BPC2,3: PGMC_BPC3,4: PGMC_BPC4,5: PGMC_BPC5,6: PGMC_BPC6,7: PGMC_BPC7" newline bitfld.long 0x4 1. "SW_TRIG_RT,Software trigger restore" "0: No software restore request/software restore..,1: Request a software restore operation/software.." newline bitfld.long 0x4 0. "SW_TRIG_SV,Software trigger save" "0: No software save request/software restore..,1: Request a software save operation/software.." line.long 0x8 "DESC_ADDR_UP_15,Descriptor Address Up 15 Register" hexmask.long 0x8 0.--31. 1. "ADDR_UP,Address field (High)" line.long 0xC "DESC_ADDR_DOWN_15,Descriptor Address Down 15 Register" hexmask.long 0xC 0.--31. 1. "ADDR_DOWN,Address field (Low)" group.long 0x200++0x7 line.long 0x0 "CTRL,Control Register" bitfld.long 0x0 31. "SW_RESET,Software reset" "0,1" newline bitfld.long 0x0 27. "DIS_HW_REQ,Save/Restore request disable" "0: PGMC save/restore requests enabled,1: PGMC save/restore requests disabled" line.long 0x4 "INT_STATUS,Interrupt Status Register" eventfld.long 0x4 31. "ADDR_ERR,Address Error field" "0: No address error,1: An address error has occurred" newline eventfld.long 0x4 30. "AHB_ERR,AHB Error field" "0: No AHB error,1: An AHB error has occurred" newline rbitfld.long 0x4 29. "SW_REQ_DONE,Software Request Done" "0: No software triggered requests or software..,1: Atleast one software triggered has been complete" newline eventfld.long 0x4 28. "TIMEOUT,Timeout field" "0: No timeout event,1: A timeout event has occurred" newline eventfld.long 0x4 27. "GROUP_CONFLICT,Group Conflict field" "0: No group conflict error,1: A group conflict error has occurred" newline rbitfld.long 0x4 10.--11. "AHB_RESP,AHB Bus response field" "0,1,2,3" newline hexmask.long.word 0x4 0.--9. 1. "ERR_INDEX,Error Index" group.long 0x20C++0x3 line.long 0x0 "HP_TIMEOUT,HP Timeout Register" hexmask.long 0x0 0.--31. 1. "TIMEOUT_VALUE,Time out value" rgroup.long 0x21C++0x7 line.long 0x0 "HW_GROUP_PENDING,Hardware Request Pending Register" hexmask.long.word 0x0 16.--31. 1. "HW_RESTORE_PENDING,This field indicates which groups are pending for restore from hardware request" newline hexmask.long.word 0x0 0.--15. 1. "HW_SAVE_PENDING,This field indicates which groups are pending for save from hardware request" line.long 0x4 "SW_GROUP_PENDING,Software Request Pending Register" hexmask.long.word 0x4 16.--31. 1. "SW_RESTORE_PENDING,This field indicates which groups are pending for restore from software request" newline hexmask.long.word 0x4 0.--15. 1. "SW_SAVE_PENDING,This field indicates which groups are pending for save from software request" tree.end tree.end sif (cpuis("IMXRT1165-CM7")||cpuis("IMXRT1166-CM7")) tree "SYSTEMCONTROL" base ad:0xE000E000 group.long 0x8++0x3 line.long 0x0 "ACTLR,Auxiliary Control Register." bitfld.long 0x0 28. "DISFPUISSOPT,Disables critical AXI read-under-write" "0: Normal operation.,?" newline bitfld.long 0x0 27. "DISCRITAXIRUW,Disables critical AXI read-under-write" "0: Normal operation. This is backwards compatible..,1: AXI reads to DEV/SO memory. Exclusive reads to.." newline bitfld.long 0x0 26. "DISDYNADD,Disables dynamic allocation of ADD and SUB instructions" "0: Normal operation. Some ADD and SUB instrctions..,1: All ADD and SUB instructions are resolved in EX2." newline hexmask.long.byte 0x0 21.--25. 1. "DISISSCH1,Disables dual-issued." newline hexmask.long.byte 0x0 16.--20. 1. "DISDI,Disables dual-issued." newline bitfld.long 0x0 15. "DISCRITAXIRUR,Disables critical AXI Read-Under-Read." "0: Normal operation.,1: An AXI read to Strongly-Ordered or Device memory.." newline bitfld.long 0x0 14. "DISBTACALLOC,Disables BTAC allocate." "0: Normal operation.,1: No new entries are allocated in Branch Target.." newline bitfld.long 0x0 13. "DISBTACREAD,Disables BTAC read." "0: Normal operation.,1: BTAC is not used and only static branch.." newline bitfld.long 0x0 12. "DISITMATBFLUSH,Disables ITM and DWT ATB flush." "?,1: ITM and DWT ATB flush disabled this bit is.." newline bitfld.long 0x0 11. "DISRAMODE,Disables dynamic read allocate mode for Write-Back Write-Allocate memory regions." "0: Normal operation.,1: Dynamic disabled." newline bitfld.long 0x0 10. "FPEXCODIS,Disables FPU exception outputs." "0: Normal operation.,1: FPU exception outputs are disabled." newline bitfld.long 0x0 2. "DISFOLD,Disables folding of IT instructions." "0: Normal operation.,?" rgroup.long 0xD00++0x3 line.long 0x0 "CPUID,CPUID Base Register" hexmask.long.byte 0x0 24.--31. 1. "IMPLEMENTER,Implementer code" newline hexmask.long.byte 0x0 20.--23. 1. "VARIANT,Indicates processor revision: 0x2 = Revision 2" newline hexmask.long.byte 0x0 16.--19. 1. "ARCHITECTURE,ARCHITECTURE" newline hexmask.long.word 0x0 4.--15. 1. "PARTNO,Indicates part number" newline hexmask.long.byte 0x0 0.--3. 1. "REVISION,Indicates patch release: 0x0 = Patch 0" group.long 0xD04++0x37 line.long 0x0 "ICSR,Interrupt Control and State Register" bitfld.long 0x0 31. "NMIPENDSET,NMI set-pending bit" "0: write: no effect; read: NMI exception is not..,1: write: changes NMI exception state to pending;.." newline bitfld.long 0x0 28. "PENDSVSET,PendSV set-pending bit" "0: write: no effect; read: PendSV exception is not..,1: write: changes PendSV exception state to.." newline bitfld.long 0x0 27. "PENDSVCLR,PendSV clear-pending bit" "0: no effect,1: removes the pending state from the PendSV.." newline bitfld.long 0x0 26. "PENDSTSET,SysTick exception set-pending bit" "0: write: no effect; read: SysTick exception is not..,1: write: changes SysTick exception state to.." newline bitfld.long 0x0 25. "PENDSTCLR,SysTick exception clear-pending bit" "0: no effect,1: removes the pending state from the SysTick.." newline rbitfld.long 0x0 22. "ISRPENDING,Interrupt pending flag excluding NMI and Faults" "0: No external interrupt pending.,1: External interrupt pending." newline hexmask.long.word 0x0 12.--20. 1. "VECTPENDING,Exception number of the highest priority pending enabled exception" newline rbitfld.long 0x0 11. "RETTOBASE,Indicates whether there are preempted active exceptions" "0: there are preempted active exceptions to execute,1: there are no active exceptions or the.." newline hexmask.long.word 0x0 0.--8. 1. "VECTACTIVE,Active exception number" line.long 0x4 "VTOR,Vector Table Offset Register" hexmask.long 0x4 7.--31. 1. "TBLOFF,Vector table base offset" line.long 0x8 "AIRCR,Application Interrupt and Reset Control Register" hexmask.long.word 0x8 16.--31. 1. "VECTKEY,Register key" newline rbitfld.long 0x8 15. "ENDIANNESS,Data endianness" "0: Little-endian,1: Big-endian" newline bitfld.long 0x8 8.--10. "PRIGROUP,Interrupt priority grouping field. This field determines the split of group priority from subpriority." "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 2. "SYSRESETREQ,System reset request" "0: no system reset request,1: asserts a signal to the outer system that.." newline bitfld.long 0x8 1. "VECTCLRACTIVE,Writing 1 to this bit clears all active state information for fixed and configurable exceptions." "0: No change,1: Clears all active state information for fixed.." newline bitfld.long 0x8 0. "VECTRESET,Writing 1 to this bit causes a local system reset" "0: No change,1: Causes a local system reset" line.long 0xC "SCR,System Control Register" bitfld.long 0xC 4. "SEVONPEND,Send Event on Pending bit" "0: only enabled interrupts or events can wakeup the..,1: enabled events and all interrupts including.." newline bitfld.long 0xC 2. "SLEEPDEEP,Controls whether the processor uses sleep or deep sleep as its low power mode" "0: sleep,1: deep sleep" newline bitfld.long 0xC 1. "SLEEPONEXIT,Indicates sleep-on-exit when returning from Handler mode to Thread mode" "0: o not sleep when returning to Thread mode,1: enter sleep or deep sleep on return from an ISR" line.long 0x10 "CCR,Configuration and Control Register" rbitfld.long 0x10 18. "BP,Always reads-as-one. It indicates branch prediction is enabled." "0,1" newline bitfld.long 0x10 17. "IC,Enables L1 instruction cache." "0: L1 instruction cache disabled,1: L1 instruction cache enabled" newline bitfld.long 0x10 16. "DC,Enables L1 data cache." "0: L1 data cache disabled,1: L1 data cache enabled" newline bitfld.long 0x10 9. "STKALIGN,Indicates stack alignment on exception entry" "0: 4-byte aligned,1: 8-byte aligned" newline bitfld.long 0x10 8. "BFHFNMIGN,Enables handlers with priority -1 or -2 to ignore data BusFaults caused by load and store instructions." "0: data bus faults caused by load and store..,1: handlers running at priority -1 and -2 ignore.." newline bitfld.long 0x10 4. "DIV_0_TRP,Enables faulting or halting when the processor executes an SDIV or UDIV instruction with a divisor of 0" "0: do not trap divide by 0,1: trap divide by 0" newline bitfld.long 0x10 3. "UNALIGN_TRP,Enables unaligned access traps" "0: do not trap unaligned halfword and word accesses,1: trap unaligned halfword and word accesses" newline bitfld.long 0x10 1. "USERSETMPEND,Enables unprivileged software access to the STIR" "0: disable,1: enable" newline bitfld.long 0x10 0. "NONBASETHRDENA,Indicates how the processor enters Thread mode" "0: processor can enter Thread mode only when no..,1: processor can enter Thread mode from any level.." line.long 0x14 "SHPR1,System Handler Priority Register 1" hexmask.long.byte 0x14 16.--23. 1. "PRI_6,Priority of system handler 6 UsageFault" newline hexmask.long.byte 0x14 8.--15. 1. "PRI_5,Priority of system handler 5 BusFault" newline hexmask.long.byte 0x14 0.--7. 1. "PRI_4,Priority of system handler 4 MemManage" line.long 0x18 "SHPR2,System Handler Priority Register 2" hexmask.long.byte 0x18 24.--31. 1. "PRI_11,Priority of system handler 11 SVCall" line.long 0x1C "SHPR3,System Handler Priority Register 3" hexmask.long.byte 0x1C 24.--31. 1. "PRI_15,Priority of system handler 15 SysTick exception" newline hexmask.long.byte 0x1C 16.--23. 1. "PRI_14,Priority of system handler 14 PendSV" line.long 0x20 "SHCSR,System Handler Control and State Register" bitfld.long 0x20 18. "USGFAULTENA,UsageFault enable bit" "0: disable the exception,1: enable the exception" newline bitfld.long 0x20 17. "BUSFAULTENA,BusFault enable bit" "0: disable the exception,1: enable the exception" newline bitfld.long 0x20 16. "MEMFAULTENA,MemManage enable bit" "0: disable the exception,1: enable the exception" newline bitfld.long 0x20 15. "SVCALLPENDED,SVCall pending bit" "0: exception is not pending,1: exception is pending" newline bitfld.long 0x20 14. "BUSFAULTPENDED,BusFault exception pending bit" "0: exception is not pending,1: exception is pending" newline bitfld.long 0x20 13. "MEMFAULTPENDED,MemManage exception pending bit" "0: exception is not pending,1: exception is pending" newline bitfld.long 0x20 12. "USGFAULTPENDED,UsageFault exception pending bit" "0: exception is not pending,1: exception is pending" newline bitfld.long 0x20 11. "SYSTICKACT,SysTick exception active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 10. "PENDSVACT,PendSV exception active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 8. "MONITORACT,Debug monitor active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 7. "SVCALLACT,SVCall active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 3. "USGFAULTACT,UsageFault exception active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 1. "BUSFAULTACT,BusFault exception active bit" "0: exception is not active,1: exception is active" newline bitfld.long 0x20 0. "MEMFAULTACT,MemManage exception active bit" "0: exception is not active,1: exception is active" line.long 0x24 "CFSR,Configurable Fault Status Register" bitfld.long 0x24 25. "DIVBYZERO,Divide by zero UsageFault" "0: no divide by zero fault or divide by zero..,1: the processor has executed an SDIV or UDIV.." newline bitfld.long 0x24 24. "UNALIGNED,Unaligned access UsageFault" "0: no unaligned access fault or unaligned access..,1: the processor has made an unaligned memory access" newline bitfld.long 0x24 19. "NOCP,No coprocessor UsageFault" "0: no UsageFault caused by attempting to access a..,1: the processor has attempted to access a.." newline bitfld.long 0x24 18. "INVPC,Invalid PC load UsageFault caused by an invalid PC load by EXC_RETURN" "0: no invalid PC load UsageFault,1: the processor has attempted an illegal load of.." newline bitfld.long 0x24 17. "INVSTATE,Invalid state UsageFault" "0: no invalid state UsageFault,1: the processor has attempted to execute an.." newline bitfld.long 0x24 16. "UNDEFINSTR,Undefined instruction UsageFault" "0: no undefined instruction UsageFault,1: the processor has attempted to execute an.." newline bitfld.long 0x24 15. "BFARVALID,BusFault Address Register (BFAR) valid flag" "0: value in BFAR is not a valid fault address,1: BFAR holds a valid fault address" newline bitfld.long 0x24 13. "LSPERR,Bus fault occurred during floating-point lazy state preservation" "0: No bus fault occurred during floating-point lazy..,1: A bus fault occurred during floating-point lazy.." newline bitfld.long 0x24 12. "STKERR,BusFault on stacking for exception entry" "0: no stacking fault,1: stacking for an exception entry has caused one.." newline bitfld.long 0x24 11. "UNSTKERR,BusFault on unstacking for a return from exception" "0: no unstacking fault,1: unstack for an exception return has caused one.." newline bitfld.long 0x24 10. "IMPRECISERR,Imprecise data bus error" "0: no imprecise data bus error,1: a data bus error has occurred but the return.." newline bitfld.long 0x24 9. "PRECISERR,Precise data bus error" "0: no precise data bus error,1: a data bus error has occurred and the PC value.." newline bitfld.long 0x24 8. "IBUSERR,Instruction bus error" "0: no instruction bus error,1: instruction bus error" newline bitfld.long 0x24 7. "MMARVALID,MemManage Fault Address Register (MMFAR) valid flag" "0: value in MMAR is not a valid fault address,1: MMAR holds a valid fault address" newline bitfld.long 0x24 5. "MLSPERR,MemManage fault occurred during floating-point lazy state preservation" "0: No MemManage fault occurred during..,1: A MemManage fault occurred during floating-point.." newline bitfld.long 0x24 4. "MSTKERR,MemManage fault on stacking for exception entry" "0: no stacking fault,1: stacking for an exception entry has caused one.." newline bitfld.long 0x24 3. "MUNSTKERR,MemManage fault on unstacking for a return from exception" "0: no unstacking fault,1: unstack for an exception return has caused one.." newline bitfld.long 0x24 1. "DACCVIOL,Data access violation flag" "0: no data access violation fault,1: the processor attempted a load or store at a.." newline bitfld.long 0x24 0. "IACCVIOL,Instruction access violation flag" "0: no instruction access violation fault,1: the processor attempted an instruction fetch.." line.long 0x28 "HFSR,HardFault Status register" bitfld.long 0x28 31. "DEBUGEVT,Reserved for Debug use. When writing to the register you must write 0 to this bit otherwise behavior is Unpredictable." "0: No Debug event has occurred.,1: Debug event has occurred. The Debug Fault Status.." newline bitfld.long 0x28 30. "FORCED,Indicates a forced hard fault generated by escalation of a fault with configurable priority that cannot be handles either because of priority or because it is disabled." "0: no forced HardFault,1: forced HardFault" newline bitfld.long 0x28 1. "VECTTBL,Indicates a BusFault on a vector table read during exception processing." "0: no BusFault on vector table read,1: BusFault on vector table read" line.long 0x2C "DFSR,Debug Fault Status Register" bitfld.long 0x2C 4. "EXTERNAL,Debug event generated because of the assertion of an external debug request" "0: No external debug request debug event,1: External debug request debug event" newline bitfld.long 0x2C 3. "VCATCH,Indicates triggering of a Vector catch" "0: No Vector catch triggered,1: Vector catch triggered" newline bitfld.long 0x2C 2. "DWTTRAP,Debug event generated by the DWT" "0: No current debug events generated by the DWT,1: At least one current debug event generated by.." newline bitfld.long 0x2C 1. "BKPT,Debug event generated by BKPT instruction execution or a breakpoint match in FPB" "0: No current breakpoint debug event,1: At least one current breakpoint debug event" newline bitfld.long 0x2C 0. "HALTED,Indicates a debug event generated by either a C_HALT or C_STEP request triggered by a write to the DHCSR or a step request triggered by setting DEMCR.MON_STEP to 1." "0: No active halt request debug event,1: Halt request debug event active" line.long 0x30 "MMFAR,MemManage Fault Address Register" hexmask.long 0x30 0.--31. 1. "ADDRESS,Address of MemManage fault location" line.long 0x34 "BFAR,BusFault Address Register" hexmask.long 0x34 0.--31. 1. "ADDRESS,Address of the BusFault location" rgroup.long 0xD40++0x33 line.long 0x0 "ID_PFR0,Processor Feature Register 0" hexmask.long.byte 0x0 12.--15. 1. "STATE3,ARMv7-M unused" newline hexmask.long.byte 0x0 8.--11. 1. "STATE2,ARMv7-M unused" newline hexmask.long.byte 0x0 4.--7. 1. "STATE1,Thumb instruction set support" newline hexmask.long.byte 0x0 0.--3. 1. "STATE0,ARM instruction set support" line.long 0x4 "ID_PFR1,Processor Feature Register 1" hexmask.long.byte 0x4 8.--11. 1. "PROGMODEL,M profile programmers' model" line.long 0x8 "ID_DFR0,Debug Feature Register" hexmask.long.byte 0x8 20.--23. 1. "DEBUGMODEL,Support for memory-mapped debug model for M profile processors" line.long 0xC "ID_AFR0,Auxiliary Feature Register" hexmask.long.byte 0xC 12.--15. 1. "IMPLEMENTATION_DEFINED3,Gives information about the IMPLEMENTATION DEFINED features of a processor implementation." newline hexmask.long.byte 0xC 8.--11. 1. "IMPLEMENTATION_DEFINED2,Gives information about the IMPLEMENTATION DEFINED features of a processor implementation." newline hexmask.long.byte 0xC 4.--7. 1. "IMPLEMENTATION_DEFINED1,Gives information about the IMPLEMENTATION DEFINED features of a processor implementation." newline hexmask.long.byte 0xC 0.--3. 1. "IMPLEMENTATION_DEFINED0,Gives information about the IMPLEMENTATION DEFINED features of a processor implementation." line.long 0x10 "ID_MMFR0,Memory Model Feature Register 0" hexmask.long.byte 0x10 20.--23. 1. "AUXILIARY_REGISTERS,Indicates the support for Auxiliary registers" newline hexmask.long.byte 0x10 16.--19. 1. "TCM_SUPPORT,Indicates the support for Tightly Coupled Memory" newline hexmask.long.byte 0x10 12.--15. 1. "SHAREABILITY_LEVELS,Indicates the number of shareability levels implemented" newline hexmask.long.byte 0x10 8.--11. 1. "OUTERMOST_SHAREABILITY,Indicates the outermost shareability domain implemented" newline hexmask.long.byte 0x10 4.--7. 1. "PMSASUPPORT,Indicates support for a PMSA" line.long 0x14 "ID_MMFR1,Memory Model Feature Register 1" hexmask.long 0x14 0.--31. 1. "ID_MMFR1,Gives information about the implemented memory model and memory management support." line.long 0x18 "ID_MMFR2,Memory Model Feature Register 2" hexmask.long.byte 0x18 24.--27. 1. "WFI_STALL,Indicates the support for Wait For Interrupt (WFI) stalling" line.long 0x1C "ID_MMFR3,Memory Model Feature Register 3" hexmask.long 0x1C 0.--31. 1. "ID_MMFR3,Gives information about the implemented memory model and memory management support." line.long 0x20 "ID_ISAR0,Instruction Set Attributes Register 0" hexmask.long.byte 0x20 24.--27. 1. "DIVIDE_INSTRS,Indicates the supported Divide instructions" newline hexmask.long.byte 0x20 20.--23. 1. "DEBUG_INSTRS,Indicates the supported Debug instructions" newline hexmask.long.byte 0x20 16.--19. 1. "COPROC_INSTRS,Indicates the supported Coprocessor instructions" newline hexmask.long.byte 0x20 12.--15. 1. "CMPBRANCH_INSTRS,Indicates the supported combined Compare and Branch instructions" newline hexmask.long.byte 0x20 8.--11. 1. "BITFIELD_INSTRS,Indicates the supported BitField instructions" newline hexmask.long.byte 0x20 4.--7. 1. "BITCOUNT_INSTRS,Indicates the supported Bit Counting instructions" line.long 0x24 "ID_ISAR1,Instruction Set Attributes Register 1" hexmask.long.byte 0x24 24.--27. 1. "INTERWORK_INSTRS,Indicates the supported Interworking instructions" newline hexmask.long.byte 0x24 20.--23. 1. "IMMEDIATE_INSTRS,Indicates the support for data-processing instructions with long immediate" newline hexmask.long.byte 0x24 16.--19. 1. "IFTHEN_INSTRS,Indicates the supported IfThen instructions" newline hexmask.long.byte 0x24 12.--15. 1. "EXTEND_INSTRS,Indicates the supported Extend instructions" line.long 0x28 "ID_ISAR2,Instruction Set Attributes Register 2" hexmask.long.byte 0x28 28.--31. 1. "REVERSAL_INSTRS,Indicates the supported Reversal instructions" newline hexmask.long.byte 0x28 20.--23. 1. "MULTU_INSTRS,Indicates the supported advanced unsigned Multiply instructions" newline hexmask.long.byte 0x28 16.--19. 1. "MULTS_INSTRS,Indicates the supported advanced signed Multiply instructions" newline hexmask.long.byte 0x28 12.--15. 1. "MULT_INSTRS,Indicates the supported additional Multiply instructions" newline hexmask.long.byte 0x28 8.--11. 1. "MULTIACCESSINT_INSTRS,Indicates the support for multi-access interruptible instructions" newline hexmask.long.byte 0x28 4.--7. 1. "MEMHINT_INSTRS,Indicates the supported Memory Hint instructions" newline hexmask.long.byte 0x28 0.--3. 1. "LOADSTORE_INSTRS,Indicates the supported additional load and store instructions" line.long 0x2C "ID_ISAR3,Instruction Set Attributes Register 3" hexmask.long.byte 0x2C 24.--27. 1. "TRUENOP_INSTRS,Indicates the supported non flag-setting MOV instructions" newline hexmask.long.byte 0x2C 20.--23. 1. "THUMBCOPY_INSTRS,Indicates the supported non flag-setting MOV instructions" newline hexmask.long.byte 0x2C 16.--19. 1. "TABBRANCH_INSTRS,Indicates the supported Table Branch instructions" newline hexmask.long.byte 0x2C 12.--15. 1. "SYNCHPRIM_INSTRS,Together with the ID_ISAR4[SYNCHPRIM_INSTRS_FRAC] indicates the supported Synchronization Primitives" newline hexmask.long.byte 0x2C 8.--11. 1. "SVC_INSTRS,Indicates the supported SVC instructions" newline hexmask.long.byte 0x2C 4.--7. 1. "SIMD_INSTRS,Indicates the supported SIMD instructions" newline hexmask.long.byte 0x2C 0.--3. 1. "SATURATE_INSTRS,Indicates the supported Saturate instructions" line.long 0x30 "ID_ISAR4,Instruction Set Attributes Register 4" hexmask.long.byte 0x30 24.--27. 1. "PSR_M_INSTRS,Indicates the supported M profile instructions to modify the PSRs" newline hexmask.long.byte 0x30 20.--23. 1. "SYNCHPRIM_INSTRS_FRAC,Together with the ID_ISAR3[SYNCHPRIM_INSTRS] indicates the supported Synchronization Primitives" newline hexmask.long.byte 0x30 16.--19. 1. "BARRIER_INSTRS,Indicates the supported Barrier instructions" newline hexmask.long.byte 0x30 8.--11. 1. "WRITEBACK_INSTRS,Indicates the support for Writeback addressing modes" newline hexmask.long.byte 0x30 4.--7. 1. "WITHSHIFTS_INSTRS,Indicates the support for instructions with shifts" newline hexmask.long.byte 0x30 0.--3. 1. "UNPRIV_INSTRS,Indicates the supported unprivileged instructions. These are the instruction variants indicated by a T suffix." rgroup.long 0xD78++0xB line.long 0x0 "CLIDR,Cache Level ID register" bitfld.long 0x0 27.--29. "LOU,Level of Unification for the cache hierarchy" "0: 0,1: 1,2: 2,3: 3,4: 4,5: 5,6: 6,7: 7" newline bitfld.long 0x0 24.--26. "LOC,Level of Coherency for the cache hierarchy" "0: 0,1: 1,2: 2,3: 3,4: 4,5: 5,6: 6,7: 7" newline bitfld.long 0x0 21.--23. "LOUIS,Level of Unification Inner Shareable for the cache hierarchy. This field is RAZ." "0: 0,1: 1,2: 2,3: 3,4: 4,5: 5,6: 6,7: 7" newline bitfld.long 0x0 18.--20. "CL7,Indicate the type of cache implemented at level 7." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 15.--17. "CL6,Indicate the type of cache implemented at level 6." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 12.--14. "CL5,Indicate the type of cache implemented at level 5." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 9.--11. "CL4,Indicate the type of cache implemented at level 4." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 6.--8. "CL3,Indicate the type of cache implemented at level 3." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 3.--5. "CL2,Indicate the type of cache implemented at level 2." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" newline bitfld.long 0x0 0.--2. "CL1,Indicate the type of cache implemented at level 1." "0: No cache,1: Instruction cache only,2: Data cache only,3: Separate instruction and data caches,4: Unified cache,?,?,?" line.long 0x4 "CTR,Cache Type register" bitfld.long 0x4 29.--31. "FORMAT,Indicates the implemented CTR format." "?,?,?,?,4: ARMv7 format.,?,?,?" newline hexmask.long.byte 0x4 24.--27. 1. "CWG,Cache Write-back Granule. The maximum size of memory that can be overwritten as a result of the eviction of a cache entry that has had a memory location in it modified encoded as Log2 of the number of words." newline hexmask.long.byte 0x4 20.--23. 1. "ERG,Exclusives Reservation Granule. The maximum size of the reservation granule that has been implemented for the Load-Exclusive and Store-Exclusive instructions encoded as Log2 of the number of words." newline hexmask.long.byte 0x4 16.--19. 1. "DMINLINE,Log2 of the number of words in the smallest cache line of all the data caches and unified caches that are controlled by the processor." newline hexmask.long.byte 0x4 0.--3. 1. "IMINLINE,Log2 of the number of words in the smallest cache line of all the instruction caches that are controlled by the processor." line.long 0x8 "CCSIDR,Cache Size ID Register" bitfld.long 0x8 31. "WT,Indicates whether the cache level supports write-through" "0: Feature not supported,1: Feature supported" newline bitfld.long 0x8 30. "WB,Indicates whether the cache level supports write-back" "0: Feature not supported,1: Feature supported" newline bitfld.long 0x8 29. "RA,Indicates whether the cache level supports read-allocation" "0: Feature not supported,1: Feature supported" newline bitfld.long 0x8 28. "WA,Indicates whether the cache level supports write-allocation" "0: Feature not supported,1: Feature supported" newline hexmask.long.word 0x8 13.--27. 1. "NUMSETS,(Number of sets in cache) - 1 therefore a value of 0 indicates 1 set in the cache. The number of sets does not have to be a power of 2." newline hexmask.long.word 0x8 3.--12. 1. "ASSOCIATIVITY,(Associativity of cache) - 1 therefore a value of 0 indicates an associativity of 1. The associativity does not have to be a power of 2." newline bitfld.long 0x8 0.--2. "LINESIZE,(Log2(Number of words in cache line)) - 2." "0: The line length of 4 words.,1: The line length of 8 words.,2: The line length of 16 words.,3: The line length of 32 words.,4: The line length of 64 words.,5: The line length of 128 words.,6: The line length of 256 words.,7: The line length of 512 words." group.long 0xD84++0x7 line.long 0x0 "CSSELR,Cache Size Selection Register" bitfld.long 0x0 1.--3. "LEVEL,Cache level of required cache" "0: Level 1 cache.,1: Level 2 cache.,2: Level 3 cache.,3: Level 4 cache.,4: Level 5 cache.,5: Level 6 cache.,6: Level 7 cache.,?" newline bitfld.long 0x0 0. "IND,Instruction not data bit" "0: Data or unified cache.,1: Instruction cache." line.long 0x4 "CPACR,Coprocessor Access Control Register" bitfld.long 0x4 22.--23. "CP11,Access privileges for coprocessor 11." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 20.--21. "CP10,Access privileges for coprocessor 10." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 14.--15. "CP7,Access privileges for coprocessor 7." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 12.--13. "CP6,Access privileges for coprocessor 6." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 10.--11. "CP5,Access privileges for coprocessor 5." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 8.--9. "CP4,Access privileges for coprocessor 4." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 6.--7. "CP3,Access privileges for coprocessor 3." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 4.--5. "CP2,Access privileges for coprocessor 2." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 2.--3. "CP1,Access privileges for coprocessor 1." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." newline bitfld.long 0x4 0.--1. "CP0,Access privileges for coprocessor 0." "0: Access denied. Any attempted access generates a..,1: Privileged access only. An unprivileged access..,?,3: Full access." wgroup.long 0xF00++0x3 line.long 0x0 "STIR,Instruction cache invalidate all to Point of Unification (PoU)" hexmask.long.word 0x0 0.--8. 1. "INTID,Indicates the interrupt to be triggered" wgroup.long 0xF50++0x3 line.long 0x0 "ICIALLU,Instruction cache invalidate all to Point of Unification (PoU)" hexmask.long 0x0 0.--31. 1. "ICIALLU,I-cache invalidate all to PoU" wgroup.long 0xF58++0x1F line.long 0x0 "ICIMVAU,Instruction cache invalidate by address to PoU" hexmask.long 0x0 0.--31. 1. "ICIMVAU,I-cache invalidate by MVA to PoU" line.long 0x4 "DCIMVAC,Data cache invalidate by address to Point of Coherency (PoC)" hexmask.long 0x4 0.--31. 1. "DCIMVAC,D-cache invalidate by MVA to PoC" line.long 0x8 "DCISW,Data cache invalidate by set/way" hexmask.long 0x8 0.--31. 1. "DCISW,D-cache invalidate by set-way" line.long 0xC "DCCMVAU,Data cache by address to PoU" hexmask.long 0xC 0.--31. 1. "DCCMVAU,D-cache clean by MVA to PoU" line.long 0x10 "DCCMVAC,Data cache clean by address to PoC" hexmask.long 0x10 0.--31. 1. "DCCMVAC,D-cache clean by MVA to PoC" line.long 0x14 "DCCSW,Data cache clean by set/way" hexmask.long 0x14 0.--31. 1. "DCCSW,D-cache clean by set-way" line.long 0x18 "DCCIMVAC,Data cache clean and invalidate by address to PoC" hexmask.long 0x18 0.--31. 1. "DCCIMVAC,D-cache clean and invalidate by MVA to PoC" line.long 0x1C "DCCISW,Data cache clean and invalidate by set/way" hexmask.long 0x1C 0.--31. 1. "DCCISW,D-cache clean and invalidate by set-way" group.long 0xF90++0x13 line.long 0x0 "CM7_ITCMCR,Instruction Tightly-Coupled Memory Control Register" hexmask.long.byte 0x0 3.--6. 1. "SZ,TCM size. Indicates the size of the relevant TCM." newline bitfld.long 0x0 2. "RETEN,Retry phase enable. When enabled the processor guarantees to honor the retry output on the corresponding TCM interface re-executing the instruction which carried out the TCM access." "0: Retry phase disabled.,1: Retry phase enabled." newline bitfld.long 0x0 1. "RMW,Read-Modify-Write (RMW) enable. Indicates that all writes to TCM that are not the full width of the TCM RAM use a RMW sequence." "0: RMW disabled.,1: RMW enabled." newline bitfld.long 0x0 0. "EN,TCM enable. When a TCM is disabled all accesses are made to the AXIM interface." "0: TCM disabled.,1: TCM enabled." line.long 0x4 "CM7_DTCMCR,Data Tightly-Coupled Memory Control Register" hexmask.long.byte 0x4 3.--6. 1. "SZ,TCM size. Indicates the size of the relevant TCM." newline bitfld.long 0x4 2. "RETEN,Retry phase enable. When enabled the processor guarantees to honor the retry output on the corresponding TCM interface re-executing the instruction which carried out the TCM access." "0: Retry phase disabled.,1: Retry phase enabled." newline bitfld.long 0x4 1. "RMW,Read-Modify-Write (RMW) enable. Indicates that all writes to TCM that are not the full width of the TCM RAM use a RMW sequence." "0: RMW disabled.,1: RMW enabled." newline bitfld.long 0x4 0. "EN,TCM enable. When a TCM is disabled all accesses are made to the AXIM interface." "0: TCM disabled.,1: TCM enabled." line.long 0x8 "CM7_AHBPCR,AHBP Control Register" rbitfld.long 0x8 1.--3. "SZ,AHBP size." "0: 0MB. AHBP disabled.,1: 64MB.,2: 128MB.,3: 256MB.,4: 512MB.,?,?,?" newline bitfld.long 0x8 0. "EN,AHBP enable." "0: AHBP disabled. When disabled all accesses are..,1: AHBP enabled." line.long 0xC "CM7_CACR,L1 Cache Control Register" bitfld.long 0xC 2. "FORCEWT,Enables Force Write-Through in the data cache." "0: Disables Force Write-Through.,1: Enables Force Write-Through. All Cacheable.." newline bitfld.long 0xC 1. "ECCDIS,Enables ECC in the instruction and data cache." "0: Enables ECC in the instruction and data cache.,1: Disables ECC in the instruction and data cache." newline bitfld.long 0xC 0. "SIWT,Shared cacheable-is-WT for data cache. Enables limited cache coherency usage." "0: Normal Cacheable Shared locations are treated as..,1: Normal Cacheable shared locations are treated as.." line.long 0x10 "CM7_AHBSCR,AHB Slave Control Register" hexmask.long.byte 0x10 11.--15. 1. "INITCOUNT,Fairness counter initialization value." newline hexmask.long.word 0x10 2.--10. 1. "TPRI,Threshold execution priority for AHBS traffic demotion." newline bitfld.long 0x10 0.--1. "CTL,AHBS prioritization control." "0: AHBS access priority demoted. This is the reset..,1: Software access priority demoted.,2: AHBS access priority demoted by initializing the..,3: AHBSPRI signal has control of access priority." group.long 0xFA8++0x3 line.long 0x0 "CM7_ABFSR,Auxiliary Bus Fault Status Register" bitfld.long 0x0 8.--9. "AXIMTYPE,Indicates the type of fault on the AXIM interface. Only valid when AXIM is 1." "0: OKAY.,1: EXOKAY.,2: SLVERR.,3: DECERR." newline bitfld.long 0x0 4. "EPPB,Asynchronous fault on EPPB interface." "0,1" newline bitfld.long 0x0 3. "AXIM,Asynchronous fault on AXIM interface." "0,1" newline bitfld.long 0x0 2. "AHBP,Asynchronous fault on AHBP interface." "0,1" newline bitfld.long 0x0 1. "DTCM,Asynchronous fault on DTCM interface." "0,1" newline bitfld.long 0x0 0. "ITCM,Asynchronous fault on ITCM interface." "0,1" tree.end endif tree "TMPSNS" base ad:0x0 group.long 0x0++0x3F line.long 0x0 "CTRL0,Temperature Sensor Control Register 0" hexmask.long.byte 0x0 12.--15. 1. "IBIAS_TRIM,Current bias trim value" bitfld.long 0x0 8.--9. "V_SEL,Voltage Select" "0: Normal temperature measuring mode,?,?,?" newline hexmask.long.byte 0x0 0.--5. 1. "SLOPE_CAL,Ramp slope calibration control" line.long 0x4 "CTRL0_SET,Temperature Sensor Control Register 0" hexmask.long.byte 0x4 12.--15. 1. "IBIAS_TRIM,Current bias trim value" bitfld.long 0x4 8.--9. "V_SEL,Voltage Select" "0,1,2,3" newline hexmask.long.byte 0x4 0.--5. 1. "SLOPE_CAL,Ramp slope calibration control" line.long 0x8 "CTRL0_CLR,Temperature Sensor Control Register 0" hexmask.long.byte 0x8 12.--15. 1. "IBIAS_TRIM,Current bias trim value" eventfld.long 0x8 8.--9. "V_SEL,Voltage Select" "0,1,2,3" newline hexmask.long.byte 0x8 0.--5. 1. "SLOPE_CAL,Ramp slope calibration control" line.long 0xC "CTRL0_TOG,Temperature Sensor Control Register 0" hexmask.long.byte 0xC 12.--15. 1. "IBIAS_TRIM,Current bias trim value" bitfld.long 0xC 8.--9. "V_SEL,Voltage Select" "0,1,2,3" newline hexmask.long.byte 0xC 0.--5. 1. "SLOPE_CAL,Ramp slope calibration control" line.long 0x10 "CTRL1,Temperature Sensor Control Register 1" bitfld.long 0x10 31. "PWD_FULL,Temperature Sensor Full Power Down" "0: Sensor is active,1: Sensor is powered down" hexmask.long.byte 0x10 24.--30. 1. "RFU,Read/Writeable field. Reserved for future use" newline bitfld.long 0x10 23. "PWD,Temperature Sensor Power Down" "0: Sensor is active,1: Sensor is powered down" bitfld.long 0x10 22. "START,Start Temperature Measurement" "0: No new temperature reading taken,1: Initiate a new temperature reading" newline bitfld.long 0x10 19. "PANIC_TEMP_IE,Panic temperature interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x10 18. "HIGH_TEMP_IE,High temperature interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline bitfld.long 0x10 17. "LOW_TEMP_IE,Low temperature interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" bitfld.long 0x10 16. "FINISH_IE,Measurement finished interrupt enable" "0: Interrupt is disabled,1: Interrupt is enabled" newline hexmask.long.word 0x10 0.--15. 1. "FREQ,Temperature Measurement Frequency" line.long 0x14 "CTRL1_SET,Temperature Sensor Control Register 1" bitfld.long 0x14 31. "PWD_FULL,Temperature Sensor Full Power Down" "0,1" hexmask.long.byte 0x14 24.--30. 1. "RFU,Read/Writeable field. Reserved for future use" newline bitfld.long 0x14 23. "PWD,Temperature Sensor Power Down" "0,1" bitfld.long 0x14 22. "START,Start Temperature Measurement" "0,1" newline bitfld.long 0x14 19. "PANIC_TEMP_IE,Panic temperature interrupt enable" "0,1" bitfld.long 0x14 18. "HIGH_TEMP_IE,High temperature interrupt enable" "0,1" newline bitfld.long 0x14 17. "LOW_TEMP_IE,Low temperature interrupt enable" "0,1" bitfld.long 0x14 16. "FINISH_IE,Measurement finished interrupt enable" "0,1" newline hexmask.long.word 0x14 0.--15. 1. "FREQ,Temperature Measurement Frequency" line.long 0x18 "CTRL1_CLR,Temperature Sensor Control Register 1" eventfld.long 0x18 31. "PWD_FULL,Temperature Sensor Full Power Down" "0,1" hexmask.long.byte 0x18 24.--30. 1. "RFU,Read/Writeable field. Reserved for future use" newline eventfld.long 0x18 23. "PWD,Temperature Sensor Power Down" "0,1" eventfld.long 0x18 22. "START,Start Temperature Measurement" "0,1" newline eventfld.long 0x18 19. "PANIC_TEMP_IE,Panic temperature interrupt enable" "0,1" eventfld.long 0x18 18. "HIGH_TEMP_IE,High temperature interrupt enable" "0,1" newline eventfld.long 0x18 17. "LOW_TEMP_IE,Low temperature interrupt enable" "0,1" eventfld.long 0x18 16. "FINISH_IE,Measurement finished interrupt enable" "0,1" newline hexmask.long.word 0x18 0.--15. 1. "FREQ,Temperature Measurement Frequency" line.long 0x1C "CTRL1_TOG,Temperature Sensor Control Register 1" bitfld.long 0x1C 31. "PWD_FULL,Temperature Sensor Full Power Down" "0,1" hexmask.long.byte 0x1C 24.--30. 1. "RFU,Read/Writeable field. Reserved for future use" newline bitfld.long 0x1C 23. "PWD,Temperature Sensor Power Down" "0,1" bitfld.long 0x1C 22. "START,Start Temperature Measurement" "0,1" newline bitfld.long 0x1C 19. "PANIC_TEMP_IE,Panic temperature interrupt enable" "0,1" bitfld.long 0x1C 18. "HIGH_TEMP_IE,High temperature interrupt enable" "0,1" newline bitfld.long 0x1C 17. "LOW_TEMP_IE,Low temperature interrupt enable" "0,1" bitfld.long 0x1C 16. "FINISH_IE,Measurement finished interrupt enable" "0,1" newline hexmask.long.word 0x1C 0.--15. 1. "FREQ,Temperature Measurement Frequency" line.long 0x20 "RANGE0,Temperature Sensor Range Register 0" hexmask.long.word 0x20 16.--27. 1. "HIGH_TEMP_VAL,High temperature threshold value" hexmask.long.word 0x20 0.--11. 1. "LOW_TEMP_VAL,Low temperature threshold value" line.long 0x24 "RANGE0_SET,Temperature Sensor Range Register 0" hexmask.long.word 0x24 16.--27. 1. "HIGH_TEMP_VAL,High temperature threshold value" hexmask.long.word 0x24 0.--11. 1. "LOW_TEMP_VAL,Low temperature threshold value" line.long 0x28 "RANGE0_CLR,Temperature Sensor Range Register 0" hexmask.long.word 0x28 16.--27. 1. "HIGH_TEMP_VAL,High temperature threshold value" hexmask.long.word 0x28 0.--11. 1. "LOW_TEMP_VAL,Low temperature threshold value" line.long 0x2C "RANGE0_TOG,Temperature Sensor Range Register 0" hexmask.long.word 0x2C 16.--27. 1. "HIGH_TEMP_VAL,High temperature threshold value" hexmask.long.word 0x2C 0.--11. 1. "LOW_TEMP_VAL,Low temperature threshold value" line.long 0x30 "RANGE1,Temperature Sensor Range Register 1" hexmask.long.word 0x30 0.--11. 1. "PANIC_TEMP_VAL,Panic temperature threshold value" line.long 0x34 "RANGE1_SET,Temperature Sensor Range Register 1" hexmask.long.word 0x34 0.--11. 1. "PANIC_TEMP_VAL,Panic temperature threshold value" line.long 0x38 "RANGE1_CLR,Temperature Sensor Range Register 1" hexmask.long.word 0x38 0.--11. 1. "PANIC_TEMP_VAL,Panic temperature threshold value" line.long 0x3C "RANGE1_TOG,Temperature Sensor Range Register 1" hexmask.long.word 0x3C 0.--11. 1. "PANIC_TEMP_VAL,Panic temperature threshold value" group.long 0x50++0x3 line.long 0x0 "STATUS0,Temperature Sensor Status Register 0" eventfld.long 0x0 19. "PANIC_TEMP,Panic temperature alarm bit" "0: No Panic temperature alert,1: Panic temperature alert" eventfld.long 0x0 18. "HIGH_TEMP,High temperature alarm bit" "0: No High temperature alert,1: High temperature alert" newline eventfld.long 0x0 17. "LOW_TEMP,Low temperature alarm bit" "0: No Low temperature alert,1: Low temperature alert" eventfld.long 0x0 16. "FINISH,Temperature measurement complete" "0: Temperature sensor is busy (if CTRL1[START] =..,1: Temperature reading is complete and new.." newline hexmask.long.word 0x0 0.--11. 