; -------------------------------------------------------------------------------- ; @Title: Cirrus Logic EP9312 On-Chip Peripherals ; @Props: Released ; @Author: PIO ETA ; @Date: 2005-09-02 ; @Manufacturer: Cirrus Logic ; @Core: ARM920T ; @Copyright: (c) 1989-2014 Lauterbach GmbH, licensed for use with TRACE32(R) only ; -------------------------------------------------------------------------------- ; $Id: perep9312.per 15986 2023-04-17 14:06:49Z bschroefel $ config 16. 8. width 16. 8. base d:0x00000000 tree "System Controller" base asd:0x80930000 ;begin include file ep9312/system.ph ;parameters: rgroup asd:0x0000++3 line.long 0x00 "PwrSts,Power/State Control State Register" hexmask.long.byte 0x00 24.--31. 1. " CHIPMAN ,Chip Manufacturer" hexmask.long.byte 0x00 16.--23. 1. " CHIPID ,Chip ID Bits" textline " " bitfld.long 0x00 15. " WDTFLG ,Watchdog Timer Flag" "Cleared,Reset" bitfld.long 0x00 13. " CLDFLG ,Clod Start Flag" "Cleared,Power-on-Reset" textline " " bitfld.long 0x00 12. " TEST_RESET ,Test Reset Flag" "Not activated,Activated" bitfld.long 0x00 11. " RSTFLG ,Reset Flag" "Cleared,Reset pressed" textline " " bitfld.long 0x00 10. " SW_RESET ,Software Reset Flag" "Not activated,Activated" bitfld.long 0x00 9. " PLL2_LOCK_REG ,Registered PLL1 Clock" "Cleared,Set" textline " " bitfld.long 0x00 8. " PLL2_LOCK ,PLL2 Lock" "Not locked,Locked" bitfld.long 0x00 7. " PLL1_LOCK_REG ,Registered PLL1 Clock" "Cleared,Set" textline " " bitfld.long 0x00 6. " PLL1_LOCK ,PLL1 Lock" "Not locked,Locked" hexmask.long.byte 0x00 0.--5. 1. " RTCDIV ,RTC Divider" group asd:0x0004++3 line.long 0x00 "PwrCnt,Clock/Debug Control Status Register" bitfld.long 0x00 31. " FIR_EN ,Gate FIRCLK to IrDA" "Off,On" bitfld.long 0x00 29. " UARTBAUD ,UART Baud Rate" "Divided by 2,Full speed" textline " " bitfld.long 0x00 28. " USH_EN ,Gate HCLK to the USB Host Block" "Off,On" bitfld.long 0x00 27. " DMAM2MCH1 ,DMA Controller Channel M1 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " DMAM2MCH0 ,DMA Controller Channel M0 Enable" "Disabled,Enabled" bitfld.long 0x00 25. " DMAM2PCH8 ,DMA Controller Channel P8 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 24. " DMAM2PCH9 ,DMA Controller Channel P9 Enable" "Disabled,Enabled" bitfld.long 0x00 23. " DMAM2PCH6 ,DMA Controller Channel P6 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 22. " DMAM2PCH7 ,DMA Controller Channel P7 Enable" "Disabled,Enabled" bitfld.long 0x00 21. " DMAM2PCH4 ,DMA Controller Channel P4 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 20. " DMAM2PCH5 ,DMA Controller Channel P5 Enable" "Disabled,Enabled" bitfld.long 0x00 19. " DMAM2PCH2 ,DMA Controller Channel P2 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " DMAM2PCH3 ,DMA Controller Channel P3 Enable" "Disabled,Enabled" bitfld.long 0x00 17. " DMAM2PCH0 ,DMA Controller Channel P0 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 16. " DMAM2PCH1 ,DMA Controller Channel P1 Enable" "Disabled,Enabled" rgroup asd:0x0008++3 line.long 0x00 "Halt,Halt Mode when Reading" rgroup asd:0x000C++3 line.long 0x00 "Standby,Standby Mode when Readnig" wgroup asd:0x0018++3 line.long 0x00 "TEOI,When Write Clearing Tick Interrupt" wgroup asd:0x001C++3 line.long 0x00 "STFClr,Clear CLDFLG RSTFLG WDTFLG when Write" group asd:0x0020++7 line.long 0x00 "ClkSet1,Clock Speed Control 1 Register" bitfld.long 0x00 25.--27. " FCLKDIV ,Divider Ratio Between VOC and Processor Clock" "1,2,4,8,16,Reserved..." bitfld.long 0x00 24. " SMCROM ,Gate off HCLK to Static Memory Controller" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " nBYP ,Processor Clock Dividers" "External clock,PLL Clock" bitfld.long 0x00 20.--22. " HCLKDIV ,Divider Ratio Between VCO and HCLK" "1,2,4,5,6,8,16,32" textline " " bitfld.long 0x00 18.--19. " PLCKDIV ,Ratio Divider Between HCLK AHB and APB Clock" "1,2,4,8" bitfld.long 0x00 16.--17. " PLL1_PS ,VCO Clock in PLL1 Divider" "1,2,4,8" textline " " hexmask.long.byte 0x00 11.--15. 1. " PLL1X2FBD1 ,Second Feedback Divider for PLL1" hexmask.long.byte 0x00 5.--10. 1. " PLL1X2FBD2 ,First Feedback Divider for PLL1" textline " " hexmask.long.byte 0x00 0.--4. 1. " PLL1X2IPD ,Input Divider for PLL1" line.long 0x04 "ClkSet2,Clock Speed Control 2 Register" hexmask.long.byte 0x04 28.--31. 1. " USBDIV ,Divide ratio for USB Clock" bitfld.long 0x04 19. " nBYP2 ,Clock Source for Processor Clock Dividers" "External clock,PLL2" textline " " bitfld.long 0x04 18. " PLL2_EN ,PLL2 Enable" "Disabled,Enabled" bitfld.long 0x04 16.--17. " PLL2_PS ,Final Divide of VCO Clock" "1,2,4,8" textline " " hexmask.long.byte 0x04 11.--15. 1. " PLL2X2FBD1 ,Second Feedback Divider for PLL2" hexmask.long.byte 0x04 5.--10. 1. " PLL2X2FBD2 ,First Feedback Divider for PLL2" textline " " hexmask.long.byte 0x04 0.--4. 1. " PLL2X2IPD ,Input Divider for PLL2" group asd:0x0040++7 line.long 0x00 "ScratchReg0,Scratch Register 0" hexfld.long 0x00 " Value ,Scratch Register 0 Value" line.long 0x04 "ScratchReg1,Scratch Register 1" hexfld.long 0x04 " Value ,Scratch Register 1 Value" group asd:0x0050++7 line.long 0x00 "APBWait,APB Wait Register" bitfld.long 0x00 0. " NO_WRITE_WAIT ,Wait State Adding for AHB/APB" "No,Yes" line.long 0x04 "BusMstrArb,Bus Master Arbitration Register" bitfld.long 0x04 9. " MACENFIQ ,MAC form AHB Requests Ignore if FIQ Active" "Allowed,Ignored" bitfld.long 0x04 8. " MACENIRQ ,MAC form AHB Requests Ignore" "Allowed,Ignored" textline " " bitfld.long 0x04 7. " USHENFIQ ,USB form AHB Requests Ignore if FIQ Active" "Allowed,Ignored" bitfld.long 0x04 6. " USHENIRQ ,USB form AHB Requests Ignore" "Allowed,Ignored" textline " " bitfld.long 0x04 5. " DMAENFIQ ,DMA form AHB Requests Ignore if FIQ Active" "Allowed,Ignored" bitfld.long 0x04 4. " DMAENIRQ ,DMA form AHB Requests Ignore" "Allowed,Ignored" textline " " bitfld.long 0x04 3. " PRICORE ,Core Priority Select" "Normal,Highest" bitfld.long 0x04 0.--1. " PRI_ORD ,Priority of AHB Arbiter" "PRIOR00,PRIOR01,PRIOR10,PRIOR11" wgroup asd:0x0058++3 line.long 0x00 "BootModeClr,Boot Mode Clear Register" group asd:0x0080++0x0F line.long 0x00 "DeviceCfg,Device Configuration Register" bitfld.long 0x00 31. " SWRST ,Software Reset" "Low,High" bitfld.long 0x00 30. " D1onG ,External DMA1 Hardware Handshake Signals Mapped to EGPIO Pins" "Not supported,Mapped" textline " " bitfld.long 0x00 29. " D0onG ,External DMA0 Hardware Handshake Signals Mapped to EGPIO Pins" "Not supported,Mapped" bitfld.long 0x00 28. " IonU2 ,IrDA on UART2" "UART,IrDA" textline " " bitfld.long 0x00 27. " GonK ,GPIO on Key Matrix" "Other options,GPIO" bitfld.long 0x00 26. " TonG ,TENn on GPIO" "Not used,Used" textline " " bitfld.long 0x00 25. " MonG ,Modem on GPIO" "Not used,Used" bitfld.long 0x00 24. " U3EN ,UART3 Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 23. " CPENA ,Co-Processor Enable" "Disabled,Enabled" bitfld.long 0x00 22. " A2onG ,I2S Audio Port 2 on GPIO" "Not used,Mapped" textline " " bitfld.long 0x00 21. " A1onG ,I2S Audio Port 1 on GPIO" "Not used,Mapped" bitfld.long 0x00 20. " U2EN ,UART2 Enable" "Clock active,Clock off" textline " " bitfld.long 0x00 19. " EXVC ,External Video Clock" "Internal,External" bitfld.long 0x00 18. " U1EN ,UART1 Enable" "Clock active,Clock off" textline " " bitfld.long 0x00 17. " TIN ,Touchscreen Controller Inactive" "Inactive,Active" bitfld.long 0x00 15. " HC3IN ,HDLC3 Clock In" "Input,Output" textline " " bitfld.long 0x00 14. " HC3EN ,HDLC3 Clock Enable" "Not used,Enabled" bitfld.long 0x00 13. " HC1IN ,HDLC1 Clock In" "Input,Output" textline " " bitfld.long 0x00 12. " HC1EN ,HDLC1 Clock Enable" "Not used,Enabled" bitfld.long 0x00 11. " HonIDE ,GPIO Port H on IDE Pins" "Disabled,Enabled" textline " " bitfld.long 0x00 10. " GonIDE ,GPIO Port G on IDE Pins" "Disabled,Enabled" bitfld.long 0x00 9. " PonG ,PWM1 Output on EGPIO Pin" "Disabled,Enabled" textline " " bitfld.long 0x00 8. " EonIDE ,GPIO Port E on IDE Pins" "Disabled,Enabled" bitfld.long 0x00 7. " I2SonSSP ,I2S on SSP Pins" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " I2SonAC97 ,I2S on AC97 Pins" "Disabled,Enabled" bitfld.long 0x00 4. " RASOnP3 ,Raster On SDRAM Port 3" "Primary AHB,Private AHB" textline " " bitfld.long 0x00 3. " RAS ,Raster Inactive" "Disabled,Acitve" bitfld.long 0x00 2. " ADCPD ,ADC Power Down" "Power down,Active" textline " " bitfld.long 0x00 1. " KEYS ,Key Matrix Inactive" "Inactive,Active" bitfld.long 0x00 0. " SHena ,Standby/Halt Enable" "Disabled,Enabled" line.long 0x04 "VidClkDiv,Video Clock Divider Register" bitfld.long 0x04 15. " VENA ,Enable VCLK Divider" "Disabled,Enabled" bitfld.long 0x04 14. " ESEL ,External Clock Source Select" "External XTAL1,Internal PLLs" textline " " bitfld.long 0x04 13. " PSEL ,PLL Source Select" "PLL1,PLL2" bitfld.long 0x04 8.--9. " PDIV ,Pre-Divider Value" "Disabled,2,2.5,3" textline " " hexmask.long.byte 0x04 0.--6. 1. " VDIV ,VCLK Divider Value" line.long 0x08 "MIRClkDiv,MIR Clock Divider Register" bitfld.long 0x08 15. " MENA ,Enable MIR_CLK Divider" "Disabled,Enabled" bitfld.long 0x08 14. " ESEL ,External Clock Source Select" "External XTAL1,Internal PLLs" textline " " bitfld.long 0x08 13. " PSEL ,PLL Source Select" "PLL1,PLL2" bitfld.long 0x08 8.--9. " PDIV ,Pre-Divider Value" "Disabled,2,2.5,3" textline " " hexmask.long.byte 0x08 0.--6. 1. " MDIV ,MIR_CLK Divider Value" line.long 0x0C "I2SClkDiv,I2S Audio Clock Divider Register" bitfld.long 0x0C 31. " SENA ,Enable Audio Clock Generation" "Disabled,Enabled" bitfld.long 0x0C 30. " SLAVE ,I2S Slave" "Off,On" textline " " bitfld.long 0x0C 29. " ORIDE ,Override I2S Master Configuration" "Use,Override" bitfld.long 0x0C 20. " DROP ,Drop SCLK Clocks" "No drop,Drop" textline " " bitfld.long 0x0C 19. " SPOL ,SCLK Polarity" "Rising edge,Falling edge" bitfld.long 0x0C 17.--18. " LRDIV ,LRCLK Divide Select" "SCLK/32,SCLK/64,SCLK/128,Reserved" textline " " bitfld.long 0x0C 16. " SDIV ,SCLK Dicide Select" "MCLK/2,MCLK/4" bitfld.long 0x0C 15. " MENA ,Enable Master Clock Generation" "Disabled,Enabled" textline " " bitfld.long 0x0C 14. " ESEL ,External Clock Source Select" "External XTAL1,Internal PLLs" bitfld.long 0x0C 13. " PSEL ,PLL Source Select" "PLL1,PLL2" textline " " bitfld.long 0x0C 8.--9. " PDIV ,Pre-Divider Value" "Disabled,2,2.5,3" hexmask.long.byte 0x0C 0.--6. 1. " MDIV ,MCLK Divider Value" group asd:0x0090++3 line.long 0x00 "KeyTchClkDiv,Keyscan/Touch Clock Divider Register" bitfld.long 0x00 31. " TSEN ,Touchscreen and ADC Clock Enable" "Disabled,Enabled" bitfld.long 0x00 16. " ADIV ,ADC Clock Divider Value" "Divide by 16,Divide by 4" textline " " bitfld.long 0x00 15. " KEN ,Key Matrix Clock Enable" "Disabled,Enabled" bitfld.long 0x00 0. " KDIV ,Key Matrix Clock Divider Value" "Divide by 16,Divide by 4" group asd:0x0094++3 line.long 0x00 "ChipID,Chip ID Register" hexmask.long.byte 0x00 28.--31. 1. " REV ,Revision" hexmask.long.word 0x00 0.--15. 1. " ID ,Chip ID" group asd:0x0098++3 line.long 0x00 "SysCfg,System Configuration Register" hexmask.long.byte 0x00 28.--31. 1. " REV ,Revision" bitfld.long 0x00 8. " SBOOT ,Serial Boot Flag" "Normal,Serial" textline " " bitfld.long 0x00 7. " LCSn7 ,Bus Width for Boot Code" "Low,High" bitfld.long 0x00 6. " LCSn6 ,Bus Width for Boot Code" "Low,High" textline " " bitfld.long 0x00 5. " LASD0 ,Boot Device Type" "Synchronous,Asynchronous" bitfld.long 0x00 4. " LEEDA ,Latched Version of EEDAT Pin" "Low,High" textline " " bitfld.long 0x00 3. " LEECLK ,External/Internal Boot" "External,Internal" bitfld.long 0x00 1. " LCSn2 ,Watchdog Startup Action" "Watchdog disabled,Watchdog active" textline " " bitfld.long 0x00 0. " LCSn1 ,Watchdog Startup Action" "Reset duration disabled,Reset duration active" group asd:0x00C0++3 line.long 0x00 "SysSWLock,Software Lock Register" hexmask.long.byte 0x00 0.--7. 1. " LOCK ,Lock Code Value" ;end include file ep9312/system.ph tree.end tree "Vector Interrupt Controller" base asd:0x80000000 ;begin include file ep9312/interrupt.ph ;parameters: width 18. 8. tree "Vector Interrupt Controller 1(VIC1)" base asd:0x800B0000 ;begin include file ep9312/interrupt/global.ph ;parameters: 1 rgroup asd:0x0000++0x0B line.long 0x00 "VIC1IRQStatus,IRQ Status Register" bitfld.long 0x00 31. " IRQStatus31 ,IRQ Interrupt Status Bit 31" "No interrupt,Interrupt" bitfld.long 0x00 30. " IRQStatus30 ,IRQ Interrupt Status Bit 30" "No interrupt,Interrupt" textline " " bitfld.long 0x00 29. " IRQStatus29 ,IRQ Interrupt Status Bit 29" "No interrupt,Interrupt" bitfld.long 0x00 28. " IRQStatus28 ,IRQ Interrupt Status Bit 28" "No interrupt,Interrupt" textline " " bitfld.long 0x00 27. " IRQStatus27 ,IRQ Interrupt Status Bit 27" "No interrupt,Interrupt" bitfld.long 0x00 26. " IRQStatus26 ,IRQ Interrupt Status Bit 26" "No interrupt,Interrupt" textline " " bitfld.long 0x00 25. " IRQStatus25 ,IRQ Interrupt Status Bit 25" "No interrupt,Interrupt" bitfld.long 0x00 24. " IRQStatus24 ,IRQ Interrupt Status Bit 24" "No interrupt,Interrupt" textline " " bitfld.long 0x00 23. " IRQStatus23 ,IRQ Interrupt Status Bit 23" "No interrupt,Interrupt" bitfld.long 0x00 22. " IRQStatus22 ,IRQ Interrupt Status Bit 22" "No interrupt,Interrupt" textline " " bitfld.long 0x00 21. " IRQStatus21 ,IRQ Interrupt Status Bit 21" "No interrupt,Interrupt" bitfld.long 0x00 20. " IRQStatus20 ,IRQ Interrupt Status Bit 20" "No interrupt,Interrupt" textline " " bitfld.long 0x00 19. " IRQStatus19 ,IRQ Interrupt Status Bit 19" "No interrupt,Interrupt" bitfld.long 0x00 18. " IRQStatus18 ,IRQ Interrupt Status Bit 18" "No interrupt,Interrupt" textline " " bitfld.long 0x00 17. " IRQStatus17 ,IRQ Interrupt Status Bit 17" "No interrupt,Interrupt" bitfld.long 0x00 16. " IRQStatus16 ,IRQ Interrupt Status Bit 16" "No interrupt,Interrupt" textline " " bitfld.long 0x00 15. " IRQStatus15 ,IRQ Interrupt Status Bit 15" "No interrupt,Interrupt" bitfld.long 0x00 14. " IRQStatus14 ,IRQ Interrupt Status Bit 14" "No interrupt,Interrupt" textline " " bitfld.long 0x00 13. " IRQStatus13 ,IRQ Interrupt Status Bit 13" "No interrupt,Interrupt" bitfld.long 0x00 12. " IRQStatus12 ,IRQ Interrupt Status Bit 12" "No interrupt,Interrupt" textline " " bitfld.long 0x00 11. " IRQStatus11 ,IRQ Interrupt Status Bit 11" "No interrupt,Interrupt" bitfld.long 0x00 10. " IRQStatus10 ,IRQ Interrupt Status Bit 10" "No interrupt,Interrupt" textline " " bitfld.long 0x00 9. " IRQStatus9 ,IRQ Interrupt Status Bit 9" "No interrupt,Interrupt" bitfld.long 0x00 8. " IRQStatus8 ,IRQ Interrupt Status Bit 8" "No interrupt,Interrupt" textline " " bitfld.long 0x00 7. " IRQStatus7 ,IRQ Interrupt Status Bit 7" "No interrupt,Interrupt" bitfld.long 0x00 6. " IRQStatus6 ,IRQ Interrupt Status Bit 6" "No interrupt,Interrupt" textline " " bitfld.long 0x00 5. " IRQStatus5 ,IRQ Interrupt Status Bit 5" "No interrupt,Interrupt" bitfld.long 0x00 4. " IRQStatus4 ,IRQ Interrupt Status Bit 4" "No interrupt,Interrupt" textline " " bitfld.long 0x00 3. " IRQStatus3 ,IRQ Interrupt Status Bit 3" "No interrupt,Interrupt" bitfld.long 0x00 2. " IRQStatus2 ,IRQ Interrupt Status Bit 2" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " IRQStatus1 ,IRQ Interrupt Status Bit 1" "No interrupt,Interrupt" bitfld.long 0x00 0. " IRQStatus0 ,IRQ Interrupt Status Bit 0" "No interrupt,Interrupt" line.long 0x04 "VIC1FIQStatus,FIQ Status Register" bitfld.long 0x04 31. " FIQStatus31 ,FIQ Interrupt Status Bit 31" "No interrupt,Interrupt" bitfld.long 0x04 30. " FIQStatus30 ,FIQ Interrupt Status Bit 30" "No interrupt,Interrupt" textline " " bitfld.long 0x04 29. " FIQStatus29 ,FIQ Interrupt Status Bit 29" "No interrupt,Interrupt" bitfld.long 0x04 28. " FIQStatus28 ,FIQ Interrupt Status Bit 28" "No interrupt,Interrupt" textline " " bitfld.long 0x04 27. " FIQStatus27 ,FIQ Interrupt Status Bit 27" "No interrupt,Interrupt" bitfld.long 0x04 26. " FIQStatus26 ,FIQ Interrupt Status Bit 26" "No interrupt,Interrupt" textline " " bitfld.long 0x04 25. " FIQStatus25 ,FIQ Interrupt Status Bit 25" "No interrupt,Interrupt" bitfld.long 0x04 24. " FIQStatus24 ,FIQ Interrupt Status Bit 24" "No interrupt,Interrupt" textline " " bitfld.long 0x04 23. " FIQStatus23 ,FIQ Interrupt Status Bit 23" "No interrupt,Interrupt" bitfld.long 0x04 22. " FIQStatus22 ,FIQ Interrupt Status Bit 22" "No interrupt,Interrupt" textline " " bitfld.long 0x04 21. " FIQStatus21 ,FIQ Interrupt Status Bit 21" "No interrupt,Interrupt" bitfld.long 0x04 20. " FIQStatus20 ,FIQ Interrupt Status Bit 20" "No interrupt,Interrupt" textline " " bitfld.long 0x04 19. " FIQStatus19 ,FIQ Interrupt Status Bit 19" "No interrupt,Interrupt" bitfld.long 0x04 18. " FIQStatus18 ,FIQ Interrupt Status Bit 18" "No interrupt,Interrupt" textline " " bitfld.long 0x04 17. " FIQStatus17 ,FIQ Interrupt Status Bit 17" "No interrupt,Interrupt" bitfld.long 0x04 16. " FIQStatus16 ,FIQ Interrupt Status Bit 16" "No interrupt,Interrupt" textline " " bitfld.long 0x04 15. " FIQStatus15 ,FIQ Interrupt Status Bit 15" "No interrupt,Interrupt" bitfld.long 0x04 14. " FIQStatus14 ,FIQ Interrupt Status Bit 14" "No interrupt,Interrupt" textline " " bitfld.long 0x04 13. " FIQStatus13 ,FIQ Interrupt Status Bit 13" "No interrupt,Interrupt" bitfld.long 0x04 12. " FIQStatus12 ,FIQ Interrupt Status Bit 12" "No interrupt,Interrupt" textline " " bitfld.long 0x04 11. " FIQStatus11 ,FIQ Interrupt Status Bit 11" "No interrupt,Interrupt" bitfld.long 0x04 10. " FIQStatus10 ,FIQ Interrupt Status Bit 10" "No interrupt,Interrupt" textline " " bitfld.long 0x04 9. " FIQStatus9 ,FIQ Interrupt Status Bit 9" "No interrupt,Interrupt" bitfld.long 0x04 8. " FIQStatus8 ,FIQ Interrupt Status Bit 8" "No interrupt,Interrupt" textline " " bitfld.long 0x04 7. " FIQStatus7 ,FIQ Interrupt Status Bit 7" "No interrupt,Interrupt" bitfld.long 0x04 6. " FIQStatus6 ,FIQ Interrupt Status Bit 6" "No interrupt,Interrupt" textline " " bitfld.long 0x04 5. " FIQStatus5 ,FIQ Interrupt Status Bit 5" "No interrupt,Interrupt" bitfld.long 0x04 4. " FIQStatus4 ,FIQ Interrupt Status Bit 4" "No interrupt,Interrupt" textline " " bitfld.long 0x04 3. " FIQStatus3 ,FIQ Interrupt Status Bit 3" "No interrupt,Interrupt" bitfld.long 0x04 2. " FIQStatus2 ,FIQ Interrupt Status Bit 2" "No interrupt,Interrupt" textline " " bitfld.long 0x04 1. " FIQStatus1 ,FIQ Interrupt Status Bit 1" "No interrupt,Interrupt" bitfld.long 0x04 0. " FIQStatus0 ,FIQ Interrupt Status Bit 0" "No interrupt,Interrupt" line.long 0x08 "VIC1RawIntr,Raw Interrupt Status Register" bitfld.long 0x08 31. " RawIntr31 ,Interrupt Status Bit 31 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 30. " RawIntr30 ,Interrupt Status Bit 30 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 29. " RawIntr29 ,Interrupt Status Bit 29 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 28. " RawIntr28 ,Interrupt Status Bit 28 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 27. " RawIntr27 ,Interrupt Status Bit 27 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 26. " RawIntr26 ,Interrupt Status Bit 26 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 25. " RawIntr25 ,Interrupt Status Bit 25 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 24. " RawIntr24 ,Interrupt Status Bit 24 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 23. " RawIntr23 ,Interrupt Status Bit 23 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 22. " RawIntr22 ,Interrupt Status Bit 22 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 21. " RawIntr21 ,Interrupt Status Bit 21 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 20. " RawIntr20 ,Interrupt Status Bit 20 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 19. " RawIntr19 ,Interrupt Status Bit 19 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 18. " RawIntr18 ,Interrupt Status Bit 18 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 17. " RawIntr17 ,Interrupt Status Bit 17 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 16. " RawIntr16 ,Interrupt Status Bit 16 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 15. " RawIntr15 ,Interrupt Status Bit 15 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 14. " RawIntr14 ,Interrupt Status Bit 14 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 13. " RawIntr13 ,Interrupt Status Bit 13 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 12. " RawIntr12 ,Interrupt Status Bit 12 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 11. " RawIntr11 ,Interrupt Status Bit 11 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 10. " RawIntr10 ,Interrupt Status Bit 10 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 9. " RawIntr9 ,Interrupt Status Bit 9 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 8. " RawIntr8 ,Interrupt Status Bit 8 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 7. " RawIntr7 ,Interrupt Status Bit 7 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 6. " RawIntr6 ,Interrupt Status Bit 6 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 5. " RawIntr5 ,Interrupt Status Bit 5 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 4. " RawIntr4 ,Interrupt Status Bit 4 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 3. " RawIntr3 ,Interrupt Status Bit 3 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 2. " RawIntr2 ,Interrupt Status Bit 2 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 1. " RawIntr1 ,Interrupt Status Bit 1 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 0. " RawIntr0 ,Interrupt Status Bit 0 without Masking" "No interrupt,Interrupt" group asd:0x000C++7 line.long 0x00 "VIC1IntSelect,Interrupt Select Register" bitfld.long 0x00 31. " IntSelect31 ,Interrupt Type Select Bit 31" "FIQ,IRQ" bitfld.long 0x00 30. " IntSelect30 ,Interrupt Type Select Bit 30" "FIQ,IRQ" bitfld.long 0x00 29. " IntSelect29 ,Interrupt Type Select Bit 29" "FIQ,IRQ" textline " " bitfld.long 0x00 28. " IntSelect28 ,Interrupt Type Select Bit 28" "FIQ,IRQ" bitfld.long 0x00 27. " IntSelect27 ,Interrupt Type Select Bit 27" "FIQ,IRQ" bitfld.long 0x00 26. " IntSelect26 ,Interrupt Type Select Bit 26" "FIQ,IRQ" textline " " bitfld.long 0x00 25. " IntSelect25 ,Interrupt Type Select Bit 25" "FIQ,IRQ" bitfld.long 0x00 24. " IntSelect24 ,Interrupt Type Select Bit 24" "FIQ,IRQ" bitfld.long 0x00 23. " IntSelect23 ,Interrupt Type Select Bit 23" "FIQ,IRQ" textline " " bitfld.long 0x00 22. " IntSelect22 ,Interrupt Type Select Bit 22" "FIQ,IRQ" bitfld.long 0x00 21. " IntSelect21 ,Interrupt Type Select Bit 21" "FIQ,IRQ" bitfld.long 0x00 20. " IntSelect20 ,Interrupt Type Select Bit 20" "FIQ,IRQ" textline " " bitfld.long 0x00 19. " IntSelect19 ,Interrupt Type Select Bit 19" "FIQ,IRQ" bitfld.long 0x00 18. " IntSelect18 ,Interrupt Type Select Bit 18" "FIQ,IRQ" bitfld.long 0x00 17. " IntSelect17 ,Interrupt Type Select Bit 17" "FIQ,IRQ" textline " " bitfld.long 0x00 16. " IntSelect16 ,Interrupt Type Select Bit 16" "FIQ,IRQ" bitfld.long 0x00 15. " IntSelect15 ,Interrupt Type Select Bit 15" "FIQ,IRQ" bitfld.long 0x00 14. " IntSelect14 ,Interrupt Type Select Bit 14" "FIQ,IRQ" textline " " bitfld.long 0x00 13. " IntSelect13 ,Interrupt Type Select Bit 13" "FIQ,IRQ" bitfld.long 0x00 12. " IntSelect12 ,Interrupt Type Select Bit 12" "FIQ,IRQ" bitfld.long 0x00 11. " IntSelect11 ,Interrupt Type Select Bit 11" "FIQ,IRQ" textline " " bitfld.long 0x00 10. " IntSelect10 ,Interrupt Type Select Bit 10" "FIQ,IRQ" bitfld.long 0x00 9. " IntSelect9 ,Interrupt Type Select Bit 9" "FIQ,IRQ" bitfld.long 0x00 8. " IntSelect8 ,Interrupt Type Select Bit 8" "FIQ,IRQ" textline " " bitfld.long 0x00 7. " IntSelect7 ,Interrupt Type Select Bit 7" "FIQ,IRQ" bitfld.long 0x00 6. " IntSelect6 ,Interrupt Type Select Bit 6" "FIQ,IRQ" bitfld.long 0x00 5. " IntSelect5 ,Interrupt Type Select Bit 5" "FIQ,IRQ" textline " " bitfld.long 0x00 4. " IntSelect4 ,Interrupt Type Select Bit 4" "FIQ,IRQ" bitfld.long 0x00 3. " IntSelect3 ,Interrupt Type Select Bit 3" "FIQ,IRQ" bitfld.long 0x00 2. " IntSelect2 ,Interrupt Type Select Bit 2" "FIQ,IRQ" textline " " bitfld.long 0x00 1. " IntSelect1 ,Interrupt Type Select Bit 1" "FIQ,IRQ" bitfld.long 0x00 0. " IntSelect0 ,Interrupt Type Select Bit 0" "FIQ,IRQ" line.long 0x04 "VIC1IntEnable,Interrupt Enable Register" bitfld.long 0x04 31. " IntEnable31 ,Interrupt Enable Bit 31" "Disabled,Enabled" bitfld.long 0x04 30. " IntEnable30 ,Interrupt Enable Bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " IntEnable29 ,Interrupt Enable Bit 29" "Disabled,Enabled" textline " " bitfld.long 0x04 28. " IntEnable28 ,Interrupt Enable Bit 28" "Disabled,Enabled" bitfld.long 0x04 27. " IntEnable27 ,Interrupt Enable Bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " IntEnable26 ,Interrupt Enable Bit 26" "Disabled,Enabled" textline " " bitfld.long 0x04 25. " IntEnable25 ,Interrupt Enable Bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " IntEnable24 ,Interrupt Enable Bit 24" "Disabled,Enabled" bitfld.long 0x04 23. " IntEnable23 ,Interrupt Enable Bit 23" "Disabled,Enabled" textline " " bitfld.long 0x04 22. " IntEnable22 ,Interrupt Enable Bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " IntEnable21 ,Interrupt Enable Bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " IntEnable20 ,Interrupt Enable Bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " IntEnable19 ,Interrupt Enable Bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " IntEnable18 ,Interrupt Enable Bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " IntEnable17 ,Interrupt Enable Bit 17" "Disabled,Enabled" textline " " bitfld.long 0x04 16. " IntEnable16 ,Interrupt Enable Bit 16" "Disabled,Enabled" bitfld.long 0x04 15. " IntEnable15 ,Interrupt Enable Bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " IntEnable14 ,Interrupt Enable Bit 14" "Disabled,Enabled" textline " " bitfld.long 0x04 13. " IntEnable13 ,Interrupt Enable Bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " IntEnable12 ,Interrupt Enable Bit 12" "Disabled,Enabled" bitfld.long 0x04 11. " IntEnable11 ,Interrupt Enable Bit 11" "Disabled,Enabled" textline " " bitfld.long 0x04 10. " IntEnable10 ,Interrupt Enable Bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " IntEnable9 ,Interrupt Enable Bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " IntEnable8 ,Interrupt Enable Bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " IntEnable7 ,Interrupt Enable Bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " IntEnable6 ,Interrupt Enable Bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " IntEnable5 ,Interrupt Enable Bit 5" "Disabled,Enabled" textline " " bitfld.long 0x04 4. " IntEnable4 ,Interrupt Enable Bit 4" "Disabled,Enabled" bitfld.long 0x04 3. " IntEnable3 ,Interrupt Enable Bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " IntEnable2 ,Interrupt Enable Bit 2" "Disabled,Enabled" textline " " bitfld.long 0x04 1. " IntEnable1 ,Interrupt Enable Bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " IntEnable0 ,Interrupt Enable Bit 0" "Disabled,Enabled" wgroup asd:0x0014++3 line.long 0x00 "VIC1IntEnClear,Interrupt Enable Clear Register" bitfld.long 0x00 31. " IntEnableClr31 ,Interrupt Enable Clear Bit 31" "No effect,Clear" bitfld.long 0x00 30. " IntEnableClr30 ,Interrupt Enable Clear Bit 30" "No effect,Clear" textline " " bitfld.long 0x00 29. " IntEnableClr29 ,Interrupt Enable Clear Bit 29" "No effect,Clear" bitfld.long 0x00 28. " IntEnableClr28 ,Interrupt Enable Clear Bit 28" "No effect,Clear" textline " " bitfld.long 0x00 27. " IntEnableClr27 ,Interrupt Enable Clear Bit 27" "No effect,Clear" bitfld.long 0x00 26. " IntEnableClr26 ,Interrupt Enable Clear Bit 26" "No effect,Clear" textline " " bitfld.long 0x00 25. " IntEnableClr25 ,Interrupt Enable Clear Bit 25" "No effect,Clear" bitfld.long 0x00 24. " IntEnableClr24 ,Interrupt Enable Clear Bit 24" "No effect,Clear" textline " " bitfld.long 0x00 23. " IntEnableClr23 ,Interrupt Enable Clear Bit 23" "No effect,Clear" bitfld.long 0x00 22. " IntEnableClr22 ,Interrupt Enable Clear Bit 22" "No effect,Clear" textline " " bitfld.long 0x00 21. " IntEnableClr21 ,Interrupt Enable Clear Bit 21" "No effect,Clear" bitfld.long 0x00 20. " IntEnableClr20 ,Interrupt Enable Clear Bit 20" "No effect,Clear" textline " " bitfld.long 0x00 19. " IntEnableClr19 ,Interrupt Enable Clear Bit 19" "No effect,Clear" bitfld.long 0x00 18. " IntEnableClr18 ,Interrupt Enable Clear Bit 18" "No effect,Clear" textline " " bitfld.long 0x00 17. " IntEnableClr17 ,Interrupt Enable Clear Bit 17" "No effect,Clear" bitfld.long 0x00 16. " IntEnableClr16 ,Interrupt Enable Clear Bit 16" "No effect,Clear" textline " " bitfld.long 0x00 15. " IntEnableClr15 ,Interrupt Enable Clear Bit 15" "No effect,Clear" bitfld.long 0x00 14. " IntEnableClr14 ,Interrupt Enable Clear Bit 14" "No effect,Clear" textline " " bitfld.long 0x00 13. " IntEnableClr13 ,Interrupt Enable Clear Bit 13" "No effect,Clear" bitfld.long 0x00 12. " IntEnableClr12 ,Interrupt Enable Clear Bit 12" "No effect,Clear" textline " " bitfld.long 0x00 11. " IntEnableClr11 ,Interrupt Enable Clear Bit 11" "No effect,Clear" bitfld.long 0x00 10. " IntEnableClr10 ,Interrupt Enable Clear Bit 10" "No effect,Clear" textline " " bitfld.long 0x00 9. " IntEnableClr9 ,Interrupt Enable Clear Bit 9" "No effect,Clear" bitfld.long 0x00 8. " IntEnableClr8 ,Interrupt Enable Clear Bit 8" "No effect,Clear" textline " " bitfld.long 0x00 7. " IntEnableClr7 ,Interrupt Enable Clear Bit 7" "No effect,Clear" bitfld.long 0x00 6. " IntEnableClr6 ,Interrupt Enable Clear Bit 6" "No effect,Clear" textline " " bitfld.long 0x00 5. " IntEnableClr5 ,Interrupt Enable Clear Bit 5" "No effect,Clear" bitfld.long 0x00 4. " IntEnableClr4 ,Interrupt Enable Clear Bit 4" "No effect,Clear" textline " " bitfld.long 0x00 3. " IntEnableClr3 ,Interrupt Enable Clear Bit 3" "No effect,Clear" bitfld.long 0x00 2. " IntEnableClr2 ,Interrupt Enable Clear Bit 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " IntEnableClr1 ,Interrupt Enable Clear Bit 1" "No effect,Clear" bitfld.long 0x00 0. " IntEnableClr0 ,Interrupt Enable Clear Bit 0" "No effect,Clear" group asd:0x0018++3 line.long 0x00 "VIC1SoftInt,Software Interrupt Register" bitfld.long 0x00 31. " SoftInt31 ,Software Interrupt Bit 31" "No effect,Generated" bitfld.long 0x00 30. " SoftInt30 ,Software Interrupt Bit 30" "No effect,Generated" textline " " bitfld.long 0x00 29. " SoftInt29 ,Software Interrupt Bit 29" "No effect,Generated" bitfld.long 0x00 28. " SoftInt28 ,Software Interrupt Bit 28" "No effect,Generated" textline " " bitfld.long 0x00 27. " SoftInt27 ,Software Interrupt Bit 27" "No effect,Generated" bitfld.long 0x00 26. " SoftInt26 ,Software Interrupt Bit 26" "No effect,Generated" textline " " bitfld.long 0x00 25. " SoftInt25 ,Software Interrupt Bit 25" "No effect,Generated" bitfld.long 0x00 24. " SoftInt24 ,Software Interrupt Bit 24" "No effect,Generated" textline " " bitfld.long 0x00 23. " SoftInt23 ,Software Interrupt Bit 23" "No effect,Generated" bitfld.long 0x00 22. " SoftInt22 ,Software Interrupt Bit 22" "No effect,Generated" textline " " bitfld.long 0x00 21. " SoftInt21 ,Software Interrupt Bit 21" "No effect,Generated" bitfld.long 0x00 20. " SoftInt20 ,Software Interrupt Bit 20" "No effect,Generated" textline " " bitfld.long 0x00 19. " SoftInt19 ,Software Interrupt Bit 19" "No effect,Generated" bitfld.long 0x00 18. " SoftInt18 ,Software Interrupt Bit 18" "No effect,Generated" textline " " bitfld.long 0x00 17. " SoftInt17 ,Software Interrupt Bit 17" "No effect,Generated" bitfld.long 0x00 16. " SoftInt16 ,Software Interrupt Bit 16" "No effect,Generated" textline " " bitfld.long 0x00 15. " SoftInt15 ,Software Interrupt Bit 15" "No effect,Generated" bitfld.long 0x00 14. " SoftInt14 ,Software Interrupt Bit 14" "No effect,Generated" textline " " bitfld.long 0x00 13. " SoftInt13 ,Software Interrupt Bit 13" "No effect,Generated" bitfld.long 0x00 12. " SoftInt12 ,Software Interrupt Bit 12" "No effect,Generated" textline " " bitfld.long 0x00 11. " SoftInt11 ,Software Interrupt Bit 11" "No effect,Generated" bitfld.long 0x00 10. " SoftInt10 ,Software Interrupt Bit 10" "No effect,Generated" textline " " bitfld.long 0x00 9. " SoftInt9 ,Software Interrupt Bit 9" "No effect,Generated" bitfld.long 0x00 8. " SoftInt8 ,Software Interrupt Bit 8" "No effect,Generated" textline " " bitfld.long 0x00 7. " SoftInt7 ,Software Interrupt Bit 7" "No effect,Generated" bitfld.long 0x00 6. " SoftInt6 ,Software Interrupt Bit 6" "No effect,Generated" textline " " bitfld.long 0x00 5. " SoftInt5 ,Software Interrupt Bit 5" "No effect,Generated" bitfld.long 0x00 4. " SoftInt4 ,Software Interrupt Bit 4" "No effect,Generated" textline " " bitfld.long 0x00 3. " SoftInt3 ,Software Interrupt Bit 3" "No effect,Generated" bitfld.long 0x00 2. " SoftInt2 ,Software Interrupt Bit 2" "No effect,Generated" textline " " bitfld.long 0x00 1. " SoftInt1 ,Software Interrupt Bit 1" "No effect,Generated" bitfld.long 0x00 0. " SoftInt0 ,Software Interrupt Bit 0" "No effect,Generated" wgroup asd:0x001C++3 line.long 0x00 "VIC1SoftIntClear,Software Interrupt Clear Register" bitfld.long 0x00 31. " SoftIntClr31 ,Software Interrupt Clear Bit 31" "No effect,Clear" bitfld.long 0x00 30. " SoftIntClr30 ,Software Interrupt Clear Bit 30" "No effect,Clear" textline " " bitfld.long 0x00 29. " SoftIntClr29 ,Software Interrupt Clear Bit 29" "No effect,Clear" bitfld.long 0x00 28. " SoftIntClr28 ,Software Interrupt Clear Bit 28" "No effect,Clear" textline " " bitfld.long 0x00 27. " SoftIntClr27 ,Software Interrupt Clear Bit 27" "No effect,Clear" bitfld.long 0x00 26. " SoftIntClr26 ,Software Interrupt Clear Bit 26" "No effect,Clear" textline " " bitfld.long 0x00 25. " SoftIntClr25 ,Software Interrupt Clear Bit 25" "No effect,Clear" bitfld.long 0x00 24. " SoftIntClr24 ,Software Interrupt Clear Bit 24" "No effect,Clear" textline " " bitfld.long 0x00 23. " SoftIntClr23 ,Software Interrupt Clear Bit 23" "No effect,Clear" bitfld.long 0x00 22. " SoftIntClr22 ,Software Interrupt Clear Bit 22" "No effect,Clear" textline " " bitfld.long 0x00 21. " SoftIntClr21 ,Software Interrupt Clear Bit 21" "No effect,Clear" bitfld.long 0x00 20. " SoftIntClr20 ,Software Interrupt Clear Bit 20" "No effect,Clear" textline " " bitfld.long 0x00 19. " SoftIntClr19 ,Software Interrupt Clear Bit 19" "No effect,Clear" bitfld.long 0x00 18. " SoftIntClr18 ,Software Interrupt Clear Bit 18" "No effect,Clear" textline " " bitfld.long 0x00 17. " SoftIntClr17 ,Software Interrupt Clear Bit 17" "No effect,Clear" bitfld.long 0x00 16. " SoftIntClr16 ,Software Interrupt Clear Bit 16" "No effect,Clear" textline " " bitfld.long 0x00 15. " SoftIntClr15 ,Software Interrupt Clear Bit 15" "No effect,Clear" bitfld.long 0x00 14. " SoftIntClr14 ,Software Interrupt Clear Bit 14" "No effect,Clear" textline " " bitfld.long 0x00 13. " SoftIntClr13 ,Software Interrupt Clear Bit 13" "No effect,Clear" bitfld.long 0x00 12. " SoftIntClr12 ,Software Interrupt Clear Bit 12" "No effect,Clear" textline " " bitfld.long 0x00 11. " SoftIntClr11 ,Software Interrupt Clear Bit 11" "No effect,Clear" bitfld.long 0x00 10. " SoftIntClr10 ,Software Interrupt Clear Bit 10" "No effect,Clear" textline " " bitfld.long 0x00 9. " SoftIntClr9 ,Software Interrupt Clear Bit 9" "No effect,Clear" bitfld.long 0x00 8. " SoftIntClr8 ,Software Interrupt Clear Bit 8" "No effect,Clear" textline " " bitfld.long 0x00 7. " SoftIntClr7 ,Software Interrupt Clear Bit 7" "No effect,Clear" bitfld.long 0x00 6. " SoftIntClr6 ,Software Interrupt Clear Bit 6" "No effect,Clear" textline " " bitfld.long 0x00 5. " SoftIntClr5 ,Software Interrupt Clear Bit 5" "No effect,Clear" bitfld.long 0x00 4. " SoftIntClr4 ,Software Interrupt Clear Bit 4" "No effect,Clear" textline " " bitfld.long 0x00 3. " SoftIntClr3 ,Software Interrupt Clear Bit 3" "No effect,Clear" bitfld.long 0x00 2. " SoftIntClr2 ,Software Interrupt Clear Bit 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " SoftIntClr1 ,Software Interrupt Clear Bit 1" "No effect,Clear" bitfld.long 0x00 0. " SoftIntClr0 ,Software Interrupt Clear Bit 0" "No effect,Clear" group asd:0x0020++3 line.long 0x00 "VIC1Protection,Protection Enable Register" bitfld.long 0x00 0. " Protection ,Protection Enable" "Disabled,Enabled" group asd:0x0030++7 line.long 0x00 "VIC1VectAddr,Vector Address Register" hexfld.long 0x00 " VectorAddr ,Vector Address Value" line.long 0x04 "VIC1DefVectAddr,Default Vector Address Register" hexfld.long 0x04 " DefVectorAddr ,Default Vector Address Value" ;end include file ep9312/interrupt/global.