; --------------------------------------------------------------------------------
; @Title: IVT On-Chip Peripherals
; @Props: Released
; @Author: DAB
; @Changelog: 2022-02-23 DAB
; @Manufacturer: NXP - NXP Semiconductors
; @Doc:
; @Core: Cortex-A53, Cortex-R52, Cortex-M7, Cortex-M33
; @Chip: S32G2* S32G3* S32R45* S32R41* SAF85XX* S32S247TV* S32Z27* S32E27*
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
; --------------------------------------------------------------------------------
; $Id: pers32_ivt.per 15945 2023-04-11 07:39:41Z skrausse $

tree "IVT Table (QSPI)"
base ad:0x00
width 58.
group.long 0x00++0x03
line.long 0x00 "IVT header,Header Showing The Start Of The IVT"
hexmask.long.byte 0x00 24.--31. 1. " TAG         ,Tag"
newline
hexmask.long.word 0x00 8.--23. 1. " LEN         ,Length"
newline
hexmask.long.byte 0x00 0.--7. 1. " VER         ,Version"
group.long 0x08++0x27
line.long 0x00 "Self-Test DCD pointer,Pointer to the start of the configuration data used for BIST"
line.long 0x04 "Self-Test DCD pointer (backup),Pointer to the start of the backup configuration data used for BIST"
line.long 0x08 "DCD_pointer,Pointer to the start of DCD configuration data"
line.long 0x0C "DCD_pointer (backup),Pointer to the start of backup DCD configuration data"
line.long 0x10 "HSE_H firmware flash memory start pointer,Pointer to the start of the HSE_H firmware in flash memory"
line.long 0x14 "HSE_H firmware flash memory start pointer (backup),Pointer to the start of the backup HSE_H firmware in flash memory"
line.long 0x18 "Application_boot code flash memory start pointer,Pointer to the start of the application boot code in flash memory"
line.long 0x1C "Application_boot code flash memory start pointer (backup),Pointer to the start of the backup application boot code in flash memory"
line.long 0x20 "Boot_configuration word,Configuration data used to select the boot configuration"
bitfld.long 0x20 3. " BOOT_SEQ    ,Secure boot mode" "Non-secure,Secure"
newline
bitfld.long 0x20 2. " SWT         ,Boot target watchdog" "Disabled,Enabled"
newline
bitfld.long 0x20 0.--1. " BOOT_TARGET ,Boot target" "Cortex-M7_0,Cortex-A53_0,?..."
line.long 0x24 "Life cycle configuration word,Configuration data used for advancing life cycle"
bitfld.long 0x24 1. " IN_FIELD    ,Advances life cycle state to IN_FIELD" "Disabled,Enabled"
newline
bitfld.long 0x24 0. " OEM_PROD    ,Advances life cycle state to OEM_PROD" "Disabled,Enabled"
repeat 8. (increment 0x34 0x04) (increment 0. 1.)
group.long $1++0x03
line.long 0x00 "HSE_H firmware $2,Defined by the HSE_H firmware specification"
repeat.end
newline
repeat 4. (increment 0xF0 0x04) (increment 0. 1.)
group.long $1++0x03
line.long 0x00 "GMAC$2,Galois Message Authentication Code of first 240 bytes of IVT image structure"
repeat.end
tree "DCD Registers"
base ad:((per.l(ad:0x00+0x10))&0xFFFFFFFF)
width 26.
group.long 0x00++0x03
line.long 0x00 "DCD header,Header to signify start of DCD data"
hexmask.long.byte 0x00 24.--31. 1. " TAG      ,Tag"
hexmask.long.word 0x00 8.--23. 1. "               LEN       ,Length"
hexmask.long.byte 0x00 0.--7. 1. "           VER   ,Version"
group.byte 0x04++0x01 "DCD data"
line.byte 0x00 "Write Data Parameters,Write data command parameters"
bitfld.byte 0x00 4. "     Data Set ,Status bit showing whether bits at target were successfully overwritten" "Not overwritten,Overwritten"
bitfld.byte 0x00 3. "  Data Mask ,Enables overwriting of bits at target address" "All bits,Specific bits"
bitfld.byte 0x00 0.--2. "  Bytes ,Width of target location(s) in bytes" ",1 byte,2 bytes,,4 bytes,?..."
line.byte 0x01 "Check Data Parameters,Check data command parameters"
bitfld.byte 0x01 4. "     Data Set ,Enables bit checking at target address" "Ignored,Checked"
bitfld.byte 0x01 3. "          Data Mask ,Enables partial/complete checking of bits when the Data Set field is set to 1" "All bits,Specific bits"
bitfld.byte 0x01 0.--2. "  Bytes ,Size of target locations in bytes." ",1 byte,2 bytes,,4 bytes,?..."
base ad:(((per.l(ad:((per.l(ad:0x00+0x10))&0xFFFFFFFF))>>8)&0xFFFF)+0x04)
group.long 0x000++0x03
line.long 0x00 "GMAC,Cryptographic hash for DCD header and complete DCD data using IVTDCD key"
width 0x0B
tree.end
tree "DCD Self-Test Registers"
base ad:((per.l(ad:0x00+0x08))&0xFFFFFFFF)
width 26.