1. "TEMP_VAL,Measured temperature value" tree.end tree "TMR" base ad:0x0 tree "TMR1" base ad:0x4015C000 group.word 0x0++0x19 line.word 0x0 "COMP10,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP20,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT0,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD0,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD0,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR0,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL0,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL0,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD10,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD20,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL0,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT0,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA0,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x1E++0x1B line.word 0x0 "ENBL,Timer Channel Enable Register" hexmask.word.byte 0x0 0.--3. 1. "ENBL,Timer Channel Enable" line.word 0x2 "COMP11,Timer Channel Compare Register 1" hexmask.word 0x2 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x4 "COMP21,Timer Channel Compare Register 2" hexmask.word 0x4 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x6 "CAPT1,Timer Channel Capture Register" hexmask.word 0x6 0.--15. 1. "CAPTURE,Capture Value" line.word 0x8 "LOAD1,Timer Channel Load Register" hexmask.word 0x8 0.--15. 1. "LOAD,Timer Load Register" line.word 0xA "HOLD1,Timer Channel Hold Register" hexmask.word 0xA 0.--15. 1. "HOLD,HOLD" line.word 0xC "CNTR1,Timer Channel Counter Register" hexmask.word 0xC 0.--15. 1. "COUNTER,COUNTER" line.word 0xE "CTRL1,Timer Channel Control Register" bitfld.word 0xE 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xE 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xE 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xE 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xE 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xE 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xE 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xE 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0x10 "SCTRL1,Timer Channel Status and Control Register" bitfld.word 0x10 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0x10 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0x10 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0x10 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0x10 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0x10 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0x10 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0x10 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0x10 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0x10 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0x10 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0x10 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x12 "CMPLD11,Timer Channel Comparator Load Register 1" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x14 "CMPLD21,Timer Channel Comparator Load Register 2" hexmask.word 0x14 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x16 "CSCTRL1,Timer Channel Comparator Status and Control Register" bitfld.word 0x16 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x16 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x16 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x16 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x16 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x16 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x16 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x16 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x16 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x16 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x16 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x16 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x18 "FILT1,Timer Channel Input Filter Register" bitfld.word 0x18 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x18 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x1A "DMA1,Timer Channel DMA Enable Register" bitfld.word 0x1A 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x1A 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x1A 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x40++0x19 line.word 0x0 "COMP12,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP22,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT2,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD2,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD2,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR2,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL2,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL2,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD12,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD22,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL2,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT2,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA2,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x60++0x19 line.word 0x0 "COMP13,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP23,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT3,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD3,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD3,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR3,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL3,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL3,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD13,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD23,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL3,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT3,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA3,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" tree.end tree "TMR2" base ad:0x40160000 group.word 0x0++0x19 line.word 0x0 "COMP10,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP20,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT0,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD0,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD0,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR0,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL0,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL0,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD10,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD20,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL0,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT0,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA0,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x1E++0x1B line.word 0x0 "ENBL,Timer Channel Enable Register" hexmask.word.byte 0x0 0.--3. 1. "ENBL,Timer Channel Enable" line.word 0x2 "COMP11,Timer Channel Compare Register 1" hexmask.word 0x2 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x4 "COMP21,Timer Channel Compare Register 2" hexmask.word 0x4 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x6 "CAPT1,Timer Channel Capture Register" hexmask.word 0x6 0.--15. 1. "CAPTURE,Capture Value" line.word 0x8 "LOAD1,Timer Channel Load Register" hexmask.word 0x8 0.--15. 1. "LOAD,Timer Load Register" line.word 0xA "HOLD1,Timer Channel Hold Register" hexmask.word 0xA 0.--15. 1. "HOLD,HOLD" line.word 0xC "CNTR1,Timer Channel Counter Register" hexmask.word 0xC 0.--15. 1. "COUNTER,COUNTER" line.word 0xE "CTRL1,Timer Channel Control Register" bitfld.word 0xE 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xE 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xE 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xE 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xE 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xE 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xE 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xE 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0x10 "SCTRL1,Timer Channel Status and Control Register" bitfld.word 0x10 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0x10 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0x10 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0x10 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0x10 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0x10 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0x10 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0x10 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0x10 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0x10 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0x10 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0x10 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x12 "CMPLD11,Timer Channel Comparator Load Register 1" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x14 "CMPLD21,Timer Channel Comparator Load Register 2" hexmask.word 0x14 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x16 "CSCTRL1,Timer Channel Comparator Status and Control Register" bitfld.word 0x16 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x16 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x16 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x16 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x16 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x16 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x16 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x16 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x16 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x16 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x16 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x16 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x18 "FILT1,Timer Channel Input Filter Register" bitfld.word 0x18 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x18 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x1A "DMA1,Timer Channel DMA Enable Register" bitfld.word 0x1A 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x1A 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x1A 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x40++0x19 line.word 0x0 "COMP12,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP22,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT2,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD2,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD2,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR2,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL2,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL2,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD12,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD22,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL2,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT2,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA2,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x60++0x19 line.word 0x0 "COMP13,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP23,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT3,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD3,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD3,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR3,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL3,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL3,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD13,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD23,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL3,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT3,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA3,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" tree.end tree "TMR3" base ad:0x40164000 group.word 0x0++0x19 line.word 0x0 "COMP10,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP20,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT0,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD0,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD0,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR0,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL0,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL0,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD10,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD20,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL0,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT0,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA0,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x1E++0x1B line.word 0x0 "ENBL,Timer Channel Enable Register" hexmask.word.byte 0x0 0.--3. 1. "ENBL,Timer Channel Enable" line.word 0x2 "COMP11,Timer Channel Compare Register 1" hexmask.word 0x2 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x4 "COMP21,Timer Channel Compare Register 2" hexmask.word 0x4 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x6 "CAPT1,Timer Channel Capture Register" hexmask.word 0x6 0.--15. 1. "CAPTURE,Capture Value" line.word 0x8 "LOAD1,Timer Channel Load Register" hexmask.word 0x8 0.--15. 1. "LOAD,Timer Load Register" line.word 0xA "HOLD1,Timer Channel Hold Register" hexmask.word 0xA 0.--15. 1. "HOLD,HOLD" line.word 0xC "CNTR1,Timer Channel Counter Register" hexmask.word 0xC 0.--15. 1. "COUNTER,COUNTER" line.word 0xE "CTRL1,Timer Channel Control Register" bitfld.word 0xE 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xE 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xE 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xE 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xE 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xE 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xE 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xE 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0x10 "SCTRL1,Timer Channel Status and Control Register" bitfld.word 0x10 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0x10 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0x10 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0x10 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0x10 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0x10 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0x10 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0x10 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0x10 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0x10 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0x10 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0x10 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x12 "CMPLD11,Timer Channel Comparator Load Register 1" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x14 "CMPLD21,Timer Channel Comparator Load Register 2" hexmask.word 0x14 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x16 "CSCTRL1,Timer Channel Comparator Status and Control Register" bitfld.word 0x16 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x16 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x16 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x16 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x16 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x16 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x16 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x16 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x16 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x16 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x16 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x16 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x18 "FILT1,Timer Channel Input Filter Register" bitfld.word 0x18 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x18 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x1A "DMA1,Timer Channel DMA Enable Register" bitfld.word 0x1A 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x1A 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x1A 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x40++0x19 line.word 0x0 "COMP12,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP22,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT2,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD2,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD2,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR2,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL2,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL2,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD12,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD22,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL2,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT2,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA2,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x60++0x19 line.word 0x0 "COMP13,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP23,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT3,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD3,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD3,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR3,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL3,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL3,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD13,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD23,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL3,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT3,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA3,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" tree.end tree "TMR4" base ad:0x40168000 group.word 0x0++0x19 line.word 0x0 "COMP10,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP20,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT0,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD0,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD0,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR0,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL0,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL0,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD10,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD20,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL0,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT0,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA0,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x1E++0x1B line.word 0x0 "ENBL,Timer Channel Enable Register" hexmask.word.byte 0x0 0.--3. 1. "ENBL,Timer Channel Enable" line.word 0x2 "COMP11,Timer Channel Compare Register 1" hexmask.word 0x2 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x4 "COMP21,Timer Channel Compare Register 2" hexmask.word 0x4 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x6 "CAPT1,Timer Channel Capture Register" hexmask.word 0x6 0.--15. 1. "CAPTURE,Capture Value" line.word 0x8 "LOAD1,Timer Channel Load Register" hexmask.word 0x8 0.--15. 1. "LOAD,Timer Load Register" line.word 0xA "HOLD1,Timer Channel Hold Register" hexmask.word 0xA 0.--15. 1. "HOLD,HOLD" line.word 0xC "CNTR1,Timer Channel Counter Register" hexmask.word 0xC 0.--15. 1. "COUNTER,COUNTER" line.word 0xE "CTRL1,Timer Channel Control Register" bitfld.word 0xE 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xE 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xE 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xE 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xE 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xE 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xE 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xE 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0x10 "SCTRL1,Timer Channel Status and Control Register" bitfld.word 0x10 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0x10 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0x10 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0x10 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0x10 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0x10 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0x10 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0x10 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0x10 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0x10 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0x10 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0x10 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0x10 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x12 "CMPLD11,Timer Channel Comparator Load Register 1" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x14 "CMPLD21,Timer Channel Comparator Load Register 2" hexmask.word 0x14 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x16 "CSCTRL1,Timer Channel Comparator Status and Control Register" bitfld.word 0x16 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x16 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x16 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x16 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x16 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x16 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x16 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x16 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x16 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x16 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x16 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x16 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x18 "FILT1,Timer Channel Input Filter Register" bitfld.word 0x18 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x18 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x1A "DMA1,Timer Channel DMA Enable Register" bitfld.word 0x1A 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x1A 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x1A 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x40++0x19 line.word 0x0 "COMP12,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP22,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT2,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD2,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD2,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR2,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL2,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL2,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD12,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD22,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL2,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT2,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA2,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" group.word 0x60++0x19 line.word 0x0 "COMP13,Timer Channel Compare Register 1" hexmask.word 0x0 0.--15. 1. "COMPARISON_1,Comparison Value 1" line.word 0x2 "COMP23,Timer Channel Compare Register 2" hexmask.word 0x2 0.--15. 1. "COMPARISON_2,Comparison Value 2" line.word 0x4 "CAPT3,Timer Channel Capture Register" hexmask.word 0x4 0.--15. 1. "CAPTURE,Capture Value" line.word 0x6 "LOAD3,Timer Channel Load Register" hexmask.word 0x6 0.--15. 1. "LOAD,Timer Load Register" line.word 0x8 "HOLD3,Timer Channel Hold Register" hexmask.word 0x8 0.--15. 1. "HOLD,HOLD" line.word 0xA "CNTR3,Timer Channel Counter Register" hexmask.word 0xA 0.--15. 1. "COUNTER,COUNTER" line.word 0xC "CTRL3,Timer Channel Control Register" bitfld.word 0xC 13.--15. "CM,Count Mode" "0: No operation,1: Count rising edges of primary sourceRising edges..,2: Count rising and falling edges of primary..,3: Count rising edges of primary source while..,4: Quadrature count mode uses primary and secondary..,5: Count rising edges of primary source; secondary..,6: Edge of secondary source triggers primary count..,7: Cascaded counter mode (up/down)The primary count.." hexmask.word.byte 0xC 9.--12. 1. "PCS,Primary Count Source" newline bitfld.word 0xC 7.--8. "SCS,Secondary Count Source" "0: Counter 0 input pin,1: Counter 1 input pin,2: Counter 2 input pin,3: Counter 3 input pin" bitfld.word 0xC 6. "ONCE,Count Once" "0: Count repeatedly.,1: Count until compare and then stop. If counting.." newline bitfld.word 0xC 5. "LENGTH,Count Length" "0: Count until roll over at FFFF and continue from..,1: Count until compare then re-initialize. If.." bitfld.word 0xC 4. "DIR,Count Direction" "0: Count up.,1: Count down." newline bitfld.word 0xC 3. "COINIT,Co-Channel Initialization" "0: Co-channel counter/timers cannot force a..,1: Co-channel counter/timers may force a.." bitfld.word 0xC 0.--2. "OUTMODE,Output Mode" "0: Asserted while counter is active,1: Clear OFLAG output on successful compare,2: Set OFLAG output on successful compare,3: Toggle OFLAG output on successful compare,4: Toggle OFLAG output using alternating compare..,5: Set on compare cleared on secondary source input..,6: Set on compare cleared on counter rollover,7: Enable gated clock output while counter is active" line.word 0xE "SCTRL3,Timer Channel Status and Control Register" bitfld.word 0xE 15. "TCF,Timer Compare Flag" "0,1" bitfld.word 0xE 14. "TCFIE,Timer Compare Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 13. "TOF,Timer Overflow Flag" "0,1" bitfld.word 0xE 12. "TOFIE,Timer Overflow Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 11. "IEF,Input Edge Flag" "0,1" bitfld.word 0xE 10. "IEFIE,Input Edge Flag Interrupt Enable" "0,1" newline bitfld.word 0xE 9. "IPS,Input Polarity Select" "0,1" rbitfld.word 0xE 8. "INPUT,External Input Signal" "0,1" newline bitfld.word 0xE 6.--7. "CAPTURE_MODE,Input Capture Mode" "0: Capture function is disabled,1: Load capture register on rising edge (when..,2: Load capture register on falling edge (when..,3: Load capture register on both edges of input" bitfld.word 0xE 5. "MSTR,Master Mode" "0,1" newline bitfld.word 0xE 4. "EEOF,Enable External OFLAG Force" "0,1" bitfld.word 0xE 3. "VAL,Forced OFLAG Value" "0,1" newline bitfld.word 0xE 2. "FORCE,Force OFLAG Output" "0,1" bitfld.word 0xE 1. "OPS,Output Polarity Select" "0: True polarity.,1: Inverted polarity." newline bitfld.word 0xE 0. "OEN,Output Enable" "0: The external pin is configured as an input.,1: The OFLAG output signal is driven on the.." line.word 0x10 "CMPLD13,Timer Channel Comparator Load Register 1" hexmask.word 0x10 0.--15. 1. "COMPARATOR_LOAD_1,COMPARATOR_LOAD_1" line.word 0x12 "CMPLD23,Timer Channel Comparator Load Register 2" hexmask.word 0x12 0.--15. 1. "COMPARATOR_LOAD_2,COMPARATOR_LOAD_2" line.word 0x14 "CSCTRL3,Timer Channel Comparator Status and Control Register" bitfld.word 0x14 14.--15. "DBG_EN,Debug Actions Enable" "0: Continue with normal operation during debug..,1: Halt TMR counter during debug mode.,2: Force TMR output to logic 0 (prior to..,3: Both halt counter and force output to 0 during.." bitfld.word 0x14 13. "FAULT,Fault Enable" "0: Fault function disabled.,1: Fault function enabled." newline bitfld.word 0x14 12. "ALT_LOAD,Alternative Load Enable" "0: Counter can be re-initialized only with the LOAD..,1: Counter can be re-initialized with the LOAD or.." bitfld.word 0x14 11. "ROC,Reload on Capture" "0: Do not reload the counter on a capture event.,1: Reload the counter on a capture event." newline bitfld.word 0x14 10. "TCI,Triggered Count Initialization Control" "0: Stop counter upon receiving a second trigger..,1: Reload the counter upon receiving a second.." rbitfld.word 0x14 9. "UP,Counting Direction Indicator" "0: The last count was in the DOWN direction.,1: The last count was in the UP direction." newline bitfld.word 0x14 7. "TCF2EN,Timer Compare 2 Interrupt Enable" "0,1" bitfld.word 0x14 6. "TCF1EN,Timer Compare 1 Interrupt Enable" "0,1" newline bitfld.word 0x14 5. "TCF2,Timer Compare 2 Interrupt Flag" "0,1" bitfld.word 0x14 4. "TCF1,Timer Compare 1 Interrupt Flag" "0,1" newline bitfld.word 0x14 2.--3. "CL2,Compare Load Control 2" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" bitfld.word 0x14 0.--1. "CL1,Compare Load Control 1" "0: Never preload,1: Load upon successful compare with the value in..,2: Load upon successful compare with the value in..,?" line.word 0x16 "FILT3,Timer Channel Input Filter Register" bitfld.word 0x16 8.--10. "FILT_CNT,Input Filter Sample Count" "0,1,2,3,4,5,6,7" hexmask.word.byte 0x16 0.--7. 1. "FILT_PER,Input Filter Sample Period" line.word 0x18 "DMA3,Timer Channel DMA Enable Register" bitfld.word 0x18 2. "CMPLD2DE,Comparator Preload Register 2 DMA Enable" "0,1" bitfld.word 0x18 1. "CMPLD1DE,Comparator Preload Register 1 DMA Enable" "0,1" newline bitfld.word 0x18 0. "IEFDE,Input Edge Flag DMA Enable" "0,1" tree.end tree.end tree "USB" base ad:0x0 tree "USB_OTG1" base ad:0x40430000 rgroup.long 0x0++0x17 line.long 0x0 "ID,Identification register" hexmask.long.byte 0x0 16.--23. 1. "REVISION,REVISION" newline hexmask.long.byte 0x0 8.--13. 1. "NID,NID" newline hexmask.long.byte 0x0 0.--5. 1. "ID,ID" line.long 0x4 "HWGENERAL,Hardware General" bitfld.long 0x4 9.--10. "SM,SM" "0: No Serial Engine always use parallel signalling.,1: Serial Engine present always use serial..,2: Software programmable - Reset to use parallel..,3: Software programmable - Reset to use serial.." newline bitfld.long 0x4 6.--8. "PHYM,PHYM" "0: UTMI/UMTI+,1: ULPI DDR,2: ULPI,3: Serial Only,4: Software programmable - reset to UTMI/UTMI+,5: Software programmable - reset to ULPI DDR,6: Software programmable - reset to ULPI,7: Software programmable - reset to Serial" newline bitfld.long 0x4 4.--5. "PHYW,PHYW" "0: 8 bit wide data bus (Software non-programmable),1: 16 bit wide data bus (Software non-programmable),2: Reset to 8 bit wide data bus (Software..,3: Reset to 16 bit wide data bus (Software.." line.long 0x8 "HWHOST,Host Hardware Parameters" bitfld.long 0x8 1.--3. "NPORT,NPORT" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 0. "HC,HC" "0: Not supported,1: Supported" line.long 0xC "HWDEVICE,Device Hardware Parameters" hexmask.long.byte 0xC 1.--5. 1. "DEVEP,DEVEP" newline bitfld.long 0xC 0. "DC,DC" "0: Not supported,1: Supported" line.long 0x10 "HWTXBUF,TX Buffer Hardware Parameters" hexmask.long.byte 0x10 16.--23. 1. "TXCHANADD,TXCHANADD" newline hexmask.long.byte 0x10 0.--7. 1. "TXBURST,TXBURST" line.long 0x14 "HWRXBUF,RX Buffer Hardware Parameters" hexmask.long.byte 0x14 8.--15. 1. "RXADD,RXADD" newline hexmask.long.byte 0x14 0.--7. 1. "RXBURST,RXBURST" group.long 0x80++0x13 line.long 0x0 "GPTIMER0LD,General Purpose Timer #0 Load" hexmask.long.tbyte 0x0 0.--23. 1. "GPTLD,GPTLD" line.long 0x4 "GPTIMER0CTRL,General Purpose Timer #0 Controller" bitfld.long 0x4 31. "GPTRUN,GPTRUN" "0: Stop counting,1: Run" newline bitfld.long 0x4 30. "GPTRST,GPTRST" "0: No action,1: Load counter value from GPTLD bits in n_GPTIMER0LD" newline bitfld.long 0x4 24. "GPTMODE,GPTMODE" "0: One Shot Mode,1: Repeat Mode" newline hexmask.long.tbyte 0x4 0.--23. 1. "GPTCNT,GPTCNT" line.long 0x8 "GPTIMER1LD,General Purpose Timer #1 Load" hexmask.long.tbyte 0x8 0.--23. 1. "GPTLD,GPTLD" line.long 0xC "GPTIMER1CTRL,General Purpose Timer #1 Controller" bitfld.long 0xC 31. "GPTRUN,GPTRUN" "0: Stop counting,1: Run" newline bitfld.long 0xC 30. "GPTRST,GPTRST" "0: No action,1: Load counter value from GPTLD bits in.." newline bitfld.long 0xC 24. "GPTMODE,GPTMODE" "0: One Shot Mode,1: Repeat Mode" newline hexmask.long.tbyte 0xC 0.--23. 1. "GPTCNT,GPTCNT" line.long 0x10 "SBUSCFG,System Bus Config" bitfld.long 0x10 0.--2. "AHBBRST,AHBBRST" "0: Incremental burst of unspecified length only,1: INCR4 burst then single transfer,2: INCR8 burst INCR4 burst then single transfer,3: INCR16 burst INCR8 burst INCR4 burst then single..,?,5: INCR4 burst then incremental burst of..,6: INCR8 burst INCR4 burst then incremental burst..,7: INCR16 burst INCR8 burst INCR4 burst then.." rgroup.byte 0x100++0x0 line.byte 0x0 "CAPLENGTH,Capability Registers Length" hexmask.byte 0x0 0.--7. 1. "CAPLENGTH,CAPLENGTH" rgroup.word 0x102++0x1 line.word 0x0 "HCIVERSION,Host Controller Interface Version" hexmask.word 0x0 0.--15. 1. "HCIVERSION,HCIVERSION" rgroup.long 0x104++0x7 line.long 0x0 "HCSPARAMS,Host Controller Structural Parameters" hexmask.long.byte 0x0 24.--27. 1. "N_TT,N_TT" newline hexmask.long.byte 0x0 20.--23. 1. "N_PTT,N_PTT" newline bitfld.long 0x0 16. "PI,PI" "0,1" newline hexmask.long.byte 0x0 12.--15. 1. "N_CC,N_CC" newline hexmask.long.byte 0x0 8.--11. 1. "N_PCC,N_PCC" newline bitfld.long 0x0 4. "PPC,PPC" "0,1" newline hexmask.long.byte 0x0 0.--3. 1. "N_PORTS,N_PORTS" line.long 0x4 "HCCPARAMS,Host Controller Capability Parameters" hexmask.long.byte 0x4 8.--15. 1. "EECP,EECP" newline hexmask.long.byte 0x4 4.--7. 1. "IST,IST" newline bitfld.long 0x4 2. "ASP,ASP" "0,1" newline bitfld.long 0x4 1. "PFL,PFL" "0,1" newline bitfld.long 0x4 0. "ADC,ADC" "0,1" rgroup.word 0x120++0x1 line.word 0x0 "DCIVERSION,Device Controller Interface Version" hexmask.word 0x0 0.--15. 1. "DCIVERSION,DCIVERSION" rgroup.long 0x124++0x3 line.long 0x0 "DCCPARAMS,Device Controller Capability Parameters" bitfld.long 0x0 8. "HC,HC" "0,1" newline bitfld.long 0x0 7. "DC,DC" "0,1" newline hexmask.long.byte 0x0 0.--4. 1. "DEN,DEN" group.long 0x140++0xF line.long 0x0 "USBCMD,USB Command Register" hexmask.long.byte 0x0 16.--23. 1. "ITC,ITC" newline bitfld.long 0x0 15. "FS_2,FS_2" "0,1" newline bitfld.long 0x0 14. "ATDTW,ATDTW" "0,1" newline bitfld.long 0x0 13. "SUTW,SUTW" "0,1" newline bitfld.long 0x0 11. "ASPE,ASPE" "0,1" newline bitfld.long 0x0 8.--9. "ASP,ASP" "0,1,2,3" newline bitfld.long 0x0 6. "IAA,IAA" "0,1" newline bitfld.long 0x0 5. "ASE,ASE" "0: Do not process the Asynchronous Schedule.,1: Use the ASYNCLISTADDR register to access the.." newline bitfld.long 0x0 4. "PSE,PSE" "0: Do not process the Periodic Schedule,1: Use the PERIODICLISTBASE register to access the.." newline bitfld.long 0x0 2.--3. "FS_1,FS_1" "0,1,2,3" newline bitfld.long 0x0 1. "RST,RST" "0,1" newline bitfld.long 0x0 0. "RS,RS" "0,1" line.long 0x4 "USBSTS,USB Status Register" bitfld.long 0x4 25. "TI1,TI1" "0,1" newline bitfld.long 0x4 24. "TI0,TI0" "0,1" newline rbitfld.long 0x4 16. "NAKI,NAKI" "0,1" newline bitfld.long 0x4 15. "AS,AS" "0,1" newline bitfld.long 0x4 14. "PS,PS" "0,1" newline bitfld.long 0x4 13. "RCL,RCL" "0,1" newline bitfld.long 0x4 12. "HCH,HCH" "0,1" newline bitfld.long 0x4 10. "ULPII,ULPII" "0,1" newline bitfld.long 0x4 8. "SLI,SLI" "0,1" newline bitfld.long 0x4 7. "SRI,SRI" "0,1" newline bitfld.long 0x4 6. "URI,URI" "0,1" newline bitfld.long 0x4 5. "AAI,AAI" "0,1" newline bitfld.long 0x4 4. "SEI,SEI" "0,1" newline bitfld.long 0x4 3. "FRI,FRI" "0,1" newline bitfld.long 0x4 2. "PCI,PCI" "0,1" newline bitfld.long 0x4 1. "UEI,UEI" "0,1" newline bitfld.long 0x4 0. "UI,UI" "0,1" line.long 0x8 "USBINTR,Interrupt Enable Register" bitfld.long 0x8 25. "TIE1,TIE1" "0,1" newline bitfld.long 0x8 24. "TIE0,TIE0" "0,1" newline bitfld.long 0x8 19. "UPIE,UPIE" "0,1" newline bitfld.long 0x8 18. "UAIE,UAIE" "0,1" newline bitfld.long 0x8 16. "NAKE,NAKE" "0,1" newline bitfld.long 0x8 10. "ULPIE,ULPIE" "0,1" newline bitfld.long 0x8 8. "SLE,SLE" "0,1" newline bitfld.long 0x8 7. "SRE,SRE" "0,1" newline bitfld.long 0x8 6. "URE,URE" "0,1" newline bitfld.long 0x8 5. "AAE,AAE" "0,1" newline bitfld.long 0x8 4. "SEE,SEE" "0,1" newline bitfld.long 0x8 3. "FRE,FRE" "0,1" newline bitfld.long 0x8 2. "PCE,PCE" "0,1" newline bitfld.long 0x8 1. "UEE,UEE" "0,1" newline bitfld.long 0x8 0. "UE,UE" "0,1" line.long 0xC "FRINDEX,USB Frame Index" hexmask.long.word 0xC 0.--13. 1. "FRINDEX,FRINDEX" group.long 0x154++0x3 line.long 0x0 "DEVICEADDR,Device Address" hexmask.long.byte 0x0 25.--31. 1. "USBADR,USBADR" newline bitfld.long 0x0 24. "USBADRA,USBADRA" "0,1" group.long 0x154++0x7 line.long 0x0 "PERIODICLISTBASE,Frame List Base Address" hexmask.long.tbyte 0x0 12.--31. 1. "BASEADR,BASEADR" line.long 0x4 "ASYNCLISTADDR,Next Asynch. Address" hexmask.long 0x4 5.--31. 1. "ASYBASE,ASYBASE" group.long 0x158++0x3 line.long 0x0 "ENDPTLISTADDR,Endpoint List Address" hexmask.long.tbyte 0x0 11.--31. 1. "EPBASE,EPBASE" group.long 0x160++0x7 line.long 0x0 "BURSTSIZE,Programmable Burst Size" hexmask.long.word 0x0 8.--16. 1. "TXPBURST,TXPBURST" newline hexmask.long.byte 0x0 0.--7. 1. "RXPBURST,RXPBURST" line.long 0x4 "TXFILLTUNING,TX FIFO Fill Tuning" hexmask.long.byte 0x4 16.--21. 1. "TXFIFOTHRES,TXFIFOTHRES" newline hexmask.long.byte 0x4 8.--12. 1. "TXSCHHEALTH,TXSCHHEALTH" newline hexmask.long.byte 0x4 0.--7. 1. "TXSCHOH,TXSCHOH" group.long 0x178++0x7 line.long 0x0 "ENDPTNAK,Endpoint NAK" hexmask.long.byte 0x0 16.--23. 1. "EPTN,EPTN" newline hexmask.long.byte 0x0 0.--7. 1. "EPRN,EPRN" line.long 0x4 "ENDPTNAKEN,Endpoint NAK Enable" hexmask.long.byte 0x4 16.--23. 1. "EPTNE,EPTNE" newline hexmask.long.byte 0x4 0.--7. 1. "EPRNE,EPRNE" rgroup.long 0x180++0x3 line.long 0x0 "CONFIGFLAG,Configure Flag Register" bitfld.long 0x0 0. "CF,CF" "0: Port routing control logic default-routes each..,1: Port routing control logic default-routes all.." group.long 0x184++0x3 line.long 0x0 "PORTSC1,Port Status & Control" bitfld.long 0x0 30.--31. "PTS_1,PTS_1" "0,1,2,3" newline bitfld.long 0x0 29. "STS,STS" "0,1" newline bitfld.long 0x0 28. "PTW,PTW" "0: Select the 8-bit UTMI interface [60MHz],1: Select the 16-bit UTMI interface [30MHz]" newline bitfld.long 0x0 26.--27. "PSPD,PSPD" "0: Full Speed,1: Low Speed,2: High Speed,3: Undefined" newline bitfld.long 0x0 25. "PTS_2,PTS_2" "0,1" newline bitfld.long 0x0 24. "PFSC,PFSC" "0: Normal operation,1: Forced to full speed" newline bitfld.long 0x0 23. "PHCD,PHCD" "0: Enable PHY clock,1: Disable PHY clock" newline bitfld.long 0x0 22. "WKOC,WKOC" "0,1" newline bitfld.long 0x0 21. "WKDC,WKDC" "0,1" newline bitfld.long 0x0 20. "WKCN,WKCN" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "PTC,PTC" newline bitfld.long 0x0 14.--15. "PIC,PIC" "0: Port indicators are off,1: Amber,2: Green,3: Undefined" newline bitfld.long 0x0 13. "PO,PO" "0,1" newline bitfld.long 0x0 12. "PP,PP" "0,1" newline bitfld.long 0x0 10.--11. "LS,LS" "0: SE0,1: K-state,2: J-state,3: Undefined" newline rbitfld.long 0x0 9. "HSP,HSP" "0,1" newline bitfld.long 0x0 8. "PR,PR" "0,1" newline bitfld.long 0x0 7. "SUSP,SUSP" "0,1" newline bitfld.long 0x0 6. "FPR,FPR" "0,1" newline bitfld.long 0x0 5. "OCC,OCC" "0,1" newline rbitfld.long 0x0 4. "OCA,OCA" "0: This port does not have an over-current condition.,1: This port currently has an over-current condition" newline bitfld.long 0x0 3. "PEC,PEC" "0,1" newline bitfld.long 0x0 2. "PE,PE" "0,1" newline bitfld.long 0x0 1. "CSC,CSC" "0,1" newline rbitfld.long 0x0 0. "CCS,CCS" "0,1" group.long 0x1A4++0x13 line.long 0x0 "OTGSC,On-The-Go Status & control" bitfld.long 0x0 30. "DPIE,DPIE" "0,1" newline bitfld.long 0x0 29. "EN_1MS,EN_1MS" "0,1" newline bitfld.long 0x0 28. "BSEIE,BSEIE" "0,1" newline bitfld.long 0x0 27. "BSVIE,BSVIE" "0,1" newline bitfld.long 0x0 26. "ASVIE,ASVIE" "0,1" newline bitfld.long 0x0 25. "AVVIE,AVVIE" "0,1" newline bitfld.long 0x0 24. "IDIE,IDIE" "0,1" newline bitfld.long 0x0 22. "DPIS,DPIS" "0,1" newline bitfld.long 0x0 21. "STATUS_1MS,STATUS_1MS" "0,1" newline bitfld.long 0x0 20. "BSEIS,BSEIS" "0,1" newline bitfld.long 0x0 19. "BSVIS,BSVIS" "0,1" newline bitfld.long 0x0 18. "ASVIS,ASVIS" "0,1" newline bitfld.long 0x0 17. "AVVIS,AVVIS" "0,1" newline bitfld.long 0x0 16. "IDIS,IDIS" "0,1" newline rbitfld.long 0x0 14. "DPS,DPS" "0,1" newline rbitfld.long 0x0 13. "TOG_1MS,TOG_1MS" "0,1" newline rbitfld.long 0x0 12. "BSE,BSE" "0,1" newline rbitfld.long 0x0 11. "BSV,BSV" "0,1" newline rbitfld.long 0x0 10. "ASV,ASV" "0,1" newline rbitfld.long 0x0 9. "AVV,AVV" "0,1" newline rbitfld.long 0x0 8. "ID,ID" "0,1" newline bitfld.long 0x0 5. "IDPU,IDPU" "0,1" newline bitfld.long 0x0 4. "DP,DP" "0,1" newline bitfld.long 0x0 3. "OT,OT" "0,1" newline bitfld.long 0x0 1. "VC,VC" "0,1" newline bitfld.long 0x0 0. "VD,VD" "0,1" line.long 0x4 "USBMODE,USB Device Mode" bitfld.long 0x4 4. "SDIS,SDIS" "0,1" newline bitfld.long 0x4 3. "SLOM,SLOM" "0: Setup Lockouts On (default);,1: Setup Lockouts Off" newline bitfld.long 0x4 2. "ES,ES" "0: Little Endian [Default],1: Big Endian" newline bitfld.long 0x4 0.--1. "CM,CM" "0: Idle [Default for combination host/device],?,2: Device Controller [Default for device only..,3: Host Controller [Default for host only controller]" line.long 0x8 "ENDPTSETUPSTAT,Endpoint Setup Status" hexmask.long.word 0x8 0.--15. 1. "ENDPTSETUPSTAT,ENDPTSETUPSTAT" line.long 0xC "ENDPTPRIME,Endpoint Prime" hexmask.long.byte 0xC 16.--23. 1. "PETB,PETB" newline hexmask.long.byte 0xC 0.--7. 1. "PERB,PERB" line.long 0x10 "ENDPTFLUSH,Endpoint Flush" hexmask.long.byte 0x10 16.--23. 1. "FETB,FETB" newline hexmask.long.byte 0x10 0.--7. 1. "FERB,FERB" rgroup.long 0x1B8++0x3 line.long 0x0 "ENDPTSTAT,Endpoint Status" hexmask.long.byte 0x0 16.--23. 1. "ETBR,ETBR" newline hexmask.long.byte 0x0 0.--7. 1. "ERBR,ERBR" group.long 0x1BC++0x23 line.long 0x0 "ENDPTCOMPLETE,Endpoint Complete" hexmask.long.byte 0x0 16.--23. 1. "ETCE,ETCE" newline hexmask.long.byte 0x0 0.--7. 