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0100 0 group asd:0x0100++3 line.long 0x00 "VIC1VectAddr0,Vector Address 0 Register" hexfld.long 0x00 " VectorAddr ,Vector 0 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0104 1 group asd:0x0104++3 line.long 0x00 "VIC1VectAddr1,Vector Address 1 Register" hexfld.long 0x00 " VectorAddr ,Vector 1 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0108 2 group asd:0x0108++3 line.long 0x00 "VIC1VectAddr2,Vector Address 2 Register" hexfld.long 0x00 " VectorAddr ,Vector 2 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x010C 3 group asd:0x010C++3 line.long 0x00 "VIC1VectAddr3,Vector Address 3 Register" hexfld.long 0x00 " VectorAddr ,Vector 3 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0110 4 group asd:0x0110++3 line.long 0x00 "VIC1VectAddr4,Vector Address 4 Register" hexfld.long 0x00 " VectorAddr ,Vector 4 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0114 5 group asd:0x0114++3 line.long 0x00 "VIC1VectAddr5,Vector Address 5 Register" hexfld.long 0x00 " VectorAddr ,Vector 5 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0118 6 group asd:0x0118++3 line.long 0x00 "VIC1VectAddr6,Vector Address 6 Register" hexfld.long 0x00 " VectorAddr ,Vector 6 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x011C 7 group asd:0x011C++3 line.long 0x00 "VIC1VectAddr7,Vector Address 7 Register" hexfld.long 0x00 " VectorAddr ,Vector 7 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0120 8 group asd:0x0120++3 line.long 0x00 "VIC1VectAddr8,Vector Address 8 Register" hexfld.long 0x00 " VectorAddr ,Vector 8 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0124 9 group asd:0x0124++3 line.long 0x00 "VIC1VectAddr9,Vector Address 9 Register" hexfld.long 0x00 " VectorAddr ,Vector 9 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0128 10 group asd:0x0128++3 line.long 0x00 "VIC1VectAddr10,Vector Address 10 Register" hexfld.long 0x00 " VectorAddr ,Vector 10 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x012C 11 group asd:0x012C++3 line.long 0x00 "VIC1VectAddr11,Vector Address 11 Register" hexfld.long 0x00 " VectorAddr ,Vector 11 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0130 12 group asd:0x0130++3 line.long 0x00 "VIC1VectAddr12,Vector Address 12 Register" hexfld.long 0x00 " VectorAddr ,Vector 12 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0134 13 group asd:0x0134++3 line.long 0x00 "VIC1VectAddr13,Vector Address 13 Register" hexfld.long 0x00 " VectorAddr ,Vector 13 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x0138 14 group asd:0x0138++3 line.long 0x00 "VIC1VectAddr14,Vector Address 14 Register" hexfld.long 0x00 " VectorAddr ,Vector 14 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 1 0x013C 15 group asd:0x013C++3 line.long 0x00 "VIC1VectAddr15,Vector Address 15 Register" hexfld.long 0x00 " VectorAddr ,Vector 15 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0200 0 group asd:0x0200++3 line.long 0x00 "VIC1VectCntrl0,Vector Control 0 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0204 1 group asd:0x0204++3 line.long 0x00 "VIC1VectCntrl1,Vector Control 1 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0208 2 group asd:0x0208++3 line.long 0x00 "VIC1VectCntrl2,Vector Control 2 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x020C 3 group asd:0x020C++3 line.long 0x00 "VIC1VectCntrl3,Vector Control 3 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0210 4 group asd:0x0210++3 line.long 0x00 "VIC1VectCntrl4,Vector Control 4 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0214 5 group asd:0x0214++3 line.long 0x00 "VIC1VectCntrl5,Vector Control 5 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0218 6 group asd:0x0218++3 line.long 0x00 "VIC1VectCntrl6,Vector Control 6 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x021C 7 group asd:0x021C++3 line.long 0x00 "VIC1VectCntrl7,Vector Control 7 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0220 8 group asd:0x0220++3 line.long 0x00 "VIC1VectCntrl8,Vector Control 8 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0224 9 group asd:0x0224++3 line.long 0x00 "VIC1VectCntrl9,Vector Control 9 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0228 10 group asd:0x0228++3 line.long 0x00 "VIC1VectCntrl10,Vector Control 10 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x022C 11 group asd:0x022C++3 line.long 0x00 "VIC1VectCntrl11,Vector Control 11 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0230 12 group asd:0x0230++3 line.long 0x00 "VIC1VectCntrl12,Vector Control 12 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0234 13 group asd:0x0234++3 line.long 0x00 "VIC1VectCntrl13,Vector Control 13 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x0238 14 group asd:0x0238++3 line.long 0x00 "VIC1VectCntrl14,Vector Control 14 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 1 0x023C 15 group asd:0x023C++3 line.long 0x00 "VIC1VectCntrl15,Vector Control 15 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/idreg.ph ;parameters: 1 rgroup asd:0xFE0++3 line.long 0x00 "VIC1PeriphID0,Peripherial Identification Register Bits [7:0] Register" rgroup asd:0xFE4++3 line.long 0x00 "VIC1PeriphID1,Peripherial Identification Register Bits [15:8] Register" rgroup asd:0xFE8++3 line.long 0x00 "VIC1PeriphID2,Peripherial Identification Register Bits [23:16] Register" rgroup asd:0xFEC++3 line.long 0x00 "VIC1PeriphID3,Peripherial Identification Register Bits [31:24] Register" ;end include file ep9312/interrupt/idreg.ph tree.end tree "Vector Interrupt Controller 2(VIC2)" base asd:0x800C0000 ;begin include file ep9312/interrupt/global.ph ;parameters: 2 rgroup asd:0x0000++0x0B line.long 0x00 "VIC2IRQStatus,IRQ Status Register" bitfld.long 0x00 31. " IRQStatus31 ,IRQ Interrupt Status Bit 31" "No interrupt,Interrupt" bitfld.long 0x00 30. " IRQStatus30 ,IRQ Interrupt Status Bit 30" "No interrupt,Interrupt" textline " " bitfld.long 0x00 29. " IRQStatus29 ,IRQ Interrupt Status Bit 29" "No interrupt,Interrupt" bitfld.long 0x00 28. " IRQStatus28 ,IRQ Interrupt Status Bit 28" "No interrupt,Interrupt" textline " " bitfld.long 0x00 27. " IRQStatus27 ,IRQ Interrupt Status Bit 27" "No interrupt,Interrupt" bitfld.long 0x00 26. " IRQStatus26 ,IRQ Interrupt Status Bit 26" "No interrupt,Interrupt" textline " " bitfld.long 0x00 25. " IRQStatus25 ,IRQ Interrupt Status Bit 25" "No interrupt,Interrupt" bitfld.long 0x00 24. " IRQStatus24 ,IRQ Interrupt Status Bit 24" "No interrupt,Interrupt" textline " " bitfld.long 0x00 23. " IRQStatus23 ,IRQ Interrupt Status Bit 23" "No interrupt,Interrupt" bitfld.long 0x00 22. " IRQStatus22 ,IRQ Interrupt Status Bit 22" "No interrupt,Interrupt" textline " " bitfld.long 0x00 21. " IRQStatus21 ,IRQ Interrupt Status Bit 21" "No interrupt,Interrupt" bitfld.long 0x00 20. " IRQStatus20 ,IRQ Interrupt Status Bit 20" "No interrupt,Interrupt" textline " " bitfld.long 0x00 19. " IRQStatus19 ,IRQ Interrupt Status Bit 19" "No interrupt,Interrupt" bitfld.long 0x00 18. " IRQStatus18 ,IRQ Interrupt Status Bit 18" "No interrupt,Interrupt" textline " " bitfld.long 0x00 17. " IRQStatus17 ,IRQ Interrupt Status Bit 17" "No interrupt,Interrupt" bitfld.long 0x00 16. " IRQStatus16 ,IRQ Interrupt Status Bit 16" "No interrupt,Interrupt" textline " " bitfld.long 0x00 15. " IRQStatus15 ,IRQ Interrupt Status Bit 15" "No interrupt,Interrupt" bitfld.long 0x00 14. " IRQStatus14 ,IRQ Interrupt Status Bit 14" "No interrupt,Interrupt" textline " " bitfld.long 0x00 13. " IRQStatus13 ,IRQ Interrupt Status Bit 13" "No interrupt,Interrupt" bitfld.long 0x00 12. " IRQStatus12 ,IRQ Interrupt Status Bit 12" "No interrupt,Interrupt" textline " " bitfld.long 0x00 11. " IRQStatus11 ,IRQ Interrupt Status Bit 11" "No interrupt,Interrupt" bitfld.long 0x00 10. " IRQStatus10 ,IRQ Interrupt Status Bit 10" "No interrupt,Interrupt" textline " " bitfld.long 0x00 9. " IRQStatus9 ,IRQ Interrupt Status Bit 9" "No interrupt,Interrupt" bitfld.long 0x00 8. " IRQStatus8 ,IRQ Interrupt Status Bit 8" "No interrupt,Interrupt" textline " " bitfld.long 0x00 7. " IRQStatus7 ,IRQ Interrupt Status Bit 7" "No interrupt,Interrupt" bitfld.long 0x00 6. " IRQStatus6 ,IRQ Interrupt Status Bit 6" "No interrupt,Interrupt" textline " " bitfld.long 0x00 5. " IRQStatus5 ,IRQ Interrupt Status Bit 5" "No interrupt,Interrupt" bitfld.long 0x00 4. " IRQStatus4 ,IRQ Interrupt Status Bit 4" "No interrupt,Interrupt" textline " " bitfld.long 0x00 3. " IRQStatus3 ,IRQ Interrupt Status Bit 3" "No interrupt,Interrupt" bitfld.long 0x00 2. " IRQStatus2 ,IRQ Interrupt Status Bit 2" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " IRQStatus1 ,IRQ Interrupt Status Bit 1" "No interrupt,Interrupt" bitfld.long 0x00 0. " IRQStatus0 ,IRQ Interrupt Status Bit 0" "No interrupt,Interrupt" line.long 0x04 "VIC2FIQStatus,FIQ Status Register" bitfld.long 0x04 31. " FIQStatus31 ,FIQ Interrupt Status Bit 31" "No interrupt,Interrupt" bitfld.long 0x04 30. " FIQStatus30 ,FIQ Interrupt Status Bit 30" "No interrupt,Interrupt" textline " " bitfld.long 0x04 29. " FIQStatus29 ,FIQ Interrupt Status Bit 29" "No interrupt,Interrupt" bitfld.long 0x04 28. " FIQStatus28 ,FIQ Interrupt Status Bit 28" "No interrupt,Interrupt" textline " " bitfld.long 0x04 27. " FIQStatus27 ,FIQ Interrupt Status Bit 27" "No interrupt,Interrupt" bitfld.long 0x04 26. " FIQStatus26 ,FIQ Interrupt Status Bit 26" "No interrupt,Interrupt" textline " " bitfld.long 0x04 25. " FIQStatus25 ,FIQ Interrupt Status Bit 25" "No interrupt,Interrupt" bitfld.long 0x04 24. " FIQStatus24 ,FIQ Interrupt Status Bit 24" "No interrupt,Interrupt" textline " " bitfld.long 0x04 23. " FIQStatus23 ,FIQ Interrupt Status Bit 23" "No interrupt,Interrupt" bitfld.long 0x04 22. " FIQStatus22 ,FIQ Interrupt Status Bit 22" "No interrupt,Interrupt" textline " " bitfld.long 0x04 21. " FIQStatus21 ,FIQ Interrupt Status Bit 21" "No interrupt,Interrupt" bitfld.long 0x04 20. " FIQStatus20 ,FIQ Interrupt Status Bit 20" "No interrupt,Interrupt" textline " " bitfld.long 0x04 19. " FIQStatus19 ,FIQ Interrupt Status Bit 19" "No interrupt,Interrupt" bitfld.long 0x04 18. " FIQStatus18 ,FIQ Interrupt Status Bit 18" "No interrupt,Interrupt" textline " " bitfld.long 0x04 17. " FIQStatus17 ,FIQ Interrupt Status Bit 17" "No interrupt,Interrupt" bitfld.long 0x04 16. " FIQStatus16 ,FIQ Interrupt Status Bit 16" "No interrupt,Interrupt" textline " " bitfld.long 0x04 15. " FIQStatus15 ,FIQ Interrupt Status Bit 15" "No interrupt,Interrupt" bitfld.long 0x04 14. " FIQStatus14 ,FIQ Interrupt Status Bit 14" "No interrupt,Interrupt" textline " " bitfld.long 0x04 13. " FIQStatus13 ,FIQ Interrupt Status Bit 13" "No interrupt,Interrupt" bitfld.long 0x04 12. " FIQStatus12 ,FIQ Interrupt Status Bit 12" "No interrupt,Interrupt" textline " " bitfld.long 0x04 11. " FIQStatus11 ,FIQ Interrupt Status Bit 11" "No interrupt,Interrupt" bitfld.long 0x04 10. " FIQStatus10 ,FIQ Interrupt Status Bit 10" "No interrupt,Interrupt" textline " " bitfld.long 0x04 9. " FIQStatus9 ,FIQ Interrupt Status Bit 9" "No interrupt,Interrupt" bitfld.long 0x04 8. " FIQStatus8 ,FIQ Interrupt Status Bit 8" "No interrupt,Interrupt" textline " " bitfld.long 0x04 7. " FIQStatus7 ,FIQ Interrupt Status Bit 7" "No interrupt,Interrupt" bitfld.long 0x04 6. " FIQStatus6 ,FIQ Interrupt Status Bit 6" "No interrupt,Interrupt" textline " " bitfld.long 0x04 5. " FIQStatus5 ,FIQ Interrupt Status Bit 5" "No interrupt,Interrupt" bitfld.long 0x04 4. " FIQStatus4 ,FIQ Interrupt Status Bit 4" "No interrupt,Interrupt" textline " " bitfld.long 0x04 3. " FIQStatus3 ,FIQ Interrupt Status Bit 3" "No interrupt,Interrupt" bitfld.long 0x04 2. " FIQStatus2 ,FIQ Interrupt Status Bit 2" "No interrupt,Interrupt" textline " " bitfld.long 0x04 1. " FIQStatus1 ,FIQ Interrupt Status Bit 1" "No interrupt,Interrupt" bitfld.long 0x04 0. " FIQStatus0 ,FIQ Interrupt Status Bit 0" "No interrupt,Interrupt" line.long 0x08 "VIC2RawIntr,Raw Interrupt Status Register" bitfld.long 0x08 31. " RawIntr31 ,Interrupt Status Bit 31 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 30. " RawIntr30 ,Interrupt Status Bit 30 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 29. " RawIntr29 ,Interrupt Status Bit 29 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 28. " RawIntr28 ,Interrupt Status Bit 28 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 27. " RawIntr27 ,Interrupt Status Bit 27 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 26. " RawIntr26 ,Interrupt Status Bit 26 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 25. " RawIntr25 ,Interrupt Status Bit 25 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 24. " RawIntr24 ,Interrupt Status Bit 24 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 23. " RawIntr23 ,Interrupt Status Bit 23 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 22. " RawIntr22 ,Interrupt Status Bit 22 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 21. " RawIntr21 ,Interrupt Status Bit 21 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 20. " RawIntr20 ,Interrupt Status Bit 20 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 19. " RawIntr19 ,Interrupt Status Bit 19 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 18. " RawIntr18 ,Interrupt Status Bit 18 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 17. " RawIntr17 ,Interrupt Status Bit 17 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 16. " RawIntr16 ,Interrupt Status Bit 16 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 15. " RawIntr15 ,Interrupt Status Bit 15 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 14. " RawIntr14 ,Interrupt Status Bit 14 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 13. " RawIntr13 ,Interrupt Status Bit 13 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 12. " RawIntr12 ,Interrupt Status Bit 12 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 11. " RawIntr11 ,Interrupt Status Bit 11 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 10. " RawIntr10 ,Interrupt Status Bit 10 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 9. " RawIntr9 ,Interrupt Status Bit 9 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 8. " RawIntr8 ,Interrupt Status Bit 8 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 7. " RawIntr7 ,Interrupt Status Bit 7 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 6. " RawIntr6 ,Interrupt Status Bit 6 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 5. " RawIntr5 ,Interrupt Status Bit 5 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 4. " RawIntr4 ,Interrupt Status Bit 4 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 3. " RawIntr3 ,Interrupt Status Bit 3 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 2. " RawIntr2 ,Interrupt Status Bit 2 without Masking" "No interrupt,Interrupt" textline " " bitfld.long 0x08 1. " RawIntr1 ,Interrupt Status Bit 1 without Masking" "No interrupt,Interrupt" bitfld.long 0x08 0. " RawIntr0 ,Interrupt Status Bit 0 without Masking" "No interrupt,Interrupt" group asd:0x000C++7 line.long 0x00 "VIC2IntSelect,Interrupt Select Register" bitfld.long 0x00 31. " IntSelect31 ,Interrupt Type Select Bit 31" "FIQ,IRQ" bitfld.long 0x00 30. " IntSelect30 ,Interrupt Type Select Bit 30" "FIQ,IRQ" bitfld.long 0x00 29. " IntSelect29 ,Interrupt Type Select Bit 29" "FIQ,IRQ" textline " " bitfld.long 0x00 28. " IntSelect28 ,Interrupt Type Select Bit 28" "FIQ,IRQ" bitfld.long 0x00 27. " IntSelect27 ,Interrupt Type Select Bit 27" "FIQ,IRQ" bitfld.long 0x00 26. " IntSelect26 ,Interrupt Type Select Bit 26" "FIQ,IRQ" textline " " bitfld.long 0x00 25. " IntSelect25 ,Interrupt Type Select Bit 25" "FIQ,IRQ" bitfld.long 0x00 24. " IntSelect24 ,Interrupt Type Select Bit 24" "FIQ,IRQ" bitfld.long 0x00 23. " IntSelect23 ,Interrupt Type Select Bit 23" "FIQ,IRQ" textline " " bitfld.long 0x00 22. " IntSelect22 ,Interrupt Type Select Bit 22" "FIQ,IRQ" bitfld.long 0x00 21. " IntSelect21 ,Interrupt Type Select Bit 21" "FIQ,IRQ" bitfld.long 0x00 20. " IntSelect20 ,Interrupt Type Select Bit 20" "FIQ,IRQ" textline " " bitfld.long 0x00 19. " IntSelect19 ,Interrupt Type Select Bit 19" "FIQ,IRQ" bitfld.long 0x00 18. " IntSelect18 ,Interrupt Type Select Bit 18" "FIQ,IRQ" bitfld.long 0x00 17. " IntSelect17 ,Interrupt Type Select Bit 17" "FIQ,IRQ" textline " " bitfld.long 0x00 16. " IntSelect16 ,Interrupt Type Select Bit 16" "FIQ,IRQ" bitfld.long 0x00 15. " IntSelect15 ,Interrupt Type Select Bit 15" "FIQ,IRQ" bitfld.long 0x00 14. " IntSelect14 ,Interrupt Type Select Bit 14" "FIQ,IRQ" textline " " bitfld.long 0x00 13. " IntSelect13 ,Interrupt Type Select Bit 13" "FIQ,IRQ" bitfld.long 0x00 12. " IntSelect12 ,Interrupt Type Select Bit 12" "FIQ,IRQ" bitfld.long 0x00 11. " IntSelect11 ,Interrupt Type Select Bit 11" "FIQ,IRQ" textline " " bitfld.long 0x00 10. " IntSelect10 ,Interrupt Type Select Bit 10" "FIQ,IRQ" bitfld.long 0x00 9. " IntSelect9 ,Interrupt Type Select Bit 9" "FIQ,IRQ" bitfld.long 0x00 8. " IntSelect8 ,Interrupt Type Select Bit 8" "FIQ,IRQ" textline " " bitfld.long 0x00 7. " IntSelect7 ,Interrupt Type Select Bit 7" "FIQ,IRQ" bitfld.long 0x00 6. " IntSelect6 ,Interrupt Type Select Bit 6" "FIQ,IRQ" bitfld.long 0x00 5. " IntSelect5 ,Interrupt Type Select Bit 5" "FIQ,IRQ" textline " " bitfld.long 0x00 4. " IntSelect4 ,Interrupt Type Select Bit 4" "FIQ,IRQ" bitfld.long 0x00 3. " IntSelect3 ,Interrupt Type Select Bit 3" "FIQ,IRQ" bitfld.long 0x00 2. " IntSelect2 ,Interrupt Type Select Bit 2" "FIQ,IRQ" textline " " bitfld.long 0x00 1. " IntSelect1 ,Interrupt Type Select Bit 1" "FIQ,IRQ" bitfld.long 0x00 0. " IntSelect0 ,Interrupt Type Select Bit 0" "FIQ,IRQ" line.long 0x04 "VIC2IntEnable,Interrupt Enable Register" bitfld.long 0x04 31. " IntEnable31 ,Interrupt Enable Bit 31" "Disabled,Enabled" bitfld.long 0x04 30. " IntEnable30 ,Interrupt Enable Bit 30" "Disabled,Enabled" bitfld.long 0x04 29. " IntEnable29 ,Interrupt Enable Bit 29" "Disabled,Enabled" textline " " bitfld.long 0x04 28. " IntEnable28 ,Interrupt Enable Bit 28" "Disabled,Enabled" bitfld.long 0x04 27. " IntEnable27 ,Interrupt Enable Bit 27" "Disabled,Enabled" bitfld.long 0x04 26. " IntEnable26 ,Interrupt Enable Bit 26" "Disabled,Enabled" textline " " bitfld.long 0x04 25. " IntEnable25 ,Interrupt Enable Bit 25" "Disabled,Enabled" bitfld.long 0x04 24. " IntEnable24 ,Interrupt Enable Bit 24" "Disabled,Enabled" bitfld.long 0x04 23. " IntEnable23 ,Interrupt Enable Bit 23" "Disabled,Enabled" textline " " bitfld.long 0x04 22. " IntEnable22 ,Interrupt Enable Bit 22" "Disabled,Enabled" bitfld.long 0x04 21. " IntEnable21 ,Interrupt Enable Bit 21" "Disabled,Enabled" bitfld.long 0x04 20. " IntEnable20 ,Interrupt Enable Bit 20" "Disabled,Enabled" textline " " bitfld.long 0x04 19. " IntEnable19 ,Interrupt Enable Bit 19" "Disabled,Enabled" bitfld.long 0x04 18. " IntEnable18 ,Interrupt Enable Bit 18" "Disabled,Enabled" bitfld.long 0x04 17. " IntEnable17 ,Interrupt Enable Bit 17" "Disabled,Enabled" textline " " bitfld.long 0x04 16. " IntEnable16 ,Interrupt Enable Bit 16" "Disabled,Enabled" bitfld.long 0x04 15. " IntEnable15 ,Interrupt Enable Bit 15" "Disabled,Enabled" bitfld.long 0x04 14. " IntEnable14 ,Interrupt Enable Bit 14" "Disabled,Enabled" textline " " bitfld.long 0x04 13. " IntEnable13 ,Interrupt Enable Bit 13" "Disabled,Enabled" bitfld.long 0x04 12. " IntEnable12 ,Interrupt Enable Bit 12" "Disabled,Enabled" bitfld.long 0x04 11. " IntEnable11 ,Interrupt Enable Bit 11" "Disabled,Enabled" textline " " bitfld.long 0x04 10. " IntEnable10 ,Interrupt Enable Bit 10" "Disabled,Enabled" bitfld.long 0x04 9. " IntEnable9 ,Interrupt Enable Bit 9" "Disabled,Enabled" bitfld.long 0x04 8. " IntEnable8 ,Interrupt Enable Bit 8" "Disabled,Enabled" textline " " bitfld.long 0x04 7. " IntEnable7 ,Interrupt Enable Bit 7" "Disabled,Enabled" bitfld.long 0x04 6. " IntEnable6 ,Interrupt Enable Bit 6" "Disabled,Enabled" bitfld.long 0x04 5. " IntEnable5 ,Interrupt Enable Bit 5" "Disabled,Enabled" textline " " bitfld.long 0x04 4. " IntEnable4 ,Interrupt Enable Bit 4" "Disabled,Enabled" bitfld.long 0x04 3. " IntEnable3 ,Interrupt Enable Bit 3" "Disabled,Enabled" bitfld.long 0x04 2. " IntEnable2 ,Interrupt Enable Bit 2" "Disabled,Enabled" textline " " bitfld.long 0x04 1. " IntEnable1 ,Interrupt Enable Bit 1" "Disabled,Enabled" bitfld.long 0x04 0. " IntEnable0 ,Interrupt Enable Bit 0" "Disabled,Enabled" wgroup asd:0x0014++3 line.long 0x00 "VIC2IntEnClear,Interrupt Enable Clear Register" bitfld.long 0x00 31. " IntEnableClr31 ,Interrupt Enable Clear Bit 31" "No effect,Clear" bitfld.long 0x00 30. " IntEnableClr30 ,Interrupt Enable Clear Bit 30" "No effect,Clear" textline " " bitfld.long 0x00 29. " IntEnableClr29 ,Interrupt Enable Clear Bit 29" "No effect,Clear" bitfld.long 0x00 28. " IntEnableClr28 ,Interrupt Enable Clear Bit 28" "No effect,Clear" textline " " bitfld.long 0x00 27. " IntEnableClr27 ,Interrupt Enable Clear Bit 27" "No effect,Clear" bitfld.long 0x00 26. " IntEnableClr26 ,Interrupt Enable Clear Bit 26" "No effect,Clear" textline " " bitfld.long 0x00 25. " IntEnableClr25 ,Interrupt Enable Clear Bit 25" "No effect,Clear" bitfld.long 0x00 24. " IntEnableClr24 ,Interrupt Enable Clear Bit 24" "No effect,Clear" textline " " bitfld.long 0x00 23. " IntEnableClr23 ,Interrupt Enable Clear Bit 23" "No effect,Clear" bitfld.long 0x00 22. " IntEnableClr22 ,Interrupt Enable Clear Bit 22" "No effect,Clear" textline " " bitfld.long 0x00 21. " IntEnableClr21 ,Interrupt Enable Clear Bit 21" "No effect,Clear" bitfld.long 0x00 20. " IntEnableClr20 ,Interrupt Enable Clear Bit 20" "No effect,Clear" textline " " bitfld.long 0x00 19. " IntEnableClr19 ,Interrupt Enable Clear Bit 19" "No effect,Clear" bitfld.long 0x00 18. " IntEnableClr18 ,Interrupt Enable Clear Bit 18" "No effect,Clear" textline " " bitfld.long 0x00 17. " IntEnableClr17 ,Interrupt Enable Clear Bit 17" "No effect,Clear" bitfld.long 0x00 16. " IntEnableClr16 ,Interrupt Enable Clear Bit 16" "No effect,Clear" textline " " bitfld.long 0x00 15. " IntEnableClr15 ,Interrupt Enable Clear Bit 15" "No effect,Clear" bitfld.long 0x00 14. " IntEnableClr14 ,Interrupt Enable Clear Bit 14" "No effect,Clear" textline " " bitfld.long 0x00 13. " IntEnableClr13 ,Interrupt Enable Clear Bit 13" "No effect,Clear" bitfld.long 0x00 12. " IntEnableClr12 ,Interrupt Enable Clear Bit 12" "No effect,Clear" textline " " bitfld.long 0x00 11. " IntEnableClr11 ,Interrupt Enable Clear Bit 11" "No effect,Clear" bitfld.long 0x00 10. " IntEnableClr10 ,Interrupt Enable Clear Bit 10" "No effect,Clear" textline " " bitfld.long 0x00 9. " IntEnableClr9 ,Interrupt Enable Clear Bit 9" "No effect,Clear" bitfld.long 0x00 8. " IntEnableClr8 ,Interrupt Enable Clear Bit 8" "No effect,Clear" textline " " bitfld.long 0x00 7. " IntEnableClr7 ,Interrupt Enable Clear Bit 7" "No effect,Clear" bitfld.long 0x00 6. " IntEnableClr6 ,Interrupt Enable Clear Bit 6" "No effect,Clear" textline " " bitfld.long 0x00 5. " IntEnableClr5 ,Interrupt Enable Clear Bit 5" "No effect,Clear" bitfld.long 0x00 4. " IntEnableClr4 ,Interrupt Enable Clear Bit 4" "No effect,Clear" textline " " bitfld.long 0x00 3. " IntEnableClr3 ,Interrupt Enable Clear Bit 3" "No effect,Clear" bitfld.long 0x00 2. " IntEnableClr2 ,Interrupt Enable Clear Bit 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " IntEnableClr1 ,Interrupt Enable Clear Bit 1" "No effect,Clear" bitfld.long 0x00 0. " IntEnableClr0 ,Interrupt Enable Clear Bit 0" "No effect,Clear" group asd:0x0018++3 line.long 0x00 "VIC2SoftInt,Software Interrupt Register" bitfld.long 0x00 31. " SoftInt31 ,Software Interrupt Bit 31" "No effect,Generated" bitfld.long 0x00 30. " SoftInt30 ,Software Interrupt Bit 30" "No effect,Generated" textline " " bitfld.long 0x00 29. " SoftInt29 ,Software Interrupt Bit 29" "No effect,Generated" bitfld.long 0x00 28. " SoftInt28 ,Software Interrupt Bit 28" "No effect,Generated" textline " " bitfld.long 0x00 27. " SoftInt27 ,Software Interrupt Bit 27" "No effect,Generated" bitfld.long 0x00 26. " SoftInt26 ,Software Interrupt Bit 26" "No effect,Generated" textline " " bitfld.long 0x00 25. " SoftInt25 ,Software Interrupt Bit 25" "No effect,Generated" bitfld.long 0x00 24. " SoftInt24 ,Software Interrupt Bit 24" "No effect,Generated" textline " " bitfld.long 0x00 23. " SoftInt23 ,Software Interrupt Bit 23" "No effect,Generated" bitfld.long 0x00 22. " SoftInt22 ,Software Interrupt Bit 22" "No effect,Generated" textline " " bitfld.long 0x00 21. " SoftInt21 ,Software Interrupt Bit 21" "No effect,Generated" bitfld.long 0x00 20. " SoftInt20 ,Software Interrupt Bit 20" "No effect,Generated" textline " " bitfld.long 0x00 19. " SoftInt19 ,Software Interrupt Bit 19" "No effect,Generated" bitfld.long 0x00 18. " SoftInt18 ,Software Interrupt Bit 18" "No effect,Generated" textline " " bitfld.long 0x00 17. " SoftInt17 ,Software Interrupt Bit 17" "No effect,Generated" bitfld.long 0x00 16. " SoftInt16 ,Software Interrupt Bit 16" "No effect,Generated" textline " " bitfld.long 0x00 15. " SoftInt15 ,Software Interrupt Bit 15" "No effect,Generated" bitfld.long 0x00 14. " SoftInt14 ,Software Interrupt Bit 14" "No effect,Generated" textline " " bitfld.long 0x00 13. " SoftInt13 ,Software Interrupt Bit 13" "No effect,Generated" bitfld.long 0x00 12. " SoftInt12 ,Software Interrupt Bit 12" "No effect,Generated" textline " " bitfld.long 0x00 11. " SoftInt11 ,Software Interrupt Bit 11" "No effect,Generated" bitfld.long 0x00 10. " SoftInt10 ,Software Interrupt Bit 10" "No effect,Generated" textline " " bitfld.long 0x00 9. " SoftInt9 ,Software Interrupt Bit 9" "No effect,Generated" bitfld.long 0x00 8. " SoftInt8 ,Software Interrupt Bit 8" "No effect,Generated" textline " " bitfld.long 0x00 7. " SoftInt7 ,Software Interrupt Bit 7" "No effect,Generated" bitfld.long 0x00 6. " SoftInt6 ,Software Interrupt Bit 6" "No effect,Generated" textline " " bitfld.long 0x00 5. " SoftInt5 ,Software Interrupt Bit 5" "No effect,Generated" bitfld.long 0x00 4. " SoftInt4 ,Software Interrupt Bit 4" "No effect,Generated" textline " " bitfld.long 0x00 3. " SoftInt3 ,Software Interrupt Bit 3" "No effect,Generated" bitfld.long 0x00 2. " SoftInt2 ,Software Interrupt Bit 2" "No effect,Generated" textline " " bitfld.long 0x00 1. " SoftInt1 ,Software Interrupt Bit 1" "No effect,Generated" bitfld.long 0x00 0. " SoftInt0 ,Software Interrupt Bit 0" "No effect,Generated" wgroup asd:0x001C++3 line.long 0x00 "VIC2SoftIntClear,Software Interrupt Clear Register" bitfld.long 0x00 31. " SoftIntClr31 ,Software Interrupt Clear Bit 31" "No effect,Clear" bitfld.long 0x00 30. " SoftIntClr30 ,Software Interrupt Clear Bit 30" "No effect,Clear" textline " " bitfld.long 0x00 29. " SoftIntClr29 ,Software Interrupt Clear Bit 29" "No effect,Clear" bitfld.long 0x00 28. " SoftIntClr28 ,Software Interrupt Clear Bit 28" "No effect,Clear" textline " " bitfld.long 0x00 27. " SoftIntClr27 ,Software Interrupt Clear Bit 27" "No effect,Clear" bitfld.long 0x00 26. " SoftIntClr26 ,Software Interrupt Clear Bit 26" "No effect,Clear" textline " " bitfld.long 0x00 25. " SoftIntClr25 ,Software Interrupt Clear Bit 25" "No effect,Clear" bitfld.long 0x00 24. " SoftIntClr24 ,Software Interrupt Clear Bit 24" "No effect,Clear" textline " " bitfld.long 0x00 23. " SoftIntClr23 ,Software Interrupt Clear Bit 23" "No effect,Clear" bitfld.long 0x00 22. " SoftIntClr22 ,Software Interrupt Clear Bit 22" "No effect,Clear" textline " " bitfld.long 0x00 21. " SoftIntClr21 ,Software Interrupt Clear Bit 21" "No effect,Clear" bitfld.long 0x00 20. " SoftIntClr20 ,Software Interrupt Clear Bit 20" "No effect,Clear" textline " " bitfld.long 0x00 19. " SoftIntClr19 ,Software Interrupt Clear Bit 19" "No effect,Clear" bitfld.long 0x00 18. " SoftIntClr18 ,Software Interrupt Clear Bit 18" "No effect,Clear" textline " " bitfld.long 0x00 17. " SoftIntClr17 ,Software Interrupt Clear Bit 17" "No effect,Clear" bitfld.long 0x00 16. " SoftIntClr16 ,Software Interrupt Clear Bit 16" "No effect,Clear" textline " " bitfld.long 0x00 15. " SoftIntClr15 ,Software Interrupt Clear Bit 15" "No effect,Clear" bitfld.long 0x00 14. " SoftIntClr14 ,Software Interrupt Clear Bit 14" "No effect,Clear" textline " " bitfld.long 0x00 13. " SoftIntClr13 ,Software Interrupt Clear Bit 13" "No effect,Clear" bitfld.long 0x00 12. " SoftIntClr12 ,Software Interrupt Clear Bit 12" "No effect,Clear" textline " " bitfld.long 0x00 11. " SoftIntClr11 ,Software Interrupt Clear Bit 11" "No effect,Clear" bitfld.long 0x00 10. " SoftIntClr10 ,Software Interrupt Clear Bit 10" "No effect,Clear" textline " " bitfld.long 0x00 9. " SoftIntClr9 ,Software Interrupt Clear Bit 9" "No effect,Clear" bitfld.long 0x00 8. " SoftIntClr8 ,Software Interrupt Clear Bit 8" "No effect,Clear" textline " " bitfld.long 0x00 7. " SoftIntClr7 ,Software Interrupt Clear Bit 7" "No effect,Clear" bitfld.long 0x00 6. " SoftIntClr6 ,Software Interrupt Clear Bit 6" "No effect,Clear" textline " " bitfld.long 0x00 5. " SoftIntClr5 ,Software Interrupt Clear Bit 5" "No effect,Clear" bitfld.long 0x00 4. " SoftIntClr4 ,Software Interrupt Clear Bit 4" "No effect,Clear" textline " " bitfld.long 0x00 3. " SoftIntClr3 ,Software Interrupt Clear Bit 3" "No effect,Clear" bitfld.long 0x00 2. " SoftIntClr2 ,Software Interrupt Clear Bit 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " SoftIntClr1 ,Software Interrupt Clear Bit 1" "No effect,Clear" bitfld.long 0x00 0. " SoftIntClr0 ,Software Interrupt Clear Bit 0" "No effect,Clear" group asd:0x0020++3 line.long 0x00 "VIC2Protection,Protection Enable Register" bitfld.long 0x00 0. " Protection ,Protection Enable" "Disabled,Enabled" group asd:0x0030++7 line.long 0x00 "VIC2VectAddr,Vector Address Register" hexfld.long 0x00 " VectorAddr ,Vector Address Value" line.long 0x04 "VIC2DefVectAddr,Default Vector Address Register" hexfld.long 0x04 " DefVectorAddr ,Default Vector Address Value" ;end include file ep9312/interrupt/global.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0100 0 group asd:0x0100++3 line.long 0x00 "VIC2VectAddr0,Vector Address 0 Register" hexfld.long 0x00 " VectorAddr ,Vector 0 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0104 1 group asd:0x0104++3 line.long 0x00 "VIC2VectAddr1,Vector Address 1 Register" hexfld.long 0x00 " VectorAddr ,Vector 1 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0108 2 group asd:0x0108++3 line.long 0x00 "VIC2VectAddr2,Vector Address 2 Register" hexfld.long 0x00 " VectorAddr ,Vector 2 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x010C 3 group asd:0x010C++3 line.long 0x00 "VIC2VectAddr3,Vector Address 3 Register" hexfld.long 0x00 " VectorAddr ,Vector 3 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0110 4 group asd:0x0110++3 line.long 0x00 "VIC2VectAddr4,Vector Address 4 Register" hexfld.long 0x00 " VectorAddr ,Vector 4 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0114 5 group asd:0x0114++3 line.long 0x00 "VIC2VectAddr5,Vector Address 5 Register" hexfld.long 0x00 " VectorAddr ,Vector 5 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0118 6 group asd:0x0118++3 line.long 0x00 "VIC2VectAddr6,Vector Address 6 Register" hexfld.long 0x00 " VectorAddr ,Vector 6 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x011C 7 group asd:0x011C++3 line.long 0x00 "VIC2VectAddr7,Vector Address 7 Register" hexfld.long 0x00 " VectorAddr ,Vector 7 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0120 8 group asd:0x0120++3 line.long 0x00 "VIC2VectAddr8,Vector Address 8 Register" hexfld.long 0x00 " VectorAddr ,Vector 8 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0124 9 group asd:0x0124++3 line.long 0x00 "VIC2VectAddr9,Vector Address 9 Register" hexfld.long 0x00 " VectorAddr ,Vector 9 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0128 10 group asd:0x0128++3 line.long 0x00 "VIC2VectAddr10,Vector Address 10 Register" hexfld.long 0x00 " VectorAddr ,Vector 10 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x012C 11 group asd:0x012C++3 line.long 0x00 "VIC2VectAddr11,Vector Address 11 Register" hexfld.long 0x00 " VectorAddr ,Vector 11 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0130 12 group asd:0x0130++3 line.long 0x00 "VIC2VectAddr12,Vector Address 12 Register" hexfld.long 0x00 " VectorAddr ,Vector 12 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0134 13 group asd:0x0134++3 line.long 0x00 "VIC2VectAddr13,Vector Address 13 Register" hexfld.long 0x00 " VectorAddr ,Vector 13 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x0138 14 group asd:0x0138++3 line.long 0x00 "VIC2VectAddr14,Vector Address 14 Register" hexfld.long 0x00 " VectorAddr ,Vector 14 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vector.ph ;parameters: 2 0x013C 15 group asd:0x013C++3 line.long 0x00 "VIC2VectAddr15,Vector Address 15 Register" hexfld.long 0x00 " VectorAddr ,Vector 15 Address Register" ;end include file ep9312/interrupt/vector.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0200 0 group asd:0x0200++3 line.long 0x00 "VIC2VectCntrl0,Vector Control 0 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0204 1 group asd:0x0204++3 line.long 0x00 "VIC2VectCntrl1,Vector Control 1 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0208 2 group asd:0x0208++3 line.long 0x00 "VIC2VectCntrl2,Vector Control 2 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x020C 3 group asd:0x020C++3 line.long 0x00 "VIC2VectCntrl3,Vector Control 3 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0210 4 group asd:0x0210++3 line.long 0x00 "VIC2VectCntrl4,Vector Control 4 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0214 5 group asd:0x0214++3 line.long 0x00 "VIC2VectCntrl5,Vector Control 5 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0218 6 group asd:0x0218++3 line.long 0x00 "VIC2VectCntrl6,Vector Control 6 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x021C 7 group asd:0x021C++3 line.long 0x00 "VIC2VectCntrl7,Vector Control 7 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0220 8 group asd:0x0220++3 line.long 0x00 "VIC2VectCntrl8,Vector Control 8 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0224 9 group asd:0x0224++3 line.long 0x00 "VIC2VectCntrl9,Vector Control 9 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0228 10 group asd:0x0228++3 line.long 0x00 "VIC2VectCntrl10,Vector Control 10 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x022C 11 group asd:0x022C++3 line.long 0x00 "VIC2VectCntrl11,Vector Control 11 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0230 12 group asd:0x0230++3 line.long 0x00 "VIC2VectCntrl12,Vector Control 12 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0234 13 group asd:0x0234++3 line.long 0x00 "VIC2VectCntrl13,Vector Control 13 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x0238 14 group asd:0x0238++3 line.long 0x00 "VIC2VectCntrl14,Vector Control 14 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/vectctrl.ph ;parameters: 2 0x023C 15 group asd:0x023C++3 line.long 0x00 "VIC2VectCntrl15,Vector Control 15 Register" bitfld.long 0x00 5. " E ,Interrupt Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--4. 1. " IntSource ,Interrupt Source" ;end include file ep9312/interrupt/vectctrl.ph ;begin include file ep9312/interrupt/idreg.ph ;parameters: 2 rgroup asd:0xFE0++3 line.long 0x00 "VIC2PeriphID0,Peripherial Identification Register Bits [7:0] Register" rgroup asd:0xFE4++3 line.long 0x00 "VIC2PeriphID1,Peripherial Identification Register Bits [15:8] Register" rgroup asd:0xFE8++3 line.long 0x00 "VIC2PeriphID2,Peripherial Identification Register Bits [23:16] Register" rgroup asd:0xFEC++3 line.long 0x00 "VIC2PeriphID3,Peripherial Identification Register Bits [31:24] Register" ;end include file ep9312/interrupt/idreg.ph tree.end width 16. 