; --------------------------------------------------------------------------------
; @Title: eMMC FLASH Programming script for OMAP4430
; @Description:
; eMMC FLASH(SanDisk, iNAND 8GBytes) is connected
;
; Internal SRAM: 0x40301000
;
; SD/MMC Controller Register : 0x480B4200 (MMCHS2)          
; SD/MMC Controller Register : 0x4809C200 (MMCHS1)          
;
;
; @Author: jjeong
; @Chip: OMAP4430
; @Keywords: SanDisk iNAND eMMC
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
; --------------------------------------------------------------------------------
; $Id: omap4430-emmc.cmm 10516 2022-02-02 11:39:30Z bschroefel $

LOCAL &arg1
ENTRY &arg1
&arg1=STRing.UPpeR("&arg1")  // for example "PREPAREONLY"


WinCLEAR
AREA.view

LOCAL &MMCHS

&MMCHS=0x4809C200   ;on MMCHS1
;&MMCHS=0x480B4200  ;on MMCHS2
&MMC_BASE=&MMCHS

SYStem.RESet
SYStem.CPU omap4430

SYStem.JtagClock 10.Mhz

SYStem.Option DACR ON  ; Give Debugger global write permissions
SETUP.IMASKASM OFF     ; Lock interrupts while single stepping
SYStem.MemAccess DAP   ; Enable DAP access

TrOnchip.Set DABORT OFF
TrOnchip.Set PABORT OFF
TrOnchip.Set UNDEF  OFF

SYStem.Mode.Go

IF STATE.RUN()
Break.direct

  PER.Set.simple C15:0x1 %Long  (Data.Long(C15:0x1)&~(0x5))  ; disable interrupt and mmu

  GOSUB disable_watchdog

  Data.Set &MMCHS+0x2C %LE %Long 0xe3C87     ; 400Khz 
  Data.Set &MMCHS+0x34 %LE %Long 0x307f0033  ; enable the BRR bit


GOSUB READ_ID_TEST

  Break.RESet

  FLASHFILE.RESet

//FLASHFILE.CONFIG <MMC Controller Base>  0x0   0x0
  FLASHFILE.CONFIG &MMCHS             0x0   0x0

//FLASHFILE.target <Code_range>       <Data_range>       <Algorithm file>
  FLASHFILE.TARGET 0x40301000++0x1FFF 0x40303000++0x2FFF   ~~/demo/arm/flash/byte/emmc_omap.bin /KEEP  ; for eMMC flash
; FLASHFILE.TARGET 0x40301000++0x1FFF 0x40303000++0x2FFF   ~~/demo/arm/flash/byte/emmcsd_omap.bin /keep  ;for SDCARD

  Data.Set &MMCHS+0x2C %LE %Long 0xE3C87     ; 400Khz , the Card identification mode
  FLASHFILE.GETID
  Data.Set &MMCHS+0x2C %LE %Long 0xE1087     ; higher clock speed for the Data transfer mode
  FLASHFILE.GETEXTCSD
  
  //End of the test prepareonly
  IF "&arg1"=="PREPAREONLY"
  ENDDO
  
  DIALOG.YESNO "Program flash memory?"
  ENTRY &progflash
  IF &progflash 
  (
 
  //Erase FLASH 
    FLASHFILE.Erase 0x0--0xFFFFFF  

  //Write FLASH
    FLASHFILE.LOAD.binary  * 0x0 
  
  //Verify FLASH
    ; FLASHFILE.LOAD  * 0x0  /ComPare
  )

  //Dump FLASH
  FLASHFILE.DUMP 0x0

ENDDO 


disable_watchdog:
(

 PRINT "DISABLE WATCHDOG ..."

 // Enable Clock
 Data.Set SR:0x4A307830 %Long 0x02
 
 // Check that module is IDLE
 WHILE ((Data.Long(SR:0x4A307830)&0x20000)==0x20000) 
 
 // Wait until reset complete 
   WHILE ((Data.Long(SR:0x4A314014)&0x01)!=0x1)
  
 //Disable watchdog timer
 Data.Set SR:0x4A314048 %LE %Long 0x0000AAAA;
  WHILE ((Data.Long(SR:0x4A314034)&0x10)==0x10)

 Data.Set SR:0x4A314048 %LE %Long 0x00005555;
 WHILE ((Data.Long(SR:0x4A314034)&0x10)==0x10)
)

RETURN


READ_ID_TEST:
//MMC interface, not SD(HC)
//CMD0
RePeaT 2.
(
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x0  ;arg 
Data.Set &MMC_BASE+0xc %Long 0x0  ;cmd
WAIT 10.ms
)

//CMD1
RePeaT 10.
(
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x40FF8000 ;arg
Data.Set &MMC_BASE+0xc %Long 0x01020000 ;cmd1
WAIT 100.ms
&resp=Data.Long(A:(&MMC_BASE+0x10))
//print "CMD1 resp: 0x" &resp
IF (&resp&0x80000000)==0x80000000
(
GOTO jump_cmd2
)
)

PRINT "CMD1 fail"
END

jump_cmd2:
//CMD2
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x0     ;arg
Data.Set &MMC_BASE+0xc %Long 0x02010000 ;cmd2
WAIT 10.ms

//CMD3
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x00010000  ; arg, MMC RCA is (0x0001<<16.)
Data.Set &MMC_BASE+0xc %Long 0x03020000  ;cmd3
WAIT 10.ms

//CMD10
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x00010000 ; arg, MMC RCA is (0x0001<<16.)
Data.Set &MMC_BASE+0xc %Long 0x0A010000  ;cmd10
WAIT 10.ms

//Response2
PRINT "CID register"
PRINT "[127:104] 0x" Data.Long(A:(&MMC_BASE+0x1c))
PRINT "[103:72]  0x" Data.Long(A:(&MMC_BASE+0x18))
PRINT "[71:40]   0x" Data.Long(A:(&MMC_BASE+0x14))
PRINT "[39:8]    0x" Data.Long(A:(&MMC_BASE+0x10))

RETURN