1. "ERCE,ERCE" line.long 0x4 "ENDPTCTRL0,Endpoint Control0" bitfld.long 0x4 23. "TXE,TXE" "0,1" newline bitfld.long 0x4 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x4 16. "TXS,TXS" "0,1" newline bitfld.long 0x4 7. "RXE,RXE" "0,1" newline bitfld.long 0x4 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x4 0. "RXS,RXS" "0,1" line.long 0x8 "ENDPTCTRL1,Endpoint Control 1" bitfld.long 0x8 23. "TXE,TXE" "0,1" newline bitfld.long 0x8 22. "TXR,TXR" "0,1" newline bitfld.long 0x8 21. "TXI,TXI" "0,1" newline bitfld.long 0x8 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x8 17. "TXD,TXD" "0,1" newline bitfld.long 0x8 16. "TXS,TXS" "0,1" newline bitfld.long 0x8 7. "RXE,RXE" "0,1" newline bitfld.long 0x8 6. "RXR,RXR" "0,1" newline bitfld.long 0x8 5. "RXI,RXI" "0,1" newline bitfld.long 0x8 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x8 1. "RXD,RXD" "0,1" newline bitfld.long 0x8 0. "RXS,RXS" "0,1" line.long 0xC "ENDPTCTRL2,Endpoint Control 2" bitfld.long 0xC 23. "TXE,TXE" "0,1" newline bitfld.long 0xC 22. "TXR,TXR" "0,1" newline bitfld.long 0xC 21. "TXI,TXI" "0,1" newline bitfld.long 0xC 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0xC 17. "TXD,TXD" "0,1" newline bitfld.long 0xC 16. "TXS,TXS" "0,1" newline bitfld.long 0xC 7. "RXE,RXE" "0,1" newline bitfld.long 0xC 6. "RXR,RXR" "0,1" newline bitfld.long 0xC 5. "RXI,RXI" "0,1" newline bitfld.long 0xC 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0xC 1. "RXD,RXD" "0,1" newline bitfld.long 0xC 0. "RXS,RXS" "0,1" line.long 0x10 "ENDPTCTRL3,Endpoint Control 3" bitfld.long 0x10 23. "TXE,TXE" "0,1" newline bitfld.long 0x10 22. "TXR,TXR" "0,1" newline bitfld.long 0x10 21. "TXI,TXI" "0,1" newline bitfld.long 0x10 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x10 17. "TXD,TXD" "0,1" newline bitfld.long 0x10 16. "TXS,TXS" "0,1" newline bitfld.long 0x10 7. "RXE,RXE" "0,1" newline bitfld.long 0x10 6. "RXR,RXR" "0,1" newline bitfld.long 0x10 5. "RXI,RXI" "0,1" newline bitfld.long 0x10 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x10 1. "RXD,RXD" "0,1" newline bitfld.long 0x10 0. "RXS,RXS" "0,1" line.long 0x14 "ENDPTCTRL4,Endpoint Control 4" bitfld.long 0x14 23. "TXE,TXE" "0,1" newline bitfld.long 0x14 22. "TXR,TXR" "0,1" newline bitfld.long 0x14 21. "TXI,TXI" "0,1" newline bitfld.long 0x14 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x14 17. "TXD,TXD" "0,1" newline bitfld.long 0x14 16. "TXS,TXS" "0,1" newline bitfld.long 0x14 7. "RXE,RXE" "0,1" newline bitfld.long 0x14 6. "RXR,RXR" "0,1" newline bitfld.long 0x14 5. "RXI,RXI" "0,1" newline bitfld.long 0x14 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x14 1. "RXD,RXD" "0,1" newline bitfld.long 0x14 0. "RXS,RXS" "0,1" line.long 0x18 "ENDPTCTRL5,Endpoint Control 5" bitfld.long 0x18 23. "TXE,TXE" "0,1" newline bitfld.long 0x18 22. "TXR,TXR" "0,1" newline bitfld.long 0x18 21. "TXI,TXI" "0,1" newline bitfld.long 0x18 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x18 17. "TXD,TXD" "0,1" newline bitfld.long 0x18 16. "TXS,TXS" "0,1" newline bitfld.long 0x18 7. "RXE,RXE" "0,1" newline bitfld.long 0x18 6. "RXR,RXR" "0,1" newline bitfld.long 0x18 5. "RXI,RXI" "0,1" newline bitfld.long 0x18 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x18 1. "RXD,RXD" "0,1" newline bitfld.long 0x18 0. "RXS,RXS" "0,1" line.long 0x1C "ENDPTCTRL6,Endpoint Control 6" bitfld.long 0x1C 23. "TXE,TXE" "0,1" newline bitfld.long 0x1C 22. "TXR,TXR" "0,1" newline bitfld.long 0x1C 21. "TXI,TXI" "0,1" newline bitfld.long 0x1C 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x1C 17. "TXD,TXD" "0,1" newline bitfld.long 0x1C 16. "TXS,TXS" "0,1" newline bitfld.long 0x1C 7. "RXE,RXE" "0,1" newline bitfld.long 0x1C 6. "RXR,RXR" "0,1" newline bitfld.long 0x1C 5. "RXI,RXI" "0,1" newline bitfld.long 0x1C 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x1C 1. "RXD,RXD" "0,1" newline bitfld.long 0x1C 0. "RXS,RXS" "0,1" line.long 0x20 "ENDPTCTRL7,Endpoint Control 7" bitfld.long 0x20 23. "TXE,TXE" "0,1" newline bitfld.long 0x20 22. "TXR,TXR" "0,1" newline bitfld.long 0x20 21. "TXI,TXI" "0,1" newline bitfld.long 0x20 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x20 17. "TXD,TXD" "0,1" newline bitfld.long 0x20 16. "TXS,TXS" "0,1" newline bitfld.long 0x20 7. "RXE,RXE" "0,1" newline bitfld.long 0x20 6. "RXR,RXR" "0,1" newline bitfld.long 0x20 5. "RXI,RXI" "0,1" newline bitfld.long 0x20 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x20 1. "RXD,RXD" "0,1" newline bitfld.long 0x20 0. "RXS,RXS" "0,1" tree.end tree "USB_OTG2" base ad:0x4042C000 rgroup.long 0x0++0x17 line.long 0x0 "ID,Identification register" hexmask.long.byte 0x0 16.--23. 1. "REVISION,REVISION" newline hexmask.long.byte 0x0 8.--13. 1. "NID,NID" newline hexmask.long.byte 0x0 0.--5. 1. "ID,ID" line.long 0x4 "HWGENERAL,Hardware General" bitfld.long 0x4 9.--10. "SM,SM" "0: No Serial Engine always use parallel signalling.,1: Serial Engine present always use serial..,2: Software programmable - Reset to use parallel..,3: Software programmable - Reset to use serial.." newline bitfld.long 0x4 6.--8. "PHYM,PHYM" "0: UTMI/UMTI+,1: ULPI DDR,2: ULPI,3: Serial Only,4: Software programmable - reset to UTMI/UTMI+,5: Software programmable - reset to ULPI DDR,6: Software programmable - reset to ULPI,7: Software programmable - reset to Serial" newline bitfld.long 0x4 4.--5. "PHYW,PHYW" "0: 8 bit wide data bus (Software non-programmable),1: 16 bit wide data bus (Software non-programmable),2: Reset to 8 bit wide data bus (Software..,3: Reset to 16 bit wide data bus (Software.." line.long 0x8 "HWHOST,Host Hardware Parameters" bitfld.long 0x8 1.--3. "NPORT,NPORT" "0,1,2,3,4,5,6,7" newline bitfld.long 0x8 0. "HC,HC" "0: Not supported,1: Supported" line.long 0xC "HWDEVICE,Device Hardware Parameters" hexmask.long.byte 0xC 1.--5. 1. "DEVEP,DEVEP" newline bitfld.long 0xC 0. "DC,DC" "0: Not supported,1: Supported" line.long 0x10 "HWTXBUF,TX Buffer Hardware Parameters" hexmask.long.byte 0x10 16.--23. 1. "TXCHANADD,TXCHANADD" newline hexmask.long.byte 0x10 0.--7. 1. "TXBURST,TXBURST" line.long 0x14 "HWRXBUF,RX Buffer Hardware Parameters" hexmask.long.byte 0x14 8.--15. 1. "RXADD,RXADD" newline hexmask.long.byte 0x14 0.--7. 1. "RXBURST,RXBURST" group.long 0x80++0x13 line.long 0x0 "GPTIMER0LD,General Purpose Timer #0 Load" hexmask.long.tbyte 0x0 0.--23. 1. "GPTLD,GPTLD" line.long 0x4 "GPTIMER0CTRL,General Purpose Timer #0 Controller" bitfld.long 0x4 31. "GPTRUN,GPTRUN" "0: Stop counting,1: Run" newline bitfld.long 0x4 30. "GPTRST,GPTRST" "0: No action,1: Load counter value from GPTLD bits in n_GPTIMER0LD" newline bitfld.long 0x4 24. "GPTMODE,GPTMODE" "0: One Shot Mode,1: Repeat Mode" newline hexmask.long.tbyte 0x4 0.--23. 1. "GPTCNT,GPTCNT" line.long 0x8 "GPTIMER1LD,General Purpose Timer #1 Load" hexmask.long.tbyte 0x8 0.--23. 1. "GPTLD,GPTLD" line.long 0xC "GPTIMER1CTRL,General Purpose Timer #1 Controller" bitfld.long 0xC 31. "GPTRUN,GPTRUN" "0: Stop counting,1: Run" newline bitfld.long 0xC 30. "GPTRST,GPTRST" "0: No action,1: Load counter value from GPTLD bits in.." newline bitfld.long 0xC 24. "GPTMODE,GPTMODE" "0: One Shot Mode,1: Repeat Mode" newline hexmask.long.tbyte 0xC 0.--23. 1. "GPTCNT,GPTCNT" line.long 0x10 "SBUSCFG,System Bus Config" bitfld.long 0x10 0.--2. "AHBBRST,AHBBRST" "0: Incremental burst of unspecified length only,1: INCR4 burst then single transfer,2: INCR8 burst INCR4 burst then single transfer,3: INCR16 burst INCR8 burst INCR4 burst then single..,?,5: INCR4 burst then incremental burst of..,6: INCR8 burst INCR4 burst then incremental burst..,7: INCR16 burst INCR8 burst INCR4 burst then.." rgroup.byte 0x100++0x0 line.byte 0x0 "CAPLENGTH,Capability Registers Length" hexmask.byte 0x0 0.--7. 1. "CAPLENGTH,CAPLENGTH" rgroup.word 0x102++0x1 line.word 0x0 "HCIVERSION,Host Controller Interface Version" hexmask.word 0x0 0.--15. 1. "HCIVERSION,HCIVERSION" rgroup.long 0x104++0x7 line.long 0x0 "HCSPARAMS,Host Controller Structural Parameters" hexmask.long.byte 0x0 24.--27. 1. "N_TT,N_TT" newline hexmask.long.byte 0x0 20.--23. 1. "N_PTT,N_PTT" newline bitfld.long 0x0 16. "PI,PI" "0,1" newline hexmask.long.byte 0x0 12.--15. 1. "N_CC,N_CC" newline hexmask.long.byte 0x0 8.--11. 1. "N_PCC,N_PCC" newline bitfld.long 0x0 4. "PPC,PPC" "0,1" newline hexmask.long.byte 0x0 0.--3. 1. "N_PORTS,N_PORTS" line.long 0x4 "HCCPARAMS,Host Controller Capability Parameters" hexmask.long.byte 0x4 8.--15. 1. "EECP,EECP" newline hexmask.long.byte 0x4 4.--7. 1. "IST,IST" newline bitfld.long 0x4 2. "ASP,ASP" "0,1" newline bitfld.long 0x4 1. "PFL,PFL" "0,1" newline bitfld.long 0x4 0. "ADC,ADC" "0,1" rgroup.word 0x120++0x1 line.word 0x0 "DCIVERSION,Device Controller Interface Version" hexmask.word 0x0 0.--15. 1. "DCIVERSION,DCIVERSION" rgroup.long 0x124++0x3 line.long 0x0 "DCCPARAMS,Device Controller Capability Parameters" bitfld.long 0x0 8. "HC,HC" "0,1" newline bitfld.long 0x0 7. "DC,DC" "0,1" newline hexmask.long.byte 0x0 0.--4. 1. "DEN,DEN" group.long 0x140++0xF line.long 0x0 "USBCMD,USB Command Register" hexmask.long.byte 0x0 16.--23. 1. "ITC,ITC" newline bitfld.long 0x0 15. "FS_2,FS_2" "0,1" newline bitfld.long 0x0 14. "ATDTW,ATDTW" "0,1" newline bitfld.long 0x0 13. "SUTW,SUTW" "0,1" newline bitfld.long 0x0 11. "ASPE,ASPE" "0,1" newline bitfld.long 0x0 8.--9. "ASP,ASP" "0,1,2,3" newline bitfld.long 0x0 6. "IAA,IAA" "0,1" newline bitfld.long 0x0 5. "ASE,ASE" "0: Do not process the Asynchronous Schedule.,1: Use the ASYNCLISTADDR register to access the.." newline bitfld.long 0x0 4. "PSE,PSE" "0: Do not process the Periodic Schedule,1: Use the PERIODICLISTBASE register to access the.." newline bitfld.long 0x0 2.--3. "FS_1,FS_1" "0,1,2,3" newline bitfld.long 0x0 1. "RST,RST" "0,1" newline bitfld.long 0x0 0. "RS,RS" "0,1" line.long 0x4 "USBSTS,USB Status Register" bitfld.long 0x4 25. "TI1,TI1" "0,1" newline bitfld.long 0x4 24. "TI0,TI0" "0,1" newline rbitfld.long 0x4 16. "NAKI,NAKI" "0,1" newline bitfld.long 0x4 15. "AS,AS" "0,1" newline bitfld.long 0x4 14. "PS,PS" "0,1" newline bitfld.long 0x4 13. "RCL,RCL" "0,1" newline bitfld.long 0x4 12. "HCH,HCH" "0,1" newline bitfld.long 0x4 10. "ULPII,ULPII" "0,1" newline bitfld.long 0x4 8. "SLI,SLI" "0,1" newline bitfld.long 0x4 7. "SRI,SRI" "0,1" newline bitfld.long 0x4 6. "URI,URI" "0,1" newline bitfld.long 0x4 5. "AAI,AAI" "0,1" newline bitfld.long 0x4 4. "SEI,SEI" "0,1" newline bitfld.long 0x4 3. "FRI,FRI" "0,1" newline bitfld.long 0x4 2. "PCI,PCI" "0,1" newline bitfld.long 0x4 1. "UEI,UEI" "0,1" newline bitfld.long 0x4 0. "UI,UI" "0,1" line.long 0x8 "USBINTR,Interrupt Enable Register" bitfld.long 0x8 25. "TIE1,TIE1" "0,1" newline bitfld.long 0x8 24. "TIE0,TIE0" "0,1" newline bitfld.long 0x8 19. "UPIE,UPIE" "0,1" newline bitfld.long 0x8 18. "UAIE,UAIE" "0,1" newline bitfld.long 0x8 16. "NAKE,NAKE" "0,1" newline bitfld.long 0x8 10. "ULPIE,ULPIE" "0,1" newline bitfld.long 0x8 8. "SLE,SLE" "0,1" newline bitfld.long 0x8 7. "SRE,SRE" "0,1" newline bitfld.long 0x8 6. "URE,URE" "0,1" newline bitfld.long 0x8 5. "AAE,AAE" "0,1" newline bitfld.long 0x8 4. "SEE,SEE" "0,1" newline bitfld.long 0x8 3. "FRE,FRE" "0,1" newline bitfld.long 0x8 2. "PCE,PCE" "0,1" newline bitfld.long 0x8 1. "UEE,UEE" "0,1" newline bitfld.long 0x8 0. "UE,UE" "0,1" line.long 0xC "FRINDEX,USB Frame Index" hexmask.long.word 0xC 0.--13. 1. "FRINDEX,FRINDEX" group.long 0x154++0x3 line.long 0x0 "DEVICEADDR,Device Address" hexmask.long.byte 0x0 25.--31. 1. "USBADR,USBADR" newline bitfld.long 0x0 24. "USBADRA,USBADRA" "0,1" group.long 0x154++0x7 line.long 0x0 "PERIODICLISTBASE,Frame List Base Address" hexmask.long.tbyte 0x0 12.--31. 1. "BASEADR,BASEADR" line.long 0x4 "ASYNCLISTADDR,Next Asynch. Address" hexmask.long 0x4 5.--31. 1. "ASYBASE,ASYBASE" group.long 0x158++0x3 line.long 0x0 "ENDPTLISTADDR,Endpoint List Address" hexmask.long.tbyte 0x0 11.--31. 1. "EPBASE,EPBASE" group.long 0x160++0x7 line.long 0x0 "BURSTSIZE,Programmable Burst Size" hexmask.long.word 0x0 8.--16. 1. "TXPBURST,TXPBURST" newline hexmask.long.byte 0x0 0.--7. 1. "RXPBURST,RXPBURST" line.long 0x4 "TXFILLTUNING,TX FIFO Fill Tuning" hexmask.long.byte 0x4 16.--21. 1. "TXFIFOTHRES,TXFIFOTHRES" newline hexmask.long.byte 0x4 8.--12. 1. "TXSCHHEALTH,TXSCHHEALTH" newline hexmask.long.byte 0x4 0.--7. 1. "TXSCHOH,TXSCHOH" group.long 0x178++0x7 line.long 0x0 "ENDPTNAK,Endpoint NAK" hexmask.long.byte 0x0 16.--23. 1. "EPTN,EPTN" newline hexmask.long.byte 0x0 0.--7. 1. "EPRN,EPRN" line.long 0x4 "ENDPTNAKEN,Endpoint NAK Enable" hexmask.long.byte 0x4 16.--23. 1. "EPTNE,EPTNE" newline hexmask.long.byte 0x4 0.--7. 1. "EPRNE,EPRNE" rgroup.long 0x180++0x3 line.long 0x0 "CONFIGFLAG,Configure Flag Register" bitfld.long 0x0 0. "CF,CF" "0: Port routing control logic default-routes each..,1: Port routing control logic default-routes all.." group.long 0x184++0x3 line.long 0x0 "PORTSC1,Port Status & Control" bitfld.long 0x0 30.--31. "PTS_1,PTS_1" "0,1,2,3" newline bitfld.long 0x0 29. "STS,STS" "0,1" newline bitfld.long 0x0 28. "PTW,PTW" "0: Select the 8-bit UTMI interface [60MHz],1: Select the 16-bit UTMI interface [30MHz]" newline bitfld.long 0x0 26.--27. "PSPD,PSPD" "0: Full Speed,1: Low Speed,2: High Speed,3: Undefined" newline bitfld.long 0x0 25. "PTS_2,PTS_2" "0,1" newline bitfld.long 0x0 24. "PFSC,PFSC" "0: Normal operation,1: Forced to full speed" newline bitfld.long 0x0 23. "PHCD,PHCD" "0: Enable PHY clock,1: Disable PHY clock" newline bitfld.long 0x0 22. "WKOC,WKOC" "0,1" newline bitfld.long 0x0 21. "WKDC,WKDC" "0,1" newline bitfld.long 0x0 20. "WKCN,WKCN" "0,1" newline hexmask.long.byte 0x0 16.--19. 1. "PTC,PTC" newline bitfld.long 0x0 14.--15. "PIC,PIC" "0: Port indicators are off,1: Amber,2: Green,3: Undefined" newline bitfld.long 0x0 13. "PO,PO" "0,1" newline bitfld.long 0x0 12. "PP,PP" "0,1" newline bitfld.long 0x0 10.--11. "LS,LS" "0: SE0,1: K-state,2: J-state,3: Undefined" newline rbitfld.long 0x0 9. "HSP,HSP" "0,1" newline bitfld.long 0x0 8. "PR,PR" "0,1" newline bitfld.long 0x0 7. "SUSP,SUSP" "0,1" newline bitfld.long 0x0 6. "FPR,FPR" "0,1" newline bitfld.long 0x0 5. "OCC,OCC" "0,1" newline rbitfld.long 0x0 4. "OCA,OCA" "0: This port does not have an over-current condition.,1: This port currently has an over-current condition" newline bitfld.long 0x0 3. "PEC,PEC" "0,1" newline bitfld.long 0x0 2. "PE,PE" "0,1" newline bitfld.long 0x0 1. "CSC,CSC" "0,1" newline rbitfld.long 0x0 0. "CCS,CCS" "0,1" group.long 0x1A4++0x13 line.long 0x0 "OTGSC,On-The-Go Status & control" bitfld.long 0x0 30. "DPIE,DPIE" "0,1" newline bitfld.long 0x0 29. "EN_1MS,EN_1MS" "0,1" newline bitfld.long 0x0 28. "BSEIE,BSEIE" "0,1" newline bitfld.long 0x0 27. "BSVIE,BSVIE" "0,1" newline bitfld.long 0x0 26. "ASVIE,ASVIE" "0,1" newline bitfld.long 0x0 25. "AVVIE,AVVIE" "0,1" newline bitfld.long 0x0 24. "IDIE,IDIE" "0,1" newline bitfld.long 0x0 22. "DPIS,DPIS" "0,1" newline bitfld.long 0x0 21. "STATUS_1MS,STATUS_1MS" "0,1" newline bitfld.long 0x0 20. "BSEIS,BSEIS" "0,1" newline bitfld.long 0x0 19. "BSVIS,BSVIS" "0,1" newline bitfld.long 0x0 18. "ASVIS,ASVIS" "0,1" newline bitfld.long 0x0 17. "AVVIS,AVVIS" "0,1" newline bitfld.long 0x0 16. "IDIS,IDIS" "0,1" newline rbitfld.long 0x0 14. "DPS,DPS" "0,1" newline rbitfld.long 0x0 13. "TOG_1MS,TOG_1MS" "0,1" newline rbitfld.long 0x0 12. "BSE,BSE" "0,1" newline rbitfld.long 0x0 11. "BSV,BSV" "0,1" newline rbitfld.long 0x0 10. "ASV,ASV" "0,1" newline rbitfld.long 0x0 9. "AVV,AVV" "0,1" newline rbitfld.long 0x0 8. "ID,ID" "0,1" newline bitfld.long 0x0 5. "IDPU,IDPU" "0,1" newline bitfld.long 0x0 4. "DP,DP" "0,1" newline bitfld.long 0x0 3. "OT,OT" "0,1" newline bitfld.long 0x0 1. "VC,VC" "0,1" newline bitfld.long 0x0 0. "VD,VD" "0,1" line.long 0x4 "USBMODE,USB Device Mode" bitfld.long 0x4 4. "SDIS,SDIS" "0,1" newline bitfld.long 0x4 3. "SLOM,SLOM" "0: Setup Lockouts On (default);,1: Setup Lockouts Off" newline bitfld.long 0x4 2. "ES,ES" "0: Little Endian [Default],1: Big Endian" newline bitfld.long 0x4 0.--1. "CM,CM" "0: Idle [Default for combination host/device],?,2: Device Controller [Default for device only..,3: Host Controller [Default for host only controller]" line.long 0x8 "ENDPTSETUPSTAT,Endpoint Setup Status" hexmask.long.word 0x8 0.--15. 1. "ENDPTSETUPSTAT,ENDPTSETUPSTAT" line.long 0xC "ENDPTPRIME,Endpoint Prime" hexmask.long.byte 0xC 16.--23. 1. "PETB,PETB" newline hexmask.long.byte 0xC 0.--7. 1. "PERB,PERB" line.long 0x10 "ENDPTFLUSH,Endpoint Flush" hexmask.long.byte 0x10 16.--23. 1. "FETB,FETB" newline hexmask.long.byte 0x10 0.--7. 1. "FERB,FERB" rgroup.long 0x1B8++0x3 line.long 0x0 "ENDPTSTAT,Endpoint Status" hexmask.long.byte 0x0 16.--23. 1. "ETBR,ETBR" newline hexmask.long.byte 0x0 0.--7. 1. "ERBR,ERBR" group.long 0x1BC++0x23 line.long 0x0 "ENDPTCOMPLETE,Endpoint Complete" hexmask.long.byte 0x0 16.--23. 1. "ETCE,ETCE" newline hexmask.long.byte 0x0 0.--7. 1. "ERCE,ERCE" line.long 0x4 "ENDPTCTRL0,Endpoint Control0" bitfld.long 0x4 23. "TXE,TXE" "0,1" newline bitfld.long 0x4 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x4 16. "TXS,TXS" "0,1" newline bitfld.long 0x4 7. "RXE,RXE" "0,1" newline bitfld.long 0x4 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x4 0. "RXS,RXS" "0,1" line.long 0x8 "ENDPTCTRL1,Endpoint Control 1" bitfld.long 0x8 23. "TXE,TXE" "0,1" newline bitfld.long 0x8 22. "TXR,TXR" "0,1" newline bitfld.long 0x8 21. "TXI,TXI" "0,1" newline bitfld.long 0x8 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x8 17. "TXD,TXD" "0,1" newline bitfld.long 0x8 16. "TXS,TXS" "0,1" newline bitfld.long 0x8 7. "RXE,RXE" "0,1" newline bitfld.long 0x8 6. "RXR,RXR" "0,1" newline bitfld.long 0x8 5. "RXI,RXI" "0,1" newline bitfld.long 0x8 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x8 1. "RXD,RXD" "0,1" newline bitfld.long 0x8 0. "RXS,RXS" "0,1" line.long 0xC "ENDPTCTRL2,Endpoint Control 2" bitfld.long 0xC 23. "TXE,TXE" "0,1" newline bitfld.long 0xC 22. "TXR,TXR" "0,1" newline bitfld.long 0xC 21. "TXI,TXI" "0,1" newline bitfld.long 0xC 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0xC 17. "TXD,TXD" "0,1" newline bitfld.long 0xC 16. "TXS,TXS" "0,1" newline bitfld.long 0xC 7. "RXE,RXE" "0,1" newline bitfld.long 0xC 6. "RXR,RXR" "0,1" newline bitfld.long 0xC 5. "RXI,RXI" "0,1" newline bitfld.long 0xC 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0xC 1. "RXD,RXD" "0,1" newline bitfld.long 0xC 0. "RXS,RXS" "0,1" line.long 0x10 "ENDPTCTRL3,Endpoint Control 3" bitfld.long 0x10 23. "TXE,TXE" "0,1" newline bitfld.long 0x10 22. "TXR,TXR" "0,1" newline bitfld.long 0x10 21. "TXI,TXI" "0,1" newline bitfld.long 0x10 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x10 17. "TXD,TXD" "0,1" newline bitfld.long 0x10 16. "TXS,TXS" "0,1" newline bitfld.long 0x10 7. "RXE,RXE" "0,1" newline bitfld.long 0x10 6. "RXR,RXR" "0,1" newline bitfld.long 0x10 5. "RXI,RXI" "0,1" newline bitfld.long 0x10 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x10 1. "RXD,RXD" "0,1" newline bitfld.long 0x10 0. "RXS,RXS" "0,1" line.long 0x14 "ENDPTCTRL4,Endpoint Control 4" bitfld.long 0x14 23. "TXE,TXE" "0,1" newline bitfld.long 0x14 22. "TXR,TXR" "0,1" newline bitfld.long 0x14 21. "TXI,TXI" "0,1" newline bitfld.long 0x14 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x14 17. "TXD,TXD" "0,1" newline bitfld.long 0x14 16. "TXS,TXS" "0,1" newline bitfld.long 0x14 7. "RXE,RXE" "0,1" newline bitfld.long 0x14 6. "RXR,RXR" "0,1" newline bitfld.long 0x14 5. "RXI,RXI" "0,1" newline bitfld.long 0x14 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x14 1. "RXD,RXD" "0,1" newline bitfld.long 0x14 0. "RXS,RXS" "0,1" line.long 0x18 "ENDPTCTRL5,Endpoint Control 5" bitfld.long 0x18 23. "TXE,TXE" "0,1" newline bitfld.long 0x18 22. "TXR,TXR" "0,1" newline bitfld.long 0x18 21. "TXI,TXI" "0,1" newline bitfld.long 0x18 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x18 17. "TXD,TXD" "0,1" newline bitfld.long 0x18 16. "TXS,TXS" "0,1" newline bitfld.long 0x18 7. "RXE,RXE" "0,1" newline bitfld.long 0x18 6. "RXR,RXR" "0,1" newline bitfld.long 0x18 5. "RXI,RXI" "0,1" newline bitfld.long 0x18 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x18 1. "RXD,RXD" "0,1" newline bitfld.long 0x18 0. "RXS,RXS" "0,1" line.long 0x1C "ENDPTCTRL6,Endpoint Control 6" bitfld.long 0x1C 23. "TXE,TXE" "0,1" newline bitfld.long 0x1C 22. "TXR,TXR" "0,1" newline bitfld.long 0x1C 21. "TXI,TXI" "0,1" newline bitfld.long 0x1C 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x1C 17. "TXD,TXD" "0,1" newline bitfld.long 0x1C 16. "TXS,TXS" "0,1" newline bitfld.long 0x1C 7. "RXE,RXE" "0,1" newline bitfld.long 0x1C 6. "RXR,RXR" "0,1" newline bitfld.long 0x1C 5. "RXI,RXI" "0,1" newline bitfld.long 0x1C 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x1C 1. "RXD,RXD" "0,1" newline bitfld.long 0x1C 0. "RXS,RXS" "0,1" line.long 0x20 "ENDPTCTRL7,Endpoint Control 7" bitfld.long 0x20 23. "TXE,TXE" "0,1" newline bitfld.long 0x20 22. "TXR,TXR" "0,1" newline bitfld.long 0x20 21. "TXI,TXI" "0,1" newline bitfld.long 0x20 18.--19. "TXT,TXT" "0,1,2,3" newline bitfld.long 0x20 17. "TXD,TXD" "0,1" newline bitfld.long 0x20 16. "TXS,TXS" "0,1" newline bitfld.long 0x20 7. "RXE,RXE" "0,1" newline bitfld.long 0x20 6. "RXR,RXR" "0,1" newline bitfld.long 0x20 5. "RXI,RXI" "0,1" newline bitfld.long 0x20 2.--3. "RXT,RXT" "0,1,2,3" newline bitfld.long 0x20 1. "RXD,RXD" "0,1" newline bitfld.long 0x20 0. "RXS,RXS" "0,1" tree.end tree.end tree "USBHSDCD" base ad:0x0 tree "USBHSDCD1" base ad:0x40434800 group.long 0x0++0x7 line.long 0x0 "CONTROL,Control register" bitfld.long 0x0 25. "SR,Software Reset" "0: Do not perform a software reset.,1: Perform a software reset." bitfld.long 0x0 24. "START,Start Change Detection Sequence" "0: Do not start the sequence. Writes of this value..,1: Initiate the charger detection sequence. If the.." newline bitfld.long 0x0 17. "BC12,BC12" "0: Compatible with BC1.1 (default),1: Compatible with BC1.2" bitfld.long 0x0 16. "IE,Interrupt Enable" "0: Disable interrupts to the system.,1: Enable interrupts to the system." newline rbitfld.long 0x0 8. "IF,Interrupt Flag" "0: No interrupt is pending.,1: An interrupt is pending." bitfld.long 0x0 0. "IACK,Interrupt Acknowledge" "0: Do not clear the interrupt.,1: Clear the IF bit (interrupt flag)." line.long 0x4 "CLOCK,Clock register" hexmask.long.word 0x4 2.--11. 1. "CLOCK_SPEED,Numerical Value of Clock Speed in Binary" bitfld.long 0x4 0. "CLOCK_UNIT,Unit of Measurement Encoding for Clock Speed" "0: kHz Speed (between 1 kHz and 1023 kHz),1: MHz Speed (between 1 MHz and 1023 MHz)" rgroup.long 0x8++0x3 line.long 0x0 "STATUS,Status register" bitfld.long 0x0 22. "ACTIVE,Active Status Indicator" "0: The sequence is not running.,1: The sequence is running." bitfld.long 0x0 21. "TO,Timeout Flag" "0: The detection sequence has not been running for..,1: It has been over 1 s since the data pin contact.." newline bitfld.long 0x0 20. "ERR,Error Flag" "0: No sequence errors.,1: Error in the detection sequence. See the.." bitfld.long 0x0 18.--19. "SEQ_STAT,Charger Detection Sequence Status" "0: The module is either not enabled or the module..,1: Data pin contact detection is complete.,2: Charging port detection is complete.,3: Charger type detection is complete." newline bitfld.long 0x0 16.--17. "SEQ_RES,Charger Detection Sequence Results" "0: No results to report.,1: Attached to an SDP. Must comply with USB 2.0 by..,2: Attached to a charging port. The exact meaning..,3: Attached to a DCP." group.long 0xC++0xF line.long 0x0 "SIGNAL_OVERRIDE,Signal Override Register" bitfld.long 0x0 0.--1. "PS,Phase Selection" "0: No overrides. Bit field must remain at this..,?,2: Enables VDP_SRC voltage source for the USB_DP..,?" line.long 0x4 "TIMER0,TIMER0 register" hexmask.long.word 0x4 16.--25. 1. "TSEQ_INIT,Sequence Initiation Time" hexmask.long.word 0x4 0.--11. 1. "TUNITCON,Unit Connection Timer Elapse (in ms)" line.long 0x8 "TIMER1,TIMER1 register" hexmask.long.word 0x8 16.--25. 1. "TDCD_DBNC,Time Period to Debounce D+ Signal" hexmask.long.word 0x8 0.--9. 1. "TVDPSRC_ON,Time Period Comparator Enabled" line.long 0xC "TIMER2_BC11,TIMER2_BC11 register" hexmask.long.word 0xC 16.--25. 1. "TVDPSRC_CON,Time Period Before Enabling D+ Pullup" hexmask.long.byte 0xC 0.--3. 1. "CHECK_DM,Time Before Check of D- Line" group.long 0x18++0x3 line.long 0x0 "TIMER2_BC12,TIMER2_BC12 register" hexmask.long.word 0x0 16.--25. 1. "TWAIT_AFTER_PRD,TWAIT_AFTER_PRD" hexmask.long.word 0x0 0.--9. 1. "TVDMSRC_ON,TVDMSRC_ON" tree.end tree "USBHSDCD2" base ad:0x40438800 group.long 0x0++0x7 line.long 0x0 "CONTROL,Control register" bitfld.long 0x0 25. "SR,Software Reset" "0: Do not perform a software reset.,1: Perform a software reset." bitfld.long 0x0 24. "START,Start Change Detection Sequence" "0: Do not start the sequence. Writes of this value..,1: Initiate the charger detection sequence. If the.." newline bitfld.long 0x0 17. "BC12,BC12" "0: Compatible with BC1.1 (default),1: Compatible with BC1.2" bitfld.long 0x0 16. "IE,Interrupt Enable" "0: Disable interrupts to the system.,1: Enable interrupts to the system." newline rbitfld.long 0x0 8. "IF,Interrupt Flag" "0: No interrupt is pending.,1: An interrupt is pending." bitfld.long 0x0 0. "IACK,Interrupt Acknowledge" "0: Do not clear the interrupt.,1: Clear the IF bit (interrupt flag)." line.long 0x4 "CLOCK,Clock register" hexmask.long.word 0x4 2.--11. 1. "CLOCK_SPEED,Numerical Value of Clock Speed in Binary" bitfld.long 0x4 0. "CLOCK_UNIT,Unit of Measurement Encoding for Clock Speed" "0: kHz Speed (between 1 kHz and 1023 kHz),1: MHz Speed (between 1 MHz and 1023 MHz)" rgroup.long 0x8++0x3 line.long 0x0 "STATUS,Status register" bitfld.long 0x0 22. "ACTIVE,Active Status Indicator" "0: The sequence is not running.,1: The sequence is running." bitfld.long 0x0 21. "TO,Timeout Flag" "0: The detection sequence has not been running for..,1: It has been over 1 s since the data pin contact.." newline bitfld.long 0x0 20. "ERR,Error Flag" "0: No sequence errors.,1: Error in the detection sequence. See the.." bitfld.long 0x0 18.--19. "SEQ_STAT,Charger Detection Sequence Status" "0: The module is either not enabled or the module..,1: Data pin contact detection is complete.,2: Charging port detection is complete.,3: Charger type detection is complete." newline bitfld.long 0x0 16.--17. "SEQ_RES,Charger Detection Sequence Results" "0: No results to report.,1: Attached to an SDP. Must comply with USB 2.0 by..,2: Attached to a charging port. The exact meaning..,3: Attached to a DCP." group.long 0xC++0xF line.long 0x0 "SIGNAL_OVERRIDE,Signal Override Register" bitfld.long 0x0 0.--1. "PS,Phase Selection" "0: No overrides. Bit field must remain at this..,?,2: Enables VDP_SRC voltage source for the USB_DP..,?" line.long 0x4 "TIMER0,TIMER0 register" hexmask.long.word 0x4 16.--25. 1. "TSEQ_INIT,Sequence Initiation Time" hexmask.long.word 0x4 0.--11. 1. "TUNITCON,Unit Connection Timer Elapse (in ms)" line.long 0x8 "TIMER1,TIMER1 register" hexmask.long.word 0x8 16.--25. 1. "TDCD_DBNC,Time Period to Debounce D+ Signal" hexmask.long.word 0x8 0.--9. 1. "TVDPSRC_ON,Time Period Comparator Enabled" line.long 0xC "TIMER2_BC11,TIMER2_BC11 register" hexmask.long.word 0xC 16.--25. 1. "TVDPSRC_CON,Time Period Before Enabling D+ Pullup" hexmask.long.byte 0xC 0.--3. 1. "CHECK_DM,Time Before Check of D- Line" group.long 0x18++0x3 line.long 0x0 "TIMER2_BC12,TIMER2_BC12 register" hexmask.long.word 0x0 16.--25. 1. "TWAIT_AFTER_PRD,TWAIT_AFTER_PRD" hexmask.long.word 0x0 0.--9. 1. "TVDMSRC_ON,TVDMSRC_ON" tree.end tree.end tree "USBNC" base ad:0x0 tree "USBNC_OTG1" base ad:0x40430200 group.long 0x0++0x7 line.long 0x0 "CTRL1,USB OTG Control 1 Register" rbitfld.long 0x0 31. "WIR,WIR" "0: No wake-up interrupt request received,1: Wake-up Interrupt Request received" bitfld.long 0x0 29. "WKUP_DPDM_EN,Wake-up on DPDM change enable" "0: DPDM changes wake-up to be disabled only when..,1: (Default) DPDM changes wake-up to be enabled it.." newline bitfld.long 0x0 17. "WKUP_VBUS_EN,WKUP_VBUS_EN" "0: Disable,1: Enable" bitfld.long 0x0 16. "WKUP_ID_EN,WKUP_ID_EN" "0: Disable,1: Enable" newline bitfld.long 0x0 15. "WKUP_SW,WKUP_SW" "0: Inactive,1: Force wake-up" bitfld.long 0x0 14. "WKUP_SW_EN,WKUP_SW_EN" "0: Disable,1: Enable" newline bitfld.long 0x0 10. "WIE,WIE" "0: Interrupt Disabled,1: Interrupt Enabled" bitfld.long 0x0 9. "PWR_POL,PWR_POL" "0: PMIC Power Pin is Low active.,1: PMIC Power Pin is High active." newline bitfld.long 0x0 8. "OVER_CUR_POL,OVER_CUR_POL" "0: High active (high on this signal represents an..,1: Low active (low on this signal represents an.." bitfld.long 0x0 7. "OVER_CUR_DIS,OVER_CUR_DIS" "0: Enables overcurrent detection,1: Disables overcurrent detection" line.long 0x4 "CTRL2,USB OTG Control 2 Register" eventfld.long 0x4 31. "UTMI_CLK_VLD,UTMI_CLK_VLD" "0: Default,?" bitfld.long 0x4 3. "LOWSPEED_EN,LOWSPEED_EN" "0: Default,?" newline bitfld.long 0x4 2. "AUTURESUME_EN,Auto Resume Enable" "0: Default,?" bitfld.long 0x4 0.--1. "VBUS_SOURCE_SEL,VBUS_SOURCE_SEL" "0: vbus_valid,1: sess_valid,2: sess_valid,3: sess_valid" group.long 0x10++0x3 line.long 0x0 "HSIC_CTRL,USB Host HSIC Control Register" rbitfld.long 0x0 31. "CLK_VLD,CLK_VLD" "0: Invalid,1: Valid" bitfld.long 0x0 12. "HSIC_EN,HSIC_EN" "0: Disabled,1: Enabled" newline bitfld.long 0x0 11. "HSIC_CLK_ON,HSIC_CLK_ON" "0: Inactive,1: Active" tree.end tree "USBNC_OTG2" base ad:0x4042C200 group.long 0x0++0x7 line.long 0x0 "CTRL1,USB OTG Control 1 Register" rbitfld.long 0x0 31. "WIR,WIR" "0: No wake-up interrupt request received,1: Wake-up Interrupt Request received" bitfld.long 0x0 29. "WKUP_DPDM_EN,Wake-up on DPDM change enable" "0: DPDM changes wake-up to be disabled only when..,1: (Default) DPDM changes wake-up to be enabled it.." newline bitfld.long 0x0 17. "WKUP_VBUS_EN,WKUP_VBUS_EN" "0: Disable,1: Enable" bitfld.long 0x0 16. "WKUP_ID_EN,WKUP_ID_EN" "0: Disable,1: Enable" newline bitfld.long 0x0 15. "WKUP_SW,WKUP_SW" "0: Inactive,1: Force wake-up" bitfld.long 0x0 14. "WKUP_SW_EN,WKUP_SW_EN" "0: Disable,1: Enable" newline bitfld.long 0x0 10. "WIE,WIE" "0: Interrupt Disabled,1: Interrupt Enabled" bitfld.long 0x0 9. "PWR_POL,PWR_POL" "0: PMIC Power Pin is Low active.,1: PMIC Power Pin is High active." newline bitfld.long 0x0 8. "OVER_CUR_POL,OVER_CUR_POL" "0: High active (high on this signal represents an..,1: Low active (low on this signal represents an.." bitfld.long 0x0 7. "OVER_CUR_DIS,OVER_CUR_DIS" "0: Enables overcurrent detection,1: Disables overcurrent detection" line.long 0x4 "CTRL2,USB OTG Control 2 Register" eventfld.long 0x4 31. "UTMI_CLK_VLD,UTMI_CLK_VLD" "0: Default,?" bitfld.long 0x4 3. "LOWSPEED_EN,LOWSPEED_EN" "0: Default,?" newline bitfld.long 0x4 2. "AUTURESUME_EN,Auto Resume Enable" "0: Default,?" bitfld.long 0x4 0.--1. "VBUS_SOURCE_SEL,VBUS_SOURCE_SEL" "0: vbus_valid,1: sess_valid,2: sess_valid,3: sess_valid" group.long 0x10++0x3 line.long 0x0 "HSIC_CTRL,USB Host HSIC Control Register" rbitfld.long 0x0 31. "CLK_VLD,CLK_VLD" "0: Invalid,1: Valid" bitfld.long 0x0 12. "HSIC_EN,HSIC_EN" "0: Disabled,1: Enabled" newline bitfld.long 0x0 11. "HSIC_CLK_ON,HSIC_CLK_ON" "0: Inactive,1: Active" tree.end tree.end tree "USBPHY" base ad:0x0 tree "USBPHY1" base ad:0x40434000 group.long 0x0++0x43 line.long 0x0 "PWD,USB PHY Power-Down Register" bitfld.long 0x0 20. "RXPWDRX,RXPWDRX" "0: Normal operation,1: Power-down the entire USB PHY receiver block.." newline bitfld.long 0x0 19. "RXPWDDIFF,RXPWDDIFF" "0: Normal operation.,1: Power-down the USB high-speed differential.." newline bitfld.long 0x0 18. "RXPWD1PT1,RXPWD1PT1" "0: Normal operation,1: Power-down the USB full-speed differential.." newline bitfld.long 0x0 17. "RXPWDENV,RXPWDENV" "0: Normal operation.,1: Power-down the USB high-speed receiver envelope.." newline bitfld.long 0x0 12. "TXPWDV2I,TXPWDV2I" "0: Normal operation.,1: Power-down the USB PHY transmit V-to-I converter.." newline bitfld.long 0x0 11. "TXPWDIBIAS,TXPWDIBIAS" "0: Normal operation,1: Power-down the USB PHY current bias block for.." newline bitfld.long 0x0 10. "TXPWDFS,TXPWDFS" "0: Normal operation.,1: Power-down the USB full-speed drivers. This.." line.long 0x4 "PWD_SET,USB PHY Power-Down Register" bitfld.long 0x4 20. "RXPWDRX,RXPWDRX" "0,1" newline bitfld.long 0x4 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline bitfld.long 0x4 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline bitfld.long 0x4 17. "RXPWDENV,RXPWDENV" "0,1" newline bitfld.long 0x4 12. "TXPWDV2I,TXPWDV2I" "0,1" newline bitfld.long 0x4 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline bitfld.long 0x4 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0x8 "PWD_CLR,USB PHY Power-Down Register" eventfld.long 0x8 20. "RXPWDRX,RXPWDRX" "0,1" newline eventfld.long 0x8 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline eventfld.long 0x8 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline eventfld.long 0x8 17. "RXPWDENV,RXPWDENV" "0,1" newline eventfld.long 0x8 12. "TXPWDV2I,TXPWDV2I" "0,1" newline eventfld.long 0x8 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline eventfld.long 0x8 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0xC "PWD_TOG,USB PHY Power-Down Register" bitfld.long 0xC 20. "RXPWDRX,RXPWDRX" "0,1" newline bitfld.long 0xC 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline bitfld.long 0xC 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline bitfld.long 0xC 17. "RXPWDENV,RXPWDENV" "0,1" newline bitfld.long 0xC 12. "TXPWDV2I,TXPWDV2I" "0,1" newline bitfld.long 0xC 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline bitfld.long 0xC 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0x10 "TX,USB PHY Transmitter Control Register" hexmask.long.byte 0x10 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x10 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x10 0.--3. 1. "D_CAL,D_CAL" line.long 0x14 "TX_SET,USB PHY Transmitter Control Register" hexmask.long.byte 0x14 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x14 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x14 0.--3. 1. "D_CAL,D_CAL" line.long 0x18 "TX_CLR,USB PHY Transmitter Control Register" hexmask.long.byte 0x18 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x18 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x18 0.--3. 1. "D_CAL,D_CAL" line.long 0x1C "TX_TOG,USB PHY Transmitter Control Register" hexmask.long.byte 0x1C 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x1C 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x1C 0.--3. 1. "D_CAL,D_CAL" line.long 0x20 "RX,USB PHY Receiver Control Register" bitfld.long 0x20 22. "RXDBYPASS,RXDBYPASS" "0: Normal operation.,1: Use the output of the USB_DP single-ended.." newline bitfld.long 0x20 4.--6. "DISCONADJ,DISCONADJ" "0: Trip-Level Voltage is 0.56875 V,1: Trip-Level Voltage is 0.55000 V,2: Trip-Level Voltage is 0.58125 V,3: Trip-Level Voltage is 0.60000 V,?,?,?,?" newline bitfld.long 0x20 0.--2. "ENVADJ,ENVADJ" "0: Trip-Level Voltage is 0.1000 V,1: Trip-Level Voltage is 0.1125 V,2: Trip-Level Voltage is 0.1250 V,3: Trip-Level Voltage is 0.0875 V,?,?,?,?" line.long 0x24 "RX_SET,USB PHY Receiver Control Register" bitfld.long 0x24 22. "RXDBYPASS,RXDBYPASS" "0,1" newline bitfld.long 0x24 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x24 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x28 "RX_CLR,USB PHY Receiver Control Register" eventfld.long 0x28 22. "RXDBYPASS,RXDBYPASS" "0,1" newline eventfld.long 0x28 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline eventfld.long 0x28 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x2C "RX_TOG,USB PHY Receiver Control Register" bitfld.long 0x2C 22. "RXDBYPASS,RXDBYPASS" "0,1" newline bitfld.long 0x2C 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x2C 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x30 "CTRL,USB PHY General Control Register" bitfld.long 0x30 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x30 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x30 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x30 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x30 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x30 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x30 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x30 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x30 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x30 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x30 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x30 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x30 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x30 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x30 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x30 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x30 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x30 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x30 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x30 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x30 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x30 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x30 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x30 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x30 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0: Disables 200kohm pullup resistors on DP and DN..,1: Enables 200kohm pullup resistors on DP and DN pins" newline bitfld.long 0x30 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x30 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x30 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x30 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x34 "CTRL_SET,USB PHY General Control Register" bitfld.long 0x34 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x34 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x34 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x34 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x34 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x34 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x34 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x34 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x34 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x34 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x34 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x34 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x34 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x34 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x34 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x34 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x34 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x34 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x34 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x34 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x34 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x34 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x34 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x34 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x34 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline bitfld.long 0x34 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x34 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x34 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x34 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x38 "CTRL_CLR,USB PHY General Control Register" eventfld.long 0x38 31. "SFTRST,SFTRST" "0,1" newline eventfld.long 0x38 30. "CLKGATE,CLKGATE" "0,1" newline eventfld.long 0x38 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline eventfld.long 0x38 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline eventfld.long 0x38 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline eventfld.long 0x38 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline eventfld.long 0x38 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline eventfld.long 0x38 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline eventfld.long 0x38 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline eventfld.long 0x38 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline eventfld.long 0x38 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline eventfld.long 0x38 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline eventfld.long 0x38 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline eventfld.long 0x38 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline eventfld.long 0x38 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline eventfld.long 0x38 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline eventfld.long 0x38 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline eventfld.long 0x38 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline eventfld.long 0x38 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline eventfld.long 0x38 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline eventfld.long 0x38 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline eventfld.long 0x38 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline eventfld.long 0x38 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline eventfld.long 0x38 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline eventfld.long 0x38 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline eventfld.long 0x38 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline eventfld.long 0x38 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline eventfld.long 0x38 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline eventfld.long 0x38 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x3C "CTRL_TOG,USB PHY General Control Register" bitfld.long 0x3C 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x3C 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x3C 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x3C 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x3C 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x3C 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x3C 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x3C 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x3C 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x3C 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x3C 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x3C 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x3C 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x3C 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x3C 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x3C 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x3C 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x3C 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x3C 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x3C 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x3C 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x3C 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x3C 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x3C 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x3C 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline bitfld.long 0x3C 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x3C 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x3C 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x3C 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x40 "STATUS,USB PHY Status Register" rbitfld.long 0x40 10. "RESUME_STATUS,RESUME_STATUS" "0,1" newline bitfld.long 0x40 8. "OTGID_STATUS,OTGID_STATUS" "0,1" newline rbitfld.long 0x40 6. "DEVPLUGIN_STATUS,Status indicator for non-standard resistive plugged-in detection" "0: No attachment to a USB host is detected,1: Cable attachment to a USB host is detected" newline rbitfld.long 0x40 3. "HOSTDISCONDETECT_STATUS,HOSTDISCONDETECT_STATUS" "0: USB cable disconnect has not been detected at..,1: USB cable disconnect has been detected at the.." group.long 0x50++0xF line.long 0x0 "DEBUG,USB PHY Debug Register" bitfld.long 0x0 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0x0 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x0 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0x0 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x0 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0x0 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0x0 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x0 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x0 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0x0 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0x4 "DEBUG_SET,USB PHY Debug Register" bitfld.long 0x4 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0x4 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x4 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0x4 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x4 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0x4 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0x4 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x4 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x4 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0x4 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0x8 "DEBUG_CLR,USB PHY Debug Register" eventfld.long 0x8 30. "CLKGATE,CLKGATE" "0,1" newline eventfld.long 0x8 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x8 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline eventfld.long 0x8 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x8 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline eventfld.long 0x8 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline eventfld.long 0x8 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline eventfld.long 0x8 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline eventfld.long 0x8 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline eventfld.long 0x8 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0xC "DEBUG_TOG,USB PHY Debug Register" bitfld.long 0xC 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0xC 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0xC 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0xC 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0xC 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0xC 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0xC 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0xC 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0xC 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0xC 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" rgroup.long 0x60++0x3 line.long 0x0 "DEBUG0_STATUS,UTMI Debug Status Register 0" hexmask.long.byte 0x0 26.