8. ;end include file ep9312/interrupt.ph tree.end tree "Raster Engine with Analog/LCD Timing and Interface" base asd:0x80030000 ;begin include file ep9312/raster.ph ;parameters: base asd:0x80030000 ;begin include file ep9312/raster/rasterengine.ph ;parameters: width 18. 8. group asd:0x0000++0x0B line.long 0x00 "VLinesTotal,Total Number of Vertical Frame Lines Register" hexmask.long.word 0x00 0.--10. 1. " TOTAL ,Total Number of Vertical Frame Lines" line.long 0x04 "VSyncStrtStop,Vertical Sync Pulse Setup Register" hexmask.long.word 0x04 16.--26. 1. " STOP ,Value for N_VSYNC Signal to Become Inactive" hexmask.long.word 0x04 0.--10. 1. " STRT ,Value for N_VSYNC Signal to Become Active" line.long 0x08 "VActiveStrtStop,Vertical Active Setup Register" hexmask.long.word 0x08 16.--26. 1. " STOP ,Vertical Down Counter at wchich VACTIVE Signal Becomes Inactive" hexmask.long.word 0x08 0.--10. 1. " STRT ,Vertical Down Counter at wchich VACTIVE Signal Becomes Active" group asd:0x0228++3 line.long 0x00 "VBlankStrtStop,Vertical Blanking Setup Register" hexmask.long.word 0x00 16.--26. 1. " STOP ,Value when N_VBLANK Signal Becomes Active" hexmask.long.word 0x00 0.--10. 1. " STRT ,Value when N_VBLANK Signal Becomes Inactive" group asd:0x000C++0x0F line.long 0x00 "VClkStrtStop,Vertical Clock Active Frame Register" hexmask.long.word 0x00 16.--26. 1. " STOP ,Value when VCLKEN Signal Becomes Active" hexmask.long.word 0x00 0.--10. 1. " STRT ,Value when VCLKEN Signal Becomes Inactive" line.long 0x04 "HClkTotal,Total Number of Horizontal Line Clocks Register" hexmask.long.word 0x04 0.--10. 1. " TOTAL ,Total Number of Horizontal Line Clocks" line.long 0x08 "HSyncStrtStop,Horizontal Sync Pulse Setup Register" hexmask.long.word 0x08 16.--26. 1. " STOP ,Value for N_HSYNC Signal to Become Inactive" hexmask.long.word 0x08 0.--10. 1. " STRT ,Value for N_HSYNC Signal to Become Active" line.long 0x0C "HActiveStrtStop,Horizontal Active Setup Register" hexmask.long.word 0x0C 16.--26. 1. " STOP ,Vertical Down Counter at wchich HACTIVE Signal Becomes Inactive" hexmask.long.word 0x0C 0.--10. 1. " STRT ,Vertical Down Counter at wchich HACTIVE Signal Becomes Active" group asd:0x022C++3 line.long 0x00 "HBlankStrtStop,Horizontal Blanking Setup Register" hexmask.long.word 0x00 16.--26. 1. " STOP ,Value when N_HBLANK Signal Becomes Active" hexmask.long.word 0x00 0.--10. 1. " STRT ,Value when N_HBLANK Signal Becomes Inactive" group asd:0x001C++3 line.long 0x00 "HClkStrtStop,Horizontal Clock Active Frame Register" hexmask.long.word 0x00 16.--26. 1. " STOP ,Value when HCLKEN Signal Becomes Active" hexmask.long.word 0x00 0.--10. 1. " STRT ,Value when HCLKEN Signal Becomes Inactive" group asd:0x0020++0x1F line.long 0x00 "Brightness,PWM Brightness Control Register" hexmask.long.byte 0x00 8.--15. 1. " CMP ,Brightness Control Duty Cycle" hexmask.long.byte 0x00 0.--7. 1. " CNT ,Horizontal Lines Counted During Brightness Waveform Period" line.long 0x04 "VideoAttribs,Video State Machine Parameters Register" bitfld.long 0x04 21.--22. " SDSEL ,Video Buffer SDRAM Selector" "SDCSn[0],SDCSn[1],SDCSn[2],SDCSn[3]" bitfld.long 0x04 20. " BKPXD ,Blank Pixel Data" "No blanked,Blanked" textline " " bitfld.long 0x04 19. " DVERT ,Double Vertical Counter Base" "Normal,Double" bitfld.long 0x04 18. " DHORZ ,Double Horizontal Counter Base" "Normal,Double" textline " " bitfld.long 0x04 17. " EQUSER ,Equalization/Serration Bit" "No inserting,Inserting" bitfld.long 0x04 16. " INTRLC ,Interlaced Bit" "Normal,Interlaced mode" textline " " bitfld.long 0x04 15. " INT ,Interrupt Status Bit" "No interrupt,Interrupt" bitfld.long 0x04 14. " INTEN ,Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 13. " PIFEN ,Parallel Interface Enable Bit" "Disabled,Enabled" bitfld.long 0x04 12. " CCIREN ,Digital Video Output Signals Enable Control" "Disabled,Enabled" textline " " bitfld.long 0x04 10. " LCDEN ,LCD XECL and YSCL Enable" "Disabled,Enabled" bitfld.long 0x04 9. " ACEN ,LCD AC Wave Form Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 8. " INVCLK ,Invert Pixel Clock" "Rising edge,Falling edge" bitfld.long 0x04 7. " BLKPOL ,Blank Signal Output POlarity" "Low,High" textline " " bitfld.long 0x04 6. " HSPOL ,Horizontal Sync Signal Output Polarity" "Low,High" bitfld.long 0x04 5. " V/CPOL ,Vertica/Composite Sync Signal Output Polarity" "Active low,Active high" textline " " bitfld.long 0x04 4. " CSYNC ,Generate Composite Sync Signal on V/Csync Output" "Vertical,Composite" bitfld.long 0x04 3. " DATEN ,Enable Video Pixel Data Outputs" "Disabled,Enabled" textline " " bitfld.long 0x04 2. " SYNCEN ,Enable Video Sync Outputs" "Disabled,Enabled" bitfld.long 0x04 1. " PCLKEN ,ENable Video Pixel Clock Output" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " EN ,Enable Video State Machine" "Disabled,Enabled" line.long 0x08 "VidScrnPage,Starting Address of Video Screen Register" hexmask.long.long 0x08 2.--27. 1. " PAGE ,Video Screen Page Starting SDRAM Address" line.long 0x0C "VidScrnHPage,Starting Address of Video Screen Half Page" hexmask.long.long 0x0C 2.--27. 1. " PAGE ,Video Screen Half Page Starting SDRAM Address" line.long 0x10 "ScrnLines,Number of Active Lines Scanned to the Screen Register" hexmask.long.word 0x10 0.--10. 1. " LINES ,Number of Active Lines Scanned to the Screen" line.long 0x14 "LineLength,Length in Words of Data for Lines Register" hexmask.long.word 0x14 0.--10. 1. " LEN ,Length in Words of Data for Lines" line.long 0x18 "VLineStep,Memory Step for Each Line Register" hexmask.long.long 0x18 0.--11. 1. " STEP ,Line Step Added to Address For Every Video Line Scanned to Display" line.long 0x1C "LineCarry,Horizontal/Vertical Offset Parameter Register" hexmask.long.word 0x1C 0.--10. 1. " LCARY ,Horizontal/Vertical Offset Parameter" group asd:0x0040++0x0F line.long 0x00 "BlinkRate,Blink Couter Setup Register" hexmask.long.byte 0x00 0.--7. 1. " RATE ,Blinking Rate" line.long 0x04 "BlinkMask,Logic Mask Applied to Pixel to Perform Blink Operation Register" hexmask.long.tbyte 0x04 0.--23. 1. " MASK ,Blink Mask" line.long 0x08 "BlinkPattern,Compare Value for Determining Blinking Pixels Register" hexmask.long.tbyte 0x08 0.--23. 1. " PATRN ,Blink Pattern" line.long 0x0C "PattrnMask,Mask to Limit Pattern Register" bitfld.long 0x0C 23. " PMASK23 ,Pattern Mask Bit 23" "Not used,Used" bitfld.long 0x0C 22. " PMASK22 ,Pattern Mask Bit 22" "Not used,Used" textline " " bitfld.long 0x0C 21. " PMASK21 ,Pattern Mask Bit 21" "Not used,Used" bitfld.long 0x0C 20. " PMASK20 ,Pattern Mask Bit 20" "Not used,Used" textline " " bitfld.long 0x0C 19. " PMASK19 ,Pattern Mask Bit 19" "Not used,Used" bitfld.long 0x0C 18. " PMASK18 ,Pattern Mask Bit 18" "Not used,Used" textline " " bitfld.long 0x0C 17. " PMASK17 ,Pattern Mask Bit 17" "Not used,Used" bitfld.long 0x0C 16. " PMASK16 ,Pattern Mask Bit 16" "Not used,Used" textline " " bitfld.long 0x0C 15. " PMASK15 ,Pattern Mask Bit 15" "Not used,Used" bitfld.long 0x0C 14. " PMASK14 ,Pattern Mask Bit 14" "Not used,Used" textline " " bitfld.long 0x0C 13. " PMASK13 ,Pattern Mask Bit 13" "Not used,Used" bitfld.long 0x0C 12. " PMASK12 ,Pattern Mask Bit 12" "Not used,Used" textline " " bitfld.long 0x0C 11. " PMASK11 ,Pattern Mask Bit 11" "Not used,Used" bitfld.long 0x0C 10. " PMASK10 ,Pattern Mask Bit 10" "Not used,Used" textline " " bitfld.long 0x0C 9. " PMASK9 ,Pattern Mask Bit 9" "Not used,Used" bitfld.long 0x0C 8. " PMASK8 ,Pattern Mask Bit 8" "Not used,Used" textline " " bitfld.long 0x0C 7. " PMASK7 ,Pattern Mask Bit 7" "Not used,Used" bitfld.long 0x0C 6. " PMASK6 ,Pattern Mask Bit 6" "Not used,Used" textline " " bitfld.long 0x0C 5. " PMASK5 ,Pattern Mask Bit 5" "Not used,Used" bitfld.long 0x0C 4. " PMASK4 ,Pattern Mask Bit 4" "Not used,Used" textline " " bitfld.long 0x0C 3. " PMASK3 ,Pattern Mask Bit 3" "Not used,Used" bitfld.long 0x0C 2. " PMASK2 ,Pattern Mask Bit 2" "Not used,Used" textline " " bitfld.long 0x0C 1. " PMASK1 ,Pattern Mask Bit 1" "Not used,Used" bitfld.long 0x0C 0. " PMASK0 ,Pattern Mask Bit 0" "Not used,Used" group asd:0x0050++0x1F line.long 0x00 "BkgrndOffset,Background Color or Blink Offset Register" hexmask.long.tbyte 0x00 0.--23. 1. " BGOFF ,Blink Offset Value" line.long 0x04 "PixelMode,Pixel Mode Definition Setup Register" bitfld.long 0x04 15. " TRBSW ,2 and 2/3 Red/Blue Swap Bit" "Normal,Reversed" bitfld.long 0x04 14. " DSCAN ,Dual Scan Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 10.--13. " C ,Color Mode Definition Table" "LUT Data,Grayscale,Grayscale,Grayscale,3x8 Bits,16bit 565 mode,16bit 555 mode,Grayscale,Grayscale,Grayscale,Grayscale,Grayscale,Grayscale,Grayscale,16bit 555 mode,Grayscale" bitfld.long 0x04 6.--9. " M ,Blink Mode Definition Table" "Disabled,Pixels ANDed,Pixels ORed,PixelsXORed,To background,To offset single,To offset 888,Undefined,Undefined,Undefined,Undefined,Undefined,Dimmer single,Brighter single,Dimmer 888 mode,Brighter 888 mode" textline " " bitfld.long 0x04 3.--5. " S ,Output Shift Mode" "1-pixel,1-pxiel to 18bits,2-pixels,4-pixels,8-pixels,2 2/3 3-bit pixels,Dual scan,Undefined" bitfld.long 0x04 0.--2. " P ,Bits per Pixel Scanned Out" "Disabled,4-bit,8-bits,Reserved,16-bits,Reserved,24-bits,32-bits" line.long 0x08 "ParllfOut,Parallel Interface Write/Control Register" bitfld.long 0x08 8. " RD ,Read Control Bit" "0,1" hexmask.long.byte 0x08 0.--7. 1. " DAT ,Data Output During Write Cycle" line.long 0x0C "Parlllfln,Parallel Interface Read/Setup Register" hexmask.long.byte 0x0C 20.--23. 1. " ESTRT ,Enable Signal Start Value" hexmask.long.byte 0x0C 16.--19. 1. " CNT ,Counter Preload Value" textline " " hexmask.long.byte 0x0C 0.--7. 1. " DAT ,Data Input During Read Cycle" line.long 0x10 "CursorArdStart,Word location of the Top Left Corner of Cursor to be Displayed" hexmask.long 0x10 2.--31. 1. " ADR ,Cursor Address Start" line.long 0x14 "CursorAdrReset,Location of First Word of CUrsor to be Scanned after Last Line" hexmask.long 0x10 2.--31. 1. " ADR ,Cursor Address Reset" line.long 0x18 "CursorSize,Cursor Height Width and Step Size Register" hexmask.long.byte 0x18 10.--15. 1. " DLNS ,Dual Scan Lower Half Lines" bitfld.long 0x18 8.--9. " CSTEP ,Cursor Stepo Size" "16 pixels,32 pixels,48 pixels,64 pixels" textline " " hexmask.long.byte 0x18 2.--7. 1. " CLINS ,Cursor Lines" bitfld.long 0x18 0.--1. " CWID ,Cursor Width" "16 pixels,32 pixels,48 pixels,64 pixels" line.long 0x1C "CursorColor1,Cursor Color Overlaid when Cursor Value is 10" hexmask.long.tbyte 0x1C 0.--23. 1. " COLOR ,Image Color" group asd:0x0070++0x0B line.long 0x00 "CursorColor2,Cursor Color Overlaid when Cursor Value is 11 Register" hexmask.long.tbyte 0x00 0.--23. 1. " COLOR ,Image Color" line.long 0x04 "CursorXYLoc,Cursor X and Y Location Register" hexmask.long.word 0x04 16.--26. 1. " YLOC ,Cursor Y Location" bitfld.long 0x04 15. " CEN ,Cursor Enable" "Disabled,Enabled" textline " " hexmask.long.word 0x04 0.--10. 1. " XLOC ,Cursor X Location" line.long 0x08 "CursorDScanLHYLoc,Cursor Dual Scan Lower Half Y Location Register" bitfld.long 0x08 15. " CLHEN ,Cursor Lower Half Enable" "Disabled,Enabled" hexmask.long.word 0x08 0.--10. 1. " YLOC ,Cursor Y Location" group asd:0x021C++0x0B line.long 0x00 "CursorBlinkColor1,Color when Cursor Value is 10 and Cursor is in Blink State Register" hexmask.long.tbyte 0x00 0.--23. 1. " COLOR ,Image Color" line.long 0x04 "CursorBlinkColor2,Color when Cursor Value is 11 and Cursor is in Blink State Register" hexmask.long.tbyte 0x04 0.--23. 1. " COLOR ,Image Color" line.long 0x08 "CurBlinkRateCtrl,Enable and Rate For Cursor Blinking Register" bitfld.long 0x08 8. " EN ,Hardware Cursor Blinking Enable" "Disabled,Enabled" hexmask.long.byte 0x08 0.--7. 1. " RATE ,Rate Value" group asd:0x007C++3 line.long 0x00 "RasterSWLock,Software Lock Register" hexmask.long.byte 0x00 0.--7. 1. " SWLOCK ,Software Lock Bits" rgroup asd:0x0200++3 line.long 0x00 "VidSigRsltVal,Video Signature Reset Value Register" hexmask.long.word 0x00 0.--15. 1. " SIGVAL ,Video Output Signature" group asd:0x0204++0x0B line.long 0x00 "VidSigCtrl,Video Signature Control Register" bitfld.long 0x00 31. " EN ,Linear Feedback Shift Register Enable" "Disabled,Enabled" bitfld.long 0x00 29. " SPCLK ,SPCLK Output Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 28. " BRIGHT ,Brightness Control Enable" "Disabled,Enabled" bitfld.long 0x00 27. " CLKEN ,CLKEN Control Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " BLANK ,BLANK Output Enable" "Disabled,Enabled" bitfld.long 0x00 25. " HSYNC ,HSYNC Output Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 24. " VSYNC ,VSYNC Output Enable" "Disabled,Enabled" hexmask.long.tbyte 0x00 0.--23. 1. " PEN ,Individual Pixels Enable" line.long 0x04 "VSigStrtStop,Vertical Signature Bounds Setup Register" hexmask.long.word 0x04 16.--26. 1. " STOP ,Value when VSIGEN Signal Becomes Inactive" hexmask.long.word 0x04 0.--10. 1. " STRT ,Value when VSIGEN Signal Becomes Active" line.long 0x08 "HSigStrtStop,Horizontal Signature Bounds Setup" hexmask.long.word 0x08 16.--26. 1. " STOP ,Value when HSIGEN Signal Becomes Inactive" hexmask.long.word 0x08 0.--10. 1. " STRT ,Value when HSIGEN Signal Becomes Active" group asd:0x0210++3 line.long 0x00 "SigClrStr,Signature Clear and Store Location Register" hexmask.long.word 0x00 16.--26. 1. " VCLR ,Value when VSIGCLR Signal is Active" hexmask.long.word 0x00 0.--10. 1. " HCLR ,Value when HSIGCLR Signal is Active" group asd:0x0214++3 line.long 0x00 "ACRate,LCD AC Voltage Bias Control Counter Setup Register" hexmask.long.word 0x00 0.--10. 1. " RATE ,Number of Horizontal Video Lines Before AC LCD Bias Signal Switches States" group asd:0x0218++3 line.long 0x00 "LUTSwCtrl,LUT Switching Control Register" bitfld.long 0x00 1. " SSTAT ,LUT Status" "Low,High" bitfld.long 0x00 0. " SWITCH ,LUT Requesting" "RAM0,RAM1" group asd:0x0230++3 line.long 0x00 "EOLOffset,End of Line Offset Register" hexmask.long.word 0x00 0.--15. 1. " OFFSET ,End of Line Offset Value" group asd:0x0234++3 line.long 0x00 "FIFOLevel,FIFO Fill Level Register" hexmask.long.byte 0x00 0.--5. 1. " LEVEL ,FIFO Refill Level Value" ;end include file ep9312/raster/rasterengine.ph tree "ColorLUT Registers" base asd:0x80030400 ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0000 group asd:0x0000++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0004 group asd:0x0004++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0008 group asd:0x0008++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x000C group asd:0x000C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0010 group asd:0x0010++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0014 group asd:0x0014++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0018 group asd:0x0018++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x001C group asd:0x001C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0020 group asd:0x0020++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0024 group asd:0x0024++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0028 group asd:0x0028++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x002C group asd:0x002C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0030 group asd:0x0030++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0034 group asd:0x0034++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0038 group asd:0x0038++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x003C group asd:0x003C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0040 group asd:0x0040++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0044 group asd:0x0044++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0048 group asd:0x0048++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x004C group asd:0x004C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0050 group asd:0x0050++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0054 group asd:0x0054++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0058 group asd:0x0058++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x005C group asd:0x005C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0060 group asd:0x0060++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0064 group asd:0x0064++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0068 group asd:0x0068++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x006C group asd:0x006C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0070 group asd:0x0070++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0074 group asd:0x0074++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0078 group asd:0x0078++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x007C group asd:0x007C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0080 group asd:0x0080++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0084 group asd:0x0084++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0088 group asd:0x0088++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x008C group asd:0x008C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0090 group asd:0x0090++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0094 group asd:0x0094++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0098 group asd:0x0098++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x009C group asd:0x009C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00A0 group asd:0x00A0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00A4 group asd:0x00A4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00A8 group asd:0x00A8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00AC group asd:0x00AC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00B0 group asd:0x00B0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00B4 group asd:0x00B4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00B8 group asd:0x00B8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00BC group asd:0x00BC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00C0 group asd:0x00C0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00C4 group asd:0x00C4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00C8 group asd:0x00C8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00CC group asd:0x00CC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00D0 group asd:0x00D0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00D4 group asd:0x00D4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00D8 group asd:0x00D8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00DC group asd:0x00DC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00E0 group asd:0x00E0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00E4 group asd:0x00E4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00E8 group asd:0x00E8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00EC group asd:0x00EC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00F0 group asd:0x00F0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00F4 group asd:0x00F4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00F8 group asd:0x00F8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x00FC group asd:0x00FC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0100 group asd:0x0100++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0104 group asd:0x0104++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0108 group asd:0x0108++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x010C group asd:0x010C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0110 group asd:0x0110++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0114 group asd:0x0114++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0118 group asd:0x0118++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x011C group asd:0x011C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0120 group asd:0x0120++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0124 group asd:0x0124++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0128 group asd:0x0128++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x012C group asd:0x012C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0130 group asd:0x0130++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0134 group asd:0x0134++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0138 group asd:0x0138++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x013C group asd:0x013C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0140 group asd:0x0140++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0144 group asd:0x0144++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0148 group asd:0x0148++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x014C group asd:0x014C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0150 group asd:0x0150++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0154 group asd:0x0154++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0158 group asd:0x0158++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x015C group asd:0x015C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0160 group asd:0x0160++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0164 group asd:0x0164++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0168 group asd:0x0168++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x016C group asd:0x016C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0170 group asd:0x0170++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0174 group asd:0x0174++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0178 group asd:0x0178++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x017C group asd:0x017C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0180 group asd:0x0180++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0184 group asd:0x0184++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0188 group asd:0x0188++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x018C group asd:0x018C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0190 group asd:0x0190++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0194 group asd:0x0194++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0198 group asd:0x0198++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x019C group asd:0x019C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01A0 group asd:0x01A0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01A4 group asd:0x01A4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01A8 group asd:0x01A8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01AC group asd:0x01AC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01B0 group asd:0x01B0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01B4 group asd:0x01B4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01B8 group asd:0x01B8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01BC group asd:0x01BC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01C0 group asd:0x01C0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01C4 group asd:0x01C4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01C8 group asd:0x01C8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01CC group asd:0x01CC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01D0 group asd:0x01D0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01D4 group asd:0x01D4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01D8 group asd:0x01D8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01DC group asd:0x01DC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01E0 group asd:0x01E0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01E4 group asd:0x01E4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01E8 group asd:0x01E8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01EC group asd:0x01EC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01F0 group asd:0x01F0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01F4 group asd:0x01F4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01F8 group asd:0x01F8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x01FC group asd:0x01FC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0200 group asd:0x0200++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0204 group asd:0x0204++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0208 group asd:0x0208++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x020C group asd:0x020C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0210 group asd:0x0210++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0214 group asd:0x0214++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0218 group asd:0x0218++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x021C group asd:0x021C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0220 group asd:0x0220++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0224 group asd:0x0224++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0228 group asd:0x0228++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x022C group asd:0x022C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0230 group asd:0x0230++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0234 group asd:0x0234++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0238 group asd:0x0238++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x023C group asd:0x023C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0240 group asd:0x0240++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0244 group asd:0x0244++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0248 group asd:0x0248++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x024C group asd:0x024C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0250 group asd:0x0250++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0254 group asd:0x0254++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0258 group asd:0x0258++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x025C group asd:0x025C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0260 group asd:0x0260++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0264 group asd:0x0264++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0268 group asd:0x0268++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x026C group asd:0x026C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0270 group asd:0x0270++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0274 group asd:0x0274++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0278 group asd:0x0278++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x027C group asd:0x027C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0280 group asd:0x0280++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0284 group asd:0x0284++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0288 group asd:0x0288++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x028C group asd:0x028C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0290 group asd:0x0290++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0294 group asd:0x0294++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0298 group asd:0x0298++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x029C group asd:0x029C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02A0 group asd:0x02A0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02A4 group asd:0x02A4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02A8 group asd:0x02A8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02AC group asd:0x02AC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02B0 group asd:0x02B0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02B4 group asd:0x02B4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02B8 group asd:0x02B8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02BC group asd:0x02BC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02C0 group asd:0x02C0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02C4 group asd:0x02C4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02C8 group asd:0x02C8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02CC group asd:0x02CC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02D0 group asd:0x02D0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02D4 group asd:0x02D4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02D8 group asd:0x02D8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02DC group asd:0x02DC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02E0 group asd:0x02E0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02E4 group asd:0x02E4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02E8 group asd:0x02E8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02EC group asd:0x02EC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02F0 group asd:0x02F0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02F4 group asd:0x02F4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02F8 group asd:0x02F8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x02FC group asd:0x02FC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0300 group asd:0x0300++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0304 group asd:0x0304++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0308 group asd:0x0308++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x030C group asd:0x030C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0310 group asd:0x0310++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0314 group asd:0x0314++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0318 group asd:0x0318++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x031C group asd:0x031C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0320 group asd:0x0320++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0324 group asd:0x0324++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0328 group asd:0x0328++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x032C group asd:0x032C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0330 group asd:0x0330++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0334 group asd:0x0334++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0338 group asd:0x0338++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x033C group asd:0x033C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0340 group asd:0x0340++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0344 group asd:0x0344++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0348 group asd:0x0348++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x034C group asd:0x034C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0350 group asd:0x0350++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0354 group asd:0x0354++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0358 group asd:0x0358++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x035C group asd:0x035C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0360 group asd:0x0360++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0364 group asd:0x0364++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0368 group asd:0x0368++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x036C group asd:0x036C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0370 group asd:0x0370++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0374 group asd:0x0374++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0378 group asd:0x0378++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x037C group asd:0x037C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0380 group asd:0x0380++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0384 group asd:0x0384++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0388 group asd:0x0388++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x038C group asd:0x038C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0390 group asd:0x0390++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0394 group asd:0x0394++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x0398 group asd:0x0398++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x039C group asd:0x039C++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03A0 group asd:0x03A0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03A4 group asd:0x03A4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03A8 group asd:0x03A8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03AC group asd:0x03AC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03B0 group asd:0x03B0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03B4 group asd:0x03B4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03B8 group asd:0x03B8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03BC group asd:0x03BC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03C0 group asd:0x03C0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03C4 group asd:0x03C4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03C8 group asd:0x03C8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03CC group asd:0x03CC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03D0 group asd:0x03D0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03D4 group asd:0x03D4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03D8 group asd:0x03D8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03DC group asd:0x03DC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03E0 group asd:0x03E0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03E4 group asd:0x03E4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03E8 group asd:0x03E8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03EC group asd:0x03EC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03F0 group asd:0x03F0++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03F4 group asd:0x03F4++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03F8 group asd:0x03F8++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph ;begin include file ep9312/raster/colorlut.ph ;parameters: 0x03FC group asd:0x03FC++3 line.long 0x00 "ColorLUT,Color Look-Up Table Register" hexmask.long.byte 0x00 16.--23. 1. " R ,Red Look-Up Value" hexmask.long.byte 0x00 8.--15. 1. " G ,Green Look-Up Value" hexmask.long.byte 0x00 0.--7. 