group.long 0x00++0x03
line.long 0x00 "DCD SelfTest header,Header to signify start of DCD SelfTest data"
hexmask.long.byte 0x00 24.--31. 1. " TAG      ,Tag"
hexmask.long.word 0x00 8.--23. 1. "               LEN       ,Length"
hexmask.long.byte 0x00 0.--7. 1. "           VER   ,Version"
group.byte 0x04++0x01 "DCD data"
line.byte 0x00 "Write Data Parameters,Write data command parameters"
bitfld.byte 0x00 4. "     Data Set ,Status bit showing whether bits at target were successfully overwritten" "Not overwritten,Overwritten"
bitfld.byte 0x00 3. "  Data Mask ,Enables overwriting of bits at target address" "All bits,Specific bits"
bitfld.byte 0x00 0.--2. "  Bytes ,Width of target location(s) in bytes" ",1 byte,2 bytes,,4 bytes,?..."
line.byte 0x01 "Check Data Parameters,Check data command parameters"
bitfld.byte 0x01 4. "     Data Set ,Enables bit checking at target address" "Ignored,Checked"
bitfld.byte 0x01 3. "          Data Mask ,Enables partial/complete checking of bits when the Data Set field is set to 1" "All bits,Specific bits"
bitfld.byte 0x01 0.--2. "  Bytes ,Size of target locations in bytes." ",1 byte,2 bytes,,4 bytes,?..."
base ad:(((per.l(ad:((per.l(ad:0x00)+0x08)&0xFFFFFFFF))>>8)&0xFFFF)+0x04)
group.long 0x00++0x03
line.long 0x00 "GMAC,Cryptographic hash for DCD header and complete DCD data using IVTDCD key"
width 0x0B
tree.end
tree "BOOT Registers"
base ad:((per.l(ad:0x00+0x20))&0xFFFFFFFF)
width 24.
if (((per.l(ad:0x00+0x28)&0x08)==0))
group.long 0x00++0x0F "Application boot"
line.long 0x00 "Image header,Marks start of application image"
hexmask.long.byte 0x00 24.--31. 1. " TAG                    ,Tag"
newline
hexmask.long.byte 0x00 0.--7. 1. " Version                ,Version"
line.long 0x04 "RAM start pointer,Pointer to the first RAM address to which BootROM must load application boot code"
line.long 0x08 "RAM entry pointer,Pointer to out of RESET start of boot target core. For Cortex-M7 it corresponds to VTOR. For A53 it corresponds to start of code execution"
line.long 0x0C "Code length word,Length of code section of the image"
group.long 0x40++0x03
line.long 0x00 "Code,Code can be any size up to the maximum size of system SRAM"
sif cpuis("Cortex-M7")
group.long 0x00++0x0B "Serial boot"
line.long 0x00 "Image header,Marks start of serial boot code image"
hexmask.long.byte 0x00 24.--31. 1. " TAG                    ,Tag"
hexmask.long.byte 0x00 0.--7. 1. "        Version                 ,Version"
line.long 0x04 "RAM start pointer,Pointer to the first RAM address to which BootROM must load serial boot code"
line.long 0x08 "RAM entry pointer,Pointer to out of RESET start of boot target core. For Cortex-M7 it corresponds to VTOR"
group.long 0x40++0x03
line.long 0x00 "Code,Code can be any size up to the maximum size of system SRAM"
endif
else
sif cpuis("CortexM7")
group.long 0x00++0x17 "Serial boot"
line.long 0x00 "Image header,Marks start of serial boot code image"
hexmask.long.byte 0x00 24.--31. 1. " TAG                    ,Tag"
hexmask.long.byte 0x00 0.--7. 1. "        Version                 ,Version"
line.long 0x04 "RAM start pointer,Pointer to the first RAM address to which BootROM must load serial boot code"
line.long 0x08 "RAM entry pointer,Pointer to out of RESET start of boot target core. For Cortex-M7 it corresponds to VTOR"
line.long 0x0C "Code length word,Length of code section of the image."
line.long 0x10 "Auth mode,Authentication mode"
line.long 0x14 "NSKPUB Key Selector,NSK public key selector"
group.long 0x40++0x03
line.long 0x00 "Code,Code can be any size up to the maximum size of system SRAM."
repeat 64. (increment 0x1040 0x04)(increment 0. 1.)
group.long $1++0x03
line.long 0x00 "CSKPUB$2,Customer Public key for RSA authentication $2"
repeat.end
repeat 64. (increment 0x1140 0x04) (increment 0. 1.)
group.long $1++0x03
line.long 0x00 "CSK Signature $2,RSA signature for CSKPUB authentication $2"
repeat.end
group.long 0x1240++0x03
line.long 0x00 "Code,Code can be any size up to the maximum size of SRAM"
base ad:per.l(ad:((per.l(ad:0x00+0x20))&0xFFFFFFFF)+0x0C)
repeat 64. (increment 0x1240 0x04) (increment 0. 1.)
group.long ($1+0x0C)++0x03
line.long 0x00 "Public key Signature $2,Public key signature for image authentication $2"
repeat.end
endif
endif
width 0x0B
tree.end
width 0x0B
tree.end