--31. 1. "SQUELCH_COUNT,SQUELCH_COUNT" newline hexmask.long.word 0x0 16.--25. 1. "UTMI_RXERROR_FAIL_COUNT,UTMI_RXERROR_FAIL_COUNT" newline hexmask.long.word 0x0 0.--15. 1. "LOOP_BACK_FAIL_COUNT,LOOP_BACK_FAIL_COUNT" group.long 0x70++0xF line.long 0x0 "DEBUG1,UTMI Debug Status Register 1" bitfld.long 0x0 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0x0 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0x0 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0x0 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0x0 13.--14. "ENTAILADJVD,ENTAILADJVD" "0: Delay is nominal,1: Delay is +20%,2: Delay is -20%,3: Delay is -40%" line.long 0x4 "DEBUG1_SET,UTMI Debug Status Register 1" bitfld.long 0x4 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0x4 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0x4 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0x4 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0x4 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" line.long 0x8 "DEBUG1_CLR,UTMI Debug Status Register 1" eventfld.long 0x8 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline eventfld.long 0x8 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline eventfld.long 0x8 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline eventfld.long 0x8 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline eventfld.long 0x8 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" line.long 0xC "DEBUG1_TOG,UTMI Debug Status Register 1" bitfld.long 0xC 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0xC 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0xC 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0xC 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0xC 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" rgroup.long 0x80++0x3 line.long 0x0 "VERSION,UTMI RTL Version" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,MAJOR" newline hexmask.long.byte 0x0 16.--23. 1. "MINOR,MINOR" newline hexmask.long.word 0x0 0.--15. 1. "STEP,STEP" group.long 0xA0++0xF line.long 0x0 "PLL_SIC,USB PHY PLL Control/Status Register" rbitfld.long 0x0 31. "PLL_LOCK,PLL_LOCK" "0: PLL is not currently locked,1: PLL is currently locked" newline bitfld.long 0x0 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0: Divide by 13,1: Divide by 15,2: Divide by 16,3: Divide by 20,4: Divide by 22,5: Divide by 25,6: Divide by 30,7: Divide by 240" newline bitfld.long 0x0 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0x0 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0x0 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0: Selects PLL_POWER to control the reference bias,1: Selects REFBIAS_PWD to control the reference bias." newline bitfld.long 0x0 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0x0 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0x0 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0x0 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0x0 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0x4 "PLL_SIC_SET,USB PHY PLL Control/Status Register" rbitfld.long 0x4 31. "PLL_LOCK,PLL_LOCK" "0,1" newline bitfld.long 0x4 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0x4 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0x4 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline bitfld.long 0x4 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0x4 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0x4 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0x4 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0x4 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0x8 "PLL_SIC_CLR,USB PHY PLL Control/Status Register" eventfld.long 0x8 31. "PLL_LOCK,PLL_LOCK" "0,1" newline eventfld.long 0x8 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline eventfld.long 0x8 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline eventfld.long 0x8 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline eventfld.long 0x8 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline eventfld.long 0x8 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline eventfld.long 0x8 12. "PLL_POWER,PLL_POWER" "0,1" newline eventfld.long 0x8 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline eventfld.long 0x8 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0xC "PLL_SIC_TOG,USB PHY PLL Control/Status Register" rbitfld.long 0xC 31. "PLL_LOCK,PLL_LOCK" "0,1" newline bitfld.long 0xC 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0xC 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0xC 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline bitfld.long 0xC 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0xC 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0xC 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0xC 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0xC 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" group.long 0xC0++0xF line.long 0x0 "USB1_VBUS_DETECT,USB PHY VBUS Detect Control Register" bitfld.long 0x0 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0: Disable resistive charger detection resistors on..,1: Enable resistive charger detection resistors on.." newline bitfld.long 0x0 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0: VBUS discharge resistor is disabled (Default),1: VBUS discharge resistor is enabled" newline bitfld.long 0x0 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0: Powers down the VBUS_VALID comparator,1: Enables the SESS_VALID comparator (default),2: Enables the 3Vdetect (default),?,?,?,?,?" newline bitfld.long 0x0 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0: Use the VBUS_VALID comparator for VBUS_VALID..,1: Use the Session End comparator for VBUS_VALID.." newline bitfld.long 0x0 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0x0 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0x0 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0: Use the VBUS_VALID comparator results for signal..,1: Use the Session Valid comparator results for..,2: Use the Session Valid comparator results for..,?" newline bitfld.long 0x0 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0: Use the VBUS_VALID comparator results for signal..,1: Use the VBUS_VALID_3V detector results for.." newline bitfld.long 0x0 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0x0 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0x0 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0x0 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0x0 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0: Use the results of the internal VBUS_VALID and..,1: Use the override values for VBUS_VALID AVALID.." newline bitfld.long 0x0 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0: 4.0 V,1: 4.1 V,2: 4.2 V,3: 4.3 V,4: 4.4 V (Default),5: 4.5 V,6: 4.6 V,7: 4.7 V" line.long 0x4 "USB1_VBUS_DETECT_SET,USB PHY VBUS Detect Control Register" bitfld.long 0x4 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline bitfld.long 0x4 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline bitfld.long 0x4 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline bitfld.long 0x4 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0x4 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0x4 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline bitfld.long 0x4 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline bitfld.long 0x4 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0x4 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0x4 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0x4 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0x4 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline bitfld.long 0x4 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" line.long 0x8 "USB1_VBUS_DETECT_CLR,USB PHY VBUS Detect Control Register" eventfld.long 0x8 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline eventfld.long 0x8 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline eventfld.long 0x8 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline eventfld.long 0x8 12. "ID_OVERRIDE,TBA" "0,1" newline eventfld.long 0x8 11. "ID_OVERRIDE_EN,TBA" "0,1" newline eventfld.long 0x8 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline eventfld.long 0x8 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline eventfld.long 0x8 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline eventfld.long 0x8 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline eventfld.long 0x8 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline eventfld.long 0x8 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline eventfld.long 0x8 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline eventfld.long 0x8 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" line.long 0xC "USB1_VBUS_DETECT_TOG,USB PHY VBUS Detect Control Register" bitfld.long 0xC 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline bitfld.long 0xC 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline bitfld.long 0xC 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline bitfld.long 0xC 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0xC 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0xC 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline bitfld.long 0xC 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline bitfld.long 0xC 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0xC 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0xC 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0xC 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0xC 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline bitfld.long 0xC 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" rgroup.long 0xD0++0x3 line.long 0x0 "USB1_VBUS_DET_STAT,USB PHY VBUS Detector Status Register" bitfld.long 0x0 4. "VBUS_VALID_3V,VBUS_VALID_3V detector status" "0: VBUS voltage is below VBUS_VALID_3V threshold,1: VBUS voltage is above VBUS_VALID_3V threshold" newline bitfld.long 0x0 3. "VBUS_VALID,VBUS voltage status" "0: VBUS is below the comparator threshold,1: VBUS is above the comparator threshold" newline bitfld.long 0x0 2. "AVALID,A-Device Session Valid status" "0: The VBUS voltage is below the Session Valid..,1: The VBUS voltage is above the Session Valid.." newline bitfld.long 0x0 1. "BVALID,B-Device Session Valid status" "0: The VBUS voltage is below the Session Valid..,1: The VBUS voltage is above the Session Valid.." newline bitfld.long 0x0 0. "SESSEND,Session End indicator" "0: The VBUS voltage is above the Session Valid..,1: The VBUS voltage is below the Session Valid.." group.long 0xE0++0xF line.long 0x0 "USB1_CHRG_DETECT,USB PHY Charger Detect Control Register" bitfld.long 0x0 23. "BGR_BIAS,BGR_BIAS" "0: Use local bias powered from USB1_VBUS for 10uA..,1: Use bandgap bias powered from VREGIN0/VREGIN1.." newline bitfld.long 0x0 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0x4 "USB1_CHRG_DETECT_SET,USB PHY Charger Detect Control Register" bitfld.long 0x4 23. "BGR_BIAS,BGR_BIAS" "0,1" newline bitfld.long 0x4 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0x8 "USB1_CHRG_DETECT_CLR,USB PHY Charger Detect Control Register" eventfld.long 0x8 23. "BGR_BIAS,BGR_BIAS" "0,1" newline eventfld.long 0x8 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0xC "USB1_CHRG_DETECT_TOG,USB PHY Charger Detect Control Register" bitfld.long 0xC 23. "BGR_BIAS,BGR_BIAS" "0,1" newline bitfld.long 0xC 2. "PULLUP_DP,PULLUP_DP" "0,1" rgroup.long 0xF0++0x3 line.long 0x0 "USB1_CHRG_DET_STAT,USB PHY Charger Detect Status Register" bitfld.long 0x0 4. "SECDET_DCP,Battery Charging Secondary Detection phase output" "0: Charging Downstream Port (CDP) has been detected,1: Downstream Charging Port (DCP) has been detected" newline bitfld.long 0x0 3. "DP_STATE,DP_STATE" "0: DP pin voltage is < 0.8V,1: DP pin voltage is > 2.0V" newline bitfld.long 0x0 2. "DN_STATE,DN_STATE" "0: DN pin voltage is < 0.8V,1: DN pin voltage is > 2.0V" newline bitfld.long 0x0 1. "CHRG_DETECTED,Battery Charging Primary Detection phase output" "0: Standard Downstream Port (SDP) has been detected,1: Charging Port has been detected" newline bitfld.long 0x0 0. "PLUG_CONTACT,Battery Charging Data Contact Detection phase output" "0: No USB cable attachment has been detected,1: A USB cable attachment between the device and.." group.long 0x100++0x3F line.long 0x0 "ANACTRL,USB PHY Analog Control Register" bitfld.long 0x0 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0: The 15kohm nominal pulldowns on the DP and DN..,1: The 15kohm nominal pulldowns on the DP and DN.." line.long 0x4 "ANACTRL_SET,USB PHY Analog Control Register" bitfld.long 0x4 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0x8 "ANACTRL_CLR,USB PHY Analog Control Register" eventfld.long 0x8 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0xC "ANACTRL_TOG,USB PHY Analog Control Register" bitfld.long 0xC 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0x10 "USB1_LOOPBACK,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x10 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x10 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x10 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x10 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x10 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x10 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x10 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x10 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x10 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x10 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x10 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x14 "USB1_LOOPBACK_SET,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x14 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x14 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x14 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x14 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x14 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x14 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x14 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x14 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x14 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x14 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x14 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x18 "USB1_LOOPBACK_CLR,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x18 16.--23. 1. "TSTPKT,TSTPKT" newline eventfld.long 0x18 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline eventfld.long 0x18 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline eventfld.long 0x18 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline eventfld.long 0x18 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline eventfld.long 0x18 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline eventfld.long 0x18 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline eventfld.long 0x18 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline eventfld.long 0x18 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline eventfld.long 0x18 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline eventfld.long 0x18 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x1C "USB1_LOOPBACK_TOG,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x1C 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x1C 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x1C 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x1C 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x1C 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x1C 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x1C 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x1C 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x1C 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x1C 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x1C 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x20 "USB1_LOOPBACK_HSFSCNT,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x20 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x20 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x24 "USB1_LOOPBACK_HSFSCNT_SET,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x24 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x24 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x28 "USB1_LOOPBACK_HSFSCNT_CLR,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x28 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x28 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x2C "USB1_LOOPBACK_HSFSCNT_TOG,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x2C 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x2C 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x30 "TRIM_OVERRIDE_EN,USB PHY Trim Override Enable Register" hexmask.long.byte 0x30 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x30 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x30 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x30 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x30 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x30 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x30 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x30 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x30 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x30 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x30 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x30 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x30 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x30 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x34 "TRIM_OVERRIDE_EN_SET,USB PHY Trim Override Enable Register" hexmask.long.byte 0x34 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x34 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x34 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x34 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x34 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x34 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x34 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x34 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x34 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x34 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x34 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x34 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x34 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x34 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x38 "TRIM_OVERRIDE_EN_CLR,USB PHY Trim Override Enable Register" hexmask.long.byte 0x38 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x38 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x38 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline eventfld.long 0x38 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline eventfld.long 0x38 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline eventfld.long 0x38 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline eventfld.long 0x38 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline eventfld.long 0x38 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline eventfld.long 0x38 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline eventfld.long 0x38 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline eventfld.long 0x38 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline eventfld.long 0x38 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline eventfld.long 0x38 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline eventfld.long 0x38 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x3C "TRIM_OVERRIDE_EN_TOG,USB PHY Trim Override Enable Register" hexmask.long.byte 0x3C 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x3C 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x3C 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x3C 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x3C 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x3C 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x3C 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x3C 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x3C 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x3C 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x3C 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x3C 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x3C 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x3C 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" tree.end tree "USBPHY2" base ad:0x40438000 group.long 0x0++0x43 line.long 0x0 "PWD,USB PHY Power-Down Register" bitfld.long 0x0 20. "RXPWDRX,RXPWDRX" "0: Normal operation,1: Power-down the entire USB PHY receiver block.." newline bitfld.long 0x0 19. "RXPWDDIFF,RXPWDDIFF" "0: Normal operation.,1: Power-down the USB high-speed differential.." newline bitfld.long 0x0 18. "RXPWD1PT1,RXPWD1PT1" "0: Normal operation,1: Power-down the USB full-speed differential.." newline bitfld.long 0x0 17. "RXPWDENV,RXPWDENV" "0: Normal operation.,1: Power-down the USB high-speed receiver envelope.." newline bitfld.long 0x0 12. "TXPWDV2I,TXPWDV2I" "0: Normal operation.,1: Power-down the USB PHY transmit V-to-I converter.." newline bitfld.long 0x0 11. "TXPWDIBIAS,TXPWDIBIAS" "0: Normal operation,1: Power-down the USB PHY current bias block for.." newline bitfld.long 0x0 10. "TXPWDFS,TXPWDFS" "0: Normal operation.,1: Power-down the USB full-speed drivers. This.." line.long 0x4 "PWD_SET,USB PHY Power-Down Register" bitfld.long 0x4 20. "RXPWDRX,RXPWDRX" "0,1" newline bitfld.long 0x4 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline bitfld.long 0x4 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline bitfld.long 0x4 17. "RXPWDENV,RXPWDENV" "0,1" newline bitfld.long 0x4 12. "TXPWDV2I,TXPWDV2I" "0,1" newline bitfld.long 0x4 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline bitfld.long 0x4 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0x8 "PWD_CLR,USB PHY Power-Down Register" eventfld.long 0x8 20. "RXPWDRX,RXPWDRX" "0,1" newline eventfld.long 0x8 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline eventfld.long 0x8 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline eventfld.long 0x8 17. "RXPWDENV,RXPWDENV" "0,1" newline eventfld.long 0x8 12. "TXPWDV2I,TXPWDV2I" "0,1" newline eventfld.long 0x8 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline eventfld.long 0x8 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0xC "PWD_TOG,USB PHY Power-Down Register" bitfld.long 0xC 20. "RXPWDRX,RXPWDRX" "0,1" newline bitfld.long 0xC 19. "RXPWDDIFF,RXPWDDIFF" "0,1" newline bitfld.long 0xC 18. "RXPWD1PT1,RXPWD1PT1" "0,1" newline bitfld.long 0xC 17. "RXPWDENV,RXPWDENV" "0,1" newline bitfld.long 0xC 12. "TXPWDV2I,TXPWDV2I" "0,1" newline bitfld.long 0xC 11. "TXPWDIBIAS,TXPWDIBIAS" "0,1" newline bitfld.long 0xC 10. "TXPWDFS,TXPWDFS" "0,1" line.long 0x10 "TX,USB PHY Transmitter Control Register" hexmask.long.byte 0x10 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x10 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x10 0.--3. 1. "D_CAL,D_CAL" line.long 0x14 "TX_SET,USB PHY Transmitter Control Register" hexmask.long.byte 0x14 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x14 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x14 0.--3. 1. "D_CAL,D_CAL" line.long 0x18 "TX_CLR,USB PHY Transmitter Control Register" hexmask.long.byte 0x18 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x18 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x18 0.--3. 1. "D_CAL,D_CAL" line.long 0x1C "TX_TOG,USB PHY Transmitter Control Register" hexmask.long.byte 0x1C 16.--19. 1. "TXCAL45DP,TXCAL45DP" newline hexmask.long.byte 0x1C 8.--11. 1. "TXCAL45DN,TXCAL45DN" newline hexmask.long.byte 0x1C 0.--3. 1. "D_CAL,D_CAL" line.long 0x20 "RX,USB PHY Receiver Control Register" bitfld.long 0x20 22. "RXDBYPASS,RXDBYPASS" "0: Normal operation.,1: Use the output of the USB_DP single-ended.." newline bitfld.long 0x20 4.--6. "DISCONADJ,DISCONADJ" "0: Trip-Level Voltage is 0.56875 V,1: Trip-Level Voltage is 0.55000 V,2: Trip-Level Voltage is 0.58125 V,3: Trip-Level Voltage is 0.60000 V,?,?,?,?" newline bitfld.long 0x20 0.--2. "ENVADJ,ENVADJ" "0: Trip-Level Voltage is 0.1000 V,1: Trip-Level Voltage is 0.1125 V,2: Trip-Level Voltage is 0.1250 V,3: Trip-Level Voltage is 0.0875 V,?,?,?,?" line.long 0x24 "RX_SET,USB PHY Receiver Control Register" bitfld.long 0x24 22. "RXDBYPASS,RXDBYPASS" "0,1" newline bitfld.long 0x24 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x24 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x28 "RX_CLR,USB PHY Receiver Control Register" eventfld.long 0x28 22. "RXDBYPASS,RXDBYPASS" "0,1" newline eventfld.long 0x28 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline eventfld.long 0x28 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x2C "RX_TOG,USB PHY Receiver Control Register" bitfld.long 0x2C 22. "RXDBYPASS,RXDBYPASS" "0,1" newline bitfld.long 0x2C 4.--6. "DISCONADJ,DISCONADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x2C 0.--2. "ENVADJ,ENVADJ" "0,1,2,3,4,5,6,7" line.long 0x30 "CTRL,USB PHY General Control Register" bitfld.long 0x30 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x30 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x30 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x30 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x30 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x30 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x30 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x30 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x30 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x30 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x30 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x30 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x30 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x30 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x30 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x30 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x30 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x30 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x30 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x30 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x30 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x30 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x30 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x30 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x30 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0: Disables 200kohm pullup resistors on DP and DN..,1: Enables 200kohm pullup resistors on DP and DN pins" newline bitfld.long 0x30 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x30 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x30 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x30 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x34 "CTRL_SET,USB PHY General Control Register" bitfld.long 0x34 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x34 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x34 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x34 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x34 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x34 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x34 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x34 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x34 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x34 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x34 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x34 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x34 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x34 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x34 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x34 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x34 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x34 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x34 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x34 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x34 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x34 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x34 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x34 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x34 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline bitfld.long 0x34 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x34 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x34 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x34 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x38 "CTRL_CLR,USB PHY General Control Register" eventfld.long 0x38 31. "SFTRST,SFTRST" "0,1" newline eventfld.long 0x38 30. "CLKGATE,CLKGATE" "0,1" newline eventfld.long 0x38 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline eventfld.long 0x38 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline eventfld.long 0x38 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline eventfld.long 0x38 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline eventfld.long 0x38 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline eventfld.long 0x38 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline eventfld.long 0x38 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline eventfld.long 0x38 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline eventfld.long 0x38 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline eventfld.long 0x38 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline eventfld.long 0x38 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline eventfld.long 0x38 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline eventfld.long 0x38 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline eventfld.long 0x38 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline eventfld.long 0x38 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline eventfld.long 0x38 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline eventfld.long 0x38 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline eventfld.long 0x38 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline eventfld.long 0x38 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline eventfld.long 0x38 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline eventfld.long 0x38 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline eventfld.long 0x38 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline eventfld.long 0x38 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline eventfld.long 0x38 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline eventfld.long 0x38 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline eventfld.long 0x38 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline eventfld.long 0x38 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x3C "CTRL_TOG,USB PHY General Control Register" bitfld.long 0x3C 31. "SFTRST,SFTRST" "0,1" newline bitfld.long 0x3C 30. "CLKGATE,CLKGATE" "0,1" newline rbitfld.long 0x3C 29. "UTMI_SUSPENDM,UTMI_SUSPENDM" "0,1" newline bitfld.long 0x3C 28. "HOST_FORCE_LS_SE0,HOST_FORCE_LS_SE0" "0,1" newline rbitfld.long 0x3C 27. "OTG_ID_VALUE,OTG_ID_VALUE" "0,1" newline bitfld.long 0x3C 24. "FSDLL_RST_EN,FSDLL_RST_EN" "0,1" newline bitfld.long 0x3C 23. "ENVBUSCHG_WKUP,ENVBUSCHG_WKUP" "0,1" newline bitfld.long 0x3C 22. "ENIDCHG_WKUP,ENIDCHG_WKUP" "0,1" newline bitfld.long 0x3C 21. "ENDPDMCHG_WKUP,ENDPDMCHG_WKUP" "0,1" newline bitfld.long 0x3C 20. "ENAUTOCLR_PHY_PWD,ENAUTOCLR_PHY_PWD" "0,1" newline bitfld.long 0x3C 19. "ENAUTOCLR_CLKGATE,ENAUTOCLR_CLKGATE" "0,1" newline bitfld.long 0x3C 18. "AUTORESUME_EN,AUTORESUME_EN" "0,1" newline bitfld.long 0x3C 17. "WAKEUP_IRQ,WAKEUP_IRQ" "0,1" newline bitfld.long 0x3C 16. "ENIRQWAKEUP,ENIRQWAKEUP" "0,1" newline bitfld.long 0x3C 15. "ENUTMILEVEL3,ENUTMILEVEL3" "0,1" newline bitfld.long 0x3C 14. "ENUTMILEVEL2,ENUTMILEVEL2" "0,1" newline bitfld.long 0x3C 12. "DEVPLUGIN_IRQ,DEVPLUGIN_IRQ" "0,1" newline bitfld.long 0x3C 11. "ENIRQDEVPLUGIN,ENIRQDEVPLUGIN" "0,1" newline bitfld.long 0x3C 10. "RESUME_IRQ,RESUME_IRQ" "0,1" newline bitfld.long 0x3C 9. "ENIRQRESUMEDETECT,ENIRQRESUMEDETECT" "0,1" newline bitfld.long 0x3C 8. "RESUMEIRQSTICKY,RESUMEIRQSTICKY" "0,1" newline bitfld.long 0x3C 7. "ENOTGIDDETECT,ENOTGIDDETECT" "0,1" newline bitfld.long 0x3C 6. "OTG_ID_CHG_IRQ,OTG_ID_CHG_IRQ" "0,1" newline bitfld.long 0x3C 5. "DEVPLUGIN_POLARITY,DEVPLUGIN_POLARITY" "0,1" newline bitfld.long 0x3C 4. "ENDEVPLUGINDETECT,Enables non-standard resistive plugged-in detection" "0,1" newline bitfld.long 0x3C 3. "HOSTDISCONDETECT_IRQ,HOSTDISCONDETECT_IRQ" "0,1" newline bitfld.long 0x3C 2. "ENIRQHOSTDISCON,ENIRQHOSTDISCON" "0,1" newline bitfld.long 0x3C 1. "ENHOSTDISCONDETECT,ENHOSTDISCONDETECT" "0,1" newline bitfld.long 0x3C 0. "ENOTG_ID_CHG_IRQ,ENOTG_ID_CHG_IRQ" "0,1" line.long 0x40 "STATUS,USB PHY Status Register" rbitfld.long 0x40 10. "RESUME_STATUS,RESUME_STATUS" "0,1" newline bitfld.long 0x40 8. "OTGID_STATUS,OTGID_STATUS" "0,1" newline rbitfld.long 0x40 6. "DEVPLUGIN_STATUS,Status indicator for non-standard resistive plugged-in detection" "0: No attachment to a USB host is detected,1: Cable attachment to a USB host is detected" newline rbitfld.long 0x40 3. "HOSTDISCONDETECT_STATUS,HOSTDISCONDETECT_STATUS" "0: USB cable disconnect has not been detected at..,1: USB cable disconnect has been detected at the.." group.long 0x50++0xF line.long 0x0 "DEBUG,USB PHY Debug Register" bitfld.long 0x0 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0x0 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x0 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0x0 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x0 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0x0 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x0 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0x0 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x0 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x0 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0x0 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0x4 "DEBUG_SET,USB PHY Debug Register" bitfld.long 0x4 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0x4 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x4 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0x4 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x4 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0x4 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x4 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0x4 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x4 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0x4 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0x4 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0x8 "DEBUG_CLR,USB PHY Debug Register" eventfld.long 0x8 30. "CLKGATE,CLKGATE" "0,1" newline eventfld.long 0x8 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0x8 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline eventfld.long 0x8 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0x8 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline eventfld.long 0x8 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0x8 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline eventfld.long 0x8 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline eventfld.long 0x8 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline eventfld.long 0x8 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline eventfld.long 0x8 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" line.long 0xC "DEBUG_TOG,USB PHY Debug Register" bitfld.long 0xC 30. "CLKGATE,CLKGATE" "0,1" newline bitfld.long 0xC 29. "HOST_RESUME_DEBUG,HOST_RESUME_DEBUG" "0,1" newline hexmask.long.byte 0xC 25.