1. " B ,Blue Look-Up Value" ;end include file ep9312/raster/colorlut.ph tree.end tree "GrySclLUTR Registers" base asd:0x80030080 ;begin include file ep9312/raster/lut.ph ;parameters: 0x0000 R if (0x0000<0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0000==0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0000++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0004 R if (0x0004<0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0004==0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0004++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0008 R if (0x0008<0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0008==0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0008++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x000C R if (0x000C<0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x000C==0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x000C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0010 R if (0x0010<0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0010==0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0010++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0014 R if (0x0014<0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0014==0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0014++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0018 R if (0x0018<0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0018==0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0018++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x001C R if (0x001C<0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x001C==0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x001C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0020 R if (0x0020<0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0020==0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0020++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0024 R if (0x0024<0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0024==0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0024++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0028 R if (0x0028<0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0028==0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0028++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x002C R if (0x002C<0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x002C==0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x002C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0030 R if (0x0030<0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0030==0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0030++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0034 R if (0x0034<0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0034==0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0034++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0038 R if (0x0038<0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0038==0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0038++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x003C R if (0x003C<0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x003C==0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x003C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0040 R if (0x0040<0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0040==0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0040++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0044 R if (0x0044<0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0044==0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0044++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0048 R if (0x0048<0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0048==0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0048++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x004C R if (0x004C<0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x004C==0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x004C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0050 R if (0x0050<0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0050==0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0050++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0054 R if (0x0054<0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0054==0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0054++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0058 R if (0x0058<0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0058==0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0058++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x005C R if (0x005C<0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x005C==0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x005C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0060 R if (0x0060<0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0060==0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0060++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0064 R if (0x0064<0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0064==0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0064++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0068 R if (0x0068<0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0068==0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0068++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x006C R if (0x006C<0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x006C==0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x006C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0070 R if (0x0070<0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0070==0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0070++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0074 R if (0x0074<0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0074==0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0074++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0078 R if (0x0078<0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0078==0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0078++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x007C R if (0x007C<0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x007C==0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x007C++3 line.long 0x00 "GrySclLUTR,Grayscale Look-Up-Table R Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph tree.end tree "GrySclLUTG Registers" base asd:0x80030280 ;begin include file ep9312/raster/lut.ph ;parameters: 0x0000 G if (0x0000<0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0000==0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0000++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0004 G if (0x0004<0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0004==0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0004++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0008 G if (0x0008<0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0008==0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0008++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x000C G if (0x000C<0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x000C==0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x000C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0010 G if (0x0010<0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0010==0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0010++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0014 G if (0x0014<0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0014==0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0014++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0018 G if (0x0018<0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0018==0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0018++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x001C G if (0x001C<0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x001C==0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x001C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0020 G if (0x0020<0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0020==0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0020++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0024 G if (0x0024<0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0024==0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0024++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0028 G if (0x0028<0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0028==0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0028++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x002C G if (0x002C<0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x002C==0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x002C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0030 G if (0x0030<0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0030==0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0030++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0034 G if (0x0034<0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0034==0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0034++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0038 G if (0x0038<0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0038==0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0038++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x003C G if (0x003C<0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x003C==0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x003C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0040 G if (0x0040<0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0040==0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0040++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0044 G if (0x0044<0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0044==0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0044++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0048 G if (0x0048<0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0048==0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0048++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x004C G if (0x004C<0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x004C==0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x004C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0050 G if (0x0050<0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0050==0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0050++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0054 G if (0x0054<0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0054==0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0054++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0058 G if (0x0058<0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0058==0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0058++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x005C G if (0x005C<0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x005C==0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x005C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0060 G if (0x0060<0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0060==0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0060++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0064 G if (0x0064<0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0064==0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0064++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0068 G if (0x0068<0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0068==0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0068++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x006C G if (0x006C<0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x006C==0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x006C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0070 G if (0x0070<0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0070==0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0070++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0074 G if (0x0074<0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0074==0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0074++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0078 G if (0x0078<0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0078==0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0078++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x007C G if (0x007C<0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x007C==0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x007C++3 line.long 0x00 "GrySclLUTG,Grayscale Look-Up-Table G Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph tree.end tree "GrySclLUTB Registers" base asd:0x80030300 ;begin include file ep9312/raster/lut.ph ;parameters: 0x0000 B if (0x0000<0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0000==0x001C) group asd:0x0000++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0000++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0004 B if (0x0004<0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0004==0x001C) group asd:0x0004++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0004++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0008 B if (0x0008<0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0008==0x001C) group asd:0x0008++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0008++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x000C B if (0x000C<0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x000C==0x001C) group asd:0x000C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x000C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0010 B if (0x0010<0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0010==0x001C) group asd:0x0010++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0010++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0014 B if (0x0014<0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0014==0x001C) group asd:0x0014++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0014++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0018 B if (0x0018<0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0018==0x001C) group asd:0x0018++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0018++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x001C B if (0x001C<0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x001C==0x001C) group asd:0x001C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x001C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0020 B if (0x0020<0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0020==0x001C) group asd:0x0020++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0020++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0024 B if (0x0024<0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0024==0x001C) group asd:0x0024++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0024++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0028 B if (0x0028<0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0028==0x001C) group asd:0x0028++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0028++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x002C B if (0x002C<0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x002C==0x001C) group asd:0x002C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x002C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0030 B if (0x0030<0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0030==0x001C) group asd:0x0030++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0030++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0034 B if (0x0034<0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0034==0x001C) group asd:0x0034++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0034++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0038 B if (0x0038<0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0038==0x001C) group asd:0x0038++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0038++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x003C B if (0x003C<0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x003C==0x001C) group asd:0x003C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x003C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0040 B if (0x0040<0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0040==0x001C) group asd:0x0040++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0040++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0044 B if (0x0044<0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0044==0x001C) group asd:0x0044++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0044++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0048 B if (0x0048<0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0048==0x001C) group asd:0x0048++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0048++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x004C B if (0x004C<0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x004C==0x001C) group asd:0x004C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x004C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0050 B if (0x0050<0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0050==0x001C) group asd:0x0050++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0050++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0054 B if (0x0054<0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0054==0x001C) group asd:0x0054++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0054++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0058 B if (0x0058<0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0058==0x001C) group asd:0x0058++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0058++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x005C B if (0x005C<0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x005C==0x001C) group asd:0x005C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x005C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0060 B if (0x0060<0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0060==0x001C) group asd:0x0060++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0060++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0064 B if (0x0064<0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0064==0x001C) group asd:0x0064++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0064++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0068 B if (0x0068<0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0068==0x001C) group asd:0x0068++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0068++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x006C B if (0x006C<0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x006C==0x001C) group asd:0x006C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x006C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0070 B if (0x0070<0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0070==0x001C) group asd:0x0070++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0070++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0074 B if (0x0074<0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0074==0x001C) group asd:0x0074++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0074++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x0078 B if (0x0078<0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x0078==0x001C) group asd:0x0078++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x0078++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph ;begin include file ep9312/raster/lut.ph ;parameters: 0x007C B if (0x007C<0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" elif (0x007C==0x001C) group asd:0x007C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" bitfld.long 0x00 18. " FRAME ,Frame Counter Selection" "FRAME_CNT3,FRAME_CNT4" bitfld.long 0x00 17. " VERT ,Vertical Counter Selection" "VERT_CNT3,VERT_CNT4" bitfld.long 0x00 16. " HORZ ,Horizontal Counter Selection" "HORZ_CNT3,HORZ_CNT4" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" else group asd:0x007C++3 line.long 0x00 "GrySclLUTB,Grayscale Look-Up-Table B Register" hexmask.long.word 0x00 0.--15. 1. " D ,Matrix Position Enable Bits" endif ;end include file ep9312/raster/lut.ph tree.end ;end include file ep9312/raster.ph tree.end width 16. 8. tree "1/10/100 Mbps Ethernet LAN Controller" base asd:0x80010000 ;begin include file ep9312/lan.ph ;parameters: tree "Control Registers" group asd:0x0000++0x0B line.long 0x00 "RXCtl,MAC Receiver Control Register" bitfld.long 0x00 20. " PauseA ,Pause Accept" "Clear,Set" bitfld.long 0x00 19. " RxFCE1 ,Rx Flow Control Enable Bit 1" "Disabled,Enabled" textline " " bitfld.long 0x00 18. " RxFCE0 ,Rx Flow Control Enable Bit 0" "Disabled,Enabled" bitfld.long 0x00 17. " BCRC ,Buffer CRC" "Not receive,Receive" textline " " bitfld.long 0x00 16. " SRxON ,Serial Receive On" "Disabled,Enabled" bitfld.long 0x00 13. " RCRCA ,Runt CRCA" "Clear,Set" textline " " bitfld.long 0x00 12. " RA ,Runt A" "Clear,Set" bitfld.long 0x00 11. " PA ,Promiscuous" "Clear,Set" textline " " bitfld.long 0x00 10. " BA ,Broadcast A" "Clear,Set" bitfld.long 0x00 9. " MA ,Mulitcast A" "Clear,Set" textline " " bitfld.long 0x00 8. " IAHA ,Individual Address Hash A" "Clear,Set" bitfld.long 0x00 3. " IA3 ,Individual Accept 3" "Clear,Set" textline " " bitfld.long 0x00 2. " IA2 ,Individual Accept 2" "Clear,Set" bitfld.long 0x00 1. " IA1 ,Individual Accept 1" "Clear,Set" textline " " bitfld.long 0x00 0. " IA0 ,Individual Accept 0" "Clear,Set" line.long 0x04 "TXCtl,MAC Transmitter Control Register" bitfld.long 0x04 7. " DefDis ,2-part Defeferral Disable" "Enabled,Disabled" bitfld.long 0x04 6. " MBE ,Mopdified Backoff Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 5. " ICRC ,Inhibit CRC" "Clear,Set" bitfld.long 0x04 4. " TxPD ,Tx Pad Disable" "Enabled,Disabled" textline " " bitfld.long 0x04 3. " OColl ,One Collision" "Clear,Set" bitfld.long 0x04 2. " SP ,Send Pause" "No transmit,Transmit" textline " " bitfld.long 0x04 1. " PB ,Pause Busy" "No pause is transmitting,Pause is transmitting" bitfld.long 0x04 0. " STxON ,Serial Transmitt On" "Disabled,Enabled" line.long 0x08 "TestCtl,MAC Test Control Register" bitfld.long 0x08 7. " MACF ,MAC Fast" "Normal timing,Speed-up" bitfld.long 0x08 6. " MFDX ,MAC Full Duplex" "Disabled,Enabled" textline " " bitfld.long 0x08 5. " DB ,Disable Backoff" "Enabled,Disabled" group asd:0x0020++0x0B line.long 0x00 "SelfCtl,MAC Self Control Register" hexmask.long.byte 0x00 9.--14. 1. " MDCDIV ,MDC Clock Divisior" bitfld.long 0x00 8. " PSPRS ,Preamble Supress" "32 ones before SFD,SFD no MDIO" textline " " bitfld.long 0x00 7. " RWP ,Remote Wake Pin" "No,Yes" bitfld.long 0x00 5. " GPO8 ,General Purpose Output 0" "Low,High" textline " " bitfld.long 0x00 4. " PUWE ,Power Up Wakeup Enable" "Disabled,Enabled" bitfld.long 0x00 3. " PDWE ,Power Down Wakeup Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " MIIL ,MII Loopback" "No loopback,Loopback" bitfld.long 0x00 0. " RESET ,Soft Reset" "No effect,Reset" line.long 0x04 "IntEn,MAC Intrerrupt Enable Register" bitfld.long 0x04 30. " RWIE ,Remote Wakeup Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 29. " RxMIE ,Receive Miss Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 28. " RxBIE ,Receive Buffer Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 27. " RxSQIE ,Receive Status Queue Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 26. " TxLEIE ,Transmit Length Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 25. " ECIE ,End of Chain Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 24. " TxUHIE ,Transmit Underrun Halt Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 18. " MOIE ,Receive Miss Overflow Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 17. " TxCOIE ,Transmit Collision Overflow Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 16. " RxROIE ,Receive Runt Overflow Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 12. " MIIE ,MII Management Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 11. " PHYSIE ,PHY Status Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 10. " TIE ,Timer Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 8. " SWIE ,Software Interrupt" "Not generated,Generated" textline " " bitfld.long 0x04 3. " TSQIE ,Transmit Status Queue Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 2. " REOFIE ,Receive End of Frame Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 1. " REOBIE ,Receive End of Buffer Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 0. " RHDRIE ,Receive Header Interrupt Enable" "Disabled,Enabled" line.long 0x08 "IntStsP,MAC Interrupt Status Preserve Register" bitfld.long 0x08 30. " RWI ,Remote Wakeup Interrupt" "No interrupt,Interrupt" bitfld.long 0x08 29. " RxMI ,Receive Frame Discarded" "No interrupt,Interrupt" textline " " bitfld.long 0x08 28. " RxBI ,Last Available Descriptor Read to MAC" "No interrupt,Interrupt" bitfld.long 0x08 27. " RxSQI ,Receive Status Queue" "No interrupt,Interrupt" textline " " bitfld.long 0x08 26. " TxLEI ,Transmit Length Error" "No interrupt,Interrupt" bitfld.long 0x08 25. " ECI ,Exhausted Transmit Descriptor Chain" "No interrupt,Interrupt" textline " " bitfld.long 0x08 24. " TxUHI ,Out of Data during Transmission" "No interrupt,Interrupt" bitfld.long 0x08 18. " MOI ,Received Frames Lost in Buffer" "No interrupt,Interrupt" textline " " bitfld.long 0x08 17. " TxCOI ,Transmit Collision" "No interrupt,Interrupt" bitfld.long 0x08 16. " RxROI ,Receive Collision" "No interrupt,Interrupt" textline " " bitfld.long 0x08 12. " MIII ,Management Operation on MII Completed" "No interrupt,Interrupt" bitfld.long 0x08 11. " PHYI ,SHY Status Change" "No interrupt,Interrupt" textline " " bitfld.long 0x08 10. " TI ,GT Timer Reaches Zero" "No interrupt,Interrupt" bitfld.long 0x08 9. " AHBE ,AHB Cycle Terminated Incorrectly" "No interrupt,Interrupt" textline " " bitfld.long 0x08 8. " SWI ," "0,1" bitfld.long 0x08 4. " OTHER ,Status of others that bits 2,3,10 Present" "Clear,Set" textline " " bitfld.long 0x08 3. " TxSQ ,Status Affecting Transmit Status Queue" "No,Yes" bitfld.long 0x08 2. " RxSQ ,Status Affecting Receive Status Queue" "No,Yes" rgroup asd:0x002C++3 line.long 0x00 "IntStsC,MAC Interrupt Status Clear Register" bitfld.long 0x00 30. " RWI ,Remote Wakeup Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 29. " RxMI ,Receive Frame Discarded" "No interrupt,Interrupt" textline " " bitfld.long 0x00 28. " RxBI ,Last Available Descriptor Read to MAC" "No interrupt,Interrupt" bitfld.long 0x00 27. " RxSQI ,Receive Status Queue" "No interrupt,Interrupt" textline " " bitfld.long 0x00 26. " TxLEI ,Transmit Length Error" "No interrupt,Interrupt" bitfld.long 0x00 25. " ECI ,Exhausted Transmit Descriptor Chain" "No interrupt,Interrupt" textline " " bitfld.long 0x00 24. " TxUHI ,Out of Data during Transmission" "No interrupt,Interrupt" bitfld.long 0x00 18. " MOI ,Received Frames Lost in Buffer" "No interrupt,Interrupt" textline " " bitfld.long 0x00 17. " TxCOI ,Transmit Collision" "No interrupt,Interrupt" bitfld.long 0x00 16. " RxROI ,Receive Collision" "No interrupt,Interrupt" textline " " bitfld.long 0x00 12. " MIII ,Management Operation on MII Completed" "No interrupt,Interrupt" bitfld.long 0x00 11. " PHYI ,SHY Status Change" "No interrupt,Interrupt" textline " " bitfld.long 0x00 10. " TI ,GT Timer Reaches Zero" "No interrupt,Interrupt" bitfld.long 0x00 9. " AHBE ,AHB Cycle Terminated Incorrectly" "No interrupt,Interrupt" textline " " bitfld.long 0x00 8. " SWI ," "0,1" bitfld.long 0x00 4. " OTHER ,Status of others that bits 2,3,10 Present" "Clear,Set" textline " " bitfld.long 0x00 3. " TxSQ ,Status Affecting Transmit Status Queue" "No,Yes" bitfld.long 0x00 2. " RxSQ ,Status Affecting Receive Status Queue" "No,Yes" group asd:0x0038++0x17 line.long 0x00 "DiagAd,MAC Diagnostic Address Register" hexmask.long.byte 0x00 0.--7. 1. " ADDR ,Diagnostic Address" line.long 0x04 "DiagDa,MAC Diagnostic Data" hexfld.long 0x04 " DATA ,Diagnostic Data Register" line.long 0x08 "GT,MAC General Timer Register" hexmask.long.word 0x08 16.--31. 1. " GTC ,General Timer Count" hexmask.long.word 0x08 0.--15. 1. " GTP ,General Timer Period" line.long 0x0C "FCT,MAC Flow Control Timer Register" hexmask.long.tbyte 0x0C 0.--31. 1. " FCT ,Flow Control Timer Value" line.long 0x10 "FCF,MAC Flow Control Format Register" hexmask.long.word 0x10 16.--31. 1. " MACCT ,MAC Control Type" hexmask.long.word 0x10 0.--15. 1. " TPT ,Transmit Pause Time" line.long 0x14 "AFP,MAC Address Filter Pointer Register" bitfld.long 0x14 0.--2. " AFP ,Address Filter Pointer" "Primary individual,Secondary address,Secondary address,Secondary address,Reserved,Reserved,Destination address,Hash table used" group asd:0x0050++7 line.quad 0x00 "IndAd,MAC Individual Address Register" hexmask.quad 0x00 0.--47. 1. " IAD ,Individual Address" group asd:0x0050++7 line.quad 0x00 "HashTbl,MAC Hash Table Register" hexfld.quad 0x00 " HTb ,Hash Table" group asd:0x0060++7 line.long 0x00 "GIIntSts,MAC Global Interrupt Status Register" bitfld.long 0x00 15. " INT ,Global Interrupt Bit" "Interrupt not occured,Interrupt occured" line.long 0x04 "GlIntMsk,MAC Global Interrupt Mask Register" bitfld.long 0x04 15. " INT ,Global Interrupt Mask Bit" "Not masked,Masked" rgroup asd:0x0068++3 line.long 0x00 "GIIntROSts,MAC Global Interrupt Read-Only Status Register" bitfld.long 0x00 15. " INT ,Global Interrupt Read-Only Status Bit" "Interrupt not occured,Interrupt occured" wgroup asd:0x006C++3 line.long 0x00 "GIIntFrc,MAC Global Interrupt Force Register" bitfld.long 0x00 15. " INT ,Global Interrupt Force Bit" "No effect,Enabled" rgroup asd:0x0070++0x0B line.long 0x00 "TXCollCnt,MAC Transmission Collision Count Register" hexmask.long.word 0x00 0.--15. 1. " TXC ,Transmission Collision Count Value" line.long 0x04 "RXMissCnt,MAC Receive Miss Count Register" hexmask.long.word 0x04 0.--15. 1. " RMC ,Receive Miss Count Value" line.long 0x08 "RXRuntCnt,MAC Receive Runt Count Register" hexmask.long.word 0x08 0.--15. 1. " RRC ,Receive Runt Count" tree.end tree "MII/PHY Registers" group asd:0x0010++7 line.long 0x00 "MIICmd,MAC MII Command Registers" bitfld.long 0x00 14.--15. " OP ,OP Code" "Reserved,Write,Read,Reserved" hexmask.long.byte 0x00 10.--13. 1. " PHYAD ,PHY Address" hexmask.long.byte 0x00 0.--4. 1. " REGAD ,Register Address" line.long 0x04 "MIData,MAC MII Data Register" hexmask.long.word 0x04 0.--15. 1. " MIIData ,MII Data" rgroup asd:0x0018++3 line.long 0x00 "MIISts,MAC MII Status Register" bitfld.long 0x00 0. " BUSY ,MII Busy" "Not busy,Busy" tree.end tree "Descriptor Processor Registers" group asd:0x0080++3 line.long 0x00 "BMCtl,MAC Bus Master Control Register" bitfld.long 0x00 13. " MT ,Manual Transfer" "No,Yes" bitfld.long 0x00 12. " TT ,Timed Transfer" "No,Yes" bitfld.long 0x00 11. " UnH ,Underrun Halt" "Not halted,Halted" textline " " bitfld.long 0x00 10. " TxChR ,Transmit Channel Reset" "No effect,Reset" bitfld.long 0x00 9. " TxDis ,Transmit Disable" "Enabled,Disabled" bitfld.long 0x00 8. " TxEn ,Transmit Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 6. " EH2 ,Enable Header 2" "Disabled,Enabled" bitfld.long 0x00 5. " EH1 ,Enable Header 1" "Disabled,Enabled" bitfld.long 0x00 4. " EEOB ,Enable EOB" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " RxChR ,Receive Channel Reset" "No effect,Reset" bitfld.long 0x00 1. " RxDis ,Receive Disable" "Enabled,Disabled" bitfld.long 0x00 0. " RxEn ,Receive Enable" "Disabled,Enabled" rgroup asd:0x0084++3 line.long 0x00 "BMSts,MAC Bus Master Status Register" bitfld.long 0x00 7. " TxAct ,Transmit Active" "Not active,Active" bitfld.long 0x00 4. " TP ,Transfer Pending" "Not pending,Pending" bitfld.long 0x00 3. " RxAct ,Receive Active" "Not active,Active" textline " " bitfld.long 0x00 0.--2. " QID ,Queue ID" "Receive data,Transmit data,Receive status,Transmit status,Receive descriptor,Transmit descriptor,," tree.end tree "Descriptor Processor Receive" group asd:0x0088++3 line.long 0x00 "RXBCA,MAC Receive Buffer Current Address Register" hexfld.long 0x00 " RBCA ,Receive Buffer Current Address" group asd:0x0090++0x03 line.long 0x00 "RXDQBAdd,MAC Receive Descriptor Queue Base Address Register" hexfld.long 0x00 " RDBA ,Receive Descriptor Base Address" group asd:0x0094++0x03 line.word 0x00 "RXDQBLen,MAC Receive Descriptor Queue Base Length Register" hexfld.word 0x00 " RDBL ,Receive Descriptor Length Address" line.word 0x02 "RXDQCurLen,MAC Receive Descriptor Queue Curent Length Register" hexfld.word 0x02 " RDCL ,Receive Descriptor Base Length" group asd:0x098++0x07 line.long 0x00 "RXDQCurAdd,MAC Receive Descriptor Queue Curent Address Register" hexmask.long.word 0x00 0.--15. 1. " RDCA ,Receive Descriptor Curent Address" line.long 0x04 "RXDEnq,MAC Receive Descriptor Enqueue Register" hexmask.long.word 0x04 16.--31. 1. " RDV ,Receive Descriptor Value" hexmask.long.byte 0x04 0.--7. 1. " RDI ,Receive Descriptor Incerment" group asd:0x00A0++0x03 line.long 0x00 "RxStsQBAdd,MAC Receive Status Queue Base Address Register" hexfld.long 0x00 " RSQBA ,Receive Status Queue Base Address" group asd:0x00A4++0x03 line.word 0x00 "RxStsQBLen,MAC Receive Status Queue Base Length Register" hexfld.word 0x00 " RSQBL ,Receive Status Queue Base Length" line.word 0x02 "RxStsQBCurLen,MAC Receive Status Queue Current Length Register" hexfld.word 0x02 " RSQCL ,Receive Status Queue Current Length" group asd:0x00A8++0x07 line.long 0x00 "RxStsQBCurAdd,MAC Receive Status Queue Address Register" hexfld.long 0x00 " RSQCA ,Receive Status Queue Address" line.long 0x04 "RxStsEnq,MAC Receive Status Enqueue Register" hexmask.long.word 0x04 16.--31. 1. " RSV ,Receive Status Value" hexmask.long.byte 0x04 0.--7. 1. " RSI ,Receive Stauts Incerment" tree.end tree "Descriptor Processor Transmit" group asd:0x00B0++0x03 line.long 0x00 "TXDQBAdd,MAC Transmit Descriptor Queue Base Address Register" hexfld.long 0x00 " TDBA ,Transmit Descriptor Base Address" group asd:0x00B4++0x03 line.word 0x00 "TXDQBLen,MAC Transmit Descriptor Queue Base Length Register" hexfld.word 0x00 " TDBL ,Transmit Descriptor Length Address" line.word 0x02 "TXDQCurLen,MAC Transmit Descriptor Queue Current Length Register" hexfld.word 0x02 " TDCL ,Transmit Descriptor Base Length" group asd:0x00B8++0x07 line.long 0x00 "TXDQCurAdd,MAC Transmit Descriptor Queue Current Address Register" hexfld.long 0x00 " TDCA ,Transmit Descriptor Curent Address" line.long 0x04 "TXDEnq,MAC Transmit Descriptor Enqueue Register" hexmask.long.word 0x04 16.--31. 1. " TDV ,Transmit Descriptor Value" hexmask.long.byte 0x04 0.--7. 1. " TDI ,Transmit Descriptor Incerment" group asd:0x00C0++0x03 line.long 0x00 "TXStsQBAdd,MAC Transmit Status Queue Base Address Register" hexfld.long 0x00 " TSQBA ,Transmit Status Queue Base Address" group asd:0x00C0++0x03 line.word 0x00 "TXStsQBLen,MAC Transmit Status Queue Base Length Register" hexfld.word 0x00 " TSQBL ,Transmit Status Queue Base Length" line.word 0x02 "TXStsQBCurLen,MAC Transmit Status Queue Current Address Register" hexfld.word 0x02 " TSQCL ,Transmit Status Queue Current Length" group asd:0x00C8++0x03 line.long 0x00 "TXStsQBCurAdd,MAC Transmit Status Queue Current Address Register" hexfld.long 0x00 " TSQCA ,Transmit Status Queue Address" group asd:0x00D0++0x0F line.long 0x00 "RXBufTrshld,MAC Receive Buffer Threshold Register" hexmask.long.byte 0x00 18.--25. 1. " RDHT ,Receive Data Hard Threshold" hexmask.long.byte 0x00 2.--9. 1. " RDST ,Receive Data Soft Threshold" line.long 0x04 "TXBufTrshld,MAC Transmit Buffer Threshold Register" hexmask.long.byte 0x04 18.--25. 1. " TDHT ,Transmit Data Hard Threshold" hexmask.long.byte 0x04 2.--9. 1. " TDST ,Transmit Data Soft Threshold" line.long 0x08 "RXStsTrshld,MAC Receive Status Threshold Register" hexmask.long.byte 0x08 18.--21. 1. " RSHT ,Receive Status Hard Threshold" hexmask.long.byte 0x08 2.--5. 1. " RSST ,Receive Status Soft Threshold" line.long 0x0C "TXStsTrshld,MAC Transmit Status Threshold Register" hexmask.long.byte 0x0C 18.--21. 1. " TSHT ,Transmit Status Hard Threshold" hexmask.long.byte 0x0C 2.--5. 1. " TSST ,Transmit Status Soft Threshold" group asd:0x00E0++0x0F line.long 0x00 "RXDTrshld,MAC Receive Descriptor Threshold Register" hexmask.long.byte 0x00 18.--21. 1. " RDHT ,Receive Descriptor Hard Threshold" hexmask.long.byte 0x00 2.--5. 1. " RDST ,Receive Descriptor Soft Threshold" line.long 0x04 "TXDTrshld,MAC Transmit Descriptor Threshold Register" hexmask.long.byte 0x04 18.--21. 1. " TDHT ,Transmit Descriptor Hard Threshold" hexmask.long.byte 0x04 2.--5. 1. " TDST ,Transmit Descriptor Soft Threshold" line.long 0x08 "MaxFrmLen,MAC Maximum Frame Length Register" hexmask.long.byte 0x08 16.--21. 1. " MFL ,Maximum Frame Length" hexmask.long.byte 0x08 0.--5. 1. " TST ,Transmit Start Threshold" line.long 0x0C "RXHdrLen,MAC Receive Header Length Register" hexmask.long.word 0x0C 16.--26. 1. " RHL2 ,Receive Header Length 2" hexmask.long.byte 0x0C 0.--9. 1. " RHL1 ,Receive Header Length 1" tree.end tree "MAC FIFO Memory" group asd:0x4000++3 hide.long 0x00 "MACFIFO,MAC FIFO RAM" button "MACFIFO" "d asd:0x80014000++0x10FF /long" tree.end ;end include file ep9312/lan.ph tree.end tree "DMA Controller" base asd:0x80000000 ;begin include file ep9312/dma.ph ;parameters: ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0000 0 tree "M2P Channel 0" group asd:0x0000++7 line.long 0x00 "CONTROL,Channel 0 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (0==0||0==2||0==4||0==6||0==8) group asd:(0x0000+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (0==1||0==3||0==5||0==7||0==9) group asd:(0x0000+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0000+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0000+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0000+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0000+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0000+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0000+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0040 1 tree "M2P Channel 1" group asd:0x0040++7 line.long 0x00 "CONTROL,Channel 1 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (1==0||1==2||1==4||1==6||1==8) group asd:(0x0040+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (1==1||1==3||1==5||1==7||1==9) group asd:(0x0040+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0040+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0040+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0040+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0040+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0040+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0040+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0080 2 tree "M2P Channel 2" group asd:0x0080++7 line.long 0x00 "CONTROL,Channel 2 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (2==0||2==2||2==4||2==6||2==8) group asd:(0x0080+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (2==1||2==3||2==5||2==7||2==9) group asd:(0x0080+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0080+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0080+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0080+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0080+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0080+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0080+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x00C0 3 tree "M2P Channel 3" group asd:0x00C0++7 line.long 0x00 "CONTROL,Channel 3 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (3==0||3==2||3==4||3==6||3==8) group asd:(0x00C0+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (3==1||3==3||3==5||3==7||3==9) group asd:(0x00C0+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x00C0+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x00C0+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x00C0+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x00C0+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x00C0+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x00C0+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2m.ph ;parameters: 0x0100 0 tree "M2M Channel 0" group asd:0x0100++7 line.long 0x00 "CONTROL,Channel 0 Control Register" hexmask.long.byte 0x00 25.--31. 1. " PSWC ,Peripheral Wait States Count" bitfld.long 0x00 24. " NO-HDSK ,Handshake Protocol Requirement" "Required,Not required" textline " " bitfld.long 0x00 22.--23. " RSS ,Request Source Selection" "External Dreq,Internal SSPRx,Internal SSPTx,Internal IDE" bitfld.long 0x00 21. " NFBIntEn ,Interrupt Generation in DMA_BUF_ON State" "Disabled,Enabled" textline " " bitfld.long 0x00 19.--20. " DREQP ,DMA Request Pin Polarity" "Active low level sensitive,Active high level sensitive,Active low edge sensitive,Active high edge sensitive" bitfld.long 0x00 17. " DACKP ,DMA Acknowledge Pin Polarity" "Active low,Active high" textline " " bitfld.long 0x00 16. " ERDP ,End of Transfer/Terminal Count Pin Direction & Polarity" "Active low,Active high" bitfld.long 0x00 15. " ETDP ,End of Transfer/Terminal Count Pin Direction & Polarity" "Active low,Active high" textline " " bitfld.long 0x00 13.--14. " TM ,Transfer Mode" "Software initiated M2M,Hardware Initiated M2P,Hardware Initiated P2M,Not used" bitfld.long 0x00 12. " SAH ,Source Address Hold" "Increment,Hold" textline " " bitfld.long 0x00 11. " DAH ,Destination Address Hold" "Increment,Hold" bitfld.long 0x00 9.--10. " PW ,Peripheral Width" "Byte,Halfword,Word,Not used" textline " " bitfld.long 0x00 5.--8. " BWC ,Bandwidth Control" "Full,16,16,16,16,32,64,128,256,512,1024,2048,4096,8192,16384,32768" bitfld.long 0x00 4. " START ,Start Transfer" "Stopped,Started" textline " " bitfld.long 0x00 3. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 2. " DONEIntEn ,DONE Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " SCT ,Source Copy Transfer" "Low,High" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " DONEInt ,Transaction Done Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" rgroup asd:(0x0100+0x000C)++3 line.long 0x00 "STATUS,Channel 0 Status Register" bitfld.long 0x00 13. " DREQS ,DREQ Status" "0,1" textline " " bitfld.long 0x00 12. " NB ,Next Buffer Status Bit" "0,1" textline " " bitfld.long 0x00 11. " NFB ,Next Buffer during Transfer Programmed" "Yes,No" textline " " bitfld.long 0x00 9.--10. " EOTS ,End-of-Transfer Status" "Not requested for any descriptor,Requested for descriptor 0,Requested for descriptor 1,Requested for all descriptors" textline " " bitfld.long 0x00 7.--8. " TCS ,Terminal Count Status" "Not reached for buffer descriptor 0 & 1,Not reached for buffer descriptor only for 0,Not reached for buffer descriptor only for 1,Reached for all" textline " " bitfld.long 0x00 6. " DONE ,Transfer Completed Succefully" "Not succesfully,Succefully" textline " " bitfld.long 0x00 4.--5. " CurrentState[4:3] ,M2M Buffer FSM" "NO_BUF,BUF_ON,BUF_NEXT,?..." textline " " bitfld.long 0x00 1.--3. " CurrentState[2:0] ,M2M Channel Control FSM" "IDLE,STALL,MEM_RD,MEM_WR,BWC_WAIT,?..." textline " " bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" group asd:(0x0100+0x0010)++0x0F line.long 0x00 "BCR0,Channel Byte Count Register 0" hexmask.long.word 0x00 0.--15. 1. " BCR0 ,Channel Bytes Count" line.long 0x04 "BCR1,Channel Byte Count Register 1" hexmask.long.word 0x04 0.--15. 1. " BCR0 ,Channel Bytes Count" line.long 0x08 "SAR_BASE0,Source Base Memory Address Register" hexfld.long 0x08 " SAR_BASE0 ,Base Memory Address" line.long 0x0C "SAR_BASE1,Source Base Memory Address Register" hexfld.long 0x0C " SAR_BASE1 ,Base Memory Address" rgroup asd:(0x0100+0x0024)++7. line.long 0x00 "SAR_CURRENT0,Source Base Memory Address Register 0" hexfld.long 0x00 " SAR_CURRENT0 ,Base Memory Address" line.long 0x04 "SAR_CURRENT1,Source Base Memory Address Register 1" hexfld.long 0x04 " SAR_CURRENT1 ,Base Memory Address" group asd:(0x0100+0x002C)++7. line.long 0x00 "DAR_BASE0,Destination Base Memory Address Register" hexfld.long 0x00 " DAR_BASE0 ,Base Memory Address" line.long 0x04 "DAR_BASE1,Destination Base Memory Address Register" hexfld.long 0x04 " DAR_BASE1 ,Base Memory Address" rgroup asd:(0x0100+0x0034)++3 line.long 0x00 "DAR_CURRENT0,Destination Base Memory Address Register 0" hexfld.long 0x00 " DAR_CURRENT0 ,Base Memory Address" rgroup asd:(0x0100+0x003C)++3 line.long 0x00 "DAR_CURRENT1,Destination Base Memory Address Register 0" hexfld.long 0x00 " DAR_CURRENT1 ,Base Memory Address" tree.end ;end include file ep9312/dma/m2m.ph ;begin include file ep9312/dma/m2m.ph ;parameters: 0x0140 1 tree "M2M Channel 1" group asd:0x0140++7 line.long 0x00 "CONTROL,Channel 1 Control Register" hexmask.long.byte 0x00 25.--31. 1. " PSWC ,Peripheral Wait States Count" bitfld.long 0x00 24. " NO-HDSK ,Handshake Protocol Requirement" "Required,Not required" textline " " bitfld.long 0x00 22.--23. " RSS ,Request Source Selection" "External Dreq,Internal SSPRx,Internal SSPTx,Internal IDE" bitfld.long 0x00 21. " NFBIntEn ,Interrupt Generation in DMA_BUF_ON State" "Disabled,Enabled" textline " " bitfld.long 0x00 19.--20. " DREQP ,DMA Request Pin Polarity" "Active low level sensitive,Active high level sensitive,Active low edge sensitive,Active high edge sensitive" bitfld.long 0x00 17. " DACKP ,DMA Acknowledge Pin Polarity" "Active low,Active high" textline " " bitfld.long 0x00 16. " ERDP ,End of Transfer/Terminal Count Pin Direction & Polarity" "Active low,Active high" bitfld.long 0x00 15. " ETDP ,End of Transfer/Terminal Count Pin Direction & Polarity" "Active low,Active high" textline " " bitfld.long 0x00 13.--14. " TM ,Transfer Mode" "Software initiated M2M,Hardware Initiated M2P,Hardware Initiated P2M,Not used" bitfld.long 0x00 12. " SAH ,Source Address Hold" "Increment,Hold" textline " " bitfld.long 0x00 11. " DAH ,Destination Address Hold" "Increment,Hold" bitfld.long 0x00 9.--10. " PW ,Peripheral Width" "Byte,Halfword,Word,Not used" textline " " bitfld.long 0x00 5.--8. " BWC ,Bandwidth Control" "Full,16,16,16,16,32,64,128,256,512,1024,2048,4096,8192,16384,32768" bitfld.long 0x00 4. " START ,Start Transfer" "Stopped,Started" textline " " bitfld.long 0x00 3. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 2. " DONEIntEn ,DONE Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " SCT ,Source Copy Transfer" "Low,High" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " DONEInt ,Transaction Done Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" rgroup asd:(0x0140+0x000C)++3 line.long 0x00 "STATUS,Channel 1 Status Register" bitfld.long 0x00 13. " DREQS ,DREQ Status" "0,1" textline " " bitfld.long 0x00 12. " NB ,Next Buffer Status Bit" "0,1" textline " " bitfld.long 0x00 11. " NFB ,Next Buffer during Transfer Programmed" "Yes,No" textline " " bitfld.long 0x00 9.--10. " EOTS ,End-of-Transfer Status" "Not requested for any descriptor,Requested for descriptor 0,Requested for descriptor 1,Requested for all descriptors" textline " " bitfld.long 0x00 7.--8. " TCS ,Terminal Count Status" "Not reached for buffer descriptor 0 & 1,Not reached for buffer descriptor only for 0,Not reached for buffer descriptor only for 1,Reached for all" textline " " bitfld.long 0x00 6. " DONE ,Transfer Completed Succefully" "Not succesfully,Succefully" textline " " bitfld.long 0x00 4.--5. " CurrentState[4:3] ,M2M Buffer FSM" "NO_BUF,BUF_ON,BUF_NEXT,?..." textline " " bitfld.long 0x00 1.--3. " CurrentState[2:0] ,M2M Channel Control FSM" "IDLE,STALL,MEM_RD,MEM_WR,BWC_WAIT,?..." textline " " bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" group asd:(0x0140+0x0010)++0x0F line.long 0x00 "BCR0,Channel Byte Count Register 0" hexmask.long.word 0x00 0.--15. 1. " BCR0 ,Channel Bytes Count" line.long 0x04 "BCR1,Channel Byte Count Register 1" hexmask.long.word 0x04 0.--15. 1. " BCR0 ,Channel Bytes Count" line.long 0x08 "SAR_BASE0,Source Base Memory Address Register" hexfld.long 0x08 " SAR_BASE0 ,Base Memory Address" line.long 0x0C "SAR_BASE1,Source Base Memory Address Register" hexfld.long 0x0C " SAR_BASE1 ,Base Memory Address" rgroup asd:(0x0140+0x0024)++7. line.long 0x00 "SAR_CURRENT0,Source Base Memory Address Register 0" hexfld.long 0x00 " SAR_CURRENT0 ,Base Memory Address" line.long 0x04 "SAR_CURRENT1,Source Base Memory Address Register 1" hexfld.long 0x04 " SAR_CURRENT1 ,Base Memory Address" group asd:(0x0140+0x002C)++7. line.long 0x00 "DAR_BASE0,Destination Base Memory Address Register" hexfld.long 0x00 " DAR_BASE0 ,Base Memory Address" line.long 0x04 "DAR_BASE1,Destination Base Memory Address Register" hexfld.long 0x04 " DAR_BASE1 ,Base Memory Address" rgroup asd:(0x0140+0x0034)++3 line.long 0x00 "DAR_CURRENT0,Destination Base Memory Address Register 0" hexfld.long 0x00 " DAR_CURRENT0 ,Base Memory Address" rgroup asd:(0x0140+0x003C)++3 line.long 0x00 "DAR_CURRENT1,Destination Base Memory Address Register 0" hexfld.long 0x00 " DAR_CURRENT1 ,Base Memory Address" tree.end ;end include file ep9312/dma/m2m.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0200 5 tree "M2P Channel 5" group asd:0x0200++7 line.long 0x00 "CONTROL,Channel 5 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (5==0||5==2||5==4||5==6||5==8) group asd:(0x0200+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (5==1||5==3||5==5||5==7||5==9) group asd:(0x0200+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0200+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0200+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0200+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0200+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0200+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0200+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0240 4 tree "M2P Channel 4" group asd:0x0240++7 line.long 0x00 "CONTROL,Channel 4 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (4==0||4==2||4==4||4==6||4==8) group asd:(0x0240+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (4==1||4==3||4==5||4==7||4==9) group asd:(0x0240+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0240+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0240+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0240+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0240+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0240+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0240+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0280 7 tree "M2P Channel 7" group asd:0x0280++7 line.long 0x00 "CONTROL,Channel 7 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (7==0||7==2||7==4||7==6||7==8) group asd:(0x0280+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (7==1||7==3||7==5||7==7||7==9) group asd:(0x0280+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0280+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0280+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0280+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0280+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0280+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0280+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x02C0 6 tree "M2P Channel 6" group asd:0x02C0++7 line.long 0x00 "CONTROL,Channel 6 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (6==0||6==2||6==4||6==6||6==8) group asd:(0x02C0+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (6==1||6==3||6==5||6==7||6==9) group asd:(0x02C0+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x02C0+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x02C0+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x02C0+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x02C0+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x02C0+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x02C0+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0300 9 tree "M2P Channel 9" group asd:0x0300++7 line.long 0x00 "CONTROL,Channel 9 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (9==0||9==2||9==4||9==6||9==8) group asd:(0x0300+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (9==1||9==3||9==5||9==7||9==9) group asd:(0x0300+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0300+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0300+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0300+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0300+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0300+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0300+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph ;begin include file ep9312/dma/m2p.ph ;parameters: 0x0340 8 tree "M2P Channel 8" group asd:0x0340++7 line.long 0x00 "CONTROL,Channel 8 Control Register" bitfld.long 0x00 6. " ICE ,Ignore Channel Error Bit" "Not ingored,Ignored" bitfld.long 0x00 5. " ABORT ,Behaviour when NEXT and Periperal Error" "NEXT->ON,NEXT->STALL" textline " " bitfld.long 0x00 4. " ENABLE ,Channel Enable" "Disabled,Enabled" bitfld.long 0x00 3. " CHErrorIntEn ,Channel Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " NFBIntEn ,NFB Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 0. " STALLIntEn ,STALL Interrupt Enable" "Disabled,Enabled" line.long 0x04 "INTERRUPT,Interrupt Status Register" bitfld.long 0x04 3. " ChErrorInt ,Data Stream Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x04 1. " NFBInt ,New Buffer Required Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " STALLInt ,Channel Stalled Interrupt" "No interrupt,Interrupt" if (8==0||8==2||8==4||8==6||8==8) group asd:(0x0340+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT0,PORT2,PORT4,PORT6,PORT8,PORT10,PORT12,PORT14,PORT16,PORT18,Not used,Not used,Not used,Not used,Not used,Not used" elif (8==1||8==3||8==5||8==7||8==9) group asd:(0x0340+0x0008)++3 line.long 0x00 "PPALLOC,Peripheral Port Allocation" bitfld.long 0x00 0.--3. " PPALLOC ,Port Allocation" "PORT1,PORT3,PORT5,PORT7,PORT9,PORT11,PORT13,PORT15,PORT17,PORT19,Not used,Not used,Not used,Not used,Not used,Not used" endif rgroup asd:(0x0340+0x000C)++3 line.long 0x00 "STATUS,Channel Status Register" hexmask.long.byte 0x00 7.--11. 1. " BYTES ,Nuber of Valid DMA Data" bitfld.long 0x00 6. " NextBuffer ,Next Free Buffer for Update" "MAXCNT0/BASE0,MAXCNT1/BASE1" textline " " bitfld.long 0x00 4.--5. " CurrentState ,Current Channel State" "IDLE,STALL,ON,NEXT" bitfld.long 0x00 3. " ChError ,Buffer Transfer Error" "No error,Error" textline " " bitfld.long 0x00 1. " NFB ,Channel FSM Moved from NEXT to ON" "Not in ON,In ON" bitfld.long 0x00 0. " STALL ,Channel Stalled" "Not stalled,Stalled" rgroup asd:(0x0340+0x0014)++3 line.long 0x00 "REMAIN,Channel Bytes Remaining Register" hexmask.long.word 0x00 0.--15. 1. " REMAIN ,Bytes Remaining" group asd:(0x0340+0x0020)++7 line.long 0x00 "MAXCNT0,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT0 ,Byte Count" line.long 0x04 "BASE0,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE0 ,Base Address" rgroup asd:(0x0340+0x0028)++3 line.long 0x00 "CURRENT0,Channel Current Address Register" hexfld.long 0x00 " CURRENT0 ,Current Address" group asd:(0x0340+0x0030)++7 line.long 0x00 "MAXCNT1,Maximum Byte Count Register" hexmask.long.word 0x00 0.--15. 1. " MAXCNT1 ,Byte Count" line.long 0x04 "BASE1,Base Address for Current and Next DMA Transfer" hexfld.long 0x00 " BASE1 ,Base Address" rgroup asd:(0x0340+0x0038)++3 line.long 0x00 "CURRENT1,Channel Current Address Register" hexfld.long 0x00 " CURRENT1 ,Current Address" tree.end ;end include file ep9312/dma/m2p.ph textline "" ;begin include file ep9312/dma/global.ph ;parameters: group asd:0x0380++3 line.long 0x00 "DMAChArb,DMA Channel Arbitration Register" bitfld.long 0x00 11. " D11 ,M2M Channel 1 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 10. " D10 ,M2M Channel 0 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 9. " D9 ,M2P Channel 8 Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x00 8. " D8 ,M2P Channel 9 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 7. " D7 ,M2P Channel 6 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 6. " D6 ,M2P Channel 7 Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x00 5. " D5 ,M2P Channel 4 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 4. " D4 ,M2P Channel 5 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 3. " D3 ,M2P Channel 2 Interrupt" "No interrupt,Interrupt" textline " " bitfld.long 0x00 2. " D2 ,M2P Channel 3 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 1. " D1 ,M2P Channel 0 Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 0. " D0 ,M2P Channel 1 Interrupt" "No interrupt,Interrupt" group asd:0x03C0++3 line.long 0x00 "DMAGIInt,DMA Global Interrupt Register" bitfld.long 0x00 0. " CHARB ,DMA Channel Arbitration" "Normal,Reversed" ;end include file ep9312/dma/global.ph ;end include file ep9312/dma.ph tree.end tree "Universal Serial Bus Controller (USB)" base asd:0x80020000 ;begin include file ep9312/usb.ph ;parameters: width 20. 8. rgroup asd:0x0000++3 line.long 0x00 "HcRevision,Revision of OHCI Specification Register" hexmask.long.byte 0x00 0.--7. 1. " REV ,HCI Specification Revision" group asd:0x0004++0x13 line.long 0x00 "HcControl,Host Controller Operating Modes Register" bitfld.long 0x00 10. " RWE ,Remote Wakeup Enable" "Disabled,Enabled" bitfld.long 0x00 9. " RWC ,Remote Wakeup Connected" "Not connected,Connected" bitfld.long 0x00 8. " IR ,Interrupt Routing" "Not routed,Routed" textline " " bitfld.long 0x00 6.--7. " HCFS ,Host Controller Functional State" "USBRESET,USBRESUME,USBOPERATIONAL,USBSUSPEND" bitfld.long 0x00 5. " BLE ,Bulk List Enable" "Disabled,Enabled" bitfld.long 0x00 4. " CLE ,Control List Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " IE ,Isochronous Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PLE ,Periodic List Enable" "Disabled,Enabled" bitfld.long 0x00 0.--1. " CBSR ,Control Bulk Service Ratio" "1:1,2:1,3:1,4:1" line.long 0x04 "HcCommandStatus,Host Controller Status Register" bitfld.long 0x04 16.--17. " SOC ,Scheduling Overrun Count" "00,01,10,11" bitfld.long 0x04 3. " OCR ,Ownership Change Request" "Not requested,Requested" bitfld.long 0x04 2. " BLF ,Bulk List Filled" "Not filled,Filled" textline " " bitfld.long 0x04 1. " CLF ,Control List Filled" "Not filled,Filled" bitfld.long 0x04 0. " HCR ,Host Controller Reset" "No reset,Reset" line.long 0x08 "HcInterruptStatus,Host Controller Interrupt Status Information Register" bitfld.long 0x08 30. " OC ,Ownership Change" "Not changed,Changed" bitfld.long 0x08 6. " RSHC ,Root Hub Status Change" "Not changed,Changed" bitfld.long 0x08 5. " FNO ,Frame Number Overflow" "Not overflowed,Overflowed" textline " " bitfld.long 0x08 4. " UE ,Unrecoverable Error" "No error,Error" bitfld.long 0x08 3. " RD ,Resume Detected" "Not detected,Detected" bitfld.long 0x08 2. " SF ,Start of Frame" "Not started,Started" textline " " bitfld.long 0x08 1. " WDH ,Writeback Done Head" "Clear,HC written" bitfld.long 0x08 0. " SO ,Scheduling Overrun" "Not overruned,Overruned" line.long 0x0C "HcInterruptEnable,Host Controller Interrupt Enable Register" bitfld.long 0x0C 31. " MIE ,Master Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 30. " OC ,Ownership Change Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 6. " RSHC ,Root Hub Status Change Interrupt Enable" "No effect,Enabled" textline " " bitfld.long 0x0C 5. " FNO ,Frame Number Overflow Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 4. " UE ,Unrecoverable Error Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 3. " RD ,Resume Detected Interrupt Enable" "No effect,Enabled" textline " " bitfld.long 0x0C 2. " SF ,Start of Frame Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 1. " WDH ,Writeback Done Head Interrupt Enable" "No effect,Enabled" bitfld.long 0x0C 0. " SO ,Scheduling Overrun Interrupt Enable" "No effect,Enabled" line.long 0x10 "HcInterruptDisable,Host Controller Interrupt Disable Register" bitfld.long 0x10 31. " MIE ,Master Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 30. " OC ,Ownership Change Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 6. " RSHC ,Root Hub Status Change Interrupt Disable" "No effect,Disabled" textline " " bitfld.long 0x10 5. " FNO ,Frame Number Overflow Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 4. " UE ,Unrecoverable Error Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 3. " RD ,Resume Detected Interrupt Disable" "No effect,Disabled" textline " " bitfld.long 0x10 2. " SF ,Start of Frame Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 1. " WDH ,Writeback Done Head Interrupt Disable" "No effect,Disabled" bitfld.long 0x10 0. " SO ,Scheduling Overrun Interrupt Disable" "No effect,Disabled" group asd:0x0018++0x1B line.long 0x00 "HcHCCA,Host Controller Communication Area Register" hexmask.long.tbyte 0x00 8.--31. 1. " AD ,Base Physical Address of Host Communication Area" line.long 0x04 "HcPeriodCurrentED,Current Endpoint Descriptor Register" hexmask.long.long 0x04 4.--31. 1. " AD ,Period Current ED Value" line.long 0x08 "HcControlHeadED,First Endpoint Descriptor of the Control List Register" hexmask.long.long 0x08 4.--31. 1. " AD ,Control Head ED Value" line.long 0x0C "HcControlCurrentED,Current Endpoint Descriptor of the Control List Register" hexmask.long.long 0x0C 4.--31. 1. " AD ,Control Current ED Value" line.long 0x10 "HcBulkHeadED,First Endpoint Descriptor of the Bulk List Register" hexmask.long.long 0x10 4.--31. 1. " AD ,Bulk Head ED Value" line.long 0x14 "HcBulkCurrentED,Current Endpoint Descriptor of the Bulk List Register" hexmask.long.long 0x14 4.--31. 1. " AD ,Bulk Current ED Value" line.long 0x18 "HcDoneHead,Last Completed Transfer Descriptor Register" hexmask.long.long 0x18 4.--31. 1. " AD ,Bulk Current ED Value" group asd:0x0034++0x0B line.long 0x00 "FmInterval,Time Interval in Frame Register" bitfld.long 0x00 31. " FIT ,Frame Interval Toggle" "Low,High" hexmask.long.word 0x00 16.--30. 1. " FSMPS ,FS Larges Data Packet" hexmask.long.word 0x00 0.--13. 1. " FI ,Frame Interval" line.long 0x04 "HcFmRemaining,Time Remaining Register" bitfld.long 0x04 31. " FRT ,Frame Remaining Toggle" "Low,High" hexmask.long.word 0x04 0.--13. 1. " FR ,Frame Remaining" line.long 0x08 "HcFmNumber,Timing Reference 16-bit Counter Register" hexmask.long.word 0x08 0.--15. 1. " FN ,Frame Number" group asd:0x0040++7 line.long 0x00 "HcPeriodicStart,Start Proccessing Time Register" hexmask.long.word 0x00 0.--13. 1. " PS ,Periodic Start Value" line.long 0x04 "HcHcLSTreshold,Time of LS Packet Transmission Register" hexmask.long.word 0x04 0.--11. 1. " LST ,LS Treshold" group asd:0x0048++3 line.long 0x00 "HcRhDescriptorA,Root Hub Register A" hexmask.long.byte 0x00 24.--31. 1. " P ,Power On to Power Good Time" bitfld.long 0x00 12. " NOCP ,No Overcurrent Protection" "No protection,Protected" textline " " bitfld.long 0x00 11. " OCPM ,OverCurrent Protection Mode" "All ports,Per-port" bitfld.long 0x00 10. " DT ,Device Type" "Not compound device,Reserved" textline " " bitfld.long 0x00 9. " NPS ,No Power Switching" "Power switched,Always on" bitfld.long 0x00 8. " PSM ,Power Switching Mode" "At same time,Individually" textline " " hexmask.long.byte 0x00 0.--7. 1. " NDP ,Number of Downstream Ports" group asd:0x004C++3 line.long 0x00 "HcRhDescriptorB,Root Hub Register B" bitfld.long 0x00 19. " PPCM3 ,Port Power Control Mask Bit 3" "Global switch,Per-port control" bitfld.long 0x00 18. " PPCM2 ,Port Power Control Mask Bit 2" "Global switch,Per-port control" textline " " bitfld.long 0x00 17. " PPCM1 ,Port Power Control Mask Bit 1" "Global switch,Per-port control" bitfld.long 0x00 16. " PPCM0 ,Port Power Control Mask Bit 0" "Reserved..." textline " " bitfld.long 0x00 3. " DR3 ,Device Removable Bit 3" "Removable,Not removable" bitfld.long 0x00 2. " DR2 ,Device Removable Bit 2" "Removable,Not removable" textline " " bitfld.long 0x00 1. " DR1 ,Device Removable Bit 1" "Removable,Not removable" bitfld.long 0x00 0. " DR0 ,Device Removable Bit 0" "Reserved..." rgroup asd:0x0050++3 line.long 0x00 "HcRhStatus(Read),Root Hub Status Register (Read)" bitfld.long 0x00 17. " CCIC ,Overcurrent Indicator Change" "Not changed,Changed" bitfld.long 0x00 16. " LPSC ,Read Local Power Status Change" "Low,High" textline " " bitfld.long 0x00 15. " DRWE ,Device Remote Wakeup Enable" "Disabled,Enabled" bitfld.long 0x00 1. " OCI ,Overcurrent Indicator" "No overcurrend,Overcurrend" textline " " bitfld.long 0x00 0. " LPS ,Local Power Status" "Low,High" wgroup asd:0x0050++3 line.long 0x00 "HcRhStatus(Write),Root Hub Status Register (Write)" bitfld.long 0x00 31. " CRWE ,Clear Remote Wakeup Enable" "No effect,Clear" bitfld.long 0x00 17. " CCIC ,Overcurrent Indicator Change" "No effect,Changed" textline " " bitfld.long 0x00 16. " LPSC ,Set Global Power " "No effect,Power on" bitfld.long 0x00 15. " DRWE ,Set Remote Wakeup Enable" "No effect,Enabled" textline " " bitfld.long 0x00 1. " OCI ,Overcurrent Indicator" "No overcurrend,Overcurrend" bitfld.long 0x00 0. " LPS ,Clear Globlal Power" "No effect,Clear" rgroup asd:0x0054++3 line.long 0x00 "HcRhPortStatus[1],Port 1 Control/Status Register (Read)" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change" "Not changed,Changed" bitfld.long 0x00 19. " OCIC ,Port Overcurrent Indicator Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change" "Not changed,Changed" bitfld.long 0x00 17. " PESC ,Port Enable Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change" "Not changed,Changed" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached" "Full speed,Low speed" textline " " bitfld.long 0x00 8. " PPS ,Power Port Status" "Power off,Power on" bitfld.long 0x00 4. " PRS ,Port Reset Status" "No reset,Reset" textline " " bitfld.long 0x00 3. " POCI ,Port Overcurrent Indicator" "No overcurrend,Overcurrend" bitfld.long 0x00 2. " PSS ,Port Suspend Status" "Not suspended,Suspended" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status" "Disabled,Enabled" bitfld.long 0x00 0. " CCS ,Current Connect Status" "No device,Device connected" wgroup asd:0x0054++3 line.long 0x00 "HcRhPortStatus[1],Port 1 Control/Status Register (Write)" bitfld.long 0x00 9. " LSDA ,Clear Status Change" "No effect,Clear" bitfld.long 0x00 8. " PPS ,Set Power Port" "No effect,Set" textline " " bitfld.long 0x00 4. " PRS ,Set Port Reset" "No effect,Reset" bitfld.long 0x00 3. " POCI ,Clear Suspend Status" "No effect,Clear" textline " " bitfld.long 0x00 2. " PSS ,Set Port Suspend" "No effect,Set" bitfld.long 0x00 1. " PES ,Set Port Enable" "No effect,Set" textline " " bitfld.long 0x00 0. " CCS ,Clear Port Enable" "No effect,Clear" rgroup asd:0x0058++3 line.long 0x00 "HcRhPortStatus[2],Port 2 Control/Status Register (Read)" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change" "Not changed,Changed" bitfld.long 0x00 19. " OCIC ,Port Overcurrent Indicator Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change" "Not changed,Changed" bitfld.long 0x00 17. " PESC ,Port Enable Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change" "Not changed,Changed" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached" "Full speed,Low speed" textline " " bitfld.long 0x00 8. " PPS ,Power Port Status" "Power off,Power on" bitfld.long 0x00 4. " PRS ,Port Reset Status" "No reset,Reset" textline " " bitfld.long 0x00 3. " POCI ,Port Overcurrent Indicator" "No overcurrend,Overcurrend" bitfld.long 0x00 2. " PSS ,Port Suspend Status" "Not suspended,Suspended" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status" "Disabled,Enabled" bitfld.long 0x00 0. " CCS ,Current Connect Status" "No device,Device connected" wgroup asd:0x0058++3 line.long 0x00 "HcRhPortStatus[2],Port 2 Control/Status Register (Write)" bitfld.long 0x00 9. " LSDA ,Clear Status Change" "No effect,Clear" bitfld.long 0x00 8. " PPS ,Set Power Port" "No effect,Set" textline " " bitfld.long 0x00 4. " PRS ,Set Port Reset" "No effect,Reset" bitfld.long 0x00 3. " POCI ,Clear Suspend Status" "No effect,Clear" textline " " bitfld.long 0x00 2. " PSS ,Set Port Suspend" "No effect,Set" bitfld.long 0x00 1. " PES ,Set Port Enable" "No effect,Set" textline " " bitfld.long 0x00 0. " CCS ,Clear Port Enable" "No effect,Clear" rgroup asd:0x005C++3 line.long 0x00 "HcRhPortStatus[3],Port 3 Control/Status Register (Read)" bitfld.long 0x00 20. " PRSC ,Port Reset Status Change" "Not changed,Changed" bitfld.long 0x00 19. " OCIC ,Port Overcurrent Indicator Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 18. " PSSC ,Port Suspend Status Change" "Not changed,Changed" bitfld.long 0x00 17. " PESC ,Port Enable Status Change" "Not changed,Changed" textline " " bitfld.long 0x00 16. " CSC ,Connect Status Change" "Not changed,Changed" bitfld.long 0x00 9. " LSDA ,Low Speed Device Attached" "Full speed,Low speed" textline " " bitfld.long 0x00 8. " PPS ,Power Port Status" "Power off,Power on" bitfld.long 0x00 4. " PRS ,Port Reset Status" "No reset,Reset" textline " " bitfld.long 0x00 3. " POCI ,Port Overcurrent Indicator" "No overcurrend,Overcurrend" bitfld.long 0x00 2. " PSS ,Port Suspend Status" "Not suspended,Suspended" textline " " bitfld.long 0x00 1. " PES ,Port Enable Status" "Disabled,Enabled" bitfld.long 0x00 0. " CCS ,Current Connect Status" "No device,Device connected" wgroup asd:0x005C++3 line.long 0x00 "HcRhPortStatus[3],Port 3 Control/Status Register (Write)" bitfld.long 0x00 9. " LSDA ,Clear Status Change" "No effect,Clear" bitfld.long 0x00 8. " PPS ,Set Power Port" "No effect,Set" textline " " bitfld.long 0x00 4. " PRS ,Set Port Reset" "No effect,Reset" bitfld.long 0x00 3. " POCI ,Clear Suspend Status" "No effect,Clear" textline " " bitfld.long 0x00 2. " PSS ,Set Port Suspend" "No effect,Set" bitfld.long 0x00 1. " PES ,Set Port Enable" "No effect,Set" textline " " bitfld.long 0x00 0. " CCS ,Clear Port Enable" "No effect,Clear" group asd:0x0080++3 line.long 0x00 "USBCfgCtrl,Through Software Configuration Register" bitfld.long 0x00 4. " TRCS ,Counter Select Value" "Low,High" bitfld.long 0x00 3. " TPOC3 ,Port 3 Disconnect Control" "Connected,Disconnected" textline " " bitfld.long 0x00 2. " TPOC2 ,Port 2 Disconnect Control" "Connected,Disconnected" bitfld.long 0x00 1. " TPOC1 ,Port 1 Disconnect Control" "Connected,Disconnected" group asd:0x0084++3 line.long 0x00 "USBHCISts,Host Controller Interface" bitfld.long 0x00 2. " RWU ,Host Controller Remote Wakeup" "No wakeup,Wakeup" bitfld.long 0x00 1. " MSN ,Host Controller New Frame" "No new frame,New frame" textline " " bitfld.long 0x00 0. " MBA ,Host Controller Buffer Access Indication" "Not accessing,Accessing" width 16. 8. ;end include file ep9312/usb.ph tree.end tree "Static Memory Controller" base asd:0x80080000 ;begin include file ep9312/memory.ph ;parameters: 0x0000 0 group asd:0x0000++3 line.long 0x00 "SMCBCR0,Bank Config Register 0" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph ;begin include file ep9312/memory.ph ;parameters: 0x0004 1 group asd:0x0004++3 line.long 0x00 "SMCBCR1,Bank Config Register 1" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph ;begin include file ep9312/memory.ph ;parameters: 0x0008 2 group asd:0x0008++3 line.long 0x00 "SMCBCR2,Bank Config Register 2" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph ;begin include file ep9312/memory.ph ;parameters: 0x000C 3 group asd:0x000C++3 line.long 0x00 "SMCBCR3,Bank Config Register 3" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph ;begin include file ep9312/memory.ph ;parameters: 0x0018 6 group asd:0x0018++3 line.long 0x00 "SMCBCR6,Bank Config Register 6" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph ;begin include file ep9312/memory.ph ;parameters: 0x001C 7 group asd:0x001C++3 line.long 0x00 "SMCBCR7,Bank Config Register 7" bitfld.long 0x00 30. " EBIBRKDIS ,EBI Break Disable" "Enabled,Disabled" bitfld.long 0x00 28.--29. " MW ,Memory Width" "8-bit,16-bit,32-bit,32-bit" bitfld.long 0x00 27. " PME ,Page Mode Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 26. " WP ,Write Protect" "SDRAM,ROM and RAM" bitfld.long 0x00 25. " WPERR ,Write Protection Error Status" "No error,Error" hexmask.long.byte 0x00 11.--15. 1. " WST2 ,Wait State 2" textline " " bitfld.long 0x00 10. " RBLE ,Read Byte Lane Enable" "Driven high,Driven low" hexmask.long.byte 0x00 5.--9. 1. " WST1 ,Wait State 1" hexmask.long.byte 0x00 0.--3. 1. " IDCY ,Idle Cycle" ;end include file ep9312/memory.ph tree.end tree "SDRAM,SyncROM and SyncFLASH Controller" base asd:0x80060000 ;begin include file ep9312/sdram.ph ;parameters: group asd:0x0004++7 line.long 0x00 "GIConfig,Global Configuration Register" bitfld.long 0x00 31. " CKE ,Synchronous Memory Clock Enable Control" "Disabled,Enabled" bitfld.long 0x00 30. " ClkShutdown ,Synchronous Memory Clock Shutdown Control" "Free running,Gated" textline " " bitfld.long 0x00 7. " ReArbEn ,Rearbitration Controller Enable" "Disabled,Enabled" bitfld.long 0x00 6. " LCR ,Load Command Register" "Clear,Set" textline " " bitfld.long 0x00 5. " SMEMBust ,Synchronous Memory Mode Register" "Idle,Busy" bitfld.long 0x00 1. " MRS ,Synchronous Memory Mode Register" "Clear,Set" textline " " bitfld.long 0x00 0. " Initialize ,Initialize Bit" "Clear,Set" line.long 0x04 "RefreshTimr,Refresh Timer Register" hexmask.long.word 0x04 0.--15. 1. " RefCnt ,Refresh Count" rgroup asd:0x000C++3 line.long 0x00 "BootSts,Boot Status" bitfld.long 0x00 2. " LatchedASDO ,Boot Media" "Asynchronous ROM,Synchronous ROM" bitfld.long 0x00 0.--1. " Width ,Boot Memory Width" "8-bit,16-bit,32-bit,32-bit" group asd:0x0010++0x0F line.long 0x00 "SDRAMDevCfg0,Device Configuration 0" bitfld.long 0x00 24. " AutoPrecharge ,Auto Precharge" "No auto,Auto" bitfld.long 0x00 20.--21. " RasToCas ,Synchronous Memory RAS to CAS Latency" "Reserved,Reserved,2,3" textline " " bitfld.long 0x00 19. " WBL ,Write Burst Length" "Low,High" bitfld.long 0x00 16.