--28. 1. "SQUELCHRESETLENGTH,SQUELCHRESETLENGTH" newline bitfld.long 0xC 24. "ENSQUELCHRESET,ENSQUELCHRESET" "0,1" newline hexmask.long.byte 0xC 16.--20. 1. "SQUELCHRESETCOUNT,SQUELCHRESETCOUNT" newline bitfld.long 0xC 12. "ENTX2RXCOUNT,ENTX2RXCOUNT" "0,1" newline hexmask.long.byte 0xC 8.--11. 1. "TX2RXCOUNT,TX2RXCOUNT" newline bitfld.long 0xC 4.--5. "ENHSTPULLDOWN,ENHSTPULLDOWN" "0,1,2,3" newline bitfld.long 0xC 2.--3. "HSTPULLDOWN,HSTPULLDOWN" "0,1,2,3" newline bitfld.long 0xC 1. "DEBUG_INTERFACE_HOLD,DEBUG_INTERFACE_HOLD" "0,1" newline bitfld.long 0xC 0. "OTGIDPIOLOCK,OTGIDPIOLOCK" "0,1" rgroup.long 0x60++0x3 line.long 0x0 "DEBUG0_STATUS,UTMI Debug Status Register 0" hexmask.long.byte 0x0 26.--31. 1. "SQUELCH_COUNT,SQUELCH_COUNT" newline hexmask.long.word 0x0 16.--25. 1. "UTMI_RXERROR_FAIL_COUNT,UTMI_RXERROR_FAIL_COUNT" newline hexmask.long.word 0x0 0.--15. 1. "LOOP_BACK_FAIL_COUNT,LOOP_BACK_FAIL_COUNT" group.long 0x70++0xF line.long 0x0 "DEBUG1,UTMI Debug Status Register 1" bitfld.long 0x0 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0x0 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0x0 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0x0 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0x0 13.--14. "ENTAILADJVD,ENTAILADJVD" "0: Delay is nominal,1: Delay is +20%,2: Delay is -20%,3: Delay is -40%" line.long 0x4 "DEBUG1_SET,UTMI Debug Status Register 1" bitfld.long 0x4 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0x4 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0x4 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0x4 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0x4 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" line.long 0x8 "DEBUG1_CLR,UTMI Debug Status Register 1" eventfld.long 0x8 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline eventfld.long 0x8 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline eventfld.long 0x8 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline eventfld.long 0x8 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline eventfld.long 0x8 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" line.long 0xC "DEBUG1_TOG,UTMI Debug Status Register 1" bitfld.long 0xC 21.--22. "USB2_REFBIAS_TST,Bias current control for usb2_phy" "0,1,2,3" newline bitfld.long 0xC 18.--20. "USB2_REFBIAS_VBGADJ,Adjustment bits on bandgap" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 17. "USB2_REFBIAS_LOWPWR,to be added" "0,1" newline bitfld.long 0xC 16. "USB2_REFBIAS_PWDVBGUP,Powers down the bandgap detect logic will affect vbgup on misc1 register." "0,1" newline bitfld.long 0xC 15. "USB2_REFBIAS_SELFBIASOFF,Set to 1 to disable self bias 100 us after power up refbias(usb2_refbias_pwd).This can reduce noise on power." "0,1" newline bitfld.long 0xC 13.--14. "ENTAILADJVD,ENTAILADJVD" "0,1,2,3" rgroup.long 0x80++0x3 line.long 0x0 "VERSION,UTMI RTL Version" hexmask.long.byte 0x0 24.--31. 1. "MAJOR,MAJOR" newline hexmask.long.byte 0x0 16.--23. 1. "MINOR,MINOR" newline hexmask.long.word 0x0 0.--15. 1. "STEP,STEP" group.long 0xA0++0xF line.long 0x0 "PLL_SIC,USB PHY PLL Control/Status Register" rbitfld.long 0x0 31. "PLL_LOCK,PLL_LOCK" "0: PLL is not currently locked,1: PLL is currently locked" newline bitfld.long 0x0 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0: Divide by 13,1: Divide by 15,2: Divide by 16,3: Divide by 20,4: Divide by 22,5: Divide by 25,6: Divide by 30,7: Divide by 240" newline bitfld.long 0x0 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0x0 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0x0 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0: Selects PLL_POWER to control the reference bias,1: Selects REFBIAS_PWD to control the reference bias." newline bitfld.long 0x0 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0x0 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0x0 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0x0 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0x0 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0x4 "PLL_SIC_SET,USB PHY PLL Control/Status Register" rbitfld.long 0x4 31. "PLL_LOCK,PLL_LOCK" "0,1" newline bitfld.long 0x4 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0x4 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0x4 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline bitfld.long 0x4 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0x4 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0x4 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0x4 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0x4 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0x8 "PLL_SIC_CLR,USB PHY PLL Control/Status Register" eventfld.long 0x8 31. "PLL_LOCK,PLL_LOCK" "0,1" newline eventfld.long 0x8 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline eventfld.long 0x8 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline eventfld.long 0x8 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline eventfld.long 0x8 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline eventfld.long 0x8 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline eventfld.long 0x8 12. "PLL_POWER,PLL_POWER" "0,1" newline eventfld.long 0x8 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline eventfld.long 0x8 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" line.long 0xC "PLL_SIC_TOG,USB PHY PLL Control/Status Register" rbitfld.long 0xC 31. "PLL_LOCK,PLL_LOCK" "0,1" newline bitfld.long 0xC 22.--24. "PLL_DIV_SEL,PLL_DIV_SEL" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 21. "PLL_REG_ENABLE,PLL_REG_ENABLE" "0,1" newline bitfld.long 0xC 20. "REFBIAS_PWD,Power down the reference bias" "0,1" newline bitfld.long 0xC 19. "REFBIAS_PWD_SEL,REFBIAS_PWD_SEL" "0,1" newline bitfld.long 0xC 16. "PLL_BYPASS,PLL_BYPASS" "0,1" newline bitfld.long 0xC 13. "PLL_ENABLE,PLL_ENABLE" "0,1" newline bitfld.long 0xC 12. "PLL_POWER,PLL_POWER" "0,1" newline bitfld.long 0xC 6. "PLL_EN_USB_CLKS,PLL_EN_USB_CLKS" "0,1" newline bitfld.long 0xC 2.--4. "PLL_POSTDIV,PLL_POSTDIV" "0,1,2,3,4,5,6,7" group.long 0xC0++0xF line.long 0x0 "USB1_VBUS_DETECT,USB PHY VBUS Detect Control Register" bitfld.long 0x0 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0: Disable resistive charger detection resistors on..,1: Enable resistive charger detection resistors on.." newline bitfld.long 0x0 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0: VBUS discharge resistor is disabled (Default),1: VBUS discharge resistor is enabled" newline bitfld.long 0x0 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0: Powers down the VBUS_VALID comparator,1: Enables the SESS_VALID comparator (default),2: Enables the 3Vdetect (default),?,?,?,?,?" newline bitfld.long 0x0 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0: Use the VBUS_VALID comparator for VBUS_VALID..,1: Use the Session End comparator for VBUS_VALID.." newline bitfld.long 0x0 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0x0 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0x0 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0: Use the VBUS_VALID comparator results for signal..,1: Use the Session Valid comparator results for..,2: Use the Session Valid comparator results for..,?" newline bitfld.long 0x0 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0: Use the VBUS_VALID comparator results for signal..,1: Use the VBUS_VALID_3V detector results for.." newline bitfld.long 0x0 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0x0 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0x0 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0x0 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0x0 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0: Use the results of the internal VBUS_VALID and..,1: Use the override values for VBUS_VALID AVALID.." newline bitfld.long 0x0 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0: 4.0 V,1: 4.1 V,2: 4.2 V,3: 4.3 V,4: 4.4 V (Default),5: 4.5 V,6: 4.6 V,7: 4.7 V" line.long 0x4 "USB1_VBUS_DETECT_SET,USB PHY VBUS Detect Control Register" bitfld.long 0x4 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline bitfld.long 0x4 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline bitfld.long 0x4 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline bitfld.long 0x4 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0x4 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0x4 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline bitfld.long 0x4 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline bitfld.long 0x4 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0x4 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0x4 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0x4 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0x4 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline bitfld.long 0x4 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" line.long 0x8 "USB1_VBUS_DETECT_CLR,USB PHY VBUS Detect Control Register" eventfld.long 0x8 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline eventfld.long 0x8 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline eventfld.long 0x8 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline eventfld.long 0x8 12. "ID_OVERRIDE,TBA" "0,1" newline eventfld.long 0x8 11. "ID_OVERRIDE_EN,TBA" "0,1" newline eventfld.long 0x8 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline eventfld.long 0x8 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline eventfld.long 0x8 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline eventfld.long 0x8 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline eventfld.long 0x8 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline eventfld.long 0x8 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline eventfld.long 0x8 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline eventfld.long 0x8 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" line.long 0xC "USB1_VBUS_DETECT_TOG,USB PHY VBUS Detect Control Register" bitfld.long 0xC 31. "EN_CHARGER_RESISTOR,Enables resistors used for an older method of resistive battery charger detection" "0,1" newline bitfld.long 0xC 26. "DISCHARGE_VBUS,Controls VBUS discharge resistor" "0,1" newline bitfld.long 0xC 20.--22. "PWRUP_CMPS,Enables the VBUS_VALID comparator" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 18. "VBUSVALID_TO_SESSVALID,Selects the comparator used for VBUS_VALID" "0,1" newline bitfld.long 0xC 12. "ID_OVERRIDE,TBA" "0,1" newline bitfld.long 0xC 11. "ID_OVERRIDE_EN,TBA" "0,1" newline bitfld.long 0xC 9.--10. "VBUS_SOURCE_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1,2,3" newline bitfld.long 0xC 8. "VBUSVALID_SEL,Selects the source of the VBUS_VALID signal reported to the USB controller" "0,1" newline bitfld.long 0xC 7. "VBUSVALID_OVERRIDE,Override value for VBUS_VALID signal sent to USB controller" "0,1" newline bitfld.long 0xC 6. "AVALID_OVERRIDE,Override value for A-Device Session Valid" "0,1" newline bitfld.long 0xC 5. "BVALID_OVERRIDE,Override value for B-Device Session Valid" "0,1" newline bitfld.long 0xC 4. "SESSEND_OVERRIDE,Override value for SESSEND" "0,1" newline bitfld.long 0xC 3. "VBUS_OVERRIDE_EN,VBUS detect signal override enable" "0,1" newline bitfld.long 0xC 0.--2. "VBUSVALID_THRESH,VBUSVALID_THRESH" "0,1,2,3,4,5,6,7" rgroup.long 0xD0++0x3 line.long 0x0 "USB1_VBUS_DET_STAT,USB PHY VBUS Detector Status Register" bitfld.long 0x0 4. "VBUS_VALID_3V,VBUS_VALID_3V detector status" "0: VBUS voltage is below VBUS_VALID_3V threshold,1: VBUS voltage is above VBUS_VALID_3V threshold" newline bitfld.long 0x0 3. "VBUS_VALID,VBUS voltage status" "0: VBUS is below the comparator threshold,1: VBUS is above the comparator threshold" newline bitfld.long 0x0 2. "AVALID,A-Device Session Valid status" "0: The VBUS voltage is below the Session Valid..,1: The VBUS voltage is above the Session Valid.." newline bitfld.long 0x0 1. "BVALID,B-Device Session Valid status" "0: The VBUS voltage is below the Session Valid..,1: The VBUS voltage is above the Session Valid.." newline bitfld.long 0x0 0. "SESSEND,Session End indicator" "0: The VBUS voltage is above the Session Valid..,1: The VBUS voltage is below the Session Valid.." group.long 0xE0++0xF line.long 0x0 "USB1_CHRG_DETECT,USB PHY Charger Detect Control Register" bitfld.long 0x0 23. "BGR_BIAS,BGR_BIAS" "0: Use local bias powered from USB1_VBUS for 10uA..,1: Use bandgap bias powered from VREGIN0/VREGIN1.." newline bitfld.long 0x0 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0x4 "USB1_CHRG_DETECT_SET,USB PHY Charger Detect Control Register" bitfld.long 0x4 23. "BGR_BIAS,BGR_BIAS" "0,1" newline bitfld.long 0x4 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0x8 "USB1_CHRG_DETECT_CLR,USB PHY Charger Detect Control Register" eventfld.long 0x8 23. "BGR_BIAS,BGR_BIAS" "0,1" newline eventfld.long 0x8 2. "PULLUP_DP,PULLUP_DP" "0,1" line.long 0xC "USB1_CHRG_DETECT_TOG,USB PHY Charger Detect Control Register" bitfld.long 0xC 23. "BGR_BIAS,BGR_BIAS" "0,1" newline bitfld.long 0xC 2. "PULLUP_DP,PULLUP_DP" "0,1" rgroup.long 0xF0++0x3 line.long 0x0 "USB1_CHRG_DET_STAT,USB PHY Charger Detect Status Register" bitfld.long 0x0 4. "SECDET_DCP,Battery Charging Secondary Detection phase output" "0: Charging Downstream Port (CDP) has been detected,1: Downstream Charging Port (DCP) has been detected" newline bitfld.long 0x0 3. "DP_STATE,DP_STATE" "0: DP pin voltage is < 0.8V,1: DP pin voltage is > 2.0V" newline bitfld.long 0x0 2. "DN_STATE,DN_STATE" "0: DN pin voltage is < 0.8V,1: DN pin voltage is > 2.0V" newline bitfld.long 0x0 1. "CHRG_DETECTED,Battery Charging Primary Detection phase output" "0: Standard Downstream Port (SDP) has been detected,1: Charging Port has been detected" newline bitfld.long 0x0 0. "PLUG_CONTACT,Battery Charging Data Contact Detection phase output" "0: No USB cable attachment has been detected,1: A USB cable attachment between the device and.." group.long 0x100++0x3F line.long 0x0 "ANACTRL,USB PHY Analog Control Register" bitfld.long 0x0 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0: The 15kohm nominal pulldowns on the DP and DN..,1: The 15kohm nominal pulldowns on the DP and DN.." line.long 0x4 "ANACTRL_SET,USB PHY Analog Control Register" bitfld.long 0x4 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0x8 "ANACTRL_CLR,USB PHY Analog Control Register" eventfld.long 0x8 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0xC "ANACTRL_TOG,USB PHY Analog Control Register" bitfld.long 0xC 10. "DEV_PULLDOWN,DEV_PULLDOWN" "0,1" line.long 0x10 "USB1_LOOPBACK,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x10 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x10 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x10 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x10 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x10 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x10 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x10 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x10 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x10 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x10 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x10 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x14 "USB1_LOOPBACK_SET,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x14 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x14 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x14 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x14 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x14 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x14 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x14 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x14 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x14 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x14 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x14 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x18 "USB1_LOOPBACK_CLR,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x18 16.--23. 1. "TSTPKT,TSTPKT" newline eventfld.long 0x18 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline eventfld.long 0x18 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline eventfld.long 0x18 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline eventfld.long 0x18 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline eventfld.long 0x18 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline eventfld.long 0x18 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline eventfld.long 0x18 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline eventfld.long 0x18 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline eventfld.long 0x18 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline eventfld.long 0x18 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x1C "USB1_LOOPBACK_TOG,USB PHY Loopback Control/Status Register" hexmask.long.byte 0x1C 16.--23. 1. "TSTPKT,TSTPKT" newline bitfld.long 0x1C 15. "TSTI_HSFS_MODE_EN,TSTI_HSFS_MODE_EN" "0,1" newline rbitfld.long 0x1C 8. "UTMO_DIG_TST1,UTMO_DIG_TST1" "0,1" newline rbitfld.long 0x1C 7. "UTMO_DIG_TST0,UTMO_DIG_TST0" "0,1" newline bitfld.long 0x1C 6. "TSTI_TX_HIZ,TSTI_TX_HIZ" "0,1" newline bitfld.long 0x1C 5. "TSTI_TX_EN,TSTI_TX_EN" "0,1" newline bitfld.long 0x1C 4. "TSTI_TX_LS_MODE,TSTI_TX_LS_MODE" "0,1" newline bitfld.long 0x1C 3. "TSTI_TX_HS_MODE,TSTI_TX_HS_MODE" "0,1" newline bitfld.long 0x1C 2. "UTMI_DIG_TST1,UTMI_DIG_TST1" "0,1" newline bitfld.long 0x1C 1. "UTMI_DIG_TST0,UTMI_DIG_TST0" "0,1" newline bitfld.long 0x1C 0. "UTMI_TESTSTART,UTMI_TESTSTART" "0,1" line.long 0x20 "USB1_LOOPBACK_HSFSCNT,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x20 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x20 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x24 "USB1_LOOPBACK_HSFSCNT_SET,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x24 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x24 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x28 "USB1_LOOPBACK_HSFSCNT_CLR,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x28 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x28 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x2C "USB1_LOOPBACK_HSFSCNT_TOG,USB PHY Loopback Packet Number Select Register" hexmask.long.word 0x2C 16.--31. 1. "TSTI_FS_NUMBER,TSTI_FS_NUMBER" newline hexmask.long.word 0x2C 0.--15. 1. "TSTI_HS_NUMBER,TSTI_HS_NUMBER" line.long 0x30 "TRIM_OVERRIDE_EN,USB PHY Trim Override Enable Register" hexmask.long.byte 0x30 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x30 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x30 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x30 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x30 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x30 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x30 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x30 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x30 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x30 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x30 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x30 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x30 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x30 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x34 "TRIM_OVERRIDE_EN_SET,USB PHY Trim Override Enable Register" hexmask.long.byte 0x34 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x34 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x34 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x34 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x34 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x34 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x34 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x34 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x34 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x34 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x34 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x34 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x34 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x34 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x38 "TRIM_OVERRIDE_EN_CLR,USB PHY Trim Override Enable Register" hexmask.long.byte 0x38 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x38 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x38 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline eventfld.long 0x38 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline eventfld.long 0x38 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline eventfld.long 0x38 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline eventfld.long 0x38 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline eventfld.long 0x38 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline eventfld.long 0x38 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline eventfld.long 0x38 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline eventfld.long 0x38 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline eventfld.long 0x38 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline eventfld.long 0x38 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline eventfld.long 0x38 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" line.long 0x3C "TRIM_OVERRIDE_EN_TOG,USB PHY Trim Override Enable Register" hexmask.long.byte 0x3C 28.--31. 1. "TRIM_USBPHY_TX_CAL45DN,TRIM_USBPHY_TX_CAL45DN" newline hexmask.long.byte 0x3C 24.--27. 1. "TRIM_USBPHY_TX_CAL45DP,TRIM_USBPHY_TX_CAL45DP" newline hexmask.long.byte 0x3C 20.--23. 1. "TRIM_USBPHY_TX_D_CAL,TRIM_USBPHY_TX_D_CAL" newline rbitfld.long 0x3C 18.--19. "TRIM_USB_REG_ENV_TAIL_ADJ_VD,TRIM_USB_REG_ENV_TAIL_ADJ_VD" "0,1,2,3" newline rbitfld.long 0x3C 15.--17. "TRIM_PLL_CTRL0_DIV_SEL,TRIM_PLL_CTRL0_DIV_SEL" "0,1,2,3,4,5,6,7" newline rbitfld.long 0x3C 13.--14. "TRIM_USB2_REFBIAS_TST,TRIM_USB2_REFBIAS_TST" "0,1,2,3" newline rbitfld.long 0x3C 10.--12. "TRIM_USB2_REFBIAS_VBGADJ,TRIM_USB2_REFBIAS_VBGADJ" "0,1,2,3,4,5,6,7" newline bitfld.long 0x3C 6. "TRIM_REFBIAS_TST_OVERRIDE,Override enable for bias current control" "0,1" newline bitfld.long 0x3C 5. "TRIM_REFBIAS_VBGADJ_OVERRIDE,Override enable for bandgap adjustment." "0,1" newline bitfld.long 0x3C 4. "TRIM_TX_CAL45DN_OVERRIDE,TRIM_TX_CAL45DN_OVERRIDE" "0,1" newline bitfld.long 0x3C 3. "TRIM_TX_CAL45DP_OVERRIDE,TRIM_TX_CAL45DP_OVERRIDE" "0,1" newline bitfld.long 0x3C 2. "TRIM_TX_D_CAL_OVERRIDE,TRIM_TX_D_CAL_OVERRIDE" "0,1" newline bitfld.long 0x3C 1. "TRIM_ENV_TAIL_ADJ_VD_OVERRIDE,TRIM_ENV_TAIL_ADJ_VD_OVERRIDE" "0,1" newline bitfld.long 0x3C 0. "TRIM_DIV_SEL_OVERRIDE,TRIM_DIV_SEL_OVERRIDE" "0,1" tree.end tree.end tree "USDHC" base ad:0x0 tree "USDHC1" base ad:0x40418000 group.long 0x0++0xF line.long 0x0 "DS_ADDR,DMA System Address" hexmask.long 0x0 0.--31. 1. "DS_ADDR,System address" line.long 0x4 "BLK_ATT,Block Attributes" hexmask.long.word 0x4 16.--31. 1. "BLKCNT,Blocks count for current transfer" newline hexmask.long.word 0x4 0.--12. 1. "BLKSIZE,Transfer block size" line.long 0x8 "CMD_ARG,Command Argument" hexmask.long 0x8 0.--31. 1. "CMDARG,Command argument" line.long 0xC "CMD_XFR_TYP,Command Transfer Type" hexmask.long.byte 0xC 24.--29. 1. "CMDINX,Command index" newline bitfld.long 0xC 22.--23. "CMDTYP,Command type" "0: Normal other commands,1: Suspend CMD52 for writing bus suspend in CCCR,2: Resume CMD52 for writing function select in CCCR,3: Abort CMD12 CMD52 for writing I/O Abort in CCCR" newline bitfld.long 0xC 21. "DPSEL,Data present select" "0: No data present,1: Data present" newline bitfld.long 0xC 20. "CICEN,Command index check enable" "0: Disable command index check,1: Enables command index check" newline bitfld.long 0xC 19. "CCCEN,Command CRC check enable" "0: Disables command CRC check,1: Enables command CRC check" newline bitfld.long 0xC 16.--17. "RSPTYP,Response type select" "0: No response,1: Response length 136,2: Response length 48,3: Response length 48 check busy after response" rgroup.long 0x10++0xF line.long 0x0 "CMD_RSP0,Command Response0" hexmask.long 0x0 0.--31. 1. "CMDRSP0,Command response 0" line.long 0x4 "CMD_RSP1,Command Response1" hexmask.long 0x4 0.--31. 1. "CMDRSP1,Command response 1" line.long 0x8 "CMD_RSP2,Command Response2" hexmask.long 0x8 0.--31. 1. "CMDRSP2,Command response 2" line.long 0xC "CMD_RSP3,Command Response3" hexmask.long 0xC 0.--31. 1. "CMDRSP3,Command response 3" group.long 0x20++0x3 line.long 0x0 "DATA_BUFF_ACC_PORT,Data Buffer Access Port" hexmask.long 0x0 0.--31. 1. "DATCONT,Data content" rgroup.long 0x24++0x3 line.long 0x0 "PRES_STATE,Present State" hexmask.long.byte 0x0 24.--31. 1. "DLSL,DATA[7:0] line signal level" newline bitfld.long 0x0 23. "CLSL,CMD line signal level" "0,1" newline bitfld.long 0x0 19. "WPSPL,Write protect switch pin level" "0: Write protected (WP = 1),1: Write enabled (WP = 0)" newline bitfld.long 0x0 18. "CDPL,Card detect pin level" "0: No card present (CD_B = 1),1: Card present (CD_B = 0)" newline bitfld.long 0x0 16. "CINST,Card inserted" "0: Power on reset or no card,1: Card inserted" newline bitfld.long 0x0 15. "TSCD,Tap select change done" "0: Delay cell select change is not finished.,1: Delay cell select change is finished." newline bitfld.long 0x0 12. "RTR,Re-Tuning Request (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Fixed or well tuned sampling clock,1: Sampling clock needs re-tuning" newline bitfld.long 0x0 11. "BREN,Buffer read enable" "0: Read disable,1: Read enable" newline bitfld.long 0x0 10. "BWEN,Buffer write enable" "0: Write disable,1: Write enable" newline bitfld.long 0x0 9. "RTA,Read transfer active" "0: No valid data,1: Transferring data" newline bitfld.long 0x0 8. "WTA,Write transfer active" "0: No valid data,1: Transferring data" newline bitfld.long 0x0 7. "SDOFF,SD clock gated off internally" "0: SD clock is active.,1: SD clock is gated off." newline bitfld.long 0x0 6. "PEROFF,IPG_PERCLK gated off internally" "0: IPG_PERCLK is active.,1: IPG_PERCLK is gated off." newline bitfld.long 0x0 5. "HCKOFF,HCLK gated off internally" "0: HCLK is active.,1: HCLK is gated off." newline bitfld.long 0x0 4. "IPGOFF,Peripheral clock gated off internally" "0: Peripheral clock is active.,1: Peripheral clock is gated off." newline bitfld.long 0x0 3. "SDSTB,SD clock stable" "0: Clock is changing frequency and not stable.,1: Clock is stable." newline bitfld.long 0x0 2. "DLA,Data line active" "0: DATA line inactive,1: DATA line active" newline bitfld.long 0x0 1. "CDIHB,Command Inhibit Data (DATA)" "0: Can issue command that uses the DATA line,1: Cannot issue command that uses the DATA line" newline bitfld.long 0x0 0. "CIHB,Command inhibit (CMD)" "0: Can issue command using only CMD line,1: Cannot issue command" group.long 0x28++0x23 line.long 0x0 "PROT_CTRL,Protocol Control" bitfld.long 0x0 30. "NON_EXACT_BLK_RD,Non-exact block read" "0: The block read is exact block read. Host driver..,1: The block read is non-exact block read. Host.." newline bitfld.long 0x0 26. "WECRM,Wakeup event enable on SD card removal" "0: Disables wakeup event enable on SD card removal,1: Enables wakeup event enable on SD card removal" newline bitfld.long 0x0 25. "WECINS,Wakeup event enable on SD card insertion" "0: Disable wakeup event enable on SD card insertion,1: Enable wakeup event enable on SD card insertion" newline bitfld.long 0x0 24. "WECINT,Wakeup event enable on card interrupt" "0: Disables wakeup event enable on card interrupt,1: Enables wakeup event enable on card interrupt" newline bitfld.long 0x0 20. "RD_DONE_NO_8CLK,Read performed number 8 clock" "0,1" newline bitfld.long 0x0 19. "IABG,Interrupt at block gap" "0: Disables interrupt at block gap,1: Enables interrupt at block gap" newline bitfld.long 0x0 18. "RWCTL,Read wait control" "0: Disables read wait control and stop SD clock at..,1: Enables read wait control and assert read wait.." newline bitfld.long 0x0 17. "CREQ,Continue request" "0: No effect,1: Restart" newline bitfld.long 0x0 16. "SABGREQ,Stop at block gap request" "0: Transfer,1: Stop" newline bitfld.long 0x0 8.--9. "DMASEL,DMA select" "0: No DMA or simple DMA is selected.,1: ADMA1 is selected.,2: ADMA2 is selected.,?" newline bitfld.long 0x0 7. "CDSS,Card detect signal selection" "0: Card detection level is selected (for normal..,1: Card detection test level is selected (for test.." newline bitfld.long 0x0 6. "CDTL,Card detect test level" "0: Card detect test level is 0 no card inserted,1: Card detect test level is 1 card inserted" newline bitfld.long 0x0 4.--5. "EMODE,Endian mode" "0: Big endian mode,1: Half word big endian mode,2: Little endian mode,?" newline bitfld.long 0x0 3. "D3CD,DATA3 as card detection pin" "0: DATA3 does not monitor card insertion,1: DATA3 as card detection pin" newline bitfld.long 0x0 1.--2. "DTW,Data transfer width" "0: 1-bit mode,1: 4-bit mode,2: 8-bit mode,?" line.long 0x4 "SYS_CTRL,System Control" bitfld.long 0x4 28. "RSTT,Reset tuning" "0,1" newline bitfld.long 0x4 27. "INITA,Initialization active" "0,1" newline bitfld.long 0x4 26. "RSTD,Software reset for data line" "0: No reset,1: Reset" newline bitfld.long 0x4 25. "RSTC,Software reset for CMD line" "0: No reset,1: Reset" newline bitfld.long 0x4 24. "RSTA,Software reset for all" "0: No reset,1: Reset" newline bitfld.long 0x4 23. "IPP_RST_N,Hardware reset" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "DTOCV,Data timeout counter value" newline hexmask.long.byte 0x4 8.--15. 1. "SDCLKFS,SDCLK frequency select" newline hexmask.long.byte 0x4 4.--7. 1. "DVS,Divisor" line.long 0x8 "INT_STATUS,Interrupt Status" eventfld.long 0x8 28. "DMAE,DMA error" "0: No error,1: Error" newline eventfld.long 0x8 26. "TNE,Tuning error: (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0,1" newline eventfld.long 0x8 24. "AC12E,Auto CMD12 error" "0: No error,1: Error" newline eventfld.long 0x8 22. "DEBE,Data end bit error" "0: No error,1: Error" newline eventfld.long 0x8 21. "DCE,Data CRC error" "0: No error,1: Error" newline eventfld.long 0x8 20. "DTOE,Data timeout error" "0: No error,1: Time out" newline eventfld.long 0x8 19. "CIE,Command index error" "0: No error,1: Error" newline eventfld.long 0x8 18. "CEBE,Command end bit error" "0: No error,1: End bit error generated" newline eventfld.long 0x8 17. "CCE,Command CRC error" "0: No error,1: CRC error generated" newline eventfld.long 0x8 16. "CTOE,Command timeout error" "0: No error,1: Time out" newline eventfld.long 0x8 14. "TP,Tuning pass:(only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0,1" newline eventfld.long 0x8 12. "RTE,Re-tuning event: (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Re-tuning is not required.,1: Re-tuning should be performed." newline eventfld.long 0x8 8. "CINT,Card interrupt" "0: No card interrupt,1: Generate card interrupt" newline eventfld.long 0x8 7. "CRM,Card removal" "0: Card state unstable or inserted,1: Card removed" newline eventfld.long 0x8 6. "CINS,Card insertion" "0: Card state unstable or removed,1: Card inserted" newline eventfld.long 0x8 5. "BRR,Buffer read ready" "0: Not ready to read buffer,1: Ready to read buffer" newline eventfld.long 0x8 4. "BWR,Buffer write ready" "0: Not ready to write buffer,1: Ready to write buffer" newline eventfld.long 0x8 3. "DINT,DMA interrupt" "0: No DMA interrupt,1: DMA interrupt is generated." newline eventfld.long 0x8 2. "BGE,Block gap event" "0: No block gap event,1: Transaction stopped at block gap" newline eventfld.long 0x8 1. "TC,Transfer complete" "0: Transfer does not complete,1: Transfer complete" newline eventfld.long 0x8 0. "CC,Command complete" "0: Command not complete,1: Command complete" line.long 0xC "INT_STATUS_EN,Interrupt Status Enable" bitfld.long 0xC 28. "DMAESEN,DMA error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 26. "TNESEN,Tuning error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 24. "AC12ESEN,Auto CMD12 error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 22. "DEBESEN,Data end bit error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 21. "DCESEN,Data CRC error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 20. "DTOESEN,Data timeout error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 19. "CIESEN,Command index error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 18. "CEBESEN,Command end bit error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 17. "CCESEN,Command CRC error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 16. "CTOESEN,Command timeout error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 14. "TPSEN,Tuning pass status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 12. "RTESEN,Re-tuning event status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 8. "CINTSEN,Card interrupt status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 7. "CRMSEN,Card removal status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 6. "CINSSEN,Card insertion status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 5. "BRRSEN,Buffer read ready status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 4. "BWRSEN,Buffer write ready status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 3. "DINTSEN,DMA interrupt status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 2. "BGESEN,Block gap event status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 1. "TCSEN,Transfer complete status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 0. "CCSEN,Command complete status enable" "0: Masked,1: Enabled" line.long 0x10 "INT_SIGNAL_EN,Interrupt Signal Enable" bitfld.long 0x10 28. "DMAEIEN,DMA error interrupt enable" "0: Masked,1: Enable" newline bitfld.long 0x10 26. "TNEIEN,Tuning error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 24. "AC12EIEN,Auto CMD12 error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 22. "DEBEIEN,Data end bit error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 21. "DCEIEN,Data CRC error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 20. "DTOEIEN,Data timeout error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 19. "CIEIEN,Command index error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 18. "CEBEIEN,Command end bit error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 17. "CCEIEN,Command CRC error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 16. "CTOEIEN,Command timeout error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 14. "TPIEN,Tuning Pass interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 12. "RTEIEN,Re-tuning event interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 8. "CINTIEN,Card interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 7. "CRMIEN,Card removal interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 6. "CINSIEN,Card insertion interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 5. "BRRIEN,Buffer read ready interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 4. "BWRIEN,Buffer write ready interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 3. "DINTIEN,DMA interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 2. "BGEIEN,Block gap event interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 1. "TCIEN,Transfer complete interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 0. "CCIEN,Command complete interrupt enable" "0: Masked,1: Enabled" line.long 0x14 "AUTOCMD12_ERR_STATUS,Auto CMD12 Error Status" bitfld.long 0x14 23. "SMP_CLK_SEL,Sample clock select" "0: Fixed clock is used to sample data,1: Tuned clock is used to sample data" newline bitfld.long 0x14 22. "EXECUTE_TUNING,Execute tuning" "0: Tuning procedure is aborted,1: Start tuning procedure" newline rbitfld.long 0x14 7. "CNIBAC12E,Command not issued by Auto CMD12 error" "0: No error,1: Not issued" newline rbitfld.long 0x14 4. "AC12IE,Auto CMD12 / 23 index error" "0: No error,1: Error the CMD index in response is not CMD12/23" newline rbitfld.long 0x14 3. "AC12CE,Auto CMD12 / 23 CRC error" "0: No CRC error,1: CRC error met in Auto CMD12/23 response" newline rbitfld.long 0x14 2. "AC12EBE,Auto CMD12 / 23 end bit error" "0: No error,1: End bit error generated" newline rbitfld.long 0x14 1. "AC12TOE,Auto CMD12 / 23 timeout error" "0: No error,1: Time out" newline rbitfld.long 0x14 0. "AC12NE,Auto CMD12 not executed" "0: Executed,1: Not executed" line.long 0x18 "HOST_CTRL_CAP,Host Controller Capabilities" rbitfld.long 0x18 26. "VS18,Voltage support 1.8 V" "0: 1.8 V not supported,1: 1.8 V supported" newline rbitfld.long 0x18 25. "VS30,Voltage support 3.0 V" "0: 3.0 V not supported,1: 3.0 V supported" newline rbitfld.long 0x18 24. "VS33,Voltage support 3.3 V" "0: 3.3 V not supported,1: 3.3 V supported" newline rbitfld.long 0x18 23. "SRS,Suspend / resume support" "0: Not supported,1: Supported" newline rbitfld.long 0x18 22. "DMAS,DMA support" "0: DMA not supported,1: DMA supported" newline rbitfld.long 0x18 21. "HSS,High speed support" "0: High speed not supported,1: High speed supported" newline rbitfld.long 0x18 20. "ADMAS,ADMA support" "0: Advanced DMA not supported,1: Advanced DMA supported" newline rbitfld.long 0x18 16.--18. "MBL,Max block length" "0: 512 bytes,1: 1024 bytes,2: 2048 bytes,3: 4096 bytes,?,?,?,?" newline bitfld.long 0x18 13. "USE_TUNING_SDR50,Use Tuning for SDR50" "0: SDR50 does not support tuning,1: SDR50 supports tuning" newline rbitfld.long 0x18 2. "DDR50_SUPPORT,DDR50 support" "0,1" newline rbitfld.long 0x18 1. "SDR104_SUPPORT,SDR104 support" "0,1" newline rbitfld.long 0x18 0. "SDR50_SUPPORT,SDR50 support" "0,1" line.long 0x1C "WTMK_LVL,Watermark Level" hexmask.long.byte 0x1C 16.--23. 1. "WR_WML,Write watermark level" newline hexmask.long.byte 0x1C 0.--7. 1. "RD_WML,Read watermark level" line.long 0x20 "MIX_CTRL,Mixer Control" bitfld.long 0x20 26. "HS400_MODE,Enable HS400 mode" "0,1" newline bitfld.long 0x20 25. "FBCLK_SEL,Feedback clock source selection (Only used for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Feedback clock comes from the loopback CLK,1: Feedback clock comes from the ipp_card_clk_out" newline bitfld.long 0x20 24. "AUTO_TUNE_EN,Auto tuning enable (Only used for SD3.0 SDR104 mode and and EMMC HS200 mode)" "0: Disable auto tuning,1: Enable auto tuning" newline bitfld.long 0x20 23. "SMP_CLK_SEL,Clock selection" "0: Fixed clock is used to sample data / cmd,1: Tuned clock is used to sample data / cmd" newline bitfld.long 0x20 22. "EXE_TUNE,Execute tuning: (Only used for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Not tuned or tuning completed,1: Execute tuning" newline bitfld.long 0x20 7. "AC23EN,Auto CMD23 enable" "0,1" newline bitfld.long 0x20 6. "NIBBLE_POS,Nibble position indication" "0,1" newline bitfld.long 0x20 5. "MSBSEL,Multi / Single block select" "0: Single block,1: Multiple blocks" newline bitfld.long 0x20 4. "DTDSEL,Data transfer direction select" "0: Write (Host to card),1: Read (Card to host)" newline bitfld.long 0x20 3. "DDR_EN,Dual data rate mode selection" "0,1" newline bitfld.long 0x20 2. "AC12EN,Auto CMD12 enable" "0: Disable,1: Enable" newline bitfld.long 0x20 1. "BCEN,Block count enable" "0: Disable,1: Enable" newline bitfld.long 0x20 0. "DMAEN,DMA enable" "0: Disable,1: Enable" group.long 0x50++0x3 line.long 0x0 "FORCE_EVENT,Force Event" bitfld.long 0x0 31. "FEVTCINT,Force event card interrupt" "0,1" newline bitfld.long 0x0 28. "FEVTDMAE,Force event DMA error" "0,1" newline bitfld.long 0x0 26. "FEVTTNE,Force tuning error" "0,1" newline bitfld.long 0x0 24. "FEVTAC12E,Force event Auto Command 12 error" "0,1" newline bitfld.long 0x0 22. "FEVTDEBE,Force event data end bit error" "0,1" newline bitfld.long 0x0 21. "FEVTDCE,Force event data CRC error" "0,1" newline bitfld.long 0x0 20. "FEVTDTOE,Force event data time out error" "0,1" newline bitfld.long 0x0 19. "FEVTCIE,Force event command index error" "0,1" newline bitfld.long 0x0 18. "FEVTCEBE,Force event command end bit error" "0,1" newline bitfld.long 0x0 17. "FEVTCCE,Force event command CRC error" "0,1" newline bitfld.long 0x0 16. "FEVTCTOE,Force event command time out error" "0,1" newline bitfld.long 0x0 7. "FEVTCNIBAC12E,Force event command not executed by Auto Command 12 error" "0,1" newline bitfld.long 0x0 4. "FEVTAC12IE,Force event Auto Command 12 index error" "0,1" newline bitfld.long 0x0 3. "FEVTAC12EBE,Force event Auto Command 12 end bit error" "0,1" newline bitfld.long 0x0 2. "FEVTAC12CE,Force event auto command 12 CRC error" "0,1" newline bitfld.long 0x0 1. "FEVTAC12TOE,Force event auto command 12 time out error" "0,1" newline bitfld.long 0x0 0. "FEVTAC12NE,Force event auto command 12 not executed" "0,1" rgroup.long 0x54++0x3 line.long 0x0 "ADMA_ERR_STATUS,ADMA Error Status" bitfld.long 0x0 3. "ADMADCE,ADMA descriptor error" "0: No error,1: Error" newline bitfld.long 0x0 2. "ADMALME,ADMA length mismatch error" "0: No error,1: Error" newline bitfld.long 0x0 0.