--18. " CasLat ,Synchronous Memory CAS Latency" "Reserved,2,3,4,5,6,7,8" textline " " bitfld.long 0x00 7. " SFConfigAddr ,Configuration Address Register Read" "Normal,SyncFLASH" bitfld.long 0x00 6. " 2KPAGE ,Synchronous Memory 2 KByte Page Mode" "Not 2K,2 KByte" textline " " bitfld.long 0x00 5. " SROMLL ,SROM Lookalike Mode" "Clear,Set" bitfld.long 0x00 4. " SROM512 ,SROM Maximum Burst Size=512" "Not 512 depth,Depth 512" textline " " bitfld.long 0x00 3. " BankCount ,Bank Count" "Two-bank,Four-bank" bitfld.long 0x00 2. " ExtBusWidth ,External Bus Width" "32-bits,16-bits" line.long 0x04 "SDRAMDevCfg1,Device Configuration 1" bitfld.long 0x04 24. " AutoPrecharge ,Auto Precharge" "No auto,Auto" bitfld.long 0x04 20.--21. " RasToCas ,Synchronous Memory RAS to CAS Latency" "Reserved,Reserved,2,3" textline " " bitfld.long 0x04 19. " WBL ,Write Burst Length" "Low,High" bitfld.long 0x04 16.--18. " CasLat ,Synchronous Memory CAS Latency" "Reserved,2,3,4,5,6,7,8" textline " " bitfld.long 0x04 7. " SFConfigAddr ,Configuration Address Register Read" "Normal,SyncFLASH" bitfld.long 0x04 6. " 2KPAGE ,Synchronous Memory 2 KByte Page Mode" "Not 2K,2 KByte" textline " " bitfld.long 0x04 5. " SROMLL ,SROM Lookalike Mode" "Clear,Set" bitfld.long 0x04 4. " SROM512 ,SROM Maximum Burst Size=512" "Not 512 depth,Depth 512" textline " " bitfld.long 0x04 3. " BankCount ,Bank Count" "Two-bank,Four-bank" bitfld.long 0x04 2. " ExtBusWidth ,External Bus Width" "32-bits,16-bits" line.long 0x08 "SDRAMDevCfg2,Device Configuration 2" bitfld.long 0x08 24. " AutoPrecharge ,Auto Precharge" "No auto,Auto" bitfld.long 0x08 20.--21. " RasToCas ,Synchronous Memory RAS to CAS Latency" "Reserved,Reserved,2,3" textline " " bitfld.long 0x08 19. " WBL ,Write Burst Length" "Low,High" bitfld.long 0x08 16.--18. " CasLat ,Synchronous Memory CAS Latency" "Reserved,2,3,4,5,6,7,8" textline " " bitfld.long 0x08 7. " SFConfigAddr ,Configuration Address Register Read" "Normal,SyncFLASH" bitfld.long 0x08 6. " 2KPAGE ,Synchronous Memory 2 KByte Page Mode" "Not 2K,2 KByte" textline " " bitfld.long 0x08 5. " SROMLL ,SROM Lookalike Mode" "Clear,Set" bitfld.long 0x08 4. " SROM512 ,SROM Maximum Burst Size=512" "Not 512 depth,Depth 512" textline " " bitfld.long 0x08 3. " BankCount ,Bank Count" "Two-bank,Four-bank" bitfld.long 0x08 2. " ExtBusWidth ,External Bus Width" "32-bits,16-bits" line.long 0x0C "SDRAMDevCfg3,Device Configuration 3" bitfld.long 0x0C 24. " AutoPrecharge ,Auto Precharge" "No auto,Auto" bitfld.long 0x0C 20.--21. " RasToCas ,Synchronous Memory RAS to CAS Latency" "Reserved,Reserved,2,3" textline " " bitfld.long 0x0C 19. " WBL ,Write Burst Length" "Low,High" bitfld.long 0x0C 16.--18. " CasLat ,Synchronous Memory CAS Latency" "Reserved,2,3,4,5,6,7,8" textline " " bitfld.long 0x0C 7. " SFConfigAddr ,Configuration Address Register Read" "Normal,SyncFLASH" bitfld.long 0x0C 6. " 2KPAGE ,Synchronous Memory 2 KByte Page Mode" "Not 2K,2 KByte" textline " " bitfld.long 0x0C 5. " SROMLL ,SROM Lookalike Mode" "Clear,Set" bitfld.long 0x0C 4. " SROM512 ,SROM Maximum Burst Size=512" "Not 512 depth,Depth 512" textline " " bitfld.long 0x0C 3. " BankCount ,Bank Count" "Two-bank,Four-bank" bitfld.long 0x0C 2. " ExtBusWidth ,External Bus Width" "32-bits,16-bits" ;end include file ep9312/sdram.ph tree.end tree "UART1 With HDLC and Modem Control Signals" base asd:0x808C0000 ;begin include file ep9312/uart1.ph ;parameters: width 20. 8. tree "UART Registers" group asd:0x0000++0x17 line.long 0x00 "UART1Data,UART1 Data Register" hexmask.long.byte 0x00 0.--7. 1. " DATA ,UART Data" line.long 0x04 "UART1RXSts,UART1 Receive Status Register/Error Clear Register" bitfld.long 0x04 3. " OE ,Overrun Error" "No error,Error" bitfld.long 0x04 2. " BE ,Break Error" "No error,Error" textline " " bitfld.long 0x04 1. " PE ,Parity Error" "No error,Error" bitfld.long 0x04 0. " FE ,Framing Error" "No error,Error" line.long 0x08 "UART1LinCtrlHigh,UART1 Line Control Register High" bitfld.long 0x08 5.--6. " WLEN ,Number of Bits per Frame" "5 bits,6 bits,7 bits,8 bits" bitfld.long 0x08 4. " FEN ,FIFO Enable" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " STP2 ,Two Stop Bits Select" "One bit,Two bits" bitfld.long 0x08 2. " EPS ,Even Parity Select" "Odd,Even" textline " " bitfld.long 0x08 1. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.long 0x08 0. " BRK ,Send Break" "Normal,Output low" line.long 0x0C "UART1LinCtrlMid,UART1 Line Control Register Middle" hexmask.long.byte 0x0C 0.--7. 1. " BR ,Baud Rate Divisior Bits 15-8" line.long 0x10 "UART1LinCtrlLow,UART1 Line Control Register Low" hexmask.long.byte 0x10 0.--7. 1. " BR ,Baud Rate Divisior 7-0" line.long 0x14 "UART1Ctrl,UART1 Control Register" bitfld.long 0x14 7. " LBE ,Loopback Enable" "Disabled,Enabled" bitfld.long 0x14 6. " RTIE ,Receive Timeout" "Disabled,Enabled" textline " " bitfld.long 0x14 5. " TIE ,Transmit Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 4. " RIE ,Receive Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " MSIE ,Modem Status Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 0. " UARTE ,UART Enable" "Disabled,Enabled" rgroup asd:0x0018++3 line.long 0x00 "UART1Flag,UART1 Flag Register" bitfld.long 0x00 7. " TXFE ,Transmit FIFO Empty" "Not empty,Empty" bitfld.long 0x00 6. " RXFF ,Receive FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 5. " TXFF ,Transmit FIFO Full" "Not full,Full" bitfld.long 0x00 4. " RXFE ,Receive FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 3. " BUSY ,UART Busy" "Not busy,Busy" bitfld.long 0x00 2. " DCD ,Data Carrier Detect Status" "Clear,Set" textline " " bitfld.long 0x00 1. " DSR ,Data Set Ready Status" "Not ready,Ready" bitfld.long 0x00 0. " CTS ,Clear To Send Status" "Not clear,Clear" group asd:0x001C++3 line.long 0x00 "UART1IntIDIntClr,UART1 Interrupt Identification and Interrupt Clear Register" bitfld.long 0x00 3. " RTIS ,Receive Timeout Interrupt Status" "Clear,Set" bitfld.long 0x00 2. " TIS ,Transmit Interrupt Status" "FIFO full,FIFO not full" textline " " bitfld.long 0x00 1. " RIS ,Receive Interrupt Status" "FIFO empty,FIFO not empty" bitfld.long 0x00 0. " MIS ,Modem Interrupt Status" "Not asserted,Asserted" group asd:0x0028++3 line.long 0x00 "UART1DMACtrl,UART1 DMA Control Register" bitfld.long 0x00 2. " DMAERR ,RX DMA Error Handling Enable" "Disabled,Enabled" bitfld.long 0x00 1. " TXDMAE ,TX DMA Interface Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " RXDMAE ,RX DMA Interface Enable" "Disabled,Enabled" tree.end tree "Modem Registers" group asd:0x0100++3 line.long 0x00 "UART1ModemCtrl,UART1 Modem Control Register" bitfld.long 0x00 4. " LOOP ,Loopback Function Control" "No loopback,Loopback" bitfld.long 0x00 3. " OUT2 ,OUT2 Function" "Clear,Set" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 Function" "Clear,Set" bitfld.long 0x00 1. " RTS ,RTS Output Signal" "RTSn low,RTSn high" textline " " bitfld.long 0x00 0. " DTR ,DTR Output Signal" "DTRn low,DTRn high" rgroup asd:0x0104++3 line.long 0x00 "UART1ModemSts,UART1 Modem Status Register" bitfld.long 0x00 7. " DCD ,Inverse of DCDn Input Pin" "Not inversed,Inversed" bitfld.long 0x00 6. " RI ,Inverse of RI Input Pin" "Not inversed,Inversed" textline " " bitfld.long 0x00 5. " DSR ,Inverse of DSR Input Pin" "Not inversed,Inversed" bitfld.long 0x00 4. " CTS ,Inverse of CTS Input Pin" "Not inversed,Inversed" textline " " bitfld.long 0x00 3. " DDCD ,Delta DCD-DCDn Pin Change" "Not changed,Changed" bitfld.long 0x00 2. " TERI ,Trailing Edge Ring Indicator" "RI not changed,RI not changed" textline " " bitfld.long 0x00 1. " DDSR ,Delta DSR-DSRn Pin Change" "Not changed,Changed" bitfld.long 0x00 0. " DCTS ,Delta CTS-CTSn Pin Change" "Not changed,Changed" tree.end tree "HDLC Registers" group asd:0x020C++3 line.long 0x00 "UART1HDLCtrl,HDLC Control Register" bitfld.long 0x00 27. " CMAS ,Clock Master" "Internal,External" bitfld.long 0x00 26. " TXCM ,Transmit Clock Mode" "Do not generate,Generate" textline " " bitfld.long 0x00 25. " RXCM ,Receive Clock Mode" "Do not generate,Generate" bitfld.long 0x00 24. " TXENC ,Transmit Encoding Method" "NRZ,Manchester" textline " " bitfld.long 0x00 23. " RXENC ,Receive Encoding Method" "NRZ,Manchester" bitfld.long 0x00 22. " SYNC ,Synchronous/Asynchronous HDLC Mode" "Asynchronous,Synchronous" textline " " bitfld.long 0x00 21. " TFCEN ,Transmit Frame Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 20. " TABEN ,Transmit Frame Abort Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " RFCEN ,Receive Frame Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 18. " RILEN ,Receive Information Lost Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " RFLEN ,Receive Frame Lost Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 16. " RTOEN ,Receiver Time Out Interrupt Enable" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 12.--15. 1. " FLAG ,Minimum Number of Opening and CLosing Flags for HDLC TX" bitfld.long 0x00 11. " CRCN ,CRC Polarity Control" "CRC not inverted,CRC inverted" textline " " bitfld.long 0x00 10. " CRCApd ,CRC Pass Through" "Not passed,Passed" bitfld.long 0x00 9. " IDLE ,Idle Mode" "Mark mode,Flag mode" textline " " bitfld.long 0x00 7.--8. " AME ,Address Match Enable" "No address,4x1 byte,2x2 byte,Undefined" bitfld.long 0x00 6. " IDLSpec ,Idle in Space" "In mark,In space" textline " " bitfld.long 0x00 5. " CRCZ ,CRC Zero Seed" "All ones,All zeros" bitfld.long 0x00 4. " RXE ,HDLC Receive Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " TXE ,HDLC Transmit Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TUS ,Transmit FIFO Underrun Select" "Transmit stop,Transmit abort" textline " " bitfld.long 0x00 1. " CRCR ,CRC Enable" "Disabled,Enabled" bitfld.long 0x00 0. " CRCS ,CRC Size" "CRC-CCITT,CRC-32" group asd:0x0210++7 line.long 0x00 "UART1HDLCAddMtchVal,HDLC Address Match Register" hexfld.long 0x00 " AMV ,Address Match Value" line.long 0x04 "UART1HDLCAddMask,HDLC Address Mask Register" hexfld.long 0x04 " AMSK ,Address Mask Value" rgroup asd:0x0218++3 line.long 0x00 "UART1HDLCRXInfoBuf,HDLC Receive Information Buffer Register" bitfld.long 0x00 17. " BPLLE ,Buffer Digital PLL Error" "Not aborted,Aborted" hexmask.long.word 0x00 4.--14. 1. " BC ,Received Frame Byte Count" textline " " bitfld.long 0x00 3. " BFRE ,Buffered Framing Error" "No error,Error" bitfld.long 0x00 2. " BROR ,Buffered Receiver Over Error" "No error,Error" textline " " bitfld.long 0x00 1. " BRCE ,Buffered CRC Error" "No error,Error" bitfld.long 0x00 0. " BRAB ,Buffered Receiver Error" "No error,Error" group asd:0x021C++3 line.long 0x00 "UART1HDLCSts,HDLC Status Register" bitfld.long 0x00 17. " PLLE ,Digital PLL Error" "No error,Error" bitfld.long 0x00 16. " PLLCC ,Digital PLL Carrier Sense" "Not sensed,Sensed" textline " " bitfld.long 0x00 15. " LNKIDL ,Link Idle" "RX not changed,RX changed" bitfld.long 0x00 14. " CRE ,CRC Error" "No CRC,CRC" textline " " bitfld.long 0x00 13. " ROR ,Receive FIFO Overrun" "Not overruned,Overruned" bitfld.long 0x00 12. " TBY ,Transmitter Busy" "Not busy,Busy" textline " " bitfld.long 0x00 11. " RIF ,Receiver In Frame" "Idle,Receiving frame" bitfld.long 0x00 9. " RAB ,Receiver Abort" "Not aborted,Aborted" textline " " bitfld.long 0x00 8. " RTO ,Receiver Time Out" "Set,Clear" bitfld.long 0x00 7. " EOF ,End of Frame" "No end of frame,End of frame" textline " " bitfld.long 0x00 6. " RFL ,Receive Frame Lost" "Not lost,Lost" bitfld.long 0x00 5. " RIL ,Receive Information Buffer Lost" "Not lost,Lost" textline " " bitfld.long 0x00 4. " RFC ,Receive Frame Complete" "Not completed,Completed" bitfld.long 0x00 3. " RFS ,Receive FIFO Service Request" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " TAB ,Transmitted Frame Aborted" "Not aborted,Aborted" bitfld.long 0x00 1. " TFC ,Transmit Frame Complete" "Not completed,Completed" textline " " bitfld.long 0x00 0. " TFS ,Transmit FIFO Service Request" "FIFO full TX disabled,FIFO not full TX enabled" tree.end width 16. 8. ;end include file ep9312/uart1.ph tree.end tree "UART2" base asd:0x808D0000 ;begin include file ep9312/uart2.ph ;parameters: width 18. 8. group asd:0x0000++0x17 line.long 0x00 "UART2Data,UART Data Register" hexmask.long.byte 0x00 0.--7. 1. " DATA ,UART Data" line.long 0x04 "UART2RXSts,UART Receive Status Register aand Error Clear Register" bitfld.long 0x04 3. " OE ,Overrun Error" "No error,Error" bitfld.long 0x04 2. " BE ,Break Error" "No error,Error" textline " " bitfld.long 0x04 1. " PE ,Parity Error" "No error,Error" bitfld.long 0x04 0. " FE ,Framing Error" "No error,Error" line.long 0x08 "UART2LinCtrlHigh,UART Line Control High Register" bitfld.long 0x08 5.--6. " WLEN ,Number of Bits per Frame" "5 bits,6 bits,7 bits,8 bits" bitfld.long 0x08 4. " FEN ,FIFO Enable" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " STP2 ,Two Stop Bits Select" "One bit,Two bits" bitfld.long 0x08 2. " EPS ,Even Parity Select" "Odd,Even" textline " " bitfld.long 0x08 1. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.long 0x08 0. " BRK ,Send Break" "Normal,Output low" line.long 0x0C "UART2LinCtrlMid,UART Line Control Midle Register" hexmask.long.byte 0x0C 0.--7. 1. " BR ,Baud Rate Divisior 15-8" line.long 0x10 "UART2LinCtrlLow,UART Line Control Low Register" hexmask.long.byte 0x10 0.--7. 1. " BR ,Baud Rate Divisior 7-0" line.long 0x14 "UART2Ctrl,UART Control Register" bitfld.long 0x14 7. " LBE ,Loopback Enable" "Disabled,Enabled" bitfld.long 0x14 6. " RTIE ,Receive Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x14 5. " TIE ,Transmit Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 4. " RIE ,Receive Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " MSIE ,Modem Status Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 2. " SIRLP ,SIR Low Power Mode" "Normal,Low power" textline " " bitfld.long 0x14 1. " SIEN ,SIE Enable" "Disabled,Enabled" bitfld.long 0x14 0. " UARTE ,UART Enable" "Disabled,Enabled" rgroup asd:0x0018++3 line.long 0x00 "UART2Flag,UART Flag Register" bitfld.long 0x00 7. " TXFE ,Transmit FIFO Empty" "Not empty,Empty" bitfld.long 0x00 6. " RXFF ,Receive FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 5. " TXFF ,Transmit FIFO Full" "Not full,Full" bitfld.long 0x00 4. " RXFE ,Receive FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 3. " BUSY ,UART Busy" "Not busy,Busy" bitfld.long 0x00 2. " DCD ,Data Carrier Detect Status" "Clear,Set" textline " " bitfld.long 0x00 1. " DSR ,Data Set Ready Status" "Not ready,Ready" bitfld.long 0x00 0. " CTS ,Clear To Send Status" "Not clear,Clear" group asd:0x001C++3 line.long 0x00 "UART1IntIDIntClr,UART1 Interrupt Identification and Interrupt Clear Register" bitfld.long 0x00 3. " RTIS ,Receive Timeout Interrupt Status" "Clear,Set" bitfld.long 0x00 2. " TIS ,Transmit Interrupt Status" "FIFO full,FIFO not full" textline " " bitfld.long 0x00 1. " RIS ,Receive Interrupt Status" "FIFO empty,FIFO not empty" bitfld.long 0x00 0. " MIS ,Modem Interrupt Status" "Not asserted,Asserted" group asd:0x0020++0x0B line.long 0x00 "UART2IrLowPwrCntr,UART IrDA Low Power Divisior Register" hexmask.long.byte 0x00 0.--7. 1. " ILPDV ,IrDA Low Power Divisior Bits" line.long 0x04 "UART2DMACtrl,UART DMA Control Register" bitfld.long 0x04 2. " DMAERR ,RX DMA Error Handling Enable" "Disabled,Enabled" bitfld.long 0x04 1. " TXDMAE ,TX DMA Interface Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " RXDMAE ,RX DMA Interface Enable" "Disabled,Enabled" line.long 0x08 "UART2TMR,UART SIR Loopback Register" bitfld.long 0x08 1. " SIRTEST ,SIR Test Enable" "Disabled,Enabled" ;end include file ep9312/uart2.ph tree.end tree "UART3 with HDLC Encoder" base asd:0x808E0000 ;begin include file ep9312/uart3.ph ;parameters: width 20. 8. tree "UART Registers" group asd:0x0000++0x17 line.long 0x00 "UART3Data,UART3 Data Register" hexmask.long.byte 0x00 0.--7. 1. " DATA ,UART Data" line.long 0x04 "UART3RXSts,UART3 Receive Status Register/Error Clear Register" bitfld.long 0x04 3. " OE ,Overrun Error" "No error,Error" bitfld.long 0x04 2. " BE ,Break Error" "No error,Error" textline " " bitfld.long 0x04 1. " PE ,Parity Error" "No error,Error" bitfld.long 0x04 0. " FE ,Framing Error" "No error,Error" line.long 0x08 "UART3LinCtrlHigh,UART3 Line Control Register High" bitfld.long 0x08 5.--6. " WLEN ,Number of Bits per Frame" "5 bits,6 bits,7 bits,8 bits" bitfld.long 0x08 4. " FEN ,FIFO Enable" "Disabled,Enabled" textline " " bitfld.long 0x08 3. " STP2 ,Two Stop Bits Select" "One bit,Two bits" bitfld.long 0x08 2. " EPS ,Even Parity Select" "Odd,Even" textline " " bitfld.long 0x08 1. " PEN ,Parity Enable" "Disabled,Enabled" bitfld.long 0x08 0. " BRK ,Send Break" "Normal,Output low" line.long 0x0C "UART3LinCtrlMid,UART3 Line Control Register Middle" hexmask.long.byte 0x0C 0.--7. 1. " BR ,Baud Rate Divisior Bits 15-8" line.long 0x10 "UART3LinCtrlLow,UART3 Line Control Register Low" hexmask.long.byte 0x10 0.--7. 1. " BR ,Baud Rate Divisior 7-0" line.long 0x14 "UART3Ctrl,UART3 Control Register" bitfld.long 0x14 7. " LBE ,Loopback Enable" "Disabled,Enabled" bitfld.long 0x14 6. " RTIE ,Receive Timeout" "Disabled,Enabled" textline " " bitfld.long 0x14 5. " TIE ,Transmit Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 4. " RIE ,Receive Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x14 3. " MSIE ,Modem Status Interrupt Enable" "Disabled,Enabled" bitfld.long 0x14 0. " UARTE ,UART Enable" "Disabled,Enabled" rgroup asd:0x0018++3 line.long 0x00 "UART3Flag,UART3 Flag Register" bitfld.long 0x00 7. " TXFE ,Transmit FIFO Empty" "Not empty,Empty" bitfld.long 0x00 6. " RXFF ,Receive FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 5. " TXFF ,Transmit FIFO Full" "Not full,Full" bitfld.long 0x00 4. " RXFE ,Receive FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 3. " BUSY ,UART Busy" "Not busy,Busy" bitfld.long 0x00 2. " DCD ,Data Carrier Detect Status" "Clear,Set" textline " " bitfld.long 0x00 1. " DSR ,Data Set Ready Status" "Not ready,Ready" bitfld.long 0x00 0. " CTS ,Clear To Send Status" "Not clear,Clear" group asd:0x001C++3 line.long 0x00 "UART3IntIDIntClr,UART3 Interrupt Identification and Interrupt Clear Register" bitfld.long 0x00 3. " RTIS ,Receive Timeout Interrupt Status" "Clear,Set" bitfld.long 0x00 2. " TIS ,Transmit Interrupt Status" "FIFO full,FIFO not full" textline " " bitfld.long 0x00 1. " RIS ,Receive Interrupt Status" "FIFO empty,FIFO not empty" bitfld.long 0x00 0. " MIS ,Modem Interrupt Status" "Not asserted,Asserted" group asd:0x0020++3 line.long 0x00 "UART3LowPwrCntr,UART3 IrDA Low Power Divisior Register" group asd:0x0028++3 line.long 0x00 "UART3DMACtrl,UART3 DMA Control Register" bitfld.long 0x00 2. " DMAERR ,RX DMA Error Handling Enable" "Disabled,Enabled" bitfld.long 0x00 1. " TXDMAE ,TX DMA Interface Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " RXDMAE ,RX DMA Interface Enable" "Disabled,Enabled" group asd:0x0100++3 line.long 0x00 "UART3ModemCtrl,UART3 Modem Control Register" bitfld.long 0x00 3. " OUT2 ,OUT2 Function" "TENn Driven by UART3Flag,TENn Controlled by OUT1" textline " " bitfld.long 0x00 2. " OUT1 ,OUT1 Function" "TENn=OUT1,Ignored" group asd:0x0104++7 line.long 0x00 "UART3ModemSts,UART3 Modem Status Register" line.long 0x04 "UART3ModemTstCtrl,UART3 Modem Support Test Control Register" tree.end tree "HDLC Registers" group asd:0x020C++3 line.long 0x00 "UART1HDLCtrl,HDLC Control Register" bitfld.long 0x00 27. " CMAS ,Clock Master" "Internal,External" bitfld.long 0x00 26. " TXCM ,Transmit Clock Mode" "Do not generate,Generate" textline " " bitfld.long 0x00 25. " RXCM ,Receive Clock Mode" "Do not generate,Generate" bitfld.long 0x00 24. " TXENC ,Transmit Encoding Method" "NRZ,Manchester" textline " " bitfld.long 0x00 23. " RXENC ,Receive Encoding Method" "NRZ,Manchester" bitfld.long 0x00 22. " SYNC ,Synchronous/Asynchronous HDLC Mode" "Asynchronous,Synchronous" textline " " bitfld.long 0x00 21. " TFCEN ,Transmit Frame Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 20. " TABEN ,Transmit Frame Abort Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 19. " RFCEN ,Receive Frame Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 18. " RILEN ,Receive Information Lost Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 17. " RFLEN ,Receive Frame Lost Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 16. " RTOEN ,Receiver Time Out Interrupt Enable" "Disabled,Enabled" textline " " hexmask.long.byte 0x00 12.--15. 1. " FLAG ,Minimum Number of Opening and CLosing Flags for HDLC TX" bitfld.long 0x00 11. " CRCN ,CRC Polarity Control" "CRC not inverted,CRC inverted" textline " " bitfld.long 0x00 10. " CRCApd ,CRC Pass Through" "Not passed,Passed" bitfld.long 0x00 9. " IDLE ,Idle Mode" "Mark mode,Flag mode" textline " " bitfld.long 0x00 7.--8. " AME ,Address Match Enable" "No address,4x1 byte,2x2 byte,Undefined" bitfld.long 0x00 4. " RXE ,HDLC Receive Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 3. " TXE ,HDLC Transmit Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TUS ,Transmit FIFO Underrun Select" "Transmit stop,Transmit abort" textline " " bitfld.long 0x00 1. " CRCR ,CRC Enable" "Disabled,Enabled" bitfld.long 0x00 0. " CRCS ,CRC Size" "CRC-CCITT,CRC-32" group asd:0x0210++7 line.long 0x00 "UART1HDLCAddMtchVal,HDLC Address Match Register" hexfld.long 0x00 " AMV ,Address Match Value" line.long 0x04 "UART1HDLCAddMask,HDLC Address Mask Register" hexfld.long 0x04 " AMSK ,Address Mask Value" rgroup asd:0x0218++3 line.long 0x00 "UART1HDLCRXInfoBuf,HDLC Receive Information Buffer Register" hexmask.long.word 0x00 4.--14. 1. " BC ,Received Frame Byte Count" bitfld.long 0x00 3. " BFRE ,Buffered Framing Error" "No error,Error" textline " " bitfld.long 0x00 2. " BROR ,Buffered Receiver Over Error" "No error,Error" bitfld.long 0x00 1. " BRCE ,Buffered CRC Error" "No error,Error" textline " " bitfld.long 0x00 0. " BRAB ,Buffered Receiver Error" "No error,Error" group asd:0x021C++3 line.long 0x00 "UART1HDLCSts,HDLC Status Register" bitfld.long 0x00 14. " CRE ,CRC Error" "No CRC,CRC" bitfld.long 0x00 13. " ROR ,Receive FIFO Overrun" "Not overruned,Overruned" textline " " bitfld.long 0x00 12. " TBY ,Transmitter Busy" "Not busy,Busy" bitfld.long 0x00 11. " RIF ,Receiver In Frame" "Idle,Receiving frame" textline " " bitfld.long 0x00 9. " RAB ,Receiver Abort" "Not aborted,Aborted" bitfld.long 0x00 8. " RTO ,Receiver Time Out" "Set,Clear" textline " " bitfld.long 0x00 7. " EOF ,End of Frame" "No end of frame,End of frame" bitfld.long 0x00 6. " RFL ,Receive Frame Lost" "Not lost,Lost" textline " " bitfld.long 0x00 5. " RIL ,Receive Information Buffer Lost" "Not lost,Lost" bitfld.long 0x00 4. " RFC ,Receive Frame Complete" "Not completed,Completed" textline " " bitfld.long 0x00 3. " RFS ,Receive FIFO Service Request" "Disabled,Enabled" bitfld.long 0x00 2. " TAB ,Transmitted Frame Aborted" "Not aborted,Aborted" textline " " bitfld.long 0x00 1. " TFC ,Transmit Frame Complete" "Not completed,Completed" bitfld.long 0x00 0. " TFS ,Transmit FIFO Service Request" "FIFO full TX disabled,FIFO not full TX enabled" tree.end width 16. 8. ;end include file ep9312/uart3.ph tree.end tree "IrDA" base asd:0x808B0000 ;begin include file ep9312/irda.ph ;parameters: group asd:0x0000++0x0B line.long 0x00 "IrEnable,IrDA Enable Register" bitfld.long 0x00 4. " FD ,Fast Done Status" "Not done,Done" bitfld.long 0x00 3. " MD ,Medium Done Status" "Not done,Done" textline " " bitfld.long 0x00 2. " LBM ,Loopback Mode" "Normal,Loopback" bitfld.long 0x00 0.--1. " EN ,Enable Value" "No encoder,SIR,MIR,FIR" line.long 0x04 "IrCtrl,IrDA Control Register" bitfld.long 0x04 7. " AME ,Address Match Enable" "Disabled,Enabled" bitfld.long 0x04 6. " RXP ,Receve Polarity Control" "Not inverted,Inverted" textline " " bitfld.long 0x04 5. " TXP ,Transmit Polarity Control" "Not inverted,Inverted" bitfld.long 0x04 4. " RXE ,Receiver Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " TXE ,Transmit Enable" "Disabled,Enabled" bitfld.long 0x04 2. " TUS ,Transmit Buffer Underrun Select" "Causes stop flag,Causes abort" textline " " bitfld.long 0x04 1. " BRD ,MIR Bit Rate Select" "0.576Mbit/s,1.152Mbit/s" line.long 0x08 "IrAdrMatchVal,IrDA Address Match Value Register" hexmask.long.word 0x08 0.--7. 1. " AMV , Address Match Value" rgroup asd:0x000C++3 line.long 0x00 "IrFlag,IrDA Flag Register" bitfld.long 0x00 9. " TBY ,Transmitter Busy Flag" "Not busy,Busy" bitfld.long 0x00 8. " RIF ,Receive In Frame" "In preamble/start,In frame" textline " " bitfld.long 0x00 7. " RSY ,Receiver Synchronized Flag" "Hunt mode,Sychronized" bitfld.long 0x00 6. " EOF ,End of Frame" "Frame not completed,Frame completed" textline " " bitfld.long 0x00 4.--5. " WST ,Width Status" "All valid,Least byte,Least two,Least three" bitfld.long 0x00 3. " FRE ,FIR Framing Error" "No error,Error" textline " " bitfld.long 0x00 2. " ROR ,Receive Buffer Overrun" "Not overruned,Overruned" bitfld.long 0x00 1. " CRE ,CRC Error" "No error,Error" textline " " bitfld.long 0x00 0. " RAB ,Receiver Abort" "Not aborted,Aborted" group asd:0x0010++3 line.long 0x00 "IrData,IrDA Data Register" hexfld.long 0x00 " DATA ,IrDA Data Word" wgroup asd:0x0014++0x0B line.long 0x00 "IrDataTail,IrDA Data Tail Register" hexfld.long 0x00 " DATA ,IrDA Transmit Payload Data" line.long 0x04 "IrDataTail,IrDA Data Tail Register" hexfld.long 0x04 " DATA ,IrDA Transmit Payload Data" line.long 0x08 "IrDataTail,IrDA Data Tail Register" hexfld.long 0x08 " DATA ,IrDA Transmit Payload Data" rgroup asd:0x0020++7 line.long 0x00 "IrRIB,IrDA Receive Information Register" hexmask.long.word 0x00 4.--14. 1. " BC ,Received Frame Byte Count" bitfld.long 0x00 3. " BFRE ,Buffered Framing Error" "No error,Error" textline " " bitfld.long 0x00 2. " BROR ,Buffered Receiver Over Error" "No error,Error" bitfld.long 0x00 1. " BRCE ,Buffered CRC Error" "No error,Error" textline " " bitfld.long 0x00 0. " BRAB ,Buffered Receiver Error" "No error,Error" line.long 0x04 "IrTR0,IrDA Test Register 0" hexmask.long.word 0x04 0.--10. 1. " BC ,Byte Count" group asd:0x0028++3 line.long 0x00 "IrDMACR,IrDA DMA Control Register" bitfld.long 0x00 2. " DMAERR ,RX DMA Error Handling Enable" "Disabled,Enabled" bitfld.long 0x00 1. " TXDAE ,TX DMA Interface Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " RXDMAE ,RX DMA Interface Enable" "Disabled,Enabled" group asd:0x0030++3 line.long 0x00 "SIRTR0,IrDA Slow InfraRed Test Register 0" bitfld.long 0x00 7. " SIREN ,State of SIERN After Synchronization" "Low,High" bitfld.long 0x00 6. " SIROUT ,State of SIROUT" "Low,High" textline " " bitfld.long 0x00 5. " TXD ,State of TXD Input" "Low,High" bitfld.long 0x00 4. " RXD ,State of RXD Input" "Low,High" textline " " bitfld.long 0x00 3. " SIRT ," "0,1" bitfld.long 0x00 2. " SIRIN ," "0,1" textline " " bitfld.long 0x00 1. " S16CLK ," "0,1" bitfld.long 0x00 0. " TSIRC ," "0,1" group asd:0x0080++7 line.long 0x00 "MISR,MIR Status Register" bitfld.long 0x00 6. " RFL ,Receive Frame Lost" "Not lost,Lost" bitfld.long 0x00 5. " RIL ,Receive Information Buffer Lost" "Not lost,Lost" textline " " bitfld.long 0x00 4. " RFC ,Receive Frame Complete" "Not completed,Completed" bitfld.long 0x00 3. " RFS ,Reveive Buffer Service Request" "Not requested,Requested" textline " " bitfld.long 0x00 2. " TAB ,Transmit Frame Aborted" "Not aborted,Aborted" bitfld.long 0x00 1. " TFC ,Transmit Frame Complete" "Not completed,Completed" textline " " bitfld.long 0x00 0. " TFS ,Transmit Buffer Service Request" "Not requested,Requested" line.long 0x04 "MIMR,MIR Interrupt Mask Register" bitfld.long 0x04 6. " RFL ,RFL Mask Bit" "Not masked,Masked" bitfld.long 0x04 5. " RIL ,RIL Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 4. " RFC ,RFC Mask Bit" "Not masked,Masked" bitfld.long 0x04 3. " RFS ,RFS Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 2. " TAB ,TAB Mask Bit" "Not masked,Masked" bitfld.long 0x04 1. " TFC ,TFC Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 0. " TFS ,TFS Mask Bit" "Not masked,Masked" rgroup asd:0x0088++0x03 line.long 0x00 "MIIR,MIR Interrupt Register" bitfld.long 0x00 6. " RFL ,RFL Masked Bit" "Low,High" bitfld.long 0x00 5. " RIL ,RIL Masked Bit" "Low,High" textline " " bitfld.long 0x00 4. " RFC ,RFC Masked Bit" "Low,High" bitfld.long 0x00 3. " RFS ,RFS Masked Bit" "Low,High" textline " " bitfld.long 0x00 2. " TAB ,TAB Masked Bit" "Low,High" bitfld.long 0x00 1. " TFC ,TFC Masked Bit" "Low,High" textline " " bitfld.long 0x00 0. " TFS ,TFS Masked Bit" "Low,High" group asd:0x0180++7 line.long 0x00 "FISR,FIR Status Register" bitfld.long 0x00 6. " RFL ,Receive Frame Lost" "Not lost,Lost" bitfld.long 0x00 5. " RIL ,Receive Information Buffer Lost" "Not lost,Lost" textline " " bitfld.long 0x00 4. " RFC ,Receive Frame Complete" "Not completed,Completed" bitfld.long 0x00 3. " RFS ,Reveive Buffer Service Request" "Not requested,Requested" textline " " bitfld.long 0x00 2. " TAB ,Transmit Frame Aborted" "Not aborted,Aborted" bitfld.long 0x00 1. " TFC ,Transmit Frame Complete" "Not completed,Completed" textline " " bitfld.long 0x00 0. " TFS ,Transmit Buffer Service Request" "Not requested,Requested" line.long 0x04 "FIMR,FIR Interrupt Mask Register" bitfld.long 0x04 6. " RFL ,RFL Mask Bit" "Not masked,Masked" bitfld.long 0x04 5. " RIL ,RIL Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 4. " RFC ,RFC Mask Bit" "Not masked,Masked" bitfld.long 0x04 3. " RFS ,RFS Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 2. " TAB ,TAB Mask Bit" "Not masked,Masked" bitfld.long 0x04 1. " TFC ,TFC Mask Bit" "Not masked,Masked" textline " " bitfld.long 0x04 0. " TFS ,TFS Mask Bit" "Not masked,Masked" rgroup asd:0x0188++3 line.long 0x00 "FIIR,FIR Interrupt Register" bitfld.long 0x00 6. " RFL ,RFL Masked Bit" "Low,High" bitfld.long 0x00 5. " RIL ,RIL Masked Bit" "Low,High" textline " " bitfld.long 0x00 4. " RFC ,RFC Masked Bit" "Low,High" bitfld.long 0x00 3. " RFS ,RFS Masked Bit" "Low,High" textline " " bitfld.long 0x00 2. " TAB ,TAB Masked Bit" "Low,High" bitfld.long 0x00 1. " TFC ,TFC Masked Bit" "Low,High" textline " " bitfld.long 0x00 0. " TFS ,TFS Masked Bit" "Low,High" ;end include file ep9312/irda.ph tree.end tree "Timers" base asd:0x80810000 ;begin include file ep9312/timer.ph ;parameters: tree "Timer 1" group asd:0x0000++3 line.long 0x00 "Timer1Load,Timer 1 Load Register" hexmask.long.word 0x00 0.--15. 1. " Load ,Load Value" rgroup asd:0x0004++3 line.long 0x00 "Timer1Value,Timer 1 Value Register" hexmask.long.word 0x00 0.--15. 1. " Value ,Current Timer Value" group asd:0x0008++3 line.long 0x00 "Timer1Control,Timer 1 Control Register" bitfld.long 0x00 7. " ENABLE ,Timer Enable Bit" "Disabled,Enabled" bitfld.long 0x00 6. " MODE ,Operation Mode" "Free running,Periodic" bitfld.long 0x00 3. " CLKSEL ,Clock Select" "2kHz,508Hz" wgroup asd:0x000C++3 line.long 0x00 "Timer1Clear,Timer 1 Clear Register" tree.end tree "Timer 2" group asd:0x0020++3 line.long 0x00 "Timer2Load,Timer 2 Load Register" hexmask.long.word 0x00 0.--15. 1. " Load ,Load Value" rgroup asd:0x0024++3 line.long 0x00 "Timer2Value,Timer 2 Value Register" hexmask.long.word 0x00 0.--15. 1. " Value ,Current Timer Value" group asd:0x0028++3 line.long 0x00 "Timer2Control,Timer 2 Control Register" bitfld.long 0x00 7. " ENABLE ,Timer Enable Bit" "Disabled,Enabled" bitfld.long 0x00 6. " MODE ,Operation Mode" "Free running,Periodic" bitfld.long 0x00 3. " CLKSEL ,Clock Select" "2kHz,508Hz" wgroup asd:0x002C++3 line.long 0x00 "Timer2Clear,Timer 2 Clear Register" tree.end tree "Timer 3" group asd:0x0080++3 line.long 0x00 "Timer3Load,Timer 3 Load Register" hexmask.long 0x00 0.--31. 1. " Load ,Load Value" rgroup asd:0x0084++3 line.long 0x00 "Timer3Value,Timer 3 Value Register" hexmask.long 0x00 0.--31. 1. " Value ,Current Timer Value" group asd:0x0088++3 line.long 0x00 "Timer3Control,Timer 3 Control Register" bitfld.long 0x00 7. " ENABLE ,Timer Enable Bit" "Disabled,Enabled" bitfld.long 0x00 6. " MODE ,Operation Mode" "Free running,Periodic" bitfld.long 0x00 3. " CLKSEL ,Clock Select" "2kHz,508Hz" wgroup asd:0x008C++3 line.long 0x00 "Timer3Clear,Timer 3 Clear Register" tree.end tree "Timer 4" rgroup asd:0x0060++3 line.long 0x00 "Timer4ValueLow,Timer 4 Value Low Register" hexmask.long 0x00 0.--31. 1. " Value ,Timer 4 Low Value" group asd:0x0064++3 line.long 0x00 "Timer4Enable,Timer 4 Enable/Value High Register" bitfld.long 0x00 8. " Enable ,Timer 4 Enable" "Disabled,Enabled" hexmask.long.byte 0x00 0.--7. 1. " Value ,TImer 4 High Value" tree.end ;end include file ep9312/timer.ph tree.end tree "Watchdog Timer" base asd:0x80940000 ;begin include file ep9312/watchdog.ph ;parameters: rgroup asd:0x0000++3 line.long 0x00 "Watchdog,Watchdog Control Register (Read only)" bitfld.long 0x00 6. " PLSDSN ,Pulse Disable Not" "Disabled,Enabled" bitfld.long 0x00 5. " VRID ,Software Override of Hardware Watchdog Disable" "Not overrided,Overrided" bitfld.long 0x00 4. " SWDIS ,Software Wachdog Disable" "Enabled,Disabled" textline " " bitfld.long 0x00 3. " HWDIS ,Hardware Watchdog Disable" "Enabled,Disabled" bitfld.long 0x00 2. " URST ,User Reset Status Flip Flop" "No reset,User reset" bitfld.long 0x00 1. " 3LRST ,Three Key Reset Status Flip Flop" "No reset,Three-key reset" textline " " bitfld.long 0x00 0. " WD ,Watchdog Reset Status Flip Flop" "No reset,Reset" wgroup asd:0x0000++3 line.long 0x00 "Watchdog,Watchdog Control Register (Write only)" hexmask.long 0x00 0.--15. 1. " CTL ,Watchdog Control Bits" group asd:0x0004++3 line.long 0x00 "WDSTatus,Watchdog Storage Register" hexmask.long.byte 0x00 0.--6. 1. " STAT ,Watchdog Status Bits" ;end include file ep9312/watchdog.ph tree.end tree "Real Time Clock with Software Trim" base asd:0x80920000 ;begin include file ep9312/rtc.ph ;parameters: rgroup asd:0x0000++3 line.long 0x00 "RTCData,RTC Data Register" hexfld.long 0x00 " RTCDR ,Counter Value" group asd:0x0004++3 line.long 0x00 "RTCMatch,RTC Match Register" hexfld.long 0x00 " RTCMR ,Match Value" group asd:0x0008++3 line.long 0x00 "RTCSts,RTC Status/EOI Register" bitfld.long 0x00 0. " INTR ,Interrupt Status" "No Interrupt,Interrupt" group asd:0x000C++3 line.long 0x00 "RTCLoad,RTC Load Register" hexfld.long 0x00 " RTCLR ,Load Value" group asd:0x0010++3 line.long 0x00 "RTCCtrl,RTC Control Register" bitfld.long 0x00 0. " MIE ,Match Interrupt Enable" "Disabled,Enabled" group asd:0x0108++3 line.long 0x00 "RTCSWComp,RTC Software Compensation" hexmask.long.byte 0x00 16.--20. 1. " DEL ,Number of Clocks to Delete" hexmask.long.word 0x00 0.--15. 1. " INT ,Counter Pre-Load Integer Value" ;end include file ep9312/rtc.ph tree.end tree "I2S Controller" base asd:0x80820000 ;begin include file ep9312/i2s.ph ;parameters: tree "I2S TX Registers" group asd:0x0010++7 line.long 0x00 "I2STX0Lft,Left Transmit Data Register for Channel 0" hexfld.long 0x00 " I2s_tx0_left ,Transmit Left Data Word for Channel 0" line.long 0x04 "I2SRX0Rt,Right Transmit Data Register for Channel 0" hexfld.long 0x04 " I2s_tx0_right ,Transmit Right Data Word for Channel 0" group asd:0x0018++7 line.long 0x00 "I2STX1Lft,Left Transmit Data Register for Channel 1" hexfld.long 0x00 " I2s_tx1_left ,Transmit Left Data Word for Channel 1" line.long 0x04 "I2SRX1Rt,Right Transmit Data Register for Channel 1" hexfld.long 0x04 " I2s_tx1_right ,Transmit Right Data Word for Channel 1" group asd:0x0020++7 line.long 0x00 "I2STX2Lft,Left Transmit Data Register for Channel 2" hexfld.long 0x00 " I2s_tx2_left ,Transmit Left Data Word for Channel 2" line.long 0x04 "I2SRX2Rt,Right Transmit Data Register for Channel 2" hexfld.long 0x04 " I2s_tx2_right ,Transmit Right Data Word for Channel 2" group asd:0x0028++7 line.long 0x00 "I2STXLinCtrlData,Line Control Data Register" bitfld.long 0x00 2. " Left_Right_Justify ,Data Justify" "Left,Right" textline " " bitfld.long 0x00 1. " TXUF_REPEAT_SAMPLE ,Data Trasmit After TX Underflow" "Repeat sample,Transmit ones" textline " " bitfld.long 0x00 0. " TXDIR ,Transmit Data Shift Direction" "MSB first,LSB First" line.long 0x04 "I2STXCtrl,Control Register" bitfld.long 0x04 1. " TXUFIE ,Transmit Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " TXEMPTY_int_level ,Transmit Empty Interrupt Level Select" "When half empty,When empty" group asd:0x0030++3 line.long 0x00 "I2STXWrdLen,Word Length Register" bitfld.long 0x00 0.--1. " WL ,Word Length" "16-bit,24-bit,32-bit," group asd:0x0034++0x0B line.long 0x00 "I2STX0En,TX0 Channel Enable Register" bitfld.long 0x00 0. " I2s_tx0_EN ,TX0 Channel Enable" "Disabled,Enabled" line.long 0x04 "I2STX1En,TX1 Channel Enable Register" bitfld.long 0x04 0. " I2s_tx1_EN ,TX1 Channel Enable" "Disabled,Enabled" line.long 0x08 "I2STX2En,TX2 Channel Enable Register" bitfld.long 0x08 0. " I2s_tx2_EN ,TX2 Channel Enable" "Disabled,Enabled" tree.end tree "I2S RX Registers" rgroup asd:0x0040++7 line.long 0x00 "I2SRX0Lft,Left Receive Data Register for Channel 0" hexfld.long 0x00 " I2s_rx0_left ,Receive Left Data Word for Channel 0" line.long 0x04 "I2SRX0Rt,Right Receive Data Register for Channel 0" hexfld.long 0x04 " I2s_rx0_right ,Receive Right Data Word for Channel 0" rgroup asd:0x0048++7 line.long 0x00 "I2SRX1Lft,Left Receive Data Register for Channel 1" hexfld.long 0x00 " I2s_rx1_left ,Receive Left Data Word for Channel 1" line.long 0x04 "I2SRX1Rt,Right Receive Data Register for Channel 1" hexfld.long 0x04 " I2s_rx1_right ,Receive Right Data Word for Channel 1" rgroup asd:0x0050++7 line.long 0x00 "I2SRX2Lft,Left Receive Data Register for Channel 2" hexfld.long 0x00 " I2s_rx2_left ,Receive Left Data Word for Channel 2" line.long 0x04 "I2SRX2Rt,Right Receive Data Register for Channel 2" hexfld.long 0x04 " I2s_rx2_right ,Receive Right Data Word for Channel 2" group asd:0x0058++0x0B line.long 0x00 "I2SRXLinCtrlData,Line Control Data Register" bitfld.long 0x00 2. " Left_Right_Justify ,Data Justify" "Left,Right" textline " " bitfld.long 0x00 0. " RXDIR ,Receive Data Shift Direction" "MSB first,LSB First" line.long 0x04 "I2SRXCtrl,Control Register" bitfld.long 0x04 1. " ROUFIE ,Receive Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " RXFull_int_level ,Receive Full Interrupt Level Select" "When half full,When full" line.long 0x08 "I2SRXWrdLen,Word Length Register" bitfld.long 0x08 0.--1. " WL ,Word Length" "16-bit,24-bit,32-bit," group asd:0x0064++0x0B line.long 0x00 "I2SRX0En,RX0 Channel Enable Register" bitfld.long 0x00 0. " I2s_rx0_EN ,RX0 Channel Enable" "Disabled,Enabled" line.long 0x04 "I2SRX1En,RX1 Channel Enable Register" bitfld.long 0x04 0. " I2s_rx1_EN ,RX1 Channel Enable" "Disabled,Enabled" line.long 0x08 "I2SRX2En,RX2 Channel Enable Register" bitfld.long 0x08 0. " I2s_rx2_EN ,RX2 Channel Enable" "Disabled,Enabled" tree.end tree "I2S Configuration and Status Registers" if ((data.long(asd:0x0000)&0x00000060)==0x00000000) group asd:0x0000++3 line.long 0x00 "I2STXClkCfg,Transmitter Clock Configuration Register" bitfld.long 0x00 5.--6. " I2s_tx_bcr ,TX Bit Clock Rate" "I2STXClkCfg[4],Fixed at 32x,Fixed at 64x,Fixed at 128x" bitfld.long 0x00 4. " I2s_fx_nbcg ,TX Not Bit Clock Gating Mode" "Low,High" textline " " bitfld.long 0x00 3. " I2s_mstr ,TX Audio Clock Master/Slave" "Slave,Master" bitfld.long 0x00 2. " I2s_trel ,Timing of Irckt Respect to Sdix Data Outputs" "Together,One cycle before" textline " " bitfld.long 0x00 1. " I2s_tckp ,TX Bitclk Polarity" "Negative,Positive" bitfld.long 0x00 0. " I2s_tlrs ,Irckt Polarity" "Low->left/High->right,Low->high/High->left" else group asd:0x0000++3 line.long 0x00 "I2STXClkCfg,Transmitter Clock Configuration Register" bitfld.long 0x00 5.--6. " I2s_tx_bcr ,TX Bit Clock Rate" "I2STXClkCfg[4],Fixed at 32x,Fixed at 64x,Fixed at 128x" textline " " bitfld.long 0x00 3. " I2s_mstr ,TX Audio Clock Master/Slave" "Slave,Master" bitfld.long 0x00 2. " I2s_trel ,Timing of Irckt Respect to Sdix Data Outputs" "Together,One cycle before" textline " " bitfld.long 0x00 1. " I2s_tckp ,TX Bitclk Polarity" "Negative,Positive" bitfld.long 0x00 0. " I2s_tlrs ,Irckt Polarity" "Low->left/High->right,Low->high/High->left" endif if ((data.long(asd:0x0004)&0x00000060)==0x00000000) group asd:0x0004++3 line.long 0x00 "I2SRXClkCfg,Receiver Clock Configuration Register" bitfld.long 0x00 5.--6. " I2s_rx_bcr ,RX Bit Clock Rate" "I2STXClkCfg[4],Fixed at 32x,Fixed at 64x,Fixed at 128x" bitfld.long 0x00 4. " I2s_fx_nbcg ,RX Not Bit Clock Gating Mode" "Low,High" textline " " bitfld.long 0x00 3. " I2s_mstr ,RX Audio Clock Master/Slave" "Slave,Master" bitfld.long 0x00 2. " I2s_trel ,Timing of Irckr Respect to Sdix Data Outputs" "Together,One cycle before" textline " " bitfld.long 0x00 1. " I2s_tckp ,RX Bitclk Polarity" "Negative,Positive" bitfld.long 0x00 0. " I2s_tlrs ,Irckr Polarity" "Low->left/High->right,Low->high/High->left" else group asd:0x0004++3 line.long 0x00 "I2SRXClkCfg,Receiver Clock Configuration Register" bitfld.long 0x00 5.--6. " I2s_rx_bcr ,RX Bit Clock Rate" "I2STXClkCfg[4],Fixed at 32x,Fixed at 64x,Fixed at 128x" textline " " bitfld.long 0x00 3. " I2s_mstr ,RX Audio Clock Master/Slave" "Slave,Master" bitfld.long 0x00 2. " I2s_trel ,Timing of Irckr Respect to Sdix Data Outputs" "Together,One cycle before" textline " " bitfld.long 0x00 1. " I2s_tckp ,RX Bitclk Polarity" "Negative,Positive" bitfld.long 0x00 0. " I2s_tlrs ,Irckr Polarity" "Low->left/High->right,Low->high/High->left" endif group asd:0x0008++3 line.long 0x00 "I2SGISts,I2S Global Status Register" bitfld.long 0x00 29. " rx2_fifo_half_full ,RX2 FIFO Half Full" "Not half full,Half full" bitfld.long 0x00 28. " rx2_fifo_empty ,RX2 FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 27. " rx2_fifo_full ,RX2 FIFO Full" "Not full,Full" bitfld.long 0x00 26. " tx2_fifo_half_full ,TX2 FIFO Half Full" "Not half full,Half full" textline " " bitfld.long 0x00 25. " tx2_fifo_empty ,TX2 FIFO Empty" "Not empty,Empty" bitfld.long 0x00 24. " tx2_fifo_full ,TX2 FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 23. " rx1_fifo_half_full ,RX1 FIFO Half Full" "Not half full,Half full" bitfld.long 0x00 22. " rx1_fifo_empty ,RX1 FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 21. " rx1_fifo_full ,RX1 FIFO Full" "Not full,Full" bitfld.long 0x00 20. " tx1_fifo_half_full ,TX1 FIFO Half Full" "Not half full,Half full" textline " " bitfld.long 0x00 19. " tx1_fifo_empty ,TX1 FIFO Empty" "Not empty,Empty" bitfld.long 0x00 18. " tx1_fifo_full ,TX1 FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 17. " rx0_fifo_half_full ,RX0 FIFO Half Full" "Not half full,Half full" bitfld.long 0x00 16. " rx0_fifo_empty ,RX0 FIFO Empty" "Not empty,Empty" textline " " bitfld.long 0x00 15. " rx0_fifo_full ,RX0 FIFO Full" "Not full,Full" bitfld.long 0x00 14. " tx0_fifo_half_full ,TX0 FIFO Half Full" "Not half full,Half full" textline " " bitfld.long 0x00 13. " tx0_fifo_empty ,TX0 FIFO Empty" "Not empty,Empty" bitfld.long 0x00 12. " tx0_fifo_full ,TX0 FIFO Full" "Not full,Full" textline " " bitfld.long 0x00 11. " rx2_underflow ,RX2 Underflow" "Not underflowed,Underflowed" bitfld.long 0x00 10. " rx1_underflow ,RX1 Underflow" "Not underflowed,Underflowed" textline " " bitfld.long 0x00 9. " rx0_underflow ,RX0 Underflow" "Not underflowed,Underflowed" bitfld.long 0x00 8. " tx2_overflow ,TX2 Overflow" "Not overflowed,Overflowed" textline " " bitfld.long 0x00 7. " tx1_overflow ,TX1 Overflow" "Not overflowed,Overflowed" bitfld.long 0x00 6. " tx0_overflow ,TX0 Overflow" "Not overflowed,Overflowed" textline " " bitfld.long 0x00 5. " rx2_overflow ,RX2 Overflow" "Not overflowed,Overflowed" bitfld.long 0x00 4. " rx1_overflow ,RX1 Overflow" "Not overflowed,Overflowed" textline " " bitfld.long 0x00 3. " rx0_overflow ,RX0 Overflow" "Not overflowed,Overflowed" bitfld.long 0x00 2. " tx2_underflow ,TX2 Underflow" "Not underflowed,Underflowed" textline " " bitfld.long 0x00 1. " tx1_underflow ,TX1 Underflow" "Not underflowed,Underflowed" bitfld.long 0x00 0. " tx0_underflow ,TX0 Underflow" "Not underflowed,Underflowed" group asd:0x000C++3 line.long 0x00 "I2SGICtrl,I2S Global Control Register" bitfld.long 0x00 1. " I2s_loopback ,Loopback Operation" "No loopback mode,Loopback mode" bitfld.long 0x00 0. " I2s_ife ,PCLK Enable" "Off,On" tree.end ;end include file ep9312/i2s.ph tree.end tree "AC'97 Controller" base asd:0x80880000 ;begin include file ep9312/ac97.ph ;parameters: tree "Channel 1" base asd:0x80880000 ;begin include file ep9312/ac97/acxrx.ph ;parameters: 0x80880004 1 group asd:0x0000++3 line.long 0x00 "AC97DR1,Data Read/Write from/to FIFO1" hexfld.long 0x00 " DATA ,Data Receive/Transmit" group asd:0x0004++7 line.long 0x00 "AC97RXCR1,Receive Control Register" hexmask.long.word 0x00 17.--28. 1. " TOC ,Time-Out Count Value" bitfld.long 0x00 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x00 15. " CM ,Compact Mode Enable" "Jutified,Compact" textline " " bitfld.long 0x00 13.--14. " RSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" bitfld.long 0x00 12. " RX12 ,FIFO Stores SLOT12 Data" "Not stored,Stored" bitfld.long 0x00 11. " RX11 ,FIFO Stores SLOT11 Data" "Not stored,Stored" textline " " bitfld.long 0x00 10. " RX10 ,FIFO Stores SLOT10 Data" "Not stored,Stored" bitfld.long 0x00 9. " RX9 ,FIFO Stores SLOT9 Data" "Not stored,Stored" bitfld.long 0x00 8. " RX8 ,FIFO Stores SLOT8 Data" "Not stored,Stored" textline " " bitfld.long 0x00 7. " RX7 ,FIFO Stores SLOT7 Data" "Not stored,Stored" bitfld.long 0x00 6. " RX6 ,FIFO Stores SLOT6 Data" "Not stored,Stored" bitfld.long 0x00 5. " RX5 ,FIFO Stores SLOT5 Data" "Not stored,Stored" textline " " bitfld.long 0x00 4. " RX4 ,FIFO Stores SLOT4 Data" "Not stored,Stored" bitfld.long 0x00 3. " RX3 ,FIFO Stores SLOT3 Data" "Not stored,Stored" bitfld.long 0x00 2. " RX2 ,FIFO Stores SLOT2 Data" "Not stored,Stored" textline " " bitfld.long 0x00 1. " RX1 ,FIFO Stores SLOT1 Data" "Not stored,Stored" bitfld.long 0x00 0. " REN ,PCLK and Receive Enable for Channel 1" "Disabled,Enabled" line.long 0x04 "AC97TXCR1,Transmit Control Register" bitfld.long 0x04 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x04 15. " CM ,Compact Mode Enable" "Jutified,Compact" bitfld.long 0x04 13.--14. " TSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" textline " " bitfld.long 0x04 12. " TX12 ,FIFO Stores SLOT12 Data" "Not Stored,Stored" bitfld.long 0x04 11. " TX11 ,FIFO Stores SLOT11 Data" "Not Stored,Stored" bitfld.long 0x04 10. " TX10 ,FIFO Stores SLOT10 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 9. " TX9 ,FIFO Stores SLOT9 Data" "Not Stored,Stored" bitfld.long 0x04 8. " TX8 ,FIFO Stores SLOT8 Data" "Not Stored,Stored" bitfld.long 0x04 7. " TX7 ,FIFO Stores SLOT7 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 6. " TX6 ,FIFO Stores SLOT6 Data" "Not Stored,Stored" bitfld.long 0x04 5. " TX5 ,FIFO Stores SLOT5 Data" "Not Stored,Stored" bitfld.long 0x04 4. " TX4 ,FIFO Stores SLOT4 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 3. " TX3 ,FIFO Stores SLOT3 Data" "Not Stored,Stored" bitfld.long 0x04 2. " TX2 ,FIFO Contains SLOT2 Data" "Not contains,Contains" bitfld.long 0x04 1. " TX1 ,FIFO Contains SLOT1 Data" "Not contains,Contains" textline " " bitfld.long 0x04 0. " TEN ,PCLK and Transmit Enable for Channel 1" "Disabled,Enabled" rgroup asd:0x000C++0x0B line.long 0x00 "AC97SR1,Status Register" bitfld.long 0x00 6. " TXUE ,TX Underrun Error" "No error,Error" bitfld.long 0x00 5. " RXOE ,RX Overrun Error" "No error,Error" bitfld.long 0x00 4. " TXBUSY ,TX Busy" "Not busy,Busy" textline " " bitfld.long 0x00 3. " TXFF ,Transmit FIFO Full Flag" "Not full,Full" bitfld.long 0x00 2. " RXFF ,Receive FIFO Full Flag" "Not full,Full" bitfld.long 0x00 1. " TXFE ,Transmit FIFO Empty Flag" "Not empty,Empty" textline " " bitfld.long 0x00 0. " RXFE ,Receive FIFO Empty Flag" "Not empty,Empty" line.long 0x04 "AC97RISR1,Raw Interrupt Status Register" bitfld.long 0x04 3. " RIS ,RX Half Full Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 2. " TIS ,TX Half Empty Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 1. " RTIS ,RX Timeout Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " TCIS ,TX Complete Interrupt Status" "No interrupt,Interrupt" line.long 0x08 "AC97ISR1,Interrupt Status Register" bitfld.long 0x08 3. " RIS ,RX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 2. " TIS ,TX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 1. " RTIS ,RX Timeout Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x08 0. " TCIS ,TX Complete Interrupt Assertion" "Not asserted,Asserted" group asd:0x0018++3 line.long 0x00 "AC97IE1,Interrupt Enable Register" bitfld.long 0x00 3. " RIE ,RX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TIE ,TX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " RTIE ,RX Timeout Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " TCIE ,TX Complete Interrupt Enable" "Disabled,Enabled" ;end include file ep9312/ac97/acxrx.ph tree.end tree "Channel 2" base asd:0x80880020 ;begin include file ep9312/ac97/acxrx.ph ;parameters: 0x80880024 2 group asd:0x0000++3 line.long 0x00 "AC97DR2,Data Read/Write from/to FIFO2" hexfld.long 0x00 " DATA ,Data Receive/Transmit" group asd:0x0004++7 line.long 0x00 "AC97RXCR2,Receive Control Register" hexmask.long.word 0x00 17.--28. 1. " TOC ,Time-Out Count Value" bitfld.long 0x00 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x00 15. " CM ,Compact Mode Enable" "Jutified,Compact" textline " " bitfld.long 0x00 13.--14. " RSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" bitfld.long 0x00 12. " RX12 ,FIFO Stores SLOT12 Data" "Not stored,Stored" bitfld.long 0x00 11. " RX11 ,FIFO Stores SLOT11 Data" "Not stored,Stored" textline " " bitfld.long 0x00 10. " RX10 ,FIFO Stores SLOT10 Data" "Not stored,Stored" bitfld.long 0x00 9. " RX9 ,FIFO Stores SLOT9 Data" "Not stored,Stored" bitfld.long 0x00 8. " RX8 ,FIFO Stores SLOT8 Data" "Not stored,Stored" textline " " bitfld.long 0x00 7. " RX7 ,FIFO Stores SLOT7 Data" "Not stored,Stored" bitfld.long 0x00 6. " RX6 ,FIFO Stores SLOT6 Data" "Not stored,Stored" bitfld.long 0x00 5. " RX5 ,FIFO Stores SLOT5 Data" "Not stored,Stored" textline " " bitfld.long 0x00 4. " RX4 ,FIFO Stores SLOT4 Data" "Not stored,Stored" bitfld.long 0x00 3. " RX3 ,FIFO Stores SLOT3 Data" "Not stored,Stored" bitfld.long 0x00 2. " RX2 ,FIFO Stores SLOT2 Data" "Not stored,Stored" textline " " bitfld.long 0x00 1. " RX1 ,FIFO Stores SLOT1 Data" "Not stored,Stored" bitfld.long 0x00 0. " REN ,PCLK and Receive Enable for Channel 2" "Disabled,Enabled" line.long 0x04 "AC97TXCR2,Transmit Control Register" bitfld.long 0x04 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x04 15. " CM ,Compact Mode Enable" "Jutified,Compact" bitfld.long 0x04 13.--14. " TSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" textline " " bitfld.long 0x04 12. " TX12 ,FIFO Stores SLOT12 Data" "Not Stored,Stored" bitfld.long 0x04 11. " TX11 ,FIFO Stores SLOT11 Data" "Not Stored,Stored" bitfld.long 0x04 10. " TX10 ,FIFO Stores SLOT10 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 9. " TX9 ,FIFO Stores SLOT9 Data" "Not Stored,Stored" bitfld.long 0x04 8. " TX8 ,FIFO Stores SLOT8 Data" "Not Stored,Stored" bitfld.long 0x04 7. " TX7 ,FIFO Stores SLOT7 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 6. " TX6 ,FIFO Stores SLOT6 Data" "Not Stored,Stored" bitfld.long 0x04 5. " TX5 ,FIFO Stores SLOT5 Data" "Not Stored,Stored" bitfld.long 0x04 4. " TX4 ,FIFO Stores SLOT4 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 3. " TX3 ,FIFO Stores SLOT3 Data" "Not Stored,Stored" bitfld.long 0x04 2. " TX2 ,FIFO Contains SLOT2 Data" "Not contains,Contains" bitfld.long 0x04 1. " TX1 ,FIFO Contains SLOT1 Data" "Not contains,Contains" textline " " bitfld.long 0x04 0. " TEN ,PCLK and Transmit Enable for Channel 2" "Disabled,Enabled" rgroup asd:0x000C++0x0B line.long 0x00 "AC97SR2,Status Register" bitfld.long 0x00 6. " TXUE ,TX Underrun Error" "No error,Error" bitfld.long 0x00 5. " RXOE ,RX Overrun Error" "No error,Error" bitfld.long 0x00 4. " TXBUSY ,TX Busy" "Not busy,Busy" textline " " bitfld.long 0x00 3. " TXFF ,Transmit FIFO Full Flag" "Not full,Full" bitfld.long 0x00 2. " RXFF ,Receive FIFO Full Flag" "Not full,Full" bitfld.long 0x00 1. " TXFE ,Transmit FIFO Empty Flag" "Not empty,Empty" textline " " bitfld.long 0x00 0. " RXFE ,Receive FIFO Empty Flag" "Not empty,Empty" line.long 0x04 "AC97RISR2,Raw Interrupt Status Register" bitfld.long 0x04 3. " RIS ,RX Half Full Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 2. " TIS ,TX Half Empty Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 1. " RTIS ,RX Timeout Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " TCIS ,TX Complete Interrupt Status" "No interrupt,Interrupt" line.long 0x08 "AC97ISR2,Interrupt Status Register" bitfld.long 0x08 3. " RIS ,RX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 2. " TIS ,TX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 1. " RTIS ,RX Timeout Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x08 0. " TCIS ,TX Complete Interrupt Assertion" "Not asserted,Asserted" group asd:0x0018++3 line.long 0x00 "AC97IE2,Interrupt Enable Register" bitfld.long 0x00 3. " RIE ,RX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TIE ,TX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " RTIE ,RX Timeout Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " TCIE ,TX Complete Interrupt Enable" "Disabled,Enabled" ;end include file ep9312/ac97/acxrx.ph tree.end tree "Channel 3" base asd:0x80880040 ;begin include file ep9312/ac97/acxrx.ph ;parameters: 0x80880044 3 group asd:0x0000++3 line.long 0x00 "AC97DR3,Data Read/Write from/to FIFO3" hexfld.long 0x00 " DATA ,Data Receive/Transmit" group asd:0x0004++7 line.long 0x00 "AC97RXCR3,Receive Control Register" hexmask.long.word 0x00 17.--28. 1. " TOC ,Time-Out Count Value" bitfld.long 0x00 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x00 15. " CM ,Compact Mode Enable" "Jutified,Compact" textline " " bitfld.long 0x00 13.--14. " RSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" bitfld.long 0x00 12. " RX12 ,FIFO Stores SLOT12 Data" "Not stored,Stored" bitfld.long 0x00 11. " RX11 ,FIFO Stores SLOT11 Data" "Not stored,Stored" textline " " bitfld.long 0x00 10. " RX10 ,FIFO Stores SLOT10 Data" "Not stored,Stored" bitfld.long 0x00 9. " RX9 ,FIFO Stores SLOT9 Data" "Not stored,Stored" bitfld.long 0x00 8. " RX8 ,FIFO Stores SLOT8 Data" "Not stored,Stored" textline " " bitfld.long 0x00 7. " RX7 ,FIFO Stores SLOT7 Data" "Not stored,Stored" bitfld.long 0x00 6. " RX6 ,FIFO Stores SLOT6 Data" "Not stored,Stored" bitfld.long 0x00 5. " RX5 ,FIFO Stores SLOT5 Data" "Not stored,Stored" textline " " bitfld.long 0x00 4. " RX4 ,FIFO Stores SLOT4 Data" "Not stored,Stored" bitfld.long 0x00 3. " RX3 ,FIFO Stores SLOT3 Data" "Not stored,Stored" bitfld.long 0x00 2. " RX2 ,FIFO Stores SLOT2 Data" "Not stored,Stored" textline " " bitfld.long 0x00 1. " RX1 ,FIFO Stores SLOT1 Data" "Not stored,Stored" bitfld.long 0x00 0. " REN ,PCLK and Receive Enable for Channel 3" "Disabled,Enabled" line.long 0x04 "AC97TXCR3,Transmit Control Register" bitfld.long 0x04 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x04 15. " CM ,Compact Mode Enable" "Jutified,Compact" bitfld.long 0x04 13.--14. " TSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" textline " " bitfld.long 0x04 12. " TX12 ,FIFO Stores SLOT12 Data" "Not Stored,Stored" bitfld.long 0x04 11. " TX11 ,FIFO Stores SLOT11 Data" "Not Stored,Stored" bitfld.long 0x04 10. " TX10 ,FIFO Stores SLOT10 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 9. " TX9 ,FIFO Stores SLOT9 Data" "Not Stored,Stored" bitfld.long 0x04 8. " TX8 ,FIFO Stores SLOT8 Data" "Not Stored,Stored" bitfld.long 0x04 7. " TX7 ,FIFO Stores SLOT7 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 6. " TX6 ,FIFO Stores SLOT6 Data" "Not Stored,Stored" bitfld.long 0x04 5. " TX5 ,FIFO Stores SLOT5 Data" "Not Stored,Stored" bitfld.long 0x04 4. " TX4 ,FIFO Stores SLOT4 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 3. " TX3 ,FIFO Stores SLOT3 Data" "Not Stored,Stored" bitfld.long 0x04 2. " TX2 ,FIFO Contains SLOT2 Data" "Not contains,Contains" bitfld.long 0x04 1. " TX1 ,FIFO Contains SLOT1 Data" "Not contains,Contains" textline " " bitfld.long 0x04 0. " TEN ,PCLK and Transmit Enable for Channel 3" "Disabled,Enabled" rgroup asd:0x000C++0x0B line.long 0x00 "AC97SR3,Status Register" bitfld.long 0x00 6. " TXUE ,TX Underrun Error" "No error,Error" bitfld.long 0x00 5. " RXOE ,RX Overrun Error" "No error,Error" bitfld.long 0x00 4. " TXBUSY ,TX Busy" "Not busy,Busy" textline " " bitfld.long 0x00 3. " TXFF ,Transmit FIFO Full Flag" "Not full,Full" bitfld.long 0x00 2. " RXFF ,Receive FIFO Full Flag" "Not full,Full" bitfld.long 0x00 1. " TXFE ,Transmit FIFO Empty Flag" "Not empty,Empty" textline " " bitfld.long 0x00 0. " RXFE ,Receive FIFO Empty Flag" "Not empty,Empty" line.long 0x04 "AC97RISR3,Raw Interrupt Status Register" bitfld.long 0x04 3. " RIS ,RX Half Full Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 2. " TIS ,TX Half Empty Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 1. " RTIS ,RX Timeout Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " TCIS ,TX Complete Interrupt Status" "No interrupt,Interrupt" line.long 0x08 "AC97ISR3,Interrupt Status Register" bitfld.long 0x08 3. " RIS ,RX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 2. " TIS ,TX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 1. " RTIS ,RX Timeout Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x08 0. " TCIS ,TX Complete Interrupt Assertion" "Not asserted,Asserted" group asd:0x0018++3 line.long 0x00 "AC97IE3,Interrupt Enable Register" bitfld.long 0x00 3. " RIE ,RX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TIE ,TX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " RTIE ,RX Timeout Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " TCIE ,TX Complete Interrupt Enable" "Disabled,Enabled" ;end include file ep9312/ac97/acxrx.ph tree.end tree "Channel 4" base asd:0x80880060 ;begin include file ep9312/ac97/acxrx.ph ;parameters: 0x80880064 4 group asd:0x0000++3 line.long 0x00 "AC97DR4,Data Read/Write from/to FIFO4" hexfld.long 0x00 " DATA ,Data Receive/Transmit" group asd:0x0004++7 line.long 0x00 "AC97RXCR4,Receive Control Register" hexmask.long.word 0x00 17.--28. 1. " TOC ,Time-Out Count Value" bitfld.long 0x00 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x00 15. " CM ,Compact Mode Enable" "Jutified,Compact" textline " " bitfld.long 0x00 13.--14. " RSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" bitfld.long 0x00 12. " RX12 ,FIFO Stores SLOT12 Data" "Not stored,Stored" bitfld.long 0x00 11. " RX11 ,FIFO Stores SLOT11 Data" "Not stored,Stored" textline " " bitfld.long 0x00 10. " RX10 ,FIFO Stores SLOT10 Data" "Not stored,Stored" bitfld.long 0x00 9. " RX9 ,FIFO Stores SLOT9 Data" "Not stored,Stored" bitfld.long 0x00 8. " RX8 ,FIFO Stores SLOT8 Data" "Not stored,Stored" textline " " bitfld.long 0x00 7. " RX7 ,FIFO Stores SLOT7 Data" "Not stored,Stored" bitfld.long 0x00 6. " RX6 ,FIFO Stores SLOT6 Data" "Not stored,Stored" bitfld.long 0x00 5. " RX5 ,FIFO Stores SLOT5 Data" "Not stored,Stored" textline " " bitfld.long 0x00 4. " RX4 ,FIFO Stores SLOT4 Data" "Not stored,Stored" bitfld.long 0x00 3. " RX3 ,FIFO Stores SLOT3 Data" "Not stored,Stored" bitfld.long 0x00 2. " RX2 ,FIFO Stores SLOT2 Data" "Not stored,Stored" textline " " bitfld.long 0x00 1. " RX1 ,FIFO Stores SLOT1 Data" "Not stored,Stored" bitfld.long 0x00 0. " REN ,PCLK and Receive Enable for Channel 4" "Disabled,Enabled" line.long 0x04 "AC97TXCR4,Transmit Control Register" bitfld.long 0x04 16. " FDIS ,FIFO Disable" "Enabled,Disabled" bitfld.long 0x04 15. " CM ,Compact Mode Enable" "Jutified,Compact" bitfld.long 0x04 13.--14. " TSIZE ,Size of Data Word" "16 bits,18 bits,20 bits,12 bits" textline " " bitfld.long 0x04 12. " TX12 ,FIFO Stores SLOT12 Data" "Not Stored,Stored" bitfld.long 0x04 11. " TX11 ,FIFO Stores SLOT11 Data" "Not Stored,Stored" bitfld.long 0x04 10. " TX10 ,FIFO Stores SLOT10 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 9. " TX9 ,FIFO Stores SLOT9 Data" "Not Stored,Stored" bitfld.long 0x04 8. " TX8 ,FIFO Stores SLOT8 Data" "Not Stored,Stored" bitfld.long 0x04 7. " TX7 ,FIFO Stores SLOT7 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 6. " TX6 ,FIFO Stores SLOT6 Data" "Not Stored,Stored" bitfld.long 0x04 5. " TX5 ,FIFO Stores SLOT5 Data" "Not Stored,Stored" bitfld.long 0x04 4. " TX4 ,FIFO Stores SLOT4 Data" "Not Stored,Stored" textline " " bitfld.long 0x04 3. " TX3 ,FIFO Stores SLOT3 Data" "Not Stored,Stored" bitfld.long 0x04 2. " TX2 ,FIFO Contains SLOT2 Data" "Not contains,Contains" bitfld.long 0x04 1. " TX1 ,FIFO Contains SLOT1 Data" "Not contains,Contains" textline " " bitfld.long 0x04 0. " TEN ,PCLK and Transmit Enable for Channel 4" "Disabled,Enabled" rgroup asd:0x000C++0x0B line.long 0x00 "AC97SR4,Status Register" bitfld.long 0x00 6. " TXUE ,TX Underrun Error" "No error,Error" bitfld.long 0x00 5. " RXOE ,RX Overrun Error" "No error,Error" bitfld.long 0x00 4. " TXBUSY ,TX Busy" "Not busy,Busy" textline " " bitfld.long 0x00 3. " TXFF ,Transmit FIFO Full Flag" "Not full,Full" bitfld.long 0x00 2. " RXFF ,Receive FIFO Full Flag" "Not full,Full" bitfld.long 0x00 1. " TXFE ,Transmit FIFO Empty Flag" "Not empty,Empty" textline " " bitfld.long 0x00 0. " RXFE ,Receive FIFO Empty Flag" "Not empty,Empty" line.long 0x04 "AC97RISR4,Raw Interrupt Status Register" bitfld.long 0x04 3. " RIS ,RX Half Full Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 2. " TIS ,TX Half Empty Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x04 1. " RTIS ,RX Timeout Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x04 0. " TCIS ,TX Complete Interrupt Status" "No interrupt,Interrupt" line.long 0x08 "AC97ISR4,Interrupt Status Register" bitfld.long 0x08 3. " RIS ,RX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 2. " TIS ,TX Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x08 1. " RTIS ,RX Timeout Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x08 0. " TCIS ,TX Complete Interrupt Assertion" "Not asserted,Asserted" group asd:0x0018++3 line.long 0x00 "AC97IE4,Interrupt Enable Register" bitfld.long 0x00 3. " RIE ,RX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 2. " TIE ,TX Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " RTIE ,RX Timeout Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " TCIE ,TX Complete Interrupt Enable" "Disabled,Enabled" ;end include file ep9312/ac97/acxrx.ph tree.end tree "Main Registers" base asd:0x80880000 ;begin include file ep9312/ac97/global.ph ;parameters: group asd:0x0080++0x0B line.long 0x00 "AC97S1Data,Slot 1 Data Register" hexmask.long.byte 0x00 0.--7. 1. " DATA ,Read/Write Data Value" line.long 0x04 "AC97S2Data,Slot 2 Data Register" hexmask.long.word 0x04 0.--15. 1. " DATA ,Read/Write Data Value" line.long 0x08 "AC97S12Data,Slot 12 Data Register" hexmask.long.tbyte 0x08 0.--19. 1. " DATA ,Read/Write Data Value" group asd:0x008C++3 line.long 0x00 "AC97RGIS,Raw Global Interrupt Status Register" bitfld.long 0x00 6. " SLOT2TXCOMPLETE ,AC97 Slot 2 Data Tramsmission Complete" "Not completed,Completed" bitfld.long 0x00 5. " CODECREADY ,Codec Ready" "Not ready,Ready" textline " " bitfld.long 0x00 4. " WINT ,RAW Wakeup Interrupt Status" "Not asserted,Asserted" bitfld.long 0x00 3. " GPIOINT ,GPIOINT Status Bit" "Low,High" textline " " bitfld.long 0x00 2. " GPIOTXCOMPLETE ,GPIO Transmission Complete" "Not completed,Completed" bitfld.long 0x00 1. " SLOT2RXVALID ,New Data in AC97S2Data Register" "No new data,New data" textline " " bitfld.long 0x00 0. " SLOT1TXCOMPLETE ,Transmission Complete" "Not completed,Completed" rgroup asd:0x0090++3 line.long 0x00 "AC97GIS,Global Interrupt Status Register" bitfld.long 0x00 6. " SLOT2TXCOMPLETE ,AC97 Slot 2 Data Tramsmission Complete Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x00 5. " CODECREADY ,Codec Ready Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x00 4. " WINT ,RAW Wakeup Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x00 3. " GPIOINT ,GPIOINT Bit Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x00 2. " GPIOTXCOMPLETE ,GPIO Transmission Complete Interrupt Assertion" "Not asserted,Asserted" bitfld.long 0x00 1. " SLOT2RXVALID ,New Data in AC97S2Data Register Interrupt Assertion" "Not asserted,Asserted" textline " " bitfld.long 0x00 0. " SLOT1TXCOMPLETE ,Transmission Complete Interrupt Assertion" "Not asserted,Asserted" group asd:0x0094++3 line.long 0x00 "AC97IM,Interrupt Enable Register" bitfld.long 0x00 6. " SLOT2TXCOMPLETE ,AC97 Slot 2 Data Tramsmission Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 5. " CODECREADY ,Codec Ready Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " WINT ,RAW Wakeup Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 3. " GPIOINT ,GPIOINT Bit Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 2. " GPIOTXCOMPLETE ,GPIO Transmission Complete Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 1. " SLOT2RXVALID ,New Data in AC97S2Data Register Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " SLOT1TXCOMPLETE ,Transmission Complete Interrupt Enable" "Disabled,Enabled" wgroup asd:0x0098++3 line.long 0x00 "AC97EOI,End of Interrupt Register" bitfld.long 0x00 1. " CODECREADY ,Codec Ready Interrupt Clear" "No effect,Clear" bitfld.long 0x00 0. " WINT ,Wakeup Interrupt Status Clear" "No effect,Clear" group asd:0x009C++0x0B line.long 0x00 "AC97GCR,Global Control Register" bitfld.long 0x00 2. " CODECReady ,CODEC Ready" "Not ready,Ready" bitfld.long 0x00 1. " LOOP ,Loopback Mode" "Disabled,Enabled" textline " " bitfld.long 0x00 0. " AC97IFE ,AC97IF Enable" "Disabled,Enabled" line.long 0x04 "AC97Reset,Controller Reset Register" bitfld.long 0x04 2. " EFORCER ,Forced RESET Enable" "Disabled,Enabled" bitfld.long 0x04 1. " FORCEDRESET ,Force Reset" "No reset,Reset" textline " " bitfld.long 0x04 0. " TIMEDRESET ,Timed Reset" "No reset,Reset" line.long 0x08 "AC97SYNC,SYNC Control Register" bitfld.long 0x08 2. " EFORCES ,Forced SYNC Enable" "Disabled,Enabled" bitfld.long 0x08 1. " FORCEDSYNC ,Forced SYNC" "Not forced,Forced" textline " " bitfld.long 0x08 0. " TIMEDSYNC ,Forced Timed SYNC" "Not forced,Forced" rgroup asd:0x00A8++3 line.long 0x00 "AC97GCIS,Global Channel FIFO Interrupt Status Register" hexmask.long.byte 0x00 16.--22. 1. " AC97GIS ,Copy of GIS Interrupt Register" hexmask.long.byte 0x00 12.--15. 1. " AC97ISR4 ,Copy of GISR4 Interrupt Register" textline " " hexmask.long.byte 0x00 8.--11. 1. " AC97ISR3 ,Copy of GISR3 Interrupt Register" hexmask.long.byte 0x00 4.--7. 1. " AC97ISR3 ,Copy of GISR2 Interrupt Register" textline " " hexmask.long.byte 0x00 0.--3. 1. " AC97ISR1 ,Copy of GISR1 Interrupt Register" ;end include file ep9312/ac97/global.ph tree.end ;end include file ep9312/ac97.ph tree.end tree "Synchronous Serial Port (SSP)" base asd:0x808A0000 ;begin include file ep9312/ssp.ph ;parameters: group asd:0x0000++7 line.long 0x00 "SSPCR0,Control Register 0" hexmask.long.byte 0x00 8.--15. 1. " SCR ,Serial Clock Rate" bitfld.long 0x00 7. " SPH ,SCLKOUT Phase" "Low,High" bitfld.long 0x00 6. " SPO ,SCLKOUT Polarity" "Low,High" textline " " bitfld.long 0x00 4.--5. " FRF ,Frame Format" "SPI,TI serial,Microwire,Reserved" bitfld.long 0x00 0.--3. " DSS ,Data Size Select" "Reserved,Reserved,Reserved,4-bit,5-bit,6-bit,7-bit,8-bit,9-bit,10-bit,11-bit,12-bit,13-bit,14-bit,15-bit,?..." line.long 0x04 "SSPCR1,Control Register 1" bitfld.long 0x04 6. " SOD ,Slave-Mode Output Disable" "Drive SSPTXD,Not drive SSPTXD" bitfld.long 0x04 5. " MS ,Master/Slave Mode Select" "Master,Slave" bitfld.long 0x04 4. " SSE ,Synchronous Serial Port Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 3. " LBM ,Loop Back Mode" "Normal,Loop Back" bitfld.long 0x04 2. " RORIE ,Receive FIFO Overrun Interrupt Enable" "Disabled,Enabled" bitfld.long 0x04 1. " TIE ,Transmit FIFO Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x04 0. " RIE ,Receive FIFO Interrupt Enable" "Disabled,Enabled" group asd:0x0008++3 line.long 0x00 "SSPDR,Transmit/Receive FIFO" hexmask.long.word 0x00 0.--15. 1. " DATA ,Data" rgroup asd:0x000C++3 line.long 0x00 "SSPSR,Status Register" bitfld.long 0x00 4. " BSY ,SSP Busy Flag" "Idle,Busy" bitfld.long 0x00 3. " RFF ,Receive FIFO Full" "Not full,Full" bitfld.long 0x00 2. " RNE ,Receive FIFO not Empty" "Empty,Not empty" textline " " bitfld.long 0x00 1. " TNF ,Transmit FIFO not Full" "Full,Not full" bitfld.long 0x00 0. " TFE ,Tramsnit FIFO Empty" "Not empty,Empty" group asd:0x0010++3 line.long 0x00 "SSPCPSR,Clock Prescale Register" hexmask.long.byte 0x00 0.--7. 1. " CPSDVSR ,Clock Pre-scale Divisior" rgroup asd:0x0014++3 line.long 0x00 "SSPIIR,Interrupt Identification Register" bitfld.long 0x00 2. " RORIS ,SSP Receive FIFO Overrun Interrupt Status" "Not asserted,Asserted" bitfld.long 0x00 1. " TIS ,SSP Transmit FIFO Service Request Interrupt Status" "Not asserted,Asserted" bitfld.long 0x00 0. " RIS ,SSP Receive FIFO Service Request Interrupt Status" "Not asserted,Asserted" wgroup asd:0x0014++3 line.long 0x00 "SSPICR,Interrupt Clear Register" ;end include file ep9312/ssp.ph tree.end tree "Pulse Width Modulator" base asd:0x80910000 ;begin include file ep9312/pwm.ph ;parameters: group asd:0x0000++1 "Output 0" line.word 0x00 "PWM0TermCnt,PWM0 Terminal Count" hexmask.word 0x00 0.--15. 1. " PWM_TC ,Terminal Count" group asd:0x0004++1 line.word 0x00 "PWM0DutyCycle,PWM0 Duty Cycle" hexmask.word 0x00 0.--15. 1. " PWM_DC ,Duty Cycle" group asd:0x0008++1 line.word 0x00 "PWM0En,PWM0 Enable" bitfld.word 0x00 0. " EN ,PWM Enable" "Disabled,Enabled" group asd:0x000C++1 line.word 0x00 "PWM0Invert,PWM0 Invert" bitfld.word 0x00 0. " EN ,Invert PWM Output" "Not inverted,Inverted" group asd:0x0010++1 line.word 0x00 "PWM0Sync,PWM0 Synchronous Register" group asd:0x0020++1 "Output 1" line.word 0x00 "PWM1TermCnt,PWM1 Terminal Count" hexmask.word 0x00 0.--15. 1. " PWM_TC ,Terminal Count" group asd:0x0024++1 line.word 0x00 "PWM1DutyCycle,PWM1 Duty Cycle" hexmask.word 0x00 0.--15. 1. " PWM_DC ,Duty Cycle" group asd:0x0028++1 line.word 0x00 "PWM1En,PWM1 Enable" bitfld.word 0x00 0. " EN ,PWM Enable" "Disabled,Enabled" group asd:0x002C++1 line.word 0x00 "PWM1Invert,PWM1 Invert" bitfld.word 0x00 0. " EN ,Invert PWM Output" "Not inverted,Inverted" group asd:0x0030++1 line.word 0x00 "PWM1Sync,PWM1 Synchronous Register" ;end include file ep9312/pwm.ph tree.end tree "Analog Touch Screen Interface" base asd:0x80900000 ;begin include file ep9312/touch.ph ;parameters: group asd:0x0000++7 line.long 0x00 "TSSetup,Analog Resistive Touch Screen Controller Setup Control Register" bitfld.long 0x00 31. " TDTCT ,Touch Detect" "Not detect,Detect" hexmask.long.word 0x00 16.--25. 1. " DLY ,Time Between Changes to Touch Screen Drive Conditions" bitfld.long 0x00 15. " EN ,Touch Screen Scan Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 12.--14. " DEV ,Max/Min Range Deviation in Sample Set" "+/-4 LSB,+/-8 LSB,+/-12 LSB,+/-16 LSB,+/-24 LSB,+/-32 LSB,+/-64 LSB,+/-128 LSB" bitfld.long 0x00 10.--11. " NSMP ,Number of Samples per X or Y" "4,8,16,32" hexmask.long.word 0x00 0.--9. 1. " SDLY ,Time Between A/D Samples" line.long 0x04 "TSXYMaxMin,Analog Resistive Touch Screen Controller Max/Min Register" hexmask.long.byte 0x04 24.--31. 1. " YMAX[11:4] ,Y Distance from a Previous Touch that Represents an Invalid Data Point" hexmask.long.byte 0x04 16.--23. 1. " XMAX[11:4] ,X Distance from a Previous Touch that Represents an Invalid Data Point" hexmask.long.byte 0x04 8.--15. 1. " YMIN[7:0] ,Y Distance from a Previous Touch to New Touch" textline " " hexmask.long.byte 0x04 0.--7. 1. " XMIN[7:0] ,X Distance from a Previous Touch to New Touch" rgroup asd:0x0008++3 line.long 0x00 "TSXYResult,Analog Resistive Touch Screen Controller Result Register" bitfld.long 0x00 31. " SDR ,Synchronous Data Ready" "Not ready,Ready" hexmask.long.word 0x00 16.--27. 1. " Y ,Y Controller Calculated Reading" hexmask.long.byte 0x00 12.--15. 1. " AD ,Analog Data" textline " " hexmask.long.word 0x00 0.--11. 1. " AD_X ,Analog Data X " group asd:0x000C++0x13 line.long 0x00 "TSDischarge,Analog Resistive Touch Screen Controller Switch Matrix Control Register" bitfld.long 0x00 29. " SCTL[29] ,Analog Switch Control Value when Controller Disabled" "Low,High" hexmask.long 0x00 0.--28. 