--1. "ADMAES,ADMA error state (when ADMA error is occurred)" "0,1,2,3" group.long 0x58++0x3 line.long 0x0 "ADMA_SYS_ADDR,ADMA System Address" hexmask.long 0x0 2.--31. 1. "ADS_ADDR,ADMA system address" group.long 0x60++0x3 line.long 0x0 "DLL_CTRL,DLL (Delay Line) Control" hexmask.long.byte 0x0 28.--31. 1. "DLL_CTRL_REF_UPDATE_INT,DLL control loop update interval" newline hexmask.long.byte 0x0 20.--27. 1. "DLL_CTRL_SLV_UPDATE_INT,Slave delay line update interval" newline bitfld.long 0x0 16.--18. "DLL_CTRL_SLV_DLY_TARGET1,DLL slave delay target1" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 9.--15. 1. "DLL_CTRL_SLV_OVERRIDE_VAL,DLL slave override val" newline bitfld.long 0x0 8. "DLL_CTRL_SLV_OVERRIDE,DLL slave override" "0,1" newline bitfld.long 0x0 7. "DLL_CTRL_GATE_UPDATE,DLL gate update" "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "DLL_CTRL_SLV_DLY_TARGET0,DLL slave delay target0" newline bitfld.long 0x0 2. "DLL_CTRL_SLV_FORCE_UPD,DLL slave delay line" "0,1" newline bitfld.long 0x0 1. "DLL_CTRL_RESET,DLL reset" "0,1" newline bitfld.long 0x0 0. "DLL_CTRL_ENABLE,DLL and delay chain" "0,1" rgroup.long 0x64++0x3 line.long 0x0 "DLL_STATUS,DLL Status" hexmask.long.byte 0x0 9.--15. 1. "DLL_STS_REF_SEL,Reference delay line select taps" newline hexmask.long.byte 0x0 2.--8. 1. "DLL_STS_SLV_SEL,Slave delay line select status" newline bitfld.long 0x0 1. "DLL_STS_REF_LOCK,Reference DLL lock status" "0,1" newline bitfld.long 0x0 0. "DLL_STS_SLV_LOCK,Slave delay-line lock status" "0,1" group.long 0x68++0x3 line.long 0x0 "CLK_TUNE_CTRL_STATUS,CLK Tuning Control and Status" rbitfld.long 0x0 31. "PRE_ERR,PRE error" "0,1" newline hexmask.long.byte 0x0 24.--30. 1. "TAP_SEL_PRE,TAP_SEL_PRE" newline hexmask.long.byte 0x0 20.--23. 1. "TAP_SEL_OUT,Delay cells added on the feedback clock between CLK_PRE and CLK_OUT" newline hexmask.long.byte 0x0 16.--19. 1. "TAP_SEL_POST,Delay cells added on the feedback clock between CLK_OUT and CLK_POST" newline rbitfld.long 0x0 15. "NXT_ERR,NXT error" "0,1" newline hexmask.long.byte 0x0 8.--14. 1. "DLY_CELL_SET_PRE,delay cells on the feedback clock between the feedback clock and CLK_PRE" newline hexmask.long.byte 0x0 4.--7. 1. "DLY_CELL_SET_OUT,Delay cells on the feedback clock between CLK_PRE and CLK_OUT" newline hexmask.long.byte 0x0 0.--3. 1. "DLY_CELL_SET_POST,Delay cells on the feedback clock between CLK_OUT and CLK_POST" group.long 0x70++0x3 line.long 0x0 "STROBE_DLL_CTRL,Strobe DLL control" hexmask.long.byte 0x0 28.--31. 1. "STROBE_DLL_CTRL_REF_UPDATE_INT,Strobe DLL control reference update interval" newline hexmask.long.byte 0x0 20.--27. 1. "STROBE_DLL_CTRL_SLV_UPDATE_INT,Strobe DLL control slave update interval" newline hexmask.long.byte 0x0 9.--15. 1. "STROBE_DLL_CTRL_SLV_OVERRIDE_VAL,Strobe DLL control slave Override value" newline bitfld.long 0x0 8. "STROBE_DLL_CTRL_SLV_OVERRIDE,Strobe DLL control slave override" "0,1" newline bitfld.long 0x0 7. "STROBE_DLL_CTRL_GATE_UPDATE,Strobe DLL control gate update" "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "STROBE_DLL_CTRL_SLV_DLY_TARGET,Strobe DLL Control Slave Delay Target" newline bitfld.long 0x0 2. "STROBE_DLL_CTRL_SLV_FORCE_UPD,Strobe DLL control slave force updated" "0,1" newline bitfld.long 0x0 1. "STROBE_DLL_CTRL_RESET,Strobe DLL control reset" "0,1" newline bitfld.long 0x0 0. "STROBE_DLL_CTRL_ENABLE,Strobe DLL control enable" "0,1" rgroup.long 0x74++0x3 line.long 0x0 "STROBE_DLL_STATUS,Strobe DLL status" hexmask.long.byte 0x0 9.--15. 1. "STROBE_DLL_STS_REF_SEL,Strobe DLL status reference select" newline hexmask.long.byte 0x0 2.--8. 1. "STROBE_DLL_STS_SLV_SEL,Strobe DLL status slave select" newline bitfld.long 0x0 1. "STROBE_DLL_STS_REF_LOCK,Strobe DLL status reference lock" "0,1" newline bitfld.long 0x0 0. "STROBE_DLL_STS_SLV_LOCK,Strobe DLL status slave lock" "0,1" group.long 0xC0++0xF line.long 0x0 "VEND_SPEC,Vendor Specific Register" bitfld.long 0x0 31. "CMD_BYTE_EN,Byte access" "0: Disable,1: Enable" newline bitfld.long 0x0 15. "CRC_CHK_DIS,CRC Check Disable" "0: Check CRC16 for every read data packet and check..,1: Ignore CRC16 check for every read data packet.." newline bitfld.long 0x0 8. "FRC_SDCLK_ON,Force CLK" "0: CLK active or inactive is fully controlled by..,1: Force CLK active" newline bitfld.long 0x0 3. "AC12_WR_CHKBUSY_EN,Check busy enable" "0: Do not check busy after auto CMD12 for write..,1: Check busy after auto CMD12 for write data packet" newline bitfld.long 0x0 2. "CONFLICT_CHK_EN,Conflict check enable" "0: Conflict check disable,1: Conflict check enable" newline bitfld.long 0x0 1. "VSELECT,Voltage selection" "0: Change the voltage to high voltage range around..,1: Change the voltage to low voltage range around.." line.long 0x4 "MMC_BOOT,MMC Boot" hexmask.long.word 0x4 16.--31. 1. "BOOT_BLK_CNT,Stop At Block Gap value of automatic mode" newline bitfld.long 0x4 8. "DISABLE_TIME_OUT,Time out" "0: Enable time out,1: Disable time out" newline bitfld.long 0x4 7. "AUTO_SABG_EN,Auto stop at block gap" "0,1" newline bitfld.long 0x4 6. "BOOT_EN,Boot enable" "0: Fast boot disable,1: Fast boot enable" newline bitfld.long 0x4 5. "BOOT_MODE,Boot mode" "0: Normal boot,1: Alternative boot" newline bitfld.long 0x4 4. "BOOT_ACK,BOOT ACK" "0: No ack,1: Ack" newline hexmask.long.byte 0x4 0.--3. 1. "DTOCV_ACK,Boot ACK time out" line.long 0x8 "VEND_SPEC2,Vendor Specific 2 Register" bitfld.long 0x8 12. "ACMD23_ARGU2_EN,Argument2 register enable for ACMD23" "0: Disable,1: Argument2 register enable for ACMD23 sharing.." newline bitfld.long 0x8 11. "HS400_RD_CLK_STOP_EN,HS400 read clock stop enable" "0,1" newline bitfld.long 0x8 10. "HS400_WR_CLK_STOP_EN,HS400 write clock stop enable" "0,1" newline bitfld.long 0x8 6. "TUNING_CMD_EN,Tuning command enable" "0: Auto tuning circuit does not check the CMD line.,1: Auto tuning circuit checks the CMD line." newline bitfld.long 0x8 5. "TUNING_1bit_EN,Tuning 1bit enable" "0,1" newline bitfld.long 0x8 4. "TUNING_8bit_EN,Tuning 8bit enable" "0,1" newline bitfld.long 0x8 3. "CARD_INT_D3_TEST,Card interrupt detection test" "0: Check the card interrupt only when DATA3 is high.,1: Check the card interrupt by ignoring the status.." line.long 0xC "TUNING_CTRL,Tuning Control" bitfld.long 0xC 24. "STD_TUNING_EN,Standard tuning circuit and procedure enable" "0,1" newline bitfld.long 0xC 20.--22. "TUNING_WINDOW,Data window" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 16.--18. "TUNING_STEP,TUNING_STEP" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 8.--15. 1. "TUNING_COUNTER,Tuning counter" newline bitfld.long 0xC 7. "DIS_CMD_CHK_FOR_STD_TUNING,Disable command check for standard tuning" "0,1" newline hexmask.long.byte 0xC 0.--6. 1. "TUNING_START_TAP,Tuning start" tree.end tree "USDHC2" base ad:0x4041C000 group.long 0x0++0xF line.long 0x0 "DS_ADDR,DMA System Address" hexmask.long 0x0 0.--31. 1. "DS_ADDR,System address" line.long 0x4 "BLK_ATT,Block Attributes" hexmask.long.word 0x4 16.--31. 1. "BLKCNT,Blocks count for current transfer" newline hexmask.long.word 0x4 0.--12. 1. "BLKSIZE,Transfer block size" line.long 0x8 "CMD_ARG,Command Argument" hexmask.long 0x8 0.--31. 1. "CMDARG,Command argument" line.long 0xC "CMD_XFR_TYP,Command Transfer Type" hexmask.long.byte 0xC 24.--29. 1. "CMDINX,Command index" newline bitfld.long 0xC 22.--23. "CMDTYP,Command type" "0: Normal other commands,1: Suspend CMD52 for writing bus suspend in CCCR,2: Resume CMD52 for writing function select in CCCR,3: Abort CMD12 CMD52 for writing I/O Abort in CCCR" newline bitfld.long 0xC 21. "DPSEL,Data present select" "0: No data present,1: Data present" newline bitfld.long 0xC 20. "CICEN,Command index check enable" "0: Disable command index check,1: Enables command index check" newline bitfld.long 0xC 19. "CCCEN,Command CRC check enable" "0: Disables command CRC check,1: Enables command CRC check" newline bitfld.long 0xC 16.--17. "RSPTYP,Response type select" "0: No response,1: Response length 136,2: Response length 48,3: Response length 48 check busy after response" rgroup.long 0x10++0xF line.long 0x0 "CMD_RSP0,Command Response0" hexmask.long 0x0 0.--31. 1. "CMDRSP0,Command response 0" line.long 0x4 "CMD_RSP1,Command Response1" hexmask.long 0x4 0.--31. 1. "CMDRSP1,Command response 1" line.long 0x8 "CMD_RSP2,Command Response2" hexmask.long 0x8 0.--31. 1. "CMDRSP2,Command response 2" line.long 0xC "CMD_RSP3,Command Response3" hexmask.long 0xC 0.--31. 1. "CMDRSP3,Command response 3" group.long 0x20++0x3 line.long 0x0 "DATA_BUFF_ACC_PORT,Data Buffer Access Port" hexmask.long 0x0 0.--31. 1. "DATCONT,Data content" rgroup.long 0x24++0x3 line.long 0x0 "PRES_STATE,Present State" hexmask.long.byte 0x0 24.--31. 1. "DLSL,DATA[7:0] line signal level" newline bitfld.long 0x0 23. "CLSL,CMD line signal level" "0,1" newline bitfld.long 0x0 19. "WPSPL,Write protect switch pin level" "0: Write protected (WP = 1),1: Write enabled (WP = 0)" newline bitfld.long 0x0 18. "CDPL,Card detect pin level" "0: No card present (CD_B = 1),1: Card present (CD_B = 0)" newline bitfld.long 0x0 16. "CINST,Card inserted" "0: Power on reset or no card,1: Card inserted" newline bitfld.long 0x0 15. "TSCD,Tap select change done" "0: Delay cell select change is not finished.,1: Delay cell select change is finished." newline bitfld.long 0x0 12. "RTR,Re-Tuning Request (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Fixed or well tuned sampling clock,1: Sampling clock needs re-tuning" newline bitfld.long 0x0 11. "BREN,Buffer read enable" "0: Read disable,1: Read enable" newline bitfld.long 0x0 10. "BWEN,Buffer write enable" "0: Write disable,1: Write enable" newline bitfld.long 0x0 9. "RTA,Read transfer active" "0: No valid data,1: Transferring data" newline bitfld.long 0x0 8. "WTA,Write transfer active" "0: No valid data,1: Transferring data" newline bitfld.long 0x0 7. "SDOFF,SD clock gated off internally" "0: SD clock is active.,1: SD clock is gated off." newline bitfld.long 0x0 6. "PEROFF,IPG_PERCLK gated off internally" "0: IPG_PERCLK is active.,1: IPG_PERCLK is gated off." newline bitfld.long 0x0 5. "HCKOFF,HCLK gated off internally" "0: HCLK is active.,1: HCLK is gated off." newline bitfld.long 0x0 4. "IPGOFF,Peripheral clock gated off internally" "0: Peripheral clock is active.,1: Peripheral clock is gated off." newline bitfld.long 0x0 3. "SDSTB,SD clock stable" "0: Clock is changing frequency and not stable.,1: Clock is stable." newline bitfld.long 0x0 2. "DLA,Data line active" "0: DATA line inactive,1: DATA line active" newline bitfld.long 0x0 1. "CDIHB,Command Inhibit Data (DATA)" "0: Can issue command that uses the DATA line,1: Cannot issue command that uses the DATA line" newline bitfld.long 0x0 0. "CIHB,Command inhibit (CMD)" "0: Can issue command using only CMD line,1: Cannot issue command" group.long 0x28++0x23 line.long 0x0 "PROT_CTRL,Protocol Control" bitfld.long 0x0 30. "NON_EXACT_BLK_RD,Non-exact block read" "0: The block read is exact block read. Host driver..,1: The block read is non-exact block read. Host.." newline bitfld.long 0x0 26. "WECRM,Wakeup event enable on SD card removal" "0: Disables wakeup event enable on SD card removal,1: Enables wakeup event enable on SD card removal" newline bitfld.long 0x0 25. "WECINS,Wakeup event enable on SD card insertion" "0: Disable wakeup event enable on SD card insertion,1: Enable wakeup event enable on SD card insertion" newline bitfld.long 0x0 24. "WECINT,Wakeup event enable on card interrupt" "0: Disables wakeup event enable on card interrupt,1: Enables wakeup event enable on card interrupt" newline bitfld.long 0x0 20. "RD_DONE_NO_8CLK,Read performed number 8 clock" "0,1" newline bitfld.long 0x0 19. "IABG,Interrupt at block gap" "0: Disables interrupt at block gap,1: Enables interrupt at block gap" newline bitfld.long 0x0 18. "RWCTL,Read wait control" "0: Disables read wait control and stop SD clock at..,1: Enables read wait control and assert read wait.." newline bitfld.long 0x0 17. "CREQ,Continue request" "0: No effect,1: Restart" newline bitfld.long 0x0 16. "SABGREQ,Stop at block gap request" "0: Transfer,1: Stop" newline bitfld.long 0x0 8.--9. "DMASEL,DMA select" "0: No DMA or simple DMA is selected.,1: ADMA1 is selected.,2: ADMA2 is selected.,?" newline bitfld.long 0x0 7. "CDSS,Card detect signal selection" "0: Card detection level is selected (for normal..,1: Card detection test level is selected (for test.." newline bitfld.long 0x0 6. "CDTL,Card detect test level" "0: Card detect test level is 0 no card inserted,1: Card detect test level is 1 card inserted" newline bitfld.long 0x0 4.--5. "EMODE,Endian mode" "0: Big endian mode,1: Half word big endian mode,2: Little endian mode,?" newline bitfld.long 0x0 3. "D3CD,DATA3 as card detection pin" "0: DATA3 does not monitor card insertion,1: DATA3 as card detection pin" newline bitfld.long 0x0 1.--2. "DTW,Data transfer width" "0: 1-bit mode,1: 4-bit mode,2: 8-bit mode,?" line.long 0x4 "SYS_CTRL,System Control" bitfld.long 0x4 28. "RSTT,Reset tuning" "0,1" newline bitfld.long 0x4 27. "INITA,Initialization active" "0,1" newline bitfld.long 0x4 26. "RSTD,Software reset for data line" "0: No reset,1: Reset" newline bitfld.long 0x4 25. "RSTC,Software reset for CMD line" "0: No reset,1: Reset" newline bitfld.long 0x4 24. "RSTA,Software reset for all" "0: No reset,1: Reset" newline bitfld.long 0x4 23. "IPP_RST_N,Hardware reset" "0,1" newline hexmask.long.byte 0x4 16.--19. 1. "DTOCV,Data timeout counter value" newline hexmask.long.byte 0x4 8.--15. 1. "SDCLKFS,SDCLK frequency select" newline hexmask.long.byte 0x4 4.--7. 1. "DVS,Divisor" line.long 0x8 "INT_STATUS,Interrupt Status" eventfld.long 0x8 28. "DMAE,DMA error" "0: No error,1: Error" newline eventfld.long 0x8 26. "TNE,Tuning error: (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0,1" newline eventfld.long 0x8 24. "AC12E,Auto CMD12 error" "0: No error,1: Error" newline eventfld.long 0x8 22. "DEBE,Data end bit error" "0: No error,1: Error" newline eventfld.long 0x8 21. "DCE,Data CRC error" "0: No error,1: Error" newline eventfld.long 0x8 20. "DTOE,Data timeout error" "0: No error,1: Time out" newline eventfld.long 0x8 19. "CIE,Command index error" "0: No error,1: Error" newline eventfld.long 0x8 18. "CEBE,Command end bit error" "0: No error,1: End bit error generated" newline eventfld.long 0x8 17. "CCE,Command CRC error" "0: No error,1: CRC error generated" newline eventfld.long 0x8 16. "CTOE,Command timeout error" "0: No error,1: Time out" newline eventfld.long 0x8 14. "TP,Tuning pass:(only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0,1" newline eventfld.long 0x8 12. "RTE,Re-tuning event: (only for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Re-tuning is not required.,1: Re-tuning should be performed." newline eventfld.long 0x8 8. "CINT,Card interrupt" "0: No card interrupt,1: Generate card interrupt" newline eventfld.long 0x8 7. "CRM,Card removal" "0: Card state unstable or inserted,1: Card removed" newline eventfld.long 0x8 6. "CINS,Card insertion" "0: Card state unstable or removed,1: Card inserted" newline eventfld.long 0x8 5. "BRR,Buffer read ready" "0: Not ready to read buffer,1: Ready to read buffer" newline eventfld.long 0x8 4. "BWR,Buffer write ready" "0: Not ready to write buffer,1: Ready to write buffer" newline eventfld.long 0x8 3. "DINT,DMA interrupt" "0: No DMA interrupt,1: DMA interrupt is generated." newline eventfld.long 0x8 2. "BGE,Block gap event" "0: No block gap event,1: Transaction stopped at block gap" newline eventfld.long 0x8 1. "TC,Transfer complete" "0: Transfer does not complete,1: Transfer complete" newline eventfld.long 0x8 0. "CC,Command complete" "0: Command not complete,1: Command complete" line.long 0xC "INT_STATUS_EN,Interrupt Status Enable" bitfld.long 0xC 28. "DMAESEN,DMA error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 26. "TNESEN,Tuning error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 24. "AC12ESEN,Auto CMD12 error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 22. "DEBESEN,Data end bit error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 21. "DCESEN,Data CRC error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 20. "DTOESEN,Data timeout error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 19. "CIESEN,Command index error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 18. "CEBESEN,Command end bit error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 17. "CCESEN,Command CRC error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 16. "CTOESEN,Command timeout error status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 14. "TPSEN,Tuning pass status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 12. "RTESEN,Re-tuning event status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 8. "CINTSEN,Card interrupt status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 7. "CRMSEN,Card removal status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 6. "CINSSEN,Card insertion status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 5. "BRRSEN,Buffer read ready status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 4. "BWRSEN,Buffer write ready status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 3. "DINTSEN,DMA interrupt status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 2. "BGESEN,Block gap event status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 1. "TCSEN,Transfer complete status enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 0. "CCSEN,Command complete status enable" "0: Masked,1: Enabled" line.long 0x10 "INT_SIGNAL_EN,Interrupt Signal Enable" bitfld.long 0x10 28. "DMAEIEN,DMA error interrupt enable" "0: Masked,1: Enable" newline bitfld.long 0x10 26. "TNEIEN,Tuning error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 24. "AC12EIEN,Auto CMD12 error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 22. "DEBEIEN,Data end bit error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 21. "DCEIEN,Data CRC error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 20. "DTOEIEN,Data timeout error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 19. "CIEIEN,Command index error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 18. "CEBEIEN,Command end bit error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 17. "CCEIEN,Command CRC error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 16. "CTOEIEN,Command timeout error interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 14. "TPIEN,Tuning Pass interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 12. "RTEIEN,Re-tuning event interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 8. "CINTIEN,Card interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 7. "CRMIEN,Card removal interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 6. "CINSIEN,Card insertion interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 5. "BRRIEN,Buffer read ready interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 4. "BWRIEN,Buffer write ready interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 3. "DINTIEN,DMA interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 2. "BGEIEN,Block gap event interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 1. "TCIEN,Transfer complete interrupt enable" "0: Masked,1: Enabled" newline bitfld.long 0x10 0. "CCIEN,Command complete interrupt enable" "0: Masked,1: Enabled" line.long 0x14 "AUTOCMD12_ERR_STATUS,Auto CMD12 Error Status" bitfld.long 0x14 23. "SMP_CLK_SEL,Sample clock select" "0: Fixed clock is used to sample data,1: Tuned clock is used to sample data" newline bitfld.long 0x14 22. "EXECUTE_TUNING,Execute tuning" "0: Tuning procedure is aborted,1: Start tuning procedure" newline rbitfld.long 0x14 7. "CNIBAC12E,Command not issued by Auto CMD12 error" "0: No error,1: Not issued" newline rbitfld.long 0x14 4. "AC12IE,Auto CMD12 / 23 index error" "0: No error,1: Error the CMD index in response is not CMD12/23" newline rbitfld.long 0x14 3. "AC12CE,Auto CMD12 / 23 CRC error" "0: No CRC error,1: CRC error met in Auto CMD12/23 response" newline rbitfld.long 0x14 2. "AC12EBE,Auto CMD12 / 23 end bit error" "0: No error,1: End bit error generated" newline rbitfld.long 0x14 1. "AC12TOE,Auto CMD12 / 23 timeout error" "0: No error,1: Time out" newline rbitfld.long 0x14 0. "AC12NE,Auto CMD12 not executed" "0: Executed,1: Not executed" line.long 0x18 "HOST_CTRL_CAP,Host Controller Capabilities" rbitfld.long 0x18 26. "VS18,Voltage support 1.8 V" "0: 1.8 V not supported,1: 1.8 V supported" newline rbitfld.long 0x18 25. "VS30,Voltage support 3.0 V" "0: 3.0 V not supported,1: 3.0 V supported" newline rbitfld.long 0x18 24. "VS33,Voltage support 3.3 V" "0: 3.3 V not supported,1: 3.3 V supported" newline rbitfld.long 0x18 23. "SRS,Suspend / resume support" "0: Not supported,1: Supported" newline rbitfld.long 0x18 22. "DMAS,DMA support" "0: DMA not supported,1: DMA supported" newline rbitfld.long 0x18 21. "HSS,High speed support" "0: High speed not supported,1: High speed supported" newline rbitfld.long 0x18 20. "ADMAS,ADMA support" "0: Advanced DMA not supported,1: Advanced DMA supported" newline rbitfld.long 0x18 16.--18. "MBL,Max block length" "0: 512 bytes,1: 1024 bytes,2: 2048 bytes,3: 4096 bytes,?,?,?,?" newline bitfld.long 0x18 13. "USE_TUNING_SDR50,Use Tuning for SDR50" "0: SDR50 does not support tuning,1: SDR50 supports tuning" newline rbitfld.long 0x18 2. "DDR50_SUPPORT,DDR50 support" "0,1" newline rbitfld.long 0x18 1. "SDR104_SUPPORT,SDR104 support" "0,1" newline rbitfld.long 0x18 0. "SDR50_SUPPORT,SDR50 support" "0,1" line.long 0x1C "WTMK_LVL,Watermark Level" hexmask.long.byte 0x1C 16.--23. 1. "WR_WML,Write watermark level" newline hexmask.long.byte 0x1C 0.--7. 1. "RD_WML,Read watermark level" line.long 0x20 "MIX_CTRL,Mixer Control" bitfld.long 0x20 26. "HS400_MODE,Enable HS400 mode" "0,1" newline bitfld.long 0x20 25. "FBCLK_SEL,Feedback clock source selection (Only used for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Feedback clock comes from the loopback CLK,1: Feedback clock comes from the ipp_card_clk_out" newline bitfld.long 0x20 24. "AUTO_TUNE_EN,Auto tuning enable (Only used for SD3.0 SDR104 mode and and EMMC HS200 mode)" "0: Disable auto tuning,1: Enable auto tuning" newline bitfld.long 0x20 23. "SMP_CLK_SEL,Clock selection" "0: Fixed clock is used to sample data / cmd,1: Tuned clock is used to sample data / cmd" newline bitfld.long 0x20 22. "EXE_TUNE,Execute tuning: (Only used for SD3.0 SDR104 mode and EMMC HS200 mode)" "0: Not tuned or tuning completed,1: Execute tuning" newline bitfld.long 0x20 7. "AC23EN,Auto CMD23 enable" "0,1" newline bitfld.long 0x20 6. "NIBBLE_POS,Nibble position indication" "0,1" newline bitfld.long 0x20 5. "MSBSEL,Multi / Single block select" "0: Single block,1: Multiple blocks" newline bitfld.long 0x20 4. "DTDSEL,Data transfer direction select" "0: Write (Host to card),1: Read (Card to host)" newline bitfld.long 0x20 3. "DDR_EN,Dual data rate mode selection" "0,1" newline bitfld.long 0x20 2. "AC12EN,Auto CMD12 enable" "0: Disable,1: Enable" newline bitfld.long 0x20 1. "BCEN,Block count enable" "0: Disable,1: Enable" newline bitfld.long 0x20 0. "DMAEN,DMA enable" "0: Disable,1: Enable" group.long 0x50++0x3 line.long 0x0 "FORCE_EVENT,Force Event" bitfld.long 0x0 31. "FEVTCINT,Force event card interrupt" "0,1" newline bitfld.long 0x0 28. "FEVTDMAE,Force event DMA error" "0,1" newline bitfld.long 0x0 26. "FEVTTNE,Force tuning error" "0,1" newline bitfld.long 0x0 24. "FEVTAC12E,Force event Auto Command 12 error" "0,1" newline bitfld.long 0x0 22. "FEVTDEBE,Force event data end bit error" "0,1" newline bitfld.long 0x0 21. "FEVTDCE,Force event data CRC error" "0,1" newline bitfld.long 0x0 20. "FEVTDTOE,Force event data time out error" "0,1" newline bitfld.long 0x0 19. "FEVTCIE,Force event command index error" "0,1" newline bitfld.long 0x0 18. "FEVTCEBE,Force event command end bit error" "0,1" newline bitfld.long 0x0 17. "FEVTCCE,Force event command CRC error" "0,1" newline bitfld.long 0x0 16. "FEVTCTOE,Force event command time out error" "0,1" newline bitfld.long 0x0 7. "FEVTCNIBAC12E,Force event command not executed by Auto Command 12 error" "0,1" newline bitfld.long 0x0 4. "FEVTAC12IE,Force event Auto Command 12 index error" "0,1" newline bitfld.long 0x0 3. "FEVTAC12EBE,Force event Auto Command 12 end bit error" "0,1" newline bitfld.long 0x0 2. "FEVTAC12CE,Force event auto command 12 CRC error" "0,1" newline bitfld.long 0x0 1. "FEVTAC12TOE,Force event auto command 12 time out error" "0,1" newline bitfld.long 0x0 0. "FEVTAC12NE,Force event auto command 12 not executed" "0,1" rgroup.long 0x54++0x3 line.long 0x0 "ADMA_ERR_STATUS,ADMA Error Status" bitfld.long 0x0 3. "ADMADCE,ADMA descriptor error" "0: No error,1: Error" newline bitfld.long 0x0 2. "ADMALME,ADMA length mismatch error" "0: No error,1: Error" newline bitfld.long 0x0 0.--1. "ADMAES,ADMA error state (when ADMA error is occurred)" "0,1,2,3" group.long 0x58++0x3 line.long 0x0 "ADMA_SYS_ADDR,ADMA System Address" hexmask.long 0x0 2.--31. 1. "ADS_ADDR,ADMA system address" group.long 0x60++0x3 line.long 0x0 "DLL_CTRL,DLL (Delay Line) Control" hexmask.long.byte 0x0 28.--31. 1. "DLL_CTRL_REF_UPDATE_INT,DLL control loop update interval" newline hexmask.long.byte 0x0 20.--27. 1. "DLL_CTRL_SLV_UPDATE_INT,Slave delay line update interval" newline bitfld.long 0x0 16.--18. "DLL_CTRL_SLV_DLY_TARGET1,DLL slave delay target1" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0x0 9.--15. 1. "DLL_CTRL_SLV_OVERRIDE_VAL,DLL slave override val" newline bitfld.long 0x0 8. "DLL_CTRL_SLV_OVERRIDE,DLL slave override" "0,1" newline bitfld.long 0x0 7. "DLL_CTRL_GATE_UPDATE,DLL gate update" "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "DLL_CTRL_SLV_DLY_TARGET0,DLL slave delay target0" newline bitfld.long 0x0 2. "DLL_CTRL_SLV_FORCE_UPD,DLL slave delay line" "0,1" newline bitfld.long 0x0 1. "DLL_CTRL_RESET,DLL reset" "0,1" newline bitfld.long 0x0 0. "DLL_CTRL_ENABLE,DLL and delay chain" "0,1" rgroup.long 0x64++0x3 line.long 0x0 "DLL_STATUS,DLL Status" hexmask.long.byte 0x0 9.--15. 1. "DLL_STS_REF_SEL,Reference delay line select taps" newline hexmask.long.byte 0x0 2.--8. 1. "DLL_STS_SLV_SEL,Slave delay line select status" newline bitfld.long 0x0 1. "DLL_STS_REF_LOCK,Reference DLL lock status" "0,1" newline bitfld.long 0x0 0. "DLL_STS_SLV_LOCK,Slave delay-line lock status" "0,1" group.long 0x68++0x3 line.long 0x0 "CLK_TUNE_CTRL_STATUS,CLK Tuning Control and Status" rbitfld.long 0x0 31. "PRE_ERR,PRE error" "0,1" newline hexmask.long.byte 0x0 24.--30. 1. "TAP_SEL_PRE,TAP_SEL_PRE" newline hexmask.long.byte 0x0 20.--23. 1. "TAP_SEL_OUT,Delay cells added on the feedback clock between CLK_PRE and CLK_OUT" newline hexmask.long.byte 0x0 16.--19. 1. "TAP_SEL_POST,Delay cells added on the feedback clock between CLK_OUT and CLK_POST" newline rbitfld.long 0x0 15. "NXT_ERR,NXT error" "0,1" newline hexmask.long.byte 0x0 8.--14. 1. "DLY_CELL_SET_PRE,delay cells on the feedback clock between the feedback clock and CLK_PRE" newline hexmask.long.byte 0x0 4.--7. 1. "DLY_CELL_SET_OUT,Delay cells on the feedback clock between CLK_PRE and CLK_OUT" newline hexmask.long.byte 0x0 0.--3. 1. "DLY_CELL_SET_POST,Delay cells on the feedback clock between CLK_OUT and CLK_POST" group.long 0x70++0x3 line.long 0x0 "STROBE_DLL_CTRL,Strobe DLL control" hexmask.long.byte 0x0 28.--31. 1. "STROBE_DLL_CTRL_REF_UPDATE_INT,Strobe DLL control reference update interval" newline hexmask.long.byte 0x0 20.--27. 1. "STROBE_DLL_CTRL_SLV_UPDATE_INT,Strobe DLL control slave update interval" newline hexmask.long.byte 0x0 9.--15. 1. "STROBE_DLL_CTRL_SLV_OVERRIDE_VAL,Strobe DLL control slave Override value" newline bitfld.long 0x0 8. "STROBE_DLL_CTRL_SLV_OVERRIDE,Strobe DLL control slave override" "0,1" newline bitfld.long 0x0 7. "STROBE_DLL_CTRL_GATE_UPDATE,Strobe DLL control gate update" "0,1" newline hexmask.long.byte 0x0 3.--6. 1. "STROBE_DLL_CTRL_SLV_DLY_TARGET,Strobe DLL Control Slave Delay Target" newline bitfld.long 0x0 2. "STROBE_DLL_CTRL_SLV_FORCE_UPD,Strobe DLL control slave force updated" "0,1" newline bitfld.long 0x0 1. "STROBE_DLL_CTRL_RESET,Strobe DLL control reset" "0,1" newline bitfld.long 0x0 0. "STROBE_DLL_CTRL_ENABLE,Strobe DLL control enable" "0,1" rgroup.long 0x74++0x3 line.long 0x0 "STROBE_DLL_STATUS,Strobe DLL status" hexmask.long.byte 0x0 9.--15. 1. "STROBE_DLL_STS_REF_SEL,Strobe DLL status reference select" newline hexmask.long.byte 0x0 2.--8. 1. "STROBE_DLL_STS_SLV_SEL,Strobe DLL status slave select" newline bitfld.long 0x0 1. "STROBE_DLL_STS_REF_LOCK,Strobe DLL status reference lock" "0,1" newline bitfld.long 0x0 0. "STROBE_DLL_STS_SLV_LOCK,Strobe DLL status slave lock" "0,1" group.long 0xC0++0xF line.long 0x0 "VEND_SPEC,Vendor Specific Register" bitfld.long 0x0 31. "CMD_BYTE_EN,Byte access" "0: Disable,1: Enable" newline bitfld.long 0x0 15. "CRC_CHK_DIS,CRC Check Disable" "0: Check CRC16 for every read data packet and check..,1: Ignore CRC16 check for every read data packet.." newline bitfld.long 0x0 8. "FRC_SDCLK_ON,Force CLK" "0: CLK active or inactive is fully controlled by..,1: Force CLK active" newline bitfld.long 0x0 3. "AC12_WR_CHKBUSY_EN,Check busy enable" "0: Do not check busy after auto CMD12 for write..,1: Check busy after auto CMD12 for write data packet" newline bitfld.long 0x0 2. "CONFLICT_CHK_EN,Conflict check enable" "0: Conflict check disable,1: Conflict check enable" newline bitfld.long 0x0 1. "VSELECT,Voltage selection" "0: Change the voltage to high voltage range around..,1: Change the voltage to low voltage range around.." line.long 0x4 "MMC_BOOT,MMC Boot" hexmask.long.word 0x4 16.--31. 1. "BOOT_BLK_CNT,Stop At Block Gap value of automatic mode" newline bitfld.long 0x4 8. "DISABLE_TIME_OUT,Time out" "0: Enable time out,1: Disable time out" newline bitfld.long 0x4 7. "AUTO_SABG_EN,Auto stop at block gap" "0,1" newline bitfld.long 0x4 6. "BOOT_EN,Boot enable" "0: Fast boot disable,1: Fast boot enable" newline bitfld.long 0x4 5. "BOOT_MODE,Boot mode" "0: Normal boot,1: Alternative boot" newline bitfld.long 0x4 4. "BOOT_ACK,BOOT ACK" "0: No ack,1: Ack" newline hexmask.long.byte 0x4 0.--3. 1. "DTOCV_ACK,Boot ACK time out" line.long 0x8 "VEND_SPEC2,Vendor Specific 2 Register" bitfld.long 0x8 12. "ACMD23_ARGU2_EN,Argument2 register enable for ACMD23" "0: Disable,1: Argument2 register enable for ACMD23 sharing.." newline bitfld.long 0x8 11. "HS400_RD_CLK_STOP_EN,HS400 read clock stop enable" "0,1" newline bitfld.long 0x8 10. "HS400_WR_CLK_STOP_EN,HS400 write clock stop enable" "0,1" newline bitfld.long 0x8 6. "TUNING_CMD_EN,Tuning command enable" "0: Auto tuning circuit does not check the CMD line.,1: Auto tuning circuit checks the CMD line." newline bitfld.long 0x8 5. "TUNING_1bit_EN,Tuning 1bit enable" "0,1" newline bitfld.long 0x8 4. "TUNING_8bit_EN,Tuning 8bit enable" "0,1" newline bitfld.long 0x8 3. "CARD_INT_D3_TEST,Card interrupt detection test" "0: Check the card interrupt only when DATA3 is high.,1: Check the card interrupt by ignoring the status.." line.long 0xC "TUNING_CTRL,Tuning Control" bitfld.long 0xC 24. "STD_TUNING_EN,Standard tuning circuit and procedure enable" "0,1" newline bitfld.long 0xC 20.--22. "TUNING_WINDOW,Data window" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 16.--18. "TUNING_STEP,TUNING_STEP" "0,1,2,3,4,5,6,7" newline hexmask.long.byte 0xC 8.--15. 1. "TUNING_COUNTER,Tuning counter" newline bitfld.long 0xC 7. "DIS_CMD_CHK_FOR_STD_TUNING,Disable command check for standard tuning" "0,1" newline hexmask.long.byte 0xC 0.--6. 1. "TUNING_START_TAP,Tuning start" tree.end tree.end tree "VIDEO" base ad:0x0 tree "VIDEO_MUX" base ad:0x40818000 group.long 0x0++0xF line.long 0x0 "VID_MUX_CTRL,Video mux Control Register" bitfld.long 0x0 3. "PARA_LCD_SEL,Parallel LCDIF video data input mux selector" "0: Parallel LCDIF video data is from eLCDIF,1: Parallel LCDIF video data is from LCDIFv2" bitfld.long 0x0 2. "MIPI_DSI_SEL,MIPI DSI video data input mux selector" "0: MIPI DSI video data is from eLCDIF,1: MIPI DSI video data is from LCDIFv2" newline bitfld.long 0x0 1. "LCDIF2_SEL,LCDIF2 sensor data input mux selector" "0: LCDIFv2 sensor data is from Parallel CSI,1: LCDIFv2 sensor data is from MIPI CSI" bitfld.long 0x0 0. "CSI_SEL,CSI sensor data input mux selector" "0: CSI sensor data is from Parallel CSI,1: CSI sensor data is from MIPI CSI" line.long 0x4 "VID_MUX_CTRL_SET,Video mux Control Register" bitfld.long 0x4 3. "PARA_LCD_SEL,Parallel LCDIF video data input mux selector" "0,1" bitfld.long 0x4 2. "MIPI_DSI_SEL,MIPI DSI video data input mux selector" "0,1" newline bitfld.long 0x4 1. "LCDIF2_SEL,LCDIF2 sensor data input mux selector" "0,1" bitfld.long 0x4 0. "CSI_SEL,CSI sensor data input mux selector" "0,1" line.long 0x8 "VID_MUX_CTRL_CLR,Video mux Control Register" eventfld.long 0x8 3. "PARA_LCD_SEL,Parallel LCDIF video data input mux selector" "0,1" eventfld.long 0x8 2. "MIPI_DSI_SEL,MIPI DSI video data input mux selector" "0,1" newline eventfld.long 0x8 1. "LCDIF2_SEL,LCDIF2 sensor data input mux selector" "0,1" eventfld.long 0x8 0. "CSI_SEL,CSI sensor data input mux selector" "0,1" line.long 0xC "VID_MUX_CTRL_TOG,Video mux Control Register" bitfld.long 0xC 3. "PARA_LCD_SEL,Parallel LCDIF video data input mux selector" "0,1" bitfld.long 0xC 2. "MIPI_DSI_SEL,MIPI DSI video data input mux selector" "0,1" newline bitfld.long 0xC 1. "LCDIF2_SEL,LCDIF2 sensor data input mux selector" "0,1" bitfld.long 0xC 0. "CSI_SEL,CSI sensor data input mux selector" "0,1" group.long 0x20++0x1F line.long 0x0 "PLM_CTRL,Pixel Link Master(PLM) Control Register" bitfld.long 0x0 4. "POLARITY,Polarity of HYSNC/VSYNC" "0: Keep the current polarity of HSYNC and VSYNC,1: Invert the polarity of HSYNC and VSYNC" bitfld.long 0x0 3. "VALID_OVERRIDE,Valid override" "0: HSYNC and VSYNC is asserted,1: HSYNC and VSYNC is not asserted" newline bitfld.long 0x0 2. "HSYNC_OVERRIDE,HSYNC override" "0: HSYNC is not asserted,1: HSYNC is asserted" bitfld.long 0x0 1. "VSYNC_OVERRIDE,VSYNC override" "0: VSYNC is not asserted,1: VSYNC is asserted" newline bitfld.long 0x0 0. "ENABLE,Enable the output of HYSNC and VSYNC" "0: No active HSYNC and VSYNC output,1: Active HSYNC and VSYNC output" line.long 0x4 "PLM_CTRL_SET,Pixel Link Master(PLM) Control Register" bitfld.long 0x4 4. "POLARITY,Polarity of HYSNC/VSYNC" "0,1" bitfld.long 0x4 3. "VALID_OVERRIDE,Valid override" "0,1" newline bitfld.long 0x4 2. "HSYNC_OVERRIDE,HSYNC override" "0,1" bitfld.long 0x4 1. "VSYNC_OVERRIDE,VSYNC override" "0,1" newline bitfld.long 0x4 0. "ENABLE,Enable the output of HYSNC and VSYNC" "0,1" line.long 0x8 "PLM_CTRL_CLR,Pixel Link Master(PLM) Control Register" eventfld.long 0x8 4. "POLARITY,Polarity of HYSNC/VSYNC" "0,1" eventfld.long 0x8 3. "VALID_OVERRIDE,Valid override" "0,1" newline eventfld.long 0x8 2. "HSYNC_OVERRIDE,HSYNC override" "0,1" eventfld.long 0x8 1. "VSYNC_OVERRIDE,VSYNC override" "0,1" newline eventfld.long 0x8 0. "ENABLE,Enable the output of HYSNC and VSYNC" "0,1" line.long 0xC "PLM_CTRL_TOG,Pixel Link Master(PLM) Control Register" bitfld.long 0xC 4. "POLARITY,Polarity of HYSNC/VSYNC" "0,1" bitfld.long 0xC 3. "VALID_OVERRIDE,Valid override" "0,1" newline bitfld.long 0xC 2. "HSYNC_OVERRIDE,HSYNC override" "0,1" bitfld.long 0xC 1. "VSYNC_OVERRIDE,VSYNC override" "0,1" newline bitfld.long 0xC 0. "ENABLE,Enable the output of HYSNC and VSYNC" "0,1" line.long 0x10 "YUV420_CTRL,YUV420 Control Register" bitfld.long 0x10 0. "FST_LN_DATA_TYPE,Data type of First Line" "0: Odd (default),1: Even" line.long 0x14 "YUV420_CTRL_SET,YUV420 Control Register" bitfld.long 0x14 0. "FST_LN_DATA_TYPE,Data type of First Line" "0,1" line.long 0x18 "YUV420_CTRL_CLR,YUV420 Control Register" eventfld.long 0x18 0. "FST_LN_DATA_TYPE,Data type of First Line" "0,1" line.long 0x1C "YUV420_CTRL_TOG,YUV420 Control Register" bitfld.long 0x1C 0. "FST_LN_DATA_TYPE,Data type of First Line" "0,1" group.long 0x50++0xF line.long 0x0 "CFG_DT_DISABLE,Data Disable Register" hexmask.long.tbyte 0x0 0.--23. 1. "CFG_DT_DISABLE,Data Type Disable" line.long 0x4 "CFG_DT_DISABLE_SET,Data Disable Register" hexmask.long.tbyte 0x4 0.--23. 1. "CFG_DT_DISABLE,Data Type Disable" line.long 0x8 "CFG_DT_DISABLE_CLR,Data Disable Register" hexmask.long.tbyte 0x8 0.--23. 1. "CFG_DT_DISABLE,Data Type Disable" line.long 0xC "CFG_DT_DISABLE_TOG,Data Disable Register" hexmask.long.tbyte 0xC 0.--23. 1. "CFG_DT_DISABLE,Data Type Disable" group.long 0x70++0xF line.long 0x0 "MIPI_DSI_CTRL,MIPI DSI Control Register" bitfld.long 0x0 1. "DPI_CM,Color Mode control" "0: Normal Mode,1: Low-color mode" bitfld.long 0x0 0. "DPI_SD,Shut Down - Control to shutdown display (type 4 only)" "0: No effect,1: Send shutdown command" line.long 0x4 "MIPI_DSI_CTRL_SET,MIPI DSI Control Register" bitfld.long 0x4 1. "DPI_CM,Color Mode control" "0,1" bitfld.long 0x4 0. "DPI_SD,Shut Down - Control to shutdown display (type 4 only)" "0,1" line.long 0x8 "MIPI_DSI_CTRL_CLR,MIPI DSI Control Register" eventfld.long 0x8 1. "DPI_CM,Color Mode control" "0,1" eventfld.long 0x8 0. "DPI_SD,Shut Down - Control to shutdown display (type 4 only)" "0,1" line.long 0xC "MIPI_DSI_CTRL_TOG,MIPI DSI Control Register" bitfld.long 0xC 1. "DPI_CM,Color Mode control" "0,1" bitfld.long 0xC 0. "DPI_SD,Shut Down - Control to shutdown display (type 4 only)" "0,1" tree.end base ad:0x0 tree "VIDEO_PLL" group.long 0x0++0x3F line.long 0x0 "CTRL0,Fractional PLL Control Register" bitfld.long 0x0 29. "BIAS_SELECT,BIAS_SELECT" "0: Used in SoCs with a bias current of 10uA,1: Used in SoCs with a bias current of 2uA" bitfld.long 0x0 25.--27. "POST_DIV_SEL,Post Divide Select" "0: Divide by 1,1: Divide by 2,2: Divide by 4,3: Divide by 8,4: Divide by 16,5: Divide by 32,?,?" newline bitfld.long 0x0 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x0 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 17. "DITHER_EN,DITHER_EN" "0: Disable Dither,1: Enable Dither" bitfld.long 0x0 16. "BYPASS,BYPASS" "0: No Bypass,1: Bypass the PLL" newline bitfld.long 0x0 15. "ENABLE,ENABLE" "0: Disable the clock output,1: Enable the clock output" bitfld.long 0x0 14. "POWERUP,POWERUP" "0: Power down the PLL,1: Power Up the PLL" newline bitfld.long 0x0 13. "HOLD_RING_OFF,PLL Start up initialization" "0: Normal operation,1: Initialize PLL start up" bitfld.long 0x0 8. "ENABLE_ALT,ENABLE_ALT" "0: Disable the alternate clock output,1: Enable the alternate clock output which is the.." newline hexmask.long.byte 0x0 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x4 "CTRL0_SET,Fractional PLL Control Register" bitfld.long 0x4 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0x4 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0x4 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0x4 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0x4 15. "ENABLE,ENABLE" "0,1" bitfld.long 0x4 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0x4 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0x4 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x4 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x8 "CTRL0_CLR,Fractional PLL Control Register" eventfld.long 0x8 29. "BIAS_SELECT,BIAS_SELECT" "0,1" eventfld.long 0x8 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 22. "PLL_REG_EN,PLL_REG_EN" "0,1" eventfld.long 0x8 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline eventfld.long 0x8 17. "DITHER_EN,DITHER_EN" "0,1" eventfld.long 0x8 16. "BYPASS,BYPASS" "0,1" newline eventfld.long 0x8 15. "ENABLE,ENABLE" "0,1" eventfld.long 0x8 14. "POWERUP,POWERUP" "0,1" newline eventfld.long 0x8 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" eventfld.long 0x8 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0x8 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0xC "CTRL0_TOG,Fractional PLL Control Register" bitfld.long 0xC 29. "BIAS_SELECT,BIAS_SELECT" "0,1" bitfld.long 0xC 25.