1. " SCTL ,Analog Switch Control Value" line.long 0x04 "TSXSample,Analog Resistive Touch Screen Controller Switch Matrix Control Register" bitfld.long 0x04 29. " SCTL[29] ,Analog Switch Control Value when Controller Disabled" "Low,High" hexmask.long 0x04 0.--28. 1. " SCTL ,Analog Switch Control Value" line.long 0x08 "TSYSample,Analog Resistive Touch Screen Controller Switch Matrix Control Register" bitfld.long 0x08 29. " SCTL[29] ,Analog Switch Control Value when Controller Disabled" "Low,High" hexmask.long 0x08 0.--28. 1. " SCTL ,Analog Switch Control Value" line.long 0x0C "TSDirect,Analog Resistive Touch Screen Controller Switch Matrix Control Register" bitfld.long 0x0C 29. " SCTL[29] ,Analog Switch Control Value when Controller Disabled" "Low,High" hexmask.long 0x0C 0.--28. 1. " SCTL ,Analog Switch Control Value" line.long 0x10 "TSDetect,Analog Resistive Touch Screen Controller Switch Matrix Control Register" bitfld.long 0x10 29. " SCTL[29] ,Analog Switch Control Value when Controller Disabled" "Low,High" hexmask.long 0x10 0.--28. 1. " SCTL ,Analog Switch Control Value" wgroup asd:0x0020++3 line.long 0x00 "TSSWLock,Analog Resistive Touch Screen Controller Software Lock Register" hexmask.long.byte 0x00 0.--7. 1. " SWLOCK ,Unlock Value" rgroup asd:0x0020++3 line.long 0x00 "TSSWLock,Analog Resistive Touch Screen Controller Software Lock Register" bitfld.long 0x00 0. " SWLCK[0] ,Software Lock Status" "Locked,Unlocked" group asd:0x0024++3 line.long 0x00 "TSSetup2,Analog Resistive Touch Screen Controller Setup Control Register #2" bitfld.long 0x00 11. " RINTEN ,Synchronous Data Ready Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 10. " S28EN ,Switch 28 Enable" "Disabled,Enabled" bitfld.long 0x00 9. " NSIGND ,Unasigned ADC Output Type" "Signed,Unsigned" textline " " bitfld.long 0x00 8. " DISDEV ,Disable Deviation Check for Both X and Y ADC Sampling" "Enabled,Disabled" bitfld.long 0x00 7. " DTMEN ,Deviation Timer Enable" "Disabled,Enabled" bitfld.long 0x00 6. " DINTEN ,Deviation Error Interrupt Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 5. " DEVINT ,Deviation Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 4. " PINTEN ,Pen Up Interrupt Enable" "Disabled,Enabled" bitfld.long 0x00 3. " PENSTS ,Pen Status" "Pen up,Pen down" textline " " bitfld.long 0x00 2. " PINT ,Pen Up Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 1. " NICOR ,No Interrupt Clear on Read" "TINT clears,Manual" bitfld.long 0x00 0. " TINT ,Touch Interrupt" "No interrupt,Interrupt" ;end include file ep9312/touch.ph tree.end tree "Keypad Interface" base asd:0x808F0000 ;begin include file ep9312/keypad.ph ;parameters: group asd:0x0000++7 line.long 0x00 "KeyScanInt,Key Scan Initialization Register" hexmask.long.byte 0x00 16.--23. 1. " DBNC ,De-bounce Start Count" bitfld.long 0x00 15. " DIS3KY ,Disable 3 Key Reset" "Enabled,Disabled" bitfld.long 0x00 14. " DIAG ,Key Scan Diagnostic Mode" "Normal mode,Diagnostic" textline " " bitfld.long 0x00 13. " BACK ,Key Scan Back Driving Enable" "Disabled,Enabled" bitfld.long 0x00 12. " T2 ,Test Mode Bit" "No test mode,Test mode" hexmask.long.word 0x00 0.--9. 1. " PRSCL ,Row/Column Counter Prescaler Load Value" line.long 0x04 "KeyDiagnostic,Key Scan Diagnostic Register" hexmask.long.byte 0x04 0.--5. 1. " DIAG ,Diagnostic Key Value" rgroup asd:0x0008++3 line.long 0x00 "KeyRegister,Key Value Capture Register" bitfld.long 0x00 15. " KX ,Output of Key Array Column Multiplexer" "No key pressed,Key presed" bitfld.long 0x00 14. " INT ,Key Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 13. " 2KEYS ,Two Keys Detected" "Not detected,Detected" textline " " bitfld.long 0x00 12. " 1KEY ,At Leat One Key Detected" "Not detected,Detected" hexmask.long.byte 0x00 6.--11. 1. " KEY2 ,Row/Column Double Key Press Value" hexmask.long.byte 0x00 0.--5. 1. " KEY2 ,Row/Column Single Key Press Value" ;end include file ep9312/keypad.ph tree.end tree "IDE Interface" base asd:0x800A0000 ;begin include file ep9312/ide.ph ;parameters: group asd:0x0000++0x0F line.long 0x00 "IDECtrl,IDE Control Register" bitfld.long 0x00 10. " IORDY ,IORDY Pin Input State" "Low,High" bitfld.long 0x00 9. " INTRQ ,INTRQ Pin Input State" "Low,High" bitfld.long 0x00 8. " DMARQ ,DMARQ Pin Input State" "Low,High" textline " " bitfld.long 0x00 7. " DASPn ,DASPn Pin Input State" "Low,High" bitfld.long 0x00 6. " DIOWn ,DIOWn Pin Output Control" "Low,High" bitfld.long 0x00 5. " DIORn ,DIORn Pin Output Control" "Low,High" textline " " hexmask.long.byte 0x00 2.--4. 1. " DA ,Device Address Output Control" bitfld.long 0x00 1. " CS1n ,Chip Select 1 Pin Output Control" "Low,High" bitfld.long 0x00 0. " CS0n ,Chip Select 0 Pin Output Control" "Low,High" line.long 0x04 "IDECfg,IDE Configuration Register" bitfld.long 0x04 8.--9. " WST ,Wait State for Turn" "0,1,2,3" hexmask.long.byte 0x04 4.--7. 1. " MODE ,Speed Mode Number" bitfld.long 0x04 3. " UDMA ,Ultra DMA Operation Selection" "No UDMA,UDMA" textline " " bitfld.long 0x04 2. " MDMA ,Multiword DMA Operation Selection" "No MDMA,MDMA" bitfld.long 0x04 1. " PIO ,Pooled IO Operation Selection" "No PIO,PIO" bitfld.long 0x04 0. " IDEEN ,IDE Master Enable" "Disabled,Enabled" line.long 0x08 "IDEMDMAOp,IDE MDMA Operation Register" bitfld.long 0x08 1. " RWOP ,Read/Write Operation Selection" "Read,Write" bitfld.long 0x08 0. " MEN ,Enable Multiword DMA Operation" "Disabled,Enabled" line.long 0x0C "IDEUDMAOp,IDE UDMA Operation Register" bitfld.long 0x0C 1. " RWOP ,Read/Write Operation Selection" "Read,Write" bitfld.long 0x0C 0. " UEN ,Enable Ultra DMA Operation" "Disabled,Enabled" group asd:0x0010++3 line.long 0x00 "IDEDataOut,IDE PIO Data Output Register" hexfld.long 0x00 " IDEDD ,IDE Output Data" rgroup asd:0x0014++3 line.long 0x00 "IDEDataIn,IDE Data Input Register" hexfld.long 0x00 " IDEDD ,IDE Input Data" wgroup asd:0x0018++3 line.long 0x00 "IDEMDMADataOut,IDE MDMA Data Output Register" hexfld.long 0x00 " IDEDD ,IDE MDMA Output Data" rgroup asd:0x001C++3 line.long 0x00 "IDEMDMADataIn,IDE MDMA Data Input Register" hexfld.long 0x00 " IDEDD ,IDE MDMA Input Data" wgroup asd:0x0020++3 line.long 0x00 "IDEUDMADataOut,IDE UDMA Data Output Register" hexfld.long 0x00 " IDEDD ,IDE UDMA Output Data" rgroup asd:0x0024++3 line.long 0x00 "IDEUDMADataIn,IDE UDMA Data Input Register" hexfld.long 0x00 " IDEDD ,IDE UDMA Input Data" rgroup asd:0x0028++3 line.long 0x00 "IDEUDMASts,IDE UDMA Status Register" bitfld.long 0x00 26. " N4X ,Data Transferred Not Multiplies of 4 32-bit Words Error" "No error,Error" bitfld.long 0x00 25. " NDI ,Data In Not Completed Error" "No error,Error" bitfld.long 0x00 24. " NDO ,Data Out Not Completed Error" "No error,Error" textline " " bitfld.long 0x00 18. " SBUSY ,UDMA Busy" "Not busy,Busy" bitfld.long 0x00 17. " INTIde ,UDMA Error Interrupt" "No interrupt,Interrupt" bitfld.long 0x00 16. " DMAIde ,DMA Signal from UDMA Request" "Not requested,Requested" textline " " bitfld.long 0x00 10. " DSDD ,DSTROBE and DDMARDYn Status" "Low,High" bitfld.long 0x00 9. " DMARQ ,DMARQ Synchronized Input from Device" "Low,High" bitfld.long 0x00 8. " DDOE ,DD Bus Output Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 7. " DM ,DMACKn Status" "Low,High" bitfld.long 0x00 6. " STOP ,STOP Status" "Not stopped,Stopped" bitfld.long 0x00 5. " HSHD ,HSTROBE and HDMARDYn Status" "Low,High" textline " " hexmask.long.byte 0x00 2.--4. 1. " DA ,Device Address Status" bitfld.long 0x00 1. " CS1n ,Chip Select Pin 1 Status" "Low,High" bitfld.long 0x00 0. " CS0n ,Chip Select Pin 0 Status" "Low,High" group asd:0x002C++3 line.long 0x00 "IDEUDMADebug,IDE UDMA Debug Register" bitfld.long 0x00 5. " RRDR ,Reset UDMA Read DMA Request" "No reset,Reset" bitfld.long 0x00 4. " RRPTR ,Reset UDMA Read Buffer Pointer to 0" "No reset,Reset" bitfld.long 0x00 3. " RROE ,Reset UDMA Read Data In Error" "No reset,Reset" textline " " bitfld.long 0x00 2. " RWDR ,Reset UDMA Write DMA Request" "No reset,Reset" bitfld.long 0x00 1. " RWPTR ,Reset UDMA Write Buffer Pointer to 0" "No reset,Reset" bitfld.long 0x00 0. " RWOE ,Reset UDMA Write Data Out Error" "No reset,Reset" rgroup asd:0x0030++7 line.long 0x00 "IDEUDMAWrBufSts,IDE UDMA Write Buffer Status Register" hexmask.long.word 0x00 16.--31. 1. " CRC ,CRC Result for Data-Out Operation" bitfld.long 0x00 11. " FULL ,Write Buffer Full" "Not full,Full" bitfld.long 0x00 10. " NFULL ,Write Buffer Near Full Status" "Not near full,Near full" textline " " bitfld.long 0x00 9. " HOM ,Half or More Entries In Write Buffer Filled" "Not filled,Filled" bitfld.long 0x00 8. " EMPTY ,Write Buffer Empty" "Not empty,Empty" hexmask.long.byte 0x00 4.--7. 1. " TPTR ,Tail Pointer In Write Buffer" textline " " hexmask.long.byte 0x00 0.--3. 1. " HPTR ,Head Pointer In Write Buffer" line.long 0x04 "IDEUDMARdBufSts,IDE UDMA Read Buffer Status Register" hexmask.long.word 0x04 16.--31. 1. " CRC ,CRC Result for Data-In Operation" bitfld.long 0x04 11. " FULL ,Read Buffer Full" "Not full,Full" bitfld.long 0x04 10. " NFULL ,Read Buffer Near Full Status" "Not near full,Near full" textline " " bitfld.long 0x04 9. " HOM ,Half or More Entries In Read Buffer Filled" "Not filled,Filled" bitfld.long 0x04 8. " EMPTY ,Read Buffer Empty" "Not empty,Empty" hexmask.long.byte 0x04 4.--7. 1. " TPTR ,Tail Pointer In Read Buffer" textline " " hexmask.long.byte 0x04 0.--3. 1. " HPTR ,Head Pointer In Read Buffer" ;end include file ep9312/ide.ph tree.end tree "GPIO Interface" base asd:0x80840000 ;begin include file ep9312/gpio.ph ;parameters: tree "PORT A" base asd:0x80840000 ;begin include file ep9312/gpio/portabcd.ph ;parameters: 0x0000 A group asd:0x0000++3 line.long 0x00 "PADR,Port A Data Register" bitfld.long 0x00 7. " PAData7 ,Port A Data Pin 7" "Low,High" bitfld.long 0x00 6. " PAData6 ,Port A Data Pin 6" "Low,High" bitfld.long 0x00 5. " PAData5 ,Port A Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PAData4 ,Port A Data Pin 4" "Low,High" bitfld.long 0x00 3. " PAData3 ,Port A Data Pin 3" "Low,High" bitfld.long 0x00 2. " PAData2 ,Port A Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PAData1 ,Port A Data Pin 1" "Low,High" bitfld.long 0x00 0. " PAData0 ,Port A Data Pin 0" "Low,High" group asd:(0x0000+0x0010)++3 line.long 0x00 "PADDR,Port A Data Direction Register" bitfld.long 0x00 7. " PADIR7 ,Port A Direction Pin 7" "Input,Output" bitfld.long 0x00 6. " PADIR6 ,Port A Direction Pin 6" "Input,Output" bitfld.long 0x00 5. " PADIR5 ,Port A Direction Pin 5" "Input,Output" textline " " bitfld.long 0x00 4. " PADIR4 ,Port A Direction Pin 4" "Input,Output" bitfld.long 0x00 3. " PADIR3 ,Port A Direction Pin 3" "Input,Output" bitfld.long 0x00 2. " PADIR2 ,Port A Direction Pin 2" "Input,Output" textline " " bitfld.long 0x00 1. " PADIR1 ,Port A Direction Pin 1" "Input,Output" bitfld.long 0x00 0. " PADIR0 ,Port A Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portabcd.ph ;begin include file ep9312/gpio/intabf.ph ;parameters: 0x0090 A group asd:(0x0090+0x000C)++3 line.long 0x00 "GPIOAIntEn,GPIO A Interrupt Enable" bitfld.long 0x00 7. " PAINT7 ,Port A Interrupt Enable Pin 7" "Disabled,Enabled" bitfld.long 0x00 6. " PAINT6 ,Port A Interrupt Enable Pin 6" "Disabled,Enabled" bitfld.long 0x00 5. " PAINT5 ,Port A Interrupt Enable Pin 5" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PAINT4 ,Port A Interrupt Enable Pin 4" "Disabled,Enabled" bitfld.long 0x00 3. " PAINT3 ,Port A Interrupt Enable Pin 3" "Disabled,Enabled" bitfld.long 0x00 2. " PAINT2 ,Port A Interrupt Enable Pin 2" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PAINT1 ,Port A Interrupt Enable Pin 1" "Disabled,Enabled" bitfld.long 0x00 0. " PAINT0 ,Port A Interrupt Enable Pin 0" "Disabled,Enabled" group asd:0x0090++7 line.long 0x00 "GPIOAIntType1,GPIO A Interrupt Type Regiter 1" bitfld.long 0x00 7. " PAINTE7 ,Pin 7 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 6. " PAINTE6 ,Pin 6 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 5. " PAINTE5 ,Pin5 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 4. " PAINTE4 ,Pin 4 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 3. " PAINTE3 ,Pin 3 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 2. " PAINTE2 ,Pin 2 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 1. " PAINTE1 ,Pin 1 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 0. " PAINTE0 ,Pin 0 Level/Edge Sensitive" "Level,Edge" line.long 0x04 "GPIOAIntType2,GPIO A Interrupt Type Regiter 2" bitfld.long 0x04 7. " PAINTE7 ,Pin 7 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 6. " PAINTE6 ,Pin 6 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 5. " PAINTE5 ,Pin 5 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 4. " PAINTE4 ,Pin 4 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 3. " PAINTE3 ,Pin 3 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 2. " PAINTE2 ,Pin 2 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 1. " PAINTE1 ,Pin 1 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 0. " PAINTE0 ,Pin 0 Falling/Rising Sensitive" "Falling edge,Rising edge" wgroup asd:(0x0090+0x0008)++3 line.long 0x00 "GPIOAEOI,GPIO A End of Interrupt Register" bitfld.long 0x00 7. " PAINTC7 ,Interrupt Clear on Pin 7" "No effect,Clear" bitfld.long 0x00 6. " PAINTC6 ,Interrupt Clear on Pin 6" "No effect,Clear" bitfld.long 0x00 5. " PAINTC5 ,Interrupt Clear on Pin 5" "No effect,Clear" textline " " bitfld.long 0x00 4. " PAINTC4 ,Interrupt Clear on Pin 4" "No effect,Clear" bitfld.long 0x00 3. " PAINTC3 ,Interrupt Clear on Pin 3" "No effect,Clear" bitfld.long 0x00 2. " PAINTC2 ,Interrupt Clear on Pin 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " PAINTC1 ,Interrupt Clear on Pin 1" "No effect,Clear" bitfld.long 0x00 0. " PAINTC0 ,Interrupt Clear on Pin 0" "No effect,Clear" group asd:(0x0090+0x0018)++3 line.long 0x00 "GPIOADB,GPIO A Debounce Enable" bitfld.long 0x00 7. " PAINTDB7 ,Pin 7 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 6. " PAINTDB6 ,Pin 6 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 5. " PAINTDB5 ,Pin 5 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PAINTDB4 ,Pin 4 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 3. " PAINTDB3 ,Pin 3 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PAINTDB2 ,Pin 2 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PAINTDB1 ,Pin 1 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 0. " PAINTDB0 ,Pin 0 Debounce Enable" "Disabled,Enabled" rgroup asd:(0x0090+0x0014)++3 line.long 0x00 "RawIntStsA,GPIO A Raw Interrupt Status" bitfld.long 0x00 7. " PAINTRS7 ,Pin 7 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 6. " PAINTRS6 ,Pin 6 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 5. " PAINTRS5 ,Pin 5 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 4. " PAINTRS4 ,Pin 4 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 3. " PAINTRS3 ,Pin 3 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 2. " PAINTRS2 ,Pin 2 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 1. " PAINTRS1 ,Pin 1 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 0. " PAINTRS0 ,Pin 0 Raw Interrupt Status" "Not Signalled,Signalled" rgroup asd:(0x0090+0x0010)++3 line.long 0x00 "IntStsA,GPIO A Interrupt Status" bitfld.long 0x00 7. " PAINTS7 ,Pin 7 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 6. " PAINTS6 ,Pin 6 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 5. " PAINTS5 ,Pin 5 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 4. " PAINTS4 ,Pin 4 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 3. " PAINTS3 ,Pin 3 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 2. " PAINTS2 ,Pin 2 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " PAINTS1 ,Pin 1 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 0. " PAINTS0 ,Pin 0 Masked Interrupt Status" "No interrupt,Interrupt" ;end include file ep9312/gpio/intabf.ph tree.end tree "PORT B" base asd:0x80840000 ;begin include file ep9312/gpio/portabcd.ph ;parameters: 0x0004 B group asd:0x0004++3 line.long 0x00 "PBDR,Port B Data Register" bitfld.long 0x00 7. " PBData7 ,Port B Data Pin 7" "Low,High" bitfld.long 0x00 6. " PBData6 ,Port B Data Pin 6" "Low,High" bitfld.long 0x00 5. " PBData5 ,Port B Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PBData4 ,Port B Data Pin 4" "Low,High" bitfld.long 0x00 3. " PBData3 ,Port B Data Pin 3" "Low,High" bitfld.long 0x00 2. " PBData2 ,Port B Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PBData1 ,Port B Data Pin 1" "Low,High" bitfld.long 0x00 0. " PBData0 ,Port B Data Pin 0" "Low,High" group asd:(0x0004+0x0010)++3 line.long 0x00 "PBDDR,Port B Data Direction Register" bitfld.long 0x00 7. " PBDIR7 ,Port B Direction Pin 7" "Input,Output" bitfld.long 0x00 6. " PBDIR6 ,Port B Direction Pin 6" "Input,Output" bitfld.long 0x00 5. " PBDIR5 ,Port B Direction Pin 5" "Input,Output" textline " " bitfld.long 0x00 4. " PBDIR4 ,Port B Direction Pin 4" "Input,Output" bitfld.long 0x00 3. " PBDIR3 ,Port B Direction Pin 3" "Input,Output" bitfld.long 0x00 2. " PBDIR2 ,Port B Direction Pin 2" "Input,Output" textline " " bitfld.long 0x00 1. " PBDIR1 ,Port B Direction Pin 1" "Input,Output" bitfld.long 0x00 0. " PBDIR0 ,Port B Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portabcd.ph ;begin include file ep9312/gpio/intabf.ph ;parameters: 0x00AC B group asd:(0x00AC+0x000C)++3 line.long 0x00 "GPIOBIntEn,GPIO B Interrupt Enable" bitfld.long 0x00 7. " PBINT7 ,Port B Interrupt Enable Pin 7" "Disabled,Enabled" bitfld.long 0x00 6. " PBINT6 ,Port B Interrupt Enable Pin 6" "Disabled,Enabled" bitfld.long 0x00 5. " PBINT5 ,Port B Interrupt Enable Pin 5" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PBINT4 ,Port B Interrupt Enable Pin 4" "Disabled,Enabled" bitfld.long 0x00 3. " PBINT3 ,Port B Interrupt Enable Pin 3" "Disabled,Enabled" bitfld.long 0x00 2. " PBINT2 ,Port B Interrupt Enable Pin 2" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PBINT1 ,Port B Interrupt Enable Pin 1" "Disabled,Enabled" bitfld.long 0x00 0. " PBINT0 ,Port B Interrupt Enable Pin 0" "Disabled,Enabled" group asd:0x00AC++7 line.long 0x00 "GPIOBIntType1,GPIO B Interrupt Type Regiter 1" bitfld.long 0x00 7. " PBINTE7 ,Pin 7 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 6. " PBINTE6 ,Pin 6 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 5. " PBINTE5 ,Pin5 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 4. " PBINTE4 ,Pin 4 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 3. " PBINTE3 ,Pin 3 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 2. " PBINTE2 ,Pin 2 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 1. " PBINTE1 ,Pin 1 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 0. " PBINTE0 ,Pin 0 Level/Edge Sensitive" "Level,Edge" line.long 0x04 "GPIOBIntType2,GPIO B Interrupt Type Regiter 2" bitfld.long 0x04 7. " PBINTE7 ,Pin 7 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 6. " PBINTE6 ,Pin 6 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 5. " PBINTE5 ,Pin 5 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 4. " PBINTE4 ,Pin 4 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 3. " PBINTE3 ,Pin 3 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 2. " PBINTE2 ,Pin 2 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 1. " PBINTE1 ,Pin 1 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 0. " PBINTE0 ,Pin 0 Falling/Rising Sensitive" "Falling edge,Rising edge" wgroup asd:(0x00AC+0x0008)++3 line.long 0x00 "GPIOBEOI,GPIO B End of Interrupt Register" bitfld.long 0x00 7. " PBINTC7 ,Interrupt Clear on Pin 7" "No effect,Clear" bitfld.long 0x00 6. " PBINTC6 ,Interrupt Clear on Pin 6" "No effect,Clear" bitfld.long 0x00 5. " PBINTC5 ,Interrupt Clear on Pin 5" "No effect,Clear" textline " " bitfld.long 0x00 4. " PBINTC4 ,Interrupt Clear on Pin 4" "No effect,Clear" bitfld.long 0x00 3. " PBINTC3 ,Interrupt Clear on Pin 3" "No effect,Clear" bitfld.long 0x00 2. " PBINTC2 ,Interrupt Clear on Pin 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " PBINTC1 ,Interrupt Clear on Pin 1" "No effect,Clear" bitfld.long 0x00 0. " PBINTC0 ,Interrupt Clear on Pin 0" "No effect,Clear" group asd:(0x00AC+0x0018)++3 line.long 0x00 "GPIOBDB,GPIO B Debounce Enable" bitfld.long 0x00 7. " PBINTDB7 ,Pin 7 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 6. " PBINTDB6 ,Pin 6 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 5. " PBINTDB5 ,Pin 5 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PBINTDB4 ,Pin 4 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 3. " PBINTDB3 ,Pin 3 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PBINTDB2 ,Pin 2 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PBINTDB1 ,Pin 1 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 0. " PBINTDB0 ,Pin 0 Debounce Enable" "Disabled,Enabled" rgroup asd:(0x00AC+0x0014)++3 line.long 0x00 "RawIntStsB,GPIO B Raw Interrupt Status" bitfld.long 0x00 7. " PBINTRS7 ,Pin 7 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 6. " PBINTRS6 ,Pin 6 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 5. " PBINTRS5 ,Pin 5 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 4. " PBINTRS4 ,Pin 4 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 3. " PBINTRS3 ,Pin 3 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 2. " PBINTRS2 ,Pin 2 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 1. " PBINTRS1 ,Pin 1 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 0. " PBINTRS0 ,Pin 0 Raw Interrupt Status" "Not Signalled,Signalled" rgroup asd:(0x00AC+0x0010)++3 line.long 0x00 "IntStsB,GPIO B Interrupt Status" bitfld.long 0x00 7. " PBINTS7 ,Pin 7 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 6. " PBINTS6 ,Pin 6 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 5. " PBINTS5 ,Pin 5 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 4. " PBINTS4 ,Pin 4 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 3. " PBINTS3 ,Pin 3 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 2. " PBINTS2 ,Pin 2 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " PBINTS1 ,Pin 1 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 0. " PBINTS0 ,Pin 0 Masked Interrupt Status" "No interrupt,Interrupt" ;end include file ep9312/gpio/intabf.ph tree.end tree "PORT C" base asd:0x80840000 ;begin include file ep9312/gpio/portabcd.ph ;parameters: 0x0008 C group asd:0x0008++3 line.long 0x00 "PCDR,Port C Data Register" bitfld.long 0x00 7. " PCData7 ,Port C Data Pin 7" "Low,High" bitfld.long 0x00 6. " PCData6 ,Port C Data Pin 6" "Low,High" bitfld.long 0x00 5. " PCData5 ,Port C Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PCData4 ,Port C Data Pin 4" "Low,High" bitfld.long 0x00 3. " PCData3 ,Port C Data Pin 3" "Low,High" bitfld.long 0x00 2. " PCData2 ,Port C Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PCData1 ,Port C Data Pin 1" "Low,High" bitfld.long 0x00 0. " PCData0 ,Port C Data Pin 0" "Low,High" group asd:(0x0008+0x0010)++3 line.long 0x00 "PCDDR,Port C Data Direction Register" bitfld.long 0x00 7. " PCDIR7 ,Port C Direction Pin 7" "Input,Output" bitfld.long 0x00 6. " PCDIR6 ,Port C Direction Pin 6" "Input,Output" bitfld.long 0x00 5. " PCDIR5 ,Port C Direction Pin 5" "Input,Output" textline " " bitfld.long 0x00 4. " PCDIR4 ,Port C Direction Pin 4" "Input,Output" bitfld.long 0x00 3. " PCDIR3 ,Port C Direction Pin 3" "Input,Output" bitfld.long 0x00 2. " PCDIR2 ,Port C Direction Pin 2" "Input,Output" textline " " bitfld.long 0x00 1. " PCDIR1 ,Port C Direction Pin 1" "Input,Output" bitfld.long 0x00 0. " PCDIR0 ,Port C Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portabcd.ph tree.end tree "PORT D" base asd:0x80840000 ;begin include file ep9312/gpio/portabcd.ph ;parameters: 0x000C D group asd:0x000C++3 line.long 0x00 "PDDR,Port D Data Register" bitfld.long 0x00 7. " PDData7 ,Port D Data Pin 7" "Low,High" bitfld.long 0x00 6. " PDData6 ,Port D Data Pin 6" "Low,High" bitfld.long 0x00 5. " PDData5 ,Port D Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PDData4 ,Port D Data Pin 4" "Low,High" bitfld.long 0x00 3. " PDData3 ,Port D Data Pin 3" "Low,High" bitfld.long 0x00 2. " PDData2 ,Port D Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PDData1 ,Port D Data Pin 1" "Low,High" bitfld.long 0x00 0. " PDData0 ,Port D Data Pin 0" "Low,High" group asd:(0x000C+0x0010)++3 line.long 0x00 "PDDDR,Port D Data Direction Register" bitfld.long 0x00 7. " PDDIR7 ,Port D Direction Pin 7" "Input,Output" bitfld.long 0x00 6. " PDDIR6 ,Port D Direction Pin 6" "Input,Output" bitfld.long 0x00 5. " PDDIR5 ,Port D Direction Pin 5" "Input,Output" textline " " bitfld.long 0x00 4. " PDDIR4 ,Port D Direction Pin 4" "Input,Output" bitfld.long 0x00 3. " PDDIR3 ,Port D Direction Pin 3" "Input,Output" bitfld.long 0x00 2. " PDDIR2 ,Port D Direction Pin 2" "Input,Output" textline " " bitfld.long 0x00 1. " PDDIR1 ,Port D Direction Pin 1" "Input,Output" bitfld.long 0x00 0. " PDDIR0 ,Port D Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portabcd.ph tree.end tree "PORT E" base asd:0x80840000 ;begin include file ep9312/gpio/portefgh.ph ;parameters: 0x0020 E group asd:0x0020++7 line.long 0x00 "PEDR,Port E Data Register" bitfld.long 0x00 7. " PEData7 ,Port E Data Pin 7" "Low,High" bitfld.long 0x00 6. " PEData6 ,Port E Data Pin 6" "Low,High" bitfld.long 0x00 5. " PEData5 ,Port E Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PEData4 ,Port E Data Pin 4" "Low,High" bitfld.long 0x00 3. " PEData3 ,Port E Data Pin 3" "Low,High" bitfld.long 0x00 2. " PEData2 ,Port E Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PEData1 ,Port E Data Pin 1" "Low,High" bitfld.long 0x00 0. " PEData0 ,Port E Data Pin 0" "Low,High" line.long 0x04 "PEDDR,Port E Data Direction Register" bitfld.long 0x04 7. " PEDIR7 ,Port E Direction Pin 7" "Input,Output" bitfld.long 0x04 6. " PEDIR6 ,Port E Direction Pin 6" "Input,Output" bitfld.long 0x04 5. " PEDIR5 ,Port E Direction Pin 5" "Input,Output" textline " " bitfld.long 0x04 4. " PEDIR4 ,Port E Direction Pin 4" "Input,Output" bitfld.long 0x04 3. " PEDIR3 ,Port E Direction Pin 3" "Input,Output" bitfld.long 0x04 2. " PEDIR2 ,Port E Direction Pin 2" "Input,Output" textline " " bitfld.long 0x04 1. " PEDIR1 ,Port E Direction Pin 1" "Input,Output" bitfld.long 0x04 0. " PEDIR0 ,Port E Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portefgh.ph tree.end tree "PORT F" base asd:0x80840000 ;begin include file ep9312/gpio/portefgh.ph ;parameters: 0x0030 F group asd:0x0030++7 line.long 0x00 "PFDR,Port F Data Register" bitfld.long 0x00 7. " PFData7 ,Port F Data Pin 7" "Low,High" bitfld.long 0x00 6. " PFData6 ,Port F Data Pin 6" "Low,High" bitfld.long 0x00 5. " PFData5 ,Port F Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PFData4 ,Port F Data Pin 4" "Low,High" bitfld.long 0x00 3. " PFData3 ,Port F Data Pin 3" "Low,High" bitfld.long 0x00 2. " PFData2 ,Port F Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PFData1 ,Port F Data Pin 1" "Low,High" bitfld.long 0x00 0. " PFData0 ,Port F Data Pin 0" "Low,High" line.long 0x04 "PFDDR,Port F Data Direction Register" bitfld.long 0x04 7. " PFDIR7 ,Port F Direction Pin 7" "Input,Output" bitfld.long 0x04 6. " PFDIR6 ,Port F Direction Pin 6" "Input,Output" bitfld.long 0x04 5. " PFDIR5 ,Port F Direction Pin 5" "Input,Output" textline " " bitfld.long 0x04 4. " PFDIR4 ,Port F Direction Pin 4" "Input,Output" bitfld.long 0x04 3. " PFDIR3 ,Port F Direction Pin 3" "Input,Output" bitfld.long 0x04 2. " PFDIR2 ,Port F Direction Pin 2" "Input,Output" textline " " bitfld.long 0x04 1. " PFDIR1 ,Port F Direction Pin 1" "Input,Output" bitfld.long 0x04 0. " PFDIR0 ,Port F Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portefgh.ph ;begin include file ep9312/gpio/intabf.ph ;parameters: 0x004C F group asd:(0x004C+0x000C)++3 line.long 0x00 "GPIOFIntEn,GPIO F Interrupt Enable" bitfld.long 0x00 7. " PFINT7 ,Port F Interrupt Enable Pin 7" "Disabled,Enabled" bitfld.long 0x00 6. " PFINT6 ,Port F Interrupt Enable Pin 6" "Disabled,Enabled" bitfld.long 0x00 5. " PFINT5 ,Port F Interrupt Enable Pin 5" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PFINT4 ,Port F Interrupt Enable Pin 4" "Disabled,Enabled" bitfld.long 0x00 3. " PFINT3 ,Port F Interrupt Enable Pin 3" "Disabled,Enabled" bitfld.long 0x00 2. " PFINT2 ,Port F Interrupt Enable Pin 2" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PFINT1 ,Port F Interrupt Enable Pin 1" "Disabled,Enabled" bitfld.long 0x00 0. " PFINT0 ,Port F Interrupt Enable Pin 0" "Disabled,Enabled" group asd:0x004C++7 line.long 0x00 "GPIOFIntType1,GPIO F Interrupt Type Regiter 1" bitfld.long 0x00 7. " PFINTE7 ,Pin 7 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 6. " PFINTE6 ,Pin 6 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 5. " PFINTE5 ,Pin5 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 4. " PFINTE4 ,Pin 4 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 3. " PFINTE3 ,Pin 3 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 2. " PFINTE2 ,Pin 2 Level/Edge Sensitive" "Level,Edge" textline " " bitfld.long 0x00 1. " PFINTE1 ,Pin 1 Level/Edge Sensitive" "Level,Edge" bitfld.long 0x00 0. " PFINTE0 ,Pin 0 Level/Edge Sensitive" "Level,Edge" line.long 0x04 "GPIOFIntType2,GPIO F Interrupt Type Regiter 2" bitfld.long 0x04 7. " PFINTE7 ,Pin 7 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 6. " PFINTE6 ,Pin 6 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 5. " PFINTE5 ,Pin 5 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 4. " PFINTE4 ,Pin 4 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 3. " PFINTE3 ,Pin 3 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 2. " PFINTE2 ,Pin 2 Falling/Rising Sensitive" "Falling edge,Rising edge" textline " " bitfld.long 0x04 1. " PFINTE1 ,Pin 1 Falling/Rising Sensitive" "Falling edge,Rising edge" bitfld.long 0x04 0. " PFINTE0 ,Pin 0 Falling/Rising Sensitive" "Falling edge,Rising edge" wgroup asd:(0x004C+0x0008)++3 line.long 0x00 "GPIOFEOI,GPIO F End of Interrupt Register" bitfld.long 0x00 7. " PFINTC7 ,Interrupt Clear on Pin 7" "No effect,Clear" bitfld.long 0x00 6. " PFINTC6 ,Interrupt Clear on Pin 6" "No effect,Clear" bitfld.long 0x00 5. " PFINTC5 ,Interrupt Clear on Pin 5" "No effect,Clear" textline " " bitfld.long 0x00 4. " PFINTC4 ,Interrupt Clear on Pin 4" "No effect,Clear" bitfld.long 0x00 3. " PFINTC3 ,Interrupt Clear on Pin 3" "No effect,Clear" bitfld.long 0x00 2. " PFINTC2 ,Interrupt Clear on Pin 2" "No effect,Clear" textline " " bitfld.long 0x00 1. " PFINTC1 ,Interrupt Clear on Pin 1" "No effect,Clear" bitfld.long 0x00 0. " PFINTC0 ,Interrupt Clear on Pin 0" "No effect,Clear" group asd:(0x004C+0x0018)++3 line.long 0x00 "GPIOFDB,GPIO F Debounce Enable" bitfld.long 0x00 7. " PFINTDB7 ,Pin 7 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 6. " PFINTDB6 ,Pin 6 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 5. " PFINTDB5 ,Pin 5 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 4. " PFINTDB4 ,Pin 4 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 3. " PFINTDB3 ,Pin 3 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 2. " PFINTDB2 ,Pin 2 Debounce Enable" "Disabled,Enabled" textline " " bitfld.long 0x00 1. " PFINTDB1 ,Pin 1 Debounce Enable" "Disabled,Enabled" bitfld.long 0x00 0. " PFINTDB0 ,Pin 0 Debounce Enable" "Disabled,Enabled" rgroup asd:(0x004C+0x0014)++3 line.long 0x00 "RawIntStsF,GPIO F Raw Interrupt Status" bitfld.long 0x00 7. " PFINTRS7 ,Pin 7 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 6. " PFINTRS6 ,Pin 6 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 5. " PFINTRS5 ,Pin 5 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 4. " PFINTRS4 ,Pin 4 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 3. " PFINTRS3 ,Pin 3 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 2. " PFINTRS2 ,Pin 2 Raw Interrupt Status" "Not Signalled,Signalled" textline " " bitfld.long 0x00 1. " PFINTRS1 ,Pin 1 Raw Interrupt Status" "Not Signalled,Signalled" bitfld.long 0x00 0. " PFINTRS0 ,Pin 0 Raw Interrupt Status" "Not Signalled,Signalled" rgroup asd:(0x004C+0x0010)++3 line.long 0x00 "IntStsF,GPIO F Interrupt Status" bitfld.long 0x00 7. " PFINTS7 ,Pin 7 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 6. " PFINTS6 ,Pin 6 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 5. " PFINTS5 ,Pin 5 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 4. " PFINTS4 ,Pin 4 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 3. " PFINTS3 ,Pin 3 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 2. " PFINTS2 ,Pin 2 Masked Interrupt Status" "No interrupt,Interrupt" textline " " bitfld.long 0x00 1. " PFINTS1 ,Pin 1 Masked Interrupt Status" "No interrupt,Interrupt" bitfld.long 0x00 0. " PFINTS0 ,Pin 0 Masked Interrupt Status" "No interrupt,Interrupt" ;end include file ep9312/gpio/intabf.ph tree.end tree "PORT G" base asd:0x80840000 ;begin include file ep9312/gpio/portefgh.ph ;parameters: 0x0038 G group asd:0x0038++7 line.long 0x00 "PGDR,Port G Data Register" bitfld.long 0x00 7. " PGData7 ,Port G Data Pin 7" "Low,High" bitfld.long 0x00 6. " PGData6 ,Port G Data Pin 6" "Low,High" bitfld.long 0x00 5. " PGData5 ,Port G Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PGData4 ,Port G Data Pin 4" "Low,High" bitfld.long 0x00 3. " PGData3 ,Port G Data Pin 3" "Low,High" bitfld.long 0x00 2. " PGData2 ,Port G Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PGData1 ,Port G Data Pin 1" "Low,High" bitfld.long 0x00 0. " PGData0 ,Port G Data Pin 0" "Low,High" line.long 0x04 "PGDDR,Port G Data Direction Register" bitfld.long 0x04 7. " PGDIR7 ,Port G Direction Pin 7" "Input,Output" bitfld.long 0x04 6. " PGDIR6 ,Port G Direction Pin 6" "Input,Output" bitfld.long 0x04 5. " PGDIR5 ,Port G Direction Pin 5" "Input,Output" textline " " bitfld.long 0x04 4. " PGDIR4 ,Port G Direction Pin 4" "Input,Output" bitfld.long 0x04 3. " PGDIR3 ,Port G Direction Pin 3" "Input,Output" bitfld.long 0x04 2. " PGDIR2 ,Port G Direction Pin 2" "Input,Output" textline " " bitfld.long 0x04 1. " PGDIR1 ,Port G Direction Pin 1" "Input,Output" bitfld.long 0x04 0. " PGDIR0 ,Port G Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portefgh.ph tree.end tree "PORT H" base asd:0x80840000 ;begin include file ep9312/gpio/portefgh.ph ;parameters: 0x0040 H group asd:0x0040++7 line.long 0x00 "PHDR,Port H Data Register" bitfld.long 0x00 7. " PHData7 ,Port H Data Pin 7" "Low,High" bitfld.long 0x00 6. " PHData6 ,Port H Data Pin 6" "Low,High" bitfld.long 0x00 5. " PHData5 ,Port H Data Pin 5" "Low,High" textline " " bitfld.long 0x00 4. " PHData4 ,Port H Data Pin 4" "Low,High" bitfld.long 0x00 3. " PHData3 ,Port H Data Pin 3" "Low,High" bitfld.long 0x00 2. " PHData2 ,Port H Data Pin 2" "Low,High" textline " " bitfld.long 0x00 1. " PHData1 ,Port H Data Pin 1" "Low,High" bitfld.long 0x00 0. " PHData0 ,Port H Data Pin 0" "Low,High" line.long 0x04 "PHDDR,Port H Data Direction Register" bitfld.long 0x04 7. " PHDIR7 ,Port H Direction Pin 7" "Input,Output" bitfld.long 0x04 6. " PHDIR6 ,Port H Direction Pin 6" "Input,Output" bitfld.long 0x04 5. " PHDIR5 ,Port H Direction Pin 5" "Input,Output" textline " " bitfld.long 0x04 4. " PHDIR4 ,Port H Direction Pin 4" "Input,Output" bitfld.long 0x04 3. " PHDIR3 ,Port H Direction Pin 3" "Input,Output" bitfld.long 0x04 2. " PHDIR2 ,Port H Direction Pin 2" "Input,Output" textline " " bitfld.long 0x04 1. " PHDIR1 ,Port H Direction Pin 1" "Input,Output" bitfld.long 0x04 0. " PHDIR0 ,Port H Direction Pin 0" "Input,Output" ;end include file ep9312/gpio/portefgh.ph tree.end textline "" ;begin include file ep9312/gpio/ee.ph ;parameters: group asd:0x00C8++3 line.long 0x00 "EEDrive,EEPROM Interface Pin Drive Type Control" bitfld.long 0x00 1. " DATOD ,EEDAT Pin Output Driver" "Low,High" bitfld.long 0x00 0. " CLKOD ,EECLK Pin Output Driver" "Low,High" ;end include file ep9312/gpio/ee.ph ;end include file ep9312/gpio.ph tree.end tree "Security" base asd:0x80830000 ;begin include file ep9312/security.ph ;parameters: rgroup asd:0x2714++3 line.long 0x00 "ExtensionID,Part ID for EP93xx Devices" hexmask.long.byte 0x00 1.--8. 1. " PartID ,Identification Number" ;end include file ep9312/security.ph tree.end