--27. "POST_DIV_SEL,Post Divide Select" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 22. "PLL_REG_EN,PLL_REG_EN" "0,1" bitfld.long 0xC 19.--21. "BIAS_TRIM,BIAS_TRIM" "0,1,2,3,4,5,6,7" newline bitfld.long 0xC 17. "DITHER_EN,DITHER_EN" "0,1" bitfld.long 0xC 16. "BYPASS,BYPASS" "0,1" newline bitfld.long 0xC 15. "ENABLE,ENABLE" "0,1" bitfld.long 0xC 14. "POWERUP,POWERUP" "0,1" newline bitfld.long 0xC 13. "HOLD_RING_OFF,PLL Start up initialization" "0,1" bitfld.long 0xC 8. "ENABLE_ALT,ENABLE_ALT" "0,1" newline hexmask.long.byte 0xC 0.--6. 1. "DIV_SELECT,DIV_SELECT" line.long 0x10 "SPREAD_SPECTRUM,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x10 16.--31. 1. "STOP,Stop" bitfld.long 0x10 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x10 0.--14. 1. "STEP,Step" line.long 0x14 "SPREAD_SPECTRUM_SET,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x14 16.--31. 1. "STOP,Stop" bitfld.long 0x14 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x14 0.--14. 1. "STEP,Step" line.long 0x18 "SPREAD_SPECTRUM_CLR,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x18 16.--31. 1. "STOP,Stop" eventfld.long 0x18 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x18 0.--14. 1. "STEP,Step" line.long 0x1C "SPREAD_SPECTRUM_TOG,Fractional PLL Spread Spectrum Control Register" hexmask.long.word 0x1C 16.--31. 1. "STOP,Stop" bitfld.long 0x1C 15. "ENABLE,Enable" "0,1" newline hexmask.long.word 0x1C 0.--14. 1. "STEP,Step" line.long 0x20 "NUMERATOR,Fractional PLL Numerator Control Register" hexmask.long 0x20 0.--29. 1. "NUM,Numerator" line.long 0x24 "NUMERATOR_SET,Fractional PLL Numerator Control Register" hexmask.long 0x24 0.--29. 1. "NUM,Numerator" line.long 0x28 "NUMERATOR_CLR,Fractional PLL Numerator Control Register" hexmask.long 0x28 0.--29. 1. "NUM,Numerator" line.long 0x2C "NUMERATOR_TOG,Fractional PLL Numerator Control Register" hexmask.long 0x2C 0.--29. 1. "NUM,Numerator" line.long 0x30 "DENOMINATOR,Fractional PLL Denominator Control Register" hexmask.long 0x30 0.--29. 1. "DENOM,Denominator" line.long 0x34 "DENOMINATOR_SET,Fractional PLL Denominator Control Register" hexmask.long 0x34 0.--29. 1. "DENOM,Denominator" line.long 0x38 "DENOMINATOR_CLR,Fractional PLL Denominator Control Register" hexmask.long 0x38 0.--29. 1. "DENOM,Denominator" line.long 0x3C "DENOMINATOR_TOG,Fractional PLL Denominator Control Register" hexmask.long 0x3C 0.--29. 1. "DENOM,Denominator" tree.end tree.end tree "VMBANDGAP" base ad:0x0 group.long 0x0++0xF line.long 0x0 "CTRL0,Analog Control Register CTRL0" bitfld.long 0x0 4. "REFTOP_SELFBIASOFF,bandgap self-bias control bit" "0,1" bitfld.long 0x0 3. "REFTOP_LOWPOWER,Low-power control bit" "0,1" bitfld.long 0x0 2. "REFTOP_PWDVBGUP,Power-down VBGUP detector in bandgap" "0,1" bitfld.long 0x0 1. "REFTOP_LINREGREF_PWD,Power-down for bandgap voltage-reference buffer" "0,1" bitfld.long 0x0 0. "REFTOP_PWD,Master power-down for bandgap module" "0,1" line.long 0x4 "CTRL0_SET,Analog Control Register CTRL0" bitfld.long 0x4 4. "REFTOP_SELFBIASOFF,bandgap self-bias control bit" "0,1" bitfld.long 0x4 3. "REFTOP_LOWPOWER,Low-power control bit" "0,1" bitfld.long 0x4 2. "REFTOP_PWDVBGUP,Power-down VBGUP detector in bandgap" "0,1" bitfld.long 0x4 1. "REFTOP_LINREGREF_PWD,Power-down for bandgap voltage-reference buffer" "0,1" bitfld.long 0x4 0. "REFTOP_PWD,Master power-down for bandgap module" "0,1" line.long 0x8 "CTRL0_CLR,Analog Control Register CTRL0" eventfld.long 0x8 4. "REFTOP_SELFBIASOFF,bandgap self-bias control bit" "0,1" eventfld.long 0x8 3. "REFTOP_LOWPOWER,Low-power control bit" "0,1" eventfld.long 0x8 2. "REFTOP_PWDVBGUP,Power-down VBGUP detector in bandgap" "0,1" eventfld.long 0x8 1. "REFTOP_LINREGREF_PWD,Power-down for bandgap voltage-reference buffer" "0,1" eventfld.long 0x8 0. "REFTOP_PWD,Master power-down for bandgap module" "0,1" line.long 0xC "CTRL0_TOG,Analog Control Register CTRL0" bitfld.long 0xC 4. "REFTOP_SELFBIASOFF,bandgap self-bias control bit" "0,1" bitfld.long 0xC 3. "REFTOP_LOWPOWER,Low-power control bit" "0,1" bitfld.long 0xC 2. "REFTOP_PWDVBGUP,Power-down VBGUP detector in bandgap" "0,1" bitfld.long 0xC 1. "REFTOP_LINREGREF_PWD,Power-down for bandgap voltage-reference buffer" "0,1" bitfld.long 0xC 0. "REFTOP_PWD,Master power-down for bandgap module" "0,1" rgroup.long 0x50++0xF line.long 0x0 "STAT0,Analog Status Register STAT0" bitfld.long 0x0 3. "VDD3_PORB,Brief description here" "0,1" bitfld.long 0x0 2. "VDD2_PORB,Brief description here" "0,1" bitfld.long 0x0 1. "VDD1_PORB,Brief description here" "0,1" bitfld.long 0x0 0. "REFTOP_VBGUP,Brief description here" "0,1" line.long 0x4 "STAT0_SET,Analog Status Register STAT0" bitfld.long 0x4 3. "VDD3_PORB,Brief description here" "0,1" bitfld.long 0x4 2. "VDD2_PORB,Brief description here" "0,1" bitfld.long 0x4 1. "VDD1_PORB,Brief description here" "0,1" bitfld.long 0x4 0. "REFTOP_VBGUP,Brief description here" "0,1" line.long 0x8 "STAT0_CLR,Analog Status Register STAT0" eventfld.long 0x8 3. "VDD3_PORB,Brief description here" "0,1" eventfld.long 0x8 2. "VDD2_PORB,Brief description here" "0,1" eventfld.long 0x8 1. "VDD1_PORB,Brief description here" "0,1" eventfld.long 0x8 0. "REFTOP_VBGUP,Brief description here" "0,1" line.long 0xC "STAT0_TOG,Analog Status Register STAT0" bitfld.long 0xC 3. "VDD3_PORB,Brief description here" "0,1" bitfld.long 0xC 2. "VDD2_PORB,Brief description here" "0,1" bitfld.long 0xC 1. "VDD1_PORB,Brief description here" "0,1" bitfld.long 0xC 0. "REFTOP_VBGUP,Brief description here" "0,1" tree.end tree "WDOG" base ad:0x0 tree "WDOG1" base ad:0x40030000 group.word 0x0++0x3 line.word 0x0 "WCR,Watchdog Control Register" hexmask.word.byte 0x0 8.--15. 1. "WT,WT" bitfld.word 0x0 7. "WDW,WDW" "0: Continue WDOG timer operation (Default).,1: Suspend WDOG timer operation." newline bitfld.word 0x0 6. "SRE,Software Reset Extension an optional way to generate software reset" "0: using original way to generate software reset..,1: using new way to generate software reset." bitfld.word 0x0 5. "WDA,WDA" "0: Assert WDOG_B output.,1: No effect on system (Default)." newline bitfld.word 0x0 4. "SRS,SRS" "0: Assert system reset signal.,1: No effect on the system (Default)." bitfld.word 0x0 3. "WDT,WDT" "0: No effect on WDOG_B (Default).,1: Assert WDOG_B upon a Watchdog Time-out event." newline bitfld.word 0x0 2. "WDE,WDE" "0: Disable the Watchdog (Default).,1: Enable the Watchdog." bitfld.word 0x0 1. "WDBG,WDBG" "0: Continue WDOG timer operation (Default).,1: Suspend the watchdog timer." newline bitfld.word 0x0 0. "WDZST,WDZST" "0: Continue timer operation (Default).,1: Suspend the watchdog timer." line.word 0x2 "WSR,Watchdog Service Register" hexmask.word 0x2 0.--15. 1. "WSR,WSR" rgroup.word 0x4++0x1 line.word 0x0 "WRSR,Watchdog Reset Status Register" bitfld.word 0x0 4. "POR,POR" "0: Reset is not the result of a power on reset.,1: Reset is the result of a power on reset." bitfld.word 0x0 1. "TOUT,TOUT" "0: Reset is not the result of a WDOG timeout.,1: Reset is the result of a WDOG timeout." newline bitfld.word 0x0 0. "SFTW,SFTW" "0: Reset is not the result of a software reset.,1: Reset is the result of a software reset." group.word 0x6++0x3 line.word 0x0 "WICR,Watchdog Interrupt Control Register" bitfld.word 0x0 15. "WIE,WIE" "0: Disable Interrupt (Default).,1: Enable Interrupt." eventfld.word 0x0 14. "WTIS,WTIS" "0: No interrupt has occurred (Default).,1: Interrupt has occurred" newline hexmask.word.byte 0x0 0.--7. 1. "WICT,WICT" line.word 0x2 "WMCR,Watchdog Miscellaneous Control Register" bitfld.word 0x2 0. "PDE,PDE" "0: Power Down Counter of WDOG is disabled.,1: Power Down Counter of WDOG is enabled (Default)." tree.end tree "WDOG2" base ad:0x40034000 group.word 0x0++0x3 line.word 0x0 "WCR,Watchdog Control Register" hexmask.word.byte 0x0 8.--15. 1. "WT,WT" bitfld.word 0x0 7. "WDW,WDW" "0: Continue WDOG timer operation (Default).,1: Suspend WDOG timer operation." newline bitfld.word 0x0 6. "SRE,Software Reset Extension an optional way to generate software reset" "0: using original way to generate software reset..,1: using new way to generate software reset." bitfld.word 0x0 5. "WDA,WDA" "0: Assert WDOG_B output.,1: No effect on system (Default)." newline bitfld.word 0x0 4. "SRS,SRS" "0: Assert system reset signal.,1: No effect on the system (Default)." bitfld.word 0x0 3. "WDT,WDT" "0: No effect on WDOG_B (Default).,1: Assert WDOG_B upon a Watchdog Time-out event." newline bitfld.word 0x0 2. "WDE,WDE" "0: Disable the Watchdog (Default).,1: Enable the Watchdog." bitfld.word 0x0 1. "WDBG,WDBG" "0: Continue WDOG timer operation (Default).,1: Suspend the watchdog timer." newline bitfld.word 0x0 0. "WDZST,WDZST" "0: Continue timer operation (Default).,1: Suspend the watchdog timer." line.word 0x2 "WSR,Watchdog Service Register" hexmask.word 0x2 0.--15. 1. "WSR,WSR" rgroup.word 0x4++0x1 line.word 0x0 "WRSR,Watchdog Reset Status Register" bitfld.word 0x0 4. "POR,POR" "0: Reset is not the result of a power on reset.,1: Reset is the result of a power on reset." bitfld.word 0x0 1. "TOUT,TOUT" "0: Reset is not the result of a WDOG timeout.,1: Reset is the result of a WDOG timeout." newline bitfld.word 0x0 0. "SFTW,SFTW" "0: Reset is not the result of a software reset.,1: Reset is the result of a software reset." group.word 0x6++0x3 line.word 0x0 "WICR,Watchdog Interrupt Control Register" bitfld.word 0x0 15. "WIE,WIE" "0: Disable Interrupt (Default).,1: Enable Interrupt." eventfld.word 0x0 14. "WTIS,WTIS" "0: No interrupt has occurred (Default).,1: Interrupt has occurred" newline hexmask.word.byte 0x0 0.--7. 1. "WICT,WICT" line.word 0x2 "WMCR,Watchdog Miscellaneous Control Register" bitfld.word 0x2 0. "PDE,PDE" "0: Power Down Counter of WDOG is disabled.,1: Power Down Counter of WDOG is enabled (Default)." tree.end tree.end tree "XBARA" base ad:0x0 tree "XBARA1" base ad:0x4003C000 group.word 0x0++0xB3 line.word 0x0 "SEL0,Crossbar A Select Register 0" hexmask.word.byte 0x0 8.--15. 1. "SEL1,Input (XBARA_INn) to be muxed to XBARA_OUT1 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x0 0.--7. 1. "SEL0,Input (XBARA_INn) to be muxed to XBARA_OUT0 (refer to Functional Description section for input/output assignment)" line.word 0x2 "SEL1,Crossbar A Select Register 1" hexmask.word.byte 0x2 8.--15. 1. "SEL3,Input (XBARA_INn) to be muxed to XBARA_OUT3 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2 0.--7. 1. "SEL2,Input (XBARA_INn) to be muxed to XBARA_OUT2 (refer to Functional Description section for input/output assignment)" line.word 0x4 "SEL2,Crossbar A Select Register 2" hexmask.word.byte 0x4 8.--15. 1. "SEL5,Input (XBARA_INn) to be muxed to XBARA_OUT5 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4 0.--7. 1. "SEL4,Input (XBARA_INn) to be muxed to XBARA_OUT4 (refer to Functional Description section for input/output assignment)" line.word 0x6 "SEL3,Crossbar A Select Register 3" hexmask.word.byte 0x6 8.--15. 1. "SEL7,Input (XBARA_INn) to be muxed to XBARA_OUT7 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6 0.--7. 1. "SEL6,Input (XBARA_INn) to be muxed to XBARA_OUT6 (refer to Functional Description section for input/output assignment)" line.word 0x8 "SEL4,Crossbar A Select Register 4" hexmask.word.byte 0x8 8.--15. 1. "SEL9,Input (XBARA_INn) to be muxed to XBARA_OUT9 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8 0.--7. 1. "SEL8,Input (XBARA_INn) to be muxed to XBARA_OUT8 (refer to Functional Description section for input/output assignment)" line.word 0xA "SEL5,Crossbar A Select Register 5" hexmask.word.byte 0xA 8.--15. 1. "SEL11,Input (XBARA_INn) to be muxed to XBARA_OUT11 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA 0.--7. 1. "SEL10,Input (XBARA_INn) to be muxed to XBARA_OUT10 (refer to Functional Description section for input/output assignment)" line.word 0xC "SEL6,Crossbar A Select Register 6" hexmask.word.byte 0xC 8.--15. 1. "SEL13,Input (XBARA_INn) to be muxed to XBARA_OUT13 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xC 0.--7. 1. "SEL12,Input (XBARA_INn) to be muxed to XBARA_OUT12 (refer to Functional Description section for input/output assignment)" line.word 0xE "SEL7,Crossbar A Select Register 7" hexmask.word.byte 0xE 8.--15. 1. "SEL15,Input (XBARA_INn) to be muxed to XBARA_OUT15 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xE 0.--7. 1. "SEL14,Input (XBARA_INn) to be muxed to XBARA_OUT14 (refer to Functional Description section for input/output assignment)" line.word 0x10 "SEL8,Crossbar A Select Register 8" hexmask.word.byte 0x10 8.--15. 1. "SEL17,Input (XBARA_INn) to be muxed to XBARA_OUT17 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x10 0.--7. 1. "SEL16,Input (XBARA_INn) to be muxed to XBARA_OUT16 (refer to Functional Description section for input/output assignment)" line.word 0x12 "SEL9,Crossbar A Select Register 9" hexmask.word.byte 0x12 8.--15. 1. "SEL19,Input (XBARA_INn) to be muxed to XBARA_OUT19 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x12 0.--7. 1. "SEL18,Input (XBARA_INn) to be muxed to XBARA_OUT18 (refer to Functional Description section for input/output assignment)" line.word 0x14 "SEL10,Crossbar A Select Register 10" hexmask.word.byte 0x14 8.--15. 1. "SEL21,Input (XBARA_INn) to be muxed to XBARA_OUT21 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x14 0.--7. 1. "SEL20,Input (XBARA_INn) to be muxed to XBARA_OUT20 (refer to Functional Description section for input/output assignment)" line.word 0x16 "SEL11,Crossbar A Select Register 11" hexmask.word.byte 0x16 8.--15. 1. "SEL23,Input (XBARA_INn) to be muxed to XBARA_OUT23 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x16 0.--7. 1. "SEL22,Input (XBARA_INn) to be muxed to XBARA_OUT22 (refer to Functional Description section for input/output assignment)" line.word 0x18 "SEL12,Crossbar A Select Register 12" hexmask.word.byte 0x18 8.--15. 1. "SEL25,Input (XBARA_INn) to be muxed to XBARA_OUT25 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x18 0.--7. 1. "SEL24,Input (XBARA_INn) to be muxed to XBARA_OUT24 (refer to Functional Description section for input/output assignment)" line.word 0x1A "SEL13,Crossbar A Select Register 13" hexmask.word.byte 0x1A 8.--15. 1. "SEL27,Input (XBARA_INn) to be muxed to XBARA_OUT27 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x1A 0.--7. 1. "SEL26,Input (XBARA_INn) to be muxed to XBARA_OUT26 (refer to Functional Description section for input/output assignment)" line.word 0x1C "SEL14,Crossbar A Select Register 14" hexmask.word.byte 0x1C 8.--15. 1. "SEL29,Input (XBARA_INn) to be muxed to XBARA_OUT29 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x1C 0.--7. 1. "SEL28,Input (XBARA_INn) to be muxed to XBARA_OUT28 (refer to Functional Description section for input/output assignment)" line.word 0x1E "SEL15,Crossbar A Select Register 15" hexmask.word.byte 0x1E 8.--15. 1. "SEL31,Input (XBARA_INn) to be muxed to XBARA_OUT31 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x1E 0.--7. 1. "SEL30,Input (XBARA_INn) to be muxed to XBARA_OUT30 (refer to Functional Description section for input/output assignment)" line.word 0x20 "SEL16,Crossbar A Select Register 16" hexmask.word.byte 0x20 8.--15. 1. "SEL33,Input (XBARA_INn) to be muxed to XBARA_OUT33 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x20 0.--7. 1. "SEL32,Input (XBARA_INn) to be muxed to XBARA_OUT32 (refer to Functional Description section for input/output assignment)" line.word 0x22 "SEL17,Crossbar A Select Register 17" hexmask.word.byte 0x22 8.--15. 1. "SEL35,Input (XBARA_INn) to be muxed to XBARA_OUT35 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x22 0.--7. 1. "SEL34,Input (XBARA_INn) to be muxed to XBARA_OUT34 (refer to Functional Description section for input/output assignment)" line.word 0x24 "SEL18,Crossbar A Select Register 18" hexmask.word.byte 0x24 8.--15. 1. "SEL37,Input (XBARA_INn) to be muxed to XBARA_OUT37 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x24 0.--7. 1. "SEL36,Input (XBARA_INn) to be muxed to XBARA_OUT36 (refer to Functional Description section for input/output assignment)" line.word 0x26 "SEL19,Crossbar A Select Register 19" hexmask.word.byte 0x26 8.--15. 1. "SEL39,Input (XBARA_INn) to be muxed to XBARA_OUT39 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x26 0.--7. 1. "SEL38,Input (XBARA_INn) to be muxed to XBARA_OUT38 (refer to Functional Description section for input/output assignment)" line.word 0x28 "SEL20,Crossbar A Select Register 20" hexmask.word.byte 0x28 8.--15. 1. "SEL41,Input (XBARA_INn) to be muxed to XBARA_OUT41 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x28 0.--7. 1. "SEL40,Input (XBARA_INn) to be muxed to XBARA_OUT40 (refer to Functional Description section for input/output assignment)" line.word 0x2A "SEL21,Crossbar A Select Register 21" hexmask.word.byte 0x2A 8.--15. 1. "SEL43,Input (XBARA_INn) to be muxed to XBARA_OUT43 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2A 0.--7. 1. "SEL42,Input (XBARA_INn) to be muxed to XBARA_OUT42 (refer to Functional Description section for input/output assignment)" line.word 0x2C "SEL22,Crossbar A Select Register 22" hexmask.word.byte 0x2C 8.--15. 1. "SEL45,Input (XBARA_INn) to be muxed to XBARA_OUT45 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2C 0.--7. 1. "SEL44,Input (XBARA_INn) to be muxed to XBARA_OUT44 (refer to Functional Description section for input/output assignment)" line.word 0x2E "SEL23,Crossbar A Select Register 23" hexmask.word.byte 0x2E 8.--15. 1. "SEL47,Input (XBARA_INn) to be muxed to XBARA_OUT47 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2E 0.--7. 1. "SEL46,Input (XBARA_INn) to be muxed to XBARA_OUT46 (refer to Functional Description section for input/output assignment)" line.word 0x30 "SEL24,Crossbar A Select Register 24" hexmask.word.byte 0x30 8.--15. 1. "SEL49,Input (XBARA_INn) to be muxed to XBARA_OUT49 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x30 0.--7. 1. "SEL48,Input (XBARA_INn) to be muxed to XBARA_OUT48 (refer to Functional Description section for input/output assignment)" line.word 0x32 "SEL25,Crossbar A Select Register 25" hexmask.word.byte 0x32 8.--15. 1. "SEL51,Input (XBARA_INn) to be muxed to XBARA_OUT51 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x32 0.--7. 1. "SEL50,Input (XBARA_INn) to be muxed to XBARA_OUT50 (refer to Functional Description section for input/output assignment)" line.word 0x34 "SEL26,Crossbar A Select Register 26" hexmask.word.byte 0x34 8.--15. 1. "SEL53,Input (XBARA_INn) to be muxed to XBARA_OUT53 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x34 0.--7. 1. "SEL52,Input (XBARA_INn) to be muxed to XBARA_OUT52 (refer to Functional Description section for input/output assignment)" line.word 0x36 "SEL27,Crossbar A Select Register 27" hexmask.word.byte 0x36 8.--15. 1. "SEL55,Input (XBARA_INn) to be muxed to XBARA_OUT55 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x36 0.--7. 1. "SEL54,Input (XBARA_INn) to be muxed to XBARA_OUT54 (refer to Functional Description section for input/output assignment)" line.word 0x38 "SEL28,Crossbar A Select Register 28" hexmask.word.byte 0x38 8.--15. 1. "SEL57,Input (XBARA_INn) to be muxed to XBARA_OUT57 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x38 0.--7. 1. "SEL56,Input (XBARA_INn) to be muxed to XBARA_OUT56 (refer to Functional Description section for input/output assignment)" line.word 0x3A "SEL29,Crossbar A Select Register 29" hexmask.word.byte 0x3A 8.--15. 1. "SEL59,Input (XBARA_INn) to be muxed to XBARA_OUT59 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x3A 0.--7. 1. "SEL58,Input (XBARA_INn) to be muxed to XBARA_OUT58 (refer to Functional Description section for input/output assignment)" line.word 0x3C "SEL30,Crossbar A Select Register 30" hexmask.word.byte 0x3C 8.--15. 1. "SEL61,Input (XBARA_INn) to be muxed to XBARA_OUT61 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x3C 0.--7. 1. "SEL60,Input (XBARA_INn) to be muxed to XBARA_OUT60 (refer to Functional Description section for input/output assignment)" line.word 0x3E "SEL31,Crossbar A Select Register 31" hexmask.word.byte 0x3E 8.--15. 1. "SEL63,Input (XBARA_INn) to be muxed to XBARA_OUT63 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x3E 0.--7. 1. "SEL62,Input (XBARA_INn) to be muxed to XBARA_OUT62 (refer to Functional Description section for input/output assignment)" line.word 0x40 "SEL32,Crossbar A Select Register 32" hexmask.word.byte 0x40 8.--15. 1. "SEL65,Input (XBARA_INn) to be muxed to XBARA_OUT65 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x40 0.--7. 1. "SEL64,Input (XBARA_INn) to be muxed to XBARA_OUT64 (refer to Functional Description section for input/output assignment)" line.word 0x42 "SEL33,Crossbar A Select Register 33" hexmask.word.byte 0x42 8.--15. 1. "SEL67,Input (XBARA_INn) to be muxed to XBARA_OUT67 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x42 0.--7. 1. "SEL66,Input (XBARA_INn) to be muxed to XBARA_OUT66 (refer to Functional Description section for input/output assignment)" line.word 0x44 "SEL34,Crossbar A Select Register 34" hexmask.word.byte 0x44 8.--15. 1. "SEL69,Input (XBARA_INn) to be muxed to XBARA_OUT69 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x44 0.--7. 1. "SEL68,Input (XBARA_INn) to be muxed to XBARA_OUT68 (refer to Functional Description section for input/output assignment)" line.word 0x46 "SEL35,Crossbar A Select Register 35" hexmask.word.byte 0x46 8.--15. 1. "SEL71,Input (XBARA_INn) to be muxed to XBARA_OUT71 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x46 0.--7. 1. "SEL70,Input (XBARA_INn) to be muxed to XBARA_OUT70 (refer to Functional Description section for input/output assignment)" line.word 0x48 "SEL36,Crossbar A Select Register 36" hexmask.word.byte 0x48 8.--15. 1. "SEL73,Input (XBARA_INn) to be muxed to XBARA_OUT73 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x48 0.--7. 1. "SEL72,Input (XBARA_INn) to be muxed to XBARA_OUT72 (refer to Functional Description section for input/output assignment)" line.word 0x4A "SEL37,Crossbar A Select Register 37" hexmask.word.byte 0x4A 8.--15. 1. "SEL75,Input (XBARA_INn) to be muxed to XBARA_OUT75 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4A 0.--7. 1. "SEL74,Input (XBARA_INn) to be muxed to XBARA_OUT74 (refer to Functional Description section for input/output assignment)" line.word 0x4C "SEL38,Crossbar A Select Register 38" hexmask.word.byte 0x4C 8.--15. 1. "SEL77,Input (XBARA_INn) to be muxed to XBARA_OUT77 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4C 0.--7. 1. "SEL76,Input (XBARA_INn) to be muxed to XBARA_OUT76 (refer to Functional Description section for input/output assignment)" line.word 0x4E "SEL39,Crossbar A Select Register 39" hexmask.word.byte 0x4E 8.--15. 1. "SEL79,Input (XBARA_INn) to be muxed to XBARA_OUT79 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4E 0.--7. 1. "SEL78,Input (XBARA_INn) to be muxed to XBARA_OUT78 (refer to Functional Description section for input/output assignment)" line.word 0x50 "SEL40,Crossbar A Select Register 40" hexmask.word.byte 0x50 8.--15. 1. "SEL81,Input (XBARA_INn) to be muxed to XBARA_OUT81 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x50 0.--7. 1. "SEL80,Input (XBARA_INn) to be muxed to XBARA_OUT80 (refer to Functional Description section for input/output assignment)" line.word 0x52 "SEL41,Crossbar A Select Register 41" hexmask.word.byte 0x52 8.--15. 1. "SEL83,Input (XBARA_INn) to be muxed to XBARA_OUT83 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x52 0.--7. 1. "SEL82,Input (XBARA_INn) to be muxed to XBARA_OUT82 (refer to Functional Description section for input/output assignment)" line.word 0x54 "SEL42,Crossbar A Select Register 42" hexmask.word.byte 0x54 8.--15. 1. "SEL85,Input (XBARA_INn) to be muxed to XBARA_OUT85 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x54 0.--7. 1. "SEL84,Input (XBARA_INn) to be muxed to XBARA_OUT84 (refer to Functional Description section for input/output assignment)" line.word 0x56 "SEL43,Crossbar A Select Register 43" hexmask.word.byte 0x56 8.--15. 1. "SEL87,Input (XBARA_INn) to be muxed to XBARA_OUT87 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x56 0.--7. 1. "SEL86,Input (XBARA_INn) to be muxed to XBARA_OUT86 (refer to Functional Description section for input/output assignment)" line.word 0x58 "SEL44,Crossbar A Select Register 44" hexmask.word.byte 0x58 8.--15. 1. "SEL89,Input (XBARA_INn) to be muxed to XBARA_OUT89 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x58 0.--7. 1. "SEL88,Input (XBARA_INn) to be muxed to XBARA_OUT88 (refer to Functional Description section for input/output assignment)" line.word 0x5A "SEL45,Crossbar A Select Register 45" hexmask.word.byte 0x5A 8.--15. 1. "SEL91,Input (XBARA_INn) to be muxed to XBARA_OUT91 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x5A 0.--7. 1. "SEL90,Input (XBARA_INn) to be muxed to XBARA_OUT90 (refer to Functional Description section for input/output assignment)" line.word 0x5C "SEL46,Crossbar A Select Register 46" hexmask.word.byte 0x5C 8.--15. 1. "SEL93,Input (XBARA_INn) to be muxed to XBARA_OUT93 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x5C 0.--7. 1. "SEL92,Input (XBARA_INn) to be muxed to XBARA_OUT92 (refer to Functional Description section for input/output assignment)" line.word 0x5E "SEL47,Crossbar A Select Register 47" hexmask.word.byte 0x5E 8.--15. 1. "SEL95,Input (XBARA_INn) to be muxed to XBARA_OUT95 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x5E 0.--7. 1. "SEL94,Input (XBARA_INn) to be muxed to XBARA_OUT94 (refer to Functional Description section for input/output assignment)" line.word 0x60 "SEL48,Crossbar A Select Register 48" hexmask.word.byte 0x60 8.--15. 1. "SEL97,Input (XBARA_INn) to be muxed to XBARA_OUT97 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x60 0.--7. 1. "SEL96,Input (XBARA_INn) to be muxed to XBARA_OUT96 (refer to Functional Description section for input/output assignment)" line.word 0x62 "SEL49,Crossbar A Select Register 49" hexmask.word.byte 0x62 8.--15. 1. "SEL99,Input (XBARA_INn) to be muxed to XBARA_OUT99 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x62 0.--7. 1. "SEL98,Input (XBARA_INn) to be muxed to XBARA_OUT98 (refer to Functional Description section for input/output assignment)" line.word 0x64 "SEL50,Crossbar A Select Register 50" hexmask.word.byte 0x64 8.--15. 1. "SEL101,Input (XBARA_INn) to be muxed to XBARA_OUT101 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x64 0.--7. 1. "SEL100,Input (XBARA_INn) to be muxed to XBARA_OUT100 (refer to Functional Description section for input/output assignment)" line.word 0x66 "SEL51,Crossbar A Select Register 51" hexmask.word.byte 0x66 8.--15. 1. "SEL103,Input (XBARA_INn) to be muxed to XBARA_OUT103 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x66 0.--7. 1. "SEL102,Input (XBARA_INn) to be muxed to XBARA_OUT102 (refer to Functional Description section for input/output assignment)" line.word 0x68 "SEL52,Crossbar A Select Register 52" hexmask.word.byte 0x68 8.--15. 1. "SEL105,Input (XBARA_INn) to be muxed to XBARA_OUT105 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x68 0.--7. 1. "SEL104,Input (XBARA_INn) to be muxed to XBARA_OUT104 (refer to Functional Description section for input/output assignment)" line.word 0x6A "SEL53,Crossbar A Select Register 53" hexmask.word.byte 0x6A 8.--15. 1. "SEL107,Input (XBARA_INn) to be muxed to XBARA_OUT107 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6A 0.--7. 1. "SEL106,Input (XBARA_INn) to be muxed to XBARA_OUT106 (refer to Functional Description section for input/output assignment)" line.word 0x6C "SEL54,Crossbar A Select Register 54" hexmask.word.byte 0x6C 8.--15. 1. "SEL109,Input (XBARA_INn) to be muxed to XBARA_OUT109 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6C 0.--7. 1. "SEL108,Input (XBARA_INn) to be muxed to XBARA_OUT108 (refer to Functional Description section for input/output assignment)" line.word 0x6E "SEL55,Crossbar A Select Register 55" hexmask.word.byte 0x6E 8.--15. 1. "SEL111,Input (XBARA_INn) to be muxed to XBARA_OUT111 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6E 0.--7. 1. "SEL110,Input (XBARA_INn) to be muxed to XBARA_OUT110 (refer to Functional Description section for input/output assignment)" line.word 0x70 "SEL56,Crossbar A Select Register 56" hexmask.word.byte 0x70 8.--15. 1. "SEL113,Input (XBARA_INn) to be muxed to XBARA_OUT113 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x70 0.--7. 1. "SEL112,Input (XBARA_INn) to be muxed to XBARA_OUT112 (refer to Functional Description section for input/output assignment)" line.word 0x72 "SEL57,Crossbar A Select Register 57" hexmask.word.byte 0x72 8.--15. 1. "SEL115,Input (XBARA_INn) to be muxed to XBARA_OUT115 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x72 0.--7. 1. "SEL114,Input (XBARA_INn) to be muxed to XBARA_OUT114 (refer to Functional Description section for input/output assignment)" line.word 0x74 "SEL58,Crossbar A Select Register 58" hexmask.word.byte 0x74 8.--15. 1. "SEL117,Input (XBARA_INn) to be muxed to XBARA_OUT117 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x74 0.--7. 1. "SEL116,Input (XBARA_INn) to be muxed to XBARA_OUT116 (refer to Functional Description section for input/output assignment)" line.word 0x76 "SEL59,Crossbar A Select Register 59" hexmask.word.byte 0x76 8.--15. 1. "SEL119,Input (XBARA_INn) to be muxed to XBARA_OUT119 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x76 0.--7. 1. "SEL118,Input (XBARA_INn) to be muxed to XBARA_OUT118 (refer to Functional Description section for input/output assignment)" line.word 0x78 "SEL60,Crossbar A Select Register 60" hexmask.word.byte 0x78 8.--15. 1. "SEL121,Input (XBARA_INn) to be muxed to XBARA_OUT121 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x78 0.--7. 1. "SEL120,Input (XBARA_INn) to be muxed to XBARA_OUT120 (refer to Functional Description section for input/output assignment)" line.word 0x7A "SEL61,Crossbar A Select Register 61" hexmask.word.byte 0x7A 8.--15. 1. "SEL123,Input (XBARA_INn) to be muxed to XBARA_OUT123 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x7A 0.--7. 1. "SEL122,Input (XBARA_INn) to be muxed to XBARA_OUT122 (refer to Functional Description section for input/output assignment)" line.word 0x7C "SEL62,Crossbar A Select Register 62" hexmask.word.byte 0x7C 8.--15. 1. "SEL125,Input (XBARA_INn) to be muxed to XBARA_OUT125 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x7C 0.--7. 1. "SEL124,Input (XBARA_INn) to be muxed to XBARA_OUT124 (refer to Functional Description section for input/output assignment)" line.word 0x7E "SEL63,Crossbar A Select Register 63" hexmask.word.byte 0x7E 8.--15. 1. "SEL127,Input (XBARA_INn) to be muxed to XBARA_OUT127 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x7E 0.--7. 1. "SEL126,Input (XBARA_INn) to be muxed to XBARA_OUT126 (refer to Functional Description section for input/output assignment)" line.word 0x80 "SEL64,Crossbar A Select Register 64" hexmask.word.byte 0x80 8.--15. 1. "SEL129,Input (XBARA_INn) to be muxed to XBARA_OUT129 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x80 0.--7. 1. "SEL128,Input (XBARA_INn) to be muxed to XBARA_OUT128 (refer to Functional Description section for input/output assignment)" line.word 0x82 "SEL65,Crossbar A Select Register 65" hexmask.word.byte 0x82 8.--15. 1. "SEL131,Input (XBARA_INn) to be muxed to XBARA_OUT131 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x82 0.--7. 1. "SEL130,Input (XBARA_INn) to be muxed to XBARA_OUT130 (refer to Functional Description section for input/output assignment)" line.word 0x84 "SEL66,Crossbar A Select Register 66" hexmask.word.byte 0x84 8.--15. 1. "SEL133,Input (XBARA_INn) to be muxed to XBARA_OUT133 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x84 0.--7. 1. "SEL132,Input (XBARA_INn) to be muxed to XBARA_OUT132 (refer to Functional Description section for input/output assignment)" line.word 0x86 "SEL67,Crossbar A Select Register 67" hexmask.word.byte 0x86 8.--15. 1. "SEL135,Input (XBARA_INn) to be muxed to XBARA_OUT135 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x86 0.--7. 1. "SEL134,Input (XBARA_INn) to be muxed to XBARA_OUT134 (refer to Functional Description section for input/output assignment)" line.word 0x88 "SEL68,Crossbar A Select Register 68" hexmask.word.byte 0x88 8.--15. 1. "SEL137,Input (XBARA_INn) to be muxed to XBARA_OUT137 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x88 0.--7. 1. "SEL136,Input (XBARA_INn) to be muxed to XBARA_OUT136 (refer to Functional Description section for input/output assignment)" line.word 0x8A "SEL69,Crossbar A Select Register 69" hexmask.word.byte 0x8A 8.--15. 1. "SEL139,Input (XBARA_INn) to be muxed to XBARA_OUT139 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8A 0.--7. 1. "SEL138,Input (XBARA_INn) to be muxed to XBARA_OUT138 (refer to Functional Description section for input/output assignment)" line.word 0x8C "SEL70,Crossbar A Select Register 70" hexmask.word.byte 0x8C 8.--15. 1. "SEL141,Input (XBARA_INn) to be muxed to XBARA_OUT141 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8C 0.--7. 1. "SEL140,Input (XBARA_INn) to be muxed to XBARA_OUT140 (refer to Functional Description section for input/output assignment)" line.word 0x8E "SEL71,Crossbar A Select Register 71" hexmask.word.byte 0x8E 8.--15. 1. "SEL143,Input (XBARA_INn) to be muxed to XBARA_OUT143 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8E 0.--7. 1. "SEL142,Input (XBARA_INn) to be muxed to XBARA_OUT142 (refer to Functional Description section for input/output assignment)" line.word 0x90 "SEL72,Crossbar A Select Register 72" hexmask.word.byte 0x90 8.--15. 1. "SEL145,Input (XBARA_INn) to be muxed to XBARA_OUT145 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x90 0.--7. 1. "SEL144,Input (XBARA_INn) to be muxed to XBARA_OUT144 (refer to Functional Description section for input/output assignment)" line.word 0x92 "SEL73,Crossbar A Select Register 73" hexmask.word.byte 0x92 8.--15. 1. "SEL147,Input (XBARA_INn) to be muxed to XBARA_OUT147 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x92 0.--7. 1. "SEL146,Input (XBARA_INn) to be muxed to XBARA_OUT146 (refer to Functional Description section for input/output assignment)" line.word 0x94 "SEL74,Crossbar A Select Register 74" hexmask.word.byte 0x94 8.--15. 1. "SEL149,Input (XBARA_INn) to be muxed to XBARA_OUT149 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x94 0.--7. 1. "SEL148,Input (XBARA_INn) to be muxed to XBARA_OUT148 (refer to Functional Description section for input/output assignment)" line.word 0x96 "SEL75,Crossbar A Select Register 75" hexmask.word.byte 0x96 8.--15. 1. "SEL151,Input (XBARA_INn) to be muxed to XBARA_OUT151 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x96 0.--7. 1. "SEL150,Input (XBARA_INn) to be muxed to XBARA_OUT150 (refer to Functional Description section for input/output assignment)" line.word 0x98 "SEL76,Crossbar A Select Register 76" hexmask.word.byte 0x98 8.--15. 1. "SEL153,Input (XBARA_INn) to be muxed to XBARA_OUT153 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x98 0.--7. 1. "SEL152,Input (XBARA_INn) to be muxed to XBARA_OUT152 (refer to Functional Description section for input/output assignment)" line.word 0x9A "SEL77,Crossbar A Select Register 77" hexmask.word.byte 0x9A 8.--15. 1. "SEL155,Input (XBARA_INn) to be muxed to XBARA_OUT155 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x9A 0.--7. 1. "SEL154,Input (XBARA_INn) to be muxed to XBARA_OUT154 (refer to Functional Description section for input/output assignment)" line.word 0x9C "SEL78,Crossbar A Select Register 78" hexmask.word.byte 0x9C 8.--15. 1. "SEL157,Input (XBARA_INn) to be muxed to XBARA_OUT157 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x9C 0.--7. 1. "SEL156,Input (XBARA_INn) to be muxed to XBARA_OUT156 (refer to Functional Description section for input/output assignment)" line.word 0x9E "SEL79,Crossbar A Select Register 79" hexmask.word.byte 0x9E 8.--15. 1. "SEL159,Input (XBARA_INn) to be muxed to XBARA_OUT159 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x9E 0.--7. 1. "SEL158,Input (XBARA_INn) to be muxed to XBARA_OUT158 (refer to Functional Description section for input/output assignment)" line.word 0xA0 "SEL80,Crossbar A Select Register 80" hexmask.word.byte 0xA0 8.--15. 1. "SEL161,Input (XBARA_INn) to be muxed to XBARA_OUT161 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA0 0.--7. 1. "SEL160,Input (XBARA_INn) to be muxed to XBARA_OUT160 (refer to Functional Description section for input/output assignment)" line.word 0xA2 "SEL81,Crossbar A Select Register 81" hexmask.word.byte 0xA2 8.--15. 1. "SEL163,Input (XBARA_INn) to be muxed to XBARA_OUT163 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA2 0.--7. 1. "SEL162,Input (XBARA_INn) to be muxed to XBARA_OUT162 (refer to Functional Description section for input/output assignment)" line.word 0xA4 "SEL82,Crossbar A Select Register 82" hexmask.word.byte 0xA4 8.--15. 1. "SEL165,Input (XBARA_INn) to be muxed to XBARA_OUT165 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA4 0.--7. 1. "SEL164,Input (XBARA_INn) to be muxed to XBARA_OUT164 (refer to Functional Description section for input/output assignment)" line.word 0xA6 "SEL83,Crossbar A Select Register 83" hexmask.word.byte 0xA6 8.--15. 1. "SEL167,Input (XBARA_INn) to be muxed to XBARA_OUT167 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA6 0.--7. 1. "SEL166,Input (XBARA_INn) to be muxed to XBARA_OUT166 (refer to Functional Description section for input/output assignment)" line.word 0xA8 "SEL84,Crossbar A Select Register 84" hexmask.word.byte 0xA8 8.--15. 1. "SEL169,Input (XBARA_INn) to be muxed to XBARA_OUT169 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA8 0.--7. 1. "SEL168,Input (XBARA_INn) to be muxed to XBARA_OUT168 (refer to Functional Description section for input/output assignment)" line.word 0xAA "SEL85,Crossbar A Select Register 85" hexmask.word.byte 0xAA 8.--15. 1. "SEL171,Input (XBARA_INn) to be muxed to XBARA_OUT171 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xAA 0.--7. 1. "SEL170,Input (XBARA_INn) to be muxed to XBARA_OUT170 (refer to Functional Description section for input/output assignment)" line.word 0xAC "SEL86,Crossbar A Select Register 86" hexmask.word.byte 0xAC 8.--15. 1. "SEL173,Input (XBARA_INn) to be muxed to XBARA_OUT173 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xAC 0.--7. 1. "SEL172,Input (XBARA_INn) to be muxed to XBARA_OUT172 (refer to Functional Description section for input/output assignment)" line.word 0xAE "SEL87,Crossbar A Select Register 87" hexmask.word.byte 0xAE 8.--15. 1. "SEL175,Input (XBARA_INn) to be muxed to XBARA_OUT175 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xAE 0.--7. 1. "SEL174,Input (XBARA_INn) to be muxed to XBARA_OUT174 (refer to Functional Description section for input/output assignment)" line.word 0xB0 "CTRL0,Crossbar A Control Register 0" eventfld.word 0xB0 12. "STS1,Edge detection status for XBAR_OUT1" "0: Active edge not yet detected on XBAR_OUT1,1: Active edge detected on XBAR_OUT1" bitfld.word 0xB0 10.--11. "EDGE1,Active edge for edge detection on XBAR_OUT1" "0: STS1 never asserts,1: STS1 asserts on rising edges of XBAR_OUT1,2: STS1 asserts on falling edges of XBAR_OUT1,3: STS1 asserts on rising and falling edges of.." newline bitfld.word 0xB0 9. "IEN1,Interrupt Enable for XBAR_OUT1" "0: Interrupt disabled,1: Interrupt enabled" bitfld.word 0xB0 8. "DEN1,DMA Enable for XBAR_OUT1" "0: DMA disabled,1: DMA enabled" newline eventfld.word 0xB0 4. "STS0,Edge detection status for XBAR_OUT0" "0: Active edge not yet detected on XBAR_OUT0,1: Active edge detected on XBAR_OUT0" bitfld.word 0xB0 2.--3. "EDGE0,Active edge for edge detection on XBAR_OUT0" "0: STS0 never asserts,1: STS0 asserts on rising edges of XBAR_OUT0,2: STS0 asserts on falling edges of XBAR_OUT0,3: STS0 asserts on rising and falling edges of.." newline bitfld.word 0xB0 1. "IEN0,Interrupt Enable for XBAR_OUT0" "0: Interrupt disabled,1: Interrupt enabled" bitfld.word 0xB0 0. "DEN0,DMA Enable for XBAR_OUT0" "0: DMA disabled,1: DMA enabled" line.word 0xB2 "CTRL1,Crossbar A Control Register 1" eventfld.word 0xB2 12. "STS3,Edge detection status for XBAR_OUT3" "0: Active edge not yet detected on XBAR_OUT3,1: Active edge detected on XBAR_OUT3" bitfld.word 0xB2 10.--11. "EDGE3,Active edge for edge detection on XBAR_OUT3" "0: STS3 never asserts,1: STS3 asserts on rising edges of XBAR_OUT3,2: STS3 asserts on falling edges of XBAR_OUT3,3: STS3 asserts on rising and falling edges of.." newline bitfld.word 0xB2 9. "IEN3,Interrupt Enable for XBAR_OUT3" "0: Interrupt disabled,1: Interrupt enabled" bitfld.word 0xB2 8. "DEN3,DMA Enable for XBAR_OUT3" "0: DMA disabled,1: DMA enabled" newline eventfld.word 0xB2 4. "STS2,Edge detection status for XBAR_OUT2" "0: Active edge not yet detected on XBAR_OUT2,1: Active edge detected on XBAR_OUT2" bitfld.word 0xB2 2.--3. "EDGE2,Active edge for edge detection on XBAR_OUT2" "0: STS2 never asserts,1: STS2 asserts on rising edges of XBAR_OUT2,2: STS2 asserts on falling edges of XBAR_OUT2,3: STS2 asserts on rising and falling edges of.." newline bitfld.word 0xB2 1. "IEN2,Interrupt Enable for XBAR_OUT2" "0: Interrupt disabled,1: Interrupt enabled" bitfld.word 0xB2 0. "DEN2,DMA Enable for XBAR_OUT2" "0: DMA disabled,1: DMA enabled" tree.end tree "XBARB2 (Crossbar Switch)" base ad:0x40040000 group.word 0x0++0xF line.word 0x0 "SEL0,Crossbar B Select Register 0" hexmask.word.byte 0x0 8.--14. 1. "SEL1,Input (XBARB_INn) to be muxed to XBARB_OUT1 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x0 0.--6. 1. "SEL0,Input (XBARB_INn) to be muxed to XBARB_OUT0 (refer to Functional Description section for input/output assignment)" line.word 0x2 "SEL1,Crossbar B Select Register 1" hexmask.word.byte 0x2 8.--14. 1. "SEL3,Input (XBARB_INn) to be muxed to XBARB_OUT3 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2 0.--6. 1. "SEL2,Input (XBARB_INn) to be muxed to XBARB_OUT2 (refer to Functional Description section for input/output assignment)" line.word 0x4 "SEL2,Crossbar B Select Register 2" hexmask.word.byte 0x4 8.--14. 1. "SEL5,Input (XBARB_INn) to be muxed to XBARB_OUT5 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4 0.--6. 1. "SEL4,Input (XBARB_INn) to be muxed to XBARB_OUT4 (refer to Functional Description section for input/output assignment)" line.word 0x6 "SEL3,Crossbar B Select Register 3" hexmask.word.byte 0x6 8.--14. 1. "SEL7,Input (XBARB_INn) to be muxed to XBARB_OUT7 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6 0.--6. 1. "SEL6,Input (XBARB_INn) to be muxed to XBARB_OUT6 (refer to Functional Description section for input/output assignment)" line.word 0x8 "SEL4,Crossbar B Select Register 4" hexmask.word.byte 0x8 8.--14. 1. "SEL9,Input (XBARB_INn) to be muxed to XBARB_OUT9 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8 0.--6. 1. "SEL8,Input (XBARB_INn) to be muxed to XBARB_OUT8 (refer to Functional Description section for input/output assignment)" line.word 0xA "SEL5,Crossbar B Select Register 5" hexmask.word.byte 0xA 8.--14. 1. "SEL11,Input (XBARB_INn) to be muxed to XBARB_OUT11 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA 0.--6. 1. "SEL10,Input (XBARB_INn) to be muxed to XBARB_OUT10 (refer to Functional Description section for input/output assignment)" line.word 0xC "SEL6,Crossbar B Select Register 6" hexmask.word.byte 0xC 8.--14. 1. "SEL13,Input (XBARB_INn) to be muxed to XBARB_OUT13 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xC 0.--6. 1. "SEL12,Input (XBARB_INn) to be muxed to XBARB_OUT12 (refer to Functional Description section for input/output assignment)" line.word 0xE "SEL7,Crossbar B Select Register 7" hexmask.word.byte 0xE 8.--14. 1. "SEL15,Input (XBARB_INn) to be muxed to XBARB_OUT15 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xE 0.--6. 1. "SEL14,Input (XBARB_INn) to be muxed to XBARB_OUT14 (refer to Functional Description section for input/output assignment)" tree.end tree "XBARB3 (Crossbar Switch)" base ad:0x40044000 group.word 0x0++0xF line.word 0x0 "SEL0,Crossbar B Select Register 0" hexmask.word.byte 0x0 8.--14. 1. "SEL1,Input (XBARB_INn) to be muxed to XBARB_OUT1 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x0 0.--6. 1. "SEL0,Input (XBARB_INn) to be muxed to XBARB_OUT0 (refer to Functional Description section for input/output assignment)" line.word 0x2 "SEL1,Crossbar B Select Register 1" hexmask.word.byte 0x2 8.--14. 1. "SEL3,Input (XBARB_INn) to be muxed to XBARB_OUT3 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x2 0.--6. 1. "SEL2,Input (XBARB_INn) to be muxed to XBARB_OUT2 (refer to Functional Description section for input/output assignment)" line.word 0x4 "SEL2,Crossbar B Select Register 2" hexmask.word.byte 0x4 8.--14. 1. "SEL5,Input (XBARB_INn) to be muxed to XBARB_OUT5 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x4 0.--6. 1. "SEL4,Input (XBARB_INn) to be muxed to XBARB_OUT4 (refer to Functional Description section for input/output assignment)" line.word 0x6 "SEL3,Crossbar B Select Register 3" hexmask.word.byte 0x6 8.--14. 1. "SEL7,Input (XBARB_INn) to be muxed to XBARB_OUT7 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x6 0.--6. 1. "SEL6,Input (XBARB_INn) to be muxed to XBARB_OUT6 (refer to Functional Description section for input/output assignment)" line.word 0x8 "SEL4,Crossbar B Select Register 4" hexmask.word.byte 0x8 8.--14. 1. "SEL9,Input (XBARB_INn) to be muxed to XBARB_OUT9 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0x8 0.--6. 1. "SEL8,Input (XBARB_INn) to be muxed to XBARB_OUT8 (refer to Functional Description section for input/output assignment)" line.word 0xA "SEL5,Crossbar B Select Register 5" hexmask.word.byte 0xA 8.--14. 1. "SEL11,Input (XBARB_INn) to be muxed to XBARB_OUT11 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xA 0.--6. 1. "SEL10,Input (XBARB_INn) to be muxed to XBARB_OUT10 (refer to Functional Description section for input/output assignment)" line.word 0xC "SEL6,Crossbar B Select Register 6" hexmask.word.byte 0xC 8.--14. 1. "SEL13,Input (XBARB_INn) to be muxed to XBARB_OUT13 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xC 0.--6. 1. "SEL12,Input (XBARB_INn) to be muxed to XBARB_OUT12 (refer to Functional Description section for input/output assignment)" line.word 0xE "SEL7,Crossbar B Select Register 7" hexmask.word.byte 0xE 8.--14. 1. "SEL15,Input (XBARB_INn) to be muxed to XBARB_OUT15 (refer to Functional Description section for input/output assignment)" hexmask.word.byte 0xE 0.--6. 1. "SEL14,Input (XBARB_INn) to be muxed to XBARB_OUT14 (refer to Functional Description section for input/output assignment)" tree.end tree.end tree "XECC" base ad:0x0 tree "XECC_FLEXSPI1" base ad:0x4001C000 group.long 0x0++0x17 line.long 0x0 "ECC_CTRL,ECC Control Register" bitfld.long 0x0 3. "SWAP_EN,Swap Data Enable" "0: Disable,1: Enable" bitfld.long 0x0 2. "RECC_EN,Read ECC Function Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 1. "WECC_EN,Write ECC Encode Function Enable" "0: Disable,1: Enable" bitfld.long 0x0 0. "ECC_EN,ECC Function Enable" "0: Disable,1: Enable" line.long 0x4 "ERR_STATUS,Error Interrupt Status Register" hexmask.long 0x4 2.--31. 1. "Reserved1,Reserved" eventfld.long 0x4 1. "MULTI_ERR,Multiple Bits Error" "0: Multiple bits error does not happen.,1: Multiple bits error happens." newline eventfld.long 0x4 0. "SINGLE_ERR,Single Bit Error" "0: Single bit error does not happen.,1: Single bit error happens." line.long 0x8 "ERR_STAT_EN,Error Interrupt Status Enable Register" hexmask.long 0x8 2.--31. 1. "Reserved1,Reserved" bitfld.long 0x8 1. "MULIT_ERR_STAT_EN,Multiple Bits Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x8 0. "SINGLE_ERR_STAT_EN,Single Bit Error Status Enable" "0: Masked,1: Enabled" line.long 0xC "ERR_SIG_EN,Error Interrupt Enable Register" hexmask.long 0xC 2.--31. 1. "Reserved1,Reserved" bitfld.long 0xC 1. "MULTI_ERR_SIG_EN,Multiple Bits Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 0. "SINGLE_ERR_SIG_EN,Single Bit Error Interrupt Enable" "0: Masked,1: Enabled" line.long 0x10 "ERR_DATA_INJ,Error Injection On Write Data" hexmask.long 0x10 0.--31. 1. "ERR_DATA_INJ,Error Injection On Write Data" line.long 0x14 "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" hexmask.long 0x14 0.--31. 1. "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" rgroup.long 0x18++0x23 line.long 0x0 "SINGLE_ERR_ADDR,Single Error Address" hexmask.long 0x0 0.--31. 1. "SINGLE_ERR_ADDR,Single Error Address" line.long 0x4 "SINGLE_ERR_DATA,Single Error Read Data" hexmask.long 0x4 0.--31. 1. "SINGLE_ERR_DATA,Single Error Read Data" line.long 0x8 "SINGLE_ERR_ECC,Single Error ECC Code" hexmask.long 0x8 0.--31. 1. "SINGLE_ERR_ECC,Single Error ECC code" line.long 0xC "SINGLE_ERR_POS,Single Error Bit Position" hexmask.long 0xC 0.--31. 1. "SINGLE_ERR_POS,Single Error bit Position" line.long 0x10 "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" hexmask.long.tbyte 0x10 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x10 0.--7. 1. "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" line.long 0x14 "MULTI_ERR_ADDR,Multiple Error Address" hexmask.long 0x14 0.--31. 1. "MULTI_ERR_ADDR,Multiple Error Address" line.long 0x18 "MULTI_ERR_DATA,Multiple Error Read Data" hexmask.long 0x18 0.--31. 1. "MULTI_ERR_DATA,Multiple Error Read Data" line.long 0x1C "MULTI_ERR_ECC,Multiple Error ECC code" hexmask.long 0x1C 0.--31. 1. "MULTI_ERR_ECC,Multiple Error ECC code" line.long 0x20 "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" hexmask.long.tbyte 0x20 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x20 0.--7. 1. "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" group.long 0x3C++0x1F line.long 0x0 "ECC_BASE_ADDR0,ECC Region 0 Base Address" hexmask.long 0x0 0.--31. 1. "ECC_BASE_ADDR0,ECC Region 0 Base Address" line.long 0x4 "ECC_END_ADDR0,ECC Region 0 End Address" hexmask.long 0x4 0.--31. 1. "ECC_END_ADDR0,ECC Region 0 End Address" line.long 0x8 "ECC_BASE_ADDR1,ECC Region 1 Base Address" hexmask.long 0x8 0.--31. 1. "ECC_BASE_ADDR1,ECC Region 1 Base Address" line.long 0xC "ECC_END_ADDR1,ECC Region 1 End Address" hexmask.long 0xC 0.--31. 1. "ECC_END_ADDR1,ECC Region 1 End Address" line.long 0x10 "ECC_BASE_ADDR2,ECC Region 2 Base Address" hexmask.long 0x10 0.--31. 1. "ECC_BASE_ADDR2,ECC Region 2 Base Address" line.long 0x14 "ECC_END_ADDR2,ECC Region 2 End Address" hexmask.long 0x14 0.--31. 1. "ECC_END_ADDR2,ECC Region 2 End Address" line.long 0x18 "ECC_BASE_ADDR3,ECC Region 3 Base Address" hexmask.long 0x18 0.--31. 1. "ECC_BASE_ADDR3,ECC Region 3 Base Address" line.long 0x1C "ECC_END_ADDR3,ECC Region 3 End Address" hexmask.long 0x1C 0.--31. 1. "ECC_END_ADDR3,ECC Region 3 End Address" tree.end tree "XECC_FLEXSPI2" base ad:0x40020000 group.long 0x0++0x17 line.long 0x0 "ECC_CTRL,ECC Control Register" bitfld.long 0x0 3. "SWAP_EN,Swap Data Enable" "0: Disable,1: Enable" bitfld.long 0x0 2. "RECC_EN,Read ECC Function Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 1. "WECC_EN,Write ECC Encode Function Enable" "0: Disable,1: Enable" bitfld.long 0x0 0. "ECC_EN,ECC Function Enable" "0: Disable,1: Enable" line.long 0x4 "ERR_STATUS,Error Interrupt Status Register" hexmask.long 0x4 2.--31. 1. "Reserved1,Reserved" eventfld.long 0x4 1. "MULTI_ERR,Multiple Bits Error" "0: Multiple bits error does not happen.,1: Multiple bits error happens." newline eventfld.long 0x4 0. "SINGLE_ERR,Single Bit Error" "0: Single bit error does not happen.,1: Single bit error happens." line.long 0x8 "ERR_STAT_EN,Error Interrupt Status Enable Register" hexmask.long 0x8 2.--31. 1. "Reserved1,Reserved" bitfld.long 0x8 1. "MULIT_ERR_STAT_EN,Multiple Bits Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x8 0. "SINGLE_ERR_STAT_EN,Single Bit Error Status Enable" "0: Masked,1: Enabled" line.long 0xC "ERR_SIG_EN,Error Interrupt Enable Register" hexmask.long 0xC 2.--31. 1. "Reserved1,Reserved" bitfld.long 0xC 1. "MULTI_ERR_SIG_EN,Multiple Bits Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 0. "SINGLE_ERR_SIG_EN,Single Bit Error Interrupt Enable" "0: Masked,1: Enabled" line.long 0x10 "ERR_DATA_INJ,Error Injection On Write Data" hexmask.long 0x10 0.--31. 1. "ERR_DATA_INJ,Error Injection On Write Data" line.long 0x14 "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" hexmask.long 0x14 0.--31. 1. "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" rgroup.long 0x18++0x23 line.long 0x0 "SINGLE_ERR_ADDR,Single Error Address" hexmask.long 0x0 0.--31. 1. "SINGLE_ERR_ADDR,Single Error Address" line.long 0x4 "SINGLE_ERR_DATA,Single Error Read Data" hexmask.long 0x4 0.--31. 1. "SINGLE_ERR_DATA,Single Error Read Data" line.long 0x8 "SINGLE_ERR_ECC,Single Error ECC Code" hexmask.long 0x8 0.--31. 1. "SINGLE_ERR_ECC,Single Error ECC code" line.long 0xC "SINGLE_ERR_POS,Single Error Bit Position" hexmask.long 0xC 0.--31. 1. "SINGLE_ERR_POS,Single Error bit Position" line.long 0x10 "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" hexmask.long.tbyte 0x10 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x10 0.--7. 1. "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" line.long 0x14 "MULTI_ERR_ADDR,Multiple Error Address" hexmask.long 0x14 0.--31. 1. "MULTI_ERR_ADDR,Multiple Error Address" line.long 0x18 "MULTI_ERR_DATA,Multiple Error Read Data" hexmask.long 0x18 0.--31. 1. "MULTI_ERR_DATA,Multiple Error Read Data" line.long 0x1C "MULTI_ERR_ECC,Multiple Error ECC code" hexmask.long 0x1C 0.--31. 1. "MULTI_ERR_ECC,Multiple Error ECC code" line.long 0x20 "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" hexmask.long.tbyte 0x20 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x20 0.--7. 1. "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" group.long 0x3C++0x1F line.long 0x0 "ECC_BASE_ADDR0,ECC Region 0 Base Address" hexmask.long 0x0 0.--31. 1. "ECC_BASE_ADDR0,ECC Region 0 Base Address" line.long 0x4 "ECC_END_ADDR0,ECC Region 0 End Address" hexmask.long 0x4 0.--31. 1. "ECC_END_ADDR0,ECC Region 0 End Address" line.long 0x8 "ECC_BASE_ADDR1,ECC Region 1 Base Address" hexmask.long 0x8 0.--31. 1. "ECC_BASE_ADDR1,ECC Region 1 Base Address" line.long 0xC "ECC_END_ADDR1,ECC Region 1 End Address" hexmask.long 0xC 0.--31. 1. "ECC_END_ADDR1,ECC Region 1 End Address" line.long 0x10 "ECC_BASE_ADDR2,ECC Region 2 Base Address" hexmask.long 0x10 0.--31. 1. "ECC_BASE_ADDR2,ECC Region 2 Base Address" line.long 0x14 "ECC_END_ADDR2,ECC Region 2 End Address" hexmask.long 0x14 0.--31. 1. "ECC_END_ADDR2,ECC Region 2 End Address" line.long 0x18 "ECC_BASE_ADDR3,ECC Region 3 Base Address" hexmask.long 0x18 0.--31. 1. "ECC_BASE_ADDR3,ECC Region 3 Base Address" line.long 0x1C "ECC_END_ADDR3,ECC Region 3 End Address" hexmask.long 0x1C 0.--31. 1. "ECC_END_ADDR3,ECC Region 3 End Address" tree.end tree "XECC_SEMC" base ad:0x40024000 group.long 0x0++0x17 line.long 0x0 "ECC_CTRL,ECC Control Register" bitfld.long 0x0 3. "SWAP_EN,Swap Data Enable" "0: Disable,1: Enable" bitfld.long 0x0 2. "RECC_EN,Read ECC Function Enable" "0: Disable,1: Enable" newline bitfld.long 0x0 1. "WECC_EN,Write ECC Encode Function Enable" "0: Disable,1: Enable" bitfld.long 0x0 0. "ECC_EN,ECC Function Enable" "0: Disable,1: Enable" line.long 0x4 "ERR_STATUS,Error Interrupt Status Register" hexmask.long 0x4 2.--31. 1. "Reserved1,Reserved" eventfld.long 0x4 1. "MULTI_ERR,Multiple Bits Error" "0: Multiple bits error does not happen.,1: Multiple bits error happens." newline eventfld.long 0x4 0. "SINGLE_ERR,Single Bit Error" "0: Single bit error does not happen.,1: Single bit error happens." line.long 0x8 "ERR_STAT_EN,Error Interrupt Status Enable Register" hexmask.long 0x8 2.--31. 1. "Reserved1,Reserved" bitfld.long 0x8 1. "MULIT_ERR_STAT_EN,Multiple Bits Error Status Enable" "0: Masked,1: Enabled" newline bitfld.long 0x8 0. "SINGLE_ERR_STAT_EN,Single Bit Error Status Enable" "0: Masked,1: Enabled" line.long 0xC "ERR_SIG_EN,Error Interrupt Enable Register" hexmask.long 0xC 2.--31. 1. "Reserved1,Reserved" bitfld.long 0xC 1. "MULTI_ERR_SIG_EN,Multiple Bits Error Interrupt Enable" "0: Masked,1: Enabled" newline bitfld.long 0xC 0. "SINGLE_ERR_SIG_EN,Single Bit Error Interrupt Enable" "0: Masked,1: Enabled" line.long 0x10 "ERR_DATA_INJ,Error Injection On Write Data" hexmask.long 0x10 0.--31. 1. "ERR_DATA_INJ,Error Injection On Write Data" line.long 0x14 "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" hexmask.long 0x14 0.--31. 1. "ERR_ECC_INJ,Error Injection On ECC Code of Write Data" rgroup.long 0x18++0x23 line.long 0x0 "SINGLE_ERR_ADDR,Single Error Address" hexmask.long 0x0 0.--31. 1. "SINGLE_ERR_ADDR,Single Error Address" line.long 0x4 "SINGLE_ERR_DATA,Single Error Read Data" hexmask.long 0x4 0.--31. 1. "SINGLE_ERR_DATA,Single Error Read Data" line.long 0x8 "SINGLE_ERR_ECC,Single Error ECC Code" hexmask.long 0x8 0.--31. 1. "SINGLE_ERR_ECC,Single Error ECC code" line.long 0xC "SINGLE_ERR_POS,Single Error Bit Position" hexmask.long 0xC 0.--31. 1. "SINGLE_ERR_POS,Single Error bit Position" line.long 0x10 "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" hexmask.long.tbyte 0x10 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x10 0.--7. 1. "SINGLE_ERR_BIT_FIELD,Single Error Bit Field" line.long 0x14 "MULTI_ERR_ADDR,Multiple Error Address" hexmask.long 0x14 0.--31. 1. "MULTI_ERR_ADDR,Multiple Error Address" line.long 0x18 "MULTI_ERR_DATA,Multiple Error Read Data" hexmask.long 0x18 0.--31. 1. "MULTI_ERR_DATA,Multiple Error Read Data" line.long 0x1C "MULTI_ERR_ECC,Multiple Error ECC code" hexmask.long 0x1C 0.--31. 1. "MULTI_ERR_ECC,Multiple Error ECC code" line.long 0x20 "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" hexmask.long.tbyte 0x20 8.--31. 1. "Reserved1,Reserved" hexmask.long.byte 0x20 0.--7. 1. "MULTI_ERR_BIT_FIELD,Multiple Error Bit Field" group.long 0x3C++0x1F line.long 0x0 "ECC_BASE_ADDR0,ECC Region 0 Base Address" hexmask.long 0x0 0.--31. 1. "ECC_BASE_ADDR0,ECC Region 0 Base Address" line.long 0x4 "ECC_END_ADDR0,ECC Region 0 End Address" hexmask.long 0x4 0.--31. 1. "ECC_END_ADDR0,ECC Region 0 End Address" line.long 0x8 "ECC_BASE_ADDR1,ECC Region 1 Base Address" hexmask.long 0x8 0.--31. 1. "ECC_BASE_ADDR1,ECC Region 1 Base Address" line.long 0xC "ECC_END_ADDR1,ECC Region 1 End Address" hexmask.long 0xC 0.--31. 1. "ECC_END_ADDR1,ECC Region 1 End Address" line.long 0x10 "ECC_BASE_ADDR2,ECC Region 2 Base Address" hexmask.long 0x10 0.--31. 1. "ECC_BASE_ADDR2,ECC Region 2 Base Address" line.long 0x14 "ECC_END_ADDR2,ECC Region 2 End Address" hexmask.long 0x14 0.--31. 1. "ECC_END_ADDR2,ECC Region 2 End Address" line.long 0x18 "ECC_BASE_ADDR3,ECC Region 3 Base Address" hexmask.long 0x18 0.--31. 1. "ECC_BASE_ADDR3,ECC Region 3 Base Address" line.long 0x1C "ECC_END_ADDR3,ECC Region 3 End Address" hexmask.long 0x1C 0.--31. 1. "ECC_END_ADDR3,ECC Region 3 End Address" tree.end tree.end tree "XRDC2" base ad:0x0 tree "XRDC2_D0" base ad:0x40CE0000 group.long 0x0++0x3 line.long 0x0 "MCR,Module Control Register" bitfld.long 0x0 4.--5. "GCL,Global Configuration Lock" "0: Lock disabled registers can be written by any..,1: Lock disabled until the next reset registers can..,2: Lock enabled only the global configuration lock..,3: Lock enabled all registers are read only until.." bitfld.long 0x0 1. "GVLDC,Global Valid Access Control" "0: Access controls are disabled XRDC2 allows all..,1: Access controls are enabled." bitfld.long 0x0 0. "GVLDM,Global Valid MDAC" "0: MDACs are disabled.,1: MDACs are enabled." rgroup.long 0x4++0x3 line.long 0x0 "SR,Status Register" hexmask.long.byte 0x0 8.--11. 1. "GCLO,Global Configuration Lock Owner" hexmask.long.byte 0x0 4.--7. 1. "HRL,Hardware Revision Level" hexmask.long.byte 0x0 0.--3. 1. "DIN,Domain Identifier Number" repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CE1000 ad:0x40CE1008 ad:0x40CE1010 ad:0x40CE1018 ad:0x40CE1020 ad:0x40CE1028 ad:0x40CE1030 ad:0x40CE1038 ad:0x40CE1040 ad:0x40CE1048 ad:0x40CE1050 ad:0x40CE1058 ad:0x40CE1060 ad:0x40CE1068 ad:0x40CE1070 ad:0x40CE1078) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CE1080 ad:0x40CE1088 ad:0x40CE1090 ad:0x40CE1098 ad:0x40CE10A0 ad:0x40CE10A8 ad:0x40CE10B0 ad:0x40CE10B8 ad:0x40CE10C0 ad:0x40CE10C8 ad:0x40CE10D0 ad:0x40CE10D8 ad:0x40CE10E0 ad:0x40CE10E8 ad:0x40CE10F0 ad:0x40CE10F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list ad:0x40CE1100 ad:0x40CE1108 ad:0x40CE1110 ad:0x40CE1118 ad:0x40CE1120 ad:0x40CE1128 ad:0x40CE1130 ad:0x40CE1138 ad:0x40CE1140 ad:0x40CE1148 ad:0x40CE1150 ad:0x40CE1158 ad:0x40CE1160 ad:0x40CE1168 ad:0x40CE1170 ad:0x40CE1178) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list ad:0x40CE1180 ad:0x40CE1188 ad:0x40CE1190 ad:0x40CE1198 ad:0x40CE11A0 ad:0x40CE11A8 ad:0x40CE11B0 ad:0x40CE11B8 ad:0x40CE11C0 ad:0x40CE11C8 ad:0x40CE11D0 ad:0x40CE11D8 ad:0x40CE11E0 ad:0x40CE11E8 ad:0x40CE11F0 ad:0x40CE11F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list ad:0x40CE1200 ad:0x40CE1208 ad:0x40CE1210 ad:0x40CE1218 ad:0x40CE1220 ad:0x40CE1228 ad:0x40CE1230 ad:0x40CE1238 ad:0x40CE1240 ad:0x40CE1248 ad:0x40CE1250 ad:0x40CE1258 ad:0x40CE1260 ad:0x40CE1268 ad:0x40CE1270 ad:0x40CE1278) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list ad:0x40CE1280 ad:0x40CE1288 ad:0x40CE1290 ad:0x40CE1298 ad:0x40CE12A0 ad:0x40CE12A8 ad:0x40CE12B0 ad:0x40CE12B8 ad:0x40CE12C0 ad:0x40CE12C8 ad:0x40CE12D0 ad:0x40CE12D8 ad:0x40CE12E0 ad:0x40CE12E8 ad:0x40CE12F0 ad:0x40CE12F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list ad:0x40CE1300 ad:0x40CE1308 ad:0x40CE1310 ad:0x40CE1318 ad:0x40CE1320 ad:0x40CE1328 ad:0x40CE1330 ad:0x40CE1338 ad:0x40CE1340 ad:0x40CE1348 ad:0x40CE1350 ad:0x40CE1358 ad:0x40CE1360 ad:0x40CE1368 ad:0x40CE1370 ad:0x40CE1378) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list ad:0x40CE1380 ad:0x40CE1388 ad:0x40CE1390 ad:0x40CE1398 ad:0x40CE13A0 ad:0x40CE13A8 ad:0x40CE13B0 ad:0x40CE13B8 ad:0x40CE13C0 ad:0x40CE13C8 ad:0x40CE13D0 ad:0x40CE13D8 ad:0x40CE13E0 ad:0x40CE13E8 ad:0x40CE13F0 ad:0x40CE13F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CE2000 ad:0x40CE2100 ad:0x40CE2200 ad:0x40CE2300 ad:0x40CE2400 ad:0x40CE2500 ad:0x40CE2600 ad:0x40CE2700 ad:0x40CE2800 ad:0x40CE2900 ad:0x40CE2A00 ad:0x40CE2B00 ad:0x40CE2C00 ad:0x40CE2D00 ad:0x40CE2E00 ad:0x40CE2F00) tree "mdaci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x0 0x8 0x10 0x18 0x20 0x28 0x30 0x38 0x40 0x48 0x50 0x58 0x60 0x68 0x70 0x78) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x80 0x88 0x90 0x98 0xA0 0xA8 0xB0 0xB8 0xC0 0xC8 0xD0 0xD8 0xE0 0xE8 0xF0 0xF8) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CE3000 ad:0x40CE3100 ad:0x40CE3200 ad:0x40CE3300 ad:0x40CE3400 ad:0x40CE3500 ad:0x40CE3600 ad:0x40CE3700 ad:0x40CE3800 ad:0x40CE3900 ad:0x40CE3A00 ad:0x40CE3B00 ad:0x40CE3C00 ad:0x40CE3D00 ad:0x40CE3E00 ad:0x40CE3F00) tree "mdaci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x0 0x8 0x10 0x18 0x20 0x28 0x30 0x38 0x40 0x48 0x50 0x58 0x60 0x68 0x70 0x78) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x80 0x88 0x90 0x98 0xA0 0xA8 0xB0 0xB8 0xC0 0xC8 0xD0 0xD8 0xE0 0xE8 0xF0 0xF8) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end tree.end repeat.end repeat 8. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7)(list ad:0x40CE4000 ad:0x40CE4800 ad:0x40CE5000 ad:0x40CE5800 ad:0x40CE6000 ad:0x40CE6800 ad:0x40CE7000 ad:0x40CE7800) tree "paci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x0 0x8 0x10 0x18 0x20 0x28 0x30 0x38 0x40 0x48 0x50 0x58 0x60 0x68 0x70 0x78) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x80 0x88 0x90 0x98 0xA0 0xA8 0xB0 0xB8 0xC0 0xC8 0xD0 0xD8 0xE0 0xE8 0xF0 0xF8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list 0x100 0x108 0x110 0x118 0x120 0x128 0x130 0x138 0x140 0x148 0x150 0x158 0x160 0x168 0x170 0x178) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list 0x180 0x188 0x190 0x198 0x1A0 0x1A8 0x1B0 0x1B8 0x1C0 0x1C8 0x1D0 0x1D8 0x1E0 0x1E8 0x1F0 0x1F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list 0x200 0x208 0x210 0x218 0x220 0x228 0x230 0x238 0x240 0x248 0x250 0x258 0x260 0x268 0x270 0x278) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list 0x280 0x288 0x290 0x298 0x2A0 0x2A8 0x2B0 0x2B8 0x2C0 0x2C8 0x2D0 0x2D8 0x2E0 0x2E8 0x2F0 0x2F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list 0x300 0x308 0x310 0x318 0x320 0x328 0x330 0x338 0x340 0x348 0x350 0x358 0x360 0x368 0x370 0x378) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list 0x380 0x388 0x390 0x398 0x3A0 0x3A8 0x3B0 0x3B8 0x3C0 0x3C8 0x3D0 0x3D8 0x3E0 0x3E8 0x3F0 0x3F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C 0x8D 0x8E 0x8F)(list 0x400 0x408 0x410 0x418 0x420 0x428 0x430 0x438 0x440 0x448 0x450 0x458 0x460 0x468 0x470 0x478) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0x9E 0x9F)(list 0x480 0x488 0x490 0x498 0x4A0 0x4A8 0x4B0 0x4B8 0x4C0 0x4C8 0x4D0 0x4D8 0x4E0 0x4E8 0x4F0 0x4F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF)(list 0x500 0x508 0x510 0x518 0x520 0x528 0x530 0x538 0x540 0x548 0x550 0x558 0x560 0x568 0x570 0x578) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF)(list 0x580 0x588 0x590 0x598 0x5A0 0x5A8 0x5B0 0x5B8 0x5C0 0x5C8 0x5D0 0x5D8 0x5E0 0x5E8 0x5F0 0x5F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF)(list 0x600 0x608 0x610 0x618 0x620 0x628 0x630 0x638 0x640 0x648 0x650 0x658 0x660 0x668 0x670 0x678) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC 0xDD 0xDE 0xDF)(list 0x680 0x688 0x690 0x698 0x6A0 0x6A8 0x6B0 0x6B8 0x6C0 0x6C8 0x6D0 0x6D8 0x6E0 0x6E8 0x6F0 0x6F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xE0 0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE 0xEF)(list 0x700 0x708 0x710 0x718 0x720 0x728 0x730 0x738 0x740 0x748 0x750 0x758 0x760 0x768 0x770 0x778) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xF0 0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 0xF7 0xF8 0xF9 0xFA 0xFB 0xFC 0xFD 0xFE 0xFF)(list 0x780 0x788 0x790 0x798 0x7A0 0x7A8 0x7B0 0x7B8 0x7C0 0x7C8 0x7D0 0x7D8 0x7E0 0x7E8 0x7F0 0x7F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CE8000 ad:0x40CE8400 ad:0x40CE8800 ad:0x40CE8C00 ad:0x40CE9000 ad:0x40CE9400 ad:0x40CE9800 ad:0x40CE9C00 ad:0x40CEA000 ad:0x40CEA400 ad:0x40CEA800 ad:0x40CEAC00 ad:0x40CEB000 ad:0x40CEB400 ad:0x40CEB800 ad:0x40CEBC00) tree "mrci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x0 0x20 0x40 0x60 0x80 0xA0 0xC0 0xE0 0x100 0x120 0x140 0x160 0x180 0x1A0 0x1C0 0x1E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x200 0x220 0x240 0x260 0x280 0x2A0 0x2C0 0x2E0 0x300 0x320 0x340 0x360 0x380 0x3A0 0x3C0 0x3E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CEC000 ad:0x40CEC400 ad:0x40CEC800 ad:0x40CECC00 ad:0x40CED000 ad:0x40CED400 ad:0x40CED800 ad:0x40CEDC00 ad:0x40CEE000 ad:0x40CEE400 ad:0x40CEE800 ad:0x40CEEC00 ad:0x40CEF000 ad:0x40CEF400 ad:0x40CEF800 ad:0x40CEFC00) tree "mrci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x0 0x20 0x40 0x60 0x80 0xA0 0xC0 0xE0 0x100 0x120 0x140 0x160 0x180 0x1A0 0x1C0 0x1E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x200 0x220 0x240 0x260 0x280 0x2A0 0x2C0 0x2E0 0x300 0x320 0x340 0x360 0x380 0x3A0 0x3C0 0x3E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end tree.end tree "XRDC2_D1" base ad:0x40CD0000 group.long 0x0++0x3 line.long 0x0 "MCR,Module Control Register" bitfld.long 0x0 4.--5. "GCL,Global Configuration Lock" "0: Lock disabled registers can be written by any..,1: Lock disabled until the next reset registers can..,2: Lock enabled only the global configuration lock..,3: Lock enabled all registers are read only until.." bitfld.long 0x0 1. "GVLDC,Global Valid Access Control" "0: Access controls are disabled XRDC2 allows all..,1: Access controls are enabled." bitfld.long 0x0 0. "GVLDM,Global Valid MDAC" "0: MDACs are disabled.,1: MDACs are enabled." rgroup.long 0x4++0x3 line.long 0x0 "SR,Status Register" hexmask.long.byte 0x0 8.--11. 1. "GCLO,Global Configuration Lock Owner" hexmask.long.byte 0x0 4.--7. 1. "HRL,Hardware Revision Level" hexmask.long.byte 0x0 0.--3. 1. "DIN,Domain Identifier Number" repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CD1000 ad:0x40CD1008 ad:0x40CD1010 ad:0x40CD1018 ad:0x40CD1020 ad:0x40CD1028 ad:0x40CD1030 ad:0x40CD1038 ad:0x40CD1040 ad:0x40CD1048 ad:0x40CD1050 ad:0x40CD1058 ad:0x40CD1060 ad:0x40CD1068 ad:0x40CD1070 ad:0x40CD1078) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CD1080 ad:0x40CD1088 ad:0x40CD1090 ad:0x40CD1098 ad:0x40CD10A0 ad:0x40CD10A8 ad:0x40CD10B0 ad:0x40CD10B8 ad:0x40CD10C0 ad:0x40CD10C8 ad:0x40CD10D0 ad:0x40CD10D8 ad:0x40CD10E0 ad:0x40CD10E8 ad:0x40CD10F0 ad:0x40CD10F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list ad:0x40CD1100 ad:0x40CD1108 ad:0x40CD1110 ad:0x40CD1118 ad:0x40CD1120 ad:0x40CD1128 ad:0x40CD1130 ad:0x40CD1138 ad:0x40CD1140 ad:0x40CD1148 ad:0x40CD1150 ad:0x40CD1158 ad:0x40CD1160 ad:0x40CD1168 ad:0x40CD1170 ad:0x40CD1178) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list ad:0x40CD1180 ad:0x40CD1188 ad:0x40CD1190 ad:0x40CD1198 ad:0x40CD11A0 ad:0x40CD11A8 ad:0x40CD11B0 ad:0x40CD11B8 ad:0x40CD11C0 ad:0x40CD11C8 ad:0x40CD11D0 ad:0x40CD11D8 ad:0x40CD11E0 ad:0x40CD11E8 ad:0x40CD11F0 ad:0x40CD11F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list ad:0x40CD1200 ad:0x40CD1208 ad:0x40CD1210 ad:0x40CD1218 ad:0x40CD1220 ad:0x40CD1228 ad:0x40CD1230 ad:0x40CD1238 ad:0x40CD1240 ad:0x40CD1248 ad:0x40CD1250 ad:0x40CD1258 ad:0x40CD1260 ad:0x40CD1268 ad:0x40CD1270 ad:0x40CD1278) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list ad:0x40CD1280 ad:0x40CD1288 ad:0x40CD1290 ad:0x40CD1298 ad:0x40CD12A0 ad:0x40CD12A8 ad:0x40CD12B0 ad:0x40CD12B8 ad:0x40CD12C0 ad:0x40CD12C8 ad:0x40CD12D0 ad:0x40CD12D8 ad:0x40CD12E0 ad:0x40CD12E8 ad:0x40CD12F0 ad:0x40CD12F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list ad:0x40CD1300 ad:0x40CD1308 ad:0x40CD1310 ad:0x40CD1318 ad:0x40CD1320 ad:0x40CD1328 ad:0x40CD1330 ad:0x40CD1338 ad:0x40CD1340 ad:0x40CD1348 ad:0x40CD1350 ad:0x40CD1358 ad:0x40CD1360 ad:0x40CD1368 ad:0x40CD1370 ad:0x40CD1378) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list ad:0x40CD1380 ad:0x40CD1388 ad:0x40CD1390 ad:0x40CD1398 ad:0x40CD13A0 ad:0x40CD13A8 ad:0x40CD13B0 ad:0x40CD13B8 ad:0x40CD13C0 ad:0x40CD13C8 ad:0x40CD13D0 ad:0x40CD13D8 ad:0x40CD13E0 ad:0x40CD13E8 ad:0x40CD13F0 ad:0x40CD13F8) tree "msci_msac_wk[$1]" base $2 group.long ($2)++0x7 line.long 0x0 "MSC_MSAC_W0,Memory Slot Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MSC_MSAC_W1,Memory Slot Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The MSAC assignment is invalid.,1: The MSAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CD2000 ad:0x40CD2100 ad:0x40CD2200 ad:0x40CD2300 ad:0x40CD2400 ad:0x40CD2500 ad:0x40CD2600 ad:0x40CD2700 ad:0x40CD2800 ad:0x40CD2900 ad:0x40CD2A00 ad:0x40CD2B00 ad:0x40CD2C00 ad:0x40CD2D00 ad:0x40CD2E00 ad:0x40CD2F00) tree "mdaci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x10000 0x10008 0x10010 0x10018 0x10020 0x10028 0x10030 0x10038 0x10040 0x10048 0x10050 0x10058 0x10060 0x10068 0x10070 0x10078) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x10080 0x10088 0x10090 0x10098 0x100A0 0x100A8 0x100B0 0x100B8 0x100C0 0x100C8 0x100D0 0x100D8 0x100E0 0x100E8 0x100F0 0x100F8) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CD3000 ad:0x40CD3100 ad:0x40CD3200 ad:0x40CD3300 ad:0x40CD3400 ad:0x40CD3500 ad:0x40CD3600 ad:0x40CD3700 ad:0x40CD3800 ad:0x40CD3900 ad:0x40CD3A00 ad:0x40CD3B00 ad:0x40CD3C00 ad:0x40CD3D00 ad:0x40CD3E00 ad:0x40CD3F00) tree "mdaci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x10000 0x10008 0x10010 0x10018 0x10020 0x10028 0x10030 0x10038 0x10040 0x10048 0x10050 0x10058 0x10060 0x10068 0x10070 0x10078) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x10080 0x10088 0x10090 0x10098 0x100A0 0x100A8 0x100B0 0x100B8 0x100C0 0x100C8 0x100D0 0x100D8 0x100E0 0x100E8 0x100F0 0x100F8) tree "mdaci_mdaj[$1]" group.long ($2)++0x7 line.long 0x0 "MDAC_MDA_W0,Master Domain Assignment" hexmask.long.word 0x0 16.--31. 1. "MATCH,Match" hexmask.long.word 0x0 0.--15. 1. "MASK,Mask" line.long 0x4 "MDAC_MDA_W1,Master Domain Assignment" bitfld.long 0x4 31. "VLD,Valid" "0: The MDA is invalid.,1: The MDA is valid." bitfld.long 0x4 30. "DL,Descriptor Lock" "0: Lock disabled registers can be written.,1: Lock enabled registers are read-only until the.." newline bitfld.long 0x4 26.--27. "SA,Secure attribute" "0: Use the bus master's secure/nonsecure attribute..,1: Use the bus master's secure/nonsecure attribute..,2: Force the bus attribute for this master to secure.,3: Force the bus attribute for this master to.." bitfld.long 0x4 24.--25. "PA,Privileged attribute" "0: Use the bus master's privileged/user attribute..,1: Use the bus master's privileged/user attribute..,2: Force the bus attribute for this master to user.,3: Force the bus attribute for this master to.." newline hexmask.long.byte 0x4 16.--19. 1. "DID,Domain Identifier" tree.end repeat.end tree.end repeat.end repeat 8. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7)(list ad:0x40CD4000 ad:0x40CD4800 ad:0x40CD5000 ad:0x40CD5800 ad:0x40CD6000 ad:0x40CD6800 ad:0x40CD7000 ad:0x40CD7800) tree "paci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x10000 0x10008 0x10010 0x10018 0x10020 0x10028 0x10030 0x10038 0x10040 0x10048 0x10050 0x10058 0x10060 0x10068 0x10070 0x10078) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x10080 0x10088 0x10090 0x10098 0x100A0 0x100A8 0x100B0 0x100B8 0x100C0 0x100C8 0x100D0 0x100D8 0x100E0 0x100E8 0x100F0 0x100F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F)(list 0x10100 0x10108 0x10110 0x10118 0x10120 0x10128 0x10130 0x10138 0x10140 0x10148 0x10150 0x10158 0x10160 0x10168 0x10170 0x10178) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F)(list 0x10180 0x10188 0x10190 0x10198 0x101A0 0x101A8 0x101B0 0x101B8 0x101C0 0x101C8 0x101D0 0x101D8 0x101E0 0x101E8 0x101F0 0x101F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F)(list 0x10200 0x10208 0x10210 0x10218 0x10220 0x10228 0x10230 0x10238 0x10240 0x10248 0x10250 0x10258 0x10260 0x10268 0x10270 0x10278) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F)(list 0x10280 0x10288 0x10290 0x10298 0x102A0 0x102A8 0x102B0 0x102B8 0x102C0 0x102C8 0x102D0 0x102D8 0x102E0 0x102E8 0x102F0 0x102F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F)(list 0x10300 0x10308 0x10310 0x10318 0x10320 0x10328 0x10330 0x10338 0x10340 0x10348 0x10350 0x10358 0x10360 0x10368 0x10370 0x10378) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x70 0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E 0x7F)(list 0x10380 0x10388 0x10390 0x10398 0x103A0 0x103A8 0x103B0 0x103B8 0x103C0 0x103C8 0x103D0 0x103D8 0x103E0 0x103E8 0x103F0 0x103F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C 0x8D 0x8E 0x8F)(list 0x10400 0x10408 0x10410 0x10418 0x10420 0x10428 0x10430 0x10438 0x10440 0x10448 0x10450 0x10458 0x10460 0x10468 0x10470 0x10478) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0x9E 0x9F)(list 0x10480 0x10488 0x10490 0x10498 0x104A0 0x104A8 0x104B0 0x104B8 0x104C0 0x104C8 0x104D0 0x104D8 0x104E0 0x104E8 0x104F0 0x104F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF)(list 0x10500 0x10508 0x10510 0x10518 0x10520 0x10528 0x10530 0x10538 0x10540 0x10548 0x10550 0x10558 0x10560 0x10568 0x10570 0x10578) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF)(list 0x10580 0x10588 0x10590 0x10598 0x105A0 0x105A8 0x105B0 0x105B8 0x105C0 0x105C8 0x105D0 0x105D8 0x105E0 0x105E8 0x105F0 0x105F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF)(list 0x10600 0x10608 0x10610 0x10618 0x10620 0x10628 0x10630 0x10638 0x10640 0x10648 0x10650 0x10658 0x10660 0x10668 0x10670 0x10678) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC 0xDD 0xDE 0xDF)(list 0x10680 0x10688 0x10690 0x10698 0x106A0 0x106A8 0x106B0 0x106B8 0x106C0 0x106C8 0x106D0 0x106D8 0x106E0 0x106E8 0x106F0 0x106F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xE0 0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE 0xEF)(list 0x10700 0x10708 0x10710 0x10718 0x10720 0x10728 0x10730 0x10738 0x10740 0x10748 0x10750 0x10758 0x10760 0x10768 0x10770 0x10778) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0xF0 0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 0xF7 0xF8 0xF9 0xFA 0xFB 0xFC 0xFD 0xFE 0xFF)(list 0x10780 0x10788 0x10790 0x10798 0x107A0 0x107A8 0x107B0 0x107B8 0x107C0 0x107C8 0x107D0 0x107D8 0x107E0 0x107E8 0x107F0 0x107F8) tree "paci_pdacj[$1]" group.long ($2)++0x7 line.long 0x0 "PAC_PDAC_W0,Peripheral Domain Access Control" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "PAC_PDAC_W1,Peripheral Domain Access Control" bitfld.long 0x4 31. "VLD,Valid" "0: The PDAC assignment is invalid.,1: The PDAC assignment is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be..,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40CD8000 ad:0x40CD8400 ad:0x40CD8800 ad:0x40CD8C00 ad:0x40CD9000 ad:0x40CD9400 ad:0x40CD9800 ad:0x40CD9C00 ad:0x40CDA000 ad:0x40CDA400 ad:0x40CDA800 ad:0x40CDAC00 ad:0x40CDB000 ad:0x40CDB400 ad:0x40CDB800 ad:0x40CDBC00) tree "mrci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x10000 0x10020 0x10040 0x10060 0x10080 0x100A0 0x100C0 0x100E0 0x10100 0x10120 0x10140 0x10160 0x10180 0x101A0 0x101C0 0x101E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x10200 0x10220 0x10240 0x10260 0x10280 0x102A0 0x102C0 0x102E0 0x10300 0x10320 0x10340 0x10360 0x10380 0x103A0 0x103C0 0x103E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40CDC000 ad:0x40CDC400 ad:0x40CDC800 ad:0x40CDCC00 ad:0x40CDD000 ad:0x40CDD400 ad:0x40CDD800 ad:0x40CDDC00 ad:0x40CDE000 ad:0x40CDE400 ad:0x40CDE800 ad:0x40CDEC00 ad:0x40CDF000 ad:0x40CDF400 ad:0x40CDF800 ad:0x40CDFC00) tree "mrci[$1]" base $2 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list 0x10000 0x10020 0x10040 0x10060 0x10080 0x100A0 0x100C0 0x100E0 0x10100 0x10120 0x10140 0x10160 0x10180 0x101A0 0x101C0 0x101E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list 0x10200 0x10220 0x10240 0x10260 0x10280 0x102A0 0x102C0 0x102E0 0x10300 0x10320 0x10340 0x10360 0x10380 0x103A0 0x103C0 0x103E0) tree "mrci_mrgdj[$1]" group.long ($2)++0xF line.long 0x0 "MRC_MRGD_W0,Memory Region Descriptor" hexmask.long.tbyte 0x0 12.--31. 1. "SRTADDR,Start Address" line.long 0x4 "MRC_MRGD_W1,Memory Region Descriptor" hexmask.long.byte 0x4 0.--3. 1. "SRTADDR,Start Address" line.long 0x8 "MRC_MRGD_W2,Memory Region Descriptor" hexmask.long.tbyte 0x8 12.--31. 1. "ENDADDR,End Address" line.long 0xC "MRC_MRGD_W3,Memory Region Descriptor" hexmask.long.byte 0xC 0.--3. 1. "ENDADDR,End Address" group.long ($2+0x14)++0x7 line.long 0x0 "MRC_MRGD_W5,Memory Region Descriptor" hexmask.long.byte 0x0 24.--27. 1. "EALO,Exclusive Access Lock Owner" bitfld.long 0x0 21.--23. "D7ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 18.--20. "D6ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 15.--17. "D5ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 12.--14. "D4ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 9.--11. "D3ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 6.--8. "D2ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3.--5. "D1ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x0 0.--2. "D0ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" line.long 0x4 "MRC_MRGD_W6,Memory Region Descriptor" bitfld.long 0x4 31. "VLD,Valid" "0: The MRGD is invalid.,1: The MRGD is valid." bitfld.long 0x4 29.--30. "DL2,Descriptor Lock" "0: Lock disabled descriptor registers can be written.,1: Lock disabled until the next reset descriptor..,2: Lock enabled only domain 'x' can only update the..,3: Lock enabled descriptor registers are read-only.." newline bitfld.long 0x4 24.--25. "EAL,Exclusive Access Lock" "0: Lock disabled.,1: Lock disabled until next reset.,2: Lock enabled lock state = available.,3: Lock enabled lock state = not available." bitfld.long 0x4 21.--23. "D15ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 18.--20. "D14ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 15.--17. "D13ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 12.--14. "D12ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 9.--11. "D11ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 6.--8. "D10ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" bitfld.long 0x4 3.--5. "D9ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" newline bitfld.long 0x4 0.--2. "D8ACP,Domain 'x' access control policy" "0,1,2,3,4,5,6,7" tree.end repeat.end tree.end repeat.end tree.end tree.end AUTOINDENT.OFF